INSTALLATION INSTRUCTIONS Display Carts MFC, PFC Series
Installation Instructions MFC, PFC Series DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
MFC, PFC Series Installation Instructions DIMENSIONS MFC PFC 3
Installation Instructions MFC, PFC Series LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro
Installation Instructions MFC, PFC Series TOOLS REQUIRED FOR INSTALLATION 3/16" (Included) PARTS B (1) [right leg] A (1) [left leg] D (4) [snap-on cover] C (2) [end cap] E (1) [center post] F (1) [cross bracket] G (1) PFC Head Assembly K (1) 3/16" L (4) 5/16-18 x 3/4" M (4) 5/16-18 x 2-3/4" H (1) MFC Head Assembly N (4) 5/16-18 x 4-1/4" J (1) 3/16" [drill bit] P (4) 5/16" 5
MFC, PFC Series Installation Instructions ASSEMBLY inner column CAUTION: Attachment holes may be damaged if a power drill is used to insert button head cap screws. Screws should first be inserted and turned BY HAND with the hex key or with a handheld screwdriver BEFORE using the hex head drill bit (J) and power drill to complete the attachment. Cable Tie Assembling Cart 1.
Installation Instructions MFC, PFC Series IMPORTANT ! : When attaching head assembly ensure that the ClickConnect lock is at TOP of head assembly, and bracket tabs slide into the stand assembly. (See Figure 5) 1. 2. Slide head assembly (G) or (H) into the stand assembly. (See Figure 5) Attach head assembly (G) or (H) to the cart assembly using four 5/16-18 x 3/4" button head cap screws (L). (See Figure 5) ClickConnect lock at TOP of head assembly 2 (L) x 4 (G) or (H) Grasp head assembly .
MFC, PFC Series Installation Instructions Attaching Display to Cart WARNING: IMPROPER INSTALLATION CAN LEAD TO WARNING: EXCEEDING MAXIMUM WEIGHT CAPACITY MAY LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s responsibility to ensure the total amount of weight placed on the cart does not exceed 125 lbs (56.70 kg) for the MFC, and 200 lbs (90.72 kg) for the PFC.
Installation Instructions MFC, PFC Series Tilting Display The display can be tilted up to 15o either backward or forward from a straight upright position. 1. Turn knob counterclockwise on back of head assembly to loosen the tilt. (See Figure 11) (Rear view of center post) 2 (Front view of center post) 1 3 Exits for signal cables 1 3 lock display Place optional bolt (not provided) here 4 to lock in an upright position. (D) Exit for power cables (MFC Shown) Figure 11 2.
MFC, PFC Series Installation Instructions Cart Use and Maintenance CAUTION: This cart is intended for use only with the products and maximum weights indicated (125 lbs [56.70 kg] for the MFC, and 200 lbs [90.72 kg] for the PFC). Use with other products or products heavier than the maximum weights indicated may result in instability causing possible injury. WARNING: CART CAN TIP OVER RESULTING IN RISK OF INJURY. Do not allow children under 16 to move cart. Only adults should move this cart.
Installation Instructions MFC, PFC Series Removing Display from Cart 1. Remove bolt or padlock from faceplate (if used). (See Figure 15) NOTE: The pin may have been used as a more permanent locking device. If so, remove nut and pin and move from the lower holes to the upper holes. 2. Pull back on flag on upper mounting hole and press pin down into "Open" position.
MFC, PFC Series Installation Instructions USA/International Chief Manufacturing, a products division of Milestone AV Technologies 8809-000038 RevG 2010 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 08/10 Europe Asia Pacific A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.6918 Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands +31 (0)40 2668620 +31 (0)40 2668615 Office No.
