INSTALLATION INSTRUCTIONS Display Carts MFC Series
MFC Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
MFC Series Installation Instructions DIMENSIONS NOTE: MSBU INTERFACE BRACKET NOT SHOWN. THE MSBU INTERFACE BRACKET NEEDED FOR DISPLAY WILL ADD 1” IN DEPTH AND MAY AFFECT LOCATION OF THE DISPLAY ON THE MOUNT.
Installation Instructions MFC Series LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Beves
MFC Series Installation Instructions TOOLS REQUIRED FOR INSTALLATION 3/16" (Included) PARTS A (1) [left leg] D (4) [snap-on cover] E (1) [center post] B (1) [right leg] C (2) [end cap] H (1) 3/16" [drill bit] F (1) [cross bracket] G (1) [MFC head assembly] K (4) 5/16-18 x 3/4" L (4) 5/16-18 x 2-3/4" M (4) 5/16-18 x 4-1/4" J (1) 3/16" N (4) 5/16" P (1) [MSBU interface bracket included only with MFCU] 5
MFC Series Installation Instructions ASSEMBLY inner column CAUTION: Attachment holes may be damaged if a power drill is used to insert button head cap screws. Screws should first be inserted and turned BY HAND with the hex key or with a hand held screwdriver BEFORE using the hex head drill bit (J) and power drill to complete the attachment. Cable Tie Assembling Cart 1.
Installation Instructions MFC Series IMPORTANT ! : When attaching head assembly ensure that the ClickConnect lock is at TOP of head assembly, and bracket tabs slide into the stand assembly. (See Figure 5) 1. 2. Slide head assembly (G) into the stand assembly. (See Figure 5) Attach head assembly (G) to the cart assembly using four 5/16-18 x 3/4" button head cap screws (K). (See Figure 5) ClickConnect lock at TOP of head assembly (K) x 4 2 (G) Grasp head assembly within shaded area. Figure 6 2.
MFC Series Installation Instructions Attaching Display to Cart WARNING: Display may be very heavy! Ensure display may be safely lifted and maneuvered as required to install on cart.
Installation Instructions MFC Series Tilting Display The display can be tilted up to 15o either backward or forward from a straight upright position. 1. Turn knob counterclockwise on back of head assembly to loosen the tilt. (See Figure 11) (Rear view of center post) 2 (Front view of center post) 1 3 Exits for signal cables 1 3 lock display Place optional bolt (not provided) here 4 to lock in an upright position. (D) Exit for power cables Figure 11 2.
MFC Series Installation Instructions NOTE: The MFC Series cart has no user serviceable parts. Cart Use and Maintenance NOTE: The MFC Series cart can support screen sizes up to a maximum of 55" wide. WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components located between the MFC Series cart up to (and including) the display does not exceed 125 lbs (56.
Installation Instructions MFC Series Removing Display from Cart 1. Remove bolt or padlock from faceplate (if used). (See Figure 15) NOTE: The pin may have been used as a more permanent locking device. If so, remove nut and pin and move from the lower holes to the upper holes. 2. Pull back on flag on upper mounting hole and press pin down into "Open" position.
MFC Series Installation Instructions USA/International Chief, a products division of Milestone AV Technologies 8800-002572 Rev00 2014 Milestone AV Technologies www.chiefmfg.com 05/14 Europe Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.