INSTALLATION INSTRUCTIONS Display Carts MFC Series
MFC Series Installation Instructions DISCLAIMER Legrand | AV and its affiliated corporations and subsidiaries (collectively “Legrand | AV”), intend to make this manual accurate and complete. However, Legrand | AV makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
[96 X 86] 3 3/4" X 3 3/8" TUBE DIMENSIONS: [MILLIMETERS] INCHES 729 28 3/4" SEE MSBU DRAWING ALSO. [81 X 51] 3 1/4" X 2" TUBE NOTE: CUSTOM INTERFACE BRACKET NOT SHOWN. THE CUSTOM INTERFACE BRACKET NEEDED FOR YOUR DISPLAY WILL ADD BETWEEN 1/2" AND 2" IN DEPTH AND MAY AFFECT LOCATION OF DISPLAY ON THE MOUNT.
Installation Instructions MFC Series LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Beves
MFC Series Installation Instructions TOOLS REQUIRED FOR INSTALLATION 3/16" (Included) PARTS A (1) [left leg] D (4) [snap-on cover] B (1) [right leg] E (1) [center post] C (2) [end cap] F (1) [cross bracket] G (1) [MFC head assembly] H (1) 3/16" [drill bit] L (4) 5/16-18 x 2-3/4" 5 J (1) 3/16" M (4) 5/16-18 x 4-1/2" K (4) 5/16-18 x 1/2" N (4) 5/16" P (1) [MSBU interface bracket included only with MFCU]
MFC Series Installation Instructions ASSEMBLY inner column CAUTION: Attachment holes may be damaged if a power drill is used to insert button head cap screws. Screws should first be inserted and turned BY HAND with the hex key or with a hand held screwdriver BEFORE using the hex head drill bit (J) and power drill to complete the attachment. Cable Tie Assembling Cart 1.
Installation Instructions MFC Series IMPORTANT ! : When attaching head assembly ensure that the ClickConnect lock is at TOP of head assembly, and bracket tabs slide into the cart assembly. (See Figure 5) 1. 2. Slide head assembly (G) into the cart assembly. (See Figure 5) Attach head assembly (G) to the cart assembly using four 5/16-18 x 1/2" button head cap screws (K). (See Figure 5) ClickConnect lock at TOP of head assembly (K) x 4 2 (G) Grasp head assembly within shaded area.
MFC Series Installation Instructions Attaching Display to Cart WARNING: Display may be very heavy! Ensure display may be safely lifted and maneuvered as required to install on cart.
Installation Instructions MFC Series Tilting Display The display can be tilted up to 15o either backward or forward from a straight upright position. 1. Turn knob counterclockwise on back of head assembly to loosen the tilt. (See Figure 11) (Rear view of center post) 2 (Front view of center post) 1 3 Exits for signal cables 1 3 lock display Place optional bolt (not provided) here 4 to lock in an upright position. (D) Exit for power cables Figure 11 2.
MFC Series Installation Instructions Cart Use and Maintenance NOTE: The MFC Series cart has no user serviceable parts. NOTE: The MFC Series cart can support screen sizes up to a maximum of 55" wide. WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components located between the MFC Series cart up to (and including) the display does not exceed 125 lbs (56.
Installation Instructions MFC Series Removing Display from Cart 1. Remove bolt or padlock from faceplate (if used). (See Figure 15) NOTE: The pin may have been used as a more permanent locking device. If so, remove nut and pin and move from the lower holes to the upper holes. 2. Pull back on flag on upper mounting hole and press pin down into "Open" position.
MFC Series Installation Instructions USA/International Europe 8800-002958 Rev01 2020 Legrand | AV www.legrandav.com 01/2020 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.