INSTALLATION INSTRUCTIONS Large Shelf Accessory Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description PACCS1
PACCS1 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product.
Installation Instructions PACCS1 LEGEND Tighten Fastener Hex-Head Wrench Apretar elemento de fijación Llave de cabeza hexagonal Befestigungsteil festziehen Sechskantschlüssel Apertar fixador Chave de cabeça sextavada Serrare il fissaggio Chiave esagonale Bevestiging vastdraaien Zeskantsleutel Serrez les fixations Clé à tête hexagonale Loosen Fastener Open-Ended Wrench Aflojar elemento de fijación Llave de boca Befestigungsteil lösen Gabelschlüssel Desapertar fixador Chave de bocas Al
PACCS1 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 1/8" (included) #2 1/4" PARTS A (1) [Shelf Bracket] C (1) [Shelf] B (1) [Adjustment Bracket] G (4) [Rubber Bumper] D (1) [Right Upright] E (1) [Left Upright] N (4) 1/4-20 x 5/8" H (6) [Cable Tie] F (4) [Mounting Button] P (2) 1/4-20 x 5/8" J (2) 1" x 1" [Hook & Loop] K (1) 1/8" M (2) 1/4-20 L (6) 10-24 Q (2) 10-24 x 1/2" R (4) 10-24 x 7/8" S (2) 1/4" 4 T (1) 1/4-20 X 3/8"
Installation Instructions PACCS1 ASSEMBLY AND INSTALLATION NOTE: The PACCS1 is designed to accommodate both (E) 200mm x 200mm and 14" x 14" Q-latch mounting systems. If a 200mm x 200mm pattern is required, use the inner mounting holes on the shelf bracket (A) when installing the uprights (D and E). (See Figure 2) (L) x 2 3 Attachment for 200mm x 200mm NOTE: The 14" x 14" display mounting pattern is NOT identical to a 400 x 400 VESA display mounting pattern.
PACCS1 Installation Instructions 2. Verify latching flag is in the OPEN position. (See Figure 5) and (See Figure 6) 3. Align four mounting buttons on display with four teardrop mounting holes in accessory. (See Figure 5) and (See Figure 6) 4. Slide mounting buttons into teardrop mounting holes and lower display until recessed area of mounting buttons is seated in lower area of teardrop mounting holes.
Installation Instructions PACCS1 2. Reposition shelf up or down to desired position. (See Figure 7) 3. Tighten two button head cap screws securing adjustment bracket to shelf bracket using 1/8" hex wrench (K). (See Figure 7) Shelf Completely Retracted Cable Management Route cables and wires to display using cable ties (H) as necessary, and following manufacturers installation instructions. Installing Equipment on Shelf Using Strap 1.
PACCS1 Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8800-002050 Rev04 2012 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 07/12 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.
