INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation RPA Elite Series Projector Mounts Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description RPMA/RPMB/RPMC Series
RPMA/RPMB/RPMC Series Installation Instructions NOTE: RPMA, RPMB, and RPMC models are included in these installation instructions. Throughout these instructions "RPMX" is used to designate all of the models covered by these instructions. WARNING: Never operate this mounting system if it is damaged. Return the mounting system to a service center for examination and repair.
Installation Instructions RPMA/RPMB/RPMC Series DIMENSIONS 6.50 4.50 5.50 1.50" DIA NPT 5.50 YAW ADJUSTMENT POINT 20 1.00 PITCH ADJUSTMENT POINT 20 5.24 SECURITY LOCK 2.79 ROLL ADJUSTMENT POINT 3 SECURITY SWITCH TOOLS REQUIRED FOR INSTALLATION 3/32" (2.4mm) dia. (wood) 1/4" (6.4mm) dia.
RPMA/RPMB/RPMC Series Installation Instructions LEGEND 4 Tighten Fastener Pencil Mark Serrez les fixations Marquage au crayon Serrare il fissaggio Segno a matita Befestigungsteil festziehen Stiftmarkierung Apretar elemento de fijación Marcar con lápiz Bevestiging vastdraaien Potloodmerkteken Apertar fixador Marcar com lápis Loosen Fastener Drill Hole Desserrez les fixations Percez un trou Allentare il fissaggio Praticare un foro Befestigungsteil lösen Bohrloch Aflojar elemento de f
Installation Instructions RPMA/RPMB/RPMC Series PREPARATION Locate Mounting Site (not included) Threaded extension column (not included) WARNING: IMPROPER INSTALLATION MAY LEAD TO PROJECTOR MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installers responsibility to make certain the structure to which the projector mount is being mounted is capable of supporting five times the weight of the projector mount and all attached equipment.
RPMA/RPMB/RPMC Series Installation Instructions Installing to Wood Framework (Joists) 1. Using the RPMX as a guide, mark four mounting hole locations. (See Figure 3) 2. Drill four 3/32" (2.4mm) dia. pilot holes to a depth of 1-3/4" (45mm) deep. 1 x4 2 3 Pilot hole dimensions x4 4 Ø 2.4mm (Ø 3/32”) 45mm (1-3/4”) Figure 4 Figure 3 3. Align four mounting holes in RPMX with four pilot holes. 5.
Installation Instructions 3. RPMA/RPMB/RPMC Series Align four mounting holes in RPMX with four pilot holes. 4. IMPORTANT ! : When RPMX is properly positioned, the set screw access hole should be pointing directly at target, or 180° AWAY from target. Secure the threaded rods to the RPMX with #10-24 jam nuts (not included) and 1/4" washers (not included). (See Figure 7) Secure using 1 jam nuts WARNING: Anchors (not provided) must be installed into (not included) structurally sound solid concrete.
RPMA/RPMB/RPMC Series Installation Instructions YAW Adjustment (Rotation) WARNING: IMPROPER INSTALLATION CAN LEAD TO PROJECTOR FALLING RESULTING IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT. Make certain mounting slots in mount base slide under thumb screws and that screws are seated in the back of slots. 1. Loosen YAW adjustment locking screw using a #2 Phillips screwdriver. (See Figure 9) 2.
Installation Instructions RPMA/RPMB/RPMC Series Roll Adjustment (Horizontal Tilt) 1. Loosen ROLL adjustment locking screw using a #2 Phillips screwdriver. (See Figure 11) 2. Turn ROLL micro-adjustment screw right or left using a #2 Phillips screwdriver until image is properly aligned on target. 3. Tighten ROLL adjustment locking screw using a #2 Phillips screwdriver.
RPMA/RPMB/RPMC Series 10 Installation Instructions
Installation Instructions RPMA/RPMB/RPMC Series 11
RPMA/RPMB/RPMC Series Installation Instructions USA/International Europe Chief Manufacturing, a products division of Milestone AV Technologies 8800-002307 Rev00 2013 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 01/13 Asia Pacific A P F A P F A 6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No.