Datasheet

ManualsBrandsChief ManualsProjector AccessoriesSLB184

INSTALLATION INSTRUCTIONS

CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes no claim that the infor-

mation contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The

information contained in this document is subject to change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the

information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918

8802-000251

2/12/07

SLB-184 and SLM-184 Interface Brackets

SLB and SLM series Interface brackets are designed for use with Chief RPA, RPM, and Smart-Lift series projector mounts. See the specific

installation instructions provided with the mount for additional installation information.

Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative by calling

1-800-582-6480.

WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!

Installation:

WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE

TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.

NOTE: Step 1 is only required when installing an SLB Interface bracket. If an SLM bracket is being installed proceed to step 2.

1. Screw six thumb screws onto six 10-24 x 5/8" Philips pan head screws. DO NOT fully tighten thumb screws at this time.

2. Turn projector upside down on a flat surface.

3. Remove four adjustable feet in the bottom of projector.

4. Place interface bracket onto the bottom of the projector so the center hole is closer to the front of the projector well lining up the four holes

in the bracket with the four threaded inserts in the bottom of the projector.

5. Using the four M5 X 25mm mounting screws and M5 washers, start them into the mounting holes by hand and secure all four fasteners at

this time.

CAUTION: When attaching the mount be careful not to over tighten mounting screws.

6. Find the four M5 threaded holes provided in the bracket and thread one adjustable foot into each hole provided one to two turns.

(1) Interface Bracket (4) Screw, Philips Pan Head, Machine, M5 x 25mm

(6) 10-24 Thumb Nuts ** (4) Washer, M5

(1) All-Points Security Kit

**Only used when installing SLB Interface brackets.

Front of Projector

M5 tapped holes for

adjustable foot

storage

M5 tapped holes for

adjustable foot

storage

Summary of content (2 pages)

PAGE 1
INSTALLATION INSTRUCTIONS SLB-184 and SLM-184 Interface Brackets SLB and SLM series Interface brackets are designed for use with Chief RPA, RPM, and Smart-Lift series projector mounts. See the specific installation instructions provided with the mount for additional installation information. Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative by calling 1-800-582-6480.
PAGE 2
INSTALLATION INSTRUCTIONS Continued CAUTION: When screwing the adjustable feet into the four storage holes, make sure not to screw then in to far or you could damage your projector by hitting the plastic shell of the projector. These feet should not be tight; these holes are only to store the feet so they can be use again at a future time. NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the All-Points Security Kit.