INSTALLATION INSTRUCTIONS Wall Mount Speaker Bracket YSM2
YSM2 Installation Instructions DISCLAIMER CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind.
Installation Instructions YSM2 DIMENSIONS YSM-2 with YSP-1000 Speaker Measurements in: [millimeters] inches LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desaper
YSM2 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 7/32" (5.
Installation Instructions YSM2 INSTALLATION Wall Stud (A) WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installers responsibility to make certain the structure to which the mount is being attached is capable of supporting five times the weight of the YSM-2 and all attached equipment not to exceed 30 lbs (13.61 kg).
YSM2 Installation Instructions Steel Stud Installation - Site Requirements WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum reguirements for installation of display mounts onto a steel stud structure. If the structure or its components do not meet these requirements contact the mount manufacturer for specific instructions before attempting installation.
Installation Instructions YSM2 1. Using a stud finder, locate and mark the two studs to which the YSM-2 will be installed. 2. Using a nail through the center hole of the wall bracket (A), temporarily hang the wall bracket on the wall at the install location. (See Figure 1) 3. Align mounting holes in wall bracket (A) with studs. 4. Mark location of four mounting holes on wall. (See Figure 1) 5. Drill four pilot holes. (See Figure 1) 9.
YSM2 Installation Instructions overtighten mounting hardware! Steel Stud (B) Drywall (J) x 4 (K) x 4 Back of YSP-800 Speaker Wall Bracket (A) Anchor Metal Channel (C) (G) x 8 SIDE VIEW Figure 7 Figure 9 1. Attaching End Brackets to Speaker YSP-1000 Speakers NOTE: Ensure that hook on speaker brackets (B and C) point down and face inside of speaker. (See Figure 8) Attach speaker brackets to left and right side of speaker, using four M4 x 10mm Phillips screws (E) on each bracket.
Installation Instructions YSM2 END VIEW 2 Speaker Engage top slot over top screw Wall Bracket (A) Engage lower slot over lower screw 3 (YP-1000 Speaker Shown) Figure 11 9
YSM2 Installation Instructions USA/International Europe Asia Pacific 8800-000064 2007 Chief Manufacturing www.chiefmfg.com 05/07 A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.6918 Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands +31 (0)40 2668620 +31 (0)40 2668615 Room 30I, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA.
