Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface Warning Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standards could void your authority to operate the equipment. If your purchase option includes both Wireless LAN and 3.5G modules, then the appropriate antennas will be installed.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place it on an unstable surface. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company. • The power adapter may have either a 2-prong or a 3-prong grounded plug.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface XIV
Preface Contents Notice .................................................................................I FCC Statement .............................................................II Instructions for Care and Operation ........................... V Power Safety .............................................................VII Battery Precautions ................................................. VIII Cleaning ..................................................................... IX Servicing ...............
Preface Audio Features ...............................................................2-9 Tablet PC Options ........................................................2-10 Adding a Printer ...........................................................2-15 USB Printer ..............................................................2-15 Parallel Printer ..........................................................2-15 Power Management Overview ........................................................................
Preface Fingerprint Reader Module ........................................4-7 3.5G Module ...............................................................4-7 Intel Turbo Memory Technology Driver ....................4-7 BIOS Utilities Overview ........................................................................5-1 The Power-On Self Test (POST) ...................................5-2 Failing the POST .........................................................5-3 Fatal Errors .................................
Preface Intel WLAN Driver Installation .................................7-7 PC Camera Module ......................................................7-12 PC Camera Driver Installation .................................7-13 Fingerprint Reader Module ..........................................7-20 User Enrollment ........................................................7-21 3.5G Module ................................................................7-24 3G Watcher Application ......................................
Preface Power ............................................................................ C-4 Battery ........................................................................... C-4 Environmental Spec ...................................................... C-5 Dimensions ................................................................... C-5 & Weight ...................................................................... C-5 Optional ........................................................................
Preface XX
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 • Chapter 3 • Chapter 4 • Chapter 5 • Chapter 6 • Chapter 7 • Chapter 8 • Appendix A • Appendix B • Appendix C • Appendix D A guide to using some of the main features of the computer e.g.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the remainder of this User’s Manual. You may also find the notes marked with a of interest to you.
Quick Start Guide Not Included Operating Systems (e.g. Windows Vista/Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in Table 4 - 1, on page 4 - 3. Drivers are programs which act as an interface between the computer and a hardware component e.g.
1 Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the following operating systems are supported.
Quick Start Guide System Startup 1. 2. 3. 4. 5. 6. Remove all packing materials and place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
1 Quick Start Guide Rotating The LCD Panel You can use the computer either in Notebook Mode, or in Tablet Mode. To put the computer into Tablet Mode: 1. 2. 3. 4. 5. Raise the lid/LCD panel 1 . Carefully rotate the lid/LCD panel fully in the (clockwise) direction indicated by the arrow 2 , until it is unable to rotate any further 3 . Carefully push the lid/LCD panel down into Tablet Mode 4 , and use the stylus pen as an input device 5 .
Quick Start Guide Tablet PC Input Use the stylus pen provided to interact with the computer in the same way you would use the mouse (use the stylus pen to tap/double-tap on-screen buttons etc.). Calibrate the touch screen before using the stylus pen (make sure you have installed the Touch Screen driver - see “Touch Panel” on page 4 - 5). Calibrating the Touch Screen 1. 2. 3.
1 Quick Start Guide 4. 5. Use the stylus pen to touch the blinking symbol until you hear a beep or the symbol stops blinking (maintain contact until the symbol stops blinking). The plus (+) symbol will change from green to white after the reading has been obtained. Touch Panel Input Device Do not use any sharp or pointed objects as your input device e.g. the end of a pen or pencil. You should only use the provided stylus pen (PDA type) as your input device.
Quick Start Guide Stylus Pen Input Configure the stylus pen input settings from the Pen and Input Devices control panel in Windows Vista. Access the control panel as follows: 1. 2. 3. 4. 5. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Mobile PC and double-click Pen and Input Devices (or just double-click Pen and Input Devices ). Click Touch (tab). If you wish to use your finger as an input device you can enable this from this control panel tab.
1 Quick Start Guide Tablet PC Input Panel When not in use the Tablet PC Input Panel (not available in Windows Vista Home Basic Edition) docks at the side of the screen (and may be docked at either side of the screen at any height) with just a small portion visible. Move the pen over the TIC and then tap it to activate it. The input panel allows you to input text without the use of a keyboard.
Quick Start Guide System Map: LCD Panel Open 1 Figure 1 - 7 LCD Panel Open Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 1. 2 3 4 5 Use the function key combinations/On-Screen Menu buttons to toggle power to the 3.
1 Quick Start Guide LED Indicators The two sets of LED indicators (LED Status Indicators and LED Power & Communication Indicators) on the computer display helpful information about the current status of the computer.
Quick Start Guide Keyboard The keyboard has a numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly (see Figure 1 - 8). See Table 1 - 4, on page 1 - 14 for details of the function/ hot key indicators. Function Keys NumLk & ScrLk Keys Play/Pause Key Numerical Keypad 3.5G Module Power Toggle Key Fn Key Special Characters Some software applications allow the number-keys to be used with Alt to produce special characters.
1 Quick Start Guide Function Keys & Visual Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators (see the table below) are available when the Pop Menu driver is installed (see “Pop Menu Utility” on page 4 - 6). Keys Function/Visual Indicators Keys Function/Visual Indicators Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F7 Display Toggle Fn + _ Fn + F1 Fn + F2 Fn + F3 3.
Quick Start Guide On-Screen Menu Pressing the Menu button on the computer will bring up the On-Screen Menu buttons (make sure you install the pop menu driver - see “Pop Menu” on page 4 - 5). Use the stylus pen to touch any of the buttons to activate the control. If the PC Camera (optional), Bluetooth (optional), WLAN (optional) or 3.5G (optional) modules are on the indicator will appear green ; if the modules are off then the indicator will appear black .
1 Quick Start Guide System Map: Front & Rear Views Figure 1 - 9 Front & Rear Views LED Power & Communication Indicators 2. Power Switch 3. S/PDIF-Out Jack 4. Microphone-In Jack 5. Headphone-Out Jack 6. 7-in-1 Card Reader 7. Stylus Pen Holder 8. Security Lock Slot 9. 2 * USB 2.0 Ports 10. DC-In Jack 11. Battery 1 2 1.
Quick Start Guide System Map: Left & Right Views Figure 1 - 10 Left & Right Views 2 1 6 3 7 4 5 9 8 Mini-IEEE 1394 Port The Mini-IEEE 1394 port only supports SELF POWERED IEEE 1394 devices. 1. 2. 3. 4. 5. 6. 7. Overheating To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s) while the computer is in use. 8. 9. Stylus Pen Holder Optical Device Drive Bay (for CD/ DVD Device - see page 2 - 3) 1 * USB 2.
1 Quick Start Guide Disk Eject Warning Changing DVD Regional Codes Don’t try to eject a CD/DVD while the system is accessing it. This may cause the system to “crash”. Stop the disk first then eject it, or press the stop button twice. Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives.
Quick Start Guide System Map: Bottom View 1 CPU The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. Figure 1 - 11 Bottom View 2 1. 2. 3 4 3. Overheating To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use. 4. 4 Battery Hard Disk Bay Cover (3.
1 Quick Start Guide Windows Vista Start Menu & Control Panel Most of the control panels, utilities and programs within Windows Vista (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display Settings control panel (in Personalization) in Windows Vista as long as the appropriate Intel video driver is installed. For more detailed video information see “Intel Video Driver Controls” on page B - 1. To access Display Settings in Windows Vista: 1. 2. 3. 4. 5. 6. 7. Click Start, and click Control Panel (or point to Settings and click Control Panel).
1 Quick Start Guide 1 4 2 3 Figure 1 - 13 - Display Properties Desktop Intel Display Mode Description Single Mode One of the connected displays is used as the display device Intel(R) Dual Display Clone Mode Both connected displays output the same view and may be configured independently Extended Desktop Mode Both connected displays are treated as separate devices, and act as a virtual desktop Table 1 - 6 - Display Options 1 - 22 Video Features
Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 20) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
1 Quick Start Guide 1 - 24
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • • • Hard Disk Drive Optical (CD/DVD) Device 7-in-1 Card Reader ExpressCard Slot TouchPad and Buttons/Mouse Audio Features Tablet PC Options Adding a Printer Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Figure 2 - 1 Hard Disk Location 2 - 2 Hard Disk Drive Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 14).
Features & Components 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Features & Components DVD Regional Codes 2 To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - 18. .
Features & Components 2 Card Reader Cover Make sure you keep the rubber cover provided in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. 7-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the Card Reader driver (see “CardReader” on page 4 - 5).
Features & Components ExpressCard Slot The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards). Make sure you install the Card Reader driver (see “CardReader” on page 4 - 5). ExpressCard/54 is used for applications which require a larger interface slot, e.g. CompactFlash card reader. The number denotes the card width; 54mm for the Express Card/54 and 34mm for the ExpressCard/34.
Features & Components 2 Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details. TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.
Features & Components Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/ control panel (right-click the taskbar icon to bring up an audio menu). The volume may also be adjusted by means of the Fn + F5/F6 key combination. Sound Volume Adjustment The sound volume level is set using the volume control within Windows (and the volume function keys on the computer).
Features & Components 2 Windows Vista Home Basic Edition Note that certain features such as Screen Orientation, Flicks and Handwriting Recognition are not available in Windows Vista Home Basic Edition. Tablet PC Options Chapter 1 contains information on rotating the screen into Tablet mode (see “Rotating The LCD Panel” on page 1 - 6), Tablet PC input (see “Tablet PC Input” on page 1 - 7) and the On-Screen Menu functions (see “On-Screen Menu” on page 1 - 15).
Features & Components Flicks Flicks are quick gestures that can be assigned various actions (similar to quickly drawing a line in one of eight directions). It is important that the motion is straight and quick. Configure flicks from the Pen and Input Devices control panel (see page 1 - 9). You can enable navigational flicks (default), editing flicks or customize your own To customize flicks, click on the drop down menu next to one of the actions and select Add.
Features & Components 2 Handwriting Recognition Help Open the Tablet PC Settings control panel (see page 1 - 10) and click the Handwriting Recognition tab. Handwriting Recognition You can teach the computer to recognize your handwriting in order to help to minimize data entry errors when using the writing or character pads. 1. 2. 3. 4. Click on Learn more about handwriting personalization to bring up the help menu.
Features & Components Other Useful Windows Vista Features for Tablet PC Users 2 Multi-Select Files in Windows Explorer The option to multi-select files in Windows Explorer in Windows Vista is very useful when using a pen as your input device. 1. 2. 3. 4. 5. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Appearance and Personalization and click Folder Options (or just double-click Folder Options).
Features & Components 2 Internet Explorer Panning Hand Tool Internet Explorer has a Panning Hand tool that allows easier navigation of Internet webpages. Simply click the Panning Hand icon in the Command Bar to activate the tool. The hand icon will appear to allow you to pan around the webpage, however the icon will change to a pointed finger icon when you move across a link.
Features & Components Adding a Printer The most commonly used peripheral is a printer. The following conventions will help you to add a printer; however it is always best to refer to the printer manual for specific instructions and configuration options. USB Printer Most current printers have a USB interface connection. You may use any one of the ports to connect the printer. Install Instructions: 1. 2. 3. 4. 5.
Features & Components 2 2 - 16
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. 3 AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-in jack at the rear of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle.
Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on slide the power switch on the front panel to the left and release it. When the computer is on, you can use the power switch as a Sleep/Hibernate hotkey button when you slide it to the left and release it in less than 4 seconds (sliding and holding the power switch to the left without releasing it for longer than this will force the computer to shut down).
Power Management 3 Resuming Operation See Table 3 - 1, on page 3 - 9 for information on how to resume from a power-saving state. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 1 Power Plan Advanced Settings 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance for maximum performance when the computer is powered from an AC power source.
Power Management 3 Power Button The Power Button in the Start Menu (in Classic View use the Shut Down button ) can be used to send the computer into a power-saving state. Sleep Mode & Mobile PC Battery A mobile PC in Sleep uses very little battery power. After an extended period of time the computer will save any open documents and applications to hard disk. Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management 3 Password Protection Configuring the Power Buttons The power switch (power button)/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. It is recommended that you enable a password on wake up in order to protect your data. However you can disable this setting from the Power Options menu by clicking Require a password on wakeup in the left menu, and selecting the options (click Change settings that are currently unavailable).
Power Management Resuming Operation You can resume operation from power-saving states by sliding the power switch, or in some cases pressing the sleep button (Fn + F4 key combo). Power Status Icon To Resume Color Power Off Off Slide the Power Switch Sleep Blinking Green Slide the Power Switch Closing the Lid If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up.
Power Management 3 Low Battery Warning When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted. Battery Information Please follow these simple guidelines to get the best use out of your battery. Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g.
Power Management Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter. • Reduce the amount of time before the display is turned off. • Close wireless, Bluetooth, modem or communication applications when they are not being used.
Power Management Battery Life 3 Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason see “Removing the Battery” on page 6 - 3. New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page 3 - 14 for instructions on how to do this).
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Caution Danger of explosion if battery is incorrectly replaced. Damaged Battery Warning Should you notice any physical defects (e.g.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 3 1. 2. 3. Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options. Choose the options below (click Yes if a warning appears).
Power Management 3 How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation Insert the Device Drivers & Utilities + User’s Manual CD-ROM and click Install Drivers (button), or Option Drivers (button) to access the optional driver menu. 1. 2. 4 3. Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below.
Drivers & Utilities Driver Name Page # Driver Name Page # Chipset Page 4 - 5 TouchPad Page 4 - 6 Video Page 4 - 5 Pop Menu Utility Page 4 - 6 Touch Panel Page 4 - 5 Wireless LAN Module Page 7 - 7 Audio Page 4 - 5 PC Camera Module Page 7 - 13 Modem Page 4 - 5 Fingerprint Reader Module Page 7 - 20 CardReader Page 4 - 5 3.
Drivers & Utilities 4 Updating/Reinstalling Individual Drivers User Account Control (Win Vista) If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Programs > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer).
Drivers & Utilities Driver Installation Procedure Insert the Device Drivers & Utilities + User’s Manual CD-ROM (WinVista) and click Install Drivers (button), or Option Drivers (button) to access the optional driver menu. Chipset 1. Click 1.Install Chipset Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish. Video 1. Click 2.Install Video Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer. Touch Panel 1. Click 3.Install Touch Panel Driver > Yes. 2.
Drivers & Utilities 4 TouchPad 1. Click 8.Install TouchPad Driver > Yes. 2. Click Next. 3. Click Finish > Restart Now to restart the computer. Pop Menu Utility 1. Click 9.Install POP Menu Utility > Yes. 2. Click Next > Install. 3. Click Finish > Finish to restart the computer. 4. See “On-Screen Menu” on page 1 - 15 for details. Windows Update After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc.
Drivers & Utilities Optional Drivers Fingerprint Reader Module See the pages indicated for the driver installation procedures for any modules included in your purchase option. See the introduction in “Fingerprint Reader Module” on page 7 - 20, and check the installation procedure. 3.5G Module Bluetooth Module Note: The operating system is the default setting for Bluetooth control in Windows Vista, and does not require a driver. See “Bluetooth Module” on page 7 - 2 for configuration instructions.
Drivers & Utilities 4 4 - 8
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Phoenix TrustedCore(tm) Setup Utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup.
BIOS Utilities POST Screen 5 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST Note: The POST screen as pictured right is for guideline purposes only. The POST screen on your computer may appear slightly different. If you disable the Boottime Diagnostic Screen, the POST screen will not appear. The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory).
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities The Setup Program The Phoenix TrustedCore(tm) Setup Utility tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup 5 To enter Setup, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few seconds after you turn on the system. If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu Phoenix TrustedCore(tm) Setup Utility Figure 5 - 2 Main Main Advanced Security Boot Exit Main Menu Item Specific Help System Time: System Date: [22:12:05] [10/30/2007] IDE Primary/Master IDE Secondary/Master [FUJITSU MHW2100BH-(S1)] [Optiarc DVD RW AD-7530B-(] System Memory Extended Memory 640 KB 1014 MB BIOS Revision ******** 5 F1 Esc Help Exit Select Item Select Menu -/+ Enter , , or selects field.
BIOS Utilities IDE Primary/Master (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a HDD on the computer’s Primary/Master IDE Channel. Use the Auto (Type:) setting to have the items configured automatically for you. IDE Secondary/Master (Main Menu) Pressing Enter opens the sub-menu to show the configuration of an optical Device on the computer’s Secondary/Master IDE Channel. Use the Auto (Type:) setting to have the items configured automatically for you.
BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu Phoenix TrustedCore(tm) Setup Utility Advanced Advanced Main Security Boot Exit Item Specific Help Sata Control Sub-Menu 5 Reset Configuration Data: Legacy USB Support: Boot-time Diagnostic Screen: Power On Boot Beep Battery Low Alarm Beep: [No] [Enabled] [Disabled] [Disabled] [Enabled] Total Graphics Memory: Graphics Frequency [128MB] [Power saver mode] F1 Esc Help Exit Select Item Select Menu -/+ Enter Control SATA and PATA
BIOS Utilities Sata Control Sub-Menu > Intel Robson: (Advanced Menu) The sub-menu here allows you to enable/disable support for Intel Turbo Memory, if you have included an Intel Turbo Memory module in your purchase option. You will need to enable this option BEFORE installing the operating system software. (do not enable this option in Windows XP or on a Windows Vista operating system that has been installed without the option enabled). See “Intel Turbo Memory Module” on page 7 - 34 for more details.
BIOS Utilities Reset Configuration Data: (Advanced Menu) This item is set to No as default. You can change the setting to Yes if you have installed a new add-on which has reconfigured the system, resulting in such a serious system conflict that the operating system is unable to boot. Legacy USB Support: (Advanced Menu) Use this menu item to enable/disable the support for Legacy Universal Serial Bus.
BIOS Utilities Total Graphics Memory: (Advanced Menu) Use this menu item to set the amount of system memory to be allocated for use by the internal graphics device. The default memory size allocated is 128MB, and this may be adjusted to 256MB (by pressing the spacebar to adjust) if required.
BIOS Utilities Security Menu Phoenix TrustedCore(tm) Setup Utility Security Menu 5 Main Security Menu 5 - 12 Security Menu Security Security Boot Exit Item Specific Help The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS.
BIOS Utilities Fixed disk boot sector: (Security Menu) If you choose “Write-Protect” this will protect against viruses being written to the hard disk boot sector (this is not a substitute for installing an anti-virus program - see “Viruses” on page 8 - 4). Password on boot: (Security Menu) Specify whether or not a password should be entered to boot the computer (you may only set a password on boot if a supervisor password is enabled).
BIOS Utilities Boot Menu Phoenix TrustedCore(tm) Setup Utility Figure 5 - 6 Main Advanced Security Boot Exit Boot Menu Item Specific Help Boot priority order: 1: IDE CD: Optiarc DVD RW AD-7530B-(S 2: USB FDC: 3: USB KEY: 4: USB HDD: 5: IDE HDD: FUJITSU MHW2100BH-(S1) 6: PCI BEV: Realtek Boot Agent 7: 8: Excluded from boot order: : USB CDROM: : USB ZIP 5 F1 Esc Help Exit Select Item Select Menu -/+ Enter Keys used to view or configure devices: Up and Down arrows select a device.
BIOS Utilities Exit Menu Figure 5 - 7 Phoenix TrustedCore(tm) Setup Utility Main Advanced Security Boot Exit Exit Menu Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Esc Help Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
BIOS Utilities 5 5 - 16
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. 4. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Slide the battery out in the direction of the arrow 3 .
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CD-ROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer 4. 5. 6. Grip the tab and slide the hard disk in the direction of arrow 4 . Lift the hard disk up and out of the computer 5 . Reverse the process to install a new hard disk drive.
Upgrading The Computer Upgrading the Optical (CD/DVD) Device 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery. Locate the RAM & CPU bay cover and remove screws 1 - 4 . Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. Carefully disconnect the fan cable 5 , and remove the cover 6 . 2 3 6 1 4 5 Figure 6 - 4 Removing the RAM & CPU Bay Cover 6 Fan Cable Make sure you reconnect the fan cable 5 before screwing down the bay cover.
Upgrading The Computer 5. 6. 7. 8. Remove the screw at point 7 , and use a screwdriver to carefully slide out the optical device. Insert the new device and replace the optical device screw 7 . Reconnect the fan cable before replacing the bay cover ( 5 in Figure 6 - 4 on page 6 - 6). Replace the bay cover and screws.
Upgrading The Computer System Memory 6 The computer has two memory sockets for 200 pin Small Outline Dual In-line (SO-DIMM) DDRII (DDR2) type memory modules (see “Memory” on page C 2 for details of supported module types). Upgrading the System Memory (RAM) 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery. Locate the RAM & CPU bay cover and remove screws 1 - 4 . Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover.
Upgrading The Computer 5. 6. 7. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 7 & 8 ) in Figure 6 - 7. The RAM module will 9 pop-up, and you can remove it. Pull the latches to release the second module if necessary. 7 Contact Warning Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance.
Upgrading The Computer 8. .Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. 9. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit without much pressure. 10. Press the module in and down towards the mainboard until the slot levers click into place to secure the module. 6 Figure 6 - 8 RAM Module Insertion 11.
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. • • • • • • Bluetooth Module Wireless LAN Module PC Camera Module Fingerprint Reader Module 3.
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Bluetooth Module The operating system’s Bluetooth Devices control panel is used to configure the Bluetooth settings in Windows Vista, and therefore does not require a driver.
Modules & Options Bluetooth Configuration in Windows Vista Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). To Turn the Bluetooth Module On 1. 2. 3. Press the Fn + F12 key combination to power on the Bluetooth module. A Bluetooth icon will appear in the taskbar (see sidebar).
Modules & Options To Add a Bluetooth Device 1. 2. Figure 7 - 2 Add Bluetooth Device Wizard 3. 4. 5. Access the Bluetooth Devices control panel. Click Options (tab), and make sure that Allow Bluetooth devices to connect to this computer check box (Connections) has a tick inside it. Click Devices (tab), and then click Add. The Add Bluetooth Device Wizard will appear. Click to select “My device is set up and ready to be found”, and then click Next. 6. 7. 8.
Modules & Options To Change Settings for the Bluetooth Device 1. 2. Access the Bluetooth Devices control panel. Click on the device you want to change and click Properties to: • • Change the name of the device (click General, type a new name and click OK). Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK). To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3. Access the Bluetooth Devices control panel.
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + F11 key combination/On-Screen Menu button to toggle power to the WLAN module, and check the indicator to see if the module is powered on or not (see Table 1 - 4, on page 1 - 14/ Table 1 - 5, on page 1 - 15/ Table 1 - 3, on page 1 - 12).
Modules & Options 802.11 b/g WLAN Driver Installation 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual CD-ROM (WinVista) into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install WLan driver > Yes. 4. Choose the language you prefer and click Next. 5. Click Next > Install. 6. Click Finish to complete the installation. 7. The operating system is the default setting for Wireless LAN control in Windows Vista (see overleaf).
Modules & Options Connecting to a Wireless Network Make sure the Wireless LAN module is turned on. 1. Click the taskbar wireless icon , and then click Connect to a network (or rightclick the icon , and then click Connect to a network). Figure 7 - 5 Taskbar Menus Click icon Right-click icon 7 Network and Sharing Center 2. 3. In the Show list, click to choose Wireless from the drop-down menu. A list of currently available networks will appear.
Modules & Options 4. 5. Click a network, and then click Connect. If you do not see a network you want to connect to, click Set up a connection or network (a list of options will appear allowing manual searching, and creating a new network). Figure 7 - 7 Connecting 7 6. Move the cursor over the taskbar icon to see the connection status (see below).
Modules & Options 7. Security Enabled Networks To disconnect from the wireless network you can click the taskbar wireless icon , and then select Connect or disconnect to access the network menu, and click Disconnect (or right-click the icon , and then click Disconnect from). You should try to make sure that any network you are connecting to is a secure network. 7 Click icon Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Modules & Options Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center: 1. 2. 3. Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Windows Mobility Center (Mobile PC). Click the button to Turn wireless off/on, or click the icon to access the network menu.
Modules & Options Latest PC Camera Driver Information 7 Check the CD, and any accompanying insert pages, for the latest updated information on the PC Camera driver, which may override the information provided here. PC Camera Module There are 2 camera options available for this computer, depending on your purchase configuration. The 1.3M pixel camera module uses the BisonCap application to capture video files, and the 2.0M pixel camera module uses the VideoView application to capture video files.
Modules & Options PC Camera Driver Installation 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual CD-ROM (WinVista) into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 2.PC Camera, Web cam > Yes. For the 1.3M Pixel Camera Module: 1. Choose the language you prefer and click Next > Next. 2. Click Finish to restart the computer. 3.
Modules & Options PC Camera Audio Setup (all camera modules) If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 7 Click Start, and click Control Panel (or point to Settings and click Control Panel). 2. Click Sound (Hardware and Sound). 3. Click Recording (tab). 4. Right-click Microphone (Realtek High Definition Audio) and make sure the item is not disabled. 5. Double-click Microphone (or select Properties from the right-click menu).
Modules & Options Figure 7 - 11 Audio Setup for PC Camera Right-click 7 PC Camera Module 7 - 15
Modules & Options Pre-Allocating File Space You may pre-allocate the file size (File > Allocate File Size) for the capture file in the BisonCap/VideoView program. 7 Pre-allocating space on the hard disk can improve the capture quality (particularly of large capture files), by reducing the amount of work the hard disk has to do in finding space for the video data as it is being captured. See also “Reducing Video File Size” on page 7 - 17. BisonCap (1.3M Cam)/VideoView (2.
Modules & Options Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Modules & Options Eliminating Screen Flicker If you find that the video screen in the BisonCap/VideoView program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. Run the BisonCap/VideoView program. Go to Options and scroll down to select Video Capture Filter.... For Bison Cap: 3. Click either 50Hz or 60Hz under Frequency in Property Page (tab). For VideoView: 4. Click either 50Hz or 60Hz under Flickering Reduction in Image (tab).
Modules & Options Zoom The BisonCap and VideoView programs allow you to zoom the camera in and out. 1. Run the BisonCap/Video View program. For Bison Cap: 2. Go to Zoom and select Zoom Out/Zoom In. For Video View: 3. Go to Options and scroll down to select Setting (Use the slider to adjust the zoom level, and click OK to save the setting). Bison Cap VideoView Figure 7 - 13 Zoom/Setting Snapshot Folder The Snapshot folder’s default location is on the desktop.
Modules & Options Fingerprint Reader Module If you have included the fingerprint reader in your purchase option you will need to install the driver as per the instructions below. Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full security protection. Before beginning the enrollment process it is recommended that you go through the fingerprint tutorial.
Modules & Options User Enrollment 1. 2. 3. Click Start > Programs/All Programs > Protector Suite QL > User Enrollment, or double click the taskbar icon . On the first run of the program you will be asked to click the button to accept the license, and then click OK. Click Next and select “Enrollment to the hard disk”, and click Finish. Figure 7 - 14 Enroll to Hard Disk 4. 5. 6. 7. 8.
Modules & Options 9. Fingerprint Enrollment Note that it is strongly recommended that you enroll more than one finger in case of injury etc. 10. 11. 12. 13. 14. Click the button above any of the fingers to begin the enrollment process for that finger. Swipe the finger three times to enroll that finger. Repeat the process for all the fingers you wish to enroll (see sidebar), and then click Next. Click Finish. Click any of the headings under “Learn more about:” to get more information on any topic.
Modules & Options the Control Center etc. from the Protector Suite QL item in the Programs/All Programs menu. Help & Manual Right-click the taskbar icon to bring up the menu to select Help. Help may also be accessed from the Fingerprint Control Center. 7 Figure 7 - 16 Control Center & Biomenu 17. See “Help & Manual” for further details. 18.
Modules & Options Power Safety Warning 7 Before you undertake any installation procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. 3.5G Module If you have included an optional 3.
Modules & Options 5. 6. Insert the USIM card as you would into your mobile phone. Slide the SIMLOCK in the direction of the arrow 5 (Figure 7 - 18) in order to release the lock and lift it up. Figure 7 - 18 SIMLOCK Unlock 5 7 7. Insert the USIM card as illustrated in (Figure 7 - 19) and close the SIMLOCK. Figure 7 - 19 Insert the USIM Card 3.
Modules & Options 8. Close the SIMLOCK by pushing it in the direction of the arrow in Figure 7 - 20. 9. The 3.5G module 6 is pictured on the left, and the installed USIM card 7 on the right in Figure 7 - 21. Figure 7 - 20 SIMLOCK Lock 7 Figure 7 - 21 Module and USIM Card Location 6 7 10. Replace the hard disk assembly, cover, screws and battery etc. 7 - 26 3.
Modules & Options 3G Watcher Application With the 3.5G module and USIM card (provided by your service provider) installed you may then install the 3G Watcher application. The 3G Watcher application allows you to directly access your 3.5G internet service from the computer. 3G Watcher Application Installation 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual CD-ROM (WinVista) into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 4.
Modules & Options Setting Up a Carrier Profile Although the connection information is stored on the USIM card supplied by the service provider, you will need to set up the appropriate carrier profile from the 3G Watcher software. 1. 2. 3. 4. 7 Figure 7 - 22 Add WWAN Profile 7 - 28 3.5G Module Power on the 3.5G module using the Fn + _( ) key combination (the icon will be green).
Modules & Options 5. 6. 7. You can then enter a new profile name or choose a profile from the drop-down list provided by the software (see the sidebar for information on the profile details). Figure 7 - 23 Profile Information User Options Click General and/or Advanced (and the submenus under Advanced) in the left menu, and then click in any of the fields to add the appropriate information supplied by your service provider. Click Apply > OK to save the information.
Modules & Options Connecting to the Service Provider 1. 2. Figure 7 - 25 3. 3G Watcher Power on the 3.5G module using the Fn + _( ) key combination (the icon will be green). You can access the 3G Watcher application from the Start menu (Start > Programs/All Programs > Sierra Wireless > 3G Watcher), or by clicking the desktop icon . The software will run and display the service provider name (connection information is obtained from the USIM card).
Modules & Options 6. When the connection is successful a taskbar notification will appear (as below). Figure 7 - 27 Connected Taskbar Notification 7. 8. 9. You can then access the internet, download e-mail etc. as per any internet connection. While you are connected the taskbar icon will be green (it will be red when the program is running but not connected). To disconnect click the Disconnect icon. 7 Figure 7 - 28 3GWatcher Connected 10. The program will disconnect from the service provider. 11.
Modules & Options 12. If you click the 3G Watcher close icon to click OK to confirm the program exit. a message will be displayed asking you Figure 7 - 29 Exit Warning 13. Exiting the program DOES NOT turn off the 3.5G module, and you will need to press the Fn + _( ) key combination to turn off the module (pay careful attention to this aboard aircraft - see “Wireless Device Operation Aboard Aircraft” on page 7 - 27). 14.
Modules & Options Short Messaging Service In addition to standard internet services you may also send and receive SMS text messages using the 3G Watcher program. Reading SMS Messages 1. 2. 3. 4. The SMS message indicator in the main window will notify you of any new messages received. Double-click the icon or select Tools > SMS Express. Select the inbox folder and select any message to read it.
Modules & Options Intel Turbo Memory Module If you have included an Intel Turbo Memory (Robson) NAND flash memory card module in your purchase option, then you will need to enable the option in the BIOS (see “Advanced Menu” on page 5 - 8) BEFORE installing the Windows Vista operating system software (do not enable this option in Windows XP or on a Windows Vista operating system that has been installed without the option enabled).
Modules & Options Intel Turbo Memory Setup 1. 2. 3. 4. 5. 6. Start-up your notebook computer and press to enter the BIOS. Use the arrow keys to select the Advanced menu heading. Use the arrow keys to select (highlight in white) the Sata Control Sub-Menu, and press . Press to access the dialog box and use the arrow keys to select Enhanced, and then press again. Use the arrow keys to select DFOROM (Robson) Support and press .
Modules & Options 9. ReadyBoost & ReadyDrive Note that enabling ReadyBoost & ReadyDrive from the Intel® Turbo Memory Console will depend on which Turbo Memory module is installed: 7 If you have a 1GB Turbo Memory module installed you may enable both ReadyBoost & ReadyDrive. If you have a 512MB Turbo Memory module installed you may enable ReadyDrive ONLY. Press to bring up the Setup Configuration menu and press to save the changes and exit the BIOS and reboot the computer. 10.
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “LED Indicators” on page 1 - 12) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED power indicator , is blinking orange. Low Battery. Plug in the DC power source.
Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 19). Make sure you’re using the correct adapter.
Troubleshooting Problem You forget password. the Possible Cause - Solution boot If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Problem Unwelcome numbers appear when typing. Possible Cause - Solution If the LED is lit, then Num Lock is turned ON (see “LED Indicators” on page 1 - 12). Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work. 8 The system freezes or the screen goes dark.
Troubleshooting Problem Possible Cause - Solution The PC Camera module cannot be detected. The module is off. Press the Fn + F10 key combination, or On-Screen Menu button, in order to enable the module (see “Function Keys & Visual Indicators” on page 1 - 14). Run the camera program to view the camera picture. The Wireless LAN/ PC Camera/3.5G modules cannot be configured. The driver(s) for the module(s) have not been installed.
Troubleshooting 8 8 - 12
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer. External Monitor (VGA) Port This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD.
Interface (Ports & Jacks) Item RJ-45 LAN Jack Description This port supports LAN (Network) functions. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port. Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. S/PDIF-Out Jack This S/PDIF (Sony/Philips Digital Interface Format) Out Jack allows you to connect your DVDcapable PC to a Dolby AC-3 compatible receiver for “5.1” or ‘dts’ surround sound.
Interface (Ports & Jacks) A A - 4
Intel Video Driver Controls Appendix B: Intel Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 16. Intel Video Driver Installation DVMT Notes Make sure you install all the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Video 1. Insert the Device Drivers & Utilities + User’s Manual CD-ROM (Win Vista) into the CD/DVD drive. 2. Click Install Drivers. 3. Click 2.Install Video Driver > Yes. 4. Click Next > Yes > Next > Next. 5.
Intel Video Driver Controls Taskbar Icon The Intel GMA control panel can also be accessed by clicking the icon in the taskbar and selecting Graphics Properties from the menu. Intel Graphics Properties More advanced video configuration options are provided by the Intel(R) Graphics Media Accelerator Driver for Mobile. 1. 2. Open the Display Settings control panel (see “Video Features” on page 1 - 16) and click Advanced Settings (button). Click the Intel(R)... tab and click Graphics Properties (button).
Intel Video Driver Controls You may make changes to the devices, color, schemes, Hot Keys etc. by clicking the appropriate menu item or button. Click Information (button) to obtain useful information about the graphics properties of the computer, and see the Support tab in Information to get weblinks to the latest information on the Intel Website. Help Menus Right-click on many of the items in the tabs to bring up the “What’s This?” button. Click the “What’s This?” button to bring up the help menu.
Intel Video Driver Controls Application.exe You will need to locate the actual application executable (.exe) file, not just the shortcut. To find the application rightclick its shortcut on the desktop click Properties. Click the Shortcut (tab) and see where the executable file is located by clicking the Find Target (button). Note the location and you will then be able to browse to this file.
Intel Video Driver Controls Attaching Other Displays Besides the built-in LCD, you can also use an external monitor/flat panel display, connected to the external monitor port at the rear of the computer, as your display device. The following are the display options: 1. 2. The built-in LCD OR an external monitor/flat panel display connected to the external monitor port (Single Display). The built-in LCD AND an external monitor/flat panel display connected to the external monitor port (Multiple Display).
Intel Video Driver Controls Configuring from Intel® GMA Driver for Mobile 1. Multiple Display 2. 3. At least one other display must be attached in order to view Multiple Display options. Go to the Intel Graphics Properties control panel (see “Intel Graphics Properties” on page B - 2) and click Display Devices. Click to choose the display option from the Multiple Display menu. Click Apply (and OK to confirm the settings change) and OK (button).
Intel Video Driver Controls Display Modes Single Display Only one of your attached displays is used. Intel(R) Dual Display Clone (mirrored) This mode will drive multiple displays with the same content. Each device may be configured independently for different resolutions, refresh rates, color quality etc. Use this feature to display the screen through a projector for a presentation. Extended Desktop (extended) This mode allows a desktop to span multiple displays and acts as a large workspace.
Intel Video Driver Controls To Enable Intel(R) Dual Display Clone 1. 2. 3. 4. 5. Figure B - 6 Display Devices & Settings B B - 8 Display Modes Attach your external monitor to the external monitor port, and turn it on. Go to the Intel Graphics Properties control panel (see “Intel Graphics Properties” on page B - 2) and click Display Devices. Click to choose Intel(R) Dual Display Clone (Multiple Display). Click Apply, and OK to confirm the settings change.
Intel Video Driver Controls To Enable Extended Desktop 1. 2. 3. 4. 5. Attach your external monitor to the external monitor port, and turn it on. Go to the Intel Graphics Properties control panel (see “Intel Graphics Properties” on page B - 2) and click Display Devices. Click to choose Extended Desktop (Multiple Display). Click Apply, and OK to confirm the settings change. Click Display Settings to adjust the settings for the attached devices.
Intel Video Driver Controls Using Windows Vista to Enable Extended Mode Display Settings Extended Desktop Use the control panel to drag the monitors to match the physical arrangement you wish to use. 1. 2. 3. 4. 5. You can drag any icons or windows across to either display desktop, which makes it possible to have one program visible in one of the displays, and a different program visible in the other display.
Intel Video Driver Controls Using Display Settings to Enable Extended Mode 1. 2. 3. Attach your external display to the external monitor port, and turn it on. Open the Display Settings control panel (see “Video Features” on page 1 - 16). Click the monitor icon (e.g. 2 ), and make sure you have checked “Extend my Windows desktop onto this monitor.” and click Apply. Click the appropriate monitor icon (e.g. 2 ) to be able to select the option to extend the desktop on to it.
Intel Video Driver Controls B B - 12
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, delayed or updated due to the manufacturer's release schedule. Check with your service center for details.
Specifications Feature Processor Specification Intel® Core™2 Duo Processor (478-pin) Micro-FC-PGA Package, Socket P T7100/ T7250 65nm (65 Nanometer) Process Technology 2MB On-die L2 Cache & 800MHz FSB 1.8/ 2.0 GHz Intel® Core™2 Duo Processor (478-pin) Micro-FC-PGA Package, Socket P T7300/ T7500/ T7700/ T7800 65nm (65 Nanometer) Process Technology 4MB On-die L2 Cache & 800MHz FSB 2.0/ 2.2/ 2.4/ 2.
Specifications Feature Specification Security Security (Kensington® Type) Lock Slot Fingerprint ID Reader Module (Factory Option) BIOS Password BIOS One 8Mb SPI Flash ROM Phoenix™ BIOS Storage One Changeable 12.7mm(h) Optical Device (CD/DVD) Type Drive (see “Optional” on page C - 5) Easy Changeable 2.5" 9.
Specifications Feature Specification Card SlotS One ExpressCard/34(54) Slot One MiniCard Slot Supporting USB and PCIe Interfaces Second MiniCard Slot Supporting USB and PCIe Interfaces (Factory Option) Communication 1000/100/ 10 Mb Fast Ethernet LAN Azalia 56K Plug and Play Fax Modem V.90 & V.92 Compliant *Note: The 3.5G and Intel Turbo Memory Modules cannot coexist. If one of these factory options is included in your purchase option, then the other is unavailable. Wireless LAN Module Options: 802.
Specifications Feature Specification Environmental Spec Temperature Operating: Non-Operating: Dimensions & Weight 306mm (w) * 224mm (d) * 35 - 37.5mm (h) 2.1 kg With 4 Cell Battery and ODD Optional Optical Drive Module Options: DVD/CD-RW Combo Drive Module Super Multi Drive Module Bluetooth 2.0 + EDR (Enhanced Data Rate) Module (Factory Option) *Note: The 3.5G and Intel Turbo Memory Modules cannot coexist.
Specifications C C - 6
Windows XP Information Appendix D: Windows XP Information This Appendix contains information (including control panel information, driver installation etc.) for users of the Windows XP OS.
Windows XP Information Screen Rotation & Re-Calibration Note that you should recalibrate the touch screen after you have rotated the screen to display in a different mode from that first calibrated. Tablet PC Features Windows XP supports limited Tablet PC functions. See “Rotating The LCD Panel” on page 1 - 6 for information on how to put the computer into Tablet PC mode. Make sure you install the Touch Panel driver (see “TouchPanel” on page D - 35).
Windows XP Information 3. 4. Use the stylus pen to touch the blinking symbol until you hear a beep or the symbol stops blinking (maintain contact until the symbol stops blinking). The plus (+) symbol will change from green to white after the reading has been obtained. Touch Panel Input Device Do not use any sharp or pointed objects as your input device e.g. the end of a pen or pencil. You should only use the provided stylus pen (PDA type) as your input device.
Windows XP Information Mouse Options Make sure you have enabled right button emulation to allow the stylus pen to act as a right mouse button to right-click objects on-screen. Use the slide to adjust the cursor stability (Enhance Cursor Stability) to your preference. Tap on Mouse Mode to toggle through the different options for the stylus pen when selecting and dragging objects on-screen. Normal mode most effectively replicates a conventional mouse action.
Windows XP Information On-Screen Menu Pressing the Menu button on the computer will bring up the On-Screen Menu buttons (make sure you install the pop menu driver - see “Pop Menu” on page D - 36). Use the stylus pen to touch any of the buttons to activate the control. If the PC Camera (optional), Bluetooth (optional), WLAN (optional) or 3.5G (optional) modules are on the indicator will appear green ; if the modules are off then the indicator will appear black .
Windows XP Information DVD Regional Codes Changing DVD Regional Codes Go to the Control Panel and double-click System > Hardware (tab), click Device Manager, then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialogue box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code. DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times.
Windows XP Information Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can customize the look of the Start menu by right-clicking the Start menu and selecting Properties from the menu.
Windows XP Information TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. Once you have installed the TouchPad driver (see “TouchPad” on page D - 36) you can configure the functions by double-clicking the TouchPad driver icon on the taskbar.
Windows XP Information Function Keys & Visual Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators (see the table below) are available when the Pop Menu driver is installed (see “Pop Menu” on page D - 36).
Windows XP Information Audio Features You can configure the audio options on your computer from the Sounds and Audio Devices Windows control panel, or from the Realtek HD Audio Manager icon in the taskbar/control panel (this will bring up the Realtek Audio Configuration menus). The volume may also be adjusted by means of the Fn + F5/F6 key combination.
Windows XP Information Video Features You can switch display devices, and configure display options, from the Display Properties control panel in Windows as long as the appropriate Intel video driver is installed. To access Display Properties in Windows: 1. 2. 3. 4. 5. 6. 7. Click Start, point to Settings and click Control Panel (or just click Control Panel). Double-click Display (icon) - In the Appearances and Themes category. Click Settings (tab) in the Display Properties dialog box.
Windows XP Information Display & Graphics Properties Taskbar Icon Besides the built-in LCD, you can also use an external VGA monitor (CRT) or external Flat Panel Display connected to the external monitor port as your display device. You can also access the controller properties from the taskbar. Click on the icon to bring up the menu and scroll to Graphics Properties.
Windows XP Information You may make changes to the devices, color, schemes, Hot Keys etc. by clicking the appropriate menu item or button (also see “Information” on page D - 20). Help Menus Right-click on many of the items in the tabs to bring up the “What’s This?” button. Click the “What’s This?” button to bring up the help menu. Multiple Display At least one other display must be attached in order to view Multiple Display options.
Windows XP Information Application.exe You will need to locate the actual application executable (.exe) file, not just the shortcut. To find the application rightclick its shortcut on the desktop click Properties. Click the Shortcut (tab) and see where the executable file is located by clicking the Find Target (button). Note the location and you will then be able to browse to this file.
Windows XP Information Attaching Other Displays Besides the built-in LCD, you can also use an external monitor/flat panel display as a display device. The following are the display options: 1. 2. The built-in LCD OR an external monitor/flat panel display connected to the external monitor port (Single Display). The built-in LCD AND an external monitor/flat panel display connected to the external monitor port (Multiple Display).
Windows XP Information Function Key Combination You can use the Fn + F7 key combination to toggle through the display options: • Notebook Only • External Display Only • Notebook + External Display Make sure you give the displays enough time to refresh. Display Modes Single Display Only one of your attached displays is used. Intel(R) Dual Display Clone This mode will drive multiple displays with the same content.
Windows XP Information To Enable Intel(R) Dual Display Clone Mode 1. 2. 3. 4. 5. Attach your external display to the external monitor port and turn it on. Open the Intel(R) GMA Driver for Mobile control panel. Click to choose Intel(R) Dual Display Clone from Display Devices (tab). Click Apply, and OK to confirm the settings change. Click Display Settings to adjust the settings for the attached devices.
Windows XP Information To Enable Extended Desktop Mode: Display Settings Extended Desktop You can have different Colors, Screen Area and Monitor Refresh Rates for each display device provided your monitor can support them. 1. 2. 3. 4. 5. Click the appropriate monitor icon and drag it to match the physical arrangement you wish to use (e.g. the secondary display may be extended left/right/above/below the primary display). You can drag the monitor icons to match the physical layout of your displays.
Windows XP Information To Enable Extended Desktop (Display Properties) 1. 2. 3. 4. 5. Attach your external monitor to the external monitor port and turn it on. Click Start, point to Settings (or click Control Panel) and click Control Panel (if you are in Category View choose Appearance and Themes). Double-click Display (icon). In the Display Properties dialog box, click Settings (tab). Click the monitor icon (e.g. 2 ), and make sure you have checked “Extend my Windows desktop onto this monitor.
Windows XP Information Using the GMA Driver to Rotate the Screen In addition to the on-screen menu button and screen rotation button can also use the Intel GMA driver to rotate the screen. , you 1. Click the taskbar icon . 2. Select Graphics Options > Rotation. 3. Click on a chosen screen orientation. Figure D - 15 Graphics Options Rotation Information The Information (button) in the Intel GMA for mobile control panel provides useful information about the graphics properties of the computer.
Windows XP Information Power Management Features To conserve power, especially when using the battery, your computer uses the ACPI power management system. Power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system. The Power Options control panel icon in Windows (see page D - 7) allows you to configure power management features for your computer.
Windows XP Information The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-in jack at the rear of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle.
Windows XP Information Turning on the Computer Now you are ready to begin using your computer. To turn it on slide the power switch on the front panel to the left and release it. When the computer is on, you can use the power switch as a Sleep/Hibernate hot-key button when you slide it to the left and release it in less than 4 seconds (sliding and holding the power switch to the left without releasing it for longer than this will force the computer to shut down).
Windows XP Information Resuming Operation Press a key on the keyboard, or move the mouse/TouchPad to resume from Monitor or Hard Disk Stand by. Power Schemes You can set your computer to conserve power through individual components by means of Power Schemes.
Windows XP Information Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source.
Windows XP Information System Power Options You can use the system power options to stop the computer’s operation and restart where you left off. This system features Stand by and Hibernate sleep mode levels (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - see “Hibernate” on page D - 27). Hibernate Mode vs. Shutdown Hibernate mode and Shutdown are the same in that the system is off and you need to press the power button to turn it on.
Windows XP Information Stand by Stand by saves the least amount of power, but takes the shortest time to return to full operation. During Stand by the hard disk is turned off, and the CPU is made to idle at its slowest speed. All open applications are retained in memory. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Stand by mode to save power.
Windows XP Information Sleep Button You may also configure the Sleep/Resume key combination (Fn + F4) from the menu illustrated. In Windows this is referred to as the Sleep button. Configuring the Power Button The power button may be set to send the computer in to either Stand by or Hibernate mode. In Stand by mode, the LED will blink green. In Hibernate mode the LED will be off (battery) or orange (AC/DC adapter). If you are in a power saving mode set to save power through individual components (e.g.
Windows XP Information Battery Information Please follow these simple guidelines to get the best use out of your battery. Low Battery Warning New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page D - 32 for instructions on how to do this). Battery Life Your computer’s battery life is dependent upon many factors, including the programs you are running, and peripheral devices attached.
Windows XP Information Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you need to remove the battery for any reason, see “Removing the Battery” on page 6 - 3.
Windows XP Information Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center.
Windows XP Information Battery FAQ Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions. How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery.
Windows XP Information Driver Installation Insert the Device Drivers & Utilities + User’s Manual CD-ROM, click Install Drivers/Option Drivers (button) and then click the appropriate driver name from the Drivers Installer menu. Follow the instructions to install the driver. 1. Check the driver installation order from Table D - 4 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below. 2.
Windows XP Information WinXP SP2 Driver Page # Chipset Page D - 35 Video Page D - 35 TouchPanel Page D - 35 Audio Page D - 36 Modem Page D - 36 CardReader Page D - 36 LAN Page D - 36 TouchPad Page D - 36 Pop Menu Page D - 36 Wireless LAN Module Page D - 44 PC Camera Module Page D - 47 Fingerprint Reader Module Page D - 53 3.
Windows XP Information Driver Installation Procedure Windows XP Service Pack 2 Make sure you install Windows XP Service Pack 2 (or a Windows XP version which includes Service Pack 2) before installing any drivers. Service Pack 2 includes support for USB 2.0. If you have upgraded the system by installing Service Pack 2 (i.e. your Windows XP version does not include Service Pack 2) then follow these instructions: 1.Click Start (menu), point to Settings and click Control Panel (or click Control Panel). 2.
Windows XP Information Audio 1. Click 4.Install Audio Driver > Yes. 2. Click Next. 3. Click Finish to restart the computer. CardReader 1. Click 6.Install CardReader Driver > Yes. 2. Click Next > Next. 3. Click Finish to restart the computer. Modem 1. Click 5.Install Modem Driver > Yes. 2. Click OK. 3. The modem is ready for dial-up configuration. LAN 1. Click 7.Install LAN Driver > Yes. 2. Click Next > Install. 3. Click Finish. 4. The network settings can mow be configured.
Windows XP Information Module Drivers 3.5G Module See the following pages for the driver installation procedures for any of the optional modules included in your purchase configuration. See “3.5G Module” on page D - 54. Bluetooth Module Fingerprint Reader Module See “Fingerprint Reader Module” on page D - 53. Note: The operating system is the default setting for Bluetooth control in Windows XP, and does not require a driver. See “Bluetooth Module” on page D 38 for configuration instructions.
Windows XP Information Wireless LAN, Bluetooth & 3.5G Modules Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Bluetooth Module The operating system’s Bluetooth Devices control panel is used to configure the Bluetooth settings in Windows XP, and therefore does not require a driver.
Windows XP Information Bluetooth Local Area Connection Icon If you want to display the Local Area Connection icon for the Bluetooth connection in the taskbar, set it up as follows: 1. 2. 3. 4. Access the Network Connections control panel in Windows (Start > Settings > Network Connections OR Start > Connect To > Show all Connections) or by clicking the taskbar icon . Right-click the Bluetooth connection icon, and select Properties.
Windows XP Information Bluetooth Configuration in Windows XP Bluetooth Taskbar Icon If you cannot see the Bluetooth icon in the taskbar, access the Bluetooth Devices control panel. Click Options (tab), and make sure that Show Bluetooth icon in the notification area check box has a tick inside it. Setup your Bluetooth Device so the Computer Can Find it 1. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. 2. Make the device discoverable (to do this check your device documentation).
Windows XP Information To Add a Bluetooth Device 1. 2. 3. 4. 5. Access the Bluetooth Devices control panel. Click Options (tab), and make sure that Allow Bluetooth devices to connect to this computer check box (Connections) has a tick inside it. Click Devices (tab), and then click Add. The Add Bluetooth Device Wizard will appear. Click to select “My device is set up and ready to be found”, and then click Next. Figure D - 25 Add Bluetooth Device Wizard Passkey Options 6. 7. 8.
Windows XP Information To Change Settings for the Bluetooth Device 1. Access the Bluetooth Devices control panel. 2. Click on the device you want to change and click Properties to: • • Change the name of the device (click General, type a new name and click OK). Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK). To Make your Computer Discoverable to Bluetooth Devices 1. Access the Bluetooth Devices control panel. 2.
Windows XP Information Wireless LAN Module There are 3 Wireless LAN module options available for this computer, depending on your purchase configuration. You may have either an Intel PRO/Wireless 3945ABG (802.11a/b/g) PCIe WLAN module, Intel PRO/Wireless 4965AGN (802.11a/g/n) PCIe WLAN module or 802.11b/g USB WLAN module. Before installing the Wireless LAN driver, make sure that the optional WLAN module is on.
Windows XP Information 802.11 b/g WLAN Driver Installation 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual CD-ROM (WinXP) into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 1.Wireless Lan > Yes. 4. Click Next. 5. Click Finish to complete the installation. 6. The operating system is the default setting for Wireless LAN control in Windows XP (see overleaf). 7.
Windows XP Information Network Connection Use the Windows Network Connections control panel to access available wireless networks (Start > Settings > Network Connections or Start > Connect To > Show all Connections).
Windows XP Information Taking Still Pictures Double-click the My Computer icon on the desktop, or go the Start menu and point to My Computer, then click it. Double-click the camera icon. Click Take a new picture in the Camera Tasks box. . PC Camera Module There are 2 camera options available for this computer, depending on your purchase configuration. The 1.3M pixel camera module uses the BisonCap application to capture video files, and the 2.
Windows XP Information PC Camera Driver Installation 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual CD-ROM (WinXP) into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 2.PC Camera, Web cam > Yes. For the 1.3M Pixel Camera Module: 1. Choose the language you prefer and click Next. 2. Click Next > Finish to restart the computer. 3.
Windows XP Information PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then doubleclick the Sounds & Audio Devices icon (Sounds, Speech, and Audio Devices in Category View). 2. Click Advanced in the Volume > Device volume tab. 3. Click Options and scroll down and click Properties. 4.
Windows XP Information BisonCap (1.3M Cam)/VideoView (2.0 Cam) BisonCap and VideoView are video viewers for general purpose video viewing and testing, and capturing video files to .avi format. 1. 2. 3. Run the BisonCap/VideoView application from the Start > Programs/All Programs > BisonCam/USB2.0 PC Camera menu (it is recommended that you set the capture file before the capture process - see Set Capture File below).
Windows XP Information Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties) If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Windows XP Information Eliminating Screen Flicker If you find that the video screen in the BisonCap/VideoView program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. Run the BisonCap/VideoView program. Go to Options and scroll down to select Video Capture Filter.... For Bison Cap: 3. Click either 50Hz or 60Hz under Frequency in Property Page (tab). For VideoView: 4. Click either 50Hz or 60Hz under Flickering Reduction in Image (tab).
Windows XP Information Zoom The BisonCap and VideoView programs allow you to zoom the camera in and out. 1. Run the BisonCap/VideoView program. For Bison Cap: 2. Go to Zoom and select Zoom Out/Zoom In. Figure D - 30 Zoom/Setting For VideoView: 3. Go to Options and scroll down to select Setting (Use the slider to adjust the zoom level, and click OK to save the setting). Bison Cap VideoView Snapshot Folder The Snapshot folder’s default location is on the desktop.
Windows XP Information Fingerprint Reader Module If you have included the fingerprint reader in your purchase option you will need to install the driver as per the instructions below. Help & Manual Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full security protection. Right-click the taskbar icon to bring up the menu to select Help. Before beginning the enrollment process it is recommended that you go through the fingerprint tutorial.
Windows XP Information Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Use the Fn + _ ( ))key combination to toggle power to the 3.5G module, and check the indicator to see if the module is powered on or not (see Table D - 3, on page D - 9/ Table D - 1, on page D - 5/ Table 1 - 3, on page 1 - 12). D D - 54 3.5G Module 3.
Windows XP Information 3G Watcher Application Installation 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual CD-ROM (WinXP) into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 4.Install 3G Driver > Yes. 4. Click Next. 5. Choose your region, and click Next. 6. Click the button to accept the license agreement, and then click Next. 7. Click Next > Install. 8. Click Finish, and the 3G Watcher icon will appear on the desktop. 9.
Windows XP Information AHCI Configuration You can configure your Serial ATA hard disk in AHCI (Advanced Host Controller Interface) mode to enable advanced serial ATA features, such as Native Command Queuing, to increase hard disk storage performance. If you want to use enable AHCI mode, you must enable this mode before installing your operating system. If you currently use Compatible mode (the most compatible mode can be used for operating systems such as Linux etc.
Windows XP Information 5. 6. 7. 8. 9. 10. A SATA AHCI driver diskette will now be created for you. Remove the SATA AHCI driver diskette. Start-up your notebook computer and press to enter the BIOS. Use the arrow keys to select the Advanced menu heading. Use the arrow keys to select (highlight in white) the Sata Control Sub-Menu, and press . Press to access the dialog box and use the arrow keys to select Enhanced, and then press again. 11.
Windows XP Information 15. Insert the Microsoft Windows OS CD into the CD/DVD drive of the notebook computer, and attach the external USB floppy disk drive to one of the notebook computer’s USB ports. 16. Press to bring up the Setup Configuration menu and press to save the changes and exit the BIOS and reboot the computer. 17. Press a key when you see the message "Press any key to boot from CD". 18.
