Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. • Only use a power adapter approved for use with this computer.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface Contents Notice .................................................................................I FCC Statement .............................................................II Instructions for Care and Operation .......................... IV Power Safety .............................................................. VI Battery Precautions ...................................................VII Cleaning .................................................................. VIII Servicing ...............
Preface Audio Features .............................................................2-13 8 Channel Sound Support .........................................2-14 Adding a Printer ...........................................................2-15 USB Printer ..............................................................2-15 Parallel Printer ..........................................................2-15 Power Management Overview ........................................................................
Preface Bluetooth ..................................................................4-10 Port Replicator ..........................................................4-10 BIOS Utilities Overview ........................................................................5-1 The Setup Utility ............................................................5-2 Entering Setup ............................................................5-2 Setup Screens ..............................................................
Preface Troubleshooting Overview ........................................................................8-1 Basic Hints and Tips ......................................................8-2 Backup and General Maintenance .................................8-3 Viruses ...........................................................................8-4 Upgrading and Adding New Hardware/Software ..........8-5 Power .............................................................................8-7 Display ................
Preface Specifications Processor ....................................................................... C-2 Core Logic .................................................................... C-2 Memory ......................................................................... C-2 Security ......................................................................... C-2 BIOS ............................................................................. C-2 LCD .......................................................
Preface XVIII
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk, optical device, 7-in-1 card reader, ExpressCard/34/54), Function/Hot Keys, TouchPad & Mouse, Audio & Printer.
1 Quick Start Guide Model & Design Differences This notebook series includes two different model types (Model A or Model B) based upon their specification details (see Table 1 - 1 below). The series also includes two different designs which vary slightly in color and appearance. However both designs incorporate the same features, ports and jacks etc.
Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the User’s Manual. You may also find the notes marked with a of interest to you.
1 Quick Start Guide Not Included Operating Systems (e.g. Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find this manual refers to the Microsoft Windows XP (Home & Professional Editions) operating system.
Quick Start Guide System Startup 1. 2. 3. 4. 5. 6. 7. Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter (Note: If you have included the Port Replicator in your purchase option see page 7 - 13).
1 Quick Start Guide System Map: Top View with LCD Panel Open 1. 2. 3. 4. 5. 6. 7. 8. 9. 1 Optional Built-In PC Camera LCD Speakers Power Button Hot Key Buttons Keyboard TouchPad and Buttons Built-In Microphone LED Indicators Wireless Device Operation Aboard Aircraft 2 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
Quick Start Guide LED Indicators Color Description The LED indicators display helpful information about the current status of the computer.
1 Quick Start Guide Hot Key Buttons & Keyboard These buttons give instant access to the default Internet browser and e-mail program, and activates the PC Camera. Table 1 - 3 - Hot Key Buttons Hot Key The keyboard has a numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly (see Figure 1 - 3).
Quick Start Guide Function Keys The function keys (F3 - F12 etc.) will act as hot keys when pressed while the Fn key is held down (see “Function Keys” on page 2 - 8).
1 Quick Start Guide System Map: Front & Rear Views 1. 2. 3. 4. 5. 6. LED Indicators Serial Port Mini-IEEE 1394 Port 1 * USB Port DC-In Jack Battery 1 1 3 4 6 2 5 Figure 1 - 4 - Front & Rear Views Mini-IEEE 1394 The Mini-IEEE 1394 port only supports SELF POWERED IEEE 1394 devices.
Quick Start Guide System Map: Left View Figure 1 - 5 - Left View 2 1 Changing DVD Regional Codes Go to the Control Panel and double-click System > Hardware (tab), click Device Manager, then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialogue box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code (see “DVD Regional Codes” on page 2 - 5).
1 Quick Start Guide System Map: Right View Figure 1 - 6 - Right View 1. 2. 3. 4. 5. 6. 7. ExpressCard Slot (see page 2 - 7) 7-in-1 Card Reader 2 * USB 2.0 Ports Vent/Fan Intake RJ-45 LAN Jack 7-Pin S-Video-Out Jack External Monitor Port 1 2 3 3 5 4 6 7 7-Pin S-Video-Out Jack The 7-pin S-Video Out Jack requires an adapter cable (7-pin S-Video plug to 4-pin S-Video jack adapter) in order to connect to a standard S-Video cable.
Quick Start Guide System Map: Bottom View Figure 1 - 7 - Bottom View 2 1. 2. 3. 4. CPU The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. Overheating To prevent your computer from overheating make sure nothing blocks any Vent/Fan Intake while the computer is in use.
1 Quick Start Guide Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can customize the look of the Start menu by right-clicking the Start menu and selecting Properties from the menu.
Quick Start Guide Video Features Your computer has built-in Intel (Intel 945GM) video. You can switch display devices, and configure display options, from the Display Properties control panel in Windows as long as the appropriate video driver is installed. For more detailed video information see “Intel Video Driver Controls” on page B - 1. To access Display Properties in Windows: 1. 2. 3. 4. 5. 6. 7. 8. Click Start, point to Settings and click Control Panel (or just click Control Panel).
1 Quick Start Guide Display & Graphics Properties 1 2 3 Figure 1 - 9 - Display & Graphics Properties Power Settings Power Settings in Display Settings can affect display brightness, contrast etc. (see “Power Settings” on page B - 12).
Quick Start Guide Display Devices & Options Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display or TV as your display device. A VGA monitor/Flat Panel Display connects to the external monitor port, a TV to the 7-pin S-Video-Out jack. The following display modes are available (see “Intel Video Driver Controls” on page B - 1 for details).
1 Quick Start Guide Power Management Features The Power Options control panel icon in Windows (see page 1 - 14) allows you to configure power management features for your computer. You may conserve power through individual components such as the monitor or hard disk (by means of Power Schemes), or you may use either Stand by or Hibernate mode to conserve power throughout the system (enable Hibernate support from the control panel tab).
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • • • Hard Disk Drive Optical (CD/DVD) Device 7-in-1 Card Reader ExpressCard Slot Function Keys TouchPad and Buttons/Mouse Audio Features Adding a Printer Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 11).
Features & Components 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Features & Components DVD Regional Codes 2 To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - 11. .
Features & Components 2 Card Reader Cover Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. 7-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the Card Reader driver (see “Card Reader/ExpressCard” on page 4 - 10).
Features & Components ExpressCard Slot The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards). ExpressCard/54 is used for applications which require a larger interface slot, e.g. CompactFlash card reader. The number denotes the card width; 54mm for the Express Card/54 and 34mm for the ExpressCard/34. Make sure you install the ExpressCard driver (see “Card Reader/ExpressCard” on page 4 - 10).
Features & Components 2 Application Note The hot key functions will only be displayed if the program is running (i.e. the icon is displayed in the taskbar). If you have closed the program you can run it again from the Start menu (Start > Programs > Startup > HotKey Driver) in Windows. Figure 2 - 6 Hot Key Driver Configuration & Help Menu 2 - 8 Function Keys Function Keys The function keys (F3 - F12 etc.) will act as hot keys when pressed while the Fn key is held down.
Features & Components Fn/Hot Key Function Fn + Esc Help & System Info Fn + F2 TouchPad Toggle Fn + F3 Mute Toggle Fn + F5/F6 Volume Decrease/Increase Fn + F8/F9 Brightness Decrease/Increase Fn + F10 PC Camera Power Toggle Fn + F11 WLAN Module Power Toggle Fn + F12 Bluetooth Module Power Toggle See Figure 2 - 6 on page 2 - 8 Hot Key Note The Help menu will display the function key features, current Battery Life, Power State and CPU Temperature information.
Features & Components Recording Audio 2 The audio record hot key button allows you to record audio from either the builtin microphone, or from a microphone connected to the microphone-in jack. To record on the computer, setup the audio recording options in Windows as follows (see Figure 2 - 7 on page 2 - 11). 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
Features & Components Figure 2 - 7 Audio Setup for Recording (Windows XP) Function Keys 2 - 11 2
Features & Components 2 Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details. TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.
Features & Components Audio Features You can configure the audio options on your computer from the Sounds and Audio Devices Windows control panel, or from the Realtek HD Audio Manager icon in the taskbar/control panel (this will bring up the Realtek Audio Configuration menus). The volume may also be adjusted by means of the Fn + F5/F6 key combination.
Features & Components 2 8 Channel Sound Support 8 Channel Sound Support Double-click the Realtek HD Audio Manager icon in the taskbar to bring up the Realtek control panel. If you wish to configure your system for 8 channel sound support, then the following ports should be used as outputs. Connect the system cables to the following audio jacks: • • • • Click Audio I/O (tab). Select 8CH Speaker from the pull-down menu. Click OK to save. Connect the cables to the audio jacks as outlined.
Features & Components Adding a Printer The most commonly used peripheral is a printer. The following conventions will help you to add a printer; however it is always best to refer to the printer manual for specific instructions and configuration options. USB Printer Most current printers have a USB interface connection. You may use any one of the ports to connect the printer. Install Instructions: 1. 2. 3. 4. 5.
Features & Components 2 2 - 16
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer uses the ACPI power management system. Power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management 3 Port Replicator AC/DC Adapter You will be provided with a 90W AC/DC adapter if you purchase the port replicator option. If you are using the computer with the Port Replicator, then you must use the 90W AC/DC adapter to power the port replicator and computer (DO NOT USE the computer’s AC/DC adapter to power the Port Replicator). See “Port Replicator” on page 7 - 13 for more information. The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack.
Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.
Power Management 3 Resuming Operation Press the Sleep/Resume key combination (Fn + F4), or power button to resume from Monitor or Hard Disk Stand by. Figure 3 - 1 Power Schemes 3 - 4 Power Schemes Power Schemes You can set your computer to conserve power through individual components by means of Power Schemes.
Power Management Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source.
Power Management System Power Options 3 You can use the system power options to stop the computer’s operation and restart where you left off. This system features Stand by and Hibernate sleep mode levels (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - see “Hibernate” on page 3 - 7). Hibernate Mode vs. Shutdown Hibernate mode and Shutdown are the same in that the system is off and you need to press the power button to turn it on.
Power Management Stand by Stand by saves the least amount of power, but takes the shortest time to return to full operation. During Stand by the hard disk is turned off, and the CPU is made to idle at its slowest speed. All open applications are retained in memory. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Stand by mode to save power.
Power Management 3 Sleep Button You may also configure the Sleep/Resume key combination (Fn + F4) from the menu illustrated in Figure 3 - 3. In Windows this is referred to as the Sleep button. Configuring the Power Button The power button may be set to send the computer in to either Stand by or Hibernate mode. In Stand by mode, the LED will blink green. In Hibernate mode the LED will be off (battery) or red (AC/DC adapter).
Power Management Battery Information Please follow these simple guidelines to get the best use out of your battery. Low Battery Warning New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page 3 - 12 for instructions on how to do this). Battery Life Your computer’s battery life is dependent upon many factors, including the programs you are running, and peripheral devices attached.
Power Management 3 Conserving Battery Power To conserve battery power: Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter. Close modem or communication applications when they are not being used. Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days.
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other 3 Damaged Battery Warning Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center.
Power Management Battery FAQ 3 Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions. How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Navigate (Browse..) to D: 4 You will notice that many of the instructions for driver installation require you to “Navigate (Browse) to D:”. We assume that you will install all drivers and utilities from the built-in CD device and it is assigned to “Drive D:”. In addition, all file extensions can be seen In this case “D:” is the drive specified for your CD device. Not all computers are setup the same way, and some computers have the CD listed under a different drive letter - e.g.
Drivers & Utilities Service Packs Check the warnings on the following pages regarding installation of the appropriate Service Pack for your Windows OS. Make sure you have installed the appropriate Service Pack before installing all the drivers. Service Pack Installed To see which Service Pack is currently installed on your computer go to the General tab of the System control panel. Right-click the My Computer icon on the desktop or in the Start menu and select Properties.
Drivers & Utilities 4 Authorized Driver Message Updating/Reinstalling Individual Drivers If you receive a message telling you that the driver you are installing is not authorized (Digital Signature Not Found), just click Yes or Continue Anyway to ignore the message and continue the installation procedure. If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.
Drivers & Utilities Driver Installation This section covers driver and utility installation instructions for Windows XP Home & Professional editions. Insert the Device Drivers & Utilities + User’s Manual CD-ROM and click the appropriate driver name from the from the Driver Installation menu and follow the instructions to install the driver. Alternatively click Start (or click the Browse CD button) and navigate (Browse..) to the setup.exe to follow the manual setup instructions. 6.
Drivers & Utilities 4 New Hardware Found Service Pack Installation If you see the message “New Hardware Found” (Found New Hardware Wizard) during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure as directed. Make sure you install the appropriate service pack for your operating system before installing any drivers (see “Service Packs” on page 4 - 3).
Drivers & Utilities WinXP Driver Installation Procedure Chipset 1. Double-click Chipset. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\inf_update\infinst_autol.exe and click OK. 2. Click Next > Yes > Next. 3. Click Finish to restart the computer. IAA (Intel Application Accelerator) Note: This driver is only required (and will only appear in the Driver Installation menu) if you have enabled AHCI mode for SATA hard disks - see “Setting Up AHCI SATA Mode” on page 5 - 6.
Drivers & Utilities 4 Video (VGA) 1. Double-click VGA. OR Navigate (Browse..) to D:\Drivers\VGA\Setup.exe and click OK. 2. Click Next > Yes. 3. Click Finish to restart the computer. Audio 1. Double-click Audio. OR Navigate (Browse..) to D:\Drivers\Audio\Setup.exe and click OK. 2. Click Next (click Continue Anyway if asked if you want to continue at any time). 3. Click Finish to restart the computer. 4 - 8 Driver Installation LAN 1. Double-click Lan. OR Click Start (menu) > Run... and navigate (Browse...
Drivers & Utilities Modem 1. Double-click Modem. OR Click Start (menu) > Run... and navigate (Browse...) to (one of the following) D:\Drivers\Modem\HXFSetup.exe D:\Drivers\Modem\Setup.exe and click OK. 2. Click OK > OK. 3. The modem is ready for dial-up configuration. Modem Country Selection TouchPad 1. Double-click TouchPad. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\Touchpad\SETUP.EXE and click OK. 2.
Drivers & Utilities 4 Card Reader/ExpressCard 1. Double-click CardReader. OR Click Start (menu) > Run... and navigate (Browse...) to D:\Drivers\CardReader\setup.exe and click OK. 2. Click Next. 3. Click Finish to restart the computer. Hot Key 1. Double-click Hot Key. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\Hotkey Driver\Setup.EXE and click OK. 2. Click Next > Install > Finish. 3. Click Finish to restart your computer.
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Configuration: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make.
BIOS Utilities Setup Menus 5 The Setup menus shown in this section are for reference only. Your computer’s menus will indicate the configuration appropriate for your model and options. The Setup Utility The Insyde H20 Setup Utility tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup To enter the Insyde H20 Setup Utility, turn on the computer and quickly press F2 during the startup process.
BIOS Utilities Main Menu Main Main Advanced Figure 5 - 1 InsydeH20 Setup Utility Security Power Boot Exit Insyde EFI Version H8 Version R1.00.P03_0_GI02 04.0P.02 Processor Type System Bus Speed System Memory Speed Genuine Intel(R) CPU T2500 @ 2.00GHz 667 MHz 667 MHz Cache RAM 2048 KB Total Memory SODIMM 0 SODIMM 1 256 MB 256 MB [Not Installed] Language System Time System Date [16:33:11] [04:27:2006] Main Menu Select the current default language used by the EFI.
BIOS Utilities Advanced Menu Figure 5 - 2 Advanced Menu Main Boot Advanced Advanced Configuration IDE Configuration Video Configuration InsydeH20 Setup Utility Security Power Boot Exit Configures Boot Settings. 5 +<> Select Boot Device Select Screen Select Item Enter Select SubMenu F9 = Setup Defaults F10 = Save and Exit Esc = Exit The sub-menus in the Advanced menu allow you to configure advanced options for various hardware features.
BIOS Utilities Boot Configuration (Advanced Menu) Use this menu to configure the Number Lock mode at startup (boot). IDE Configuration (Advanced Menu) Configure either a CD Device or HDD on the computer’s IDE Channel/SATA port/ PATA port from this menu. SATA Configure as > IDE Configuration (Advanced Menu) You can use this menu to set the options for your hard disk. Only make changes if you are sure of what you are doing (see overleaf).
BIOS Utilities Setting Up AHCI SATA Mode Before setting up your Serial ATA hard disk in AHCI mode you will need to prepare the following: 1. 2. 3. 4. 5 An operable computer with a floppy drive, running the Windows XP OS. The Device Drivers & Utilities + User’s Manual CD-ROM. An external USB floppy disk drive. A prepared formatted blank 3.5" 1.44MB floppy diskette. AHCI Setup Procedure 1. 2. 3. 4. 5. 6. 7. 8. 9.
BIOS Utilities 10. Insert the Microsoft Windows OS CD into the CD/DVD drive of the notebook computer, and attach the external USB floppy disk drive to one of the notebook computer’s USB ports. 11. Select Exit Saving Changes from the Exit menu and click OK to exit the BIOS and reboot the computer. 12. Press a key when you see the message "Press any key to boot from CD". 13. Press the F6 key when you see the message “Press F6 if you need to install third party SCSI or RAID driver”. 14.
BIOS Utilities Security Menu 5 The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS. Figure 5 - 4 Security Menu Main Advanced InsydeH20 Setup Utility Security Power Boot Exit Security Supervisor Password : User Password : Not Installed Not Installed Install or Change the password.
BIOS Utilities Set User Password (Security Menu) You can set a password for user mode access to the Setup utility. This will not affect access to the computer OS (only the Setup utility). Many menu items in the Setup utility cannot be modified in user mode. You can only set the user password after you have set the supervisor password.
BIOS Utilities CST Support for WinXP with Service Pack 1 5 Power Menu Main Advanced Advanced CPU Control Security InsydeH20 Setup Utility Power Boot Exit Power These items control various CPU parameters. If you wish to install Windows XP with Service Pack 1, then disable CST Support from this menu before installing the operating system.
BIOS Utilities Boot Menu Main Advanced PXE Boot to LAN InsydeH20 Setup Utility Security Power Boot Exit Boot Disables or enables PXE boot to LAN.
BIOS Utilities Exit Menu Figure 5 - 7 Exit Menu Main Advanced Security Exit Saving Changes Exit Discarding Changes Load Optimal Defaults Discard Changes 5 InsydeH20 Setup Utility Power Boot Exit Exit Exit system setup and save your changes. +<> Select Boot Device Select Screen Select Item Enter Select SubMenu F9 = Setup Defaults F10 = Save and Exit Esc = Exit Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup.
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. 4. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Slide the battery out in the direction of the arrow 3 .
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CD-ROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer 4. 5. 6. Slide the hard disk of arrow 5 . Lift the hard disk up in the direction of arrow 6 . Reverse the process to install a new hard disk drive.
Upgrading The Computer Upgrading the Optical (CD/DVD) Device 1. 2. 3. 4. 5. Turn off the computer, and turn it over and remove the battery. Locate the hard disk bay cover and remove screws 1 - 3 . Remove the hard disk bay cover 4 . Remove the screw at point 5 , and use a screwdriver to carefully push out the optical device at point 6 . Reverse the process to install the new device.
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 200 pin Small Outline Dual In-line (SODIMM) DDRII (DDR2) type memory modules (see “Memory” on page C - 2 for details of supported module types). The total memory size is automatically detected by the POST routine once you turn on your computer. 1. 2. Turn off the computer, and turn it over and remove the battery. Locate the CPU/RAM bay cover and remove screws 1 - 7 .
Upgrading The Computer 3. Remove the bay cover 8 . Figure 6 - 6 CPU/RAM Bay Cover Removed 8 6 Contact Warning Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. 4. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 9 & 10 ) in Figure 6 - 7.
Upgrading The Computer 5. The RAM module will 11 pop-up, and you can remove it. Figure 6 - 8 RAM Module Removal 11 11 11 6 6. 7. Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. 8. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit without much pressure. 9.
Upgrading The Computer Warranty The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 6 Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard.
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. • • • • PC Camera Intel WLAN Module Bluetooth Module Port Replicator Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Modules & Options Taking Still Pictures Double-click the My Computer icon on the desktop, or go the Start menu and point to My Computer, then click it. Double-click the BisonCam, NB Pro icon. . PC Camera Before installing the PC Camera driver, make sure that the optional PC Camera is on. Use the Fn + F10 key combination (see “Function Keys” on page 1 - 9) to toggle power to the PC Camera module. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 6.
Modules & Options PC Camera Driver Installation 1. Make sure the module is powered on (click Cancel if you see a “New Hardware Found” message), and then insert the Device Drivers & Utilities + User’s Manual CD-ROM into the CD/DVD drive. 2. Double-click Camera. OR Click Start (menu) > Run... and navigate (Browse...) to D:\Drivers\Camera\Setup.exe and click OK. 3. Choose the language you prefer and click OK. 4. Click Next > Finish to restart the computer. 5.
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows (see Figure 7 - 1 on page 7 - 5). 1. Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then double-click the Sounds & Audio Devices icon (Sounds, Speech, and Audio Devices in Category View). 2. Click Advanced in the Volume > Device volume tab. 3. Click Options and scroll down and click Properties. 4.
Modules & Options Figure 7 - 1 Audio Setup (Windows XP) 7 PC Camera 7 - 5
Modules & Options Pre-Allocating File Space You may pre-allocate the file size for the capture file in the BisonCap application. You can choose to ignore this by clicking Cancel. 7 Pre-allocating space on the hard disk can improve the capture quality (particularly of large capture files), by reducing the amount of work the hard disk has to do in finding space for the video data as it is being captured. You may find it helpful to defragment the HDD before capture.
Modules & Options Eliminating Screen Flicker If you find that the video screen in the BisonCap application is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3. Run the BisonCap program. Go to Options and scroll down to select “Video Capture Filter...”. Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Modules & Options PC Camera Hot Keys Snapshot Folder The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture using the application hot key. 7 If you accidentally delete or move the folder, you can create a new Snapshot folder on the desktop in order to capture the files.
Modules & Options Intel WLAN Module If you have included an Intel 3945ABG (802.11a/b/g) PCIe WLAN module in your purchase option, you will have the appropriate software CD provided for your module. Before installing the Intel 3945ABG (802.11a/b/g) PCIe WLAN driver, make sure that the Wireless LAN module is on. Use the Fn + F11 key combination (see “Function Keys” on page 1 - 9) to toggle power to the Wireless LAN module.
Modules & Options User Guide Insert the Device Drivers & Utilities + User’s Manual CD-ROM and navigate (Browse..) to D:\Drivers\Options \WLAN\Autorun.exe. 7 Click View User Guide (button) as per Figure 7 - 4. You can also view the Help menu from the Intel(R) PROSet/Wireless control panel (or press F1 to bring up the help menu when the control panel is active). Intel WLAN Driver Installation 1.
Modules & Options Bluetooth Module Before installing the Bluetooth driver, make sure that the optional Bluetooth module is on. Use the Fn + F12 key combination (see “Function Keys” on page 1 - 9) to toggle power to the Bluetooth module. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 6. Bluetooth Driver Installation 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual CD-ROM into the CD/DVD drive. 2.
Modules & Options User Guide 7 View the BlueSoleil User Guides from the Help Menu (or press the F1 key) in the IVT Corporation BlueSoleil - Main Window control panel. Click BlueSoleil User Guides in the Contents tab, and click to select the appropriate User Guide from the panel on the right.
Modules & Options Port Replicator If you have included the Port Replicator in your purchase option, the device will allow you to easily attach the notebook to standard, non-portable devices e.g. a printer or monitor. Note the sidebar warning on the power supply. Port Replicator AC/DC Adapter You will be provided with a CD including drivers for the serial (COM) port, and for the network (LAN) jack. See “Port Replicator Setup Instructions:” on page 7 - 14 for configuration information.
Modules & Options Port Replicator Setup Instructions: 1. 2. 3. 4. 7 5. 6. 7. 8. Turn the computer OFF. Attach the Port Replicator’s external monitor cable to the external monitor port on the right of the computer. Attach the Port Replicator’s power cable to the DC-In jack at the rear of the computer.
Modules & Options Port Replicator Network (LAN) Driver (WinXP) 1. Attach the Port Replicator as per the instructions in “Port Replicator Setup Instructions:” on page 7 - 14. 2. Insert the provided Port Replicator CD into the computer’s CD/DVD drive. 3. If you can see the My Computer icon on the desktop (if you cannot see the My Computer icon go to step 4) click on it once to select it, then rightclick it to make the sub-menu appear and scroll down to Properties and click on it (go to step 5). 4.
Modules & Options 7 7 - 16
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “LED Indicators” on page 1 - 7) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Power Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED power indicator , is blinking red. Low Battery. Plug in the DC power source.
Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 13). Make sure you’re using the correct adapter.
Troubleshooting Display Problem Nothing screen. appears Possible Cause - Solution on The system is in a power saving mode. Toggle the sleep/resume key combination, Fn + F4 (see “Sleep Button” on page 3 - 8). The screen controls need to be adjusted. Toggle the screen control key combinations Fn + F8/F9. If you’re connected to an external monitor, make sure it’s plugged in and turned on. You should also check the monitor’s own brightness and contrast controls. The computer is set for a different display.
Troubleshooting Boot Password Problem You forget password. the Possible Cause - Solution boot If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Audio & CD Device Problem Possible Cause - Solution The sound cannot be heard or the volume is very low. The volume might be set too low. Check the volume control in the Volume Control Panel in the Windows taskbar, or use the key combination Fn + F5 and F6 (see “Audio Features” on page 2 - 13) to adjust. The compact disc cannot be read. The compact disc is dirty. Clean it with a CD-ROM cleaner kit. The compact disc tray will not open when there is a disc in the tray.
Troubleshooting Keyboard Problem Unwelcome numbers appear when typing. Possible Cause - Solution If the LED is lit, then Num Lock is turned ON. (see “LED Indicators” on page 1 - 7). Other Keyboards 8 If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work.
Troubleshooting Operation Problem Possible Cause - Solution The system freezes or the screen goes dark. The system’s power saving features have timed-out. Use the AC/DC adapter, press the sleep (Fn + F4) key combination, or press the power button if no LEDs are lit. The system never goes into a power saving mode. Power Options features are not enabled. Go to the Windows Power Options menu and enable the features you prefer (see “System Power Options” on page 3 - 6).
Troubleshooting Modules 8 Problem Possible Cause - Solution The Wireless LAN/ Bluetooth modules cannot be detected. The modules are off. Check the LED indicator and/or hot key indicator to see if the WLAN/ Bluetooth module is on or off (see “LED Indicators” on page 1 - 7). If the LED indicator is off, then press the Fn + F11 (WLAN) or Fn + F12 (Bluetooth) key combination(s) in order to enable the modules (see “Function Keys” on page 1 - 9). The PC Camera module cannot be detected. The module is off.
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer.
Interface (Ports & Jacks) Item Description Mini-IEEE 1394 Port This port allows a high-speed connection to various peripheral devices, e.g. external disk drives and digital cameras (see note below). Mini-IEEE 1394 Port The Mini-IEEE 1394 port only supports SELF POWERED IEEE 1394 devices. RJ-11 Phone Jack RJ-45 LAN Jack Security Lock Slot Serial Port This port connects to the built-in modem. You may plug the telephone line directly into this RJ-11 telephone connection. Note: Broadband (e.g.
Interface (Ports & Jacks) Item Description S/PDIF-Out Jack This S/PDIF (Sony/Philips Digital Interface Format) Out Jack allows you to connect your DVDcapable PC to a Dolby AC-3 compatible receiver for “5.1” or ‘dts’ surround sound. S-Video-Out Jack Connect your television to your computer and view DVDs, VCDs or anything else your computer can display. You will need an S-Video cable to make the connection. Enable this jack from the video driver controls. USB 2.0/1.1 Ports These USB 2.
Interface (Ports & Jacks) Optional Port Replicator Ports and Jacks Item DC-In Jack Description Plug the supplied AC/DC adapter into this jack to power your computer. External Monitor (VGA) Port This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD (see “Display Devices” on page B - 5). Parallel Port Connect a parallel type printer to this port.
Interface (Ports & Jacks) Item Description USB 2.0/1.1 Ports These USB 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc.
Intel Video Driver Controls Appendix B: Intel Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 15. Intel Video Driver Installation Make sure you install all the drivers in the order indicated in Table 4 - 1, on page 4 - 6. Instructions for installing the video driver are repeated below. 1. Click 2.Install Video Driver > Yes from the Drivers Installer menu. OR Navigate (Browse..) to D:\Drivers\Video\Setup.exe and click OK. 2. Click Next > Yes.
Intel Video Driver Controls DVMT Notes DVMT is not local video memory. DVMT will not function in MS-DOS. DOS uses the legacy memory indicated. Figure B - 1 DVMT Memory Requirements B Dynamic Video Memory Technology Intel® DVMT 3.0 automatically and dynamically allocates as much (as configured in the BIOS - see Page 5 - 5) system memory (RAM) as needed to the video system (the video driver must be installed - see page B - 1). DVMT returns whatever memory is no longer needed to the operating system.
Intel Video Driver Controls Intel Graphics Properties More advanced video configuration options are provided by the Intel(R) Graphics Media Accelerator Driver for Mobile control panel. 1. 2. 3. Open Display Properties > Settings > Advanced (see page 1 - 15). Click the Intel(R)... tab and click Graphics Properties (button). You can also access Graphics Properties from the Windows Intel(R) GMA Driver for Mobile control panel, or from the taskbar icon .
Intel Video Driver Controls Help Menus You may make changes to the devices, color, schemes, Hot Keys etc. by clicking the appropriate menu item or button. Click Information (button) to obtain useful information about the graphics properties of the computer, and see the Support tab in Information to get weblinks to the latest information on the Intel Website. Right-click on many of the items in the tabs to bring up the “What’s This?” button. Click the “What’s This?” button to bring up the help menu.
Intel Video Driver Controls Display Devices Besides the built-in LCD, you can also use an external monitor/flat panel display or TV as your display device. The following are the display options: 1. 2. 3. 4. The built-in LCD. An external monitor connected to the external monitor port. A flat panel display connected to the external monitor port. A TV connected to the 7-pin S-Video-Out jack.
Intel Video Driver Controls Intel Display Note Note that the notebook is the default Primary display device and may not be changed. Attaching Other Displays If you prefer to use a monitor or flat panel display, connect it to the external monitor port on the right of the computer. 1. 2. 3. 4. Attach your external monitor to the external monitor port (or TV to the 7-pin SVideo-Out jack), and turn it on.
Intel Video Driver Controls Display Modes Single Display Only one of your attached displays is used. Intel(R) Dual Display Clone This mode will drive multiple displays with the same content. Each device may be configured independently for different resolutions, refresh rates, color quality etc. Use this feature to display the screen through a projector for a presentation. Extended Desktop This mode allows a desktop to span multiple displays and acts as a large workspace.
Intel Video Driver Controls To Enable Intel(R) Dual Display Clone Mode 1. 2. 3. 4. 5. Figure B - 5 Display Devices & Settings B B - 8 Display Modes Attach your external monitor to the external monitor port (or TV to the 7-pin S-Video-Out jack), and turn it on. Go to the Graphics Properties control panel (see “Intel Graphics Properties” on page B - 3) and click Display Devices. Click to choose Intel(R) Dual Display Clone. Click Apply, and OK to confirm the settings change.
Intel Video Driver Controls To Enable Extended Desktop Mode: 1. 2. 3. 4. 5. Attach your external monitor to the external monitor port (or TV to the 7-pin S-Video-Out jack), and turn it on. Go to the Graphics Properties control panel (see “Intel Graphics Properties” on page B - 3) and click Display Devices. Click to choose Extended Desktop. Click Apply, and OK to confirm the settings change. Click Display Settings to adjust the settings for the attached devices.
Intel Video Driver Controls To Enable Extended Desktop (Display Properties) 1. Display Settings Extended Desktop 2. Use the control panel to drag the monitors to match the physical arrangement you wish to use. 3. 4. 5. You can drag any icons or windows across to either display desktop, which makes it possible to have one program visible in one of the displays, and a different program visible in the other display.
Intel Video Driver Controls TV Settings If you are using a TV as a display device adjust the display settings as follows: 1. 2. 3. 4. 5. 6. 7. Attach your TV to the 7-pin S-Video-Out jack and turn it on. Go to the Graphics Properties control panel (see “Intel Graphics Properties” on page B - 3) and click Display Devices. Choose the television as one of your display devices. Click Apply, and OK to confirm the settings change. Click Display Settings and click Television (tab).
Intel Video Driver Controls Power Settings Click the Power Settings button in Display Settings (tab) to set the display options based on power status of the computer. Intel Display Power Saving Technology If this option is enabled, the system will adjust LCD brightness and contrast in order to save power (when the notebook LCD is the only display device and the system is battery powered).
Intel Video Driver Controls B Power Settings B - 13
Intel Video Driver Controls B B - 14 Power Settings
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed or updated due to the manufacturer's release schedule. Check with your service center for details.
Specifications Feature Specification Intel® Core® Processor’s are Supplied as Options for Both Model A & Model B Computers Processor Intel® Core™ Duo Processor (478-pin) Micro-FC-PGA Package T2300/ T2400/ T2500/ T2600/ T2700 65nm (65 Nanometer) Process Technology 2MB On-die L2 Cache & 667MHz FSB 1.66/ 1.83/ 2.0/ 2.16/ 2.33 GHz Intel® Core™ Solo Processor (478-pin) Micro-FC-PGA Package T1300/ T1400 65nm (65 Nanometer) Process Technology 2MB On-die L2 Cache & 667MHz FSB 1.66/ 1.
Specifications Feature Specification Video Adapter Intel 945GM Integration Dynamic Video Memory Technology DVMT 3.0 - Supports up to 128MB of Video Memory (dynamically allocated from system memory where needed) Supports Analog Monitor Pixel Resolution up to QXGA 2048 * 1536 Integrated High Quality 3D Graphics Engine Supports DirectX 9.0 Supports Two Displays Storage One Changeable 12.7mm(h) Optical Device (CD/DVD) Type Drive (see “Optional” on page C - 5 for drive options) Easy Changeable 2.5" 9.
Specifications Feature Interface Specification Three USB 2.0 Ports One Com Port One External Monitor Port One Headphone-Out Jack (7.1 CH) One Microphone-In Jack (7.1CH) One Line-In Jack (7.1CH) One S/PDIF Output Jack (7.1CH) One RJ-11 Jack for Plug & Play Fax/Modem One RJ-45 Jack for 10Mb/ 100Mb/ 1000Mb Fast Ethernet One Mini-IEEE 1394 Port One S-Video-Out Jack (supports HDTV) One DC-in Jack Note: External 7.
Specifications Feature Power Specification Full Range AC/DC Adapter 19V, 3.42A, 100~240V, 47~63Hz Full Range AC/DC Adapter 20V, 4.5A (90 Watts), 100~240V, 50~60Hz (Supplied for the Optional Port Replicator Only) Battery For Model A Computers Only 6 Cell Smart Lithium-Ion Battery Pack, 4400mAH (48.8W) For Model B Computers Only 6 Cell Smart Lithium-Ion Battery Pack, 4000mAH (44.
Specifications C C - 6
