Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. VI • Only use a power adapter approved for use with this computer.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface Contents Notice .................................................................................I FCC Statement .............................................................II Instructions for Care and Operation .......................... IV Power Safety .............................................................. VI Battery Precautions ...................................................VII Cleaning .................................................................. VIII Servicing ...............
Preface USB Printer ..............................................................2-14 Parallel Printer ..........................................................2-14 Power Management Overview ........................................................................3-1 The Power Sources ........................................................3-2 AC/DC Adapter ...........................................................3-2 Battery .........................................................................
Preface Setting a Boot Password ..............................................5-4 Setup Screens ...............................................................5-5 Main Menu .....................................................................5-6 System Time & Date (Main Menu) ...............................5-6 IDE Channel 0/2 Master (Main Menu) ..........................5-7 QuickBoot Mode: (Main Menu) ....................................5-7 System/Extended Memory: (Main Menu) .....................
Preface Interface (Ports & Jacks) Notebook Ports and Jacks ............................................. A-2 VIA Video Driver Controls VIA Video Driver Installation ...................................... B-1 Video ......................................................................... B-1 Advanced Video Controls ............................................. B-2 Video Driver Controls ............................................... B-2 Video Memory .........................................................
Preface VIA S3Tray Plus Utility ........................................... D-12 Display Devices (VIA) ............................................... D-14 Display Modes (VIA) ................................................. D-15 Power Management Features ...................................... D-17 Advanced Configuration and Power Interface ......... D-17 The Power Sources ..................................................... D-18 AC/DC Adapter ........................................................
Preface XVIII
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 • Chapter 3 • Chapter 4 • Chapter 5 • Chapter 6 • Chapter 7 • Chapter 8 • Appendix A • Appendix B • Appendix C • Appendix D A guide to using some of the main features of the computer e.g.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the User’s Manual. You may also find the notes marked with a of interest to you. Beginners and Not-So-Advanced Users Notes Check the light colored boxes with the mark above to find detailed information about the computer’s features.
Quick Start Guide Not Included Operating Systems (e.g. Windows Vista/Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1.
1 Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the following operating systems are supported.
Quick Start Guide System Startup 1. 2. 3. 4. 5. 6. 7. Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle, and press the power button to turn the computer “on”.
1 Quick Start Guide System Map: LCD Panel Open 1. 2. 3. 4. 5. 6. 7. 8. 9. 1 Wireless Device Operation Aboard Aircraft 2 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Use the key combinations to toggle power to the WLAN/ Bluetooth modules, and check the LED indicator icon to see if the modules are powered on or not (see Table 1 - 2, on page 1 - 7/ Table 1 - 4, on page 1 10).
Quick Start Guide LED Indicators The LED indicators display helpful information about the current status of the computer.
1 Quick Start Guide Hot Key Buttons These buttons give instant access to the functions indicated in the table below. The Application hot key functions depend on whether or not a PC Camera module installed.
Quick Start Guide Keyboard The keyboard has a numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly (see Figure 1 - 3). Function Keys NumLk & ScrLk Keys Numeric Keypad Fn Key Figure 1 - 3 - Keyboard Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically.
1 Quick Start Guide Function Keys The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down (see “Function Keys/Hot Keys” on page 2 - 9).
Quick Start Guide System Map: Front & Rear Views 1 2 1. 2. 3. 4.
1 Quick Start Guide System Map: Left View Figure 1 - 5 - Left View 1. 2. 3. 4. 5. 6. 7. Security Lock Slot Optical Device Drive Bay (see page 2 - 3) RJ-11 Modem Jack S/PDIF-Out Jack Microphone-In Jack Headphone-Out Jack Line-In Jack 1 CD Emergency Eject If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole.
Quick Start Guide System Map: Right View Figure 1 - 6 - Right View 1. 1 2 3 3 4 5 2. 3. 4. 5. ExpressCard Slot (see page 2 - 7) 7-in-1 Card Reader 2 * USB 2.0 Ports RJ-45 LAN Jack External Monitor Port ExpressCard Slot The ExpressCard Slot accepts either ExpressCard/34 or ExpressCard/54 formats.
1 Quick Start Guide System Map: Bottom View Figure 1 - 7 - Bottom View 1. 2. 3. 4. Vent/Fan Intake/Outlet Battery Hard Disk Bay Cover CPU/RAM Bay Cover 2 CPU 4 The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. Overheating 3 1 To prevent your computer from overheating make sure nothing blocks any Vent/Fan Intake while the computer is in use.
Quick Start Guide Windows Vista Start Menu & Control Panel Most of the control panels, utilities and programs within Windows Vista (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
1 Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display Settings control panel (in Personalization) in Windows Vista. For further information see “VIA Video Driver Controls” on page B - 1. To access Display Properties in Windows Vista: 1. 2. 3. 4. 5. Click Start, and click Control Panel (or point to Settings and click Control Panel).
Quick Start Guide 2 1 3 Figure 1 - 9 - Display Settings Video Features 1 - 17 1
1 Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 15) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • • • • • Hard Disk Drive Optical (CD/DVD) Device 7-in-1 Card Reader ExpressCard Slot TouchPad and Buttons/Mouse Function Keys/Hot Keys Application Quick Buttons Recording Audio Audio Features Adding a Printer Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Figure 2 - 1 Hard Disk Location 2 - 2 Hard Disk Drive Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 10).
Features & Components 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Features & Components DVD Regional Codes 2 To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - 12. .
Features & Components 2 Card Reader Cover Make sure you keep the rubber cover provided in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. 7-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the Card Reader driver (see “CardReader” on page 4 - 6).
Features & Components ExpressCard Slot The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards). ExpressCard/54 is used for applications which require a larger interface slot, e.g. CompactFlash card reader. The number denotes the card width; 54mm for the Express Card/54 and 34mm for the ExpressCard/34.
Features & Components 2 Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details. TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.
Features & Components Function Keys/Hot Keys The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key driver is installed (see “Hot Key Utility” on page 4 - 7). After installing the driver an icon will appear in the taskbar.
Features & Components 2 Application.exe You will need to locate the actual application executable (.exe) file, not just the shortcut. To find the application rightclick its shortcut on the desktop and click Properties. Click the shortcut (tab) and see where the executable file is located by clicking the Open File Location (button).
Features & Components Recording Audio The audio record hot key button allows you to record audio from either the builtin microphone, or from a microphone connected to the microphone-in jack. To record on the computer, setup the audio recording options in Windows as follows (see Figure 2 - 8 on page 2 - 12). 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Recording (tab).
Features & Components 2 Figure 2 - 8 Audio Setup for Recording (Windows Vista) Right-click 2 - 12 Recording Audio
Features & Components Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, or from the VIA Audio Deck icon in the taskbar, or on the desktop (this will bring up the VIA Audio Deck menu). The volume may also be adjusted by means of the Fn + F5/F6 key combination. Click any of the buttons (e.g. ) on the left to expand the audio menu selections.
Features & Components 2 Parallel Printer After setting up the printer attach the parallel cable to the printer. Connect the printer’s parallel cable to the Parallel to USB converter, and then plug the converter into the USB port. Turn ON the printer, then turn ON the computer. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions. Adding a Printer The most commonly used peripheral is a printer.
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. 3 AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-in jack at the rear of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle.
Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Sleep/Hibernate hotkey button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options (Hardware and Sound menu) control panel in Windows Vista to configure this feature.
Power Management 3 Resuming Operation If the display is off the system can resume by pressing any key on the keyboard. The system can resume from Sleep mode by pressing the Sleep Button key combination (Fn + F4), or power button. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 1 Power Plan Advanced Settings 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance for maximum performance when the computer is powered from an AC power source.
Power Management 3 Sleep Button The Sleep Button in the Start Menu (not available in Classic View) can be used to send the computer into Sleep. Note that Sleep is the default power saving state in Windows Vista. System Power Options You can use the system power options to stop the computer’s operation and restart where you left off. The system features Sleep and Hibernate power saving states. Hibernate vs.
Power Management Sleep Sleep uses very little system power, and takes a short time to return to full operation. After an extended period of time in Sleep the computer will save the contents of system memory (e.g. any open documents and applications) to the hard disk and shut the system down. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep mode to save power.
Power Management 3 Password Protection It is recommended that you enable a password on wake up in order to protect your data. Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to either Sleep or Hibernate. In Sleep, the LED will blink green. In Hibernate the LED will be off (battery) or orange (AC/DC adapter). If the only the display is turned off, the LED will remain green.
Power Management Battery Information Please follow these simple guidelines to get the best use out of your battery. Low Battery Warning Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Advanced Settings (see Figure 3 - 1 on page 3 - 4). Click the battery icon status.
Power Management 3 Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display.
Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. 3 We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason see “Removing the Battery” on page 6 - 3. New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page 3 - 13 for instructions on how to do this).
Power Management Proper handling of the Battery Pack 3 Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 1. 2. 3. 3 Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options.
Power Management How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. 3 How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Power Management 3 3 - 16
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual CD-ROM and click Install Vista Drivers (button). 2. 4 If you wish to install the drivers manually see page 4 4. 3. Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below.
Drivers & Utilities Updating/Reinstalling Individual Drivers Driver Page # Video Page 4 - 5 Audio Page 4 - 5 Modem Page 4 - 6 LAN Page 4 - 6 CardReader Page 4 - 6 TouchPad Page 4 - 6 Hot Key Utility Page 4 - 7 Quick Button Utility (Only appears if no PC Camera module is installed Page 4 - 7 Wireless LAN Page 4 - 8 Bluetooth Page 4 - 8 1. PC Camera Page 4 - 8 2.
Drivers & Utilities Manual Driver Installation If you wish to install the drivers manually, click the Exit button to quit the Drivers Installer application, and then browse to the executable file in the location listed in the table below and follow the installation procedure for each driver. Note that X is the drive letter assigned to the CD/DVD-ROM drive. . 4 Driver Driver Location Video Vista 32bit: X:\Drivers\Video\setup.exe Audio Vista 32bit: X:\Drivers\Audio\SETUP.
Drivers & Utilities User Account Control (Win Vista) If a User Account Control prompt appears as part of the driver installation procedure, click Continue or Allow, and follow the installation procedure as directed. Windows Security Message If you receive a Windows security message as part of the driver installation process. Just click “Install this driver software anyway” or Install to continue the installation procedure.
Drivers & Utilities Modem 1. Click 3.Install Modem Driver > Yes. 2. Click OK. 3. The modem is ready for dial-up configuration. 4 Modem Country Selection Go to the Phone and Modem Options control panel (Hardware and Sound) and make sure the modem country selection is appropriate for you. LAN 1. Click 4.Install LAN Driver > Yes. 2. Click OK. 3. The network settings can mow be configured. 4 - 6 Driver Installation CardReader 1. Click 5.Install CardReader Driver > Yes. 2. Click Next > Next. 3.
Drivers & Utilities Hot Key Utility 1. Click 7.Install Hotkey Utility > Yes. 2. Click Next. 3. Click Finish to restart the computer. Adding/Removing a PC Camera Note that the Quick Button and PC Camera drivers cannot co-exist. Quick Button Utility If you do not have a PC Camera module installed, then the Quick Button Utility will appear in the Drivers Installer menu (only install the quick button driver if the PC Camera is not installed).
Drivers & Utilities Wireless LAN See the introduction in “802.11 b/g USB WLAN Module” on page 7 - 2, and check the installation procedure. 4 Bluetooth See the introduction in “Bluetooth Module” on page 7 - 7, and check the installation procedure. PC Camera See the introduction in “PC Camera Module” on page 7 - 12, and check the installation procedure.
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your system ever needs servicing.
BIOS Utilities Startup Screen Each time you turn on the computer, the system takes a few seconds to conduct tests on memory, keyboard, mouse and system. As the boot proceeds, you can click the mouse, or press Enter, and then choose “Launch System Setup” from the TrustedCore menu to access the PhoenixBIOS Setup Utility.
BIOS Utilities In addition to accessing the Setup menus, you can also select a boot device, view system information or setup a password for access to the computer at boot time (see overleaf).
BIOS Utilities Setting a Boot Password 1. Figure 5 - 3 Use the mouse to select Security Enrollment from the menu. A Security Enrollment screen similar to the screen below will then appear: Secu c rity t En Enrollm lment Security Enrollment Enter your new password and confirm r it. Adm d inistrator privileges 5 Password: New: Confirm r : Password Warning If you set a boot password NEVER forget your password. The consequences of this could be serious.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with four (4) menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu Figure 5 - 4 Main Menu PhoenixBIOS Setup Utility Main Main Advanced Boot Exit Item Specific Help 06 [22:11:05] [01/10/2007] System Time: System Date: 5 IDE Channel 0 Master IDE Channel 2 Master [TSSTcorpCD/DVDW TS-L632D-] [TOSHIBA MK8032GSX-(S1)] QuickBoot Mode: [Enabled] System Memory Extended Memory 633 KB 894 MB F1 Esc Help Exit Select Item Select Menu -/+ Enter , , or selects field.
BIOS Utilities IDE Channel 0/2 Master (Main Menu) Pressing Enter opens the sub-menu to show the configuration of either a DVD/CD Device or HDD on the computer’s IDE Channels. Use the Auto (Type:) setting to have the items configured automatically for you. QuickBoot Mode: (Main Menu) Enable this item to skip certain tests at start up, and thus decrease the time needed to boot the system. 5 System/Extended Memory: (Main Menu) This item contains information on the system memory, and is not user configurable.
BIOS Utilities Advanced Menu Figure 5 - 5 PhoenixBIOS Setup Utility Advanced Menu Main Advanced Advanced Boot Exit Item Specific Help Installed O/S: Legacy USB Support: Reset Configuration Data: Enable Multimedia Timer: Frame Buffer Size: 5 [WinXP/Vista] [Enabled] [No] [No] [128MB] Select the operating system installed on your system which you will use most commonly. Note: An incorrect setting can cause some operating systems to display unexpected behavior.
BIOS Utilities Legacy USB Support: (Advanced Menu) Choose “Enabled” if you intend to use USB devices in systems which do not normally support USB functionality (e.g. DOS). The default setting is “Enabled” and does not need to be changed if you intend to use your USB devices in Windows. Reset Configuration Data: (Advanced Menu) This item is set to No as default.
BIOS Utilities Boot Menu Figure 5 - 6 Boot Menu PhoenixBIOS Setup Utility Main Advanced Boot Exit Item Specific Help Boot priority order: 1: IDE 0: TSSTcorpCD/DVDW TS-L632D-( 2: IDE 1: 3: IDE 2: 4: IDE 4: TOSHIBA MK8032GSX-(S1) 5: USB FDC: 6: USB KEY: 7: USB HDD: 8: PCI BEV: VIA Boot Agent Excluded from boot order: : USB CDROM: : USB ZIP : USB LS120 : PCI SCSI 5 F1 Esc Help Exit Select Item Select Menu -/+ Enter Keys used to view or configure devices: Up and Down arrows select a device.
BIOS Utilities Exit Menu Figure 5 - 7 PhoenixBIOS Setup Utility Main Advanced Boot Exit Menu Exit Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Esc Help Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
BIOS Utilities 5 5 - 12
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. 4. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Slide the battery out in the direction of the arrow 3 .
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CD-ROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer 5. 6. 7. Lift the hard disk up in the direction of arrow 6 . Remove the screws 7 & 8 and cover 9 . Reverse the process to install a new hard disk drive.
Upgrading The Computer Upgrading the Optical (CD/DVD) Device 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery. Locate the hard disk bay cover and remove screws 1 - 3 . Remove the hard disk bay cover 4 . Remove the screw at point 5 , and use a screwdriver to carefully push out the optical device at point 6 . Reverse the process to install the new device. 5.
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 200 pin Small Outline Dual In-line (SODIMM) DDRII (DDR2) type memory modules (see “Memory” on page C - 2 for details of supported module types). The total memory size is automatically detected by the POST routine once you turn on your computer. 1. 2. Turn off the computer, and turn it over and remove the battery. Locate the CPU/RAM bay cover and remove screws 1 - 7 .
Upgrading The Computer 3. Remove the bay cover 8 . Figure 6 - 6 CPU/RAM Bay Cover Removed 8 6 Contact Warning Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. 4. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 9 & 10 ) in Figure 6 - 7.
Upgrading The Computer 5. The RAM module will 11 pop-up, and you can remove it. Figure 6 - 8 RAM Module Removal 11 6 6. 7. Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. 8. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit without much pressure. 9.
Upgrading The Computer Warranty The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 6 Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard.
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. • 802.11 b/g USB WLAN Module • Bluetooth Module • PC Camera Module Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + F11 key combination to toggle power to the WLAN module, and check the indicator to see if the module is powered on or not (see Table 1 - 2, on page 1 - 7/Table 1 - 4, on page 1 - 10). 802.11 b/g USB WLAN Module If you have included an 802.
Modules & Options Connecting to a Wireless Network Make sure the Wireless LAN module is turned on. 1. Click the taskbar wireless icon , and then click Connect to a network (or rightclick the icon , and then click Connect to a network). Figure 7 - 1 Taskbar Menus Click icon Right-click icon 2. 3. In the Show list, click to choose Wireless from the drop-down menu. A list of currently available networks will appear.
Modules & Options 4. 5. Click a network, and then click Connect. If you do not see a network you want to connect to, click Set up a connection or network (a list of options will appear allowing manual searching, and creating a new network). 6. Move the cursor over the taskbar icon Figure 7 - 3 Connecting 7 Figure 7 - 4 Connection Status 7 - 4 802.11 b/g USB WLAN Module to see the connection status (see below).
Modules & Options 7. To disconnect from the wireless network you can click the taskbar wireless icon , and then select Connect or disconnect to access the network menu, and click Disconnect (or right-click the icon , and then click Disconnect from). Click icon Security Enabled Networks You should try to make sure that any network you are connecting to is a secure network. Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Modules & Options Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center: 1. 2. 3. 7 Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Windows Mobility Center (Mobile PC). Click the button to Turn wireless off/on, or click the icon to access the network menu.
Modules & Options Bluetooth Module Before installing the Bluetooth driver, make sure that the optional Bluetooth module is on. Use the Fn + F12 key combination (see “Function Keys” on page 1 - 10) to toggle power to the Bluetooth module. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Bluetooth Driver Installation 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual CD-ROM into the CD/DVD drive. 2.
Modules & Options User Guides & Help View the BlueSoleil User Guides from the Help Menu (or press the F1 key) in the IVT Corporation BlueSoleil Main Window control panel. 7 Click the Help menu and select Contents and Index. Look through Getting Started or select the appropriate User Guide from the Contents menu.
Modules & Options PC Camera Module Before installing the PC Camera driver, make sure that the optional PC Camera is on. Use the Fn + F10 key combination (see “Function Keys” on page 1 - 10) to toggle power to the PC Camera module. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Latest PC Camera Driver Information Taking Still Pictures You can use the application button to take still pictures if you have installed the hot key driver.
Modules & Options 7 PC Camera Driver Installation 1. Make sure the module is powered on (click Cancel if you see a “New Hardware Found” message), and then insert the Device Drivers & Utilities + User’s Manual CD-ROM into the CD/DVD drive. 2. Click 10.Install Camera Driver > Yes. 3. Choose the language you prefer and click Next. 4. Click Next > Install. 5. Click Finish to restart the computer. 6.
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Recording (tab). Right-click Microphone (VIA High Definition Audio) and make sure the item is not disabled (if you wish to record from the internal microphone make sure that the Front Mic is not disabled). 5.
Modules & Options Figure 7 - 8 Audio Setup for PC Camera Right-click 7 7 - 12 PC Camera Module
Modules & Options BisonCap BisonCap is a video viewer useful for general purpose video viewing and testing, and can capture video files to .avi format. 1. 2. 3. 4. 5. Run the BisonCap application from the Start > Programs/All Programs > BisonCam menu, or by pressing the application button (it is recommended that you set the capture file before the capture process - see Set Capture File below).
Modules & Options Eliminating Screen Flicker If you find that the video screen in the BisonCap application is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3. Run the BisonCap program. Go to Options and scroll down to select “Video Capture Filter...”. Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Modules & Options PC Camera Hot Key Buttons You can use the PC Camera hot key buttons (the quick button utility must NOT be installed - see “Quick Button Utility” on page 4 - 7) to run the BisonCap program, to take still pictures and to zoom the camera in and out (if you have installed the hot key and PC Camera drivers - see “Hot Key Utility” on page 4 - 7 & “PC Camera Driver Installation” on page 7 - 13). 1. 2. 3. 4. 5. 6.
Modules & Options 7 7 - 16
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “LED Indicators” on page 1 - 7) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED power indicator , is blinking orange. Low Battery. Plug in the DC power source.
Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 14). Make sure you’re using the correct adapter.
Troubleshooting Problem Possible Cause - Solution You are experiencing screen flicker problems (in Windows Vista ONLY) when using an older CRT (Non DDC) as your external display You will need to update the video driver to support older CRTs. See “Non DDC CRT Monitors (for Win Vista Only)” on page B - 8 for instructions on installing the video driver. You forget password. If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help.
Troubleshooting Problem Possible Cause - Solution The CD/DVD cannot be read. The CD/DVD is dirty. Clean it with a CD/DVD cleaner kit. The CD/DVD tray will not open when there is a disc in the tray. The CD/DVD is not correctly placed in the tray. Gently try to remove the disc using the eject hole (see “Loading Discs” on page 2 - 3). The DVD regional codes can no longer be changed. The code has been changed the maximum 5 times. See “DVD Regional Codes” on page 2 - 5/ “DVD Regional Codes” on page D - 2.
Troubleshooting Problem Possible Cause - Solution The system never goes into a power saving mode. Power Options features are not enabled. Go to the Windows Power Options menu and enable the features you prefer (see “System Power Options” on page 3 - 6/“System Power Options” on page D - 22). Make sure you have enabled Hibernate mode from the control panel. The Wireless LAN/ Bluetooth modules cannot be detected. The modules are off.
Troubleshooting 8 8 - 12
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer. External Monitor (VGA) Port This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD.
Interface (Ports & Jacks) Item Description RJ-11 Modem Jack This port connects to the built-in modem. You may plug the telephone line directly into this RJ-11 telephone connection. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port. RJ-45 LAN Jack This port supports LAN (Network) functions. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port. Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot.
Interface (Ports & Jacks) A A - 4
VIA Video Driver Controls Appendix B: VIA Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 16. VIA Video Driver Installation Make sure you install all the drivers in the order indicated in Table 4 - 1, on page 4 - 6. Instructions for installing the video driver are repeated below. Video 1. Click 1.Install Video Driver > Yes. 2. Click Next > Next. 3. Click Finish to restart the computer.
VIA Video Driver Controls Function Key Combination You can use the Fn + F7 key combination to toggle through the display options: • Notebook Only • External Display Only • Notebook + External Display Make sure you give the displays enough time to refresh. Advanced Video Controls This section is about making adjustments for the LCD, and switching display devices. The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 15.
VIA Video Driver Controls Attaching Other Displays Besides the built-in LCD, you can also use an external monitor (CRT)/flat panel display as your display device. Connect it to the external monitor port on the right of the computer, and follow the instructions below: Windows Vista 1. 2. 3. Attach your external display to the external monitor port and turn it on.
VIA Video Driver Controls External displays may also be configured from S3Display tab in Advanced Display Settings: 1. 2. 3. 4. 5. 6. 7. Attach the external display to the external monitor port and turn it on. Click Advanced Settings in the Display Settings control panel (see “Video Features” on page 1 - 16) to display the additional tabs. Select S3Display (tab). Click to put a tick in the tickbox under the CRT icon. Click Apply > OK and allow the monitor time to refresh the display.
VIA Video Driver Controls Display Modes Single Display Only one of your attached displays is used. Mirrored This display mode simply shows an exact copy of the Primary display desktop on the Secondary display(s). Extended Desktop An Extended desktop allows the desktop to span the displays to act as a large work area, thus creating a lot more screen area for display. Each display device can be configured independently for specific resolutions and refresh rates.
VIA Video Driver Controls Using Windows Vista to Enable Extended Mode Display Settings Extended Desktop Use the control panel to drag the monitors to match the physical arrangement you wish to use. You can drag any icons or windows across to either display desktop, which makes it possible to have one program visible in one of the displays, and a different program visible in the other display. B Figure B - 3 New Display Detected B - 6 Display Modes 1. 2. 3. 4. 5.
VIA Video Driver Controls Using Display Settings to Enable Extended Mode 1. 2. 3. Attach your external display to the external monitor port, and turn it on. Open the Display Settings control panel (see “Video Features” on page 1 - 16). Click the monitor icon (e.g. 2 ), and make sure you have checked “Extend my Windows desktop onto this monitor.” and click Apply. Click the appropriate monitor icon (e.g. 2 ) to be able to select the option to extend the desktop on to it.
VIA Video Driver Controls Non DDC CRT Monitors (for Win Vista Only) If you are experiencing screen flicker problems (in Windows Vista ONLY) when using an older CRT (Non DDC) as your external display, you can install an updated driver to fix this problem. Follow the steps below: Uninstall the Original Driver 1. 2. 3. 4. Detach any connected external CRT. Go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Programs > Uninstall a program).
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, delayed or updated due to the manufacturer's release schedule. Check with your service center for details.
Specifications Feature Processor Specification Intel® Core™2 Duo Processor (478-pin) Micro-FC-PGA Package T7200/ T7400/ T7600 65nm (65 Nanometer) Process Technology 4MB On-die L2 Cache & 667MHz FSB 2.0/ 2.16/ 2.33 GHz Intel® Core™2 Duo Processor (478-pin) Micro-FC-PGA Package T5500/ T5600 65nm (65 Nanometer) Process Technology 2MB On-die L2 Cache & 667MHz FSB 1.66/ 1.
Specifications Feature Specification Video Adapter VIA VN896 Integrated Video System (Internal On Chip) Chrome 9HC™ Integrated 128bit 2D/3D Graphic Engine and Clock up to 250MHz Supports CRT Resolutions up to 2048 * 1536 at 75Hz Supports Microsoft DirectX 9.0 Security Security (Kensington® Type) Lock Slot BIOS Password BIOS One 4Mb Flash ROM Phoenix™ BIOS Storage One Changeable 12.7mm(h) Optical Device (CD/DVD) Type Drive (see “Optional” on page C - 5 for drive options) Easy Changeable 2.5" 9.
Specifications Feature C Specification Interface Three USB 2.0 Ports One RJ-11 Modem Jack One RJ-45 LAN Jack One DC-in Jack Card Reader Embedded 7-in-1 Card Reader (MS/ MS Pro/ SD/ Mini SD/ MMC/ RS MMC/ MS Duo) Note: MS Duo/ Mini SD/ RS MMC Cards require a PC adapter ExpressCard Slot One ExpressCard/34(54) Slot Communication AZALIA 56K Plug & Play Fax/Modem V.90/92 Compliant 10M/100Mb Base-T Ethernet LAN 802.11 b/g USB Wireless LAN Module (Option) USB (2.0) Bluetooth Module - Version 2.
Specifications Feature Specification Environmental Spec Temperature Operating: Non-Operating: Dimensions & Weight 360mm (w) * 267mm (d) * 25.4-34mm (h) 2.6 kg With 6 Cell Battery Optional Optical Drive Module Options: DVD/CD-RW Combo Drive Module DVD-Dual Drive Module 802.11 b/g USB Wireless LAN Module 5°C ~ 35°C -20°C ~ 60°C Relative Humidity Operating: Non-Operating: 20% ~ 80% 10% ~ 90% 300K or 1.3M Pixel USB PC Camera Module (Factory Option) USB (2.0) Bluetooth Module - Version 2.
Specifications C C - 6
Windows XP Information Appendix D: Windows XP Information This Appendix contains information (including control panel information, driver installation etc.) for users of the Windows XP OS.
Windows XP Information DVD Regional Codes Changing DVD Regional Codes Go to the Control Panel and double-click System > Hardware (tab), click Device Manager, then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialogue box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code. DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times.
Windows XP Information Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can customize the look of the Start menu by right-clicking the Start menu and selecting Properties from the menu.
Windows XP Information TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. Once you have installed the TouchPad driver (see “TouchPad” on page D - 34) you can configure the functions by double-clicking the TouchPad driver icon on the taskbar.
Windows XP Information Function Keys/Hot Keys The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key driver is installed (see “Hot Key Utility” on page D 34). After installing the driver an icon will appear in the taskbar.
Windows XP Information Application.exe You will need to locate the actual application executable (.exe) file, not just the shortcut. To find the application rightclick its shortcut on the desktop and click Properties. Click the shortcut (tab) and see where the executable file is located by clicking the Find Target (button).
Windows XP Information Recording Audio The audio record hot key button allows you to record audio from either the built-in microphone, or from a microphone connected to the microphone-in jack. To record on the computer, setup the audio recording options in Windows as follows (see Figure D - 5 on page D - 8). 1.
Windows XP Information Figure D - 5 Audio Setup for Recording (Windows XP) D D - 8 Recording Audio
Windows XP Information Audio Features You can configure the audio options on your computer from the Sounds and Audio Devices Windows control panel, or from the VIA Audio Deck icon in the taskbar, or on the desktop (this will bring up the VIA Audio Deck menu). The volume may also be adjusted by means of the Fn + F5/F6 key combination.
Windows XP Information Video Features You can switch display devices, and configure display options, from the Display Properties control panel in Windows as long as the video driver is installed. For further information see either “VIA Video Driver Controls” on page D - 12 (from pages D - 12 to D - 16). 1. 2. 3. Click Start, point to Settings and click Control Panel (or click Control Panel). Double-click Display (icon); Display (icon) is in the Appearances and Themes category.
Windows XP Information Advanced Video Controls This section is about making adjustments for the LCD, and switching display devices. Video Driver Controls The video interface lets you change the screen resolution and color output to whatever is most comfortable/efficient for you. This is a matter of hardware, video memory and the driver for your operating system.
Windows XP Information VIA Video Driver Controls VIA S3Tray Plus Utility The S3Tray Plus utility will appear in the taskbar when the video driver is installed. Click/Right-click the icon to bring up the menu below. From this menu you will also be able to make display adjustments, access the Display Properties control panel, check video memory information etc.
Windows XP Information VIA S3 Display Control Panels Right-click the S3Tray Plus utility in the taskbar to bring up the menu for the individual control panels, or access the menus from the Advanced tab in the Display Properties control panel. Help Menus Right-click on almost any item in the tabs to bring up the “What’s This?” button. Click the “What’s This?” button to bring up a help menu (if the item has a help menu associated with it).
Windows XP Information S3Tray Plus Utility You can also use the S3Tray Plus utility in the taskbar to configure an external display. Display Devices (VIA) Besides the built-in LCD, you can also use an external monitor (CRT)/flat panel display as your display device. Connect it to the external monitor port on the right of the computer. See the instructions below: Attach the external display (CRT) to the external monitor port. Right-click the icon in the taskbar and select S3Display.
Windows XP Information Display Modes (VIA) Single Display Only one of your attached displays is used. Playing DVD Videos Multiple Monitors This display mode simply shows an exact copy of the Primary display desktop on the Secondary display(s). Extended Desktop An Extended desktop allows the desktop to span the displays to act as a large work area, thus creating a lot more screen area for display. Each display device can be configured independently for specific resolutions and refresh rates.
Windows XP Information Display Settings Extended Desktop Use the control panel to drag the monitors to match the physical arrangement you wish to use. To Enable Extended Desktop (Display Properties) 1. Attach the external display to the external monitor port and turn it on. 2. Go to the Display Properties control panel (see “Video Features” on page D - 10) and click Settings (tab). 3. Click the monitor icon (e.g. 2 ), and click to put a tick in the “Extend my Windows desktop onto this monitor.
Windows XP Information Power Management Features To conserve power, especially when using the battery, your computer uses the ACPI power management system. Power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system. The Power Options control panel icon in Windows (see page D - 3) allows you to configure power management features for your computer.
Windows XP Information The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-in jack at the rear of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle.
Windows XP Information Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.
Windows XP Information Resuming Operation Press a key on the keyboard, or move the mouse/TouchPad to resume from Monitor or Hard Disk Stand by. Power Schemes You can set your computer to conserve power through individual components by means of Power Schemes.
Windows XP Information Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source.
Windows XP Information Stand by/Hibernate or Shutdown Error The computer may stop responding when you put it into (or resume from) Stand By or Hibernate, or when you shut down. D System Power Options You can use the system power options to stop the computer’s operation and restart where you left off.
Windows XP Information Stand by Stand by saves the least amount of power, but takes the shortest time to return to full operation. During Stand by the hard disk is turned off, and the CPU is made to idle at its slowest speed. All open applications are retained in memory. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Stand by mode to save power.
Windows XP Information Sleep Button You may also configure the Sleep/Resume key combination (Fn + F4) from the menu illustrated. In Windows this is referred to as the Sleep button. Configuring the Power Button The power button may be set to send the computer in to either Stand by or Hibernate mode. In Stand by mode, the LED will blink green. In Hibernate mode the LED will be off (battery) or orange (AC/DC adapter). If you are in a power saving mode set to save power through individual components (e.g.
Windows XP Information Battery Information Please follow these simple guidelines to get the best use out of your battery. Low Battery Warning New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page D - 28 for instructions on how to do this). Battery Life Your computer’s battery life is dependent upon many factors, including the programs you are running, and peripheral devices attached.
Windows XP Information Conserving Battery Power To conserve battery power: Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter. Close modem or communication applications when they are not being used. Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days.
Windows XP Information Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center.
Windows XP Information Battery FAQ Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions. How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery.
Windows XP Information Driver Installation The Device Drivers & Utilities + User’s Manual CDROM contains the drivers and utilities necessary for the proper operation of the computer. Table D - 3 lists what you need to install, and it is very important that the drivers are installed in the order indicated. Only install drivers for modules (WLAN, Bluetooth, and PC Camera) included in your purchase option.
Windows XP Information What to Install This section covers driver and utility installation instructions for Windows XP Home & Professional. Insert the Device Drivers & Utilities + User’s Manual CD-ROM, click Install WinXP Drivers (button) and then click the appropriate driver name from the Drivers Installer menu and then follow the instructions to install the driver. Alternatively Click Start and navigate (Browse..) to follow the manual setup instructions. 1. 2. 3.
Windows XP Information Updating/Reinstalling Individual Drivers If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and doubleclick the Add/Remove Programs item. If you see the individual driver listed (if not see below), uninstall it, following the on screen prompts (it may be necessary to restart the computer).
Windows XP Information New Hardware Found If you see the message “New Hardware Found” (Found New Hardware Wizard) during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure as directed. Driver Installation Procedure Note that X is the drive letter assigned to the CD/ DVD-ROM drive. D Chipset 1. Click 1.Install Chipset Driver > Yes. OR Click Start (menu) > Run... and navigate (Browse...
Windows XP Information Audio 1. Click 4.Install Audio Driver > Yes. OR Navigate (Browse...) to X:\Drivers\Audio\SETUP.EXE and click OK. 2. Click Next > Next > Next. 3. Click Finish to restart the computer. CardReader 1. Click 6.Install CardReader Driver > Yes. OR Click Start (menu) > Run... and navigate (Browse...) to X:\Drivers\Cardreader\Setup.exe and click OK. 2. Click Next > Next. 3. Click Finish to restart the computer. LAN 1. Click 5.Install LAN Driver > Yes. OR Click Start (menu) > Run...
Windows XP Information TouchPad 1. Click 7.Install TouchPad Driver > Yes. OR Click Start (menu) > Run... and navigate (Browse...) to X:\Drivers\Touchpad\Setup.exe and click OK. 2. Click Next > Next > Next (click Continue Anyway if asked if you want to continue at any time). 3. Click Finish to restart the computer.. D D - 34 What to Install Hot Key Utility 1. Click 8.Install Hotkey Utility > Yes. OR Click Start (menu) > Run... and navigate (Browse...) to X:\Drivers\Hotkey\Setup.EXE and click OK. 2.
Windows XP Information Quick Button Utility If you do not have a PC Camera module installed, then the Quick Button Utility will appear in the Drivers Installer menu (only install the quick button driver if the PC Camera is not installed). See Table 1 - 2, on page 1 - 7 and “Application Quick Buttons” on page D - 6 for details. 1. Click 11.Install Quick button Utility > Yes. OR Click Start (menu) > Run... and navigate (Browse..) to X:\Drivers\QButton\3AP.exe and click OK. 2. Click Next. 3.
Windows XP Information Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Use the Fn + F11 key combination to toggle power to the WLAN module, and check the indicator to see if the module is powered on or not (see Table 1 - 3, on page 1 - 8/ Table 1 - 4, on page 1 - 10). D 802.11 b/g USB WLAN Module If you have included an 802.
Windows XP Information Network Connection Use the Windows Network Connections control panel to access available wireless networks (Start > Settings > Network Connections or Start > Connect To > Show all Connections). Figure D - 18 Wireless Network Control Panels D 802.
Windows XP Information Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Use the Fn + F12 key combination to toggle power to the Bluetooth module, and check the indicator to see if the module is powered on or not (see Table 1 - 2, on page 1 - 7/ Table 1 - 4, on page 1 - 10).
Windows XP Information User Guide View the BlueSoleil User Guides (Contents and Index) from the Help menu (or press the F1 key) in the IVT Corporation BlueSoleil - Main Window control panel. Click BlueSoleil User Guides in the Contents tab, and click to select the appropriate User Guide from the panel on the right.
Windows XP Information Taking Still Pictures Double-click the My Computer icon on the desktop, or go the Start menu and point to My Computer, then click it. Double-click the BisonCam, NB Pro icon. PC Camera Module Before installing the PC Camera driver, make sure that the optional PC Camera is on. Use the Fn + F10 key combination (see “Function Keys” on page 1 - 10) to toggle power to the PC Camera module. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3.
Windows XP Information PC Camera Driver Installation 1. Make sure the module is powered on (click Cancel if you see a “New Hardware Found” message), and then insert the Device Drivers & Utilities + User’s Manual CD-ROM into the CD/DVD drive. 2. Click 11.Install Camera Driver > Yes. OR Click Start (menu) > Run... and navigate (Browse...) to X:\Drivers\Camera\Driver\Setup.exe and click OK. 3. Choose the language you prefer, and click OK. 4. Click Next > Finish to restart the computer. 5.
Windows XP Information PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows (see Figure D - 20 on page D - 43). 1. Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then doubleclick the Sounds & Audio Devices icon (Sounds, Speech, and Audio Devices in Category View). 2. Click Advanced in the Volume > Device volume tab. 3.
Windows XP Information Figure D - 20 Audio Setup (Windows XP) D PC Camera Module D - 43
Windows XP Information Pre-Allocating File Space You may pre-allocate the file size for the capture file in the BisonCap application. You can choose to ignore this by clicking Cancel. Pre-allocating space on the hard disk can improve the capture quality (particularly of large capture files), by reducing the amount of work the hard disk has to do in finding space for the video data as it is being captured. You may find it helpful to defragment the HDD before capture.
Windows XP Information Eliminating Screen Flicker If you find that the video screen in the BisonCap application is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3. Run the BisonCap program. Go to Options and scroll down to select “Video Capture Filter...”. Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Windows XP Information PC Camera Hot Key Buttons Snapshot Folder The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture using the application hot key button. If you accidentally delete or move the folder, you can create a new Snapshot folder on the desktop in order to capture the files.
