Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. • Only use a power adapter approved for use with this computer.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC adapter and cables. Stow them in the carrying bag. The AC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. • Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. • Position the display directly in front of you at a comfortable viewing distance. • Adjust the display-viewing angle to find the best position.
Preface Contents Notice ...........................................................................I FCC Statement .......................................................II Instructions for Care and Operation ..................... IV Power Safety ........................................................ VI Battery Precautions .............................................VII Cleaning ............................................................ VIII Servicing ..................................................
Preface 8 Channel Sound Support ...................................2-13 Adding a Printer .....................................................2-14 USB Printer ..........................................................2-14 Install Instructions: ..............................................2-14 Parallel Printer ......................................................2-14 Power Management Overview ..................................................................3-1 Advanced Configuration and Power Interface .
Preface Wireless LAN .....................................................4-12 Bluetooth .............................................................4-12 PC Camera ..........................................................4-12 BIOS Utilities Overview ..................................................................5-1 The Power-On Self Test (POST) .............................5-2 Failing the POST ....................................................5-3 Fatal Errors ........................................
Preface Intel PRO/Wireless 2915ABG WLAN Driver Installation .................................................7-4 Bluetooth Module .....................................................7-5 Bluetooth Driver Installation ................................7-5 PC Camera ................................................................7-7 PC Camera Driver Installation ..............................7-8 PC Camera Audio Setup .......................................7-8 AMCAP ..............................................
Preface Display Modes ......................................................... B-6 Clone Mode ........................................................... B-7 Extended Desktop Mode ....................................... B-8 Enabling TV Display ............................................. B-11 Intel Video Driver Controls Intel Video Driver Installation ................................ C-1 Dynamic Video Memory Technology ..................... C-2 Intel Graphics Properties ..................................
Preface XVIII
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 • Chapter 3 • Chapter 4 • Chapter 5 • Chapter 6 • Chapter 7 • Chapter 8 • Appendix A • Appendix B • Appendix C • Appendix D A guide to using the some of the main features of the computer e.g.
1 Quick Start Guide Model Differences This notebook series includes four different model types. The models differ in video support, system memory (RAM) supported, and AC adapter supplied. Models A & B include ATI X700 (ATI M26) PCI Express video cards, Models C & D include built-in Intel (Intel GMA 900) video (see “Video Features” on page 1 - 15). Models A & B are supplied with a 90W power adapter, Models C & D are supplied with a 65W power adapter.
Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the User’s Manual. You may also find the notes marked with a of interest to you.
1 Quick Start Guide Not Included Operating Systems (e.g. Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find this manual refers to the Microsoft Windows XP (Home & Professional Editions) operating system.
Quick Start Guide System Startup 1. 2. 3. 4. 5. 6. 7. 8. Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC adapter. Move the LCD latches 1 in the direction of the arrows to release the top cover.
1 Quick Start Guide System Map: Top View with LCD Panel Open 1. 2. 3. 4. 5. 6. 7. 8. 9. 1 Optional Built-In PC Camera LCD LED Power & Communication Indicators LED Status Indicators AP-Key Buttons Power Button Keyboard TouchPad and Buttons Speaker Wireless Device Operation Aboard Aircraft 2 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
Quick Start Guide LED Indicators The two sets of LED indicators (LED Power & Communication Indicators and LED Status Indicators) on the computer display helpful information about the current status of the computer.
1 Quick Start Guide AP-Key Buttons Keyboard These buttons give instant access to the default Internet browser and e-mail program, and toggle power to the optional module(s) (WLAN/Bluetooth/PC Camera). Make sure you install the driver to enable the APKey functions (refer to “What to Install” on page 4 1). The keyboard has an embedded numerical keypad for easy numeric data input (see Figure 1 - 3) and features Function Keys to allow you to change operational features instantly.
Quick Start Guide Function Keys To use the function keys, press and hold the Fn key, then press the appropriate function key (Esc - F10 etc.).
1 Quick Start Guide System Map: Front & Rear Views Figure 1 - 4 Front & Rear Views 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. LCD Latches Speaker Built-In Microphone Infrared Transceiver S/PDIF-Out Jack Microphone-In Jack Headphone-Out Jack Line-In Jack Vent/Fan Intake DC-In Jack Security Lock Slot Parallel Port 2 * USB 2.0 Ports 1 1 2 3 9 4 5 6 7 13 10 11 12 Overheating To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.
Quick Start Guide System Map: Left View Figure 1 - 5 Left View 1. 2. 3. 4. 5. 1 2 3 4 5 RJ-45 LAN Jack S-Video-Out Port External Monitor Port Mini-IEEE 1394 Port 2 * USB 2.0 Ports 5 Mini-IEEE 1394 Port External USB Hard Disk Drives The Mini-IEEE 1394 Port only supports SELF POWERED IEEE 1394 devices. If you are using an external USB HDD (or any USB device with a power rating of 500mA or above), make sure you use the power supply which comes with the device.
1 Quick Start Guide System Map: Right View Figure 1 - 6 - Right View 1. 2. 3. 4. 5. Optical Device Drive Bay (for CD/DVD Device - see page 2 - 3) PC Card Slot (see page 2 - 7) 3-in-1 Card Reader (reads SD/ MMC/ & MS formats - see page 2 - 6) RJ-11 Phone Jack Speaker 2 1 3 4 5 Changing DVD Regional Codes CD Emergency Eject If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole.
Quick Start Guide System Map: Bottom View Figure 1 - 7 - Bottom View CPU The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 1 3 1 2 6 4 1. 2. 3. 4. 5. 6. Overheating Vent/Fan Intake Modem/Bluetooth & Modem Combo Module Cover CPU Cover Hard Disk/Memory/WLAN (RAM) Cover Battery Cover Video Card Cover 5 To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.
1 Quick Start Guide Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can customize the look of the Start menu by right-clicking the Start menu and selecting Properties from the menu.
Quick Start Guide Video Features Your computer will have EITHER an ATI X700 (ATI M26) PCI Express video card (Model A & B computers), OR built-in Intel (Intel GMA 900) on-board video (Model C & D computers), depending on your purchase option (see “Video Adapter” on page D - 4). You can switch display devices, and configure display options, from the Display Properties control panel in Windows as long as the appropriate video driver is installed.
1 Quick Start Guide ATI Display Properties 1 2 3 Intel Display Properties 1 2 3 Figure 1 - 9 - Display Properties Desktop 1 - 16 Video Features
Quick Start Guide Display Devices & Options Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display or TV as your display device. A VGA monitor/Flat Panel Display connects to the external monitor port, a TV to the S-Video-Out Port. The following display modes are available (see “ATI Video Driver Controls” on page B - 1 or “Intel Video Driver Controls” on page C - 1 for details).
1 Quick Start Guide Power Management Features The Power Options control panel icon in Windows (see page 1 - 14) allows you to configure power management features for your computer. You may conserve power through individual components such as the monitor or hard disk (by means of Power Schemes), or you may use either Standby or Hibernate mode to conserve power throughout the system (enable Hibernate support from the control panel as pictured in Figure 1 - 10).
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • • • The Hard Disk Drive The Optical (CD/DVD) Device The 3-in-1 Card Reader The PC Card Slot The AutoMail Checker The TouchPad & Buttons/Mouse Audio Features Adding a Printer (general guidelines) Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Figure 2 - 1 Hard Disk Location Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.
Features & Components Optical Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page D - 4). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 12).
Features & Components 2 CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Disk Eject Warning Don’t try to remove a CD/DVD while the system is accessing it. This may cause the system to “crash”.
Features & Components DVD Regional Codes 2 To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - 12. .
Features & Components 3-in-1 Card Reader 2 The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. • MMC (MultiMedia Card) • SD (Secure Digital) • MS (Memory Stick) Card Reader Cover Make sure you keep the cover in the card reader when not is use. This will help prevent foreign objects and/or dust getting in to the card reader.
Features & Components PC Card Slot The computer is equipped with a PCMCIA 3.3V/5V slot for one type II PCMCIA CardBus PC Card Slot. Make sure you install the PCMCIA/Card Reader Card driver (see “What to Install” on page 4 - 1). Inserting and Removing PC Cards • Align the PC Card with the slot and push it in until it locks into place. • To remove a PC Card, simply press the eject button 1 next to the slot. 1 PC Card Slot Cover Make sure you keep the cover in the PC Card slot when not is use.
Features & Components Auto Mail Checker 2 After you have installed the driver for the Auto Mail Checker program (see “What to Install” on page 4 - 1) you may then configure it to give you notification when you receive new mail. You must be online to receive this notification (note that this program only supports the POP3 protocol), and your default mail program does not need to be open.
Features & Components You may then configure the options for your mailserver, name, password, program and method(s) of notification. Note Check with your Internet Service Provider, network administrator or Mail Service provider for details on what to put on these pages.
Features & Components 2 Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details. TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.
Features & Components Configuring the Infrared Settings for FIR To configure your computer for Fast Infrared (FIR) communication follow these steps: 1. 2. 3. 4. 5. 6. Click Start, point to Settings and click Control Panel (or just click Start > Control Panel). Double-click Wireless Link (Printers and Other Hardware Category) icon. Click Hardware (tab), and click the Properties button, then click the Advanced (tab). Select “Infrared Transceiver A” and change the Value to “HP HSDL2300/3600”. Click OK > OK.
Features & Components 2 Sound Volume Adjustment How high the sound volume can be set using the volume control knob depends on the setting of the volume control within Windows. Click the Speaker icon on the taskbar to check the setting.
Features & Components 8 Channel Sound Support 2 If you wish to configure your system for 8 channel sound support, then the following ports should be used as outputs.
Features & Components 2 Parallel Printer After setting up the printer attach the parallel cable to the printer. Connect the printer’s parallel cable to the Parallel port. Turn ON the printer, then the computer. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions. Adding a Printer The most commonly used peripheral is a printer.
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer uses the ACPI power management system. Power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management 3 Power Button as Standby or Hibernate Button If you are using a fully ACPI-compliant OS, (such as Windows XP) you can use the OS’s “Power Options” control panel to set the power button to send the system into Standby or Hibernate mode (see your OS’s documentation, or “Configuring the Power Button” on page 3 - 8 for details). The Power Sources The computer can be powered by either an AC adapter or a battery pack.
Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. Shutdown When the computer is on, you can use the power button as a Standby/Hibernate/Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.
Power Management 3 Resuming Operation The system can resume from Monitor or Hard Disk Standby by pressing a key on the keyboard. Figure 3 - 1 Power Schemes 3 - 4 Power Schemes Power Schemes You can set your computer to conserve power through individual components by means of Power Schemes.
Power Management Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source.
Power Management System Power Options 3 You can use the system power options to stop the computer’s operation and restart where you left off. This system features Standby and Hibernate sleep mode levels (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - Figure 3 - 2 on page 3 - 7). Hibernate Mode vs. Shutdown Hibernate mode and Shutdown are the same in that the system is off and you need to press the power button to turn it on.
Power Management Standby Standby saves the least amount of power, but takes the shortest time to return to full operation. During Standby the hard disk is turned off, and the CPU is made to idle at its slowest speed. All open applications are retained in memory. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Standby mode to save power.
Power Management Configuring the Power Button The power button may be set to send the computer in to either Standby or Hibernate mode (Figure 3 - 3). In Standby mode, the LED will flash green. In Hibernate mode the LED will be off. If you are in a power saving mode set to save power through individual components (e.g. hard disk, monitor), the LED will remain green.
Power Management Battery Information Please follow these simple guidelines to get the best use out of your battery. Low Battery Warning New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page 3 - 12 for instructions on how to do this). Battery Life Your computer’s battery life is dependent upon many factors, including the programs you are running, and peripheral devices attached.
Power Management 3 Conserving Battery Power To conserve battery power: Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC adapter. Close modem or communication applications when they are not being used. Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days.
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center.
Power Management 3 Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions. Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Navigate (Browse..) to D: 4 You will notice that many of the instructions for driver installation require you to “Navigate (Browse) to D:”. We assume that you will install all drivers and utilities from the built-in CD device and it is assigned to “Drive D:”. In addition, all file extensions can be seen In this case “D:” is the drive specified for your CD device. Not all computers are setup the same way, and some computers have the CD listed under a different drive letter - e.g.
Drivers & Utilities Service Packs Check the warnings on the following pages regarding installation of the appropriate Service Pack for your Windows OS. Make sure you have installed the appropriate Service Pack before installing all the drivers. Service Pack Installed To see which Service Pack is currently installed on your computer go to the General tab of the System control panel. Right-click the My Computer icon on the desktop or in the Start menu and select Properties.
Drivers & Utilities Authorized Driver Message 4 If you receive a message telling you that the driver you are installing is not authorized (Digital Signature Not Found), just click Yes or Continue Anyway to ignore the message and continue the installation procedure. You will receive this message in cases where the driver has been released after the version of Windows you are currently using. All the drivers provided will have already received certification for Windows.
Drivers & Utilities Driver Installation Insert the Device Drivers & Utilities + User’s Manual CD-ROM and the NoteBook Driver Installation application will run automatically. If you want to install the driver manually see “Manual Driver Installation” on page 4 - 7. NoteBook Driver Installation Application 1. 2. 3. 4. 5. 6.
Drivers & Utilities 4 Feature Windows XP (SP2) Service Pack Install Service Pack 2 on your system if not included in your Windows version Chipset Page 4 - 8 Audio Page 4 - 8 Modem Page 4 - 9 Network (LAN) Page 4 - 9 Video (see “ATI Video Driver Installation” on page B - 1) (see “Intel Video Driver Installation” on page C - 1) Ap-Key Page 4 - 10 TouchPad Page 4 - 11 PCMCIA/Card Reader Page 4 - 11 AutoMail Page 4 - 12 Wireless LAN See the install procedure on pages 7 - 3 & 7 - 4 Blue
Drivers & Utilities Manual Driver Installation Driver Installation Procedure If you wish to install the drivers manually, click the Exit button to quit the NoteBook Driver Installation application, then follow the manual installation procedure for each driver. The manual installation procedure begins with instructions on how to browse to the executable file; “Click Start (menu) > Run..”. This section covers driver and utility installation instructions for Windows XP Home & Professional.
Drivers & Utilities 4 Chipset 1. Double-click Chipset from the NoteBook Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\ 00Chipset\setup.exe and click OK. 2. Click Next > Yes > Next. 3. Click Finish to restart the computer. 4 - 8 Driver Installation Audio 1. Double-click AUDIO from the NoteBook Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\ 01Audio\Setup.exe and click OK. 2.
Drivers & Utilities Modem 1. Double-click MODEM from the NoteBook Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\ 02Modem\Setup.exe and click OK. 2. Click (button). 3. Click (button). 4. The modem is ready for dial-up configuration. LAN 1. Double-click LAN from the NoteBook Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\ 03Lan\Setup.exe and click OK. 2. Click Next. 3.
Drivers & Utilities Video The installation of the video driver will depend on your video system: 4 For ATI PCI Express video cards (Models A & B only) see “ATI Video Driver Installation” on page B - 1. For Intel on-board video (Models C & D only) see “Intel Video Driver Installation” on page C - 1. 4 - 10 Driver Installation AP-Key 1. Double-click AP-Key from the NoteBook Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\ 05Ap-key\Setup.exe and click OK. 2.
Drivers & Utilities TouchPad 1. Double-click TouchPad from the NoteBook Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\ 06Touchpad\SETUP.EXE and click OK. 2. Click Next > Next. 3. If you wish to view the Readme file select Yes and click Next, otherwise select No and click Next. 4. Click Finish to restart your computer (Click Yes/Continue Anyway if asked if you want to continue). 5.
Drivers & Utilities 4 AutoMail 1. Double-click AutoMail from the NoteBook Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\ 11Automail\SETUP.exe and click OK. 2. To continue click Next > Next > Finish. 3. Click Start > Turn Off Computer > Restart to restart the computer. 4. The program will run upon startup. 5. For further details see “Auto Mail Checker” on page 2 - 8.
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make.
BIOS Utilities POST Screen 5 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST Note: The POST screen as pictured is for guideline purposes only. The POST screen on your computer may appear slightly different. The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory). As the POST proceeds, the computer will tell you if there is anything wrong.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “non-fatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities The Setup Program The Phoenix Setup program tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup 5 To enter Setup, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen in Figure 5.1 is usually present for a few seconds after you turn on the system. If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with five (5) menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu PhoenixBIOS Setup Utility Figure 5 - 2 Main Main Advanced Security Boot Exit Main Menu Item Specific Help System Time: 13 [22:11:05] [09/22/2004] System Date: , , or selects field. 5 IDE Channel 0 Master IDE Channel 0 Slave SATA Port 1 [20004MB] [CD-ROM] [None] System Memory Extended Memory 640 MB 522240 KB VGA BIOS Revision 009.008.001.
BIOS Utilities IDE Channel 0 Master/Slave (Main Menu) Pressing Enter under opens the sub-menu to show the configuration of the either a CD Device or HDD that on the computer’s IDE Channels 0 or 1. Use the Auto (Type:) setting to have the items configured automatically for you. SATA Port 1 (Main Menu) Pressing Enter under opens the sub-menu to show the configuration of the SATA Port 1. Use the Auto (Type:) setting to have the items configured automatically for you.
BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu PhoenixBIOS Setup Utility Advanced Advanced Main Security Power Boot Exit Item Specific Help Advanced Chipset Control Select options for Advanced Chipset features.
BIOS Utilities National 383 SIO Control Sub-Menu (Advanced Menu) Pressing Enter here will provide a sub-menu that controls the configuration of various National 383 SIO devices. Legacy USB Support (Advanced Menu) Use this menu item to enable/disable the support for Legacy Universal Serial Bus. 5 Boot-time Diagnostic Screen (Advanced Menu) Use this menu item to enable/disable the display on the boot-time Diagnostic Screen. Reset Configuration Data (Advanced Menu) This item is set to No as default.
BIOS Utilities Security Menu Figure 5 - 4 Security Menu PhoenixBIOS Setup Utility Main Advanced Security Security Boot Exit Item Specific Help 5 Supervisor Password Is: Clear Set Supervisor Password Password on boot: Enter] [E [Disabled] Fixed disk boot sector: [Normal] Supervisor Password controls access to the setup utility. Security Menu The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on.
BIOS Utilities Password on boot: (Security Menu) Specify whether or not a password (supervisor or user password) should be entered to boot the computer. If “Enabled” is selected, only users who enter a correct password can boot the system (see the warning in the sidebar). The default setting is “Disabled”. Note: To clear existing passwords press Enter and type the existing password, then press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance.
BIOS Utilities Boot Menu PhoenixBIOS Setup Utility Figure 5 - 5 Boot Menu Main Advanced Security Boot Exit Item Specific Help 5 Boot priority order: 1: IDE 0: FUJITSU MHT2020AT-(PM) 2: IDE 1: TSSTcorpCD/DVDW TS-L532A 3: IDE 2: 4: USB FDC: 5: PCI LAN: B2 D0 Yukon PXE IDE 0/2 channel IDE channel 0 is for parallel hard disks, and IDE channel 2 is for serial hard disks.
BIOS Utilities Boot devices usually are hard drives, floppy drives, and CD-ROMs/DVDROMs and Networks (LANs). When you specify a device as a boot device on the Boot Menu, it requires the availability of an operating system on that device. Most home computers come with an operating system already installed on “Drive C:”. 5 If you wish to boot from a CD-ROM/DVD-ROM you will need to add it to the boot order. As a general rule the order below is recommended: 1. 2. 3. 4.
BIOS Utilities Exit Menu Figure 5 - 6 Exit Menu PhoenixBIOS Setup Utility Main Advanced Security Boot Exit Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes 5 F1 Esc Help Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. When Not to Upgrade These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. The battery 2 will pop up to allow you to lift it out of the bay as indicated. Warranty Warning Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty.
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CDROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer 1. 2. 3. Turn off the computer, and turn it over and remove the battery. Locate the hard disk/memory bay cover and remove screws 1 Remove the bay cover 5 . - 4 .
Upgrading The Computer 4. 5. 6. 7. Pull the tab 6 in the direction of the arrow 7 in order to release the disk assembly from the connector. Lift the hard disk assembly 8 up out off the computer. Remove screws from points 9 - 12 on the side of the hard disk assembly in order to separate the bracket from the hard disk 13 . Reverse the process to install a new hard disk(s).
Upgrading The Computer Changing Serial and Parallel Hard Disk Cables The system can support either serial (SATA) OR parallel (PATA) hard disks, however different cables are used to support each hard disk type. If you are changing hard disk types then you will be required to change the cable. 1. 2. 3. 4. 5. 6. Remove the hard disk assembly (see page 6 - 4). Remove screws 1 & 2 . Carefully remove the cable 3 . Remove any cable protector 4 from the new cable.
Upgrading The Computer RAM Modules Supported 6 If you intend to upgrade or replace your memory (RAM) modules, make sure you are using the appropriate module type for your computer. Model A & C computers support DDR RAM modules; Model B & D computers support DDR2 (DDR2) RAM modules. These types of RAM modules are not interchangeable, and they differ in size very slightly. If you are unsure which module type your computer supports then consult your service center.
Upgrading The Computer 1. 2. 3. Turn off the computer, and turn it over and remove the battery. Locate the hard disk/memory bay cover and remove screws 1 Remove the bay cover 5 . - 4 .
Upgrading The Computer 4. Gently pull the two release latches ( 6 & 7 ) on the sides of the memory socket in the direction indicated by the arrows in Figure 6 - 7. Contact Warning 6 Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. Figure 6 - 7 RAM Module Removal 6 7 6 7 8 8 5. 6. 7. The RAM module 8 will pop-up, and you can remove it.
Upgrading The Computer Upgrading the Optical (CD/DVD) Device 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery. Locate the hard disk/memory bay cover and remove screws 1 - 5 . Remove the bay cover 6 . Use a screwdriver to carefully push the optical device 7 out of the computer at point 8 .
Upgrading The Computer Warranty The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 6 Unauthorized tampering with the HDD may also violate your warranty. 6 - 12 Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative.
Modules Chapter 7: Modules Overview This chapter contains the information on the WLAN, Bluetooth, and PC Camera modules which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. The chapter includes information on the following: 7 • Intel PRO/Wireless 2200BG (802.11b/g)/ 2915ABG (802.
Modules Wireless Device Operation Aboard Aircraft 7 Intel PRO/Wireless Mini-PCI WLAN Module Either an Intel PRO/Wireless 2200BG (802.11b/g) or 2915ABG (802.11a/ b/g) Mini-PCI WLAN module is supplied as a standard feature for the computer. You will have the appropriate software CD provided for your module. The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
Modules Intel PRO/Wireless 2200BG WLAN Driver Installation 1. Make sure the module is powered on, then insert the Intel PROSet/ Wireless CD-ROM into the CD drive. 2. Click Install Software (button). 3. Click the button to accept the license and click Next > Next > OK. 4. Click OK to complete the installation. 5. You can configure the settings by going to the Intel (R) PROSet Wireless control panel (Start > Programs > Intel PROSet Wireless), or by clicking the icon in the taskbar.
Modules Intel PRO/Wireless 2915ABG WLAN Driver Installation 1. Make sure the module is powered on, then insert the Intel PROSet/ Wireless CD-ROM into the CD drive. 2. Click Install Software (button). 3. Click the button to accept the license and click Next > Next > OK. 4. Click OK to complete the installation. 5. You can configure the settings by going to the Intel (R) PROSet Wireless control panel (Start > Programs > Intel PROSet Wireless), or by clicking the icon in the taskbar.
Modules Bluetooth Module Before installing the Bluetooth driver, make sure that the optional Bluetooth module is on. Use the Bluetooth AP-Key button to toggle power to the Bluetooth module . Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 6. Bluetooth Driver Installation 1. Insert the Bluetooth CD-ROM into the CD/DVD drive. 2. The program will run automatically. 3. Click Install (button). 4. Click the button to accept the license agreement, then click OK. 5.
Modules Figure 7 - 2 Bluetooth Control Panels/ Help 7 7 - 6 Bluetooth Module
Modules PC Camera If you have purchased the optional PC Camera you will need to install the device driver for it as indicated on the following pages (make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 6). Before installing the Camera driver, make sure that the optional Camera module is on (the LED will be green). Use the Camera AP-Key Button (see “AP-Key Buttons” on page 1 - 8) to toggle power to the PC Camera module.
Modules PC Camera Driver Installation 1. Insert the PC Camera CD-ROM into the drive. 2. Click Next. 3. Click Finish to restart the computer. 4. After restart the computer will find the new hardware for you. 5. Run the AMCAP program from the CMM PC Camera item in the Start > Programs/All Programs menu. PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 7 1. 2. 3. 4. 5. 6.
Modules Figure 7 - 3 Audio Setup 7 PC Camera 7 - 9
Modules Pre-Allocating File Space AMCAP AMCAP is a video viewer useful for general purpose video viewing and testing, and can capture video files to .avi format. 1. You may pre-allocate the file size for the capture file in the AMCAP program. You can choose to ignore this by clicking Cancel.
Modules Eliminating Screen Flicker If you find that the video screen in the AMCAP program is flickering, you can try to adjust the option from the Video Capture Filter options. 1. 2. 3. Run the AMCAP program from the Start > Programs/All Programs > CMM PC Camera menu. Go to Options and scroll down to select “Video Capture Filter...”. You can choose either 50Hz or 60Hz from the No Flicker box.
Modules 7 7 - 12
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power Indicators (see “LED Indicators” on page 1 - 7) to see the computer’s power status. • Connections - Check all the cables to make sure that there are no loose connections anywhere.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Power Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The Battery LED power indicator , is blinking orange. Low Battery. Plug in the AC power source.
Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 13). Make sure you’re using the correct adapter.
Troubleshooting Display Problem Nothing screen. appears Possible Cause - Solution on The system is in a power saving mode. Toggle the sleep/resume key combination, Fn + Esc (see “Sleep Button” on page 3 - 8). \ The screen controls need to be adjusted. Toggle the screen control key combinations Fn + F8/F9. If you’re connected to an external monitor, make sure it’s plugged in and turned on. You should also check the monitor’s own brightness and contrast controls.
Troubleshooting Boot Password Problem You forget password. the Possible Cause - Solution boot If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning 8 If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Audio & CD Device Problem Possible Cause - Solution The sound cannot be heard or the volume is very low. The volume might be set too low. Check the volume control in the Volume Control Panel in the Windows taskbar, or use the key combination Fn + F5 and F6 (see “Audio Features” on page 2 - 12) to adjust. The compact disc cannot be read. The compact disc is dirty. Clean it with a CD-ROM cleaner kit. The compact disc tray will not open when there is a disc in the tray.
Troubleshooting Keyboard Problem Unwelcome numbers appear when typing. Possible Cause - Solution If the LED is lit, then Num Lock is turned ON. (see “LED Indicators” on page 1 - 7). Other Keyboards 8 If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work.
Troubleshooting Operation Problem Possible Cause - Solution The system freezes or the screen goes dark. The system’s power saving features have timed-out. Use the AC adapter, press a key on the keyboard, or press the sleep (Fn + Esc) key combination, or press the power button if no LEDs are lit. The system never goes into a power saving mode. Power Options features are not enabled. Go to the Windows Power Options menu and enable the features you prefer (see “System Power Options” on page 3 - 6).
Troubleshooting Modules Problem Possible Cause - Solution The Wireless LAN/ Bluetooth/ PC Camera modules cannot be detected. The modules are off. Check the LED indicators to see if the modules are on or off (see “LED Indicators” on page 1 - 7). If the LED indicator is off, then press the AP-Key combination in order to enable the modules (see “AP-Key Buttons” on page 1 - 8). The Wireless LAN/ Bluetooth/ PC Camera modules cannot be configured. The driver(s) for the module(s) have not been installed.
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Ports and Jacks Item Built-In Microphone Card Reader Port DC-In Jack Description The built-in microphone allows you to record on your computer The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. Plug the supplied AC adapter into this jack to power your computer.
Interface (Ports & Jacks) Item Description Microphone-In Jack Plug an external microphone in to this jack to record on your computer. Mini-IEEE 1394 Port This port allows a high-speed connection to various peripheral devices, e.g. external disk drives and digital cameras (see note below). Mini-IEEE 1394 Port The Mini-IEEE 1394 port only supports SELF POWERED IEEE 1394 devices. Parallel Port RJ-11 Phone Jack RJ-45 LAN Jack Connect a parallel type printer to this port.
Interface (Ports & Jacks) Item Description Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. S/PDIF-Out Jack This S/PDIF (Sony/Philips Digital Interface Format) Out Jack allows you to connect your DVD-capable PC to a Dolby AC-3 compatible receiver for “5.1” or ‘dts’ surround sound. S-Video-Out Port Connect your television to your computer and view DVDs, VCDs or anything else your computer can display.
ATI Video Driver Controls Appendix B: ATI Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 15. ATI Video Driver Installation Make sure you install the drivers in the order indicated in Table 4 - 1 on page 4 - 6. Only Model A & B computers support ATI PCI Express video cards. 1. Double-click VGA from the Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\04VgaM26\Setup.exe and click OK. 2.
ATI Video Driver Controls ATI Taskbar Icon You can also access ATI Mobility Radeon X700 Properties by right-clicking the ATI icon in the taskbar. Point to Settings and click ATI Display Settings, then click the Settings (tab). ATI Mobility Radeon Properties More advanced video configuration options are provided in the ATI Mobility Radeon X700 control panel tab: 1. 2. 3. 4. Open the Display Properties (see “Video Features” on page 1 - 15) control panel. Click Advanced (button).
ATI Video Driver Controls Figure B - 2 ATI Mobility Radeon X700 Properties Tabs Help Menus Right-click on almost any item in the tabs to bring up the “What’s This?” button. Help Menu Click to Configure Theater Mode Click the “What’s This?” button to bring up the help menu.
ATI Video Driver Controls Theater Mode Theater Mode can be enabled by clicking Clone Mode Options (button) in the Overlay tab from the ATI Mobility Radeon X700 Properties. (see page B 3). Theater Mode enables you to display video playback in full screen on a secondary monitor. B B - 4 Display Devices Display Devices Besides the built-in LCD, you can also use an external monitor/flat panel display or TV as your display device. The following are the display options: 1. 2. 3. 4. The built-in LCD.
ATI Video Driver Controls Attaching Other Displays If you prefer to use a monitor or flat panel display, connect it to the external monitor port on the left of the computer. 1. 2. 3. 4. 5. Attach your external monitor to the external monitor port (or TV to the SVideo-Out Port), and turn it on. Select the Displays tab in the ATI Mobility Radeon X700 properties. Click the enable/disable button / for the display device you wish to use. Click Apply. Click Yes to accept the settings and OK to save the changes.
ATI Video Driver Controls Primary & Clone Displays The Primary display in an Extended Desktop environment will be associated with display Icon 1 in the settings tab. The Clone display will set the associated display to show a copy of the Primary desktop. B The Clone display in an Extended Desktop environment will show the portion of the desktop extended from the Primary display. B - 6 Display Modes Display Modes Single Only one of your attached displays is used.
ATI Video Driver Controls Clone Mode Clone Mode simply shows an exact copy of the Primary display desktop on the other display(s). This mode will drive multiple displays with the same content. Use this feature to display the screen through a projector for a presentation. Each display device can be configured independently as this allows you to set the options for overhead projectors etc., which require specific resolutions and refresh rates.
ATI Video Driver Controls Extended Desktop Mode The system supports Extended Desktop in multiple display environments in WindowsXP. An Extended Desktop creates a desktop spanning multiple displays and acts as a large workspace. To get this effect: 1. 2. 3. 4. 5. 6. 7. 8. 9. B B - 8 Display Modes Attach your external monitor to the external monitor port (or TV to the SVideo-Out Port), and turn it on. Select the Displays tab in the ATI Mobility Radeon X700 properties.
ATI Video Driver Controls 10. In the example shown in Figure B - 5 the primary monitor 1 is on the left, the other display is on the right. Help Click either the Display popup menu, or click the icon for the appropriate display. Then click the tick box to extend the primary display’s desktop to it. Further help is available through the menus accessed from the taskbar (see Figure B - 1 on page B 2). Figure B - 5 Extended Desktop Monitor Arrangement 11.
ATI Video Driver Controls 12. One display will be set to 1 (Primary). The displays may be switched as long as one as set to Primary. Figure B - 6 Displays Tab (Extended Desktop Mode) In this picture the notebook LCD panel is the primary display, and the desktop may be extended to any attached displays. The primary display is indicated with a button depressed. Click the buttons to switch the primary display. 13.
ATI Video Driver Controls Enabling TV Display To display desktop images on a TV, connect the TV to your computer by using an S-Video cable from the TV to the S-Video-Out Port on the left side of the computer (see “System Map: Left View” on page 1 - 11). Further help is available to help you troubleshoot your TV connection through the menus accessed from the taskbar (see page Figure B - 1 on page B - 2).
ATI Video Driver Controls B B - 12
Intel Video Driver Controls Appendix C: Intel Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 15. Intel Video Driver Installation Make sure you install the drivers in the order indicated in Table 4 - 1 on page 4 - 6. Only Model C & D computers support Intel on-board video. 1. Double-click VGA from the Driver Installation menu. OR Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\04igd\Setup.exe and click OK. 2.
Intel Video Driver Controls DVMT Notes DVMT is not user-configurable. DVMT is not local video memory. DVMT will not function in MS-DOS. DOS uses the legacy memory indicated. Figure C - 1 DVMT Memory Requirements Dynamic Video Memory Technology Intel® DVMT automatically and dynamically allocates as much (up to 224MB) system memory (RAM) as needed to the video system (the video driver must be installed - see page C - 1). DVMT returns whatever memory is no longer needed to the operating system.
Intel Video Driver Controls Intel Graphics Properties More advanced video configuration options are provided by the Intel(R) Graphics Media Accelerator Driver. 1. 2. 3. Open Display Properties (see “Video Features” on page 1 - 15). Click the Intel(R)... tab and click Graphics Properties (button). You can also access Graphics Properties from the Windows Intel(R) GMA Driver for Mobile control panel. Taskbar Icon You can also access the controller properties from the taskbar.
Intel Video Driver Controls Intel Graphics Properties Note that the Graphics Properties control panel is entitled Mobile Intel(R) 915GM/GMS, 910GML Express Chipset Family. You may make changes to the Devices, Color, Schemes, Hot Keys by clicking the appropriate tab and adjusting the setting, then clicking OK.
Intel Video Driver Controls Schemes Use Schemes to configure quick settings for applications which require specific resolution and color settings in order to run properly e.g. games, multimedia programs. To set the schemes: 1. 2. 3. 4. 5. 6. 7. 8. Go to the Graphics Properties control panel (see “Intel Graphics Properties” on page C - 3). Configure your display configuration, resolution etc. as per your requirements, from Devices (tab). Click on Schemes (tab).
Intel Video Driver Controls Function Key Combination You can use the Fn + F7 key combination to toggle through the display options: • Notebook Only • External Display Only • Notebook + External Display Make sure you give the displays enough time to refresh. C C - 6 Display Devices Display Devices Besides the built-in LCD, you can also use an external monitor/flat panel display or TV as your display device. The following are the display options: 1. 2. 3. 4. The built-in LCD.
Intel Video Driver Controls Attaching Other Displays If you prefer to use a monitor or flat panel display, connect it to the external monitor port on the left of the computer. 1. 2. 3. 4. 5. Attach your external monitor to the external monitor port (or TV to the SVideo-Out Port), and turn it on. Go to the Graphics Properties control panel (see “Intel Graphics Properties” on page C - 3) and click Devices (tab). Choose the display option from the list on the left.
Intel Video Driver Controls Function Key Combination You can use the Fn + F7 key combination to toggle through the display options: • Notebook Only • External Display Only • Notebook + External Display Make sure you give the displays enough time to refresh. Note the “Television Display Warning” on page C - 6. C C - 8 Display Modes Display Modes Single Display Only one of your attached displays is used. Intel(R) Dual Display Clone This mode will drive multiple displays with the same content.
Intel Video Driver Controls To Enable Intel(R) Dual Display Clone Mode 1. 2. 3. 4. 5. 6. Attach your external monitor to the external monitor port (or TV to the SVideo-Out Port), and turn it on. Go to the Graphics Properties control panel (see “Intel Graphics Properties” on page C - 3) and click Devices (tab). Click Intel(R) Dual Display Clone (icon). Choose which attached device will be Primary or Secondary. Adjust the settings by clicking the Display Settings (tab) if necessary.
Intel Video Driver Controls Display Settings Extended Desktop You can have different Colors, Screen Area and Monitor Refresh Rates for each display device provided your monitor can support them. You can drag the monitor icons to match the physical layout of your displays. Icons and programs may also be dragged between the displays. To Enable Extended Desktop Mode: 1. 2. 3. 4. 5. 6. Attach your external monitor to the external monitor port (or TV to the SVideo-Out Port), and turn it on.
Intel Video Driver Controls To Enable Extended Desktop (Display Properties) 1. 2. 3. 4. 5. Attach your external monitor to the external monitor port (or TV to the SVideo-Out Port), and turn it on. Click Start, point to Settings (or click Control Panel) and click Control Panel (if you are in Category View choose Appearance and Themes). Double-click Display (icon). In the Display Properties dialog box, click Settings (tab). Click the monitor icon (e.g.
Intel Video Driver Controls Function Key Combination You can use the Fn + F7 key combination to toggle through the display options: • Notebook Only • External Display Only • Notebook + External Display Make sure you give the displays enough time to refresh. Note the “Television Display Warning” on page C - 6. C Figure C - 8 TV Display Settings C - 12 TV Settings TV Settings If you are using a TV as a display device you may adjust the settings as follows: 1. 2. 3. 4. 5. 6.
Specifications Appendix D: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/speeds and CD/DVD device types) may be changed or updated due to the manufacturer's release schedule. Check with your service center for details.
Specifications Feature Processor Core Logic Specification Intel Pentium® M Processor (478-pin) Micro-FC-PGA Package Models 730/ 740/ 750/ 760/ 770 (µ0.09) 0.09 Micron Process Technology 2MB On-die L2 Cache & 533MHz FSB 1.6/ 1.73/ 1.86/ 2/ 2.13 GHz Intel Pentium® M Processor (478-pin) Micro-FCPGA Package (µ0.13) 0.13 Micron Process Technology 1MB On-die L2 Cache & 400MHz FSB 1.3/ 1.4/ 1.5/ 1.6/ 1.7 GHz Intel Pentium® M Processor (478-pin) Micro-FC-PGA Package Models 725/ 735/ 745/ 755 (µ0.09) 0.
Specifications Feature Memory Specification Models A & C: Two SO-DIMM Sockets Supporting DDR Memory Single Channel Speed up to 333 MHz (Note: Do Not Use Other Module Types) Memory Expandable up to 2GB (128/ 256/ 512/ 1024 MB DDR Modules) Models B & D: Two SO-DIMM Sockets Supporting DDRII (DDR2) Memory Dual Channel Speed up to 533 MHz (Note: Do Not Use Other Module Types) Memory Expandable up to 2GB (128/ 256/ 512/ 1024 MB DDR Modules) RAM Modules Supported If you intend to upgrade or replace your memor
Specifications Feature D Specification Video Adapter Models A & B: ATI M26(X700) PCI-E 16X 128MB/256MB(M26) DDR-DRAM Pure Hardware DirectX 9 128-bit Memory Interface Storage One Changeable 12.7mm(h) Optical Device (CD/DVD) Type Drive (see “Optional” on page C 6 for drive options) Easy Changeable 2.5" 9.5 mm (h) IDE HDD Supports PATA (Parallel) / SATA (Serial) HDDs. Supporting ATA 100/66/33 or SATA 1.5G Audio 7.1 Channel High Definition Audio Codecs with UAA (Universal Audio Architecture) EAX™ 1.
Specifications Feature Specification PCMCIA One Type-II PCMCIA CardBus PC Card Slot Interface Four USB 2.0 Ports One Mini-IEEE 1394 Port One External Monitor Port One Parallel Port (LPT1) Supporting ECP/EPP One S/PDIF Output Jack One S-Video-Out Port One Infrared Transceiver Card Reader Embedded 3-in-1 Card Reader (MS/ SD/ MMC) Communication 56K Plug & Play Fax/Modem v.
Specifications Feature Power Specification Models A & B - AC Adapter: Full Range AC Adapter 90 W 100~240V, 47~63Hz Models C & D - AC Adapter: Full Range AC Adapter 65 W 100~240V, 47~63Hz 6 Cell Smart Lithium-Ion Battery Pack, 4.4AH 12 Cell Smart Lithium-Ion Battery Pack, 6.
