Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: Power Safety Warning Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. VI • Only use a power adapter approved for use with this computer.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface Contents Notice .................................................................................I FCC Statement .............................................................II Instructions for Care and Operation .......................... IV Power Safety .............................................................. VI Battery Precautions ...................................................VII Cleaning .................................................................. VIII Servicing ...............
Preface TouchPad and Buttons/Mouse .......................................2-8 Audio Features ...............................................................2-9 Audio Recording Setup .............................................2-10 Adding a Printer ...........................................................2-11 USB Printer ..............................................................2-11 Parallel Printer ..........................................................2-11 Power Management Overview .............
Preface PC Camera Module ....................................................4-8 Fingerprint Module .....................................................4-8 BIOS Utilities Overview ........................................................................5-1 The Power-On Self Test (POST) ...................................5-2 Failing the POST .........................................................5-3 Fatal Errors .................................................................5-3 Non-Fatal Errors ........
Preface Troubleshooting Overview ........................................................................8-1 Basic Hints and Tips ......................................................8-2 Backup and General Maintenance .................................8-3 Viruses ...........................................................................8-4 Upgrading and Adding New Hardware/Software ..........8-5 Problems and Possible Solutions ...................................8-7 Screen Resolution Error ................
Preface Optional ........................................................................ D-5 Windows XP Information DVD Regional Codes ................................................... E-2 Windows XP Start Menu & Control Panel ................... E-3 TouchPad and Buttons/Mouse ...................................... E-4 Function Keys/Hot Keys ............................................... E-5 PC Camera Hot Key Buttons ........................................ E-6 Application Quick Buttons ...............
Preface LAN ............................................................................ E-38 TouchPad .................................................................... E-38 CardReader ................................................................. E-38 Hot Key Utility (Model A & B Computers) ............... E-38 Hot Key Utility (Model C Computers) ....................... E-38 Quick Button Utility ................................................... E-39 802.11 b/g USB WLAN Module ......................
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 • Chapter 3 • Chapter 4 • Chapter 5 • Chapter 6 • Chapter 7 • Chapter 8 • Appendix A • • • • Appendix B Appendix C Appendix D Appendix E A guide to using some of the main features of the computer e.g.
1 Quick Start Guide Model Differences This notebook series includes three different model types. The models differ as indicated in the table below.
Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the remainder of the User’s Manual. You may also find the notes marked with a of interest to you.
1 Quick Start Guide Not Included Operating Systems (e.g. Windows Vista/Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1.
Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find this manual refers to the Microsoft Windows Vista operating system (see the table below). Further information on installing the drivers and utilities is available in Chapters 4 & 7 of the expanded User’s Manual on the Device Drivers & Utilities + User’s Manual CD-ROM.
1 Quick Start Guide System Startup 1. 2. 3. 4. 5. 6. 7. Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle, and press the power button to turn the computer “on”.
Quick Start Guide System Map: LCD Panel Open (Models A & B) 1. 2. 3. 4. 5. 6. Optional Built-In PC Camera LCD Speakers Power Button Hot Key Buttons Hot Key Buttons (Record Audio & PC Camera Zoom) 7. Keyboard 8. TouchPad and Buttons 9. Built-In Microphone 10. LED Indicators 11. Fingerprint Reader (Optional) 1 Wireless Device Operation Aboard Aircraft 2 The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
1 Quick Start Guide System Map: LCD Panel Open (Model C) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Optional Built-In PC Camera LCD Speakers Power Button Hot Key Buttons Keyboard TouchPad and Buttons Built-In Microphone LED Indicators Fingerprint Reader (Optional) 5 4 1 Wireless Device Operation Aboard Aircraft 2 3 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
Quick Start Guide LED Indicators The LED indicators display helpful information about the current status of the computer.
1 Quick Start Guide Keyboard Function Keys The keyboard has a numeric keypad for easy numeric data input, and features function keys to allow you to change operational features instantly. Note that Model C computers have a numeric keypad to the right of the main keyboard. Function Keys NumLk & ScrLk Keys Numeric Keypad The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down (see Table 1 - 4, on page 1 - 11).
Quick Start Guide Keys/ Button Function Keys/ Button Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F10 PC Camera Power Toggle Function Fn + F1 TouchPad Toggle Fn + F11 WLAN Module Power Toggle Fn + F2 Turn LCD Backlight Off (Press a key to or use TouchPad to turn on) Fn + F12 Bluetooth Module Power Toggle Fn + F3 Mute Toggle Fn + F4 Fn + F5/F6 Sleep Toggle Volume Decrease/ Increase Fn + F7 Fn + F8/F9 Display Toggle Brightness Decrease/ Increase Fn + NumLk Number Lock Toggle (Mode
1 Quick Start Guide Hot Key Buttons These buttons give instant access to the functions indicated in the table overleaf. The Application and zoom hot key functions depend on whether or not a PC Camera module is installed. Note that Model C does not have Audio Record and Zoom (or Application Quick Buttons 2 & 3) hot key buttons. In addition to the basic function key combinations visual indicators are available when the hot key driver is installed (see “Hot Key Utility” on page 4 - 6).
Quick Start Guide Hot Key Button Function PC Camera Installed Activate the Camera program/Take Still Picture (See Page 7 - 19) PC Camera Not Installed Activate Application Quick Button 1 (See Page 1 - 16) Activate the Default Internet Program Activate the Default E-Mail Browser Models A & B Only Models A & B Only Models A & B Only Audio Record Start/Stop (See Page 1 - 14) PC Camera Installed Camera Zoom-In (See Page 1 - 14) PC Camera Not Installed Activate Application Quick Button 2 (See Page 1 -
1 Quick Start Guide PC Camera Hot Key Buttons You can use the PC Camera hot key buttons to run the BisonCap or VideoView program, to take still pictures and to zoom the camera in and out (Models A & B only). 1. 2. 3. 4. 5. 6. Make sure the PC Camera is on (use the Fn + F10 key combination to power on the camera). Press the application hot key button once. The BisonCap/VideoView application will run. Use the zoom hot key buttons (Models A & B only) to obtain the picture required.
Quick Start Guide Recording Audio (Models A & B Only) The audio record hot key button allows you to record audio from either the builtin microphone, or from a microphone connected to the microphone-in jack. To record on the computer, setup the audio recording options in Windows as follows (also see Figure 2 - 8 on page 2 - 10). Model C Computers Note that Model C computers do not have audio record or camera zoom hot key buttons. 1. 2. 3. 4.
1 Quick Start Guide Application Quick Buttons Note that the quick button driver is designed to allow use of the Hot Key buttons as application quick buttons, if you have not included a PC Camera module in your purchase option (only install the quick button utility if the PC Camera is not installed). You will need to install the quick button utility to enable the functions. The application quick buttons give instant access to user-defined applications, with one quick button press.
Quick Start Guide System Map: Front & Rear Views 1. LED Indicators 2. 1 * USB Port 3. DC-In Jack 4. Battery 5.
1 Quick Start Guide System Map: Left View Figure 1 - 8 - Left View 1. 2. 3. 4. 5. 6. 7. Security Lock Slot Optical Device Drive Bay (see page 2 - 3) RJ-11 Modem Jack S/PDIF-Out Jack Microphone-In Jack 1 Headphone-Out Jack Recording Line-In Jack (see page A - 2) Models A & B 1 CD Emergency Eject If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole.
Quick Start Guide System Map: Right View Figure 1 - 9 - Right View Models A & B 1 2 3 3 1. 4 5 Model C 1 2 3 3 4 2. 3. 4. 5. ExpressCard Slot (see page 2 - 7) 7-in-1 Card Reader 2 * USB 2.0 Ports RJ-45 LAN Jack External Monitor Port 5 ExpressCard Slot The ExpressCard Slot accepts either ExpressCard/34 or ExpressCard/54 formats.
1 Quick Start Guide System Map: Bottom View Figure 1 - 10 - Bottom View 1. 2. 3. 4. Vent/Fan Intake/Outlet Battery Hard Disk Bay Cover CPU/RAM Bay Cover 2 CPU Models A & B 4 2 1 Model C 4 3 Overheating To prevent your computer from overheating make sure nothing blocks any Vent/Fan Intake while the computer is in use. 1 1 1 The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty.
Quick Start Guide Windows Vista Start Menu & Control Panel Most of the control panels, utilities and programs within Windows Vista (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
1 Quick Start Guide Video Features This computer features two different (either VIA for Model A or NVIDIA for Models B & C) video options. You will be provided with an appropriate driver on the Device Drivers & Utilities + User’s Manual CD-ROM. You can switch display devices, and configure display options, from the Display Settings control panel (in Personalization) in Windows Vista. To access Display Settings in Windows Vista: 1. 2. 3. 4. 5.
Quick Start Guide 4 1 2 3 1 2 5 3 Figure 1 - 12 - Display Settings Video Features 1 - 23 1
1 Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 21) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • • Hard Disk Drive Optical (CD/DVD) Device 7-in-1 Card Reader ExpressCard Slot TouchPad and Buttons/Mouse Audio Features Adding a Printer Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Figure 2 - 1 Hard Disk Location 2 - 2 Hard Disk Drive Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page D - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Security Menu” on page 5 - 9).
Features & Components 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Features & Components DVD Regional Codes 2 To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - 18. .
Features & Components 2 Card Reader Cover Make sure you keep the rubber cover provided in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. 7-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the Card Reader driver (see “CardReader” on page 4 - 6).
Features & Components ExpressCard Slot The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards). ExpressCard/54 is used for applications which require a larger interface slot, e.g. CompactFlash card reader. The number denotes the card width; 54mm for the Express Card/54 and 34mm for the ExpressCard/34.
Features & Components 2 Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details. TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.
Features & Components Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, or from the VIA Audio Deck icon in the taskbar, or on the desktop (this will bring up the VIA Audio Deck menu). The volume may also be adjusted by means of the Fn + F5/F6 key combination. Click any of the buttons (e.g. ) on the left to expand the audio menu selections.
Features & Components Audio Recording Setup 2 Audio recording options can be adjusted from the Sound control panel in Windows. 1. 2. 3. 4. 5. 6. 7. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Recording (tab). Right-click Microphone (VIA High Definition Audio) and make sure the item is not disabled (if you wish to record from the internal microphone make sure that the Front Mic is not disabled).
Features & Components Adding a Printer The most commonly used peripheral is a printer. The following conventions will help you to add a printer; however it is always best to refer to the printer manual for specific instructions and configuration options. USB Printer Most current printers have a USB interface connection. You may use any one of the ports to connect the printer. Install Instructions: 1. 2. 3. 4. 5.
Features & Components 2 2 - 12
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. 3 AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-in jack at the rear of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle.
Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Sleep/Hibernate hot key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will force the computer to shut down). Use Power Options (Hardware and Sound menu) control panel in Windows Vista to configure this feature.
Power Management 3 Resuming Operation See Table 3 - 1, on page 3 - 9 for information on how to resume from a power-saving state. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 1 Power Plan Advanced Settings 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance for maximum performance when the computer is powered from an AC power source.
Power Management 3 Power Button The Power Button in the Start Menu (in Classic View use the Shut Down button ) can be used to send the computer into a powersaving state. Sleep Mode & Mobile PC Battery A mobile PC in Sleep uses very little battery power. After an extended period of time the computer will save any open documents and applications to hard disk. Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management 3 Password Protection Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. It is recommended that you enable a password on wake up in order to protect your data. However you can disable this setting from the Power Options menu by clicking Require a password on wakeup in the left menu, and selecting the options (click Change settings that are currently unavailable).
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo). Power Status Icon To Resume Color Power Off Off Press the Power Button Sleep Blinking Green Press the Power Button Closing the Lid If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up.
Power Management 3 Low Battery Warning When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted. Battery Information Please follow these simple guidelines to get the best use out of your battery. Battery Charging on Model B & C Computers Note that Model B & C computers under a heavy load (e.g.
Power Management Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Advanced Settings (see Figure 3 - 1 on page 3 - 4). Click the battery icon status.
Power Management 3 Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display.
Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. 3 We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason see “Removing the Battery” on page 6 - 3. New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page 3 - 15 for instructions on how to do this).
Power Management Proper handling of the Battery Pack 3 Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 1. 2. 3. 3 Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options.
Power Management How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. 3 How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Power Management 3 3 - 18
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation Insert the Device Drivers & Utilities + User’s Manual CD-ROM and click Install Drivers (button) or Option Drivers (button). 1. 2. 4 3. Figure 4 - 1 - Drivers Installer Screen 1 Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below.
Drivers & Utilities Driver Installation Order . Driver Page # Video (VIA - Model A) Page 4 - 5 Video (NVIDIA - Models B & C) Page 4 - 5 Audio Page 4 - 5 Modem Page 4 - 5 LAN Page 4 - 5 CardReader Page 4 - 6 TouchPad Page 4 - 6 Hot Key Utility Page 4 - 7 Quick Button Utility Page 4 - 7 802.
Drivers & Utilities 4 Updating/Reinstalling Individual Drivers User Account Control (Win Vista) If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Programs > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer).
Drivers & Utilities Driver Installation Procedure Insert the Device Drivers & Utilities + User’s Manual CD-ROM and click Install Drivers (button). Video (VIA - Model A) 1. Click 1.Install Video Driver > Yes. 2. Click Next > Next. 3. Click Finish to restart the computer. Video (NVIDIA - Models B & C) 1. Click 1.Install Video Driver > Yes. 2. Click Next. 3. Click Finish to restart the computer. Audio 1. Click 2.Install Audio Driver > Yes. 2. Click Next. 3.
Drivers & Utilities CardReader 1. Click 5.Install Cardreader Driver > Yes. 2. Click Next > Next. 3. Click Finish to restart the computer. 4 TouchPad 1. Click 6.Install Touchpad Driver > Yes. 2. Click Next. 3. Click Finish > Restart Now to restart the computer. Hot Key Utility 1. Click 7.Install Hotkey Driver > Yes. 2. Click Next > Install. 3. Click Finish > Finish to restart the computer.
Drivers & Utilities Quick Button Utility If you do not have a PC Camera module installed, you can install the Quick Button driver to enable you to use the hot key buttons to launch applications of your choice (see “Application Quick Buttons” on page 1 - 16 for details). Adding/Removing a PC Camera Note that the Quick Button and PC Camera drivers cannot co-exist. You will need to install the Quick Button driver manually as it does not appear in the Drivers Installer menu.
Drivers & Utilities Wireless LAN Module See the introduction in “802.11 b/g USB WLAN Module” on page 7 - 2, and check the installation procedure. 4 Bluetooth Module Note: The operating system is the default setting for Bluetooth control in Windows Vista, and does not require a driver. See “Bluetooth Module” on page 7 - 7 for configuration instructions. PC Camera Module See the introduction in “PC Camera Module” on page 7 - 11, and check the installation procedure.
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your system ever needs servicing.
BIOS Utilities POST Screen 5 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST Note: The POST screen as pictured right is for guideline purposes only. The POST screen on your computer may appear slightly different. If you disable the Boottime Diagnostic Screen, the POST screen will not appear.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus 5 The Setup menus shown in this section are for reference only. Your computer’s menus will indicate the configuration appropriate for your model and options. Along the top of the screen is a menu bar with five (5) menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup.
BIOS Utilities Main Menu PhoenixBIOS Setup Utility Main Main Advanced Security Boot Figure 5 - 2 Exit Main Menu Item Specific Help 09 [22:11:05] [08/20/2007] System Time: System Date: IDE Channel 0 Master IDE Channel 2 Master System Memory Extended Memory F1 Esc Help Exit [Optiarc DVD-RW AD-7530B-(] [FUJITSU MHV2100BH PL-(S1)] , , or selects field.
BIOS Utilities IDE Channel 0/2 Master (Main Menu) Pressing Enter opens the sub-menu to show the configuration of either a DVD/CD Device or HDD on the computer’s IDE Channels. Use the Auto (Type:) setting to have the items configured automatically for you. System/Extended Memory: (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed.
BIOS Utilities Advanced Menu Figure 5 - 3 PhoenixBIOS Setup Utility Main Advanced Advanced Security Boot Exit Advanced Menu Item Specific Help Installed O/S: Boot-time Diagnostic Screen: Legacy USB Support: Reset Configuration Data: [WinXP/Vista] [Enabled] [Enabled] [No] Select the operating system installed on your system which you will use most commonly. 5 Note: An incorrect setting can cause some operating systems to display unexpected behavior.
BIOS Utilities Boot-time Diagnostic Screen: (Advanced Menu) Use this menu item to enable/disable the Boot-time Diagnostic Screen (see “The Power-On Self Test (POST)” on page 5 - 2). Legacy USB Support: (Advanced Menu) Choose “Enabled” if you intend to use USB devices in systems which do not normally support USB functionality (e.g. DOS). The default setting is “Enabled” and does not need to be changed if you intend to use your USB devices in Windows.
BIOS Utilities Security Menu Main Advanced Figure 5 - 4 PhoenixBIOS Setup Utility Security Security Boot Exit Security Menu Item Specific Help Supervisor Password Is: Clear Set Supervisor Password [Enter] Password on boot: Fixed disk boot sector: [Disabled] [Normal] Supervisor Password controls access to the setup utility.
BIOS Utilities Password Warning 5 If you set a boot password (Password on boot is “Enabled“), NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. 5 - 10 Security Menu Password on boot: (Security Menu) Specify whether or not a password should be entered to boot the computer.
BIOS Utilities Boot Menu PhoenixBIOS Setup Utility Main Advanced Security Boot Figure 5 - 5 Exit Item Specific Help Boot priority order: 1: IDE 0: Optiarc DVD RW AD 7530B-(P 2: IDE 4: FUJITSU MHV2100BH PL-(S1) 3: USB HDD: 4: USB KEY: 5: USB FDC: 6: PCI BEV: 7: 8: Excluded from boot order: : USB CDROM: : USB ZIP : USB LS120 : PCI SCSI F1 Esc Help Exit Select Item Select Menu -/+ Enter Boot Menu Keys used to view or configure devices: Up and Down arrows select a device.
BIOS Utilities Exit Menu Figure 5 - 6 Exit Menu PhoenixBIOS Setup Utility Main Advanced Security Boot Exit Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes 5 F1 Esc Help Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. 4. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Slide the battery out in the direction of the arrow 3 .
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CD-ROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer 4. Grip the tab and slide the hard disk in the direction of arrow 6 Models A & B . Model C Figure 6 - 3 HDD Slide 6 5. 6. 7. 6 Lift the hard disk up in the direction of arrow 7 . Remove the screws 8 & 9 and cover 10 . Reverse the process to install a new hard disk drive.
Upgrading The Computer Upgrading the Optical (CD/DVD) Device 1. 2. 3. 4. 5. Turn off the computer, and turn it over and remove the battery. Remove the HDD bay cover screws 1 - 3 (Models A & B)/ 1 - 4 (Model C). Remove the HDD bay cover 5 . Remove the screw at point 6 , and use a screwdriver to carefully push out the optical device at point 7 . Reverse the process to install the new device.
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 200 pin Small Outline Dual In-line (SODIMM) DDRII (DDR2) type memory modules (see “Memory” on page D - 2 for details of supported module types). The total memory size is automatically detected by the POST routine once you turn on your computer. 1. 2. Turn off the computer, and turn it over and remove the battery. Locate the CPU/RAM bay cover and remove screws 1 - 7 .
Upgrading The Computer 3. Remove the bay cover 8 . Figure 6 - 7 CPU/RAM Bay Cover Removed Models A&B 8 6 Model C 8 Contact Warning Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. 4. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 9 & 10 ) in Figure 6 - 8.
Upgrading The Computer 5. The RAM module will 11 pop-up, and you can remove it. Figure 6 - 9 RAM Module Removal 11 6 6. 7. Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. 8. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit without much pressure. 9.
Upgrading The Computer Warranty The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty. 6 Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard.
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. • • • • 802.11 b/g USB WLAN Module Bluetooth Module PC Camera Module Fingerprint Reader Module Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + F11 key combination to toggle power to the WLAN module, and check the indicator to see if the module is powered on or not (see Table 1 - 4, on page 1 - 11/Table 1 - 3, on page 1 - 9). 802.11 b/g USB WLAN Module If you have included an 802.
Modules & Options Connecting to a Wireless Network Make sure the Wireless LAN module is turned on. 1. Click the taskbar wireless icon , and then click Connect to a network (or rightclick the icon , and then click Connect to a network). Figure 7 - 1 Taskbar Menus Click icon Right-click icon 2. 3. In the Show list, click to choose Wireless from the drop-down menu. A list of currently available networks will appear.
Modules & Options 4. 5. Click a network, and then click Connect. If you do not see a network you want to connect to, click Set up a connection or network (a list of options will appear allowing manual searching, and creating a new network). 6. Move the cursor over the taskbar icon Figure 7 - 3 Connecting 7 Figure 7 - 4 Connection Status 7 - 4 802.11 b/g USB WLAN Module to see the connection status (see below).
Modules & Options 7. To disconnect from the wireless network you can click the taskbar wireless icon , and then select Connect or disconnect to access the network menu, and click Disconnect (or right-click the icon , and then click Disconnect from). Click icon Security Enabled Networks You should try to make sure that any network you are connecting to is a secure network. Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Modules & Options Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center: 1. 2. 3. 7 Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Windows Mobility Center (Mobile PC). Click the button to Turn wireless off/on, or click the icon to access the network menu.
Modules & Options Bluetooth Module The operating system’s Bluetooth Devices control panel is used to configure the Bluetooth settings in Windows Vista, and therefore does not require a driver. Use the Fn + F12 key combination (see Table 1 - 4, on page 1 - 11) to toggle power to the Bluetooth module.
Modules & Options Bluetooth Configuration in Windows Vista Bluetooth Taskbar Icon 7 If you cannot see the Bluetooth icon in the taskbar, access the Bluetooth Devices control panel. Click Options (tab), and make sure that Show Bluetooth icon in the notification area check box has a tick inside it. Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation).
Modules & Options To Add a Bluetooth Device 1. 2. 3. 4. 5. Access the Bluetooth Devices control panel. Click Options (tab), and make sure that Allow Bluetooth devices to connect to this computer check box (Connections) has a tick inside it. Click Devices (tab), and then click Add. The Add Bluetooth Device Wizard will appear. Click to select “My device is set up and ready to be found”, and then click Next. Figure 7 - 8 Add Bluetooth Device Wizard Passkey Options 6. 7. 8.
Modules & Options To Change Settings for the Bluetooth Device 1. 2. Bluetooth Help 7 To get help on Bluetooth configuration and settings, select Help and Support from the Start menu. Type Bluetooth in the Search Help box, and select an item from the returned search results to get more information. Access the Bluetooth Devices control panel. Click on the device you want to change and click Properties to: • • Change the name of the device (click General, type a new name and click OK).
Modules & Options PC Camera Module There are 2 camera options available for this computer, depending on your purchase configuration. The 1.3M pixel camera module uses the BisonCap application to capture video files, and the 2.0M pixel camera module uses the VideoView application to capture video files. Before installing the PC Camera driver, make sure that the optional PC Camera is on. Use the Fn + F10 key combination (see Table 1 - 4, on page 1 - 11) to toggle power to the PC Camera module.
Modules & Options Resuming from Power Saving & PC Camera 7 After the system resumes from Sleep or Hibernate, you will need to use the Fn + F10 key combination to power on the PC Camera before running the PC Camera application. PC Camera Driver Installation 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual CD-ROM into the CD/DVD drive. 2. Click Option Drivers (button), and then click 2.Install Camera Driver > Yes. For the 1.3M Pixel Camera Module: 1.
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Recording (tab). Right-click Microphone (VIA High Definition Audio) and make sure the item is not disabled (if you wish to record from the internal microphone make sure that the Front Mic is not disabled). 5.
Modules & Options Figure 7 - 11 Audio Setup for PC Camera Right-click 7 7 - 14 PC Camera Module
Modules & Options BisonCap (1.3M Cam)/VideoView (2.0M Cam) BisonCap and VideoView are video viewers for general purpose video viewing and testing, and capturing video files to .avi format. 1. 2. 3. 4. Setup your Windows Color and Appearance to Windows Aero before running the BisonCap/VideoView application (see “Color Scheme Setup” on page 7 - 11). Run the BisonCap/VideoView program from the Start > Programs/All Programs > BisonCam/USB2.
Modules & Options Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties) If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Modules & Options Eliminating Screen Flicker If you find that the video screen in the BisonCap/VideoView program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. Run the BisonCap/VideoView program. Go to Options and scroll down to select Video Capture Filter.... For Bison Cap: 3. Click either 50Hz or 60Hz under Frequency in Property Page (tab). For VideoView: 4. Click either 50Hz or 60Hz under Flickering Reduction in Image (tab).
Modules & Options Zoom The BisonCap and VideoView programs allow you to zoom the camera in and out. 1. Run the BisonCap/Video View program. For Bison Cap: 2. Figure 7 - 13 Zoom/Setting Go to Zoom and select Zoom Out/Zoom In. For Video View: 3. Go to Options and scroll down to select Setting (Use the slider to adjust the zoom level, and click OK to save the setting). Bison Cap 7 VideoView Snapshot Folder The Snapshot folder’s default location is on the desktop.
Modules & Options Fingerprint Reader Module If you have included the fingerprint reader in your purchase option you will need to install the driver as per the instructions below. Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full security protection. Before beginning the enrollment process it is recommended that you go through the fingerprint tutorial.
Modules & Options User Enrollment 1. 2. 3. 7 Click Start > Programs/All Programs > Protector Suite QL > User Enrollment, or double click the taskbar icon . On the first run of the program you will be asked to click the button to accept the license, and then click OK. Click Next and select “Enrollment to the hard disk”, and click Finish. Figure 7 - 14 Enroll to Hard Disk 4. 5. 6. 7. 8.
Modules & Options 9. 10. 11. 12. 13. 14. Click the button above any of the fingers to begin the enrollment process for that finger. Swipe the finger three times to enroll that finger. Repeat the process for all the fingers you wish to enroll (see sidebar), and then click Next. Click Finish. Click any of the headings under “Learn more about:” to get more information on any topic. Click Close.
Modules & Options Help & Manual 16. Right-click the taskbar icon to bring up the menu that allows you to Edit Fingerprints, Start Control Center, access the Help menu etc. You can also run the Control Center etc. from the Protector Suite QL item in the Programs/All Programs menu. Right-click the taskbar icon to bring up the menu to select Help. Help may also be accessed from the Fingerprint Control Center. 7 Figure 7 - 16 Control Center & Biomenu 17.
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “LED Indicators” on page 1 - 9) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED power indicator , is blinking orange. Low Battery. Plug in the DC power source.
Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 20). Make sure you’re using the correct adapter.
Troubleshooting Problem You forget password. the Possible Cause - Solution boot If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Problem Possible Cause - Solution The CD/DVD tray will not open when there is a disc in the tray. The CD/DVD is not correctly placed in the tray. Gently try to remove the disc using the eject hole (see “Loading Discs” on page 2 - 3). The DVD regional codes can no longer be changed. The code has been changed the maximum 5 times. See “DVD Regional Codes” on page 2 - 5/ “DVD Regional Codes” on page E - 2. Unwelcome numbers appear when typing.
Troubleshooting Problem Possible Cause - Solution The Wireless LAN/ Bluetooth modules cannot be detected. The modules are off. Check the LED indicator and/or function key indicator to see if the WLAN/Bluetooth module is on or off (see “LED Indicators” on page 1 - 9). If the LED indicator is off, then press the Fn + F11 (WLAN) or Fn + F12 (Bluetooth) key combination(s) in order to enable the modules (see “Function Keys” on page 1 - 10). The PC Camera module cannot be detected. The module is off.
Troubleshooting Problem Possible Cause - Solution The audio at Windows startup, or when playing mp3 format files in Windows Media Player, appears to lag. This is a known issue with Celeron M CPUs. Contact your service center for CPU upgrade information. The Bluetooth module is off after resuming from Sleep. The Bluetooth module’s default state will be off after resuming from the Sleep power-saving state.
Troubleshooting Screen Resolution Error If you are experiencing either screen resolution reduction, or screen flickering after resuming from Sleep in Windows Vista then follow the instructions below to fix this problem. This error arises in compliance with Windows Vista policy, which triggers TMM (Transient Multi-Manger) when the notebook lid (S3) is closed. TMM disconnects the LCD display from the OS and then adds the LCD display back when the lid is opened.
Troubleshooting 3. 4. 5. Double-click Task Scheduler Library > Microsoft > Windows. Click MobilePC to open the control panel. Right-click TMM and select Disable. 8 Figure 8 - 2 - TMM Disable 6. Close all the control panels.
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer. External Monitor (VGA) Port This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD.
Interface (Ports & Jacks) Item Description RJ-11 Modem Jack This port connects to the built-in modem. You may plug the telephone line directly into this RJ-11 telephone connection. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port. RJ-45 LAN Jack This port supports LAN (Network) functions. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port. Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot.
Interface (Ports & Jacks) A A - 4
VIA Video Driver Controls Appendix B: VIA Video Driver Controls (Model A Computers) The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 16. VIA Video Driver Installation Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 6. Insert the Device Drivers & Utilities + User’s Manual CD-ROM and click Install Vista Drivers (button). Video 1. Click 1.Install Video Driver > Yes. 2. Click Next > Next. 3. Click Finish to restart the computer.
VIA Video Driver Controls Function Key Combination You can use the Fn + F7 key combination to toggle through the display options: • Notebook Only • External Display Only • Notebook + External Display Make sure you give the displays enough time to refresh. Advanced Video Controls This section is about making adjustments for the LCD, and switching display devices. The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 22.
VIA Video Driver Controls VIA S3Tray Plus Utility The S3Tray Plus utility will appear in the taskbar when the video driver is installed. Click/Right-click the icon to bring up the menu below. From this menu you will also be able to make display adjustments, access the Display Properties control panel, check video memory information etc. Click Icon Taskbar Icon If you cannot see the tray icon you can enable it from the S3 control panel.
VIA Video Driver Controls Attaching Other Displays Besides the built-in LCD, you can also use an external monitor (CRT)/flat panel display as your display device. Connect it to the external monitor port on the right of the computer, and follow the instructions below: Windows Vista 1. 2. 3. Attach your external display to the external monitor port and turn it on.
VIA Video Driver Controls External displays may also be configured from S3Display tab in Advanced Display Settings: 1. 2. 3. 4. 5. 6. 7. Attach the external display to the external monitor port and turn it on. Click Advanced Settings in the Display Settings control panel (see “Video Features” on page 1 - 22) to display the additional tabs. Select S3Display (tab). Click to put a tick in the tickbox under the CRT icon. Click Apply > OK and allow the monitor time to refresh the display.
VIA Video Driver Controls Display Modes Single Display Only one of your attached displays is used. Mirrored This display mode simply shows an exact copy of the Primary display desktop on the Secondary display(s). Extended Desktop An Extended desktop allows the desktop to span the displays to act as a large work area, thus creating a lot more screen area for display. Each display device can be configured independently for specific resolutions and refresh rates.
VIA Video Driver Controls Using Windows Vista to Enable Extended Mode 1. 2. 3. 4. 5. Attach your external display to the external monitor port, and turn it on. If a New Display Detected window does not appear in Windows Vista, go to the Windows Mobility Center control panel (Mobile PC > Adjust commonly used mobility settings) and click Connect display. Click to select Show different parts of my desktop on each display (extended). Click Right or Left under Extend your desktop. Click Apply > OK.
VIA Video Driver Controls Using Display Settings to Enable Extended Mode 1. 2. 3. Attach your external display to the external monitor port, and turn it on. Open the Display Settings control panel (see “Video Features” on page 1 - 22). Click the monitor icon (e.g. 2 ), and make sure you have checked “Extend my Windows desktop onto this monitor.” and click Apply. Click the appropriate monitor icon (e.g. 2 ) to be able to select the option to extend the desktop on to it.
NVIDIA Video Driver Controls Appendix C: NVIDIA Video Driver Controls (Model B & C Computers) The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 22. Resolution Error NVIDIA Video Driver Installation Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Insert the Device Drivers & Utilities + User’s Manual CD-ROM and click Install Drivers (button). 1. Click 1.Install Video Driver > Yes. 2. Click Next. 3.
NVIDIA Video Driver Controls NVIDIA Control Panel To access the GeForce..... control panel from the desktop; right-click the desktop, then click NVIDIA Control Panel. C NVIDIA Control Panel More advanced video configuration options are provided in the NVIDIA Control Panel tab. 1. 2. 3. 4. Open the Display Settings (see page 1 - 22) control panel. Click Advanced Settings (button). Click GeForce..... (tab). Click Start the NVIDIA Control Panel to make any video adjustments 1. 2.
NVIDIA Video Driver Controls The NVIDIA Control Panel provides additional video configuration controls and tools which allow quick access to features such as display configuration, 3D Settings and Help menus etc. Navigating the Control Panel Navigate through the control panels in much the same way as you would a web page. Click on the sub-heading tasks in the left menu (and on the highlighted links) for information. Use the buttons on the top left to go back, forward etc.
NVIDIA Video Driver Controls The Help menus provide index and search features, and direct links to the NVIDIA website etc.
NVIDIA Video Driver Controls Attaching Other Displays Configuring an External Display in Windows Vista 1. 2. 3. Attach your external display to the external monitor port and turn it on. If a New Display Detected window does not appear in Windows Vista, go to the Windows Mobility Center control panel (Mobile PC > Adjust commonly used mobility settings) and click Connect display.
NVIDIA Video Driver Controls Function Key Combination You can use the Fn + F7 key combination to toggle through some display options: Configuring an External Display using the NVIDIA Control Panel Alternatively you can use the NVIDIA control panel to configure any attached displays. 1. 2. 3. Attach your external display to the external monitor port/DVI-Out Port (or TV to the S-Video-Out jack), and turn it on. Go to NVIDIA Control Panel (see “NVIDIA Control Panel” on page C - 2).
NVIDIA Video Driver Controls Display Modes Single Display Mode Only one of your displays is used. Clone Mode Clone Mode simply shows an exact copy of the Primary display desktop on the other display(s). This mode will drive multiple displays with the same content. Dualview Mode Dualview Mode treats both connected displays as separate devices, and they act as a virtual desktop resulting in a large workspace. When Dualview is enabled, you can drag any icons or windows across to the other display desktop.
NVIDIA Video Driver Controls Using New Display Detected to Enable Extended Mode 1. 2. 3. 4. 5. Figure C - 6 New Display Detected (Extended) C C - 8 Display Modes Attach your external display to the external monitor port and turn it on. If a New Display Detected window does not appear in Windows Vista, go to the Windows Mobility Center control panel (Mobile PC > Adjust commonly used mobility settings) and click Connect display.
NVIDIA Video Driver Controls Using Display Settings to Enable Extended Mode 1. 2. 3. 4. Attach your external display to the external monitor port and turn it on. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Adjust screen resolution under the Appearance and Personalization menu (or double-click Personalization > Display Settings). Click the monitor icon (e.g. 2 ), and make sure you have checked “Extend the desktop onto this monitor.” and click Apply.
NVIDIA Video Driver Controls C C - 10
Specifications Appendix D: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, delayed or updated due to the manufacturer's release schedule. Check with your service center for details.
Specifications Feature Memory Specification Two 200 Pin SO-DIMM Sockets Supporting DDRII (DDR2) 533/667 MHz 64-bit Wide DDRII (DDR2) Data Per Channel Memory Expandable up to 2GB (256/ 512/ 1024 MB DDRII Modules) LCD Models A & B Model C 15.4" WXGA (1280 * 800) TFT LCD OR 15.4‘” WXGA+ (1440 * 900) TFT LCD 17.0" WXGA (1440 * 900) TFT LCD OR 17.1" WSXGA+ (1680 * 1050) TFT LCD OR 17.
Specifications Feature Specification Storage One Changeable 12.7mm(h) Optical Device (CD/DVD) Type Drive (see “Optional” on page D - 5 for drive options) Easy Changeable 2.5" 9.5 mm (h) SATA (Serial) HDD Audio Integrated AZALIA Compliant Interface (HDA) 3D Stereo Enhanced Sound System Sound-Blaster PRO™ Compatible 2 * Built-In Speakers Built-In Microphone Keyboard & Pointing Device Winkey Keyboard Built-In TouchPad with Scrolling Function Interface Three USB 2.
Specifications Feature Specification Communication AZALIA 56K Plug & Play Fax/Modem V.90/92 Compliant 10M/100Mb Base-TX Ethernet LAN 802.11 b/g USB Wireless LAN Module (Option) Bluetooth 2.0 + EDR (Enhanced Data Rate) Module (Factory Option) 1.3M or 2.0M Pixel USB PC Camera Module (Factory Option) Power Management Supports ACPI 2.0 and PCI Bus Power Management 1.1 Compliant Power Models A & B Full Range AC/DC Adapter AC input 100 - 240V, 50 - 60Hz, DC Output 19V, 3.42A (65 Watts) OR 18.5V, 3.
Specifications Feature Optional Specification Optical Drive Module Options: DVD/CD-RW Combo Drive Module DVD-Dual Drive Module (Super Multi) Fingerprint Reader Module (Factory Option for Models B & C Only) 802.11 b/g USB Wireless LAN Module 1.3M or 2.0M Pixel USB PC Camera Module (Factory Option) Bluetooth 2.
Specifications D D - 6
Windows XP Information Appendix E: Windows XP Information This Appendix contains information (including control panel information, driver installation etc.) for users of the Windows XP OS. Model C Computers Note that Model C computers do not have audio record or camera zoom hot key buttons.
Windows XP Information DVD Regional Codes Changing DVD Regional Codes Go to the Control Panel and double-click System > Hardware (tab), click Device Manager, then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialogue box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code. DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times.
Windows XP Information Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can customize the look of the Start menu by right-clicking the Start menu and selecting Properties from the menu.
Windows XP Information TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. Once you have installed the TouchPad driver (see “TouchPad” on page E - 38) you can configure the functions by double-clicking the TouchPad driver icon on the taskbar.
Windows XP Information Function Keys/Hot Keys The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. Table 1 - 4, on page 1 - 11 gives details of function key combinations, hot key buttons and visual indicators. In addition to the basic function key combinations visual indicators are available when the hot key driver is installed (see “Hot Key Utility (Model A & B Computers)” on page E - 38/“Hot Key Utility (Model C Computers)” on page E - 38).
Windows XP Information PC Camera Hot Key Buttons Snapshot Folder The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture using the application hot key button. If you accidentally delete or move the folder, you can create a new Snapshot folder on the desktop in order to capture the files.
Windows XP Information Application Quick Buttons Note that the application quick button utility is designed to allow use of the hot key buttons in absence of the optional PC Camera. You will need to install the Quick Button Utility (see “Quick Button Utility” on page E - 39) to enable the functions. The quick buttons give instant access to user-defined applications, with one quick button press. To configure a program to open when the buttons are pressed, follow the instructions below.
Windows XP Information Recording Audio (Model A & B Computers) The audio record hot key button allows you to record audio from either the built-in microphone, or from a microphone connected to the microphone-in jack. To record on the computer, setup the audio recording options in Windows as follows (see Figure E - 6 on page E - 9). 1.
Windows XP Information Figure E - 6 Audio Setup for Recording (Windows XP) E Recording Audio E - 9
Windows XP Information Sound Volume Adjustment How high the sound volume can be set depends on the setting of the volume control within Windows (and the volume control function keys on the computer). Click the Volume icon on the taskbar to check the setting. Audio Features You can configure the audio options on your computer from the Sounds and Audio Devices Windows control panel, or from the VIA Audio Deck icon in the taskbar, or on the desktop (this will bring up the VIA Audio Deck menu).
Windows XP Information Video Features This computer features two different video (either VIA for Model A or NVIDIA for Model B & C Computers) options (see “Video Adapter” on page D - 2 for details). You will be provided with an appropriate driver on the Device Drivers & Utilities + User’s Manual CD-ROM (WinXP). You can switch display devices, and configure display options, from the Display Properties control panel in Windows as long as the video driver is installed.
Windows XP Information Function Key Combination You can use the Fn + F7 key combination to toggle through the display options: • Notebook Only • External Display Only • Notebook + External Display Make sure you give the displays enough time to refresh. Advanced Video Controls This section is about making adjustments for the LCD, and switching display devices.
Windows XP Information VIA Video Driver Controls (Model A Computers) VIA S3Tray Plus Utility The S3Tray Plus utility will appear in the taskbar when the video driver is installed. Click/Right-click the icon to bring up the menu below. From this menu you will also be able to make display adjustments, access the Display Properties control panel, check video memory information etc.
Windows XP Information Help Menus Right-click on almost any item in the tabs to bring up the “What’s This?” button. VIA S3 Display Control Panels Right-click the S3Tray Plus utility in the taskbar to bring up the menu for the individual control panels, or access the menus from the Advanced tab in the Display Properties control panel. Click the “What’s This?” button to bring up a help menu (if the item has a help menu associated with it).
Windows XP Information Display Devices (VIA) Besides the built-in LCD, you can also use an external monitor (CRT)/flat panel display as your display device. Connect it to the external monitor port on the right of the computer. See the instructions below: S3Tray Plus Utility You can also use the S3Tray Plus utility in the taskbar to configure an external display. Attach the external display (CRT) to the external monitor port. Right-click the icon in the taskbar and select S3Display. 1. 2. 3. 4. 5. 6.
Windows XP Information Playing DVD Videos If you want to play a DVD video in a multiple monitor mode, then choose EITHER the notebook LCD OR external display as the display device. It is not possible to play a DVD video simultaneously on both displays. Display Modes (VIA) Single Display Only one of your attached displays is used. Multiple Monitors This display mode simply shows an exact copy of the Primary display desktop on the Secondary display(s).
Windows XP Information To Enable Extended Desktop (Display Properties) 1. 2. 3. 4. 5. Attach the external display to the external monitor port and turn it on. Go to the Display Properties control panel (see “Video Features” on page E - 11) and click Settings (tab). Click the monitor icon (e.g. 2 ), and click to put a tick in the “Extend my Windows desktop onto this monitor.” box, and then click Apply.
Windows XP Information GeForce Control Panel To access the GeForce..... control panel from the desktop: Right-click the desktop, then point to or click NVIDIA Control Panel. NVIDIA Video Driver Controls (Model B & C Computers) More advanced video configuration options are provided in the GeForce..... control panel tab. 1. 2. 3. 4. Open the Display Properties (see “Video Features” on page E - 11) control panel. Click Advanced (button). Click GeForce..... (tab).
Windows XP Information Control Panels (NVIDIA) Select a task from the menu on the left to display the appropriate control panel. The NVIDIA Control Panel provides additional video configuration controls and tools which allow quick access to features such as 3D Settings, Display and Mobile configuration etc. Navigating the Control Panel Navigate through the control panels in much the same way as you would a web page. Click on the headings, menus and highlighted links for information.
Windows XP Information Display Devices and Modes (NVIDIA) Besides the built-in LCD, you can also use an external monitor/flat panel display as your display device. The following are the display options: 1. 2. 3. The built-in LCD. An external monitor connected to the external monitor port. A flat panel display connected to the external monitor port. Configure the display modes for any attached display devices from the NVIDIA Control Panel (Set Up Multiple Displays - see page E - 21).
Windows XP Information Attaching Other Displays (NVIDIA) 1. 2. 3. Attach your external display to the external monitor port and turn it on (see sidebar). Go to the NVIDIA Control Panel. Click Display, and then click Set Up Multiple Displays. Function Key Combination You can use the Fn + F7 key combination to toggle through some display options: • Notebook Only • External Display Only • Notebook + External Display Make sure you give the displays enough time to refresh.
Windows XP Information OS Note Power management functions will vary slightly depending on your operating system. For more information it is best to refer to the user’s manual of your operating system. (Note: All pictures used on the following pages are from the Windows XP OS.) Power Management Features To conserve power, especially when using the battery, your computer uses the ACPI power management system.
Windows XP Information The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-in jack at the rear of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle.
Windows XP Information Shutdown Note that you should always shut your computer down by choosing the Turn Off Computer command from the Start menu in Windows. This will help prevent hard disk or system problems. Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.
Windows XP Information Power Schemes You can set your computer to conserve power through individual components by means of Power Schemes. You can also adjust the settings for each scheme to set the monitor to turn off after a specified time, and the computer's hard disk motor to turn off if the hard disk drive has not been accessed for a specified period of time (if the system reads or writes data, the hard disk motor will be turned back on).
Windows XP Information Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source.
Windows XP Information System Power Options You can use the system power options to stop the computer’s operation and restart where you left off. This system features Stand by and Hibernate sleep mode levels (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - see “Hibernate” on page E - 28). Hibernate Mode vs. Shutdown Hibernate mode and Shutdown are the same in that the system is off and you need to press the power button to turn it on.
Windows XP Information Stand by System Resume The system can resume from Stand by mode by: • Pressing the power button • Pressing the Sleep/ Resume key combination • An incoming call received on the modem (if enabled) Stand by saves the least amount of power, but takes the shortest time to return to full operation. During Stand by the hard disk is turned off, and the CPU is made to idle at its slowest speed. All open applications are retained in memory.
Windows XP Information Configuring the Power Button The power button may be set to send the computer in to either Stand by or Hibernate mode. In Stand by mode, the LED will blink green. In Hibernate mode the LED will be off (battery) or orange (AC/DC adapter). If you are in a power saving mode set to save power through individual components (e.g. hard disk, monitor), the LED will remain green. Sleep Button You may also configure the Sleep/Resume key combination (Fn + F4) from the menu illustrated.
Windows XP Information Low Battery Warning When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted. Battery Information Please follow these simple guidelines to get the best use out of your battery. New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page E - 33 for instructions on how to do this).
Windows XP Information Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you need to remove the battery for any reason, see “Removing the Battery” on page 6 - 3.
Windows XP Information Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center.
Windows XP Information Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer by yourself even when you see a message that indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
Windows XP Information Driver Installation Insert the Device Drivers & Utilities + User’s Manual CD-ROM and click Install Drivers (button) or Option Drivers (button). 1. 2. 3. Figure E - 20 - Drivers Installer Screen 1 E Check the driver installation order from Table E - 2, on page E - 35 (all the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below.
Windows XP Information Driver Installation Order WinXP (SP2) Driver Page # Note Chipset Page E - 37 VIA (Model A) Page E - 37 NVIDIA (Models B & C) Page E - 37 Bus Page E - 37 Manual Driver Installation Click Browse CD (button) in the Drivers Installer application and browse to the executable file in the appropriate driver folder.
Windows XP Information If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and doubleclick the Add/Remove Programs item. If you see the individual driver listed (if not see below), uninstall it, following the on screen prompts (it may be necessary to restart the computer). Go to the appropriate section of the manual to complete the update/reinstall procedure for the driver in question.
Windows XP Information New Hardware Found If you see the message “New Hardware Found” (Found New Hardware Wizard) during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure as directed. Service Pack Information Make sure you install Windows XP Service Pack 2 (or a Windows XP version which includes Service Pack 2) before installing any drivers. Chipset 1. Click 1.Install Chipset Driver > Yes. 2.
Windows XP Information Modem 1. Click 4.Install Modem Driver > Yes. 2. Click OK. 3. The modem is ready for dial-up configuration. 4. Check if the modem country selection is appropriate for you (Control Panel > Phone and Modem Options). Audio 1. Click 5.Install Audio Driver > Yes. 2. Click Next > Next > Next. 3. Click Finish to restart the computer. LAN 1. Click 6.Install LAN Driver > Yes. 2. Click OK. 3. The network settings can now be configured. TouchPad 1. Click 7.Install Touchpad Driver > Yes. 2.
Windows XP Information Quick Button Utility Module Drivers If you do not have a PC Camera module installed, you can install the Quick Button driver to enable you to use the hot key buttons to launch applications of your choice (see “Application Quick Buttons” on page E - 7 for details). See the following pages for the driver installation procedures for any of the optional modules included in your purchase configuration. Wireless LAN Module See “802.11 b/g USB WLAN Module” on page E - 40.
Windows XP Information Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Use the Fn + F11 key combination to toggle power to the WLAN module, and check the indicator to see if the module is powered on or not (see Table 1 - 4, on page 1 - 11/ Table 1 - 3, on page 1 - 9). 802.11 b/g USB WLAN Module If you have included an 802.
Windows XP Information Network Connection Use the Windows Network Connections control panel to access available wireless networks (Start > Settings > Network Connections or Start > Connect To > Show all Connections). Figure E - 22 Wireless Network Control Panels E 802.
Windows XP Information Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Bluetooth Module The operating system’s Bluetooth Devices control panel is used to configure the Bluetooth settings in Windows XP, and therefore does not require a driver.
Windows XP Information Bluetooth Local Area Connection Icon If you want to display the Local Area Connection icon for the Bluetooth connection in the taskbar, set it up as follows: 1. 2. 3. 4. Access the Network Connections control panel in Windows (Start > Settings > Network Connections OR Start > Connect To > Show all Connections) or by clicking the taskbar icon . Right-click the Bluetooth connection icon, and select Properties.
Windows XP Information Bluetooth Configuration in Windows XP Bluetooth Taskbar Icon If you cannot see the Bluetooth icon in the taskbar, access the Bluetooth Devices control panel. Click Options (tab), and make sure that Show Bluetooth icon in the notification area check box has a tick inside it. Setup your Bluetooth Device so the Computer Can Find it 1. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. 2. Make the device discoverable (to do this check your device documentation).
Windows XP Information To Add a Bluetooth Device 1. 2. 3. 4. 5. Access the Bluetooth Devices control panel. Click Options (tab), and make sure that Allow Bluetooth devices to connect to this computer check box (Connections) has a tick inside it. Click Devices (tab), and then click Add. The Add Bluetooth Device Wizard will appear. Click to select “My device is set up and ready to be found”, and then click Next. Figure E - 25 Add Bluetooth Device Wizard Passkey Options 6. 7. 8.
Windows XP Information To Change Settings for the Bluetooth Device 1. Access the Bluetooth Devices control panel. 2. Click on the device you want to change and click Properties to: • • Change the name of the device (click General, type a new name and click OK). Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK). To Make your Computer Discoverable to Bluetooth Devices 1. Access the Bluetooth Devices control panel. 2.
Windows XP Information PC Camera Module There are 2 camera options available for this computer, depending on your purchase configuration. The 1.3M pixel camera module uses the BisonCap application to capture video files, and the 2.0M pixel camera module uses the VideoView application to capture video files. Before installing the PC Camera driver, make sure that the optional PC Camera is on. Use the Fn + F10 key combination (see Table 1 - 4, on page 1 - 11) to toggle power to the PC Camera module.
Windows XP Information Resuming from Power Saving & PC Camera After the system resumes from Sleep or Hibernate, you will need to use the Fn + F10 key combination to power on the PC Camera before running the PC Camera application. PC Camera Driver Installation 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual CD-ROM into the CD/DVD drive. 2. Click Option Drivers (button), and then click 2.Install PC Camera Driver > Yes. For the 1.
Windows XP Information PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows (see Figure E - 6 on page E - 9). Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then double-click the Sounds & Audio Devices icon (Sounds, Speech, and Audio Devices in Category View). 2. Click Advanced in the Volume > Device volume tab. 3. Click Options and scroll down and click Properties. 4.
Windows XP Information Pre-Allocating File Space You may pre-allocate the file size (File > Allocate File Space) for the capture file in the BisonCap/VideoView program. Pre-allocating space on the hard disk can improve the capture quality (particularly of large capture files), by reducing the amount of work the hard disk has to do in finding space for the video data as it is being captured. E See also “Reducing Video File Size” on page E - 51. BisonCap (1.3M Cam)/VideoView (2.
Windows XP Information Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties) If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Windows XP Information Eliminating Screen Flicker If you find that the video screen in the BisonCap/VideoView program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. Run the BisonCap/VideoView program. 2. Go to Options and scroll down to select Video Capture Filter.... For Bison Cap: 3. Click either 50Hz or 60Hz under Frequency in Property Page (tab). For VideoView: 4. Click either 50Hz or 60Hz under Flickering Reduction in Image (tab).
Windows XP Information Zoom The BisonCap and VideoView programs allow you to zoom the camera in and out. 1. Run the BisonCap/VideoView program. For Bison Cap: 2. Go to Zoom and select Zoom Out/Zoom In. For VideoView: 3. Go to Options and scroll down to select Setting (Use the slider to adjust the zoom level, and click OK to save the setting). Bison Cap VideoView Figure E - 29 Zoom/Setting Snapshot Folder The Snapshot folder’s default location is on the desktop.
Windows XP Information Fingerprint Reader Help & Manual If you have included the fingerprint reader in your purchase option you will need to install the driver as per the instructions below. Right-click the taskbar icon to bring up the menu to select Help. Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full security protection. Help may also be accessed from the Fingerprint Control Center.
Windows XP Information User Enrollment 1. 2. 3. Click Start > Programs/All Programs > Protector Suite QL > User Enrollment, or double click the taskbar icon . On the first run of the program you will be asked to click the button to accept the license, and then click OK. Click Next and select “Enrollment to the hard disk”, and click Finish. Figure E - 30 Enroll to Hard Disk 4. 5. 6.
Windows XP Information Fingerprint Enrollment Note that it is strongly recommended that you enroll more than one finger in case of injury etc. 7. Click the button above any of the fingers to begin the enrollment process for that finger. 8. Swipe the finger three times to enroll that finger. 9. Repeat the process for all the fingers you wish to enroll (see sidebar), and then click Next. 10. Click Finish. 11. Click any of the headings under “Learn more about:” to get more information on any topic. 12.
Windows XP Information 14. Right-click the taskbar icon to bring up the menu that allows you to Edit Fingerprints, Start Control Center, access the Help menu etc. You can also run the Control Center etc. from the Protector Suite QL item in the Programs/All Programs menu. Figure E - 32 Control Center & Biomenu 15. See “Help & Manual” on page E - 54 for further details. 16.
Windows XP Information E E - 58
