V09.4.
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place it on an unstable surface. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company. • The power adapter may have either a 2-prong or a 3-prong grounded plug.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface XIV
Preface Contents Notice .................................................................................I FCC Statement ..................................................................II FCC RF Radiation Exposure Statement: ........................ III Instructions for Care and Operation ................................ V Power Safety ..................................................................VII Battery Precautions ...................................................... VIII Cleaning ............
Preface Hard Disk Drive .............................................................2-2 Optical (CD/DVD) Device ............................................2-3 Loading Discs ................................................................2-3 Handling CDs or DVDs .................................................2-4 DVD Regional Codes ....................................................2-5 7-in-1 Card Reader ........................................................2-6 ExpressCard Slot ........................
Preface TouchPad .......................................................................4-6 CardReader ....................................................................4-6 Hot Key ..........................................................................4-6 Audio .............................................................................4-6 Windows Experience Index ...........................................4-7 Optional Drivers ............................................................
Preface Bluetooth Configuration in Windows Vista ..................7-7 Wireless LAN Module .................................................7-10 802.11b/g/n Driver Installation ....................................7-10 Connecting to a Wireless Network in Windows 7 .......7-11 Connecting to a Wireless Network ..............................7-14 Windows Mobility Center ...........................................7-17 PC Camera Module ......................................................
Preface Display .......................................................................... C-2 Video Adapter ............................................................... C-2 BIOS ............................................................................. C-2 Storage .......................................................................... C-2 Audio ............................................................................ C-2 Keyboard & Pointing Device ........................................
Preface XX
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 • Chapter 3 • Chapter 4 • Chapter 5 • Chapter 6 • Chapter 7 • Chapter 8 • Appendix A • Appendix B • Appendix C • Appendix D A guide to using some of the main features of the computer e.g.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a of interest to you.
Quick Start Guide Not Included Operating Systems (e.g. Windows 7/Windows Vista) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1.
1 Quick Start Guide System Startup 1. 2. 3. 4. 5. Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
Quick Start Guide Operating System Setup If you are installing new system software, or are re-configuring your computer for a different system, make sure you configure the appropriate OS setting in the BIOS before installing a new operating system (Note: If you have installed the Windows Vista/Windows 7 operating system with AHCI mode enabled, DO NOT disable AHCI mode or you will need to reinstall the Windows Vista OS). 1. Start-up the computer and press to enter the BIOS. 2.
1 Quick Start Guide Operating Systems Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the following operating systems are supported.
Quick Start Guide Model Differences This notebook series includes Three different model types that differ as indicated in the table below (see Appendix D for specification details and note that model colors may differ from those pictured). Feature Model A Model B Model C Display Type Supported 14.1" WXGA (1280 * 800) TFT LCD 15.6" HD 16:9 Wide Screen (1366 * 768)TFT LCD 17.
1 Quick Start Guide Figure 1 - 3 LCD Panel Open (Model A) 1. 2. 3. 4. 5. 6. 7. 8. 9. System Map: LCD Panel Open - Model A 1 Wireless Device Operation Aboard Aircraft Built-In PC Camera (Optional) LCD Speakers Power Button Hot Key Buttons Keyboard Built-In Microphone Touchpad & Buttons LED Indicators 2 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
Quick Start Guide System Map: LCD Panel Open - Model B 1 Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 2 3 3 5 4 6 Figure 1 - 4 LCD Panel Open (Model B) Use the key combinations to toggle power to the 3.
1 Quick Start Guide Figure 1 - 5 LCD Panel Open (Model C) 1. 2. 3. 4. 5. 6. 7. 8. System Map: LCD Panel Open - Model C 1 Wireless Device Operation Aboard Aircraft Built-In PC Camera (Optional) LCD Power Button Hot Key Buttons Keyboard Built-In Microphone Touchpad & Buttons LED Indicators The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
Quick Start Guide LED Indicators Icon The LED indicators on the computer display helpful information about the current status of the computer.
1 Quick Start Guide Hot Key Buttons These buttons give instant access to the default Internet browser and e-mail program, and allow you to toggle the Silent Mode on/off with one quick button press. Hot Key Function Activate the Default E-Mail Browser Activate the Default Internet Program Toggle *Silent Mode (for power saving) Table 1 - 5 - Hot Key Buttons *When enabled, Silent Mode will reduce fan noise and save power consumption. Note this may reduce computer performance.
Quick Start Guide Keyboard - Model A The keyboard has a numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly. See Table 1 - 6, on page 1 - 16 for full function key combination details. Function Keys NumLk & ScrLk Keys Play/Pause Key Numerical Keypad 3.75G/HSPA Module Power Toggle Key Fn Key Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard.
1 Quick Start Guide Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/ hot-keys unique to the system’s regular keyboard may not work. Keyboard - Model B The keyboard has a numerical keypad on the right for easy numeric data input, and features function keys to allow you to change operational features instantly.
Quick Start Guide Keyboard - Model C The keyboard has a numerical keypad on the right for easy numeric data input, and features function keys to allow you to change operational features instantly. See Table 1 - 6, on page 1 - 16 for full function key combination details. Function Keys NumLk & ScrLk Keys Play/Pause Key 3.75G/HSPA Module Power Toggle Key Numerical Keypad Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard.
1 Quick Start Guide Function/Hot Key Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility is installed. Fn Keys Function Fn Keys Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F5/F6 Fn + _ Fn + F1 Fn + F2 Fn + F3 Function Volume Decrease/Increase 3.
Quick Start Guide System Map: Front & Left Views Figure 1 - 9 Front & Left Views 1 1. 2. 3. 8 2 3 4 5 6 7 7 9 4. 5. 6. 7. 8. 7-in-1 Card Reader The card reader allows you to use the most popular digital storage card formats: MMC (MultiMedia Card) / SD (Secure Digital) / MS (Memory Stick) / MS Pro (Memory Stick Pro) / MS Duo (requires PC adapter) / Mini SD (requires PC adapter) / RS MMC (requires PC adapter) 9.
1 Quick Start Guide Figure 1 - 10 Right & Rear Views 1. 2. 3. 4. 5. 6. 7. S/PDIF-Out Jack Microphone-In Jack Headphone-Out Jack USB 2.0 Port Optical Device Drive Bay (for CD/DVD Device) Security Lock Slot Battery Disk Eject Warning Don’t try to eject a CD/ DVD while the system is accessing it. This may cause the system to “crash”. Stop the disk first then eject it, or press the stop button twice.
Quick Start Guide System Map: Bottom View - Model A Figure 1 - 11 Bottom View (Model A) 1 2 Battery Information Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 14 for full instructions. 1. 2. 3. 4 3 4. 5. 5 4 Battery Bluetooth Module Cover RAM & CPU Bay Cover Vent/Fan Intake/ Outlet Hard Disk Bay Cover Note: the 3.
1 Quick Start Guide Figure 1 - 12 Bottom View (Model B) 1. 2. 3. 4. Battery RAM & CPU Bay Cover Vent/Fan Intake/ Outlet Hard Disk Bay Cover Note: the 3.75G/HSPA USIM Card is located under the RAM & CPU Bay Cover. System Map: Bottom View - Model B 1 Battery Information Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Quick Start Guide System Map: Bottom View - Model C Figure 1 - 13 Bottom View (Model C) 1 Battery Information 3 Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 14 for full instructions. 2 1. 2. 3 3. 4. 3 5 4 6 6 5. 6. Battery RAM & CPU Bay Cover Vent/Fan Intake/ Outlet Hard Disk Bay Cover 3.
1 Quick Start Guide Windows 7 Start Menu & Control Panel Most of the control panels, utilities and programs within Windows 7 (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
Quick Start Guide Windows Vista Start Menu & Control Panel Windows Vista has a similar Start menu and set of control panels to that of Windows 7. To see all the Windows Vista controls it may be necessary to toggle to Classic View on.
1 Quick Start Guide Video Features - Win 7 You can configure display options from the Display control panel in Windows, and from the ATI Catalyst Control Center as long as the appropriate video driver is installed. For more detailed video information see “ATI Video Driver Controls” on page B - 1. To access Display (Control Panel) and Screen Resolution in Windows: 1. 2. 3. Click Start and click Control Panel. Click Display (icon) - In the Appearances and Personalization category.
Quick Start Guide Screen Resolution & ATI Catalyst Control Center - Win 7 Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display as your display device.
1 Quick Start Guide Video Features - Win Vista You can configure display options, from the Display Settings control panel in Windows as long as the appropriate video driver is installed. For more detailed video information see “ATI Video Driver Controls” on page B - 1. To access Display Settings in Windows: To access Display Settings in Windows: 1. Click Start, and click Control Panel (or point to Settings and click Control Panel). 2.
Quick Start Guide Display Settings & ATI Catalyst Control Center - Win Vista Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display as your display device. 4 1 5 2 3 Video Card Options Note that card types, specifications and drivers are subject to continual updates and changes. Check with your service center for the latest details on video cards supported.
1 Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 22/1 - 23) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • • Hard Disk Drive Optical (CD/DVD) Device 7-in-1 Card Reader ExpressCard Slot TouchPad and Buttons/Mouse Audio Features Adding a Printer Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Figure 2 - 1 Hard Disk Location 2 - 2 Hard Disk Drive Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 2). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 12).
Features & Components 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Features & Components DVD Regional Codes 2 To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - 18. .
Features & Components 2 Card Reader Cover Make sure you keep the rubber cover provided in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. 7-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the Card Reader driver (see “CardReader” on page 4 - 6).
Features & Components ExpressCard Slot The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards). Make sure you install the Card Reader driver (see “CardReader” on page 4 - 6). ExpressCard/54 is used for applications which require a larger interface slot, e.g. CompactFlash card reader. The number denotes the card width; 54mm for the Express Card/54 and 34mm for the ExpressCard/34.
Features & Components 2 TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. There are two TouchPad drivers available for this computer model series depending on your computer model. The following pages contain information on both drivers. Note that the Model C TouchPad supports multi-gesture configuration.
Features & Components Touchpad for Model A & B Computers Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 6) you can configure the functions by double-clicking the TouchPad driver icon in the taskbar. You may then configure the buttons, pointers and finger-sensing pad options to your preferences. Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions.
Features & Components 2 Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details. Touchpad for Model C Computers Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 6) you can configure the functions by double-clicking the TouchPad driver icon on the taskbar.
Features & Components Gestures and Device Settings The Synaptics Gestures Suite application allows you to use a specific gesture (action) on the surface of the TouchPad to perform specific actions to manipulate documents, objects and applications. You can configure the settings from the Device Settings tab in Mouse Properties: 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Mouse (Hardware and Sound). Click Device Settings (tab) and click Settings.
Features & Components Scrolling The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the TouchPad surface and slide both fingers in the direction required (in a straight continuous motion). 2 Figure 2 - 9 Scrolling Gesture Zooming The Pinch Zoom gesture can be used to perform the same function as a scroll wheel in Windows applications that support CTRL + scroll wheel zoom functionality.
Features & Components Rotating Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the TouchPad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.
Features & Components 2 Sound Volume Adjustment The sound volume level is set using the volume control within Windows (and the volume function keys on the computer). Click the volume icon in the taskbar to check the setting. Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/ control panel (right-click the taskbar icon bring up an audio menu).
Features & Components If you have connected an HDMI supported display device to the HDMI-Out port, and additional control panel tab will appear in the Realtek HD Audio Manager. See “HDMI Audio Configuration” on page B - 7 for a description of the audio configuration when connecting an HDMI supported display device.
Features & Components 2 Parallel Printer After setting up the printer attach the parallel cable to the printer. Connect the printer’s parallel cable to the Parallel to USB converter, and then plug the converter into the USB port. Turn ON the printer, then turn ON the computer. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions. Adding a Printer The most commonly used peripheral is a printer.
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management 3 The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. Silent Mode Use the key to toggle Silent Mode to reduce fan noise and save power consumption. Note this may reduce computer performance. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-in jack on the left of the computer.
Power Management Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.
Power Management 3 Resuming Operation See Table 3 - 1, on page 3 - 13 for information on how to resume from a power-saving state. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 1 Power Plan Advanced Settings (Win 7) 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source.
Power Management 3 Figure 3 - 3 Power Plan Advanced Settings (Win Vista) 3 - 6 Power Plans
Power Management Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one. The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity. Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source.
Power Management 3 Figure 3 - 6 Power Plan Advanced Settings (Win Vista) Power Plans 3 - 9
Power Management Power-Saving States 3 You can use power-saving states to stop the computer’s operation and restart where you left off. Win 7/ Win Vista use the Sleep, Hibernate and Shut Down power-saving states. Sleep In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management 3 Password Protection It is recommended that you enable a password on wake up in order to protect your data. Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu.
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo). Power Status Icon To Resume Color Power Off Off Press the Power Button Sleep Blinking Green Press the Power Button Closing the Lid If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up.
Power Management 3 Low Battery Warning When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted. Battery Information Follow these simple guidelines to get the best use out of your battery. Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g.
Power Management Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter. • Reduce the amount of time before the display is turned off. • Close wireless, Bluetooth, modem or communication applications when they are not being used.
Power Management Battery Life 3 Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason see “Removing the Battery” on page 6 - 3. New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page 3 - 18 for instructions on how to do this).
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Caution Danger of explosion if battery is incorrectly replaced. Damaged Battery Warning Should you notice any physical defects (e.g.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 3 1. 2. Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 3. Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options.
Power Management How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Power Management 3 3 - 22 Battery Information
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers/Option Drivers (button). 2. 4 If you wish to install the drivers manually see overleaf for the driver path information. 3. Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below.
Drivers & Utilities Driver - Win 7/Windows Vista (SP2) Page Video Page 4 - 5 LAN Page 4 - 6 TouchPad Page 4 - 6 CardReader Page 4 - 6 Hot Key Page 4 - 6 Audio Page 4 - 6 PC Camera Module Page 7 - 19 Wireless LAN Module Page 7 - 10 3.75G/HSPA Module Page 7 - 27 Table 4 - 1 - Driver Installation Manual Driver Installation Click Browse CD/DVD (button) in the Drivers Installer application and browse to the executable file in the appropriate driver folder.
Drivers & Utilities 4 Updating/Reinstalling Individual Drivers User Account Control If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Programs > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer).
Drivers & Utilities New Hardware Found Driver Installation Procedure If you see the message “New Hardware Found” during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure. Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button).
Drivers & Utilities 4 LAN 1. Click 2.Install LAN Driver > Yes. 2. Click Install. 3. Click Finish. 4. The network settings can now be configured. TouchPad 1. Click 3.Install Touchpad Driver > Yes. 2. Choose the language you prefer and click OK. 3. Click Next. 4. Click Finish > Restart Now to restart the computer. CardReader 1. Click 4.Install CardReader Driver > Yes. 2. Click Install. 3. Click Finish. Hot Key 1. Click 5.Install Hotkey Utility > Yes. 2. Click Next > Install. 3.
Drivers & Utilities Windows Experience Index After the drivers are installed follow this procedure to ensure an accurate rating from the Windows Experience Index (make sure the AC/DC adapter is plugged in): For Windows 7: 1. Click Start, and click Control Panel. 2. Click Performance Information and Tools (System and Security > System > Check the Windows Experience Index). 3. Click “Rate this computer/Refresh Now/Rerun the assessment”. 4.
Drivers & Utilities Optional Drivers Bluetooth Module See the pages indicated for the driver installation procedures for any modules included in your purchase option. Note: The operating system is the default setting for Bluetooth control in Windows Vista, and does not require a driver. See “Bluetooth Module” on page 7 - 2 for configuration instructions. 4 Wireless LAN Module See the introduction in “Wireless LAN Module” on page 7 - 10, and check the installation procedure.
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make.
BIOS Utilities POST Screen 5 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST Note: The POST screen as pictured right is for guideline purposes only. The POST screen on your computer may appear slightly different. If you disable the Boottime Diagnostic Screen, the POST screen will not appear. The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory).
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities The Setup Program The Phoenix Setup program tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup 5 To enter Setup, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few seconds after you turn on the system. If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu PhoenixBIOS Setup Utility Figure 5 - 2 Main Mai n Advanced Security Boot Exit Main Menu Item Specific Help 5 System Time: System Date: [22:12:05] [09/07/2009] SATA Port 1 SATA Port 3 [FUJITSU MHY2120BH-(S] [HL-DT-ST DVDRAM GSA-] System Memory Extended Memory 633 KB 894 MB BIOS Revision KBC/EC Firmware Revision ******** ******** F1 Esc Help Exit Select Item Select Menu -/+ Enter , , or selects field.
BIOS Utilities SATA Port 1/3 (Main Menu) Pressing Enter opens the sub-menu to show the configuration of an HDD/optical device on the computer’s SATA Port 1/3. Use the Auto (Type:) setting to have the items configured automatically for you. System/Extended Memory (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed.
BIOS Utilities Advanced Menu PhoenixBIOS Setup Utility Main A dvanced Advanced Security Boot Exit Item Specific Help Advanced Chipset Control SATA Mode Selection: Legacy USB Support: Boot-time Diagnostic Screen: Power on Boot Beep: Battery Low Alarm Beep: 5 [AHCI] [Enabled] [Disabled] [Disabled] [Disabled] Figure 5 - 3 Advanced Menu F1 Esc Help Exit Select Item Select Menu -/+ Enter Change Values Select Sub-Menu F9 Setup Defaults F10 Save and Exit Advanced Chipset Control (Advance
BIOS Utilities SATA Mode Selection (Advanced Menu) You can configure SATA (Serial ATA) control to operate in either IDE (native/ compatible) or AHCI (Advanced Host Controller Interface) modes from this menu. The SATA mode should be set to AHCI mode for this system (unless you are sure your hard disk can only operate in IDE mode). If you are unsure of the mode your hard disk supports contact your service center.
BIOS Utilities Security Menu 5 Security Menu PhoenixBIOS Setup Utility Main Figure 5 - 4 5 - 10 Security Menu Security Security Boot Exit Item Specific Help The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS.
BIOS Utilities Set User Password (Security Menu) You can set a password for user mode access to the PhoenixBIOS Setup Utility. This will not affect access to the computer OS, (only the Setup utility) unless you choose to set a Password on Boot (see below). Many menu items in the PhoenixBIOS Setup Utility cannot be modified in user mode. You can only set the user password after you have set the supervisor password.
BIOS Utilities Boot Menu Figure 5 - 5 PhoenixBIOS Setup Utility Main Advanced Security Boot Exit Boot Menu Item Specific Help Boot priority order: 1: USB HDD: 2: IDE CD: 3: IDE 4: FUJITSU MHY2120BH-(S1) 4: USB KEY: 5: PCI BEV: JMC26X Fast Ethernet Contr 6: 7: 8: Excluded from boot order: : USB CDROM: : USB FDC: : PCI SCSI: 5 F1 Esc Help Exit Select Item Select Menu -/+ Enter Keys used to view or configure devices: Up and Down arrows select a device.
BIOS Utilities Exit Menu Figure 5 - 6 PhoenixBIOS Setup Utility Main Advanced Security Boot Exit Exit Menu Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Esc Help Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
BIOS Utilities 5 5 - 14
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. 4. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Slide the battery out in the direction of the arrow 3 .
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CD-ROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer 4. 5. Grip the tab and slide the hard disk in the direction of arrow 4 Lift the hard disk out of the bay 5 . .
Upgrading The Computer 6. 7. Remove the screw(s) 6 and the adhesive cover 7 . Reverse the process to install a new hard disk drive (do not forget to replace all the screws and covers). 6 6 Figure 6 - 4 HDD Cover Removal 6 - 6 Upgrading the Hard Disk Drive 7 Hard Disk Screws & Cover The hard disks and covers pictured here may appear slightly different from your model design (these designs are subject to change and upgrade without notice).
Upgrading The Computer Upgrading the Optical (CD/DVD) Device 1. 2. 3. 4. 5. 6. Turn off the computer, and turn it over and remove the battery. Model A: Locate the RAM & CPU bay cover and remove screws 1 - 3 . Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. Carefully disconnect the fan cable 4 , and remove the cover 5 . OR Models B & C: Locate the hard disk bay cover and loosen screws 1 & 2 . Remove the hard disk bay cover 3 .
Upgrading The Computer 7. 8. Remove the screw at point 6 , and use a screwdriver to carefully push out the optical device at point 7 . Reverse the process to install the new device (make sure you replace the bay cover for Model A computers and align the cover correctly - see “Model A Cover Alignment” on page 6 - 12).
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 200 pin Small Outline Dual In-line (SODIMM) DDRII (DDR2) type memory modules (see “Memory” on page C - 2 for details of supported module types). 1. 2. Turn off the computer, and turn it over and remove the battery. Locate the RAM & CPU bay cover and remove screws 1 - 3 .
Upgrading The Computer 3. 4. Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. Carefully disconnect the fan cable 4 , and remove the cover 5 . Fan Cable & Cover 6 Make sure you reconnect the fan cable 4 before screwing down the bay cover. Note the information on replacing the RAM & CPU bay cover in “Cover Pins” on page 6 - 12. Contact Warning Be careful not to touch the metal pins on the RAM module’s connecting edge.
Upgrading The Computer 5. 6. 7. 8. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 6 & 7 ) in Figure 6 - 9. The RAM module will 8 pop-up, and you can remove it. Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. Figure 6 - 9 6 Model A 7 6 Model B 7 RAM Module Removal 6 Model A Model B 8 9.
Upgrading The Computer Cover Pins 6 Note that Model A computers have four cover pins, Model B computers have five cover pins and Model C computers have four pins. These pins need to be aligned with slots in the case to insure a proper cover fit, before screwing down the bay cover Figure 6 - 10 Cover Pin Alignment 10. Press the module in and down towards the mainboard until the slot levers click into place to secure the module. 11.
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. • • • • Bluetooth Module Wireless LAN Module PC Camera Module 3.75G/HSPA Module Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Bluetooth Module The operating system’s Bluetooth Devices control panel is used to configure the Bluetooth settings in Windows 7/Vista, and therefore does not require a driver.
Modules & Options Bluetooth Configuration in Windows 7 Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). Add a Device To Turn the Bluetooth Module On 1. 2. 3. Press the Fn + F12 key combination to power on the Bluetooth module. A Bluetooth icon will appear in the taskbar.
Modules & Options To Add a Bluetooth Device 1. 2. Access the Bluetooth Devices control panel and click Add a device. Double-click the device you want to pair with the computer. 3. On first connection the computer will provide you with a pairing code to be entered onto the device. Pairing Options 7 If a device has been previously connected then the pairing option menu will appear when you attempt subsequent connections.
Modules & Options 4. Enter the code into your Bluetooth enabled device and follow any on-screen instructions to complete the pairing. Figure 7 - 3 Pairing Codes Pairing Code Example The example outlined here shows a connection to a mobile device. Other devices e.g. computers, may have a slightly different connection procedure, and may require you to confirm a pairing code is correct on both devices. Follow the onscreen instructions to complete the pairing. 5. 6. 7.
Modules & Options To Change Settings for the Bluetooth Device Bluetooth Help 7 To get help on Bluetooth configuration and settings, select Help and Support from the Start menu. Type Bluetooth in the Search Help box, and select an item from the returned search results to get more information. 1. 2. • • Click the taskbar icon and select Show Bluetooth Devices.
Modules & Options Bluetooth Configuration in Windows Vista Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). To Turn the Bluetooth Module On 1. 2. 3. Press the Fn + F12 key combination to power on the Bluetooth module. A Bluetooth icon will appear in the taskbar (see sidebar).
Modules & Options To Add a Bluetooth Device 1. 2. Figure 7 - 7 Add Bluetooth Device Wizard 3. 4. 5. Access the Bluetooth Devices control panel. Click Options (tab), and make sure that Allow Bluetooth devices to connect to this computer check box (Connections) has a tick inside it. Click Devices (tab), and then click Add. The Add Bluetooth Device Wizard will appear. Click to select “My device is set up and ready to be found”, and then click Next. 6. 7. 8.
Modules & Options To Change Settings for the Bluetooth Device 1. 2. Access the Bluetooth Devices control panel. Click on the device you want to change and click Properties to: • • Change the name of the device (click General, type a new name and click OK). Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK). To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3. Access the Bluetooth Devices control panel.
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + F11 key combination to toggle power to the WLAN module, and check the indicator to see if the module is powered on or not (see Table 1 - 6, on page 1 - 16/ Table 1 - 4, on page 1 - 11). Wireless LAN Module If you have included a 802.
Modules & Options Connecting to a Wireless Network in Windows 7 Make sure the Wireless LAN module is turned on. 1. Click the taskbar wireless icon , and then double-click an access point to connect to or click to Open Network and Sharing Center if you do not see a network you want to connect to in the taskbar menu (a list of options will appear allowing setting changes, and creating a new network).
Modules & Options 2. 3. 4. You may need to enter a security key for any access point to which you are trying to connect. Click to select a network location (e.g. Home, Work or Public). Click “View or change settings in Network and Sharing Center” to access further options for the connection.
Modules & Options 5. 6. Click the taskbar icon to see any currently connected networks. To disconnect from the wireless network you can click the taskbar wireless icon , click the active connection and then click Disconnect (button). Security Enabled Networks You should try to make sure that any network you are connecting to is a secure network. Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Modules & Options Connecting to a Wireless Network Make sure the Wireless LAN module is turned on. 1. Click the taskbar wireless icon , and then click Connect to a network (or rightclick the icon , and then click Connect to a network). Figure 7 - 13 Taskbar Menus Click icon Right-click icon 7 Network and Sharing Center 2. 3. In the Show list, click to choose Wireless from the drop-down menu. A list of currently available networks will appear.
Modules & Options 4. 5. Click a network, and then click Connect. If you do not see a network you want to connect to, click Set up a connection or network (a list of options will appear allowing manual searching, and creating a new network). Figure 7 - 15 Connecting 7 6. Move the cursor over the taskbar icon to see the connection status (see below).
Modules & Options 7. Security Enabled Networks To disconnect from the wireless network you can click the taskbar wireless icon , and then select Connect or disconnect to access the network menu, and click Disconnect (or right-click the icon , and then click Disconnect from). You should try to make sure that any network you are connecting to is a secure network. 7 Click icon Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Modules & Options Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center: 1. 2. 3. Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Windows Mobility Center (Mobile PC). Click the button to Turn wireless off/on, or click the icon to access the network menu.
Modules & Options Latest PC Camera Driver Information 7 Check the Device Drivers & Utilities + User’s Manual disc, and any accompanying insert pages, for the latest updated information on the PC Camera driver, which may override the information provided here. PC Camera Module If you have included a PC Camera module in your purchase option, make sure that the PC Camera module is on before installing the driver.
Modules & Options PC Camera Driver Installation 1. Make sure the module is powered on, then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 2.Install Camera Driver > Yes. 4. Choose the language you prefer and click Next > Next (Install). 5. Click Finish to restart the computer. 6.
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. 7 Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Sound (Hardware and Sound). Click Recording (tab). Right-click Microphone (Realtek High Definition Audio) and make sure the item is not disabled. 5. Double-click Microphone (or select Properties from the right-click menu). 6.
Modules & Options Figure 7 - 19 Audio Setup for PC Camera Right-click 7 PC Camera Module 7 - 21
Modules & Options Pre-Allocating File Size/Space 7 You may pre-allocate the file size (File > Allocate File Size/Space) for the capture file in the BisonCap/AveoCap program (you will need to set a folder first for the AveoCap program.) Camera Application The WebCam application is a video viewer for general purpose video viewing and testing, and for capturing video files to .avi format. 1. 2. 3.
Modules & Options Set Capture File Prior to capturing video files you may select the Set Capture File... option in the File menu, and set the file name and location before capture (this will help avoid accidentally overwriting files). Set the name and location then click Open, then set the "Capture file size:" and click OK. You can then start the capture process as on the previous page.
Modules & Options Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Modules & Options Eliminating Screen Flicker If you find that the video screen in the camera program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3. Run the camera application from the desktop shortcut. Go to Options and scroll down to select Video Capture Filter.... Click either 50Hz or 60Hz under Frequency/Anti Flicker in Property Page (tab).
Modules & Options Zoom The WebCam program allows you to zoom the camera in and out. 1. 2. Run the camera application from the desktop shortcut. Go to Zoom and select Zoom Out/Zoom In. Figure 7 - 21 Zoom/Setting 7 Snapshot Folder The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture. Taking Still Pictures The WebCam program allows you to take still pictures. 1. 2. 3.
Modules & Options 3.75G/HSPA Module If you have included an optional 3.75G/HSPA (High Speed Packet Access) module (see “Communication” on page C - 3 for specification details) in your purchase option, you will have the appropriate application (HSPA Modem Interface or Mobile Partner) provided for your particular module. Follow the instructions on page 7 29 to install the USIM card (supplied by your service provider), and then install the application (see over for further details). Important Notice - 3.
Modules & Options 3.75G/HSPA Modules & System Wake Up Note that the 3.75G modules DO NOT support system wake up on 3.75G/HSPA modem activity. 7 Before installing the application, make sure that the 3.75G/HSPA module is ON (installing the driver with the module off will not allow the software to detect the module hardware correctly). Use the Fn + key combination (see “Keyboard Model C” on page 1 - 15) to toggle power to the 3.75G/HSPA module. When the 3.
Modules & Options 1. 2. Turn off the computer, and turn it over and remove the battery. Access the SIMLOCK as follows: • For Models A & B: Locate the RAM & CPU bay cover and remove screws 1 3 (the SIMLOCK is located at point 4 ), then carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. Carefully disconnect the fan cable 5 , and remove the cover. • For Model C: Locate the SIM card cover and loosen screw 6 , and then remove the SIM card cover 7 .
Modules & Options • For Models A & B: Figure 7 - 23 3. 4. 5. Insert the USIM card as you would into your mobile phone. Slide the SIMLOCK towards the hinge in order to release the lock and lift it up. Insert the USIM card as illustrated in (Figure 7 - 23) and close the SIMLOCK. 6. Lock the SIMLOCK by pushing it in the direction of the arrow in Figure 7 - 24 until it clicks into the lock position. Insert the USIM Card 3.75G/HSPA Modules & System Wake Up 7 Note that the 3.
Modules & Options 7. Replace the bay cover (see sidebar) and screws (make sure you reconnect the fan cable before screwing down the bay cover). Cover Pins Model B Model A Model C Fan Cable & Cover Note that Model A computers have four cover pins, Model B computers have five.
Modules & Options • For Model C Figure 7 - 26 8. Insert the USIM card as you would into your mobile phone. 9. Slide the SIMLOCK towards the hinge in order to release the lock and lift it up. 10. Insert the USIM card as illustrated in (Figure 7 - 26) and close the SIMLOCK. Insert the USIM Card 3.75G/HSPA Modules & System Wake Up 7 Note that the 3.75G modules DO NOT support system wake up on 3.75G/HSPA modem activity. 11.
Modules & Options HSPA Modem Interface With the 3.75G/HSPA module and USIM card (supplied by your service provider) installed you may then install the HSPA Modem Interface. The HSPA Modem Interface allows you to directly access your HSPA internet service from the computer. HSPA Modem Interface Installation 1. Enable power to the module by pressing the Fn + key combination (the on screen icon will indicate the module’s power status).
Modules & Options HSPA Modem Interface HSPA Modem Help To get help on 3.75G/ HSPA module configuration and settings, click the help icon and select Help. The connection information is stored on the USIM card supplied by the service provider. 1. 2. 3. 4. 7 5. Power on the 3.75G/HSPA module using the Fn + key combination. Access the HSPA Modem Interface from the Start menu (Start > Programs/All Programs > HSPA Modem > HSPA Modem), or by double-clicking the desktop icon .
Modules & Options 6. Click Connect to connect to your service provider. Figure 7 - 29 Connecting to Network 7. The message “Network is connected” will be displayed when the network connection is successful. Figure 7 - 30 Network is Connected 8. You can then access the internet, download e-mail etc. as per any internet connection. 3.
Modules & Options 9. Figure 7 - 31 While you are connected the upper right corner of the HSPA Modem interface will display the upload and download rates, and the taskbar icon will display the connection information. Uploading/ Downloading Rates and Speed Win Vista Win 7 10. To disconnect click the Disconnect icon (Connection Manager). 11. The program will disconnect from the service provider. 12. The module will still be on, and you will need to press the Fn + key combination to turn it off.
Modules & Options 3. 4. Click Add (button) and input any Network Settings required by your service provider. Click OK to save the profile. Figure 7 - 33 Network Settings & Profiles 7 5. 6. You can Edit or Delete profiles from the Profiles tab. To use a profile click to select it, and then click Apply (button) and the settings will be transferred to Connection Manager. 3.
Modules & Options Contacts 1. 2. Access the HSPA Modem Interface from the Start menu (Start > Programs/All Programs > HSPA Modem > HSPA Modem), or by clicking the desktop icon. Click Contacts (button). Figure 7 - 34 Network Settings & Profiles 7 3. 4. 5. 6. Click Refresh (button) to download the contacts from the USIM card to the computer. The Contacts will then be displayed. Double-click any contact to edit the information (or right-click and select Edit).
Modules & Options Messages 1. 2. Access the HSPA Modem Interface from the Start menu (Start > Programs/All Programs > HSPA Modem > HSPA Modem), or by clicking the desktop icon. Click Messages (button). SMS Service In addition to standard internet services you may also send and receive SMS text messages using the HSPA Modem Interface, if your service supports SMS. 7 Figure 7 - 35 Network Settings & Profiles 3. 4. 5. Click Refresh (button) to download the messages from the USIM card to the computer.
Modules & Options 6. 7. 8. Click to select a contact from the list and then click Add (button) and the phone number will automatically be added to the recipient field. Type the message information into the message body and click Send (button) to send it, or Save to draft (button) to save the message. Select any message to forward or delete it, or to reply to it. Settings 1. 2.
Modules & Options 3. 4. 5. Click OK alongside any of the options to configure the settings. The Network can be configured for an Automatic (usually from the USIM card) or Manual connection. The Network Mode can be configured for any appropriate mode required. Figure 7 - 37 Settings - Network/ Network Mode 6. 7. 8. You can also change your settings for the Pin #, and input your phone number. Exiting the program DOES NOT turn off the 3.
Modules & Options Mobile Partner Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + key combination to toggle power to the 3.75G/HSPA module, and check the indicator to see if the module is powered on or not (see Table 1 - 6, on page 1 - 16/ Table 1 - 4, on page 1 - 11). With the 3.
Modules & Options Mobile Partner Application You will need to contact your service provider to obtain the exact details of how exactly to configure the settings on this page. Profile Management 1. 2. 3. 4. 5. Power on the 3.75G/HSPA module using the Fn + key combination. Access the Mobile Partner application from the Start menu (Start > Programs/ All Programs > Mobile Partner), or by double-clicking the Mobile Partner icon on the desktop .
Modules & Options Connecting to the Service Provider 1. 2. 3. 4. Power on the 3.75G/HSPA module using the Fn + key combination. Access the Mobile Partner application from the Start menu (Start > Programs/ All Programs > Mobile Partner), or by double-clicking the Mobile Partner icon on the desktop . The software will run and you can select the Profile Name from the menu. Click Connect to begin the connection process. 5. The Mobile Partner application will then display the connection information.
Modules & Options 6. When the connection is successful you can move the cursor over the network icon in the taskbar to display the connection information. Win Vista Win 7 Figure 7 - 41 Connected Taskbar Notification 7 7. 8. You can then access the internet, download e-mail etc. as per any internet connection. While you are connected the indicators in the Mobile Partner window will display uploading and downloading icons and a network icon in the taskbar . 3.
Modules & Options 9. To disconnect click the Disconnect and select Disconnect. icon, or right click the taskbar icon Win Vista Figure 7 - 42 Disconnect Win 7 7 10. The program will disconnect from the service provider. 11. The module will still be on, and you will need to press the Fn + to turn it off. 7 - 46 3.
Modules & Options 12. If you click the Mobile Partner close icon a message will be displayed asking you to click OK to confirm the program exit and to terminate the connection. Figure 7 - 43 Exit Prompt 13. Exiting the program terminates the connection, but DOES NOT turn off the 3.75G/ HSPA module, and you will need to press the Fn + key combination to turn off the module (pay careful attention to this aboard aircraft - see “Wireless Device Operation Aboard Aircraft” on page 7 - 42). 14.
Modules & Options Text Messaging Service In addition to standard internet services you may also send and receive SMS text messages using the Mobile Partner program, if your service supports SMS. Reading SMS Messages 1. 2. 3. 4. 7 An icon will blink at the bottom of the Mobile Partner interface to notify you of any new messages received. Click the Text icon in the Mobile Partner Interface. Select the Local > Inbox or SIM/USIM Card folder and select any message to read it.
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “LED Indicators” on page 1 - 11) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED power indicator blinking orange. , is Low Battery. Plug in the DC power source.
Troubleshooting Problem The computer feels too hot. Possible Cause - Solution Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 20). Make sure you’re using the correct adapter.
Troubleshooting Problem Possible Cause - Solution You forget the boot password. If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Problem Possible Cause - Solution Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work. 8 The system freezes or the screen goes dark. The system’s power saving features have timed-out.
Troubleshooting Problem Possible Cause - Solution The PC Camera module cannot be detected. The module is off. Press the Fn + F10 key combination in order to enable the module (see “Function/Hot Key Indicators” on page 1 - 16/). Run the PC Camera application to view the camera picture. The Wireless LAN/Bluetooth/ PC Camera/3.75G/HSPA modules cannot be configured. The driver(s) for the module(s) have not been installed.
Troubleshooting Screen Resolution Error If you are experiencing either screen resolution reduction, or screen flickering after resuming from Sleep in Windows Vista only then follow the instructions below to fix this problem. This error arises in compliance with Windows Vista policy, which triggers TMM (Transient Multi-Monitor Manager) when the notebook lid (S3) is closed. TMM disconnects the LCD display from the OS and then adds the LCD display back when the lid is opened.
Troubleshooting 3. 4. 5. Double-click Task Scheduler Library > Microsoft > Windows. Click MobilePC to open the control panel. Right-click TMM and select Disable. 8 Figure 8 - 2 - TMM Disable 6. Close all the control panels.
Troubleshooting 8 8 - 14
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer. External Monitor (VGA) Port This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD.
Interface (Ports & Jacks) Item Description Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. S/PDIF-Out Jack This S/PDIF (Sony/Philips Digital Interface Format) Out Jack allows you to connect your DVDcapable PC to a Dolby AC-3 compatible receiver for “5.1” or ‘dts’ surround sound. USB 2.0/1.1 Ports These USB 2.0 compatible ports (USB 2.0 is fully USB 1.
Interface (Ports & Jacks) A A - 4
Appendix B: ATI Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features - Win 7” on page 1 - 24/“Video Features - Win Vista” on page 1 - 26. Video Card Options ATI Video Driver Installation Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button). 1. Click 1.Install Video Driver > Yes. 2. Click Next > Install (button). 3.
ATI Catalyst® Control Center Adjust the video settings from the ATI Catalyst® Control Center. ATI Taskbar Icon The ATI Catalyst Control Center can be accessed as above or by double-clicking the icon in the taskbar (or by right-clicking the icon and selecting Catalyst Control Center). If you don’t see the ATI icon in the taskbar, click Preferences (tab) in the ATI Catalyst® Control Center, and select Enable System Tray Menu. B 1. 2. 3. 4. 5.
The ATI Catalyst® Control Center provides additional video configuration controls and tools which allow quick access to features such as display options, 3D Settings, color and Help menus etc. Adjust settings from the options in the Graphics Settings Tree View pane. Help Menus Click Help (tab) and select an option from the drop down menu. Press F1 to bring up Help for any currently selected page.
Display Devices Function Keys B Besides the built-in You can use the Fn + F7 LCD, you can also use key combination to togan monitor/flat gle external through the display panel options:display as your display device. The fol• Notebook lowing are Only the display •options: External Display Only • Notebook + External • The built-in LCD. Display • An external monitor Give the displays connected to the enough time to refresh. external monitor port.
Configuring an External Display using the ATI Catalyst Control Center Alternatively you can use the ATI Catalyst Control Center to configure any attached displays. 1. 2. 3. 4. 5. 6. 7. Attach your external display to the external monitor port or HDMI-Out port, and turn it on. Go to ATI Catalyst Control Center (see “ATI Catalyst® Control Center” on page B - 2). Select Displays Manager from the Graphics Settings Tree View pane. Attached displays will appear in the Desktop and Display Setup box.
Selecting Display Modes Clone Mode Clone Mode simply shows an exact copy of the Main display desktop on the other display(s). This mode will drive multiple displays with the same content. Use this feature to display the screen through a projector for a presentation. Right-click the attached display icon and select an option (Clone or Extend) from the menu. Figure B - 5 Displays Manager Clone Mode B Click Displays Properties to make adjustments for any attached displays.
Extended Mode In Extended Mode each monitor can be configured separately with the Windows desktop stretched between the two monitors (except the taskbar). This configuration is recommended if you are using two monitors of different size, as you may configure the best resolution, refresh rates and color quality for each display. Click either the Graphics Adapter pop-up menu, or click the icon for the appropriate display. Configure the settings from the Selected Display.... menu.
Video Options Note that card types, specifications and drivers are subject to continual updates and changes. Check with your service center for the latest details on video cards supported. Configuring an External Display in Win 7 1. 2. 3. 4. Attach your external display to the external monitor port/HDMI-Out port and turn it on. Go to the Screen resolution control panel. Click the Detect button. The computer will then detect any attached displays. 5.
Video Options Note that card types, specifications and drivers are subject to continual updates and changes. Check with your service center for the latest details on video cards supported. Figure B - 8 • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) • Extend these displays - Treats both connected displays as separate devices • Show desktop only on 1/2 - Only one of your displays is used.
Using the Windows Logo Key + P Key Combination to Switch Displays You can also use the + P key combination to quickly change display configuration and modes (this is particularly useful when attaching a projector) in Windows 7. 1. 2. 3. 4. Attach your external display to the external monitor port and turn it on. Press the + P key combination. An on-screen menu will pop up. Use the cursor keys (or + P) to select the appropriate configuration from the menu, and press Enter to confirm the selection.
Configuring an External Display in Win Vista 1. 2. 3. Attach your external display to the external monitor port or HDMI-Out port, and turn it on. If a New Display Detected window does not appear in Windows Vista, go to the Windows Mobility Center control panel (Mobile PC > Adjust commonly used mobility settings) and click Connect display. Click on any of the buttons to configure the displays to your preferences, or click Display Settings (in the New Display Detected window) to access the control panel.
Using New Display Detected to Enable Extended Mode 1. Display Settings Extended Desktop 2. Use the control panel to drag the monitors to match the physical arrangement you wish to use. 3. 4. 5. Attach your external display to the external monitor port or HDMI-Out port, and turn it on. If a New Display Detected window does not appear in Windows Vista, go to the Windows Mobility Center control panel (Mobile PC > Adjust commonly used mobility settings) and click Connect display.
Using Display Settings to Enable Extended Mode 1. 2. 3. Attach your external display to the external monitor port or HDMI-Out port, and turn it on. Open Display Settings (see “Video Features - Win Vista” on page 1 - 26) control panel. Click the monitor icon (e.g. 2 ), and make sure you have checked “Extend the desktop onto this monitor” and click Apply. Click the appropriate monitor icon (e.g. 2 ) to be able to select the option to extend the desktop on to it.
HDMI Audio Configuration As HDMI (High-Definition Multimedia Interface) carries both audio and video signals you will need to configure the audio output as per the instructions below on initial connection. Initial Windows Audio Setup for HDMI 1. 2. 3. 4. 5. 6. Connect a display device with HDMI support to the HDMI-Out port. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Playback (tab), and click to select Realtek HDMI Output.
HDMI Notes • Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device. HDMI Video Configuration 1. 2. 3. 4. Connect an HDMI cable from the HDMI-Out port to your external display. Configure your external display as per the instructions in “Configuring an External Display using the ATI Catalyst Control Center” on page B - 5. Set up your external display (TV or LCD) for HDMI input (see your display device manual).
Theater Mode Theater Mode enables you to display video playback in full screen on a secondary monitor. Theater Mode can be configured from the Avivo™ Video > Theater Mode tab in the Graphics Settings Tree View pane.
PowerPlay™ PowerPlay™ in the Graphics Settings Tree View pane allows you to set your graphics processor settings for higher performance or longer battery life.
B B - 18
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your service center for details.
Specifications Processor Display Storage AMD® Athlon™ 64 Processor: TF20 (1.6GHz) 65nm (65 Nanometer) Process Technology, 512KB L2 Cache & FSB 533MHz - TDP 15W 638 Pin, µPGA Package - Socket S1G1 Model A Computers: 14.1 (35.81cm) WXGA (1280 * 800) TFT LCD One Changeable 12.7mm(h) Optical Device (CD/DVD) Type Drive (see “Optional” on page C - 4) X2 Dual-Core TK-42 (1.
Specifications Interface Communication Power Three USB 2.0 Ports One Headphone-Out Jack One Microphone-In Jack One S/PDIF-Out Jack One RJ-45 LAN Jack One DC-In Jack One External Monitor Port One HDMI-Out Port Built-In 10/100Mb Base-TX Ethernet LAN Full Range AC/DC Adapter AC input 100 - 240V, 50 - 60Hz, DC Output 19V, 3.42A OR 18V, 3.5A (65 Watts) 6 Cell Smart Lithium-Ion Battery Pack, 48.84WH 9 Cell Smart Lithium-Ion Battery Pack, 73.
Specifications Dimensions & Weight Optional Model A Computers: 336mm (w) * 250mm (d) * 24.8 - 35.7mm (h) 2.2 kg With 6 Cell Battery & ODD Super Multi Optical Device Drive Module Model B Computers: 374mm (w) * 256mm (d) * 25 - 37.9mm (h) 2.7 kg With 6 Cell Battery & ODD Model C Computers: 397.2mm (w) * 282.5mm (d) * 39.5mm (h) 2.
