M M77V VIIT T FCC Statement and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
C Coonntteennttss ENGLISH..................................................................................................... 1 M7VIT Features .................................................................................................................. 1 Package contents .............................................................................................................. 2 Layout of M7VIT..........................................................................................................
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn English M7VIT Features Use VIA VT8377 (KT400)/ VT8235 Chipset, Winbond W83697HF. Contains on board I/O facilities, which include two serial ports, a parallel port, a PS/2 mouse port, a PS/2 keyboard port, audio ports, USB ports, a game port. Supports Single Socket-A for an AMD Athlon/ Duron Family processor, running at 200/266/333 MHz Front Side Bus frequency.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Support Front Audio pin head functions. CMI 8738 Hardware Audio Features (Optional): * 6CH DAC for AC3® 5.1CH purpose. * HRTF-based 3D positional audio, supporting DirectSound™ 3D and A3D™ interface. * Supports 4.1/5.1 speakers, C3DX positional audio in 4/ 6 CH speaker mode. * MPU-401 port. * Built-in ZV port.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Layout of M7VIT 1 JKBV1 JUSBV1 Socket A 1 CPU 1 VT8377 (KT400) GAME Port MIC-IN LINE-IN SP-OUT JATXPWR1 1 JGAME1 JAUDIO1 IDE1 IDE2 Winbond I/O 1 AGP SLOT BAT1 PCI1 PCI SLOT BIOS 1 1 PCI2 PCI SLOT 4 6 1 3 JUSB2 Codec PCI3 PCI SLOT 2 10 1 9 VT8235 JUSB3 2 PCI4 Hardware Audio JCMOS1 PCI SLOT 1 1 10 9 JUSBV2 PCI5 PCI SLOT CNR SLOT FDD1 JWOL1 1 JPANEL1 1 CNR1 JSFAN1 3 2 1 24 23
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn CPU Installation CP U 1. Pull the lever sideways away from the socket then raise the lever up to 90-degree angle. 2. Locate Pin A in the socket and lock for the white dot or cut edge in the CPU. Match Pin A with the white dot/cut edge then insert the CPU. 3. Press the lever down. Then Put the fan on the CPU and buckle it and put the fan’s power port into the JCFAN1, then to complete the installation.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn DDR DIMM Modules: DIMM1-2-3 DRAM Access Time: 2.5V Unbuffered/ Registered DDR 1600/ 2100/ 2700/ 3200 Type required. DRAM Type: 64MB/ 128MB/ 256MB/ 512MB/ 1GB DIMM Module (184 pin) Only support 4 bank for DDR PC3200 (2pcs Double-Side or 3 pcs Single-Side).
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn How to install a DIMM Module 1. The DIMM socket has a “ Plastic Safety Tab”, and the DIMM memory module has an “Asymmetrical notch”, so the DIMM memory module can only fit into the slot in one direction. 2. Push the tabs out. Insert the DIMM memory modules into the socket at a 90-degree angle, then push down vertically so that it will fit into the place. 3. The Mounting Holes and plastic tabs should fit over the edge and hold the DIMM memory modules in place.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Jumpers, Headers, Connectors & Slots Hard Disk Connectors: IDE1/ IDE2 The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO Mode 0~4, Bus Master, and Ultra DMA 33/ 66/ 100/ 133 functionality. It has two HDD connectors IDE1 (primary), IDE2 (secondary) and IDE3. The IDE connectors can connect a master and a slave drive, so you can connect up to four hard disk drives. The first hard drive should always be connected to IDE1.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Power Connectors: JATXPWR1 JATXPWR1 JATXPWR1 (ATX Main Power Conn.) (ATX Power Conn.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Front Panel Connector: JPANEL1 PWR_LED SLP (+) (+) (-) ON/OFF IR 24 2 23 1 SPK (+) (-) RST HLED IR SPK ==> Speaker Conn. HLED ==> Hard Driver LED RST ==> Reset Button IR ==> Infrared Conn.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Audio Subsystem: JAUDIO1/ JCDIN1 1 2 2 1 1 1 9 10 JAUDIO1 JCDIN1 (Front Audio Header) (CD-ROM Audio-In Header) 1 2 Pin1 Pin3 Pin5 Pin7 JAUDIO1 Pin9 ==> Mic In Pin2 ==> Ground ==> Mic Power Pin4 ==> Audio Power ==> RT Line Out Pin6 ==> RT Line Out ==> Reserved Pin8 ==> KEY ==> LFT Line Out Pin10 ==> LFT Line Out Front Panel Audio Connector/ Jumper Block 1 2 9 10 1 2 9 10 Pin 5 and 6 Pin 9 and 10 Audio line out signals are routed ==> to the back
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Back Panel Connectors JKBMS1 JPRNT1 PS/2 Mouse JGAME1 Parallel Game Port JUSB1 PS/2 Keyboard USB COM1 COM2 JCOM1 JCOM2 11 Speaker Line In Mic Out In
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Español Características del M7VIT Usa Chipsets VIA VT8377 (KT400) / VT8235, Winbond W83697HF. Contiene facilidades I/O integrados en la placa madre en el que incluye dos puertos en serie, un puerto paralelo, un puertos de ratón PS/2, un puerto de teclado PS/2, puertos de audio, puertos USB y un puerto de juego. Soporta Single Socket-A para procesadores de la familia AMD Athlon/ Duron, corriendo a 200/266/333 MHz frecuencia Front Side Bus.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Center a través de la utilidad del audio.) (Opcional). Soporta funciones del cabezal del Audio Frontal. CMI 8738 Características del Hardware Audio (Opcional): * 6CH DAC para AC3® 5.1CH purpose. * HRTF-based 3D audio posicional, soportando DirectSound™ 3D y A3D™ de interface. * Soporta altavoces de 4.1/5.1, C3DX audio posicional en 4/ 6 CH modo de altavoz. * Puerto MPU-401. * Integrado con puerto ZV.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Disposición del M7VIT 1 JKBV1 JUSBV1 Socket A 1 CPU VT8377 (KT400) JATXPWR1 GAME Port Entrada Entrada Salida del del MIC de Linea Altavoz 1 1 JGAME1 JAUDIO1 IDE1 IDE2 Winbond I/O 1 Ranua AGP BAT1 PCI1 Ranua PCI BIOS 1 1 PCI2 Ranura PCI 4 6 1 3 JUSB2 Codec PCI3 Ranura PCI 2 10 1 9 VT8235 JUSB3 2 PCI4 Hardware Audio JCMOS1 Ranura PCI 1 1 10 9 JUSBV2 PCI5 Ranura PCI Ranura CNR FDD1 JWOL1 1 JPANEL1 1 CNR1 2 1 JSFA
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Instalación de la CPU CP U 1. Tire de la palanca del lado del zócalo, luego levante la palanca hasta un ángulo de 90 grados. 2. Sitúe el contacto A del zócalo y busque el punto blanco o corte el borde en la CPU. Empareje el contacto A con el punto blanco/ corte del borde, luego inserte la CPU. 3. Presione la palanca para abajo. Ponga el ventilador en la CPU y abróchelo. Luego ponga el puerto de corriente del ventilador en el JCFAN1.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Módulos DDR DIMM: DIMM1-2-3 DRAM Tiempo de Acceso: 2.5V Unbuffered/ Registered DDR 1600/ 2100/ 2700/ 3200 Tipo requerido. DRAM Tipo: 64MB/ 128MB/ 256MB/ 512MB/ 1GB Módulo DIMM (184 contactos) Solamente soporta 4 bancos para DDR PC3200 (2pcs de DDR de Doble Cara o 3pcs DDR de una cara.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Cómo instalar un Módulo DIMM 1. El zócalo DIMM tiene una lengüeta plástica de seguridad y el módulo de memoria DIMM tiene una muesca asimétrica, así el módulo de memoria DIMM puede caber solamente en la ranura de una sóla dirección. 2. Tire la lengüeta hacia afuera. Inserte los módulos de memoria DIMM en el zócalo a los 90 grados, luego empuje hacia abajo verticalmente de modo que encaje en el lugar. 3.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Puentes, Cabezales, Conectores y Ranuras Conectores del Disco Duro: IDE1/ IDE2 La placa madre tiene un controlador de 32-bit PCI IDE que proporciona Modo PIO 0~4, Bus Master, y funcionalidad Ultra DMA / 33/ 66/ 100. Tiene dos conectores HDD IDE1 (primario) y IDE2 (secundario). El conector IDE puede conectar a un master y un drive esclavo, así puede conectar hasta cuatro discos rígidos. El primer disco duro debe estar siempre conectado al IDE1.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Conector de Corriente: JATXPWR1 JATXPWR1 (Conector de Corriente ATX) Cabezal Wake On LAN: WOL1 Tierra 5V_SB Wake up 1 JWOL1 Cabezal Frontal USB: JUSB2/3 2 1 JUSB2/3 Contacto1,2 Contacto3,4 Contacto5,6 Contacto7,8 Contacto9 Contacto10 ==> ==> ==> ==> ==> ==> +5V Dato(-) Dato(+) Tierra KEY NA 5V/ 5VSB Selección para USB/KB: JUSBV1/2/ JKBV1 1 JUSBV1/2 1 Contacto 1-2 on ==> 5V JKBV1 Contacto 2-3 on ==> 5V_SB 19
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Conector del Panel Frontal: JPANEL1 PWR_LED SLP (+) (+) (-) ON/OFF IR 24 2 23 1 SPK (+) (-) HLED RST IR SPK ==> Conector de Altavoz HLED ==> LED del Disco Duro RST ==> Boton de Reinicio IR ==> Conector Infrarojo SLP ==> Boton de Suspension PWR_LED ==> Corriente LED ON/ OFF ==> Boton de Encendido Selección del Reloj del CPU: JCLK1 4 6 1 3 JCLK1 Contacto 1-2, 5-6 ==> 100 Mhz Contacto 2-3, 5-6 ==> 133 Mhz (default) Contacto 2-3, 4-5 ==> 166Mhz C
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Subsistema de Audio: JAUDIO1/ JCDIN1 1 2 1 9 10 JAUDIO1 (Cabezal de Audio Frontal) 1 2 Contacto1 Contacto3 Contacto5 Contacto7 JAUDIO1 Contacto9 JCDIN1 (Cabezal de Entrada de Audio del CD-ROM) ==> Mic In ==> Mic Power ==> RT Line Out ==> Reserved ==> LFT Line Out Contacto2 ==> Tierra Contacto4 ==> Audio Power Contacto6 ==> RT Line Out Contacto8 ==> KEY Contacto10 ==> LFT Line Out Conector del Panel Frontal de Audio/ Jumper Block 1 2 9 10 1 2 9
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Puente de Borrar CMOS: JCMOS1 1 Contacto 1-2 on ==> Operacion Normal (default) Contacto 2-3 on ==> Borrar Datos CMOS JCMOS1 Conectores del Panel Trasero JKBMS1 JPRNT1 Raton PS/2 JGAME1 Paralelo Puerto de Juego JUSB1 Teclado PS/2 USB COM1 COM2 JCOM1 JCOM2 22 Salida del Altavoz Entrada Entrada de Linea del MIC
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn WarpSpeeder Introduction [ WarpSpeeder™ ], a new powerful control utility, features three user-friendly functions including Overclock Manager, Overvoltage Manager, and Hardware Monitor. The following three sections detail the installation of FastTrak 376 drivers on a system that has Windows 98/Me already installed.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn System Requirement OS Support: Windows 98 SE, Windows Me, Windows 2000, Windows XP DirectX: DirectX 8.1 or above. (The Windows XP operating system includes DirectX 8.1. If you use Windows XP, you do not need to install DirectX 8.1.) Installation 1. Execute the setup execution file, and then the following dialog will pop up. Please click “Next” button and follow the default procedure to install.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn 2. When you see the following dialog in setup procedure, it means setup is completed. If the “Launch the WarpSpeeder Tray Utility” checkbox is checked, the Tray Icon utility and [ WarpSpeeder™ ] utility will be automatically and immediately launched after you click “Finish” button.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Usage The following figures are just only for reference, the screen printed in this user manual will change according to your motherboard on hand. [ WarpSpeeder™ ] includes 1 tray icon and 5 panels: 1. Tray Icon: Whenever the Tray Icon utility is launched, it will display a little tray icon on the right side of Windows Taskbar. This utility is responsible for conveniently invoking [ WarpSpeeder™ ] Utility.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn 2. Main Panel If you click the tray icon, [ WarpSpeeder™ ] utility will be invoked. Please refer do the following figure; the utility’s first window you will see is Main Panel. Main Panel contains features as follows: a. Display the CPU Speed, CPU external clock, Memory clock, AGP clock, and PCI clock information. b. Contains About, Voltage, Overclock, and Hardware Monitor Buttons for invoking respective panels. c.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn 3. Voltage Panel Click the Voltage button in Main Panel, the button will be highlighted and the Voltage Panel will slide out to up as the following figure. In this panel, you can decide to increase CPU core voltage and Memory voltage or not. The default setting is “No”. If you want to get the best performance of overclocking, we recommend you click the option “Yes”.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn 4. Overclock Panel Click the Overclock button in Main Panel, the button will be highlighted and the Overclock Panel will slide out to left as the following figure. Overclock Panel contains the these features: a. “–3MHz button”, “-1MHz button”, “+1MHz button”, and “+3MHz button”: provide user the ability to do real-time overclock adjustment. Warning: Manually overclock is potentially dangerous, especially when the overclocking percentage is over 110 %.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn d. “Verify button”: User can click this button and [ WarpSpeeder™ ] will proceed a testing for current frequency. If the testing is ok, then the current frequency will be saved into system registry. If the testing fail, system will do a fail-safe rebooting. After reboot, the [ WarpSpeeder™ ] utility will restore to the hardware default setting or load the verified best and stable frequency according to the Recovery Dialog’s setting.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn 5. Hardware Monitor Panel Click the Hardware Monitor button in Main Panel, the button will be highlighted and the Hardware Monitor panel will slide out to left as the following figure. In this panel, you can get the real-time status information of your system. The information will be refreshed every 1 second. 6.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn 32
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Note: Because the overclock, overvoltage, and hardware monitor features are controlled by several separate chipset, [ WarpSpeeder™ ] divide these features to separate panels. If one chipset is not on board, the correlative button in Main panel will be disabled, but will not interfere other panels’ functions. This property can make [ WarpSpeeder™ ] utility more robust.
M Mootthheerrbbooaarrdd D Deessccrriippttiioonn Trouble Shooting PROBABLE SOLUTION No power to the system at all Power light don’t * Make sure power cable is securely plugged in illuminate, fan inside power supply does not turn * Replace cable on. Indicator light on keyboard does not turn on * Contact technical support PROBABLE SOLUTION System inoperative.
Solución de Problemas CAUSA PROBABLE SOLUCIÓN No hay corriente en el sistema. La luz de * Asegúrese que el cable de transmisión esté corriente no ilumina, ventilador dentro de la seguramente enchufado. fuente de alimentación apagada. Indicador de * Reemplace el cable. luz del teclado apagado. * Contacte ayuda técnica. CAUSA PROBABLE SOLUCIÓN Sistema inoperativo.
10/08/2002 36