V10.1.
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
Preface CE Marking This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place it on an unstable surface. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company. • The power adapter may have either a 2-prong or a 3-prong grounded plug.
Preface Polymer Battery Precautions Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf. • Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern. • Use proper handling procedures when using polymer batteries.
Preface General Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface Contents Notice .................................................................................I EuP-Standby and Off Mode Power Consumption Statement: .................................................................................II FCC Statement ................................................................ IV FCC RF Radiation Exposure Statement: ......................... V Instructions for Care and Operation ..............................VII Power Safety ....................................
Preface Multi-in-1 Card Reader ..................................................2-6 Audio Features ...............................................................2-7 Setup for Audio Recording ............................................2-8 Setup for 5.1 or 7.1 Surround Sound .............................2-9 Audio Notes for Model C Computers (Fn + 5) ...........2-11 TouchPad and Buttons/Mouse .....................................2-12 Gestures and Device Settings ......................................
Preface MEI Driver .....................................................................4-7 Audio .............................................................................4-7 Windows Experience Index ...........................................4-8 Optional Drivers ............................................................4-9 PC Camera ...................................................................4-10 Wireless LAN ..............................................................
Preface Upgrading the System Memory (RAM) ......................6-14 Replacing the Primary System Memory Modules .......6-15 Modules Overview ........................................................................7-1 Setting Up SATA RAID Mode ......................................7-2 AHCI Mode ...................................................................7-2 RAID ..............................................................................7-2 Intel® Rapid Storage Technology Application .............
Preface TV Tuner Module ........................................................7-85 Consumer Infrared Driver ............................................7-86 Digital TV Broadcast Signal ........................................7-87 TV Recording and Power Plans ...................................7-87 Remote Control Unit ....................................................7-87 THX TruStudio Pro Audio ..........................................7-88 THX TruStudio AP Installation .................................
Preface Specifications Processor ....................................................................... C-2 Processor ....................................................................... C-2 Core Logic .................................................................... C-2 Memory ......................................................................... C-2 Display .......................................................................... C-2 Video Adapter Options ......................................
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk, optical device, card reader), TouchPad & Mouse, Audio Features & Printer. • Chapter 3 The computer’s power management options.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “Drivers & Utilities” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the User’s Manual. You may also find the notes marked with a of interest to you. Notes Check the light colored boxes with the mark above to find detailed information about the computer’s features.
Quick Start Guide Not Included Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module.
1 Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 7 operating system is supported. Note: In order to run Windows 7 without limitations or decreased performance, your computer requires a minimum 1GB of system memory (RAM).
Quick Start Guide Model Differences This notebook series includes three different model types that mainly differ as indicated in the table below. Note that your model may appear slightly different from those pictured in this manual. Feature Model A Case Color Rubber Style Paint CPU Type Supported Core Logic Display Type Supported Video Cards Supported Power Supply Model B Model C Standard Paint See “Specifications” on page A - 1 for more details Intel® HM65 Chipset 15.6" (39.
1 Quick Start Guide System Startup 1. Remove all packing materials, and place the computer on a stable surface. 2. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. 3. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter. 4.
Quick Start Guide System Map: LCD Panel Open - Models A & B 1 Wireless Device Operation Aboard Aircraft 2 3 4 5 5 7 8 9 10 6 The use of any portable electronic transmission devices (e.g. WLAN or Bluetooth) aboard aircraft is usually prohibited. Make sure any wireless modules are OFF if you are using the computer aboard aircraft.
1 Quick Start Guide Figure 1 - 3 LCD Panel Open Built-In PC Camera LCD Speakers LED Indicators Power Button Keyboard Built-In Microphone TouchPad and Buttons 9. Fingerprint Reader (Optional) System Map: LCD Panel Open - Model C 1 1. 2. 3. 4. 5. 6. 7. 8. Wireless Device Operation Aboard Aircraft 2 3 3 4 6 7 Note that the Touchpad and Buttons valid operational area is that indicated within the red dotted lines above. The use of any portable electronic transmission devices (e.g.
Quick Start Guide LED Indicators The LED indicators display helpful information about the current status of the computer.
1 Quick Start Guide Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot-keys unique to the system’s regular keyboard may not work. Keyboard The keyboard has an embedded numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly.
Quick Start Guide Function Keys & Visual Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators (see the table below) are available when the Hot Key driver is installed. After installing the driver an icon will appear in the taskbar.
1 Quick Start Guide Figure 1 - 5 Front View 1. LED Power Indicators 2. Vent/Fan Intake 3. eSATA/USB 2.0 Combo Port 4. HDMI-Out Port 5. DVI-Out Port 6. DC-In Jack 7. Security Lock Slot (Model C Only) 8.
Quick Start Guide System Map: Right View Figure 1 - 7 6 Right View Models A & B 1 2 3 4 5 7 6 Model C 2 1 3 4 5 6 1. Optical Device Drive Bay 2. Headphone Jack 3. Microphone Jack 4. S/PDIF-Out Jack 5. Line-In Jack 6. 1 * USB 2.0 Port 7. Security Lock Slot (Models A & B Only) USB 2.0 or 3.0 Ports USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black.
1 Quick Start Guide Figure 1 - 8 Left View RJ-45 LAN Jack 2 * USB 3.0 Ports 1 * USB 2.0 Port Mini-IEEE 1394a Port 5. Multi-in-1 Card Reader 6. CATV Antenna Jack (Model C Only for TV Tuner Option) System Map: Left View Models A & B 1. 2. 3. 4. 1 2 2 5 4 3 Model C 6 1 2 2 3 4 5 USB 3.0 Ports & USB Port Power Mini-IEEE 1394a Port The Mini-IEEE 1394a port only supports SELF POWERED IEEE 1394 devices. USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black.
Quick Start Guide System Map: Bottom View - Models A & B 3 2 2 2 1 Figure 1 - 9 Bottom View 1. Sub Woofer 2. Fan Outlet/Intake 3. Component Bay Cover 4. HDD Bay 5. Battery 2 4 5 Overheating Battery Information Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 10 for full instructions.
1 Quick Start Guide Figure 1 - 10 Bottom View 1. Sub Woofer 2. Fan Outlet/Intake 3. Component Bay Cover 4. Primary HDD Bay 5. Secondary HDD Bay 6. Battery 7. Speakers System Map: Bottom View - Model C 1 2 2 2 3 2 4 6 5 Overheating To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s) while the computer is in use. 7 6 7 7 Battery Information Always completely discharge, then fully charge, a new battery before using it.
Quick Start Guide Windows 7 Start Menu & Control Panel Most of the control panels, utilities and programs within Windows 7 (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
1 Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display control panel (in Appearances and Personalization) in Windows 7. To access Display (Control Panel) and Screen Resolution in Windows: 1. 2. 3. Click Start and click Control Panel. Click Display (icon) - In the Appearances and Personalization category. Click Adjust Screen Resolution/Adjust resolution. OR 4. 5.
Quick Start Guide Screen Resolution Video Options Note that card types, specifications and drivers are subject to continual updates and changes. Check with your service center for the latest details on video cards supported.
1 Quick Start Guide NVIDIA Control Panel You can access the NVIDIA Control Panel as follows: 1. 2. 3. Click Start, and click Control Panel. Click NVIDIA Control Panel 1 (Figure 1 - 13) - In the Appearances and Personalization category. See “NVIDIA Video Driver Controls” on page B - 1 for full details on control panels etc. OR 4. You can also access the control panel by right-clicking the desktop and selecting NVIDIA Control Panel 2 .
Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 16) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
1 Quick Start Guide 1 - 22
Storage Devices, Mouse, Audio & Printer Chapter 2: Storage Devices, Mouse, Audio & Printer Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • Hard Disk Drive Optical Device Multi-in-1 Card Reader Audio Features TouchPad and Buttons/Mouse Adding a Printer Overview 2 - 1 2
Storage Devices, Mouse, Audio & Printer 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Hard Disk Drive The hard disk drive(s) is used to store your data in the computer. The hard disks) can be taken out to accommodate other 2.
Storage Devices, Mouse, Audio & Printer Optical Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the model you purchased (see “Storage” on page C - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 13).
Storage Devices, Mouse, Audio & Printer 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Disk Eject Warning Don’t try to remove a CD/DVD while the system is accessing it. This may cause the system to “crash”.
Storage Devices, Mouse, Audio & Printer DVD Regional Codes To change the DVD regional codes: 1. 2. 3. Go to the Control Panel Double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code.
Storage Devices, Mouse, Audio & Printer 2 Card Reader Cover Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. Figure 2 - 4 Multi-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Storage Devices, Mouse, Audio & Printer Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/ control panel (right-click the taskbar icon to bring up an audio menu). The volume may also be adjusted by means of the Fn + F5/F6 key combination (see Table 1 - 4, on page 1 - 11).
Storage Devices, Mouse, Audio & Printer Setup for Audio Recording 2 To record audio sources on your computer at optimum quality follow the instructions below: 1. 2. 3. 4. Figure 2 - 6 Realtek Audio Manager Recording Setup 2 - 8 Audio Features Click Start, and click Control Panel (or point to Settings and click Control Panel) and make sure you are in Classic View. Click Realtek HD Audio Manager (or right-click the taskbar icon and select Sound Manager).
Storage Devices, Mouse, Audio & Printer Setup for 5.1 or 7.1 Surround Sound To setup your system for 5.1 or 7.1 surround sound you will need to connect the audio cables to the Headphone-Out, Line-In, Microphone-In jack and S/PDIF-Out jacks (note: the S/PDIF jack is used for 7.1 surround sound only). 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel) and make sure you are in Classic View.
Storage Devices, Mouse, Audio & Printer 5. 6. 2 Plug the front speaker cables into the Headphone-Out Jack. Plug in the other cables (you may require an adapter to connect each cable to the appropriate jack e.g a stereo mini to dual RCA adapter) from your speakers as follows: • Line-In Jack = Rear Speaker Out • Microphone-In Jack = Center/Subwoofer Speaker Out • S/PDIF-Out Jack = Side Speaker Out (for 7.1 Surround Sound Only) 7. 8. 9.
Storage Devices, Mouse, Audio & Printer Audio Notes for Model C Computers (Fn + 5) Model C computers (Model C only) feature the Fn +5 key combination to toggle between standard audio and enhanced audio. Note the following which applies to software mode audio configuration through the computer’s internal speakers only (this does not apply to surround sound when configured through external Quadrophonic, 5.1 or 7.
Storage Devices, Mouse, Audio & Printer 2 Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details. TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.
Storage Devices, Mouse, Audio & Printer Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 7) you can configure the functions from the Mouse control panel in Windows, or by doubleclicking the TouchPad driver icon on the taskbar. You may then configure the TouchPad tapping, buttons, scrolling, pointer motion and sensitivity options to your preferences. You will find further information at www.synaptics.com.
Storage Devices, Mouse, Audio & Printer 2 Show Video You can get a clearer view of the gestures involved by clicking the Show Video option for each gesture item. Select the gesture (Pinch Zoom, Rotating, Three Fingers Down and Three Finger Flick) in the Device Settings > Settings left tree menu and click the Show Video button to see the demonstration video.
Storage Devices, Mouse, Audio & Printer Scrolling The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the TouchPad surface and slide both fingers in the direction required (in a straight continuous motion).
Storage Devices, Mouse, Audio & Printer Rotating Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the TouchPad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.
Storage Devices, Mouse, Audio & Printer Adding a Printer The most commonly used peripheral is a printer. The following conventions will help you to add a printer; however it is always best to refer to the printer manual for specific instructions and configuration options. USB Printer Most new printers have a USB interface connection. You may use any one of the ports to connect the printer. Install Instructions: 1. 2. 3. 4. 5.
Storage Devices, Mouse, Audio & Printer 2 2 - 18
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. 3 AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components (see page C - 5). 1. 2. 3. 4. Attach the AC/DC adapter to the DC-In jack at the rear of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle.
Power Management Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.
Power Management 3 Resuming Operation See Table 3 - 1, on page 3 - 9 for information on how to resume from a power-saving state. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 1 Power Plan Advanced Settings (Win 7) 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source.
Power Management Power-Saving States 3 You can use power-saving states to stop the computer’s operation and restart where you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states. Sleep In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management 3 Password Protection Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu. It is recommended that you enable a password on wake up in order to protect your data.
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo). Power Status Icon Color Power Off Off Sleep Blinking Green To Resume Press the Power Button Press the Power Button Closing the Lid If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up.
Power Management 3 Low Battery Warning When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted. Battery Information Follow these simple guidelines to get the best use out of your battery. Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g.
Power Management Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter. • Reduce the amount of time before the display is turned off. • Close wireless, Bluetooth, modem or communication applications when they are not being used.
Power Management Battery Life 3 Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see “Removing the Battery” on page 6 - 3.
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances. • DO NOT expose the battery to fire or high temperatures, it may explode. • DO NOT connect the metal terminals (+, -) to each other. Caution Danger of explosion if battery is incorrectly replaced. Damaged Battery Warning Should you notice any physical defects (e.g.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 3 1. 2. Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 3. Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options.
Power Management How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Power Management 3 3 - 18
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Drivers (button) to access the Optional driver menu. 4 1. 2. 3. Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below. Click to select the driver you wish to install, (you should note down the drivers as you install them).
Drivers & Utilities Windows 7 Driver Page Windows 7 Driver Page Chipset Page 4 - 6 PC Camera Module Page 7 - 15 Video (VGA) Page 4 - 6 Wireless LAN Module Page 7 - 23 LAN Page 4 - 6 Fingerprint Reader Module Page 7 - 42 Card Reader Page 4 - 7 Bluetooth Module Page 7 - 49 TouchPad Page 4 - 7 3.75G/HSPA Module (Models A & B Only) Page 7 - 66 USB 3.
Drivers & Utilities 4 Manual Driver Installation Updating/Reinstalling Individual Drivers Click the Browse CD/DVD button in the Drivers Installer application and browse to the executable file in the appropriate driver folder. If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Programs > Uninstall a program).
Drivers & Utilities User Account Control New Hardware Found If a User Account Control prompt appears as part of the driver installation procedure, click Continue/Allow, and follow the installation procedure as directed. If you see the message “New Hardware Found” during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure.
Drivers & Utilities Driver Installation Procedure Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Drivers (button) to access the Optional driver menu. 4 Driver Installation General Guidelines The driver installation procedure outlined in this Chapter (and in Chapter 7 Options & Modules), are accurate at the time of going to press. Drivers are always subject to upgrade and revision so the exact procedure for certain drivers may differ slightly.
Drivers & Utilities Card Reader 1. Click 4.Install Cardreader Driver > Yes. 2. Click Install. 3. Click Finish to complete the installation. TouchPad 1. Click 5.Install Touchpad Driver > Yes. 2. Click Next. 3. Click the button to accept the license, and then click Next. 4. Click Finish > Restart Now to restart the computer. Hot Key 1. Click 6.Install Hotkey AP > Yes. 2. Click Next > Next. 3. Click Finish > Finish to restart your computer. USB 3.0 1. Click 7.Install USB 3.0 Driver > Yes. 2. Click Next. 3.
Drivers & Utilities It is recommended that you install the THX Tru Studio Pro Audio application (see “THX TruStudio AP Installation” on page 7 - 88) and Intel Rapid Storage Technology driver (see “IRST Driver Installation” on page 7 - 8 - required for AHCI & RAID mode). 4 Windows Experience Index After Video (VGA) driver has been installed, and the system restarted, the OS will automatically run the "Winsat.exe" to rate the performance.
Drivers & Utilities Optional Drivers See the pages indicated for the driver installation procedures for any modules included in your purchase option. 4 Models A & B Model C Figure 4 - 3 - Optional Drivers Installer Screen Note that for Intel and 3rd party WLAN & Bluetooth Combo modules you need to install both the WLAN & Bluetooth drivers.
Drivers & Utilities PC Camera See the install procedure in “PC Camera Module” on page 7 - 14. 4 Wireless LAN See the appropriate install procedure for your WLAN module in “Wireless LAN Module” on page 7 - 22. Fingerprint Reader Module See the install procedure in “Fingerprint Reader Module” on page 7 - 42. Bluetooth & WLAN Combo Module See “3rd Party Bluetooth Combo Driver Installation” on page 7 - 49 or “Intel Bluetooth Combo Driver Installation” on page 7 - 57. 3.
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make.
BIOS Utilities The Power-On Self Test (POST) If you enable the Boot-time Diagnostic Screen in the Setup Utility, each time you turn on the computer the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory). 5 As the POST proceeds, the computer will tell you if there is anything wrong. If there is a problem that prevents the system from booting, it will display a system summary and prompt you to run Setup.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities BIOS Settings Warning 5 Incorrect settings can cause your system to malfunction. To correct mistakes, return to Setup and restore the Previous Values with , or Optimized Defaults with . The Setup Utility The Aptio Setup Utility tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration).
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box at the bottom right side of the screen. Setup Menus The Setup menus shown in this section are for reference only.
BIOS Utilities Main Menu Figure 5 - 2 Main Menu 5 System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
BIOS Utilities SATA Port # (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Ports. System/Extended Memory: (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed. 5 MB Series / BIOS Revision / KBC/EC firmware Revision / VGA Card etc. (Main Menu) This item contains information on the BIOS version and video card etc.
BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu 5 Advanced Chipset Control (Advanced Menu) The sub-menu here allows you to adjust the Bluetooth Power Setting.
BIOS Utilities Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control) You can adjust the Bluetooth module power setting to your preference. The default setting (Disabled) will see the Bluetooth module powered off when the system is started up or restarted. Enabling the power setting will have the module retain the last power status (on or off) before any restart or shut down.
BIOS Utilities Boot Logo: (Advanced Menu) Use this menu item to enable/disable the Boot Logo screen at system startup. Power On Boot Beep (Advanced Menu) Use this menu item to enable/disable the beep as the computer starts up. 5 Battery Low Alarm Beep: (Advanced Menu) Use this menu item to enable/disable the battery low alarm beep.
BIOS Utilities Security Menu Security Menu The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS. Figure 5 - 4 Security Menu Set Supervisor Password (Security Menu) You can set a password for access to the Aptio Setup Utility. This will not affect access to the computer OS (only the Aptio Setup Utility).
BIOS Utilities Password Warning 5 If you set a boot password (Password on boot is “Enabled“), NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
BIOS Utilities Boot Menu Figure 5 - 5 Boot Menu BIOS Screens Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s BIOS. When you turn the computer on it will look for an operating system (e.g. Windows 7) from the devices listed in this menu, and in this priority order. If it cannot find the operating system on that device, it will try to load it from the next device in the order specified in the Boot Sequence.
BIOS Utilities Boot Sequence (Boot Menu) Use the arrow keys to move up and down the menu and use the F5 and F6 keys to move the device’s boot priority up and down the list (the selected device will be highlighted in white).
BIOS Utilities Exit Menu Figure 5 - 6 Exit Menu 5 Click Save Changes and Reset to save all changes made. Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Setup defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session.
BIOS Utilities 5 5 - 16
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. Before removing the battery disconnect the AC/DC adapter from the computer first.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. Before removing the battery disconnect the AC/ DC adapter from the computer first. Note that only Model A/B is pictured, however the procedure for removing the battery from Model C is the same. 1. 2. 3. 4. 5. Turn the computer off, remove the AC/DC adapter and turn it over. Slide the latch 1 in the direction of the arrow.
Upgrading The Computer Upgrading the Optical Device (Model A/B) 1. 2. 3. 4. Locate the hard disk bay cover and remove screws 1 & 2 . Remove the hard disk bay cover 3 . Remove the screw at point 4 , and use a screwdriver to carefully push out the optical device at point 5 . Reverse the process to install any new optical (CD/DVD) device.
Upgrading The Computer Upgrading the Optical Device (Model C) 1. 2. 3. 4. Locate the secondary hard disk bay cover and remove screws 1 & 2 . Remove the hard disk bay cover 3 . Remove the screw at point 3 , and use a screwdriver to carefully push out the optical device out of the bay. Reverse the process to install any new optical (CD/DVD) device.
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CD-ROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer Removing the Hard Disk from the Primary HDD Bay Note that only Model A/B is pictured, however the procedure for removing the primary hard disk from Model C is the same (note the screw location differences). 1. 2. 3. Turn the computer off, remove the AC/DC adapter, turn it over and remove the battery. Locate the hard disk bay cover and remove screws 1 & 2 (screw 2 is located in a different position depending on your model).
Upgrading The Computer 4. 5. Slide the HDD assembly in the direction of arrow 4 Remove the hard disk assembly 5 . .
Upgrading The Computer 6. 7. Remove screws 6 & 7 and the insulation plate 8 . Reverse the process to install a new disk and do not forget to install the insulation plate.
Upgrading The Computer Inserting the Hard Disk Into the Primary HDD Bay 1. 2. 3. 6 Make sure the HDD assembly is aligned with the black taped area 1 . When aligned, carefully insert the HDD assembly 2 into the case so that the connectors line up. Replace the hard disk bay covers and screws.
Upgrading The Computer Removing the Hard Disk from the Secondary HDD Bay (Model C Only) Note that the secondary hard disk (if installed) is located under the optical device bay (CD/DVD). 1. 2. 3. 4. Turn the computer off, remove the AC/DC adapter, turn it over and remove the battery. Remove the optical device (see “Upgrading the Optical Device (Model C)” on page 6 - 5) When the optical device is removed the secondary HDD assembly will be visible. Remove screws 1 - 3 from the secondary HDD assembly.
Upgrading The Computer 5. 6. Slide the secondary HDD assembly in the direction of the arrow 4 (it will not move fully out of the bay), Lift the secondary HDD assembly 5 up out of the bay (in the reverse direction to arrow 4 ).
Upgrading The Computer 7. Remove screws 6 - 9 and the insulation plate 10 . 9 8 Figure 6 - 10 10 Secondary Hard Disk Insulation Plate Removal 6 7 6 8. 9. 10. 11. Reverse the process to install a new disk (make sure you install the insulation plate). Slide the HDD assembly into the bay at an angle as illustrated. Make sure the insulation plate slides under the HDD bay guide at point 11 .
Upgrading The Computer Upgrading the System Memory (RAM) The computer has four memory sockets for 204 pin Small Outline Dual In-line (SODIMM) DDR III (DDR3) type memory modules (see “Memory” on page C - 2). The total memory size is automatically detected by the POST routine once you turn on your computer. 6 Note that four SO-DIMMs are only supported by Quad-Core CPUs; Dual-Core CPUs support two SO-DIMMs maximum (see “Memory” on page C - 2 for full details).
Upgrading The Computer Replacing the Primary System Memory Modules 1. 2. Turn off the computer, and turn it over and remove the battery. Remove screws 1 - 4 from the bottom of the computer . 1 2 2 4 3 4 1 3 5 Models A & B 3. Figure 6 - 12 Bottom Cover Screws 6 Model C Slide the bottom cover until the cover and case indicators 5 are aligned.
Upgrading The Computer 4. Lift the bottom cover 6 off the computer case. Figure 6 - 14 Bottom Cover Removal 6 Contact Warning 6 Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance. 5. Gently pull the two release latches ( 7 & 8 ) on the sides of the memory sockets) in the direction indicated below. 7 8 9 Figure 6 - 15 RAM Module Removal 6.
Upgrading The Computer 7. 8. Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory socket. 9. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the socket as it will go. DO NOT FORCE the module; it should fit without much pressure. 10. Press the module in and down towards the mainboard until the socket levers click into place to secure the module.
Upgrading The Computer 6 6 - 18
Modules Chapter 7: Modules Overview This chapter contains the information on the various modules (some of which are optional) which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. The chapter includes information on the following: • • • • • • • • Setting Up SATA RAID Mode PC Camera Module Wireless LAN Module Fingerprint Reader Module Bluetooth Module 3.
Modules RAID Hard Disks All hard disks in a RAID should be identical (the same size and brand) in order to prevent unexpected system behavior. SATA Mode Selection 7 The SATA mode selection should be made before installing your operating system. DO NOT change your selected SATA mode unless you intend to reinstall your operating system. Make sure you have backed up all your data before doing so.
Modules RAID Level Description Table 7 - 1 RAID 0 Identical drives reading and writing data in parallel to increase performance. RAID 0 implements a striped disk array and the data is broken into blocks and each block is written to a separate disk drive. RAID Levels RAID 1 Identical drives in a mirrored configuration used to protect data. Should a drive that is part of a mirrored array fail, the mirrored drive (which contains identical data) will handle all the data.
Modules SATA RAID Setup Procedure (BIOS) 1. 2. Start-up your notebook computer and press to enter the BIOS. Go to the Advanced menu, select "SATA Mode" and press Enter (see page 5 - 8). • Select “RAID Mode”. 3. 4. 5. 7 6. Press Esc and go to the Boot menu. Set the DVD-ROM Drive (make sure the Microsoft Windows 7 OS DVD is inserted) as the first device in the boot order from the Boot menu (see “Boot Menu” on page 5 - 15).
Modules RAID Setup (Intel Matrix) 1. As the computer starts up press Ctrl + i to enter RAID configuration menu. Figure 7 - 1 Intel(R) Rapid Storage Technology Option ROM Recovery Level When selecting disks for the Recovery RAID level you will need to use the Tab key to select a Master disk, and the Space key to select a Recovery disk. 2. 3. 4. Select 1.Create RAID Volume and press Enter. Type the RAID volume name and then press Tab or Enter to advance to the next field.
Modules Recovery Level When selecting disks for the Recovery RAID level you will need to use the Tab key to select a Master disk, and the Space key to select a Recovery disk. 7 5. 6. 7. 8. 9. 10. Press Enter and the system will select the physical disks to use. Press Enter and select (if applicable) the Strip Size (best set to default). Press Enter and select the Capacity size (best set to default). Press Enter to select Create Volume.
Modules 12. Make sure the Windows 7 OS DVD is in the DVD drive. and as the computer starts up it will automatically boot from the Windows 7 OS DVD (you will be prompted to press a key to boot from the DVD). 13. Press Enter to continue installing the operating system as normal (see your Windows documentation if you need help on installing the Windows OS - see sidebar). 14.
Modules Intel Rapid Storage Technology The Intel Rapid Storage Technology application provides high-performance SATA and SATA RAID capabilities. Install the Intel Rapid Storage Technology application to support your RAID system or SATA drive if set up in AHCI mode in the BIOS (see “SATA Mode (Advanced Menu)” on page 5 - 9). 7 IRST Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers (button). 3. Click 7.
Modules Intel® Rapid Storage Technology for RAID Systems Intel® Rapid Storage Technology application displays status information on your RAID configuration. Run the Intel® Rapid Storage Technology application from the Intel item in the All Programs menu. When the Intel® Rapid Storage Technology application is launched the system will open the Status window. Here you can view the general health of the storage system.
Modules Help Click the Help (or press F1) menu button at the top of the Intel® Rapid Storage Technology application. 7 Intel® Rapid Storage Technology Help If a hard drive member of a RAID volume is reported as “Degraded” or “Failed” it may be possible to recover the volume. If the volume cannot be restored then you will need to recreate the RAID volume and restore the data from a back up. Click the Help menu (or press F1) for instructions on how to recover or recreate RAID Volumes.
Modules RAID Volume Data Verification and Repair The RAID volume data verification process identifies any inconsistencies or bad data on a RAID 0 or RAID 1 volume. The table outlines what occurs for each RAID level: RAID Level Verify RAID 0 Bad blocks are identified. Verify & Repair Table 7 - 2 N/A Bad blocks are reassigned. Bad blocks are identified. RAID 1 Data on the mirrored drive is compared to data on the source drive.
Modules Verifying and Repairing RAID Volume Data 1. 2. 3. 4. 5. Before verifying the volume data you will need to initialize the volume. Run the Intel® Rapid Storage Technology application from the Intel item in the Programs/All Programs menu. Click Manage and click Advanced. Click Initialize and click Yes (button) to begin the process. The completion percentage will be listed under Status.
Modules 6. 7. Click Advanced and click Verify, then click Verify (button) to begin the process. The completion percentage will be listed under Status (verifying and repairing).
Modules Latest PC Camera Driver Information Check the Device Drivers & Utilities + User’s Manual disc and any accompanying insert pages, for the latest updated information on the PC Camera driver, which may override the information provided here. 7 PC Camera Module Before installing the driver, make sure the PC Camera is on. Use the Fn + F10 key combination to toggle power to the to the PC Camera module. When the PC Camera module is powered on the indicator will briefly be displayed.
Modules PC Camera Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install Webcam Driver > Yes. 4. Click Next > Install > Finish to restart the computer. OR Choose the language you prefer and click Next > Next > Finish. OR Click Next > Finish to restart the computer. 5.
Modules PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. 7 Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Recording (tab). Right-click Microphone (Realtek High Definition Audio) and make sure the item is not disabled. 5. Double-click Microphone (or select Properties from the right-click menu). 6.
Modules Figure 7 - 7 Audio Setup for PC Camera Right-click 7 PC Camera Module 7 - 17
Modules Camera Application The camera application is a video viewer for general purpose video viewing and testing, and for capturing video files to .avi format. 1. 2. 3. 7 Run the camera application from the desktop shortcut (it is recommended that you set the capture file before the capture process - see below). Go to the Capture menu heading (if you wish to capture audio check “PC Camera Audio Setup” on page 7 - 16) and select Start Capture.
Modules Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Modules Latest PC Camera Driver Information 7 Check the Device Drivers & Utilities + User’s Manual disc, and any accompanying insert pages, for the latest updated information on the PC Camera driver, which may override the information provided here, including the figures pictured here. Eliminating Screen Flicker If you find that the video screen in the camera program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3.
Modules Taking Still Pictures The camera application allows you to take still pictures. 1. 2. 3. Run the camera application from the desktop shortcut. Go to Options and select Take Picture. The picture (in JPEG format) will be placed in the Snapshot folder desktop. Snapshot Folder on the The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture.
Modules Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Wireless LAN Module If you have included an Intel® or 3rd Party 802.11b/g/n WLAN module in your purchase option, make sure that the Wireless LAN module is on before installing the driver. Use the Fn + F11 key combination to toggle power to the Wireless LAN module.
Modules Intel® Wi-Fi Link Series Driver Installation If you see the message “Found New Hardware” click Cancel to close the window. 1. Make sure the module is powered on, then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 2.Install WLAN Driver > Yes. 4. Click Next > Next. 5. Click the button to accept the license and click Next. 6. Click Next > Next > Finish.
Modules Network and Sharing Center You can also use the Network and Sharing Center control panel in Windows (Network and Internet) to connect to any available wireless networks. Connecting to a Wireless Network in Windows 7 Make sure the Wireless LAN module is turned on. 1.
Modules 2. 3. 4. You may need to enter a security key for any access point to which you are trying to connect. Click to select a network location (e.g. Home, Work or Public). Click “View or change settings in Network and Sharing Center” to access further options for the connection.
Modules Security Enabled Networks 5. 6. Click the taskbar icon to see any currently connected networks. To disconnect from the wireless network you can click the taskbar wireless icon click the active connection and then click Disconnect (button). You should try to make sure that any network you are connecting to is a secure network. 7 Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Modules Intel® My WiFi Configuration Intel® My WiFi Technology uses your WLAN (for Intel WLAN modules only) module to allow you to connect up to eight other WiFi enabled devices (e.g. digital cameras, other computers, cell phones, handheld devices etc.) to your computer (similar to Bluetooth), while still connecting to the Internet through your WiFi wireless connection. Intel® My WiFi Technology offers greater range and speed than other personal area networks, and does not require an access point.
Modules Intel® My WiFi Configuration You can configure the My WiFi settings as follows. 1. 2. 7 Access the Intel® My WiFi Utility from the Start menu (Start > Programs/All Programs > Intel PROSet Wireless > Intel My WiFi Technology), or by doubleclicking the taskbar icon . Click Enable (on the first run of the program there will be no connected devices listed).
Modules 3. 4. 5. Click Start and click Control Panel. Click Network and Sharing Center (Network and Internet). Click Change adapter settings.
Modules 6. Right-click Wireless Network Connection and select Properties. Figure 7 - 14 Network Connections Right-click Wireless Network Connection and select Properties.
Modules 7. 8. 9. Click Sharing (tab) and select “Allow other network users to connect through this computer’s Internet connection”. Select Wireless Network Connection under Home networking connection. Click OK. Click “Allow other network users to connect through this computer’s Internet connection”. Select Wireless Network Connection.
Modules 10. Access the Intel® My WiFi Utility from the Start menu (Start > Programs/All Programs > Intel PROSet Wireless > Intel My WiFi Technology), or by doubleclicking the taskbar icon . 11. Click Profiles .
Modules 12. Click Profiles, click Intel Wireless PAN and click Edit or New (Note that all preset settings may not be editable - see sidebar). Figure 7 - 17 Profiles Profile Settings 13. You can change the Profile Name and Network Name to your personal preferences in General (tab). Profile and Network Names The Profile Name is the name as displayed on your computer in the Network Connections control panel (see Figure 7 - 19 on page 7 - 34).
Modules 14. Click Security (tab). 15. Change the Security Type to WEP and the Encryption Type to 64bit. 16. Enter a password (8 characters long) in the Password box.
Modules 17. Click Sharing (tab). 18. It is recommended that the Filter Network Traffic and DHCP and DNS Server are Disabled.
Modules 19. Click Advanced (tab). 20. It is recommended that the Default Channel is set to Channel 1, 6 or 11. 21. Click OK to save the settings.
Modules 22. Double-click Wireless Network Connection in Network Connections. 23. Click Details to display the Network Connection Details.
Modules 24. Access the Intel® My WiFi Utility from the Start menu (Start > Programs/All Programs > Intel PROSet Wireless > Intel My WiFi Technology), or by clicking the taskbar icon . 25. To add a new device follow the instructions in the devices’ user guide for connecting to a WiFi network. 26. Click Add New Device in Intel® My WiFi Utility to confirm the security settings detail.
Modules Intel WLAN & Bluetooth Combo Module High-Speed Data Transfer Configuration You will need to configure the following settings to enable high-speed wireless data transfer as supported by Intel Wireless LAN & Bluetooth Combo modules (note this information applies to Intel WLAN & Bluetooth Combo modules only). 1. Go the Windows control panel and double-click Device Manager (in Hardware and Sound under Devices and Printers).
Modules 2. 3. 4. 5. 6. 7. 8. Click Network adapters to expand the sub-menu. Double-click the Intel WiFi Link .... module. Click Advanced (tab). Click 802.11n Channel Width for band 2.4 under “Property:”. Click the pull-down menu under “Value:” Click to select Auto. Click OK and close the control panels.
Modules Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center: 1. 2. 3. Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Windows Mobility Center (Mobile PC). Click the button to Turn wireless off/on, or click the icon to access the network menu.
Modules Password Warning If you set passwords for any of the security modules, NEVER forget your password. 7 The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. Fingerprint Reader Module The fingerprint reader Protector Suite Software provides a high level of security for your computer.
Modules Fingerprint Reader Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers. 3. Click 3.Install FingerPrint Driver > Yes. 4. Click Next > Next > Next. 5. Click Finish > Yes to restart the computer. 6. Click the tray icon , scan a finger or click Start > Programs/All Programs > Protector Suite > Control Center and then begin the enrollment process (see over).
Modules User Enrollment 1. Fingerprint Enrollment 2. Note that it is strongly recommended that you enroll more than one finger in case of injury etc. 3. 4. 5. Click Start > Programs/All Programs > Protector Suite > Control Center, or double click the taskbar icon (click Initialize). On the first run of the program you will be asked to click the Accept button to accept the license.
Modules 6. 7. Click the button above any of the fingers to begin the enrollment process for that finger. Swipe the finger until the progress bar reaches 100% to enroll that finger. Fingerprint Enrollment Note that it is strongly recommended that you enroll more than one finger in case of injury etc. 7 Figure 7 - 28 Fingerprint Enrollment Progress 8. Close the Protector Suite 2009 window.
Modules 9. Right-click the taskbar icon and select Start Control Center (and then swipe a finger) to allow you to Edit Fingerprints, register Applications, edit Settings and access the Help menu etc. You can also run the Control Center etc. from the Protector Suite item in the Programs/All Programs menu 10. Click “Help” to get more information on any topic. 11. You can also run the Tutorial, or Product Tour video to get more information. Figure 7 - 29 Control Center & Biomenu Help 7 12.
Modules Fingerprint Control Center Features Application Launcher The Application Launcher allows you to register applications to be launched when assigned to a particular finger. Simply copy the application icon on to one of the registered fingers and ten click OK to close the application window. Once registered the application will launch when you swipe the appropriate finger across the sensor.
Modules Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + F12 key combination to toggle power to the Bluetooth module, and check the LED indicator to see if the module is powered on or not (see Table 1 - 4, on page 1 - 11/Table 1 - 2, on page 1 - 9).
Modules 3rd Party Bluetooth Combo Driver Installation Note this driver is required only for the combo Bluetooth and WLAN module only. 1. Before installing the driver make sure the Bluetooth module is powered on (use Fn + F12 key combination), then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. If a Found New Hardware window appears, click Cancel in all windows that appear, and then proceed to install the driver as below. 2. Click Option Drivers (button). 3. Click 4.
Modules Bluetooth Module & Resuming From Sleep Mode The Bluetooth module’s default state will be off after resuming from the Sleep power-saving state. Use the key combination (Fn + F12) to power on the Bluetooth module after the computer resumes from Sleep. 3rd Party Bluetooth & WLAN Combo Settings This information applies to the combo Bluetooth and WLAN module only. 1. 2. 3. 7 Figure 7 - 30 My Bluetooth Settings 7 - 50 Bluetooth Module Make sure the Bluetooth module is powered on.
Modules 4. 5. Click General Settings to change the computer name that other Bluetooth devices will see, and click the tickbox to Allow Bluetooth devices to find this computer Click OK to confirm the settings.
Modules 6. 7. 7 Figure 7 - 32 File Transfer Settings 7 - 52 Bluetooth Module Click File Transfer Settings to Enable sharing of my files with other Bluetooth devices. Click OK to confirm the settings.
Modules 3rd Party Bluetooth Networking Setup This information applies to the combo Bluetooth and WLAN module only. 1. 2. 3. Make sure the Bluetooth module is powered on. Double-click the My Bluetooth application on the desktop (or access it from the Programs/All Programs menu). Click My Bluetooth Settings (see Figure 7 - 30 on page 7 - 50). 7 Figure 7 - 33 Network Settings 4. 5. 6. Click Network Settings (make sure the Bluetooth module is powered on. Click Enable Bluetooth Network and click OK.
Modules Bluetooth Module & Resuming From Sleep Mode The Bluetooth module’s default state will be off after resuming from the Sleep power-saving state. Use the key combination (Fn + F12) to power on the Bluetooth module after the computer resumes from Sleep. 3rd Party Bluetooth & WLAN Combo Module Configuration Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on.
Modules 3. You will then be presented with a menu of options to select from. 7 Figure 7 - 35 Bluetooth Device Options 4. Click the appropriate button to connect to the device.
Modules 5. 6. 7 Figure 7 - 36 Bluetooth Pairing Code & Connection Established 7 - 56 Bluetooth Module You may need to allow the connection from your device, and you will then need to provide a passcode from the device. You can then enter the passcode on the computer and click OK to establish the connection.
Modules Intel Bluetooth Combo Driver Installation Note this driver is required only for the Intel combo Bluetooth and WLAN module only. 1. Before installing the driver make sure the Bluetooth module is powered on (use Fn + F12 key combination), then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. If a Found New Hardware window appears, click Cancel in all windows that appear, and then proceed to install the driver as below. 2. Click Option Drivers (button). 3. Click 4.
Modules Standard Bluetooth Configuration in Windows 7 Add a Device Click Start, and click Control Panel and then click Devices and Printers (Hardware and Sound). Click Add a device to search for any available Bluetooth devices. 7 Bluetooth Module & Resuming From Sleep Mode Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation).
Modules To Add a Bluetooth Device 1. 2. Access the Bluetooth Devices control panel and click Add a device. Double-click the device you want to pair with the computer. Pairing Options If a device has been previously connected then the pairing option menu will appear when you attempt subsequent connections. You can choose to have the computer create a pairing code for you, use the device’s existing pairing code or you can pair certain devices without using a code. Figure 7 - 38 3.
Modules 4. Figure 7 - 39 Pairing Codes Pairing Code Example 7 Enter the code into your Bluetooth enabled device and follow any on-screen instructions to complete the pairing. The example outlined here shows a connection to a mobile device. Other devices e.g. computers, may have a slightly different connection procedure, and may require you to confirm a pairing code is correct on both devices. Follow the onscreen instructions to complete the pairing. 5. 6. 7.
Modules To Change Settings for the Bluetooth Device 1. 2. • • Click the taskbar icon and select Show Bluetooth Devices. Right-click on the device you want to change and click Properties to: Bluetooth Help Change the name of the device (click Bluetooth, type a new name and click OK). Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK). To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3. Click the taskbar icon and select Open Settings.
Modules 3.75G/HSPA Module (Models A & B Only) If you have included an optional 3.75G/HSPA (High Speed Packet Access) module (see “Communication” on page D - 6 for specification details) in your purchase option, you will have the appropriate application (BandLuxe HSDPA Utility) provided for your module. Follow the instructions on page 7 - 63 to install the USIM card (supplied by your service provider), and then install the application (see over for further details). 7 Important Notice - 3.
Modules 3.75G/HSPA Module USIM Card Installation Follow the instructions below to install the USIM card (which will be provided by your service provider). 1. 2. 3. 4. 5. Turn the computer off, remove the AC/DC adapter and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Slide the battery in the direction of the arrow 3 . Lift the battery out of the compartment 4 .
Modules 6. 7. Remove the battery. Insert the USIM card 5 as illustrated below until it clicks fully into position, and replace the battery. 5 7 Figure 7 - 43 USIM Card Insertion 7 - 64 3.
Modules Before installing the application, make sure that the 3.75G/HSPA module is ON (installing the driver with the module off will not allow the software to detect the module hardware correctly). Use the Fn + key combination (see “Function/Hot Key Indicators” on page 1 - 12) to toggle power to the 3.75G/HSPA module. When the 3.75G/HSPA module is powered on, the on-screen indicator will briefly be displayed. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3.
Modules BandLuxe HSDPA Utility Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + key combination to toggle power to the 3.75G/HSPA module, and check the on-screen indicator to see if the module is powered on or not (see Table 1 - 5, on page 1 - 10). With the 3.
Modules BandLuxe HSDPA - Connection Manager The connection information is stored on the USIM card supplied by the service provider (where this is not the case you may need to create a profile - see “Creating a Profile” on page 7 - 70). 1. 2. 3. Power on the 3.75G/HSPA module using the Fn + key combination. Access the Connection Manager from the Start menu (Connection Manager ), or (Start > Programs/All Programs > BandLuxe > BandLuxe HSDPA Utility R11 > Connection Manager). Click CONNECT .
Modules 4. 5. The system will connect to your network (you may need to set your network connection to home, work or public on the first connection). The connected icon will appear at the top of the utility screen. Figure 7 - 45 Connected 6. You can then access the internet, download e-mail etc. as per any internet connection. 7 Figure 7 - 46 BandLuxe Connection Manager (Connected) 7 - 68 3.
Modules 7. While you are connected the taskbar icon will display the connected icon . the taskbar will display the connected icon , and Figure 7 - 47 Taskbar Icon (Connected) 8. To disconnect from the service provider, click the Disconnect icon, or click the close icon at the top right of the utility, and click Yes to confirm. 9. The program will disconnect from the service provider. key combination 10. The module will still be on, and you will need to press the Fn + to turn it off. 11.
Modules Creating a Profile 1. 2. Access the Connection Manager from the Start menu (Connection Manager ), or (Start > Programs/All Programs > BandLuxe > BandLuxe HSDPA Utility R11 > Connection Manager). Click the Menu > Profile. 3. The default profile will display the service provider’s name from the USIM card. Figure 7 - 48 Menu - Profile 7 Figure 7 - 49 Default Profile 7 - 70 3.
Modules 4. 5. 6. 7. 8. Click New (button) and input any Network Settings required by your service provider (all fields may not need to be filled in). The profile name is used to identify your profile if a number of profiles are used. You will need to check with your service provider to confirm if the User Name and Password are required. You will need to enter the Access Point Name and phone Number as supplied by the service provider. Click Save to save the profile.
Modules 9. New SIM Card 7 If you switch to a different SIM card, then the default profile will no longer be valid. You will need to create a new profile as described here. If you do not have access to all the information necessary to create a new profile you should uninstall the BandLuxe software and then reinstall it. The new default profile should obtain the information from the SIM card.
Modules Choosing a Profile If you need to switch stored profiles follow the instructions below: 1. 2. 3. 4. 5. Access the Connection Manager from the Start menu (Connection Manager ), or (Start > Programs/All Programs > BandLuxe > BandLuxe HSDPA Utility R11 > Connection Manager). Click the Menu > Profile. Highlight the profile required and click Default. Click OK to confirm. YES will be displayed alongside the chosen default profile. Figure 7 - 52 Choosing a Profile 3.
Modules Editing a Profile Get the Latest Access Point Name Database 7 The Profile menu allows you to update the Access Point Name (APN) list. When the network connection is established, click the Get the latest APN list database (button) to update the information. If you need to edit stored profiles follow the instructions below: 1. 2. 3. 4.
Modules Text Messaging Service (SMS) In addition to standard internet services you may also send and receive SMS text messages using the Connection Manager, if your service supports SMS. Inbox The Inbox will contain any received SMS. Click to select the message and it will scroll open above. Select the message and press the Save, Delete or Reply buttons to perform the appropriate function. Unread messages are displayed as closed envelope icons , and read messages are open displayed as envelope icons .
Modules Contact List Types Select a contact from the SIM card. Select a contact from the Outlook address book. 7 Select a contact from the BandLuxe contact list. Sent The Sent folder contains any successfully sent SMS. Select the message and press the Delete to erase the record. Outbox The Outbox folder contains any completed but unsent SMS. Select the message and press Send or Delete as appropriate. Compose Click Compose to create a new message.
Modules Template A template can store text that is used regularly in messages, and can be easily inserted in to any new SMS. Click Template (button) to view any stored templates. Click to highlight a template and click Select (button) to insert it into the message. Click New (button) to create a new template, and Save (button) to add it to the existing list. To delete a template click to highlight it, and click Delete (button) to delete it.
Modules Language 7 The Connection Manager offers multiple language interfaces. Click the menu and select a language from the dropbox. Click Save (button) to implement the changes. You will then return to the home screen with chosen language selected. Setting The Setting menu allows you to edit the programs basic parameters. 1. 2. 3. 4.
Modules SMS - Preference Click the New SMS Notify checkbox to be automatically notified when a new SMS arrives. If enabled a the incoming message notification will appear in the taskbar, Figure 7 - 58 Incoming SMS Notification and an envelope icon will appear in the upper left corner of the Home screen when a new message arrives.
Modules SIM This menu allows you to edit the USIM card Personal Identification Number (PIN) and Enable/Disable the PIN if necessary. Press Apply after making any changes. A SIM card must be inserted for this function to be activated. Figure 7 - 60 Setting - SIM 7 If a PIN code is enabled, the input will be requested during USIM card initialization. After 3 incorrect PIN code entries the USIM card will be locked, and you will need to contact your service provider to unlock it. 7 - 80 3.
Modules Radio Set the appropriate network search options from the dual mode setting menu. Click Apply (button) after making any changes. Figure 7 - 61 Setting - Radio 7 Note: 2G/3G/3.5G data transferring will be disconnected when you apply a new Radio setting. 3.
Modules Network Setting Note that the network settings can only be accessed for editing if the program is not connected to a network. Network - Network Selection Edit the network selection settings from this menu. The Standard (auto) setting will search for networks in the order specified in the Prefer list. Click Standard (auto) > Next to view and adjust the Prefer list. The Prefer list is displayed at the top of the screen, and the bottom of the screen lists all available networks.
Modules The Manual setting allows you to choose a network from all available. Click Manual > Next to view the list. Click to highlight a network from the list, and click Select (button) to choose the network, or Cancel (button) to make no change. Figure 7 - 63 Setting - Network Manual 7 3.
Modules Statistics & Information The Statistics screen displays a graph of recent upload and download activity. No data will be displayed if there is no current connection. 1. 2. 3. 7 Access the Connection Manager from the Start menu (Connection Manager ), or (Start > Programs/All Programs > BandLuxe > BandLuxe HSDPA Utility R11 > Connection Manager). Click the Menu > Statistics. Click Connection Log (tab) to see data counting by each and total connection status (for reference only).
Modules TV Tuner Module (Model C Only) If your purchase configuration includes the optional USB Mini-Card TV Tuner module, you will be supplied with a remote control unit and appropriate fittings for the module. Software support for the TV Tuner module is provided by Windows Media Center in Windows 7 (not included in Starter or Home Basic versions). A driver is provided on the Device Drivers & Utilities + User’s Manual disc for the remote control supplied with the TV Tuner.
Modules TV Tuner Module Support 7 Note that the TV Tuner module options in Windows 7 is supported by the Windows Media Center software which comes built-in to all the Windows 7 versions except Starter and Home Basic. If your purchase includes a TV Tuner option, and you are reconfiguring your system for a different system, you should install any Windows 7 version except Starter and Home Basic. Consumer Infrared Driver 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive.
Modules Digital TV Broadcast Signal The antenna is the most crucial factor in receiving a clear digital terrestrial TV broadcast signal. The passive antenna provided should provide a clear signal when placed beside a window. If the signal is not clear then you can purchase an active antenna (it should also be placed beside a window) to improve the signal. You should also check with any related government website which provides information on digital terrestrial TV coverage for your area.
Modules THX TruStudio & Speaker Configuration Note that THX TruStudio Pro will be disabled when you are connecting to an external display through an HDMI connection. 7 THX TruStudio Pro Audio Install the THX TruStudio AP to allow you to configure the audio settings to your requirements for the best performance in games, music and movies. THX TruStudio AP Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers (button). 3. Click 6.
Modules THX TruStudio Pro Activation On the first run of THX TruStudio Pro you will need to activate the application. 1. 2. 3. 4. 5. To activate the application you will need to be connected to the internet. Double-click the THX Activate icon on the desktop and click the Activate button. The program will connect to the internet to verify the activation key. Click Finish to complete the application activation. Restart the computer after the process is complete.
Modules THX Control Panel Each control has an On/Off button to allow you to enable/disable the control, and most controls feature a slider to adjust the levels (the subwoofer may be turned on/ off). Menu Figure 7 - 67 THX TruStudio Pro Controls 7 Surround: Provides virtual sound channels to control the level of immersion. Crystalizer: Enhances audio to make it sound livelier. Speaker: Enhances the bass level of the sound system.
Modules THX TruStudio Pro & HDMI 1. 2. 3. When you connect an HDMI display to the HDMI-Out port,the THX Tru Studio Pro controls will be disabled. A warning box will pop-up and will prompt “Do you want to select another audio device now?”. Click No to continue using the HDMI audio output from your external display (do not attempt to select another audio device when connected to the external HDMI display).
Modules 7 7 - 92
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power Indicators (see “LED Indicators” on page 1 - 9) to see the computer’s power status. • Connections - Check all the cables to make sure that there are no loose connections anywhere.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Don’t over complicate things. The less you have to deal with then the easier the source of the problem may be found; Example - if your computer has many devices plugged into its ports, and a number of programs running, then it will be difficult to determine the cause of a problem. Try disconnecting all of the devices and restarting the computer with all the peripheral devices unplugged.
Troubleshooting Problems & Possible Solutions Problem Possible Cause - Solution You turned the power on but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The Battery LED power indicator , is blinking orange. Low Battery. Plug in the AC power source.
Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the vents/fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 15). Make sure you’re using the correct adapter.
Troubleshooting Problem You forget password. the Possible Cause - Solution boot If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting 8 Problem Possible Cause - Solution The TouchPad doesn’t work. The Touchpad has been disabled. Press the Touchpad toggle (Fn + F1) key combination (make sure you have installed the Touchpad driver. The system freezes or the screen goes dark. The system’s power saving features have timed-out. Use the AC/DC adapter, press a key on the keyboard, or press the sleep (Fn + F4) key combination, or press the power button if no LEDs are lit. The system never goes into a power saving mode.
Troubleshooting Problem Possible Cause - Solution When a DVD is played in Windows Media Player/ Media Center, the audio track in other languages (commentaries etc.) is not clear if connected to the S/PDIF-Out Jack. This is an issue with Windows Media Player/Media Center and audio output through the S/PDIFOut Jack. We recommend that you use the Power DVD application to play DVDs. Nothing appears on the screen when the PC Camera software is run.
Troubleshooting 8 Problem Possible Cause - Solution No sound can be heard through an HDMI connected display device. You have not configured the HDMI audio output. See “HDMI Audio Configuration” on page B 13. Audio Volume is too low when listening through headphones. You have set the Speaker Configuration to 5.1 or 7.1 Speaker. It is recommended that you set the Speaker Configuration to Stereo (not to 5.1 or 7.1 Speaker) when listening through headphones in order to maximize audio quality.
Troubleshooting Bluetooth Connection Problems If you are experiencing problems connecting to some Bluetooth devices (in particular certain mobile phones and headsets) it maybe necessary to download and install the Windows Mobile Device Center software (for Windows Vista and Windows 7). Go to the Microsoft website and search for the Microsoft Windows Device Center Driver for Windows Vista (64-bit or 32-bit) and Windows 7 (64-bit or 32-bit), and then download the driver. 1. 2. 3. 4. 5.
Troubleshooting 6. 7. 8. 8 Right-click Bluetooth Peripheral Device and click on Update Driver Software. Click Browse my computer for driver software. Click Let Me pick from a list of device drivers on my computer. Figure 8 - 2 - Browse my computer.../Let me pick from... 9. Select Bluetooth Radios from the list.
Troubleshooting 10. A list of drivers will appear with Manufacturer on one side and Model in the other. 11. Choose Microsoft Corporation (make sure you choose the full name Microsoft Corporation and do not choose Microsoft - Note that you must have installed the Microsoft Windows Device Center Driver for Microsoft Corporation to appear in the list). 12. Select Windows Mobile-based device support from the Model list. 8 Make sure you select Microsoft Corporation Figure 8 - 4 - Select Device Driver 13.
Troubleshooting 15. The Device Manager should now display the Windows Mobile-based device support under Bluetooth Radios. 16. You will need to repeat the process for any other Bluetooth Peripheral Devices listed under Other Devices.
Troubleshooting Intel® Centrino Advanced 6230 WLAN & Bluetooth V3.0+HS Combo Modules Note that, at the time of going to press, Intel® Centrino Advanced 6230 WLAN & Bluetooth V3.0+HS combo modules use the standard Bluetooth configuration in Windows 7 (see “Intel Bluetooth Combo Driver Installation” on page 7 - 57). Do not use the Bluetooth & WLAN Combo settings information outlined from page 7 50 to page 7 - 56.
Troubleshooting Installing Windows 7 (pre Service Pack 1) for RAID Systems with Advanced Format Disks The following information is only applicable under the following conditions: • You are configuring your SATA hard disks in a RAID. • You are using Advanced Format hard disks that have a 4KB physical sector size. • You are using a Windows 7 version that DOES NOT include Service Pack 1 on the DVD disc. Windows 7 versions pre Service Pack 1 (i.e.
Troubleshooting 4. Press a key at system startup to begin installing Windows from your Microsoft Windows 7 disc (make sure the DVD device is set at the top of the Boot Sequence in the BIOS - see “Boot Sequence (Boot Menu)” on page 5 - 14). 5. Click Install Now. 6. Make sure your USB Flash drive, external USB hard disk or external USB floppy disk drive and floppy diskette is attached to one of the USB ports on the computer. 7. Click “I accept the license terms” tickbox and click Next. 8.
Troubleshooting 8 8 - 20
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the ports & jacks which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Ports and Jacks Item Card Reader Description The card reader allows you to use the following digital storage cards: MMC (MultiMedia Card) / RSMMC SD (Secure Digital) / Mini SD / SDHC / SDXC Compatible MS (Memory Stick) / MS Pro / MS Duo Push the card into the slot and it will appear as a removable device. A Cable (CATV) Antenna Jack (Model C Only) Use this jack to connect a CATV cable if you have included the optional Mini-PCI TV Tuner in your purchase for Model C computers.
Interface (Ports & Jacks) Item Description e-SATA / USB 2.0 Combo Port /e-SATA / This e-SATA (external Serial Advanced Technology Attachment) port allows you to plug-in external Serial ATA hard drives. This port also serves as a USB 2.0 port. HDMI-Out Port HDMI The HDMI-Out (High-Definition Multimedia Interface) port is an audio/video connector interface for transmitting uncompressed digital streams. This allows you to connect an external monitor, TV or Flat Panel Display etc.
Interface (Ports & Jacks) Item Description Mini-IEEE 1394a Port This allows high-speed connection to various peripheral devices, e.g. external disk drives and digital cameras (see note below). IEEE 1394a The Mini-IEEE 1394 ports only support SELF POWERED IEEE 1394 devices. A RJ-45 LAN Jack This port supports LAN (Network) functions. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port.
Interface (Ports & Jacks) Item Description USB 2.0/1.1 Ports These USB (Universal Serial Bus) 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc.
Interface (Ports & Jacks) A A - 6
NVIDIA Video Driver Controls Appendix B: NVIDIA Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 16. NVIDIA Video Driver Installation Video Card Options Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Note that card types, specifications and drivers are subject to continual updates and changes.
NVIDIA Video Driver Controls NVIDIA Control Panel To access the GeForce..... control panel from the desktop; rightclick the desktop, then click NVIDIA Control Panel. NVIDIA Control Panel (Win 7) More advanced video configuration options are provided in the NVIDIA Control Panel tab. 1. 2. Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click NVIDIA Control Panel (click "Classic View" from the left of the menu if you are in Control Panel Home).
NVIDIA Video Driver Controls The NVIDIA Control Panel provides additional video configuration controls and tools which allow quick access to features such as display configuration, 3D Settings and Help menus etc. Navigating the Control Panel Navigate through the control panels in much the same way as you would a web page. Click on the sub-heading tasks in the left menu (and on the highlighted links) for information. Use the buttons on the top left to go back, forward etc.
NVIDIA Video Driver Controls The Help menus provide index and search features, and direct links to the NVIDIA website etc.
NVIDIA Video Driver Controls Display Devices Note that you can use a DVI cable connected to the DVI-Out port, or an HDMI (High-Definition Multimedia Interface) cable connected to the HDMI-Out port to connect an external display (if you are using an older type of monitor you can use a converter to convert the signal from DVI to VGA). See your display device manual to see which formats are supported. 1. 2. 3. The built-in LCD. An external display connected to the DVI-Out Port.
NVIDIA Video Driver Controls Display Modes Single Display Mode Only one of your displays is used. Duplicate Displays Duplicate simply shows an exact copy of the Primary display desktop on the other display(s). This mode will drive multiple displays with the same content. Extend Desktop Extend Desktop treats both connected displays as separate devices, and they act as a virtual desktop resulting in a large workspace. When enabled, you can drag any icons or windows across to the other display desktop.
NVIDIA Video Driver Controls Configuring an External Display using the NVIDIA Control Panel You can use the NVIDIA control panel to configure any attached displays. 1. 2. 3. 4. Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on. Go to NVIDIA Control Panel (see page B - 2). Double-click Display (if the sub-menus are not visible), and then click Set up multiple displays. Any attached display will appear under “1.Select the displays you want to use.
NVIDIA Video Driver Controls Duplicating the Displays 1. 2. 3. 4. 5. 6. Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on. Go to NVIDIA Control Panel (see page B - 2). Double-click Display (if the sub-menus are not visible), and then click Set up multiple displays. Any attached display will appear under “1.Select the displays you want to use.” Click the tickbox alongside any display you wish to use. Right-click one of the display icons and click “Duplicate displays....
NVIDIA Video Driver Controls Extending the Display 1. 2. 3. 4. 5. Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on. Go to NVIDIA Control Panel (see page B - 2). Double-click Display (if the sub-menus are not visible), and then click Set up multiple displays. Click to select a primary display under “1.Select the displays you want to use.” Right-click one of the display icons and click “Extend Desktop on this display....” to extend the desktop across both displays.
NVIDIA Video Driver Controls Function Key Combination You can use the Fn + F7 key combination to toggle through the display options: Attaching Other Displays (Win 7) Configuring an External Display in Windows 7 1. 2. 3. 4. Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on. Go to the Screen resolution control panel. Click the Detect button. The computer will then detect any attached displays.
NVIDIA Video Driver Controls 5. You can configure the displays from the Multiple Displays menu. Figure B - 8 Screen Resolution Multiple Display Options (Win 7) B • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) • Extend these displays - Treats both connected displays as separate devices • Show desktop only on 1/2 - Only one of your displays is used.
NVIDIA Video Driver Controls Using the Windows Logo Key + P Key Combination to Switch Displays You can also use the + P key combination to quickly change display configuration and modes (this is particularly useful when attaching a projector) in Windows 7. 1. 2. 3. 4. Attach your external display to the external monitor port and turn it on. + P key combination. Press the An on-screen menu will pop up.
NVIDIA Video Driver Controls HDMI Audio Configuration As HDMI (High-Definition Multimedia Interface) carries both audio and video signals you can configure the audio output from the NVIDIA control panel and Sound control panel. The settings will depend upon the external HDMI display you have connected to. When you connect a display to the HDMI-Out Port then the Set up digital audio item will appear under Display. Click “Change Windows Sound Settings” (button) to access the Sound control panel.
NVIDIA Video Driver Controls Windows Audio Setup for HDMI In some cases it will be necessary to go to the Sound control panel and manually configure the HDMI audio output. 1. 2. 3. 4. 5. 6. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound). Click Playback (tab) The playback device will be selected. In some cases you may need to select the audio device and click Set Default (button). Double-click the device to access the control panel tabs.
NVIDIA Video Driver Controls 7. 8. Adjust the HDMI settings from the control panel tabs. Click OK to close the Sound control panel.
NVIDIA Video Driver Controls Other Applications If you are using a third party application to play DVDs etc. you will need to consult the application’s documentation to see the appropriate audio configuration (the application must support digital to analog translation). HDMI Notes • Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device.
NVIDIA Video Driver Controls HDCP Status If your external display is HDCP (High Bandwith Digital Content protection) compatible then the NVIDIA control panel will display the HDCP system status.
NVIDIA Video Driver Controls B B - 18
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your service center for details.
Specifications Processor Processor Memory Note all processor packages are rPGA988B Models A, B & C: Intel® Core i7-2820QM (2.3GHz) Quad-Core Mobile Processor 8M L3 Cache, 32nm (32 Nanometer), DDR3-1600MHz, TDP 45W Dual Channel DDRIII (DDR3) Models A& C Only: Intel® Core i7-2920XM (2.5GHz) Extreme Quad-Core Mobile Processor 8M L3 Cache, 32nm (32 Nanometer), DDR3-1600MHz, TDP 55W =============================== Model B Only: Intel® Core i3-2310M (2.
Specifications Video Adapter Options Video Adapter Options Storage Models A, B & C: nVIDIA® GeForce GTX 460M PCIe * 16 Video Card 1.5GB GDDR5 Video RAM On Board Supports Microsoft DirectX® 11.0 Supports HDCP Supports DVI Dual Link Supports HDMI 1.4 NVIDIA PhysX™ GeForce CUDA™ Technology Model C: nVIDIA® GeForce GTX 470M PCIe * 16 Video Card 1.5GB GDDR5 Video RAM On Board Supports Microsoft DirectX® 11.0 Supports HDCP Supports DVI Dual Link Supports HDMI 1.
Specifications Keyboard & Pointing Device Interface Card Reader Full Size Winkey Keyboard with Numeric Keypad with WASD Gaming Marking Built-In TouchPad (with Multi Gesture Functionality) Model C: One CATV Input Jack for TV Antenna (for TV Tuner Mini-Card) Embedded Multi-In-1 Card Reader - MMC / RSMMC - SD / Mini SD / SDHC / SDXC Compatible - MS / MS Pro / MS Duo Slots Interface Two Mini-Card Slots: Two USB 3.0 Ports Two USB 2.0 Ports (Note: One USB2.
Specifications Communication Power Management Environmental Spec 2.0M Pixel PC Video Camera Module Supports Wake on LAN Supports Wake on USB Temperature Operating: 5°C - 35°C Non-Operating: -20°C - 60°C Models A & B: UMTS/HSPDA-based 3.
Specifications C C - 6
