V13.1.
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
Preface CE Marking This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place it on an unstable surface. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company. • The power adapter may have either a 2-prong or a 3-prong grounded plug.
Preface Polymer Battery Precautions Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf. • Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern. • Use proper handling procedures when using polymer batteries.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface Contents Notice .............................................................................................................................................................I ErP Off Mode Power Consumption Statement: ........................................................................................... II FCC Statement ............................................................................................................................................
Preface System Map: LCD Panel Open - Model A ................................................................................................1-7 System Map: LCD Panel Open - Model B ................................................................................................1-8 LED Indicators ...........................................................................................................................................1-9 Keyboard - Model A .....................................................
Preface Running Apps ..........................................................................................................................................1-35 Features & Components Overview ....................................................................................................................................................2-1 Hard Disk Drive .........................................................................................................................................
Preface Power-Saving States ..................................................................................................................................3-7 Sleep ..........................................................................................................................................................3-7 Hibernate ....................................................................................................................................................3-8 Shut down ..............
Preface Windows Security Message .......................................................................................................................4-5 New Hardware Found ................................................................................................................................4-5 Driver Installation Procedure .....................................................................................................................4-6 Chipset ..............................................
Preface System Time & Date (Main Menu) ...........................................................................................................5-5 SATA Port # (Main Menu) ........................................................................................................................5-6 System/Extended Memory: (Main Menu) .................................................................................................5-6 MB Series / BIOS Revision / KBC/EC firmware Revision ........................
Preface UEFI Boot (Boot Menu) ..........................................................................................................................5-17 Exit Menu ................................................................................................................................................5-18 Upgrading The Computer Overview ....................................................................................................................................................
Preface 3rd Party 802.11b/g/n Driver Installation ................................................................................................7-13 Intel® WLAN Driver Installation ............................................................................................................7-13 WLAN Configuration in Windows .........................................................................................................7-14 Bluetooth & WLAN Combo Module ..............................................
Preface EM820W 3G Module PIN Code & Power-Saving ..................................................................................7-55 Wireless Display ......................................................................................................................................7-57 Wireless Display Configuration ..............................................................................................................7-58 Troubleshooting Overview ................................................
Preface Dynamic Video Memory Technology ......................................................................................................C-1 Intel® HD Graphics Control Panel ...........................................................................................................C-2 Display Devices & Options ....................................................................................................................C-15 Attaching Other Displays ..................................................
Preface Security .....................................................................................................................................................D-4 Features .....................................................................................................................................................D-4 Operating System ......................................................................................................................................D-4 Indicators ..............
Preface XXVIII
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 • Chapter 3 • Chapter 4 • Chapter 5 • Chapter 6 • Chapter 7 • Chapter 8 • Appendix A • Appendix B • Appendix C • Appendix D A guide to using some of the main features of the computer e.g.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a of interest to you.
Quick Start Guide Not Included Operating Systems (e.g. Windows 8.1) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g.
1 Quick Start Guide System Startup 1. 2. 3. 4. 5. Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 8.1 operating system is supported. Note: In order to run Windows without limitations or decreased performance, your computer requires a minimum 1GB of system memory (RAM). Windows Versions Note that the information included on the following pages is for Windows 8.1 only.
1 Quick Start Guide Model Differences This notebook series includes two different models that vary slightly in design style, color, power button style, general appearance and features supported (see Appendix D for full details). Note that your computer may look slightly different from that pictured throughout this manual.
Quick Start Guide System Map: LCD Panel Open - Model A 2 1 3 Wireless Device Operation Aboard Aircraft 4 5 6 Figure 1 - 2 LCD Panel Open Model A The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the WLAN & Bluetooth module(s) are OFF if you are using the computer aboard aircraft by putting the system in to Airplane Mode (see Table 1 - 3, on page 1 13). 1. 2. 3. 4. 5. 6. 7.
1 Quick Start Guide Figure 1 - 3 LCD Panel Open Model B 1. 2. 3. 4. 5. 6. 7. System Map: LCD Panel Open - Model B 1 2 Built-in PC Camera (Optional) PC Camera LED Built-In Microphone LCD Power Button Keyboard Touchpad & Buttons 3 Wireless Device Operation Aboard Aircraft 4 5 6 The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Quick Start Guide LED Indicators The LED indicators on the computer display helpful information about the current status of the computer.
1 Quick Start Guide Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot-keys unique to the system’s regular keyboard may not work. Keyboard - Model A The keyboard has an embedded numerical keypad for easy numeric data input, and function keys to change operational features instantly.
Quick Start Guide Keyboard - Model B The keyboard has an embedded numerical keypad for easy numeric data input, and function keys to change operational features instantly. Function Keys NumLk & ScrLk Keys Play/Pause Key Numerical Keypad Fn Key Windows Logo Key Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically.
1 Quick Start Guide Windows Logo Keyboard Shortcut Use the Windows logo key + D key combination to switch between the Start screen and Windows Desktop. Keyboard Shortcuts The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navigation/operation in Windows 8.1.
Quick Start Guide Function/Hot Key Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility is installed.
1 Quick Start Guide Control Center When in the Windows Desktop application (not in the Start screen) press the Fn + Esc key combination, or double-click the icon in the notification area of the taskbar to toggle the Control Center on/off. The Control Center gives quick access to frequently used controls and enables you to quickly turn the camera/Touch Pad on/off (see Appendix B for full details). Control Center Click on any button to turn any of the modules (e.g. TouchPad, Camera) on/off.
Quick Start Guide System Map: Front & Left Views Figure 1 - 6 Front & Left Views 1 1. 2. 2 3 4 5 6 7 8 3. 4. 5. 6. Multi-In-1 Card Reader 7. 8. LED Indicators Multi-in-1 Card Reader DC-In Jack RJ-45 LAN Jack External Monitor Port Vent/Fan Intake/ Outlet HDMI-Out Port 2 * USB 3.0 Ports The card reader allows you to use the most popular digital storage card formats: MMC (MultiMedia Card) / RS MMC SD (Secure Digital) / Mini SD / SDHC / SDXC MS (Memory Stick) / MS Pro / MS Duo USB 3.
1 Quick Start Guide Figure 1 - 7 Right & Rear Views 1. Microphone-In Jack 2. Headphone-Out Jack 3. 1 *USB 2.0 Port (Model A) OR 2 *USB 2.0 Ports (Model B) 4. Optical Device Drive Bay (for CD/ DVD Device) 5. Security Lock Slot 6. Battery System Map: Right & Rear Views Model A 1 2 4 3 5 Model B 1 2 3 4 3 5 6 Battery Information W255EU Always completely discharge, then fully charge, a new battery before using it.
Quick Start Guide Disk Eject Warning Changing DVD Regional Codes Don’t try to eject a CD/DVD while the system is accessing it. This may cause the system to “crash”. Stop the disk first then eject it, or press the stop button twice. Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives.
1 Quick Start Guide Figure 1 - 8 Bottom View Model A 1. 2. 3. 4. 5. System Map: Bottom View - Model A 1 Battery Component Bay Cover Vent/Fan Intake/ Outlet Hard Disk Bay Cover Speakers 3 2 3 4 3 3 5 5 CPU Overheating The CPU is not a user serviceable part. To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.
Quick Start Guide System Map: Bottom View - Model B Figure 1 - 9 Bottom View Model B 1 1. 2. 3. 2 4. 5. 3 3 4 Battery Component Bay Cover Vent/Fan Intake/ Outlet Hard Disk Bay Cover Speakers 3 5 5 Overheating CPU To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use. The CPU is not a user serviceable part.
1 Quick Start Guide Windows Versions Note that the information included on the following pages is for Windows 8.1 only. The Windows 8 interface is slightly different in appearance and in methods of navigation, and a separate manual is provided on the Device Drivers & Manual Disc with reference to Windows 8. Windows 8.1 Control Panel Throughout this manual you will see an instruction to open the Control Panel.
Quick Start Guide Right-click the Start button in the Desktop app (or use the Windows Logo Key + X key combination) to bring up an advanced context menu of useful features such as Control Panel, Programs and Features, Power Options, Task Manager, Search, File Explorer, Command Prompt, Device Manager and Network Connections etc.
1 Quick Start Guide Windows 8.1 Start Screen & Desktop The Apps, control panels, utilities and programs within Windows are accessed from the Start screen and/or Windows Desktop app. The Desktop (which runs as an app within the Start screen) can be accessed by clicking the Desktop item in the Start screen (or by using the Windows Logo Key + D key combination). Click the arrow at the bottom of the Start screen to access Apps. Desktop App Figure 1 - 12 - Windows Start Screen 1 - 22 Windows 8.
Quick Start Guide Apps & Tiles The Start screen will contain a number of apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on one screen so you will often need use the slider at the bottom of the screen in order to view all the necessary Apps. Accessing Pining/Unpinning All Apps You can add and remove the tiles for apps and control panels in the Start screen. Right-click on a blank area of the Start screen, and you will see the Customize icon.
1 Quick Start Guide Desktop Application When the Desktop app is running (click the app in the Start screen or use the Windows Logo Key + D key combination) you can use lower left hot corner to switch between the Start screen and the Windows Desktop app. To do so move your mouse to hover over the bottom left corner of the Desktop app and left-click. When you move to the lower left hot corner in the Start screen it will take you back to your most recently used app (if one is running).
Quick Start Guide The Charms Bar The right side of the screen displays the Charms Bar. The Charms Bar contains the Search, Share, Start, Devices and Settings menus. To access up the Charms Bar move the cursor to the upper or lower right corners of the screen, and then hover over one of the items in the Charms Bar to activate it (the bar will be black when it is active), or use the Windows Logo Key + C key combination.
1 Quick Start Guide Charms Bar Items • Search results. • Share : You can search for any file, application, Apps and control panel settings with instantaneous : This button is used to share information with people via mail or social networks. • Start : Click to bring up the Start screen (the same function as pressing the Windows Logo Key or clicking the bottom left of the screen). • Devices : Click this button to change connected peripheral device settings e.g. an external display.
Quick Start Guide Windows 8.1 Control Panel In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel can be accessed in a number of ways in Windows 8.1. • Click Search in the Windows Charms Bar (see previous page) and the search pane will pop out. Type Control Panel and select it from the results to the left.
1 Quick Start Guide • When in the Desktop app (this does not apply to the Start screen) click on Settings in the Windows Charms Bar and select Control Panel from the menu. Figure 1 - 19 - Settings Charms Bar (Desktop App Only) • Click the arrow at the bottom of the Start screen and click Control Panel in Apps (Windows System). Figure 1 - 20 - All Apps - Control Panel 1 - 28 Windows 8.
Quick Start Guide • Right-click the Start button to bring up the menu and select Control Panel (see Figure 1 - 11 on page 1 - 21). Keyboard Shortcut to Control Panel You can also use keyboard shortcuts to access the Control Panel. Press the Windows logo key and X to bring up the context menu, and then press P to bring up the Control Panel. Alternatively press the Windows logo key and R to bring up the Run dialog box, and then type “Control Panel” and press Enter to access the Control Panel. Windows 8.
1 Quick Start Guide Windows 8.1 Taskbar In many instances throughout this manual you will see an instruction to access the notification area of the taskbar (system tray). In Windows 8.1 the taskbar is accessed from the Desktop application; if you are in the Start screen you will need to switch to the Desktop. The taskbar is displayed at the bottom of the Desktop screen, and you can see the notification area (system tray) of the taskbar in the bottom right of the screen.
Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display control panel (in Appearances and Personalization) in Windows when running the Desktop app (see “Desktop Application” on page 1 - 24 and Appendix C). It is possible to quickly configure external displays from the Devices menu item in the Charms Bar (see “The Charms Bar” on page 1 - 25). To Configure Displays from Devices (Charms Bar): 1. 2. 3. 4.
1 Quick Start Guide To access Display (Control Panel) and Screen Resolution in Windows: 1. 2. 3. Go to the Control Panel. Click Display (icon) - In the Appearance and Personalization category. Adjust resolution. Right-Click Desktop App You can right-click the desktop and select Screen resolution 1 (Figure 1 23). 2 Use the dropbox to select the screen Resolution 2 (Figure 1 - 23). Click Advanced settings 3 (Figure 1 23) to bring up the Advanced properties tabs.
Quick Start Guide To access the Intel(R) HD Graphics Control Panel: 1. 2. Click Advanced settings 3 (Figure 1 - 23 on page 1 - 32) in the Screen Resolution control panel in Windows. Click the Intel(R)... tab and click Graphics Properties (button) 4 (Figure 1 - 24 on page 1 - 33) . OR 3. Right-click the desktop and select Graphics Properties from the menu. OR 4. Click the icon in the notification area of the Desktop taskbar and select Graphics Properties from the menu.
1 Quick Start Guide Power Options Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power Menu item in Settings in the Charms Bar in Windows 8.1 may be used to Shut down or Restart (you can also add Hibernate/ Sleep to the menu - see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 10). You can also use the context menu (Shut down or sign out) shut the computer down/restart etc. Shut Down, Restart or Sleep (Charms Bar) 1. 2. 3. Go to the Charms Bar and click Settings.
Quick Start Guide Running Apps To run apps in Windows 8.1 you will need to check that the Screen Resolution and User Account Control Settings are compatible with the system requirements. Screen Resolution Settings 1. 2. Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination). Right-click a blank area of the Windows Desktop and select Screen Resolution.
1 Quick Start Guide User Account Control Settings If your computer meets the minimum screen resolution requirements, and still you can't run apps, then that you have to check the status of User Account Control (UAC). Apps may fail to open when the UAC is turned off. To check whether the UAC is on or off, follow the instructions below. 1. 2. 3. 4. Open the Control Panel.
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • Hard Disk Drive Optical (CD/DVD) Device Multi-In-1 Card Reader TouchPad and Buttons/Mouse Audio Features Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (9.5mm height). The actual device will depend on the module you purchased (see “Storage” on page D - 2). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 16).
Features & Components 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Features & Components DVD Regional Codes To change the DVD regional codes: 1. 2. 3. Go to the Control Panel Double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code.
Features & Components 2 Card Reader Cover Make sure you keep the rubber cover provided in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. Multi-In-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Features & Components TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details.
Features & Components 2 TouchPad Scrolling This computer model series may feature different TouchPad versions. Once you have installed the TouchPad driver (see “Touchpad” on page 4 - 6) you can configure the functions from the Mouse control panel in Windows, or by doubleclicking the TouchPad driver icon in the notification area of the taskbar in the Desktop app. You may then configure the TouchPad tapping, buttons, scrolling, pointer motion and sensitivity options to your preferences.
Features & Components Gestures and Device Settings The Synaptics Gestures Suite application allows you to use a specific gesture (action) on the surface of the Touchpad to perform specific actions to manipulate documents, objects and applications. You can configure the settings from the Device Settings tab in Mouse Properties: 1. 2. 3. 4. Go to the Control Panel. Click Mouse (Hardware and Sound). Click Device Settings (tab) and click Settings.
Features & Components Disabling the Touchpad If you need to disable the Touchpad for any reason (e.g. you may find that when using the computer’s internal keyboard you accidentally trigger the Touchpad when resting your wrists or palms on it) you can do so by using Fn + F1 key combination. 2 You can also set the system to automatically disable the internal Touchpad when an external USB point device (e.g a USB mouse) is attached. 1. 2. 3. 4. Go to the Mouse Properties control panel.
Features & Components Scrolling The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the TouchPad surface and slide both fingers in the direction required (in a straight continuous motion). 2 Figure 2 - 8 Scrolling Gesture Zooming The Pinch Zoom gesture can be used to perform the same function as a scroll wheel in Windows applications that support CTRL + scroll wheel zoom functionality.
Features & Components Rotating Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the TouchPad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.
Features & Components Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar notification area/control panel (right-click the taskbar notification area icon to bring up an audio menu). The volume may also be adjusted by means of the volume icon in the taskbar or the audio slider in the Settings menu (see sidebar).
Features & Components Setup for Audio Recording 2 To record audio sources on your computer at optimum quality follow the instructions below: 1. 2. 3. 4. Figure 2 - 13 Realtek Audio Manager Recording Setup 2 - 14 Audio Features Go to the Control Panel. Click Realtek HD Audio Manager (Hardware and Sound), or right-click the taskbar icon and select Sound Manager.
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management 3 Forced Off If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the system to turn itself off. The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. 4.
Power Management Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options (Hardware and Sound) in the Windows control panel to configure this feature.
Power Management Shutting the Computer Down Note that you should always shut your computer down by choosing the Shut down command as this will help prevent hard disk or system problems. Use the Shut down or sign out item in the Context Menu (right-click the lower left corner of the screen to bring up the menu). 3 You can also use the Power Menu in Settings in the Windows Charms Bar. If you want to add Hibernate/Sleep to the Power Menu see “” on page 3 - 9.
Power Management Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one. The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity. Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). 3 Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source.
Power Management Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off. Windows uses the Sleep, Hibernate and Shut Down power-saving states. Sleep In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu. Password Protection It is recommended that you enable a password on wake up in order to protect your data.
Power Management Adding Hibernate/Sleep to the Power Menu Add Hibernate/Sleep to the Power Menu as follows. 1. 2. 3. 4. 5. 3 Go to the Power Options (Hardware and Sound) control panel. Click “Change settings that are currently unavailable” Click Choose what the power buttons do. Click to put a tick in the Hibernate/Sleep box under Shutdown settings. Click Save Changes and close the control panel. Figure 3 - 6 Power Options Define Power Buttons - Shutdown Settings 3 - 10 Configuring the Power Buttons .
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo).
Power Management 3 Power Conservation Modes The Energy Star setting will result in maximum power saving, but with the possible loss of some performance. Power Conservation Modes This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. Adjust Power Conservation Modes from the Control Center: 1. 2. 3. Press the Fn + Esc key combination to toggle the Control Center on/off.
Power Management Ctrl + Alt + Delete Key Combination You can use the CTRL + ALT + DEL key combination from almost any of the Windows 8 interfaces/Apps to bring up a full-screen displaying Lock, Switch User, Log off, Change a password and Task Manager options. If you click the Power icon in the lower right corner of the screen a power management option menu appears to display Sleep, Shut down, and Restart.
Power Management 3 Low Battery Warning When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted. Battery Information Follow these simple guidelines to get the best use out of your battery. Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g.
Power Management Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter. • Reduce the amount of time before the display is turned off. • Close wireless, Bluetooth, modem or communication applications when they are not being used.
Power Management Battery Life 3 Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. It is recommended that you use the Battery Settings in the Energy Save Utility to help maintain the life of the battery. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see “Removing the Battery” on page 6 - 3.
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Caution Danger of explosion if battery is incorrectly replaced. Damaged Battery Warning Should you notice any physical defects (e.g.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 3 1. 2. Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 3. Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options.
Power Management How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Power Management 3 3 - 22
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation 1. 2. 4 3. 4. Insert the Device Drivers & Utilities + User’s Manual disc into the computer’s DVD drive. Click the message “Tap to choose what happens with this disc.” Click Run autorun.exe. Click Install Drivers (button), or Option Drivers (button) to access the Optional driver menu. Figure 4 - 1 - Drivers Installer Screen 1 4 - 2 Driver Installation 5. 6. 7.
Drivers & Utilities Win 8.
Drivers & Utilities Manual Driver Installation Click Browse CD/DVD (button) in the Drivers Installer application and browse to the executable file in the appropriate driver folder. 4 Windows Update After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft). See “Windows Update” on page 4 8 for instructions.
Drivers & Utilities User Account Control If a User Account Control prompt appears as part of the driver installation procedure, click Continue or Allow, and follow the installation procedure as directed. Windows Security Message If you receive a Windows security message as part of the driver installation process. Just click “Install this driver software anyway” or “Install” to continue the installation procedure.
Drivers & Utilities Driver Installation Procedure Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button). 4 Chipset 1. Click 1.Install Chipset Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer. Video (VGA) 1. Click 2.Install VGA Driver > Yes. 2. Click Next > Yes > Next > Next. 3. Click Finish to restart the computer.
Drivers & Utilities Airplane Note: Do not use Update Driver in Device Manager to install the Airplane Mode driver. 1. Click 6.Install Airplane Driver > Yes. 2. Click Next. 3. Click Finish to restart the computer. Hot Key 1. Click 7.Install Hotkey AP > Yes. 2. Click Next > Next. 3. Click Finish > Finish to restart the computer. MEI Driver 1. Click 8.Install MEI Driver > Yes. 2. Click Next > Yes > Next. 3. Click Finish. Audio 1. Click 9.Install Audio Driver > Yes. 2. Click Next. 3.
Drivers & Utilities Windows Update 4 After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc., (all updates will include the latest hotfixes from Microsoft). Optional Drivers See the pages indicated in Table 4 - 1, on page 4 - 3 for the driver installation procedures for any modules included in your purchase option. To enable Windows Update make sure you are connected to the internet: 1. 2. 3. 4. 5. 6. Go to the Control Panel.
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your system ever needs servicing.
BIOS Utilities BIOS Settings Warning 5 Incorrect settings can cause your system to malfunction. To correct mistakes, return to Setup and restore the Previous Values with , or Optimized Defaults with . UEFI Boot & POST When UEFI Boot is enabled, then the prompts to press F2 or F7 will not appear. However you can still press F2 to enter the setup, or F7 to choose the preferred boot device, if you press the key immediately the system boots up.
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized distributor/supplier as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities Setup Menus 5 The Setup menus shown in this section are for reference only. Your computer’s menus will indicate the configuration appropriate for your model and options. Setup Screens The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup.
BIOS Utilities Main Menu Figure 5 - 2 Main Menu System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
BIOS Utilities SATA Port # (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Ports. System/Extended Memory: (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed. 5 MB Series / BIOS Revision / KBC/EC firmware Revision This item contains information on the BIOS version etc., and is not user configurable.
BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu 5 Intel Smart Connect Technology (Advanced Menu) Smart Connect is a technology that makes checks on web applications that are open even when the computer is in sleep mode, and thus allows updates to be made without the need to turn the computer on. The sub-menus here allow you to enable/disable the technology (ISCT Configuration).
BIOS Utilities UEFI Boot 5 When UEFI Boot is enabled, then the prompts to press F2 or F7 will not appear. However you can still press F2 to enter the setup, or F7 to choose the preferred boot device, if you press the key immediately the system boots up. Intel(R) Rapid Start Technology (Advanced Menu) Enable/disable Intel(R) Rapid Start Technology from this menu. The rapid start hibernation mode can resume power within 5 to 6 seconds and can remember your computer's state with zero power.
BIOS Utilities Power On Boot Beep (Advanced Menu) Use this menu item to enable/disable the beep as the computer starts up. Battery Low Alarm Beep (Advanced Menu) Use this menu item to enable/disable the battery low alarm beep.
BIOS Utilities Security Menu Security Menu 5 The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS. Figure 5 - 4 Security Menu Set Supervisor Password (Security Menu) You can set a password for access to the Aptio Setup Utility. This will not affect access to the computer OS (only the Aptio Setup Utility).
BIOS Utilities Note: To clear existing passwords press Enter and type the existing password, then press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance. Set User Password (Security Menu) You can set a password for user mode access to the Aptio Setup Utility. This will not affect access to the computer OS, (only the Setup utility) unless you choose to set a Password on Boot (see below).
BIOS Utilities Secure Boot Control (Security Menu) Secure Boot prevents unauthorized operating systems and software from loading during the startup process. Secure Boot Control is available as a menu option if you have enabled UEFI Boot (see “UEFI Boot (Boot Menu)” on page 5 - 17). Enabling Secure Boot will bring up the Secure Boot Mode menu to enable you to configure Secure Boot as Standard (with a fixed secure boot policy) or Custom (which enables you to make changes to the Key Management database).
BIOS Utilities TPM Configuration (Security Menu) This sub-menu will allow you to enable/disable Trusted Platform Module (TPM) support, and to configure the TPM State. Select TPM Configuration and press Enter to access the sub-menu. Press Enter to access the Security Device Support menu and select Enable to display the full TPM configuration menu (see “Trusted Platform Module” on page 7 - 22 for details).
BIOS Utilities TPM State (Security Menu > Security Device Support Enabled) Select TPM State, press Enter and select Enabled to change the TPM state to enabled. You will then need to press F4 to save the changes and restart the computer. 5 Figure 5 - 6 TPM State (Enabled) As the computer restarts press F2 to enter the BIOS again and go to the TPM Configuration menu.
BIOS Utilities Pending TPM operation (Security Menu > Security Device Support & TPM State Enabled) Select Pending operation, press Enter and select the option you require (if you are initializing TPM you should select Enable Take Ownership). You will then need to press F4 to save the changes and restart the computer. You can now install the TPM driver (see “Trusted Platform Module (TPM) Driver Installation” on page 7 - 25) and then initialize the TPM.
BIOS Utilities Boot Menu Figure 5 - 8 Boot Menu 5 BIOS Screens Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s BIOS. BIOS versions are subject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages. 5 - 16 Boot Menu When you turn the computer on it will look for an operating system (e.g.
BIOS Utilities Boot Option Priorities (Boot Menu) Press Enter to access the menu, use the arrow keys to move up and down the menu, and press Enter to select a device from the Boot Option # list (the selected device will be highlighted in white). UEFI Boot (Boot Menu) Enable/disable UEFI Boot from this menu. The Unified Extensible Firmware Interface (UEFI) specification provides a clean interface between operating systems and platform firmware at boot time.
BIOS Utilities Exit Menu Figure 5 - 9 Exit Menu 5 Click Save Changes and Reset to save all changes made. Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Setup defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session.
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. 4. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Slide the battery out in the direction of the arrow 3 .
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the discs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium. Upgrading the Hard Disk Drive The hard disk drive can be taken out to accommodate other 2.
Upgrading The Computer Removing the Hard Disk 1. 2. 3. 4. Turn off the computer, and turn it over and remove the battery (see page 6 - 3). Remove the screws 1 & 2 . Lift the hard disk bay cover up from point 3 . Remove hard disk bay cover 4 .
Upgrading The Computer 5. 6. 7. Slide the HDD assembly in the direction of arrow 5 . Remove the HDD assembly 6 . Remove the screw(s) 7 - 8 and the adhesive cover 9 . Figure 6 - 3 Hard Disk Assembly Removal 5 6 8 9 6 7 8. 9. Reverse the process to install a new hard disk drive. Replace the hard disk bay cover and screws.
Upgrading The Computer Hard Disk Size Note (Foam Rubber Insert) Note that the hard disks pictured on the preceding pages are 9.5mm(H) hard disk drives. In some cases 7mm(H) hard disk drives will be installed. For more information contact your distributor/supplier, and bear in mind your warranty terms. Figure 6 - 4 Foam Rubber Insert for 7mm(H) HDDs • If you are replacing a 9.5mm(H) HDD with a 7mm(H) HDD then insert the foam rubber insert (as shown above). • If you are replacing a 7mm(H) HDD with a 9.
Upgrading The Computer Upgrading the Optical (CD/DVD) Device The procedure for removing the optical device will depend upon your particular computer model: • See “Upgrading the Optical (CD/DVD) Device for Model A Computers” on page 6 - 8. 6 • See “Upgrading the Optical (CD/DVD) Device for Model B Computers” on page 6 - 11.
Upgrading The Computer Upgrading the Optical (CD/DVD) Device for Model A Computers 1. 2. 3. Turn off the computer, and turn it over and remove the battery (see page 6 - 3). Locate the component bay cover and remove screws 1 - 4 . Remove the component bay cover 5 .
Upgrading The Computer 4. Remove the screw at point 6 , and use a screwdriver to carefully push out the optical device at point 7 . 7 6 Figure 6 - 6 6 Removing the Optical Device Drive (Model A) 7 5. 6. Reverse the process to install the new device. Replace the component bay cover and screws (see page 6 - 8).
Upgrading The Computer Upgrading the Optical (CD/DVD) Device for Model B Computers 1. 2. 3. Turn off the computer, and turn it over and remove the battery (see page 6 - 3) and hard disk drive (see page 6 - 4). Remove the screw at point 1 , and use a screwdriver to carefully push out the optical device at point 2 . Reverse the process to install the new device.
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 204 pin Small Outline Dual In-line (SODIMM) DDR3L type memory modules (see “Memory” on page D - 2 for details of supported module types). 1. 2. 3. Turn off the computer, and turn it over and remove the battery (see page 6 - 3). Locate the component bay cover and remove screws 1 - 4 . Remove the component bay cover 5 .
Upgrading The Computer 4. The memory sockets are visible at point 1 . Figure 6 - 9 RAM Module Location 6 Contact Warning 5. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 7 & 8 ) in Figure 6 - 9. 7 8 Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance.
Upgrading The Computer 6. The RAM module will 9 pop-up, and you can remove it. Single Memory Module Installation If your computer has a single memory module, then insert the module into the Channel 0 (JDIMM1) socket. In this case this is the lower memory socket (the socket closest to the mainboard). Figure 6 - 11 6 RAM Module Removal 7. 8. 9 Pull the latches to release the second module if necessary.
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative.
Modules & Options Important Notice If your purchase option includes both Wireless LAN and 3G modules, then the appropriate antennas will be installed. Note that In order to comply with FCC RF exposure compliance requirements, the antenna must not be co-located or operate in conjunction with any other antenna or transmitter.
Modules & Options PC Camera Module Note that you need to use the Camera app in Windows to take pictures and capture video. Use the Fn + F10 key combination (see “Function/Hot Key Indicators” on page 1 - 13) to toggle power to the PC Camera module. When the PC Camera is in use the LED indicator to the left of the camera will be illuminated in red (see 2 Figure 1 - 2 on page 1 - 7/Figure 1 - 3 on page 1 - 8).
Modules & Options PC Camera Audio Setup If you want to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. 5. 6. 7 Go to the Control Panel. Click Sound (Hardware and Sound) and click Recording (tab). Right-click hold and release Microphone (Realtek High Definition Audio) and make sure the item is not disabled. Double-click Microphone (or select Properties from the right-click menu).
Modules & Options Camera App 1. 2. Run the Camera app from the Start screen by clicking on the Camera app icon . The camera interface will display two buttons on the right side of the screen. Figure 7 - 2 Camera App Buttons Exposure Use the slider to adjust the Exposure level. 3. 4. 5. The upper button is used to record video, and the lower button is used to take still pictures. Right-click on the screen to bring up menu buttons at the bottom of the screen.
Modules & Options Camera Options The Camera Options settings may be accessed as follows: 1. 2. 3. 4. 7 Figure 7 - 4 Camera Options 7 - 6 PC Camera Module Run the Camera app from the Start screen by clicking on the Camera app icon . While the camera app is running access the Charms Bar (e.g. click Use the Windows logo key + D key combination). Click Settings and then click Options.
Modules & Options Taking Pictures/Capturing Video 1. 2. 3. 4. 5. Run the Camera app from the Start screen by clicking on the Camera app icon . Right-click the screen and select the timer if you require a countdown before capture. Click the appropriate icon to take a picture or start video capture (if video capture begins a timer will appear in the bottom corner of the screen). To stop video capture click the main window again (or click the stop icon ).
Modules & Options Camera Roll 1. 2. 3. 4. Run the Camera app from the Start screen by clicking on the Camera app icon . Right-click on the screen to bring up menu buttons at the bottom of the screen. Click Camera Roll. Click the arrows / (on either side of the screen) to browse through the captured photos/video, and back to the Camera app. Editing Photos Figure 7 - 6 1. Clicking on a captured photo will bring up an app bar with a series of buttons. 2. 3.
Modules & Options photo with the edited changes), Update original (which changes the original picture permanently) or Undo any changes. 9. Click the Edit button to bring up a full suite of tools to edit the photo. 10. Click on the menu headings on the left, and then click on the tool on the right to edit the photo as required. Edit Menu Basic Fixes Light Color Effects Figure 7 - 7 Editing Tools 7 11.
Modules & Options Editing Photos 1. Clicking on a captured video will bring up an app bar with a series of buttons. 2. Click Delete to remove any video from the camera roll (you will be asked to click Delete again to confirm the deletion). The Open With butt ton will allow you to select a program with which to run the Video. Clicking Slide Show will create a slide show of photos/video in the camera roll. Click Trim to edit the video.
Modules & Options Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive. Note that the Windows 8.
Modules & Options Wireless Device Operation Aboard Aircraft 7 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the WLAN & Bluetooth module(s) are OFF if you are using the computer aboard aircraft by putting the system in to Airplane Mode (see Table 1 - 3, on page 1 - 13). Wireless LAN Module If you have included an Intel® or 3rd Party WLAN module in your purchase option make sure that the module is on (i.e.
Modules & Options 3rd Party 802.11b/g/n Driver Installation 1. Make sure the module is on and the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install WLAN Driver > Yes. 4. Click Next. 5. Click Finish to restart the computer. 6. The operating system is the default setting for Wireless LAN control in Windows (see page 7 - 14). Intel® WLAN Driver Installation 1.
Modules & Options WLAN Configuration in Windows You can configure a wireless connection using one of the following options, however make sure the Wireless LAN module is turned on (and not in Airplane Mode) before configuration begins. Charms Bar 1. 2. 3. Go to the Charms Bar. Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off). A list of available access points will appear.
Modules & Options 4. 5. 6. 7. 8. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to find other devices or not. When you are connected to the network access point it will display Connected . Select any connected network and click Disconnect to disconnect from a connected access point. 7 Figure 7 - 11 Networks Connected / Disconnect 9.
Modules & Options Desktop Mode 1. 2. 3. 4. 5. 6. 7. Switch to the Windows Desktop (click the app or use the Windows logo key D key combination). Click the wireless icon in the notification area of the taskbar. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to find other devices or not.
Modules & Options Bluetooth & WLAN Combo Module If your purchase option includes the Combination Wireless LAN & Bluetooth module (either Intel® or 3rd Party) then install the driver as instructed overleaf. Make sure that the module is on (i.e. the system is not in Airplane Mode) before installing the driver. Bluetooth Data Transfer Note that the transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported).
Modules & Options High Speed Bluetooth Data Transfer 7 The Combination Wireless LAN & Bluetooth module supports high speed data transfer. However to achieve such transfer speeds, both devices must support high speed data transfer. To obtain high speed data transfer make sure that both the WLAN and Bluetooth modules are powered on. Check your Bluetooth compatible device’s documentation to confirm it supports high speed data transfer. 3rd Party Bluetooth (V4.0) Combo Driver Installation 1.
Modules & Options Bluetooth Configuration in Windows You can configure a Bluetooth connection as below, however make sure the Bluetooth module is on (or the system is not in Airplane Mode) before configuration. Desktop Mode 1. 2. 3. Switch to the Windows Desktop (click the App or use the Windows logo key D key combination). Click the notification area of the taskbar and double-click the Bluetooth icon click and select Show Bluetooth Devices). The Bluetooth item in PC and Devices will appear.
Modules & Options 4. 5. Make sure that Bluetooth is turned on and a list of discovered devices will appear. Double-click the device you want to pair with the computer and click Pair. 6. On first connection the computer will provide you with a pairing code to be entered onto the device. 7. Enter the code into your Bluetooth enabled device and click Yes on the computer to complete the pairing. Select a device and click Remove Device to disconnect from any device.
Modules & Options To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3. 4. Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination). Click the notification area of the taskbar, click the Bluetooth icon and click Open Settings. Click Options, and make sure that Allow Bluetooth devices to find this computer check box (Discovery) has a tick inside it.
Modules & Options Trusted Platform Module The TPM security chip allows you to create and manage digital certificates for user and platform authentication. This type of security is usually administered within large enterprises and organizations, and therefore requires implementation by a system administrator before users can access security features. Individual users can use the TPM as an authentication with the fingerprint reader.
Modules & Options Enabling & Activating TPM 1. 2. 3. 4. 5. 6. Restart the computer. Enter the Aptio Setup Utility pressing F2 during the POST/startup. Use the arrow keys to select the Security menu. Select TPM Configuration and press Enter to access the sub-menu. Press Enter to access the TPM Support menu and select Enable to display the full TPM configuration menu. Select TPM State, press Enter and select Enabled to change the TPM state to enabled.
Modules & Options 8. Select Pending operation, press Enter and select the option you require (if you are initializing TPM you should select Enable Take Ownership and press Enter). You will then need to press F4 to save the changes and restart the computer. 9. You can now install the TPM driver (see “Trusted Platform Module (TPM) Driver Installation” on page 7 - 25) and then initialize the TPM.
Modules & Options Trusted Platform Module (TPM) Driver Installation 1. Make sure you have enabled and activated the TPM in the BIOS before installing the driver. 2. Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 3. Click Option Drivers (button). 4. Click 3.Install TPM Driver > Yes. 5. Click Next. 6. Click the button to accept the license and click Next. 7. Click Next > Next > Install. 8. Click Finish > Yes to restart the computer.
Modules & Options Initializing TPM 1. 2. 3. 4. 5. 7 Switch to the Desktop app and click the TPM icon right-click the icon in the notification area of the taskbar, and select Security Platform Initialization (or click the Security Platform State taskbar bubble). Click User Settings (tab) and click Yes, or right-click the icon in the notification area of the taskbar, and select Security Platform Initialization (or click the Security Platform State taskbar bubble).
Modules & Options 6. 7. Choose the Security Platform Features you want to use by clicking the appropriate tickbox. Enter a Basic User Password (and re-type to confirm it) and click Next. Help Right-click the icon in the notification area of the taskbar to bring up the menu to select Help or How to use the Security Platform Features. 7 8. 9. 10. 11. 12. Click Next to confirm the settings. The computer will then initialize the settings. Click Finish.
Modules & Options Menus Note that not all the menus pictured here will be available for access. The menu items that appear will be dependent on your configuration settings etc. (see the Help file for full details). Infineon Security Platform Settings Tool The Infineon Security Platform Settings Tool allows you to manage and check the TPM state, manage your password information, and to backup and restore the TPM data.
Modules & Options User Settings This page allows the settings to be configured for the currently logged in Infineon Security Platform user including the ability to change the password, configure secure e-mail, file and folder encryption and Enhanced Authentication. You can also import or delete certificates protected by the security platform.
Modules & Options Backup Here you can configure backup and restore operations. Backup files contain the computer identification and user identification information which is used to match the machine name and user name with the current machine and user during restoration.
Modules & Options Migration The Migration tab is used to help securely transfer keys and certificates from one platform to another.
Modules & Options Password Reset Use Password Reset to reset basic user passwords when required.
Modules & Options BitLocker BitLocker Drive Encryption can be used in conjunction with the TPM to encrypt data on the disk and is done via the Microsoft BitLocker Control Panel Applet. Click Configure and select a drive to be encrypted and then follow the Wizard to begin the encryption process.
Modules & Options Access the Microsoft BitLocker Drive Encryption control panel applet from the Windows control panel (System and Security).
Modules & Options Advanced Configure all the Security Platform owner and policy settings from the Advanced tab. The settings that can be changed are for the local computer only.
Modules & Options Intel® Rapid Storage Technology Install the Intel® Rapid Storage Technology to support your AHCI mode SATA drive. 7 IRST Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 4.Install IRST Driver > Yes. 4. Click Next. 5. Click in the tickbox to accept the license and click Next. 6. Click Next > Next > Next. 7. Click Finish to restart the computer. 8.
Modules & Options Intel® Rapid Start Technology Driver Intel(R) Rapid Start Technology can resume power from Hibernation within 5 to 6 seconds and can remember your computer's previous state with zero power. System Requirements to support Intel® Rapid Start Technology: • Rapid Start Technology should be enabled in the BIOS (see ““Intel(R) Rapid Start Technology (Advanced Menu)” on page 5 - 8). • Intel Rapid Storage Technology software installed (see “Intel® Rapid Storage Technology” on page 7 - 36).
Modules & Options Intel® Rapid Start Technology Configuration 1. 2. 3. 7 Enable/disable Intel(R) Rapid Start Technology from the BIOS (see “Intel(R) Rapid Start Technology (Advanced Menu)” on page 5 - 8). Go the Windows control panel and double-click Administrative Tools (System and Security)> Computer Management > Storage > Disk Management Right-click the SSD and select Shrink Volume from the menu.
Modules & Options 4. Enter the figure, which should be equal to amount of system memory (RAM) in your computer, in “Enter the amount of space to shrink in MB”. Figure 7 - 30 Shrink Volume Size 7 5. Click Shrink (any unallocated file space may be formatted for storage use). Memory Size (Amount of Space to Shrink) The figure entered in the “Enter the amount of space to shrink in MB” field above should be equal to the amount of system memory in your computer.
Modules & Options 6. Run the Desktop app and right-click the lower left hot corner (or use the Windows Logo Key + X key combination) and select Command Prompt (Admin). 7. 8. Type “DISKPART”. At the DISKPART command type “list disk”.
Modules & Options 9. Type “select disk #” (# is disk number where you want to create the store partition, so refer to the results obtained from "list disk" for exact disk number). 10. The message “Disk # is now the selected disk.” will appear. Figure 7 - 33 Diskpart - Select Disk # 7 11. Type “create partition primary”. 12. A “DiskPart succeeded in creating the specified partition.” message should appear.
Modules & Options 13. Type “detail disk”. Figure 7 - 35 Diskpart - Detail Disk 14. Type “select Volume #” (# is volume of your storage partition so refer to results obtained from "detail disk" for the exact volume number). 15. The message “Volume # is now the selected volume.” will appear.
Modules & Options 16. Type the following, depending on the format of the SSD. • For MBR formatted SSDs: “set id=84 override” (the id must be set to 84). • For GPT formatted SSDs: “set id=D3BFE2DE-3DAF-11DF-BA40-E3A556D89593”. Figure 7 - 37 Diskpart - Set id= 7 17. The message “DiskPart successfully set the partition ID.” will appear. 18. Close the CMD window.
Modules & Options 19. Go the Windows control panel and double-click Administrative Tools (System and Security)> Computer Management > Storage > Disk Management. 20. The disk partition should read Healthy Hibernation Partition. Figure 7 - 38 Computer Management (Healthy Hibernation Partition) 7 Healthy (Hibernation Partition) 21. Restart the computer. 22. Install the driver (see below). Intel® Rapid Start Technology Driver Installation 1.
Modules & Options Intel® Smart Connect Technology Intel® Smart Connect Technology periodically, and briefly, wakes the computer from Sleep mode in order to update information for certain applications (e.g. to get mail from Microsoft Outlook) as required.
Modules & Options Wireless Device Operation Aboard Aircraft 7 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the WLAN & Bluetooth module(s) are OFF if you are using the computer aboard aircraft by putting the system in to Airplane Mode (see Table 1 - 4, on page 1 - 11). Intel® Smart Connect Technology Configuration 1. 2. 3. 4. 5. Access the Intel(R) Smart Connect Technology application from the Apps menu.
Modules & Options 6. 7. Click Customize Schedule to customize the update frequency, and the hours and days when the updates will occur. Bear in mind that the more often you set the system to update, the more power is consumed, and this may be a consideration if the system is battery powered. iSCT & System Power Note that Intel Smart Connect will turn off when it detects a low battery level, and will not run if the system is Shut Down or is in Hibernate mode.
Modules & Options 8. Click the Help icon Intel WLAN Modules 7 If your purchase option includes an Intel WLAN module, (with Intel’s PROSet Wireless Connection Utility installed), Intel® Smart Connect Technology will search for WiFi networks around you that you have previously accessed. If no known WiFi networks are found, your computer will not update again until it recognizes a known WiFi network. Figure 7 - 41 iSCT Help 7 - 48 Intel® Smart Connect Technology and select Help to access the menu.
Modules & Options Remote Wake Remote Wake allows you to wake the computer remotely from another device such as a phone, tablet or another PC. This will allow you to access files on the computer. A link to a list of applications and usage is supplied if you click Learn More and the link provided. An application must support this feature and you will need to register any devices.
Modules & Options Wireless Device Operation Aboard Aircraft 7 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the WLAN & Bluetooth module(s) are OFF if you are using the computer aboard aircraft by putting the system in to Airplane Mode (see Table 1 - 3, on page 1 - 13).
Modules & Options 3G Module USIM Card Installation Follow the instructions below to install the USIM card (which will be provided by your service provider). 1. 2. 3. 4. 5. Turn off the computer, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Remove the battery 3 . Insert the USIM card 4 (at the rear of the battery compartment) as illustrated below until it clicks fully into position, and replace the battery.
Modules & Options 3G Configuration in Windows You can configure a 3G connection as below, however make sure the system is not in Airplane Mode before configuration begins. Charms Bar 1. 2. \ 3. 7 Figure 7 - 43 Networks Mobile Broadband 7 - 52 3G Module Go to the Charms Bar. Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off). A list of available access points will appear under Mobile Broadband.
Modules & Options 4. 5. Any 3G service provider (connection information is usually stored on the USIM card) will appear under Mobile Broadband. Double-click any connection icon under Mobile Broadband (or click and then click Connect). Figure 7 - 44 Mobile Broadband (Connect) 7 6. 7. The system will connect to your network. A Connected will appear alongside the 3G connection (click the connection to view the timer which indicates your connected time for the current session).
Modules & Options Wireless Device Operation Aboard Aircraft 8. 9. You can then access the internet, download e-mail etc. as per any internet connection. To disconnect you can select the connection and click Disconnect . The use of any portable electronic transmission devices aboard aircraft is usually prohibited. 7 Make sure the system is in Airplane Mode if you are using the computer aboard aircraft. Figure 7 - 45 Mobile Broadband (Disconnect) 7 - 54 3G Module 10.
Modules & Options EM820W 3G Module PIN Code & Power-Saving Note that there may be some issues when a PIN Code is set for the EM820W 3G module (if you are unsure of your module version contact your distributor/supplier) in Windows, if Mobile Broadband has been turned off, and the system has resumed from a power-saving state. To prevent any issues it is recommended that you simply do not enable a PIN for the EM820W 3G module.
Modules & Options 7 3. 4. 5. 6. 7. Click Network. Click the broadband connection under Mobile Broadband. Scroll down to Security and click Remove PIN. Enter the current PIN number and click OK. It is recommended that you do not Enable a PIN for the EM820W 3G module. 8. Click Security (tab) and click Disable PIN.
Modules & Options Wireless Display Wireless Display uses your Wireless LAN module/WLAN Bluetooth Combo module (you need to make sure that your video adapter/display device is compatible with your particular WLAN/Combo module) in conjunction with a compatible video adapter/display device (purchased separately) to allow you to display the contents of the notebook display on another display (e.g. HDTV), without the need to have cables stretching across a room.
Modules & Options Wireless Display Configuration 1. 2. 3. 4. 7 Figure 7 - 49 Add a Wireless Display 7 - 58 Wireless Display Note that no driver or application is required for wireless display in Windows 8.1. Go the Charms Bar, select Devices. Click Project. Click Add a wireless display.
Modules & Options 5. The system will then search for compatible display devices (this may take up to 60 seconds so allow time for this to complete). Figure 7 - 50 Searching For Devices 7 6. 7. 8. Double-click any detected display device in the list. You may then need to input a pin number for the device to which you are connecting. Click Next.
Modules & Options 9. The display will then connect (for specific settings for your display see the documentation supplied with your compatible adapter/display for full details). 10. To disconnect from the display you can select it in PC and Devices > Devices and click Remove Device > Yes; or go to the Project menu (Charms Bar > Devices) and click Disconnect.
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “LED Indicators” on page 1 - 9) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED power indicator blinking orange. , is Low Battery. Plug in the DC power source.
Troubleshooting Problem The computer feels too hot. Possible Cause - Solution Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 18). Make sure you’re using the correct adapter.
Troubleshooting Problem Possible Cause - Solution You forget the boot password. If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Problem Possible Cause - Solution I am sliding my finger up and down on the right side of the Touchpad to scroll a Window and the Touchpad does not respond. There are different Touchpad versions available on this computer, and this version requires tapping/holding to scroll. Either tap repeatedly, or hold the finger down, at the top or bottom right of the Touchpad (depending on the scrolling direction required) to scroll the window.
Troubleshooting Problem Possible Cause - Solution The Wireless LAN/Bluetooth modules cannot be detected. The modules are off as the computer is in Airplane Mode. Check the LED indicator to see if it is in Airplane Mode (see “LED Indicators” on page 1 - 9). Use the Fn + F11 key combination to toggle Airplane Mode on/off (see Table 1 - 3, on page 1 - 13). The PC Camera module cannot be detected. The module is off.
Troubleshooting Problem Possible Cause - Solution I have used Update Driver in Device Manager (Unknown device > Other Devices) to try and install the Airplane Mode driver. Windows encountered a problem in attempting to update the driver, and a yellow exclamation mark appears in Device Manager against the Unknown device. It is very important that the drivers are installed in the order indicated in Chapter 4 (which is the numbered installation order on the Device Drivers & Utilities + User’s Manual disc).
Troubleshooting Problem Possible Cause - Solution I have connected a Bluetooth Mouse but it loses the Bluetooth connection and no longer responds after a short period of inactivity. This is an issue with some mouse models and the Intel Wireless 7260 WLAN and Bluetooth combo module series. To resolve this issue do the following: 1. 2. 3. 4. 5. 6. Go to the Device Manager control panel in Windows. Click the arrow alongside Bluetooth to expand the menu if required.
Troubleshooting Problem Possible Cause - Solution When using a Bluetooth headset the audio appears to be mono and not stereo. This is a common issue with Bluetooth headsets. To resolve this issue do the following (you will need to repeat this procedure after every boot up, restart, or when the system resumes from hibernation): 1. 2. 3. Go to the Devices & Printers control panel in Windows. Double-click the Bluetooth headset. Click Connect to complete the stereo connection. OR 1. 2. 3.
Troubleshooting EM820W 3G Module PIN Code & Power-Saving Note that there may be some issues when a PIN Code is set for the EM820W 3G module (if you are unsure of your module version contact your distributor/supplier) in Windows, if Mobile Broadband has been turned off, and the system has resumed from a power-saving state. To prevent any issues it is recommended that you simply do not enable a PIN for the EM820W 3G module. The following provides instructions for disabling the PIN code.
Troubleshooting 3. 4. 5. 6. 7. Click Network. Click the broadband connection under Mobile Broadband. Scroll down to Security and click Remove PIN. Enter the current PIN number and click OK. It is recommended that you do not Enable a PIN for the EM820W 3G module.
Troubleshooting Resolving the “Insert a SIM” issue with the 3G Module (Windows 8.1) 1. 2. 3. 4. 5. 6. 7. 8. 9. If a PIN was set for the EM820W 3G module, you have then switched Mobile broadband off (or put the system in Airplane Mode) in Networks, and the system has just resumed from a power-saving state the following error may occur. On resuming from the power-saving state the standard procedure would be to go to Networks in the Charms Bar and turn on Mobile broadband. Go to the Charms Bar.
Troubleshooting 8 8 - 18
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer. External Monitor (VGA) Port This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD.
Interface (Ports & Jacks) Item Description Microphone-In Jack Plug an external microphone in to this jack to record on your computer. RJ-45 LAN Jack This port supports LAN (Network) functions. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port. Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. USB 2.0/1.1 Ports These USB 2.0 compatible ports (USB 2.0 is fully USB 1.
Interface (Ports & Jacks) A A - 4
Control Center Appendix B: Control Center Overview The following chapter will give a quick description of the functions of the Control Center. The Control Center gives quick access to frequently used controls, power management features and enables you to quickly turn modules on/off. Click the Control Center icons to toggle the appropriate function, or hold the mouse button down and move the slider where applicable. Certain functions will automatically be adjusted when a power mode is selected.
Control Center Power Modes You can set a Power Mode by clicking the appropriate icon at the top of the Control Center. Each power mode will affect screen brightness, Touchpad and PC camera power etc. You can click a Control Center icon to set an overall power mode and then click individual icons in the Control Center to power on/off the Touchpad and PC camera.
Control Center Power Status The Power Status icon will show whether you are currently powered by the battery, or by the AC/DC adapter plugged in to a working power outlet. The power status bar will show the current battery charge state. Brightness The Brightness icon will show the current screen brightness level. You can use the slider to adjust the screen brightness or the Fn + F8/F9 key combinations, or use the Fn+ F2 key combination to turn off the LED backlight (press any key to turn it on again).
Control Center Sleep Click the Sleep button to bring up the Hibernate or Sleep buttons, and click either button to have the computer enter the appropriate power-saving mode (see “Power-Saving States” on page 3 - 7). Display Switch Click the Display Switch button to access the menu (or use the priate attached display mode (see page C - 19). + P key combination) and select the appro- Time Zone Clicking the Time Zone button will access the Date and Time Windows control panel.
Video Driver Controls Appendix C: Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 31. Video Driver Installation Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. 1. Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button). 2. Click 2.Install VGA Driver > Yes. 3. Click Next > Yes > Next > Next. 4. Click Finish to restart the computer.
Video Driver Controls Intel® HD Graphics Control Panel Advanced video configuration options are provided by the Intel® HD Control Panel. To access the control panel see below and overleaf: 1. Click the Intel® HD Graphics Control Panel icon in the Apps screen.
Video Driver Controls OR 2. Right-click the Desktop and select Graphics Properties from the menu. OR 3. 4. 5. Click Advanced settings in the Screen Resolution control panel in Windows. Click the Intel(R) HD Graphics Control Panel tab and click Graphics Properties (button). Double-click the Intel(R) HD Graphics control panel in the Windows Control Panel.
Video Driver Controls You may make changes to any of the graphics properties by clicking the appropriate menu panel and adjusting the settings from the menus.
Video Driver Controls Sub-Menus Some of the menu panels will also have sub-menus (in the top left corner of the menu alongside the icon ) to display further configuration options.
Video Driver Controls Multiple Display Display Click either Display Settings or Color to make display adjustments, including configuration for any attached external displays. At least one other display must be attached in order to view multiple display selection options.
Video Driver Controls Click the Display menu at the top of the screen to display the sub-menus. The Multiple Displays menu allows you to configure the display mode of any attached displays (see “Attaching Other Displays” on page C - 16). Multiple Display At least one other display must be attached in order to view multiple display selection options.
Video Driver Controls The Audio sub-menu allows you to configure the capability mode of any attached displays if applicable (i.e. the attached display supports audio).
Video Driver Controls 3D This menu allows you to choose how 3D images are displayed. Quality displays the most detail, Balanced provides better computer performance with good quality and Custom allows you to configure the Anisotropic Filtering and Vertical Sync and features to your preferences. Click Apply to save changes.
Video Driver Controls Options Options allows you to Customize Hot Keys (for opening the application, rotating the display, scaling etc.,) to your preferences. Click Apply to save changes.
Video Driver Controls Click the Options menu at the top of the screen to display the sub-menus. The Information Center provides details on System Information, the Built-In Display and any attached displays. Preferences Go to the Preferences sub-menu in Options to configure the preferences for the Intel® HD Graphics Control Panel. Make sure you turn Tray Icon On to display the Intel® HD Graphics Control Panel icon in the notification area of the taskbar (as below).
Video Driver Controls Video The Video Profiles menu allows you to brighten or darken movies, or to switch to vivid colors. The Preview image will display a sample image using the current settings. You can Save Profile and name the Profile to recall the settings at any time. Click Apply to save changes (select Color Enhancement, Image Enhancement or Image Scaling from the menu).
Video Driver Controls Click the Video menu at the top of the screen to display the sub-menus.The Image Enhancement menu allows you to adjust the Sharpness, Skin Tone Enhancement, Noise Reduction etc.Click Apply to save changes.
Video Driver Controls Turn Image Scaling on, and use the sliders to adjust the scaling.
Video Driver Controls Display Devices & Options Note that you can use external displays connected to the HDMI-Out port and/or external monitor port. See your display device manual to see which formats are supported. Attaching Displays When you first attach an external display you may find that the desktop does not occupy the full screen area. Use either the display’s auto adjust/configure controls, or the Intel(R) HD Graphics Control Panel to configure the full screen display.
Video Driver Controls Multiple Display At least one other display must be attached in order to view Multiple Display selection options. Attaching Other Displays To Clone Displays: 1. 2. 3. 4. 5. Attach your external display to the HDMI-Out port/external monitor port, and turn it on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Multiple Displays (sub-menu). Click Clone from the Select Multiple Display Mode menu. Click Apply, and OK to confirm the settings change.
Video Driver Controls To Enable Extended Mode: 1. 2. 3. 4. Attach your external display to the HDMI-Out port/external monitor port, and turn it on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Multiple Displays (sub-menu). Click Extended from the Select Multiple Display Mode menu. Click Apply, and OK to confirm the settings change. Click the appropriate monitor icon and drag it to match the physical arrangement you wish to use (e.g.
Video Driver Controls To Enable Collage Mode: 1. Collage Mode 2. Collage mode is used to combine a number of displays into a single unified higher resolution for larger screen sizes,. 3. 4. 5. 6. Attach your external displays to the external monitor port and HDMI-Out port, and turn them on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Multiple Displays (sub-menu). Click Collage from the Select Multiple Display Mode menu. Click Enable Collage and click On.
Video Driver Controls Attaching Other Displays - Devices (Charms Bar) You can configure attached displays from Devices (in the Charms Bar). 1. 2. 3. 4. Attach your external display to the HDMI-Out port/external monitor port, and turn it on. Go the Charms Bar, select Devices. Click Project (you may need to click Second Screen). Click on any one of the options from the menu to select PC screen only, Duplicate, Extend or Second screen only.
Video Driver Controls Configuring an External Display In Windows 1. 2. 3. 4. Attach your external display to the HDMI-Out port/external monitor port, and turn it on. Go to the Screen resolution control panel (see page 1 - 35) in the Desktop app. Click the Detect button. The computer will then detect any attached displays.
Video Driver Controls 5. You can configure the displays from the Multiple Displays menu. Figure C - 19 Screen Resolution Multiple Display Options • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) • Extend these displays - Treats both connected displays as separate devices • Show desktop only on 1/2 - Only one of your displays is used.
Video Driver Controls Volume Adjustment The sound volume level can be set using the volume control in the Settings menu in the Charms Bar. HDMI Audio Configuration HDMI (High-Definition Multimedia Interface) carries both audio and video signals. In some cases it will be necessary to go to the Sound control panel and manually configure the HDMI audio output as per the instructions below. 1. 2. 3. 4. C Go to the Control Panel.
Video Driver Controls 5. 6. Adjust the HDMI settings from the control panel tabs. Click/tap OK to close the Sound control panel.
Video Driver Controls Other Applications If you are using a third party application to play DVDs etc. from any attached DVD device, you will need to consult the application’s documentation to see the appropriate audio configuration (the application must support digital to analog translation). HDMI Notes • Connect a device with HDMI support to the HDMI-Out port BEFORE attempting to play audio/video sources through the device.
Specifications Appendix D: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your distributor/supplier for details.
Specifications Processors Memory Storage Intel® Core i5-4200U (1.60GHz) 3M L3 Cache, 22nm (22 Nanometer), DDR3L-1600MHz, TDP 15W Dual Channel DDR3L One Changeable 9.5mm(h) Super Multi/ Blu-ray Combo Optical Device Drive with SATA Interface (Factory Option) Intel® Core i3-4005U (1.70GHz) 3M L3 Cache, 22nm (22 Nanometer), DDR3L-1600MHz, TDP 15W Intel® Pentium® 3556U (1.70GHz) 2M L3 Cache, 22nm (22 Nanometer), DDR3L-1600MHz, TDP 15W Intel® Celeron® 2955U (1.
Specifications Interface Slot Model A: One USB 2.0 Port Two Mini-Card Slots: Model B: Two USB 2.0 Ports All Models: Two USB 3.0 Ports One External Monitor Port One HDMI-Out (High-Definition Multimedia Interface) Port (with HDCP) One Headphone-Out Jack One Microphone-In Jack One RJ-45 LAN Jack One DC-In Jack Card Reader Embedded Multi-In-1 Card Reader - MMC/ RS MMC - SD/ Mini SD / SDHC/ SDXC - MS/ MS Pro/ MS Duo Note: Some of these cards require PC adapters that are usually supplied with the cards.
Specifications Security Environmental Spec Security (Kensington® Type) Lock Slot BIOS Password Trusted Platform Module 1.2 (Factory Option) Temperature Operating: Non-Operating: Relative Humidity Operating: Non-Operating: Features Painted Style (For some Model designs) IMR (Injected Molded Resin) LCD Back Covers (For some Model designs) Intel® Anti-Theft Technology Intel® Rapid Start Technology Operating System Windows® 8.
