V09.1.
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Warning Use only shielded cables to connect I/O devices to this equipment.
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: 1. 2. 3. 4. 5. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer to any shock or vibration. 2. Do not place it on an unstable surface. Do not place anything heavy on the computer. Keep it dry, and don’t overheat it.
Preface 3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. 4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted. Do not turn off the power until you properly shut down all programs. 5.
Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company. • The power adapter may have either a 2-prong or a 3-prong grounded plug.
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply.
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: 1. 2. 3. 4. 5. 6. 7. 8. Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain: • Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • • • • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. Position the display directly in front of you at a comfortable viewing distance. Adjust the display-viewing angle to find the best position.
Preface XIV
Preface Contents Notice .................................................................................I FCC Statement .............................................................II FCC RF Radiation Exposure Statement: ................... III Instructions for Care and Operation ........................... V Power Safety .............................................................VII Battery Precautions ................................................. VIII Cleaning .....................................
Preface TouchPad and Buttons/Mouse .......................................2-8 Audio Features .............................................................2-10 Adding a Printer ...........................................................2-11 USB Printer ..............................................................2-11 Parallel Printer ..........................................................2-11 Power Management Overview ........................................................................
Preface BIOS Utilities Overview ........................................................................5-1 The Power-On Self Test (POST) ...................................5-2 Failing the POST .........................................................5-3 Fatal Errors .................................................................5-3 Non-Fatal Errors .........................................................5-3 The Setup Program ........................................................5-4 Entering Setup ...
Preface HSPA Modem Interface ............................................7-24 HSPA Modem Interface Installation ........................7-24 HSPA Modem Interface ...........................................7-25 Adding a Profile .......................................................7-27 Contacts ....................................................................7-29 Messages ...................................................................7-30 Settings .....................................................
Preface Power Management ...................................................... C-3 Power ............................................................................ C-3 Security ......................................................................... C-3 Operating System .......................................................... C-3 Environmental Spec ...................................................... C-3 Dimensions & Weight .................................................. C-3 Optional ............
Preface XX
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: • Chapter 2 • Chapter 3 • Chapter 4 • Chapter 5 • Chapter 6 • Chapter 7 • Chapter 8 • Appendix A • Appendix B • Appendix C • Appendix D A guide to using some of the main features of the computer e.g.
1 Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on page 6 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a of interest to you.
Quick Start Guide Not Included Operating Systems (e.g. Windows Vista/Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals. Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1.
1 Quick Start Guide System Startup 1. 2. 3. 4. 5. Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
Quick Start Guide Operating System Setup If you are installing new system software, or are re-configuring your computer for a different system, make sure you configure the appropriate OS setting in the BIOS before installing a new operating system (Note: If you have installed the Windows Vista operating system with AHCI mode enabled, DO NOT disable AHCI mode or you will need to reinstall the Windows Vista OS). 1. Start-up the computer and press to enter the BIOS. 2.
1 Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the following operating systems are supported.
Quick Start Guide Model Differences This notebook series includes two different model types. The models differ as indicated in the table below however all other features, modules and specifications are identical (see Appendix D). Feature Model A Model B Display Type Supported 14.1" WXGA (1280 * 800) TFT LCD 15.
1 Quick Start Guide Figure 1 - 3 LCD Panel Open (Model A) 1. 2. 3. 4. 5. 6. 7. 8. 9. System Map: LCD Panel Open - Model A 1 Wireless Device Operation Aboard Aircraft Built-In PC Camera (Optional) LCD Speakers Power Button Hot Key Buttons Keyboard Built-In Microphone Touchpad & Buttons LED Indicators 2 The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
Quick Start Guide System Map: LCD Panel Open - Model B 1 Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 2 3 3 5 4 6 Figure 1 - 4 LCD Panel Open (Model B) Use the key combinations to toggle power to the 3.
1 Quick Start Guide LED Indicators Icon The LED indicators on the computer display helpful information about the current status of the computer.
Quick Start Guide Hot Key Buttons These buttons give instant access to the default Internet browser and e-mail program, and allow you to toggle the Silent Mode on/off with one quick button press. Hot Key Function Activate the Default E-Mail Browser Activate the Default Internet Program Toggle *Silent Mode (for power saving) Table 1 - 5 - Hot Key Buttons *When enabled, Silent Mode will reduce fan noise and save power consumption. Note this may reduce computer performance.
1 Quick Start Guide Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/ hot-keys unique to the system’s regular keyboard may not work. Keyboard - Model A The keyboard has a numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly.
Quick Start Guide Keyboard - Model B The keyboard has a numerical keypad on the right for easy numeric data input, and features function keys to allow you to change operational features instantly. See Table 1 - 6, on page 1 - 14 for full function key combination details. Function Keys NumLk & ScrLk Keys Play/Pause Key Numerical Keypad 3.5G Module Power Toggle Key Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard.
1 Quick Start Guide Function/Hot Key Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility is installed. Fn Keys Function Fn Keys Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F5/F6 Fn + _ Fn + F1 Fn + F2 Fn + F3 Function Volume Decrease/Increase 3.
Quick Start Guide System Map: Front & Left Views Figure 1 - 7 Front & Left Views 1 2 1. 2. 3. 4 3 7 5 6 6 4. 5. 8 6. 7. 7-in-1 Card Reader 8. LED Indicators DC-In Jack External Monitor Port RJ-45 LAN Jack Vent/Fan Intake/ Outlet 2 * USB 2.
1 Quick Start Guide Figure 1 - 8 Right & Rear Views 1. 2. 3. 4. 5. 6. 7. S/PDIF-Out Jack Microphone-In Jack Headphone-Out Jack USB 2.0 Port Optical Device Drive Bay (for CD/DVD Device) Security Lock Slot Battery Disk Eject Warning Don’t try to eject a CD/ DVD while the system is accessing it. This may cause the system to “crash”. Stop the disk first then eject it, or press the stop button twice.
Quick Start Guide System Map: Bottom View - Model A Figure 1 - 9 Bottom View (Model A) 1 2 Battery Information Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 10 for full instructions. 1. 2. 3. 4 3 4. 5. 5 4 Battery Bluetooth Module Cover RAM & CPU Bay Cover Vent/Fan Intake/ Outlet Hard Disk Bay Cover Note: the 3.
1 Quick Start Guide Figure 1 - 10 Bottom View (Model B) 1. 2. 3. 4. Battery RAM & CPU Bay Cover Vent/Fan Intake/ Outlet Hard Disk Bay Cover Note: the 3.75G/HSPA USIM Card is located under the RAM & CPU Bay Cover. System Map: Bottom View - Model B 1 Battery Information Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Quick Start Guide Windows Vista Start Menu & Control Panel Most of the control panels, utilities and programs within Windows Vista (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
1 Quick Start Guide Video Features You can configure display options, from the Display Settings control panel in Windows as long as the appropriate video driver is installed. For more detailed video information see “ATI Video Driver Controls” on page B - 1. To access Display Settings in Windows: To access Display Settings in Windows: 1. Click Start, and click Control Panel (or point to Settings and click Control Panel). 2.
Quick Start Guide Display Devices & Options Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display as your display device. 4 1 5 2 3 Video Card Options Note that card types, specifications and drivers are subject to continual updates and changes. Check with your service center for the latest details on video cards supported.
1 Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 17) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
Features & Components Chapter 2: Features & Components 2 Overview Read this chapter to learn more about the following main features and components of the computer: • • • • • • • Hard Disk Drive Optical (CD/DVD) Device 7-in-1 Card Reader ExpressCard Slot TouchPad and Buttons/Mouse Audio Features Adding a Printer Overview 2 - 1
Features & Components 2 Power Safety Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer. Figure 2 - 1 Hard Disk Location 2 - 2 Hard Disk Drive Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 2). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 13).
Features & Components 2 Handling CDs or DVDs CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole. Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Features & Components DVD Regional Codes 2 To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - 16. .
Features & Components 2 Card Reader Cover Make sure you keep the rubber cover provided in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader. 7-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the Card Reader driver (see “CardReader” on page 4 - 6).
Features & Components ExpressCard Slot The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards). Make sure you install the Card Reader driver (see “CardReader” on page 4 - 6). ExpressCard/54 is used for applications which require a larger interface slot, e.g. CompactFlash card reader. The number denotes the card width; 54mm for the Express Card/54 and 34mm for the ExpressCard/34.
Features & Components 2 Mouse Driver If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details. TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.
Features & Components Audio Features You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/ control panel (right-click the taskbar icon bring up an audio menu). The volume may also be adjusted by means of the Fn + F5/F6 key combination. Sound Volume Adjustment The sound volume level is set using the volume control within Windows (and the volume function keys on the computer).
Features & Components 2 Parallel Printer After setting up the printer attach the parallel cable to the printer. Connect the printer’s parallel cable to the Parallel to USB converter, and then plug the converter into the USB port. Turn ON the printer, then turn ON the computer. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions. Adding a Printer The most commonly used peripheral is a printer.
Power Management Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.
Power Management 3 The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. Silent Mode Use the key to toggle Silent Mode to reduce fan noise and save power consumption. Note this may reduce computer performance. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-in jack on the left of the computer.
Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Sleep/Hibernate hotkey button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will force the computer to shut down). Use Power Options (Hardware and Sound menu) control panel in Windows Vista to configure this feature.
Power Management 3 Resuming Operation See Table 3 - 1, on page 3 - 9 for information on how to resume from a power-saving state. Password It is recommended that you enable a password on system resume in order to protect your data. Figure 3 - 1 Power Plan Advanced Settings 3 - 4 Power Plans Power Plans The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
Power Management Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose High performance for maximum performance when the computer is powered from an AC power source.
Power Management 3 Power Button The Power Button in the Start Menu (in Classic View use the Shut Down button ) can be used to send the computer into a powersaving state. Sleep Mode & Mobile PC Battery A mobile PC in Sleep uses very little battery power. After an extended period of time the computer will save any open documents and applications to hard disk. Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off.
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hibernate will also return you to where you last left off within seconds.
Power Management 3 Password Protection Configuring the Power Buttons The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. It is recommended that you enable a password on wake up in order to protect your data. However you can disable this setting from the Power Options menu by clicking Require a password on wakeup in the left menu, and selecting the options (click Change settings that are currently unavailable).
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo). Power Status Icon To Resume Color Power Off Off Press the Power Button Sleep Blinking Green Press the Power Button Closing the Lid If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up.
Power Management 3 Low Battery Warning When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted. Battery Information Please follow these simple guidelines to get the best use out of your battery. Battery Power Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g.
Power Management Conserving Battery Power • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. • Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter. • Reduce the amount of time before the display is turned off. • Close wireless, Bluetooth, modem or communication applications when they are not being used.
Power Management Battery Life 3 Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason see “Removing the Battery” on page 6 - 3. New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page 3 - 14 for instructions on how to do this).
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Caution Danger of explosion if battery is incorrectly replaced. Damaged Battery Warning Should you notice any physical defects (e.g.
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. 3 1. 2. 3. Save and close all files and applications. Create a power plan for discharging the battery and set all the options to Never.
Power Management 4. 5. Scroll down to Battery and click + to expand the battery options.
Power Management 3 How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Drivers & Utilities Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Drivers & Utilities Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers/Option Drivers (button). 2. 4 If you wish to install the drivers manually see overleaf for the driver path information. 3. Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below.
Drivers & Utilities Driver - Windows Vista with Service Pack 1 Page Video Page 4 - 5 Audio Page 4 - 5 LAN Page 4 - 6 TouchPad Page 4 - 6 CardReader Page 4 - 6 Hot Key Page 4 - 6 PC Camera Module Page 7 - 12 Wireless LAN Module Page 7 - 6 3.75G/HSPA Module Page 7 - 19 Table 4 - 1 - Driver Installation Manual Driver Installation Click Browse CD (button) in the Drivers Installer application and browse to the executable file in the appropriate driver folder.
Drivers & Utilities 4 Updating/Reinstalling Individual Drivers User Account Control (Win Vista) If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Programs > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer).
Drivers & Utilities New Hardware Found Driver Installation Procedure If you see the message “New Hardware Found” during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure. Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button).
Drivers & Utilities 4 LAN 1. Click 3.Install LAN Driver > Yes. 2. Click Install. 3. Click Finish. 4. The network settings can now be configured. TouchPad 1. Click 4.Install Touchpad Driver > Yes. 2. Click Next. 3. Click Finish > Restart Now to restart the computer. Windows Update After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all updates will include the latest hotfixes from Microsoft).
Drivers & Utilities Optional Drivers Bluetooth Module See the pages indicated for the driver installation procedures for any modules included in your purchase option. Note: The operating system is the default setting for Bluetooth control in Windows Vista, and does not require a driver. See “Bluetooth Module” on page 7 - 2 for configuration instructions. Wireless LAN Module See the introduction in “Wireless LAN Module” on page 7 - 6, and check the installation procedure.
Drivers & Utilities 4 4 - 8
BIOS Utilities Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make.
BIOS Utilities POST Screen 5 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST Note: The POST screen as pictured right is for guideline purposes only. The POST screen on your computer may appear slightly different. If you disable the Boottime Diagnostic Screen, the POST screen will not appear. The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory).
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible. Non-Fatal Errors This kind of error still allows you to boot.
BIOS Utilities The Setup Program The Phoenix Setup program tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration). Entering Setup 5 To enter Setup, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few seconds after you turn on the system. If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup. Instructions on how to navigate each screen are in the box along the bottom of the screen.
BIOS Utilities Main Menu PhoenixBIOS Setup Utility Figure 5 - 2 Main Mai n Advanced Security Boot Exit Main Menu Item Specific Help System Time: System Date: [22:12:05] [05/23/2009] SATA Port 1 SATA Port 2 [FUJITSU MHY2120BH-(S] [HL-DT-ST DVDRAM GSA-] System Memory Extended Memory 633 KB 894 MB BIOS Revision KBC/EC Firmware Revision ******** ******** 5 F1 Esc Help Exit Select Item Select Menu -/+ Enter , , or selects field.
BIOS Utilities SATA Port 1/2 (Main Menu) Pressing Enter opens the sub-menu to show the configuration of an HDD/optical device on the computer’s SATA Port 1/2. Use the Auto (Type:) setting to have the items configured automatically for you. System/Extended Memory (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed.
BIOS Utilities Advanced Menu PhoenixBIOS Setup Utility Main A dvanced Advanced Security Boot Exit Item Specific Help 5 Figure 5 - 3 Advanced Menu Advanced Chipset Control Installed O/S: SATA Class ID: Legacy USB Support: Boot-time Diagnostic Screen: Reset Configuration Data: Power on Boot Beep: Battery Low Alarm Beep: [VISTA] [AHCI] [Enabled] [Disabled] [No] [Disabled] [Disabled] Only available if Windows Vista is selected as the O/S.
BIOS Utilities Installed O/S (Advanced Menu) This setting tells the computer what kind of operating system you’re using. Make sure you choose the correct setting for your O/S in order to prevent system problems. Note: If you select the Vista O/S then the SATA Mode Selection menu will become available. If you are installing the Windows XP O/S make sure you have set the appropriate operating system here in order to prevent system problems.
BIOS Utilities Reset Configuration Data (Advanced Menu) This item is set to No as default. You can change the setting to Yes if you have installed a new add-on which has reconfigured the system, resulting in such a serious system conflict that the operating system is unable to boot. Power On Boot Beep (Advanced Menu) Use this menu item to enable/disable the beep as the computer starts up. 5 Battery Low Alarm Beep (Advanced Menu) Use this menu item to enable/disable the battery low alarm beep.
BIOS Utilities Security Menu PhoenixBIOS Setup Utility Main Advanced Security Security Boot Security Menu Exit Item Specific Help F1 Esc Supervisor Password Is: User Password Is: Clear Clear Set Supervisor Password Set User Password [Enter] [Enter] Password on boot: [Disabled] Help Exit Select Item Select Menu -/+ Enter Supervisor Password controls access to the setup utility.
BIOS Utilities Password Warning 5 If you set a boot password (Password on boot is “Enabled“), NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk. 5 - 12 Security Menu Set User Password (Security Menu) You can set a password for user mode access to the PhoenixBIOS Setup Utility.
BIOS Utilities Boot Menu PhoenixBIOS Setup Utility Main Advanced Security Boot Figure 5 - 5 Exit Item Specific Help Boot priority order: 1: IDE CD: HL-DT-ST DVDRAM GSA-T50N-( 2: IDE 4: FUJITSU MHY2120BH-(S1) 3: USB FDC: 4: USB KEY: 5: USB CDROM: 6: USB HDD: 7: PCI BEV: JMC26X Fast Ethernet Contr 8: Excluded from boot order: : USB ZIP: : USB LS120: F1 Esc Help Exit Select Item Select Menu -/+ Enter Boot Menu Keys used to view or configure devices: Up and Down arrows select a device.
BIOS Utilities Exit Menu Figure 5 - 6 Exit Menu PhoenixBIOS Setup Utility Main Advanced Security Boot Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes 5 F1 Esc Help Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help.
Upgrading The Computer When Not to Upgrade Power Safety Warning 6 Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on. These procedures involve opening the system’s case, adding and sometimes replacing parts.
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. 1. 2. 3. 4. Turn the computer off, and turn it over. Slide the latch 1 in the direction of the arrow. Slide the latch 2 in the direction of the arrow, and hold it in place. Slide the battery out in the direction of the arrow 3 .
Upgrading The Computer HDD System Warning 6 New HDD’s are blank. Before you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CD-ROMs and FDDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.
Upgrading The Computer 4. 5. Grip the tab and slide the hard disk in the direction of arrow 4 Lift the hard disk out of the bay 5 . .
Upgrading The Computer 6. 7. Remove the screw(s) 6 and the adhesive cover 7 . Reverse the process to install a new hard disk drive (do not forget to replace all the screws and covers). 6 6 Figure 6 - 4 HDD Cover Removal 6 - 6 Upgrading the Hard Disk Drive 7 Hard Disk Screws & Cover The hard disks and covers pictured here may appear slightly different from your model design (these designs are subject to change and upgrade without notice).
Upgrading The Computer Upgrading the Optical (CD/DVD) Device 1. 2. 3. 4. 5. 6. Turn off the computer, and turn it over and remove the battery. Model A: Locate the RAM & CPU bay cover and remove screws 1 - 3 . Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. Carefully disconnect the fan cable 4 , and remove the cover 5 . OR Model B: Locate the hard disk bay cover and loosen screws 1 & 2 . Remove the hard disk bay cover 3 .
Upgrading The Computer 7. 8. Remove the screw at point 6 , and use a screwdriver to carefully push out the optical device at point 7 . Reverse the process to install the new device (make sure you replace the bay cover for Model A computers and align the cover correctly - see “Model A Cover Alignment” on page 6 - 12).
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 200 pin Small Outline Dual In-line (SODIMM) DDRII (DDR2) type memory modules (see “Memory” on page C - 2 for details of supported module types). 1. 2. Turn off the computer, and turn it over and remove the battery. Locate the RAM & CPU bay cover and remove screws 1 - 3 .
Upgrading The Computer 3. 4. Carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. Carefully disconnect the fan cable 4 , and remove the cover 5 . Fan Cable & Cover 6 Make sure you reconnect the fan cable 4 before screwing down the bay cover. Note the information on replacing the RAM & CPU bay cover in “Cover Pins” on page 6 - 12. Model A 5 Contact Warning Be careful not to touch the metal pins on the RAM module’s connecting edge.
Upgrading The Computer 5. 6. 7. 8. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( 6 & 7 ) in Figure 6 - 9. The RAM module will 8 pop-up, and you can remove it. Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. Figure 6 - 9 6 Model A 7 6 Model B 7 RAM Module Removal 6 Model A Model B 8 9.
Upgrading The Computer Cover Pins 6 Note that Model A computers have four cover pins and Model B computers have five cover pins. These pins need to be aligned with slots in the case to insure a proper cover fit, before screwing down the bay cover 10. Press the module in and down towards the mainboard until the slot levers click into place to secure the module. 11.
Modules & Options Chapter 7: Modules & Options Overview This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. • • • • Bluetooth Module Wireless LAN Module PC Camera Module 3.75G/HSPA Module Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Bluetooth Module The operating system’s Bluetooth Devices control panel is used to configure the Bluetooth settings in Windows Vista, and therefore does not require a driver.
Modules & Options Bluetooth Configuration in Windows Vista Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). To Turn the Bluetooth Module On 1. 2. 3. Press the Fn + F12 key combination to power on the Bluetooth module. A Bluetooth icon will appear in the taskbar (see sidebar).
Modules & Options To Add a Bluetooth Device 1. 2. Figure 7 - 2 Add Bluetooth Device Wizard 3. 4. 5. Access the Bluetooth Devices control panel. Click Options (tab), and make sure that Allow Bluetooth devices to connect to this computer check box (Connections) has a tick inside it. Click Devices (tab), and then click Add. The Add Bluetooth Device Wizard will appear. Click to select “My device is set up and ready to be found”, and then click Next. 6. 7. 8.
Modules & Options To Change Settings for the Bluetooth Device 1. 2. Access the Bluetooth Devices control panel. Click on the device you want to change and click Properties to: • • Change the name of the device (click General, type a new name and click OK). Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK). To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3. Access the Bluetooth Devices control panel.
Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + F11 key combination to toggle power to the WLAN module, and check the indicator to see if the module is powered on or not (see Table 1 - 6, on page 1 - 14/ Table 1 - 4, on page 1 - 10). Wireless LAN Module If you have included a 802.
Modules & Options Connecting to a Wireless Network Make sure the Wireless LAN module is turned on. 1. Click the taskbar wireless icon , and then click Connect to a network (or rightclick the icon , and then click Connect to a network). Figure 7 - 5 Taskbar Menus Click icon Right-click icon 2. 3. In the Show list, click to choose Wireless from the drop-down menu. A list of currently available networks will appear.
Modules & Options 4. 5. Click a network, and then click Connect. If you do not see a network you want to connect to, click Set up a connection or network (a list of options will appear allowing manual searching, and creating a new network). 6. Move the cursor over the taskbar icon Figure 7 - 7 Connecting 7 Figure 7 - 8 Connection Status 7 - 8 Wireless LAN Module to see the connection status (see below).
Modules & Options 7. To disconnect from the wireless network you can click the taskbar wireless icon , and then select Connect or disconnect to access the network menu, and click Disconnect (or right-click the icon , and then click Disconnect from). Click icon Security Enabled Networks You should try to make sure that any network you are connecting to is a secure network. Connecting to unsecure networks may allow unauthorized access to your computer, documents, websites and files etc.
Modules & Options Windows Mobility Center The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. To access the Windows Mobility Center: 1. 2. 3. 7 Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Windows Mobility Center (Mobile PC). Click the button to Turn wireless off/on, or click the icon to access the network menu.
Modules & Options PC Camera Module If you have included a PC Camera module in your purchase option, make sure that the PC Camera module is on before installing the driver. Use the Fn + F10 key combination (see “Function/Hot Key Indicators” on page 1 - 14) to toggle power to the PC Camera module. When the PC Camera module is powered on, the indicator will briefly be displayed. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3.
Modules & Options PC Camera Screen Refresh 7 If you find that the screen refresh rate is subject to lag or stuttering, then reduce the window size, or adjust the Output Size and/or Color Space Compression. PC Camera Driver Installation 1. Make sure the module is powered on, then insert the Device Drivers & Utilities + User’s Manual disc into the CD/DVD drive. 2. Click Option Drivers (button). 3. Click 2.Install Camera Driver > Yes. 4. Choose the language you prefer and click Next > Next. 5.
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. 2. 3. 4. Click Start, and click Control Panel (or point to Settings and click Control Panel). Double-click Sound (Hardware and Sound). Click Recording (tab). Right-click Microphone (Realtek High Definition Audio) and make sure the item is not disabled. 5. Double-click Microphone (or select Properties from the right-click menu). 6.
Modules & Options Figure 7 - 11 Audio Setup for PC Camera Right-click 7 7 - 14 PC Camera Module
Modules & Options BisonCap BisonCap is a video viewer for general purpose video viewing and testing, and for capturing video files to .avi format. 1. 2. 3. Run the BisonCap program from the Start > Programs/All Programs > BisonCam menu (it is recommended that you set the capture file before the capture process - see Set Capture File below). Go to the Capture menu heading (if you wish to capture audio check “PC Camera Audio Setup” on page 7 - 13) and select Start Capture.
Modules & Options Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties). If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive.
Modules & Options Eliminating Screen Flicker If you find that the video screen in the BisonCap program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. 2. 3. Run the BisonCap program. Go to Options and scroll down to select Video Capture Filter.... Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Modules & Options Zoom The BisonCap program allows you to zoom the camera in and out. 1. 2. Run the BisonCap program. Go to Zoom and select Zoom Out/Zoom In. Figure 7 - 13 Zoom/Setting 7 Snapshot Folder The Snapshot folder’s default location is on the desktop. Do not move this folder or an error may appear when you try to take a still picture. Taking Still Pictures The BisonCap program allows you to take still pictures. 1. 2. 3. Run the BisonCap program. Go to Options and select Take Picture.
Modules & Options 3.75G/HSPA Module If you have included an optional 3.75G/HSPA (High Speed Packet Access) module (see “Communication” on page C - 3 for specification details) in your purchase option, you will have the appropriate application (HSPA Modem Interface or Mobile Partner) provided for your particular module. Follow the instructions on page 7 21 to install the USIM card (supplied by your service provider), and then install the application (see over for further details). Important Notice - 3.
Modules & Options 3.75G/HSPA Modules & System Wake Up Note that the 3.75G modules DO NOT support system wake up on 3.75G/HSPA modem activity. 7 Before installing the application, make sure that the 3.75G/HSPA module is ON (installing the driver with the module off will not allow the software to detect the module hardware correctly). Use the Fn + key combination (see “Function/Hot Key Indicators” on page 1 - 14) to toggle power to the 3.75G/HSPA module. When the 3.
Modules & Options 1. 2. Turn off the computer, and turn it over and remove the battery. Locate the RAM & CPU bay cover and remove screws 1 - 3 (the SIMLOCK is located at point 4 ), then carefully (a fan and cable are attached to the under side of the cover) lift up the bay cover. Carefully disconnect the fan cable 5 , and remove the cover.
Modules & Options 3. 4. 5. Insert the USIM card as you would into your mobile phone. Slide the SIMLOCK towards the hinge in order to release the lock and lift it up. Insert the USIM card as illustrated in (Figure 7 - 15) and close the SIMLOCK. 6. Lock the SIMLOCK by pushing it in the direction of the arrow in Figure 7 - 16 until it clicks into the lock position. Figure 7 - 15 Insert the USIM Card 7 Figure 7 - 16 SIMLOCK Lock 7 - 22 3.
Modules & Options 7. Replace the bay cover (see sidebar) and screws (make sure you reconnect the fan cable before screwing down the bay cover). Cover Pins Model A Model B Note that Model A computers have four cover pins and Model B computers have five cover pins. These pins need to be aligned with slots in the case to insure a proper cover fit, before screwing down the bay cover Figure 7 - 17 Cover Pin Alignment 3.
Modules & Options HSPA Modem Interface Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. 7 Use the Fn + key combination to toggle power to the 3.75G/HSPA module, and check the indicator to see if the module is powered on or not (see Table 1 - 6, on page 1 - 14/ Table 1 - 4, on page 1 - 10). With the 3.
Modules & Options HSPA Modem Interface The connection information is stored on the USIM card supplied by the service provider. 1. 2. 3. 4. 5. Power on the 3.75G/HSPA module using the Fn + key combination. Access the HSPA Modem Interface from the Start menu (Start > Programs/All Programs > HSPA Modem > HSPA Modem), or by double-clicking the desktop icon . If a USIM card is not installed then a message will appear to notify you of this (click OK to close the message and install the USIM card).
Modules & Options 6. Click Connect to connect to your service provider. 7. The message “Network is connected” will be displayed when the network connection is successful. 8. You can then access the internet, download e-mail etc. as per any internet connection. Figure 7 - 19 Connecting to Network 7 Figure 7 - 20 Network is Connected 7 - 26 3.
Modules & Options 9. While you are connected the upper right corner of the HSPA Modem interface will display the upload and download rates, and the taskbar icon will display the connection speed. Figure 7 - 21 Uploading/ Downloading Rates and Speed 10. To disconnect click the Disconnect icon (Connection Manager). 11. The program will disconnect from the service provider. 12. The module will still be on, and you will need to press the Fn + key combination to turn it off. Adding a Profile 1. 2.
Modules & Options 3. 4. Click Add (button) and input any Network Settings required by your service provider. Click OK to save the profile. Figure 7 - 23 Network Settings & Profiles 7 5. 6. You can Edit or Delete profiles from the Profiles tab. To use a profile click to select it, and then click Apply (button) and the settings will be transferred to Connection Manager. 7 - 28 3.
Modules & Options Contacts 1. 2. Access the HSPA Modem Interface from the Start menu (Start > Programs/All Programs > HSPA Modem > HSPA Modem), or by clicking the desktop icon. Click Contacts (button). Figure 7 - 24 Network Settings & Profiles 7 3. 4. 5. 6. Click Refresh (button) to download the contacts from the USIM card to the computer. The Contacts will then be displayed. Double-click any contact to edit the information (or right-click and select Edit).
Modules & Options Messages 1. SMS Service 2. Access the HSPA Modem Interface from the Start menu (Start > Programs/All Programs > HSPA Modem > HSPA Modem), or by clicking the desktop icon. Click Messages (button). In addition to standard internet services you may also send and receive SMS text messages using the HSPA Modem Interface, if your service supports SMS. 7 Figure 7 - 25 Network Settings & Profiles 3. 4. 5.
Modules & Options 6. 7. 8. Click to select a contact from the list and then click Add (button) and the phone number will automatically be added to the recipient field. Type the message information into the message body and click Send (button) to send it, or Save to draft (button) to save the message. Select any message to forward or delete it, or to reply to it. Settings 1. 2.
Modules & Options 3. 4. 5. Click OK alongside any of the options to configure the settings. The Network can be configured for an Automatic (usually from the USIM card) or Manual connection. The Network Mode can be configured for any appropriate mode required. Figure 7 - 27 Settings - Network/ Network Mode 7 6. 7. 8. You can also change your settings for the Pin #, and input your phone number. Exiting the program DOES NOT turn off the 3.
Modules & Options Mobile Partner With the 3.75G/HSPA module and USIM card (supplied by your service provider) installed you may then install the Mobile Partner application. The Mobile Partner application allows you to directly access your HSPA internet service from the computer. Mobile Partner Application Installation 1. Enable power to the module by pressing the Fn + key combination (the on screen icon will indicate the module’s power status).
Modules & Options Mobile Partner Application Mobile Partner Help To get help on Mobile Partner configuration and settings, click the Help menu and select Online Help or press F1. You will need to contact your service provider to obtain the exact details of how exactly to configure the settings on this page. Profile Management 1. 2. 3. 4. 7 5. Power on the 3.75G/HSPA module using the Fn + key combination.
Modules & Options Connecting to the Service Provider 1. 2. 3. 4. Power on the 3.75G/HSPA module using the Fn + key combination. Access the Mobile Partner application from the Start menu (Start > Programs/ All Programs > Mobile Partner), or by double-clicking the Mobile Partner icon on the desktop . The software will run and you can select the Profile Name from the menu. Click Connect to begin the connection process. Figure 7 - 29 Connect 7 5.
Modules & Options 6. When the connection is successful you can move the cursor over the network icon in the taskbar to display the connection information. 7. You can then access the internet, download e-mail etc. as per any internet connection. While you are connected the indicators in the Mobile Partner window will display uploading and downloading icons and a network icon in the taskbar . Figure 7 - 31 Connected Taskbar Notification 8. 9. 7 To disconnect click the Disconnect and select Disconnect.
Modules & Options 11. The module will still be on, and you will need to press the Fn + key combination to turn it off. 12. If you click the Mobile Partner close icon a message will be displayed asking you to click OK to confirm the program exit and to terminate the connection. Figure 7 - 33 Exit Prompt 13. Exiting the program terminates the connection, but DOES NOT turn off the 3.
Modules & Options 7 7 - 38
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working. Check the LED Power & Communication Indicators (see “LED Indicators” on page 1 - 10) to see the computer’s power status.
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet. • Run maintenance programs on your hard disk and OS as often as you can. You may schedule these programs to run at times when you are not using your computer.
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet. • Be careful when opening e-mail from sources you don’t know.
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing. • Read the documentation.
Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. • Don’t over complicate things.
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t work. Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts. The battery LED power indicator blinking orange. , is Low Battery. Plug in the DC power source.
Troubleshooting Problem The computer feels too hot. Possible Cause - Solution Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating” on page 1 - 18). Make sure you’re using the correct adapter.
Troubleshooting Problem You forget the boot password. Possible Cause - Solution If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Troubleshooting Problem Unwelcome typing. numbers Possible Cause - Solution appear when If the LED is lit, then Num Lock is turned ON. (see “LED Indicators” on page 1 - 10). Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work. 8 The system freezes or the screen goes dark.
Troubleshooting Problem Possible Cause - Solution The Wireless LAN/Bluetooth/3.5G modules cannot be detected. The modules are off. Check the LED indicator and/or function key indicator to see if the WLAN/Bluetooth/3.75G/HSPA module is on or off (see “LED Indicators” on page 1 - 10). If the LED indicator is off, then press the Fn + F11 (WLAN), Fn + F12 (Bluetooth) or Fn + (3.
Troubleshooting Problem Possible Cause - Solution The Hibernate function has disappeared. You have a computer with 4GB of RAM and have installed Windows Vista Service Pack 1. This is a known issue if your computer has 4GB of RAM and is running Windows Vista Service Pack 1. To re-enable Hibernate mode go to the Command Prompt and type the command “powercfg -h on” (make sure you are logged on as an Administrator): 1. 2. 3. 4. 5. 6. Click Start (menu button). Type “cmd” in the Start Search box .
Troubleshooting Screen Resolution Error If you are experiencing either screen resolution reduction, or screen flickering after resuming from Sleep in Windows Vista only then follow the instructions below to fix this problem. This error arises in compliance with Windows Vista policy, which triggers TMM (Transient Multi-Monitor Manager) when the notebook lid (S3) is closed. TMM disconnects the LCD display from the OS and then adds the LCD display back when the lid is opened.
Troubleshooting 3. 4. 5. Double-click Task Scheduler Library > Microsoft > Windows. Click MobilePC to open the control panel. Right-click TMM and select Disable. 8 Figure 8 - 2 - TMM Disable 6. Close all the control panels.
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Interface (Ports & Jacks) Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer. External Monitor (VGA) Port This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD.
Interface (Ports & Jacks) Item Description Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. S/PDIF-Out Jack This S/PDIF (Sony/Philips Digital Interface Format) Out Jack allows you to connect your DVDcapable PC to a Dolby AC-3 compatible receiver for “5.1” or ‘dts’ surround sound. USB 2.0/1.1 Ports These USB 2.0 compatible ports (USB 2.0 is fully USB 1.
Interface (Ports & Jacks) A A - 4
Appendix B: ATI Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - 20. Video Card Options ATI Video Driver Installation Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 3. Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button). 1. Click 1.Install Video Driver > Yes. 2. Click Next > Install (button). 3.
ATI Catalyst® Control Center Adjust the video settings from the ATI Catalyst® Control Center. ATI Taskbar Icon The ATI Catalyst Control Center can be accessed as above or by double-clicking the icon in the taskbar (or by right-clicking the icon and selecting Catalyst Control Center). If you don’t see the ATI icon in the taskbar, click Preferences (tab) in the ATI Catalyst® Control Center, and select Enable System Tray Menu. B 1. 2. 3. 4. 5. Open the Display Settings (see page 1 - 20) control panel.
The ATI Catalyst® Control Center provides additional video configuration controls and tools which allow quick access to features such as display options, 3D Settings, color and Help menus etc. Adjust settings from the options in the Graphics Settings Tree View pane. Help Menus Click Help (tab) and select an option from the drop down menu. Press F1 to bring up Help for any currently selected page.
Display Devices Besides the built-in LCD, you can also use an external monitor/flat panel display as your display device. The following are the display options: Attaching Other Displays Configuring an External Display in Windows Vista 1. 2. 3. Attach your external display to the external monitor port and turn it on.
Configuring an External Display using the ATI Catalyst Control Center Alternatively you can use the ATI Catalyst Control Center to configure any attached displays. 1. 2. 3. 4. 5. 6. 7. Attach your external display to the external monitor port and turn it on. Go to ATI Catalyst Control Center (see “ATI Catalyst® Control Center” on page B - 2). Select Displays Manager from the Graphics Settings Tree View pane. Attached displays will appear in the Desktop and Display Setup box.
Function Keys You can use the Fn + F7 key combination to toggle through the display options: • Notebook Only • External Display Only • Notebook + External Display Give the displays enough time to refresh. Swap Display Mapping B If you wish to switch the Main and Clone displays, right-click either the Main or Clone icon (Displays Manager), and then click Swap Display Mapping. B - 6 Display Modes Display Modes Single Only one of your displays is used.
Clone Mode Clone Mode simply shows an exact copy of the Main display desktop on the other display(s). This mode will drive multiple displays with the same content. Use this feature to display the screen through a projector for a presentation. Selecting Display Modes Right-click the attached display icon and select an option (Clone or Extend) from the menu. Figure B - 5 Displays Manager Clone Mode Click Displays Properties to make adjustments for any attached displays.
Selecting Display Modes Right-click the attached display icon and select an option (Clone or Extend) from the menu. Extended Mode B When enabled, you can drag any icons or windows across to the other display desktop. It is therefore possible to have one program visible in one of the displays, and a different program visible in the other display.
Using New Display Detected to Enable Extended Mode 1. 2. 3. 4. 5. Attach your external display to the external monitor port and turn it on. If a New Display Detected window does not appear in Windows Vista, go to the Windows Mobility Center control panel (Mobile PC > Adjust commonly used mobility settings) and click Connect display. Click to select Show different parts of my desktop on each display (extended). Click Right or Left under Extend your desktop. Click Apply > OK.
Using Display Settings to Enable Extended Mode Display Settings Extended Desktop 1. 2. 3. Use the control panel to drag the monitors to match the physical arrangement you wish to use. You can drag any icons or windows across to either display desktop, which makes it possible to have one program visible in one of the displays, and a different program visible in the other display.
Theater Mode Theater Mode enables you to display video playback in full screen on a secondary monitor. Theater Mode can be configured from the Avivo™ Video > Theater Mode tab in the Graphics Settings Tree View pane.
PowerPlay™ PowerPlay™ in the Graphics Settings Tree View pane allows you to set your graphics processor settings for higher performance or longer battery life.
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your service center for details.
Specifications Processor Video Adapter Keyboard & Pointing Device AMD® Athlon™ 64 Processor: TF20 (1.
Specifications Communication Power Dimensions & Weight Built-In 10/100Mb Base-TX Ethernet LAN 802.11b/g/n Wireless LAN Half Mini-Card Module with PCIe interface (Option) Bluetooth 2.1 + EDR (Enhanced Data Rate) Module (Factory Option) 1.3M Pixel USB PC Camera Module (Factory Option) UMTS/HSPDA-based 3.
Specifications C C - 4
Appendix D: Windows XP Information This Appendix contains information (including control panel information, driver installation etc.) for users of the Windows XP OS.
Operating System Setup If you are installing new system software, or are re-configuring your computer for a different system, make sure you configure the appropriate OS setting in the BIOS before installing a new operating system. 1. Start-up the computer and press to enter the BIOS. 2. Go to the Advanced menu, select “Installed O/S” and make sure the appropriate operating system is selected. 3.
DVD Regional Codes Changing DVD Regional Codes Go to the Control Panel and double-click System > Hardware (tab), click Device Manager, then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialogue box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code. DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times. The fifth selection is permanent.
Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can customize the look of the Start menu by right-clicking the Start menu and selecting Properties from the menu.
TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. Once you have installed the TouchPad driver (see “TouchPad” on page D - 35) you can configure the functions by double-clicking the TouchPad driver icon on the taskbar.
Function/Hot Key Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility is installed. Fn Keys Function Fn Keys Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F5/F6 Fn + _ Fn + F1 Fn + F2 Fn + F3 Volume Decrease/Increase 3.
Audio Features You can configure the audio options on your computer from the Sounds and Audio Devices Windows control panel, or from the Realtek HD Audio Manager icon in the taskbar/control panel (this will bring up the Realtek Audio Configuration menus). The volume may also be adjusted by means of the Fn + F5/F6 key combination. Sound Volume Adjustment How high the sound volume can be set depends on the setting of the volume control within Windows (and the volume control function keys on the computer).
Video Features You can configure display options, from the Display Settings control panel in Windows as long as the appropriate video driver is installed. For more detailed video information see “ATI Catalyst® Control Center” on page D - 10. To access Display Settings in Windows: To access Display Properties in Windows: 1. 2. 3. 4. 5. 6. Click Start, point to Settings and click Control Panel (or just click Control Panel). Double-click Display (icon) - In the Appearances and Themes category.
Display Devices & Options Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display as your display device. 4 1 2 5 3 Video Options Note that card types, specifications and drivers are subject to continual updates and changes. Check with your service center for the latest details on video cards supported.
ATI Catalyst® Control Center Adjust the video settings from the ATI Catalyst® Control Center. ATI Taskbar Icon The ATI Catalyst Control Center can be accessed as above or by double-clicking the icon in the taskbar (or by right-clicking the icon and selecting Catalyst Control Center). If you don’t see the ATI icon in the taskbar, click Preferences (tab) in the ATI Catalyst® Control Center, and select Enable System Tray Menu. 1. Open the Display Settings (see page 1 - 20) control panel. 2.
The ATI Catalyst® Control Center provides additional video configuration controls and tools which allow quick access to features such as display options, 3D Settings, color and Help menus etc. Adjust settings from the options in the Graphics Settings Tree View pane. Help Menus Click Help (tab) and select an option from the drop down menu. Press F1 to bring up Help for any currently selected page.
Display Devices You can use the Fn + F7 key combination to toggle through the display options: • Notebook Only • External Display Only • Notebook + External Display Make sure you give the displays enough time to refresh. Attaching Other Displays Besides the built-in LCD, you can also use an external VGA monitor (CRT) or external Flat Panel Display as your display device. A VGA monitor/Flat Panel Display connects to the external monitor port. The following display modes are available.
Configuring an External Display (ATI Catalyst Control Center) You can use the ATI Catalyst Control Center to configure any attached displays. 1. 2. 3. 4. 5. 6. 7. Attach your external display to the external monitor port and turn it on. Go to ATI Catalyst Control Center (see page D - 10). Select Displays Manager from the Graphics Settings Tree View pane. Attached displays will appear in the Desktop and Display Setup box (if disabled the display they will appear in the box below).
Selecting Display Modes Clone Mode Clone Mode simply shows an exact copy of the Main display desktop on the other display(s). This mode will drive multiple displays with the same content. Use this feature to display the screen through a projector for a presentation. Right-click the attached display icon and select an option (Clone, Extend or Stretch) from the menu. Figure D - 10 Displays Manager Clone Mode Click Display Properties to make adjustments for any attached displays.
Extended Mode In Extended Mode each monitor can be configured separately with the Windows desktop stretched between the two monitors (except the taskbar). This configuration is recommended if you are using two monitors of different size, as you may configure the best resolution, refresh rates and color quality for each display. Click either the Graphics Adapter pop-up menu, or click the icon for the appropriate display.
Selecting Display Modes Right-click the attached display icon and select an option (Clone, Extend or Stretch) from the menu. Stretched Mode In Stretched Mode the desktop can be though of as equal to the sum of the two individual monitors, depending on the stretch mode chosen. Therefore if the monitors are stretched horizontally, and both are running at 1024 (H) * 768 (V), then the desktop area can be considered as 2048 (H) * 768 (V).
To Enable Extended Desktop (Windows Display Properties) 1. 2. 3. 4. 5. Attach your external display to the external monitor port and turn it on. Click Start, point to Settings (or click Control Panel) and click Control Panel (if you are in Category View choose Appearance and Themes). Double-click Display (icon). In the Display Properties dialog box, click Settings (tab). Click the monitor icon (e.g. 2 ), and make sure you have checked “Extend my Windows desktop onto this monitor.” and click Apply.
Theater Mode Theater Mode enables you to display video playback in full screen on a secondary monitor. Theater Mode can be configured from the Avivo™ Video > Theater Mode tab in the Graphics Settings Tree View pane.
PowerPlay™ PowerPlay™ in the Graphics Settings Tree View pane allows you to set your graphics processor settings for higher performance or longer battery life.
OS Note Power management functions will vary slightly depending on your operating system. For more information it is best to refer to the user’s manual of your operating system. (Note: All pictures used on the following pages are from the Windows XP OS.) Power Management Features To conserve power, especially when using the battery, your computer uses the ACPI power management system.
The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/DC adapter will damage the computer and its components. 1. 2. 3. 4. Attach the AC/DC adapter to the DC-in jack on the left of the computer. Plug the AC power cord into an outlet, and then connect the AC power cord to the AC/DC adapter. Raise the lid/LCD to a comfortable viewing angle. Press the power button to turn “On”.
Shutdown Note that you should always shut your computer down by choosing the Turn Off Computer command from the Start menu in Windows. This will help prevent hard disk or system problems. Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.
Power Schemes You can set your computer to conserve power through individual components by means of Power Schemes. You can also adjust the settings for each scheme to set the monitor to turn off after a specified time, and the computer's hard disk motor to turn off if the hard disk drive has not been accessed for a specified period of time (if the system reads or writes data, the hard disk motor will be turned back on).
Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source.
System Power Options You can use the system power options to stop the computer’s operation and restart where you left off. This system features Stand by and Hibernate sleep mode levels (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - see “Hibernate” on page D - 26). Hibernate Mode vs. Shutdown Hibernate mode and Shutdown are the same in that the system is off and you need to press the power button to turn it on.
Stand by System Resume The system can resume from Stand by mode by: • Pressing the power button • Pressing the Sleep/ Resume key combination • An incoming call received on the modem (if enabled) Stand by saves the least amount of power, but takes the shortest time to return to full operation. During Stand by the hard disk is turned off, and the CPU is made to idle at its slowest speed. All open applications are retained in memory.
Configuring the Power Button The power button may be set to send the computer in to either Stand by or Hibernate mode. In Stand by mode, the LED will blink green. In Hibernate mode the LED will be off (battery) or orange (AC/DC adapter). If you are in a power saving mode set to save power through individual components (e.g. hard disk, monitor), the LED will remain green. Sleep Button You may also configure the Sleep/Resume key combination (Fn + F4) from the menu illustrated.
Low Battery Warning When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted. Battery Information Please follow these simple guidelines to get the best use out of your battery. New Battery Always completely discharge, then fully charge, a new battery (see “Battery FAQ” on page D - 31 for instructions on how to do this).
Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you need to remove the battery for any reason, see “Removing the Battery” on page 6 - 3. Recharging the Battery with the AC/DC Adapter The battery pack automatically recharges when the AC/DC adapter is attached and plugged into an electrical outlet.
Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g. the battery is bent out of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center.
Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer by yourself even when you see a message that indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
Driver Installation Insert the Device Drivers & Utilities + User’s Manual disc, click Install Drivers/Option Drivers (button) and then click the appropriate driver name from the Drivers Installer menu. Follow the instructions to install the driver. Alternatively click Start, navigate (Browse..) to the executable file and then follow the manual setup instructions. D Figure 5 - Drivers Installer Screen 1 D - 32 Driver Installation 1.
WinXP SP2 Driver Page # Video Page D - 34 AMD CPU Page D - 34 Audio Page D - 35 LAN Page D - 35 TouchPad Page D - 35 CardReader Page D - 35 Hot Key Page D - 35 WLAN Module Page D - 44 WLAN Module Page D - 42 3.75G/HSPA Module Page D - 52 Page D - 53 Table D - 3 - Driver Installation Updating/Reinstalling Individual Drivers If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.
Driver Installation Procedure Windows XP Service Pack 3 Make sure you install Windows XP Service Pack 3 (or a Windows XP version which includes Service Pack 3) before installing any drivers. Driver Installation General Guidelines The driver installation procedure outlined in this Chapter are accurate at the time of going to press. Drivers are always subject to upgrade and revision so the exact procedure for certain drivers may differ slightly.
Audio 1. Click 3.Install Audio Driver > Yes. 2. Click Next. 3. Click Finish to restart the computer. CardReader 1. Click 6.Install CardReader Driver > Yes. 2. Click Install. 3. Click Finish. LAN 1. Click 4.Install LAN Driver > Yes. 2. Click Install. 3. Click Finish. 4. The network settings can now be configured. Hot Key 1. Click 7.Install Hotkey Utility > Yes. 2. Click Next > Install. 3. Click Finish > Finish to restart the computer. TouchPad 1. Click 5.Install Touchpad Driver > Yes. 2.
Module Drivers See the following pages for the driver installation procedures for any of the optional modules included in your purchase configuration. Wireless LAN, Bluetooth & 3.75G/HSPA Modules Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Wireless LAN, Bluetooth & 3.
Bluetooth Module The operating system’s Bluetooth Devices control panel is used to configure the Bluetooth settings in Windows XP, and therefore does not require a driver. Use the Fn + F12 key combination (see “Function/Hot Key Indicators” on page D - 6) to toggle power to the Bluetooth module. When the Bluetooth module is powered on, the LED will be orange and the indicator will briefly be displayed.
Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Bluetooth Local Area Connection Icon If you want to display the Local Area Connection icon for the Bluetooth connection in the taskbar, set it up as follows: 1.
Bluetooth Configuration in Windows XP Setup your Bluetooth Device so the Computer Can Find it 1. 2. Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Make the device discoverable (to do this check your device documentation). Bluetooth Taskbar Icon To Turn the Bluetooth Module On 1. 2. 3. Press the Fn + F12 key combination to power on the Bluetooth module. A Bluetooth icon will appear in the taskbar (see sidebar).
Passkey Options You can allow the system to choose a passkey for you. You will then be prompted to enter the generated passkey on your Bluetooth device. To Add a Bluetooth Device 1. Access the Bluetooth Devices control panel. 2. Click Options (tab), and make sure that Allow Bluetooth devices to connect to this computer check box (Connections) has a tick inside it. 3. Click Devices (tab), and then click Add. 4. The Add Bluetooth Device Wizard will appear. 5.
To Change Settings for the Bluetooth Device 1. 2. • • Access the Bluetooth Devices control panel. Click on the device you want to change and click Properties to: Change the name of the device (click General, type a new name and click OK). Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK). To Make your Computer Discoverable to Bluetooth Devices 1. 2. 3. Access the Bluetooth Devices control panel.
Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Use the Fn + F11 key combination to toggle power to the WLAN module, and check the indicator to see if the module is powered on or not (see Table D - 2, on page D - 6/ Table 1 - 4, on page 1 - 10). WLAN Module Before installing the optional 802.
Network Connection Use the Windows Network Connections control panel to access available wireless networks (Start > Settings > Network Connections or Start > Connect To > Show all Connections).
Taking Still Pictures Double-click the My Computer icon on the desktop, or go the Start menu and point to My Computer, then click it. Double-click the camera icon. Click Take a new picture in the Camera Tasks box. . PC Camera Module Before installing the optional PC Camera module driver use the Fn + F10 key combination to toggle power to the module. The PC Camera module uses the BisonCap application to capture video files. PC Camera Driver Installation 1.
PC Camera Audio Setup (all camera modules) If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. 1. Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then doubleclick the Sounds & Audio Devices icon (Sounds, Speech, and Audio Devices in Category View). 2. Click Advanced in the Volume > Device volume tab. 3. Click Options and scroll down and click Properties. 4.
Pre-Allocating File Space You may pre-allocate the file size (File > Allocate File Space) for the capture file in the BisonCap program. Pre-allocating space on the hard disk can improve the capture quality (particularly of large capture files), by reducing the amount of work the hard disk has to do in finding space for the video data as it is being captured. See also “Reducing Video File Size” on page D - 47.
Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties) If necessary you can remove the recorded video file to a removable medium e.g. CD, DVD or USB Flash drive. Note that the Windows XP system requires a minimum of 1.
Eliminating Screen Flicker If you find that the video screen in the BisonCap program is flickering, you can try to adjust the setting in the Video Capture Filter options. 1. Run the BisonCap program. 2. Go to Options and scroll down to select Video Capture Filter.... 3. Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Zoom The BisonCap program allows you to zoom the camera in and out. 1. 2. Run the BisonCap program. Go to Zoom and select Zoom Out/Zoom In. Figure D - 8 Zoom/Setting Snapshot Folder Taking Still Pictures The BisonCap program allows you to take still pictures. 1. 2. 3. Run the BisonCap program. Go to Options/Capture and select Take Picture/Snapshot. The picture (in JPEG format) will be placed in the Snapshot folder desktop. on the The Snapshot folder’s default location is on the desktop.
3.75G/HSPA Module Options There are two optional 3.75G/HSPA modules available for this series of computer models. Each module is supplied with the appropriate application software. The module type supplied may depend upon the computer model purchased. Check with your service center for details. 3.75G/HSPA Module If you have included an optional 3.
Before installing the application, make sure that the 3.75G/HSPA module is ON (installing the driver with the module off will not allow the software to detect the module hardware correctly). Use the Fn + key combination (see “Function/Hot Key Indicators” on page D - 6) to toggle power to the 3.75G/HSPA module. When the 3.75G/HSPA module is powered on, the indicator will briefly be displayed. Make sure you install the drivers in the order indicated in Table D - 3, on page D - 33.
HSPA Modem Interface Installation With the 3.75G/HSPA module and USIM card (supplied by your service provider) installed you may then install the HSPA Modem Interface. The HSPA Modem Interface allows you to directly access your HSPA internet service from the computer. 1. Enable power to the module by pressing the Fn + key combination (the on screen icon will indicate the module’s power status).
Mobile Partner Application Installation With the 3.75G/HSPA module and USIM card (supplied by your service provider) installed you may then install the Mobile Partner application. The Mobile Partner application allows you to directly access your HSPA internet service from the computer. 1. Enable power to the module by pressing the Fn + key combination (the on screen icon will indicate the module’s power status).
D D - 54
