Full Product Manual

ManualsBrandsChiller Daddy ManualsKitchenUndersink Water Chiller

CHILLER DADDY

MODEL: CHL-501

Intended Use For:

Residential & Office

Water Chiller

OWNER’S

MANUAL

TABLE OF CONTENTS

1. FOR YOUR SAFETY

2. LOCATION

REQUIREMENTS

3. INSTALLATION

PROCEDURES

4. PRESSURE LIMITER (optional)

CLEANING & SANITIZING

STORAGE

7. QUICK CONNECTOR FITTINGS

PRIMARY COMPONENTS DIAGRAM

9. ADJUSTING THERMOSTAT

10.

SPECIFICATIONS

11. TROUBLESHOOTING GUIDE

12. WARRANTY & SERVICE

Chiller Daddy LLC

Huntington, IN 46750 USA

www.ChillerDaddy.com

▲ For best use of your Chiller we advise reading these instructions carefully as they contain important information.

▲ Keep this manual for future reference.

▲ Chiller Daddy LLC reserves the right to change specifications and design without notice.

▲ CHILLER DADDY® is the Registered Trademark of CHILLER DADDY LLC

Summary of content (8 pages)

PAGE 1
CHILLER DADDY® MODEL: CHL-501 Intended Use For: Residential & Office Water Chiller OWNER’S MANUAL TABLE O F CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. FOR YOUR SAFETY LOCATION REQUIREMENTS INSTALLATION PROCEDURES PRESSURE LIMITER (optional) CLEANING & SANITIZING STORAGE QUICK CONNECTOR FITTINGS PRIMARY COMPONENTS DIAGRAM ADJUSTING THERMOSTAT SPECIFICATIONS TROUBLESHOOTING GUIDE WARRANTY & SERVICE Chiller Daddy LLC Huntington, IN 46750 USA www.ChillerDaddy.
PAGE 2
1. WARNING - FOR YOUR SAFETY - READ THE FOLLOWING SAFETY PRECAUTIONS BEFORE OPERATING THE WATER CHILLER  To prevent electric shock, unplug the Chiller prior to servicing. Never remove the cover while the Chiller is still connected to electricity.  Never insert anything into the Chiller cabinet when it is connected to electricity. Prevent water from flowing into the Chiller metal cabinet or onto electrical parts.  Do not use with water that is microbiologically unsafe or of unknown quality.
PAGE 3
   allow 3/8” OD lines to connect the faucet are acceptable. Purge off all air from the water lines by slowly opening the faucet lever. A steady water stream of water assures all air is purged. Prior to drinking, flush water through Chiller for at least 2 minutes. Close the faucet and check all water tight connections. Plug in the Chiller and you will be able to enjoy cold water in about 30 minutes after completing installation.
PAGE 4
CAUTION: FAILURE TO ABIDE BY ABOVE PROCEDURE MAY INCUR PHYSICAL DAMAGE TO THE CHILLER’S COMPRESSOR. TO PROPERLY DISPOSE OF YOUR CHILLER - Your old Chiller may have used a regulated refrigerant in its cooling system. These refrigerants are believed to harm stratospheric ozone. If you are throwing away your old Chiller, make sure the refrigerant is removed and recovered for proper disposal by an EPA-certified technician.
PAGE 5
Step 4. Removing the Tube or Plug • • • • 8. PRIMARY COMPONENTS DIAGRAM 9. ADJUSTING THERMOSTAT  Make sure to completely eliminate all pressure before removing the tube from the Quick Connector Union fitting. Turn off the incoming feed water and open the faucet. When removing the tube or plugs, push and hold the collet clip in against the fitting as you pull the tube or plug out. This releases the tube or plug. Fittings and tubes can be reused.
PAGE 6
Model #: CHL-501 Product Type: Under Sink Water Chiller for Residential and Office Use Product Dimensions: L: 16" x W: 8" x H: 11.75" (406x203x300) Product Weight: 23.75 lbs (10.8 KG) Shipping Dimensions: L: 20.87" x W: 13" x H: 15.35" (530x330x390) Shipping Weight: 27.25lbs Product Color: Appliance Grade Designer Brushed Stainless Steel Cabinet Application: Chills Drinking Water for Residential and Office Use. Connects to RO Reverse Osmosis and Filtered Drinking Water Systems.
PAGE 7
UPC#: 850901003767 *See separate warranty description for details. ** Temperature range may be affected by proper ventilation to allow heat to vent away from the chiller. {***} Chiller Daddy® reserves the right to change specifications and design without notice. 11. TROUBLESHOOTING GUIDE TROUBLE POSSIBLE CAUSE REMEDY REFRIGERATION SYSTEM A. Compressor does not run. No electric power to outlet. The thermostat is misadjusted or defective. The line voltage is low. The compressor is defective. B.
PAGE 8
required level. The compressor motor is defective, causing the Chiller to cycle on the overload protector. F. The cold water flows slowly or not at all. The cold water thermostat is too low, causing ice to build up in the reservoir, blocking water flow. Return Chiller to authorized service center or factory for repair. Defrost Chiller. Adjust the thermostat to a warmer temperature. NOISE A. There is excessive noise coming from the Chiller, but it is otherwise operating normally.