MODEL 38-FP0001-01 (with Video Card) 38-FP0001-02 (without Video Card) User's Manual
Table of contents Precautions ............................................................................................... 2 Before First Use Names and Functions (Monitor) .......................................................... 3-4 Check Accessories ................................................................................. 3 Outer Dimension.................................................................................. 5-6 Installation .........................................................
Precautions Placement precautions • Avoid placing the unit in humid or dusty places, or where it will be exposed to excessive heat (direct sunlight, heaters, etc.) • Do not step on or set anything on the AC Power Cord. DAMAGE TO THE AC POWER CORD IS A SAFETY RISK AND CAN CAUSE A FIRE. • Install the unit only on a stable and smooth surface.
Before First Use Names and Functions (Monitor) Front View Display Screen NOTE ¡ When you move the LCD monitor, please unplug AC cables connected to AC-IN and disconnect the cables connected to the external equipment. ¡ When you carry the LCD monitor, please be careful not to shock it. To avoid damaging the LCD panel, be sure not to touch the LCD panel when carrying the monitor. Check Accessories Check that the main unit and all accessories are present.
38-FP0001-02 Rear View Ventilators Ventilators Ventilators Power Switch ( Turns the power to the monitor on and off.
Before First Use Outer Dimension Ventilators IR POWER External Control RGB 5 DVI AC-IN
38-FP0001-02 Ventilators Ventilators Ventilators 4-M6 (Depth : Min.12mm/Max.20mm) Ventilators Ventilators Mounting Area Ventilators Ventilators When you install the LCD Monitor, please take care the following: • Use the M6 screws only for installation. • The maximum length of the screw put through a hole is 20mm on the surface of a metal chassis (as shown right). Use the screw with effective length 12-20mm, if not it may damage to the LCD monitor.
Before First Use Installation Connect the Computers Before doing anything, make sure the Power Switch on the monitor and a computer is turned off. the cable(s) into the connector on the monitor securely and fix 1 Plug them in place with two screws (each). 2 Plug the other end of the cable(s) into the connector on a computer. 3 Plug the AC Power Cord into the AC-IN on the monitor. 4 Plug the Power Plug into an outlet. 5 Switch on the monitor before starting up a computer.
How to secure the monitor on a wall Note: The following figure is only recommended. M6 bolt (4 places) 38-FP0001-02 Vertical UP b Depth: Min. 12mm Max. 20mm Bracket (not included) Side view of the monitor Horizontal Rear view of the monitor M6 bolt (4 places) UP b Depth: Min. 12mm Max. 20mm Bracket (not included) Side view of the monitor Rear view of the monitor Caution Never cover the rear ventilators with cloth or something.
Before First Use Names and Functions (Remote Controller) Operating Range (when there is no obstacle) Horizontal 9 Vertical
Standby key Standby ON/OFF. Menu key Wide key Set the scale mode in wide. Numeric keys (see page 72) Used to switch each input signal. [0], [8] and [9] keys are not used. [1] Analog RGB1 selection [2] Digital RGB selection [3] Composite VIDEO selection [4] S-Video selection [5] Analog RGB2 selection [6] Component VIDEO selection [7] RGB+CSync selection 38-FP0001-02 Show Main menu. Used to move cursor leftward while displaying the menu. key (see page 72) Zoom out the picture.
Before First Use Preparation for remote control 1 Remove the battery compartment lid with pushing OPEN . OPEN Rear view sure and put two AA dry batteries into the remote controller. 2 Be Make sure of the direction of them as indicated inside the remote controller. OPEN the lid by sliding it up over the batteries until it is firmly in 3 Replace place.
LCD Monitor Instructions This LCD monitor decodes the signal from a computer automatically, and displays the image on a screen in accordance with the preset mode. Unless a display mode has been in preset table, the image is displayed under the similar mode in preset table. In this case, the adjustment for this LCD monitor must be done in accordance with a computer connected with. Please follow the OSD (On Screen Display) menu to adjust screen settings.
LCD Monitor Instructions Adjustment Items Adv pip(Advanced picture in picture) Menu (refer to page 29-30) H POSITION ‥ ‥ ‥ ‥ ‥ ‥ ‥ ‥ ‥Select the horizontal position of pip V POSITION ‥ ‥ ‥ ‥ ‥ ‥ ‥ ‥ ‥Select the vertical position of pip VIDEO FORMAT ‥ ‥ ‥ ‥ ‥ ‥ ‥Select the video format (ntsc/pal/secam) Note Adv pip Menu can be used when inputting Composite Video or S-Video signal and also selecting [small] or [medium] or [large] in [size] menu.
Mode You can change or indicate the signal input type following the steps. Change or indicate the input signal to change or indicate the current mode. Press [Source] key to indicate the current mode in the lower right corner of the screen. (Ex.) 38-FP0001-02 1. While the OSD (On Screen Display) is not displayed, it is possible Analog RGB1 1024 x 768 / 75 Hz Mode: 88 2. While displaying the current mode, press [Source] key again.
LCD Monitor Instructions Adjustment Procedure Before Adjustment The signal timing for a computer which this LCD monitor supports is listed in "Table of Preset Data" on Page 39, the recommended value of Vertical Frequency for this model is 60Hz. (Unlike CRT Monitors, the display becomes stable when Vertical Frequency is low.) It is recommend to set Vertical Frequency of a computer connected at 60Hz by "refresh rate setting" before starting adjustment procedure.
Move the cursor to Sub menu After Main menu item is selected, press [Menu ･Press [ Menu] key to return to Main menu from Sub menu. (Ex.) Brightness 25 - + Picture Contrast + Advanced H position 50 50 - Pip Adv pip Options Utilities V position 50 - + 15 1056 - + Main menu 5 Phase Frequency + + Scaling Wide Sub menu Select item of Sub menu Press [ ] or [ ] key as well as the Main menu item selection. (Ex.
LCD Monitor Instructions Adjustment Procedure 2. For the adjustment item like "brightness", press [−] or [＋] key to change levels of selected item. (Ex.) Brightness 25 - + Picture Contrast + Advanced H position 50 50 - Pip Adv pip Options Utilities V position 50 - + 15 1056 - + Main menu 7 Phase Frequency Scaling + + Wide Sub menu Adjustment or Setting For each item selected, the adjustment/setting has been made by pressing [ ] and/or [ ] key.
Adjustment for computer screen (Picture Menu) Manual Adjustment If you wish to adjust the screen finely or in case the result adjusted by Auto Adjust (see page 34) sequence is not sufficient enough, adjust the screen manually. 1 38-FP0001-02 A. Picture Menu Adjust the brightness 1. Select [Picture] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. (Ex.
LCD Monitor Instructions Adjustment Procedure (Picture Menu) 3. Use [ ] and/or [ By pressing [ ] key to adjust. (Interval: 0~100) ] key, the contrast (difference between bright and dark) becomes darker. By pressing [ ] key, the contrast (difference between bright and dark) becomes lighter. 3 Adjust the horizontal position (Analog mode only) 1. Select [Picture] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. (Ex.
Adjustment for computer screen 2. Select [V position] on the Sub menu with pressing [ ] or [ ] key. The selected item of [V position] turns blue. 5 ] and/or [ ] key to adjust. (Interval: 0~100) Press [ ] key to shift the screen to the top. Press [ ] key to shift the screen to the bottom. 38-FP0001-02 3. Use [ Adjust the phase (Analog mode only) 1. Select [Picture] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. Picture Advanced (Ex.
LCD Monitor Instructions Adjustment Procedure (Picture Menu) 3. Use [ 7 ] and/or [ ] key to adjust. By pressing [ ] key, the horizontal width becomes wider. By pressing [ ] key, the horizontal width becomes narrower. Adjust the scaling 1. Select [Picture] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. Picture Advanced Pip Adv pip Options Utilities (Ex.
Adjustment for computer screen (Advanced Menu) B. Advanced Menu 1 Adjust the color temperature (Preset) 1. Select [Advanced] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. Color (Ex.) Warm Neutral Cold user - + Picture User red Advanced User green - + Pip User blue - + 38-FP0001-02 You can adjust the color temperature for the screen manually. Three preset values of color temperature are set up at the time of factory shipments.
LCD Monitor Instructions Adjustment Procedure (Advanced Menu) Color (Ex.) Warm Neutral Cold user - + Picture User red Advanced User green - + Pip User blue - + Sub menu Adv pip Options Utilities Main menu 2. Select [Color] on the Sub menu with pressing [ ] or [ ] key. The selected item of [Color] turns blue. 3. Select [User] with [ ] and/or [ ] key. [user] turns red. Besides, [User red], [User green] and [User blue] are displayed. 4. Select [User red] with [ ] key.
Adjustment for computer screen (Pip Menu) C. Picture in picture Menu If you wish to adjust a pip(picture in picture), you can adjust the size, position, source, brightness, contrast, color, tint and sharpness manually. Adjust the size 1. Select [Pip] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. Size (Ex.
LCD Monitor Instructions Adjustment Procedure (Pip Menu) 2. Select [Pos] on the Sub menu with pressing [ ] or [ ] key. The selected item of [Pos] turns blue. 3. Use [ ] and/or [ When pressing [ ] key to select the position. ] key, the position of pip(picture in picture) can be selected / according to the order / / / / / / / in sequence. When pressing [ ] key, the position of pip order is scrolled in opposite to the above order. 3 Change the input signal 1.
Adjustment for computer screen 4 Adjust the brightness (Video signal only) You can adjust this item when selecting [small] or [medium] or [large] in [Size] menu (see page 24). ] key. 38-FP0001-02 1. Select [Pip] on the Main menu and press [Menu You can see the cursor moving to the Sub menu. Size (Ex.
LCD Monitor Instructions Adjustment Procedure (Pip Menu) 3. Use [ ] and/or [ ] key to adjust. (Interval: 0~100) By pressing [ ] key, the contrast (difference between bright and dark) becomes darker. By pressing [ ] key, the contrast (difference between bright and dark) becomes lighter. 6 Adjust the color (Video signal only) You can adjust this item when selecting [small] or [medium] or [large] in [Size] menu (see page 24). 1. Select [Pip] on the Main menu and press [Menu ] key.
Adjustment for computer screen (Ex.) off small medium large Pos Advanced Source Pip Brightness auto comp 50 - Adv pip Contrast 50 - + Options Color + Utilities Tint 50 50 - Sharpness 50 - + Main menu s-video + 38-FP0001-02 Size Picture + Sub menu 2. Select [Tint] on the Sub menu with pressing [ ] or [ ] key. The selected item of [Tint] turns blue. 3. Use [ 8 ] and/or [ ] key to adjust. (Interval: 0~100) By pressing [ ] key, the skin color turns more greenish.
LCD Monitor Instructions Adjustment Procedure (Advanced Pip Menu) D. Advanced picture in picture Menu This menu can be used when inputting Composite Video or S-Video signal and also selecting [small] or [medium] or [large] in [Size] menu (see page 24). You can adjust the horizontal/vertical position for pip and select the video format if you select this menu. 1 Adjust the horizontal position 1. Select [Adv pip] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu.
Adjustment for computer screen 3. Use [ ] key to adjust. (Interval: 0~100) Press [ ] key to shift the screen to the bottom. Press [ ] key to shift the screen to the top. Select the video format 1. Select [Adv pip] on the Main menu and press [Menu 38-FP0001-02 3 ] and/or [ ] key. You can see the cursor moving to the Sub menu. (Ex.) H position 50 Picture V position 50 Advanced Pip Adv pip Options Utilities Video format Auto NTSC PAL SECAM Sub menu Main menu 2.
LCD Monitor Instructions Adjustment Procedure (Options Menu) E. Options Menu You can change the osd position, osd timeout, osd background and backlight and select portrait or landscape, language used in osd and see the resolution at the time if you select this menu. 1 Select the osd position 1. Select [Options] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. OSD (Ex.
Adjustment for computer screen 3. Use the [ ] and/or [ ] key to select [Normal] or [Rotated]. Select "Normal" to display LANDSCAPE. Select "Rotated" to display PORTRAIT. Change the osd timeout 1. Select [Options] on the Main menu and press [Menu 38-FP0001-02 3 ] key. You can see the cursor moving to the Sub menu. OSD Picture Advanced (Ex.
LCD Monitor Instructions Adjustment Procedure (Options Menu) 5 Select language used in OSD (On Screen Display) 1. Select [Options] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. OSD (Ex.) Picture Rotation Advanced Osd timeout Normal Pip Adv pip Options Utilities Osd background Language Rotated 10 seconds opaque translucent + 51 - Backlight Sub menu Main menu 2. Select [Language] on the Sub menu with pressing [ ] or [ ] key.
Adjustment for computer screen (Utilities Menu) F. Utilities Menu You can adjust the screen by Auto Adjust (Automatic Adjustment), reset the osd setting, and display the osd version if you select this menu. Automatic Adjustment (Analog mode only) 1. Select [Utilities] on the Main menu and press [Menu 38-FP0001-02 1 ] key. You can see the cursor moving to the Sub menu. Picture (Ex.
LCD Monitor Instructions Adjustment Procedure (Utilities Menu) 3 Display the osd version Select [Utilities] on the Main menu, the osd version is always displayed in [Internal Firmware] on the Sub menu. Picture (Ex.) Advanced Pip Adv pip Options Utilities Auto Adjust press to select Reset Internal Firmware Rom Version 1024 x 768 / 60 Hz Mode: 88 Sub menu Main menu 4 Display the resolution Select [Utilities] on the Main menu.
Additional Functions This is the function to reduce the monitor's power consumption, when a computer has not been used for long, even when the power to this LCD monitor is "ON". In order to activate this system, it must be connected and used with a computer that conforms to DPMS (Display Power Management Signaling) Standard of the VESA (Video Electronics Standards Association). 38-FP0001-02 Power Management System Plug and Play This monitor conforms to DDC2B (Display Data Channel 2B) standard of VESA.
Maintenance Always unplug the AC cable from the outlet before maintenance. Also unplug the signal cables from the computer. Cabinet Display Screen 37 Soak a soft cloth in water or neutral detergent, wring well, and wipe the cabinet gently. Never use solvents such as paint thinner or benzene as they will damage the surface of the cabinet. Follow the manufacturer’s directions when using chemically treated cloths. Gently blow away any dust that has adhered to the display screen.
Troubleshooting Please check the following items before requesting repair. When this LCD monitor still does not work properly after checking in following way, stop using it, turn off the power switch, unplug the power plug from the AC Outlet, and contact the store where it was purchased. In case a COMPUTER is connected, please refer to the User's Manual for this LCD monitor also.
Specifications Table of Preset Data Fifteen signal timing patterns indicated in the tables below are preset when the monitor is shipped from the factory. The timing pattern is automatically determined and displayed according to the synchronous signals of the computer being used. The monitor will use the closest timing pattern for display when a perfectly matched one is not available. No. Resolution Vertical Frequency Horizontal Frequency 1 640 x 350 dots 70 Hz 31.
Cable Pin Arrangement No. Signal name No. Signal name 6 R GND 11 No Connect G 7 G GND 12 DDC data line* B 8 B GND 13 Hor. Sync. 4 No Connect 9 No Connect 14 Vert. Sync. 5 DDC GND* 10 GND 15 1 R 2 3 No. Signal name * DDC Standard (VESA) DDC clock line* 1 6 11 5 10 15 38-FP0001-02 Analog Video Input : mini D-Sub (15pin) Cable Pin Arrangement (female) Digital Video Input : DVI-D (24pin) No. Signal name No. Signal name No. Signal name 1 T.M.D.S. Data2- 9 T.M.D.S.
Specifications Monitor Specifications 38-FP0001-02 LCD Liquid Crystal Panel Display Size Pixel Configuration Pixel Pitch Brightness Response Time Contrast Angle of Visibility TFT 39.6'' 1,280 x 768 0.6735 x 0.6735 mm 470 cd/m2 typ. Black to White: 14 ms White to Black: 8 ms Gray to Gray: 8 ms 600 : 1 typ. Up 85, Down 85, Right 85, Left 85 degrees (contrast ratio of less than 10) PC Input Vertical signal Horizontal signal Video Signal No.
Adjustment for Composite Video/S-Video/Component Video Table of contents Table of contents .................................................................................... 42 Adjustment for Composite Video / S-Video / Component Video Adjustment Items .................................................................................. 53 Mode..................................................................................................... 54 Adjustment Procedure Before Adjustment .....................
Adjustment for Composite Video/S-Video/Component Video Names and Functions (Monitor) Front View Display Screen NOTE ¡ When you move the LCD monitor, please unplug AC cables connected to AC-IN and disconnect the cables connected to the external equipment. ¡ When you carry the LCD monitor, please be careful not to shock it. To avoid damaging the LCD panel, be sure not to touch the LCD panel when carrying the monitor.
Rear View HD G/Y BNC Connector 38-FP0001-01 R/Cr VD B/Cb Ventilators Ventilators Ventilators Power Switch ( Turns the power to the monitor on and off.
Adjustment for Composite Video/S-Video/Component Video Names and Functions (Remote Controller) Operating Range (when there is no obstacle) Horizontal 45 Vertical
Standby key Standby ON/OFF. Menu key Show Main menu. Used to move cursor leftward while displaying the menu. Wide key Set the scale mode in wide. Numeric keys (see page 72) key (see page 72) Zoom out the picture. Source key Search and switch to current input signal automatically. Escape key 38-FP0001-01 Used to switch each input signal. [0], [8] and [9] keys are not used.
Adjustment for Composite Video/S-Video/Component Video Outer Dimension Ventilators VD HD/CSYNC B/Cb G/Y R/Cr IR S-VIDEO VIDEO External Control RGB 47 DVI AC-IN POWER
Ventilators Ventilators 38-FP0001-01 Ventilators 4-M6 (Depth : Min.12mm/Max.20mm) Ventilators Ventilators Mounting Area Ventilators Ventilators When you install the LCD Monitor, please take care the following: • Use the M6 screws only for installation. • The maximum length of the screw put through a hole is 20mm on the surface of a metal chassis (as shown right). Use the screw with effective length 12-20mm, if not it may damage to the LCD monitor.
Adjustment for Composite Video/S-Video/Component Video Installation Connect the Video deck, DVD player etc. Turn off the power for the monitor and AV equipment before the connection. 1 Plug the cable(s) into the connector on the monitor securely. the other end of the cable(s) into the connector on AV 2 Plug equipment. 3 Plug the AC Power Cord into the AC-IN on the monitor. 4 Plug the Power Plug into an outlet. 5 Switch on the monitor before starting up AV equipment.
Connect the Computers the cable(s) into the connector on the monitor securely and fix 1 Plug them in place with two screws (each). 2 Plug the other end of the cable(s) into the connector on a computer. 3 Plug the AC Power Cord into the AC-IN on the monitor. 4 Plug the Power Plug into an outlet. 5 Switch on the monitor before starting up a computer. External OSD Connector DVI Connector RGB Connector 38-FP0001-01 Before doing anything, make sure the Power Switch on the monitor and a computer is turned off.
Adjustment for Composite Video/S-Video/Component Video Installation How to secure the monitor on a wall Note: The following figure is only recommended. Vertical M6 bolt (4 places) UP b Depth: Min. 12mm Max. 20mm Bracket (not included) Side view of the monitor Horizontal Rear view of the monitor M6 bolt (4 places) UP b Depth: Min. 12mm Max. 20mm Bracket (not included) Side view of the monitor Rear view of the monitor Caution 51 Never cover the rear ventilators with cloth or something.
How to Use Use this monitor with following procedure. Watch Video/DVD Connect video cable from Video deck or DVD player to the monitor. Use Computers Connect video cable from computer to this monitor. a a Adjust the Screen (see page 53). If adjustment not required or skip Adjust the Screen (see page 12). a a If adjustment not required or skip a *Search the input signal automatically. Choose "Analog" or "Digital" (see page 54).
Adjustment for Composite Video/S-Video/Component Video Adjustment Items Please follow the OSD (On Screen Display) menu to adjust screen settings using Remote Controller (see page 45).
Mode You can change or indicate the signal input type following the steps. Change or indicate the input signal 1. While the OSD (On Screen Display) is not displayed, it is possible to change or indicate the current mode. Press [Source] key to indicate the current mode in the lower right corner of the screen. (Ex.) 2. While displaying the current mode, press [Source] key again.
Adjustment for Composite Video/S-Video/Component Video Adjustment Procedure Before Adjustment The signal timing for a computer which this LCD monitor supports is listed in "Table of Preset Data" on Page 39, the recommended value of Vertical Frequency for this model is 60Hz. (Unlike CRT Monitors, the display becomes stable when Vertical Frequency is low.) It is recommend to set Vertical Frequency of a computer connected at 60Hz by "refresh rate setting" before starting adjustment procedure.
Move the cursor to Sub menu After Main menu item is selected, press [Menu ･Press [ Menu] key to return to Main menu from Sub menu. (Ex.) Brightness 25 - + Picture Contrast + Advanced H position 50 50 - Pip Adv pip Options Utilities V position 50 - + 15 1056 - + Main menu 5 Phase Frequency + + Scaling Wide Sub menu Select item of Sub menu Press [ ] or [ ] key as well as the Main menu item selection. (Ex.
Adjustment for Composite Video/S-Video/Component Video Adjustment Procedure 2. For the adjustment item like "brightness", press [−] or [＋] key to change levels of selected item. (Ex.) Brightness 25 - + Picture Contrast + Advanced H position 50 50 - Pip Adv pip Options Utilities V position 50 - + 15 1056 - + Main menu 7 Phase Frequency Scaling + + Wide Sub menu Adjustment or Setting For each item selected, the adjustment/setting has been made by pressing [ ] and/or [ ] key.
(Picture Menu) A. Picture Menu The adjustment of brightness, contrast, horizontal position, vertical position, color, tint, sharpness and scaling for the picture are available. 1 Adjust the brightness 1. Select [Picture] on the Main menu and press [Menu ] key. (Ex.) Brightness 50 - + Picture Contrast 50 - + Advanced H position 50 - + Video Options V position 50 - + Color 50 - + Utilities Tint 50 - + Main menu Sharpness 1 2 3 4 5 6 7 8 Scaling Wide Sub menu 2.
Adjustment for Composite Video/S-Video/Component Video Adjustment Procedure (Picture Menu) 3. Use [ ] and/or [ By pressing [ ] key to adjust. (Interval: 0~100) ] key, the contrast (difference between bright and dark) becomes lighter. By pressing [ ] key, the contrast (difference between bright and dark) becomes darker. 3 Adjust the horizontal position 1. Select [Picture] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. (Ex.
2. Select [V position] on the Sub menu with pressing [ ] or [ ] key. The selected item of [V position] turns blue. 3. Use [ 5 ] and/or [ ] key to adjust. (Interval: 0~100) By press [ ] key to shift the screen to the top. By press [ ] key to shift the screen to the bottom. Adjust the color 1. Select [Picture] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu.
Adjustment for Composite Video/S-Video/Component Video Adjustment Procedure (Picture Menu) 2. Select [Tint] on the Sub menu with pressing [ ] or [ ] key. The selected item of [Tint] turns blue. 3. Use [ 7 ] and/or [ ] key to adjust. (Interval: 0~100) By pressing [ ] key, the skin color becomes more greenish. By pressing [ ] key, the skin color becomes more purplish. Adjust the sharpness 1. Select [Picture] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu.
Adjust the scaling 1. Select [Picture] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. (Ex.) Brightness 50 - + Picture Contrast + Advanced H position 50 50 - Video Options V position + Color 50 50 - Utilities Tint 50 - + Main menu Sharpness + + 1 2 3 4 5 6 7 8 Scaling Wide Sub menu 2. Select [Scaling] on the Sub menu with pressing [ ] or [ ] key. The selected item of [Scaling] turns blue. 3.
Adjustment for Composite Video/S-Video/Component Video Adjustment Procedure (Advanced Menu) B. Advanced Menu You can adjust the color temperature for the screen manually if you select this menu. Three preset values of color temperature are set up at the time of factory shipments. Besides, you can set your preferable values. 1 Adjust the color temperature (Preset) 1. Select [Advanced] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu.
Adjust the color temperature (User) If you wish to set user settings of color temperature, follow the steps. (Ex.) In case adjusting the [User red], [User green] and [User blue] in sequence. 1. Select [Advanced] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. Color User red Picture Advanced Video Options (Ex.) Warm Neutral Cold user - + User green - + User blue - + Sub menu Utilities Main menu 2.
Adjustment for Composite Video/S-Video/Component Video Adjustment Procedure (Video Menu) C. Video Menu When video signal is input, you can select the video format (NTSC/PAL/SECAM) manually. 1 Select the video format 1. Select [Video] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. The selected item of [Video format] turns blue. Video format Auto NTSC PAL SECAM Picture Sub menu Advanced (Ex.) Video Options Utilities Main menu 2.
(Options Menu) D. Options Menu You can change the osd position, osd timeout, osd background and backlight and select portrait or landscape, language used in osd and see the resolution at the time if you select this menu. 1 Select the osd position 1. Select [Options] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu.
Adjustment for Composite Video/S-Video/Component Video Adjustment Procedure (Options Menu) 3. Use the [ ] and/or [ ] key to select [Normal] or [Rotated]. Select "Normal" to display LANDSCAPE. Select "Rotated" to display PORTRAIT. 3 Change the osd timeout 1. Select [Options] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. OSD (Ex.
5 Select language used in OSD (On Screen Display) 1. Select [Options] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. OSD (Ex.) Picture Rotation Advanced Video Options Osd timeout Osd background Language Utilities Backlight Normal Rotated 10 seconds opaque translucent + 51 - Sub menu Main menu 2. Select [Language] on the Sub menu with pressing [ ] or [ ] key. 3. Use the [ ] and/or [ When pressing the [ ] key to select the language.
Adjustment for Composite Video/S-Video/Component Video Adjustment Procedure (Utilities Menu) E. Utilities Menu You can reset the osd setting and display the osd version if you select this menu. 1 Delete the data saved at the current display mode 1. Select [Utilities] on the Main menu and press [Menu ] key. You can see the cursor moving to the Sub menu. Picture (Ex.) Advanced Video Options Reset Internal Firmware Rom Version Sub menu Utilities Main menu 2.
Additional Functions Shortcut Menu You can shortcut to adjust the brightness and contrast of the whole screen and size of picture in picture. When the OSD (On Screen Display) is not displayed, it is possible to display the Shortcut Menu. The adjustment flow is described in below: 1 Display the Shortcut Menu 1. While the OSD (On Screen Display) is not displayed, it is possible to display the Shortcut Menu. Press [Quick Menu] key. The shortcut menu is displayed. - + 2.
Adjustment for Composite Video/S-Video/Component Video Additional Functions 2. Use [ ] and/or [ By pressing [ ] key to adjust. (Interval: 0~100) ] key, the contrast (difference between bright and dark) becomes darker. By pressing [ ] key, the contrast (difference between bright and dark) becomes lighter. 4 Select the size of pip (picture in picture) 1. Use [Quick Menu] key to select [Pip enable] menu. Pip enable (Ex.) off S 2. Use [ ] and/or [ M L ] key to select the size of pip.
2. To search other input signal connected to the monitor, press [Source] key of remote control again while the input signal type is displayed. ･ The searching order of other input signal is as follows. [Analog RGB1] → [Analog RGB2] → [Digital RGB] → [Composite Video] → [S-Video] → [Component Video] → [RGB+C Sync] ･ Every time the input signal is searched, display the searched and stop searching picture. ･ "No input signal. Going to Sleep." is displayed when there is no other input signal detected.
Adjustment for Composite Video/S-Video/Component Video Additional Functions Power Management System This is the function to reduce the monitor's power consumption, when a computer has not been used for long, even when the power to this LCD monitor is "ON". In order to activate this system, it must be connected and used with a computer that conforms to DPMS (Display Power Management Signaling) Standard of the VESA (Video Electronics Standards Association).
Troubleshooting Fault Finding Fault Finding Please check the following items before requesting repair. When this LCD monitor still does not work properly after checking in following way, stop using it, turn off the power switch, unplug the power plug from the AC Outlet, and contact the store where it was purchased. In case a COMPUTER is connected, please refer to the User's Manual for this LCD monitor also.
Specifications Monitor Specifications LCD Liquid Crystal Panel Display Size Pixel Configuration Pixel Pitch Brightness Response Time Contrast Angle of Visibility TFT 39.6'' 1,280 x 768 0.6735 x 0.6735 mm 470 cd/m2 typ. Black to White: 14 ms White to Black: 8 ms Gray to Gray: 8 ms 600 : 1 typ. Up 85, Down 85, Right 85, Left 85 degrees (contrast ratio of less than 10) 38-FP0001-01 PC Input Vertical signal Horizontal signal Video Signal No.
Federal Communications Commission (FCC) Statement This device has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.
77
78
CHRISTIE DIGITAL SYSTEMS, Inc. 809 Wellington Street North Kitchener, Ontario Canada N2G 4Y7 Telephone (519) 744-8005 North America call toll-free 1-800-265-2171 (sales) Fax (519) 749-3136 CHRISTIE DIGITAL SYSTEMS, Inc. 10550 Camden Drive Cypress, CA 90630 USA Telephone (714) 236-8610 Fax (714) 503-3385 Toll Free 1-800-407-7727 Toll Free 1-800-333-3816 CHRISTIE DIGITAL SYSTEMS, Inc. ViewPoint 200 Ashville Way Workingham, Berkshire, U.K.
