Christie Vive Audio CDA2/CDA3 Amplifiers User Manual 020-100355-02
Christie Vive Audio CDA2/CDA3 Amplifiers User Manual 020-100355-02
NOTICES COPYRIGHT AND TRADEMARKS Copyright © 2013 Christie Digital Systems USA Inc. All rights reserved. All brand names and product names are trademarks, registered trademarks or trade names of their respective holders. GENERAL Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in this document. Christie reserves the right to make changes to specifications at any time without notice.
이 기기는 업무용(A급)으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며, 가정 외의 지역에서 사용하는 것을 목적으로 합니다. ENVIRONMENTAL The product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from regular waste. Please dispose of the product appropriately and according to local regulations.
Table of Contents Important Safety Information ....................................................................................... 1 Introduction .................................................................................................................... 3 Overview ...........................................................................................................................................................................3 Features ....................................................
Important Safety Information Read this information thoroughly and completely before installing or operating Christie Vive Audio CDA2/CDA3 Professional Power Amplifiers. • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. • Clean only with a dry cloth. • Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
• The power switch does not break both sides of the primary mains. Hazardous energy can be present inside the chassis when the power switch is in the off position. The mains plug or appliance coupler is used as the disconnect device. The disconnect device shall remain readily operable. • Exposure to extremely high noise levels may cause permanent hearing loss.
Introduction This user manual provides data about the Christie Vive Audio CDA2/CDA3 Professional Power Amplifiers controls, installation, and specifications. Overview Christie Vive Audio CDA2/CDA3 Professional Power Amplifiers utilize an advanced design that reduces the weight of the amplifier significantly while increasing output power, reliability, and thermal efficiency.
What’s In the Box? Part Number Quantity Description 1 Christie Vive Audio CDA2 Professional Amplifier 100V -or- 145-005106-XX Christie Vive Audio CDA2 Professional Amplifier 120V -or- 145-001102-XX Christie Vive Audio CDA2 Professional Amplifier 230V -or- 145-009100-01 Christie Vive Audio CDA3 Professional Amplifier 100V -or- 145-006107-01 Christie Vive Audio CDA3 Professional Amplifier 120V -or- 145-002103-01 1 Christie Vive Audio CDA3 Professional Amplifier 230V 145-010102-01 Power C
B Indicators Indicates the operating status of each of the channels and warns of possible malfunction. There are 5 indicators for each channel: • ACL (automatic clip limiting) - indicates clipping. If the light is flashing quickly and intermittently, the channel is at the clip threshold. Gain reduction is automatically employed to prevent severely clipped waveforms from reaching the loudspeakers. • SIG (signal) - indicates that an output signal of 4 volts RMS or more (0.
C Inputs • CH. B - allows a twist lock connector to be connected to the channel B output. • BRIDGE - allows for a twist lock connector to be connected to the bridged amplifier output. • CH. A - allows a 2-pole or 4-pole twist lock connector to be connected to the channel A output. Connecting a 4-pole twist lock connector provides the outputs of both channels A and B on the corresponding poles of the 4-pole connector. • Provides the connecting inputs and input controls.
Installation This section provides information and procedures for installing and connecting the Christie Vive Audio CDA2/CDA3 Professional Power Amplifiers. Install the CDA2 or CDA3 An incorrect power setup creates a fire and shock hazard. Do not attempt operation unless the power cord, power socket, and power plug meet the appropriate local rating standards. Have a certified electrician install a permanent single-phase connection from the amplifier to the AC supply for correct installation.
Stereo Mode Connections A 3-pin XLR, or 6.3 mm (1/4 in.) phono jacks connected to the CH. A and CH. B INPUTS B Input selector set to STEREO B Input selector set to PARALLEL Parallel Mode Connections A 3-pin XLR, or 6.3 mm (1/4 in.) phono jacks connected to the CH. A INPUTS Output Connections Always turn off and disconnect the Christie Vive Audio CDA2/CDA3 Professional Power Amplifiers from power before making audio connections. Failure to comply may result in equipment or property damage.
This section describes the output connections of the Christie Vive Audio CDA2/CDA3 Professional Power Amplifiers. Stereo Mode Connections A NL2 twist-lock connectors connected to CH. A and CH. B OUTPUTS B Input selector set to STEREO Biamp Mode Connections Christie Vive Audio CDA2/CDA3 Amplifiers User Manual 020-100355-02 Rev.
A NL4 twist-lock connector connected to CH. A. OUTPUTS B Input selector set to STEREO B 3-pin XLR, or 6.3 mm (1/4 in.) phono jacks connected to the CH. A INPUTS Bridge Mode Connections A NL2 twist-lock connector connected to the BRIDGE OUTPUTS C Input selector set to BRIDGE Operation Turn the Power On 10 • Use only the AC power cord that is provided. DO NOT attempt operation if the AC supply is not within the specified voltage and power range.
comply could result in death or serious injury. • Only qualified service technicians are permitted to open enclosures and only if the amplifier is disconnected from AC power. Failure to comply could result in in death or serious injury. • DO NOT allow anything to rest on the power cord. Locate the amplifier where the cord cannot be damaged by persons walking on it or objects rolling over it. Never operate the amplifier if the power cable appears damaged in any way.
Troubleshooting This section provides basic Christie Vive Audio CDA2/CDA3 Professional Power Amplifiers troubleshooting information. Do not service the amplifier yourself. Contact a qualified service technician. Problem Resolution The amplifier power will not turn on. • Verify that the amplifier is receiving power. Plug the amplifier into the AC mains. Connect the IEC line cord to the AC power inlet on the rear panel of the amplifier. • Verify that the circuit breaker for the mains circuit is open.
they are complete and wired correctly. Verify the polarity of each connection. There is output from one channel, but not from the other channel. • Verify that the attenuators are turned up for both channels. • Check all connections between the amplifier and loudspeakers. Make sure that the twist lock connectors are fully-inserted and seated. The connectors must be inserted and turned 1/4” clockwise until they lock in position.
Specifications This section provides Christie Vive Audio CDA2/CDA3 Professional Power Amplifiers specifications.
Power Specification1 CDA2 Value CDA3 Values Input power requirement 120V~; 60Hz; 320W, Class I 120V~; 60Hz; 495W, Class I 220-240V~; 50/60Hz; 320W, Class I 220-240V~; 50/60Hz; 495W, Class I 100V~; 60Hz; 320W, Class I 100V~; 60Hz; 495W, Class I Rated power Bridged at 4 ohms Bridged at 8 ohms 2 chs x 2 ohms 2,100 watts 20 ms repetitive burst/ 3,640 watts 20ms repetitive burst/ 1,950 watts @ 1kHz 1% THD 3,000 watts 1% THD @ 1kHz N/A 2,000 watts 20ms repetitive burst/ 1,550 watts 0.
Block Diagram Physical Specification CDA2 Value CDA3 Values Enclosure 0.157 cm (0.062 in.) aluminum 18ga. galvanized steel Dimensions (H x W x D) 8.9 cm x 48.3 cm x 26.7 cm (3.5 in.) x (19 in.) x (10.5 in.) 8.9 cm x 48.3 cm x 26.7 cm + 0.15 cm for handles Weight (net)1 4.94 kg (10.90 lb) 5.54 kg (12.2 lb) Weight (gross)2 6.02 kg (13.3 lb) 6.30 kg (13.9 lb) 1. Net weight excludes the power cord. 2. Gross weight excludes the power cord.
*000-104317-01* ASSY TECH DOCS VIVE CDA2-CDA3