E Series DHD675-E/DWU675-E/DHD775-E/DWU775-E USER MANUAL 020-000515-01
Addendum The CD included with this printed manual contains an electronic copy in English. Please read all instructions before using or servicing this product. 㓚␛₼▔⚺䤓⏘䥧᧨サ㦘䧏₼㠖䤓䟄⓾㦻᧨∎䞷㒥冃≽㦻ℶ❐ⓜ᧨庆Ⅳ兕㩴梔㓏㦘䤓㖖䯉ᇭ Le DC fourni avec ce manuel imprimé contient une copie électronique en français. S'il vous plaît lire toutes les instructions avant d'utiliser ou de réparer ce produit. Il CD fornito con il manuale stampato contiene una copia elettronica in lingua italiano.
NOTICES COPYRIGHT AND TRADEMARKS © 2012 Christie Digital Systems USA, Inc. All rights reserved. All brand names and product names are trademarks, registered trademarks or trade names of their respective holders. REGULATORY The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated in a commercial environment.
GENERAL Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in this document. Christie reserves the right to make changes to specifications at any time without notice. Performance specifications are typical, but may vary depending on conditions beyond Christie's control such as maintenance of the product in proper working conditions.
Table of Contents 1. SAFETY 2. INTRODUCTION 2.1 2.2 2.3 2.4 2.5 Projector Components...................................................................................................2-1 Built-in Keypad..............................................................................................................2-3 Input/Output (I/O) Panel................................................................................................2-4 Remote Control.........................................................
Table of Contents 5. TROUBLESHOOTING 6. SPECIFICATIONS 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 ii Inputs.............................................................................................................................6-1 PIP/PBP Compatibility...................................................................................................6-2 Key Features.................................................................................................................6-3 List of Components..........
Section 1: Safety 1. SAFETY Read through this document in its entirety and understand all warnings and precautions before attempting to operate the projector. WARNING yy Do not look into the projector lens when the lamp is on. The bright light may result in permanent eye damage. yy To reduce the risk of fire or electric shock, do not expose this projector to rain or moisture. yy Do not open or disassemble the projector as this may cause electric shock.
Section 1: Safety yy Always power down the projector and disconnect all power sources before servicing or cleaning. yy Use a soft cloth moistened with a mild detergent to clean the display housing. yy Disconnect the power plug from the AC outlet if the product is not being used for an extended period of time. yy Operate the projector under the following conditions: -- Operating temperature range: 5°C to 35°C -- Storage temperature range: -10°C to 60°C -- Humidity range: 5% to 80 % RH (Max.
Section 2: Introduction 2. INTRODUCTION The product specified in this document is a high brightness, high-resolution video/graphics 1-chip mercury lamp based projector. The projector is available in HD and WUXGA resolutions. The projector utilizes Digital Light Processing (DLP®) technology from Texas Instruments. It is primarily designed for fixed installation markets. 2.1 Projector Components Front View 1 2 3 4 5 Rear View 6 7 8 9 10 E Series User Manual 020-000515-01 Rev.
Section 2: Introduction Ind. 2-2 Part Name Description 1 Lens door Use the lens door to access the lens module. 2 Front IR Sensor Receives signals from the IR remote. Keep the signal path to the sensor unobstructed for uninterrupted communication with the projector. 3 Projection Lens Allows automated lens control and adjustment: vertical and horizontal offsets, zoom and focus. 4 Cooling Air Vents Keep these vents unobstructed to prevent the projector from overheating.
Section 2: Introduction 2.2 Built-in Keypad 1 6 2 7 3 8 4 9 5 10 Ind. Key Name Description 1 Power Turn the projector on or off.
Section 2: Introduction 2.3 Input/Output (I/O) Panel Ind. 2-4 1 2 10 11 3 4 5 12 Connector Name 6 13 Ind. 7 14 8 15 9 16 Connector Name 17 18 Ind. 19 20 Connector Name 1 S-Video 2 CVBS 3 Red/Pr 4 Blue/Pb 5 Green/Y 6 RS232 IN 7 Mini USB 8 USB 9 Ethernet 10 Remote 11 Display Port 12 VGA-OUT 13 VGA-IN 14 HDMI-1 15 HDMI-2 16 R 17 G 18 B 19 H/C 20 V E Series User Manual 020-000515-01 Rev.
Section 2: Introduction 2.4 Remote Control 1 2 16 3 17 4 18 5 19 6 20 21 7 22 8 9 23 10 24 11 12 13 E Series User Manual 020-000515-01 Rev.
Section 2: Introduction Ind.
Section 2: Introduction 2.5 LED Status Indicators The LED status indicators are located on the rear of the projector. yy LAMP 1 LED LED Status Red (short blink) Projector State Failed to strike lamp after 5 attempts (strike attempts will stop). Lamp has unexpectedly shut down (system goes into cool down state). Yellow (no blink) Lamp time has expired and lamp should be replaced. (projector also begins to display the replace lamp On Screen Display message at startup).
Section 2: Introduction yy STATUS LED LED Status Projector State Off Projector is in OFF state (without AC plug in) Yellow (no blink) Projector is in standby mode (AC plug in) Yellow long blink Projector is in startup state Yellow long blink Projector is in cool down state Flashing Green/ Yellow Projector is in flash update state Flashing Red Fan failure Red (no blink) Over-temperature Green (blink very quickly) Projector communications (Read/Write EEPROM) Green (no blink) Projector is po
Section 3: Installation 3. INSTALLATION 3.1 Connect to Computer Desktop Laptop MOLEX 9 1 2 3 4 6 7 8 5 molex Ind. Connector Name Ind. Connector Name Ind. Connector Name 1 VGA out Cable 2 VGA in Cable 3 RS232 Cable 4 Mini USB to USB A Type Cable 5 WiFi USB Dongle or thumb drive 6 Network Cable 7 HDMI to DVI Cable 8 Power Cord 9 Displayport Cable NOTE: The diagram shows the cables/connectors that may be used to connect to various devices.
Section 3: Installation 3.2 Connect to Video Equipment DVD player Component video output equipment Video cassette recorder 6 4 1 2 3 8 4 9 7 5 Ind. Connector Name Ind. Connector Name Ind.
Section 3: Installation 3.3 Turn the Projector On 111 Ensure that the power cord and signal cable are securely connected. The Power button on the built in keypad is illuminated. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 222 Turn on the lamp by pressing “ ” on the remote control or press “ ” on 3 4 5STATUS 6 7 8 9 10LED is yellow and LAMP LED is green the built-in keypad.1 2 The with a long blink. 11 12 13 14 15 16 17 18 19 20 The startup screen displays in approximately 10 seconds.
Section 3: Installation 3.5 Adjust the Projector Position When you select a position for the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Follow these general guidelines: yy Position the projector on a flat surface at a right angle to the screen. The projector (with the standard lens) must be at least 3 feet (0.9m) from the projection screen.
Section 3: Installation 3.6 Calculate Lens Offset yy The vertical image offset (shift) ranges for the projector are +120%/-40% (WUXGA) and +134%/-40% (HD). Offset is +720 pixels for both WUXGA and HD. The horizontal image offset is +/-20% (+/- 192 pixels). NOTE: The 0.8:1 lens is the only exception and must be used on axis. yy The method for calculating lens offset complies with Industry standards.
Section 3: Installation Vertical Image Offset: 120% Offset (WUXGA) Image has been offset 720 pixels above lens center, so the center of the image is now 720 pixels above where the center of the image was at 0% offset (or lens center). The offset is +720/600 * 100% = +120%. 720 pixels of shift above lens center.
Section 3: Installation HD Projectors: Vertical Image Offset: 0% Offset (HD) No offset is applied - 0% offset. Half of the image appears above lens center and half of the image appears below lens center. 540 pixels above lens center. Lens center 540 pixels below lens center. Vertical Image Offset: 134% Offset (HD) Image has been offset 720 pixels above lens center, so the center of the image is now 720 pixels above where the center of the image was at 0% offset (or lens center).
Section 3: Installation Vertical Image Offset: -40% Offset (HD) Image has been offset 216 pixels below lens center, so the image has an offset of -216/540 * 100% = -40% 216 pixels of shift below lens center. Lens center Total of 756 pixels (540+216) of display are below lens center. Horizontal Image Offset: +/-20% Offset 1920 pixels +192 pixels Lens center -192 pixels Image has been offset 192 pixels left or right of lens center.
Section 3: Installation 3.7 Removing and Installing the Lens When handling the projector after lens installation, make sure the front lens cap is placed on the lens to protect the lens surface from potential damage. When carrying or moving the projector, do not handle by the lens. This may damage the lens, the chassis or other mechanical parts within the projector. 111 Center the lens: Ensure that the lens is at or near its center position.
Section 3: Installation 3.8 Ceiling Mount Installation The projector can be inverted and suspended from the ceiling using a specially designed ceiling mount fixture. For more information, contact your dealer. yy Use only the Christie approved ceiling mount kit (133-106108-02) designed for your projector. yy When not mounted properly, the projector may fall, causing hazards or injury.
Section 3: Installation 3.9 Stacking Installation 3.9.1 Adapter Plate Installation When stacking E Series projectors, an adapter plate is required to install the E Series unit into the stacking frame. 111 Turn the projector OFF and disconnect the AC power cord after the cooling fans have stopped. 222 Place the projector top-side down on a clean and flat surface. 333 Line up the mounting holes of the adapter plate (133-107109-02) with the mounting holes on the baseplate of the projector.
Section 3: Installation Install the adapter plate on the E Series projector (described in 3.9.1) before mounting to the stacking frame. 111 Make sure the pitch is to its maximum, prior to placing the projector from the front. 222 Place the projector into the stacking frame. NOTE: There are two ways of placing the projector into the stacking frame: from the top or from the front. 333 Make sure the bottom base plate of the frame is aligned with the projector.
Section 3: Installation 222 Insert the locking pin through the holes in the stacking legs. Make sure each pin is fully inserted. NOTE: The steel ball on the end of the pin keeps the pin from releasing inadvertently. Stacking Leg Hole Pin Inserted Press botton to remove or install the pin Pin Steel Ball 333 When required, repeat steps 1 and 2 for the third projector in the stack. 3.9.
Section 4: Operation 4. OPERATION The projector has multilingual On-Screen Display (OSD) menus that allow you to make image adjustments and change a variety of settings. •• Most of the projector controls are accessed from within the projector menu system. There are several groups of related functions, with each group selectable from the Main menu as shown below. Press the MENU button on the remote control or on the built-in keypad on the rear of the projector to display the main menu.
Section 4: Operation 4.1 Size and Position Menu Size Presets Display an image with the detected size, or resize the image by maximizing either the height, width or both, or resize to the maximum size possible while keeping the original aspect ratio. yy Auto: Display with the detected size. Native: Display in its native resolution. 4:3: Retain 4:3 aspect ratio. Letterbox: Display with the black borders on the top and bottom. Full Size: Fill the screen (regardless of the source).
Section 4: Operation Pixel Phase Analog RGB signals only. Adjust pixel phase when the image still shows shimmer or noise after pixel tracking is optimized. Pixel phase can adjust the phase of the pixel-sampling clock relative to the incoming signal. Horz Position Move the image right or left within the area of available pixels. Vert Position Move the image up or down within the area of available pixels. Digital Horz Zoom Change the size of projector's display area horizontally.
Section 4: Operation yy Off: No Geometric correction is applied to the image. yy Horz Keystone: Adjust the keystone horizontally and make a more square image. Horizontal keystone is used to correct a keystoned image shape in which the left and right borders of the image are unequal in length, and the top and bottom are slanted to one of the sides. This is intended for use with horizontally on-axis applications.
Section 4: Operation yy Pincushion/Barrel: Allow for correction for slight curved distortion from the lens or projection surface. 8% 4% 9% 9% yy 4-Corner: Allow the image to be squeezed to fit an area defined by moving each of the four corners’ x and y position. 1 2 8% Ind. 8% 8 3 Description 1 Top Left Horz adjust. 2 Top Right Horz adjust. 7% 7% 3 Top Right Vert adjust. 7% 7% 4 Bottom Right Vert adjust. 5 Bottom Right Horz adjust. 6 Bottom Left Horz adjust.
Section 4: Operation yy Rotation: Allow an image to be rotated – most commonly to level the image. While the image is rotated, the software can crop any content that begins to fall off the panel. The function will not automatically scale the image down to prevent cropping. If scaling is required, the digital zoom function can be used, independently of the rotation function. ±8° Auto Image Force the projector to reacquire and lock to the input signal. This is useful when signal quality is marginal.
Section 4: Operation 4.2 Image Settings Menu Brightness Adjust the intensity of the image. Contrast Adjust the degree of difference between the lightest and darkest parts of the picture and change the amount of black and white in the image. Color Space Select a color space that has been specifically tuned for the input signal. Useful only for analog signals and certain digital sources. Detail Select the edge clarity of the image. Video Options This function is used with video sources only.
Section 4: Operation yy Video Black Level: Analyze the current input image and calculate an offset value which is then added to the analog to digital converter black level value. This ensures optimum black level for each analog source. yy Detect Film: Control film mode detection and determine whether the original source of the input video was film or video. yy Closed Captions: Control closed caption display while audio is not muted.
Section 4: Operation yy White Peaking: (video source only) Increase the brightness of whites that are near 100%. yy Color Temperature: Change the intensity of the colors. Select a listed relative warmth value. yy Edge Enhancement: Apply the edge enhancement process. E Series User Manual 020-000515-01 Rev.
Section 4: Operation 4.3 Configuration Menu Language Allows you to select an available language for the OSD display, from English, French, German, Italian, Spanish, Chinese(simplified), Japanese, Korean, and Russian. Lens Settings yy Focus and Zoom: Adjust the focus and zoom the image in or out. yy Lens Shift: Shift the lens up and down or left and right. yy Lock Lens Motors: Select this function to prevent all lens motors from moving.
Section 4: Operation Menu Preferences yy yy yy yy Menu Horz Position: Change the horizontal position of the OSD. Menu Vert Position: Change the vertical position of the OSD. Show Messages: Display status messages on the screen. Menu Transparency: Change OSD menu background to be transparent. NOTE: As the value increases, more of the image behind the menu is visible. yy Splash Screen: Choose which splash screen is to be used.
Section 4: Operation yy Baud Rate: Select the serial port and baud rate. yy Serial Port Echo: Control whether the serial port echoes characters. yy Projector Address: Set the projector address (0-9). The projector will respond to IR remotes set either at the same address as the projector or to IR remotes set to address 0. Image Blending Adjust blend widths and settings to left, right, top and/or bottom sides to create a seamless multi-projector stitched image.
Section 4: Operation Color Matching You may require a unique color gamut (range) for a single projector or application, or you may need to precisely match colors across multiple adjacent displays. Use Color Matching by Meter Adjustment or by Manual Adjustment to define the precise hue of each primary color component (red, green, blue and white). The x/y coordinates for each color define its location on the standard CIE chromaticity graph.
Section 4: Operation Green Measured Data Target Data Red Blue yy Manual Adjustment 111 Adjust color slide bars and judge image color by eye or meter. A userdefined color “adjustment” can be applied. 222 Use this submenu if you do not have specific color coordinates in mind and will judge color performance by eye or meter. As for Meter Adjustment, each color control actually defines new x/y coordinates for that color and changes its hue.
Section 4: Operation adjusted to optimize picture quality. yy Color wheel Index (3x): Set Color wheel index to Speed 3X. This setting only needs to be used when the Main Board is changed, and should be adjusted to optimize picture quality. yy Error log: Show the projector error log for debug. yy Mode Adjustment: Fine tune the H and V start position for a signal in the EDID timing table and record the values in the system to override the timing table.
Section 4: Operation 4.4 Lamp Menu Lamp Mode Select Constant Power or Constant Intensity mode. Constant Power Set the value of the lamp power (in Watts). Constant Intensity Set the value for the Constant Intensity to maintain constant brightness. A light sensor is used to monitor the light level and will apply more power as the lamp brightness decays naturally over time until it reaches maximum power. The light sensor needs to be calibrated when you replace a lamp or "Reset Lamp Hours".
Section 4: Operation power-up, or after a set number of hours. Lamp Auto Switch Time Set the number of hours for Lamp Auto Switch. For example: 111 Lamp conditions: lamp 1 = 50 hours, lamp 2 = 60 hours. 222 Set the current lamp to lamp 1 - the lamp with the lower lamp hour usage. 333 Set the Lamp Auto Switch to After (N) hours and the Lamp Auto Switch Time to 100 hours. 444 When lamp 1 reaches 150 hours, projector will auto switch to lamp 2.
Section 4: Operation 4.5 Status Menu The read-only Status menu lists a variety of details about the standard and optional components currently detected in the projector. 4-18 E Series User Manual 020-000515-01 Rev.
Section 4: Operation 4.6 Input Switching & PIP Menu NOTE: Reference the compatibility table found in Section 6.2. Main Input From the list of active inputs, select one to be used as the main image. PIP/PBP Input From the list of active inputs, select one to be used as the PIP/PBP. PIP/PBP Enable Toggle between displaying two sources at once (Main and PIP/PBP images) or one source only. The check box turns the PIP/PBP source ON and OFF.
Section 4: Operation NOTE: PIP/PBP layout and size table as described below. P : indicates primary source region (lighter color). * : Both source regions are the same size. PIP/PBP Layout PBP, Main left PBP, Main Top PIP/PBP Size Small PIP-Bottom Right PIP-Bottom Left PIP-Top Left PIP-Top Right * P P P Large P P P PBP, Main Right PBP, Main Bottom Medium P P * P P P P P P P P P P P P P P P P * * Timing Detection Select timing detection mode to wide or normal.
Section 4: Operation Input Key Use it to list all of the sources or change the sources. 4.7 Language Menu Allows you to select an available language for the OSD display. 4.8 Test Pattern Menu Choose the desired internal test pattern to display, or select OFF to turn off a test pattern. yy yy yy yy yy yy OFF Black White Checkerboard Grid Color Bars E Series User Manual 020-000515-01 Rev.
Section 4: Operation 4.9 Web User Interface 4.9.1 Logging On Open your web browser and type the IP address (in the address bar) assigned to your projector. 1 Select the log in level from the Access type drop-down list 2 Enter the Password in the Password field 3 Select the appropriate language from the Language drop-down list. 4 Click the Press login button. The Main window appears. 4.9.
Section 4: Operation yy Projector Information Panel Check the projector information for power status, Pic mute status, OSD status, IP address and Mac address. Switch Panel Switch the on/off status of power, Pic mute, and OSD. 4.9.3 Main Tabbed Page – Status isplay the current status of lamp info, cooling (fans), version numbers and D signal (source) information 4.9.4 Main Tabbed Page – Lens Control the focus, lens shift and zoom adjustments for the lens. E Series User Manual 020-000515-01 Rev.
Section 4: Operation 4.9.5 Network SettingsPage yy Restart Network -- Execute a network restart. This will not change any of the network settings. yy Network Factory Reset Execute a network factory reset. Network settings will be reset to the following default values: -- Projector Name = Christie@ + Serial Number -- Show Network Messages = ON -- LAN Settings: -- Manual -- IP Address = 192.168.0.100 -- Subnet Mask = 255.255.255.0 -- Default Gateway = 192.168.0.
Section 4: Operation -- Start IP = 192.168.1.100 -- End IP = 192.168.1.120 -- Subnet Mask = 255.255.255.0 -- Default Gateway = 192.168.1.100 -- SNMP Settings: -- SNMP Read Communication = private -- Trap IP Address = 0.0.0.0 -- SMTP IP Address = 0.0.0.
Section 4: Operation -- SNMP Location (default setting: blank) – This field can be used as a description to where a projector is located in a building. SNMP emails sent will specify this location. -- Trap IP Address (default setting: 0.0.0.0) – This field must be filled in to receive Traps from the projector. The Trap IP Address should be filled in with the IP Address of the computer on which you would like to view received traps.
Section 4: Operation 4.9.7 Administrator Page Add or delete a user or change password 4.9.8 About Page yy Version Tab View the main firmware version, network firmware version, projector model name, and projector serial number. yy License Tab The license information of the computer program is displayed. E Series User Manual 020-000515-01 Rev.
Section 4: Operation 4.10 Christie Presenter The Christie Presenter application allows a remote desktop from a host PC to be displayed on the network display through Ethernet, USB, or wireless transports. It can adapt to different network settings (DHCP, fixed IP, and direct link by USB/Ethernet cable). Christie Presenter can be downloaded from the Christie website or from the web page of the projector. 4.10.
Section 4: Operation `` Power on the Projector. `` Obtain the WiFi Password from the OSD menu Main Menu > Configuration > Communications > WLAN `` Connect your PC device to the wireless SSID for the selected projector . Example: “Christie@0112000123”. `` Enter the password obtained from the OSD WLAN menu. E Series User Manual 020-000515-01 Rev.
Section 4: Operation 4.10.2 Install Christie Presenter software 111 Use a web browser to connect to the projector’s network address (Default address 192.168.1.100) 222 Download and install the Christie Presenter Software 333 Configure the Christie Presenter Software. The name entered is used to identify all computers connected to the projector via the Christie Presenter software via either wired or wireless connections.
Section 4: Operation 4.10.3 Use Christie Presenter 111 Press the autorun icon in the system tray to pause or play the USB display. 222 After starting the Christie Presenter application, the main window can been seen (shown below). Icon Description Connect and search network display Stop/start displaying desktop contents to connected network display Select display region Configure Christie Presenter Manage all connected network displays Disconnect all connections E Series User Manual 020-000515-01 Rev.
Section 4: Operation Connect and search network display 111 Click the button to enter into the connection menu section. 222 If the IP address of the projector is known, enter the IP address and click the "Connect" button. If the IP address is not known, click the "Search" button to search for the projector on the network and select the projector to which you want to connect. Select the option "Directly" in order to proceed to the log in interface.
Section 4: Operation Select display region Once the connection is set up, click the button to select the size of the projection region: FullScreen, FixedSize, or Alterable. yy FullScreen: The default capture mode turns to Full screen when the program is launched. At that time, if screen capture starts, the image of the whole screen is transferred to a remote network display. yy FixedSize: FixedSize mode allows the users to place a frame on the desktop.
Section 4: Operation Configure Christie Presenter Click the button to configure Christie Presenter for Basic Setting and Advanced Setting. yy Basic Setting: Select language, change the region size of fixed size capture mode, and select if notification message popup is allowed. yy Advanced Setting: Select the quality of JPEG image, YUV sample format and network port setting. (The "Fixed" port is Port 5900) 4-34 E Series User Manual 020-000515-01 Rev.
Section 4: Operation Manage all connected network displays Click the button to control all the users and all the projectors connector to the same projector. Icon Description Administrator log in. Normal user log in. Device is connected. Device is not connected. The icon shows the current status and display position of the local screen on the network display. Click on the icon to change the display position. A dialog box will appear. Click this unlock icon to change the password.
Section 4: Operation 4.11 Card Reader Operation There are four operation modes in the Card Reader application: ----- USB Flash Devices Detection Screen Thumbnail Display Mode Images Display Mode Images Slide Show Mode 4.11.1 USB Flash Device Detection Screen: I n this mode, the Card Reader application detects any USB flash devices hot-plug events and displays the flash device icon. When the flash device is removed from USB, the icon disappears.
Section 4: Operation he user interface is designed to operate the card reader application with T a few keys (Enter/Left/Right/Up/Down). The following buttons are supported in the user interface: yy Previous: Move the selected item left. (Go to previous page when this is the leftmost item) yy Next: Move the selected item right. (Go to next page when this is the rightmost item.) yy Display: Display the selected image or display the selected folder. yy Thumbnail: Enter the Thumbnail Display Mode.
Section 4: Operation yy yy yy yy yy yy yy Thumbnail: Enter the Thumbnail Display Mode. SlideShow: Enter the Slide Show Mode. Actual Size: Display in actual size of the image. Best Fit: Display the image in best fit to the screen. EXIFDisp OFF/On: Enable/Disable EXIF information display. +90deg: Rotate 90 degree. -90deg: Rotate -90 degree. 4.11.4 Image Slide Show Mode: he following operations are supported in the Slide Show Mode operation T UI. yy yy yy yy yy 4-38 Stop: Stop Slide Show Mode.
Section 4: Operation hen the image cannot be displayed due to memory limitation or cannot W support image format, the specific image is displayed on the center of the screen. E Series User Manual 020-000515-01 Rev.
Section 4: Operation 4.12 Install the Lamp The projector automatically detects the lamp life. When the lamp life is nearing the end of use, you will receive a warning message. When you see this message, please change the lamp as soon as possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp. 111 222 333 444 Note the number of the lamp that needs to be replaced on the “Current Lamp” menu.
Section 5: Troubleshooting 5. TROUBLESHOOTING If you are unable to resolve an issue using the information provided in this section, contact your reseller or service center. Problem Solution yy No image appears -- Make sure all the cables and power connections are correctly and securely connected See “Installation”. on-screen -- Check if the lamp is securely installed. -- Make sure you have removed the lens cap and the projector is switched ON.
Section 5: Troubleshooting Problem yy Partial, scrolling or incorrectly displayed image Solution -- If you are using a Notebook: 111 Adjust resolution of the computer. 222 Press the keys listed below for your notebook manufacturer to send signal out from notebook to projector.
Section 5: Troubleshooting Problem yy Image is out of focus Solution -- Make sure both lens caps (front and back) are removed. -- Adjust lens focus to fit. -- Make sure the projection screen is between the required distance. yy The image is stretched when displaying 16:9 DVD title -- When you play anamorphic DVD or 16:9 DVD, the projector will show the best image when the projector display mode is set to 16:9 in the OSD.
Section 6: Specifications 6. SPECIFICATIONS 6.
Signal Type Resolution Frame Rate (Hz) SECAM SECAM (M) 50 480p 60 ● ● ● ● ● ● 576p 50 ● ● ● ● ● ● 1080i 60 ● ● ● ● ● ● 720p 50 ● ● ● ● ● ● 720p 60 ● ● ● ● ● ● 1080p 24 ● ● ● ● ● ● 1080p 25 ● ● ● ● ● ● 1080p 30 ● ● ● ● ● ● 1080p 50 ● ● ● ● ● ● 1080p 60 ● ● ● ● ● ● HDMI 1 HDMI 2 VGA DisplayPort BNC Component S- video CVBS ● ● EDTV HDTV 6.
Section 6: Specifications 6.3 Key Features yy HD 0.65” 1920 × 1080 resolution or WUXGA 0.67” 1920 × 1200 resolution yy Projection lens compatibility: -- Horizontal offset ranges: +/-20% -- Vertical offset ranges: +120%/-40% (WUXGA) and +134%/-40% (HD) -- Exception: 0.8:1 lens must be used on axis. NOTE: Measurements are based on industry standards where offset is calculated as a ratio of the number of pixels shifted up/down to half the image size.
6.4 List of Components This projector comes with all the items shown below. Check to make sure your package is complete. Contact your dealer if anything is missing. yy IR remote control (133-114117-01) yy Power cord x 4 -- UK/Korea/Russia -- North America -- Europe -- Japan yy DVI to HDMI dongle yy User manual (CD) NOTE: Due to the difference in applications for each country, some regions may have different accessories. 6.
Section 6: Specifications 6.6 REGULATORY yy Safety -- CAN/CSA C22.2 No. 60950-1 -- UL 60950-1 -- IEC 60950-1 -- EN60950 yy Electro-Magnetic Compatibility Emissions -- FCC CFR47, Part 15, Subpart B/ICES-003/ANSI C63.
yy Marking -- This product shall conform to all relevant Canadian, US, and European directives, standards, safety, health and environmental concerns and bear the following markings at product launch: `` UL `` CE `` RoHS `` WEEE -- Future product markings to include International Certifications: CCC, KC, PSE, c-tick, Gost-R, South Africa -- International packaging recycling mark requirements: `` EU Directive (2002/96/EC) on waste and electrical and electronic equipment (WEEE); `` EU Directive (94/62/EC) o
Section 6: Specifications 6.7 Declaration of Conformity for EU Countries yy EMC Directive 2004/108/EC (including amendments) yy Low Voltage Directive 2006/95/EC yy Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC 6.8 Federal Communications Commission (FCC) Warning WARNING yy A shielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception.
6.
Section 6: Specifications Level 1 Level 2 Image Freeze Level 3(Or List) Off / On Gamma BrilliantColorTM White Peaking Image settings Advanced Image Settings Color Temperature Edge Enhancement Color Wheel Speed Color Enhancement Language Lens settings SPEC define Focus Zoom Lens Shift Lock all Lens Motors Ceiling Mount Rear Projection Lens center calibration Off/On/Auto Off/On Menu Horz Offset Menu Vert Offset Show Messages Menu Transparency Menu Preferences Splash Screen Setup PIN Protect Change
Level 1 Level 2 Image Blending Level 3(Or List) Drop Off Curve Image Gamma Level 4(Or List) 70-300 1.8/2.0/2.2/2.4/2.
Section 6: Specifications Level 1 Level 2 Lamp Auto Switch Lamp Auto Switch Time (Hours) Lamp Status Lamp Info Lamp Life Setting Reset Lamp Hours… Light Sensor (see Note 6).
United Kingdom ph: +44 118 977 8000 Eastern Europe ph: +36 (0) 1 47 48 100 Singapore ph: +65 6877-8737 Japan ph: 81-3-3599-7481 France ph: +33 (0) 1 41 21 00 36 Middle East ph: +971 (0) 4 299 7575 Beijing ph: +86 10 6561 0240 South Korea ph: +82 2 702 1601 Germany ph: +49 2161 664540 Spain ph: + 34 91 633 9990 Shanghai ph: +86 21 6278 7708 *36.8HP05G001-B* P/N 36.
