User manual

Appendix A: Menu Tree
A-4 Mirage J Series User Manual
020-100708-01 Rev.1 (11-2011)
Configuration
1. Language 2. Output Options 3. Lens Settings 4. Power Management 5. Date & Time 6. Menu Preferences 7. Communications 8. Geometry & Color 9. Diagnostics & Calibration 10. Service 11. Option Card Settings 12. Reserved
Menu Preferences
1. Large Menu Font 2. Menu Location 3. Horizontal Shift 4. Vertical Shift 5. Display Automatic Message Boxes 6. Display User Message Boxes 7. Reserved 8. Display Error Messages 9. Logo Screen Preferences 10. OSD Transparency 11. Menu Type 12. Splash Screen 13. Cascading Menus
Date & Time
1. Date 2. Time
Output Options
1. Screen Image Orientation 2. Reserved 3. Reserved 4. Frame Locking 5. Set Frame Delay 6. Actual Frame Delay 7. Free Run Frequency 8. Fade to Black Time 9. HDMI Output Loop Source
Power Management
1. LCD Backlight 2. LCD Backlight Timer 3. LCD Backlight Level 4. Auto Power Up 5. Auto Shutdown Enable 6. Turn Off Image After (min) 7. Enter Standby After (min) 8. Reserved 9. Over-Temp Fan Assist
Lens Settings
1. Intelligent Lens System 2. Manual Zoom/Focus 3. Calibrate 4. Lock all Lens Motors 5. Calibrate on New Lens 6. Calibrate on Startup 7. Home Position
Calibration Status
Communications
1. Serial (RS-232 IN) Options 2. Serial (RS-232 OUT) Options 3. Serial (RS-422) Options 4. Projector Address 5. Network Routing 6. Ethernet Settings 7. Broadcast Keys 8. Front IR Enabled 9. Rear IR Enabled 10. Wired Keypad Enabled 11. DMX / ArtNet Settings 12. SNMP
Ethernet Settings
1. IP Configuration 2. IP Address 3. Subnet Mask 4. Gateway 5. TCP Port 6. Host name 7. Domain name
MAC Address
Serial (RS-232 IN) Options
1. Baud Rate (RS-232 IN) 2. Serial Flow Control (RS-232 IN) 3. Serial Mode (RS-232 IN) 4. Serial Protocol (RS-232 IN)
Serial (RS-232 OUT) Options
1. Baud Rate (RS-232 OUT) 2. Serial Flow Control (RS-232 OUT) 3. Serial Mode (RS-232 OUT) 4. Serial Protocol (RS-232 OUT)
Serial (RS-422) Options
1. Baud Rate (RS-422) 2. Serial Flow Control (RS-422) 3. Serial Mode (RS-422) 4. Serial Protocol (RS-422)
Advanced Menu continued
Option Card Settings
1. Video Decoder Input card 2. Dual HD/SDI Input Card 3. Twin HDMI Input Card 4. Analog BNC Input Card
Video Decoder Input card
1. Grouped-Inputs Mode 2. Connector 1 Grounding 3. Connector 2 Grounding 4. Connector 3 Grounding 5. Connector 4 Grounding 6. Connector 5 Grounding 7. Connector 6 Grounding
Dual HD/SDI Input card
1. Dual Link Mode
Twin HDMI Input card
1. EDID Timings For Input 1 2. Tx Mode for Output 1 3. EDID Timings For Input 2 4. Tx Mode for Output 2
Menu will be filled with types
that match cards plugged in
Analog BNC Input card
1. Connector Grounding 2. Red Odd Pixel Offset 3. Green Odd Pixel Offset 4. Blue Odd Pixel Offset 5. Red Odd Pixel Gain 6. Green Odd Pixel Gain 7. Blue Odd Pixel Gain 8. Odd Pixel Phase Offset 9. Pixel Phase 10. Input Level Detector 11. Level Detector Threshold 12. Auto Color Enable 13. Color Enable
See Page A5 for: 8. Geometry & Color 9. Diagnostics & Calibration 10. Service
Dual Link DVI Input card
1. EDID Timings for Input 1 2. EDID Timings for Input 2
DMX / ArtNet Settings
1. DMX Interface 2. DMX Personality 3. Base Channel 4. Software Termination 5. Artnet Universe 6. Artnet Subnet 7. Input Noise Filter 8. Host name
Main Menu
1. Size & Position 2. Image Settings 3, Channel Setup 4. Configuration 5. Lamp 6. Status 7. Secondary Input & Switching 8. Language 9. Test Pattern
Press F
UNC
followed by two numeric numbers to enable
a specific color or colors in the display:
Func60=white Func61=red Func 6 2 = green Func63=blue Func64=yellow Func65=cyan Func66=magenta Func67=white Func 6 8 = Func69=invert(3Donly) Func09=Ifpressedfrom Status page, opens Service
Status page (For Service personnel only)
Func Help = disables Keystone, Edge Blending and
Brightness Uniformity without changing the settings associated with them.
Logo Screen Preferences
1. Splash Screen Setup 2. Splash Screen 3. Show Logo Image 4. Horizontal Position 5. Vertical Position
SNMP
1. SNMP Read Community 2. SNMP Location 3. Trap IP Address 1 4. Trap IP Address 2 5. Trap IP Address 3 6. Email Recipient 1 7. Email Recipient 2 8. Email Recipient 3 9. Email From: Address 10. SMTP Server IP Address 11. Trap Configuration
Trap Configuration
1. Lamp Life 2. Lamp Fault 3. Fan Stall 4. Thermal Sensors 5. Power 6. Video signal lost/detected 7. Lamp Door