CCM-LX USER MANUAL 020-000326-01 Downloaded From projector-manual.
Downloaded From projector-manual.
020-000326-01 K ACT LIN CCM-LX Network Capture 3 Network Viewer 3 Network Communication User Manual Downloaded From projector-manual.
Compliance Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Compliance and Caution CAUTION ON USE IN NETWORK - When you receive an alert e-mail from the projector, you must check the projector immediately. Fire or accident may result if the projector is used in an abnormal condition. - When you install the projector at remote location and use it through the network, you must perform the safety inspections periodically. In this case you must pay attention to the change of environment in which you installed the projector.
Contents Compliance ..........................................................................................................................................................................2 Federal Communications Commission Notice ....................................................................................2 Chapter 1 Preparation ................................................................................................7 Features................................................................
Contents Start/stop the multi control...........................................................................................................................64 Register the projector .......................................................................................................................................65 Confirmation of registered projector ......................................................................................................65 Change the mode of the registered projector .
6 Downloaded From projector-manual.com Christie Manuals CCM-LX User Manual 020-000326-01 Rev.
Chapter 1 Preparation 1 ENGLISH Describes features and operating environment of this product. CCM-LX User Manual 020-000326-01 Rev.1 (10-2010) Downloaded From projector-manual.
Chapter 1 Preparation Features Real Time Capture function ( p.72) To display the screen image of the computer by the projector through the network in real time. PC1 PC2 Capture PC3 PC4 PC6 PC5 Network Communication function ( p.77) To communicate by sharing the captured image of a computer with multiple computers and a projector. User can draw the text and figure on the captured image by using a drawing tool.
Features Web Management function ( p.46) With this func tion, you can monitor projector functions such as power status, lamp s t at us, inp u t m o d e, signal condition, lamp-use time, etc. through the network by using the web browser installed on your computer. PC1 PC2 PC3 PC4 PJ2 PJ1 PC6 PC5 Turn ON PJ2 E-Mail Alert function ( p.38) The projector (Network Unit) sends messages to the registered e-mail addresses when a lamp abnormality or power failure occurs with the projector.
Chapter 1 Preparation Multi-control function ( p.63) A single computer can control and set up the multiple projectors at the same time. PJ1 PJ2 PJ3 PJ4 PC6 PC5 PC4 Select Input2 for PJ1 to PJ4. Automatic On/Off using Clock function ( p.58) Automatically turn on or off the projectors at specified date/ day and time by using the clock function.
Operating Environment Operating environment of CCM-LX To perform the managing and setting of the projector by using this product, the environment described below is required.
Chapter 1 Preparation The limitation*1 of connection between this product and hub or computer Use an appropriate cable when connecting the projector and a hub or computer. And, please use a shielded LAN cable. Connection Type of usable LAN cable Maximum length Network Unit - Hub STP Straight Cable with category 5 * 100m Network Unit - Computer STP Cross Cable with category 5* 100m 2 2 *1 There may be other limitations depending on your network environment or LAN specification.
Before use Notice Expression/Abbreviation The word "projector" found in this manual means "projector provided with Network unit" unless otherwise noted. The OS of the computer and the Web browser described in this manual is Windows XP Professional and Internet Explorer 6.0. In case of another OS or Web browser, some instruction procedures may differ from the actual operation depending on your computer environment.
Chapter 1 Preparation 14 Downloaded From projector-manual.com Christie Manuals CCM-LX User Manual 020-000326-01 Rev.
Chapter 2 Installation 2 ENGLISH Describes how to install the network unit and software, and configure the network. CCM-LX User Manual 020-000326-01 Rev.1 (10-2010) Downloaded From projector-manual.
Chapter 2 Installation Flow of installation The following are instructions for attaching this product to the projector and connecting it to the network. Please review the entire procedure to become familiar with it. 1 Function of the network unit ( p.17) Explains the name and functions of each part of the network unit. 2 Installation and network configuration ( p.18-24) 1. Mount this product onto the projector. 2. Connect the LAN cable and join it to the network. 3.
Name and function of each part [1] Name and function of each part (Top View) POWER indicator This lights up red when the network function is set ON in the projector menu. Mounting screws Mount by using a coin etc. ( K p.18) ACT LIN ACT indicator This turns on and off with green when sending or receiving of data LINK indicator This lights up red when the network unit is connected to the network correctly. (Bottom View) Connector plug LAN port Connecting the LAN cable.
Chapter 2 Installation [2] Installation and network configuration Mounting 1. Disconnect the AC plug from the projector. 2. Remove the connector cover from the projector. Keep the connector cover and the screws importantly. Screw 3. Attach this product to the option connector and tighten two screws by using a coin etc. ! 18 Connector cover Caution AC cord must be disconnected when mounting or removing this product otherwise it may damage the product.
Installation and network configuration Connection of LAN cable To connect to the network, it is required to use the STP (Shielded Twisted Pair) straight cable with RJ-45 plug. Prepare the Hub (10Base-T or 100Base-TX) to distribute the network cable if required. 1. Disconnect the AC plug from the projector. 2. Connect the STP straight cable to the LAN port on the network unit. UTP straight cable 3. Connect the STP straight cable to the hub.
Chapter 2 Installation Network configuration Confirmation of the network menu When installing this product to the projector, the built-in network function is not available, and this product are activated automatically. If not activated, the product may not have been installed correctly. Please check item "Mounting". ( p.18) Configure the network Before performing the network configuration, prepare network address numbers (IP Address, Subnet Mask, Default Gateway, DNS) assigned to the projector.
Installation and network configuration 2. Configuration for IP Address/ Sub net/ Gateway*1/DNS*2 Select "Network Setting" in the Network menu, and press SELECT button. The following network setting pallet appears on the screen. Enter the specified network addresses. In addition, "DHCP" is not available. ( p.24) Select an item with a orange cursor by using the point buttons ! or ,and Press SELECT button. Move the white cursor sequentially left or right with point buttons .
Chapter 2 Installation Network PIN code setting The Network PIN code can be set to restrict access to the setting page of the projector using the web browser. Default Network PIN code [0000] means no Network PIN code is set. 1. Displaying Network PIN code menu Select network menu and then select "Network PIN code" sub menu. Press point button or SELECT button to display the Network PIN code entry pallet. 2. Entering the Network PIN code To enter the Network PIN code, use point buttons ! remote control.
Installation and network configuration How to enter the numbers with the remote control 10-key buttons During the network address input mode or the network PIN code input mode, some of the buttons on the remote control are operate as the 10-key input buttons. 1. Select an item with the orange cursor by using the point buttons ! or , and press SELECT button. 2. Select a column with the white cursor by using the point buttons or . 3. Press 0 to 9 key assigned to the buttons to enter the numbers.
Chapter 2 Installation Notice about system construction For installation of multiple projectors into the same network with network unit. Do not install multiple projectors with network units that have their default network settings to the same network. The use of the network units which have the default IP address set to the same network settings will cause IP addresses to collide and create a malfunction.
Installation and network configuration [3] Installing the software It is required to install the software into your computer to use the Network Capture function and Network Viewer function. Please install the software as follows. Note: To install the software into the computer, you should logon as administrator. Before installation, make sure that the other applications are closed, otherwise proper installation cannot be made. Network Viewer & Capture 3 installation 1.
Chapter 2 Installation Installed software The following 3 software are installed on your computer. L Network Capture 3: Capture the displayed image of the computer and serve it to the projector via the network. This software is registered into "startup folder" of the computer and the capture icon stays on the task bar after booting the computer. L Network Viewer 3 (File Converter 1): Converts to the JPEG*1 data format which can be projected with the projector from the JPEG, bitmap and Power Point files.
Installing the software File Converter 2 Installation 1. Set the supplied Network Viewer & Capture 3 CD-ROM into the CD-ROM drive of your computer. Double click SetupDrv.exe icon in the "Driver" folder in the CD-ROM. 2. Select "English [United States]" from the pull-down menu on the language selection window and then click Install button to start installing. Installed software and places Network Viewer 3 (File Converter 2) is installed in the "Printers and Faxes" folder in the "Control Panel".
Chapter 2 Installation 28 Downloaded From projector-manual.com Christie Manuals CCM-LX User Manual 020-000326-01 Rev.
Chapter 3 Basic Setting and Operation 3 ENGLISH Describes basic operations and settings for controlling the projector by using the web browser. It is required that computer and projector is connected to the network and the network address is properly configured. CCM-LX User Manual 020-000326-01 Rev.1 (10-2010) Downloaded From projector-manual.
Chapter 3 Basic Setting and Operation Login the setting page of the projector 1. Enter the IP address Launch the web browser installed in your computer, enter the IP address into the "Address" on the browser and then press "Enter" key. Enter the address set in "Network configuration" ( p.20). (The default IP address of this product is [192.168.0.2].) The numerical value is a setting example. 2.
Login the setting page of the projector 3. Display of main setting page The following main setting page will be displayed according to your display mode selection. Perform various kinds of settings through this page. Click on the menus to display the control and setting pages. M Main setting page in the Standard Mode display Clock display Display on or off by clicking text ON or OFF Sub menu tab Switches the sub menu tab. Page numbers Switches the pages by clicking the number's tab.
Chapter 3 Basic Setting and Operation K Main setting page in the Light Mode display Sub menu tab Page numbers Returns to the display mode selection page. Main menu Setting page Returns to main menu The blank page appears if your PDA does not provide a Adobe Flash Player. You need to install the Adobe Flash Player. ( p.31) The network viewer function in the Light mode has following limitation; - Cannot select the program or folder for the display. ( p.97, p.
How to use the setting page Type of the setting pallet Text box setting Enter a number or text and then click Set button. or Change a value with S or T button and then click Set button. The value changes quickly when keeping pressing S or T button. Pull-down menu setting Select an item with pull-down menu button and then click Set button. or Select an item by clicking S or T button.
Chapter 3 Basic Setting and Operation Initial setting After installing this product to the projector, perform the following basic initial setting. Click Initial Setting on the main menu to display the initial setting page. The model name of the projector on which this product is mounted is displayed on the page. Item Description Language.............. Switches display language on the setting page. English or Japanese. Model name .......
Initial setting Network PIN cord setting This is to set the Network PIN code to restrict the access from an unauthorized person through the network. Enter a 4-digit number as the Network PIN code onto the text box and click Set button. The network unit begins restarting and it takes about 20 seconds. Close (Quit) the web browser and access to the login page again in 20 seconds. This is to perform the login authentication firmly. The default Network PIN code [0000] means no Network PIN code is set.
Chapter 3 Basic Setting and Operation Item Description Time setting ........ When clicking AUTO button, the date and time set on your computer are set to the network unit. Current time ....... Indicates current date and time set on the network unit. Date ..........................Sets date in manual. Time ..........................Sets time in manual Date and time setting Auto setting Click AUTO button on the page, the date and time set on your computer are set to the network unit.
Network configuration Network configuration Click Network on the main menu. The following setting page is displayed. The IP Address, Subnet Mask, Default Gateway, DNS (Domain Name Server) and projector name are set up on this Setting sub menu. The IP address and Subnet Mask have been configured already in chapter "Installation". If you want to change them or configure default gateway or DNS, perform them in this page. If you change them, the network unit begins restarting and it takes about 20 seconds.
Chapter 3 Basic Setting and Operation E-mail setting This product has an E-mail function which can send an alert message to users or an administrator if it detects an abnormality on the projector or run out of the life span of the lamp. Click E-mail Setting on the main menu and follow the below steps. 1. Setting SMTP server and administrator address Enter the server name or IP address of the SMTP server*, the port number of the SMTP server and administrator address and click Set button.
E-mail setting 2. Setting SMTP authentication Set the SMTP authentication concerned and click Set button. Please contact your network administrator in details. Item Description SMTP Authentication setting Auth ...................... Sets authentication setting option. (OFF, SMTP Auth, POP before SMTP). SMTP Auth........ Sets user authentication setting option when selecting "SMTP Auth" in above column. (CRAMMD5, LOGIN, PLAIN) User ID ....................Sets SMTP user ID. (up to 63 characters) Password .
Chapter 3 Basic Setting and Operation 5. Option selection for sending alert mail Click Option sub menu tab. Check the condition items under which alert mail will be sent and click Set button. Please refer to item "Examples :Type and contents of alert mail" described on the next page. [1]–––––––––––––––––––––––––––––––––– O When PJ lamp is off. O When PJ lamp replacement time is reached. O When PJ needs service. O When internal PJ temperature is too high.
E-mail setting L When PJ lamp replacement time is reached: TITLE: Message from projector 10-03-2005 00:59 Projector Model Name: model name TCP/IP: 192.168.1.201 Projector Name: Proj05 It sends you following message. *The projector lamp has reached replacement time. Lamp 800 h Replace it with a new lamp immediately. If the projector is used without replacing it with a new lamp, the alert mail is sent to users in every power-on of the projector.
Chapter 3 Basic Setting and Operation SNMP setting This product provides a SNMP (Simple Network Management Protocol) agent function. The SNMP consists of a manager and agents. The group which communicates information each other with SNMP is called "Community". There are two access modes in a community, Refer (read) and Set (read- write). This product allows to use Refer only (read only). The SNMP message informs the projector status called "Trap" to an administrator.
SNMP setting Trap Item Description Community name ...... Enter community name to send "Trap". Default name is "public". Trap address ....... Enter IP address of the SNMP manager computer to receive "Trap". Trap check/delete Check and delete the trap address Checking the registered trap address and deleting the address. To delete the address, tick check box in front of the IP address and click Delete button. ENGLISH Up to 10 trap addresses can be registered. CCM-LX User Manual 020-000326-01 Rev.
Chapter 3 Basic Setting and Operation Trap option Trap option setting Tick check boxes in front of the condition item to send the trap. Click Set button if you tick or un-tick the check box on a page. [1]–––––––––––––––––––––––––––––––––– O When PJ lamp is off. O When PJ lamp replacement time is reached. O When PJ needs service. O When internal PJ temperature is too high. O When PJ is turned into Standby in proper user operation.
Chapter 4 Controlling the Projector 4 ENGLISH Describes controlling and setting of the projector by using the web browser. CCM-LX User Manual 020-000326-01 Rev.1 (10-2010) Downloaded From projector-manual.
Chapter 4 Controlling the Projector Power control and status check Click Power & Status on the main menu. The control page will be displayed. By clicking ON or Standby button on the page, the power of the projector can be controlled. Confirmation window as shown in the below appears when the Standby button is pressed. Popup confirmation window Item Description PJ status Power ......................... Displays the status of the lamp. (ON, OFF, On starting up, On cooling down, Service in need) Status ....
Power control and status check About projector condition Status Description Normal ............................................................... Projector is operating normally. Power management in operation ........... Power management is operating Shutter management in operation .................... Shutter management is operating Lamp failure ................................................... Lamp failure is occurring Abnormal temperature .........................
Chapter 4 Controlling the Projector Controls Click Control on the main menu. The setting method differs depending on the contents of the page. Click on the page number to change pages and select desired setting items. Please see the owner's manual of the projector to have the further information of each control item. Input This function is to select the input mode and source mode of the projector. Click Set button after selecting the input and source mode. Item Description Input.......................
Controls System This function is to select the system of signal input to the projector. The available system mode are listed on the pull-down menu button according to the input signal. Select a system and then click Set button. Available selection at the RGB(PC analog) input Item Description XGA1 ........................ It automatically switches to the proper computer system of the input signal. * The computer system modes (VGA, SVGA, XGA. SXGA, UXGA, WXGA...) which meet the input signal are listed.
Chapter 4 Controlling the Projector Image adjustment This function is to adjust the projected picture image and save the image mode. To store the adjusted value, click Store button, and to load the adjusted value, click Load button. Item Description Contrast .................Adjusts picture contrast (0~ 63) Brightness ............Adjusts picture brightness (0~ 63) Color .........................Adjusts picture color saturation (0~ 63) Tint ............................
Controls Sound This function is to adjust the sound of the projector. The values in the text box represent the current control value or status. Item Description Volume ................... Adjusts the sound volume from the speakers.(0 ~ 63) Mute ......................... Suppresses the sound. (ON, OFF) Built-in SP. ............. The use of the built-in speaker is enabled. (ON, OFF) Menu This function is to control the On-screen menu of the projector.
Chapter 4 Controlling the Projector PC adjustment Click PC Adj. on the main menu. This function is to adjust the signal from the computer connected to the projector to obtain the proper picture image on the screen. Item Description Current mode ......Displays a current mode like VGA, SVGA, XGA. SXGA, UXGA, WXGA, etc. or MODE1 - MODE10, EXT11 EXT50 which are the customized mode created by using the "Mode Store" function described below.
Setting up the projector Setting up the projector Click Setting on the main menu. This function is to set up the projector. Select the sub menu [Screen setting] or [Setting] and then set up each setting.
Chapter 4 Controlling the Projector Item Description Input button ...... Sets the function of the Input button. (Mode1, Mode2, Mode3) Logo ......................... Sets on or off the logo display on the screen during the startup. (User, Default, OFF) Background......... Sets screen background to blue when no signal input. (Blue, User, Black) Display .................... Switches on or off the on-screen menu display on the screen. (ON, Countdown off, OFF ) Picture in Picture.....
Setting up the projector Item Description Filter warning..... Sets the time to indicate the filter replacement message on the screen. (OFF, 400H, 700H, 1000H) Filter counter ....... Click Reset button to reset the filter use time of the projector when you replace the filter cartridge with new one or roll-up the filter. Filter control .......... Indicates the number of remaining times for the filter scroll. To roll-up the filter, click Roll-up button and then SELECT button.
Chapter 4 Controlling the Projector Save the controls and settings This page is to save and load the controls and settings of the projector in the block. The storable items are "PC adjustment", "Control" and "Setting". Store/free the settings 1. Click Save menu on the main menu. 2. Select a set number (Totalsave1 to Totalsave10) you intend to store current settings with the pull-down menu button of the item Store & Free. Name this set number onto the Memo text area.
Save the controls and settings Check the saved items Click Check button to check the current setting condition of the controls. Each item of "PC adj.", "Control" and "Setting" is displayed sequentially. Click Stop button to cancel the auto page display. Load a control set Select a set number ENGLISH Selec t your desired set number (Totalsave1 to Totalsave10) with the pulldown menu button of Load Set and then click Load button.
Chapter 4 Controlling the Projector Timer setting This page is to set the timer to turn the projector off or on at a programmed day/date and time. Follow the steps below for setting. Click Timer on the main menu. Present time set on the network unit Select date Select day Set execute time Event action How to set the timer 1. Set a day or date To set the timer event at same time everyday or every week, Select day entry with radio button and then select desired day with the pull-down menu button.
Timer setting 2. Set an execute time Type the time with (Hour:Minute) and 24 hours format. Ex.: Type [18:25] if you specify [PM 6 o’clock and 25 minutes]. 3. Select an event action Select an event action from the pull-down menu. Event Action ON..................................Turns on the projector OFF ................................Turns off the projector Lamp Auto ...............Changes lamp mode to "Auto" Lamp Normal .........Changes lamp mode to "Normal" Lamp Eco1 ...............
Chapter 4 Controlling the Projector Notes on timer setting Up to 10 timer events can be registered. Timer events always operate according to the next valid event depending on the projector's power status. In the example below, event 3 turns on the projector so next event 4 (also turning on projector) will not be effective because the projector is already turned on. Similarly, when the projector is turned off by event 5, event 6 OFF will not be effective in turning it off again.
Projector information Projector information This page is to display the basic information of the projector status. Click Information on the main menu. Click this button to update the information Items Description Input* ......................Displays selected input and source. System ....................Displays selected signal system. Signal.......................Input signal status (Yes, No) Screen .....................Displays screen mode. Lamp status ..........
Chapter 4 Controlling the Projector Items Description Network MAC address* .... Displays MAC address of the Network Unit. IP address ............. Displays IP address of the Network Unit. * MAC address is shown on the back of the network unit. If you need to know the MAC address before installing the unit. Turn it down and check the MAC address.
Multi-control Multi-control Controlling and setting the multi-projectors This function enables you to control the multiple projectors equipped with the network units that are connected to the network. Click Multi Control on the main menu to display the control page. Note: To control the multiple projectors, each projector must have the same Network PIN code. Example of multi control PJ1 PJ2 PJ3 PJ4 PC5 PC4 Select Input2 for PJ1 to PJ4. CCM-LX User Manual 020-000326-01 Rev.
Chapter 4 Controlling the Projector Start/stop the multi control To start or stop controlling the multi-projectors, click Multi control setting menu and select ON or OFF. Switches on and off the multi-control function Multi control setting OFF ........Stops multi control function ON .......... Starts multi control function. The multi control menu will appear when setting ON. These items of menu are linked to the main menu.
Multi-control Register the projector To use the multi control function, register the IP address of the projector you intend to control. Click PJ registration sub menu tab and set the IP address, Memo and Multi control item, then click Set button. Items Description IP address .............Enter IP address of the projector to control. Memo ......................Enter projector name or installed location etc. Multi control item Control .............. Controlling the projector Control&Image......
Chapter 4 Controlling the Projector Change the mode of the registered projector To change the mode of the registered projector, select a mode with the pull-down menu button under the IP address of the target projector and then click Set button. Mode Operation Control .................... Controlling the projector Control&Image ........... Controlling and displaying images Image ...................... Displaying the images OFF ............................ Excluding from the multi-control Delete ..........
Multi-control Check & Change page in the light mode Following functions in the "Check & Change" page are not available in the light mode. - Changing the control mode. - Deleting the registered IP address - Indicating the each status - Indicating the each memo This indicates that the mode is "Image". This indicates that the mode is "Control".
Chapter 4 Controlling the Projector Viewer auto setting all together "Viewer auto display" can be set all together. Set "ON" the multi control setting and select [3] Auto display from Viewer sub menu (selected by ‘Multi-control’ - “Network Viewer” menu). Set the display time periods and repeat times for the auto image display. When clicking Start button, the registered projectors start playing back the auto image display in sequential.
Chapter 5 Network Capture 5 ENGLISH Network Capture is a function to display the screen image of the computer via the network. - Real Time Capture - Network Communication CCM-LX User Manual 020-000326-01 Rev.1 (10-2010) Downloaded From projector-manual.
Chapter 5 Network Capture About Network Capture function The Network Capture is a function to project the screen images of the computer which has a Network Capture 3 software by the projector through the network. This function has 2 kinds of mode as the below. - Real Time Capture ( p.72) A function to display the screen image of the computer by the projector through the network in real time. - Network Communication ( p.
About Network Capture function Items Description Start real time capture ..................Starts the real time capturing. ( p.72) The screen image of the computer is projected on the screen in real time. Start communication ....................Starts the Network Communication. ( p.77) Captured image is projected on the screen. The captured image edit window appears on the computer screen. Parameter set up............................
Chapter 5 Network Capture Using the Real Time Capture This is a function to project the screen image of the computer by the projector in real time. The captured image projected by the projector can be selected from the computer, web browser and the projector respectively. Registering the computers Up to 30 computers can be registered. 1. Access to the control page of the projector by using the web browser. From the Network menu, click Capture tab to display the setting page. ( p.37) 2.
Using the Real Time Capture [1] Control by the computer * PC provides the Network Capture. PC1 PJ2 Project this screen PC2 PC2 image with PJ2. PJ1 Capture PC3 PC4 PC6 PC5 Select input mode of the projector to "Network" previously. 1. Click Network Capture 3 icon on the task bar. 2. Click Start real time capture on the popup menu. The screen image of the computer will appear on the projected screen in real time. r 5P TUPQ DBQUVSJOH DMJDL Stop real time capture on the popup menu.
Chapter 5 Network Capture [2] Control by the web browser * PC provides the Network Capture. PC1 PJ2 PC2 PJ1 Capture PC3 PC4 PC6 PC5 Project a screen image of PC1 with PC2. * Start capturing of the PC1 from the PC5. Select input mode of the projector to "Network" previously. 1. Access to the control page of the projector by using the web browser. From the Network menu, click Capture tab to display the setting page. ( p.37) 2.
Using the Real Time Capture [3] Control by the projector * PC provides the Network Capture. PC1 PC2 Project a screen image of PC1 with PC2. PJ2 PJ1 Capture PC3 PC4 PC6 * Start capturing of the PC1 from the projector PJ2. PC5 Select input mode of the projector to "Network" previously. 1. Select "Network Capture" in the Network menu and then press point button or SELECT button. 2.
Chapter 5 Network Capture Advanced using example Displays the presentation data stored in the computer by using the wireless mouse function from the projector. 1. Start capturing of the computer PC1 by using the projector. Select “Network Capture” icon from the menu and select "PC1" and then select "Connect". ( p.75) => The Network Capture software installed in the selected computer will start capturing. 2.
Using the Network Communication Using the Network Communication This Network Communication is to communicate by sharing the captured image of a computer with multiple computers and a projector. User can draw the text and figure on the captured image by using a drawing tool. The data that has the captured image of a Main PC and communication information is sent to the projector. The projector projects this data onto the screen and serves this data to other computers (Sub PC) at the same time.
Chapter 5 Network Capture Settings before using the Network Communication To use the Network Communication, the capture setting of the network should be set either [1] or [2] described below. [1] Setting the network unit searches all the available target computers in the network automatically. or [2] Setting the target computers are registered to the network unit. Perform capture setting following to the description below. [1] When serving the capture data to all the target computers in the network.
Using the Network Communication Description of capture editing window Select menu "Start Communication" from the popup menu appearing by clicking the Network Capture 3 icon on the task bar. The capture editing window will appear on the computer screen as the below. For basic operation of each menu, refer to the item "Menu tree" below. Menu Tool bar Capture Image Authority status indication frame ( p.
Chapter 5 Network Capture Tool bar button names The following commands are assigned to the tool bar buttons. For each operation, refer to the description of item "Menu tree".
How to use the Network Communication How to use the Network Communication Start the communication 1. Display an image on the computer screen. 2. Select Start Communication from the popup menu appeared by clicking Network Capture 3 icon on the task bar. The capture editing window with a captured image appears on the computer screen. Icon on the task bar If an error message appears, check item "Parameter set up". ( p.
Chapter 5 Network Capture Edit capture image Drawing figures 1. Click " :Pencil" button on the form tool bar. 2. Select its attribute (shape, width, color and translucence) from the form and attribute tool bar. 3. Drag a mouse pointer on the screen image to draw the figure. Erase drawn object 1. Click " :Eraser" button on the form tool bar. 2. Select its attribute (shape, width) from the form and attribute tool bar. 3. Drag a mouse pointer on the screen image to erase the figure.
How to use the Network Communication Drawing letter 1. Click " :Letter frame" button on the form tool bar. 2. Select a color of text with color tool bar. 3. Drag a mouse pointer on the screen image to specify the area of the letter frame. The letter input dialog window will appear. 4. Enter the letter onto the window. To change the letter attribute, click Letter attribute button. See item "letter attribute setting" below. 5. Click OK button to fix the content.
Chapter 5 Network Capture Network Communication operation and change of state Network Communication can be used under the environment which one or more computers are connected to the projector via the network. Preparation Launch the Network Capture 3 software on the target computer. ( p.70) Set the projector in the standby or turning on. Check IP address of the target computer is registered in the connection list. ( p.
Executing the forcing mode Executing the forcing mode The network capture setting of the web page provides a forcing executing command. This command executes the release of authority or ending the communication forcibly. This is useful when the other target PC keeps an authority all the time, or when the condition of the communication is not stable. Click page 2 Communication setting from the menu "Network"-"Capture". Execute command by clicking the button Free, Quit or Update.
Chapter 5 Network Capture Error information Error messages Cause and corresponding Set up the parameter. Error when executing the communication. The parameter setting (host name, capture port) has not been set. Check parameter setting. ( p.71) It has not been registered to PJ as a group. Error when executing Start Communication or Start real time capture. The IP address of the computer has not been registered. Register the IP address by using the web browser. ( p.
Chapter 6 Network Viewer 6 ENGLISH Network Viewer is a function to display the image data stored in the file servers by the projector through the network. Describes about file converter software File Converter 1, File Converter 2 and program creator software Program Editor, and how to use Network Viewer. CCM-LX User Manual 020-000326-01 Rev.1 (10-2010) Downloaded From projector-manual.
Chapter 6 Network Viewer Creating the available data [Network Viewer 3] The image available with this projector is the JPEG format (.jpg). There are several types of JPEG data. Before using the images with the Network Viewer function, it should be converted to the optimized JPEG data for this projector. [1] How to use the Network Viewer 3 (File Converter 1) The File Converter 1 is a software to convert from the JPEG, bitmap or Power Point data to the optimized JPEG data for the projector.
Creating the available data [Network Viewer 3] Menu Tree Menu Sub Menu Description View Update Preview size Option Convert a folder Convert each file Version information Updates contents of the preview window Sets size of the preview image, Large, Middle, Small Sets default of the output destination and conversion mode Converts files in a folder into JPEG files at once.
Chapter 6 Network Viewer 2. When converting each file, select a preview image first and then click Convert each file. To select two or more files at once, press and hold "Shift" key or "Ctrl" key and then click the preview images. When converting all the files in a folder, select a folder and click Convert a folder. 3. As the confirmation window appears, check the conversion object and conversion type and then click OK button.
Creating the available data [Network Viewer 3] Setting of output destination and conversion mode When clicking Change button on the confirmation window in the step 3 on the previous page, following option setting window appears. Output destination Select either Folder or FTP server as the output destination of the converted files. Folder Output folder ..... Specify a folder in the local hard disk or shared computer in the network. FTP server Host name............
Chapter 6 Network Viewer [2] How to use the Network Viewer 3 (File Converter 2) The File Converter 2 is a kind of the printer driver software to convert to the optimized JPEG data for the projection from the any documents created by the other software such as text editor, spreadsheet or presentation software. It is possible to convert to the JPEG file from the any kinds of documents created by the software which has a "print" menu. Create the available data 1.
Creating a program file [Program Editor] Creating a program file [Program Editor] Network Viewer 3 (Program Editor) is a tool to make a program file which specifies the display order of the image and its file path in the file server (FTP server). The Program Editor makes a folder "DispParam" at the login root directory in the FTP server and makes files as each program name into this folder. These files are called "Program".
Chapter 6 Network Viewer 4. Click New button. 5. Enter a program name and click Add button. 6. The folder selection window appears and select a Change : Changes the contents of the program file. Remove : Removes the program from the list. folder in which the JPEG data are stored and then click Add button to register into the folder lists. Add ....................Displays the folder selection window. Delete ..............Deletes the folder path from the folder list. UP .......................
Creating a program file [Program Editor] Setting up the display order and time of the images In the default setting, the display order of the images is ASCII code order of the file name. To change the display order or to set up the display time, take the following procedure. Display the folder list window in step 6 of the previous page. 1. Select a folder list contains images to change. 2. Click Edit button. The images in the selected folder are displayed with the file name on the index window.
Chapter 6 Network Viewer 3. To change the display order, select* files and then click UP or DOWN button on the menu bar to move them onto your desired place, or select files and then drag and drop them onto your desired place with mouse. 4. To change the display time*2, select*1 files and then click Display time button on the menu bar to display the Display time setting window. Check "Display time" check box and set display time. To cancel the display time, un-check the "Display time" check box.
Creating a program file [Program Editor] Example of the created program selection Use the web browser to access to the control page of the projector. Click Viewer of the Network menu on the web page, then connect to the FTP server and select the program name which was made at previous section. The projector starts displaying the images along the program. For further information, please see "Using the Network Viewer function". ( p.98) This function is not available in the light mode.
Chapter 6 Network Viewer Using the Network Viewer function The Network Viewer is a function to acquire the JPEG image data from the file servers placed in the network and project them on the screen. The projected image data are specified with the folder unit. You can set the display period and repeating times, and also you can register those folders as the program. *The network viewer function cannot be used when using the network capture function.
Using the network viewer function 2. Setup the setting page [1] of Image display setting. Item Description Host name............ Enter the host name or IP address of FTP server, your ftp server etc. Folder path .......... Use "/"(root directory) in normal, or enter the directory name follow the "/" as shown in the below example if you have a specified directory in the server. /data/ User ID* .................. Enter your login account of the FTP server Password*.............
Chapter 6 Network Viewer When clicking Set, the file list or preview list of the selected folder or program is displayed on the window. Decides a image to start auto display with radio button Selects a page The original image is displayed on another window by clicking on the preview image or file name Button Operation <<............................... Steps down the startup image in the auto display function >>...............................
Using the network viewer function 4. Auto Display setting and control page [3] Repeat times (0 to 255 times) * 0 means endless play Display period*1 of the image (3 to 240 sec.) Click here to check the further information of the file error The preview image will not Error info. appear when the option is set "Display OFF".( p.99) 1. Click Start button to start the auto-display. The image in the selected folder or program is displayed on the projector's screen.
Chapter 6 Network Viewer Error information Error type Description File Error It is displayed when the network unit cannot acquire the correct file images from the FTP server, or when the master projector is turned off during the multi-control. Click Error button to check the details. Connection Error It may be displayed when the slave projector is using the Network Viewer or Capture function during the multi-control. Check which projector has an error , see item "Multi Control/Check & Change". ( p.
Using the network viewer function Item Description Display mode ..... Selecting Auto display mode or Manual display mode. Auto.....................Displays image automatically by setting "Display length" and "Repeat times" Manual...............Controls image display (browsing image backward or forward) manually. Display Length .. Display period of the image.f (3 to 240 sec.) Endless play ........ Set "On" if the endless playback mode. Repeat times ......
Chapter 6 Network Viewer 104 Downloaded From projector-manual.com Christie Manuals CCM-LX User Manual 020-000326-01 Rev.
Chapter 7 Appendix 7 Connection examples Web browser setting Technical data ENGLISH Q&A CCM-LX User Manual 020-000326-01 Rev.1 (10-2010) Downloaded From projector-manual.
Chapter 7 Appendix Examples of connection Peer-To-Peer connection Connecting the projector (PJ01) to the control computer (PC05) directly. * STP cross cable Computer Name: PC05 IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Default Gateway : DNS : Projector Name: PJ01 IP Address : 192.168.0.2 Subnet Mask : 255.255.255.0 Default Gateway : 0.0.0.0 DNS : 0.0.0.0 Connecting the projector (PJ01) to the control computer (PC05) via the hub. Hub To another network Computer Name: PC05 IP Address : 192.
Examples of connection The gateway (Router) installed in the network Connecting the projector (PJ01) to the control computer (PC05) via the gateway. Entrance hall Computer Name IP Address Subnet Mask Default Gateway DNS : PC205 : 192.168.200.5 : 255.255.255.0 : 192.168.200.1 : 192.168.201.1 Projector Name: PJ01 IP Address Subnet Mask Default Gateway DNS : 192.168.200.15 : 255.255.255.0 : 192.168.200.1 : 192.168.201.1 Hub Network Group: 192.168.200.
Chapter 7 Appendix Use of telnet You can control the projector by using the telnet application* installed on your computer. Normally, the telnet application is available on your computer. * The telnet 10000 port is used to control the projector. Control (For example, in case of using the Telnet application of the Windows XP Professional.) 1. Select Run... submenu from Start menu on the computer. Type "telnet" onto the Open text area on the displayed window and press OK button. 2.
Use of telnet 4. Type the commands, refer to below table, to control the projector and then press "Enter" key for termination. For example, type "C00" which is a command to turn on the projector, and press "Enter" key. Confirm the projector is turning on. * Enter with ASCII 64-byte capital characters and one-byte characters. To disconnect the communication, press "Ctrl" key and "]" key at the same time, type "close" and then press "Enter" key on the Keyboard.
Chapter 7 Appendix Web browser setting This product is designed to enable the projector to be set up and controlled from an Internet web browser. Depending on the preference settings of the web browser, some control functions may not be available. Please make sure that the following functions are set up properly in the web browser. Active Script/JavaScript enable There are some control items used with the JavaScript function in the setting pages.
Web browser setting Examples: OS/Browsers Windows XP Professional Internet Explorer v.6.0 ActiveScript setting Select Internet Options from Tools menu on the web browser and then select Security tab and click Customize Level… button. On the security setting window, scroll down and find the Scripting item, make sure that "Enable" is selected in item Active Scripting.
Chapter 7 Appendix Flash Player Add-on setting Select Manage Add-ons... from Tools menu on the web browser. Select "Add-ons currently located in Internet Explorer" from Show pull-down menu. Make sure that the "Shockwave Flash Object" is listed under the item "Enabled". Proxy setting Select Internet Options from Tools menu on the web browser and then select Connection tab and click LAN Settings button.
Web browser setting Netscape Navigator v.7.0 JavaScript Setting Select Preference from Edit m enu on the web browser and then selec t the item Advanced/Scripts & Plugins in the Category column. Make sure that the Enable JavaScript for Navigator is checked. Flash Player enable ENGLISH Flash Player Plug-in setting Select About:Plug-ins from Help menu on the web browser. The plug-ins software provided on the browser are listed on the page.
Chapter 7 Appendix Proxy setting Select Preference from Edit menu on the web browser and then select the item Advanced/ Proxies in the Category column. Properly set up your web browser's the proxy server settings according to the local area network environment to which the projector is connected. - Using proxy server When you use an external internet connection from the local area network, select the item Manual proxy configuration.
Product specification Product specification Type .......................................................... CCM-LX (network unit) LAN interface...................................... Applicant regulation IEEE802.3 (10Base-T) IEEE802.3u (100Base-TX) Data transfer speed 10Mbps/100Mbps Data transfer mode Half Duplex/Full Duplex Terminal 8-pin modular (RJ-45) Network protocol .............................TCP/IP specification TCP/IP Power source ......................................
Chapter 7 Appendix Port specification LAN port specification 8-pin modular connector (RJ-45) 12 3 4 5 6 7 8 Pin No. Signal 1 TX+ Function Transfer data (+) 2 TX- Transfer data (-) 3 RD+ Receive data (+) 4 (not used) 5 (not used) 6 RD- 7 (not used) 8 (not used) 116 Downloaded From projector-manual.com Christie Manuals Receive data (-) CCM-LX User Manual 020-000326-01 Rev.
Q&A Q&A Installation/Access Q Why doesn’t the setting page appear in my web browser? A Following causes are possible. Please check them. 1. The projector does not connect to the network. Check LED indicators status. ( p.17) - Check the connection of LAN cable if the LINK indicator does not illuminate red. - Check the network configuration of the projector if ACT indicator does not illuminate green. 2. Function "Network" in the projector is not set to "ON". Set up by using the projector’s on-screen menu.
Chapter 7 Appendix 3. Enter the projector’s IP address [192.168.0.2] at "Address" column on the Web browser. [Note] Make sure that the proxy setting of your web browser is set "Not use a proxy server". ( p.108) 4. If the login page appears, this product is operating properly. The problems may be in the network configuration of the computer or in the network. Please try to set up the network by following item "Network configuration". ( p.
Q&A Q How can I install several projectors equipped with the network unit? A Install and configure network one by one to avoid the IP address collision each other. ( p.24) To configure the IP address please see item "Network configuration". ( p.20) Q How many projectors can I control with multi-control function? A It has been designed to control up to 100 sets but it depends on the network environment.
Chapter 7 Appendix Q Why does it sometimes take a lot of time to complete the page display? A The display speed of the page depends on the network environment in which both the projector and computer are placed. It may take much time to complete the page display if network traffic is heavy. Please consult your network administrator. You can select the Light mode for displaying pages quickly. ( p.30) Q I use many of the projectors in the network.
Q&A Q What are the rules for IP address assignment? A If the network is constructed with TCP/IP protocol, a unique IP address is required for each piece of network equipment. The following are basic rules of the assignment. Rule1 Do not configure the same IP address to the network equipment in the same network group. Each piece of equipment must be assigned a unique IP address. If the IP address is set [192.168.x.x], the Subnet Mask should be set [255.255.255.0] for example. Rule2 The start address [xxx.
Chapter 7 Appendix Q Can I update the firmware of the network unit. A It is possible to update the firmware through the network. It is required to have a special tool for the updating. For further information please consult your local dealer. The version number of the firmware is indicated on the lower part of the "Initial Setting" page. Network capture Q Why doesn’t the computer screen appear on the projected screen? A 1. Make sure that the input mode of the projector is "Network". 2.
Q&A Network Viewer Q Images from the file server don’t appear on the screen? A 1. Make sure that the input mode of the projector is "Network". 2. Check the account setting of the FTP server. ( p.99) 3. The files in the FTP server must be optimized JPEG and converted by using the File Converter 1 or 2. Please check data format. ( p.89) 4. There are several limitations for image file name and program name. Please check file names and program names. ( p.97) 5.
Downloaded From projector-manual.
Downloaded From projector-manual.
Corporate offices USA – Cypress ph: 714-236-8610 Canada – Kitchener ph: 519-744-8005 Worldwide offices United Kingdom ph: +44 118 977 8000 Hungary/Eastern Europe ph: +36 (0) 1 47 48 100 Beijing ph: +86 10 6561 0240 Germany ph: +49 2161 664540 Singapore ph: +65 6877 8737 Korea ph: +82 2 702 1601 France ph: +33 (0) 1 41 21 44 04 Shanghai ph: +86 21 6278 7708 Japan ph: +81 3 3599 7481 For the most current technical documentation, Downloaded From projector-manual.
