Operation Manual

23
English
No.
Setup time / 16 = each segment of the running time
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
P1 SPEED 2 5 5 5 10 10 5 5 5 3 3 2 5 5 3 2
INCLINE 0 0 1 1 1 1 2 2 2 2 3 3 3 2 2 0
P2 SPEED 2 2 7 2 2 7 7 12 4 4 12 4 4 12 4 2
INCLINE 0 1 2 2 3 3 2 2 3 3 2 2 3 2 2 0
P3 SPEED 2 4 9 9 4 4 8 8 10 10 12 4 4 8 4 2
INCLINE 0 1 2 3 4 5 4 5 4 2 1 2 3 2 1 0
P4 SPEED 2 6 6 6 12 12 12 12 6 6 3 3 3 5 5 2
INCLINE 0 1 2 3 4 5 6 7 6 6 5 4 3 2 1 0
P5 SPEED 2 4 6 12 12 12 3 3 3 3 12 12 12 6 4 2
INCLINE 0 2 4 6 4 2 1 0 1 1 2 2 2 2 3 0
P6 SPEED 2 4 5 5 6 6 8 8 6 6 8 8 6 9 6 2
INCLINE 0 1 3 4 4 3 3 1 2 1 2 1 2 1 2 0
P7 SPEED 2 7 7 9 9 4 4 12 12 4 4 8 8 4 4 2
INCLINE 0 1 1 2 2 3 3 4 4 3 3 2 2 1 1 0
P8 SPEED 2 2 6 6 6 8 9 10 11 12 9 5 5 5 3 2
INCLINE 0 1 2 4 2 1 2 4 2 1 2 4 2 1 2 0
P9 SPEED 2 4 8 10 2 4 8 10 2 4 10 2 4 10 4 2
INCLINE 0 1 2 3 4 5 6 7 8 9 8 6 4 2 1 0
P10 SPEED 2 5 6 7 8 9 10 11 10 9 8 6 7 5 4 2
INCLINE 0 1 2 4 6 6 6 4 4 4 2 2 2 1 1 0
P11 SPEED 2 5 6 7 9 9 6 9 6 9 6 10 6 10 7 2
INCLINE 0 2 2 2 3 3 3 4 4 4 5 5 5
4 4 0
P12 SPEED 2 6 8 10 8 6 4 6 8 12 8 6 8 12 12 2
INCLINE 0 1 1 3 3 5 5 7 7 5 5 3 3 1 1 0
P13 SPEED 2 12 4 12 4 12 4 12 4 12 4 12 4 12 4 2
INCLINE 0 8 10 13 4 8 10 13 4 8 10 13 4 8 10 0
P14 SPEED 2 8 10 12 4 8 10 12 4 8 10 12 4 8 10 2
INCLINE 0 8 12 13 4 8 12 13 4 8 12 13 4 8 12 0
P15 SPEED 2 12 10 8 12 12 10 8 12 12 10 8 12 12 10 2
INCLINE 0 3 4 5 6 8 7 8 8 7 7 6 5 4 3 0
P16 SPEED 2 12 4 12 4 12 4 12 4 12 4 12 4 12 4 2
INCLINE 0 4 5 6 2 4 5 6 2 4 5 6 2 4 5 0
P17 SPEED 2 4 6 8 10 12 12 2 4 6 8 12 12 10 6 2
INCLINE 0 4 6 8 10 12 13 12 13 12 13 10 8 6 4 0
P18 SPEED 2 6 8 4 6 8 4 6 8 4 6 8 4 6 8 2
INCLINE 0 6 8 2 6 8 1 6 8 2 6 8 1 6 8 0
1.9. User-setting programs:
Beside the 18 inner systems, the treadmill setup 3 user-defined programs:
U1, U2, U3.
1. Setting the user-defined program:
Continuously press „program“ key until the expected program (U1/U2/U3)
display in the standby condition, while the „time“ window flash, display
the setting time, press “STEIGUNG+”, “STEIGUNG -” , “KM/H+”, “KM/H
-”to set up expected run time, press „F“ key to enter program parameter,
then set up the first time period parameter, by „ KM/H +“ /“ KM/H -“ key or
shortcut key to set the speed; by „ STEIGUNG +“/“ STEIGUNG -“ key or
shortcut key to set slope; press „mode“ key to finish the first time period
setting, and entering the next time period setting, until all 16 time period
setting. The parameter will be kept permanently until resetting, and all pa-
rameter will not be lost when power off.
2. Selection and start the user-defined program:
In the standby condition, continuously press „program“ key until the ex-
pected user-defined program U1/U2/U3 display, set up the run time, press
„start“ key to turn on the treadmill.
1.10. HRC Programs:
1. There are 3 HRC programs (HRC 1, HRC 2 und HRC 3) with different
max. speed.
HRC 1 max. speed 16km/h, HRC 2 max. speed 18km/h, HRC 3 max.
speed 20km/h
These programs you can pre-enter your own target H.R.
2. Adjusting the HRC programs:
Press program –key to select one of the target H.R. programs HRC 1, HRC
2 or HRC 3. Then press F-key to enter this program and adjust with +/-
km/h speed or +/- % incline keys the age and target H.R.
A. Age: adjustable 13 - 80 years, the default age is 30 years.
B. Target H.R.: adjustable 0.45 (45%) - 0.75 (75%) of the max. H.R. (220-
Age), the default value is 0.6 (60%) of max. H.R.
C. The maximum pulse is: (220-Alter)
1.8. Preset Programs
Each program is divided into 16 sections; the operation time will be evenly
distributed to each program section. Here below is a 18section program
running diagram.