SDS

SAFETY DATA SHEET
Date Revised:
MAR 2015
Supersedes: NOV 2014
SECTION I - PRODUCT AND COMPANY IDENTIFICATION
Christy's® Red Hot Blue Glue® Low VOC
SYNONYMS:
Solvent Cement for PVC Plastic Pipe
SUPPLIER and MANUFACTURER:
T Christy Enterprises, Inc.
655 East Ball Road, Anaheim, CA 92805-5910
Tel. [phone] (North America)
Tel. [phone] (International)
Fax: 86 - 21 - 6428 - 1011
Fax: 86 - 21 - 6428 - 1011
Fax: 86 - 21 - 6428 - 1011
EMERGENCY: Transportation/Medical issues: Tel. [phone] INFOTRAC
SECTION 2 - HAZARDS IDENTIFICATION
Acute Toxicity: Category 4 Acute Toxicity: None Known Flammable Liquid/Aerosol/Gas: Category 2
Skin Corrosion/Irritation: Category 3 Chronic Toxicity: None Known
Carcinogenicity Category 2
Eye:
GHS LABEL: WHMIS CLASSIFICATION: CONTROLLED PRODUCT
Signal Word:
DANGER CLASS B, DIVISION 2 CLASS D, DIVISION 2B
H225 Highly flammable liquid and vapor
H302 Harmful if swallowed
P202 Do not handle until all safety precautions have been read and understood
H319 Causes serious eye irritation
H332 Harmful if inhaled
H335 May cause respiratory irritation
H336 May cause drowsiness or dizziness P270 Do not eat, drink or smoke when using this product.
H351 Suspected of causing cancer
P330 Rinse Mouth
P308+P313 IF exposed or concerned: Get medical adivce/attention
P405 Store locked up
SECTION 3 - COMPOSITION/INFORMATION ON INGREDIENTS
CAS# EINECS # CONCENTRATION
Pre-registration Number % by Weight
Polyvinyl Chloride Resin (PVC) NON/HAZ
Tetrahydrofuran (THF)** (Stabilized) 109-99-9 203-726-8 05-2116297729-22-0000 40 - 65
Methyl Ethyl Ketone (MEK)* 78-93-3 201-159-0 05-2116297728-24-0000 5 - 20
Cyclohexanone 108-94-1 203-631-1 05-2116297718-25-0000 10 - 30
Acetone 67-64-1 200-662-2 05-2116297713-35-0000 0 - 20
All of the constituents of this adhesive product are listed on the TSCA inventory of chemical substances maintained by the US EPA, or are exempt from that listing.
*This chemical is subject to the reporting requirements of Section 313 of the Emergency Planning and Community Right-to-Know Act of 1986 (40CFR372).
SECTION 4 - FIRST AID MEASURES
Contact with eyes: Flush eyes immediately with plenty of water for 15 minutes and seek medical advice immediately.
Skin contact: Remove contaminated clothing and shoes. Wash skin thoroughly with soap and water. If irritation develops, seek medical advice.
Inhalation: Remove to fresh air. If breathing is stopped, give artificial respiration. If breathing is difficult, give oxygen. Seek medical advice.
Ingestion: Rinse mouth with water. Give 1 or 2 glasses of water or milk to dilute. Do not induce vomiting. Seek medical advice immediately.
SECTION 5 - FIREFIGHTING MEASURES
Suitable Extinguishing Media: Dry chemical powder, carbon dioxide gas, foam, Halon, water fog. HMIS NFPA 0-Minimal
Unsuitable Extinguishing Media: Water spray or stream. Health 2 2 1-Slight
Exposure Hazards: Carbon monoxide, carbon dioxide, hydrogen chloride and smoke Flammability 3 3 2-Moderate
Combustion Products: Carbon monoxide, carbon dioxide, hydrogen chloride and smoke Reactivity 1 1 3-Serious
Protection for Firefighters: Self-contained breathing apparatus or full-face positive pressure airline masks. 4-Severe
SECTION 6 - ACCIDENTAL RELEASE MEASURES
Personal precautions: Keep away from heat, sparks and open flame.
Provide sufficient ventilation, use explosion-proof exhaust ventilation equipment or wear suitable respiratory protective equipment.
Prevent contact with skin or eyes (see section 8).
Environmental Precautions: Prevent product or liquids contaminated with product from entering sewers, drains, soil or open water course.
Methods for Cleaning up: Clean up with sand or other inert absorbent material. Transfer to a closable metal containers
Materials not to be used for clean up: Aluminum or plastic containers.
SECTION 7 - HANDLING AND STORAGE
Handling:
Avoid breathing of vapor, avoid contact with eyes, skin and clothing.
Keep away from ignition sources, use only electrically grounded handling equipment and ensure adequate ventilation/fume exhaust hoods.
Do not eat; drink or smoke while handling.
Storage: Store in ventilated room or shade below 27°C (80°F) and away from direct sunlight.
Keep away from ignition sources and incompatible materials: caustics, ammonia, inorganic acids, chlorinated compounds, strong oxidizers and isocyanates.
Follow all precautionary information on container label, product bulletins and solvent cementing literature.
SECTION 8 - PRECAUTIONS TO CONTROL EXPOSURE / PERSONAL PROTECTION
EXPOSURE LIMITS: ACGIH TLV ACGIH STEL OSHA PEL OSHA STEL:
Tetrahydrofuran (THF) #,##
50 ppm skin 100 ppm 200 ppm 250 ppm # Mfg. Recommended Allowable Exposure Limit (AEL): 25 ppm
Methyl Ethyl Ketone (MEK)
200 ppm 300 ppm 200 ppm 300 ppm ## Mfg. Recommended STEL: 75 ppm
20 ppm skin 50 ppm
500 ppm skin
750 ppm 750 ppm 1000 ppm
Engineering Controls: If ventilated cabinet, enclosure or fume hood is necessary, average airflow should be at least 100 FPM (50.8 cm/sec).
Monitoring: Maintain breathing zone airborne concentrations below exposure limits.
Personal Protective Equipment (PPE):
Eye Protection: Avoid contact with eyes, wear splash proof chemical goggles, face shield, safety glasses (spectacles) with brow guards and side shields,
etc. as may be appropriate for the exposure.
Skin Protection: Prevent contact with the skin as much as possible. Polyethylene or PVA coated rubber gloves should be used for frequent immersion.
Use of latex/nitrile surgical gloves or solvent-resistant barrier cream should provide adequate protection when normal adhesive application
practices and procedures are used for making structural bonds.
Respiratory Protection:
Prevent inhalation of the solvents. Use in a well-ventilated room. Open doors and/or windows to ensure airflow and air changes. Use local
exhaust ventilation to remove airborne contaminants from employee breathing zone and to keep contaminants below levels listed above.
With normal use, the Exposure Limit Value will not usually be reached. When limits approached, use respiratory protection equipment.
Health
Precautionary Statements (See Section 15 for all advisory and required precautions)
Christy's® Red Hot Blue Glue® Low VOC PVC Plastic Pipe Cement
Physical
Environmental
GHS CLASSIFICATION:
PRODUCT NAME:
Cyclohexanone
Category 2B
P501 Dispose of contents/container in accordance with local regulations.
P304 + P340 IF INHALED: remove person to fresh air and keep comfortable for breathing.
P271 Use only outdoors or in a well-ventilated area.
Remove contact lenses, if present and easy to do. Continue rinsing.
P201 Obtain special instructions before use.
PRODUCT USE:
Hazard Statements
P210 Keep away from heat, hot surfaces, open flames and other ignition sources. No smoking
P403+P233 Store in a well-ventilated place. Keep container tightly closed.
P301+P312 IF SWALLOWED: Call a POISON CENTER/ doctor if you feel unwell.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes.
P261 Avoid breathing fumes/gas/vapours
P264 Wash hands thoroughly after handling.
P280 Wear protective gloves/ protective/ clothing/ eye protection/ face protection
REACH
Component
Cyclohexanone
FileName: RH RHBV Page 1 of 2