User's Manual

ManualsBrandsChromagic Technologies ManualsElectronicsPIR motion sensor

HSP02 MOTION DETECTOR

The Motion Detector is a Z-Wave

enabled device which is fully compatible with

any Z-Wave

enabled network. Z-Wave

enabled devices displaying the

Z-Wave

logo can also be used with it regardless of the manufacturer, and ours

can also be used in other manufacturer’s Z-Wave

enabled networks. This

Motion Detector can control our modules via controller setting. Inclusion of this

Motion Detector on other manufacturer’s Wireless Controller menu allows remote

turn-on of connected modules when the detector is triggered.

The Motion Detector is designed with two detecting sensors, Passive Infra-Red

(PIR) sensor and light sensor, in order to fulfill the purpose of security and home

automation. When the detector is cooperated with security appliances, it is acting

as a security device by detecting changes in infra-red radiation levels. If a person

moves within or across the device field of vision, a trigger radio signal will be

transmitted to cause full alarm condition in order to frighten intruders away.

Alternatively, when the detector is worked with home automation appliances, the

detector can be set to perform the role of home automation device by detecting both

changes in infra-red radiation levels and percentage of lux levels. Once night falls,

the percentage of ambient illumination is lower than preset value. If a person

moves within or across the device field of vision, a trigger radio signal will be

transmitted so as to turn on the connected lightings for better illumination.

Two mounting methods are provided for varying detection range. The detector can

be mounted on a wall for farther detecting distance but narrower coverage; while for

ceiling mounting, shorter detecting distance can be made but desired coverage can

be expected at user’s disposal.

Product Overview

Include to or Exclude from Z-Wave

Network

In the rear casing, there is a link key which is used to carry out inclusion, exclusion,

association or reset. When the detector is first powered up, the LED flashes on

and off alternately and repeatedly at 2-second intervals. It implies that it has not

been assigned a node ID and cannot work with Z-Wave enabled devices. Please

get familiar with the terms below before starting the operations.

Function Description

Inclusion Add a Z-Wave enabled device (e.g. Motion Detector) to Z-Wave network.

Exclusion Delete a Z-Wave enabled device (e.g. Motion Detector) from the network.

Association After inclusion, you have to define the relationship between devices.

Trough association, device can be assigned as master/slave, and specify

which slave is going to be controlled by which master.

Reset Restore Detector to factory default.

The table below lists an operation summary of basic Z-Wave functions. Please

refer to the instructions for your Z-Wave

Certificated Primary Controller to access

the setup function, and to include/exclude/associate devices.

Function Description Indication

No node ID The Z-Wave Controller does not allocate a

node ID to the unit.

2-second on, 2-second off

1. Have Z-Wave Controller entered

inclusion mode.

Inclusion

2. Pressing link key 3 times within 1.5

second will enter inclusion mode.

The Detector will stay “awake” for 5

minutes to allow time for setting and

device status enquiring.

Detector beeps when link

key is pressed.

1. Have Z-Wave Controller entered

exclusion mode.

Exclusion

2. Pressing link key 3 times within 1.5

second will enter exclusion mode.

The Detector will stay “awake” for 5

minutes to allow time for setting and

device status enquiring.

Detector beeps when link

key is pressed.

1. Press link key 3 times within 1.5

second.

Detector beeps when link

key is pressed.

2. Within 1 second, press and hold link

key until beep stops.

A long beep is sounded for

5 seconds.

Reset

3. IDs are excluded and all of preset

value will be reset to factory default.

2-second on, 2-second off

Summary of content (7 pages)

PAGE 1
Include to or Exclude from Z-WaveTM Network HSP02 MOTION DETECTOR In the rear casing, there is a link key which is used to carry out inclusion, exclusion, association or reset. When the detector is first powered up, the LED flashes on and off alternately and repeatedly at 2-second intervals. It implies that it has not been assigned a node ID and cannot work with Z-Wave enabled devices. Please get familiar with the terms below before starting the operations.
PAGE 2
Function Association Description 1. Have Z-Wave Controller entered association mode. Indication 2. When pressing link key 3 times within 1.5 seconds will enter association mode. Detector beeps when link key is pressed. Installation Ensure that the system is in Test Mode. 1. 3. There are two groupings – 1 and 2. Refer to Z-Wave’s Grouping as described on page 4. Including a node ID allocated by Z-Wave Controller means inclusion. Excluding a node ID allocated by Z-Wave Controller means exclusion.
PAGE 3
Settings Warm-Up It will take approximately 2 minutes to warm up after battery has been connected. During this period, the red LED will flash in every 3 seconds. When the red LED turns on steadily for 5 seconds, it implies warm-up procedure is completed and the detector is ready for detection. Operation Wall Mounting 1. By walking into a protected area within coverage of 110 degrees, the detector will now be triggered each time the detector senses movement.
PAGE 4
Z-Wave system or someone that has computer software running a Z-Wave controller. Please get familiar with software of Z-Wave controller before getting started. intrusion event. Once the movement is stopped, SENSOR_ BINARY_REPORT will be sent again to the associated devices.
PAGE 5
2-6 On-Off Duration time of use. If movements cannot be detected sensitively, simply adjust the sensitivity level with Configuration Parameter #3. This parameter can be configured with the value of 1 through 10, where 1 means low sensitivity and 10 means highest sensitivity. Function Sensitivity Level Parameter Number 3 Size 1 Range 1~10 The function of on-off duration setting will be useful if the detector is connected with a module or lighting.
PAGE 6
0 seconds and 194 days respectively. Allowable interval among each wakeup interval is 1 second, such as 60, 61, 62 …. The detector does not stay awake for 10 minutes Check if detector is out of order Note: The default value is 1 day, which implies that the detector awakes and sends the Wakeup Notification Command to the set node every day. Please make sure link key is pressed 3 times within 1.5 sec. If detector still fails to stay awake for 10 seconds, repeat this step until it is succeeded.
PAGE 7
following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.