SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 9 ▫ Sentry Key Engine Immobilizer — If Equipped . 9 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .12 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .12 ▫ Floor Shift Ignition Interlock System . . . . . . . . .13 䡵 Glove Compartment Lock . . . . . . . . . . . . . . . . .13 䡵 Illuminated Entry System . . . . . . . . . . . . . . . . .14 䡵 Door Locks . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Transmitter Linked To Memory Programming . .21 ▫ Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . .28 ▫ General Information . . . . . . . . . . . . . . . . . . . .22 ▫ Seat Belts And Pregnant Women . . . . . . . . . . . .32 ▫ Transmitter Battery Service . . . . . . . . . . . . . . .23 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . .32 䡵 Security Alarm System . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9 A WORD ABOUT YOUR KEYS You can insert the double sided keys into the locks with either side up. have been programmed to the vehicle can be used to start and operate the vehicle for more than the two second validation time period. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys only from your dealer. Ask your dealer for these numbers and keep them in a safe place.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the Sentry Key Immobilizer System indicator light comes on during normal vehicle operation (it has been running for longer than 10 seconds) a fault has been detected in the electronics and the vehicle should be serviced as soon as possible. NOTE: • The Sentry Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Customer Key Programming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed. NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer. Customer Key Programming You can program new keys to the system if you have two valid keys by doing the following: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Ignition Key Removal Place the shift lever in Park and make sure that the shift knob push-button (vehicles with floor shift) is in the out position. Turn the key to the Lock position and remove the key. NOTE: If you try to remove the key before you place the lever in Park, the key may become trapped temporarily in the key cylinder. If this occurs, turn the key clockwise slightly, then remove the key as described.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Floor Shift Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK and the shift knob push button is out. It also prevents shifting out of PARK unless the key is in the OFF or RUN positions. 2 GLOVE COMPARTMENT LOCK The glove box lock has been designed so that the key can be inserted only about half way. Do not force the key past this point.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ILLUMINATED ENTRY SYSTEM The interior lights will come on when you unlock the vehicle with the remote keyless entry or central unlock. They will remain on for about 30 seconds after all doors are closed then fade to off. The lights also will fade to off if you turn on the ignition after you close all the doors. DOOR LOCKS Power Door Locks There is a door lock switch on each front door trim panel. Press this switch to lock or unlock the four doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 If you press the door lock switch while the keys are in the ignition switch, with the ignition switch in the ACC, LOCK, or OFF position, and the driver’s door is open, the doors will not lock. A chime will sound as a reminder to remove the keys. WARNING! For personal security and safety in the event of an accident, lock the vehicle doors as you drive and when you park and leave the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE “Child-Protection” Lock System (Rear Doors) To provide a safer environment for small children riding in the rear seat, the rear doors of your vehicle have the “child-protection” door lock system. NOTE: For emergency exit with the system engaged, move the lock plunger up (unlocked position), lower the window and open the door with the outside door handle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 3. vehicle speed is above 15 m.p.h. (24 km/h), 3. Depress the power door lock switch to lock the doors. 4. the accelerator pedal is depressed. 2 The Automatic Door Locks can be disabled or re-enabled by performing the same following procedure: 1. Close all doors and place the key in the ignition. 2. Cycle the ignition switch between OFF and ON/RUN and back to OFF 4 times ending up in the OFF position. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Unlock on Exit (Only Available if Automatic Door Locks Enabled) This feature will unlock all the doors when the driver’s door is opened and the ignition switch is in the LOCK position. This function is disabled as delivered from the factory. Automatic Unlock on Exit can be enabled or disabled by performing the following procedure: 1. Close all doors and place the key in the ignition. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 To unlock the doors: Press and release the unlock button on the transmitter. NOTE: The system may be programmed to unlock all the doors upon the first press of the Unlock button. To toggle between the first press unlock of driver’s door to unlock of all doors, perform the following procedure: 1. Press and hold the Unlock button on the transmitter. 2. Continue to hold the Unlock button, wait at least 4 but no longer than 10 seconds, then press the Lock button.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enable/Disable Trunk Press and Hold: The transmitter can be programmed to unlatch the trunk immediately upon activation of the Trunk button (without pressing and holding) by performing the following procedure: 1. Press and hold the Unlock button on the transmitter. To Use The Panic Alarm: Press and hold the Panic button to activate the alarm. Press and hold the Panic button or unlock the door with the key to deactivate the alarm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 1. With the vehicle in Park, turn the Ignition switch to the ON position. release the lock and unlock buttons simultaneously. You will hear a chime after each transmitter has been successfully programmed. You will have 30 seconds to finish programming all new transmitters. A chime will sound when the 30 seconds is over or the ignition switch is turned to the Lock position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Press and release the Set (S) button on the memory seat switch, then press and release memory button 1 or 2. 3. Within ten seconds of completing step 2, press and release the Lock button on the transmitter. This will link the transmitter to the desired memory setting. NOTE: Your transmitters may be unlinked to your memory settings by following the procedure above except pressing the Unlock button on the transmitter in step 3 above.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Transmitter Battery Service The recommended replacement battery is DL 2016 or its equivalent. • Pry the transmitter halves apart with a dime or similar object. Make sure not to damage the rubber gasket during removal. • Reassemble the transmitter case. Snap the halves together and test transmitter operation. SECURITY ALARM SYSTEM The system monitors the doors, trunk key cylinder, and ignition for unauthorized operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To set the alarm: 1. Remove the keys from the ignition switch and get out of the vehicle. 2. Lock the door using either the door key, power door lock switch, or the Keyless Entry Transmitter and close all doors. 3. The SET light on the top of the instrument panel will flash rapidly for 16 seconds. This shows that the system is arming. If the light comes on but does not flash, the system is still armed, but there is a problem in the trunk circuit.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Security System Manual Override The system will not arm if you lock the doors using the manual lock control. POWER WINDOWS Window controls on the driver’s door control all door windows. The driver’s window switch has an Auto Down feature. Press the window switch past the detent, release, and the window will go down automatically. Press the switch a second time in either direction to stop the window.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE TRUNK LID RELEASE You can open the trunk lid from inside the vehicle by pressing the switch on the left side of the instrument panel. The transmission must be in Park before the switch will operate. TRUNK SAFETY WARNING WARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 Trunk Emergency Release The trunk of your vehicle is equipped with an emergency release handle. It is located on the inside of the trunk lid, near the latch, and is coated so that it glows in a darkened trunk. Pull on the handle to open the trunk. OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision which includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives. And they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the front seat. Center Console removed from following illustrations 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt go around your lap. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is very dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your dealer and have it fixed. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front seats, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push the lever above the webbing upward to release the anchorage, and then move it up or down to the position that serves you best. In the rear seat, move toward the center of the seat to position the belt away from your neck.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers are designed to open only when the airbags are inflated.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 be secured in the rear seat in child restraints or beltpositioning booster seats appropriate for the size and age of the child. Older children who do not use child restraints or beltpositioning booster seats should ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag System Components The airbag system consists of the following: • ACM (Airbag Control Module) • AIRBAG Readiness Light • Driver and Passenger Front Airbags • Optional Driver and Passenger Side Airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 then turns the light off. If it detects a malfunction in any part of the system, it turns on the light either momentarily or continuously. through vent holes in the sides of the airbag. In this way the airbags do not interfere with your control of the vehicle. WARNING! • The Knee Impact Bolsters help protect the knees and position you for the best interaction with the airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 • The side impact airbag control module monitors the readiness of the electronic parts of the system whenever the ignition switch is in the “START” or “RUN” positions. These include all of the items listed above except for the AIRBAG light (which is controlled by the frontal airbag system). • In moderate to severe side collisions, the side airbag inflator on the crash side of the vehicle is triggered, releasing a quantity of nontoxic gas.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light You will want to have the airbags ready for your protection in an impact. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately. • The AIRBAG light does not come on or flickers during the 6 to 8 seconds when the ignition switch is first turned on. • The light remains on or flickers after the 6 to 8 second interval.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Infants and Child Restraints • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and “convertible” child seats. • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may not work when you need it. • Buckle the child into the seat according to the seat manufacturer’s directions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt behind their back or under their arm. LATCH – Child Seat Anchorage System (Lower Anchors and Tether for CH ildren) Your vehicle’s rear seat is equipped with the child restraint anchorage system called LATCH.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provided with the child restraint system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To attach a child restraint tether strap: 1. Lift the cover over the anchor directly behind the seat where you are placing the child restraint. 3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and remove slack in the tether strap according to the child restraint manufacturer’s instructions. WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 ENGINE BREAK-IN RECOMMENDATIONS The engine in your new vehicle does not require a long break-in period. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration, within the limits of local traffic laws, contributes to a good break-in. Wide open throttle acceleration in low gear can be detrimental and should be avoided.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE must remain open, close all windows. Adjust the heating or cooling system to force outside air into the vehicle. Set the blower at high speed. Safety Checks You Should Make Inside the Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Console Features . . . . . . . . . . . . . . . . . . . . . . .53 ▫ Power Seats . . . . . . . . . . . . . . . . . . . . . . . . . .57 䡵 Cup Holders . . . . . . . . . . . . . . . . . . . . . . . . . .53 ▫ Power Reclining Seats . . . . . . . . . . . . . . . . . . .58 ▫ Front Seat Cupholders . . . . . . . . . . . . . . . . . . .53 ▫ Driver’s Seat Glide –To – Exit Feature . . . . . . . .58 䡵 Coat Hook . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ To Turn The Interior Lights On . . . . . . . . . . . . .64 ▫ Passing Light . . . . . . . . . . . . . . . . . . . . . . . . .68 ▫ Battery Saver Feature—Interior Lights . . . . . . . .64 ▫ Windshield Wipers And Washers . . . . . . . . . . .69 ▫ Instrument Panel Lighting . . . . . . . . . . . . . . . .65 ▫ Speed Sensitive Intermittent Wipers System . . . .69 ▫ Front Map/Reading Lights . . . . . . . . . . . . . . .65 䡵 Tilt Steering Column . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 51 ▫ Programming The Universal Transceiver . . . . . .76 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . .87 ▫ “Rolling Code” Programming . . . . . . . . . . . . .77 ▫ Sun Roof Maintenance . . . . . . . . . . . . . . . . . . .87 ▫ Canadian Programming/Gate Programming . . .79 䡵 Electronic Vehicle Information Center (EVIC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .88 ▫ Operation . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Trip Odometer (ODO) . . . . . . . . . . . . . . . . . . 103 ▫ Automatic Compass Calibration . . . . . . . . . . . 104 ▫ Elapsed Time (ET) . . . . . . . . . . . . . . . . . . . . . 103 ▫ Manual Compass Calibration . . . . . . . . . . . . . 104 ▫ C/T Button . . . . . . . . . . . . . . . . . . . . . . . . . 103 ▫ Outside Temperature . . . . . . . . . . . . . . . . . . . 105 ▫ Compass/Temperature Display . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 53 CONSOLE FEATURES CUP HOLDERS Front Seat Cupholders The cupholders are located in the forward edge of the console. Press the forward edge of the console to release the cupholders. Press the cupholder back into the console when they are no longer needed. The center console/armrest has a tissue holder and a pencil holder mounted on the underside of the cover.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE COAT HOOK The coat hook is located next to the Rear Seat Reading/ Courtesy Light Switch. Pull the hook down for access. MIRRORS Adjusting The Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustment. Automatic Dimming Mirror Feature This mirror will automatically adjust for annoying headlight glare from vehicles behind you.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 55 Electric Remote Control Mirrors NOTE: Pre selected power mirror positions (for the driver seat only) can be controlled by the Memory Seat Feature. Refer to the Seats section which follows. Press the L or R button located on the driver’s door panel for Left or Right mirror selection. NOTE: This feature is most effective when left in the ON position. Heated Remote Control Mirrors These mirrors are heated to melt frost or ice.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Place the mirror switch in the neutral (center) position to prevent accidental changing of the mirror setting. Supplemental Indicators — 300M Special Only The 300M Special is equipped with Supplemental Indicators on each of the side mirrors. When using the Multifunction Control lever to signal, small lights in the side outside mirrors will flash designating the direction of the turn.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 57 On vehicles equipped with an EVIC (Electronic Vehicle Information Center), these functions can be selected at the EVIC using the Customer Programmable Features. Refer to EVIC-Customer Programmable Features for details. 3 Illuminated Vanity Mirrors An illuminated vanity mirror is on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lamps turn on automatically. Closing the mirror cover turns off the lamps.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under a power seat as it may cause damage to the seat controls. Power Reclining Seats The recliner control is on the outboard side of the seat. WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 59 NOTE: On vehicles equipped with an EVIC (Electronic Vehicle Information Center), these functions can be selected at the EVIC using the Customer Programmable Features. Refer to EVIC-Customer Programmable Features for details. Lumbar Support This feature allows you to increase or decrease the amount of lumbar support. Turn the control lever forward to increase and rearward to decrease the desired amount of lumbar support.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memory Feature This feature allows the driver to recall one of two pre-selected seat/outside mirror settings as well as radio station preset buttons. The radio display will show which memory position is being recalled. The memory feature switch is located on the outboard side of the driver’s seat, next to the heated seat switch. To Set The Memory Feature: 1. Use the seat and driver mirror switches to adjust the seat and driver mirror to the desired positions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 61 Programming the Remote Keyless Transmitter for the Memory Feature Your remote transmitters can be programmed to return the driver’s seat, mirror, and radio presets to the saved position when the Unlock button is pressed and released. To program your transmitters, perform the following: 1. Insert the key into the ignition and turn the key to the Run position. 2. Adjust the seat and side view mirror to the desired position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjustable restraints should be adjusted so that the upper edge is as high as practical. Folding Rear Seat The head restraints have a locking button which must be pushed in to lower the head restraint. The restraints may be raised without pushing in the button. The rear seatbacks can be folded forward to provide an additional storage area.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 63 WARNING! The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion. They could be seriously injured in an accident. Children should be seated and using the proper restraint system. TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then lift up on the catch located under the front edge of the hood, near the center. WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. INTERIOR LIGHTS To Turn The Interior Lights On: Rotate the Dimmer Control upward to the second detent. Rotate the switch downward to turn the interior lights off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65 NOTE: The map lights or reading lights that are manually switched on will not turn off automatically. Instrument Panel Lighting The brightness of the instrument panel lighting can be regulated by rotating the dimmer switch. on during the daytime such as in a parade or a funeral procession. To activate this feature, rotate the Dimmer Control upward to the first detent. Front Map/Reading Lights These lights are mounted between the sun visors.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE EXTERIOR LIGHTS Headlights And Parking Lights When the headlight switch is turned clockwise from Off to the first position, the parking lights, taillights, side marker lights, license plate light and instrument panel lights are all turned on. The headlights turn on when the switch is turned to the second position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 Automatic system off, turn the headlight switch clockwise, to the off position. The engine must be running before the headlights will come on in the automatic mode. NOTE: The Automatic Headlight System will turn on the headlights if it detects that the windshield wipers have been in operation for more than 10 seconds. NOTE: Your 300M Special vehicle may be equipped with high intensity headlights (HID).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights (Canada Only) The headlights are on at a dimmer level whenever the vehicle is started and the parking brake is released. The lights remain on until the ignition switch is turned OFF. MULTIFUNCTION CONTROL LEVER Turn Signals The arrows on each side of the instrument cluster flash to show operation of the front and rear turn signal lights. If either light flashes at an extremely fast rate, check for a defective outside light bulb.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 Windshield Wipers And Washers The wipers and washers are operated by a switch in the control lever. Turn the end of the handle to select the desired wiper speed. If the button is pushed while in the OFF position, the wipers will cycle twice. WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Vehicle speed is monitored to calculate wiper delay intervals. The delay between cycles is shortened when the vehicle is moving above 10 m.p.h. (16 km/h) and lengthened below 10 m.p.h. (16 km/h). TILT STEERING COLUMN To tilt the column, pull the small lever below the turn signal control toward you and move the wheel up or down, as desired. Release the lever to lock the wheel firmly in place.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 ELECTRONIC SPEED CONTROL This device can be engaged to take over the accelerator operation at speeds between 30 mph (48 km/h) and 85 mph (137 km/h). The controls are mounted on the steering wheel. To turn the Traction Control System On, press the switch until the TRAC OFF light in the instrument cluster turns off. NOTE: Traction Control System comes on each time the ignition switch is turned On.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate: Push the ON/OFF button to turn the system ON. The CRUISE light in the instrument cluster will illuminate when the system is ON. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 To Resume Speed: To resume a previously set speed, push and release the ACCEL/RESUME button. Resume can be used at any speed above 25 mph (40 km/h). To Accelerate For Passing: Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. To Vary The Speed Setting: When the speed control is engaged, speed can be increased by pressing and holding the ACCEL/RESUME button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE downshift again to second gear. The transmission will upshift as the vehicle reaches the top of the hill. When Descending A Hill If vehicle speed rises 3 mph (5 km/h) over the Speed Control SET speed, the transmission will downshift to third gear. This provides engine braking to keep vehicle speed under control. The transmission will not downshift below third gear to control vehicle overspeed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 The dome/reading lights illuminate when a door is opened or when the interior lights are turned on by rotating the dimmer control located on the multi-function lever. The reading lights are activated by pressing on the recessed area of the corresponding lens. NOTE: The dome/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features it could cause injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 NOTE: Step 2 does not have to be followed to program additional hand held transmitters. 3. Choose one of the three buttons to train. Place the hand held controller one to three inches from the universal transceiver while keeping its indicator light in view. NOTE: Some entry gates and garage door openers may require you to replace step 4 with the procedures listed under Canadian Programming. 5.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE On garage door openers with the “Rolling Code” feature, the transmitter code changes after each use to prevent the copying of your code. difficulty in locating the training button, check your garage door opener manual, or call 1-800-355-3515 or, on the Internet, at www.homelink.com. To check if your device is protected by a “Rolling Code” system: 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Canadian Programming/Gate Programming Canadian frequency laws, and the technology of some entry gates, require you to press and release the hand held transmitter button every two seconds during programming Continue to press and hold the Universal Transceiver button while you press and release the hand held transmitter button until the frequency signal has been learned.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Security If you sell your vehicle, be sure to erase the frequencies. To erase all of the previously trained frequencies, hold down both outside buttons until the green light begins to flash. This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Contact HomeLink威 at 1–800–355–3515 for safety information or assistance or on the internet at www.homelink.com.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Erase the factory test codes by pressing and holding channels button one and three, of the universal transceiver, until CLEARED CHANNELS displays (about 20 seconds). Release the buttons. 3. Choose one of the three universal transceiver buttons to program. Place the hand-held controller at the lower left corner of the display and approximately 1 to 3 inches away from the surface of the universal transceiver keeping the display in view. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 NOTE: In Canada, D.O.C. regulations require many hand-held transmitters to stop transmitting after two seconds. On these hand-held transmitters, transmission will stop even though the light on the hand-held transmitter stays lit. If you have one of these hand-held transmitters, you should press and release the hand-held transmitter button every two seconds without releasing the universal transceiver button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. When the display indicates TRAINED, and the previous programming for the button has now been erased and a new device has been programmed to the button. This procedure will not affect any other programmed buttons. Multiple security code (rolling code) garage door openers and other devices which are ⴖcode protectedⴖ and manufactured after 1995, may be determined by the following: Operation To operate, simply press the desired universal transceiver button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 3. Press the programming button on the garage door opener motor head unit (which activates the programming light). 4. Firmly press and release the programmed universal transceiver button. Press and release the universal transceiver button a second time to complete the programming process. (Some garage door openers may require you to do this procedure a third time to complete the programming.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the two following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference that may be received including interference that may cause undesired operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 The sunshade can be opened manually. It will also open as the sun roof opens. The sunshade cannot be closed if the sun roof is open. WARNING! In an accident, there is a greater risk of being thrown from a vehicle with an open sun roof. You could also be seriously injured or killed. Always fasten your seatbelt properly and make sure all passengers are properly secured too. Do not allow small children to operate the sun roof.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED • MEMORY SEAT DISABLED VEHICLE (not in Park) • LEFT FRONT LOW PRESSURE • LEFT FRONT HIGH PRESSURE • RIGHT FRONT LOW PRESSURE • RIGHT FRONT HIGH PRESSURE • LEFT REAR LOW PRESSURE • LEFT REAR HIGH PRESSURE • RIGHT REAR LOW PRESSURE • RIGHT REAR HIGH PRESSURE The electronic vehicle information center (EVIC), when the appropriate conditions exist, displays the following messages and symbols.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 Tire Pressure Monitor System — If Equipped The Tire Pressure Monitor (TPM) system uses wireless technology to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem transmit tire pressure readings to a receiver located in the overhead console. CAUTION! The TPM system is designed to monitor your tire pressure and will not function as a tire pressure gauge while adjusting the pressure in your tires.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: This display will return 60 seconds after either the C/T, MENU, STEP, or RESET button is pressed. If a tire is low or high, you should correct your tire inflation pressure as soon as possible and inspect all of your tires. Refer to “Starting and Operating, Tires Section, Tire Inflation Pressures” for more details. Once the low or high tire pressure message has occurred, it will continue to blink until the tire pressure is corrected. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: Customer Programmable Features Press the MENU button until one of the display choices following appears: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Language When in this display you may select one of five languages for all display nomenclature, including the trip computer functions. Press the STEP button while in this display selects English, Francaise, Deutsch, Italiano, or Espanol. As you continue the displayed information will be shown in the selected language. US or Metric Pressing the STEP button when in this display selects US or Metric.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Remote Unlock Driver’s Door 1st When this feature is selected only the driver’s door will unlock on the first press of the remote keyless entry unlock button and require a second press to unlock the remaining locked doors. When REMOTE UNLOCK ALL DOORS is selected all of the doors will unlock at the first press of the remote keyless entry unlock button. Pressing the STEP button when in this display will select DRIVER’S DOOR 1ST or ALL DOORS.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlamp On With Wipers (Available with Auto Headlights Only) When this feature is selected and the headlight switch has at least once been moved to the AUTO position, the headlights will turn on when the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on in this way. Pressing the STEP button when in this display will select “Yes” or “No.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Tilt Mirrors Down When this feature is selected, and the vehicle is placed in reverse, the driver’s exterior mirror will tilt downward to improve visibility of rear wheel area. Once reverse is disengaged, the driver’s exterior mirror will return to it’s original position. Pressing the STEP button when in this display will select “YES” or “NO”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When this feature is selected, the TPM system will start the retraining procedure. Pressing the STEP button when in this display will select “Yes” or “No”. Then press Menu button to enter selection. The following describes how to use this feature: 1. Locate the training magnet under the spare tire cover (shaped like a doughnut). 2. Press the MENU button until RETRAIN TIRE SENSORS is displayed. 3. Press the STEP button to select YES to retrain the TPM sensor. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 7. Repeat step 6 working clockwise around the vehicle (Left Front, Right Front, Right Rear, Left Rear, Spare) until all five TPM sensor positions are trained. 8. Return magnet to storage location. If the display reads TRAINING COMPLETE, pressing either the STEP, C/T, RESET, or MENU buttons will exit the training mode. If the display reads TRAINING ABORTED, move the vehicle ahead at least 1 foot (30 cm) and complete steps 1–8 again.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass/Temperature/Trip Computer This display provides the outside temperature, one of the eight compass headings to indicate the direction the vehicle is facing, and vehicle trip information. The compass and temperature display is the normal display. When the C/T button is pressed or the customer programmable features have been “stepped through” the compass/temperature display returns.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Elapsed Time Shows the accumulated ignition ON time since the last reset. Miles to Service Shows the distance remaining to require service. NOTE: This display can be reset to the set service interval by pressing and holding the RESET button for 3 seconds. Tire Pressure Display — If Equipped Shows the current pressure of all 4 road tires. Average Fuel Economy Shows the average fuel economy since the last reset.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Tires heat up during normal driving conditions. Heat will cause the tire pressure to increase from 2 to 6 psi (14 to 41 kPa) during normal driving conditions. Refer to “Tire Inflation Pressures” in Starting and Operating, About Your Tires Section for additional information. Blank Screen Shows a blank screen. Pressing the STEP button returns to the compass and temperature display.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 3 Compass Variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set according to the Compass Variance Map.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press the RESET button approximately five seconds. The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Global Reset If the RESET button is pressed twice within 3 seconds while in any of the 3 resetable displays, the Global Reset button will reset all 3 displays. Step Button Use this button to choose or cycle through the five trip conditions. Average Fuel Economy (AVG ECO) This display shows the average fuel economy since the last reset. Distance To Empty (DTE) This display shows the estimated distance that can be traveled with the fuel remaining in the tank.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Compass Calibration The self calibrating feature of the compass eliminates the need to calibrate the compass for normal conditions. During a short initial period, the compass may appear erratic and the CAL symbol will appear on the display. The CAL symbol may also appear after the vehicle is subjected to a high level of magnetism.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Outside Temperature Because engine temperature can increase the displayed temperature, temperature readings are slowly updated when vehicle speed is below 20 mph (30 km/h). ELECTRICAL POWER OUTLETS Your vehicle may be equipped with two power outlets. The primary power outlet is located in the forward portion of the center console and in the lower center of the instrument panel. Accessories powered through this outlet are protected by a 15 amp fuse.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Move the fuse slightly right and insert it in the fuse #6 “BAT” location in the fuse block. • Reinstall the fuse cover. There may be an additional power outlet, if equipped, inside and on the back side of the bin below the armrest. This power outlet is available for accessory power only and may not be converted to a cigar lighter. The power outlet is powered continuously by the battery. Accessories on this outlet are protected by a 15 amp fuse.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instruments And Controls . . . . . . . . . . . . . . . . 111 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . 112 䡵 Instrument Cluster Description . . . . . . . . . . . . 113 䡵 Setting The Analog Clock . . . . . . . . . . . . . . . . 118 䡵 Electronic Digital Clock . . . . . . . . . . . . . . . . . 118 ▫ Clock Setting Procedure . . . . . . . . . . . . . . . . . 118 䡵 Radio General Information . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Scan Button . . . . . . . . . . . . . . . . . . . . . . . . . 122 ▫ EJT CD (Eject) Button . . . . . . . . . . . . . . . . . . 125 ▫ To Set The Radio Push-Button Memory . . . . . . 122 ▫ FF/Tune/RW Button . . . . . . . . . . . . . . . . . . . 125 ▫ To Change From Clock To Radio Mode . . . . . . 122 ▫ Program Button 4 (Random Play) . . . . . . . . . . 125 ▫ Operating Instructions — Tape Player . . . . . . . 123 ▫ Mode . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 109 ▫ Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 䡵 Satellite Radio — If Equipped . . . . . . . . . . . . . 137 ▫ Fade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 ▫ System Activation . . . . . . . . . . . . . . . . . . . . . 137 ▫ Bass And Treble Tone Control . . . . . . . . . . . . 128 ▫ Electronic Serial Number/Sirius Identification Number (ENS/SID) . . . . . . . . . . . . . . . . . . . . 137 ▫ AM/FM Selection . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Loading The CD Changer . . . . . . . . . . . . . . . 140 ▫ Playing Discs . . . . . . . . . . . . . . . . . . . . . . . . 140 ▫ Seek Button . . . . . . . . . . . . . . . . . . . . . . . . . 141 ▫ FF/Tune/RW . . . . . . . . . . . . . . . . . . . . . . . . 141 ▫ Mode Button . . . . . . . . . . . . . . . . . . . . . . . . 141 ▫ Program Button 1 . . . . . . . . . . . . . . . . . . . . . 141 ▫ Program Button 4 (Random Play) . . . . . . . . . . 141 ▫ Program Button 5 . .
UNDERSTANDING YOUR INSTRUMENT PANEL 111 INSTRUMENTS AND CONTROLS 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER
UNDERSTANDING YOUR INSTRUMENT PANEL 113 INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gauge When the ignition is in the ON position, the pointer will show the level of fuel remaining in the tank. 2. Low Fuel Warning Light When the fuel level drops to about 2 gallons (8 liters), the Low Fuel symbol will light and remain lit until fuel is added. A warning chime will sound when the light comes on. 3. Low Oil Pressure Light This light indicates low engine oil pressure.
UNDERSTANDING YOUR INSTRUMENT PANEL 7. Turn Signal Indicators The arrow will flash in unison with the exterior turn signal, when using the turn signal lever. 8. High Beam Indicator This light shows that the headlights are on high beam. Pull the turn signal lever towards the steering wheel to switch the headlights from high or low beam. 12. Low Washer Fluid Light This symbol will light whenever the fluid reservoir is less than 1/4 filled.
UNDERSTANDING YOUR INSTRUMENT PANEL 115 If the pointer rises to the “H” mark, stop the vehicle and turn off the engine until the problem is corrected. CAUTION! Continuing to drive with an overheated engine cooling system can cause damage to the engine or other components. There are steps that you can take to slow down an impending overheat condition. If your air conditioning is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat.
UNDERSTANDING YOUR INSTRUMENT PANEL have it replaced. If the light stays on, or comes on while driving, have the system checked by an authorized dealer. 19. Odometer/Trip Odometer Shows the total distance the vehicle has been driven. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven.
UNDERSTANDING YOUR INSTRUMENT PANEL 117 If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes. The warning light should be checked frequently to assure that it is operating properly. This can be done by turning the ignition switch to START. The light should come on. 23. Brake System Warning Light The dual brake system provides a reserve braking capability if a failure occurs in a portion of the hydraulic system.
UNDERSTANDING YOUR INSTRUMENT PANEL SETTING THE ANALOG CLOCK To set the analog clock at the top center of the instrument panel, press and hold the plus (+) or minus (-) buttons until the setting is correct. ELECTRONIC DIGITAL CLOCK When the radio is on, pressing the TIME button will allow you to select between displaying actual time continuously or information related to the mode which the radio is in (i.e. in Radio mode, the radio frequency is displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL 119 Two Types of Signals There are two basic types of radio signals... AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary... and FM or Frequency Modulation, in which the frequency of the wave is varied to carry the sound. Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception.
UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch, Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. The volume will be displayed and continuously updated while the button is pressed. Seek Button (Radio Mode) Press and release the Seek button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down.
UNDERSTANDING YOUR INSTRUMENT PANEL 121 Program Type Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather Radio Display Rel Talk Rock Soft Soft Rck Soft R&B Sports Talk Top 40 Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL Tone Control Slide the Bass and/or Treble controls up or down to adjust the sound for the desired tone. The treble, and bass will be displayed and continuously updated while the slide is moved. AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received.
UNDERSTANDING YOUR INSTRUMENT PANEL 123 Operating Instructions — Tape Player Insert the cassette with the exposed tape side toward the right and the mechanical action of the player will gently pull the cassette into the play position. NOTE: When subjected to extremely cold temperatures, the tape mechanism may require a few minutes to warm up for proper operation. Sometimes poor playback may be experienced due to a defective cassette tape. Clean and demagnetize the tape heads at least twice a year.
UNDERSTANDING YOUR INSTRUMENT PANEL Changing Tape Direction If you wish to change the direction of tape travel (side being played), press the PTY button. The lighted arrow in the display window will show the new direction. Metal Tape Selection If a standard metal tape is inserted into the player, the player will automatically select the correct equalization and the 70 symbol will appear in the display window.
UNDERSTANDING YOUR INSTRUMENT PANEL 125 NOTE: • You may eject a disc with the radio OFF. The ignition switch must be in the ON or ACC position to insert a disc with the radio OFF. • If you insert a disc with the ignition ON and the radio OFF, the CD will automatically be pulled into the CD Player and the display will show the time of day. If you insert a disc with the ignition OFF, the display will show the time of day for about 5 seconds, then go out.
UNDERSTANDING YOUR INSTRUMENT PANEL MODE Press the MODE button to select between the tape player, CD player, or satellite radio (if equipped). Scan Button Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. To select Satellite Radio (if equipped), press the MODE button until the word SIRIUS appears.
UNDERSTANDING YOUR INSTRUMENT PANEL 127 NOTE: When first learning the control functions, the user should set the controls as shown in the following list. Tone Controls…As illustrated. Speaker Control…Centered. Power Button The volume control/power button pops out when pressed, this turns the sound system ON in the mode last used. Pushing the button back in turns the sound system OFF.
UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice.
UNDERSTANDING YOUR INSTRUMENT PANEL 129 Cassette Player Features With ignition OFF and the sound system OFF, you can eject the tape cassette by pushing the EJECT button. You can turn the tape player ON by inserting a cassette or activating the MODE button (with a cassette in the radio), but only when the ignition and radio are on. Each time a cassette is inserted the tape player will begin playing on the side of the cassette that is facing up in the player.
UNDERSTANDING YOUR INSTRUMENT PANEL display. Each time a tape is inserted the Dolby will turn ON. * “Dolby” noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. Dolby and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. CD Changer Control Capability — If Equipped This radio is compatible with a remote mounted CD changer available through Mopar Accessories.
UNDERSTANDING YOUR INSTRUMENT PANEL 131 CD HOT will pause the operation. Play can be resumed when the operating temperature is corrected or another MODE is selected. An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following reasons: • Excessive vibration • Disc inserted upside down • Damaged disc • Water condensation on optics Radio Display Messages Your radio has been designed to display certain messages when a problem is detected with the CD player.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will bypass stations without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL 133 Bass and Treble Tone Control The tone controls consist of 2 separate bands. The bass band is on the left, and the treble band is on the right. Each band is adjusted by a slider control with a detent at the mid-position. Moving the control up or down increases or decreases amplification of that band. The mid position provides a flat frequency response. AM/FM Selection Press the AM/FM button to change from AM to FM.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Changes or modifications not expressively approved by the party responsible for compliance could void the user’s authority to operate the equipment. display will show the track number and index time in minutes and seconds. Play will begin at the start of track one. CD Player Operation Seek Press the top of the SEEK button for the next selection on the CD.
UNDERSTANDING YOUR INSTRUMENT PANEL 135 Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track. Press the RND (button 4) button a second time to stop Random Play.
UNDERSTANDING YOUR INSTRUMENT PANEL FF/RW — TUNE Press FF/TUNE/RW to skip through the tracks in the desired direction, until the button is released (it will not stop at the beginning/end of any track until you release the button). SALES CODE RB1—AM/FM STEREO RADIO WITH DVD/GPS NAVIGATION SYSTEM — IF EQUIPPED Disc/Program Button 5 Press the DISC (button 5) button to play the previous disc. Seek Press the top of the SEEK button for the next selection on the CD.
UNDERSTANDING YOUR INSTRUMENT PANEL 137 SATELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius™ Satellite Radio. This service offers up to 100 channels of music, sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios.
UNDERSTANDING YOUR INSTRUMENT PANEL Selecting Satellite Mode in RBB and RBK Radios Press the MODE button repeatedly until ⬙S A⬙ appears in the display. A CD or tape may remain in the radio while in the Satellite radio mode. Selecting Satellite Mode in RBP, RBU, RAZ, and RBQ Radios Press the MODE button repeatedly until the word ⬙SIRIUS⬙ appears in the display. These radios will also display the following: • After 3 seconds, the current channel name and channel number will be displayed for 5 seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 139 Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory. These satellite channel pre-set stations will not erase any AM or FM pre-set memory stations. Follow the memory pre-set procedures that apply to your radio. Using the PTY (Program Type) Button (if equipped) Follow the PTY button instructions that apply to your radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 6 DISC CD CHANGER — IF EQUIPPED The CD changer is located below the radio in the instrument panel. The changer plays only 4 3⁄4 inch (12 cm) discs. The changer holds up to 6 discs. Each disc is loaded and ejected through a single slot in front of the changer. Each disc has a numbered button with an amber light above it which, when illuminated, indicates that a disc is loaded in that particular chamber.
UNDERSTANDING YOUR INSTRUMENT PANEL 141 Seek Button Press the top of this button on the radio once to play the next track. Press the bottom of the button once to return to the beginning of the current track. Press the bottom of the button twice to play the previous track. FF/TUNE/RW Press the FF (fast forward) button and the CD player will fast forward through the tracks until the button is released.
UNDERSTANDING YOUR INSTRUMENT PANEL • Pressing the AM/FM button while in the tape or CD mode will select the radio mode. • If in the CD mode and the last CD is ejected, the radio will tune to the last station selected. REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches.
UNDERSTANDING YOUR INSTRUMENT PANEL 143 Pressing the center button will make the radio switch between the various modes available (AM/FM/TAPE/ CD, Etc.). The left hand control is a rocker type switch with a push-button in the center. The function of the left hand control is different depending on which mode you are in. The following describes the left hand control operation in each mode.
UNDERSTANDING YOUR INSTRUMENT PANEL If you press the switch up or down twice it plays the second track, three times, it will play the third, etc. The button in the center of the left hand switch will cause the CD changer to play the next available disc. CASSETTE TAPE AND PLAYER MAINTENANCE To keep the cassette tapes and player in good condition, take the following precautions: 1. Do not use cassette tapes longer than C-90; otherwise, sound quality and tape durability will be greatly diminished. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 145 COMPACT DISC MAINTENANCE To keep the compact discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6.
UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS Automatic Temperature Control (ATC) near the windshield glass. The In-Car Temperature Sensor is mounted behind the ATC control panel. These sensors transmit data on sun strength and vehicle interior temperatures to enhance system performance. CAUTION! Do not cover either sensor with any foreign material as improper operation of the system will result.
UNDERSTANDING YOUR INSTRUMENT PANEL 147 Fan Control Use this control to regulate the amount of air forced through the system in any mode you select. Turn the control clockwise to increase fan speed. In ambient temperatures below 70°F (21°C), fan operation is delayed when the engine is first started. The fan will automatically start when the engine coolant is warm enough to heat the air. This feature can be defeated by turning the fan control.
UNDERSTANDING YOUR INSTRUMENT PANEL engine speed or power may be noticed when the compressor is on. This is a normal occurrence since the compressor will cycle on and off to maintain comfort and improve fuel economy. Recirculate Button Press this button to recirculate the air inside the vehicle. Outside air is prevented from entering the vehicle. Recirculation is automatically controlled when the system is in Auto Mode. Use this mode to temporarily block out any outside odors, smoke, or dust.
UNDERSTANDING YOUR INSTRUMENT PANEL 149 NOTE: There is a varying difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature provides improved comfort during sunny but cool conditions. Windshield Defrost Air is directed through the defrost outlets and side window demist outlets. A small amount of air also is directed through the floor outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL Hot Weather Automatic Recirculation The system will automatically recirculate the air inside the vehicle when the interior is very warm. This will provide maximum cooling. The system will also occasionally return to REC on hot, humid days to maintain occupant comfort. See Operating Tips chart at the end of this section for suggested control settings in different weather conditions. Side Window Demisters Side window demisters are located on the instrument panel.
UNDERSTANDING YOUR INSTRUMENT PANEL 151 Operating Tips 4
UNDERSTANDING YOUR INSTRUMENT PANEL Outside Air Intake Make sure that the air intake directly in front of the windshield is free of obstructions. Leaves, snow, etc., could block air flow into the vehicle.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 155 䡵 Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 155 ▫ Autostick Operation . . . . . . . . . . . . . . . . . . . 159 ▫ Extremely Cold Weather (Below -20°F Or -29°C) . . . . . . . . . . . . . . . . . 155 ▫ Autostick General Information . . . . . . . . . . . . 160 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . .
STARTING AND OPERATING ▫ Radial-Ply Tires . . . . . . . . . . . . . . . . . . . . . . 168 ▫ 300M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 ▫ Spare Tire Usage With Directional Tread Pattern Tires (300M Special Only) . . . . . . . . . . . . . . . 169 ▫ 300M Special Only . . . . . . . . . . . . . . . . . . . . 175 ▫ Compact Spare Tire . . . . . . . . . . . . . . . . . . . . 169 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . . 170 ▫ Tire Chains . . . . . . . . . . .
STARTING AND OPERATING 155 STARTING PROCEDURES WARNING! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. The gear selector must be in the NEUTRAL or PARK position before you can start the engine. Apply the brakes before shifting to any driving gear. Normal Starting Normal Starting of either a cold or a warm engine does not require pumping or depressing the accelerator pedal.
STARTING AND OPERATING If Engine Fails To Start CAUTION! Do not try to push or tow your vehicle to get it started. Your vehicle cannot be started this way. Pushing with another vehicle may damage the transaxle or the rear of your vehicle. See Section 6 of this manual for the proper jump starting procedures. If the engine fails to start after following the Normal Starting procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine.
STARTING AND OPERATING 157 After Starting The idle speed will automatically decrease as the engine warms up. ENGINE BLOCK HEATER — Optional U.S. and Standard Canada These heaters use a common power cord which is stored under the hood, behind the Air Cleaner housing. Plug the cord into any 110 volt AC outlet and both heaters will be energized. Use the heaters when temperatures below 0°F (-18°C) are expected to last for several days.
STARTING AND OPERATING Transaxle Reset Mode The transaxle is monitored for abnormal conditions. If a condition is detected that could cause damage, the transaxle automatically shifts into second gear. The transaxle remains in second gear despite the forward gear selected. Park (P), Reverse (R), and Neutral (N) will continue to operate. This Reset feature allows the vehicle to be driven to a dealer for service without damaging the transaxle.
STARTING AND OPERATING 159 When frequent transaxle shifting occurs when using the Overdrive range, such as when operating the vehicle under heavy loading conditions (in hilly terrain, traveling into strong head winds, or while towing heavy trailers, use the AutoStick mode and select the “3” range. AUTOSTICK Autostick is a driver-interactive transmission that offers manual gear shifting capability to provide you with more control.
STARTING AND OPERATING Autostick General Information • The transmission will automatically upshift from first to second gear and from second to third gear when engine speed reaches about 6300 rpm. • Downshifts from third to second gear above 85 mph (137 km/h) and from second to first gear above 47 mph (76 km/h) will be ignored. • You can start out in first, second, or third gear. Shifting into fourth gear can occur only after vehicle speed reaches 17 mph (27 km/h).
STARTING AND OPERATING 161 PARKING BRAKE When the parking brake is applied with the ignition on, the red Brake light in the instrument cluster will come on. 5 NOTE: This light only shows that the parking brake is applied. It does not show the degree of brake application. Before leaving the vehicle, make sure that the parking brake is fully applied and place the gear selector in the Park position. To release the parking brake, pull the release lever located on the lower edge of the instrument panel.
STARTING AND OPERATING WARNING! • Leaving children in a vehicle unattended is dangerous for several reasons. A child or others could be injured. Children should be warned not to touch the parking brake or the gear selector. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle. • Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and an accident.
STARTING AND OPERATING 163 Anti-Lock Brake System (ABS) The ABS gives increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up. POWER STEERING Your vehicle is equipped with power assisted steering as standard equipment. The power assisted steering system of your vehicle provides mechanical steering capability in the event power assist is lost.
STARTING AND OPERATING • The system has been deactivated to prevent damage to the brake system due to overheated brake temperatures. NOTE: Extended heavy use of Traction Control may cause the system to deactivate and turn on the Traction Control OFF Light, indicated by TRAC OFF , located in the instrument cluster. This is to prevent overheating of the brake system and is a normal condition. After cooling, the system will automatically reactivate and turn off the TRAC OFF light.
STARTING AND OPERATING 165 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases tire rolling resistance and results in higher fuel consumption. Tire Inflation Pressures The proper tire pressure for your vehicle is listed on a label attached to the rear face of the driver’s door.
STARTING AND OPERATING period. The cold inflation pressure must not exceed the maximum values molded into the tire side wall. Tire pressure may increase from 2 to 6 psi [.13 to.41 bars] (13 to 40 kPa) during operation. Do NOT reduce this normal pressure build up or your tire pressure will be too low. The tire pressures shown on the tire label apply only to the tire sizes listed on the label.
STARTING AND OPERATING 167 CAUTION! The TPM system has been optimized for the original equipment tires and wheels. TPM system pressures have been established for the tire size equipped on your vehicle. Undesirable operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. After-market wheels can cause sensor damage. Do not use tire sealant or balance beads if your vehicle is equipped with TPM system as damage to the sensors may result.
STARTING AND OPERATING CAUTION! WARNING! After inspecting or adjusting the tire pressure always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the wheel rim sensor. High speed driving with your vehicle under load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
STARTING AND OPERATING 169 Spare Tire Usage with Directional Tread Pattern Tires (300M Special Only) The 300M Special model offers tires with a directional tread pattern. These tires are designed to optimize dry handling as well as wet performance. To obtain the full benefits of this design, the tires must be installed so that they rotate in the correct direction. The rotation direction of this type of tire is indicated by arrows on the side wall of the tire.
STARTING AND OPERATING Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph. (48 km/h). Tire Chains Due to limited clearance, tire chains are not recommended. See the paragraph on Freeing A Stuck Vehicle in section 6 of this manual. CAUTION! WARNING! Damage to the vehicle may result if tire chains are used. Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure.
STARTING AND OPERATING 171 WARNING! The 300M Special is equipped with tires that are optimized for driving in dry and wet weather conditions. However, these tires have reduced traction capability in snow and ice. When driving a 300M Special in these conditions with these tires, you must take special care to maintain control and avoid accidents. We recommend that you equip your vehicle with “SNOW” or “ALL SEASON” tires on all four wheels for driving in snowy and icy conditions.
STARTING AND OPERATING These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point. Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct inflation pressure.
STARTING AND OPERATING 173 CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. Check with your dealer before replacing tires with a different size. Tire Rotation Recommendations Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear patterns.
STARTING AND OPERATING of this type of tire is indicated by arrows on the side wall of the tire. The required rotation method for directional tires is to swap the front tire with the rear on the same side of the vehicle. Do not cross switch tires without dismounting the tires and re-mounting them in the correct rotational direction. Alignment And Balance The suspension components of your vehicle should be inspected and aligned when needed to obtain full tire tread mileage.
STARTING AND OPERATING 175 FUEL REQUIREMENTS 300M Your engine is designed to meet all emissions regulations and provide satisfactory fuel economy and performance when using high quality unleaded gasoline having an octane range of 87 to 89 or higher. The manufacturer recommends the use of 89 octane for optimum performance.
STARTING AND OPERATING Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with materials called oxygenates such as 10% ethanol, MTBE and ETBE. Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle. CAUTION! DO NOT use gasolines containing Methanol.
STARTING AND OPERATING 177 Materials Added to Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in unnecessary cost. Therefore, you should not have to add anything to the fuel. unleaded gasoline having lower sulfur to determine if the problem is fuel related prior to returning your vehicle to an authorized dealer for service.
STARTING AND OPERATING CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. The Malfunction Indicator light will come on if the gas cap is not properly secured. NOTE: The fuel tank filler tube has a restricting door about 2 inches (50 mm) down from the opening.
STARTING AND OPERATING 179 VEHICLE LOADING The load carrying capacity of your vehicle is shown in the following sample chart and on the tire pressure label attached to the driver’s door. Luggage Racks External racks do not increase the total load carrying capacity of the vehicle. Be sure the total occupant and luggage load inside the vehicle, plus that on the external rack, do not exceed the rated vehicle capacity shown on the Vehicle Loading Capacity chart.
STARTING AND OPERATING adequate performance. For Example, choose “4” if the desired speed can be maintained. Choose “3” or “2” if needed to maintain the desired speed. • Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are recommended for motoring safety. Extended driving at high RPM’s should be avoided to prevent excess heat generation. A reduction in vehicle speed may be necessary to avoid extended driving at high RPMs.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 182 䡵 Jump-Starting The Battery . . . . . . . . . . . . . . . 189 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 182 䡵 Driving On Slippery Surfaces . . . . . . . . . . . . . 191 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 183 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . . 191 ▫ Preparations For Jacking . . . . . . . . . . . . . . . . 184 ▫ Traction . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is on the steering column, just behind the steering wheel. Push in the flasher switch and all front and rear directional signals will flash. Press the flasher switch a second time to turn the flashers off. If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and the vehicle locked. NOTE: With extended use, the flasher may run down your battery.
WHAT TO DO IN EMERGENCIES 183 the fan control to High. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, turn the engine off immediately, and call for service.
WHAT TO DO IN EMERGENCIES Preparations For Jacking • Turn on the Hazard Warning Flashers and park the vehicle on a firm level surface, avoiding ice or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. Jacking and Changing a Tire 1. Block the wheel diagonally opposite the flat tire.
WHAT TO DO IN EMERGENCIES 185 3. Before raising the vehicle, use the lug wrench to loosen the lug nuts of the flat tire. 4. Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange, use the lift area closest to the flat tire.
WHAT TO DO IN EMERGENCIES 5. Raise the vehicle just enough to remove the flat tire and install the spare tire. 6. Remove the lug nuts, wheel cover (if equipped) and tire. Remove the cover by hand, do not pry off.
WHAT TO DO IN EMERGENCIES 187 WARNING! WARNING! Death or serious injury can occur if magnetically sensitive devices are exposed to this magnet. Magnets can affect pacemakers. Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 7. Mount the spare tire. For vehicles equipped with wheel covers, see the wheel cover installation instructions.
WHAT TO DO IN EMERGENCIES Compact Spare Tire-For Temporary Emergency Use Only • Keep tire inflated to 60 PSI (414 KPa) Cold Inflation Pressure. • Avoid driving more than 50 miles (80 km) before replacing tire and wheel. • This tire is designed as an emergency spare only-do not exceed 50 MPH (80 km/h) speed. Wheel Cover Installation (If Required) 1. Tighten the two lug nuts on the mounting studs on each side of the stud which is in alignment with the valve stem. 2.
WHAT TO DO IN EMERGENCIES 189 JUMP-STARTING THE BATTERY WARNING! Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be hurt by the fan. CAUTION! Do not try to push or tow your vehicle to get it started. Your vehicle cannot be started this way. Pushing with another vehicle may damage the transaxle or the rear of your vehicle.
WHAT TO DO IN EMERGENCIES Remote jump starting terminals are located in the engine compartment. Check the Battery Test Indicator. If a light or bright colored dot is visible in the indicator, DO NOT jump-start the battery. If the indicator is dark or shows a green dot, proceed as follows: 1. Wear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. 2.
WHAT TO DO IN EMERGENCIES 191 5. Connect the other cable, first to the negative jump start attachment of the booster battery and then to the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. 6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 7. When removing the jumper cables, reverse the above sequence exactly.
WHAT TO DO IN EMERGENCIES WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have an accident. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet, mud, loose sand, etc.). Traction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface.
WHAT TO DO IN EMERGENCIES 193 CAUTION! CAUTION! Racing the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h). • Do not attempt to tow this vehicle from the front with sling type towing equipment. Damage to the front fascia will result. • Always use wheel lift equipment when towing from the front. The only other approved method of towing is with a flat bed truck.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 3.5L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 197 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . . 213 䡵 Onboard Diagnostic System (OBD II) . . . . . . . 198 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . . 213 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . . . 214 䡵 Replacement Parts . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 䡵 Replacement Light Bulbs . . . . . . . . . . . . . . . . 230 ▫ License Plate Light . . . . . . . . . . . . . . . . . . . . 235 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 230 䡵 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 235 ▫ Headlight And Parking Light Removal . . . . . . 230 䡵 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . 236 ▫ Front Park, Turn Signal And Front Sidemarker Light . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 197 3.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) To meet new government regulations and promote cleaner air, your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transaxle control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 199 EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing.
MAINTAINING YOUR VEHICLE If your OBD system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update. A recheck with the above test routine may then indicate that the system is now ready.
MAINTAINING YOUR VEHICLE 201 WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. MAINTENANCE PROCEDURES The pages that follow contain the maintenance service recommended by the engineers who designed your vehicle.
MAINTAINING YOUR VEHICLE The best time to check the oil level is about 5 minutes after a fully warmed up engine is shut off or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground also will improve the accuracy of the oil level readings. Maintain the oil level between the MIN and MAX markings on the dipstick. Adding one quart of oil when the reading is at the MIN mark will result in a MAX reading on these engines.
MAINTAINING YOUR VEHICLE 203 • More than 50% of your driving is at sustained high speeds during hot weather above 90°F (32°C) • Trailer towing • Taxi, police or delivery service (commercial service) • Off road or desert operation • If equipped for and operating with E —85 (ethanol) fuel NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual.
MAINTAINING YOUR VEHICLE American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). We only recommend API Certified engine oils that meet the requirements of DaimlerChrysler’s Material Standard MS-6395. Use Mopar or an equivalent oil meeting the specification MS-6395. NOTE: SAE 10W-30 engine oil is preferred for use in 3.5L Engines within the operating temperatures shown in the viscosity chart.
MAINTAINING YOUR VEHICLE 205 performance may be impaired by supplemental additives. Disposing of Used Engine Oil Care should be taken in disposing of used engine oil from your vehicle. Used oil, indiscriminately discarded, can present a problem to the environment. Contact your dealer, service station, or governmental agency for advice on how and where used oil can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced at every engine oil change.
MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Under normal driving conditions, replace the air filter at the intervals shown on Schedule “A”. If, however, you drive the vehicle frequently under dusty or severe conditions, the filter element should be inspected periodically and replaced if necessary at the intervals shown on Schedule “B”. WARNING! The air cleaner can provide a measure of protection in the case of engine backfire.
MAINTAINING YOUR VEHICLE 207 CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle.
MAINTAINING YOUR VEHICLE replace it with a new valve. DO NOT ATTEMPT TO CLEAN THE OLD PCV VALVE! WARNING! Check ventilation hose for indication of damage or plugging deposits. Replace if necessary. Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water.
MAINTAINING YOUR VEHICLE 209 CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion. Apply grease to posts and clamps after tightening.
MAINTAINING YOUR VEHICLE Power Steering Fluid Check WARNING! Fluid level should be checked with the engine off to prevent injury from moving parts. Do not overfill. Use only the manufacturer’s recommended power steering fluid. Refer to Recommended Fluids, Lubricants and Genuine Parts for the correct fluid type. During scheduled maintenance, check the power steering fluid level at the power steering fluid reservoir.
MAINTAINING YOUR VEHICLE 211 Drive Shaft Universal Joints Your vehicle has four constant velocity universal joints. Periodic lubrication of these joints is not required. However, the joint boots should be inspected for external leakage or damage when other maintenance is performed. If leakage or damage is evident, replace the universal joint boot and grease immediately. Continued operation could result in failure of the universal joint due to water and dirt contamination of the grease.
MAINTAINING YOUR VEHICLE then proceed as described above, to distribute the lubricant within the lock cylinder. Pay attention to trunk hinges, especially during cold weather, to ensure ease of trunk operation.
MAINTAINING YOUR VEHICLE 213 Windshield Washers The fluid reservoir in the engine compartment should be checked for fluid level at regular intervals. Fill the reservoir with windshield antifreeze (not radiator antifreeze) rated not to freeze at -25°F (-31°C). Operate the system for a few seconds to flush out the residual water. WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution.
MAINTAINING YOUR VEHICLE WARNING! Exhaust gases can injure or kill. They contain carbon monoxide which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. Follow the above precautions to keep your exhaust system as safe as possible. Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition key to the OFF position. The fan is controlled by engine coolant temperature and Air Conditioning pressure.
MAINTAINING YOUR VEHICLE 215 Check the front of the radiator and condenser for any accumulation of bugs, leaves, etc. Clean the radiator and condenser by gently spraying water from a garden hose at the back of the core. coolant in open containers or allow it to remain in puddles on the ground. Prevent ingestion by animals or children. If ingested by a child, contact a physician immediately. Check the engine cooling system hoses for condition and tightness of connection.
MAINTAINING YOUR VEHICLE Higher concentrations (not to exceed 70%) may be used if temperatures below -37°F (-38°C) are anticipated. WARNING! Use only high purity water such as distilled or deionized water when mixing the water/antifreeze solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add coolant when the engine is overheated.
MAINTAINING YOUR VEHICLE 217 Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine Off and cold, the level of the coolant in the bottle should be between the MIN and MAX cold fill lines. Points to Remember NOTE: When the vehicle is stopped after a few miles of operation, you may observe vapor coming from the front of the engine compartment.
MAINTAINING YOUR VEHICLE • Maintain a coolant concentration of a minimum of 50% ethylene glycol and high quality water with recommended antifreeze for proper corrosion protection of your engine cooling system that contains aluminum components. Pay particular attention to those hoses nearest to high heat sources such as the exhaust manifold. Inspect hose routing to be sure hoses do not touch any heat source or moving component that may cause heat damage or mechanical wear.
MAINTAINING YOUR VEHICLE 219 WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency. Brake and Power Steering System Hoses When servicing the vehicle for scheduled maintenance, inspect surface of hoses for evidence of heat and mechanical damage.
MAINTAINING YOUR VEHICLE Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear. However, low fluid level may be caused by a leak and a checkup may be needed.
MAINTAINING YOUR VEHICLE 221 Automatic Transaxle All front wheel drive vehicles have a transaxle and differential assembly contained within a single housing. Selection of Lubricant It is important that the proper lubricant is used in the transaxle to assure optimum transaxle performance. Use only the manufacturer’s recommended transmission fluid. Refer to the Recommended Fluids, Lubricants and Genuine Parts section for correct fluid type.
MAINTAINING YOUR VEHICLE Fluid Level Check The fluid level in the automatic transaxle should be checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly reduce the life of the transaxle and of the fluid. • The engine should be running at curb idle speed for a minimum of 60 seconds. • Fully apply parking brake. • Place the gear selector momentarily in each gear position ending with the lever in P (PARK). • Wipe the dipstick clean and reinsert until seated.
MAINTAINING YOUR VEHICLE 223 CAUTION! If the transaxle is disassembled for any reason, the fluid and filter should be changed. Do not overfill. Dirt and water in the transaxle can cause serious damage. To prevent dirt and water from entering the transaxle after checking or replenishing fluid, make certain that the dipstick cap is seated properly. Special Additives The manufacturer recommends against the addition of any fluid additives to the transaxle.
MAINTAINING YOUR VEHICLE The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • Road salt, dirt and moisture accumulation. • If insects, tar or other similar deposits have accumulated on your vehicle, wash it as soon as possible.
MAINTAINING YOUR VEHICLE 225 • It is important that the drain holes in the lower edges of the doors, rocker panels and rear deck lid be kept clear and open. • If you carry special cargo such as chemicals, fertilizers, deicer salt, etc., be sure that such materials are well packaged and sealed. • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner.
MAINTAINING YOUR VEHICLE CAUTION! The use of vinyl, leather or plastic protectants may cause excessive gloss and/or discoloration of interior trim parts. Leather Seat Care and Cleaning Leather is best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather surface and should be removed immediately with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar Total Clean.
MAINTAINING YOUR VEHICLE 227 protectants or other products which may cause undesirable reflections. Use soap and warm water to restore the low glare surface. Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. FUSES The fuse block is behind the end cover at the left side of the instrument panel.
MAINTAINING YOUR VEHICLE Underhood Fuses A Power Distribution center is located in the engine compartment. This center contains fuses and relays for circuits that operate only under the hood. A label which identifies these components is located on the underside of the cover. CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
MAINTAINING YOUR VEHICLE 229 Cavity 7 8 9 10 11 12 13 14 15 16 Fuse 20 Amp Yellow 10 Amp Red 10 Amp Red 15 Amp Lt. Blue 20 Amp Yellow 15 Amp Lt.
MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS Interior Light Bulbs Turn Signal . . . . . . . . . . Climate Control. . . . . . . Overhead Console, Front Handle . . . . . . . . . . . . . Trunk . . . . . . . . . . . . . . Bulb No. . . . . . . . . . . . . . . . . . PC194 . . . . . . . . . . . . . . . . . . . 330 Reading, Courtesy, Grab . . . . . . . . . . . . . . . . . . . 192 . . . . . . . . . . . . . . . . . . . 906 Exterior Light Bulbs Bulb No. Low Beam Headlights . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 231 2. Remove the upper crossmember attachments on both sides of the vehicle; 6 in total. 3. Remove the headlamp jackscrews on both sides of the vehicle.
MAINTAINING YOUR VEHICLE 4. Remove the windshield filler neck screw. 5. Remove the speed control servo screw.
MAINTAINING YOUR VEHICLE 233 6. Lift and prop the crossmember above the headlamp on the side being serviced, and remove the electrical connectors from the headlamp. 11. Reinstall the upper crossmember attachments, headlamp jackscrews, windshield filler neck screw and speed control servo screw. 7. Pull headlamp up and under crossmember to remove it from the vehicle. Front Park, Turn Signal and Front Sidemarker Light 8. Remove the bulb retaining ring by turning it counterclockwise.
MAINTAINING YOUR VEHICLE Center Stop Light Tail, Stop, Back Up, and Turn Signal Lights 1. Open the trunk and remove the trunk lid cover. 2. Turn the bulb socket counterclockwise and remove it from the housing. 3. Pull the bulb from the socket and replace the bulb. 4. Reinstall the bulb and socket assembly. 1. Open the trunk and remove the fasteners securing the light housing to the body. 2. Pull the light housing from the body to expose the wiring socket. 3.
MAINTAINING YOUR VEHICLE 235 License Plate Light 1. Remove the screws securing the light to the rear fascia. 2. Remove the bulb and socket assembly and pull the bulb from the socket. 3. Replace the bulb and reinstall the bulb and socket assembly. 4. Reattach the light to the rear fascia. SPECIFICATIONS ENGINE Oil Filter Thermostat Spark Plug Spark Plug Gap Firing Order 3.
MAINTAINING YOUR VEHICLE FLUID CAPACITIES Fuel (Approximate) Engine Oil with Filter 3.5 Liter Engine U.S. 17 Gallons Metric 64 Liters 5 Qts 4.7 Liters 11 Qts 10.5 Liters Cooling System * 3.5 Liter Engine * Includes heater and coolant recovery bottle filled to MAX level.
MAINTAINING YOUR VEHICLE 237 RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Spark Plugs Oil Filter Fuel Selection Fluid, Lubricant or Genuine Part Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) Use API Certified (GF-3). Refer to oil viscosity chart for correct SAE grade. Refer to the Vehicle Emission Control Information label in the engine compartment.
MAINTAINING YOUR VEHICLE Body Component Hinges: Door, Hood and Trunk Hood hinge springs and links Latches: Door and Hood Trunk Door check straps Window System Components Lock Cylinders Parking Brake Mechanism Fluid, Lubricant or Genuine Part Mopar 威 Engine Oil Mopar 威 Spray White Lube Mopar威 Multi-Purpose Lube NLGI Grade 2 Mopar 威 Spray White Lube Mopar威 Spray White Lube Mopar威 Spray White Lube Mopar 威 Spray White Lube Mopar威 Spray White Lube
䡵 Emission Control System Maintenance . . . . . . 240 M A I N T E N A N C ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 243 E 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . 240 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 240 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 241 M NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual. NOTE: Most vehicles are operated under the conditions listed for Schedule ⬙B⬙. Second is Schedule “A”. It is for vehicles that are not operated under any of the conditions listed under Schedule ⬙B⬙. Use the schedule that best describes your driving conditions.
M A I N T E N A N C E S C H E D U L E S 8 242 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check tire pressure and look for unusual wear or damage. • Change the engine oil filter. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of coolant reservoir, brake master cylinder, power steering and transaxle and add as needed. • Check all lights and all other electrical items for correct operation.
SCHEDULE “B” SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an 〫. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16.2 km).
M 244 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Inspect the air cleaner filter and replace if reN C quired.* E Replace the air cleaner filter. * S C H E D U L E S 8 Inspect the front and rear brake linings and rotors. Adjust the drive belt tension.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Adjust the drive belt tension. Check and replace, if necessary, the PCV valve.
M 246 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Inspect the air cleaner filter and replace if reN C quired.* E Replace the air cleaner filter. * S C H E D U L E S 8 Adjust the drive belt tension. Inspect the front and rear brake linings and rotors. Replace the differential fluid.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Replace the drive belts. Replace the power steering fluid. Check and replace, if necessary, the PCV valve. * ‡ Change the automatic transaxle fluid and filter.
M 248 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Inspect the air cleaner filter and replace if reN C quired.* E Replace the air cleaner filter. * S C H E D U L E S 8 Replace the air cleaner filter. Adjust the drive belt tension. Inspect the front and rear brake linings and rotors. Check and replace, if necessary, the PCV valve.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Flush and replace the engine coolant. Replace the engine timing belt (Federal Emissions). Replace the engine timing belt (California Emissions). Replace the spark plugs. Adjust the drive belt tension. Change the differential fluid.
M 250 SCHEDULE “A” A I SCHEDULE “A” N T Miles E N (Kilometers) A [Months] N C Change engine oil and engine oil filter. E Inspect the air cleaner filter and replace if reS C H E D U L E S 8 quired.* Replace the air cleaner filter. * Adjust the drive belt tension. Inspect the front and rear brake linings and rotors. Inspect and replace PCV valve if required.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. * Replace the drive belts. Inspect the front and rear brake linings and rotors. Flush and replace engine coolant at 60 months or 100,000 miles. Check and replace, if necessary, the PCV valve.
M 252 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Inspect the air cleaner filter and replace if reE quired.* S C H E D U L E S 8 78,000 (125 000) [78] X X Replace the air cleaner filter. * Adjust the drive belt tension. Inspect the front and rear brake linings and rotors. Replace the spark plugs. Check and replace, if necessary, the PCV valve. *‡ Replace the engine timing belt (Federal Emissions equipped vehicles only).
SCHEDULE “A” WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 ▫ Prepare For The Appointment . . . . . . . . . . . . 256 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 256 䡵 Reporting Safety Defects . . . . . . . . . . . . . . . . . 259 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 259 䡵 Publication Order Forms . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE to make these arrangements when you call for an appointment. Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE 257 This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center.
IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unexpected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands behind only the manufacturer’s Service Contracts. If you purchased a manufacturer’s Service Contract, you will receive Plan Provisions and an Owner Identification Card in the mail within three weeks of your vehicle delivery date.
IF YOU NEED CONSUMER ASSISTANCE 259 MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
PUBLICATION ORDER FORMS 9
IF YOU NEED CONSUMER ASSISTANCE 263 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car.
IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . 162,163 ABS (Anti-Lock Brake) System . . . . . . . . . . . . . 116 Accident Damage . . . . . . . . . . . . . . . . . . . . . . . 225 Adding Engine Coolant (Antifreeze) . . . . . . . . . 215 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 177 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . 146 Air Conditioning Controls . . . . . . . . . . . . . . . . 146 Air Conditioning, Operating Tips . . . . . . . . . . .
INDEX 267 Saving Feature . . . . . . . . . . . . . . . . . . . . 64,65,67 Belts, Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 Belts, Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 207 Body Mechanism Lubrication . . . . . . . . . . . . . . 211 Brake, Parking . . . . . . . . . . . . . . . . . . . . . . . . . 161 Brake System . . . . . . . . . . . . . . . . . . . . . . . 162,218 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 Fluid Check . . . . . . . . . . .
INDEX Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . 226 Instrument Panel . . . . . . . . . . . . . . . . . . . . . 226 Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 Vinyl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 Waxing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Windshield Wiper Blades .
INDEX 269 Disabled Vehicle Towing . . . . . . . . . . . . . . . . . 193 Disposal Antifreeze . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 205 Door Ajar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Door Ajar Light . . . . . . . . . . . . . . . . . . . . . . . . 114 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . 14,15 Door Locks, Automatic . . . . . . . . . . . . . . . . . . . 16 Door Locks, Central .
INDEX Engine Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 206 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 205 Flashers Hazard Warning . . . . . . . . . . . . . . . . . . . . . . 182 Flat Tire Changing . . . . . . . . . . . . . . . . . . . . . . 183 Floor Shift Interlock . . . . . . . . . . . . . . . . . . . . . . 13 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . 236 Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Fog Lights . . . . .
INDEX 271 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 High Beam Indicator . . . . . . . . . . . . . . . . . . . . 114 Holder, Coin . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Holder, Cup . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Holder, Pencil . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Homelink Transmitter . . . . . . . . . . . . . . . . . . 75,80 Hood Release . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Hook, Coat . . . . . . .
INDEX Cruise . . . . . . . . . . . . . . . . . . . . . . . . . . . 72,114 Daytime Running . . . . . . . . . . . . . . . . . . . . . . 68 Dimmer Switch, Headlight . . . . . . . . . . . . . . . 68 Dome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Door Ajar . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Exterior Check . . . . . . . . . . . . . . . . . . . . . . . . 48 Fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67,233 Front Replacement . . . . . . . . . . .
INDEX 273 Malfunction Indicator Light . . . . . . . . . . . . 115,199 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . 261 Memory Feature . . . . . . . . . . . . . . . . . . . . . . . . 60 Memory Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Mini-Trip Computer . . . . . . . . . . . . . . . . . . . . . . 98 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Automatic Dimming . . . . . . . . . . . . . . . . . . . . 54 Electric Remote . . . . . . . . . . .
INDEX Pets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Pets, Transporting . . . . . . . . . . . . . . . . . . . . . . . 46 Power Distribution Center . . . . . . . . . . . . . . . . . . . . 228 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 275 Seat Belt Maintenance . . . . . . . . . . . . . . . . . . . 227 Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . 27,28,48 Adjustable Upper Shoulder Anchorage . . . . . . 32 Child Restraint . . . . . . . . . . . . . . . . . . . . . . . . 45 Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Seats . . . . . . . . . . . . . . . . . . . .
INDEX Synthetic Engine Oil . . . . . . . . . . . . . . . . . . . . . 204 System, Navigation . . . . . . . . . . . . . . . . . . . . . 136 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Tape Player . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 Temperature Gauge, Engine Coolant . . . . . . 114,183 Theft Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Theft System . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Tilt Steering Column . . . . . . .
INDEX 277 Transmitter, Garage Door Opener . . . . . . . . . . 75,80 Transmitter Programming . . . . . . . . . . . . . . . . . 20 Transporting Pets . . . . . . . . . . . . . . . . . . . . . . . . 46 Traveler Trip Computer . . . . . . . . . . . . . . . . . . . 98 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . 171 Trip Computer . . . . . . . . . . . . . . . . . . . . . . . 98,102 Trip Odometer . . . . . . . . . . . . . . . . . . . . . . 103,115 Trip Odometer Reset Button . . . . . . . . . . . . .
