TABLE OF CONTENTS SECTION PAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1 1 INTRODUCTION 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4 UNDERSTANDING YOUR INSTRUMENT PANEL 5 STARTING AND OPERATING 6 WHAT TO DO IN EMERGENCIES 7 MAINTAINING YOUR VEHICLE 8 MAINTENANCE SCHEDULES 9 IF YOU NEED CONSUMER ASSISTANCE 10 INDEX . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS m Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m Warnings And Cautions . . . . . . . . . . . . . . . . . . 6 m How To Use This Manual . . . . . . . . . . . . . . . . . 4 m Vehicle Identification Number . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your Crossfire. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . . 9 ▫ Emergency Unlocking Feature . . . . . . . . . . . . .13 ▫ Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 ▫ Start Lockout . . . . . . . . . . . . . . . . . . . . . . . . .13 ▫ Obtaining Replacement Keys . . . . . . . . . . . . . . 9 m Remote Keyless Entry . . . . . . . . . . . . . . . . . . . .14 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE m Power Windows . . . . . . . . . . . . . . . . . . . . . . . .18 m Engine Break-In Recommendations . . . . . . . . . .43 m Rear Liftgate Release . . . . . . . . . . . . . . . . . . . .19 m Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 m Occupant Restraints . . . . . . . . . . . . . . . . . . . . .20 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . .44 ▫ Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS You can insert the double-sided keys into the locks with either side up. 9 The transmitter for the remote control is located in the key fob. 2 The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys only from an authorized dealer. Ask your dealer for these numbers and keep them in a safe place. CAUTION! An unlocked car is an invitation to thieves.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Turning the key in the steering lock to the ON/RUN position deactivates the start lock-out. key cylinder. If this occurs, turn the key clockwise slightly, then remove the key as described. NOTE: In case the engine cannot be started, and START and ERROR are shown in the odometer display field, the system is not operational. Contact an authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To unlock the glove compartment, turn the key to the horizontal or left position, and then remove the key. DOOR LOCKS The vehicle doors can be locked when the doors are closed by either manually pressing the button down at the top of the door panel, pressing and releasing the bottom portion of the central locking switch located in the console, or by pressing and releasing the Lock transmit button on the key fob.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: In case of a malfunction in the central locking system, the doors can be locked and unlocked individually. To lock, turn the key in the driver’s door lock clockwise, or push down the lock buttons. To unlock, turn the key in the driver’s door lock counterclockwise, or pull the inside door handles. WARNING! For personal security and safety in the event of an accident, lock the vehicle doors as you drive and when you park and leave the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE locking feature and neither door is opened, the doors remain unlocked even at vehicle speeds of approximately 9 mph (15 km/h) or more. NOTE: If you attempt to lock the doors with the key in the ignition and the driver’s door open, the doors will not lock. General Notes On the Central Locking System If the key in the ignition switch is in the ON/RUN position, the vehicle cannot be locked or unlocked with the remote control.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY This feature allows you to lock or unlock the vehicle from remote locations using a hand-held transmitter located in the key fob. You don’t have to point the transmitter at the vehicle to activate the system. The vehicle doors, rear liftgate, and fuel filler door can be locked and unlocked using the remote control. To Unlock the Doors: Press and release the unlock button on the key fob.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the vehicle cannot be locked or unlocked by pressing the transmit button, then it may be necessary to change the batteries in the remote control. Panic Alarm The panic alarm unlocks the driver’s door, turns on the interior lights, flashes the foglights and sounds the horn for about three minutes or until the alarm is turned off. The vehicle can be driven while in the Panic mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. This device must accept any interference that may be received, including interference that may cause undesired operation. • Remove the old batteries. Transmitter Battery Service The recommended replacement Lithium battery is Panasonict CR 2025 or equivalent. To change the batteries: • Insert the new batteries in the direction of the arrow with the positive symbol facing upwards. • Replace the battery cover and press on it until you feel it engage.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE approximately 30 seconds, insert the key in the ignition and turn it to the ON/RUN position. The remote control should once again be operational. SECURITY ALARM SYSTEM The system monitors the doors, rear liftgate, hood, and ignition for unauthorized operation. The security alarm system is automatically armed or disarmed with the remote control or any of your vehicle’s keys by locking or unlocking the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The tow-away alarm remains switched off until the vehicle is locked again with the key or the remote control, at which time it is automatically reactivated. POWER WINDOWS The power window switches are located in the console. To operate, turn the key in the ignition switch to the ACC or ON/RUN position. Press the switch in to the resistance point to open; release the switch when the window is in the desired position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When closing the windows, be sure that there is no danger of anyone being harmed by the closing procedure. 19 REAR LIFTGATE RELEASE You can open the rear liftgate by using the handle located on the liftgate just above the rear license plate pocket. WARNING! Do not allow children to have access to the rear cargo area by climbing into the rear cargo area from outside, or through the inside of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the lap/ shoulder seat belts for the driver and passenger, emergency tensioning retractors for the seat belts, and front and side airbags for the driver and passenger. If you will be carrying children too small for adult-size belts, the passenger side seat belt also can be used to hold infant and child restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belts Each seating position is equipped with a combined lap/shoulder belt system. The belt webbing retractor will lock only during very sudden stops or impacts. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But, in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out. The seat belts are also equipped with emergency tensioning retractors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap. 2 5. To loosen the lap belt if it is too tight, tilt the latch plate away from you and pull on the lap belt. Remember that a snug belt reduces the risk of sliding under the belt in a collision. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Restraint System (SRS) - Airbag The vehicle is also equipped with side airbags, located in the driver and passenger doors. Side airbags also work with seat belts to improve occupant protection. WARNING! This vehicle has airbags for the driver and passenger as a supplement to the seat belt restraint systems. The driver’s airbag is mounted in the steering wheel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The seat belts are designed to protect you in many types of collisions. The front airbags deploy only in moderate to severe front collisions. In certain types of collisions, both the front and side airbags may be triggered. But even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during airbag deployment could cause serious injury. • Airbags need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE These include all of the items listed above except the knee bolster, the instrument panel, and the steering wheel and column. • The Occupant Restraint Controller also turns on the AIRBAG light in the instrument panel for four seconds when the ignition is first turned on, then turns the light off. If it detects a malfunction in any part of the system, it turns on the light either momentarily or continuously depending on the condition that is present at the time.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The knee impact bolster helps protect the knees and working with the seat belts, position you for the best interaction with the airbags. The airbag system is designed to deploy when the impact sensors detect a moderate-to-severe frontal collision, to help restrain the driver and passenger, and then to immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE process that generates the nontoxic nitrogen gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers are designed to open only when the airbags are inflated. • Do not attach cup holders or any other objects on or around the door. The inflating side airbag could drive the objects into occupants, causing serious injury.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • The door mounted side airbag deploys with considerable force. Being too close to the door panel during airbag deployment could cause serious injury or death. • All occupants must be in the appropriate restraint for their size and age, especially children 12 and under. • To help avoid the potential for serious injury and death should the side airbag be activated, please follow these guidelines: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the airbag is turned off when there is any other occupant at that position, the supplemental restraint provided by the airbag will not be available. To Shut Off the Passenger Airbag: To turn OFF the passenger front airbag, use the on/off switch located on the instrument panel. NOTE: When the passenger airbag is turned off, the yellow airbag off light will illuminate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The switch does NOT turn off the side airbag. 35 To Turn On the Passenger Airbag: • Place the ignition key in the on/off switch, turn the key counterclockwise, and remove the key from the switch. This will turn on the passenger airbag. The Passenger Airbag Off light on the console will turn off, or will not be illuminated when the ignition is turned to the ON position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbag is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the airbag covers. Do not modify the front bumper or vehicle body structure. • You need proper knee impact protection in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A rearward facing infant restraint must not be used unless the passenger airbag has been shut off. A rearward facing infant restraint may be struck by a deploying passenger airbag which may cause severe or fatal injury to the infant. • Improper installation can lead to failure of a child restraint. It could come loose in a collision. The child could be badly injured or killed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system. (See LATCH - Child Seat Anchorage System section.) The belt-positioning booster seat is for children weighing more than 40 lbs. (18 kg), but who are still too small to fit the vehicle’s seat belts properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE are general instructions, and not all child restraint systems will be installed exactly as described here. Again, carefully follow the installation instructions that were provided with the child restraint system. The passenger seat tether anchorage is located on the back of the seat cushion frame. It is visible by moving the passenger seat forward in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap. You will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchorages. Next, you can attach the tether strap to the anchor by moving the passenger seat forward.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE retractor action is restored. Any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary. If your child restraint is equipped with a tether strap, attach it to the vehicle by first moving the seat back fully forward. Next, route the child restraint tether directly over the top of the seat, through the strap near the top of the seat back, and attach the hook to the anchor bar.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a child restraint top tether strap. Transporting Pets Deploying airbags could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the heating or cooling system to force outside air into the vehicle. Set the blower at high speed. SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defrosters Check operation by pressing the A/C control button, selecting the defrost mode and placing the blower control on high speed. You should be able to feel the air directed against the windshield. Periodic Safety Checks You Should Make Outside the Vehicle Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect for tread cuts or sidewall cracks.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 m Console Features . . . . . . . . . . . . . . . . . . . . . . .49 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .55 ▫ Storage Compartments . . . . . . . . . . . . . . . . . .49 ▫ Power Remote Control Outside Mirrors . . . . . .56 ▫ Ashtray . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 ▫ Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . .57 ▫ Coin Holder . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Instrument Panel Lighting . . . . . . . . . . . . . . . .61 m Brake Assist System (BAS) . . . . . . . . . . . . . . . .73 ▫ Night Security Illumination . . . . . . . . . . . . . . .61 m Electronic Stability Program (ESP) . . . . . . . . . . .74 m Exterior Lights . . . . . . . . . . . . . . . . . . . . . . . . .62 ▫ Synchronizing ESP . . . . . . . . . . . . . . . . . . . . .76 ▫ Headlights And Parking Lights . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES The console has a power outlet/cigar lighter, an ash tray with a coin holder, a cupholder, and the passenger airbag light. In addition, there are switches to control the heated seats, rear spoiler, electronic stability program (ESP), hazard flashers, central locking, rear defroster and towing alarm.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE A cargo net for storage is located in the footwell area on the passenger side. Additionally, storage pockets are located on the wall behind each seat and on each door panel. A storage pouch is located on the rear wall between the seats, and the driver’s sunvisor has a document strap. WARNING! Keep compartment lids closed. This will help to prevent stored objects from being thrown about and injuring vehicle occupants during an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 51 Ashtray Lightly touch the bottom of the ashtray cover. The ashtray will open automatically. To remove the ashtray insert, pull the ashtray past the detent. Hold both sides of the insert, and pull up. To install the ashtray, place it in the frame and push down to engage. WARNING! Remove the ashtray only with the vehicle stopped and the ignition off. Otherwise, the vehicle might move unexpectedly as a result of unintended contact with the gear selector lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Coin Holder With the ashtray open, folding down the cover plate reveals the coin holder, which can accommodate nine coins in various sizes up to a U.S. quarter. The coin slots are shaped to retain the coins, and the cover plate ensures that the coins remain in the coin holder. Power Outlet/Cigar Lighter The dual-purpose power outlet is located in the console, next to the passenger airbag off warning light.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 53 Glove Compartment To lock the glove compartment, turn the key to the right and remove. To unlock, turn the key to the left and remove. Pull on the handle to open the glove compartment. 3 CUPHOLDER The cupholder is located in the console. To open the cupholder, gently press downward on the front edge of the top panel, and then release. The cupholder will open automatically.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Adjusting The Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. Automatic Dimming Mirror Feature When the ignition switch is in the ON or RUN position, the automatic antiglare feature is activated. This feature automatically responds to changes in light sensitivity, and adjusts mirror brightness accordingly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Exterior Mirrors Folding Feature All exterior mirrors are hinged to move forward or rearward to resist damage. The hinges have three detent positions: full forward, full rearward, and normal. Heated Remote Control Mirrors Both outside mirrors are heated to melt frost or ice when the Rear Window Defroster switch is depressed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Remote Control Outside Mirrors The mirrors can be adjusted by using the remote control located in the console. Rotate the switch to the right to select the right mirror, rotate to the left to select the left mirror. Then use the switch to adjust the selected mirror to the desired direction.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vanity Mirrors 57 SEATS Driver Eight-Way Power Seat The switches to adjust the power seats are located on the outboard side of each seat. The driver’s seat features eight-way power adjustment - horizontal, vertical, cushion tilt and back angle. A vanity mirror is on each sun visor. To use the mirror, rotate the sun visor down and slide open the mirror cover.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Passenger Four-Way Power Seat The switches to adjust the passenger seat are also on the outboard side of the seat. The passenger seat provides four-way adjustment - horizontal and back angle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats This feature heats the driver and passenger seats. The controls for the heated seats are located on the instrument panel, below the radio. 59 TO OPEN AND CLOSE THE HOOD To open the hood, pull the release lever located inside your vehicle, below the instrument panel. 3 After turning the ignition switch ON, you can choose the HI, LO, or OFF setting. Indicators on the switches show which setting has been selected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To prevent possible damage, close the hood by dropping it from approximately 12 inches (30 cm). WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving, and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. INTERIOR LIGHTS A two-position mode selector switch controls the interior lights located in the overhead console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Map/Reading Lights These lights are located between the sun visors. A single centrally located switch operates both lights. 61 Instrument Panel Lighting With the parking lights or headlights on, rotate the dimmer control to the left of the speedometer to increase or decrease brightness of the instrument panel. 3 Battery Saver Feature To prevent battery drain if a door is left open or ajar, the interior lights will turn off automatically after 15 minutes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE EXTERIOR LIGHTS Headlights and Parking Lights When the headlight switch is turned clockwise from OFF to the first position, the parking lights, taillights, side marker lights, license plate lights and instrument panel lights are all illuminated. Lights-On Reminder If the headlights or parking lights are left on after the ignition is turned off, a warning will sound if the driver’s door is opened.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fog Lights To operate the fog lights, pull the headlight switch out one stop, with the parking lights and/or low beam headlights on. A light to the lower left of the headlight switch will illuminate when the fog lights are on. To turn off the fog lights, push the headlight switch in fully. Selecting high beam headlights will also turn off the fog lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MULTIFUNCTION CONTROL LEVER To operate the turn signals continuously, move the control lever up or down past the point of resistance. The operation is automatically canceled when the steering wheel is turned to a large enough degree. If one of the turn signal lights fail, the turn signal indicator system flashes and sounds at a faster than normal rate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlight Dimmer Switch Push the multifunction control lever toward the instrument panel to turn the headlights to high beam. Pull the lever toward you to switch to low beam. 65 Passing Light You can signal another vehicle with your headlights by lightly pulling the multifunction control lever toward the steering wheel. This will cause the headlights to turn on at high beam and remain on until the control lever is released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wipers And Washer The wipers and washer are operated by a switch in the multifunction control lever. Turn the end of the lever to select desired wiper speed: off, intermittent, normal, or fast. Mist Function Push the end of the multifunction control lever inward briefly for a single wipe without adding washer fluid. Use this feature only when the windshield is wet.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 TELESCOPING STEERING COLUMN Unlock the steering column by pulling out the handle located directly below the column. The indicator light located in the instrument cluster will come on. To lengthen or shorten the steering column, pull out or push in the steering wheel. Lock the steering column in position by pushing the handle in until it engages. The indicator light in the instrument cluster will go out.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the steering wheel while driving. The telescoping adjustment must be locked while driving. Adjusting the steering wheel while driving, or driving without the telescoping adjustment locked could cause the driver to lose control of the vehicle. NOTE: If the indicator light in the instrument cluster does not go out after starting the engine, the telescoping column is not locked properly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 NOTE: The pressure in your tires changes with temperature. A significant decrease in temperature could reduce cold inflation pressure below the TPM setpoint. For example, tires inflated to the proper cold inflation pressure on a warm day or in a warm garage could illuminate the TPM indicator lamp on the following day if the temperature is very cold. ALWAYS check the pressure in your tires if the TPM lamp is illuminated.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! The TPM system has been optimized for the original equipment tires and wheels. TPM system pressures have been established for the tire size equipped on your vehicle. Undesirable operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use aftermarket tire sealant or balance beads, as damage to the sensors may result.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR SPOILER A rear spoiler enhances vehicle stability. The rear spoiler deploys automatically when vehicle speed reaches 62 mph (100 km/h). The spoiler begins to retract at 39 mph (62 km/h). When retracted, the spoiler fits between the quarter panels, and aft of the liftgate window. 71 The spoiler can also be deployed at lower speeds using an override switch mounted in the center console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Should a malfunction occur that prevents the spoiler from deploying automatically, a red warning light will illuminate in the override switch and an audible warning will sound. WARNING! Do not drive the vehicle at speeds above 62 mph (100 km/h) if the red spoiler warning indicator is illuminated. You could have reduced vehicle stability and control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE BRAKE ASSIST SYSTEM (BAS) WARNING! BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. The BAS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE turned to the ON/RUN position. They should go out with the engine running. If the BAS/ESP malfunction indicator light comes on continuously with the engine running, a malfunction has been detected in either system. If the malfunction indicator light stays illuminated, have the BAS and ESP checked at your authorized dealer as soon as possible.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 3 To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, switch off the ESP system by pressing the upper half of the ESP switch. With the ESP system switched off, the engine torque reduction feature is cancelled. Therefore, the enhanced vehicle stability offered by ESP is unavailable. ESP always operates under braking, even with the switch in the OFF position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE as possible. Be sure to adapt your speed and driving to the prevailing road conditions. When the ESP warning light is illuminated continuously, the ESP is switched off. To return to the enhanced vehicle stability offered by ESP, press the lower half of the switch (the ESP warning light in the speedometer dial goes out). Avoid spinning one drive wheel. This may cause serious damage to the drive train and is not covered by the DaimlerChrysler warranty.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL The electronic speed control automatically maintains the set speed by actively regulating the throttle setting. Any speed above approximately 20 mph (30 km/h) can be maintained with the electronic speed control by operating the lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To accelerate and set a speed, lift the lever up. Lift and hold the lever to accelerate, or lift and release to set a speed. To decelerate and set a speed, press the lever down. Press down and hold the lever to decelerate, or press down and release to set a speed. WARNING! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate A soft tap on the brake pedal, or normal brake pressure while slowing the vehicle, will deactivate the speed control without erasing the memory. Pushing the speed control lever forward or turning the key in the ignition switch to the OFF/LOCK position will turn off the speed control and erase the memory. 79 To Resume Speed To resume a previously set speed, pull the speed control lever toward you, and then release.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Speed control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use speed control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 WARNING! WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature, as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features, as it could cause injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Step 3 does not have to be followed to program additional hand-held transmitters. 4. Choose one of the three buttons to program. Place the hand-held controller 1–3 inches (25–76 mm) from the universal transceiver while keeping its indicator light in view. NOTE: Some gate operators and garage door openers may require you to replace this Programming Step 5 with procedures noted in the “Gate Operator/Canadian Programming” section. 6.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming Steps 8-10 to complete programming of a rolling code equipped device (most commonly a garage door opener). 8. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 9. Firmly press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE signal has successfully been accepted by the universal transmitter. (The indicator light will flash slowly and then rapidly.) Proceed with Programming Step 6 to complete. Using the Universal Transceiver To operate the universal transceiver, simply press and release the programmed button. Activation will now occur for the programmed device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Security If you sell your vehicle, be sure to erase the frequencies. To erase all of the previously programmed frequencies, hold down both outside buttons until the light begins to flash. This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS m Instruments And Controls . . . . . . . . . . . . . . . . .88 m Compact Disc Maintenance . . . . . . . . . . . . . . . 109 m Instrument Cluster . . . . . . . . . . . . . . . . . . . . . .89 m Radio Antenna . . . . . . . . . . . . . . . . . . . . . . . . 110 m Instrument Cluster Description . . . . . . . . . . . . .89 m Radio Operation And Cellular Phones . . . . . . . 110 m “Infinity Modulus” AM/FM Stereo Radio With Single-Disc CD Player . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENTS AND CONTROLS
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER The instrument cluster displays are activated by either opening the door, pressing the left button within the cluster, or turning the key in the ignition switch to the ON/RUN position. 89 INSTRUMENT CLUSTER DESCRIPTION 1. Low Windshield Washer System Fluid Level Warning Light With the key in the ignition switch turned to the ON/RUN position, the indicator light comes on. It should go out when the engine is running.
UNDERSTANDING YOUR INSTRUMENT PANEL 2. Low Tire Pressure Indicator Light The tire pressure monitor (TPM) system uses wireless technology to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to a receiver located in the vehicle. If the light is illuminated, the pressure in one of the tires on the vehicle has dropped to at least 25% below the recommended pressure on the vehicle’s tire label.
UNDERSTANDING YOUR INSTRUMENT PANEL 91 WARNING! CAUTION! You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot. Continuing to drive with an overheated engine cooling system can cause damage to the engine or other components. 4.
UNDERSTANDING YOUR INSTRUMENT PANEL The arrows in the instrument cluster will flash in unison with the respective exterior turn signal. 7. Electronic Stability Program (ESP) Indicator Light The yellow ESP indicator light in the speedometer dial comes on with the key in the ignition switch turned to the ON/RUN position. It should go out with the engine running. If the ESP indicator light flashes during acceleration, apply as little throttle as possible. While driving, ease up on the accelerator.
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! Driving a vehicle with the brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately. NOTE: This light shows only that the parking brake is on. It does not show the degree of brake application. The brake warning light will come on if the ABS light is not functioning and there is an ABS system malfunction. 11.
UNDERSTANDING YOUR INSTRUMENT PANEL 13. Brake Assist Indicator Light The indicator light for the Brake Assist System (BAS) is combined with the Electronic Stability Program (ESP). This yellow indicator light in the instrument cluster comes on with the key in the ignition switch turned to the ON/RUN position. The BAS/ESP warning indicator light also comes on when a malfunction is detected in either the Brake Assist System or the Electronic Stability Program. It should go out with the engine running.
UNDERSTANDING YOUR INSTRUMENT PANEL 95 CAUTION! The display can be adjusted with the knob/button located to the left of the clock. The accessory drive belt also drives the water pump. Operating the vehicle with a failed belt can cause engine overheating and possible severe engine damage. 18. Gear Indicator For automatic transmission vehicles, the current gear shift selector range is indicated in the gear range indicator display. 16.
UNDERSTANDING YOUR INSTRUMENT PANEL • Press the button twice (with the key removed or in the OFF/LOCK or ACC position). 21. Main Odometer, Flexible Service System (FSS) This shows the total distance the vehicle has been driven. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct distance that the vehicle has been driven.
UNDERSTANDING YOUR INSTRUMENT PANEL The counter can also be reset by any individual after the indicated service has been performed. To do so: 1. Turn key to the ON/RUN position. 2. Within one second press the knob/button twice. 3. The present status for days or distance is displayed. Within 10 seconds turn the key to OFF/ LOCK. 4. Press and hold the knob/button, while turning the key to ON/RUN again. The present status for days or distance is displayed once more. Continue to hold the knob/button.
UNDERSTANDING YOUR INSTRUMENT PANEL starts combined with short distance driving in which the engine does not reach normal operating temperature, reduce the interval between services. However you choose to set your reference numbers, the scheduled services as posted in the Service Booklet must be followed to properly care for your vehicle. 23. Outside Temperature Display The temperature display is located on the left side of the instrument cluster, below the fuel and engine temperature gauges.
UNDERSTANDING YOUR INSTRUMENT PANEL the bulb is not lit during starting, have it replaced. If the light stays on, or comes on while driving, have the system checked by an authorized dealer. 99 WARNING! Do not drive the vehicle until you have properly locked the steering column. WARNING! In the event a malfunction of the airbag is indicated, the airbag may not be operational.
UNDERSTANDING YOUR INSTRUMENT PANEL If the vehicle is not driving normally, and the Check Engine light flashes or remains on continuously, it is an alert to serious conditions that could lead to loss of power or severe catalytic converter damage. The vehicle should be serviced at an authorized dealer as soon as possible. 27. Brake Wear Indicator Light With the key in the ignition and turned to the ON/RUN position, the brake wear indicator light comes on. The light goes out when the engine is running.
UNDERSTANDING YOUR INSTRUMENT PANEL The indicated amount of oil must be added to the engine if the message -2.0 Q (-2.0L) blinks and a signal sounds. The HI message indicates that the excess oil must be removed from the pan to avoid possible engine or catalytic converter damage. If the ISO oil level icon and “clock” icon remain on when attempting to check oil level and no message follows, or if the low engine oil level warning lamp comes on, a malfunction in the engine oil level system is indicated.
UNDERSTANDING YOUR INSTRUMENT PANEL Power/Volume Control To activate the audio system, press the ON/OFF knob on the left. If the unit was switched off using the ignition switch, it will switch on again with the ignition switch. • Treble (TREB) Press the ON/OFF knob within three seconds of turning the ignition switch off to prevent the radio from switching off.
UNDERSTANDING YOUR INSTRUMENT PANEL 103 NOTE: After six seconds without any action, or by pressing OPT, CD, AM, FM, or TP, the current setting is cancelled, and the new setting is stored. BEST FM – The BEST FM function automatically memorizes and continuously updates the frequencies of stations in order of their signal strength. FM1 – FM2 – FM AS – BEST FM The system has four FM memory modes that can be selected by repeatedly pressing the FM button.
UNDERSTANDING YOUR INSTRUMENT PANEL Beginning with the currently set frequency, the next station scanned will be heard for eight seconds. Press the right rotary control/push button if you wish to keep the current station. Once the scan begins, it will continue until either a station or program is retained or until another mode is selected.
UNDERSTANDING YOUR INSTRUMENT PANEL • REL MUSC – Religious Music • TOP 40 – Top 40 • REL TALK – Religious Talk • COUNTRY – Country Music • PERSNLTY – Personality • OLDIES – Oldies Format • PUBLIC – Public Radio • WEATHER – Weather Forecast • PTY 24-28 – Not Specified • NO PTY – No Program Type AM-AM AS The system has two AM modes available. Press the AM button repeatedly until the band or operation mode is selected.
UNDERSTANDING YOUR INSTRUMENT PANEL General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired operation. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
UNDERSTANDING YOUR INSTRUMENT PANEL • Fast Forward/Rewind (<<, >>) Press and hold the multifunction button >> for audible fast forward play. Press and hold the multifunction button << for audible fast rewind play. The relative time is displayed during this operation and continues for an additional eight seconds after releasing the function button. • Relative Time Display (T) Press the multifunction button T for the time of the currently playing track to be displayed for approximately eight seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL User Memory (USER – 1, 2, 3) You can program up to three user memories, which saves the sound settings, and the last received station when the unit is switched off. To activate, first enter the user menu. One of the three users can now be selected by turning the right rotary/push button. You can also call up the Mono/Stereo setting by pressing the right rotary/push button at this time.
UNDERSTANDING YOUR INSTRUMENT PANEL 109 Telephone mute characteristics If a telephone with hands-free operation is installed, the call may be routed through the speaker system. This eliminates the need for an additional speaker (if the signal lines are connected to the unit). The following settings are available: COMPACT DISC MAINTENANCE To keep the compact discs in good condition, take the following precautions: • PH MUTE – Switching radio to mute. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL RADIO ANTENNA The radio antenna is located in the rear liftgate glass and requires no maintenance. RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL The climate control system allows you to balance the temperature, amount and direction of the air circulating throughout the vehicle. The system is always at operational readiness, except when manually switched off. The climate control only operates with the engine running.
UNDERSTANDING YOUR INSTRUMENT PANEL Select a temperature for each side of the passenger compartment. Select air volume with the fan control switch. Then select the Bi-Level setting on the air distribution control switch to force air from both the upper panel outlets and the floor outlets. Basic Setting - Air Conditioner Press the air conditioning ON/OFF switch. The light in the switch will illuminate. Select a temperature for each side of the passenger compartment.
UNDERSTANDING YOUR INSTRUMENT PANEL 113 Defrosting Set the temperature selectors to the maximum heating position, set the fan control to position 5, and the air distribution to the defrost position. Close the center air outlets. Close the left and right side air outlets. Turn the defroster outlets for the side windows to the detent position. Defogging Windows Fogged Up On Inside Press the A/C button; the indicator light should illuminate.
UNDERSTANDING YOUR INSTRUMENT PANEL Ventilation To receive outside air through the panel outlets, turn off the Air Conditioning ON/OFF switch. The light in the switch should be off. Set the controls as above for basic air conditioning. Climate Control - OFF To switch the climate control off, set the air volume control switch to position 0. The fresh air supply to the vehicle interior is shut off. While driving, use this setting only temporarily, otherwise the windshield could fog up.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! To avoid damaging the electrical conductors, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the rear window. Labels can be peeled off by soaking with warm water. Air Recirculation/REST This mode can be selected to temporarily reduce the entry of annoying odors or dust into the vehicle’s interior. Outside air does not flow into the vehicle’s interior. To select, press the recirculation button.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: This vehicle is equipped with an air conditioner system that uses R-134a (HFC: hydrofluorocarbon) as a refrigerant. Repairs should always be performed by a qualified technician, and refrigerant should be collected in a recovery system for recycling. Dust Filter Nearly all dust particles and pollen are filtered out before outside air enters the passenger compartment through the air distribution system.
STARTING AND OPERATING CONTENTS m Starting Procedures . . . . . . . . . . . . . . . . . . . . 119 ▫ Park Position . . . . . . . . . . . . . . . . . . . . . . . . 125 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 119 ▫ Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 ▫ Extremely Cold Weather (Below -20°F Or -29°C) . . . . . . . . . . . . . . . . . 120 ▫ Neutral . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 ▫ If Engine Fails To Start . . . . . . . . . . .
STARTING AND OPERATING ▫ Electronic Stability Program (ESP) . . . . . . . . . 133 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . . 146 ▫ Synchronizing ESP . . . . . . . . . . . . . . . . . . . . 135 ▫ Tire Rotation Recommendations . . . . . . . . . . . 147 ▫ ESP Control Switch . . . . . . . . . . . . . . . . . . . . 135 ▫ Alignment And Balance . . . . . . . . . . . . . . . . . 149 ▫ Anti-Lock Brake System (ABS) . . . . . . . . . . . . 136 m Fuel Requirements . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES WARNING! Do not leave animals or children inside parked vehicles in hot weather; interior heat build up may cause serious injury or death. Be sure that the parking brake is engaged and that selector lever is in the NEUTRAL or PARK position (gearshift lever in Neutral). Turn the key in the ignition switch to the ON/RUN position. Apply the brakes before shifting into any driving gear.
STARTING AND OPERATING NOTE: Due to the starter non-repeat feature, the key must be turned completely to the left before attempting to start the engine again. If Engine Fails to Start CAUTION! Do not try to push or tow your vehicle to get it started. Your vehicle cannot be started this way. Pushing with another vehicle may damage the transmission or the rear of your vehicle. See Section 6 of this manual for proper jump-starting procedures.
STARTING AND OPERATING accelerator pedal all the way to the floor and hold it there while cranking the engine. This should clear any excess fuel in case the engine is flooded. 121 After Starting The idle speed will automatically decrease as the engine warms up. TRANSMISSION SHIFTING CAUTION! Manual Transmission To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again.
STARTING AND OPERATING Fully depress the clutch pedal before you shift gears. As you release the clutch pedal, lightly depress the accelerator pedal. NOTE: During cold weather, until the transmission lubricant has warmed, you may have difficulty shifting. This is normal and not harmful to the transmission. Be sure the transmission is in FIRST gear, (not THIRD), when starting from a stopped position. Damage to the clutch can result from starting in THIRD.
STARTING AND OPERATING WARNING! 123 Automatic Transmission When leaving the vehicle, always remove the key from the ignition switch, and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Children could move the gearshift lever, which could result in an accident or serious injury. 5 WARNING! Skipping more than one gear while downshifting could cause you to lose control of your vehicle. You could have an accident.
STARTING AND OPERATING The gear shifting process is continuously adapted, dependent on the driving style, the driving situation and the road characteristics. The selector lever is automatically locked while in the PARK position. To move the selector lever out of the PARK position, the brake pedal must be firmly depressed before the shift lock will release. Shift the selector lever to the desired position only when the engine is idling normally and the brake pedal is applied.
STARTING AND OPERATING 125 Maneuvering To maneuver in tight areas, control the vehicle speed by gradually releasing the brakes. Accelerate gently and never abruptly step on the accelerator. To rock a vehicle out of soft ground (mud or snow), alternately shift from forward to reverse, while applying only slight acceleration. Rocking a vehicle free in this manner may cause the ABS or traction system malfunction indicator light to come on.
STARTING AND OPERATING Neutral No power is transmitted from the engine to the drive axle. When the brakes are released, the vehicle can be moved freely (pushed or towed). Do not engage in NEUTRAL position while driving except to coast when the vehicle is in danger of skidding (e.g., on icy roads). NOTE: Coasting the vehicle, or driving for any other reason with selector lever in NEUTRAL can result in transmission damage that is not covered by the Limited Warranty.
STARTING AND OPERATING into another gear that allows for quicker acceleration or to slow the vehicle down is possible. Downshifts can also be performed. Press and hold the selector lever in the “D-” direction. The transmission will shift from the current gear directly to the best gear for acceleration. NOTE: To avoid overrevving the engine when the selector lever is moved in “D-” direction, the transmission will not shift to a lower gear if the engine’s revolutions per minute limit would be exceeded.
STARTING AND OPERATING Gear Ranges “P” PARK NOTE: If the key is in the ON/RUN position, you must press the brake pedal to shift out of the PARK position. Program mode selector switch The transmission is provided with a selector switch for Standard “S” and Winter/Wet “W” (snow and ice) program modes. PARK supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to use PARK while the vehicle is in motion.
STARTING AND OPERATING Depressing the accelerator pedal rapidly or nearly to the floor while driving (kickdown position), rather than depressing the accelerator pedal in slow, small movements, will cause the automatic transmission to shift down into a lower gear. Rapid release of the accelerator pedal will normally result in an upshift. This gear shifting process is dependent on the current vehicle speed. For Winter/Wet (snow and ice) mode, press the “W” symbol on the switch.
STARTING AND OPERATING Have the transmission checked at your authorized dealer as soon as possible. PARKING BRAKE When you apply the parking brake with engine running, the brake system warning light in the instrument cluster will come on. NOTE: This light, when illuminated with parking brake application, shows only that the parking brake is on. It does not show the degree of brake application. NOTE: If the light remains on with the parking brake released, a brake system malfunction is indicated.
STARTING AND OPERATING precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied when the driver is not in the vehicle. WARNING! Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and an accident. WARNING! Do not leave children unattended in a vehicle. A child could be injured, or could injure others, if left unattended.
STARTING AND OPERATING BAS assistance. To receive the benefit of the system you must apply continuous, full braking power during the stopping sequence. Do not reduce brake pedal pressure. The malfunction indicator light for the BAS is combined with the Electronic Stability Program (ESP) malfunction indicator light.
STARTING AND OPERATING 133 system. As a result, it is possible that only partial engine output will be available, and pressing the accelerator pedal will require more effort. If the BAS malfunctions, the brake system functions in the usual manner, but without BAS. With the ABS malfunctioning, the BAS and ESP will be disabled. In this condition, both malfunction indicator lights come on while the engine is running.
STARTING AND OPERATING WARNING! CAUTION! ESP cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded. The ESP cannot prevent accidents, including those resulting from excessive speed in turns, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents. The capabilities of an ESP equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others.
STARTING AND OPERATING Synchronizing ESP If the power supply was interrupted (battery disconnected or discharged), the BAS/ESP malfunction indicator light may be illuminated with the engine running. To re-synchronize the ESP, and cancel the malfunction indicator light, the steering angle sensor will need to be recalibrated. 135 ESP Control switch The ESP control switch is located in the center console. When the ESP is switched off, the warning light in the instrument cluster comes on.
STARTING AND OPERATING illuminated. With the ESP system switched off, the engine torque reduction feature is cancelled. Therefore, the enhanced vehicle stability offered by ESP is unavailable. CAUTION! Snow chains should never be used without the recommended mud and snow (M+S) rated radial-ply tires. Damage to your vehicle may result from such usage. ESP always operates under braking, even with the switch in the OFF position.
STARTING AND OPERATING In the case of an emergency brake maneuver, keep continuous full pressure on the brake pedal. In this manner only can the ABS be most effective. On slippery road surfaces, the ABS will respond even with light brake pedal pressure because of the increased likelihood of locking wheels. The pulsating brake pedal can be an indication of hazardous road conditions and functions as a reminder to take extra care while driving.
STARTING AND OPERATING briefly during this procedure, or remains on after the engine is running, have the system checked by an authorized dealer. below 10 volts, the malfunction indicator light comes on and the ABS is switched off. When the voltage is above this value again, the malfunction indicator light should go out and the ABS is operational. If the malfunction indicator light stays illuminated, have the system checked at your authorized dealer as soon as possible.
STARTING AND OPERATING WARNING! To use your brakes and accelerator more safely, follow these tips: • Do not “ride” the brakes by resting your foot on the pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping distances, or brake damage. • When descending mountains or hills, repeated braking can cause brake fade with loss of braking control. Avoid repeated heavy braking by downshifting the transmission whenever possible.
STARTING AND OPERATING TIRES Please take the time to read the tire warranty booklet in your Owner’s Manual package. It contains valuable information on tire maintenance. Specific recommendations on guidelines for long-term tire storage should be requested of the tire manufacturer. Please refer to the tire warranty booklet for contact information. 1. Safety NOTE: Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left.
STARTING AND OPERATING 141 3. Ride Comfort And Vehicle Stability Proper tire inflation contributes to a comfortable ride. Over-inflation produces a jarring and uncomfortable ride. Both under-inflation and over-inflation affect the stability of the vehicle and can produce a feeling of sluggish response or over-responsiveness. Unequal tire pressures can cause erratic and unpredictable steering response.
STARTING AND OPERATING Tire Pressure Monitor System The Tire Pressure Monitor System (TPM) monitors the pressure in all tires. The TPM system uses wireless technology to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to a computer which monitors for low pressure. If low pressure is measured, the TPM Indicator Light will illuminate. The TPM system informs you of a low tire pressure condition.
STARTING AND OPERATING reduce cold inflation pressure below the TPM setpoint. For example, tires inflated to the proper cold inflation pressure on a warm day or in a warm garage could illuminate the TPM indicator lamp on the following day if the temperature is very cold. ALWAYS check the pressure in your tires if the TPM lamp is illuminated. High Speed Operation DaimlerChrysler Corporation advocates driving at safe speeds within posted speed limits.
STARTING AND OPERATING When driving with tire chains, press the ESP control switch to OFF. CAUTION! Damage to the vehicle may result if unapproved tire chains are used. Original Equipment Tires Your vehicle is equipped with either sport performance tires or all-season performance tires. The sport performance tires offer the maximum road handling capability in dry and wet weather conditions.
STARTING AND OPERATING 145 tire also requires the purchase of two additional wheels with the same size specification as the original equipment front wheels. Snow tires may have a lower speed rating than factory equipped tires and may not match the maximum vehicle speed. Snow tires should not be operated at sustained speeds over 75 mph (120 km/h). Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced.
STARTING AND OPERATING Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct inflation pressure. DaimlerChrysler Corporation strongly recommends that you use tires equivalent to the originals in size, quality and performance when replacement is needed (see the paragraph on tread wear indicators). Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle.
STARTING AND OPERATING 147 WARNING! CAUTION! Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING Rotate your tires at intervals shown on the maintenance schedules. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected before rotating.
STARTING AND OPERATING Alignment And Balance The suspension components of your vehicle should be inspected and aligned when needed to obtain full tire tread mileage. Poor suspension alignment may result in: • Fast tire wear • Uneven tire wear, such as feathering and one-sided wear • Vehicle pull to right or left Tires may also cause vehicle to pull to the left or right. Alignment will not correct this condition. See your authorized dealer for proper diagnosis.
STARTING AND OPERATING fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle. DaimlerChrysler Corporation recommends the use of gasolines that meet the WWFC specifications if they are available. Reformulated Gasoline Many areas of the country require the use of cleaner burning fuel, referred to as “Reformulated Gasoline”. Reformulated gasolines contain oxygenates and are specially blended to reduce vehicle emissions and improve air quality.
STARTING AND OPERATING without MMT. Gasolines blended with MMT have shown to reduce spark plug life and reduce emission system performance in some vehicles. DaimlerChrysler Corporation recommends using gasolines without MMT. Since the MMT content of gasoline may not be indicated on the pump, you should ask your gasoline retailer whether or not his/her gasoline contains MMT. MMT is prohibited in both Federal and California reformulated gasolines.
STARTING AND OPERATING CAUTION! CAUTION! If the CHECK ENGINE Light is flashing, immediate service is required. See the Onboard Diagnostic System (OBDII) paragraph in the Maintaining Your Vehicle section of this manual. Damage to the fuel system or emission control system could result from using an improper gas cap. A poorly fitting cap could let impurities into the fuel system. The CHECK ENGINE light will come on if the gas cap is not properly secured.
STARTING AND OPERATING If the warning light does not go out after starting the engine, or if it comes on while driving, it indicates that the fuel level is down to the reserve quantity of approximately 2.1 gallons (8 liters). Leaving the engine running and the fuel cap open can cause the CHECK ENGINE light to illuminate. NOTE: • When the fuel nozzle “clicks” or shuts off, the fuel tank is full. • Tighten the gas cap until you hear a single click.
STARTING AND OPERATING VEHICLE LOADING The load carrying capacity of your vehicle is in the following chart and on the tire pressure label attached to the driver door pillar. Vehicle Loading Capacities Front Seat Occupants . . . . . . . . . . . . . . . . . . . . . . . 2 Cargo Capacity (with two persons) . . . . 115 lbs. (52 kg) Rated Vehicle Capacity. . . . . . . . . . . . 415 lbs. (188 kg) Roof Luggage Rack External racks do not increase the total load carrying capacity of the vehicle.
STARTING AND OPERATING 155 WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof luggage rack “Cautions” when carrying cargo on your roof rack. 5 TRAILER TOWING Trailer towing with your Crossfire is not recommended.
WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Flasher . . . . . . . . . . . . . . . . . 158 m Driving On Slippery Surfaces . . . . . . . . . . . . . 169 m If Your Engine Overheats . . . . . . . . . . . . . . . . 158 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 m TIREFIT Tire Repair And Jacking . . . . . . . . . . 160 m Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 170 ▫ TIREFIT . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is located in the console. Push in the flasher switch and all front and rear directional signals will flash. Press the flasher switch a second time to turn the flashers off. NOTE: With extended use, the flasher may run down your battery. IF YOUR ENGINE OVERHEATS During severe operating conditions and stop-and-go city traffic, the coolant temperature may rise close to the red area on the gauge.
WHAT TO DO IN EMERGENCIES NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the cooling system and turning off the A/C removes this heat. You can also turn the temperature control to maximum heat, the mode control to floor, and the fan control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the cooling system.
WHAT TO DO IN EMERGENCIES TIREFIT TIRE REPAIR AND JACKING 1. TIREFIT sealant bottle TIREFIT Small punctures, particularly those in the tread, can be sealed with TIREFIT. Foreign objects (e.g., screws or nails) should not be removed from the tire. TIREFIT can be used in outside temperatures down to approximately -4°F (-20°C). 2. Air pump flap 3. Recess in air pump 4. Power plug and cable 5. Air pump hose with pressure gauge 6.
WHAT TO DO IN EMERGENCIES WARNING! Cuts or punctures larger than approximately 0.16 in. (4 mm), tire damage caused by driving with extremely low tire pressure or on a flat tire, or a damaged wheel can pose a hazard while driving. TIREFIT should not be used in such circumstances. Do not drive the vehicle under such circumstances. Contact your nearest authorized dealer for assistance. Take care not to allow the contents of TIREFIT to come in contact with hair, eyes or clothing.
WHAT TO DO IN EMERGENCIES 10. Insert the power plug (4) into the power point on the instrument panel. 17. Drive the vehicle for about 10 minutes to ensure optimum distribution of the tire sealant within the tire. 11. Turn the ignition key to the ON/RUN position. 18. Check the pressure in the tire. If the pressure is above 19 psi (1.3 bar), inflate the tire to the pressure indicated on the tire pressure label on the driver side latch pillar. 12. Press the switch on the air pump to 1.
WHAT TO DO IN EMERGENCIES wheel components. Once TIREFIT sealing material has dried, it can easily be peeled off and properly discarded. Preparations for Jacking WARNING! 163 Jacking the vehicle should only be necessary in the event that a tire has been severely damaged, and must be replaced. (See TIREFIT Tire Repair section for a description of cuts and punctures that may be repairable with TIREFIT.) Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you.
WHAT TO DO IN EMERGENCIES • Turn off the engine. • Block the wheel diagonally opposite the flat tire. NOTE: The jack is designed exclusively for jacking up the vehicle at the specified jack location points built beneath either side of the vehicle. Jack Location and Instructions • Passengers must not remain in the vehicle when the vehicle is jacked. 1. Remove the jack and jack handle from stowage in the rear liftgate area.
WHAT TO DO IN EMERGENCIES 165 2. The lifting points for the jack are located beneath the outer edge of the body side, directly behind the front wheel housings, and in front of the rear wheel housings.
WHAT TO DO IN EMERGENCIES NOTE: Do not raise the vehicle until you are sure the jack is securely engaged, as shown. 5. Lower the vehicle by cranking the handle counterclockwise, then remove the jack assembly. NOTE: Before storing the jack, it should be fully collapsed. 6. Ensure proper tire pressure. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to make the necessary repair. 3.
WHAT TO DO IN EMERGENCIES JUMP-STARTING THE BATTERY WARNING! Take care to avoid the radiator cooling fan whenever the hood is raised. It can start any time the ignition switch is on. You can be hurt by the fan. CAUTION! Do not try to push or tow your vehicle to get it started. Your vehicle cannot be started this way. Pushing with another vehicle may damage the transmission or the rear of your vehicle.
WHAT TO DO IN EMERGENCIES 3. Turn off the heater, radio and all unnecessary electrical loads. 1. Wear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. 2. When boost is provided by a battery in another vehicle, park that vehicle within booster cable reach but without letting the vehicles touch. Set the parking brake, place the transmission in Neutral and turn the ignition OFF for both vehicles. 4.
WHAT TO DO IN EMERGENCIES 6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fans. NOTE: If engine does not run after several unsuccessful starting attempts, have it checked at the nearest authorized dealer.
WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE In order to free a stuck vehicle you must turn off the Electronic Stability Program (ESP) before attempting to “rock” the vehicle. If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth between Reverse and Drive.
WHAT TO DO IN EMERGENCIES 171 CAUTION! CAUTION! If the vehicle is towed with the front wheels raised, the engine must be shut off (key in the ignition switch turned to the OFF/LOCK or ACC positions). Otherwise, the ESP will immediately be engaged and will apply the rear wheel brakes. Switch off the tow-away alarm as well as the automatic central locking system. • Do not attempt to tow this vehicle from the front with sling-type towing equipment. Damage to the front fascia will result.
WHAT TO DO IN EMERGENCIES located behind the lower grille in the fascia. For access, a snap-in grille must be removed using the multifunction tool from the glovebox.
WHAT TO DO IN EMERGENCIES 173 Insert the tool (or similar sized screwdriver) into the slot in the grille as shown, and rotate it to the left to detach. The front towing eye is now accessible.
WHAT TO DO IN EMERGENCIES Tow-Away Alarm Once the alarm system has been armed, the exterior vehicle lights will flash and an alarm will sound when anyone attempts to raise the vehicle for towing. The alarm will last approximately three minutes in the form of flashing exterior lights. At the same time, an alarm will sound for 30 seconds. The alarm will stay on even if the vehicle is immediately lowered.
MAINTAINING YOUR VEHICLE CONTENTS m 3.2L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 177 ▫ Power Steering Fluid . . . . . . . . . . . . . . . . . . . 189 m Onboard Diagnostic System (OBD II) . . . . . . . 178 ▫ Chassis Lubrication . . . . . . . . . . . . . . . . . . . . 190 m Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . . 190 m Replacement Parts . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Manual Transmission . . . . . . . . . . . . . . . . . . 200 ▫ Front And Rear Sidemarker Lights . . . . . . . . . 214 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 ▫ Tail, Stop, Back Up And Turn Signal Lights . . . 214 m Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206 ▫ Engine Compartment Fuses . . . . . . . . . . . . . . 206 ▫ Relay Control Module Fuses . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 177 3.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) To meet new government regulations and promote cleaner air, your Crossfire is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions and engine control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the CHECK ENGINE Light is functioning and is not on when the engine is running, and that the OBD (Onboard Diagnostic) system is ready for testing.
MAINTAINING YOUR VEHICLE If your OBD system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update. A recheck with the above test routine may then indicate that the system is now ready.
MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent technician. MAINTENANCE PROCEDURES The pages that follow contain the maintenance service recommended by the engineers who designed your vehicle.
MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off, or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between the MIN and MAX markings on the dipstick. Adding one quart of oil when the reading is at the MIN mark will result in a MAX reading on this engine.
MAINTAINING YOUR VEHICLE Change Engine Oil The oil change interval for your Crossfire is initially set at 7,000 miles (11,000 km). The Flexible Service System (FSS) in your vehicle evaluates engine temperature, oil level, vehicle speed, engine speed, distance driven, and the time elapsed since your last service. It determines when your vehicle needs maintenance service and alerts you in advance. The next necessary service is indicated by the FSS in your instrument cluster.
MAINTAINING YOUR VEHICLE Engine Oil Selection Only use synthetic engine oils, approved to MB 229.3 or MB 229.5, such as Mobil 1 SAE 0W-40. The FFS may not alert for an oil change at the proper interval if an unapproved engine oil is used; engine damage and reduced engine life may result. Disposing of Used Engine Oil Care should be taken in disposing of used engine oil from your vehicle. Used oil, indiscriminately discarded, can present a problem to the environment.
MAINTAINING YOUR VEHICLE Inspect the drive belts for evidence of cuts, cracks, or glazing and replace them if there is any sign of damage which could result in belt failure. If adjustment is required, adjust the belts according to the specifications and procedures shown in the Service Manual. Special tools are required to properly measure tension and to restore belt tension to factory specifications.
MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly serviced to assure proper catalyst operation and prevent possible catalyst damage. If the CHECK ENGINE light is flashing, immediate service is required. CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
MAINTAINING YOUR VEHICLE • Do not idle the engine with any spark plug wires disconnected for a prolonged period. Ignition Wiring System The ignition cables should be kept clean and properly connected. Terminals should be fully seated. Cracked, damaged, or faulty cables should be replaced. Crankcase Emission Control System Proper operation of this system depends on freedom from sticking or plugging due to deposits. Check ventilation hose for indication of damage or plugging deposits. Replace if necessary.
MAINTAINING YOUR VEHICLE CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion. Apply grease to posts and clamps after tightening.
MAINTAINING YOUR VEHICLE Power Steering Fluid No power steering fluid service is required. The system is filled at the factory with Pentosin CHF 11S. Steering noise and reduced component life may result if an unapproved fluid is used. 189 Before removing the reservoir cap, wipe the outside of the cap and reservoir so that no dirt can fall into the reservoir. The power steering pump has a dipstick. Fluid level should be maintained at the proper level indicated on the dipstick.
MAINTAINING YOUR VEHICLE Chassis Lubrication Front Suspension Ball Joints There are two front suspension lower ball joints that are permanently lubricated. Inspect these ball joints whenever under-vehicle service is done. Steering Linkage Inspect tie rod ends whenever the vehicle is serviced. They are permanently lubricated and do not require periodic lubrication. Drive Shaft Universal Joints Your vehicle has four constant velocity universal joints.
MAINTAINING YOUR VEHICLE lubricant. Repeat this procedure three or four times. Wipe all the lubricant off the key with a clean cloth, to avoid soiling clothing. Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non-abrasive cleaner, or use the washer solvent. This will remove accumulations of salt or road film and help reduce streaking and smearing. 191 Windshield Wiper Blade Replacement 1.
MAINTAINING YOUR VEHICLE Windshield Washer Reservoir The washer fluid reservoir is located in the engine compartment and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) rated not to freeze at -25°F (-31°C). Operate the system for a few seconds to flush out the residual water. WARNING! Do not overfill the washer reservoir. Do not attempt to fill to the top of the filler neck.
MAINTAINING YOUR VEHICLE If you notice a change in the sound of the exhaust system, or if exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent technician inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment.
MAINTAINING YOUR VEHICLE Check the front of the radiator and condenser for an accumulation of bugs, leaves, etc. Clean the radiator and condenser by gently spraying water from a garden hose at the back of the radiator core. If the solution is dirty and contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals.
MAINTAINING YOUR VEHICLE CAUTION! Failure to use the proper antifreeze could cause radiator plugging and engine overheating. Do not mix antifreeze brands or types. Do not use plain water alone or alcohol base antifreeze products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator coolant and may plug the radiator. Adding Coolant When adding coolant, a minimum solution of 50% ethylene glycol antifreeze coolant and water should be used.
MAINTAINING YOUR VEHICLE WARNING! Do not use a pressure cap other than the one specified for your vehicle. Personal injury or engine damage may result. Points to Remember NOTE: When the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine compartment.
MAINTAINING YOUR VEHICLE Hoses And Vacuum/Vapor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage. Hard or soft spots, brittle rubber, cracking, checking, tears, cuts, abrasions, and excessive swelling indicate deterioration of the rubber. Pay particular attention to the hoses nearest to high heat sources such as the exhaust manifold.
MAINTAINING YOUR VEHICLE NOTE: Often, fluids such as oil, power steering fluid, and brake fluid are used during assembly plant operations to ease the assembly of hoses to couplings. Therefore, oil wetness at the hose-coupling area is not necessarily an indication of leakage. Actual dripping of hot fluid when systems are under pressure (during vehicle operation) should be noted before hose is replaced based on leakage.
MAINTAINING YOUR VEHICLE Use brake fluid approved to MB 331.0, or a DOT 4 brake fluid with: minimum dry boiling point (ERBP) 500°F, minimum wet boiling point (WERBP) 356°F, maximum viscosity 1500 mm2/s, conforming to FMVSS 116 and ISO 4925. WARNING! Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident.
MAINTAINING YOUR VEHICLE CAUTION! Using a transmission fluid other than the fluid recommended by DaimlerChrysler Corporation may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the DaimlerChrysler Corporation will result in more frequent fluid and filter changes. Refer to the Recommended Fluids, Lubricants and Genuine Parts section for correct fluid type.
MAINTAINING YOUR VEHICLE CAUTION! Do not overfill. Dirt and water in the transmission can cause serious damage. To prevent dirt and water from entering the transmission after checking or replenishing fluid, make certain that the dipstick cap is seated properly. Add fluid, if necessary, to maintain the proper level. Frequency of Fluid Change Under normal operation conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle.
MAINTAINING YOUR VEHICLE What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. • Use Mopart auto polish to remove road film and stains and to polish your vehicle. Take care never to scratch the paint. The most common causes are: • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. • Road salt, dirt and moisture accumulation. • Stone and gravel impact.
MAINTAINING YOUR VEHICLE • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • Use Mopart touch-up paint on scratches or chips as soon as possible. Your dealer has touch-up paint to match the color of your vehicle. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as possible.
MAINTAINING YOUR VEHICLE • A car wash that uses carbide-tipped wheel cleaning brushes or acidic solutions. CAUTION! leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, detergents, or ammonia based cleaners to clean your leather upholstery. Application of a leather conditioner is not required to maintain the original condition. Many wheel cleaners contain acids that may harm the wheel surface.
MAINTAINING YOUR VEHICLE Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses.
MAINTAINING YOUR VEHICLE FUSES Engine Compartment Fuses The engine compartment fuses are located under the hood on the driver’s side, between the brake master cylinder and the left front fender. To remove the lid, squeeze the tabs together located at the front of the fusebox. Then lift the lid up by the tabs. The lid will then slide off the top of the fuse box. To replace the lid, place the two hinge-like tabs at the rear of the lid under the tabs on the fusebox.
MAINTAINING YOUR VEHICLE 207 CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it shows a problem in the circuit that must be corrected.
MAINTAINING YOUR VEHICLE Engine Compartment Fuses Cavity 1 2 3 4 5 6 7 8 Fuse 5 Amp Beige 5 Amp Beige 5 Amp Beige 30 Amp Green 15 Amp Blue 15 Amp Blue 5 Amp Beige 15 Amp Blue Circuits Garage Door Opening Signal, TPM and Seat Heater Occupant Restraint Controller Passenger Airbag Off Indicator, Safety Restraint System and Indicator, Passenger Airbag Off Wiper Motor Cavity 9 Fuse 10 Amp Red 10 5 Amp Beige 15 Amp Blue 10 Amp Red 10 Amp Red 20 Amp Yellow 5 Amp Beige 11 12 13 Radio 14 Exterior Mi
MAINTAINING YOUR VEHICLE Cavity 20 21 22 23 24 25 26 30 31 32 33 Fuse 10 Amp Red 30 Amp Green 30 Amp Green 15 Amp Blue 30 Amp Green 20 Amp Yellow 20 Amp Yellow 15 Amp Blue 15 Amp Blue 5 Amp Beige Circuits Spoiler Motor Cavity 34 35 Seat Adjustment Right Side Fuse 15 Amp Blue Seat Adjustment Left Side 36 Sound Booster (Amplifier) 37 Seat Heater Pneumatic Control Unit, Rear Window Defroster Central Locking Spare Cigar Lighter, Glove Compartment Light Wiper, Washer Pump, Headlight Flasher Residual Engin
MAINTAINING YOUR VEHICLE Relay Control Module Fuses The relay control module fuses are located in the Control Module Box next to the battery in the engine compartment. Slide the control module box cover retaining clips forward and lift the cover from the control module box to gain access to the relay control module fuses.
MAINTAINING YOUR VEHICLE Cavity 5 6 Fuse 15 Amp Blue 15 Amp Blue 211 Circuits Fuel Pump Horn Interior Fuses Interior Fuses Cavity 1 2 3 The fuse access door is located on the end of the instrument panel on the driver’s side behind the trim panel cover. Use a coin or flat blade screwdriver to open and close this access door. 4 Fuse 15 Amp Blue 7.
MAINTAINING YOUR VEHICLE Cavity 5 6 7 8 9 10 11 12 13 14 Fuse 7.5 Amp Brown 15 Amp Blue 7.5 Amp Brown 15 Amp Blue 15 Amp Blue 7.5 Amp Brown 7.5 Amp Brown 7.
MAINTAINING YOUR VEHICLE 213 EXTERIOR LIGHT BULB SERVICE Headlights WARNING! Halogen lamps contain pressurized gas. A bulb can explode if you: • touch or move it when hot, • drop the bulb, • scratch the bulb Wear eye and hand protection. NOTE: To prevent a possible electrical short circuit, switch off light prior to replacing a bulb. 1. Push the tab down at the top end of the cover and remove. 2. Disconnect the electrical connector. 3.
MAINTAINING YOUR VEHICLE Front Turn Signal and Parking/Standing Lights • Twist the bulb socket counterclockwise and pull out. Push the bulb into the socket, turn counterclockwise and remove. • Replace the bulb, push in and twist clockwise. Reinstall the socket, and turn clockwise. Front and Rear Sidemarker Lights 1. Push the front sidemarker assembly in and slide it forward. Push the rear sidemarker assembly in and slide rearward. The assembly will release from the fascia. 2.
MAINTAINING YOUR VEHICLE 4. Replace the access door in the trim panel. 215 NOTE: Always test the operation of all lights after service operations have been performed to validate an effective repair. 7 License Plate Light 1. Remove the two lens assembly mounting screws. 2. Pull the bulb out of the socket. 3. Replace the bulb and reattach the lens assembly. 4. Align and resecure the two lens assembly mounting screws.
MAINTAINING YOUR VEHICLE the vehicle and then readjust the headlights to the original position. If any further adjustments are necessary contact your manufacturer’s dealer. A detailed service procedure is contained in the manufacturer’s Service Manual. Information on purchasing a Service Manual can be found at the back of this Owner’s Manual. • If the vehicle will be subjected to freezing temperatures, remove the battery and store it in a dry, wellventilated place.
MAINTAINING YOUR VEHICLE 217 Check the battery every four to six weeks to ensure that the voltage is above 12.40. Voltage will drop more rapidly in hot temperatures. If battery voltage drops below 12.40, follow the battery recharge procedure in the Service Manual. • For long term storage, remove the tires and put the vehicle up on blocks. Stack the tires on plywood and cover with a tarp to prevent flat spotting. • Check that the radiator coolant level of protection is to at least -20°F (-29°C).
MAINTAINING YOUR VEHICLE Performance Specifications (approximate) SPECIFICATIONS Engine Specifications Engine Size Mode of Operation No. of Cylinders Horsepower (SAE J 1349) Bore Stroke Torque (SAE J 1349) Firing Order Compression Ratio Spark Plugs Spark Plug Gap Tightening Torque Maximum Engine Speed Accessory Drive Belt 195.2 CID (3.2 Liters) 4–stroke engine, gasoline injection 6 215 hp (160 kW) @ 5700 rpm 3.54 in. (89.90 mm) 3.30 in. (84.00 mm) 229 ft. lbs.
MAINTAINING YOUR VEHICLE Gear Ratios - 5-Speed Automatic Transmission First Second Third Fourth Fifth Reverse 3.95 2.423 1.486 1.00 0.833 3.147/1.93 219 Body Specifications Overall Length Maximum Width Maximum Width With Mirrors Overall Height Front Track Rear Track Wheelbase Front Overhang Rear Overhang Front Ground Clearance Rear Ground Clearance Turning Radius Weight Maximum Vehicle Load Luggage Capacity 159.8 in. (4058 mm) 69.5 in. (1766 mm) 76.9 in. (1954 mm) 51.5 in. (1307 mm) 58.8 in.
MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. 15.8 Gallons 2.1 Gallons Metric 60.0 Liters 8.0 Liters 3.2 L Engine 8.5 Qts. 8.0 Liters 3.2 L Engine 11.8 Qts. 1.9 Qts. 8.5 Qts. 1.4 Qts. 1.1 Qts. .5 Qts. 7.4 Qts. 11.2 Liters 1.8 Liters 8.0 Liters 1.3 Liters 1.0 Liters .5 Liters 7.
MAINTAINING YOUR VEHICLE 221 RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Spark Plug Gap Fuel Selection Fluids, Lubricants and Genuine Parts Use coolant approved to MB 325.0, such as Valvoline GO5, or an equivalent extended life coolant. Only use synthetic engine oils, approved to MB 229.3 or MB 229.5, such as Mobil 1 SAE 0W-40.
MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Brake Master Cylinder Clutch Fluid Manual Transmission Fluid Power Steering Reservoir Rear Axle Fluid Tire Pressure Fluids, Lubricants and Genuine Parts Only use ATF approved to MB 236.10, MB 236.12. Synthetic Dexron IIIt Transmission Fluid may be substituted. Use brake fluid approved to MB 331.
MAINTAINING YOUR VEHICLE 223 Body Component Hinges: Fluids, Lubricants and Genuine Parts Door Mopart Spray White Lube Liftgate / Decklid Mopart Multi-Purpose Lube NLGI Grade 2 EP, GC-LB Hood Springs and Links Mopart Spray White Lube Latches: Liftgate/Decklid Hood/Safety Catch Door Seat Regulator and Track Window System Components Lock Cylinders Spoiler Mopart Mopart Mopart Mopart Mopart Mopart Mopart Spray White Lube Multi-Purpose Lube NLGI Grade 2 EP, GC-LB Spray White Lube Multi-Purpose Lube NLGI Gr
MAINTENANCE SCHEDULES CONTENTS m Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 226 m Regular Check-Ups . . . . . . . . . . . . . . . . . . . . . 231 M A I N T E N A N C E S m Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226 ▫ Additional Periodic Maintenance . . . . . . . . . . 232 C m Emission Control System Maintenance . . . . . . 227 m Special Maintenance Requirements . . . . . . . . . 233 E m Maintenance Schedules . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E S C H E D U L E S 8 226 MAINTENANCE SCHEDULES INTRODUCTION This is intended as a guide to the service requirements of your vehicle. It contains all necessary instructions concerning service intervals and operations which have to be carried out. Scope and frequency of maintenance work primarily depend on the vehicle’s operating conditions. In the interest of maintaining the vehicle’s operating safety, the specified work should be performed regularly and in good time.
MAINTENANCE SCHEDULES 227 M to be serviced and adjusted in accordance with special instructions and using special measuring equipment. Modifications to or interference with the emissions control systems are not permissible. may be performed by any automotive repair establishment or individual using any automotive part which has been certified pursuant to U.S. EPA or, in the State of California, California Air Resources Board regulations.
M A I N T E N A N C E S C H E D U L E S 8 228 MAINTENANCE SCHEDULES Additional Periodic Maintenance items should also be performed beyond the items listed in the following charts to assure the optimum performance of your Crossfire.
MAINTENANCE SCHEDULES • Replace dust filter • Lubricate hood hinges, latch, and secondary latch • Reset FSS Display Function Check • Horn, hazard warning flashers, turn signals, and indicator lamps • Headlamps and exterior lighting • Windshield wipers and washer system • Check seat belts for damage and proper function • Test hydraulic brakes and check parking brake function Inspection 229 M A I N T E N • Check condition of front axle ball joints and rubber A N boots C • Check condition of steering compon
M A I N T E N A N C E S C H E D U L E S 8 230 MAINTENANCE SCHEDULES • Hydraulic brake system − Driving in dusty conditions. • Power steering system − Short trips of less than 10 miles (16 km). • Windshield washer system − More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C). FSS SYSTEM The Flexible Service System (FSS) permits a flexible service schedule that is directly related to the operating conditions of the vehicle.
MAINTENANCE SCHEDULES 231 M Depending on operating conditions throughout the year, a clock symbol may appear next to the service symbol. When this occurs, the next service is calculated and displayed in days remaining before the next service is required. REGULAR CHECK-UPS To maintain the safe operation of your vehicle, it is recommended that you perform the following tasks on a regular basis (i.e., weekly or whenever the vehicle is refueled).
M A I N T E N A N C E S C H E D U L E S 8 232 MAINTENANCE SCHEDULES • Check the windshield washer solvent and add if required. • Inspect wiper blade condition. • Check operation of lighting systems. • Inspect tires for unusual wear, damage, and pressure (at least every 14 days). • Mechanical assemblies (e.g., engine, transmission, etc.) - check for leaks. Once a Month • Inspect the battery and clean and tighten the terminals as required.
MAINTENANCE SCHEDULES At approximately every 60,000 miles (96,000 km) or 4 years: • Replace fuel filter. • Replace air cleaner filter element. At approximately 80,000 miles (129,000 km): • Change the automatic transmission fluid and filter. After this change it is filled for life. The manual transmission comes filled for life from the factory. At approximately every 100,000 miles (161,000 km) or 5 years: • Replace spark plugs.
M A I N T E N A N C E 234 MAINTENANCE SCHEDULES Dust Filter for Heating/Ventilation Replacement The dust filter is replaced during routine maintenance service. The filter element must be replaced with “B” Schedule service or every 18,500 miles (30,000 km) to maintain effectiveness. However, if operating conditions are dusty, these filters should be replaced more frequently. A cover in the HVAC unit that can be reached S from the passenger foot well provides access to the filter C element.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236 ▫ Prepare For The Appointment . . . . . . . . . . . . 236 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 236 m Reporting Safety Defects . . . . . . . . . . . . . . . . . 240 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 240 m Publication Order Forms . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty; discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a valuable clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the DaimlerChrysler Corporation’s Customer Center.
IF YOU NEED CONSUMER ASSISTANCE conventional teletypewriter (TTY) in the United States can communicate with the DaimlerChrysler Corporation by dialing 1-800-380-CHRY. Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unexpected repairs after your DaimlerChrysler Corporation’s new vehicle limited warranty expires. The DaimlerChrysler Corporation stands behind only the DaimlerChrysler Corporation’s Service Contracts.
IF YOU NEED CONSUMER ASSISTANCE 239 WARRANTY INFORMATION See your DaimlerChrysler Corporation Warranty Information Booklet for more information on warranty coverage and transfer of warranty.
IF YOU NEED CONSUMER ASSISTANCE MOPART PARTS Mopart fluids, lubricants, parts, and accessories are available from your authorized dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 states of the United States and Washington, D.C.
IF YOU NEED CONSUMER ASSISTANCE • Service Manuals. These comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing and repairing DaimlerChrysler Corporation vehicles. A complete working knowledge of the vehicle, system and/or components is written in straightforward language with illustrations, diagrams and charts. • Owner’s Manuals.
IF YOU NEED CONSUMER ASSISTANCE (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.
INDEX 10
INDEX ABS (Anti-Lock Brake) System . . . . . . . . . . . . . . 93 Adding Engine Coolant (Antifreeze) . . . . . . . . . 195 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 152 Aiming Headlights . . . . . . . . . . . . . . . . . . . . . . 215 Air Cleaner, Engine . . . . . . . . . . . . . . . . . . . . . 185 Air Conditioning . . . . . . . . . . . . . . . . . . . . 110,188 Air Conditioning Filter . . . . . . . . . . . . . . . . . . . 234 Air Conditioning Refrigerant . . . . . . . . . . . .
INDEX Carbon Monoxide Warning . . . . . . . . . . . . . . . . 44 Cargo Compartment Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 Catalytic Converter . . . . . . . . . . . . . . . . . . . . . 185 CD Player . . . . . . . . . . . . . . . . . . . . . . . . . 101,106 Chains, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . 160 Charging System Light . . . . . . . . . . . . . . . . . . . 94 Checks, Safety . . . . . .
INDEX Driving On Slippery Surfaces . . . . . . . . . . . . . . . . . . 169 Electronic Speed Control . . . . . . . . . . . . . . . . . . 77 Electronic Stability Program . . . . . . . . . . . . . . . . 74 Emergency, In Case of Hazard Warning Flasher . . . . . . . . . . . . . . . . 158 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . 167 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . 158 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Gear Ratios . . . . . . . . . . . . . . . . . . . . . . . . . . . 218 Glass Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . 205 Glove Compartment . . . . . . . . . . . . . . . . . . . . . 53 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 158 Headlights Aiming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204 Dimmer Switch . . . . . . . . . . . . . . . . . . . . . . . 65 Heater . . . . . . . . . . .
INDEX Fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Hazard Warning Flasher . . . . . . . . . . . . . . . . 158 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . 61 Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . 60,212 License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 Lights On Reminder . . . . . . . . . . . . . . . . . . . . 62 Malfunction Indicator . . . . . . .
INDEX Materials Added to . . . . . Recommendation . . . . . . Oil Filter, Selection . . . . . . . Onboard Diagnostic System Overheating, Engine . . . . . . Owner’s Manual . . . . . . . . . . . . . . . . . . . . . . . 184 . . . . . . . . . . . . . . . 184 . . . . . . . . . . . . . . . 184 . . . . . . . . . . . . 178,179 . . . . . . . . . . . . . . . 158 . . . . . . . . . . . . . . . 240 Paint Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 Parking Brake . . . . . . . . . . . . . . . . . .
INDEX Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 205 Operating Instructions . . . . . . . . . . . . . . . . . . 22 Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204 Service Assistance . . . . . . . . . . . . . . . . . . . . . . 236 Service Contract . . . .
INDEX Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 144 Spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 Tread Wear Indicators . . . . . . . . . . . . . . . . . . 145 Tow-Away Alarm . . . . . . . . . . . . . . . . . . . . . 17,174 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 Disabled Vehicle . . . . . . . . . . . . . . . . . . . . . . 170 Trailering . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 Towing Eyes . . . . . . . . . . . . .