TABLE OF CONTENTS SECTION PAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1 1 INTRODUCTION 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4 UNDERSTANDING YOUR INSTRUMENT PANEL 5 STARTING AND OPERATING 6 WHAT TO DO IN EMERGENCIES 7 MAINTAINING YOUR VEHICLE 8 MAINTENANCE SCHEDULES 9 IF YOU NEED CONSUMER ASSISTANCE 10 INDEX . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS m Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m Vehicle Identification Number . . . . . . . . . . . . . . . 6 m How To Use This Manual . . . . . . . . . . . . . . . . . . 4 m Vehicle Modifications / Alterations . . . . . . . . . . . 7 m Warnings And Cautions . . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER Vehicle Identification Number (VIN) is found on the driver’s front corner of the instrument panel, visible through the windshield.
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS 1 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . . .12 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .12 ▫ Locking Doors With The Key . . . . . . . . . . . . . .14 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .14 m Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 ▫ Replacement Keys . . . . . . . . . . . . . . . . . . . . . .16 ▫ Sentry Key Programming . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ “Child-Protection” Door Lock System (Rear Doors) . . . . . . . . . . . . . . . . . . . . . . . . . .21 m Remote Keyless Entry — If Equipped . . . . . . . . .22 ▫ To Unlock The Doors And Liftgate . . . . . . . . . .22 ▫ To Lock The Doors . . . . . . . . . . . . . . . . . . . . .23 ▫ Horn Chirp Feature . . . . . . . . . . . . . . . . . . . . .23 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .23 ▫ To Program Transmitters . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Driver And Front Passenger Supplemental Restraint System (SRS) - Airbag . . . . . . . . . . . .41 ▫ Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .50 m Engine Break-In Recommendations . . . . . . . . . . .59 m Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 11 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . .59 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place. The double sided keys may be inserted into the locks with either side up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If you try to remove the key before you place the lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector lever. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle. Locking Doors With The Key You can insert the key with either side up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE chip (transponder) embedded into them. Only keys that have been programmed to the vehicle can be used to start and operate the vehicle. The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regardless of whether or not the vehicle is locked or unlocked.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE All of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle. At the time of purchase, the original owner is provided with a four digit PIN number. This number is required for dealer replacement of keys.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed. Repeat this procedure to program up to a total of 8 keys. If you do not have a programmed sentry key, contact your dealer for details.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If you turned the wheel to the right to engage the lock, you must turn the wheel slightly to the right to disengage it. If you turned the wheel to the left to engage the lock, turn the wheel slightly to the left to disengage it. Automatic Transaxle Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK and the shift knob push-button is out.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death. CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Central Locking/Unlocking — If Equipped All vehicle doors and liftgate are locked with the first turn of the key to the LOCK position. The double unlock activation feature requires you to turn the key in the cylinder lock two times within five seconds to UNLOCK all vehicle doors and liftgate at once. You may turn this feature off and unlock all the doors and liftgate with one turn of the key by following these instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Cycle the ignition switch ON/OFF four times ending in the OFF position. 3. Press the interior door lock switch to the LOCK position. 4. A single chime will sound to signify that you have successfully completed the programming. You can turn the feature back on by repeating the above mentioned procedure.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: For emergency exit with the system engaged, move the lock plunger up (unlocked position), roll down window and open the door with the outside door handle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: You may turn off this feature and unlock all doors with one press of the button by following the procedure shown in the Central Locking/Unlocking paragraph. To Lock The Doors: Press and release the LOCK button to lock all doors and liftgate. The park lights will flash and the horn will chirp to acknowledge the signal. Horn Chirp Feature The horn chirp that signals that the doors have been locked can be turned on or off by using the following procedure: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Program Transmitters Up to four transmitters can be programmed to your vehicle. Your new vehicle was shipped with two transmitters. See your dealer for additional transmitters Additional transmitters can be programmed to the system by using the following procedure: 1. Insert the key into the ignition switch and turn the switch to the ON position. 2. Press and hold the Unlock button on the transmitter between four and ten seconds. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Transmitter Battery Service The recommended replacement battery is 2016 or its equivalent. 2 NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. 1. With the transmitter buttons facing down, use a thin coin to pry the two halves of the transmitter apart. Make sure not to damage the rubber gasket during removal. 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SECURITY ALARM SYSTEM — IF EQUIPPED The system monitors the doors, liftgate, and ignition switch for unauthorized operation. If something triggers the alarm, the system will signal for about 18 minutes. For the first 3 minutes the horn will sound and the headlights, park lights, tail lights and the indicator light in the cluster will flash. Then the exterior lights will flash for another 15 minutes.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To disarm the system: Unlock a front door/liftgate using either the key or the Keyless Entry Transmitter. Starting the vehicle with a valid Sentry key will disarm the system. A valid key is one that is programmed to that particular vehicle. A valid key will disarm the system, an invalid key will trigger the alarm. Tamper Alert If the horn sounds 3 times when you unlock a front door using either a key or the Keyless Entry Transmitter, the alarm has been activated.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LIFTGATE NOTE: The key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate. To open the liftgate, insert the key into the lock and turn to the left. The liftgate can also be unlocked using the remote keyless entry or by activating the power door lock switches located on the front doors. The central locking/ unlocking feature (if equipped) can also be activated from the liftgate key cylinder.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE EMERGENCY SEAT BACK RELEASE WARNING! 29 position 1 (Top) or position 2 (Middle), the left side rear seat back can be unlatched by pulling down on the glow-in-the-dark lever attached to the left rear seat back latching mechanism. Do not allow children to have access to the liftgate area with the rear shelf panel in position 1 (Top) or position 2 (Middle), either by climbing into the liftgate from outside, or through the inside of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Make sure that the elastic loop is around the emergency release handle at all times. If the handle is pulled downward, entirely through the elastic loop, the handle will not return to its original position and the seat back may not operate properly. POWER WINDOWS The power window switches are located on the instrument panel above the A/C controls.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. Auto Down Feature The driver’s and passenger’s front window switches have an auto down feature. Press the window switch past the detent, release, and the window will go down automatically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is very dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your dealer and have it fixed. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Rear Center Lap/Shoulder Belt Retractor Lock-Out This feature is designed to lock the retractor whenever the rear seat back is not fully latched. This prevents someone from wearing the rear center lap/shoulder belt when the rear seat back is not fully latched. NOTE: • If the rear center lap/shoulder belt can not be pulled out, check that the rear seat back is fully latched.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seats, and their covers are also labeled SRS AIRBAG. NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants in rear facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag. An airbag deployment can cause severe injury or death to infants in that position. Children that are not big enough to properly wear the vehicle seat belt (see Section on Child Restraints) should be secured in the rear seat in child restraints or beltpositioning booster seats.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during front airbag deployment could cause serious injury. Airbags need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Side Airbag in the passenger’s seat • Airbag Control Module (shared with the front airbag system) • Side impact sensors • Interconnecting Wiring How The Airbag System Works • The front airbag control module determines if a frontal impact is severe enough to require the airbags to inflate. The front control module will not detect side, roll over, or rear collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • When the front airbag control module detects a collision requiring the front airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the front airbags. The front airbag covers separate and fold out of the way as the front airbags inflate to their full size. The front airbags fully inflate in about 50 milliseconds. This is only about half of the time it takes you to blink your eyes.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE injure you if you are not seated properly, or if items are positioned in the area where the side airbag inflates. This especially applies to children. If A Deployment Occurs The airbag systems are designed to deploy when the airbag control modules detect a moderate-to-severe collision, to help restrain the driver and front passenger, and then immediately deflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags and seat belt pretensioners will not be in place to protect you. WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags and seat belt pretensioners replaced by an authorized dealer as soon as possible.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately. Child Restraint Everyone in your vehicle needs to be buckled up at all times — babies and children, too.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. • Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward facing child restraint should only be used in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the seat belt has a switchable retractor, it will have a distinctive label. • In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle end of the belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Lower Anchors and Tether for CHildren (LATCH) Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tether for CHildren. The LATCH system provides for the installation of the child restraint without using the vehicle seat belt. All three rear seating positions have exclusive lower anchorages located at the rear of the seat cushion.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchorages will continue to have features for installation in vehicles using the lap or lap/shoulder belt. They will also have tether straps, and you are urged to take advantage of all of the available attachments provided with your child restraint in any vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 In general, you will first loosen the adjusters on the lower and tether straps so that you can more easily attach the hook or connector to the lower and tether anchorages. The tether strap should be routed under the center of the head restraint and attached to the tether anchor on the rear of the seat back. Then tighten all three straps as you push the child restraint rearward and downward into the seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a child restraint top tether strap. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration, within the limits of local traffic laws, contributes to a good break-in. Wide open throttle acceleration in low gear can be detrimental and should be avoided.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. WARNING! If you are required to drive with the deck lid/liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect tread and sidewall for cuts or cracks. Check wheel nuts for tightness, and tires (including spare) for proper pressure. Lights Have someone observe the operation of exterior lights while you work the controls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 m Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .67 ▫ Phone Call Features . . . . . . . . . . . . . . . . . . . .76 ▫ Outside Mirror—Driver’s Side . . . . . . . . . . . . .67 ▫ Advanced Phone Connectivity . . . . . . . . . . . . .78 ▫ Outside Mirror—Passenger’s Side . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Folding Front Passenger Seat — If Equipped . . .84 ▫ Daytime Running Lights (Canada Only) . . . . . .96 ▫ Adjustable Head Restraints . . . . . . . . . . . . . . .85 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . .96 ▫ Heated Seats — If Equipped . . . . . . . . . . . . . .85 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . .97 ▫ Folding Rear Seat . . . . . . . . . . . . . . . . . . . . . .86 ▫ Turn Signals . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65 m Electronic Speed Control — If Equipped . . . . . . 101 ▫ Outside Temperature . . . . . . . . . . . . . . . . . . . 107 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . . 102 m Power Sunroof — If Equipped . . . . . . . . . . . . . 108 ▫ To Set At A Desired Speed . . . . . . . . . . . . . . . 102 ▫ Express Open Feature . . . . . . . . . . . . . . . . . . 108 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Position 2 (Middle) . . . . . . . . . . . . . . . . . . . . 116 ▫ Position 5 (Table) . . . . . . . . . . . . . . . . . . . . . 117 ▫ Position 3 (Floor) . . . . . . . . . . . . . . . . . . . . . 116 m Roof Luggage Rack — If Equipped . . . . . . . . . . 119 ▫ Position 4 (Vertical) . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustment. 3 Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror—Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle. WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Select a mirror and press one of the four arrows for the direction you want the mirror to move. 69 Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on the sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights turn on automatically. Closing the mirror cover turns off the lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sun Visor Sliding Feature The sun visors may be pulled out to provide extended coverage of the side glass. HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in-vehicle communications system. UConnect™; allows you to dial your cellular phone using simple voice commands (e.g., “Call Mike Work” or “Dial 248-555-1212”).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The rearview mirror contains the microphone for the system and the control buttons that will enable you to access the system. The diagram below shows the mirror with the appropriate buttons. Individual button behavior is discussed in the “Operation” Section. 71 The UConnect™ system can be used with any Hands Free Profile certified Bluetooth™ cellular phone. If your cellular phone has a different profile (i.e.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Operation Voice commands can be used in the operation of the UConnect™ system and to navigate through the UConnect™ menu structure. Voice commands should be given after each UConnect™ system prompt. You will be prompted for a specific command and then guided through the available options. There are two ways to give commands to the UConnect™ system: • You can say 9Dial9 at the 9Ready9 prompt.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For identification purposes, you will be prompted to give the UConnect™ system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between 1 and 7, 1 having the highest priority.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Add Names to Your UConnect™ Phonebook • Press the “Phone” button to begin. • After the 9Ready9 prompt, say 9Phonebook New Entry9. • When prompted, say the name of the new entry. • Next, enter the number designation (e.g. “Home”, “Work”, “Mobile”, or “Pager”). This will allow you to have multiple numbers for each phonebook entry.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phonebook edit can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mobile and a home number, but you can add John Doe’s work number later through phonebook edit. Delete Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the 9Ready9 prompt, say 9Phonebook Delete9.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnect™ system will play the names of all the phonebook entries. • To call one of the names in the list, press the ’Voice Recognition’ button during the playing of the desired name and say 9Call9. • The UConnect™ system will then prompt you as to number designation you wish to call. • The selected number will be dialed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Making a Second Call while Current Call in Progress To make a second call while you are currently in a call, press the ’Voice Recognition’ button and say 9Dial9 or 9Call9 followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone Redial Delete Paired Cellular Phones • Press the ’Phone’ button to begin. • Press the ’Phone’ button to begin. • After the 9Ready9 prompt, say 9Redial9. • After the 9Ready9 prompt, say 9Setup Phone Pairing9. • The UConnect™ system will call the last number that was dialed on your cellular phone. This may not be the last number dialed by your UConnect™ system. • At the next prompt, say 9Delete9.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you would like to connect or disconnect the Bluetooth™ connection between a paired cellular phone and the UConnect™ system, follow the instruction described in your cellular phone user’s manual. List Paired Cellular Phone Names • Press the ’Phone’ button to begin. • After the 9Ready9 prompt, say 9Setup List Phones9 and the UConnect™ system will play the phone names of all paired cellular phones in order from highest priority to lowest priority.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE pin. This method can also be used in instances where you are pressing a number on your keypad to navigate through a menu structure or to enter a number for a pager. Barge In - Overriding Prompts The ’Voice Recognition’ button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Low Signal, Battery Strength, and Roam Notification The UConnect™ system will provide notification to inform you if your cellular phone is in roaming status, has low signal strength, or has a low battery when you are trying to place a phone call. Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Towing Assistance If you need towing assistance, say 9Dial Towing Assistance9 or 9Call Towing Assistance9. Please refer to the 24-Hour Towing Assistance coverage details in the DaimlerChrysler Motors Company 24-Hour Towing Assistance Program Guide. SEATS Front Seat Adjustment The adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Bucket Seats The recliner control is on the outboard side of the seat. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position. Folding Front Passenger Seat — If Equipped The passenger front seat may be folded fully forward to provide additional cargo space.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the head restraints so that the upper edge is as high as practical. To raise the head restraint, pull up on the head restraint. To lower the head restraint, depress the button and push down on the head restraint. 85 Heated Seats — If Equipped This feature heats the front driver’s and passenger’s seats.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the switch once to select a heat setting (high or low) and press the switch a second time in the same direction to turn the heated seat off. NOTE: Once a heat setting is selected, heat will be felt within 2 to 3 minutes. Folding Rear Seat To provide additional storage area, each rear seatback can be folded forward. Push and hold the buttons shown in the picture to fold down either or both seatbacks.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts • Be sure that everyone in your vehicle is in a seat and using a seat belt properly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tumbling Rear Seat To provide additional storage in the cargo area, each rear seat can be tumbled forward. CAUTION! It is important that the front seats be pulled forward to the midpoint of the seat track to avoid contact between the rear seat and the front seatback. If the front seat is not pulled forward the two seats will make contact during the tumbling motion and cause damage to the rear seat material.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 • Pull the release lever located on the outboard side of the seat. Lift up the seat and tumble the seat forward. 3 • Attach the elastic strap, located at the base of the seat cushion, onto the hook bar on the center trim panel to hold the seat in place. To return the rear seat to it’s upright latched position, rotate the seat cushion rearward to latch the seat. Then lift the seatback to its upright latched position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Seat Removal The rear seats can be removed to provide more cargo space. • Push and hold the button on the seatback and fold down the rear seatback. • Pull the release lever located on the outboard side of the seat. Lift up the seat and tumble the seat forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Lift up the release levers to disengage the seat from the floor attachments. 91 NOTE: Small rollers on the bottom of the folded seat and a handle at the top allow the seat to be easily moved when removed from the vehicle. To reinstall the rear seat, insert the seat into the floor attachments. Lower the release levers of the seat to latch the front floor attachments and rotate the seat rearward to latch the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Use the hood prop rod clipped to the driver’s side of the engine compartment to secure the hood in the open position. Place the hood prop at the location stamped into the inner hood surface. To prevent possible damage, do not slam the hood to close it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 LIGHTS Overhead Console Map/Reading Lights — If Equipped These lights are mounted between the sun visors in the overhead console. Each light is turned ON by pressing the lens. Press the lens a second time to turn the light OFF. The lights also come on when a door is opened or the dimmer control is turned fully upward, past the second detent.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights The interior lights come on when a door is opened. With the ignition key in the OFF position, the interior lights will automatically turn off in about 8 minutes if a door is left open or the dimmer control is left in the Dome light position. Turn the ignition switch ON to restore the interior light operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior light Defeat (OFF) Rotate the dimmer control to the extreme bottom “OFF” position. The interior lights will remain off when the doors are open. Parade Mode (Daytime Brightness Feature) Rotate the dimmer control to the first detent (white semi-circle). This feature brightens the odometer and radio display when the parking lights or headlights are on during daylight conditions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights, Parking Lights, Instrument Panel Lights Turn the end of the Multi-Function Control Lever to the first detent for parking light operation. Turn to the second detent for headlight operation. To change the brightness of the instrument panel lights, rotate the center portion of the Multi-Function Control Lever up or down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Fog Lights — If Equipped The front fog light switch is on the Multi-Function Control Lever. To activate the front fog lights, turn on the parking lights or the low beam headlights and pull out the end of the control lever. If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch on the control lever. The lever is located on the right side of the steering column. Move the control lever up to select the desired wiper speed. Windshield Washers To use the washer, pull the control lever toward you and hold while spray is desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, push down on the lever below the multi-function control lever and move the steering wheel up or down, as desired. Pull the lever back up to lock the column firmly in place. WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 NOTE: The Traction Control System will make buzzing or clicking sounds when the system is in operation. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 25 mph (40 km/h). The speed control lever is located on the right side of the steering wheel. To turn the system back ON, press the switch a second time until the TRAC OFF indicator turns OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate: Push the ON/OFF button. The CRUISE indicator in the instrument cluster will illuminate. To turn the system OFF, push the ON/OFF button a second time. The CRUISE indicator will turn off. The system should be turned OFF when not in use. To Set At A Desired Speed: When the vehicle has reached the desired speed, press down on the lever and release. Release the accelerator and the vehicle will operate at the selected speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Resume Speed: To resume a previously set speed, push the “ACC/RES” lever up and release. Resume can be used at any speed above 20 mph (32 km/h). To Vary The Speed Setting: When the speed control is ON, speed can be increased by pushing up and holding “ACC/RES”. Release the lever when the desired speed is reached, and the new speed will be set. Tapping “ACC/RES” once will result in a 2 mph (3 km/h) speed increase.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing: Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Speed Control On Hills NOTE: The speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. Vehicles equipped with four speed automatic transaxles may experience a downshift to 3rd gear while climbing uphill or descending downhill.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass/Temperature Display This display provides the outside temperature and one of eight compass readings to indicate the direction the vehicle is facing. 105 STEP Button Functions: 3 WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible personal injury or property damage. 1. US 2. Metric 3. Off 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Compass Calibration The automatic calibrating feature of the compass eliminates the need to calibrate the compass due to normal varying conditions. Compass Variance Selection Variance is the difference between magnetic North and geographic North. For proper compass function, the correct variance zone must be set. Refer to the variance map for the correct variance zone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Compass Calibration If the compass appears erratic, inaccurate, abnormal or the vehicle is new, you may calibrate the compass. Prior to calibrating the compass make sure the proper zone is selected. Refer to “Magnetic Zone Selection”.Find an open area away from large metal objects. With the vehicle running, press and hold the STEP button for (about 10 to 15 seconds). The display will illuminate the CAL indicator.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The power sunroof control is located between the sun visors on the overhead console. Press and hold the button in the center of the sunroof switch to open the vent. The sunroof can be stopped at any position between closed and full vent. To close the sunroof from the vent position, press and hold the switch forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The sunshade can be opened manually. It will also open as the sunroof opens. The sunshade cannot be closed if the sunroof is open. WARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. ELECTRICAL POWER OUTLETS The outlets include tethered caps, labeled with a key symbol or battery symbol, indicating power source.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE There are two optional power outlets. One is in the Accessory Switch Bank, in the center of the instrument panel. 111 The second is in the right rear cargo area. 3 This outlet is powered directly by the battery, regardless of the ignition switch position. All accessories connected to this outlet should be removed or turned off when the vehicle is not in use, to protect the battery against discharge.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e. coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 CAUTION! • Many accessories that can be plugged into the 12 volt power outlet, draw power from the vehicle’s battery, even when not in use; i.e. cellular phones, etc. Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power such as coolers, vacuum cleaners, lights, etc., will discharge the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE Front Seat Storage Bin — If Equipped Storage Pockets There are also Storage pockets located on each door trim panel. REAR SHELF PANEL The rear shelf panel attaches to guides in the rear cargo area. The rear shelf panel may be installed in one of five different positions. NOTE: The liftgate may be opened or closed with the rear cargo shelf panel in position 1, position 2, position 3 or position 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 WARNING! • To avoid tipping, lock the shelf securely in all positions. • Do not drive this vehicle with the liftgate open, or use the shelf as a seat. 3 • Failure to follow these warnings could result in serious or fatal injury. Position 1 (Top) Insert the front outboard corners of the shelf panel into the top guides and slide forward. Press down on the back of the shelf panel to lock it into place.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Position 2 (Middle) Insert the front outboard corners of the shelf panel into the middle guides and slide forward. Press down on the back of the shelf panel to lock it into place. WARNING! Do not load objects over 100 lbs (45 kg) in position 2 (middle). Failure to follow this warning could cause the shelf to collapse resulting in personal injury. Position 3 (Floor) Insert the front outboard corners of the shelf panel into the bottom guides and slide forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Position 4 (Vertical) Insert the front outboard corners of the shelf panel into the vertical guides behind the rear seatbacks near the floor and slide downward. Push the shelf panel forward to lock it into place. 117 WARNING! When in the vertical position, the rear shelf panel should not be used as a barrier for large objects in the cargo area when the seatbacks folded down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Twist the knob on the underside of the panel and lower the shelf leg. WARNING! 3. Install the shelf leg into the liftgate latch area as labeled on the rear scuff plate. Do not load objects over 100 lbs (45 kg) in position 5 (table). Failure to follow this warning could cause the shelf to collapse resulting in personal injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Use both adjustable crossbars assemblies to support the load and distribute the load as evenly as possible.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately. Long loads which extend over the windshield, such as wood panels or surfboards, should be secured to both the front and rear of the vehicle. Cargo must be securely tied before driving your vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS m Instrument Panel Features . . . . . . . . . . . . . . . . . 125 ▫ Two Types Of Signals . . . . . . . . . . . . . . . . . . 136 m Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 126 ▫ Electrical Disturbances . . . . . . . . . . . . . . . . . . 137 m Instrument Cluster—Turbo, With AutoStick . . . . 127 ▫ AM Reception . . . . . . . . . . . . . . . . . . . . . . . 137 m Instrument Cluster—Turbo, Without AutoStick . . 128 ▫ FM Reception . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 ▫ Tape Eject . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 ▫ PTY (Program Type) Button . . . . . . . . . . . . . . 139 ▫ Scan Button . . . . . . . . . . . . . . . . . . . . . . . . . 143 ▫ Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 ▫ Changing Tape Direction . . . . . . . . . . . . . . . . 143 ▫ Fade . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 123 ▫ Tape CD Button . . . . . . . . . . . . . . . . . . . . . . 146 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 154 ▫ Time Button . . . . . . . . . . . . . . . . . . . . . . . . . 146 ▫ CD Player Operation . . . . . . . . . . . . . . . . . . . 157 ▫ Scan Button . . . . . . . . . . . . . . . . . . . . . . . . . 146 m Sales Code RB1—AM/FM Stereo Radio With DVD/GPS Navigation System . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Using The PTY (Program Type) Button (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . . 164 ▫ PTY Button 9Scan9 . . . . . . . . . . . . . . . . . . . . . 164 ▫ PTY Button 9Seek9 . . . . . . . . . . . . . . . . . . . . . 164 ▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . . 164 ▫ Reception Quality . . . . . . . . . . . . . . . . . . . . . 164 m Cassette Tape And Player Maintenance . . . . . . . 165 m CD/DVD Disc Maintenance . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 125 INSTRUMENT PANEL FEATURES 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER
UNDERSTANDING YOUR INSTRUMENT PANEL 127 INSTRUMENT CLUSTER—TURBO, WITH AUTOSTICK 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER—TURBO, WITHOUT AUTOSTICK
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Charging System Light This light shows the status of the electrical charging system. The light should come on briefly when the ignition is first turned ON and remain on briefly as a bulb check. If the light stays on or comes on while driving, it means that there is a problem with the charging system.
UNDERSTANDING YOUR INSTRUMENT PANEL 6. Engine Temperature Warning Light This light warns of an overheated engine condition. If the engine is critically hot, a warning chime will sound 10 times. After the chime turns off, the engine will still be critically hot until the light goes out. 7. Turn Signal Indicators The arrows will flash in unison with the exterior turn signal, when using the turn signal lever. NOTE: Turn signal bulbs are located in the Instrument Panel. 8.
UNDERSTANDING YOUR INSTRUMENT PANEL 10. High Beam Indicator This light shows that the headlights are on high beam. Pull the turn signal lever toward the steering wheel to switch the headlights from high or low beam. 11. Tachometer The white area of the scale shows the permissible engine revolutions-per-minute (rpm x 1000) for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 12.
UNDERSTANDING YOUR INSTRUMENT PANEL 14. Brake System Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light comes on, it may indicate that the parking brake is applied, or there is a low brake fluid level. On vehicles equipped with Anti-lock brakes (ABS), it may also indicate an ABS malfunction that could lead to reduced braking performance. WARNING! Driving a vehicle with the brake light on is dangerous.
UNDERSTANDING YOUR INSTRUMENT PANEL The light will flash when the Traction Control System is controlling traction. 16. Door Ajar Indicator This vacuum fluorescent display indicator illuminates the word “DOOR”, when a door is not completely closed. If the door is open for more than 8 minutes, the light will turn off. 17. Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven. The trip odometer shows the trip distance since the last reset. U.S.
UNDERSTANDING YOUR INSTRUMENT PANEL 20. Airbag Light The light comes on and remains on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the light does not come on during starting, stays on, or comes on while driving, have the system checked by an authorized dealer. 21. Trac Off Light — If Equipped The TRAC OFF light will illuminate momentarily as a bulb check when the ignition switch is first turned ON. If the light does not come on, have the system checked.
UNDERSTANDING YOUR INSTRUMENT PANEL Certain conditions such as a loose or missing gas cap, poor fuel quality, etc. may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations the vehicle will drive normally and will not require towing.
UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC DIGITAL CLOCK RADIO GENERAL INFORMATION The clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the ON or ACC position and the time button is pressed. Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal. AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER AND CD CHANGER CONTROLS — IF EQUIPPED Power Switch, Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. The volume will be displayed and continuously updated while the button is pressed. Seek Button (Radio Mode) Press and release the Seek button to search for the next station in either the AM or FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL PTY (Program Type) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off. Pressing the PTY button within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broadcast PTY information.
UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If no station is found with the selected PTY program type, the radio will return to the last preset station.
UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received. Scan Button Pressing the SCAN button causes the tuner to search for the next station, in either AM or FM, pausing for 5 seconds at each listenable station before continuing to the next. Pressing the AM/FM button continues the search in the alternate frequency band.
UNDERSTANDING YOUR INSTRUMENT PANEL To Change From Clock To Radio Mode Press the Time button to change the display between radio frequency and time. Operating Instructions — Tape Player Insert the cassette with the exposed tape side toward the right and the mechanical action of the player will gently pull the cassette into the play position. NOTE: When subjected to extremely cold temperatures, the tape mechanism may require a few minutes to warm up for proper operation.
UNDERSTANDING YOUR INSTRUMENT PANEL Tape Eject Press the EJT Tape button and the cassette will disengage and eject from the radio. Scan Button Press this button to play 10 seconds of each selection. Press the scan button a second time to cancel the feature. Changing Tape Direction If you wish to change the direction of tape travel (side being played), press the PTY button. The lighted arrow in the display window will show the new direction.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — CD Player NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. CAUTION! This CD player will accept 4 3⁄4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. Inserting The Compact Disc The CD player contained within the radio is not a multi-disc changer, and will only accept one CD.
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Button Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. EJT CD (Eject) Button Press this button and the disc will unload and move to the entrance for easy removal. The unit will switch to the radio mode.
UNDERSTANDING YOUR INSTRUMENT PANEL MODE Press the MODE button to select between the tape player, CD player, or satellite radio (if equipped). Time Button Press this button to change the display from elapsed CD playing time to time of day. To select Satellite Radio (if equipped), press the MODE button until the word SIRIUS appears. The following will be displayed in this order: After three seconds, the current channel name and number will be displayed for five seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL Push-Button While the CD changer is playing, press the NUMBER 1 push-button or the NUMBER 5 push-button to select a disc numbered higher or lower than the one currently being played. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display. 147 CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. Seek Press and release the SEEK button to search for the next station in either the AM or FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL Tune Press the TUNE control up or down to increase or decrease the frequency. If you press and hold the button, the radio will continue to tune until you release the button. The frequency will be displayed and continuously updated while the button is pressed. Balance The Balance control adjusts the left-to-right speaker balance. Press the BAL button in and it will pop out. Adjust the balance and push the button back in.
UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice.
UNDERSTANDING YOUR INSTRUMENT PANEL Inserting The Compact Disc CAUTION! This CD player will accept 4 3⁄4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day. If the power is ON, the unit will switch from radio to CD mode and begin to play when you insert the disc.
UNDERSTANDING YOUR INSTRUMENT PANEL Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play. This feature plays the tracks on the selected disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track. Press the RND (button 4) button a second time to stop Random Play.
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display. Fast Forward And Rewind Buttons Press and hold the FF button for fast forward. Press and hold the RW button for fast reverse. The audio output can be heard when fast forward and fast reverse are activated. Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an interesting change of pace.
UNDERSTANDING YOUR INSTRUMENT PANEL Radio Display Messages Your radio has been designed to display certain messages when a problem is detected with the CD player. SALES CODE RBQ—AM/FM STEREO RADIO WITH 6 - DISC CD CHANGER Radio Operation Power/Volume Control Press the PWR/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio. Mode Press the MODE button repeatedly to select between AM, FM, the CD changer and Sirius Satellite Radio™ (if equipped). The display will show ST when a stereo station is received. To select Sirius Satellite Radio™ (if equipped), press the MODE button until the word SIRIUS appears.
UNDERSTANDING YOUR INSTRUMENT PANEL Fade The Fade control provides for balance between the front and rear speakers. Press the FADE button in and it will pop out. Adjust the balance and push the button back in. Tone Control The tone controls affect the Bass and Treble frequency bands. Each is controlled by a slider control with a detent at the mid position. Moving a control up or down increases or decreases amplification of the band. The mid position provides a balanced output.
UNDERSTANDING YOUR INSTRUMENT PANEL General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired operation. NOTE: Changes or modifications not expressively approved by the party responsible for compliance could void the user’s authority to operate the equipment.
UNDERSTANDING YOUR INSTRUMENT PANEL show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. LOAD/ EJT — Load Press the LOAD/ EJT button and the button with the corresponding number where the CD is being loaded. After the radio displays “load” insert the CD into the player. Radio display will show “loading” when it is being loaded.
UNDERSTANDING YOUR INSTRUMENT PANEL FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Random Play — SET / RND Press the RND button while the CD is playing to activate Random Play. This feature plays the tracks on the disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track. Press TUNE FF to fast forward through the tracks.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Foreign Language News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather Radio Display Language News Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R&B Sports Talk Top 40 Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY na
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RB1—AM/FM STEREO RADIO WITH DVD/GPS NAVIGATION SYSTEM 161 SATELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius™ Satellite Radio. This service offers up to 100 channels of music, sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios.
UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Serial Number/Sirius Identification Number (ENS/SID) The Electronic Serial Number/Sirius Identification Number is needed to activate your Sirius Satellite Radio system. To access the ESN/SID, refer to the following steps: ESN/SID Access With RBB and RBK Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the Tape Eject or CD Eject (depending on the radio type) and Time buttons simultaneously for 3 seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL • After 3 seconds, the current channel name and channel number will be displayed for 5 seconds. • The current program type and channel number will then be displayed for 5 seconds. • The current channel number will then be displayed until an action occurs. A CD or tape may remain in the radio while in the Satellite radio mode. Selecting a Channel Press and release the SEEK or TUNE buttons to search for the next channel.
UNDERSTANDING YOUR INSTRUMENT PANEL Using the PTY (Program Type) Button (if equipped) Follow the PTY button instructions that apply to your radio. PTY Button (SEEK( When the desired program is obtained, press the 9SEEK9 button within five seconds. The channel will change to the next channel that matches the program type selected. PTY Button (SCAN( When the desired program type is obtained, press the 9SCAN9 button within five seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 165 • Dense tree coverage may interrupt reception in the form of short audio mutes. 4. Before inserting a tape, make sure that the label is adhering flatly to the cassette. • Driving under wide bridges or along tall buildings can cause intermittent reception. 5. A loose tape should be corrected before use. To rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the required directions.
UNDERSTANDING YOUR INSTRUMENT PANEL dirty (noticeably poor sound), it may not be possible to remove all deposits with a simple WET cleaning cassette. 7. Do not store the disc where temperatures may become too high. CD/DVD DISC MAINTENANCE To keep the CD/DVD discs in good condition, take the following precautions: RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 167 Fan and Air conditioning Control Use this control to regulate the amount of air forced through the system in any mode you select. The fan speeds to the left of the OFF position are for Air Conditioning. Choosing one of these speeds turns on the air conditioning compressor. The fan speed increases as you move the control to the left from the OFF position.
UNDERSTANDING YOUR INSTRUMENT PANEL Mode Control (Air Direction) The mode control allows you to choose from several patterns of air distribution. You can select either a primary mode, as identified by the symbols, or a blend of two of these modes. The center point between modes gives an even blend of both modes. The closer the control is to a particular mode, the more air distribution you receive from that mode. Bi-Level Air is directed through the panel and floor outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL Defrost Air is directed through the windshield and side window demist outlets. Use this mode with maximum fan and temperature settings for best windshield and side window defrosting. NOTE: The air conditioning compressor operates in both Mix and Defrost or a blend of these modes even if the fan switch is not in the A/C position. This dehumidifies the air to help dry the windshield. To improve fuel economy, use these modes only when necessary.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If your air conditioning performance seems lower than expected, check the front of the A/C condenser: located in front of the radiator, for an accumulation of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser. Fabric front fascia protectors may reduce air flow to the condenser, reducing air conditioning performance.
UNDERSTANDING YOUR INSTRUMENT PANEL 171 Operating Tips 4
UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Vehicle side windows tend to fog on the inside in mild rainy or humid weather. To clear the windows, use the A/C, PANEL and blower controls. Direct the panel outlets toward the side windows. Do not use recirculate without A/C for long periods as fogging may occur.
UNDERSTANDING YOUR INSTRUMENT PANEL 173 Side Window Demisters A side window demister outlet is at each end of the instrument panel. These nonadjustable outlets direct air toward the side windows when the system is in either the FLOOR, MIX, or DEFROST mode. The air is directed at the area of the windows through which you view the outside mirrors. 4 REAR WINDOW FEATURES Electric Rear Window Defroster The push-button is located at the center of the instrument panel, below the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! To avoid damaging the electrical conductors, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the rear window. Labels can be peeled off after soaking with warm water. Rear Wiper/Washer Switch A push-button at the center of the instrument panel, below the radio, turns the rear wiper ON or OFF. When this switch is pressed the rear wiper will operate at a fixed interval of about 4 seconds between wipes.
UNDERSTANDING YOUR INSTRUMENT PANEL Adding Washer Fluid The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the rear of the engine compartment on the passenger side and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water.
STARTING AND OPERATING CONTENTS m Starting Procedures . . . . . . . . . . . . . . . . . . . . . 180 m Automatic Transaxle — If Equipped . . . . . . . . . 183 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . . 180 ▫ Brake/Transmission Interlock System . . . . . . . 184 ▫ Manual Transaxle . . . . . . . . . . . . . . . . . . . . . 180 ▫ Automatic Transaxle Ignition Interlock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 ▫ Normal Starting . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING ▫ AutoStick General Information . . . . . . . . . . . . 188 ▫ Tire Identification Number (TIN) . . . . . . . . . . 201 m Manual Transaxle Operation . . . . . . . . . . . . . . . 189 ▫ Tire Loading And Tire Pressure . . . . . . . . . . . 202 ▫ 2.4 Liter Turbo— If Equipped . . . . . . . . . . . . . 190 m Tires—General Information . . . . . . . . . . . . . . . . 206 ▫ Recommended Shift Speeds . . . . . . . . . . . . . . 190 ▫ Tire Pressure . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 179 m Tire Rotation Recommendations . . . . . . . . . . . . 215 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . . 219 m Fuel Requirements . . . . . . . . . . . . . . . . . . . . . . 216 ▫ Fuel System Cautions . . . . . . . . . . . . . . . . . . 219 ▫ 2.4L Standard Engine And 2.4L Standard Turbo Engine . . . . . . . . . . . . . . . . . . . . . . . . 216 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . . . 220 ▫ 2.4L High Output Turbo Engine . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Automatic Transaxle The gear selector must be in the NEUTRAL or PARK position before you can start the engine. Apply the brakes before shifting to any driving gear. CAUTION! NOTE: You must press the brake pedal before shifting out of Park.
STARTING AND OPERATING started within 3 seconds, slightly depress the accelerator pedal while continuing to crank. If the engine fails to start within 15 seconds, turn the ignition switch to the “OFF” position, wait 10 to 15 seconds, then repeat the normal starting procedure. WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way.
STARTING AND OPERATING CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. After Starting The idle speed will automatically decrease as the engine warms up. Turbocharger “Cool Down” NOTE: Letting the engine idle after severe operation allows the turbine housing to cool to normal operating temperature.
STARTING AND OPERATING AUTOMATIC TRANSAXLE — IF EQUIPPED CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed.
STARTING AND OPERATING Brake/Transmission Interlock System This system prevents you from moving the gear shift out of Park and into any gear unless the brake pedal is pressed. This system is active only while the ignition switch is in the ON positions. Always depress the brake pedal first, before moving the gear selector out of PARK. Four Speed Automatic Transaxle The electronically controlled transaxle provides a precise shift schedule.
STARTING AND OPERATING Turn the Key to OFF then restart the engine. Shift into D and resume driving. NOTE: Even if the transaxle can be reset, it is recommended that you visit a dealer at your earliest possible convenience. Your dealer has diagnostic equipment to determine if the problem could recur. If the transaxle cannot be reset, dealer service is required. Gear Ranges For Four Speed Automatic Transaxle DO NOT race the engine when shifting from PARK or NEUTRAL positions into another gear range.
STARTING AND OPERATING The following indicators should be used to ensure that you have engaged the transmission shift lever into the P (Park) position: “R” Reverse Shift into this range only after the vehicle has come to a complete stop. • When shifting into P (Park), depress the button on the shift lever and firmly move the lever all the way forward until it stops. “N” Neutral Engine may be started in this range.
STARTING AND OPERATING “3” Drive This range eliminates shifts into Overdrive. The transaxle will operate normally in first and second while in this range. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance, fuel economy, and extend transaxle life by reducing excessive shifting and heat build up. Use the “3” range when descending steep grades to prevent brake system distress.
STARTING AND OPERATING You can shift in or out of the autostick mode at any time without taking your foot off the accelerator pedal. If you choose the Overdrive mode, the transmission will operate automatically; shifting between the four available gears. When you wish to engage autostick, simply move the shift lever to the AUTOSTICK position. The transmission will remain in the current gear until an upshift or downshift is chosen.
STARTING AND OPERATING MANUAL TRANSAXLE OPERATION NOTE: The parking brake should be engaged and the gear selector placed in REVERSE before leaving the vehicle, especially on an incline. Fully depress the clutch pedal before you shift gears. As you release the clutch pedal, lightly depress the accelerator pedal. 189 Use each gear in numerical order - do not skip a gear. Be sure the transaxle is in FIRST gear, (not THIRD), when starting from a standing position.
STARTING AND OPERATING 2.4 Liter Turbo— If Equipped When moving the shifter lever into REVERSE press the lever to the left until the resistance is overcome. When the ignition switch is in the ON position, a chime will sound to confirm that reverse has been selected and the backup lights will illuminate. NOTE: Listen for the audible chime to confirm REVERSE gear is properly selected. Never shift into REVERSE until the vehicle has come to a complete stop.
STARTING AND OPERATING For improved performance, your manual transaxle may be upshifted up to the maximum speeds listed in table 2 (within legal speed limits). TABLE 2-MANUAL TRANSAXLE MAXIMUM PERFORMANCE SHIFT SPEEDS IN mph (km/h) ENGINE 1 to 2 2 to 3 3 to 4 4 to 5 SIZE 30 60 85 115 2.4L (48) (97) (136) (185) If you exceed these speeds, you may notice the engine cut in and out. This is caused by an electronic limiter in the engine computer. The engine will run normally when you reduce engine speed.
STARTING AND OPERATING PARKING BRAKE When the parking brake is applied with the ignition on, the Brake Light in the instrument cluster will come on. NOTE: This light only shows that the parking brake is on. It does not show the degree of brake application. If the parking brake is applied while the vehicle is moving, a chime will sound to alert the driver. The chime will sound up to 10 times or until the vehicle has returned to a stop.
STARTING AND OPERATING When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the automatic transaxle locking mechanism may make it difficult to move the selector out of Park. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on a uphill grade. You should always apply the parking brake before leaving the vehicle.
STARTING AND OPERATING BRAKE SYSTEM Your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. However, the effort required to brake the vehicle will be much greater than that required with the power system operating. WARNING! Riding the brakes can lead to brake failure and possibly an accident.
STARTING AND OPERATING During stops where ABS is activated, a vibration of the brake pedal may be felt and associated system noises may be heard. NOTE: Pumping of the brake pedal will diminish the effectiveness of Anti-lock brakes and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
STARTING AND OPERATING POWER ASSISTED STEERING The power assisted steering system of your vehicle provides mechanical steering capability in the event power assist is lost. If for some reason the hydraulic pressure is interrupted, it will still be possible to steer your vehicle. Under these conditions you will observe a substantial increase in steering effort. TRACTION CONTROL — IF EQUIPPED The Traction Control System will improve acceleration and steering on slippery surfaces by reducing tire spin.
STARTING AND OPERATING • There is a Anti-Lock Brake System malfunction; TIRE SAFETY INFORMATION • There is a Traction Control System malfunction; Tire Markings 197 • The system has been automatically deactivated to prevent damage to the brake system due to overheated brake temperatures. NOTE: Extended heavy use of Traction Control may cause the system to deactivate and turn on the TRAC OFF Light located in the instrument cluster.
STARTING AND OPERATING • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter 9P9 is absent from this tire size designation. Example: 215/65R15 96H • Temporary Spare tires are high pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
STARTING AND OPERATING 199 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards (....blank....( = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (ie. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. 201 Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: Some vehicles have a “Tire and Loading Information” placard located on the driver’s side “B” pillar. This placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires.
STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
STARTING AND OPERATING 3. Subtract the combined weight of the driver and passengers from XXX kilograms or XXX pounds. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “XXX” amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lb. (1400–750 (5 x 150) = 650 lb.) 5. Determine the combined weight of luggage and cargo being loaded on the vehicle.
STARTING AND OPERATING 205 5
STARTING AND OPERATING WARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 207 Some vehicles may have Supplemental Tire Pressure Information for vehicle loads that are less that the maximum loaded vehicle condition.
STARTING AND OPERATING The pressure should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are underinflated. CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap–if equipped.
STARTING AND OPERATING Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important.
STARTING AND OPERATING Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Always use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels). Never combine them with other types of tires. Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
STARTING AND OPERATING 211 Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 35 mph (55 km/h). Do not install more than one compact spare tire/wheel on the vehicle at any given time. See the paragraph on Freeing A Stuck Vehicle in Section 6 of this manual.
STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point.
STARTING AND OPERATING 213 WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. TIRE CHAINS Due to limited clearance, tire chains are not recommended. CAUTION! Damage to the vehicle may result if tire chains are used. SNOW TIRES Some areas of the country require the use of snow tires during winter.
STARTING AND OPERATING Tire Rotation Recommendations Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all season type tires.
STARTING AND OPERATING FUEL REQUIREMENTS 2.4L Standard Engine and 2.4L Standard Turbo Engine Your vehicle is designed to meet all emission regulations and provide excellent fuel economy when using high quality regular unleaded gasoline with an octane rating of 87. The use of premium gasoline is not recommended. The use of premium gasoline will provide no benefit over high quality regular gasolines, and in some circumstances, may result in poorer performance. 2.
STARTING AND OPERATING 217 Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifications (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available.
STARTING AND OPERATING may not be covered by the vehicle warranty. While MTBE is an oxygenate made from Methanol, it does not have the negative effects of Methanol. MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane number. Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT.
STARTING AND OPERATING CAUTION! If the Malfunction Indicator light is flashing, immediate service is required. See the paragraph on the Onboard Diagnostics System in section 7 of this manual. Materials Added to Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in additional cost. Therefore you should not have to add anything to the fuel.
STARTING AND OPERATING • The use of fuel additives which are now being sold as octane enhancers is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer and may not be covered under the New Vehicle Warranty. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
STARTING AND OPERATING ADDING FUEL The fuel tank filler tube has a restricting door about 2 inches (50 mm) inside the opening. If using a portable container, it should have a flexible nozzle long enough to force open the restricting door. Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door, on the passenger’s side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle.
STARTING AND OPERATING CAUTION! WARNING! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. • Remove the fuel tank filler tube cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury. • The volatility of some gasolines may cause a build up of pressure in the fuel tank that may increase while you drive. This pressure can result in a spray of gasoline and/or vapors when you remove the cap from a hot vehicle.
STARTING AND OPERATING NOTE: Tighten the gas cap about 1/4 turn until you hear one click. This is an indication that cap is properly tightened. If the gas cap is not tighten properly, the Malfunction Indicator Light will come on. Be sure the gas cap is tightened every time the vehicle is refueled. WARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
STARTING AND OPERATING Perform maintenance services as prescribed in the maintenance schedules manual. When your vehicle is used for trailer towing, never exceed the gross axle weight rating (GAWR) by the addition of: • The tongue weight of the trailer. • The weight of any other type of cargo or equipment put in or on your vehicle. • Remember that everything put in or on the trailer adds to the load on your vehicle.
STARTING AND OPERATING 225 WARNING! NOTE: Check the automatic transaxle fluid level before towing. Connecting trailer brakes to your vehicle’s hydraulic brake lines can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. NOTE: For vehicles equipped with Autostick. By using the Autostick modes, and selecting a specific gear range, frequent shifting can be avoided.
WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 228 m Driving On Slippery Surfaces . . . . . . . . . . . . . . 238 m If Your Engine Overheats . . . . . . . . . . . . . . . . . 228 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . . 238 m Jacking And Tire Changing . . . . . . . . . . . . . . . . 230 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER Do not use this emergency warning system when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and the vehicle locked. NOTE: With extended use, the flasher may wear down your battery.
WHAT TO DO IN EMERGENCIES If the pointer rises to the H (red) mark, the instrument cluster will sound a chime. Pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the H (red) mark, turn the engine off immediately and call for service. NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off.
WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, refer to Section 7, Maintenance, of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous.
WHAT TO DO IN EMERGENCIES Jack Location The jack and jack-handle are stowed behind the right rear side trim panel in the cargo area. 231 Spare Tire Stowage The compact spare tire is stowed under the rear of the vehicle by means of a hook/basket mechanism. To remove or stow the compact spare, use the jack handle to rotate the “spare tire drive” nut. The nut is located under the rear scuff plate at the right rear of the cargo area, just inside the liftgate opening.
WHAT TO DO IN EMERGENCIES Spare Tire Removal Lift up the cover and fit the jack-handle over the drive nut. Rotate the nut to the left until you can remove the swivel hook from the stowage basket. Swing the basket down to remove the compact spare tire. CAUTION! The hook is designed for use with the jack handle only. Use of an air wrench or other power tools is not recommended and can damage the winch.
WHAT TO DO IN EMERGENCIES Jacking Instructions 1. Remove the scissors jack and lug wrench from the stowage bag. NOTE: If equipped with a center cap that covers the wheel nuts, pry off the cap using the small end of the lug wrench. To reinstall the cap, make sure it is properly lined up before pushing it on to the wheel. 2. Loosen, but do not remove, the wheel nuts by turning them to the left one turn while the wheel is still on the ground.
WHAT TO DO IN EMERGENCIES Do not raise the vehicle until you are sure the jack is securely engaged. 4. Raise the vehicle by turning the jack screw to the right, using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it.
WHAT TO DO IN EMERGENCIES 100 ft. lbs (135 N·m). If you doubt that you have tightened the nuts correctly, have them checked with a torque wrench by your dealer or at a service station. 8. Remove the wheel blocks and lower the jack until it is free. Stow the lug wrench, and jack in their designated location. Secure all parts using the means provided. WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle.
WHAT TO DO IN EMERGENCIES WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from another vehicle. This type of start can be dangerous if done improperly, so follow this procedure carefully. 1.
WHAT TO DO IN EMERGENCIES 237 WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush the contaminated area immediately with large quantities of water. A battery generates hydrogen gas which is flammable and explosive. Keep flame or spark away from the vent holes.
WHAT TO DO IN EMERGENCIES 7. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 8. When removing the jumper cables, reverse the sequence exactly. Be careful of the moving belts and fan. DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the front wheels to pull erratically to the right or left.
WHAT TO DO IN EMERGENCIES 2. Slow down if road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain enough distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop. 239 If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels.
WHAT TO DO IN EMERGENCIES CAUTION! Racing the engine or spinning the wheels too fast may lead to transaxle overheating and failure. It can also damage the tires. Do not spin the wheels above 35 mph (55km/h).
WHAT TO DO IN EMERGENCIES All Transaxles CAUTION! If the vehicle being towed requires steering, the ignition switch must be in the OFF position, not in the LOCK or ACCESSORY positions. Do not attempt to use sling type equipment when towing. When securing vehicle to flat bed truck, do not attach to front or rear suspension components. Damage to your vehicle may result from improper towing. If it is necessary to use the accessories while being towed (wipers, defrosters, etc.
MAINTAINING YOUR VEHICLE CONTENTS m 2.4L High Output Turbo Engine Compartment . . 246 ▫ Drive Belts — Check Condition And Tension . . 256 m 2.4L Engine Compartment . . . . . . . . . . . . . . . . 247 ▫ Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . 256 m Onboard Diagnostic System — OBD II . . . . . . . . 248 ▫ Ignition Wiring System . . . . . . . . . . . . . . . . . 256 m Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Air Conditioner . . . . . . . . . . . . . . . . . . . . . . 261 ▫ Power Steering — Fluid Check . . . . . . . . . . . . 261 ▫ Front Suspension Ball Joints . . . . . . . . . . . . . . 262 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . . 262 ▫ Windshield Wiper Blades . . . . . . . . . . . . . . . . 263 ▫ Windshield Washer Reservoir . . . . . . . . . . . . . 264 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . . 264 ▫ Cooling System . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 245 ▫ Center High Mounted Stop Light . . . . . . . . . . 289 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291 m Fluids And Capacities . . . . . . . . . . . . . . . . . . . 290 ▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292 m Recommended Fluids, Lubricants And Genuine Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 2.
MAINTAINING YOUR VEHICLE 247 2.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing.
MAINTAINING YOUR VEHICLE ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL symbol is on with the engine running. b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine.
MAINTAINING YOUR VEHICLE 251 NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. WARNING! Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance.
MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight. dipstick. Adding one quart of oil when the reading is at the MIN mark will result in a MAX reading on these engines.
MAINTAINING YOUR VEHICLE • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C). • Trailer towing. • Taxi, Police or delivery service (commercial service). • Off-Road or desert operation.
MAINTAINING YOUR VEHICLE American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils. Engine Oil Viscosity (SAE Grade) The proper SAE viscosity grade of engine oil should be selected based on the following recommendation and be within the operating temperature shown in the engine oil viscosity chart. • SAE 5W-30 engine oil is preferred.
MAINTAINING YOUR VEHICLE Synthetic Engine Oils There are a number of engine oils being promoted as either synthetic or semi-synthetic. If you chose to use such a product, use only those oils that are American Petroleum Institute (API) Certified and SAE viscosity standard. Follow the service schedule that describes your driving type. Materials Added To Engine Oils The manufacture strongly recommends against the addition of any additives (other than leak detection dyes) to the engine oil.
MAINTAINING YOUR VEHICLE Drive Belts — Check Condition and Tension At the mileage shown in the maintenance schedules, check all drive belts for condition and proper tension. Improper belt tension can cause belt slippage and failure. Inspect the drive belts for evidence of cuts, cracks, or glazing and replace them if there is any sign of damage which could result in belt failure. If adjustment is required, see your authorized dealer for service.
MAINTAINING YOUR VEHICLE 257 CAUTION! WARNING! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle.
MAINTAINING YOUR VEHICLE To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transaxle is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. accumulate deposits. If a valve is not working properly, replace it with a new valve. DO NOT ATTEMPT TO CLEAN THE OLD PCV VALVE! Check ventilation hose for indication of damage or plugging deposits. Replace if necessary.
MAINTAINING YOUR VEHICLE 259 the filter element should be inspected periodically and replaced if necessary at the intervals shown on Schedule “B”. Maintenance-Free Battery You will never have to add water, nor is periodic maintenance required. WARNING! CAUTION! The air cleaner can provide a measure of protection in the case of engine backfire. Do not remove the air cleaner unless such removal is necessary for repair or maintenance.
MAINTAINING YOUR VEHICLE WARNING! CAUTION! Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Battery gas is flammable and explosive. Keep flame or sparks away from the battery. Don’t use a booster battery or any other booster source with an output greater than 12 volts.
MAINTAINING YOUR VEHICLE Air Conditioner Check the air conditioning system at the start of the warm weather season. NOTE: If your air conditioning performance seems lower than expected, check the front of the A/C condenser for an accumulation of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser as required. Fabric front fascia protectors may reduce air flow to the condenser, reducing air conditioning performance.
MAINTAINING YOUR VEHICLE WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid types.
MAINTAINING YOUR VEHICLE Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non abrasive cleaner or use the washer solvent. This will remove accumulations of salt, waxes or road film and help reduce streaking and smearing. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield.
MAINTAINING YOUR VEHICLE Windshield Washer Reservoir The washer fluid reservoir is located in the rear of the engine compartment on the passenger side and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze). Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
MAINTAINING YOUR VEHICLE WARNING! Exhaust gases can injure or kill. They contain carbon monoxide which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. Follow the above precautions to keep your exhaust system as safe as possible. 265 Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the OFF position.
MAINTAINING YOUR VEHICLE Coolant Checks Check coolant protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of the radiator for an accumulation of bugs, leaves, etc. Clean the radiator by gently spraying water from a garden hose at the back of the core.
MAINTAINING YOUR VEHICLE Selection Of Coolant Use only the manufacturers recommended coolant, refer to Recommended Fluids, Lubricants and Genuine Parts for correct coolant type. CAUTION! Failure to use the proper antifreeze could cause radiator plugging and engine overheating. Do not mix antifreeze brands or use plain water alone or alcohol based antifreeze products.
MAINTAINING YOUR VEHICLE The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. WARNING! The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system.
MAINTAINING YOUR VEHICLE 269 humidity accumulation on the radiator and being vaporized when the thermostat opens, allowing hot water to enter the radiator. • Keep the front of the radiator clean. If your vehicle has air conditioning, keep the front of the condenser clean, also. If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not change the thermostat for summer or winter operation.
MAINTAINING YOUR VEHICLE Insure nylon tubing in these areas has not melted or collapsed Inspect all hose connections such as clamps and couplings to make sure the are secure and no leaks are present. Components should be replaced immediately if there is any evidence of degradation that could cause failure.
MAINTAINING YOUR VEHICLE brittle rubber, cracking, tears, cuts, abrasions, and excessive swelling suggest deterioration of the rubber. Particular attention should be made to examining those hose surfaces nearest to high heat sources, such as the exhaust manifold. Inspect all hose clamps and couplings to make sure they are secure and no leaks are present. Insure nylon tubing in these areas has not melted or collapsed.
MAINTAINING YOUR VEHICLE fluid reservoir. Fluid level can be expected to fall as the brake pads wear. Brake fluid level should be checked when pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. WARNING! Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident.
MAINTAINING YOUR VEHICLE Automatic Transaxle All front wheel drive vehicles have a transmission and differential assembly contained within a single housing. Selection Of Lubricant It is important that the proper lubricant is used in the transaxle to assure optimum transaxle performance. Use only manufacturers recommended transmission fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE Procedure For Checking Fluid Level To properly check the automatic transaxle fluid level, the following procedure must be used: 1. The vehicle must be on level ground. 2. The engine should be running at curb idle speed for a minimum of 60 seconds. 3. Fully apply parking brake. 4. Place the gear selector momentarily in each gear position ending with the lever in P (PARK). 5. Remove the dipstick and determine if the fluid is hot or warm.
MAINTAINING YOUR VEHICLE 275 If the fluid is cold, the fluid level should be between the lower two holes, into the area marked “LOW”. Maintenance schedule “A”—Non Turbo Charged Engines – No change necessary. If the fluid level shows low, add sufficient transmission fluid to bring to the proper level. Maintenance schedule “A”—Turbo Charged Engines – No change necessary.
MAINTAINING YOUR VEHICLE Special Additives The manufacturer recommends against the addition of any fluid additives to the transaxle. The only exception to this policy is the use of special dyes to aid in detecting fluid leaks. The use of transmission sealers should be avoided as they may adversely affect seals. Manual Transaxle Lubricant Selection Use only manufacturers recommended transmission fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle.
MAINTAINING YOUR VEHICLE CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels and rear deck lid be kept clear and open.
MAINTAINING YOUR VEHICLE CAUTION! If your vehicle is equipped with flame or woodgrain graphics, it is recommended that special care be taken when using hand-held pressure washers to clean your vehicle. The pressure of these hand-held car wash wands can vary greatly and could possibly cause damage to the surface of the graphic. Hold the tip of the wand at least 12 inches away from the graphic surface when cleaning the vehicle.
MAINTAINING YOUR VEHICLE CAUTION! Many wheel cleaners contain acids that may harm the wheel surface. NOTE: Replacement costs for components damaged as a result of not following the recommended cleaning practices are considered the responsibility of the customer. Interior Care Use Mopar Fabric Cleaner to clean fabric upholstery and carpeting. Use Mopar Vinyl Cleaner to clean vinyl upholstery and vinyl trim. Mopar Total Clean is specifically recommended for leather upholstery.
MAINTAINING YOUR VEHICLE 281 Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. cleaning inside rear windows equipped with electric defrosters. Do not use scrapers or other sharp instruments which may scratch the elements. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.
MAINTAINING YOUR VEHICLE 2. Dry with a soft tissue. FUSES Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. Underhood Fuses (Power Distribution Center) A Power Distribution Center is located in the engine compartment; next to the air cleaner filter. A label identifying the components and circuits is located on the underside of the cover.
MAINTAINING YOUR VEHICLE 283 7 Power Distribution Center Cover
MAINTAINING YOUR VEHICLE FUSE 1 2 3 4 5 6 7 8 9 10 11 12 Amp/Color Items Fused 30 Amp/Pink Ignition Start 40 Amp/Green Anti-Lock Brake (ABS) Pump 40 Amp/Green Ignition Run 30 Amp/Blue Heated Seats 40 Amp/Green Radiator Fan 20 Amp/Blue Power Height Adjuster 30 Amp/Blue Anti-Lock Brake (ABS) Solenoid 40 Amp/Green Electric Back Light (EBL) Spare 40 Amp/Green Exterior Lighting, Remote Keyless Entry, Alarm and Door Locks 10 Amp/Red Air Conditioning (A/C) 15 Amp/Lt.
MAINTAINING YOUR VEHICLE Interior Fuses The fuse access panel is on the left side of the instrument panel next to the steering column. To remove the panel, pull it out, as shown. A label identifying the components and circuits is located on the inside of the cover. 285 CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
MAINTAINING YOUR VEHICLE REPLACEMENT BULBS LIGHT BULBS — Inside Bulb No. ABS Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . LED Airbag Indicator . . . . . . . . . . . . . . . . . . . . . . . . LED Brake System Warning Indicator . . . . . . . . . . . . . LED Center Console Floor Lamp . . . . . . . . . . . . . . . . . T37 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 6233137 Console Gear Selector . . . . . . . . . . . . . . . . . . . PC194 Cruise Indicator . . . . . . . . .
MAINTAINING YOUR VEHICLE LIGHTS BULBS — Outside Bulb No. Low Beam Headlight . . . . . . . . . . . . . . . . . . . 9006XS High Beam Headlight . . . . . . . . . . . . . . . . . . . 9005XS Front Park/Turn Signal/Side Marker Light . 4157NAKX Front Fog Light . . . . . . . . . . . . . . . . . . . . . . . . . 9006 Center High Mounted Stop Light (CHMSL) . . . . . . . . . . . . . . . . . . . . . . . . . 921–W16W Rear Tail/Stop/Turn Signal Light . . . . . . 3157–P27/7W Backup Light. . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE Front Park/Turn Signal/Side Marker Lights Front Fog Lights — If Equipped 1. Remove the headlight access cover splash shield, located in the front wheel well opening. 1. Remove the fasteners attaching the lower splash shield to gain access to the fog light. 2. Rotate the socket to the left one quarter turn to replace and replace the bulb. 2. Twist and remove the bulb from the fog light housing. 3. Disconnect the electrical connector and replace bulb.
MAINTAINING YOUR VEHICLE 289 Back Up Light Bulb 1. Remove the screws attaching the back up light to the rear fascia and remove the housing. 2. Remove the socket from the housing. 3. Pull the bulb out of the socket and replace. Center High Mounted Stop Light 1. Open the liftgate and remove the liftgate CHMSL cover. 2. Remove CHMSL lens from the housing by unlatching the two side latches. 3. Pull the bulb out of the socket and replace. 3. Pull the bulb out of the socket and replace.
MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel (Approximate) Engine Oil-With Filter 2.4 Liter Engines (SAE 5W-30, API Certified Engine Oil) Cooling System * 2.4 Liter Turbocharged Engines (Mopart Antifreeze/Coolant 5 Year/100,000 Miles Formula) 2.4 Liter Non-Turbocharged Engines (Mopart Antifreeze/ Coolant 5 Year/100,000 Miles Formula) * Includes heater and coolant recovery bottle filled to MAX level. U.S. 15 Gallons Metric 56.7 Liters 5.0 qts 4.8 Liters 8.1 qts 7.7 Liters 6.5 qts 6.
MAINTAINING YOUR VEHICLE 291 RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluids, Lubricants and Genuine Parts Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) Use API Certified SAE 5W-30 Engine Oil. Refer to oil viscosity chart for correct SAE grade meeting DaimlerChrysler Material Standard MS-6395. Non Turbo—Mopar 4105409 or equiv. Turbo—Mopar 4781452AA or equiv.
MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Fluid. Manual Transmission Fluid. Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopart ATF+4 Automatic Transmission Fluid. Mopart ATF+4 Automatic Transmission Fluid. Mopart DOT 3 and SAE J1703 should be used. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. Mopart ATF+4 Automatic Transmission Fluid.
MAINTENANCE SCHEDULES CONTENTS m Emission Control System Maintenance . . . . . . . . 294 m Maintenance Schedule . . . . . . . . . . . . . . . . . . . 294 ▫ Schedule “B”—All Engines . . . . . . . . . . . . . . 297 M A I N T E N A N C E ▫ Schedule “A”—2.4L Non Turbo Charged Engines . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305 S C ▫ Schedule “A”—2.4L Turbocharged Engines . . .
M A I N T E N A N C E 294 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B—All Engines” of the 9Maintenance Schedules9 section of this manual. NOTE: Most vehicles are operated under the conditions listed for Schedule 9B9—ALL ENGINES. Second is Schedule “A”—NON TURBO CHARGED ENGINES.
M A I N T E N A N C E 296 MAINTENANCE SCHEDULES Once a Month • Inspect the brake hoses. • Check tire pressure and look for unusual wear or damage. • Inspect the CV joints and front suspension components. • Inspect the battery and clean and tighten the terminals as required. • Check the automatic transaxle fluid level. • Check the fluid levels of coolant reservoir, brake S master cylinder and transaxle and add as needed.
MAINTENANCE SCHEDULES SCHEDULE “B”—ALL ENGINES Follow schedule “B”—All Engines if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an L. Change the manual transaxle fluid every 48,000 miles (77 000 km) if the vehicle is usually operated under one or more of the conditions marked with an †.
M A I N T E N A N C E S C H E D U L E S 8 298 MAINTENANCE SCHEDULES If none of these apply to you, and your vehicle is equipped with a Non–Turbo Charged Engine then change your engine oil at every interval shown on schedule “A”—NON TURBO CHARGED ENGINES in the maintenance schedule section of this manual. Miles (Kilometers) Change engine oil and engine oil filter. Inspect the brake linings. Inspect the engine air cleaner filter. Replace as necessary.* Inspect the PCV make-up air filter.
MAINTENANCE SCHEDULES Miles (Kilometers) Change engine oil and engine oil filter. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace as necessary.* Replace the PCV make-up air filter. Adjust the generator drive belt tension.
M 300 MAINTENANCE SCHEDULES A I N Miles T ( Kilometers) E N Change engine oil and engine oil filter. A Inspect the brake linings. N C Change the brake fluid. If vehicle is used for E trailer towing. S C H E D U L E S 8 Inspect the engine air cleaner filter. Replace as necessary.* Change the manual transaxle fluid.† Inspect the PCV make-up air filter. Replace as necessary.
MAINTENANCE SCHEDULES Miles ( Kilometers) Change engine oil and engine oil filter. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Inspect the PCV make-up air filter. Replace as necessary. Adjust the generator drive belt tension. Change the automatic transaxle fluid and filter.
M 302 MAINTENANCE SCHEDULES A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Inspect the brake linings. N C Inspect the engine air cleaner filter and reE place as necessary.* S C H E D U L E S 8 Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Replace the engine timing belt. * Inspect the PCV make-up air filter. Replace as necessary.
MAINTENANCE SCHEDULES Miles (Kilometers) Change engine oil and engine oil filter. Inspect the brake linings. Change the brake fluid. If vehicle is used for trailer towing. Inspect the engine air cleaner filter and replace as necessary.* Change the manual transaxle fluid.† Flush and replace the engine coolant at 60 months or 102,000 miles. Inspect the PCV make-up air filter. Replace as necessary.
M 304 MAINTENANCE SCHEDULES A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Inspect the brake linings. N C Inspect the engine air cleaner filter and replace as E necessary.* S C H E D U L E S 8 108,000 (173 000) X Inspect the tie rod ends and boot seals. Inspect the PCV make-up air filter. Replace as necX essary. Adjust the generator drive belt tension. Change automatic transaxle fluid and filter.
MAINTENANCE SCHEDULES 305 M SCHEDULE “A”—2.4L NON TURBO CHARGED ENGINES Miles (Kilometers ) [Months] Change engine oil and engine oil filter. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the PCV make-up air filter.
M 306 MAINTENANCE SCHEDULES A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Inspect the brake linings. E Replace the engine air cleaner filter. S C H E D U L E S 8 Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace, if necessary.* Flush and replace the engine coolant at 60 months, regardless of mileage. Replace the PCV make-up air filter. Adjust the generator drive belt tension.
MAINTENANCE SCHEDULES Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Replace the PCV make-up air filter. Adjust the generator drive belt tension. Flush and replace the engine coolant at 60 months or 102,000 miles.
M 308 MAINTENANCE SCHEDULES A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Inspect the PCV valve and replace if necessary. * E S C H E D U L E S 8 * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emissions warranty. ‡ This maintenance is not required if previously replaced.
MAINTENANCE SCHEDULES 309 M SCHEDULE “A”—2.4L TURBOCHARGED ENGINES Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the PCV make-up air filter. Adjust the generator drive belt tension.
M 310 MAINTENANCE SCHEDULES A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Inspect the brake linings.
MAINTENANCE SCHEDULES Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Flush and replace the engine coolant at 60 months, regardless of mileage. Replace the PCV make-up air filter. Adjust the generator drive belt tension.
M 312 MAINTENANCE SCHEDULES A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Inspect the brake linings. E Replace the engine air cleaner filter. S C H E D U L E S 8 Replace the spark plugs. Adjust the generator drive belt tension. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Flush and replace the engine coolant if not done at 60 months. Replace the PCV make-up air filter.
MAINTENANCE SCHEDULES Miles (Kilometers) [Month] Change engine oil and engine oil filter. Inspect the PCV Valve and replace if necessary. * * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emissions warranty. ‡ This maintenance is not required if previously replaced. Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316 ▫ Prepare For The Appointment . . . . . . . . . . . . 316 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 316 m Reporting Safety Defects . . . . . . . . . . . . . . . . . . 321 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 321 m Publication Order Forms . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE 317 The manufacturer has empowered its dealers to make warranty and repair decisions that ensure you are not inconvenienced. There is no need for you to wait for a decision from the manufacturer. If a special circumstance occurs that requires information from the manufacturer, we have asked the dealer’s service management to make the contact on your behalf. • Owner’s name and address This is why you should always talk to your dealer’s service manager first.
IF YOU NEED CONSUMER ASSISTANCE In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico (915) 729–1248 or 729–1240 Outside Mexico (525) 729–1248 or 729–1240 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center.
IF YOU NEED CONSUMER ASSISTANCE Contract, and you require service after your manufacturer’s new vehicle limited warranty expires, please refer to your contract documents, and contact the person listed in those documents. We appreciate that you have made a major investment when you purchased your new vehicle. Your dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with your ownership experience.
IF YOU NEED CONSUMER ASSISTANCE
IF YOU NEED CONSUMER ASSISTANCE MOPART PARTS Mopart fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.
IF YOU NEED CONSUMER ASSISTANCE Call Toll Free at 1–800–890–4038 (U.S.) or 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: www.techauthority.daimlerchrysler.com or www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration.
IF YOU NEED CONSUMER ASSISTANCE WARNING! WARNING! The traction grade is based on braking (straightahead) traction tests and does not include cornering (turning) performance. The temperature grade is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
INDEX 10
INDEX ABS (Anti-Lock Brake) System . . . . . . . . . . . . . . 194 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 267 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 175 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 219 Air Cleaner, Engine . . . . . . . . . . . . . . . . . . . . . . 258 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 261 Air Conditioning Controls . . . . . .
INDEX Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . 135,187 Back-Up Lights . . . . . . . . . . . . . . . . . . . . . . . . . 289 Ball Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259 Keyless Transmitter Replacement . . . . . . . . . . . . 25 Belts, Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 Belts, Engine . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX CD Changer . . . . . . . . . . . . . . . . . . . . . . . . 146,152 CD Player . . . . . . . . . . . . . . . . . . 144,148,150,154,157 CD Player Maintenance . . . . . . . . . . . . . . . . . . . 166 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . 70,166 Center High Mounted Stop Light . . . . . . . . . . . . 289 Central Door Locks . . . . . . . . . . . . . . . . . . . . . . . 20 Chains, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214 Changing A Flat Tire . . . . . .
INDEX Radiator Cap . . . . . . . . . . . . . . Selection of Coolant . . . . . . . . . Corrosion Protection . . . . . . . . . . Crankcase Emission Control System Cruise Light . . . . . . . . . . . . . . . . Cup Holder . . . . . . . . . . . . . . . . . Customer Assistance . . . . . . . . . . .... .... .... ... .... .... .... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267 267 276 258 133 112 316 Dealer Service . . . . . . . . . . . . . . . . . .
INDEX Exhaust Gas Caution . . . . . . . . . . . . . . . . . . . . 220 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . 216 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 235 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 251,290,291 Oil Change Interval . . . . . . . . . . . . . . . . . . . . 252 Oil Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291 Oil Selection . . . . . . . . . . . . . . . . . . . . . . . . . . 253 Oil Synthetic . . . . . . . .
INDEX Filler Cap . . . . . . . . . . . . . . . . . . . . . . . . . 135,221 Filler Door . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258 Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270 Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Heated Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Hood Release . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 269 Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Wiring System . . . . . . . . . . . . . . . . . . . . . . . . 256 Immobilizer . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Latches Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Lead Free Gasoline . . . . . . . . . . . . . . . . . . . . . . 216 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Light Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . 286,287 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61,93 Airbag . . . . . . . . . . . . . . . . . . . . . . . . 45,50,60,134 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Locks Central . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Child Protection . . . . . . . . . . . . . . . . . . . . . . . . 21 Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Power Door . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Steering Wheel . . . . . . . . . . . . . . . . . . . . . . . . . 17 Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . 262 Luggage Rack . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133,135 Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . 251,290 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290 Change Interval . . . . . . . . . . . . . . . . . . . . . . . 252 Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 Filter . . . . . . .
INDEX Steering, Checking . . . . . . . . . . . . . . . . . . . . . 261 Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Power Steering Fluid . . . . . . . . . . . . . . . . . . . . . 292 Pregnant Women and Seat Belts . . . . . . . . . . . . . . 41 Preparation for Jacking . . . . . . . . . . . . . . . . . . . . 232 Pretensioners Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Safety Checks Inside Vehicle . . . . . . . . . . . . . . . . . 60 Safety Checks Outside Vehicle . . . . . . . . . . . . . . . 61 Safety Defects, Reporting . . . . . . . . . . . . . . . . . . 321 Safety Information, Tire . . . . . . . . . . . . . . . . . . . 197 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Satellite Radio . . . . . . . . . . . . . . . . . . . . . . . . . . 161 Satellite Radio Antenna . . . . . . . . . . . . . . . . . . . 164 Schedule, Maintenance . . . . .
INDEX Side Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Side Window Demisters . . . . . . . . . . . . . . . . . . . 173 Slippery Surfaces, Driving On . . . . . . . . . . . . . . . 238 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214 Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231 Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 Speed Control . . . . . . . . . . . . . . . . . . . . . . . 101,133 Speedometer . .
INDEX Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61,206,323 Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 206 Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214 Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 Compact Spare . . . . . . . . . . . . . . . . . . . . . . . . 210 Flat Changing . . . . . . . . . . . . . . . . . . . . . . . . 235 General Information . .
INDEX Transmitter Battery Service . . . . . . . . . . . . . . . . . . 25 Transmitter Programming . . . . . . . . . . . . . . . . . . . 24 Transmitter, Remote Keyless Entry . . . . . . . . . . . . 22 Transporting Pets . . . . . . . . . . . . . . . . . . . . . . . . 58 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . 212 Trip Odometer Reset Button . . . . . . . . . . . . . 133,135 Trunk Release, Emergency . . . . . . . . . . . . . . . . . . 29 Turbo Cool Down . . . . . . . . . . . . . . . .
INDEX Windshield Wipers . . . . . . . . . . . . . . . . . . . . . 98,263 Wiper Blade Replacement . . . . . . . . . . . . . . . . . . 263 341 Wiper, Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 Wipers, Intermittent . . . . . . . . . . . . . . . . . . . . . . .