SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 9 ▫ Automatic (Rolling) Door Locks . . . . . . . . . . . .16 ▫ Sentry Key Engine Immobilizer — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 ▫ Automatic Unlock On Exit (Only Available If Automatic Door Locks Enabled) . . . . . . . . . . . .18 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .12 䡵 Remote Keyless Entry . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Program Additional Transmitters . . . . . . . . .20 ▫ Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . .28 ▫ Transmitter Linked To Memory Programming . .21 ▫ Seat Belts And Pregnant Women . . . . . . . . . . . .32 ▫ General Information . . . . . . . . . . . . . . . . . . . .22 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . .32 ▫ Transmitter Battery Service . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9 A WORD ABOUT YOUR KEYS You can insert the double sided keys into the locks with either side up. have been programmed to the vehicle can be used to start and operate the vehicle for more than the two second validation time period. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys only from your dealer. Ask your dealer for these numbers and keep them in a safe place.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the Sentry Key Immobilizer System indicator light comes on during normal vehicle operation (it has been running for longer than 10 seconds) a fault has been detected in the electronics and the vehicle should be serviced as soon as possible. NOTE: • The Sentry Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 for dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by using the Customer Key Programming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed. NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. this device must accept any interference that may be received, including interference that may cause undesired operation Ignition Key Removal Place the shift lever in Park and make sure that the shift knob push-button (vehicles with floor shift) is in the out position. NOTE: If you try to remove the key before you place the lever in Park, the key may become trapped temporarily in the key cylinder.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Floor Shift Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK and the shift knob push button is out. It also prevents shifting out of PARK unless the key is in the OFF or RUN positions. 2 GLOVE COMPARTMENT LOCK The glove box lock has been designed so that the key can be inserted only about half way. Do not force the key past this point.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ILLUMINATED ENTRY SYSTEM The interior lights will come on when you unlock the vehicle with the remote keyless entry or central unlock. They will remain on for about 30 seconds after all doors are closed then fade to off. The lights also will fade to off if you turn on the ignition after you close all the doors. DOOR LOCKS Power Door Locks There is a door lock switch on each front door trim panel. Press this switch to lock or unlock the four doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 If you press the door lock switch while the keys are in the ignition switch, with the ignition switch in the ACC, LOCK, or OFF position, and the driver’s door is open, the doors will not lock. A chime will sound as a reminder to remove the keys. WARNING! For personal security and safety in the event of an accident, lock the vehicle doors as you drive and when you park and leave the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To use the system, open each rear door and use a key to move the control near the door latch UP to the “Engage” position as shown on the door label. When the system on a door is engaged, that door can be opened only by using the outside door handle. This will occur only if the inside door lock is in the unlocked (up) position. WARNING! Avoid trapping anyone in the vehicle in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 The Automatic Door Locks can be disabled or re-enabled by performing the same following procedure: 3. Depress the power door lock switch to lock the doors. 1. Close all doors and place the key in the ignition. 2 2. Cycle the ignition switch between OFF and ON/RUN and back to OFF 4 times ending up in the OFF position. 4. A single chime will indicate the completion of the programming.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Unlock on Exit (Only Available if Automatic Door Locks Enabled) This feature will unlock all the doors when the driver’s door is opened and the ignition switch is in the LOCK position. This function is disabled as delivered from the factory. Automatic Unlock on Exit can be enabled or disabled by performing the following procedure: 1. Close all doors and place the key in the ignition. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 1. Press and hold the Unlock button on the transmitter. 2. Continue to hold the Unlock button, wait at least 4 but no longer than 10 seconds, then press the Lock button. 3. Release both buttons. Enable/Disable Lamp Flash: The Lamp Flash can be enabled or disabled by performing the following procedure: 1. Press and hold the Lock button on the transmitter. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Panic Alarm The panic alarm unlocks the driver’s door, turns on the interior lights, flashes the headlights and sounds the horn for about 3 minutes or until the alarm is turned off. The vehicle can be driven while in the Panic mode. To Use The Panic Alarm: Press and hold the Panic button to activate the alarm. Press and hold the Panic button or unlock the door with the key to deactivate the alarm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 one second. Release both buttons simultaneously. You will hear a chime to signal that you can proceed with programming the new transmitter. 3. One by one with each transmitter (includes previously programmed as well as the new transmitter), press and release the lock and unlock buttons simultaneously. You will hear a chime after each transmitter has been successfully programmed. You will have 30 seconds to finish programming all new transmitters.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE transmitters are programmed into the vehicle, the first transmitter trained will be associated with memory setting 1, and the second transmitter trained will be associated with memory setting 2. Additional transmitters will not be associated with a memory setting. General Information This transmitter complies with FCC rules part 15 and with RS-210 of Industry Canada.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • Reassemble the transmitter case. Snap the halves together and test transmitter operation. SECURITY ALARM SYSTEM The system monitors the doors, trunk key cylinder, and ignition for unauthorized operation. If something triggers the alarm, the system will signal for up to 18 minutes. For the first 3 minutes the horn will sound and the headlights, park and tail lights and the SET light will flash.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. The SET light on the top of the instrument panel will flash rapidly for 16 seconds. This shows that the system is arming. If the light comes on but does not flash, the system is still armed, but there is a problem in the trunk circuit. After 16 seconds the SET light will continue to flash slowly. This shows that the system is fully armed. To disarm the system: Unlock a front door using either the key or the Keyless Entry Transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 POWER WINDOWS Window controls on the driver’s door control all door windows. The driver’s window switch has an Auto Down feature. Press the window switch past the detent, release, and the window will go down automatically. Press the switch a second time in either direction to stop the window. To open the window part way, press the window switch to the detent and release it when you want the window to stop.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK SAFETY WARNING Trunk Emergency Release WARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat. If trapped in the trunk, children can die from suffocation or heat stroke.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger and side airbags, if equipped, for both the driver and right front passenger. If you will be carrying children too small for adult-size belts, your seat belts also can be used to hold infant and child restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belts All seating positions in your vehicle are equipped with Lap/Shoulder Belts. The belt webbing retractor will lock only during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the belt will lock and reduce your risk of striking the inside of the vehicle or being thrown out. WARNING! • Wearing a seat belt incorrectly is dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the front seat. Center Console removed from following illustrations 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt go around your lap. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is very dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WARNING! WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your dealer and have it fixed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front seats, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push the lever above the webbing upward to release the anchorage, and then move it up or down to the position that serves you best. In the rear seat, move toward the center of the seat to position the belt away from your neck.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! Driver and Right Front Passenger Supplemental Restraint System (SRS) - Airbag Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seats, and their covers are also labeled SRS AIRBAG. WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers are designed to open only when the airbags are inflated.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Airbags inflate in moderate to high speed impacts. Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occupant protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. If your vehicle has side airbags, do not lean against the door, airbags will inflate forcefully into the space between you and the door. WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 • ACM (Airbag Control Module) • SIACM (Side Impact Airbag Control Module) • Interconnecting Wiring How the Frontal Airbag System Works • The front airbag control module determines if a frontal collision is severe enough to require the airbags to inflate. • The airbag control module will not detect side, roll over, or rear collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • When the airbag control module detects an impact requiring the front airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the airbags. The airbag covers separate and fold out of the way as the airbags inflate to their full size. The airbags fully inflate in about 60 milliseconds. This is only about half of the time it takes you to blink your eyes.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 • As the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • In moderate to severe side collisions, the side airbag inflator on the crash side of the vehicle is triggered, releasing a quantity of nontoxic gas. The inflating side airbag exits through the seat seam into the space between the occupant and the door. The side airbag moves at a very high speed and with such a high force, that it could injure you if you are not seated properly, or if items are positioned in the area where the side airbag inflates.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Airbag Light You will want to have the airbags ready for your protection in an impact. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately. • The AIRBAG light does not come on or flickers during the 6 to 8 seconds when the ignition switch is first turned on. • The light remains on or flickers after the 6 to 8 second interval.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants and Child Restraints • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and “convertible” child seats. • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Here are some tips on getting the most out of your child restraint: NOTE: For additional information, refer www.seatcheck.org or call 1–866–SEATCHECK. • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you try a child restraint in the vehicle seats where you will use it before you buy it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large For Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the lap/shoulder belt in the rear seat. • Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 All three rear seating positions have lower anchorages that are capable of accomodating LATCH-compatible child seats. These are round bars, located at the lower area of the seat back. Install your child seat as per child seat manufacturer recommendations. Again, carefully follow the installation instructions that were provided with the child restraint system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE You will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors over the top of the anchorage bars, pushing aside the seat cover material.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 buckle and twist the short buckle-end belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out. 2 If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, you may need to do something more. Disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and remove slack in the tether strap according to the child restraint manufacturer’s instructions. WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 must remain open, close all windows. Adjust the heating or cooling system to force outside air into the vehicle. Set the blower at high speed. SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defrosters Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Cup Holders . . . . . . . . . . . . . . . . . . . . . . . . . .55 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 ▫ Front Seat Cupholders (Concorde Limited Vehicles Only) . . . . . . . . . . .55 ▫ Power Seats . . . . . . . . . . . . . . . . . . . . . . . . . .59 ▫ Rear Seat Cupholders . . . . . . . . . . . . . . . . . . .55 䡵 Coat Hook . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 䡵 Mirrors . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ To Turn The Interior Lights On . . . . . . . . . . . . .65 ▫ Passing Light . . . . . . . . . . . . . . . . . . . . . . . . .69 ▫ Battery Saver Feature—Interior Lights . . . . . . . .65 ▫ Windshield Wipers And Washers . . . . . . . . . . .69 ▫ Instrument Panel Lighting . . . . . . . . . . . . . . . .65 ▫ Speed Sensitive Intermittent Wipers System . . . .70 ▫ Front Map/Reading Lights . . . . . . . . . . . . . . .66 䡵 Tilt Steering Column . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 53 ▫ Programming The Universal Transceiver . . . . . .77 ▫ Sun Roof Maintenance . . . . . . . . . . . . . . . . . . .88 ▫ “Rolling Code” Programming . . . . . . . . . . . . .78 䡵 Electronic Vehicle Information Center (EVIC) — If Equipped . . . . . . . . . . . . . . . . . . .88 ▫ Canadian Programming/Gate Programming . . .80 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 ▫ Reprogramming A Single Button . . . . . . . . . . .80 ▫ Security .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ C/T Button . . . . . . . . . . . . . . . . . . . . . . . . . .98 ▫ Manual Compass Calibration . . . . . . . . . . . . . .98 ▫ Compass/Temperature Display . . . . . . . . . . . .98 ▫ Outside Temperature . . . . . . . . . . . . . . . . . . . 100 ▫ Automatic Compass Calibration . . . . . . . . . . . .98 䡵 Electrcal Power Outlet . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 55 CUP HOLDERS Front Seat Cupholders (Concorde Limited Vehicles Only) The cupholders are located in the forward edge of the console. Press the forward edge of the console to release the cupholders. Press the cupholder back into the console when they are no longer needed. Rear Seat Cupholders The rear cupholders are located in the rear seat folding arm rest. Lower the arm rest and the cupholders are exposed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Adjusting The Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustment. Automatic Dimming Mirror Feature This mirror will automatically adjust for annoying headlight glare from vehicles behind you. Push in the button on the base of the mirror to activate the dimming feature. A green light in the button will illuminate when this feature is on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 57 Electric Remote Control Mirrors NOTE: Pre selected power mirror positions (for driver seat only) can be controlled by the Memory Seat Feature. Refer to the Seats section which follows. Press the L or R button located on the driver’s door panel for Left or Right mirror selection. NOTE: Place the mirror switch in the neutral (center) position to prevent accidental changing of the mirror setting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in this convex mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 59 SEATS Power Seats The power seat switch is on the outboard side of the seat near the floor. Use this switch to move the driver’s seat up or down, forward or rearward, or to tilt the seat. The passenger’s seat will move forward or rearward. WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. During exit, the seat will move rearward from the set position when the key is removed from the ignition providing that the seat is not in the full rearward position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 61 Lumbar Support This feature allows you to increase or decrease the amount of lumbar support. Turn the control level forward to increase and rearward to decrease the desired amount of lumbar support. Press the switch once to select a heat setting (high or low) and press the switch a second time to turn the heated seat off. 3 NOTE: Once a heat setting is selected, heat will be felt within 2 to 3 minutes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The memory feature switch is located on the outboard side of the driver’s seat, next to the heated seat switch. 3. A second memory setting can be stored in the vehicle memory. Begin with pressing 2 on the memory seat switch for driver 2. Select a second seat/radio setting, press the Set (S) button, then press button 2 within 5 seconds. Each time the Set and a numbered button are pressed, the old memory is erased, and a new one is stored.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 63 3. Press and release the Set (S) button on the memory seat switch, then press and release button 1 or 2. 4. Press and release the Lock button on the transmitter. 5. Do not press any buttons for 10 seconds. NOTE: Your transmitters may be unlinked to your memory settings by pressing the Unlock button on the transmitter in step 4 above.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull up on the hood release lever located under the instrument panel. Then lift up on the catch located under the front edge of the hood, near the center. To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center frone edge of the hood to ensure that both latches engage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65 WARNING! NOTE: The map lights or reading lights that are manually switched on will not turn off automatically. If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. Instrument Panel Lighting The brightness of the instrument panel lighting can be regulated by rotating the dimmer switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE on during the daytime such as in a parade or a funeral procession. To activate this feature, rotate the Dimmer Control upward to the first detent. EXTERIOR LIGHTS Headlights And Parking Lights Front Map/Reading Lights These lights are mounted between the sun visors. Each light is turned On by pressing the lens. Press the lens a second time to turn the light Off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 Automatic system off, turn the headlight switch clockwise, to the off position. The engine must be running before the headlights will come on in the automatic mode. NOTE: The Automatic Headlight System will turn on the headlights if it detects that the windshield wipers have been in operation for more than 10 seconds.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Battery Saver Feature If an exterior light is left on when the ignition switch is moved to the Off position, it will automatically turn off after 10 minutes. Normal operation will resume when the ignition is turned On or when the headlight switch is turned to another position. MULTIFUNCTION CONTROL LEVER Fog Lights Turn the headlight switch to any ON position, then pull out the headlight switch knob to turn on the fog lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 Headlight Dimmer Switch Pull the multi-function control lever toward the steering wheel to switch the headlights from high or low beam. Passing Light You can signal another vehicle with your headlights by lightly pulling the multi-function lever toward the steering wheel. This will cause the headlights to turn on at high beam and remain on until the lever is released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the button is pushed and held while in the OFF position, the wiper will operate for several wipes then turn off. If the button is pushed while in the OFF position, the wipers will cycle twice. NOTE: The Automatic Headlight System will turn on the headlights if it detects that the windshield wipers have been in operation for more than 10 seconds. WARNING! Sudden loss of visibility through the windshield could lead to an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 TILT STEERING COLUMN To tilt the column, pull the small lever below the turn signal control toward you and move the wheel up or down, as desired. Release the lever to lock the wheel firmly in place. WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TRACTION CONTROL SWITCH — IF EQUIPPED To turn the Traction Control System Off, press the switch located on the instrument panel, to the right of the steering column, until the TRAC OFF light in the instrument cluster lights up. To turn the Traction Control System On, press the switch until the TRAC OFF light in the instrument cluster turns off. NOTE: Traction Control System comes on each time the ignition switch is turned On.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 To Activate: Push the ON/OFF button to turn the system ON. The CRUISE light in the instrument cluster will illuminate when the system is ON. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Resume Speed: To resume a previously set speed, push and release the ACCEL/RESUME button. Resume can be used at any speed above 25 mph (40 km/h). To Accelerate For Passing: Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. To Vary The Speed Setting: When the speed control is engaged, speed can be increased by pressing and holding the ACCEL/RESUME button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 downshift again to second gear. The transmission will upshift as the vehicle reaches the top of the hill. When Descending A Hill If vehicle speed rises 3 mph (5 km/h) over the Speed Control SET speed, the transmission will downshift to third gear. This provides engine braking to keep vehicle speed under control. The transmission will not downshift below third gear to control vehicle overspeed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The dome/reading lights illuminate when a door is opened or when the interior lights are turned on by rotating the dimmer control located on the multi-function lever. The reading lights are activated by pressing on the recessed area of the corresponding lens. NOTE: The dome/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 WARNING! WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features it could cause injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Step 2 does not have to be followed to program additional hand held transmitters. 3. Choose one of the three buttons to train. Place the hand held controller one to three inches from the universal transceiver while keeping its indicator light in view. NOTE: Some entry gates and garage door openers may require you to replace step 4 with the procedures listed under Canadian Programming. 5.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 manufactured after 1996, your garage door opener or other device may have a “Rolling Code” system. On garage door openers with the “Rolling Code” feature, the transmitter code changes after each use to prevent the copying of your code. To check if your device is protected by a “Rolling Code” system: • Check the owner’s manual for the device for mention of “Rolling Codes”. • Press and hold the programmed button on the Universal Transceiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE use either your Universal Transceiver or your original hand-held transmitter to open you garage door.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. HomeLink威 is a trademark owned by Johnson Controls, Inc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Contact HomeLink威 at 1–800–355–3515 for safety information or assistance or on the internet at www.homelink.com.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 2. Erase the factory test codes by pressing and holding channels button one and three, of the universal transceiver, until CLEARED CHANNELS displays (about 20 seconds). Release the buttons. NOTE: Step 2 does not have to be followed to program additional hand held transmitters. 3. Choose one of the three universal transceiver buttons to program.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE both buttons. Your universal transceiver is now programmed. After a button has been trained, TRANSMIT will appear in the display when the button is pressed. NOTE: Some entry gates and garage door openers may require you to replace step 4 with the procedures listed under Canadian Programming.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 light flashes rapidly and then stays on after 2 seconds, the device has the “Rolling Code” feature. To train a garage door opener (or other rolling code equipped devices) with the rolling code feature, follow these instructions after completing the Programming portion of this text: NOTE: The assistance of a second person may make the following programming procedure quicker and easier. 1. Locate the programming button on the garage door opener motor head unit.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Continue to press and hold the Universal Transceiver button while you press and release the hand held transmitter button until the frequency signal has been learned. Release both buttons when TRAINED appears in the display. Operation Press the desired universal transceiver button. The display shows that the appropriate channel signal is being transmitted and the programmed device should operate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 HomeLink威 is a registered trademark owned by Johnson Controls, Inc. POWER SUN ROOF — IF EQUIPPED The sun roof controls are located on the overhead console. If the sun roof is vented and you wish to open it, press and hold the OPEN button. If the sun roof is open and you wish to vent it, press and hold the VENT button. The sunshade can be opened manually. It will also open as the sun roof opens. The sunshade cannot be closed if the sun roof is open.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if so equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 • WASHER FLUID LOW (with graphic) • MEMORY SEAT DISABLED VEHICLE (not in Park) Espanol. As you continue the displayed information will be shown in the selected language. Customer Programmable Features Press the MENU button until one of the display choices following appears: 3 US or Metric Pressing the STEP button when in this display selects US or Metric. The overhead console and instrument panel displays will be in the selected units.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Auto Door Locks When this feature is selected, all doors lock automatically when the speed of the vehicle reaches 15 mph (25 km/h). Pressing the STEP button when in this display will select “Yes” or “No.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 feature selected. Pressing the STEP button when in this display will select “Yes” or “No.” Headlamp Delay When this feature is selected the driver can choose, when exiting the vehicle, to have the headlamps remain on for 30, 60, or 90 seconds, or not remain on. Pressing the STEP button when in this display will select 30, 60, 90, or OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE STEP button when in this display will select “Yes” or “No.” Tilt Mirrors Down When this feature is selected, and the vehicle is placed in reverse, the driver’s exterior mirror will tilt downward to improve visibility of rear wheel area. Once reverse is disengaged, the driver’s exterior mirror will return to it’s original position. Pressing the STEP button when inthis display will select “YES” or “NO”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Compass/Temperature/Trip Computer This display provides the outside temperature, one of the eight compass headings to indicate the direction the vehicle is facing, and vehicle trip information. The compass and temperature display is the normal display. When the C/T button is pressed or the customer programmable features have been “stepped through” the compass/temperature display returns.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Step Button Press the STEP button to cycle through all of the Compass/Mini-Trip Computer displays. Trip Odometer Shows the distance travelled since the last reset. Elapsed Time Shows the accumulated ignition ON time since the last reset. Miles to Service Shows the distance remaining to require service. NOTE: This display can be reset to the set service interval by pressing and holding the RESET button for 3 seconds. Blank Screen Shows a blank screen.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 After completing three 360° turns in an area free from large metal or metallic objects, the CAL symbol will turn off and the compass will function normally. Manual Compass Calibration If the compass appears erratic and the CAL symbol does not appear, you must manually put the compass into the “Calibration” mode.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press the RESET button approximately five seconds. The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Global Reset If the RESET button is pressed twice within 3 seconds while in any of the 3 resetable displays, the Global Reset button will reset all 3 displays. Step Button Use this button to choose or cycle through the five trip conditions. Average Fuel Economy (AVG ECO) This display shows the average fuel economy since the last reset. US/M Button Use this button to change the display from U.S. to metric measurement units.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Trip Odometer (ODO) This display shows the distance traveled since the last reset. three 360 turns at about 5 mph (8 km/h) in an area free from large metal or metallic objects, the CAL symbol will turn off and the compass will function normally. Elapsed Time (ET) This display shows the accumulated ignition ON time since the last reset. Manual Compass Calibration If the compass appears erratic and the CAL light does not appear, you must calibrate the compass.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 scroll through numbers 1 through 15. Press the RESET button after selecting the proper zone to return to the normal compass/temperature display. NOTE: To ensure proper compass calibration, make sure the compass variance is properly set before manually calibrating the compass (see variance map).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Temperature Because engine temperature can increase the displayed temperature, temperature readings are slowly updated when vehicle speed is below 20 mph (30 km/h). ELECTRCAL POWER OUTLET Your vehicle is equipped with one power outlet which is located in the forward portion of the center console if your vehicle has bucket seats or in the lower center of the instrument panel if your vehicle has bench or split bench seats.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instruments And Controls . . . . . . . . . . . . . . . . 105 ▫ Power Switch, Volume Control . . . . . . . . . . . . 114 䡵 Instruments And Controls (Concorde Limited Only) . . . . . . . . . . . . . . . . 106 ▫ Seek Button (Radio Mode) . . . . . . . . . . . . . . . 115 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . 107 䡵 Instrument Cluster (Concorde Limited Only) . . 108 䡵 Instrument Cluster Description . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Seek Button . . . . . . . . . . . . . . . . . . . . . . . . . 118 ▫ Tape CD Button . . . . . . . . . . . . . . . . . . . . . . 121 ▫ Fast Forward (FF) . . . . . . . . . . . . . . . . . . . . . 118 ▫ Time Button . . . . . . . . . . . . . . . . . . . . . . . . . 121 ▫ Rewind (RW) . . . . . . . . . . . . . . . . . . . . . . . . 118 ▫ Scan Button . . . . . . . . . . . . . . . . . . . . . . . . . 121 ▫ Tape Eject . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 103 ▫ Mode Button . . . . . . . . . . . . . . . . . . . . . . . . 123 ▫ Program Button 1 . . . . . . . . . . . . . . . . . . . . . 132 ▫ Cassette Player Features . . . . . . . . . . . . . . . . 123 ▫ Program Button 4 (Random Play) . . . . . . . . . . 132 ▫ CD Changer Control Capability — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 ▫ Program Button 5 . . . . . . . . . . . . . . . . . . . . . 132 ▫ Radio Display Messages . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Radio Operation And Cellular Phones . . . . . . . 136 䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 137 ▫ Manual Air Conditioning/Heater Operation . . 137 ▫ Automatic Temperature Control (ATC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 105 INSTRUMENTS AND CONTROLS 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENTS AND CONTROLS (Concorde Limited Only)
UNDERSTANDING YOUR INSTRUMENT PANEL 107 INSTRUMENT CLUSTER 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER (CONCORDE LIMITED ONLY)
UNDERSTANDING YOUR INSTRUMENT PANEL 109 INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gauge When the ignition is in the ON position, the pointer will show the level of fuel remaining in the tank. 2. Low Fuel Warning Light When the fuel level drops to about 2 gallons (8 liters), the Low Fuel symbol will light and remain lit until fuel is added. A warning chime will sound when the light comes on. 3. Low Oil Pressure Light This light indicates low engine oil pressure.
UNDERSTANDING YOUR INSTRUMENT PANEL 7. Turn Signal Indicators The arrow will flash in unison with the exterior turn signal, when using the turn signal lever. 8. High Beam Indicator This light shows that the headlights are on high beam. Pull the turn signal lever towards the steering wheel to switch the headlights from high or low beam. 12. Low Washer Fluid Light This symbol will light whenever the fluid reservoir is less than 1/4 filled.
UNDERSTANDING YOUR INSTRUMENT PANEL 111 If the pointer rises to the “H” mark, stop the vehicle and turn off the engine until the problem is corrected. There are steps that you can take to slow down an impending overheat condition. If your air conditioning is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat. You can also turn the Temperature control to maximum heat, the Mode control to Floor and the Fan control to High.
UNDERSTANDING YOUR INSTRUMENT PANEL correct mileage that the vehicle has been driven. Therefore, if the odometer reading is changed during repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined. The Trip Odometer shows individual trip mileage and is accessed by pressing the reset button. 20. Charging System Light This light shows the status of the electrical charging system.
UNDERSTANDING YOUR INSTRUMENT PANEL 113 This light monitors both the brake fluid level and the parking brake. If the light comes on, it indicates either that the parking brake is on or there is a low fluid level in the brake master cylinder. On vehicles equipped with anti-lock brakes (ABS), the brake light may also indicate reduced braking performance. If the parking brake is off and the light remains on, have the brake system inspected as soon as possible.
UNDERSTANDING YOUR INSTRUMENT PANEL If your vehicle is a Concorde Limited, you can ask your dealer to enable the digital clock to be displayed continuously when the radio is off and the ignition switch is on. SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE TAPE PLAYER AND CD PLAYER — IF EQUIPPED Clock Setting Procedure 1. Turn the ignition switch to the ON or ACC position. Using the point of a ballpoint pen or similar object, press either the hour (H) or minute (M) buttons on the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 115 Seek Button (Radio Mode) Press and release the Seek button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. Holding the button will by pass stations until you release the button. Tuning Press the TUNE control up or down to increase or decrease the frequency. If you press and hold the button, the radio will continue to tune until you release the button.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather Radio Display Soft Soft Rck Soft R&B Sports Talk Top 40 Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station.
UNDERSTANDING YOUR INSTRUMENT PANEL 117 AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received. Scan Button Pressing the SCAN button causes the tuner to search for the next station, in either AM or FM, pausing for 5 seconds at each listenable station before continuing to the next. Pressing the AM/FM button continues the search in the alternate frequency band.
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Button Press the SEEK button up for the next selection on the tape and down to return to the beginning of the current selection. Press the SEEK button up or down to move the track number to skip forward or backward 1 to 6 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc. Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing.
UNDERSTANDING YOUR INSTRUMENT PANEL 119 Noise Reduction The Dolby Noise Reduction System* is on whenever the tape player is on, but may be switched off. To turn off the Dolby Noise reduction System: Press the Dolby button (button 2) after you insert the tape. The NR light in the display will go off when the Dolby System is off. The Dolby System is automatically reactivated each time a tape is inserted. * ”Dolby” noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
UNDERSTANDING YOUR INSTRUMENT PANEL EJT CD (Eject) Button Press this button and the disc will unload and move to the entrance for easy removal. The unit will switch to the radio mode. Press TUNE FF to fast forward through the tracks. Press the FF button a second time to stop the fast forward feature. If TUNE RW is pressed, the current track will reverse to the beginning of the track and begin playing. If you do not remove the disc within 15 seconds, it will be reloaded.
UNDERSTANDING YOUR INSTRUMENT PANEL 121 Tape CD Button Press this button to select between CD player and Tape player. SALES CODE RBB—AM/FM STEREO RADIO WITH CASSETTE TAPE PLAYER AND CD CHANGER CAPABILITY Time Button Press this button to change the display from elapsed CD playing time to time of day. 4 Scan Button Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time.
UNDERSTANDING YOUR INSTRUMENT PANEL Power Button The volume control/power button pops out when pressed, this turns the sound system ON in the mode last used. Pushing the button back in turns the sound system OFF. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it.
UNDERSTANDING YOUR INSTRUMENT PANEL 123 stations to be locked into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice. Every time a preset button is used a corresponding button number will be displayed. Balance The balance control adjusts the left-to-right speaker balance. Press the BAL button in and it will pop out. Adjust the balance and push the button back in. Fade The fade control provides for balance between the front and rear speakers.
UNDERSTANDING YOUR INSTRUMENT PANEL Music Search Pressing the SEEK button while playing a tape will start the Music Search mode. Press the SEEK button up for the next selection on the tape and down to return to the beginning of the current selection, or return to the beginning of the previous selection if the tape is within the first 5 seconds of the current selection. The SEEK symbol appears on the display when Music Search is in operation.
UNDERSTANDING YOUR INSTRUMENT PANEL 125 Mode Button To activate the CD changer, press the MODE button until CD information appears on the display. Push-Button While the CD changer is playing, press the NUMBER 1 push-button or the NUMBER 5 push-button to select a disc numbered higher or lower than the one currently being played. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display.
UNDERSTANDING YOUR INSTRUMENT PANEL Radio Display Messages Your radio has been designed to display certain messages when a problem is detected with the CD player. SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch.
UNDERSTANDING YOUR INSTRUMENT PANEL 127 Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will bypass stations without stopping until you release it. Bass and Treble Tone Control The tone controls consist of 2 separate bands.
UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice.
UNDERSTANDING YOUR INSTRUMENT PANEL 129 display will show the track number and index time in minutes and seconds. Play will begin at the start of track one. Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection.
UNDERSTANDING YOUR INSTRUMENT PANEL CD Changer Operation — If Equipped MODE Press the MODE button to select between the cassette tape player, CD player, and the CD changer (if equipped). Disc/Program Button 1 Press the DISC (button 1) button to play the next available disc. Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play.
UNDERSTANDING YOUR INSTRUMENT PANEL 131 6 DISC CD CHANGER — IF EQUIPPED The CD changer is located below the radio in the instrument panel. The changer plays only 4 3⁄4 inch (12 cm) discs. The changer holds up to 6 discs. Each disc is loaded and ejected through a single slot in front of the changer. Each disc has a numbered button with an amber light above it which, when illuminated, indicates that a disc is loaded in that particular chamber.
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Button Press the top of this button on the radio once to play the next track. Press the bottom of the button once to return to the beginning of the current track. Press the bottom of the button twice to play the previous track. FF/TUNE/RW Press the FF (fast forward) button and the CD player will fast forward through the tracks until the button is released.
UNDERSTANDING YOUR INSTRUMENT PANEL 133 • Pressing the AM/FM button while in the tape or CD mode will select the radio mode. • If in the CD mode and the last CD is ejected, the radio will tune to the last station selected. REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches.
UNDERSTANDING YOUR INSTRUMENT PANEL Pressing the center button will make the radio switch between the various modes available (AM/FM/TAPE/ CD, Etc.). The left hand control is a rocker type switch with a push-button in the center. The function of the left hand control is different depending on which mode you are in. The following describes the left hand control operation in each mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 135 If you press the switch up or down twice it plays the second track, three times, it will play the third, etc. The button in the center of the left hand switch will cause the CD changer to play the next available disc. CASSETTE TAPE AND PLAYER MAINTENANCE To keep the cassette tapes and player in good condition, take the following precautions: 1. Do not use cassette tapes longer than C-90; otherwise, sound quality and tape durability will be greatly diminished. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL COMPACT DISC MAINTENANCE To keep the compact discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6.
UNDERSTANDING YOUR INSTRUMENT PANEL 137 CLIMATE CONTROLS Manual Air Conditioning/Heater Operation to the O (Off) position to shut off the fan and to prevent any outside air from entering the vehicle. This also turns off the A/C compressor. Temperature Control Use this control to regulate the temperature of the air inside the passenger compartment. The blue area of the control indicates cooler temperatures while the red area indicates warmer temperatures.
UNDERSTANDING YOUR INSTRUMENT PANEL Panel Recirculation Directs all air through the panel outlets. Bi-Level Recirculation Directs air through the panel and floor outlets. NOTE: Continuous use of the Recirculate modes may make the inside air stuffy. Use of these modes for longer than fifteen minutes is not recommended. The A/C compressor turns on automatically when this mode is selected. This is to help reduce moisture build up on the windshield.
UNDERSTANDING YOUR INSTRUMENT PANEL 139 NOTE: The air conditioning compressor operates in this mode. This dehumidifies the air to help dry the windshield. To improve fuel economy, leave in the Defrost mode only when necessary. A/C Pushbutton With the fan control in the ON position, pushing the A/C button turns on the air conditioning compressor. An indicator light above the button shows that the Air Conditioning compressor is on. Conditioned air is now directed through the outlets selected.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The defroster turns off automatically after 15 minutes of operation. Each later activation will allow 7 1/2 minutes of operation. Automatic Temperature Control (ATC) — If Equipped CAUTION! To avoid damaging the electrical conductors, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the rear window. Labels can be peeled off by soaking with warm water.
UNDERSTANDING YOUR INSTRUMENT PANEL 141 near the windshield glass. The In-Car Temperature Sensor is mounted behind the ATC control panel. These sensors transmit data on sun strength and vehicle interior temperatures to enhance system performance. Fan Control Use this control to regulate the amount of air forced through the system in any mode you select. Turn the control clockwise to increase fan speed. Do not cover either sensor with any foreign material as improper operation of the system will result.
UNDERSTANDING YOUR INSTRUMENT PANEL The system adjusts to bring the interior temperature to the desired comfort level. All comfort settings are automatic; even Hi and Low. NOTE: You can change the display from U.S. to metric units by pressing the Mix and Panel mode buttons simultaneously or by pressing the English/Metric button on the overhead console. Air Conditioning Button Press this button to turn on the air conditioning compressor.
UNDERSTANDING YOUR INSTRUMENT PANEL 143 Panel Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct air flow. This mode is not recommended when heat is required. NOTE: There is a varying difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature provides improved comfort during sunny but cool conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The defroster turns off automatically after 15 minutes of operation. Each later activation will allow 7 1/2 minutes of operation. CAUTION! To avoid damaging the electrical conductors, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the rear window. Labels can be peeled off by soaking with warm water. Window Fogging In mild but rainy or humid weather, your windows may fog up on the inside.
UNDERSTANDING YOUR INSTRUMENT PANEL 145 Rear Seat Air Outlets The center console on vehicles with bucket seats has upper and lower outlets located on the rear of the console. Air is directed through the outlets in all Modes. A control can be used to direct the flow of air to either the upper or lower outlets. On vehicles with 50/50 bench seats, air is routed under the seats.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips (Manual A/C and ATC)
UNDERSTANDING YOUR INSTRUMENT PANEL 147 Outside Air Intake Make sure that the air intake directly in front of the windshield is free of obstructions. Leaves, snow, etc., could block air flow into the vehicle.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 151 䡵 Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . 156 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 151 䡵 Brake System . . . . . . . . . . . . . . . . . . . . . . . . . 157 ▫ Extremely Cold Weather (Below -20°F Or -29°C) . . . . . . . . . . . . . . . . . 151 ▫ Anti-Lock Brake System (ABS) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . . 163 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . . 169 ▫ Tire Chains . . . . . . . . . . . . . . . . . . . . . . . . . . 163 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . . 169 ▫ Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 164 ▫ Sulfur In Gasoline . . . . . . . . . . . . . . . . . . . . . 169 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 151 STARTING PROCEDURES WARNING! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. The gear selector must be in the NEUTRAL or PARK position before you can start the engine. Apply the brakes before shifting to any driving gear. Normal Starting Normal Starting of either a cold or a warm engine does not require pumping or depressing the accelerator pedal.
STARTING AND OPERATING If Engine Fails To Start CAUTION! Do not try to push or tow your vehicle to get it started. Your vehicle cannot be started this way. Pushing with another vehicle may damage the transaxle or the rear of your vehicle. See Section 6 of this manual for the proper jump starting procedures. If the engine fails to start after following the Normal Starting procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine.
STARTING AND OPERATING 153 After Starting The idle speed will automatically decrease as the engine warms up. ENGINE BLOCK HEATER — Optional U.S. and Standard Canada These heaters use a common power cord which is stored under the hood, behind the Air Cleaner housing. Plug the cord into any 110 volt AC outlet and both heaters will be energized. Use the heaters when temperatures below 0°F (-18°C) are expected to last for several days.
STARTING AND OPERATING Transaxle Reset Mode The transaxle is monitored for abnormal conditions. If a condition is detected that could cause damage, the transaxle automatically shifts into second gear. The transaxle remains in second gear despite the forward gear selected. Park (P), Reverse (R), and Neutral (N) will continue to operate. This Reset feature allows the vehicle to be driven to a dealer for service without damaging the transaxle.
STARTING AND OPERATING 155 WARNING! Never use the Park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. “R” Reverse Shift into this range only after the vehicle has come to a complete stop. under heavy loading conditions (in hilly terrain, traveling into strong head winds, or while towing heavy trailers, use the “3” range). “3” Drive This range eliminates shifts into Overdrive.
STARTING AND OPERATING “L” Low This range should be used for maximum engine braking when descending steep grades. In this range, up-shifts will occur only to prevent engine over speed while down shifts occur as early as possible. Before leaving the vehicle, make sure that the parking brake is fully applied and place the gear selector in the Park position. To release the parking brake, pull the release lever located on the lower edge of the instrument panel.
STARTING AND OPERATING 157 precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied when the driver is not in the vehicle. WARNING! • Leaving children in a vehicle unattended is dangerous for several reasons. A child or others could be injured. Children should be warned not to touch the parking brake or the gear selector. Don’t leave the keys in the ignition.
STARTING AND OPERATING signals for the ABS computer. However, the system will compensate when the compact spare is in use. During stops where ABS is activated, a vibration of the brake pedal may be felt and associated system noises may be heard. WARNING! Pumping of the brake pedal will diminish the effectiveness of Anti-lock brakes and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
STARTING AND OPERATING 159 TRACTION CONTROL— IF EQUIPPED The Traction Control System reduces wheel slip and maintains traction at the driving (front) wheels. The system reduces wheel slip by engaging the brake on the wheel that is losing traction while spinning. The traction system operates at speeds below 35 mph (56 km/h).
STARTING AND OPERATING 1. Safety— WARNING! • Improperly inflated tires are dangerous and can cause accidents. • Under inflation increases tire flexing and can result in tire failure. • Over inflation reduces a tire’s ability to cushion shock. Objects on the road and chuck holes can cause damage that results in tire failure. • Unequal tire pressures can cause steering problems. You could lose control of your vehicle.
STARTING AND OPERATING 161 Tire Inflation Pressures The proper tire pressure for your vehicle is listed on a label attached to the rear face of the driver’s door. The pressure should be checked and adjusted at least once every month. Check more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. period. The cold inflation pressure must not exceed the maximum values molded into the tire side wall. Tire pressure may increase from 2 to 6 psi [.13 to.
STARTING AND OPERATING WARNING! High speed driving with your vehicle under load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Radial-Ply Tires WARNING! Combining radial ply tires with other tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Always use radial tires in sets of four.
STARTING AND OPERATING 163 WARNING! WARNING! Temporary-use spare tires are for emergency use only. With the compact spare tire assembly installed on your vehicle, do not exceed 50 mph (80 km/h). Vehicle handling and braking performance will be reduced. Also, do not drive more than 50 mph (80 km) with the compact spare installed. Failure to follow compact spare tire warning may result in an accident and/or fatal injury. Temporary-use spare tires have a total tread life of 2,000 miles (3 200 km).
STARTING AND OPERATING Snow Tires Some areas of the country require the use of snow tires during winter. Standard tires are of the all season type and satisfy this requirement as indicated by the M+S designation on the tire sidewall. If you need snow tires, see the tire pressure label for size(s) and inflation pressure(s). Snow tires may have a lower speed rating than factory equipped tires and may not match the maximum vehicle speed.
STARTING AND OPERATING 165 Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct inflation pressure. The manufacturer strongly recommends that you use tires equivalent to the originals in size, quality and performance when replacement is needed (see the paragraph on tread wear indicators). Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle.
STARTING AND OPERATING CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. Check with your dealer before replacing tires with a different size. Tire Rotation Recommendations Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear patterns.
STARTING AND OPERATING 167 Alignment And Balance The suspension components of your vehicle should be inspected and aligned when needed to obtain full tire tread mileage. Poor suspension alignment may result in: • fast tire wear; • uneven tire wear, such as feathering and one-sided wear; FUEL REQUIREMENTS Your engine is designed to meet all emissions regulations and provide satisfactory fuel economy and performance when using high quality unleaded gasoline having an octane range of 87 to 89 or higher.
STARTING AND OPERATING Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifications (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available.
STARTING AND OPERATING 169 MMT in Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane number. Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT. Gasolines blended with MMT have shown to reduce spark plug life and reduce emission system performance in some vehicles. The manufacturer recommends using gasolines without MMT.
STARTING AND OPERATING unleaded gasoline having lower sulfur to determine if the problem is fuel related prior to returning your vehicle to an authorized dealer for service. CAUTION! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. CAUTION! If the Malfunction Indicator Light is flashing, immediate service is required. See the On Board Diagnostics paragraph in the Maintenance section of this manual.
STARTING AND OPERATING 171 Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door, on the driver’s side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. VEHICLE LOADING The load carrying capacity of your vehicle is shown in the following sample chart and on the tire pressure label attached to the driver’s door.
STARTING AND OPERATING Luggage Racks External racks do not increase the total load carrying capacity of the vehicle. Be sure the total occupant and luggage load inside the vehicle, plus that on the external rack, do not exceed the rated vehicle capacity shown on the Vehicle Loading Capacity chart. • For vehicles equipped with 2.7L engines: when driving in hot weather (more than 95°F, 35°C), maximum vehicle speed when towing a trailer should not exceed 65 mph (105 km/h).
STARTING AND OPERATING 173 WARNING! Connecting trailer brakes to your vehicle’s hydraulic brake lines can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. • Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are recommended for motoring safety.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 176 䡵 Jump-Starting The Battery . . . . . . . . . . . . . . . 182 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 176 䡵 Driving On Slippery Surfaces . . . . . . . . . . . . . 185 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 177 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . . 185 ▫ Preparations For Jacking . . . . . . . . . . . . . . . . 178 ▫ Traction . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is on the steering column, just behind the steering wheel. Push in the flasher switch and all front and rear directional signals will flash. Press the flasher switch a second time to turn the flashers off. If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and the vehicle locked. NOTE: With extended use, the flasher may run down your battery.
WHAT TO DO IN EMERGENCIES 177 the fan control to High. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, turn the engine off immediately, and call for service.
WHAT TO DO IN EMERGENCIES Preparations For Jacking • Turn on the Hazard Warning Flashers and park the vehicle on a firm level surface, avoiding ice or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. Jacking and Changing a Tire 1. Block the wheel diagonally opposite the flat tire.
WHAT TO DO IN EMERGENCIES 179 3. Before raising the vehicle, use the lug wrench to loosen the lug nuts of the flat tire. 4. Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange, use the lift area closest to the flat tire.
WHAT TO DO IN EMERGENCIES 5. Raise the vehicle just enough to remove the flat tire and install the spare tire. 6. Remove the lug nuts, wheel cover (if equipped) and tire. Remove the cover by hand, do not pry off. 7. Mount the spare tire. For vehicles equipped with wheel covers, see the wheel cover installation instructions. Do not attempt to install a wheel cover on a compact spare. 8. Tighten all the lug nuts on the mounting studs.
WHAT TO DO IN EMERGENCIES 181 9. Lower the vehicle to the ground by turning the jack handle counterclockwise. Compact Spare Tire-For Temporary Emergency Use Only 10. Fully tighten the lug nuts. Torque the wheel lug nuts to 100 ft/lb. (135N. m). • Keep tire inflated to 60 PSI (414 KPa) Cold Inflation Pressure. 11. Store the flat tire, jack and tools. • Avoid driving more than 50 miles (80 km) before replacing tire and wheel.
WHAT TO DO IN EMERGENCIES Wheel Cover Installation (If Required) JUMP-STARTING THE BATTERY WARNING! Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be hurt by the fan. CAUTION! 1. Tighten the two lug nuts on the mounting studs on each side of the stud which is in alignment with the valve stem. 2. Align the valve notch in the wheel cover with the valve stem on the wheel. 3.
WHAT TO DO IN EMERGENCIES 183 WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush the contaminated area immediately with large quantities of water. A battery generates hydrogen gas which is flammable and explosive. Keep flame or spark away from the vent holes.
WHAT TO DO IN EMERGENCIES Check the Battery Test Indicator. If a light or bright colored dot is visible in the indicator, DO NOT jump-start the battery. If the indicator is dark or shows a green dot, proceed as follows: 1. Wear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. 2. When boost is provided by a battery in another vehicle, park that vehicle within booster cable reach but without letting the vehicles touch.
WHAT TO DO IN EMERGENCIES 185 6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan. DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the front wheels to pull erratically to the right or left.
WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE If your vehicle is equipped with Traction Control, turn the system off before attempting to “rock” the vehicle. If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth between Reverse and Drive.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 2.7L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 189 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . . . 203 䡵 3.5L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 190 ▫ Air Conditioner . . . . . . . . . . . . . . . . . . . . . . 204 䡵 Onboard Diagnostic System (OBD II) . . . . . . . 191 ▫ Power Steering Fluid Check . . . . . . . . . . . . . . 205 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Fuel System Hoses . . . . . . . . . . . . . . . . . . . . 217 ▫ Fog Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . . 217 ▫ Center Stop Light . . . . . . . . . . . . . . . . . . . . . 231 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 ▫ Tail, Stop, Back Up, And Turn Signal Lights . . 231 䡵 Fuses . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 189 2.
MAINTAINING YOUR VEHICLE 3.
MAINTAINING YOUR VEHICLE 191 ONBOARD DIAGNOSTIC SYSTEM (OBD II) To meet new government regulations and promote cleaner air, your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transaxle control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing.
MAINTAINING YOUR VEHICLE 193 If your OBD system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update. A recheck with the above test routine may then indicate that the system is now ready.
MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. Engine Oil Checking Oil Level To assure proper lubrication of your vehicle’s engine, the engine oil must be maintained, at the correct level. Check the oil level at regular intervals, such as every fuel stop.
MAINTAINING YOUR VEHICLE 195 3.5L Engine Oil Dipstick The best time to check the oil level is about 5 minutes after a fully warmed up engine is shut off or before starting the engine after it has sat overnight.
MAINTAINING YOUR VEHICLE Checking the oil while the vehicle is on level ground also will improve the accuracy of the oil level readings. Maintain the oil level between the MIN and MAX markings on the dipstick. Adding one quart of oil when the reading is at the MIN mark will result in a MAX reading on these engines. 3.5L Engine Oil Fill 2.
MAINTAINING YOUR VEHICLE 197 Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. • Day or night temperatures are below 32°F (0°C) • Stop and go driving • Extensive engine idling • Driving in dusty conditions • Short trips of less than 10 miles (16.
MAINTAINING YOUR VEHICLE Engine Oil Selection For best performance and maximum protection under all types of operating conditions, we only recommend engine oils that are API Certified and meet the requirements of DaimlerChrysler’s Material Standard MS-6395. Use Mopar or an equivalent oil meeting the specification MS-6395. American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API).
MAINTAINING YOUR VEHICLE 199 SAE 5W-30 oil is preferred for use in 2.7L engines within the operating temperatures shown in the viscosity chart. You are highly encouraged to use SAE 5W-30 oils to aid in low temperature starting and for improved fuel economy. 3.5L Engine Oil Chart The proper SAE viscosity grade of engine oil should be selected based on the following recommendations and be within the operating temperature shown in the engine oil viscosity charts.
MAINTAINING YOUR VEHICLE dealer, service station, or governmental agency for advice on how and where used oil can be safely discarded in your area. and procedures shown in the Service Manual. See the Consumer Assistance section for information on ordering a Service Manual. Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Special tools are required to properly measure tension and to restore belt tension to factory specifications.
MAINTAINING YOUR VEHICLE 201 Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to seek service to assure proper catalyst operation and prevent possible catalyst damage. If the Malfunction Indicator light is flashing, immediate service is required. CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
MAINTAINING YOUR VEHICLE Engine Timing Belt Replace the engine timing belt at the intervals described in the appropriate maintenance schedule. Crankcase Emission Control System Proper operation of this system depends on freedom from sticking or plugging due to deposits. As vehicle mileage builds up, the PCV valve and passages may accumulate deposits. If a valve is not working properly, replace it with a new valve.
MAINTAINING YOUR VEHICLE 203 Maintenance-Free Battery The top of the MAINTENANCE-FREE battery is permanently sealed. You will never have to add water, nor is periodic maintenance required. NOTE: The battery is stored in a compartment in front of the tire in the right front fender and is accessible through the engine compartment. The tire and wheel need not be removed to access the battery. To access the battery: 1. Turn the steering wheel fully to the right.
MAINTAINING YOUR VEHICLE CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion. Apply grease to posts and clamps after tightening.
MAINTAINING YOUR VEHICLE 205 Refrigerant Recovery and Recycling The air conditioning system of your vehicle contains R-134a, a refrigerant that does not deplete the ozone layer in the upper atmosphere. The manufacturer recommends that air conditioning service be done by facilities using refrigerant recyling and recovery equipment that meets SAE standard J1991. Power Steering Fluid Check WARNING! Fluid level should be checked with the engine off to prevent injury from moving parts. Do not overfill.
MAINTAINING YOUR VEHICLE Fluid level should be maintained at the proper level indicated on the side of the reservoir. If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. See your dealer or the Recommended Fluids, Lubricants and Genuine Parts section in this manual for the correct power steering fluid for your vehicle. 3.5L Power Steering Reservoir 2.
MAINTAINING YOUR VEHICLE 207 Chassis Lubrication Front Suspension Ball Joints Inspect these ball joints whenever your vehicle is serviced. They are permanently lubricated and do not require periodic lubrication. Steering Linkage Inspect tie rod ends whenever the vehicle is serviced. They are permanently lubricated and do not require periodic lubrication. Drive Shaft Universal Joints Your vehicle has four constant velocity universal joints. Periodic lubrication of these joints is not required.
MAINTAINING YOUR VEHICLE External Lock Cylinders Lubricate the external lock cylinders twice a year, preferably in the fall and spring. Apply a small amount of lubricant, such as Mopar Lock Cylinder Lubricant directly into the lock cylinder (avoid excess lubricant). Insert the key into the lock cylinder and rotate from the unlocked to the locked position; without adding more lubricant. Repeat this procedure three or four times.
MAINTAINING YOUR VEHICLE 209 Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non abrasive cleaner. This will remove accumulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield.
MAINTAINING YOUR VEHICLE Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
MAINTAINING YOUR VEHICLE 211 Check the front of the radiator and condenser for any accumulation of bugs, leaves, etc. Clean the radiator and condenser by gently spraying water from a garden hose at the back of the core. coolant in open containers or allow it to remain in puddles on the ground. Prevent ingestion by animals or children. If ingested by a child, contact a physician immediately. Check the engine cooling system hoses for condition and tightness of connection.
MAINTAINING YOUR VEHICLE Higher concentrations (not to exceed 70%) may be used if temperatures below -37°F (-38°C) are anticipated. Use only high purity water such as distilled or deionized water when mixing the water/antifreeze solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. NOTE: Mixing coolant types will decrease the life of the engine coolant and will require more frequent engine coolant changes.
MAINTAINING YOUR VEHICLE 213 Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine Off and cold, the level of the coolant in the bottle should be between the MIN and MAX cold fill lines. Points to Remember NOTE: When the vehicle is stopped after a few miles of operation, you may observe vapor coming from the front of the engine compartment.
MAINTAINING YOUR VEHICLE • Maintain coolant concentration of a minimum of 50% ethylene glycol and high quality water with recommended antifreeze for proper corrosion protection of your engine cooling system that contains aluminum components. Pay particular attention to those hoses nearest to high heat sources such as the exhaust manifold. Inspect hose routing to be sure hoses do not touch any heat source or moving component that may cause heat damage or mechanical wear.
MAINTAINING YOUR VEHICLE 215 WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency. Brake and Power Steering System Hoses When servicing the vehicle for scheduled maintenance, inspect surface of hoses for evidence of heat and mechanical damage.
MAINTAINING YOUR VEHICLE Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning lamp shows system failure. Use only manufacturer’s recommended brake fluid. Refer to the Recommended Fluids, Lubricants and Genuine Parts section for the correct fluid type. Be sure to clean the top of the master cylinder area before removing the cap.
MAINTAINING YOUR VEHICLE 217 Fuel System Hoses Electronic Fuel Injection high pressure fuel systems are designed with hoses and clamps which have unique material characteristics to provide adequate sealing and resist attack by deteriorated gasoline. You are urged to use only manufacturer specified hoses and clamps, or their equivalent in material and specification, in any fuel system servicing. It is mandatory to replace all clamps that have been loosened or removed during service.
MAINTAINING YOUR VEHICLE Fluid Level Check The fluid level in the automatic transaxle should be checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly reduce the life of the transaxle and of the fluid. 3.5L Transmission Dipstick Procedure For Checking Fluid Level To properly check the automatic transaxle fluid level, the following procedure must be used: 2.7L Transmission Dipstick • The vehicle must be on level ground.
MAINTAINING YOUR VEHICLE 219 • Wipe the dipstick clean and reinsert until seated. Remove dipstick and note reading. • If the fluid is hot (180° F / 82° C) , the reading should be in the cross hatched area marked ”HOT” (between the upper two holes in the dipstick). • If the fluid is cold (80° F / 27° C) , the reading should be in the cross hatched area marked “COLD” (between the lower two holes in the dipstick).
MAINTAINING YOUR VEHICLE Appearance Care And Protection From Corrosion • Stone and gravel impact. Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
MAINTAINING YOUR VEHICLE 221 CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels and rear deck lid be kept clear and open.
MAINTAINING YOUR VEHICLE Use a mild soap and warm water solution to clean vinyl or leather upholstery. For stubborn stains, use Mopar Vinyl Cleaner. Mopar Vinyl Cleaner is specifically recommended for vinyl trim. WARNING! abrasive and damage the leather surface and should be removed immediately with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar Total Clean. Care should be taken to avoid soaking the leather with any liquid.
MAINTAINING YOUR VEHICLE 223 To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic.
MAINTAINING YOUR VEHICLE FUSES The fuse block is behind the end cover at the left side of the instrument panel. Pull the cover straight away from the instrument panel for access to the fuses. Fuse Block Relays The location and identification of fuse block relays can be found on the inside of the instrument panel end cover. Underhood Fuses A Power Distribution center is located in the engine compartment. This center contains fuses and relays for circuits that operate only under the hood.
MAINTAINING YOUR VEHICLE 225 CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it indicates a problem in the circuit that must be corrected.
MAINTAINING YOUR VEHICLE Cavity 18 19 20 21 22 23 24 25 Fuse 20 Amp Yellow 15 Amp Lt.
MAINTAINING YOUR VEHICLE 227 BULB REPLACEMENT Headlight, Parking Light Replacement 1. Open the hood. 2. Remove the upper crossmember attachments on both sides of the vehicle; 6 in total.
MAINTAINING YOUR VEHICLE 3. Remove the headlamp jackscrews on both sides of the vehicle. 4. Remove the windshield filler neck screw.
MAINTAINING YOUR VEHICLE 229 5. Remove the speed control servo screw. 6. Lift and prop the crossmember above the headlamp on the side being serviced, and remove the electrical connectors from the headlamp. 7. Pull headlamp up and under crossmember to remove it from the vehicle. 8. Remove the bulb retaining ring by turning it counterclockwise. Pull the bulb and socket assembly from the housing and pull the bulb from the socket. 9.
MAINTAINING YOUR VEHICLE 11. Reinstall the upper crossmember attachments, headlamp jackscrews, windshield filler neck screw and speed control servo screw. Fog Light Front Park and Turn Signal Light 1. Remove the headlight assembly from the vehicle. 2. Turn the park/turn signal bulb and socket assembly counterclockwise and remove it from the housing. 3. Pull the bulb from the socket and install a new bulb. 4. Reinstall the bulb and socket assembly. 5. Reinstall the headlight assembly.
MAINTAINING YOUR VEHICLE 231 5. Connect the wiring connector to the new bulb and reinstall the assembly. Center Stop Light 1. Open the trunk and reach up under the package shelf. Tail, Stop, Back Up, and Turn Signal Lights 1. Open the trunk and remove the fasteners securing the light housing to the body. 2. Pull the light housing from the body to expose the wiring socket. 7 2. Turn the bulb socket counterclockwise and remove it from the housing. 3. Pull the bulb from the socket and replace the bulb. 4.
MAINTAINING YOUR VEHICLE License Plate Light 1. Remove the screws securing the light to the rear fascia. 2. Remove the bulb and socket assembly and pull the bulb from the socket. 3. Replace the bulb and reinstall the bulb and socket assembly. 4. Reattach the light to the rear fascia.
MAINTAINING YOUR VEHICLE 233 FLUID CAPACITIES Fuel (Approximate) Engine Oil with Filter 2.7 & 3.5 Liter Engine Cooling System* 2.7 Liter Engine 3.5 Liter Engine * Includes heater and coolant recovery bottle filled to MAX level. U.S. 17 Gallons Metric 64 Liters 5 Qts 4.7 Liters 10.5 Qts 11 Qts 10 Liters 10.
MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Axle Differential (front-rear) Brake Master Cylinder Power Steering Reservoir Tire Pressure Fluid, Lubricant or Genuine Part Mopar威 ATF+4 Automatic Transmission Fluid. Mopar威 Hypoid Gear Lubricant (SAE 80W-90). Do not use synthetic gear lubricants. Mopar威 DOT-3 Brake Fluid. Mopar威 ATF+4 Automatic Transmission Fluid. Refer to label on driver’s door pillar.
䡵 Emission Control System Maintenance . . . . . . 236 M A I N T E N A N C ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 239 E 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . 236 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 236 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 237 M NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual. NOTE: Most vehicles are operated under the conditions listed for Schedule ⬙B⬙. Second is Schedule “A”. It is for vehicles that are not operated under any of the conditions listed under Schedule ⬙B⬙. Use the schedule that best describes your driving conditions.
M A I N T E N A N C E S C H E D U L E S 8 238 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check tire pressure and look for unusual wear or damage. • Change the engine oil filter. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of coolant reservoir, brake master cylinder, power steering and transaxle and add as needed. • Check all lights and all other electrical items for correct operation.
SCHEDULE “B” SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an 〫. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16.2 km).
M 240 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Inspect the air cleaner filter and replace if reN C quired.* E Replace the air cleaner filter. * S C H E D U L E S 8 Inspect the front and rear brake linings and rotors. Adjust the drive belt tension.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Adjust the drive belt tension. Check and replace, if necessary, the PCV valve.
M 242 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Inspect the air cleaner filter and replace if reN C quired.* E Replace the air cleaner filter. * S C H E D U L E S 8 Adjust the drive belt tension. Inspect the front and rear brake linings and rotors. Replace the differential fluid.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Replace the drive belts. Replace the power steering fluid. Check and replace, if necessary, the PCV valve. * ‡ Change the automatic transaxle fluid and filter.
M 244 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Inspect the air cleaner filter and replace if reN C quired.* E Replace the air cleaner filter. * S C H E D U L E S 8 Replace the air cleaner filter. Adjust the drive belt tension. Inspect the front and rear brake linings and rotors. Check and replace, if necessary, the PCV valve.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Flush and replace the engine coolant. Replace the engine timing belt (Federal Emissions). Replace the engine timing belt (California Emissions). Replace the spark plugs. Adjust the drive belt tension. Change the differential fluid.
M 246 SCHEDULE “A” A I SCHEDULE “A” N T Miles E N (Kilometers) A [Months] N C Change engine oil and engine oil filter. E Inspect the air cleaner filter and replace if reS C H E D U L E S 8 quired.* Replace the air cleaner filter. * Adjust the drive belt tension. Inspect the front and rear brake linings and rotors. Inspect and replace PCV valve if required.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. * Replace the drive belts. Inspect the front and rear brake linings and rotors. Flush and replace engine coolant at 60 months or 100,000 miles. Check and replace, if necessary, the PCV valve.
M 248 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Inspect the air cleaner filter and replace if reE quired.* S C H E D U L E S 8 78,000 (125 000) [78] X X Replace the air cleaner filter. * Adjust the drive belt tension. Inspect the front and rear brake linings and rotors. Replace the spark plugs. Check and replace, if necessary, the PCV valve. *‡ Replace the engine timing belt (Federal Emissions equipped vehicles only).
SCHEDULE “A” WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252 ▫ Prepare For The Appointment . . . . . . . . . . . . 252 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 252 䡵 Reporting Safety Defects . . . . . . . . . . . . . . . . . 255 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 255 䡵 Publication Order Forms . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE 253 • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center.
IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unexpected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands behind only the manufacturer’s Service Contracts. If you purchased a manufacturer’s Service Contract, you will receive Plan Provisions and an Owner Identification Card in the mail within three weeks of your vehicle delivery date.
IF YOU NEED CONSUMER ASSISTANCE 255 MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
PUBLICATION ORDER FORMS 9
IF YOU NEED CONSUMER ASSISTANCE 259 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car.
IF YOU NEED CONSUMER ASSISTANCE corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. WARNING! The temperature grade is established for a tire that is properly inflated and not overloaded.
INDEX 10
INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . 157 ABS (Anti-Lock Brake) System . . . . . . . . . . . . . 112 Accident Damage . . . . . . . . . . . . . . . . . . . . . . . 221 Adding Engine Coolant (Antifreeze) . . . . . . . . . 211 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 170 Air Cleaner, Engine . . . . . . . . . . . . . . . . . . . . . 202 Air Conditioning . . . . . . . . . . . . . . . . . . . . 137,140 Air Conditioning Controls . . . . . . . . . . . . .
INDEX 263 Saving Feature . . . . . . . . . . . . . . . . . . . . 65,66,68 Belts, Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 Belts, Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 202 Body Mechanism Lubrication . . . . . . . . . . . . . . 207 Brake, Parking . . . . . . . . . . . . . . . . . . . . . . . . . 156 Brake System . . . . . . . . . . . . . . . . . . . . . . . 157,214 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 157 Fluid Check . . . . . . . . . . .
INDEX Instrument Panel . . . . . . . . . . . . . . . . . . . . . 223 Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 Vinyl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 Waxing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 Windshield Wiper Blades . . . . . . . . . . . . . . . 209 Climate Control . . . . . . . . . .
INDEX 265 Disposal Antifreeze . . . . . . . . . . . . . . . . . . . . . . . . . . . 211 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 199 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . 14,15 Door Locks, Automatic . . . . . . . . . . . . . . . . . . . 16 Door Locks, Central . . . . . . . . . . . . . . . . . . . . . . 15 Door Opener, Garage . . . . . . . . . . . . . . . . . . . 76,81 Drive Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Flashers Hazard Warning . . . . . . . . . . . . . . . . . . . . . . 176 Flat Tire Changing . . . . . . . . . . . . . . . . . . . . . . 177 Floor Shift Interlock . . . . . . . . . . . . . . . . . . . . . . 13 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . 233 Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Fluid Level Checks . . . . . . . . . . . . . . . . . . . . . . 218 Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 267 Homelink Transmitter . . . . . . . . . . . . . . . . . . 76,81 Hood Release . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Hook, Coat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214,217 Key-In Reminder . . . . . . . . . . . . . . . . . . . . . . . . 12 Keyless Entry System . . . . . . . . . . . . . . . . . . . . . 18 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Knee Bolster . . . .
INDEX Dome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Door Ajar . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Exterior Check . . . . . . . . . . . . . . . . . . . . . . . . 50 Fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68,230 Front Replacement . . . . . . . . . . . . . . . . . . . . 226 Hazard Warning Flasher . . . . . . . . . . . . . . . . 176 Headlight Switch . . . . . . . . . . . . . . . . . . . . . . 66 Headlights . . . . . . . . . . . . . . . .
INDEX 269 Memory Feature . . . . . . . . . . . . . . . . . . . . . . 57,61 Memory Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Mini-Trip Computer . . . . . . . . . . . . . . . . . . . . . . 93 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Automatic Dimming . . . . . . . . . . . . . . . . . . . . 56 Electric Remote . . . . . . . . . . . . . . . . . . . . . . . 57 Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Outside . . . . . . . . . . . .
INDEX Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158 Steering, Checking . . . . . . . . . . . . . . . . . . . . 205 Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Trunk Lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Pregnant Women and Seat Belts . . . . . . . . . . . . . 32 Programmable Electronic Features .
INDEX 271 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 Glide-To-Exit . . . . . . . . . . . . . . . . . . . . . . . . . 60 Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . 61 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Reclining . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Sentry Key . . . .
INDEX Tilt Steering Column . . . . . . . . . . . . . . . . . . . . . 71 Time Delay, Headlight . . . . . . . . . . . . . . . . . . . . 67 Timing Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . 202 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 50,159,259 Air Pressure . . . . . . . . . . . . . . . . . . . . . . 159,161 Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . 167 Balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 Chains . . . . . . . . . . . .
INDEX 273 Trunk Release, Emergency . . . . . . . . . . . . . . . . . 26 Trunk Release Remote Control . . . . . . . . . . . . . . 25 Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . 68,110 Underhood Fuses . . . . . . . . . . . . . . . . . . . . . . Uniform Tire Quality Grades . . . . . . . . . . . . . Universal Joints . . . . . . . . . . . . . . . . . . . . . . . Universal Transmitter . . . . . . . . . . . . . . . . . . Vacuum/Vapor Harnesses . . Vehicle Identification Number Vehicle Loading .
