TABLE OF CONTENTS SECTION PAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1 1 INTRODUCTION 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4 UNDERSTANDING YOUR INSTRUMENT PANEL 5 STARTING AND OPERATING 6 WHAT TO DO IN EMERGENCIES 7 MAINTAINING YOUR VEHICLE 8 MAINTENANCE SCHEDULES 9 IF YOU NEED CONSUMER ASSISTANCE 10 INDEX . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS m Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m Vehicle Identification Number . . . . . . . . . . . . . . 6 m How To Use This Manual . . . . . . . . . . . . . . . . . 4 m Vehicle Modifications / Alterations . . . . . . . . . . 6 m Warnings And Cautions . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . . 9 ▫ Central Locking—If Equipped . . . . . . . . . . . . .13 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . . 9 ▫ Door Ajar Warning . . . . . . . . . . . . . . . . . . . . .14 ▫ Automatic Transaxle Ignition Interlock System . .10 ▫ Automatic (Rolling) Door Locks . . . . . . . . . . . .14 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ General Information . . . . . . . . . . . . . . . . . . . .18 ▫ Transmitter Battery Service . . . . . . . . . . . . . . .18 m Vehicle Theft Alarm . . . . . . . . . . . . . . . . . . . . .19 ▫ Tamper Alert . . . . . . . . . . . . . . . . . . . . . . . . .19 ▫ Security System Manual Override . . . . . . . . . . .20 m Trunk Lock And Release . . . . . . . . . . . . . . . . . .20 m Trunk Safety Warning . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS 9 Ignition Key Removal CAUTION! 2 An unlocked car is an invitation to thieves. Always remove the key from the ignition, lock the doors, and close the windows when leaving the vehicle unattended. Place the shift lever in PARK and make sure that the gearshift knob push button has returned to the out position. Turn the key to the Lock position and remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service. Automatic Transaxle Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK. It also prevents shifting out of PARK unless the key is in the OFF or RUN positions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 immobilized. If the Theft Alarm Light remains On during vehicle operation, it indicates a fault in the system electronics. Customer Key Programming You can program new keys to the system if you have two valid keys by doing the following: All of the keys provided with your new vehicle have been programmed to the vehicle electronics. 1. Insert the first valid key into the ignition and turn the ignition On for at least 3 seconds but no longer than 15 seconds.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information The Sentry Key system complies with FCC rules part 15. Operation is subject to the following two conditions: 1. this device may not cause harmful interference 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Power Door Locks There is a door lock switch on each front door located to the front of each door handle. Press this switch to lock or unlock the doors. 2 If the door lock plunger is down when you shut the door, the door will lock. Therefore, make sure that the keys are not inside the vehicle before closing the door. If you press the door lock switch while the keys are in the ignition switch, and the driver’s door is open, the doors will not lock.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Door Ajar Warning If you move the vehicle and a door is not completely closed, the word DOOR will replace the odometer display and a chime will sound once. The odometer display will reappear once the door is closed. Automatic (Rolling) Door Locks The doors will lock automatically, as programmed from the factory, if: 1. The transaxle is in gear, 2. All doors are closed, 3. Vehicle speed is above 15 mph (24 km/h), 4. The accelerator pedal is depressed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Depress the power door lock switch to lock the doors. 15 1. Close all doors and place the key in the ignition. 2. Cycle the ignition switch between OFF and ON/RUN and back to OFF 4 times ending up in the OFF position. 3. Depress the power door lock switch to unlock the doors. 4. A single chime will indicate the completion of the programming. 4. A single chime will indicate the completion of the programming.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To unlock the doors: Press and release the UNLOCK button once to unlock the driver’s door. Press the button twice within 5 seconds to unlock all doors. If your vehicle is equipped with Illuminated Entry, the interior lights also come on and remain on for about 30 seconds, when you unlock the doors. 1. Press and hold the Lock button on the transmitter. NOTE: The system may be programmed to unlock all the doors upon the first press of the Unlock button.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To unlock the trunk: Press and hold the Trunk button on the transmitter to unlatch the trunk. NOTE: The transmitter can be programmed to unlatch the trunk immediately upon activation of the Trunk button (without pressing and holding) by performing the following procedure: 1. Press and hold the Unlock button on the transmitter. 2. Continue to hold the Unlock button, wait at least 4 but no longer than 10 seconds, then press the Trunk button. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Press and release the Lock and Unlock buttons simultaneously, followed by a press and release of ANY button on each new transmitter to be programmed as well as the original transmitter. You will hear a chime when a transmitter has been successfully programmed. You will have 30 seconds to finish programming all new transmitters. A chime will sound when the 30 seconds is over or the ignition switch is turned to the LOCK position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch the battery, clean it with rubbing alcohol. 3. Reassemble the transmitter case. Snap the halves together and test transmitter operation. VEHICLE THEFT ALARM The system monitors the doors, trunk, and ignition for unauthorized operation. If something triggers the alarm, the system will signal for up to 18 minutes.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Security System Manual Override The system will not arm if you lock the doors using the manual lock control. TRUNK LOCK AND RELEASE operate. Vehicles with manual transmissions must have the ignition ON and be at 0 mph for the switch to work. With the ignition ON, the word “deck” will be displayed in place of the odometer display indicating that the trunk is open. The odometer display will reappear once the trunk is closed or if the trip button is depressed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Trunk Internal Emergency Release 21 POWER WINDOWS 2 NOTE: As a security measure, a Trunk Internal Emergency Release lever is built into the trunk latching mechanism. In the event of an individual being locked inside the trunk, the trunk can be simply opened by pulling on the glow-in-the-dark handle attached to the trunk latching mechanism. See picture. The window controls on the driver’s door operate all windows.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belts All seating positions in your vehicle are equipped with Lap/Shoulder Belts. The belt webbing retractor is designed to lock during very sudden stops or impacts. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the belt will lock and reduce your risk of striking the inside of the vehicle or being thrown out. 23 WARNING! • Wearing a seat belt incorrectly is dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the front seat. 2. The seat belt latch plate is on the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a ”click.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is very dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your dealer and have it fixed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The pretensioners are triggered by the front airbag control module (see Airbag Section). Like the front airbags, the pretensioners are single use items. After a collision that is severe enough to deploy the airbags and pretensioners, both must be replaced.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Turn off the engine. A single chime will sound to signify that you have successfully completed the programming. The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver’s seat belt remains unbuckled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver and Right Front Passenger Supplemental Restraint System (SRS) - Airbag This vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s airbag is mounted in the center of the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly. seat as far back as possible, and use the proper child restraint. See the section on “Child Restraint”. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 2. You should read the instructions provided with your child restraint to make sure that you are using it properly. 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag System Components The front airbag system consists of the following: • Airbag Control Module • AIRBAG Readiness Light • Driver Airbag • Passenger Airbag • Steering Wheel and Column • Instrument Panel • Interconnecting Wiring • Knee Impact Bolsters 31 How The Airbag System Works • The front airbag control module determines if a frontal collision is severe enough to require the airbags to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The airbag control module also turns on the AIRBAG light in the instrument panel for 6 to 8 seconds when the ignition is first turned on, then turns the light off. If it detects a malfunction in any part of the system, it turns on the light either momentarily or continuously. WARNING! Ignoring the AIRBAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and right front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or frame.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children 12 years and under should ride properly buckled up in a rear seat. According to crash statistics, children are safer when properly restrained in the rear seat rather than in the front. WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward facing infant restraint should only be used in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system. (See the LATCH — Child Seat Anchorage System Section.) The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE connection to the top tether anchorages have been available for some time. For some older child restraints, many child restraint manufacturers offer add-on tether strap kits or retro-fit kits. You are urged to take advantage of all the available attachments provided with your child restraint in any vehicle. child in a car seat. (Symbol shown to the left). Install your child seat as per child seat manufacturer recommendations.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provided with the child restraint system. The rear seat lower anchorages are round bars, located at the rear of the seat cushion where it meets the seat back, and are just visible when you lean into the rear seat to install the child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing Child Restraints Using the Vehicle Seat Belts The passenger seat belts are equipped with cinching latch plates which are designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip. Pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Attach the tether strap hook (A) of the child restraint to the anchor and remove slack in the tether strap (B) according to the child restraint manufacturer’s instructions. 41 WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS The engine in your new vehicle does not require a long break-in period. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration, within the limits of local traffic laws, contributes to a good break-in. Wide open throttle acceleration in low gear can be detrimental and should be avoided.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE must remain open, close all windows. Adjust the heating or cooling system to force outside air into the vehicle. Set the blower at high speed. Safety Checks You Should Make Inside the Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 m Convertible Top Operation . . . . . . . . . . . . . . . .47 ▫ Illuminated Vanity Mirrors . . . . . . . . . . . . . . . .58 ▫ To Lower The Top . . . . . . . . . . . . . . . . . . . . . .47 m Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 ▫ To Raise The Top . . . . . . . . . . . . . . . . . . . . . .49 ▫ Manual Front Seat Adjustments . . . . . . . . . . . .58 ▫ Top Cover Installation . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . . .64 m Electronic Speed Control— If Equipped . . . . . .70 ▫ Multi-Function Control Lever . . . . . . . . . . . . . .66 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . . .71 ▫ Headlights, Parking Lights, Instrument Panel Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 ▫ To Set At A Desired Speed . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONVERTIBLE TOP OPERATION WARNING! The convertible top does not provide the structural protection that a reinforced metal roof does, and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision. Therefore it is important that all occupants wear their seat belts at all times when riding in a convertible.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Release the top from the windshield header by pulling both latch handles rearward until the latch hooks are free. and holding the switch in the second detent position will lower all four windows and the top to the full down position. 4. Press the Power Top Switch to disengage the top pins from the header. As soon as the top is free, close both latch handles. CAUTION! NOTE: The Power Top Switch has two detent positions for lowering the convertible top.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Raise The Top: 49 CAUTION! CAUTION! To insure no damage occurs to the visors, they should be rotated to the forward (against glass) position prior to raising or lowering the convertible top. To fully insure that no damage occurs, be sure that the vehicle is at a complete stop with the gear selector in the Park position before lowering or raising the top. 1. Remove the top cover and store it in the trunk. 2. Turn the ignition to the ON position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Top Cover Installation With the top down and the convertible top latch handles in the closed position, there are two ways to install the convertible top cover. Lay the unfolded convertible top cover across the convertible top and choose the way that suits you best. Installation From Inside The Vehicle 1. Kneel on the rear seat and tuck the rear edge and side edges of the top cover under the black molding near the trunk.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Insert both tabs located on the front of the top cover in between the seatback and seatback bracket. 51 3. Snap the top cover flaps to the inner trim panel snaps. The side of the seat back cushion hides the snap.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Press down on the forward portion of the top cover to engage the hook and loop fasteners. Installation From Outside The Vehicle 1. Start on one side of the vehicle and tuck as much of the top cover as possible under the black molding.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Snap the top cover flap to the inner trim panel snap. (The side of the seat back cushion hides the snap.) 53 3. Tuck the top cover tab closest to you into the space between the seatback and the seatback bracket. 3 4. Walk to the other side of the vehicle and finish tucking the top cover under the black molding. Insert the remaining tab between the seatback and the seatback bracket.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Snap the remaining top cover flap to the inner trim panel snap. 6. Press down on the forward portion of the top cover to engage the hook and loop fasteners. Top Cover Removal Unsnap the snaps and disengage the hook and loop fasteners, slide the tabs from the rear seat and then from the rear of the top storage area. Remove the top cover, fold, and store in the trunk or a dry secure area.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES The front console has two cup holders. An optional removable ashtray may be located in the driver’s side cup holder. 55 The center console/armrest has a pencil /tire gage holder and a tissue holder mounted on the underside of the cover. The bottom of the console bin also has built in holders for compact discs or cassette tapes. The power outlet is also mounted inside the center console (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror — If Equipped Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustment. If the driver’s sunvisor interferes with the mirror, the mirror can be moved to the right to eliminate the interference. Automatic Dimming Mirror — If Equipped This mirror will automatically adjust for annoying headlight glare from vehicles behind you.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Exterior Mirrors Folding Feature — If Equipped Both mirrors have hinges and can be folded either forward or rearward to resist damage. Electric Remote-Control Mirrors Both of the outside mirrors can be adjusted by using the remote controls mounted on the instrument panel located to the left of the steering wheel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirrors An illuminated vanity mirror is on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on automatically. Closing the mirror cover turns off the lights. SEATS Manual Front Seat Adjustments Forward/Rearward — If Equipped The adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Bucket Seats The recliner control is on the side of the seat. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever. To return the seat to the upright position, lean forward slightly before lifting the lever, then lean forward to the desired position and release the lever. 59 WARNING! • Adjusting a seat while the vehicle is moving is dangerous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Driver’s Seat The power seat switches are on the outboard side of the seat, near the floor. Use the forward switch to move the front of the seat cushion up and down. Use the rear switch to move the rear of the seat cushion up and down. The middle switch will move either the entire seat forward and rearward or the seat cushion up and down. The rear lever controls the seatback reclining angle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The left rotary switch controls the heat level for the driver’s seat, and the right rotary switch controls the heat level for the passenger’s seat. These switches feature several heat settings ranging from 0 to 6. To Fold The Front Seatback Forward: Turn the high mounted release lever rearward and fold the seatback forward. If you release the lever early, a safety feature locks the seat into that position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjust the restraints so that the upper edge is as high as practical. To raise, pull up on the head restraint. To lower, depress the button on the post guide and push down on the head restraint. TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then lift the secondary latch located under the front edge of the hood, near the center and raise the hood. 63 To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. WARNING! If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Front Map/Reading Lights These lights, located under the rearview mirror, come on whenever a door is opened or the illuminated entry system is activated. The lights can also be turned on with the doors closed by means of switches located on the front of the rearview mirror. NOTE: The map lights will remain on until the mirror switches have been turned to the OFF position, so be sure that they have been turned off before leaving the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE turn on the lights. Turn the panel dimmer switch fully clockwise to prevent the lights from coming on when a door is opened. NOTE: The interior lights have a “fade to off” feature. When the lights are turned off, they gradually “fade” off. 65 Interior light Defeat (OFF) Rotate the dimmer control to the extreme bottom full-circle position. The interior lights will remain off when the doors are open.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multi-Function Control Lever The Multi-Function lever controls the operation of the headlights, turn signals, headlight beam select switch, instrument panel light dimming, passing light, dome light, and fog lights. Headlights, Parking Lights, Instrument Panel Lights Turn the end of the control lever to the first detent for parking light operation. Turn to the second detent for headlight operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE until the ignition switch is turned OFF or the parking brake is engaged. The headlight switch must be used for normal night time driving. Lights-on Reminder If the headlights or parking lights are on after the ignition is turned off, a chime will sound when the driver’s door is opened. Fog Lights — If Equipped The fog light switch is in the multi-function lever. To activate the fog lights, turn on the low beam headlights and pull out the end of the control lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch in the right side control lever. Turn the end of the control lever to select the desired wiper speed. delay range, the wiper will operate for several cycles after the lever is released, and then resume the intermittent interval previously selected. If the lever is pulled while in the OFF position, the wipers will operate for several cycles, then turn OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 Speed Sensitive Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. Turn the lever to the delay position, then select the delay interval. The delay can be regulated from a maximum of approximately 18 seconds between cycles, to a cycle every 1/2 second. 3 NOTE: The wiper delay times depend on vehicle speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TRACTION CONTROL— IF EQUIPPED To turn the Traction Control System Off, press the switch located on the top of the steering column, to the right of the hazard switch, until the Traction Control indicator in the instrument cluster lights up. To turn the Traction Control System On, press the switch until the Traction Control indicator in the instrument cluster turns off. NOTE: The Traction Control System is enabled each time the ignition switch is turned On.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 To Activate: Press the ON/OFF switch to turn the speed control system ON. To turn the system OFF, press the ON/OFF switch again. The system should be turned OFF when not in use. The CRUISE Indicator in the instrument cluster will light up when the Speed Control is ON. To Deactivate: A soft tap on the brake pedal, pushing the CANCEL button, or normal brake or clutch pressure will deactivate speed control without erasing the memory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To decrease speed while speed control is Engaged, press and hold the COAST button. Releasing the button when the desired speed is reached, will establish a new SET speed. Tapping the COAST button once will result in a 1 mph (1.6 km/h) decrease in the SET speed. Each time the button is tapped, the SET speed decreases. For example, tapping the button three times will decrease speed by 3 mph (5 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rolling Hills The transaxle may downshift into third gear and remain there as the vehicle travels over rolling hills. The transaxle will upshift into fourth gear when the road flattens out. The transaxle will resume its normal shift schedule if you depress the accelerator pedal during any of the above conditions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features it could cause injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Choose one of the three Universal Transceiver buttons to program. Place the hand held controller one to three inches from the Universal Transceiver while keeping its indicator light in view. 75 5. The indicator light in the Universal Transceiver will begin to flash, first slowly and then rapidly. The rapid flashing indicates successful programming.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE On garage door openers with the “Rolling Code” feature, the transmitter code changes after each use to prevent the copying of your code. difficulty in locating the training button, check your garage door opener manual, or call 1-800-355-3515 or, on the Internet, at www.homelink.com. To check if your device is protected by a “Rolling Code” system: 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Canadian Programming/Gate Programming Canadian frequency laws, and the technology of some entry gates, require you to press and release the hand held transmitter button every two seconds during programming Continue to press and hold the Universal Transceiver button while you press and release the hand held transmitter button until the frequency signal has been learned.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. HomeLinkt is a trademark owned by Johnson Controls, Inc.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS m Instruments And Controls . . . . . . . . . . . . . . . . .83 ▫ To Set The Clock . . . . . . . . . . . . . . . . . . . . . . .96 m Instrument Cluster Standard . . . . . . . . . . . . . . .84 m Radio General Information . . . . . . . . . . . . . . . .96 m Instrument Cluster Premium . . . . . . . . . . . . . . .85 ▫ Radio Broadcast Signals . . . . . . . . . . . . . . . . . .96 m Instrument Cluster – GTC Model . . . . . . . . . . .86 ▫ Two Types Of Signals .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Seek Button (Radio Mode) . . . . . . . . . . . . . . . .98 ▫ Changing Tape Direction . . . . . . . . . . . . . . . . 101 ▫ Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 ▫ Metal Tape Selection . . . . . . . . . . . . . . . . . . . 101 ▫ PTY (Program Type) Button . . . . . . . . . . . . . . .98 ▫ Pinch Roller Release . . . . . . . . . . . . . . . . . . . 101 ▫ Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL m Sales Code RBB—AM/FM Stereo Radio With Cassette Tape Player And CD Changer Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 ▫ Operating Instructions . . . . . . . . . . . . . . . . . . 105 ▫ Power Button . . . . . . . . . . . . . . . . . . . . . . . . 106 ▫ Electronic Volume Control . . . . . . . . . . . . . . . 106 81 ▫ Radio Display Messages . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Program Button 5 . . . . . . . . . . . . . . . . . . . . . 117 ▫ Tape Player . . . . . . . . . . . . . . . . . . . . . . . . . 119 ▫ Time Button . . . . . . . . . . . . . . . . . . . . . . . . . 117 ▫ CD Player — Single Disc In Radio . . . . . . . . . 119 ▫ Changing Modes . . . . . . . . . . . . . . . . . . . . . . 117 ▫ CD Player — 6 Disc CD Changer . . . . . . . . . . 119 ▫ Removing Discs From The CD Changer . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 83 INSTRUMENTS AND CONTROLS 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER STANDARD
UNDERSTANDING YOUR INSTRUMENT PANEL 85 INSTRUMENT CLUSTER PREMIUM 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER – GTC MODEL
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gauge When the ignition key is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Traction Control — If Equipped This display indicator illuminates momentarily as a bulb check when the ignition switch is first turned ON. The indicator will blink during an active traction event, but will remain solid when the system is deactivated or if a system malfunction occurs.
UNDERSTANDING YOUR INSTRUMENT PANEL range. Before reaching the red area (over 6,500 rpm), ease up on the accelerator to prevent engine over speed. 6. Turn Signal Indicators The arrows will flash in unison with the exterior turn signal, when using the turn signal lever. 7. High Beam Indicator This light shows that the headlights are on high beam. Pull the turn signal lever toward the steering wheel to switch the headlights from high or low beam. 8.
UNDERSTANDING YOUR INSTRUMENT PANEL The Malfunction Indicator Light flashes to alert to serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced as soon as possible if this occurs. 11. Fog Light Indicator — If Equipped This light shows when the fog lights are ON. 12. Temperature Gauge The temperature gauge shows engine coolant temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined. The trip odometer shows individual trip mileage. To switch from odometer to trip odometer, press and release the Trip Odometer button. Press and release the Trip button a second time to return to the odometer. While in trip mode, press and hold the button for at least 1⁄2 second to reset the trip odometer.
UNDERSTANDING YOUR INSTRUMENT PANEL The light does not show the quantity of oil in the engine. This can be determined using the procedure shown in Section 7. 18. Brake System Warning Light This light monitors both the brake fluid level and the parking brake. If the light comes on, it indicates either that the parking brake is on or there is a low fluid level in the brake master cylinder. On vehicles equipped with Anti-lock (ABS), the brake light may also indicate reduced braking performance.
UNDERSTANDING YOUR INSTRUMENT PANEL remain on continuously. Refer to 9Enhanced Driver Seat Belt Reminder System (BeltAlert™)9 in the Occupant Restraints section for more information. COMPASS, TEMPERATURE, AND TRIP COMPUTER DISPLAY — IF EQUIPPED 20. Theft Alarm Light — If Equipped The light in the instrument cluster will flash rapidly for 15 seconds. This shows that the system is arming. If the light comes on but does not flash, the system is still armed, but there is a problem in the trunk circuit.
UNDERSTANDING YOUR INSTRUMENT PANEL Reset The following trip conditions can be reset: • AVG ECO (changes to present fuel economy) • ODO • ET To reset only the trip condition currently displayed, press and release the STEP and US/M buttons simultaneously until a chime sounds. To reset all trip conditions, hold down the STEP and US/M buttons simultaneously (about 2 seconds) until a second chime sounds and then release the buttons.
UNDERSTANDING YOUR INSTRUMENT PANEL Compass Temperature Display This display provides the outside temperature and one of eight compass readings to indicate the direction the vehicle is facing. WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible personal injury or property damage.
UNDERSTANDING YOUR INSTRUMENT PANEL 95 When the CAL indicator goes off, the compass is calibrated and should display correct headings. Verify proper calibration by checking North (N), South (S), East (E), and West (W). If the compass does not appear accurate, repeat the calibration procedure in another area. Compass Variance Variance is the difference between magnetic North and geographic North. For proper compass function, the correct variance zone must be set.
UNDERSTANDING YOUR INSTRUMENT PANEL Outside Temperature If the outside temperature is more than 131°F (55°C), the display will show 131°F. When the outside temperature is less than 240°F (240°C), the display will show 240°F/C. To Set The Clock: CIGAR LIGHTER/ASHTRAY For a nominal charge your dealer can provide a “smoker’s” package. This package consists of a cigar lighter and an ashtray that utilizes one of the cup holders. 2. Press any other button to exit from the clock setting mode.
UNDERSTANDING YOUR INSTRUMENT PANEL Two Types of Signals There are two basic types of radio signals... AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary... and FM or Frequency Modulation, in which the frequency of the wave is varied to carry the sound. Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception.
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Button (Radio Mode) Press and release the Seek button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. Holding the button will by pass stations until you release the button. Tuning Press the TUNE control up or down to increase or decrease the frequency. If you press and hold the button, the radio will continue to tune until you release the button.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Soft Rhythm and Blues Sports Talk Top 40 Weather Radio Display Soft R&B Sports Talk Top 40 Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station.
UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received. Scan Button Pressing the SCAN button causes the tuner to search for the next station, in either AM or FM, pausing for 5 seconds at each listenable station before continuing to the next. Pressing the AM/FM button continues the search in the alternate frequency band.
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Button Press the SEEK button up for the next selection on the tape and down to return to the beginning of the current selection. Press the SEEK button up or down to move the track number to skip forward or backward 1 to 6 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc. Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing.
UNDERSTANDING YOUR INSTRUMENT PANEL Noise Reduction The Dolby Noise Reduction System* is on whenever the tape player is on, but may be switched off. To turn off the Dolby Noise reduction System: Press the Dolby button (button 2) after you insert the tape. The NR light in the display will go off when the Dolby System is off. The Dolby System is automatically reactivated each time a tape is inserted. * ”Dolby” noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
UNDERSTANDING YOUR INSTRUMENT PANEL • If you insert a disc with the ignition ON and the radio OFF, the CD will automatically be pulled into the CD Player and the display will show the time of day. If you insert a disc with the ignition OFF, the display will show the time of day for about 5 seconds, then go out. Seek Button Press the top of the SEEK button for the next selection on the CD.
UNDERSTANDING YOUR INSTRUMENT PANEL To select Satellite Radio (if equipped), press the MODE button until the word SIRIUS appears. The following will be displayed in this order: After three seconds, the current channel name and number will be displayed for five seconds. The current program type and channel number will then be displayed for five seconds. The current channel name and number will then be displayed until an action occurs.
UNDERSTANDING YOUR INSTRUMENT PANEL Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an interesting change of pace. • Disc inserted upside down Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer. SALES CODE RBB—AM/FM STEREO RADIO WITH CASSETTE TAPE PLAYER AND CD CHANGER CAPABILITY CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: When first learning the control functions, the user should set the controls as shown in the following list. Tone Controls…As illustrated. Speaker Control…Centered. Power Button The volume control/power button pops out when pressed, this turns the sound system ON in the mode last used. Pushing the button back in turns the sound system OFF.
UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice.
UNDERSTANDING YOUR INSTRUMENT PANEL Cassette Player Features With ignition OFF and the sound system OFF, you can eject the tape cassette by pushing the EJECT button. You can turn the tape player ON by inserting a cassette or activating the MODE button (with a cassette in the radio), but only when the ignition and radio are on. Each time a cassette is inserted the tape player will begin playing on the side of the cassette that is facing up in the player.
UNDERSTANDING YOUR INSTRUMENT PANEL NR (Noise Reduction) Pushing the Number 2 Pre-set button when a tape is playing deactivates the Dolby Noise Reduction System*. When Dolby is ON, the NR symbol appears on the display. Each time a tape is inserted the Dolby will turn ON. * “Dolby” noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. Dolby and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
UNDERSTANDING YOUR INSTRUMENT PANEL CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically. As a safeguard and to protect your CD player, one of the following warning symbols may appear on your display. A CD HOT symbol indicates the player is too hot. CD HOT will pause the operation. Play can be resumed when the operating temperature is corrected or another MODE is selected.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS 111 Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button in will bypass stations without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL Bass and Treble Tone Control The tone controls consist of 2 separate bands. The bass band is on the left, and the treble band is on the right. Each band is adjusted by a slider control with a detent at the mid-position. Moving the control up or down increases or decreases amplification of that band. The mid position provides a balanced output. AM/FM Selection Press the AM/FM button to change from AM to FM.
UNDERSTANDING YOUR INSTRUMENT PANEL CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. Inserting The Compact Disc CAUTION! This CD player will accept 4 3⁄4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. 113 Seek Press the top of the SEEK button for the next selection on the CD.
UNDERSTANDING YOUR INSTRUMENT PANEL Press the SEEK button to move to the next randomly selected track. Press the RND (button 4) button a second time to stop Random Play. Mode Press the MODE button repeatedly to select between the CD player, the optional remote CD changer and the Satellite Radio (if equipped). When Satellite Radio (if equipped) is selected “SA” will appear in your radio display. A CD or tape may remain in the player while in the Satellite mode.
UNDERSTANDING YOUR INSTRUMENT PANEL Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer. CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically. As a safeguard and to protect your CD player, one of the following warning symbols may appear on your display. A CD HOT symbol indicates the player is too hot.
UNDERSTANDING YOUR INSTRUMENT PANEL 6 DISC CD CHANGER — IF EQUIPPED The CD changer is located below the radio in the instrument panel. The changer plays only 4 3⁄4 inch (12 cm) discs. The changer holds up to 6 discs. Each disc is loaded and ejected through a single slot in front of the changer. Each disc has a numbered button with an amber light above it which, when illuminated, indicates that a disc is loaded in that particular chamber.
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Button Press the top of this button on the radio once to play the next track. Press the bottom of the button once to return to the beginning of the current track. Press the bottom of the button twice to play the previous track. FF/TUNE/RW Press the FF (fast forward) button and the CD player will fast forward through the tracks until the button is released. Press the RW (rewind) button and the CD player will reverse through the tracks until the button is released.
UNDERSTANDING YOUR INSTRUMENT PANEL • Pressing the AM/FM button while in the tape or CD mode will select the radio mode. • If in the CD mode and the last CD is ejected, the radio will tune to the last station selected. REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches.
UNDERSTANDING YOUR INSTRUMENT PANEL Pressing the center button will make the radio switch between the various modes available (AM/FM/TAPE/ CD, Etc.). The left hand control is a rocker type switch with a push-button in the center. The function of the left hand control is different depending on which mode you are in. The following describes the left hand control operation in each mode.
UNDERSTANDING YOUR INSTRUMENT PANEL If you press the switch up or down twice it plays the second track, three times, it will play the third, etc. The button in the center of the left hand switch will cause the CD changer to play the next available disc. CASSETTE TAPE AND PLAYER MAINTENANCE To keep the cassette tapes and player in good condition, take the following precautions: 1. Do not use cassette tapes longer than C-90; otherwise, sound quality and tape durability will be greatly diminished. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL COMPACT DISC MAINTENANCE To keep the compact discs in good condition, take the following precautions: 1. Handle the disc by its edge or center; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6.
UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS Manual Air Conditioning/Heater Control The Air Conditioning System allows you to balance the temperature, amount, and direction of air circulating throughout the vehicle. The air conditioning system of your vehicle contains R-134a, a refrigerant that does not deplete the ozone layer in the upper atmosphere.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If your air conditioning performance seems lower than expected, check the front of the air conditioning condenser for an accumulation of dirt or insects. The air conditioning condenser is located in front of the radiator. Clean with a gentle water spray from behind the radiator and through the condenser. Fabric front fascia protectors may reduce air flow to the condenser, reducing air conditioning performance.
UNDERSTANDING YOUR INSTRUMENT PANEL • Panel Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct air flow. • Bi-Level Air is directed through the instrument panel and floor outlets. NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The defroster turns off automatically after 15 minutes of operation. Each later activation will allow 10 minutes of operation. Side Window Demisters A side window demister outlet is at each end of the instrument panel. These non-adjustable outlets direct air toward the side windows when the system is in either the FLOOR, MIX, or DEFROST modes. A small amount of air is directed to the side window demisters in BI-LEVEL mode as well.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips (Manual A/C Control Only)
UNDERSTANDING YOUR INSTRUMENT PANEL 127 Outside Air Intake When operating the system during the winter months, make sure the air intake, directly in front of the windshield, is free of ice, slush, snow or other obstructions such as leaves. Leaves collected in the air-intake plenum may reduce air flow and plug the plenum water drains.
STARTING AND OPERATING CONTENTS m Starting Procedures . . . . . . . . . . . . . . . . . . . . 132 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . . 132 ▫ Manual Transaxle . . . . . . . . . . . . . . . . . . . . . 132 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 132 ▫ Extreme Cold Weather (Below -20°F Or -29°C) . . . . . . . . . . . . . . . . . 133 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . . 134 ▫ After Starting . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING ▫ Anti-Lock Brake System (ABS) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 m Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 143 m Traction Control — If Equipped . . . . . . . . . . . 144 m Tire Safety Information . . . . . . . . . . . . . . . . . . 145 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 145 ▫ Tire Identification Number (TIN) . . . . . . . . . . 148 ▫ Tire Loading And Tire Pressure . . . . . . . . . . .
STARTING AND OPERATING 131 m Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 166 ▫ Selection Of Engine Oil . . . . . . . . . . . . . . . . . 169 ▫ Warranty Requirements . . . . . . . . . . . . . . . . . 166 ▫ Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 m Flexible Fuel – (2.7L Engines With Automatic Transmission Only) . . . . . . . . . . . . . . . . . . . . . 168 ▫ Cruising Range . . . . . . . . . . . . . . . . . . . . . . . 170 ▫ E-85 General Information . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust temperatures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. WARNING! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death.
STARTING AND OPERATING 133 CAUTION! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from another vehicle. This type of start can be dangerous if done improperly, so follow the procedure carefully.
STARTING AND OPERATING If Engine Fails to Start If the engine fails to start after you have followed the “NORMAL STARTING” or “EXTREME COLD WEATHER” procedures, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine. This should clear any excess fuel in case the engine is flooded. CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again.
STARTING AND OPERATING 135 WARNING! WARNING! Remember to disconnect the cord before driving. Damage to the 110-115 volt AC electrical cord could cause electrocution. Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle you should shift the transmission into Park, remove the key from the ignition, and apply the park brake.
STARTING AND OPERATING CAUTION! WARNING! Damage to the transaxle may occur if the following precautions are not observed: It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something.
STARTING AND OPERATING Four Speed Automatic Transaxle The electronically controlled transaxle provides a precise shift schedule. The transaxle electronics are self calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few shift cycles. Reset Mode The transaxle is monitored electronically for abnormal conditions.
STARTING AND OPERATING WARNING! Your vehicle could move and injure you and others if it is not completely in P (Park). Check by trying to move the gearshift lever back and forth without depressing the shift button after you have set it in P. Make sure it is in Park before leaving the vehicle. WARNING! Never use the Park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.
STARTING AND OPERATING NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance, fuel economy, and extend transaxle life by reducing excessive shifting and heat build up. Use the “3” range when descending steep grades to prevent brake system distress. “L” Low This range should be used for maximum engine braking when descending steep grades.
STARTING AND OPERATING NOTE: During cold weather, until the transaxle lubricant has warmed, you may have difficulty shifting. This is normal and not harmful to the transaxle. Recommended Shift Speeds To use your manual transaxle for both fuel economy and performance, it should be upshifted as listed. Shift at the vehicle speeds listed for acceleration. Earlier upshifts during cruise conditions (relatively steady speeds) will result in increased fuel economy, and may be used as indicated.
STARTING AND OPERATING PARKING BRAKE When the parking brake is applied with the ignition on, the brake light in the instrument cluster will come on. NOTE: This light only shows that the parking brake is on. It does not show the degree of brake application. 141 When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the transmission locking mechanism may make it difficult to move the selector out of Park.
STARTING AND OPERATING BRAKE SYSTEM Your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be much greater than that required with the power system operating. WARNING! Riding the brakes can lead to brake failure and possibly an accident.
STARTING AND OPERATING WARNING! • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING TRACTION CONTROL — IF EQUIPPED The system is always in the “stand by” mode unless: • The Traction Control switch has been used to turn the system off; • There is an Anti-Lock Brake or Traction System malfunction; • The system has been deactivated to prevent damage to the brake system due to overheated brake temperatures. NOTE: Extended heavy use of Traction Control may cause the system to deactivate and turn on the Traction Control indicator located in the instrument cluster.
STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings 145 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter 9P9 is absent from this tire size designation. Example: 215/65R15 96H • LT(Light Truck)-Metric tire sizing is based on U.S. design standards.
STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards (....blank....( = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING 147 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (ie. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure 149 Tire and Loading Information Placard Tire Placard Location NOTE: Some vehicles have a “Tire and Loading Information” placard located on the driver’s side “B” pillar. 5 This placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires.
STARTING AND OPERATING adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual. NOTE: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWR’s) for the front and rear axles must not be exceeded. For further information on GAWR’s, vehicle loading and trailer towing, see the Vehicle Loading section of this manual.
STARTING AND OPERATING 151 NOTE: For the following example the combined weight of occupants and cargo should never exceed 865 lbs. (392 Kg).
STARTING AND OPERATING WARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 1.
STARTING AND OPERATING 153 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3. Ride Comfort and Vehicle Stability— Proper tire inflation contributes to a comfortable ride. Overinflation produces a jarring and uncomfortable ride.
STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1mile (1 km) after a 3 hour period.
STARTING AND OPERATING WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). 155 Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
STARTING AND OPERATING Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 35 mph (55 km/h). Do not install more than one compact spare tire/wheel on the vehicle at any given time. See the paragraph on Freeing A Stuck Vehicle in Section 6 of this manual.
STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point.
STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING 159 TIRE CHAINS Due to limited clearance, tire chains are not recommended. Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). CAUTION! Tire Rotation Recommendations Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving and braking functions.
STARTING AND OPERATING Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permissible if desired. The suggested rotation method is the “forward-cross” shown in the diagram. AUTOSTICK — IF EQUIPPED Autostick is a driver-interactive transaxle that offers manual gear shifting capability to provide you with more control.
STARTING AND OPERATING autostick lever to the AUTOSTICK position. The transaxle will remain in the current gear until an upshift or downshift is chosen. 161 • Downshifts from third to second gear above 66 mph (106 km/h) and from second to first gear above 37 mph (60 km/h) will be ignored. • You can start out in first, second, or third gear. Shifting into fourth gear can occur only after vehicle speed reaches 15 mph (24 km/h).
STARTING AND OPERATING FUEL REQUIREMENTS Your vehicle is designed to meet all emission regulations and provide excellent fuel economy when using high quality regular unleaded gasoline with an octane rating of 87. The use of premium gasoline is not recommended. The use of premium gasoline will provide no benefit over high quality regular gasolines, and in some circumstances, may result in poorer performance. Light spark knock at low engine speeds is not harmful to your engine.
STARTING AND OPERATING CAUTION! DO NOT use gasolines containing Methanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components. Problems that result from using methanol/gasoline blends are not the responsibility of the manufacturer and may not be covered by the vehicle warranty. While MTBE is an oxygenate made from Methanol, it does not have the negative effects of Methanol.
STARTING AND OPERATING Malfunction Indicator Light to illuminate. The manufacturer recommends that you try a different brand of unleaded gasoline having lower sulfur to determine if the problem is fuel related prior to returning your vehicle to an authorized dealer for service. ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door, on the driver’s side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle.
STARTING AND OPERATING NOTE: Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is properly tightened. The Malfunction Indicator Light will come on if the gas cap is not properly secured. Make sure that the gas cap is tightened each time the vehicle is refueled. NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full. NOTE: The fuel tank filler tube may have a restricting door about 50 mm (2 inches) down from the opening.
STARTING AND OPERATING VEHICLE LOADING • The weight of any other type of cargo or equipment put in or on your vehicle. Vehicle Loading Capacities Front Seat Occupants . . . . . . . . . . . . . . . . . . . . . . . 2 Rear Seat Occupants . . . . . . . . . . . . . . . . . . . . . . . . 2 Luggage . . . . . . . . . . . . . . . . . . . . . . 115 lbs. (52 kg) Rated Vehicle Capacity. . . . . . . . . . . . 715 lbs. (324 kg) • Remember that everything put in or on the trailer adds to the load on your vehicle.
STARTING AND OPERATING • The “D” range can be selected when towing. However, if frquent shifting occurs while in this range, the “3” range must be selected. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance and extend tranaxle life by reducing excessive shifting and heat build up. WARNING! Connecting trailer brakes to your vehicle’s hydraulic brake lines can overload your brake system and cause it to fail.
STARTING AND OPERATING FLEXIBLE FUEL – (2.7L Engines with Automatic Transmission Only) E-85 General Information The information in this section is for Flexible Fuel vehicles only. These vehicles can be identified by the unique fuel filler door label that states Ethanol (E-85) or Unleaded Gasoline Only. This section only covers those subjects that are unique to these vehicles.
STARTING AND OPERATING 169 • you operate the vehicle immediately after refueling for a period of at least 5 minutes American Petroleum Institute (API) Engine Oil Identification Symbol Observing these precautions will avoid possible hard starting and/or significant deterioration in drivability during warm up. This symbol means that the oil has been certified by the American Petroleum Institute (API).
STARTING AND OPERATING • Engine Oil Selection for Operating on E-85 If you operate the vehicle on E-85 fuel, either full or part-time, use only Mopar Flexible Fuel 5W-30 engine oil (P/N 4318086) or an equivalent that meets the Manufacturer’s Standard MS-9214. Equivalent commercial Flexible Fuel engine oils may be labeled as Flexible Fuel (FFV) or Alternate Fuel (AFV). These engine oils may be satisfactory if they meet the Manufacturer’s Standard.
STARTING AND OPERATING 171 Replacement Parts Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol compatible parts. Maintenance If you operate the vehicle using E-85 fuel, follow Schedule B in the maintenance schedule section of this manual. CAUTION! Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect driveability.
WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Flasher . . . . . . . . . . . . . . . . . 174 m Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 185 m If Your Engine Overheats . . . . . . . . . . . . . . . . 174 m Towing A Disabled Vehicle . . . . . . . . . . . . . . . 185 m Jacking And Tire Changing . . . . . . . . . . . . . . . 176 m Towing This Vehicle Behind Another Vehicle (Flat Towing With All Four Wheels On The Ground) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and the vehicle locked. NOTE: With extended use, the flasher may wear down your battery. IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. • On the highways — Slow down.
WHAT TO DO IN EMERGENCIES the fan control to High. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle. Idle the vehicle in Park with the air conditioner turned off until the pointer drops back into the normal range.
WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • Do not attempt to change a tire on the side of the vehicle close to moving traffic.
WHAT TO DO IN EMERGENCIES 177 1. Block wheel diagonally opposite flat tire. 2. Remove the spare tire, scissors jack and lug wrench from stowage.
WHAT TO DO IN EMERGENCIES 3. Before raising the vehicle, use lug wrench to carefully pry off wheel cover (if equipped with steel wheels) or center cap (if equipped with aluminum wheels). Loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. WARNING! To avoid possible personal injury, handle the wheel covers with care to avoid contact with the metal edges and retention teeth. 4.
WHAT TO DO IN EMERGENCIES 179 6
WHAT TO DO IN EMERGENCIES WARNING! WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. 6. Remove lug nuts and tire. 7. Mount spare tire. 8. Tighten all lug nuts on mounting studs. 9.
WHAT TO DO IN EMERGENCIES JUMP-STARTING THE BATTERY WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from another vehicle.
WHAT TO DO IN EMERGENCIES WARNING! WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and person injury could result. Do not connect the cable to the negative post of the discharged battery. The resulting electrical spark could cause the battery to explode. During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump starting because the battery could rupture or explode.
WHAT TO DO IN EMERGENCIES 183 WARNING! WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other.
WHAT TO DO IN EMERGENCIES DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the front wheels to pull erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels, particularly with high output engines. WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels.
WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE If your vehicle is equipped with Traction Control, turn the system off before attempting to “rock” the vehicle. If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth between Reverse and First gear.
WHAT TO DO IN EMERGENCIES TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the ground) Automatic Transaxle Your vehicle may be towed under the following conditions: The gear selector must be in NEUTRAL, the distance to be towed must not exceed 15 miles (25 km), and the towing speed must not exceed 25 mph (40 km/h).
MAINTAINING YOUR VEHICLE CONTENTS m 2.4L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 189 ▫ Power Steering Fluid Check . . . . . . . . . . . . . . 202 m 2.7L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 190 ▫ Suspension Ball Joints . . . . . . . . . . . . . . . . . . 203 m Onboard Diagnostic System — OBD II . . . . . . 191 ▫ Body Mechanism Lubrication . . . . . . . . . . . . . 203 m Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 ▫ Headlight Bulb Replacement . . . . . . . . . . . . . 226 m Convertible Top Care . . . . . . . . . . . . . . . . . . . 221 ▫ Park, Turn Signal, Sidemarker Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 228 ▫ Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 ▫ Fog Light Bulb Replacement . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 189 2.
MAINTAINING YOUR VEHICLE 2.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing.
MAINTAINING YOUR VEHICLE If your OBD system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update. A recheck with the above test routine may then indicate that the system is now ready.
MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle.
MAINTAINING YOUR VEHICLE 195 • Stop and Go driving • Extensive engine idling. • Driving in dusty conditions • Short trips of less than 10 miles (16.2 km) • More than 50% of your driving is at sustained high speeds during hot weather, above 90° F (32° C) • Trailer towing • Taxi, Police or delivery service (commercial service) CAUTION! Overfilling or underfilling will cause aeration or loss of oil pressure. This could damage your engine.
MAINTAINING YOUR VEHICLE NOTE: Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or 6 months whichever comes first. Engine Oil Selection For best performance and maximum protection under all types of operating conditions,we recommend engine oils that are API Certified and meet the requirements of DaimlerChrysler’s Material Standard MS-6395. Use Mopar or an equivalent oil meeting the specification MS6395.
MAINTAINING YOUR VEHICLE may be labeled as Flexible Fuel (FFV) or Alternate Fuel (AFV). These engine oils may be satisfactory if they meet the manufacturer’s standard. CAUTION! If Flexible Fuel engine oil is not used when using E-85, engine wear may be increased significantly. This may void your warranty. Synthetic Engine Oils There are a growing number of engine oils being promoted as either synthetic or semi-synthetic.
MAINTAINING YOUR VEHICLE Drive Belts — Check Condition and Tension At the mileage shown in the maintenance schedules, check all drive belts for condition and proper tension. Improper belt tension can cause belt slippage and failure. Inspect the drive belts for evidence of cuts, cracks, or glazing and replace them if there is any sign of damage which could result in belt failure. If adjustment is required, adjust the belts according to the specifications and procedures shown in the Service Manual.
MAINTAINING YOUR VEHICLE Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly serviced to assure proper catalyst operation and prevent possible catalyst damage.
MAINTAINING YOUR VEHICLE • Do not idle the engine with any spark plug wires disconnected for prolonged period. Engine Timing Belt Replace the engine timing belt (2.4L Only) at the intervals described in the appropriate maintenance schedule. NOTE: The battery is stored in a compartment behind the left front fender and is accessible without removing the tire and wheel. Remote battery terminals are located in the engine compartment for jump starting.
MAINTAINING YOUR VEHICLE 201 WARNING! CAUTION! Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling. Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Battery gas is flammable and explosive.
MAINTAINING YOUR VEHICLE through the condenser as required. Fabric front fascia protectors may reduce air flow to the condenser, reducing air conditioning performance. WARNING! The air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced repairman.
MAINTAINING YOUR VEHICLE 203 Body Mechanism Lubrication Locks and all body pivot points, including such items as seat tracks, doors,liftgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed.
MAINTAINING YOUR VEHICLE Multi-Purpose Lubricant, NLGI Grade 2, should be applied sparingly to all pivot and sliding contact areas. External Lock Cylinders Lubricate the external lock cylinders twice a year, preferably in the fall and spring. Apply a small amount of lubricant, such as Mopar Lock Cylinder Lubricant directly into the lock cylinder (avoid excess lubricant). Insert the key into the lock cylinder and rotate from the unlocked to the locked position; without adding more lubricant.
MAINTAINING YOUR VEHICLE Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non abrasive cleaner. This will remove accumulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield.
MAINTAINING YOUR VEHICLE WARNING! WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, follow the preceding safety tips.
MAINTAINING YOUR VEHICLE 207 dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Cooling System Inspection WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition key to the OFF position. The fan is controlled by both the temperature of the engine cooling system and the pressure in the air conditioning system and can start at any time the ignition key is in the ON position.
MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. The first change should not be required until 5 years or 100,000 miles (160,000 km), whichever comes first. The coolant should be flushed and changed every two years or 36,000 miles (57,600 km) thereafter. If the solution is dirty and contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner.
MAINTAINING YOUR VEHICLE Coolant Pressure Cap The cap must be fully tightened to prevent loss of coolant, and to insure that coolant will return to the radiator from the coolant reserve tank. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. WARNING! The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add coolant when the engine is overheated.
MAINTAINING YOUR VEHICLE over time. This is normal. If the coolant level is hard to see, jostling the coolant bottle will make it easier to see. There is no need to remove the radiator cap unless checking for coolant freeze point, adding, or replacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. Heater performance may also be adversely affected by low coolant levels.
MAINTAINING YOUR VEHICLE ONLY the correct type thermostat. Other designs may result in unsatisfactory cooling performance, poor gas mileage, and increased emissions. Hoses and Vacuum/Vapor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage. Hard or soft spots, brittle rubber, cracking, checking, tears, cuts, abrasions, and excessive swelling indicate deterioration of the rubber.
MAINTAINING YOUR VEHICLE Inspect all hose clamps and couplings to make sure they are secure and no leaks are present. Insure nylon tubing in these areas has not melted or collapsed. Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning lamp shows system failure.
MAINTAINING YOUR VEHICLE Use only manufacturer’s recommended brake fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. WARNING! Use of a brake fluid that has a lower initial boiling point than MOPAR DOT 3 Brake Fluid or that is unidentified as to DOT FMVSS specification may result in sudden brake failure during hard or prolonged braking. You could have an accident.
MAINTAINING YOUR VEHICLE Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission performance. Use only manufacturers recommended transmission fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid.
MAINTAINING YOUR VEHICLE 215 • If the fluid is hot (180°F / 82°C), the reading should be in the cross hatched area marked ”HOT” (between the upper two holes in the dipstick). Maintenance schedule “B” — Every 60,000 miles (96 000 km) change fluid and filter under the following conditions: • If the fluid level shows low, add sufficient transmission fluid to bring to the proper level.
MAINTAINING YOUR VEHICLE Manual Transaxle Use only the manufacturer’s recommended transmission fluid for the manual transaxle, NV-T350 or NV-T850, in your vehicle. Refer to Recommended Fluids, Lubricants and Genuine Parts section for correct fluid type. If it becomes necessary to top off or replace completely, this fluid should be used. The fill plug for the NV-T850 is located on the aluminum rear end cover. point not more than 4.0 mm below the bottom of the hole.
MAINTAINING YOUR VEHICLE 217 The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. • Use Mopar auto polish to remove road film and stains and to polish your vehicle. Take care never to scratch the paint. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.
MAINTAINING YOUR VEHICLE • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • Use Mopar touch up paint on scratches or chips as soon as possible. Your dealer has touch up paint to match the color of your vehicle. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible.
MAINTAINING YOUR VEHICLE Do not use cleaners, conditioners and protectants containing silicon or bleach as these may cause gloss level increases and/or discoloration. You should not increase the gloss level, especially on top of the instrument panel top surface. Higher gloss levels will increase the reflectivity in the windshield that could decrease visibility under bright light driving conditions. WARNING! Do not use volatile solvents for cleaning purposes.
MAINTAINING YOUR VEHICLE Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses.
MAINTAINING YOUR VEHICLE CONVERTIBLE TOP CARE Immediate removal of any contaminant is recommended. Regular washing of the top will enhance its life and appearance, and make successive cleanings easier. Do not subject the top to excessive heat. Frequently vacuum the top and storage compartment. Washing Hand washing is highly recommended. Automatic car washing equipment can damage the top material. If you must use an automatic car wash, soft cloth systems are preferred.
MAINTAINING YOUR VEHICLE Vacuuming the top with a wet/dry shop vacuum will decrease the top’s drying time, ensure removal of all dirt, and delete streaks in the material. Multiple cleanings may be necessary to remove stubborn stains. If stains persist, contact your local dealership for further suggestions. Cloth Top Protection For appearance purposes, you may wish to protect your Twillfast™ (cloth) top periodically. A fabric protectant such as Scotchguardt is suggested.
MAINTAINING YOUR VEHICLE FUSES Underhood Fuses (Power Distribution Center) 223 A Power Distribution Center is located in the engine compartment, near the air cleaner. This information applies to vehicles built without the fuse and relay numbering embossed on the Power Distributuion Center Top Cover. Interior Fuses 7 The fuse access panel is behind the end cover at the left side of the instrument panel. To remove the panel, pull it out, as shown.
MAINTAINING YOUR VEHICLE Cavity Fuse Circuit 1 30 Amp Green Blower Motor 2 10 Amp Red Right High Beam Headlight, High Beam Indicator 3 10 Amp Red Left High Beam Headlight 4 15 Amp Blue Power Door Lock Switch Illumination, Power Top Switch, Transmission Range Switch, Daytime Running Light Module (Canada), Power Windows, Anti-lock Brake System Module 5 10 Amp Red Power Door Lock and Door Lock Arm/Disarm Switches, Vanity, Reading, Map, Rear Seating, Ignition, and Trunk Lights, Illuminated Entry, Radio, P
MAINTAINING YOUR VEHICLE CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it shows a problem in the circuit that must be corrected. REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Bulb Number Instrument Cluster . . . . . . . . . . . . . . . . . . . . . PC 194 ABS Indicator . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE BULB REPLACEMENT Headlight Bulb Replacement 1. Open the hood and remove the two headlight mounting screws. 2. Remove the push-in fasteners by prying under the head of the fasteners with a flat bladed tool.
MAINTAINING YOUR VEHICLE 227 3. Gently pry the headlight assembly away from the fender as shown in the picture. This will free the ball stud from its retainer in the fender. Pull the headlight assembly away from the vehicle. 5. Pull the bulb out of the socket and replace the bulb. CAUTION! 4. Turn the retaining ring counterclockwise and remove the bulb and socket assembly. Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. 6.
MAINTAINING YOUR VEHICLE 7. Reinsert the bulb and socket assembly and turn the retaining ring clockwise to secure the bulb. 8. Reinstall the headlight assembly. Park, Turn Signal, Sidemarker Bulb Replacement 1. Open the hood and remove the two headlight assembly mounting screws. Pull the headlight assembly away from the vehicle. 2. Gently pry the headlight assembly away from the fender as shown in the picture. This will free the ball stud from its retainer in the fender.
MAINTAINING YOUR VEHICLE 3. Turn the bulb socket counterclockwise and remove the bulb and socket assembly. 229 Fog Light Bulb Replacement 1. Remove the screw securing the light assembly to the front fascia. 7 4. Pull the bulb out of the socket, replace the bulb, and reinstall the bulb and socket to the headlight assembly. Reinstall the headlight assembly. 2. Pull the bulb and socket assembly away from the vehicle to expose the bulb and socket assembly. 3.
MAINTAINING YOUR VEHICLE 4. Turn the bulb and socket assembly counterclockwise to remove it from the housing. 5. Install the new bulb and socket assembly, reattach the wiring connector, and reinstall the fog light assembly. Center Stoplight Bulb Replacement You may wish to see your dealer for service of this light. A detailed service procedure is contained in the manufacturer’s Service Manual. Information on purchasing a Service Manual can be found at the back of this Owner’s Manual.
MAINTAINING YOUR VEHICLE 231 License Plate Bulb Replacement 1. Locate both small slots on the outboard side of the license lamp. Using a small screwdriver, remove the entire housing. 2. Turn the bulb socket counterclockwise to remove it from the housing. Pull the bulb out of the socket. Replace the bulb and snap it back into place on the housing of the chrome appliqué. 2. Disconnect the wiring connector as shown and remove the plastic retainers. Remove the light housing from the vehicle. 3.
MAINTAINING YOUR VEHICLE Headlight Aiming The headlights on your new vehicle were aimed at the factory. The factory setting was made at a no load setting. A great increase in weight will change the aiming and it may be necessary to readjust the headlights if carrying an excessive amount of weight in the trunk, rear seats or pulling a trailer. To readjust the headlights first mark the position of the headlights on a wall prior to loading the vehicle.
MAINTAINING YOUR VEHICLE 233 RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Spark Plugs Oil Filter (2.4L Engine) Oil Filter (2.7L Engine) Fuel Selection Fluid, Lubricant, or Genuine Part Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) Use API Certified (GF-3). Refer to oil viscosity chart for correct SAE grade. Refer to the Vehicle Emission Control Information label under the engine hood.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E m Emission Control System Maintenance . . . . . . 236 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 239 m Maintenance Schedules . . . . . . . . . . . . . . . . . . 236 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 236 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES • Taxi, police, or delivery service (commercial service).L • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5,000 km) or 3 months, whichever comes first and follow schedule B of the “Maintenance Schedules” section of this manual. NOTE: Most vehicles are operated under the conditions listed for Schedule 9B9. Second is Schedule “A”.
M 238 MAINTENANCE SCHEDULES A I At Each Stop for Fuel N T • Check the engine oil level about 5 minutes after a fully E warmed engine is shut off. Checking the oil level while N A the vehicle is on level ground will improve the accuN racy of the oil level reading. Add oil only when the C level is at or below the ADD or MIN mark. E S C H E D U L E S 8 • Check the windshield washer solvent and add if required. Once a Month • Check tire pressure and look for unusual wear or damage.
SCHEDULE “B” SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an L. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16.2 km).
M 240 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Inspect the air cleaner filter and replace if N C necessary.* E Inspect the front and rear brake pads, linings, S C H E D U L E S 8 rotors, rear drums and shoes.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if required. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Check and replace, if necessary, the PCV valve. * Replace the spark plugs on 2.4 liter engine.
M 242 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Inspect the air cleaner filter and replace if N C necessary.* E Inspect the front and rear brake pads, linings, S C H E D U L E S 8 rotors, rear drums and shoes.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if necessary.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if required. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the ignition cables on 2.4 liter engine. Replace the accessory drive belts on the 2.7 liter engine. Replace the spark plugs on the 2.4 liter engine.
M 244 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Inspect the air cleaner filter and replace if N C necessary.* E Replace the air cleaner filter. * S C H E D U L E S 8 Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if required. Replace the engine timing belt on 2.4 liter engine. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.4 liter engine.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if necessary.* Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Flush and replace the engine coolant. Replace the spark plugs on the 2.7 liter engine. Check and retension accessory drive belts on 2.7 liter engine. Replace the accessory drive belts on 2.4 liter engine.
M 246 SCHEDULE “A” A I SCHEDULE “A” N T Miles E N (Kilometers) A [Months] N C Change engine oil and engine oil filter. E Inspect the air cleaner filter and replace if S C H E D U L E S 8 necessary.* Replace the air cleaner filter. * Replace the spark plugs on 2.4 liter engine. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Inspect and replace PCV valve if required.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. * Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if required. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.4 liter engine. Flush and replace engine coolant at 60 months or 100,000 miles. Check and replace, if necessary, the PCV valve.
M 248 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Inspect the air cleaner filter and replace if reE quired.* S C H E D U L E S 8 78,000 (125 000) [78] X X Replace the air cleaner filter. * Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.4 liter engine. Replace the spark plugs on 2.7 liter engine. Check and replace, if necessary, the PCV valve. *‡ Replace the engine timing belt on 2.
SCHEDULE “A” WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252 ▫ Prepare For The Appointment . . . . . . . . . . . . 252 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 252 m Reporting Safety Defects . . . . . . . . . . . . . . . . . 255 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 255 m Publication Order Forms . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center.
IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unexpected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands behind only the manufacturer’s Service Contracts. If you purchased a manufacturer’s Service Contract, you will receive Plan Provisions and an Owner Identification Card in the mail within three weeks of your vehicle delivery date.
IF YOU NEED CONSUMER ASSISTANCE MOPART PARTS Mopart fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
IF YOU NEED CONSUMER ASSISTANCE • Service Manuals. These comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing and repairing DaimlerChrysler Corporation vehicles. A complete working knowledge of the vehicle, system and/or components is written in straightforward language with illustrations, diagrams and charts. • Diagnostic Procedure Manuals.
IF YOU NEED CONSUMER ASSISTANCE 257 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car.
IF YOU NEED CONSUMER ASSISTANCE corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. WARNING! The temperature grade is established for a tire that is properly inflated and not overloaded.
INDEX 10
INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . 142 Adding Engine Coolant (Antifreeze) . . . . . . . . . 208 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 164 Aiming Headlights . . . . . . . . . . . . . . . . . . . . . . 232 Air Cleaner, Engine . . . . . . . . . . . . . . . . . . . . . 198 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . 122 Air Conditioning, Operating Tips . . . . . . . . . . . 126 Air Conditioning Refrigerant . . . . . . . . . . .
INDEX Location . . . . . . . . . . . . . . . . . . . . . . . . . 181,200 Belts, Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 Belts, Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 200 Body Mechanism Lubrication . . . . . . . . . . . . . . 203 Boot, Convertible Top . . . . . . . . . . . . . . . . . . . . 50 B-Pillar Location . . . . . . . . . . . . . . . . . . . . . . . 149 Brake, Parking . . . . . . . . . . . . . . . . . . . . . . . . . 141 Brake System . . . . . . . . . . . .
INDEX Compact Disc Player . . . . . . . . . . . . . . . . . . 97,102 Compact Spare Tire . . . . . . . . . . . . . . . . . . . . . 155 Compass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Compass Calibration . . . . . . . . . . . . . . . . . . . . . 94 Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Contract, Service . . . . . . . . . . . . . . . . . . . . . . . 254 Convertible . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Convertible Boot . . . .
INDEX Driving On Slippery Surfaces . . . . . . . . . . . . . . . . . . 184 Electrical Outlet, Auxiliary . . . . . . . . . . . . . . . . . 78 Electronic Speed Control . . . . . . . . . . . . . . . . . . 70 Emergency Brake . . . . . . . . . . . . . . . . . . . . . . . 141 Emergency, In Case of Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 Emergency Trunk Release . . . . . . . . . . . . . . . 20,21 Emission Control System Maintenance . . . . 192,236 Engine . . . . . . . . . . . . . .
INDEX Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . 232 Fog Light Service . . . . . . . . . . . . . . . . . . . . . . . 229 Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 67,229 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . 185 Fuel Adding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 Filler Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 Gauge . . . . .
INDEX Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . 12 Immobilizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . . 35 Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . 56 Instrument Cluster . . . . . . . . . . . . . . . . . . 84,85,86 Instrument Panel and Controls . . . . . . . . . . . . . . 83 Instrument Panel Cover . . . . . . . . . . . . . . . . . . 220 Instrument Panel Lens Cleaning . . . . . . .
INDEX Oil Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Rear Servicing . . . . . . . . . . . . . . . . . . . . . . . 230 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . 91 Security Alarm . . . . . . . . . . . . . . . . . . . . . . . . 19 Service . . . . . . . . . .
INDEX Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . 194,232 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232 Change Interval . . . . . . . . . . . . . . . . . . . . . . 195 Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 Identification Logo . . . . . . . . . . . . . . . . . 169,196 Materials Added to . . . . . . .
INDEX Recommended Fluids, Lubricants and Genuine Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233 Reformulated Gasoline . . . . . . . . . . . . . . . . . . . 162 Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202 Reminder, Seat Belt . . . . . . . . . . . . . . . . . . . . . . 27 Remote Keyless Entry . . . . . . . . . . . . . . . . . . . . 15 Remote Trunk Release . . . . . . . . . . . . . . . . . . . . 20 Replacement Tires . . . . . . . . . . . . . . . . . .
INDEX Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 Cold Weather . . . . . . . . . . . . . . . . . . . . . . . . 133 Engine Fails to Start . . . . . . . . . . . . . . . . . . . 134 Steering Power . . . . . . . . . . . . . . . . . . . . . . . . . . . 143,202 Tilt Column . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Steering Wheel Mounted Sound System Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 Stuck, Freeing . . . . . . . . . . . . . . . . . . . .
INDEX Traction Control . . . . . . . . . . . . . . . . . . . . 70,87,144 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . 166 Minimum Requirements . . . . . . . . . . . . . . . . 166 Trailer and Tongue Weight . . . . . . . . . . . . . . 166 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Transaxle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 Additives . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 Automatic . . . . . . . . . . . . . . . .
INDEX Windows Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Windshield Washers . . . . . . . . . . . . . . . . . . . 68,205 271 Windshield Wipers . . . . . . . . . . . . . . . . . . . . 68,205 Wiper Blade Replacement . . . . . . . . . . . . . . . . . 205 Wipers, Intermittent . . . . . . . . . . . . . . . . . . . . . .
