SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications / Alterations . . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS 1 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . .11 ▫ Manual Door Locks . . . . . . . . . . . . . . . . . . . . .16 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .11 ▫ Power Door Locks . . . . . . . . . . . . . . . . . . . . .17 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .12 ▫ Child Protection Door Lock . . . . . . . . . . . . . . .19 䡵 Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Turn Off “Flash Lights On Lock/Unlock” . . .23 ▫ General Information . . . . . . . . . . . . . . . . . . . .23 ▫ Transmitter Battery Service . . . . . . . . . . . . . . .24 䡵 Vehicle Theft Alarm . . . . . . . . . . . . . . . . . . . . . .25 䡵 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 ▫ Power Liftgate — If Equipped . . . . . . . . . . . . .28 䡵 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS You can insert the double sided keys into the locks with either side up. 11 be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place. Ignition Key Removal The shift lever must be in PARK. Turn the key to the LOCK position, then remove the key. Vehicle Key The dealer that sold you your new vehicle has the key code numbers for your vehicle locks.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The power window switches, radio, power sunroof, and power outlets will remain active for up to 45 seconds after the ignition switch has been turned off. Opening either front door will cancel this feature. CAUTION! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended. WARNING! Leaving children in a vehicle unattended is dangerous for a number of reasons.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE chip (transponder) embedded into them. Only keys that have been programmed to the vehicle can be used to start and operate the vehicle. The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regardless of whether or not the vehicle is locked or unlocked.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE All of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle. At the time of purchase, the original owner is provided with a four digit PIN number. This number is required for dealer replacement of keys.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. General Information The Sentry Key system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: The new Sentry Key has been programmed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS Manual Door Locks Lock the doors by pushing up on the lock knob on each door trim panel. If the lock knob is up when you shut the door, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door. WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. 17 locks will not operate. This prevents you from accidentally locking your keys in the vehicle. Removing the key or closing the door will allow the locks to operate. A chime will sound if the key is in the ignition and a door is open, as a reminder to remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Close all doors and place the key in the ignition switch. 2. Cycle the ignition switch ON/OFF four times ending in the OFF position. (do not start the engine) 3. Within 10 seconds of the final cycle, press the interior driver’s door lock switch to the LOCK position. 4. A single chime will sound to signify that you have successfully completed the programming.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. A single chime will sound to signify that you have successfully completed the programming. The Auto Unlock On Exit feature is enabled when your vehicle is shipped from the assembly plant and can be enabled or disabled by performing the procedure in the Electronic Vehicle Information Center (EVIC), Customer Programmable Features section or by repeating the above mentioned procedure.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To activate the system, open the rear door and move the child lock control, located near the door’s rear latch, to the ON position. REMOTE KEYLESS ENTRY This system allows you to lock or unlock the doors and liftgate, and activate the panic alarm from distances up to about 23 feet (7 meters) using a hand held radio transmitter. The transmitter need not be pointed at the vehicle to activate the system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 NOTE: If desired, the “Remote Unlock Driver’s Door 1st” feature can be turned on and off by referring to the Customer Programmable Features of the “Electronic Vehicle Information Center (EVIC)” section or by following these steps. 1. Press the UNLOCK button for 4 to 10 seconds. 2. While the UNLOCK button is pressed, (after 4 seconds) press the LOCK button. Release both buttons.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Customer Programmable Features of the “Electronic Vehicle Information Center (EVIC)” section or by following these steps. 1. Press the LOCK button for 4 to 10 seconds. 2. While the LOCK button is pressed (after 4 seconds), press the PANIC button. Release both buttons. The “Sound Horn On Lock” feature can be reactivated by repeating this procedure.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE to manually access the liftgate area. The liftgate will re-lock automatically within 10 seconds once the liftgate is closed. To Turn Off “Flash Lights On Lock/Unlock” NOTE: If desired, the “Flash Lights On Lock/Unlock” feature can be turned on and off by referring to the Customer Programmable Features of the “Electronic Vehicle Information Center (EVIC)” section or by following these steps. 1. Press the LOCK button for 4 to 10 seconds. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If your Remote Keyless Entry transmitter fails to operate from a normal distance, check for these two conditions. 1. A weak battery in the transmitter. The expected life of the battery is a minimum of three years. 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios. Transmitter Battery Service The recommended replacement battery is one CR2032 battery.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. To reassemble the transmitter case, snap the two halves together. Make sure there is an even “gap” between the two halves. Test transmitter operation. VEHICLE THEFT ALARM This system monitors the vehicle doors and ignition switch for unauthorized entry or operation. When the alarm is activated, the system provides both audible and visual signals.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To disarm the system: Press the UNLOCK button on the keyless entry transmitter. Also, using a valid sentry key and moving the ignition switch to the ON/START position will disarm the system. If you disarm the system and access the liftgate area, the system must be rearmed, as described previously, when closing the liftgate. If something has triggered the system in your absence, the horn will sound three times when you disarm the system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 The alarm system will be activated when the battery is connected if the system was previously armed. The exterior lights will flash, the horn will sound, and the ignition will not start the vehicle. If this occurs, disarm the system. 2 LIFTGATE The liftgate can be unlocked using the remote keyless entry or by activating the power door lock switches located on the front doors. Once unlocked, the liftgate can be opened or closed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • In the event of a power malfunction to the liftgate, an emergency liftgate latch release can be used to open the liftgate. The emergency liftgate latch release can be accessed through a snap-in cover located on the liftgate trim panel. liftgate is fully open, pressing the button twice within five seconds a second time will close the liftgate. The power liftgate may also be opened by pressing the switch located on the overhead console.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear. Make sure the liftgate is closed and latched before driving away. NOTE: • If anything obstructs the power liftgate while it is closing or opening, the liftgate will automatically reverse to the closed or open position, provided it meets sufficient resistance. • There are also pinch sensors attached to the side of the liftgate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and must be opened or closed manually. WARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 When the lock switch is pressed the window controls on the passenger doors will not illuminate and the passenger windows will be disabled. Auto Down Feature All the power window switches have an auto down feature. Press the window switch to the second detent, release, and the window will go down automatically. To open the window part way, press the window switch to the first detent and release it when you want the window to stop.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The front airbags have a multi stage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity. Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out. WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2 2. The seat belt latch plate is near the seatback of the front seats and next to your arm in the rear seats. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”. Latch Plate To Buckle WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. 37 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! Adjustable Upper Shoulder Belt Anchorage In the front seats, the shoulder belt anchorage can be adjusted upward or downward to help position the belt away from your neck.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. 39 2 Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. Sliding The Latch Plate 4. Continue to slide the latch plate up until it clears the folded webbing. Creating A Fold 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners are designed to work for all size occupants.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or RUN position. DaimlerChrysler does not recommend deactivating the Enhanced Warning System (BeltAlert). 1. Turn the ignition switch to the OFF position and buckle the driver’s seat belt. 4. Turn off the engine. A single chime will sound to signify that you have successfully completed the programming.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver and Front Passenger Supplemental Restraint System - Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Also, the front passenger airbag is certified to the Federal regulations that define Occupant Classification (Refer to “Occupant Classification System” in this section). 2 This vehicle may also be equipped with a driver inflatable knee blocker located on the instrument panel below the steering column. This vehicle may also be equipped with left and right window bags to protect the driver and passengers sitting next to a window.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years old and under should always ride buckled up in a rear seat. Infants in rear facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag. An airbag deployment can cause severe injury or death to infants in that position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during front airbag deployment could cause serious injury. Airbags need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Interconnecting Wiring • Knee Impact Bolster • Driver Inflatable Knee Blocker • Front Passenger Seat Occupant Classification System (OCS) 49 severity, the front control module determines the proper rate of inflation. The front airbag inflators are designed to provide different rates of airbag inflation. • The ORC may modify the rate of inflation based on the occupant size provided by the Occupant Classification Module.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Also, the ORC turns on the AIRBAG warning light and PAD indicator light in the center of the instrument panel for 6 to 8 seconds for a self-check when the ignition is first turned on. After the self-check, the AIRBAG warning light will turn off. The PAD indicator light will function normally (Refer to “Passenger Airbag Disable (PAD) Indicator Light” in this section).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the airbags inflate to their full size. The airbags fully inflate in about 50–70 milliseconds. This is about half of the time it takes to blink your eyes. The airbags then quickly deflate while helping to restrain the driver and front passenger. The driver’s and passenger’s front airbag gas is vented through the airbag material towards the instrument panel. In this way the airbags do not interfere with your control of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Knee Impact Bolsters help protect the knees, and position everyone for the best interaction with the front airbag. • If your vehicle contains a Passenger Airbag Disable indicator light, it will be equipped with the Occupant Classification System (OCS). The OCS system will classify an occupant into a size category based on sensor readings from within the seat cushion. Occupants should try to remain in a normally seated position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC will not allow front airbag deployment in the event of a collision for occupants classified into the empty or child size categories. The PAD indicator light will illuminate indicating that the Passenger Airbag is OFF when the OCS has determined that the occupant size category is a child. Also, when the seat is empty or an object that weighs less than a predetermined threshold is placed on the seat, the light will remain OFF.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For almost all sizes of properly seated adults, the airbag will be enabled in the event of a collision. For small teenagers and some small adults, depending on size, the airbag may or may not be enabled in the event of a collision. Both drivers and passengers should always use the PAD indicator light as an indication if the front passenger is properly positioned or not.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Belt Tension Sensor (BTS) is located at the outboard passenger lap belt anchor. The BTS generates a signal based on outboard lap belt tension. This signal is sent to the OCM to ensure that the resultant bladder pressure increase due to applied lap belt tension does not cause a small occupant to be classified as a larger occupant. • The Bladder Assembly is located beneath the seat cushion foam. The pressure sensor sends a signal to the OCM.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not use prior or future model year seat covers not designated for the specific model being repaired. Always use the correct seat cover specified for the vehicle. • Do not replace the seat cover with an aftermarket seat cover. • Do not add a secondary seat cover other than those approved by DaimlerChrysler/Mopar.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause • it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or frame.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The light remains on or flickers after the 6 to 8 second interval. • The light flickers or comes on and remains on while driving. Child Restraint Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The lower anchor bars of the LATCH System are located where the seat back meets the seat cushion. Tether Strap Mounting Latch Anchorages The tether anchors are located on the rear surface of the seat. Child restraint systems designed to be compatible with the vehicles LATCH System are now available. LATCH child restraints make installation into the vehicle simple and convenient.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 When using the LATCH System, always follow the child restraint manufactures installation instructions. NOTE: If your child restraint seat is not LATCH compatible, install the restraint using the vehicle seat belts. Tether Anchors There are tether strap anchorages behind all second row seating positions and if equipped the driver’s side third row seating position. The tether anchors are located in the rear surface of the seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the tether anchorage is used in the third row seating position, the strap should be positioned straight over the top of the seatback. Third Row Tether Strap Routing Infants and Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to ensure you have the right seat for your child.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 9 kg (20 lbs). ⬙Convertible⬙ child seats can be used either rearward-facing or forward-facing in the vehicle. Convertible child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children who weigh more than 9 kg (20 lbs) but are less than one year old.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward facing child restraint should only be used in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Buckle the child into the seat according to the child restraint manufacturer’s directions. • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Don’t leave it loose in the vehicle. In a sudden stop or collision, it could strike the occupants or seatbacks and cause serious personal injury.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE have tether straps, and you are urged to take advantage of all of the available attachments provided with your child restraint in any vehicle. Not all child restraint systems will be installed as we have described here. Again, carefully follow the instructions that come with the child restraint system. WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS WARNING! Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below. Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light The light should come on and remain on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the LED is not lit during starting, have it checked. If the light stays on or comes on while driving, have the system checked by an authorized dealer. Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 ▫ Heated Remote Control Mirrors . . . . . . . . . . . .78 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .75 ▫ Illuminated Vanity Mirrors . . . . . . . . . . . . . . . .78 ▫ Automatic Dimming Mirror — If Equipped . . . .76 䡵 Hands–Free Communication (UConnect™) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 ▫ Third Row Seating — If Equipped . . . . . . . . . 113 ▫ 10–Way Driver’s Power Seat — If Equipped . . 102 ▫ Load Floor — If Equipped . . . . . . . . . . . . . . . 114 ▫ 8–Way Driver’s Power Seat — If Equipped . . . 103 ▫ Plastic Grocery Bag Retainer . . . . . . . . . . . . . 115 ▫ 4–Way Passenger’s Power Seat . . . . . . . . . . . . 103 䡵 Driver Memory System — If Equipped . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . 124 䡵 Traction Control Switch — If Equipped . . . . . . . 130 ▫ Headlight Time Delay . . . . . . . . . . . . . . . . . . 124 䡵 Rear Park Assist System — If Equipped . . . . . . . 131 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . 124 䡵 Adjustable Pedals — If Equipped . . . . . . . . . . . 133 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Garage Door Opener — If Equipped . . . . . . . . . 138 ▫ Electrical Outlet Use With Engine Off . . . . . . . 150 ▫ Programming Homelink . . . . . . . . . . . . . . . . 139 䡵 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 ▫ Canadian Programming/Gate Programming . . 143 ▫ Front Seat Cupholders . . . . . . . . . . . . . . . . . . 150 ▫ Using Homelink . . . . . . . . . . . . . . . . . . . . . . 144 ▫ Second Row Seat Cupholders . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical adjustment of the mirror. Adjusting Rear View Mirror 75 Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped If the switch is in the “Auto” position the mirror will automatically adjust for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the mirror will illuminate to indicate when this feature is on. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror. Outside Mirror — Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the portion of the mirror closest to the vehicle. This type of mirror will give a much wider view to the rear, and especially of the lane next to your vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Remote-Control Mirrors Use the mirror select switch, located on the driver’s door trim panel above the power window switches, to adjust the view obtained in the outside mirrors. Press the rocker switch to the L or R for Left or Right mirror selection. Use the center off position to guard against accidentally moving a mirror position. Select a mirror and press one of the four arrows for the direction you want the mirror to move.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Sun Visor Extension The sun visors may be pulled out to provide extended coverage of the side glass. For UConnect Customer Support call 1-877-855-8400 or visit the UConnect website (www.chrysler.com/ uconnect). HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone* using simple voice commands (e.g.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE linked to system. Only one linked (or paired) cellular phone can be used with the system at a time. The system is available in English, Spanish, or French languages (as equipped). The rearview mirror contains the microphone for the system and the control buttons that will enable you to access the system. The diagram below shows the mirror with the appropriate buttons. Individual button behavior is discussed in the ⬙Operation⬙ section.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ system is fully integrated with the vehicle’s audio system. The volume of the UConnect™ system can either be adjusted from the radio volume control knob, or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the UConnect™ system such as ⬙CELL⬙ or caller ID on certain radios.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Help Command If you need assistance at any prompt or if you want to know what your options are at any prompt, say ⬙Help⬙ following the voice on beep. The UConnect™ system will play all the options at any prompt if you ask for help. To activate the UConnect™ system from idle, simply press the ’Phone’ button and follow audible prompts for directions. All UConnect™ system sessions begin with a press of the ’Phone’ button on the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will be asked to say a four-digit pin number which you will later need to enter into your cellular. You can enter any four-digit pin number. You will not need to remember this pin number after the initial pairing process. • The UConnect™ system will then prompt you to begin the cellular phone pairing process on your cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For example, you can say ⬙234-567-8901.⬙ The phone number that you enter must be of valid length and combination. The UConnect™ limits the user from dialing invalid combination of numbers. For example, 234-567-890 is nine digits long, which is not a valid phone number - the closest valid phone number has ten digits. • After the ⬙Ready⬙ prompt and the following beep, say the name of the person you want to call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, say the name of the new entry. Use of long names helps the voice recognition and is recommended. For example, say ⬙Robert Smith⬙ or ⬙Robert⬙ instead of ⬙Bob.⬙ • When prompted, enter the number designation (e.g.: ⬙Home,⬙ ⬙Work,⬙ ⬙Mobile,⬙ or ⬙Pager⬙). This will allow you to store multiple numbers for each phonebook entry, if desired. • When prompted, recite the phone number for the phonebook entry that you are adding.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ⬙Phonebook Edit⬙ can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mobile and a home number, but you can add John Doe’s work number later using the ⬙Phonebook Edit⬙ feature. • After you enter the name, the UConnect™ system will ask you which designation you wish to delete: home, work, mobile or pager. Say the designation you wish to delete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook List Names.⬙ • The UConnect™ system will play the names of all the phonebook entries. • To call one of the names in the list, press the ⬙Voice Recognition’ button during the playing of the desired name and say ⬙Call⬙. NOTE: the user can also exercise ⬙Edit⬙ or ⬙Delete⬙ operations at this point.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cell phone. Press the ’Phone’ button to place the current call on hold and answer the incoming call. NOTE: The UConnect™ system compatible phones in market today do not support rejecting an incoming call when another call is in progress.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 Conference Call When two calls are in progress (one active and one on hold), press and hold the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call. Redial Three-Way Calling To initiate three-way calling, press the ’Voice Recognition’ button while a call is in progress and make a second phone call as described in section ⬙Making a Second Call while Current Call in Progress.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After ignition key is switched off, a call can continue on the UConnect™ system either until the call ends or until the vehicle battery condition dictates cessation of the call on the UConnect™ system and transfer of the call to the mobile phone. • After ignition key is switched to off, a call can continue on the UConnect™ system for certain duration, after which the call is automatically transferred from the UConnect™ system to the mobile phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the phone is not reachable and the UConnect™ system is operational, you may reach the emergency number as follows: • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Emergency⬙ and the UConnect™ system will instruct the paired cellular phone to call the emergency number. This feature is only supported in the USA.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Working with Automated Systems This method is designed to be used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated telephony system. You can use your UConnect™ system to access a voicemail system or an automated service, such as, paging service or automated customer service.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Confirmations.⬙ The UConnect™ system will play the current confirmation prompt status and you will be given the choice to change it. Phone and Network Status Indicators The UConnect™ system will provide notification to inform you if your cellular phone is in roaming status, has low signal strength, or has a low battery when you are trying to place a phone call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say ⬙Mute-off.⬙ Information Service When using AT&T Wireless Service, dialing to phone number ⬙#121,⬙ you can access voice activated automated system to receive news, weather, stocks, traffic, etc. related information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnect™ system will play the phone names of all paired cellular phones in order from the highest to the lowest priority. Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system. The phone must have been previously paired to the UConnect™ system that you want to use it with. • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Select Phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Things You Should Know About Your UConnect™ System • low road noise, Voice Recognition (VR) • fully closed windows, • Always wait for the beep before speaking. • Speak normally, without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you. • Make sure that no one other than you is speaking during a voice recognition period.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • It is not recommended to store similar sounding names in the UConnect™ phonebook. • UConnect™ phonebook name tag recognition rate is optimized for the person who stored the name in the phonebook. • You can say ⬙O⬙ (letter ⬙O⬙) for ⬙0⬙ (zero). ⬙800⬙ must be spoken ⬙eight-zero-zero.⬙ • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Bluetooth Communication Link Cellular phones have been found to occasionally loose connection to the UConnect™ system. When this happens, the connection can generally be re-established by switching the phone off/on. Your cell phone is recommended to remain in Bluetooth ⬙on⬙ mode. Reset In rare instances, it may be necessary to reset the UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS 10–Way Driver’s Power Seat — If Equipped The driver’s power seat switches are located on the driver’s front door trim panel. The bottom switch controls up/down, forward/rearward, and tilt adjustment. The top switch controls the seatback recline adjustment and the middle switch controls the lumbar adjustment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjust the seat only while the vehicle is parked. Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. 8–Way Driver’s Power Seat — If Equipped The driver’s power seat switches are located on the driver’s front door trim panel. The bottom switch controls up/down, forward/rearward, and tilt adjustment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the head restraint so that the upper edge is as high as practical. To raise the head restraint, pull up on the head restraint. To lower the head restraint, depress the release tab located at the base of the head restraint and push down on the head restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped This feature heats the driver, front passenger and second row seats. The controls for the front heated seats are located on the door trim panel next to the power seat switches. Front Heated Seat Switch 105 Press the switch once to select a heat setting (high or low) and press the switch a second time in the same direction to turn the heated seat off. The indicator light will show when LOW or HIGH heat is ON.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The controls for the second row heated seats are located on the center console between the seats. Press the switch once to select a heat setting (high or low) and press the switch a second time in the same direction to turn the heated seat off. The indicator light will show when LOW or HIGH heat is ON.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 Second Row Manual Seat Recliner — If Equipped The recliner mechanism control is on the outboard side of the seat. To recline, lean forward slightly, lift the lever, then push back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position. Using body pressure, lean forward and rearward on the seat to be sure the seatback has latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or fatally injured. Use the recliner only when the vehicle is parked. Second Row Manual Seat Adjuster — If Equipped The adjusting bar is located under the front of the seat. Pull the bar up and move the seat to the desired position. Release the bar to lock the seat into position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 WARNING! Adjust the seat only while the vehicle is parked. Adjusting a seat while the vehicle is moving is dangerous. The seat belt might not be properly adjusted and you could be injured. 3 Second Row Bench Seating — If Equipped The second row seats may be used with either or both seatbacks folded forward for additional storage space. To fold the seat, remove any objects from in front of or on the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Be sure there is nothing in front of the second row seat cushion before folding it down. Damage to the seat may occur. 4. Pull up on the seatback release lever located on the outboard side of the seat labeled “1” and fold the seatback down. Second Row Fold & Tumble Seats — If Equipped The second row seats can be folded and tumbled forward for easy access to the third seat or rear cargo area. To fold and tumble the seat, follow these steps: 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Pull up on the release handle labeled “2” and lift firmly to tumble the seat fully forward. If the seat contacts the rear of the front seat, move the front seat forward. 111 To relatch the seat, tilt the seat rearward and push down firmly to engage the rear attachments. Then lift the seatback release lever labeled “1” and pull the seatback up to return it to its full upright position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To fold and tumble the seat forward, follow these steps: 1. Pull up on the seatback release handle “1” located on the back of the seat to fold the seatback down. Release Strap 2 Location Release Handle 1 Location 2. Pull the release strap “2” located at the bottom of the seat to lift and tumble the seat forward. To relatch the seat, tilt the seat rearward and push down firmly to engage the rear attachments.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Third Row Seating — If Equipped The third row seats may be used with either or both seatbacks folded forward for additional storage space. To fold the seat, remove any objects from in front of or on the seat. Then pull handle located on the seatback and push it forward. 113 WARNING! Do not sit in the 3rd row seat with the second row seatbacks folded or with the second row seats folded and tumbled.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Not all head restraints in this vehicle are the same. • • • • Head restraints from one seating position should not be removed and installed in any other seating position. In a collision, serious injury or death may result if the proper head restraint is not installed on each seat. The cargo area in the rear of the vehicle should not be used as a play area by children. They could be seriously injured in a collision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Plastic Grocery Bag Retainer Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all front seats. The floor supports the partial weight of the bagged goods. 3 Load Floor Panel NOTE: Be sure to reattach the strap to secure the load floor panel when not in use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER MEMORY SYSTEM — IF EQUIPPED If your vehicle is equipped with memory systems, your remote keyless entry transmitter or memory seat buttons on the driver’s door panel can be used to recall the driver’s seat, outside mirrors, adjustable pedals (if equipped) and radio station presets to saved positions. The memory seat buttons located on the driver’s door will always recall stored settings.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your vehicle has been delivered with two remote keyless entry transmitters. One or both transmitters can be linked to either memory position. Up to eight remote keyless entry transmitters can be used with your vehicle. The memory seat system can also accommodate up to eight transmitters linked to either of the two stored seat positions or any combination of the two positions. To Program Memory Seat Buttons & RKE Transmitters, Follow These Steps: 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Repeat the above steps for the second position using the other driver’s door numbered button and Remote Keyless Entry Transmitter. Each time the SET (S) button and a numbered button are pressed, you erase the old memory and store a new one. To Disable A Transmitter Link, Follow These Steps: 1. Select “Remote Linked To Memory” from the Electronic Vehicle Information Center, Customer Programmable features. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. 119 Next, push to the left the safety catch located under the front edge of the hood, near the center. 3 Hood Safety Catch Hood Release Lever Use the hood prop rod to secure the hood in the open position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 15 cm (6 inches) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. You could have a collision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 NOTE: The lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. Interior Lights The interior lights come on when a door is opened. The interior lights will automatically turn off in about 15 minutes if a door is left open or the dimmer control is left in the Dome light position. Turn the ignition switch ON to restore the interior light operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multi-Function Lever The Multi-Function Lever controls the operation of the headlights, parking lights, turn signals, headlight beam selection, instrument panel light dimming, interior lights, the passing lights, and fog lights. The lever is located on the left side of the steering column. Headlights, Parking Lights, Instrument Panel Lights Turn the end of the Multi-Function Lever to the first detent for parking light and instrument panel light operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Dome Light Position Rotate the dimmer control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position. Parade Mode (Daytime Brightness Feature) Rotate the dimmer control upward to the first detent. This feature brightens the odometer and radio display when the parking lights or headlights are on during daylight conditions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The engine must be running before the headlights will come ON in the Automatic mode. Daytime Running Lights (Canada Only) The high beam headlights will come on as Daytime Running Lights whenever the ignition switch is on, the headlights are off, and the parking brake is off. The headlight switch must be used for normal night time driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The fog lights will only operate with the headlights on low beam. Selecting high beam headlights will turn off the fog lights. Turn Signals Move the Multi-Function Lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down without moving beyond the detent.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch on the control lever. The lever is located on the right side of the steering column. Rotate the end of the control lever to select the desired wiper speed. Windshield Washers To use the front washer, pull the lever toward you and hold while spray is desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Windshield Wiper Operation Rotate the end of the lever to the second detent for Low speed wiper operation, or to the third detent for High speed operation Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. Rotate the end of the lever to the first detent position, then turn the end of the lever to select the desired delay interval.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rotating the center of the switch up to the DEL (Delay) position or the ON position will activate the rear wiper. Push the lever forward to initiate the rear wash function in any of the three positions. The washer pump will continue to operate as long as the lever is pressed. Upon release, the rear wiper will cycle two times before returning to the set position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, pull the lever, located behind the turn signal control, toward you and move the steering wheel up or down, as desired. Release the lever to lock the steering wheel firmly in place. Tilt Steering Column Control 129 WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TRACTION CONTROL SWITCH — IF EQUIPPED The traction control Indicator, located in the instrument cluster, will light up when the Traction Control is in use. To turn the system OFF, press the Traction Control switch located on center console next to the ash tray, until the traction control Indicator in the instrument cluster lights up.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 • The Traction Control system will make buzzing or clicking sounds when in operation. REAR PARK ASSIST SYSTEM — IF EQUIPPED This system is used to help drivers determine if an obstacle is in the way of the vehicle while it is backing up in addition to the use of inside rearview and outside mirrors. When the driver selects Reverse the system scans for objects behind the vehicle using four sensors located in the rear bumper.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Drivers must be careful when backing up even when using the Rear Park Assist System. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, other vehicles, obstructions, and blind spots before backing up. Failure to do so can result in serious personal injury or death. The display contains two sets of yellow and red LEDs that the driver can see in the rear view mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward or away from the driver to provide improved position with the steering wheel. The adjustable pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. The switch is located on the drivers door trim panel next to the power seat switches.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The pedals can be adjusted while driving. CAUTION! • The pedals cannot be adjusted when the vehicle is in R (Reverse) or when the Speed Control is ON. A message will be displayed in the Electronic Vehicle Information Center (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjustable Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse”).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidently set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you aren’t using it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate: A soft tap on the brake pedal, pushing the “CANCEL” button or normal braking while slowing the vehicle will deactivate the speed control without erasing the memory. Pushing the “ON/OFF” button to the OFF position or turning off the ignition erases the speed memory. To Resume Speed: To resume a previously set speed, push and release the “ACCEL/RESUME” button. Resume can be used at any speed above 25 mph (40 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Four speed automatic transmissions will experience a downshift to 3rd gear while climbing uphill or descending downhill. This downshift to 3rd gear is necessary to maintain vehicle set speed. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy/Reading Lights At the forward end of the console are two courtesy/ reading lights. Press the lens to turn these lights on. Press a second time to turn the lights off. The lights also turn on when a front door, a rear door or the liftgate is opened. The lights will also turn on when the unlock button on the remote keyless entry transmitter is pressed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features it could cause injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Press and hold the two outer HomeLink buttons, and release only when the indicator light begins to flash or the EVIC display shows “Channels Cleared” (after 20 seconds). Do not hold the buttons for longer than 30 seconds and do not repeat step one to program a second and/or third hand-held transmitter to the remaining two HomeLink buttons.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause serious injury or death. WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If the EVIC display shows “Did Not Train” repeat steps 2–4. 5. Press and hold the just trained HomeLink button and observe the indicator light or the EVIC display. If the indicator light stays on constantly, programming is complete and your device should activate when the HomeLink button is pressed and released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 8. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink button. Repeat the ⴖpress/hold/releaseⴖ sequence a second time, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink should now activate your rolling code equipped device.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties or questions, contact HomeLink at: www.homelink.com or 1-800-3553515.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Security If you sell your vehicle, be sure to erase the frequencies by following the “Erasing HomeLink Buttons” instructions in this section. POWER SUNROOF — IF EQUIPPED The power sunroof buttons are located between the sun visors on the overhead console. This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 3 • This device may not cause harmful interference.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press and hold the “OPEN” button rearward to fully open the sunroof. The sunroof can be stopped at any position between closed and full open. Momentarily pressing the “OPEN” button rearward will activate the Express Open Feature, causing the sunroof to open automatically. Press and hold the “VENT” button to open the vent. The sunroof can be stopped at any position between closed and full vent.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To close the sunroof, press and hold the “CLOSE” button forward. Again, any release of the button will stop the movement and the sunroof will remain in a partial open condition until the button is pushed forward again. The sunshade can be opened manually. It will also open as the sunroof opens. The sunshade cannot be closed if the sunroof is open. 147 WARNING! • Never leave children in a vehicle, with the keys in the ignition switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 The outlets include tethered caps labeled with a key or battery symbol indicating the power source. The passenger side instrument panel and center console outlets are powered directly from the battery, items plugged into these outlets may discharge the battery and/or prevent engine starting. The passenger side and center console outlets are protected by an automatic reset circuit breaker.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from • • • the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. Accessories that draw higher power (i.e. coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second Row Seat Cupholders On vehicles equipped with five passenger seating the second row seat cupholders are located in middle of the seatback armrest. Pull down on the armrest to access the cupholders. Push the armrest up when the cupholders are no longer needed. 151 On vehicles equipped with six passenger seating the second row seat cupholders are located in the forward edge of the center console located between the second row seats.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Cargo Storage Bin — If Equipped The storage bin is located in the floor of the rear cargo area. To open lift up on the handle. Retractable Cargo Area Cover — If Equipped To cover the cargo area: 1. Fold down the third row seatbacks. 2. Unfold the cargo cover extensions and lock into place. 3. Insert the pins on the ends of the cover into the slots located on the trim panel behind the second row seatbacks. 4. Grasp the center portion of the cover flap.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 WARNING! 3. Insert the pins on the ends of the cover into the slots located on the trim panel behind the third row seatbacks. In an accident a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do not store in the vehicle. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or collision a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. • The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. 155 Distribute cargo weight evenly on the roof rack crossbars. The roof rack does not increase the total load carrying capacity of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: To reduce the amount of wind noise when the cross bars are not in use, move both cross bars next to each other towards the rear of the vehicle in the rear most position. The tie down holes on the cross bar ends should always be used to tie down the load. Check the straps frequently to be sure that the load remains securely attached.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack. LOAD LEVELING SYSTEM The automatic load leveling system will provide a level riding vehicle under most passenger and cargo loading conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instruments And Controls . . . . . . . . . . . . . . . . . 162 䡵 Setting The Analog Clock . . . . . . . . . . . . . . . . . 182 䡵 Base Instrument Cluster . . . . . . . . . . . . . . . . . . 163 䡵 Electronic Digital Clock . . . . . . . . . . . . . . . . . . 183 䡵 Premium Instrument Cluster . . . . . . . . . . . . . . . 164 ▫ Clock Setting Procedure . . . . . . . . . . . . . . . . . 183 䡵 Instrument Cluster Descriptions . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operation Instructions - (CD Mode For MP3 Audio Play) . . . . . . . . . . . . . . . . . . . . . 192 䡵 Sales Code RBP—AM & FM Stereo Radio With Cassette Tape Player, CD Player, And Optional CD/DVD Changer Controls . . . . . . . . . . . . . . . 193 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . . 194 ▫ Tape Player Operation . . . . . . . . . . . . . . . . . . 198 ▫ CD Player Operation . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Using The PTY (Program Type) Button (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . . 216 ▫ PTY Button ⬙Scan⬙ . . . . . . . . . . . . . . . . . . . . . 217 ▫ PTY Button ⬙Seek⬙ . . . . . . . . . . . . . . . . . . . . . 217 ▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . . 217 ▫ Reception Quality . . . . . . . . . . . . . . . . . . . . . 217 䡵 Remote Sound System Controls . . . . . . . . . . . . . 218 ▫ Radio Operation . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENTS AND CONTROLS
UNDERSTANDING YOUR INSTRUMENT PANEL 163 BASE INSTRUMENT CLUSTER 4
UNDERSTANDING YOUR INSTRUMENT PANEL PREMIUM INSTRUMENT CLUSTER
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Voltage Light This light monitors the electrical system voltage. The light should turn on momentarily as the engine is started. If the light stays on or turns on while driving, it indicates a problem with the charging system. Immediate service should be obtained. 2. Temperature Gauge The temperature gauge shows engine coolant temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. 3. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position.
UNDERSTANDING YOUR INSTRUMENT PANEL If the ABS light remains on or turns on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes.
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! The light also will turn on when the parking brake is applied with the ignition switch in the ON position. Driving a vehicle with the brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application.
UNDERSTANDING YOUR INSTRUMENT PANEL • The system has been deactivated to prevent damage to the brake system due to overheated brake temperatures. NOTE: Extended heavy use of Traction Control may cause the system to deactivate and turn on the Traction Control Light. This is to prevent overheating of the brake system and is a normal condition. The system will remain disabled for about 4 minutes until the brakes have cooled. The system will automatically reactivate and turn off the Traction Control Light. 9.
UNDERSTANDING YOUR INSTRUMENT PANEL replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined. 14. Cruise Indicator This display indicator shows that the Speed Control System is ON. The two trip odometers show individual trip mileage. To switch from odometer to trip odometers, press and release the Trip Odometer button.
UNDERSTANDING YOUR INSTRUMENT PANEL The Malfunction Indicator Light flashes to alert you to serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced as soon as possible if this occurs. 16. High Beam Light This light shows that the headlights are on high beam. Pull the Multi-Function lever towards the steering wheel to switch the headlights from high or low beam. 17.
UNDERSTANDING YOUR INSTRUMENT PANEL 21. Tire Pressure Monitor Warning Light — If Equipped This light will turn on when there is a Low tire pressure condition. The light will remain on until the tire pressure is properly set. The light will also flash if a problem exist with any tire sensor. The light will flash for approximately three seconds every 10 minutes or until the problem with the sensor is corrected. This light will turn on momentarily as a bulb check when the engine is started.
UNDERSTANDING YOUR INSTRUMENT PANEL 22. Airbag Light This light turns on and remains on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the light is not on during starting, stays on, or turns on while driving, have the system inspected by an authorized dealer as soon as possible. 23. Electronic Vehicle Information Center Display — If Equipped When the appropriate conditions exist, this display shows the Electronic Vehicle Information Center (EVIC) messages. 24.
UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED The Electronic Vehicle Information Center (EVIC) consists of the following: • Vehicle information warning message displays • Tire Pressure Monitor System — If Equipped • Customer programmable features • Compass display • Mini-Trip functions Pressing the MENU button will change the displayed programming features. Pressing the STEP button will display the available choices.
UNDERSTANDING YOUR INSTRUMENT PANEL • SET INHIBITED DUE TO MOTION (with a single chime) • FOB LINKED (with a single chime) • FOB UNLINKED (with a single chime) • PARK BRAKE ENGAGED (with a single chime) • LOW BRAKE FLUID (with a single chime) • LOW FUEL (with a single chime) • MENU IN PARK ONLY • LIST # ALERT MESSAGES • UNLOCK TO OPEN LIFTGATE (with a single chime) • PUT IN PARK FOR LIFTGATE (with a single chime) • TOO COLD FOR PWR LIFTGATE (with a single chime) • TOO HOT FOR PWR LIFTGATE (with a single ch
UNDERSTANDING YOUR INSTRUMENT PANEL • CHANNEL 1, 2, OR 3 TRAINING (with a single chime) • TCS ACTIVE (Traction Control System, with a graphic) • CHANNEL 1, 2, OR 3 TRAINED (with a single chime) • SERVICE TCS SYSTEM (Traction Control System, with a graphic and single chime) • CLEARING CHANNELS • CHANNELS CLEARED • CHANNELS DEFAULTED • DID NOT TRAIN • 1,2,3 OR 4 TIRE(S) LOW PRESSURE (Refer to “Starting And Operating, Tire Section”) • 1,2,3 OR 4 TIRE(S) HIGH PRESSURE (Refer to “Starting And Operating
UNDERSTANDING YOUR INSTRUMENT PANEL Park Assist System? ON/OFF When this feature is selected the system scans for objects behind the vehicle using four sensors located in the rear bumper. Objects can be detected from up to 71 inches (180 cm). Pressing the “STEP” button while in this display will disable/enable the Rear Park Assist System.
UNDERSTANDING YOUR INSTRUMENT PANEL keyless entry unlock button. Pressing the STEP button when in this display will select DRIVER’S DOOR 1ST or ALL DOORS. Remote Linked To Memory? (Available with Memory Seat Only) When this feature is selected the memory seat, mirror, and radio settings will return to the memory set position when the remote keyless entry “Unlock” button is pressed.
UNDERSTANDING YOUR INSTRUMENT PANEL turn off when the wipers are turned off if they were turned on in this way. Pressing the STEP button when in this display will select “Yes” or “No.” NOTE: Turning the headlights on during the daytime causes the instrument panel lights to dim. To increase the brightness, refer to “Lights” in this section.
UNDERSTANDING YOUR INSTRUMENT PANEL driver can more easily exit the vehicle. The seat will return to the memorized seat location (if REMOTE LINK TO MEMORY is set to YES) when the remote keyless entry transmitter is used to unlock the door. Pressing the STEP button when in this display will select “Yes” or “No.” Compass Display — If Equipped This display provides one of eight compass readings to indicate the direction the vehicle is facing.
UNDERSTANDING YOUR INSTRUMENT PANEL 181 Compass Variance Compass Variance is the difference between magnetic North and Geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set. NOTE: Magnetic materials should be kept away from the overhead console.
UNDERSTANDING YOUR INSTRUMENT PANEL To set the variance: Turn the ignition switch ON and set the display to Compass. Press the RESET button for approximately 5 seconds but no more than 10 seconds. The “COMPASS VARIANCE” message and the last variance zone number will be displayed. Press the STEP button to select the proper variance zone as shown in the map. Press the RESET button to set the new variance zone and resume normal operation.
UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the ON or ACC position and the time button is pressed. SALES CODE RAH—AM & FM STEREO RADIO WITH CD PLAYER AND CD/DVD CHANGER CONTROLS When the ignition switch is in the OFF position, or when the radio frequency is being displayed, time keeping is accurately maintained.
UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. PTY (Program Type) Pressing the INFO button once while in FM mode will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out, the PTY icon will turn off.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Radio Display Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports Talk Talk Top 40 Top 40 Weather Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM and Satellite (if equipped) modes.
UNDERSTANDING YOUR INSTRUMENT PANEL Tuning Press the TUNE control up or down to increase or decrease the frequency. If you press and hold the button, the radio will continue to tune until you release the button. The frequency will be displayed and continuously updated while the button is pressed. Balance The Balance control adjusts the left-to-right speaker balance. Press the AUDIO button, select BALANCE, then press SEEK + or SEEK ⫺ to adjust the balance.
UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into memory. You can recall the stations stored in SET 2 memory by pressing the pushbutton twice.
UNDERSTANDING YOUR INSTRUMENT PANEL Inserting The Compact Disc CAUTION! This CD player will accept only 4–3/4 inch (12cm) discs only. The use of other sized discs may damage the CD player mechanism. You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day. If you insert a disc with the ignition OFF, the display will show the time of day for about 5 seconds, then go out.
UNDERSTANDING YOUR INSTRUMENT PANEL RND — Random Play Press the RND button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track. Press TUNE FF to fast forward through the tracks. Press the FF button a second time to stop the fast forward feature.
UNDERSTANDING YOUR INSTRUMENT PANEL When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file normally. UDF and Apple HFS formats are not supported. The radio uses the following limits for file systems: • Maximum number of directory levels: 15 • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙.
UNDERSTANDING YOUR INSTRUMENT PANEL MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 Sampling Frequency (kHz) 48, 44.1, 32 24, 22.05, 16 Bit rate (kbps) 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 ID3 Tag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported.
UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (CD Mode For MP3 Audio Play) SEEK Button (CD Mode For MP3 Play) Pressing the SEEK + button plays the next MP3 File. Pressing the SEEK ⫺ button plays the beginning of the MP3 file. Pressing the button within the first ten seconds plays the previous file. INFO Button (CD Mode For MP3 Play) Press and INFO button while playing MP3 disc.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. 193 SALES CODE RBP—AM & FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER, AND OPTIONAL CD/DVD CHANGER CONTROLS Operating Instructions - Video Entertainment System (VES威) (If Equipped) Refer to 6 Disc CD/DVD Changer (RDV) section of the Owner’s Manual.
UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control to the right to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. PTY (Program Type) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather Radio Display Rock Soft Soft Rck Soft R&B Sports Talk Top 40 Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM and Satellite (if equipped) modes.
UNDERSTANDING YOUR INSTRUMENT PANEL Scan Press and release the SCAN button to search for the next station in either the AM or FM mode. The radio will pause for 5 seconds at each listenable station before continuing to the next. To stop the search, press the SCAN button a second time. Tune Press the TUNE control up or down to increase or decrease the frequency. If you press and hold the button, the radio will continue to tune until you release the button.
UNDERSTANDING YOUR INSTRUMENT PANEL SET 1 will now show in the display window. Select the “1–5” button you wish to lock onto this station and press and release that button. If a button is not selected within 5 seconds after pressing the SET button, the station will continue to play but will not be locked into push-button memory. You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window.
UNDERSTANDING YOUR INSTRUMENT PANEL Tape Player Operation Insert the cassette with the exposed tape side toward the right and the mechanical action of the player will gently pull the cassette into the play position. Seek Press the SEEK button up for the next selection on the tape and down to return to the beginning of the current selection. NOTE: When subjected to extremely cold temperatures, the tape mechanism may require a few minutes to warm up for proper operation.
UNDERSTANDING YOUR INSTRUMENT PANEL Rewind — RW Press the RW button down momentarily to reverse the tape direction. The tape will rewind until the button is pressed again or until the beginning of the tape is reached. At the beginning of the tape, the tape will play in the opposite direction. EJT Tape Press the EJT TAPE button and the cassette will disengage and eject from the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. Inserting The Compact Disc You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio off, the display will show CD and the time of day will be displayed. If the power is on, the unit will switch from radio to CD mode and begin to play when you insert the disc.
UNDERSTANDING YOUR INSTRUMENT PANEL FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW (Reverse) button works in a similar manner. Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace.
UNDERSTANDING YOUR INSTRUMENT PANEL Disc Up/Program Button 1 Press the DISC (button 1) button to play the next available disc. Disc Down/Program Button 5 Press the DISC (button 5) button to play the previous disc. Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play. This feature plays the selections on the currently playing compact disc in random order to provide an interesting change of pace.
UNDERSTANDING YOUR INSTRUMENT PANEL 203 6 DISC CD/DVD CHANGER (RDV) — IF EQUIPPED The Rear Seat Audio/Video System allows passengers to listen to a CD or DVD from the 6 disc CD/DVD changer through wireless headphones, while the front seat passengers listen to either AM/FM, Cassette or CDs from the radio speakers. A remote control is provided for functions such as changing tracks or DVD functions, as well as selecting discs loaded in the 6 disc CD/DVD changer while listening to the Rear Audio/Video System.
UNDERSTANDING YOUR INSTRUMENT PANEL To insert disc(s) into the changer, follow the instructions shown: 1. On vehicles equipped with the premium version, select and press any numbered button without an illuminated light above it. 2. Gently insert the disc with the label facing up while the light below the loading slot is illuminated. On vehicles equipped with the premium version the light above the chosen button will also be flashing, indicating which numbered position the disc will be loaded into.
UNDERSTANDING YOUR INSTRUMENT PANEL • If you insert a disc with the ignition ON and the radio OFF, the DVD will automatically be pulled into the DVD changer and the display will show the time of day. • It is recommended to label home made burned discs with a permanent marker instead of adhesive labels. These types of labels may become loose and cause the disc to be stuck in the DVD player. This may cause permanent damage to the DVD mechanism.
UNDERSTANDING YOUR INSTRUMENT PANEL Remote Control Remote Control Buttons 1. Headphone Transmitter 2. Menu Up/Next Track/Chapter 3. Menu Left/Fast Rewind 4. Return 5. Setup 6. Pause/Play 7. Mute 8. Display 9. Mode 10. Program Down - Previous Disc 11. Program Up - Next Disc 12. Slow 13. Stop 14. Menu 15. Menu Down/Previous Track/Chapter 16.
UNDERSTANDING YOUR INSTRUMENT PANEL Remote Control Buttons 17. Enter 18. Light Headphone Transmitter Button (1) After a disc is inserted into the DVD changer, both the headphone transmitter button (1) on the remote control and the power button on the headphones must be turned ON before sound can be heard from the headphones. On some radios the headphone symbol will flash for approximately 5 seconds in the radio display, indicating the headphones are in use.
UNDERSTANDING YOUR INSTRUMENT PANEL PAUSE/PLAY Button (6) This button only functions in DVD video mode. Press this button once to pause the video, press a second time to play the video. MUTE Button (7) No function. DISP Button (8) This button only functions in DVD video mode. When a DVD video is playing, press this button to display the play menu options. MODE Button (9) No Function PROG UP/DOWN Buttons (10, 11) PROG UP selects the next disc loaded in the changer.
UNDERSTANDING YOUR INSTRUMENT PANEL NEXT/PREV Buttons (2, 15) Press the up arrow or the NEXT button for the next chapter or track on the disc. Press the down arrow or PREV button to return to the beginning of the current chapter or track. Press the down arrow or PREV button twice within two seconds to return to the previous chapter or track. Each press of the NEXT/PREV button up or down will toggle through the chapters or tracks.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Video Screen Push up on the release button to lower the video screen. 2. Enter Button This button will enter the selection from the on-screen menu. 3. Brightness Button Changes the brightness of the screen picture. Lowering Video Screen 1. Screen Width Button Changes the width of the screen picture.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 Operating Instructions — Headphones 4 Video Screen Controls Headphone Controls 1. Power Button 2. Volume Control 3.
UNDERSTANDING YOUR INSTRUMENT PANEL Power Button Pressing the power button will turn the headphones ON/OFF. An indicator light will illuminate on the headphone earpiece to indicate the headphones are ON. NOTE: • The headphones will turn off automatically in approximately 3 minutes if they lose the signal form the system or when the radio or rear audio/video system is turned off. Volume Control Rotate the volume control to adjust the volume to the desired listening level.
UNDERSTANDING YOUR INSTRUMENT PANEL General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. If you do not hear sound coming from the headphones, check for the following conditions: 1. Rear Seat Audio/Video System and headphones are on.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: To operate a video game unit a DC to AC adapter may be required, plug the adapter into any power outlet. Follow the manufactures instructions for the correct colors when connecting the RCA cables. NOTE: MP3 player’s, video game systems, camcorders connected to the RCA jacks and CD’s or DVD’s inserted into the CD/DVD changer can be heard through the headphones.
UNDERSTANDING YOUR INSTRUMENT PANEL ESN/SID Access With RBB, RAH and RBK Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the Tape Eject or CD Eject (depending on the radio type) and Time buttons simultaneously for 3 seconds. The first four digits of the twelve-digit ESN/SID number will be displayed. Press the SEEK UP button to display the next four digits. Continue to press the SEEK UP button until all twelve ESN/SID digits have been displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL • The current channel number will then be displayed until an action occurs. A CD or tape may remain in the radio while in the Satellite radio mode. Selecting a Channel Press and release the SEEK or TUNE buttons to search for the next channel. Press the top of the button to search up and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released.
UNDERSTANDING YOUR INSTRUMENT PANEL PTY Button ⴖSCANⴖ When the desired program type is obtained, press the ⬙SCAN⬙ button within five seconds. The radio will play 7 seconds of the selected channel before moving to the next channel of the selected program type. Press the ⬙SCAN⬙ button a second time to stop the search. NOTE: Pressing the ⬙SEEK⬙ or ⬙SCAN⬙ button while performing a music type scan will change the channel by one and stop the search.
UNDERSTANDING YOUR INSTRUMENT PANEL • Placing objects over or too close to the antenna can cause signal blockage. The following describes the left hand rocker switch operation in each mode: REMOTE SOUND SYSTEM CONTROLS The remote sound system controls are located on the rear surface of the steering wheel at the 3 and 9 o’clock positions.
UNDERSTANDING YOUR INSTRUMENT PANEL The button in the center of the left hand switch has no function in this mode. CD Player Pressing the top of the switch once will go to the next track on the CD. Pressing the bottom of the switch once will go to the beginning of the current track or to the beginning of the previous track if it is within one second after the current track begins to play. If you press the switch up or down twice it plays the second track, three times, it will play the third, etc.
UNDERSTANDING YOUR INSTRUMENT PANEL Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal. AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 5. A loose tape should be corrected before use. To rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the required directions. CD/DVD DISC MAINTENANCE To keep the CD/DVD discs in good condition, take the following precautions: Maintain your cassette tape player. The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played.
UNDERSTANDING YOUR INSTRUMENT PANEL RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL To replace the navigation map DVD lift the storage bin cover and liner in the rear cargo area, press the eject button and the disc will eject. Gently insert the new disc into the DVD unit with the label facing up. The disc will automatically be pulled into the DVD unit. 223 Manual Air Conditioning and Heating System CLIMATE CONTROLS The Air Conditioning and Heating System is designed to make you comfortable in all types of weather.
UNDERSTANDING YOUR INSTRUMENT PANEL second time the indicator light turns off, the blower will turn off and the system will be positioned in the recirculation mode. Blower Control The Blower controls the amount of air delivered to the passenger compartment. There are four blower speeds.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 Panel Mode Mode Control The mode control allows you to choose from several patterns of air distribution. 4 NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are identified by the small dots.
UNDERSTANDING YOUR INSTRUMENT PANEL Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vane knob on the center outlets down, will close off the air flow from the center outlets. The thumbwheel next to the outboard outlets can be rotated to regulate or shut off the air flow from these outlets. Bi-Level Mode Bi-Level Outlets Air comes from both the instrument panel outlets, floor outlets and defrost.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 NOTE: In many temperature lever positions, the bilevel mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets. Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL Air comes from the floor, defrost and side window demist outlets. This mode works best in cold or snowy conditions. It allows you to stay comfortable while keeping the windshield clear. Defrost Mode Air comes from the windshield and side window demist outlets. Use this setting when necessary to defrost your windshield and side windows.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 Cool dehumidified air comes through the outlets selected by the Mode Control. To turn off the air conditioning, press the A/C button a second time. The indicator light will turn off. Economy Mode If economy mode is desired, press the A/C button to turn off the indicator light, and the A/C compressor. Move the temperature control lever to the desired temperature. NOTE: • The compressor will not engage until the engine has been running for a few seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL • In cold weather, use of the Recirculation mode may lead to excessive window fogging. The Recirculation mode is not allowed in the Mix and Defrost modes to improve window clearing operation. Recirculation will be disabled automatically if these modes are selected. • If the recirculation button is pressed while in the Mix or Defrost mode, the indicator light in the recirculation button will flash 3 times indicating that recirculation is not allowed.
UNDERSTANDING YOUR INSTRUMENT PANEL • Press the recirculation button until the indicator light remains lit. • The selection will be stored when the ignition switch is turned OFF or if the “POWER” button is pressed. If the recirculation indicator light is lit, the recirculation mode will not reset when the engine is started. If the recirculation indicator light is not lit, the recirculation mode will reset to the outside air mode when the engine is started.
UNDERSTANDING YOUR INSTRUMENT PANEL • The selection will be stored when the ignition switch is turned OFF or if the “POWER” button is pressed. front seat occupant comfort, even under changing outside weather conditions. If the recirculation indicator light is lit, the recirculation mode is enabled. If the recirculation indicator light is not lit, the recirculation mode is OFF. The programmed status can be changed back and forth by following the above mentioned procedure.
UNDERSTANDING YOUR INSTRUMENT PANEL To operate the system, press either the ⬙AUTO HI⬙ or ⬙AUTO LO⬙ buttons. The system now automatically regulates the heating and air conditioning system including blower speed, outlet air temperature, and airflow distribution through the various outlets within the instrument panel. Using the ⬙TEMP⬙ buttons, adjust the temperature you would like the system to maintain. When the system is set to your comfort level, it is not necessary to change the settings.
UNDERSTANDING YOUR INSTRUMENT PANEL This feature may be disabled using the following procedure: • Press and hold the Heated Rear Window and Auto LO buttons for 5 seconds. • The “DELAY” symbol will flash to indicate that the feature as been disabled. This feature may be enabled using the following procedure: • Press and hold the Heated Rear Window and Auto HI buttons for 5 seconds. • The “DELAY” symbol will flash to indicate that the feature as been enabled.
UNDERSTANDING YOUR INSTRUMENT PANEL Manual Operation This system offers a full complement of manual override features. The indicator light in both the ⬙AUTO HI⬙ or ⬙AUTO LO⬙ buttons will turn off when the system is being used in the manual mode. The fan speed, airflow distribution, and outside air/recirculated air can be manually adjusted. NOTE: Each of these features operate independently from each other.
UNDERSTANDING YOUR INSTRUMENT PANEL Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. Moving the knob up, down, left, or right will direct the air accordingly. The thumbwheel next to each outlet can be rotated to reduce or shut off the air flow from these outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 Air comes from both the instrument panel outlets and floor outlets. A slight amount of air is also directed through the defrost and side window demister outlets. Bi-Level Mode NOTE: In many temperature positions, the bi-level mode is designed to provide cooler air out of the panel outlets and warmer air from the floor outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL Floor Mode Mix Mode Floor Outlets Mix Outlets Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Air comes from the floor, defrost and side window demist outlets. This mode is not used when operating in either ⬙AUTO HI⬙ or ⬙AUTO LO⬙. This mode should be used when airflow to the floor and windshield is desired.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 NOTE: While operating in ⬙AUTO HI⬙ or ⬙AUTO LO⬙, the system will not automatically sense the presence fog, mist, or ice on the windshield. The defrost button must be pressed to clear the windshield and side glass. Defrost Mode Depress the “A/C” button to turn on and off the air conditioning during manual operation only. Cool dehumidified air comes through the outlets selected by the Mode Control.
UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation Control When the outside air contains smoke, odors, high humidity, or if rapid cooling is desired you may wish to recirculate interior air by pressing the recirculation button. The recirculation mode should only be used temporarily. The recirculate symbol will illuminate in the display when this button is selected. Push the button a second time to allow outside air into the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL The recirculation control is now programmed so that the recirculation mode will not reset to the outside air mode when the engine is restarted. The recirculation programming can be changed back by repeating this procedure. Rear Fan Operation To operate the rear fan, press the ⬙REAR⬙ button. The first time this button is pressed the ⬙REAR AUTO⬙ display will illuminate indicating that the rear fan speed is automatically controlled.
UNDERSTANDING YOUR INSTRUMENT PANEL Winter Operation To insure the best possible heater and defroster performance, make sure the engine cooling system is functioning properly and the proper amount, type, and concentration of coolant is used. Refer to section 7, Maintenance Procedures, of this manual for proper coolant selection. Use of the air Recirculation mode during winter months is not recommended because it may cause window fogging.
UNDERSTANDING YOUR INSTRUMENT PANEL A/C Air Filter The climate control system filters out dust, pollen and some odors from the air. Strong odors can not be totally filtered out. Refer to section 7 “Air Conditioning” for filter replacement instructions. Outside Temperature Display The outside temperature can be shown in the ATC display by pressing the ⬙OUTSIDE TEMP⬙ button.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . . 248 ▫ AutoStick Operation . . . . . . . . . . . . . . . . . . . 254 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 248 ▫ AutoStick General Information . . . . . . . . . . . . 254 䡵 Engine Block Heater — If Equipped . . . . . . . . . 250 䡵 All Wheel Drive — If Equipped . . . . . . . . . . . . 255 䡵 Automatic Transmission . . . . . . . . . . . . . . . . . . 251 䡵 Parking Brake . . . . . . . .
STARTING AND OPERATING ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 263 䡵 All Wheel Drive (AWD) — If Equipped . . . . . . . 281 ▫ Tire Identification Number (TIN) . . . . . . . . . . 267 䡵 Tire Pressure Monitor System — If Equipped . . . 281 ▫ Tire Loading And Tire Pressure . . . . . . . . . . . 268 ▫ 1,2,3, Or 4 Tire(s) Low Pressure . . . . . . . . . . . 282 䡵 Tires—General Information . . . . . . . . . . . . . . . . 272 ▫ 1,2,3, Or 4 Tire(s) High Pressure . . . . . . . . .
STARTING AND OPERATING 247 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . . 288 ▫ Gross Axle Weight Rating (GAWR) . . . . . . . . . 292 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . . 289 ▫ Overloading . . . . . . . . . . . . . . . . . . . . . . . . . 293 ▫ Fuel System Cautions . . . . . . . . . . . . . . . . . . 289 ▫ Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . . . 290 䡵 Trailer Towing . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES CAUTION! Long periods of engine idling, especially at high engine speeds, can cause excessive exhaust temperatures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. WARNING! Do not leave animals or children inside parked vehicles in hot weather; interior heat build up may cause serious injury or death. The gear selector must be in the NEUTRAL or PARK position before you can start the engine.
STARTING AND OPERATING WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly.
STARTING AND OPERATING the floor. Release the accelerator pedal and the key once the engine is running smoothly. Do not overspeed engine. If the engine shows no sign of starting after two 15 second periods of cranking with the accelerator pedal held to the floor, the “NORMAL STARTING” procedure should be repeated. After Starting The idle speed will automatically decrease as the engine warms up.
STARTING AND OPERATING AUTOMATIC TRANSMISSION CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed.
STARTING AND OPERATING Automatic Transmission Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK. It also prevents shifting out of PARK unless the key is in the ACCESSORY or ON position. NOTE: If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.
STARTING AND OPERATING NOTE: Even if the transmission can be reset, it is recommended that you visit a dealer at your earliest possible convenience. Your dealer has diagnostic equipment to determine if the problem could recur. If the transmission cannot be reset, dealer service is required. Gear Ranges DO NOT race the engine when shifting from PARK or NEUTRAL positions into another gear range. “P” Park Supplements the parking brake by locking the transmission. The engine can be started in this range.
STARTING AND OPERATING AUTOSTICK Autostick is a driver-interactive transmission that offers manual gear shifting capability to provide you with more control. Autostick allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situations.
STARTING AND OPERATING • You can start out in first, second, or third gear. Shifting into fourth gear can occur only after vehicle speed reaches 15 mph (24 km/h). • The transmission will automatically downshift to first gear when coming to a stop. • Starting out in third gear is helpful in snowy or icy conditions. • While in the Autostick mode, Speed Control will only function in third or fourth gear. Downshifting out of third gear will turn off the speed control.
STARTING AND OPERATING CAUTION! All wheels must have the same size and type tires. Unequal tire sizes must not be used. Unequal tire size may cause failure of the power transfer unit and/or the viscous coupling. Before leaving the vehicle, make sure that the parking brake is fully applied and place the gear selector in the Park position. To release the parking brake, pull out on the parking brake release located on the left side of the instrument panel.
STARTING AND OPERATING When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the transmission locking mechanism may make it difficult to move the selector out of park. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on a uphill grade. The parking brake should always be applied when the driver is not in the vehicle.
STARTING AND OPERATING BRAKE SYSTEM In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be much greater than that required with the power system operating. Your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems lose normal capability, the remaining system will still function.
STARTING AND OPERATING WARNING! • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING When the vehicle is driven over 7 mph (11 km/h), you may also hear a slight clicking sound as well as some related motor noises. These noises are the system performing its self check cycle to ensure that the ABS system is working properly. This self check occurs each time the vehicle is started and accelerated past 7 mph (11 km/h). • and a slight drop or fall away of the brake pedal at the end of the stop.
STARTING AND OPERATING POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason, the power assist is interrupted, it will still be possible to steer your vehicle. Under these conditions you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.
STARTING AND OPERATING TRACTION CONTROL — IF EQUIPPED The Traction Control System reduces wheel slip and maintains traction at the driving (front) wheels. The system reduces wheel slip by engaging the brake on the wheel that is losing traction (spinning). The system will operate at speeds below 35 mph (56 km/h).
STARTING AND OPERATING NOTE: • The Traction Control system will make buzzing or clicking sounds when in operation. 263 TIRE SAFETY INFORMATION Tire Markings • Extended heavy use of Traction Control may cause the system to deactivate and turn on the traction control indicator located in the instrument cluster. This is to prevent overheating of the brake system and is a normal condition. The system will remain disabled for about 4 minutes until the brakes have cooled.
STARTING AND OPERATING • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • Temporary Spare tires are high pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
STARTING AND OPERATING 265 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (ie. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. 267 Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure for passenger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar. For vehicles other than passenger cars, the cold tire inflation pressures are listed on either the “B” pillar, the Certification Label or in the Tire Inflation Pressures brochure in the glove compartment.
STARTING AND OPERATING Tire and Loading Information Placard 269 4) the cold tire inflation pressures for the front, rear and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
STARTING AND OPERATING lbs.” on the Tire and Loading Information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. Steps for Determining Correct Load Limit 6.
STARTING AND OPERATING 271 5
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 273 Some vehicles may have Supplemental Tire Pressure Information for vehicle loads that are less than the maximum loaded vehicle condition.
STARTING AND OPERATING The pressure should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are underinflated. CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap–if equipped.
STARTING AND OPERATING Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important.
STARTING AND OPERATING Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Always use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels). Never combine them with other types of tires. Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
STARTING AND OPERATING Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result.
STARTING AND OPERATING WARNING! WARNING! The limited use spare tires are for emergency use only. Installation of this limited use spare tire affects vehicle handling. With this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly. Replace (or repair) the original tire at the first opportunity and reinstall it on your vehicle.
STARTING AND OPERATING These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point. 279 Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that Replacing original tires with tires of a different size may result in false speedometer and odometer readings. specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.
STARTING AND OPERATING Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. ALL WHEEL DRIVE (AWD) — IF EQUIPPED CAUTION! All Wheel Drive (AWD) vehicles must have the same size and type tires on all wheel positions. Unequal tire sizes must not be used. Unequal tire size may cause failure of the power transfer unit and/or the viscous coupling.
STARTING AND OPERATING 1,2,3, OR 4 TIRE(S) LOW PRESSURE Low tire pressure levels of 26 psi [1.79 bars] (179 kPa) or less detected in one or more tires. Inspect all tires for proper inflation pressure, once the proper tire pressure has been set, the TPM system warning will reset automatically when the vehicle has been driven for at least 2 minutes at or above 20 mph (32 km/h). 1,2,3, OR 4 TIRE(S) HIGH PRESSURE High tire pressure levels of 45 psi [3.
STARTING AND OPERATING CAUTION! The TPM system has been optimized for the original equipment tires and wheels. TPM system pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. After-market wheels can cause sensor damage. Do not use tire sealant or balance beads if your vehicle is equipped with a TPM system, as damage to the sensors may result.
STARTING AND OPERATING General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. The tire pressure sensors are covered under one of the following licenses: United States . . . . . . . . . . . . . . . . . . . . . KR5S120123 Canada . . . . . . . . . .
STARTING AND OPERATING CAUTION! To avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious damage. Stop the vehicle immediately if noise occurs that could indicate chain breakage. Remove the damaged parts of the chain before further use.
STARTING AND OPERATING Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear patterns.
STARTING AND OPERATING FUEL REQUIREMENTS Your vehicle is designed to meet all emissions regulations and provide satisfactory fuel economy and performance when using high quality unleaded gasoline having an octane range of 87 to 89 or higher. The manufacturer recommends the use of 89 octane for optimum performance. Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required.
STARTING AND OPERATING Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as 10% ethanol, MTBE, and ETBE. Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle. CAUTION! DO NOT use gasolines containing Methanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components.
STARTING AND OPERATING Materials Added to Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives are not needed under normal conditions and would result in additional cost. Therefore you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law.
STARTING AND OPERATING Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
STARTING AND OPERATING CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. 291 Malfunction Indicator Light in the instrument cluster will turn on. Make sure that the gas cap is tightened each time the vehicle is refueled. • When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
STARTING AND OPERATING VEHICLE LOADING The load carrying capacity of your vehicle is shown in the charts that follow. This information should be used for passenger and luggage loading as indicated. • Vehicle Identification Number (VIN) If the seatbacks are folded for carrying cargo, do not exceed the specified GVWR and GAWR. The bar code allows a computer scanner to read the Vehicle Identification Number (VIN).
STARTING AND OPERATING WARNING! Because the front wheels drive and steer the vehicle, it is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. Overloading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and front and rear GAWR.
STARTING AND OPERATING A loaded vehicle is shown in the illustration. Note that neither the GVWR or the GAWR capacities have been exceeded.
STARTING AND OPERATING 295 To maintain warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing. Towing Requirements Perform maintenance services as prescribed in the maintenance schedules manual.
STARTING AND OPERATING • Do not attempt to tow a trailer while using a compact spare tire. • Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are recommended for motoring safety. • The automatic transmission fluid and filter should be changed if you REGULARLY tow a trailer for more than 45 minutes of continuous operation. See Schedule “B” in section 8 of this manual for transmission fluid change intervals.
STARTING AND OPERATING TRAVEL CONDITION UP TO 2 PERSONS & LUGGAGE 3 TO 4 PERSONS & LUGGAGE 5 TO 6 PERSONS & LUGGAGE MAXIMUM TRAILER WEIGHT Trailer Frontal Area Not To Exceed 40 Square Feet (3.72 Square Meters) 3.5/3.8L ENGINES MAX.
STARTING AND OPERATING WARNING! Connecting trailer brakes to your vehicle’s hydraulic brake lines can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the ground) Recreational towing for this vehicle is not recommended. NOTE: If the vehicle requires towing make sure all four wheels are off the ground.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 300 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . . 301 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . 312 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . . 302 䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . . 313 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The hazard flasher switch is located in the center of the instrument panel above the center air outlets. To engage the Hazard Warning Flashers, depress the switch on the instrument panel. When the Hazard Warning Switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Push the switch a second time to turn off the flashers.
WHAT TO DO IN EMERGENCIES IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. • On the highways — Slow down. • In city traffic — While stopped, put transmission in neutral, but do not increase engine idle speed. NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off.
WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7, Maintenance, of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. JACKING AND TIRE CHANGING WARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you.
WHAT TO DO IN EMERGENCIES Jack Location Five Passenger Seating The jack and jack-handle are stowed in the rear storage bin located behind the second row bench seat. Pull up on the storage bin cover to access the jack and jack tools. 303 Remove the scissors jack and jack handle by rotating the small wing nut to the left.
WHAT TO DO IN EMERGENCIES Six Passenger Seating The jack and jack-handle are stowed in the rear storage bin located in the rear cargo floor. Pull up on the storage bin cover and liner to access the jack and jack tools. Spare Tire Stowage Five Passenger Seating The spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. To remove or stow the spare, use the jack handle to rotate the “spare tire drive” nut.
WHAT TO DO IN EMERGENCIES 305 CAUTION! The winch mechanism is designed for use with the jack handle only. Use of an air wrench or other power tools is not recommended and can damage the winch. When the spare is clear, tilt the retainer at the end of the cable and pull it through the center of the wheel. Lowering Spare Tire Spare Tire Removal Fit the jack-handle over the drive nut.
WHAT TO DO IN EMERGENCIES WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • Turn on the Hazard Warning Flasher. • Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if changing the right front tire, block the left rear wheel. • Passengers should not remain in the vehicle when the vehicle is being jacked.
WHAT TO DO IN EMERGENCIES 307 location. Do not raise the vehicle until you are sure the jack is securely engaged. Never jack up the vehicle using any suspension components. 6. Raise the vehicle by turning the jack screw to the right, using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. WARNING! Jack Engagement Locations 5.
WHAT TO DO IN EMERGENCIES 7. Remove the wheel lug nuts, for vehicles with wheel covers, remove the cover from the wheel by hand. Do not pry the wheel cover off. Then pull the wheel off the hub. 8. Install the spare wheel, for vehicles with wheel covers, align the notch in the wheel cover with the valve stem on the wheel. Install the cover on the wheel by hand only and install the wheel lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts.
WHAT TO DO IN EMERGENCIES • Turn the wheel so that the valve-stem is down. Slide the wheel retainer through the center of the wheel and position it properly across the wheel opening. • For convenience in checking the spare tire inflation, stow with the valve-stem toward the rear of the vehicle. • Using the jack-handle, rotate the drive nut to the right until the wheel is drawn into place against the underside of the vehicle. • Continue to rotate the nut until you hear the mechanism click three times.
WHAT TO DO IN EMERGENCIES WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from another vehicle. This type of start can be dangerous if done improperly, so follow this procedure carefully.
WHAT TO DO IN EMERGENCIES 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. 6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan.
WHAT TO DO IN EMERGENCIES 2. Slow down if road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the vehicle in front to avoid a collision in a sudden stop. FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels.
WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE With Ignition Key Front Wheel Drive Your vehicle may be towed under the following conditions: The gear selector must be in NEUTRAL, the distance to be traveled must not exceed 100 miles (160 km), the towing speed must not exceed 44 mph (72 km/h), and both front and rear wheels must be on the ground. Exceeding these towing limits may cause a transmission geartrain failure.
WHAT TO DO IN EMERGENCIES All Transmissions CAUTION! • Do not attempt to tow this vehicle from the front with sling type towing equipment. Damage to the front fascia will result. • Always use wheel lift equipment when towing from the front. The only other approved method of towing is with a flat bed truck. • Do not tow the vehicle from the rear. Damage to the rear sheet metal, liftgate and fascia will occur.
WHAT TO DO IN EMERGENCIES 315 TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE WITH A TOW DOLLEY The manufacturer does not recommend that you tow an All-Wheel Drive (AWD) or front wheel drive vehicle on a tow dolley. Vehicle damage may occur.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 3.5L Engines . . . . . . . . . . . . . . . . . . . . . . . . . . 320 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 326 䡵 3.8L Engines . . . . . . . . . . . . . . . . . . . . . . . . . . 321 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . . 330 䡵 Onboard Diagnostic System — OBD II . . . . . . . . 322 ▫ Drive Belts — Check Condition And Tension . . 330 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . . 323 ▫ Spark Plugs . . . . .
MAINTAINING YOUR VEHICLE ▫ Air Conditioner Maintenance . . . . . . . . . . . . . 335 ▫ Power Steering — Fluid Check . . . . . . . . . . . . 336 ▫ Front & Rear Suspension Ball Joints . . . . . . . . 337 ▫ Steering Shaft Seal . . . . . . . . . . . . . . . . . . . . 337 ▫ Steering Linkage . . . . . . . . . . . . . . . . . . . . . . 337 ▫ Drive Shaft Universal Joints . . . . . . . . . . . . . . 337 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . . 338 ▫ Windshield Wiper Blades . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ High Intensity Discharge Headlights (HID) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 365 ▫ Front Park/Turn Signal And Sidemarker Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366 ▫ Front Fog Light . . . . . . . . . . . . . . . . . . . . . . 366 ▫ Rear Tail, Stop, Turn Signal, Side Marker And Back-Up Lights . . . . . . . . . . . . . . . . . . . . . . . 367 319 ▫ License Light . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 3.5L ENGINES Engine Compartment 3.
MAINTAINING YOUR VEHICLE 321 3.8L ENGINES 7 Engine Compartment 3.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE Loose Fuel Filler Cap Message After fuel is added, the vehicle diagnostic system can determine if the fuel filler cap is loose, improperly installed, or damaged. A loose fuel filler cap message will be displayed in the instrument cluster. Tighten the gas cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off.
MAINTAINING YOUR VEHICLE Your vehicle has a simple ignition key actuated test which you can use prior to going to the test station. To check if your vehicle’s OBD system is ready, you must do the following: 1. Insert your ignition key into the ignition switch. 2. Turn the ignition to the ON position, but do not crank or start the engine. 3. If you crank or start the engine, you will have to start this test over. 4.
MAINTAINING YOUR VEHICLE Regardless of whether your vehicle’s OBD system is ready or not ready, if the MIL symbol is illuminated during normal vehicle operation, you should have your vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL symbol is on with the engine running. REPLACEMENT PARTS Use of genuine Mopar威 parts for normal/scheduled maintenance and repairs is highly recommended to insure the designed performance.
MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle.
MAINTAINING YOUR VEHICLE 327 Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to see if any apply to you. • Day or night temperatures are below 32°F (0°C). • Stop and Go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). Engine Oil Dipstick CAUTION! Overfilling or underfilling will cause oil aeration or loss of oil pressure.
MAINTAINING YOUR VEHICLE NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual. If none of these apply to you, then change your engine oil at every interval shown on schedule ⬙A⬙ of the ⬙Maintenance Schedules⬙ section of this manual. NOTE: Under no circumstances should oil change intervals exceed 6000 miles (10 000 km) or 6 months whichever comes first.
MAINTAINING YOUR VEHICLE 329 Engine Oil Viscosity (SAE Grade) — 3.8 Liter Engines SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. Refer to your engine oil filler cap for the recommended engine oil viscosity for your vehicle. For information on engine oil filler cap location, refer to the Engine Compartment illustration in this section. • SAE 10W-30 engine oil is preferred.
MAINTAINING YOUR VEHICLE Synthetic Engine Oils There are a number of engine oils being promoted as either synthetic or semi-synthetic. If you chose to use such a product, use only those oils that are American Petroleum Institute (API) Certified and have the recommended SAE viscosity grade. Follow the maintenance schedule that describes your driving type.
MAINTAINING YOUR VEHICLE Belts should be inspected for evidence of cuts, cracks, or glazing, and replaced if there is indication of damage which could result in belt failure. Low generator belt tension can cause battery failure. Also check belt routing to make sure there is no interference between the belts and other engine components. Spark Plugs Spark plugs must fire properly to assure engine performance and emission control. New plugs should be installed at the specified mileage.
MAINTAINING YOUR VEHICLE Fuel Filter A plugged fuel filter can cause stalling, limit the speed at which a vehicle can be driven or cause hard starting. Should an excessive amount of dirt accumulate in the fuel tank, filter replacement may be necessary. See your local dealer for service. Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device.
MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may indicate severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a system performance check. Drive belt tension should also be checked at this time. 335 WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system.
MAINTAINING YOUR VEHICLE Refrigerant Recovery And Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment. NOTE: Use only manufacturer approved A/C System Sealers, Stop Leak Products, Seal Conditioners, Compressor Oil, or Refrigerants.
MAINTAINING YOUR VEHICLE WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Recommended Fluids, Lubricants, and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE Continued operation could result in failure of the universal joint due to water and dirt contamination of the grease. This would require complete replacement of the joint assembly. The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of a high quality lubricant such as Mopar威 Lock Cylinder Lubricant directly into the lock cylinder.
MAINTAINING YOUR VEHICLE 339 Windshield and Rear Window Washers The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the engine compartment and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water. The washer fluid reservoir will hold a full gallon of fluid when the Low Washer Fluid Light illuminates.
MAINTAINING YOUR VEHICLE Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment.
MAINTAINING YOUR VEHICLE Coolant Checks Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser.
MAINTAINING YOUR VEHICLE CAUTION! Mixing of coolants other than specified HOAT engine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible. Do not use plain water alone or alcohol base engine coolant (antifreeze) products.
MAINTAINING YOUR VEHICLE The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated. NOTE: Mixing coolant types will decrease the life of the engine coolant and will require more frequent coolant changes.
MAINTAINING YOUR VEHICLE Disposal of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately.
MAINTAINING YOUR VEHICLE • Do not overfill the coolant recovery bottle. • Check coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze needs to be added, contents of coolant recovery bottle must also be protected against freezing. • If frequent coolant additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks.
MAINTAINING YOUR VEHICLE Insure nylon tubing in these areas has not melted or collapsed. WARNING! Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present. Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency.
MAINTAINING YOUR VEHICLE Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present. NOTE: Often, fluid such as oil, power steering fluid, and brake fluid are used during assembly plant operations to facilitate the assembly of hoses to couplings. Therefore, oil wetness at the hose-coupling area is not necessarily an indication of leakage.
MAINTAINING YOUR VEHICLE Clean the top of the master cylinder area before removing the cap. Add fluid to bring the level up to the top of the “FULL” mark on the side of the master cylinder reservoir. Overfilling of fluid is not recommended because it may cause leaking in the system. Add enough fluid to bring the level up to the requirements described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear.
MAINTAINING YOUR VEHICLE CAUTION! Do not allow petroleum base fluid to contaminate the brake fluid, all brake seal components could be damaged causing partial or complete brake failure. Fuel System Hoses Electronic Fuel Injection high pressure fuel systems are designed with hoses and quick connect fittings which have unique material characteristics to provide adequate sealing and resist attack by deteriorated gasoline.
MAINTAINING YOUR VEHICLE Genuine Parts for correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid. CAUTION! Using a transmission fluid other than the manufacturers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes.
MAINTAINING YOUR VEHICLE 3. Fully apply parking brake. 4. Place the gear selector momentarily in each gear position ending with the lever in P (PARK). Wipe the area around the dipstick clean to eliminate the possibility of dirt entering the transmission. 5. Remove the dipstick and determine if the fluid is hot or warm. Hot fluid is approximately 180°F (82°C), which is the normal operating temperature after the vehicle has been driven at least 15 miles (24 km).
MAINTAINING YOUR VEHICLE Severe Usage (fluid and filter) — Refer to Maintenance Schedule “B” Severe Usage is defined as: • Police, taxi, limousine, commercial type operation, or trailer towing where the vehicle driven regularly for more than 45 minutes of continuous operation. NOTE: Refer to Section 8 of this manual for Maintenance Schedules. If the transmission is disassembled for any reason, the fluid and filter should be changed. Special Additives Do not add any fluid additives to the transmission.
MAINTAINING YOUR VEHICLE Overrunning Clutch The fill plug is located on the side of the overrunning clutch housing. The fluid should be maintained at a level even with the bottom of the fill plug hole when the vehicle is parked on a level surface. If it becomes necessary to add or replace the fluid, use only the manufacturers recommended transmission fluid, refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE NOTE: Refer to Section 8 of this manual for Maintenance Schedules. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. Front And Rear Wheel Bearings Front and rear wheel bearings are permanently sealed. No regular maintenance is required for these components. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.
MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar or other similar deposits have accumulated on your vehicle, wash it as soon as possible. • Use Mopar auto polish to remove road film and stains and to polish your vehicle. Take care never to scratch the paint.
MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. • All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned regularly with mild soap and water to prevent corrosion. To remove heavy soil, select a nonabrasive, non-acidic cleaner.
MAINTAINING YOUR VEHICLE 357 Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar Total Clean. Care should be taken to avoid soaking your leather upholstery with any liquid.
MAINTAINING YOUR VEHICLE 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water.
MAINTAINING YOUR VEHICLE INTEGRATED POWER MODULE (IPM) Cavity 1 2 3 4 5 6 Integrated Power Module (IPM) An Integrated Power Module is located in the engine compartment near the battery. This center contains maxi fuses, mini fuses and relays. A label that identifies each component is printed on the inside of the cover.
MAINTAINING YOUR VEHICLE Cavity 10 11 12 13 14 15 40 41 42 Maxi Fuse Spare 40 Amp Green Spare 40 Amp Green Spare 40 Amp Green 40 Amp Green 40 Amp Green 40 Amp Green Description Headlight Washer, Power Liftgate Cavity 24 25 Radiator Fan 1 Anti-Lock Brake System (ABS) Module Driver Door Node Passenger Door Node 26 27 28 29 Front Blower 30 31 Mini Fuse Description 20 Amp Yel- Power Outlet (Selectable) low 15 Amp Blue Radio, Amplifier, Navigation, Hands-Free Phone (HFM), Electronic Vehicle Informa
MAINTAINING YOUR VEHICLE Cavity 34 35 36 37 38 39 44 45 46 Mini Fuse Spare Spare 20 Amp Yellow 25 Amp Natural 20 Amp Yellow 20 Amp Yellow 25 Amp Natural 10 Amp Red 20 Amp Yellow Description Cavity 47 Electronic Automatic Transaxle (EATX) Solenoid ASD 48 Fuel Pump 49 A/C Clutch, MTV 50 Rear Heated Seats Anti-Lock Brake System (ABS) Ignition Run Passenger Door 361 Mini Fuse Description 20 Amp Yel- Driver Door low 15 Amp Blue PLG, OHC, Body Control Module (BCM), Navigation, Hands-Free Phone (HFM)
MAINTAINING YOUR VEHICLE CAUTION! • When installing the Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Bulb Number Center & Rear Reading Lights . . . . . . . . . . . . . . . 578 Front Door Courtesy Light . . . . . . . . . . . . . . . . . . 578 Liftgate Light(s). . . . . . . . . . . . . . . . . . . . . . . . . . 578 Overhead Console Reading Lights . . . . . . . . . . . 212–2 Visor Vanity Lights. . . . . . . . . . . . . . . . . . . . . V26377 NOTE: For lighted switches, see your dealer for replacement instructions.
MAINTAINING YOUR VEHICLE BULB REPLACEMENT 2. Remove the rubber boot seals. Standard Quad Headlights 3. Disconnect the electrical connector. 1. Remove the two screws securing the headlight module to the vehicle and pull the headlight module forward away from the vehicle, disengaging the assembly from the lower attachment clip. 4. Rotate the bulb to the left and replace the bulb. Reinstall the rubber boot seals and then the headlight module. CAUTION! Do not touch the new bulb with your fingers.
MAINTAINING YOUR VEHICLE High Intensity Discharge Headlights (HID) — If Equipped The headlights are a type of high voltage discharge tube. High voltage can remain in the circuit even with the headlight switch off and the key removed. Because of this, you should not attempt to service a headlight bulb yourself. If a headlight bulb fails, take your vehicle to an authorized dealer for service.
MAINTAINING YOUR VEHICLE Front Park/Turn Signal and Sidemarker Lights 1. Remove the two screws securing the headlight module to the vehicle and pull the headlight module forward away from the vehicle, disengaging the assembly from the lower attachment clip. 3. Replace the bulb, reinstall the socket and then reinstall the headlight module. Front Fog Light 1. Reach under the front fascia and grasp the front fog light bulb. 2. Twist the front fog light bulb to remove from the fog light module. 3.
MAINTAINING YOUR VEHICLE 367 Rear Tail, Stop, Turn Signal, Side Marker and Back-up Lights 3. Twist the socket assembly to remove it from the housing. 1. Raise the liftgate. 4. Pull the bulb out of the socket. 2. Remove the two tail light assembly screws and rotate the assembly outward to remove the ball stud form the attaching grommet. 5. Replace the bulb, reinstall the socket, and reattach the tail light assembly. License Light 1.
MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel (approximate) 89 Octane Engine Oil-With Filter 3.5 Liter Engines (SAE 10W-30, API Certified) 3.8 Liter Engines (SAE 5W-20, API Certified) U.S. 23 gallons Metric 87 liters 5.5 qts 5.0 qts 5.2 liters 4.7 liters 10.7 qts 10.1 liters 11.8 qts 11.2 liters Cooling System * 3.5 Liter Engines (Mopar威 Antifreeze/Coolant 5 Year/ 100,000 Mile Formula or equivalent) 3.
MAINTAINING YOUR VEHICLE 369 RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant 3.5 Liter Engine Oil 3.8 Liter Engine Oil Spark Plugs Oil Filter, 3.5/3.8 Liter Engines Fuel Selection Fluids, Lubricants and Genuine Parts Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent Use API Certified SAE 10W-30 engine oil, refer to oil viscosity chart for correct SAE grade meeting DaimlerChrysler Material Standard MS-6395.
MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission AWD Power Transfer Unit AWD Overrunning Clutch AWD Rear Carrier Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts Mopar威 ATF+4 Automatic Transmission Fluid or equivalent. Mopar威 Gear Lubricant 75W-90 or equivalent. Mopar威 ATF+4 Automatic Transmission Fluid or equivalent. Mopar威 Gear Lubricant 75W-90 or equivalent. Mopar威 DOT 3 and SAE J1703 should be used.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . . . 372 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 375 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . . 372 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 372 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES • Taxi, police, or delivery service (commercial service).〫 • Off-road or desert operation. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙Maintenance Schedules⬙ section of this manual. NOTE: Most vehicles are operated under the conditions listed for Schedule ⬙B⬙. Second is Schedule “A”.
M A I N T E N A N C E S C H E D U L E S 8 374 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check tire pressure and look for unusual wear or damage. • Change the engine oil filter. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of coolant bottle, brake master cylinder and transmission, add as needed. • Check all lights and all other electrical items for correct operation. • Inspect the exhaust system. • Inspect the brake hoses.
SCHEDULE “B” SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an 〫. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km).
M 376 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Rotate Tires N C Inspect the brake linings. E Inspect the engine air cleaner filter, replace if S C H E D U L E S 8 necessary. * Replace the engine air cleaner filter. * Change the All Wheel Drive (AWD) power transfer unit fluid. (See note at the end of this chart) Replace the air conditioning filter.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Inspect the PCV valve and replace as necessary.* Change the All Wheel Drive (AWD) power transfer unit fluid. (See note at the end of this chart) Change the All Wheel Drive (AWD) overrunning clutch and rear carrier fluid.
M 378 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter. A Rotate Tires N C Inspect the brake linings. E Inspect the engine air cleaner filter, replace if S C H E D U L E S 8 necessary. * Replace the engine air cleaner filter. * Change the All Wheel Drive power transfer unit fluid. (See the note at the end of this chart.) Change the All Wheel Drive (AWD) overrunning clutch and rear carrier fluid. (See note at the end of this chart) Replace the air conditioning filter.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Inspect the PCV valve and replace if necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Change the automatic transmission fluid and filter.
M 380 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the All Wheel Drive (AWD) power A transfer unit fluid. (See note at the end of this N chart) C E Change the All Wheel Drive (AWD) overrunS C H E D U L E S 8 ning clutch and rear carrier fluid. (See note at the end of this chart) Replace the air conditioning filter.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter Replace the spark plugs. Inspect the tie rod ends and boot seals. (Front & Rear) Check the PCV valve and replace if necessary. Not required if previously changed.* Inspect the serpentine drive belt, replace if necessary. ‡ Change the All Wheel Drive power transfer unit fluid.
M 382 SCHEDULE “B” A I N Miles T (Kilometers) E N Change the All Wheel Drive (AWD) overrunA ning clutch and rear carrier fluid. (See note at N the end of this chart) C E Replace the air conditioning filter.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter * Replace engine timing belt. Change the All Wheel Drive (AWD) power transfer unit fluid. (See note at the end of this chart) Change the All Wheel Drive (AWD) overrunning clutch and rear carrier fluid. (See note at the end of this chart) Inspect the serpentine drive belt, replace if necessary.
M 384 SCHEDULE “B” A I N Miles T (Kilometers) E N Flush and replace the engine coolant at 60 A months or 100,000 miles. N C Replace the air conditioning filter.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Inspect the PCV valve and replace as necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Change the automatic transmission fluid and filter. Change the All Wheel Drive (AWD) power transfer unit fluid.
M A I N T E N A N C E 386 SCHEDULE “B” * This maintenance is recommended by the manufacture to the owner but is not required to maintain the emissions warranty. ‡ This maintenance is not required if previously replaced. Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all reS ceipts.
SCHEDULE “A” 387 M SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Replace the air conditioning filter.
M 388 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate Tires E Inspect the brake linings. S C H E D U L E S 8 Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Check the PCV valve and replace, if necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Flush and replace the engine coolant at 60 months, regardless of mileage.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate Tires Inspect the brake linings. Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Inspect the tie rod ends and boot seals. (Front & Rear) Check and replace the PCV valve , if necessary.* Inspect the serpentine drive belt, replace if necessary. ‡ Replace the spark plugs. Flush and replace the engine coolant at 100,000 miles, if not done at 60 months.
M 390 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate Tires E Inspect the brake linings. S C H E D U L E S 8 Inspect the engine air cleaner filter, replace if necessary. * Replace the engine air cleaner filter. Replace engine timing belt. Inspect the tie rod ends and boot seals. (Front & Rear) Check the PCV valve and replace, if necessary.* Inspect the serpentine drive belt, replace if necessary.
SCHEDULE “A” * This maintenance is recommended by the manufacture to the owner but is not required to maintain the emissions warranty. ‡ This maintenance is not required if previously replaced. Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts. 391 M WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394 ▫ Prepare For The Appointment . . . . . . . . . . . . 394 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 394 䡵 Reporting Safety Defects . . . . . . . . . . . . . . . . . . 399 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 399 䡵 Publication Order Forms . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to you selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service. The manufacturer’s dealers have the facilities, factory-trained technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner.
IF YOU NEED CONSUMER ASSISTANCE In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico (915) 729–1248 or 729–1240 Outside Mexico (525) 729–1248 or 729–1240 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center.
IF YOU NEED CONSUMER ASSISTANCE The manufacturer will not stand behind any service contract that is not the manufacturer’s Service Contract. It is not responsible for any service contract other than the manufacturer’s Service Contract. If you purchased a service contract that is not a manufacturer’s Service Contract, and you require service after your manufacturer’s new vehicle limited warranty expires, please refer to your contract documents, and contact the person listed in those documents.
IF YOU NEED CONSUMER ASSISTANCE U.S.
IF YOU NEED CONSUMER ASSISTANCE MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.
IF YOU NEED CONSUMER ASSISTANCE Call Toll Free at 1–800–890–4038 (U.S.) or 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: www.techauthority.daimlerchrysler.com or www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration.
IF YOU NEED CONSUMER ASSISTANCE WARNING! WARNING! The traction grade is based on braking (straightahead) traction tests and does not include cornering (turning) performance. The temperature grade is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
INDEX 10
INDEX Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 290 Adding Washer Fluid . . . . . . . . . . . . . . . . . . 128,339 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 289 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 133 Air Conditioner Maintenance . . . . . . . . . . . . . . . 335 Air Conditioning . . . . . . . . . . . . . . . . . . . . . 223,228 Air Conditioning Controls . . . . . . . . . . . . . . . . . 223 Air Conditioning Filter . . . . . .
INDEX Selection Of Lubricant . . . . . . . . . . . . . . . . 349,370 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253 Special Additives . . . . . . . . . . . . . . . . . . . . . . 352 Automatic Transmission . . . . . . . . . . . . . . . . . . . 349 Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . 350 Fluid and Filter Changes . . . . . . . . . . . . . . . . . 351 Fluid Change . . . . . . . . . . . . . . . . . . . . . . . . . 351 Fluid Level Check . . . . . . . . . . . . .
INDEX Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355 Carbon Monoxide Warning . . . . . . . . . . . . . . . . . 290 Cargo Area Cover . . . . . . . . . . . . . . . . . . . . . . . 152 Cargo Compartment Luggage Carrier . . . . . . . . . . . . . . . . . . . . . . . 155 Cargo Tie-Downs . . . . . . . . . . . . . . . . . . . . . . . . 153 Cassette Tape and Player Maintenance . . . . . . . . . 220 Cassette Tape Player . . . . . . . . . . . . . . . . . . . 193,198 Catalytic Converter .
INDEX Adding Coolant (Antifreeze) . . . . . . . . . . . . . . 342 Coolant Capacity . . . . . . . . . . . . . . . . . . . . . . 368 Coolant Level . . . . . . . . . . . . . . . . . . . . . . 341,344 Disposal of Used Coolant . . . . . . . . . . . . . . . . 344 Drain, Flush, and Refill . . . . . . . . . . . . . . . . . . 341 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . 344 Points to Remember . . . . . . . . . . . . . . . . . . . . 344 Pressure Cap . . . . . . . . . . . . . . . . . . . . . .
INDEX DVD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 Electric Remote Mirrors . . . . . . . . . . . . . . . . . . . . 78 Electrical Power Outlets . . . . . . . . . . . . . . . . . . . 148 Electronic Speed Control . . . . . . . . . . . . . . . . . . . 134 Electronic Vehicle Information Center . . . . . . . . . 174 Emergency, In Case of Hazard Warning Flasher . . . . . . . . . . . . . . . . . 300 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302 Jump Starting .
INDEX Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 331 Air Conditioning . . . . . . . . . . . . . . . . . . . . 243,336 Automatic Transaxle . . . . . . . . . . . . . . . . . . . . 351 Engine Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 332 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . 330,369 Engine Oil Disposal . . . . . . . . . . . . . . . . . . . . 330 Flashers Hazard Warning . . . . . . . . . . . . . . . . . . . . . . . 300 Turn Signal . . . . . . . .
INDEX Garage Door Opener . . . . . . . . . . . . . . . . . . . . . 138 Gas Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . 290,323 Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287 Gasoline, Clean Air . . . . . . . . . . . . . . . . . . . . . . 287 Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . 288 Gauges Coolant Temperature . . . . . . . . . . . . . . . . . . . . 165 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Speedometer . .
INDEX Ignition Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . . 15 Immobilizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Indicator, Traction Control . . . . . . . . . . . . . . . . . 168 Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Information Center, Vehicle . . . . . . . . . . . . . . . . . 174 Instrument Cluster . . . . . . . . . . . . . . . . .
INDEX Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Automatic Headlights . . . . . . . . . . . . . . . . . . . 123 Back-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367 Brake Warning . . . . . . . . . . . . . . . . . . . . . . . . 167 Bulb Replacement . . . . . . . . . . . . . . . . . . . 363,364 Courtesy/Reading . . . . . . . . . . . . . . . . . . . . . 120 Cruise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 Daytime Running . . . . . . . . . .
INDEX Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . 293 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268 Locks Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Lower Anchors and Tether for CHildren (LATCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59,61 Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . 338 Luggage Rack . . . . . . . . . . . . . . . . . . . . . . . . . . 155 Maintenance, Airbag . . . . . . . . . . .
INDEX Occupant Restraints . . . . . . . . . . . . . . . . . . . . . . . 32 Octane Rating, Gasoline . . . . . . . . . . . . . . . . . . . 287 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . 326,369 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368 Change Interval . . . . . . . . . . . . . . . . . . . . . . . 327 Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326 Disposal . . . . . .
INDEX Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102,103 Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 Steering, Checking . . . . . . . . . . . . . . . . . . . . . 336 Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Restraint, Head . . . . . . . . . . . . . . . . . . . . . . . . . 104 Restraints, Child . . . . . . . . . . . . . . . . . . . . . . . 59,65 Restraints, Infant . . . . . . . . . . . . . . . . . . . . . . . . . 62 Retractable Cargo Area Cover . . . . . . . . . . . . . . . 152 Rocking Vehicle When Stuck . . . . . . . . . . . . . . . . 312 Roof Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 Rotation, Tires . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Security Alarm (Theft Alarm) . . . . . . . . . . . . . . . . 25 Selection of Coolant . . . . . . . . . . . . . . . . . . . 341,369 Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Sentry Key Programming . . . . . . . . . . . . . . . . . . . 14 Service Assistance . . . . . . . . . . . . . . . . . . . . . . . 394 Service Contract . . . . . . . . . . . . . . . . . . . . . . . . . 396 Service Engine Soon Light (Malfunction Indicator) . 170 Service Manuals . . . . . . . . . . . . .
INDEX System, Navigation . . . . . . . . . . . . . . . . . . . . . . 222 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 Tape Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 Temperature Control, Automatic . . . . . . . . . . . . . 232 Temperature Gauge, Engine Coolant . . . . . . . 165,301 Tether Anchor, Child Restraint . . . . . . . . . . . . . 59,61 Theft Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Theft System . . . . . . . . . . . . .
INDEX Tread Wear Indicators . . . . . . . . . . . . . . . . . . . 278 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294 Disabled Vehicle . . . . . . . . . . . . . . . . . . . . . . . 313 Recreational . . . . . . . . . . . . . . . . . . . . . . . 298,314 Trailering . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294 Traction Control . . . . . . . . . . . . . . . . . . . 130,168,262 Traction Control Switch . . . . . . . . . . . . . . . . . 130,262 Trailer Towing . . . . . . . .
INDEX Vehicle Certification Label . . . . . . . . . . . . . . . . . 292 Vehicle Identification Number . . . . . . . . . . . . . . . . 6 Vehicle Loading . . . . . . . . . . . . . . . . . . . 269,292,293 Vehicle Modifications/Alterations . . . . . . . . . . . . . . 7 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . 242,362 Vehicle Theft Alarm . . . . . . . . . . . . . . . . . . . . . . . 25 Video Entertainment System . . . . . . . . . . . . . . . . 203 Warning Flasher, Hazard . . . . . . .