SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your Crossfire. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 9 ▫ Start Lockout . . . . . . . . . . . . . . . . . . . . . . . . .14 ▫ Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 䡵 Remote Keyless Entry . . . . . . . . . . . . . . . . . . . .14 ▫ Obtaining Replacement Keys . . . . . . . . . . . . . .10 ▫ To Unlock The Doors . . . . . . . . . . . . . . . . . . .14 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 䡵 Power Windows . . . . . . . . . . . . . . . . . . . . . . . .21 ▫ Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .40 ▫ Power Window Operation With The Convertible Top Switch (Roadster Only) . . . . . . . . . . . . . . .22 䡵 Engine Break-In Recommendations . . . . . . . . . .47 䡵 Rear Liftgate/Decklid Release . . . . . . . . . . . . . .22 䡵 Occupant Restraints . . . . . . . . . . . . . . . . . . . . .22 ▫ Lap/Shoulder Belts . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS You can insert the double-sided keys into the locks with either side up. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys only from an authorized dealer. Ask your dealer for these numbers and keep them in a safe place. CAUTION! An unlocked car is an invitation to thieves.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Obtaining Replacement Keys Your vehicle is equipped with a theft deterrent locking system requiring a special key manufacturing process. For security reasons, replacement keys can only be obtained from your authorized dealer. Important! Removing the key from the steering lock activates the start lock-out. The engine cannot be started. Turning the key in the steering lock to the ON/RUN position deactivates the start lock-out.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE GLOVE COMPARTMENT LOCK The glove compartment can be locked by turning the key straight up to the vertical or right position, and then removing the key. To unlock the glove compartment, turn the key to the horizontal or left position, and then remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The doors can be unlocked by pulling on the inside door handle, pressing and releasing the top portion of the central locking switch located in the console, or by pressing and releasing the Unlock transmit button on the key fob. Both doors can also be unlocked by turning the key counterclockwise in the driver’s door. NOTE: In case of a malfunction in the central locking system, the doors can be locked and unlocked individually.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: The fuel filler door and center console (roadster only) cannot be locked or unlocked with the central locking switch. NOTE: If you attempt to lock the doors with the key in the ignition and the driver’s door open, the doors will not lock. Automatic Central Locking The central locking switch also operates the automatic central locking feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Perform the quick system check which follows: Use the remote transmitter to set the alarm. If the parking lamps flash three times, the system is operating properly. If not, there is a problem with a switch or the system. See your authorized dealer for service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Press the Unlock transmit button on the key fob once to unlock driver’s door, rear liftgate/decklid, fuel filler door, and center console (roadster only). Press the Unlock transmit button twice to unlock both doors, rear liftgate/ decklid, fuel filler door, and center console (roadster only). To Lock The Doors: Press the Lock button on the key fob once. All turn signal lights blink three times to indicate that the vehicle is locked.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Panic Alarm The panic alarm unlocks the driver’s door, turns on the interior lights, flashes the foglights and sounds the horn for about three minutes or until the alarm is turned off. The vehicle can be driven while in the Panic mode. To Use the Panic Alarm: Press and hold the Panic button to activate the alarm. Press and hold the Panic button or unlock the door with the key to deactivate the alarm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Transmitter Battery Service The recommended replacement Lithium battery is Panasonic威 CR 2025 or equivalent. 2 To change the batteries: • Insert the new batteries in the direction of the arrow with the positive symbol facing upwards. • Replace the battery cover and press on it until you feel it engage. • Press release button (2) on the key fob. The key folds out. • Press the battery cover (1) in the direction of the arrow. • Remove the old batteries.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE approximately 30 seconds, insert the key in the ignition and turn it to the ON/RUN position. The remote control should once again be operational. SECURITY ALARM SYSTEM The system monitors the doors, rear liftgate/decklid, hood, and ignition for unauthorized operation. The security alarm system is automatically armed or disarmed with the remote control or any of your vehicle’s keys by locking or unlocking the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The tow-away alarm remains switched off until the vehicle is locked again with the key or the remote control, at which time it is automatically reactivated. 19 DECKLID INTERNAL EMERGENCY RELEASE ROADSTER As a security measure, a Decklid Internal Emergency Release lever is built into the decklid latching mechanism.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! If the battery voltage drops below the minimum threshold at any time, the Trunk Internal Emergency Release will not function. WARNING! The Trunk Internal Emergency Release will not function during the convertible top operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 POWER WINDOWS The power window switches are located in the console. To operate, turn the key in the ignition switch to the ACC or ON/RUN position. Press the switch in to the resistance point to open; release the switch when the window is in the desired position. 2 For express opening of windows, press the switch past the resistance point and release; the window lowers to the fully open position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Window Operation With The Convertible Top Switch (Roadster Only) The power windows can also be operated by using the convertible top switch. To operate, turn the key in the ignition switch to the ON/RUN position. Press down on the rear of the convertible top switch twice to open the windows. Press down on the front of the convertible top switch twice to close the windows.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other occupants, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In cases of other frontal impacts, roll overs, certain side impacts, rear collisions or other accidents without sufficient frontal or rear impact forces, the emergency tensioning retractors will not be activated. The driver and passenger will then be protected by the fastened seat belts and inertia reel in the usual manner. WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 25 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up a little on the shoulder belt, as shown. 5. To loosen the lap belt if it is too tight, tilt the latch plate away from you and pull on the lap belt. Remember that a snug belt reduces the risk of sliding under the belt in a collision. 6.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 WARNING! WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Restraint System (SRS) - Airbag 29 The vehicle is also equipped with side airbags, located in the driver and passenger doors. Side airbags also work with seat belts to improve occupant protection. WARNING! This vehicle has airbags for the driver and passenger as a supplement to the seat belt restraint systems. The driver’s airbag is mounted in the steering wheel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The seat belts are designed to protect you in many types of collisions. The front airbags deploy only in moderate to severe front collisions. In certain types of collisions, both the front and side airbags may be triggered. But even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during airbag deployment could cause serious injury. • Airbags need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Occupant Restraint Controller monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or ON/RUN positions. These include all of the items listed above except the knee bolster, the instrument panel, and the steering wheel and column. • The Occupant Restraint Controller also turns on the AIRBAG light in the instrument panel for four seconds when the ignition is first turned on, then turns the light off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE then quickly deflate while helping to restrain the driver and passenger. The airbag gas is vented through the airbag material towards the instrument panel. In this way the airbags do not interfere with your control of the vehicle. • The knee impact bolster helps protect the knees and working with the seat belts, position you for the best interaction with the airbags. 33 If a Deployment Occurs WARNING! Deployed airbags can’t protect you in another collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • When a side impact above a predetermined threshold occurs, the sensors signal the inflator on the impacted side of the vehicle. A large quantity of nontoxic nitrogen gas is generated to inflate the airbag. The door panel opens to allow the airbag to inflate to its full size. 35 WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The operational readiness of the side airbag system is verified by the airbag indicator light in the instrument cluster when turning the key in the ignition switch to the ON/RUN position. If no fault is detected, the light will go out after approximately four seconds. After the light goes out, the system continues to monitor the components and circuitry of the airbag system and will indicate a malfunction by coming on again.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Passenger Front Airbag On/Off Switch The on/off switch is located at the right end of the instrument panel and is accessible by opening the passenger door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To turn OFF the passenger front airbag, use the on/off switch located on the instrument panel. NOTE: When the passenger airbag is turned off, the yellow airbag off light will illuminate. To Shut Off the Passenger Airbag: • Place the ignition key in the on/off switch, turn the key clockwise, and remove the key from the switch. This will shut off the passenger front airbag. • The air bag will remain off until the switch is turned back to the ON position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Turn On the Passenger Airbag: • Place the ignition key in the on/off switch, turn the key counterclockwise, and remove the key from the switch. This will turn on the passenger airbag. The Passenger Airbag Off light on the console will turn off, or will not be illuminated when the ignition is turned to the ON position. WARNING! The airbag may malfunction and serious injury could result if key is left in the airbag shut off switch. Always remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light You will want to have the airbags ready for your protection in case of a collision. While the airbag Supplemental Restraint System (SRS) is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately. • The AIRBAG light does not come on or flickers during the four seconds when the ignition switch is first turned on. • The light remains on or flickers after the four second interval.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs. (9 kg). “Convertible” child seats can be used either rearward-facing or forward-facing in the vehicle. Convertible child seats often have a higher weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children who weigh more than 20 lbs. (9 kg) but are less than one year old.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may not work when you need it. • Buckle the child into the seat according to the seat manufacturer’s directions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back. LATCH - Child Seat Anchorage System (Lower Anchors and Tether for Children) Your vehicle’s passenger seat is equipped with the child restraint anchorage system called LATCH.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The passenger seat tether anchorage is located on the back of the seat cushion frame. It is visible by moving the passenger seat forward in the vehicle. Many, but not all LATCH-Compatible child restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Installing Child Restraints Using the Vehicle Seat Belt Child restraints can be securely fastened in the passenger seat using the seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To attach the tether strap to the anchor, move the seatback fully forward. Pass the child restraint tether hook over the top of the seat, through the strap near the top of the seat back, and attach it to the anchor bar behind the passenger seat, below the seatback. After securing the tether hook to the bar, recline the seatback fully rearward and move the seat to its most rearward position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS The engine in your new Crossfire does not require a long break-in period. Following these few simple guidelines is all that is necessary for a good break-in. • Drive your vehicle at moderate vehicle and engine speeds during the first 1,000 miles (1,600 km). • Do not make any full throttle starts and avoid full throttle acceleration. • Use the proper transmission gear for your speed range. • Avoid excessive idling.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside the Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.). If there is any question regarding belt or retractor condition, see your authorized dealer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Convertible Top Operation . . . . . . . . . . . . . . . .52 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 ▫ To Lower The Top . . . . . . . . . . . . . . . . . . . . . .53 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .67 ▫ To Raise The Top . . . . . . . . . . . . . . . . . . . . . .58 ▫ Exterior Mirrors Folding Feature . . . . . . . . . . .67 ▫ Convertible Top Lamp And Audible Signal Chart . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Heated Seats (If Equipped) . . . . . . . . . . . . . . .73 ▫ Windshield Wipers And Washer . . . . . . . . . . . .80 䡵 To Open And Close The Hood . . . . . . . . . . . . .74 ▫ Mist Function . . . . . . . . . . . . . . . . . . . . . . . . .81 䡵 Interior Lights . . . . . . . . . . . . . . . . . . . . . . . . .75 䡵 Telescoping Steering Column . . . . . . . . . . . . . .82 ▫ Front Map/Reading Lights . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 51 ▫ Using The Universal Transceiver . . . . . . . . . . 101 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 ▫ Erasing Universal Transceiver Buttons . . . . . . . 101 䡵 Umbrella Hook . . . . . . . . . . . . . . . . . . . . . . . 102 ▫ Reprogramming a Single Button . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONVERTIBLE TOP OPERATION WARNING! The convertible top does not provide the structural protection that a reinforced metal roof does and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision. Therefore, it is important that all occupants wear their seat belts at all times when riding in a convertible.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! When opening and closing the convertible top, make sure that: • There is sufficient clearance of at least 6 ft. (1.8m) for the convertible top to move up. • Nothing is placed on the tonneau cover. • The outside temperature is above 32°F (0°C). Otherwise the convertible top and other parts of the vehicle could be damaged. CAUTION! Use caution when putting items into the storage compartment with the top in the closed position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! To avoid possible damage to the tonneau cover and convertible top, do not allow the convertible top to remain in the suspended position. After approximately 10 minutes in the suspended position, the hydraulic pressure will be released which will allow the top and the tonneau cover to lower. The convertible top switch can be pressed to cancel this operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: See label attached to underside of decklid. 55 CAUTION! Be sure to turn the ignition to the “ON/RUN” position before releasing the top from the windshield header. The windows will not go down if the top is released from the header without the ignition turned “ON”. The side windows can be damaged if the doors are opened or closed with the windows up and the top released from the windshield header. 3. Turn the ignition key to the ON/RUN position. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Once the release handle is rotated, the windows will automatically go down. 5. Push up on the convertible top latch handle to create a gap between the header and top of approximately 8 inches (200 mm). As soon as the top is free, rotate the latch handle counterclockwise just over one quarter turn and push it up into the stored position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Once the top is lowered and the audible signal is heard, you can continue to push the convertible top switch down or push it within 2 seconds to raise the windows. The windows can also be closed/opened later using the power window switches. 57 CAUTION! To prevent mildew, the convertible top must be dry before lowering it into the storage compartment. Do not lower a frozen convertible top until thawed and dry.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Raise The Top: 1. Make sure the rear cargo compartment divider is still secured in the vertical position. 2. Make sure the decklid is closed. 3. Turn the ignition key to the ON/RUN position and press down on the front of the convertible top switch. 4. If the windows are raised, they will lower as soon as the convertible switch is pressed down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 59 6. Pull the latch handle and convertible top down to engage the top with the header. 3 WARNING! 7. When the top engages to the header, turn the latch handle counterclockwise just over one quarter turn to the lock position and push the latch handle up to the stored position. The top is now secured in the closed position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 8. Once the top has been raised and locked, the cargo compartment divider can be unhooked and folded forward to increase the cargo compartment capacity. Follow the steps shown on the label affixed to the decklid trim. CAUTION! Once the cargo compartment divider is folded forward to increase the cargo compartment capacity, the tonneau cover flaps are exposed and can be damaged by long items being put into the cargo compartment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Convertible Top Lamp and Audible Signal Chart Below is a table containing all of the visual and audible signals that can be seen or heard during top operation or if a fault is present.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES The console has a power outlet/cigar lighter, an ash tray with a coin holder, a cupholder (if equipped), and the passenger airbag light. In addition, there are switches to control the heated seats (if equipped), rear spoiler, electronic stability program (ESP), hazard flashers, central locking, rear defroster and towing alarm.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage Compartments There is a storage compartment in the console. To open the storage compartment, lift the lid with the finger depressions on either side. To close, lower the lid until the lock engages. 63 On some models, a cargo net for storage is located in the footwell area on the passenger side. 3 Additionally, storage pockets are located on the wall behind each seat and on each door panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE A storage pouch is located on the rear wall between the seats, and the driver’s sunvisor has a document strap. WARNING! WARNING! Remove the ashtray only with the vehicle stopped and the ignition off. Otherwise, the vehicle might move unexpectedly as a result of unintended contact with the gear selector lever. Keep compartment lids closed. This will help to prevent stored objects from being thrown about and injuring vehicle occupants during an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Coin Holder With the ashtray open, folding down the cover plate reveals the coin holder, which can accommodate nine coins in various sizes up to a U.S. quarter. The coin slots are shaped to retain the coins, and the cover plate ensures that the coins remain in the coin holder. Power Outlet/Cigar Lighter The dual-purpose power outlet is located in the console, next to the passenger airbag off warning light.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Glove Compartment To lock the glove compartment, turn the key to the right and remove. To unlock, turn the key to the left and remove. Pull on the handle to open the glove compartment. CUPHOLDER (If Equipped) The cupholder is located in the console. To open the cupholder, gently press downward on the front edge of the top panel, and then release. The cupholder will open automatically.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustment. 67 Exterior Mirrors Folding Feature All exterior mirrors are hinged to move forward or rearward to resist damage. The hinges have three detent positions: full forward, full rearward, and normal.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Remote Control Outside Mirrors The mirrors can be adjusted by using the remote control located in the console. Rotate the switch to the right to select the right mirror, rotate to the left to select the left mirror. Then use the switch to adjust the selected mirror to the desired direction.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vanity Mirrors 69 SEATS Your vehicle’s seats can be adjusted either manually or electrically, depending on how your vehicle is equipped. WARNING! A vanity mirror is on each sun visor. To use the mirror, rotate the sun visor down and slide open the mirror cover. • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: When moving the seat, be sure that there are no items in the footwell or behind the seats. Otherwise you could damage the seats. Manual Seat Adjustments (If Equipped) Seat Height (Drivers Seat Only) • Pull up on handle 3. • To lower the seat, use your body weight to push the seat downward. • To raise the seat, lift your body weight off the seat to obtain a higher seat position. • Release handle 3 when you are at your desired seat level.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Forward/Rearward • Pull up on handle 4. • Move the seat forward or backward to your desired position which allows you to reach the pedals comfortably. • Let go of handle 4. The seat should make an audible click when positioned properly. • Check for proper engagement before driving. Backrest Tilt • Turn handwheel 2 forward or backward to adjust the backrest tilt to your desired position which allows your arms to slightly bend when holding the steering wheel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver Eight-Way Power Seat (If Equipped) The switches to adjust the power seats are located on the outboard side of each seat. The driver’s seat features eight-way power adjustment - horizontal, vertical, cushion tilt and back angle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 Passenger Four-Way Power Seat (If Equipped) The switches to adjust the passenger seat are also on the outboard side of the seat. The passenger seat provides four-way adjustment - horizontal and back angle. 3 After turning the ignition switch ON, you can choose the HI, LO, or OFF setting. Indicators on the switches show which setting has been selected. Heated Seats (If Equipped) This feature heats the driver and passenger seats.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, pull the release lever located inside your vehicle, below the instrument panel. WARNING! Then, reach under the hood and pull upward on the safety latch and lift the hood. To prevent possible damage, close the hood by dropping it from approximately 12 inches (30 cm). If the hood is not fully latched, it could fly up when the vehicle is moving, and block your forward vision. You could have a collision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE INTERIOR LIGHTS A two-position mode selector switch controls the interior lights located in the overhead console. 75 Front Map/Reading Lights These lights are located between the sun visors. A single centrally located switch operates both lights. 3 The AUTO mode turns the lights on when a door is open or ajar, or when locking or unlocking the vehicle. AUTO mode also has a “fade to off” feature. When the doors are closed or locked, they gradually “fade” off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Instrument Panel Lighting With the parking lights or headlights on, rotate the dimmer control to the left of the speedometer to increase or decrease brightness of the instrument panel. Night Security Illumination For added security when exiting the vehicle after driving with the exterior lights on, the lights will switch on again for approximately 30 seconds after closing the last door. The lights-on timing can be changed at your authorized dealer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lights-On Reminder If the headlights or parking lights are left on after the ignition is turned off, a warning will sound if the driver’s door is opened. Daytime Running Lights (Where Applicable) VEHICLES WITH AUTOMATIC TRANSMISSION The low beam headlights, parking lights, side marker lights, taillights and license plate lights are automatically switched on whenever the vehicle is started and the transmission gear selector is in a driving position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! MULTIFUNCTION CONTROL LEVER Standing lamps are intended for short term use when parking. If these lights are left on for a long period of time, your car’s battery may drain, causing a possible starting problem. Assure that the headlamp switch is in the OFF position when leaving the vehicle. Turn Signals Move the multifunction control lever up to activate the right turn signal; move the lever down to activate the left turn signal.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To operate the turn signals continuously, move the control lever up or down past the point of resistance. The operation is automatically canceled when the steering wheel is turned to a large enough degree. If one of the turn signal lights fail, the turn signal indicator system flashes and sounds at a faster than normal rate. If an indicator fails to light when the control lever is moved, it may mean that the fuse or indicator bulb is defective.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Passing Light You can signal another vehicle with your headlights by lightly pulling the multifunction control lever toward the steering wheel. This will cause the headlights to turn on at high beam and remain on until the control lever is released. Windshield Wipers And Washer The wipers and washer are operated by a switch in the multifunction control lever. Turn the end of the lever to select desired wiper speed: off, intermittent, normal, or fast.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Push the end of the lever inward and hold it to activate the wiper and washer together. 3 WARNING! Mist Function Push the end of the multifunction control lever inward briefly for a single wipe without adding washer fluid. Use this feature only when the windshield is wet. Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TELESCOPING STEERING COLUMN Unlock the steering column by pulling out the handle located directly below the column. The indicator light located in the instrument cluster will come on. To lengthen or shorten the steering column, pull out or push in the steering wheel. Lock the steering column in position by pushing the handle in until it engages. The indicator light in the instrument cluster will go out. WARNING! Do not adjust the steering wheel while driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If the indicator light in the instrument cluster does not go out after starting the engine, the telescoping column is not locked properly. Do not drive the vehicle until you have properly locked the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. The Tire Pressure Monitor (TPM) system uses wireless technology to monitor tire pressure levels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 The TPM system will cause the indicator lamp in the instrument cluster to illuminate whenever the pressure in one tire falls 25% below the recommended pressure shown on the vehicle’s tire label. NOTE: The pressure in your tires changes with temperature. A significant decrease in temperature could reduce cold inflation pressure below the TPM setpoint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! The TPM system has been optimized for the original equipment tires and wheels. TPM system pressures have been established for the tire size equipped on your vehicle. Undesirable operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use aftermarket tire sealant or balance beads, as damage to the sensors may result.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 REAR SPOILER CAUTION! Do not push or pull on the spoiler when deployed. Damage to the spoiler could result. A rear spoiler enhances vehicle stability. The rear spoiler deploys automatically when vehicle speed reaches approximately 62 mph (100 km/h). The spoiler begins to retract at 39 mph (62 km/h). When retracted, the spoiler fits between the quarter panels, and aft of the liftgate window or tonneau cover.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The spoiler control also incorporates an emergency stop feature. If, for any reason, spoiler motion needs to be stopped, pressing either the top or bottom of the switch will stop the spoiler motion. Once the deployment speed is reached, however, the spoiler deploys to its full up position. The spoiler will deploy as a safety precaution if the ESP system detects a large difference in wheel speed between the front and rear wheels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not drive the vehicle at speeds above 62 mph (100 km/h) if the red spoiler warning indicator is illuminated. You could have reduced vehicle stability and control. WARNING! Keep hands and fingers away from the spoiler and spoiler linkage when the spoiler is deploying or retracting. The linkage could pinch your fingers and cause serious injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The BAS is designed to maximize the vehicle’s braking capability during emergency braking maneuvers. The system applies maximum power boost to the brakes more quickly in emergency braking conditions than might otherwise be afforded solely by the driver’s braking style. This can help reduce braking distances. The BAS complements the antilock brake system (ABS). Applying the brakes very quickly results in maximum BAS assistance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the malfunction indicator light stays illuminated, have the BAS and ESP checked at your authorized dealer as soon as possible. ELECTRONIC STABILITY PROGRAM (ESP) WARNING! ESP cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded. The ESP cannot prevent accidents, including those resulting from excessive speed in turns, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, switch off the ESP system by pressing the upper half of the ESP switch. With the ESP system switched off, the engine torque reduction feature is cancelled. Therefore, the enhanced vehicle stability offered by ESP is unavailable. ESP always operates under braking, even with the switch in the OFF position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! If the vehicle is towed with the front axle raised, the engine must be shut off (key in the ignition switch to the OFF/LOCK or ACC position). Otherwise the ESP will immediately be engaged and will apply the rear wheel brakes. Synchronizing ESP If the power supply was interrupted (battery disconnected or discharged), the BAS/ESP malfunction indicator light may be illuminated with the engine running.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL The electronic speed control automatically maintains the set speed by actively regulating the throttle setting. Any speed above approximately 20 mph (30 km/h) can be maintained with the electronic speed control by operating the lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To accelerate and set a speed, lift the lever up. Lift and hold the lever to accelerate, or lift and release to set a speed. To decelerate and set a speed, press the lever down. Press down and hold the lever to decelerate, or press down and release to set a speed. 95 WARNING! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate A soft tap on the brake pedal, or normal brake pressure while slowing the vehicle, will deactivate the speed control without erasing the memory. Pushing the speed control lever forward or turning the key in the ignition switch to the OFF/LOCK position will turn off the speed control and erase the memory. To Resume Speed To resume a previously set speed, pull the speed control lever toward you, and then release.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using Speed Control On Hills Your vehicle is equipped with interactive speed control. This feature activates when driving up or down hills with the speed control engaged and the driver’s foot off the accelerator. WARNING! Speed control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature, as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features, as it could cause injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Step 3 does not have to be followed to program additional hand-held transmitters. 4. Choose one of the three buttons to program. Place the hand-held controller 1–3 inches (25–76 mm) from the universal transceiver while keeping its indicator light in view. 99 NOTE: Some gate operators and garage door openers may require you to replace this Programming Step 5 with procedures noted in the “Gate Operator/Canadian Programming” section. 6.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Programming Steps 8-10 to complete programming of a rolling code equipped device (most commonly a garage door opener). 8. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 9.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Continue to press and hold the universal transceiver button while you press and release every two seconds (“cycle”) your hand-held transmitter until the frequency signal has successfully been accepted by the universal transmitter. (The indicator light will flash slowly and then rapidly.) Proceed with Programming Step 6 to complete. Using the Universal Transceiver To operate the universal transceiver, simply press and release the programmed button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received, including interference that may cause undesired operation. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instruments And Controls . . . . . . . . . . . . . . . . 104 ▫ Driver – L/R . . . . . . . . . . . . . . . . . . . . . . . . 126 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . 105 ▫ Telephone Mute Characteristics . . . . . . . . . . . 126 䡵 Instrument Cluster Description . . . . . . . . . . . . 107 䡵 Compact Disc Maintenance . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENTS AND CONTROLS
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER The instrument cluster displays are activated by either opening the door, pressing the left button within the 105 cluster, or turning the key in the ignition switch to the ON/RUN position.
UNDERSTANDING YOUR INSTRUMENT PANEL
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Low Windshield Washer System Fluid Level Warning Light With the key in the ignition switch turned to the ON/RUN position, the indicator light comes on. It should go out when the engine is running. If the indicator light does not go out after starting the engine, or if it comes on while driving, the fluid reservoir is less than 1⁄4 filled.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The TPMS is designed to monitor your tire pressure and will not function as a tire pressure gauge. After adjusting the air pressure in a tire, there will be a delay before the system updated the display NOTE: The TPMS can inform you about a low tire pressure condition, but it does not replace normal tire maintenance. The TPMS is not intended to provide you with notification of a rapid pressure loss. NOTE: The pressure in your tires changes with temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL 109 CAUTION! The arrows in the instrument cluster will flash in unison with the respective exterior turn signal. Continuing to drive with an overheated engine cooling system can cause damage to the engine or other components. 7. Electronic Stability Program (ESP) Indicator Light The yellow ESP indicator light in the speedometer dial comes on with the key in the ignition switch turned to the ON/RUN position. It should go out with the engine running. 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 10. Brake System Warning Light The dual brake system provides a reserve braking capability if a failure occurs in a portion of the hydraulic system. This light monitors both the brake fluid level and the parking brake. If the light comes on, it indicates either that the parking brake is on or there is a low fluid level in the brake master cylinder.
UNDERSTANDING YOUR INSTRUMENT PANEL The indicator light will come on when the exterior light fails. If a brake light fails, the light outage indicator will come on when applying the brake and stays on until the engine is turned off. NOTE: If additional lighting equipment is installed (e.g., auxiliary headlights, etc.) be certain to connect into the fuse before the failure indicator monitoring unit in order to avoid damaging the system. 12.
UNDERSTANDING YOUR INSTRUMENT PANEL The seat belt indicator light will remain lit until the seat belts are fastened. CAUTION! 15. Charging System Indicator Light Should the charging system indicator light fail to come on prior to starting when the key is in the ignition switch in the ON/RUN position, or should it fail to go out after starting or during operation, it indicates a malfunction that must be repaired immediately at an authorized dealer.
UNDERSTANDING YOUR INSTRUMENT PANEL 113 The display can be adjusted with the knob/button located to the left of the clock. • Press the button twice (with the key removed or in the OFF/LOCK or ACC position). 18. Gear Indicator For automatic transmission vehicles, the current gear shift selector range is indicated in the gear range indicator display. 21. Main Odometer, Flexible Service System (FSS) This shows the total distance the vehicle has been driven. 19.
UNDERSTANDING YOUR INSTRUMENT PANEL To reset the trip odometer, press the knob/button once with the key in the ON/RUN position. Press the knob/ button twice with the key removed or in the OFF/LOCK or ACC position. The FSS permits a flexible service schedule that is directly related to the operating conditions of the vehicle. There are two symbols which will appear in the main odometer display field prior to the next suggested service. This symbol represents Service A.
UNDERSTANDING YOUR INSTRUMENT PANEL 115 or while driving when reaching the service warning threshold. It can be canceled manually by pressing the knob/button. starts combined with short distance driving in which the engine does not reach normal operating temperature, reduce the interval between services.
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! The outside temperature indicator is not designed to serve as an ice-warning device and is unsuitable for that purpose. Indicated temperatures just above the freezing point do not guarantee that the road surface is free of ice. 24. Airbag Light The operational readiness of the airbag system is verified by the airbag indicator light in the instrument cluster when turning the key in the ignition switch to the ACC or ON/RUN position.
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! Do not drive the vehicle until you have properly locked the steering column. 117 If the vehicle is not driving normally, and the Check Engine light flashes or remains on continuously, it is an alert to serious conditions that could lead to loss of power or severe catalytic converter damage. The vehicle should be serviced at an authorized dealer as soon as possible. 26.
UNDERSTANDING YOUR INSTRUMENT PANEL CHECKING ENGINE OIL LEVEL A sensor in the oil pan allows oil level to be checked without opening the hood. It provides an accurate measurement of oil level, whereas the low engine oil level indicator warns that oil level is definitely too low. With the vehicle parked on a level surface, the engine is warmed up and shut off for approximately five minutes.
UNDERSTANDING YOUR INSTRUMENT PANEL 119 “INFINITY MODULUS” AM/FM STEREO RADIO WITH SINGLE-DISC CD PLAYER AND GPS NAVIGATION (OPTIONAL - See separate User’s Manual) AM/FM STEREO RADIO WITH SINGLE-DISC CD PLAYER 4 INFINITY MODULUS Entertainment Systems A premium Infinity Modulus AM/FM stereo, single-disc CD audio system is standard equipment on some models. It feeds a six-channel, 240-watt amplifier with dual subwoofers mounted in the back panel behind the seats, and four door-mounted speakers.
UNDERSTANDING YOUR INSTRUMENT PANEL The volume is controlled by rotating the ON/OFF knob to the left or right. Audio (AUD) Settings • Bass (BASS) Press the AUD button repeatedly until BASS appears. Rotate the right rotary control for the desired level (from -9 to +9). • Treble (TREB) Press the AUD button repeatedly until TREB appears. Rotate the right rotary control for the desired level (from -9 to +9). • Balance (BAL) Press the AUD button repeatedly until BAL appears.
UNDERSTANDING YOUR INSTRUMENT PANEL 121 FM AS – An autostore feature will store the 9 current stations with the strongest signal on station buttons 1-9 in the order of their signal quality. Storing FM stations – 10 frequencies can be stored on FM 1 and on FM 2 by pressing a multifunction button for three seconds; a tone will confirm that the selection was set. Press the FM button repeatedly until FM AS is displayed to perform an autostore scan.
UNDERSTANDING YOUR INSTRUMENT PANEL Press the button again to keep the received program. If the selected station does not transmit a PTY identification, the display will show NO PTY. If all criteria for evaluating RDS are not met, the unit will only display the frequency.
UNDERSTANDING YOUR INSTRUMENT PANEL AM-AM AS The system has two AM modes available. Press the AM button repeatedly until the band or operation mode is selected. To search in this mode, press the right rotary control/push button and the abbreviation SC is displayed. Receivable stations can be heard for eight seconds. Press the control again to keep the received station. Once the scan search begins, it will continue until either a station is retained or until another mode is selected.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Before inserting a CD, assure that a CD is not already in the player. Press the CD button; if the display shows NO CDS, a new CD can be inserted. If a CD is already loaded, press and release the EJT button and allow time for the current CD to be ejected. Loading a new CD into the player while another CD is already loaded can result in a jammed mechanism which may require service at an authorized dealer. Insert the CD into the slot with the printed side up.
UNDERSTANDING YOUR INSTRUMENT PANEL • Relative Time Display (T) Press the multifunction button T for the time of the currently playing track to be displayed for approximately eight seconds. • Random Play (RP) Press the multifunction button RP for random generation of the next track to be played. Press the button again to cancel the feature. NOTE: To protect the unit from excessive heat, a temperature protection device has been integrated into the circuitry.
UNDERSTANDING YOUR INSTRUMENT PANEL Mono/Stereo In order to suppress reception-related interference, three different parameters can be set to optimize reception. To activate, call up the user menu, then press the right rotary control/push button repeatedly until STEREO, STO AUTO or MONO is displayed (depending on the currently selected setting, you may need to turn the knob also for your selection). • STO AUTO – Setting for normal operation.
UNDERSTANDING YOUR INSTRUMENT PANEL Call up the user menu, then press the right rotary control/push button repeatedly until AUDIO PH or PH MUTE is displayed (depending on the currently selected setting, you may need to turn the knob also for your selection). COMPACT DISC MAINTENANCE To keep the compact discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL The settings and controls are as follows: Temperature Control Use the driver or passenger temperature control to regulate the temperature of the air inside the passenger compartment. The blue area of the control indicates cooler temperatures, while the red area indicates warmer temperatures. The temperature selector should be left at the desired temperature setting so that the system can automatically reach that selection as quickly as possible.
UNDERSTANDING YOUR INSTRUMENT PANEL Basic Setting - Air Conditioner Press the air conditioning ON/OFF switch. The light in the switch will illuminate. Select a temperature for each side of the passenger compartment. Select the air volume with the fan control switch, at least to position 1. Set the air distribution control switch to one of the positions shown above. Open center air outlets. Open left and right side air outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL control switch to position 1 or higher. Close the center, left, and right side air outlets. Turn the defroster outlets for the side windows to the detent position. NOTE: The air conditioner removes moisture from the air inside your vehicle. The quickest and most efficient method for defogging your windows, even if the air temperature in your vehicle is cool, is to use the air conditioner. Make sure that you press the A/C button to defog your windows.
UNDERSTANDING YOUR INSTRUMENT PANEL Climate Control - OFF To switch the climate control off, set the air volume control switch to position 0. The fresh air supply to the vehicle interior is shut off. While driving, use this setting only temporarily, otherwise the windshield could fog up. inside the switch starts blinking. As soon as the battery has sufficient voltage, the defroster automatically turns itself back on.
UNDERSTANDING YOUR INSTRUMENT PANEL after approximately 30 minutes, at outside temperatures above approximately 40°F (5°C); after approximately five minutes, if the A/C button is pressed. At high outside temperatures, the system automatically engages the recirculated air mode for approximately 30 minutes, thereby increasing the cooling capacity performance. Press the recirculation button again to extend the recirculated air mode.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 137 ▫ Park Position . . . . . . . . . . . . . . . . . . . . . . . . 143 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 137 ▫ Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 ▫ Extremely Cold Weather (Below -20°F Or -29°C) . 138 ▫ Neutral . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . . 138 ▫ Drive . . .
STARTING AND OPERATING ▫ Electronic Stability Program (ESP) . . . . . . . . . 152 ▫ General Information . . . . . . . . . . . . . . . . . . . 167 ▫ Synchronizing ESP . . . . . . . . . . . . . . . . . . . . 153 䡵 Tire Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 ▫ ESP Control Switch . . . . . . . . . . . . . . . . . . . . 154 䡵 Original Equipment Tires . . . . . . . . . . . . . . . . 168 ▫ Anti-Lock Brake System (ABS) . . . . . . . . . . . . 155 䡵 Snow Tires . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES WARNING! Do not leave animals or children inside parked vehicles in hot weather; interior heat build up may cause serious injury or death. Be sure that the parking brake is engaged and that selector lever is in the NEUTRAL or PARK position (gearshift lever in Neutral). Turn the key in the ignition switch to the ON/RUN position. Apply the brakes before shifting into any driving gear.
STARTING AND OPERATING NOTE: Due to the starter non-repeat feature, the key must be turned completely to the left before attempting to start the engine again. If Engine Fails to Start CAUTION! Do not try to push or tow your vehicle to get it started. Your vehicle cannot be started this way. Pushing with another vehicle may damage the transmission or the rear of your vehicle. See Section 6 of this manual for proper jump-starting procedures.
STARTING AND OPERATING If the engine fails to start after you have followed the Normal Starting procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine. This should clear any excess fuel in case the engine is flooded. 139 After Starting The idle speed will automatically decrease as the engine warms up.
STARTING AND OPERATING Fully depress the clutch pedal before you shift gears. As you release the clutch pedal, lightly depress the accelerator pedal. NOTE: During cold weather, until the transmission lubricant has warmed, you may have difficulty shifting. This is normal and not harmful to the transmission. Be sure the transmission is in FIRST gear, (not THIRD), when starting from a stopped position. Damage to the clutch can result from starting in THIRD.
STARTING AND OPERATING 141 WARNING! CAUTION! When leaving the vehicle, always remove the key from the ignition switch, and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Children could move the gearshift lever, which could result in an accident or serious injury. If you skip more than one gear while downshifting or downshift at too high an engine speed, you could damage the engine, transmission, or clutch.
STARTING AND OPERATING • Program mode selector switch • Accelerator position • Vehicle speed The gear shifting process is continuously adapted, dependent on the driving style, the driving situation and the road characteristics. The selector lever is automatically locked while in the PARK position. To move the selector lever out of the PARK position, the brake pedal must be firmly depressed before the shift lock will release.
STARTING AND OPERATING Maneuvering To maneuver in tight areas, control the vehicle speed by gradually releasing the brakes. Accelerate gently and never abruptly step on the accelerator. To rock a vehicle out of soft ground (mud or snow), alternately shift from forward to reverse, while applying only slight acceleration. Rocking a vehicle free in this manner may cause the ABS or traction system malfunction indicator light to come on.
STARTING AND OPERATING With a malfunction in the vehicle’s electrical system, the selector lever could remain locked in the PARK position. To unlock the selector lever manually, insert the end of the multipurpose tool from the glove box (or ball point pen) into the covered opening below the position “D” of the shift pattern. While pushing the tool down, move the selector lever out of the PARK position. After removal of the tool from the opening, the cover will not close fully.
STARTING AND OPERATING Drive The transmission automatically upshifts through fifth gear. The DRIVE position provides optimum driving characteristics under all normal operating conditions. AutoStick姞 Gear selection The transmission gear can be selected by pressing the selector lever to the right or the left with the selector lever in the DRIVE position. The gear currently selected is indicated in the instrument cluster display. Briefly press selector lever in the “D-” direction.
STARTING AND OPERATING The delayed upshift is effective with vehicle speeds below 31 mph (50 km/h) at partial throttle and engine temperatures below 95°F (35°C). To prevent the engine from laboring at low RPM when driving uphill or with your vehicle heavily loaded, the automatic transmission will downshift when necessary to maintain engine RPM within the best torque range. Gear Ranges “P” PARK NOTE: If the key is in the ON/RUN position, you must press the brake pedal to shift out of the PARK position.
STARTING AND OPERATING Program mode selector switch The transmission is provided with a selector switch for Standard “S” and Winter/Wet “W” (snow and ice) program modes. 147 down into a lower gear. Rapid release of the accelerator pedal will normally result in an upshift. This gear shifting process is dependent on the current vehicle speed. For Winter/Wet (snow and ice) mode, press the “W” symbol on the switch.
STARTING AND OPERATING Emergency Operation (Limp Home Mode) If vehicle acceleration worsens, or the transmission no longer shifts, the transmission is most likely operating in Limp Home Mode which engages when there is a malfunction of the transmission. This condition may be accompanied by the CHECK ENGINE light in the instrument cluster coming on. In this mode only the SECOND gear or REVERSE gear can be activated. To engage SECOND gear or REVERSE: 1. Stop the vehicle. 2.
STARTING AND OPERATING 149 precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied when the driver is not in the vehicle. WARNING! Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and an accident. To release the parking brake, slightly pull up the handle while pushing the lock button, and guide the lever downward to its stop.
STARTING AND OPERATING BRAKE SYSTEM Your vehicle is equipped with power brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be much greater than that required with the power system operating.
STARTING AND OPERATING Once the brake pedal is released, the BAS is deactivated. The malfunction indicator light for the BAS is combined with the Electronic Stability Program (ESP) malfunction indicator light. 151 The BAS/ESP malfunction indicator light in the instrument cluster comes on with the key in the ignition switch turned to the ON/RUN position and should go out with the engine running.
STARTING AND OPERATING Electronic Stability Program (ESP) The ESP enhances directional control and reduces wheelspin under various driving conditions. When ESP is active, engine torque is limited and the ESP warning light starts to flash. WARNING! ESP cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded. The ESP cannot prevent accidents, including those resulting from excessive speed in turns, or hydroplaning.
STARTING AND OPERATING CAUTION! If the vehicle is towed with the front axle raised (see the What To Do In Emergencies section in this manual), the engine must be shut off (key in the ignition switch turned to the OFF/LOCK or ACC position). Otherwise, the ESP will immediately be engaged and will apply the rear wheel brakes. NOTE: When the ESP warning light is illuminated continuously, the ESP is switched off. Adapt your speed and driving to the prevailing road conditions.
STARTING AND OPERATING ESP Control switch The ESP control switch is located in the center console. When the ESP is switched off, the warning light in the instrument cluster comes on. When the ESP is switched on, the warning light goes out. illuminated. With the ESP system switched off, the engine torque reduction feature is cancelled. Therefore, the enhanced vehicle stability offered by ESP is unavailable.
STARTING AND OPERATING Anti-Lock Brake System (ABS) The ABS gives increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up. The system operates to prevent wheel lock-up and help avoid skidding on slippery surfaces. NOTE: The ABS improves steering control of the vehicle during hard braking maneuvers.
STARTING AND OPERATING apparent on ice and snow. The anti-lock brake system pump motor makes a low humming noise during operation, which is normal. briefly during this procedure, or remains on after the engine is running, have the system checked by an authorized dealer. WARNING! Pumping of the brake pedal will diminish the effectiveness of the anti-lock brakes and may lead to an accident. Pumping makes the stopping distance longer.
STARTING AND OPERATING below 10 volts, the malfunction indicator light comes on and the ABS is switched off. When the voltage is above this value again, the malfunction indicator light should go out and the ABS is operational. If the malfunction indicator light stays illuminated, have the system checked at your authorized dealer as soon as possible.
STARTING AND OPERATING Brake Pad Break-In The brakes on your vehicle do not require a long break-in period, but avoid repeated hard brake applications from high speeds during initial break-in. Also avoid severe brake loading such as may be encountered when descending long mountain grades. POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces.
STARTING AND OPERATING TIRE SAFETY INFORMATION See general tire safety information included in the “If You Need Consumer Assistance” section of this manual. TIRES—GENERAL INFORMATION Please take time to read the tire warranty booklet in your Owner’s Manual package. It contains valuable information on tire maintenance. Specific recommendations on guidelines for long—term tire storage should be requested of the tire manufacturer. Please refer to the tire warranty booklet for contact information.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3. Ride Comfort and Vehicle Stability— Proper tire inflation contributes to a comfortable ride. Overinflation produces a jarring and uncomfortable ride.
STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1 km) after a 3 hour period.
STARTING AND OPERATING WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Radial-Ply Tires Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point.
STARTING AND OPERATING Recommended Tire Inflation Pressures Sport Performance (Y speed rating) tires and All-Season Performance (W speed rating) tires Front 225/40 ZR18 . . . . . . . . . . . . . . . 32 psi (221 kPa) Rear 255/35 ZR19. . . . . . . . . . . . . . . . 33 psi (227 kPa) Sport Performance (Y speed rating) tires and All-Season Performance (W speed rating) tires above 100 mph (161 km/h) Front 225/40 ZR18 . . . . . . . . . . . . . . . 36 psi (248 kPa) Rear 255/35 ZR19. . . . . . . . . . . . . .
STARTING AND OPERATING CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. Check with your authorized dealer before replacing tires with a different size. Alignment And Balance The suspension components of your vehicle should be inspected and aligned when needed to obtain full tire tread mileage Poor suspension alignment may result in: • Fast tire wear. • Uneven tire wear, such as feathering and one-sided wear.
STARTING AND OPERATING cannot be expected to function as a tire pressure gauge. There can be a delay between the instant you adjust the air pressure in a tire and when the system updates the display. The TPMS is not intended to provide you with notification of rapid air loss. The TPMS will cause the Telltale lamp in the instrument cluster to illuminate whenever the pressure in one tire falls 25% below the recommended pressure shown on the tire label.
STARTING AND OPERATING the temperature is very cold. ALWAYS check the pressure in your tires if the TPMS Telltale lamp is illuminated. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
STARTING AND OPERATING ORIGINAL EQUIPMENT TIRES Your vehicle is equipped with either sport performance tires or all-season performance tires. The sport performance tires offer the maximum road handling capability in dry and wet weather conditions. The all-season performance tires, while offering slightly less road handling capability, are able to provide traction capability in snow and ice conditions. Both types of tires are rated for high speed operation.
STARTING AND OPERATING If you need snow tires, the recommended size for the front and rear tires is the same size as the original equipment front tires. This size tire on the rear allows the use of tire chains on the rear wheels. Selection of this size tire also requires the purchase of two additional wheels with the same size specification as the original equipment front wheels. Snow tires may have a lower speed rating than factory equipped tires and may not match the maximum vehicle speed.
STARTING AND OPERATING Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed.
STARTING AND OPERATING FUEL REQUIREMENTS Your engine is designed to meet all emissions regulations and provide satisfactory fuel economy and optimum performance when using high quality unleaded gasoline having an octane rating of 91 or higher. DaimlerChrysler Corporation requires the use of 91 octane or higher premium fuel to minimize the potential for engine damage. Light spark knock at low engine speeds is not harmful to your engine.
STARTING AND OPERATING CAUTION! DO NOT use gasolines containing Methanol. Use of these blends may result in starting and drivability problems and may damage critical fuel system components. Problems that result from using methanol/gasoline blends are not the responsibility of DaimlerChrysler Corporation and may not be covered by the Limited Warranty. While MTBE is an oxygenate made from Methanol, it does not have the negative effects of Methanol.
STARTING AND OPERATING states adopting California emission standards, your vehicle will operate satisfactorily on fuels meeting Federal specifications, but emission control system performance may be adversely affected. 173 ADDING FUEL Gasoline sold outside of California is permitted to have higher sulfur levels, which may affect the performance of the vehicle’s catalytic converter. This may cause the CHECK ENGINE light to illuminate.
STARTING AND OPERATING NOTE: The fuel tank filler tube has a restricting door about 2 inches (50 mm) down from the opening. If fuel is poured from a portable container, the container should have a flexible nozzle long enough to force open the restricting door. CAUTION! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. With the key in the ignition switch turned to the ON/ RUN position, the fuel reserve warning light comes on.
STARTING AND OPERATING VEHICLE LOADING The load carrying capacity of your vehicle is in the following chart and on the tire pressure label attached to the driver door pillar. Vehicle Loading Capacities Front Seat Occupants . . . . . . . . . . . . . . . . . . . . . . . 2 Cargo Capacity (with two persons) . . . . 115 lbs (52 kg) Rated Vehicle Capacity . . . . . . . . . . . .
STARTING AND OPERATING CAUTION! WARNING! • To prevent damage to the roof of your vehicle, DO NOT carry any loads on the roof luggage rack which may come in contact with the roof panel. The load should be secured and placed on top of the rack, not directly on the roof. If it is necessary to place some part of the load on the roof, place a blanket or some other protection between the load and the roof surface.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 178 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 178 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 190 䡵 TIREFIT Tire Repair And Jacking . . . . . . . . . . 180 䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . 191 ▫ TIREFIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 ▫ Towing Eyes . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is located in the console. Push in the flasher switch and all front and rear directional signals will flash. Press the flasher switch a second time to turn the flashers off. NOTE: With extended use, the flasher may run down your battery. IF YOUR ENGINE OVERHEATS During severe operating conditions and stop-and-go city traffic, the coolant temperature may rise close to the red area on the gauge.
WHAT TO DO IN EMERGENCIES NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the cooling system and turning off the A/C removes this heat. You can also turn the temperature control to maximum heat, the mode control to floor, and the fan control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the cooling system.
WHAT TO DO IN EMERGENCIES TIREFIT TIRE REPAIR AND JACKING 1. TIREFIT sealant bottle TIREFIT Small punctures, particularly those in the tread, can be sealed with TIREFIT. Foreign objects (e.g., screws or nails) should not be removed from the tire. TIREFIT can be used in outside temperatures down to approximately -4°F (-20°C). 2. Air pump flap 3. Recess in air pump 4. Power plug and cable 5. Air pump hose with pressure gauge 6.
WHAT TO DO IN EMERGENCIES WARNING! Cuts or punctures larger than approximately 0.16 in. (4 mm), tire damage caused by driving with extremely low tire pressure or on a flat tire, or a damaged wheel can pose a hazard while driving. TIREFIT should not be used in such circumstances. Do not drive the vehicle under such circumstances. Contact your nearest authorized dealer for assistance. Take care not to allow the contents of TIREFIT to come in contact with hair, eyes or clothing.
WHAT TO DO IN EMERGENCIES 11. Turn the ignition key to the ON/RUN position. 12. Press the switch on the air pump to 1. The air pump should start to inflate the tire. 13. After five minutes, the tire should be inflated to at least 26 psi (180 kPa) on the pressure gauge. 14.
WHAT TO DO IN EMERGENCIES Preparations for Jacking WARNING! 183 replaced. (See TIREFIT Tire Repair section for a description of cuts and punctures that may be repairable with TIREFIT.) Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
WHAT TO DO IN EMERGENCIES • Block the wheel diagonally opposite the flat tire. • Passengers must not remain in the vehicle when the vehicle is jacked. NOTE: The jack is designed exclusively for jacking up the vehicle at the specified jack location points built beneath either side of the vehicle. Jack Location and Instructions 1. Remove the jack and jack handle from stowage beneath the cargo compartment carpet.
WHAT TO DO IN EMERGENCIES 185 2. The lifting points for the jack are located beneath the outer edge of the body side, directly behind the front wheel housings, and in front of the rear wheel housings.
WHAT TO DO IN EMERGENCIES NOTE: Do not raise the vehicle until you are sure the jack is securely engaged, as shown. 4. Replace the tire. 5. Lower the vehicle by cranking the handle counterclockwise, then remove the jack assembly. NOTE: Before storing the jack, it should be fully collapsed. 6. Ensure proper tire pressure. WARNING! 3. Holding the jack, insert the cradle under the lifting points. Crank the handle clockwise until the jack base meets the ground. Place the jack on firm ground.
WHAT TO DO IN EMERGENCIES 187 WARNING! CAUTION! A loose jack or tool thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and tools in the places provided. Do not try to push or tow your vehicle to get it started. Your vehicle cannot be started this way. Pushing with another vehicle may damage the transmission or the rear of your vehicle.
WHAT TO DO IN EMERGENCIES WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush contaminated area immediately with large quantities of water. A battery generates hydrogen gas that is flammable and explosive. Keep flame or spark away from the vent holes.
WHAT TO DO IN EMERGENCIES 3. Turn off the heater, radio and all unnecessary electrical loads. 189 6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fans. NOTE: If engine does not run after several unsuccessful starting attempts, have it checked at the nearest authorized dealer.
WHAT TO DO IN EMERGENCIES Traction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observed: 1. Slow down during rainstorms or when roads are slushy. 2. Slow down if the road has standing water or puddles. 3.
WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE We recommend that the vehicle be transported using flat bed equipment. This method is preferable to other types of towing. CAUTION! Important! If towing the vehicle, please note the following: With the automatic central locking activated and the key in the ignition switch turned to the ON/RUN position, the vehicle doors lock if the left front wheel and the right rear wheel are turning at vehicle speeds of approximately 9 mph (15 km/h) or more.
WHAT TO DO IN EMERGENCIES CAUTION! • Do not attempt to tow this vehicle from the front with sling-type towing equipment. Damage to the front fascia will result. • Always use wheel lift equipment when towing from the front. The only other approved method of towing is with a flatbed truck. • Do not tow the vehicle from the rear. Damage to the rear sheet metal and fascia will occur. • Do not push or tow this vehicle with another vehicle as damage to the bumper fascia and transmission may result.
WHAT TO DO IN EMERGENCIES 193 Insert the tool (or similar sized screwdriver) into the slot in the grille as shown (the tool must be inserted far enough to engage the clip on the left side of the grille). Push the tool to the left to disengage the clip and detach the grille. The front towing eye is now accessible.
WHAT TO DO IN EMERGENCIES Tow-Away Alarm Once the alarm system has been armed, the exterior vehicle lights will flash and an alarm will sound when anyone attempts to raise the vehicle for towing. The alarm will last approximately three minutes in the form of flashing exterior lights. At the same time, an alarm will sound for 30 seconds. The alarm will stay on even if the vehicle is immediately lowered.
WHAT TO DO IN EMERGENCIES 195 CONVERTIBLE TOP EMERGENCY OPERATION If the convertible top cannot be closed using the convertible top switch, check the following: • Is the decklid closed properly? • Is there sufficient battery voltage? Start the engine if necessary. • Is the rear cargo compartment divider secured in the vertical position? If the power convertible top operation does not function properly, you can close the convertible top manually.
WHAT TO DO IN EMERGENCIES Relieving Hydraulic Pressure NOTE: The hydraulic pressure must be relieved before the top can manually be raised or lowered. 1. Turn the ignition to the “ON” position. 2. Push down on the convertible top switch and hold in that position. 3. Turn the ignition “OFF” and continue to push down on the switch for 5 seconds. 4. After 5 seconds the hydraulic system pressure will be relieved.
WHAT TO DO IN EMERGENCIES 3. Unlock the storage compartment by placing the tool on the bolt between the backrest and the tonneau cover. Turn the wrench in the direction of the arrow to its stop and remove the tool. 197 5. Pull up hard on the upper section of the convertible top to move it out of its storage compartment. 6 NOTE: Do not let go of the convertible top as it may fall back into the convertible top storage compartment. 4. Open the tonneau cover and secure it in the upright position.
WHAT TO DO IN EMERGENCIES 6. Move the convertible top toward the windshield header. 8. Place the rear window section of the convertible top in its vertical position. 9. Close the tonneau cover by placing hands near the edges (arrows) and slowly lowering it. The tonneau cover must lock in the first notch of the compartment cover catch. WARNING! Do not place your hands in the convertible top frame areas. Serious personal injury may occur. 7.
WHAT TO DO IN EMERGENCIES 10. Lock the convertible top storage compartment by placing the tool on the bolt between the backrest and the tonneau cover. Turn the wrench in the direction of the arrow to its stop and remove the tool. 199 11. Lower the rear window section of the convertible top down and lock into the tonneau cover.
WHAT TO DO IN EMERGENCIES 12. Fold down the locking latch handle. 13. Turn the latch handle just past one quarter turn clockwise and pull the convertible top frame carefully down until it meets the windshield header attachment points. 15. Fold the latch handle up. The convertible top is now locked onto the windshield header. 14. Turn the latch handle counterclockwise to the stop in order to lock the convertible top.
WHAT TO DO IN EMERGENCIES 201 Opening a Locked Decklid It is possible for the decklid to become locked if a convertible top system malfunction occurs. If the top is manually moved to the full up or full down position when the hydraulic pressure is relieved, the decklid should unlock.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 3.2L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 205 ▫ Power Steering Fluid . . . . . . . . . . . . . . . . . . . 217 䡵 Onboard Diagnostic System (OBD II) . . . . . . . 206 ▫ Chassis Lubrication . . . . . . . . . . . . . . . . . . . . 218 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . . 218 䡵 Replacement Parts . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Manual Transmission . . . . . . . . . . . . . . . . . . 229 ▫ Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . 244 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 ▫ Front Turn Signal And Parking/Standing Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245 䡵 Convertible Top Care . . . . . . . . . . . . . . . . . . . 234 ▫ Front And Rear Sidemarker Lights . . . . . . . . .
MAINTAINING YOUR VEHICLE 205 3.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) To meet new government regulations and promote cleaner air, your Crossfire is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions and engine control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the CHECK ENGINE Light is functioning and is not on when the engine is running, and that the OBD (Onboard Diagnostic) system is ready for testing.
MAINTAINING YOUR VEHICLE If your OBD system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update. A recheck with the above test routine may then indicate that the system is now ready.
MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent technician. MAINTENANCE PROCEDURES The pages that follow contain the maintenance service recommended by the engineers who designed your vehicle.
MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off, or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between the MIN and MAX markings on the dipstick. Adding 1 quart of oil when the reading is at the MIN mark will result in a MAX reading on this engine.
MAINTAINING YOUR VEHICLE Change Engine Oil The oil change interval for your Crossfire is initially set at 7,000 miles (Canada: 11,000 km). The Flexible Service System (FSS) in your vehicle evaluates engine temperature, oil level, vehicle speed, engine speed, distance driven, and the time elapsed since your last service. It determines when your vehicle needs maintenance service and alerts you in advance. The next necessary service is indicated by the FSS in your instrument cluster.
MAINTAINING YOUR VEHICLE Engine Oil Selection For best performance and maximum protection under all types of operating conditions, only use synthetic engine oils, approved to MB 229.3 or MB 229.5, such as Mobil 1 SAE 0W-40. The FSS may not alert for an oil change at the proper interval if an unapproved engine oil is used; engine damage and reduced engine life may result. Materials Added To Engine Oils Do not add materials (other than leak detection dyes) to engine oil.
MAINTAINING YOUR VEHICLE 213 Drive Belts - Check Condition and Tension At the distance shown in the maintenance schedules, check all drive belts for condition and proper tension. Improper belt tension can cause belt slippage and failure. Engine Air Cleaner Filter Under normal driving conditions, replace the air filter at each interval called out by FSS. Inspect the drive belts for evidence of cuts, cracks, or glazing and replace them if there is any sign of damage which could result in belt failure.
MAINTAINING YOUR VEHICLE Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly serviced to assure proper catalyst operation and prevent possible catalyst damage. If the CHECK ENGINE light is flashing, immediate service is required.
MAINTAINING YOUR VEHICLE • Do not idle the engine with any spark plug wires disconnected for a prolonged period. Ignition Wiring System The ignition cables should be kept clean and properly connected. Terminals should be fully seated. Cracked, damaged, or faulty cables should be replaced. Crankcase Emission Control System Proper operation of this system depends on freedom from sticking or plugging due to deposits. Check ventilation hose for indication of damage or plugging deposits. Replace if necessary.
MAINTAINING YOUR VEHICLE CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion. Apply grease to posts and clamps after tightening.
MAINTAINING YOUR VEHICLE Power Steering Fluid No power steering fluid service is required. The system is filled at the factory with Pentosin CHF 11S. Steering noise and reduced component life may result if an unapproved fluid is used. 217 Before removing the reservoir cap, wipe the outside of the cap and reservoir so that no dirt can fall into the reservoir. The power steering pump has a dipstick. Fluid level should be maintained at the proper level indicated on the dipstick.
MAINTAINING YOUR VEHICLE Chassis Lubrication Front Suspension Ball Joints There are two front suspension lower ball joints that are permanently lubricated. Inspect these ball joints whenever under-vehicle service is done. Steering Linkage Inspect tie rod ends whenever the vehicle is serviced. They are permanently lubricated and do not require periodic lubrication. Drive Shaft Universal Joints Your vehicle has four constant velocity universal joints.
MAINTAINING YOUR VEHICLE 219 Insert the key into the lock cylinder and rotate from the unlocked to the locked position without adding more lubricant. Repeat this procedure three or four times. Wipe all the lubricant off the key with a clean cloth, to avoid soiling clothing. Windshield Wiper Blade Replacement Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non-abrasive cleaner, or use the washer solvent.
MAINTAINING YOUR VEHICLE Windshield Washer Reservoir The washer fluid reservoir is located in the engine compartment and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) rated not to freeze at -25°F (-31°C). Operate the system for a few seconds to flush out the residual water. WARNING! Do not overfill the washer reservoir. Do not attempt to fill to the top of the filler neck.
MAINTAINING YOUR VEHICLE Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system, or if exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent technician inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition key is in the ON position. • You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool.
MAINTAINING YOUR VEHICLE If the solution is dirty and contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Engine Coolant Disposal Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community.
MAINTAINING YOUR VEHICLE Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing, according to the temperatures occurring in the area where the vehicle is operated. Cooling System Pressure Cap The cap must be fully tightened to prevent loss of coolant, and to insure that coolant will return to the radiator from the coolant reserve tank. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.
MAINTAINING YOUR VEHICLE • If frequent coolant additions are required, or if the level in the recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks. • Maintain a coolant concentration of a minimum of 50% ethylene glycol Extended Life Coolant and high quality water with recommended antifreeze for proper corrosion protection of your engine cooling system that contains aluminum components.
MAINTAINING YOUR VEHICLE WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency. Brake and Power Steering System Hoses When servicing the vehicle for scheduled maintenance, inspect surface of hoses and nylon tubing for evidence of heat and mechanical damage.
MAINTAINING YOUR VEHICLE Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning light is on. Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reservoir. Fluid level can be expected to fall as the brake pads wear. Brake fluid level should be checked when pads are replaced.
MAINTAINING YOUR VEHICLE CAUTION! CAUTION! Do not allow petroleum-based fluid to contaminate the brake fluid as seal damage will result! Using a transmission fluid other than the fluid recommended by DaimlerChrysler Corporation may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the DaimlerChrysler Corporation will result in more frequent fluid and filter changes.
MAINTAINING YOUR VEHICLE NOTE: Refer to Section 8 of this manual for Maintenance Schedules. Manual Transmission Selection of Lubricant No fluid service is required. Use only fluid approved to MB 236.2. SAE 5W-20 engine oil, meeting API SL or GF-3, may be substituted. Refer to the Recommended Fluids, Lubricants and Genuine Parts section for the correct fluid type. Fluid Level Check Check the fluid level by removing the fill plug.
MAINTAINING YOUR VEHICLE Appearance Care and Protection from Corrosion • Stone and gravel impact. Protection of Body and Paint from Corrosion Vehicle body protection requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
MAINTAINING YOUR VEHICLE CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels and rear liftgate / decklid be kept clear and open.
MAINTAINING YOUR VEHICLE When cleaning extremely dirty wheels, care must be taken in the selection of tire and wheel cleaning chemicals and equipment to prevent damage to the wheels. Only Mopar威 Wheel Cleaners are recommended. Any of the “DO NOT USE” items listed below can damage wheels and wheel trim. DO NOT USE: • Any abrasive cleaner • Any abrasive cleaning pad (such as steel wool) or abrasive brush • Any cleaner that contains an acid which can react with and discolor the chrome surface.
MAINTAINING YOUR VEHICLE 233 ammonia based cleaners to clean your leather upholstery. Application of a leather conditioner is not required to maintain the original condition. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. CAUTION! Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses.
MAINTAINING YOUR VEHICLE Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in the vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. • Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. • Dry with a soft tissue.
MAINTAINING YOUR VEHICLE Washing 235 General Cleaning CAUTION! • Remove bird droppings immediately. The organic acid can damage the material and cause the top to leak. • Never use a power washer to clean the top, as you may damage the top material. • If an automatic car wash is used, never use hotwax. Hand washing is highly recommended. Automatic car washing equipment can damage the top material. If you must use an automatic car wash, soft cloth systems are preferred.
MAINTAINING YOUR VEHICLE The following methods are sufficient if the top is only lightly soiled: Dry Cleaning Brush the dry top with a soft-bristled brush from front to rear of the vehicle. Wet Cleaning Wash with clear water or with a mild detergent and an ample supply of luke warm water by wiping with a soft-bristled brush or sponge from front to rear. Then rinse thoroughly with clear water. Allow the top to dry before lowering.
MAINTAINING YOUR VEHICLE 237 FUSES Underhood Accessory Fuse Block Fuses The underhood accessory fuse block fuses are located under the hood on the driver’s side, between the brake master cylinder and the left front fender. To remove the lid, squeeze the tabs together located at the front of the fusebox. Then lift the lid up by the tabs. The lid will then slide off the top of the fuse box. To replace the lid, place the two hinge-like tabs at the rear of the lid under the tabs on the fusebox.
MAINTAINING YOUR VEHICLE CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it shows a problem in the circuit that must be corrected.
MAINTAINING YOUR VEHICLE Underhood Accessory Fuse Block Fuses Cavity 1 2 3 4 5 5 6 6 7 Fuse 5 Amp Beige 5 Amp Beige 5 Amp Beige 7.
MAINTAINING YOUR VEHICLE Cavity 18 19 20 21 22 23 24 25 26 30 30 Fuse 40 Amp Orange 40 Amp Orange 30 Amp Green 30 Amp Green 30 Amp Green 15 Amp Blue 30 Amp Green 20 Amp Yellow 20 Amp Yellow 15 Amp Blue Circuits Electronic Stability Program Cavity 31 Power Window, Front 32 Wiper Motor 33 Seat Adjustment Right Side 34 34 Seat Adjustment Left Side 35 Sound Booster (Amplifier) Fuse 15 Amp Blue 15 Amp Blue 5 Amp Beige 30 Amp Green 15 Amp Blue Seat Heater 36 Pneumatic Control Unit, Rear Window D
MAINTAINING YOUR VEHICLE 241 Relay Control Module Fuses The relay control module fuses are located in the Control Module Box next to the battery in the engine compartment. Slide the control module box cover retaining clips forward and lift the cover from the control module box to gain access to the relay control module fuses.
MAINTAINING YOUR VEHICLE Interior Fuses The fuse access door is located on the end of the instrument panel on the driver’s side behind the trim panel cover. Use a coin or flat blade screwdriver to open and close this access door. Interior Fuses Cavity Fuse 1 2 15 Amp Blue 3 7.5 Amp Brown 4 15 Amp Blue 5 7.
MAINTAINING YOUR VEHICLE Cavity 6 7 8 9 10 11 12 13 14 Fuse 15 Amp Blue 7.5 Amp Brown 15 Amp Blue 15 Amp Blue 7.5 Amp Brown 7.
MAINTAINING YOUR VEHICLE EXTERIOR LIGHT BULB SERVICE Headlights WARNING! Halogen lamps contain pressurized gas. A bulb can explode if you: • Touch or move it when hot • Drop the bulb • Scratch the bulb Wear eye and hand protection. NOTE: To prevent a possible electrical short circuit, switch off light prior to replacing a bulb. 1. Push the tab down at the top end of the cover and remove. 2. Disconnect the electrical connector. 3.
MAINTAINING YOUR VEHICLE 245 Front Turn Signal and Parking/Standing Lights • Twist the bulb socket counterclockwise and pull out. Push the bulb into the socket, turn counterclockwise and remove. • Replace the bulb, push in and twist clockwise. Reinstall the socket, and turn clockwise. Front and Rear Sidemarker Lights 1. Push the front sidemarker assembly in and slide it forward. Push the rear sidemarker assembly in and slide rearward. The assembly will release from the fascia. 2.
MAINTAINING YOUR VEHICLE 4. Replace the access door in the trim panel. NOTE: Always test the operation of all lights after service operations have been performed to validate an effective repair. License Plate Light 1. Remove the two lens assembly mounting screws. 2. Pull the bulb out of the socket. 3. Replace the bulb and reattach the lens assembly. 4. Align and resecure the two lens assembly mounting screws.
MAINTAINING YOUR VEHICLE the vehicle and then readjust the headlights to the original position. If any further adjustments are necessary contact your manufacturer’s dealer. A detailed service procedure is contained in the manufacturer’s Service Manual. Information on purchasing a Service Manual can be found at the back of this Owner’s Manual. VEHICLE STORAGE We recommend that you follow these guidelines before storing your Crossfire for extended periods. • Fill the gas tank.
MAINTAINING YOUR VEHICLE Check the battery every four to six weeks to ensure that the voltage is above 12.40. Voltage will drop more rapidly in hot temperatures. If battery voltage drops below 12.40, follow the battery recharge procedure in the Service Manual. • Check that the radiator coolant level of protection is to at least -20°F (-29°C). • Block the wheels. Do not apply the parking brake. • Make sure that all tires are inflated to the optimum pressure.
MAINTAINING YOUR VEHICLE SPECIFICATIONS Performance Specifications (approximate) Engine Specifications Maximum Speed Acceleration 0–60 mph 1/4 mile time Engine Size Mode of Operation No. of Cylinders Horsepower (SAE J 1349) Bore Stroke Torque (SAE J 1349) Firing Order Compression Ratio Spark Plugs Spark Plug Gap Tightening Torque Maximum Engine Speed Accessory Drive Belt 195.2 CID (3.2 Liters) 4–stroke engine, gasoline injection 6 215 hp (160 kW) @ 5700 rpm 3.54 in. (89.90 mm) 3.30 in. (84.
MAINTAINING YOUR VEHICLE Body Specifications Overall Length Maximum Width Maximum Width With Mirrors Overall Height Coupe: Roadster: Front Track Rear Track Wheelbase Front Overhang Rear Overhang Front Ground Clearance 159.8 in. (4058 mm) 69.5 in. (1766 mm) 76.9 in. (1954 mm) 51.5 in. (1307 mm) 51.8 in. (1315 mm) 58.8 in. (1493 mm) 59.1 in. (1502 mm) 94.5 in. (2400 mm) 32.4 in. (822 mm) 32.9 in. (836 mm) 5.0 in.
MAINTAINING YOUR VEHICLE 251 FLUID CAPACITIES U.S. 15.8 Gallons 2 Gallons Metric 60.0 Liters 7.5 Liters 3.2 L Engine 8.5 Qts. 8.0 Liters 3.2 L Engine 11.8 Qts. 1.9 Qts. 8.5 Qts. 1.4 Qts. 1.1 Qts. .5 Qts. 7.4 Qts. 11.2 Liters 1.8 Liters 8.0 Liters 1.3 Liters 1.0 Liters .5 Liters 7.
MAINTAINING YOUR VEHICLE RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Spark Plug Gap Fuel Selection Fluids, Lubricants and Genuine Parts Use coolant approved to MB 325.0, such as Valvoline GO5, or an equivalent extended life coolant. Only use synthetic engine oils, approved to MB 229.3 or MB 229.5, such as Mobil 1 SAE 0W-40.
MAINTAINING YOUR VEHICLE 253 Chassis Component Automatic Transmission Brake Master Cylinder Clutch Fluid Manual Transmission Fluid Power Steering Reservoir Rear Axle Fluid Tire Pressure Fluids, Lubricants and Genuine Parts Only use ATF approved to MB 236.10, MB 236.12. Synthetic Dexron III威 Transmission Fluid may be substituted. Use brake fluid approved to MB 331.
MAINTAINING YOUR VEHICLE Body Component Hinges: Fluids, Lubricants and Genuine Parts Door Mopar威 Spray White Lube Liftgate / Decklid Mopar威 Multi-Purpose Lube NLGI Grade 2 EP, GC-LB Hood Springs and Links Mopar威 Spray White Lube Latches: Liftgate/Decklid Hood/Safety Catch Door Seat Regulator and Track Window System Components Lock Cylinders Spoiler Mopar威 Mopar威 Mopar威 Mopar威 Mopar威 Mopar威 Mopar威 Spray White Lube Multi-Purpose Lube NLGI Grade 2 EP, GC-LB Spray White Lube Multi-Purpose Lube NLGI Gr
MAINTENANCE SCHEDULES CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 256 䡵 Regular Check-Ups . . . . . . . . . . . . . . . . . . . . . 261 M A I N T E N A N C E S 䡵 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 ▫ Additional Periodic Maintenance . . . . . . . . . . 262 C 䡵 Emission Control System Maintenance . . . . . . 257 䡵 Special Maintenance Requirements . . . . . . . . . 264 E 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E S C H E D U L E S 8 256 MAINTENANCE SCHEDULES INTRODUCTION This is intended as a guide to the service requirements of your vehicle. It contains all necessary instructions concerning service intervals and operations which have to be carried out. Scope and frequency of maintenance work primarily depend on the vehicle’s operating conditions. In the interest of maintaining the vehicle’s operating safety, the specified work should be performed regularly and in good time.
MAINTENANCE SCHEDULES The use of Special lubricant additives is not recommended. The use of such additives may affect your warranty rights. With regard to legal stipulations concerning emissions control, please note that engines have to be serviced and adjusted in accordance with special instructions and using special measuring equipment. Modifications to or interference with the emissions control systems are not permissible.
M A I N T E N A N C E S C H E D U L E S 8 258 MAINTENANCE SCHEDULES Your Flexible Service System (FSS) — see Understanding Your Instrument Panel section — should give you an exact indication of when your vehicle should be scheduled for service and which schedule to follow. • Windshield wipers and washer system Additional Periodic Maintenance items should also be performed beyond the items listed in the following charts to assure the optimum performance of your Crossfire.
MAINTENANCE SCHEDULES SCOPE OF WORK FOR “B” SCHEDULE MAINTENANCE SERVICE Oil Change • Change oil and replace filter Maintenance • Rotate tires • Replace dust filter (if equipped) • Lubricate hood hinges, latch, and secondary latch • Reset FSS Display Function Check • Horn, hazard warning flashers, turn signals, and indicator lamps 259 M A I N front and rear brake pads for lining thickness T E N condition of front and rear brake discs A N tires for damage and general condition C tire inflation pressures a
M A I N T E N A N C E 260 S C H E D U L E S • Hydraulic brake system − Driving in dusty conditions. • Power steering system − Short trips of less than 10 miles (16 km). • Windshield washer system − More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C). FSS SYSTEM The Flexible Service System (FSS) permits a flexible service schedule that is directly related to the operating conditions of the vehicle.
MAINTENANCE SCHEDULES The next service is normally calculated and displayed next to the Service A or Service B symbol as distance remaining before the next service is required. Depending on operating conditions throughout the year, a clock symbol may appear next to the service symbol. When this occurs, the next service is calculated and displayed in days remaining before the next service is required. You should have the maintenance performed within the stated time period or distance.
M 262 MAINTENANCE SCHEDULES A I At Each Stop for Fuel N T • Check the engine oil level about 5 minutes after a fully E warmed engine is shut off. Checking the oil level while N A the vehicle is on level ground will improve the accuN racy of the oil level reading. See the procedure deC scribed in Checking Your Engine Oil in the UnderE S C H E D U L E S 8 standing Your Instrument Panel section or under Engine Oil in the Maintaining Your Vehicle section.
MAINTENANCE SCHEDULES 263 M A At approximately every 50,000 miles (80,000 km) or 4 years: At approximately every 100,000 miles (161,000 km) or 5 I N years: T • Check condition of driveshaft flex discs. • Replace spark plugs. • Retighten locking bolts for steering (observe torque). At approximately every 60,000 miles (96,000 km) or 4 years: • Replace fuel filter. • Replace air cleaner filter element. At approximately 80,000 miles (129,000 km): • Change the automatic transmission fluid and filter.
M A I N T E N A N C E S C H E D U L E S 8 264 MAINTENANCE SCHEDULES SPECIAL MAINTENANCE REQUIREMENTS Coolant Have the corrosion inhibitor/antifreeze concentration in the coolant checked before the onset of winter (once a year in countries with high prevailing temperatures). Have the coolant replaced every five years or 100,000 miles (160,000 km). Dust Filter for Heating/Ventilation Replacement (If Equipped) The dust filter is replaced during routine maintenance service.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266 ▫ Prepare For The Appointment . . . . . . . . . . . . 266 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 266 ▫ Be Reasonable With Requests . . . . . . . . . . . . . 266 䡵 If You Need Assistance . . . . . . . . . . . . . . . . . . 266 䡵 Warranty Information . . . . . . . . . . . . . . . . . . . 269 䡵 Mopar威 Parts . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty; discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a valuable clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the DaimlerChrysler Corporation’s Customer Center.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the DaimlerChrysler Corporation has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the DaimlerChrysler Corporation by dialing 1-800-380-CHRY.
IF YOU NEED CONSUMER ASSISTANCE WARRANTY INFORMATION See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your authorized dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 states of the United States and Washington, D.C.
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.
IF YOU NEED CONSUMER ASSISTANCE TIRE SAFETY INFORMATION Tire Markings 271 NOTE: European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H. NOTE: LT(Light Truck)-Metric tire sizing is based on U.S. design standards.
IF YOU NEED CONSUMER ASSISTANCE EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ...blank...ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
IF YOU NEED CONSUMER ASSISTANCE 273 Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. i.e. tire pressure, vehicle loading, road conditions and posted speed limits.
IF YOU NEED CONSUMER ASSISTANCE Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
IF YOU NEED CONSUMER ASSISTANCE Tire Loading and Tire Pressure 275 Tire and Loading Information Placard Tire Placard Location NOTE: Some vehicles have a “Tire and Loading Information” placard located on the driver’s side “B” pillar. This placard tells you important information about: 1. the number of people that can be carried in the vehicle 2. the total weight your vehicle can carry 3. the tire size designed for your vehicle 4. the cold tire inflation pressures for the front, rear and spare tires.
IF YOU NEED CONSUMER ASSISTANCE Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
IF YOU NEED CONSUMER ASSISTANCE 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE: The following table shows examples on how to calculate total load, cargo/luggage and towing capacities of your vehicle with varying seating configurations and 277 number and size of occupants.
IF YOU NEED CONSUMER ASSISTANCE
IF YOU NEED CONSUMER ASSISTANCE 279 WARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle-never overload them.
INDEX 10
INDEX ABS (Anti-Lock Brake) System . . . . . . . . . . . . . 111 Adding Engine Coolant (Antifreeze) . . . . . . . . . 223 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 173 Aiming Headlights . . . . . . . . . . . . . . . . . . . . . . 246 Air Cleaner, Engine (Engine Air Cleaner Filter) . 213 Air Conditioning . . . . . . . . . . . . . . . . . . . . 128,216 Air Conditioning Filter . . . . . . . . . . . . . . . . . . . 264 Air Conditioning Refrigerant . . . . . . . . . . . . . .
INDEX Carbon Monoxide Warning . . . . . . . . . . . . . . . . 47 Cargo Compartment Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 Catalytic Converter . . . . . . . . . . . . . . . . . . . . . 214 CD Player . . . . . . . . . . . . . . . . . . . . . . . . . 119,123 Chains, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . 180 Charging System Light . . . . . . . . . . . . . . . . . . . 112 Checks, Safety . . . . .
INDEX Disposal Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 212 Door Locks, Automatic . . . . . . . . . . . . . . . . . . . 13 Drive Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 Drive Shaft Universal Joints . . . . . . . . . . . . . . . 218 Driving On Slippery Surfaces . . . . . . . . . . . . . . . . . . 189 Electronic Speed Control . . . . . . . . . . . . . . . . . . 94 Electronic Stability Program . . . . . . . . . . . . . . . .
INDEX Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237 Garage Door Opener . . . . . . . . . . . . . . . . . . . . . 97 Gas Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251 Gasoline/Oxygenate Blends . . . . . . . . . . . . . . . 171 Gear Ratios . . . . . . . . . . . . . . . . . . . . . . . . . . . 249 General Information . . . . . . . . . . . . . . . . . . . . . 167 Glass Cleaning . . . . . . .
INDEX Lights Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . 32,116 Anti-Lock Warning . . . . . . . . . . . . . . . . . . . . 111 Back-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245 Daytime Running . . . . . . . . . . . . . . . . . . . . . . 77 Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Exterior Check . . . . . . . . . . . . . . . . . . . . . . . . 48 Fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Hazard Warning Flasher .
INDEX Mopar Parts . . . . . . . . . . . . . . . . . . . . . . . . 208,269 Multi-Function Control Lever . . . . . . . . . . . . . . . 78 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . . 22 Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 209 Change Interval . . . . . . . . . . . . . . . . . . . . . . 211 Checking . . . . . . . . . . . . . . . . . . . . . . . . . . . 209 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212 Filter . . . . . . . . . . . . . . . .
INDEX Safety Checks Inside Vehicle . . . . . . . . . . . . . . . 48 Safety Checks Outside Vehicle . . . . . . . . . . . . . . 48 Safety Information, Tire . . . . . . . . . . . . . . . . . . 159 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Schedule, Maintenance . . . . . . . . . . . . . . . . . . . 257 Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 And Pregnant Women . . . . . . . . . . . . . . . . . . 28 Extender . . . . . . . . . . . . . . . . .
INDEX Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . 165 Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 Changing . . . . . . . . . . . . . . . . . . . . . . . . 180,184 General Information . . . . . . . . . . . . . . . . . . . 159 High Speed . . . . . . . . . . . . . . . . . . . . . . . . . 161 Inflation Pressures . . . . . . . . . . . . . . . . . 160,275 Load Capacity . . . . . . . . . . . . . . . . . . . . . . . 275 Pressure Monitor System . . . . . . . . . . . . .
INDEX Washer, Adding Fluid . . . . . . . . . . . . . . . . . . . 220 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . 230 Wheel Alignment and Balance . . . . . . . . . . . . . 165 Wheel and Wheel Trim Care . . . . . . . . . . . . . . . 231 Windows Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Windshield Defroster . . . . . . . . . . . . . . . . . . . . . 48 Windshield Washers . . . . . . . . . . . . . . . . . . . . . 80 Windshield Wiper Blades . . . . . . . . . .
NOTES
NOTES
NOTES
NOTES
NOTES
NOTES
