SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications / Alterations . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures, which could result in an accident or bodily injury. It also contains CAUTIONS against procedures, which could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is on the left front corner of the instrument panel.
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS 1 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . .11 䡵 Illuminated Entry System . . . . . . . . . . . . . . . . .17 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .11 䡵 Remote Keyless Entry . . . . . . . . . . . . . . . . . . . .17 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .12 ▫ To Unlock The Doors . . . . . . . . . . . . . . . . . . .18 䡵 Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Power Door Locks . . . . . . . . . . . . . . . . . . . . .21 ▫ Seat Belts And Pregnant Women . . . . . . . . . . . .37 ▫ Child Protection Door Lock . . . . . . . . . . . . . . .23 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . .37 䡵 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 ▫ Driver And Front Passenger Supplemental Restraint System (SRS) - Airbag . . . . . . . . . . . .38 ▫ Power Windows . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS You can insert the double-sided keys into the locks with either side up. 11 Ignition Key Removal The shift lever must be in PARK. Turn the key to the LOCK position, and then remove the key. Vehicle Key Ignition Key Positions The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exit,” under “Personal Settings (Customer Programmable Features),” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. Key-In-Ignition Reminder If you open the driver’s door and the key is in the ignition switch, a chime will sound to remind you to remove the key. WARNING! NOTE: The Key-In-Ignition reminder only sounds when the ignition key is placed in the LOCK or ACC positions. Never leave children alone in a vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: A key, which has not been programmed, is also considered an invalid key even if it is cut to fit the ignition lock cylinder for that vehicle. During normal operation, after turning on the ignition switch, the Vehicle Security Alarm Indicator Light will turn on for three (3) seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE consists of programming a blank key to the vehicle electronics. A blank key is one, which has never been programmed. NOTE: When having the Sentry Key Immobilizer System serviced, bring all vehicle keys with you to the dealer. Customer Key Programming If you have two valid sentry keys, you can program new sentry keys to the system by performing the following procedure: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information The Sentry Key system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received, including interference that may cause undesired operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Disarm the System: Either press the UNLOCK button on the remote keyless entry transmitter or insert a valid sentry key into the ignition lock cylinder and turn the key to the ON/START position. NOTE: • The driver’s door key cylinder and the trunk button on the keyless entry transmitter cannot arm or disarm the system. • The system remains armed during trunk entry. Pressing the trunk button will not disarm the system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ILLUMINATED ENTRY SYSTEM The courtesy lights will turn on when you use the keyless entry transmitter or open the doors. The lights will fade to off after about 30 seconds or they will immediately fade to off once the ignition switch is turned ON from the LOCK position. NOTE: • None of the courtesy lights will operate if the dimmer control is in the “defeat” position (extreme downward position), unless the overhead map/reading lights are turned on manually.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To unlock the doors: Press and release the UNLOCK button on the transmitter once to unlock the driver’s door, or twice to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on. Remote Key Unlock, Driver Door/All Doors First This feature lets you program the system to unlock either the driver’s door or all doors on the first press of the UNLOCK button on the transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lock,” under “Personal Settings (Customer Programmable Features),” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. To unlatch the trunk: Press the trunk button on the transmitter two times to unlatch the trunk. Using The Panic Alarm: To turn the panic alarm feature ON or OFF, press and hold the PANIC button on the transmitter for at least one second and release.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. Separating Transmitter Halves 3. Remove and replace the battery. Avoid touching the new battery with your fingers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS 21 WARNING! Manual Door Locks To lock each door, push the door lock plunger on each door trim panel downward. To unlock each door, pull the door lock plunger on each door trim panel upward. Door Lock Plunger If the door lock plunger is down when you shut the door, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Door Locks The doors will lock automatically on vehicles with power door locks if all of the following conditions are met: 1. The Automatic Door Locks feature is enabled. 2. The transmission is in gear. 3. All doors are closed. 4. The throttle is pressed. 5. The vehicle speed is above 15 mph (24 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Unlock Doors on Exit The doors will unlock automatically on vehicles with power door locks if: 1. The Automatic Unlock Doors On Exit feature is enabled. 2. The transmission was in gear and the vehicle speed returned to 0 mph (0 km/h). 3. The transmission is in NEUTRAL or PARK. 23 Child Protection Door Lock To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a child protection door lock system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Repeat Steps 1 and 2 on the opposite rear door. To Disengage the Child Protection Door Lock NOTE: When the child lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position. 1. Open the rear door. 2. Insert the tip of the vehicle’s ignition key or alike into the child lock control and pull it downward. WARNING! Avoid trapping anyone in a vehicle in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS 25 WARNING! Power Windows The window controls on the driver’s door control all the door windows. Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power window switches will remain active for up to 60 minutes after the ignition switch is turned off. Opening either front door will cancel this feature. The time for this feature is programmable. For details, refer to “Delay Power Off to Accessories Until Exit,” under “Personal Settings (Customer Programmable Features),” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Window Lockout Switch The window lockout switch on the driver’s door allows you to disable the window controls on the passenger doors. When the switch is pressed, the window controls on the passenger doors will not illuminate and the passenger windows will be disabled. 27 Reset Any time the vehicle battery is disconnected, or goes dead, the auto-up function will be disabled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE buffeting occurs with the sunroof open, then adjust the sunroof opening to minimize the buffeting. TRUNK LOCK AND RELEASE The trunk lid can be released from inside the vehicle by pressing the Trunk Release Button located on the instrument panel to the left of the steering wheel. NOTE: The transmission must be in Park before the switch will operate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK SAFETY WARNING 29 Trunk Emergency Release WARNING! 2 Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat. If trapped in the trunk, children can die from suffocation or heat stroke.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger and, if so equipped, side curtain airbags for the driver and passengers seated next to a window.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Connecting Latch Plate To Buckle WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. 33 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly. 1. Position the latch plate as close as possible to the anchor point. The pretensioners are triggered by the Airbag Control Module (refer to information on Airbags in this section).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE BeltAlert Programming The Enhanced Warning System (BeltAlert) can be enabled or disabled by your authorized dealer or by performing the following steps: NOTE: Watch for the Seat Belt Reminder Light to turn on while unbuckling the seat belt and turn off while re-buckling the seat belt. It may be necessary to retract the seat belt. NOTE: DaimlerChrysler does not recommend deactivating the Enhanced Warning System (BeltAlert). 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE distinctive label on the webbing. Children 12 years old and under should be properly restrained in the rear seat whenever possible. How To Engage The Automatic Locking Mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will here a clicking sound. This indicates the safety belt is now in the automatic locking mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver and Front Passenger Supplemental Restraint System (SRS) - Airbag This vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s airbag is mounted in the center of the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Do not use a clothing bar mounted to the coat hooks in this vehicle. A clothing bar will impede the proper performance of the curtain airbags. Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Side Curtain Airbags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 8. The driver and front passenger seats should be moved back as far as practical to allow the airbags time to inflate. 9. If your vehicle has side curtain airbags do not lean against the door, airbags will inflate forcefully into the space between you and the door. 10. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Airbag Warning Light • Driver Airbag • Front Passenger Airbag • Supplemental Side Curtain Airbags above Side Windows (if equipped) • Steering Wheel and Column • Instrument Panel • Interconnecting Wiring • Seatbelt Reminder Light • Knee Impact Bolsters • Front Acceleration Sensors • Driver and Front Passenger Seat Belt Pretensioners How The Airbag System Works • The Airbag Control Module (ACM) determines if a frontal collision is severe enough to require the
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the AIRBAG Warning Light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away. • The Driver and Front Passenger Airbag/Inflator Units are located in the center of the steering wheel and the passenger side of the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Knee Impact Bolsters help protect the knees of the driver and the front passenger, and position everyone for the best interaction with the front airbag. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed airbags can’t protect you in another collision. Have the airbags replaced by an authorized dealer as soon as possible. Enhanced Accident Response Feature If the airbags deploy after an impact and the electrical system remains functional, vehicles equipped with power door locks will unlock automatically. In addition, approximately 5 seconds after the vehicle has stopped moving, the interior lights will illuminate to aid visibility.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light You will want to have the airbags ready to inflate for your protection in an impact. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system promptly: • The Airbag Warning Light does not come on or flickers during the 6 to 8 seconds when the ignition switch is first turned on. • The light remains on or flickers after the 6 to 8 second interval.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE treated confidentially. Confidential data will not be disclosed by DaimlerChrysler to any third party except when: 1. Used for research purposes, such as to match data with a particular crash record in an aggregate database, provided confidentiality of personal data is thereafter preserved 2. Used in defense of DaimlerChrysler product litigation involving a 3. Requested by police under a legal warrant 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward facing child restraint should only be used in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the child restraint using lower anchorages and upper tether straps from the child restraint to the vehicle structure. LATCH-compatible child restraint systems are now available. However, because the lower anchorages are to be introduced over a period of years, child restraint systems having attachments for those anchorages will continue to have features for installation using the vehicle’s seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provided with the child restraint system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children. It is recommended that before installing the child restraint, buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE a child restraint to be tightly installed. Refer to “Automatic Locking Mode” in this section for details. A locking clip should not be necessary once the automatic locking feature is enabled. Position the shoulder and lap belt on the child restraint. The automatic locking retractor is activated by first attaching the child seat, then pulling all of the webbing out of the retractor, then allowing back in. Tighten webbing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and remove slack in the tether strap according to the child restraint manufacturer’s instructions. NOTE: Ensure that the tether strap does not slip into the opening between the seat backs as you remove slack in the strap. WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! WARNING! Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. NOTE: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc. If there is any question regarding belt or retractor condition, replace the belt. Airbag Warning Light The light should come on and remain on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 ▫ Operations . . . . . . . . . . . . . . . . . . . . . . . . . . .67 ▫ Automatic Dimming Inside Mirror . . . . . . . . . .63 ▫ Phone Call Features . . . . . . . . . . . . . . . . . . . .73 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .63 ▫ UConnect™ System Features . . . . . . . . . . . . . .75 ▫ Exterior Mirrors Folding Feature — If Equipped . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Folding Rear Seat . . . . . . . . . . . . . . . . . . . . . .89 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . .98 䡵 Driver Memory Seat — If Equipped . . . . . . . . .90 ▫ Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . .98 ▫ Programming The Memory Feature . . . . . . . . .90 ▫ Multi-Function Lever . . . . . . . . . . . . . . . . . . . .98 ▫ Linking & Unlinking The Remote Keyless Transmitter To The Memory Feature . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 61 䡵 Electronic Speed Control . . . . . . . . . . . . . . . . . 109 ▫ Erasing HomeLink Buttons . . . . . . . . . . . . . . 120 ▫ Electronic Speed Control Operation . . . . . . . . 109 ▫ Reprogramming a Single HomeLink Button . . . 120 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . . 110 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 ▫ To Set At A Desired Speed . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Cup Holders . . . . . . . . . . . . . . . . . . . . . . . . . 126 䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 ▫ Front Seat Cup Holders . . . . . . . . . . . . . . . . . 126 ▫ Console Features . . . . . . . . . . . . . . . . . . . . . . 127 ▫ Rear Seat Cup Holders . . . . . . . . . . . . . . . . . 126 ▫ Cargo Area . . . . . . . . . . . . . . . . . . . . . . . . . . 127 䡵 Load Leveling System . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS 63 CAUTION! Automatic Dimming Inside Mirror This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated. To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side convex mirror. Exterior Mirrors Folding Feature — If Equipped Some models have exterior mirrors that are hinged.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65 Illuminated Vanity Mirrors An illuminated vanity mirror is on the sun visor. To use the mirror, rotate the sun visor downward and swing the mirror cover upward. The light turns on automatically. Closing the mirror cover turns off the lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in- vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone using simple voice commands (e.g., ⬙Call” ѧ “Mike” ѧ”Work⬙ or ⬙Dial” ѧ “248-555-1212⬙). Your cellular phone’s audio is transmitted through your vehicle’s audio system; the system will automatically mute your radio when using the UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 system can be adjusted either from the radio volume control knob, or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the UConnect™ system such as ⬙CELL⬙ or caller ID on certain radios. UConnect™ Switches The UConnect™ system can be used with any HandsFree Profile certified Bluetooth™ cellular phone. See www.chrysler.com/uconnect for supported phones.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For each feature explanation in this section, only the combined form of the voice command is given. You can also break the commands into parts and say each part of the command, when you are asked for it. For example, you can use the combined form voice command ⬙Phonebook New Entry,⬙ or you can break the combined form command into two voice commands: ⬙Phonebook⬙ and ⬙New Entry.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • www.jeep.com/uconnect The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing⬙ and follow the audible prompts. • When prompted, after the voice on beep, say ⬙Pair a Phone⬙ and follow the audible prompts. • You will be asked to say a four-digit pin number, which you will later need to enter into your cellular.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnect™ system will confirm the phone number and then dial. The number will appear in the display of certain radios. Call/Dial by Saying a Name • Press the “Phone” button to begin. • After the ⬙Ready⬙ prompt and the following beep, say “Dial” or Call.⬙ • System will prompt you to say the name of the person you want call. • After the ⬙Ready⬙ prompt and the following beep, say the name of the person you want to call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ system will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language. Edit Entries in the UConnect™ Phonebook NOTE: Editing phonebook entries is recommended when vehicle is not in motion. • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Edit.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE from which you choose. To select one of the entries from the list, press the ⬙Voice Recognition⬙ button while the UConnect™ system is playing the desired entry and say ⬙Delete.⬙ • After you enter the name, the UConnect™ system will ask you which designation you wish to delete, home, work, mobile, or pager. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone Call Features The following features can be accessed through the UConnect™ system if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the UConnect™ system. Check with your cellular service provider for the features that you have.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Toggling Between Calls If two calls are in progress (one active and one on hold), press the ’Phone’ button until you hear a single beep indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE until the vehicle battery condition dictates cessation of the call on the UConnect™ system and transfer of the call to the mobile phone. • After ignition key is switched to off, a call can continue on the UConnect™ system for certain duration, after which the call is automatically transferred from the UConnect™ system to the mobile phone. • An active call is automatically transferred to the mobile phone after ignition key is switched to off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The emergency number dialed is based on the Country where the vehicle is purchased (911 for USA and Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area. The UConnect™ system does slightly lower your chances of successfully making a phone call as to that for the cell phone directly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE You can use your UConnect™ system to access a voicemail system or an automated service, such as, paging service or automated customer service. Some services require immediate response selection, in some instances, that may be too quick for use of UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth™ cellular phone, the audio will be played through your vehicle’s audio system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Connect or Disconnect Link Between the UConnect™ System and Cellular Phone Your cellular phone can be paired with many different electronic devices, but can only be actively ⬙connected⬙ with one electronic device at a time. If you would like to connect or disconnect the Bluetooth™ connection between a UConnect™ paired cellular phone and the UConnect™ system, then follow the instruction described in your cellular phone user’s manual.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete UConnect™ Paired Cellular Phones • Performance is maximized under: • Press the ’Phone’ button to begin. • low-to-medium blower setting, • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing.⬙ • low-to-medium vehicle speed, • At the next prompt, say ⬙Delete⬙ and follow the prompts. • You can also press the ⬘Voice Recognition’ button anytime while the list is being played and then choose the phone you wish to delete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • UConnect™ phonebook nametag recognition rate is optimized for the voice of the person who stored the name in the phonebook. • You can say ⬙O⬙ (letter ⬙O⬙) for ⬙0⬙ (zero). ⬙800⬙ must be spoken ⬙eight-zero-zero.⬙ • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE North American English Primary Alternate(s) Zero Oh Add location Add new All All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing Pairing Phonebook Phone book Return to main menu Return.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. CAUTION! Do not place any article under a power seat as it may cause damage to the seat controls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lumbar Support This feature allows you to increase or decrease the amount of lumbar support. Turn the control lever forward to increase and rearward to decrease the desired amount of lumbar support. 87 The head restraints have a locking button, which must be pushed in to lower the head restraint. The restraints may be raised without pushing in the button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ignition, you can choose from High, Off, or Low heat settings. Amber LEDs in the top portion of each switch indicate the level of heat in use. Two LEDs will illuminate for high, one for low, and none for off. LEDs changes from two to one, indicating the change. Operation on the low setting also turns off automatically after 30 minutes. NOTE: Once a heat setting is selected, heat will be felt within two to five minutes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat Folding Rear Seats The rear seatbacks can be folded forward to provide an additional storage area. Pull on the loops shown in the illustration to fold down either or both seatbacks. These loops can be tucked away when not in use. When the seatback is folded to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat strap.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER MEMORY SEAT — IF EQUIPPED This feature allows the driver to store up to two different memory profiles, for easy recall through a memory switch. Each memory profile contains desired position settings for the driver seat, side mirror, adjustable pedals, and power tilt and telescopic steering column, and a set of desired radio station presets. The memory switch is located on the driver’s door panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Press and release the Set (S) button on the memory switch, then press the side of the rocker switch labeled (1) within 5 seconds. The Electronic Vehicle Information Center (EVIC) will display which memory position is being set. If desired, a second memory profile can be stored into memory as follows: 1. Adjust all memory profile settings to desired preferences (i.e.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Your transmitters can be unlinked to your memory settings by pressing the Set (S) button followed by the UNLOCK button on the transmitter in Step 4 above. Memory Position Recall NOTE: The vehicle must be in Park to recall memory positions. If a recall is attempted when the vehicle is not in Park, a message will display in the Electronic Vehicle Information Center (EVIC).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE is between 2.4 inches and 3.5 inches (60 mm and 90 mm) forward of the rear stop. The seat will return to its previously set position when you insert the key into the ignition switch and turn it out of the LOCK position. TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood. First, pull the hood release lever located under the left side of the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Next, move to the outside of the vehicle and push the safety catch to the left. The safety catch is located under the center front edge of the hood. Use the hood prop rod (if equipped) to secure the hood in the open position. To prevent possible damage, do not slam the hood to close it. Lower the hood, until it is open approximately 6 inches (15 cm), and then drop it. This should secure both latches.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Headlight Switch The headlight switch is located on the left side of the instrument panel. This switch controls the operation of the headlights, parking lights, instrument panel lights, instrument panel light dimming, interior lights, and fog lights. Headlight Switch 95 Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Headlights On with Wipers feature can be enabled or disabled. For details, refer to ”Headlights On with Wipers,” under “Personal Settings (Customer Programmable Features),” under “Electronic Vehicle Information Center” in Section 4 of this manual. Headlight Switch NOTE: The engine must be running before the headlights will come ON in the Automatic mode.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Push the Multi-Function Lever away from you to switch the headlights to the HIGH BEAM position. NOTE: This system will not activate until the vehicle is at or above 25 mph (40 km/h). 97 Headlight Time Delay This feature provides the safety of headlight illumination for 90 seconds (programmable) when leaving your vehicle in an unlighted area. To Deactivate: Perform either of the following steps to deactivate the SmartBeam system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights (Canada Only) The high beam headlights will come on as Daytime Running Lights, whenever the ignition switch is on, the headlights are off, and the parking brake is off. The headlight switch must be used for normal nighttime driving. Multi-Function Lever The multi-function lever controls the operation of the turn signals, headlight beam selection, and passing lights. The lever is located on the left side of the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE by moving the lever partially up or down without moving beyond the detent. Releasing the lever at the detent will provide 3 flashes. If either light has a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the fuse or indicator is defective or there may be a circuit failure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights The interior lights come on when a door is opened. To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position. This will occur if the interior lights were switched on manually or are on because a door is open. This includes the glove box light, but not the trunk light.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The multi-function lever operates the windshield wipers and washer when the ignition switch is in the ON position. The lever is located on the left side of the steering column. Windshield Wiper/Washer Control Rotate the end of the multi-function lever to the first detent past the intermittent settings for Low-speed wiper operation, or to the second detent past the intermittent settings for High-speed wiper operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! two wipe cycles after releasing the lever and then resume the intermittent interval previously selected. Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during windshield washer use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 the end of the multi-function lever to one of the six intermittent wiper settings to activate this feature. Features),” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. The sensitivity of the system is adjustable from the multi-function lever. Wiper delay position 1 is the least sensitive and wiper delay position 6 is the most sensitive. Choose setting 3 or 4 for normal rain conditions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adding Washer Fluid The windshield washer fluid reservoir is located in the front of the engine compartment on the passenger side of the vehicle. Be sure to check the fluid level in the reservoir at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE HEADLIGHT WASHERS The multi-function lever operates the headlight washers when the ignition switch is in the ON position and the headlights are ON. The multi-function lever is located on the left side of the steering column. To use the headlight washers, push the multi-function lever inward (toward the steering column) to the second detent and release it. The headlight washers will spray a timed high-pressure spray of washer fluid onto each headlight lens.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adding Washer Fluid The headlight washer and windshield washer share the same fluid reservoir. The reservoir is located in the front of the engine compartment on the passenger side of the vehicle. Be sure to check the fluid level in the reservoir at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The power tilt/telescoping steering column lever is located below the multi-function lever on the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ADJUSTABLE PEDALS The adjustable pedals system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. This feature allows both the brake and accelerator pedal to move toward or away from the driver to provide improved position with the steering wheel. The switch is located on the front side of the driver’s seat cushion side shield.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. 3 ELECTRONIC SPEED CONTROL When engaged, this device takes over the accelerator operation at speeds greater than 25 mph (40 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate: Push the speed control lever inward (toward the steering column) and release (“ON/OFF”). The indicator light in the lever (and in the instrument cluster on some models) will illuminate to show that the speed control system is ON. To turn the system OFF, push the lever inward (toward the steering column) again and release. At this time, the system and the indicator light will turn off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 speed. To do so, push the lever up and release (RES/ ACCEL), and then remove your foot from the accelerator pedal. To Accelerate For Passing: Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. To Vary the Speed Setting: When the speed control is set, you can increase speed by pushing the lever up and holding (“RES/ACCEL”). When the lever is released, a new set speed will be established.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR PARK ASSIST SYSTEM The Rear Park Assist System is a driver aid that senses for obstacles behind the vehicle. Refer to the Warnings, Cautions, and Notes in this section for system limitations and usage recommendations. The Rear Park Assist System is active when the driver shifts the transmission into the R (Reverse) position, and the parking brake is not applied, and the vehicle speed is less than 10 mph (16 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 WARNING DISPLAY DISTANCES DISPLAY LED 1st LED 2nd LED 3rd LED 4th LED 5th LED 6th LED 7th LED 8th LED OBSTACLE DISTANCE FROM: REAR CORNERS REAR CENTER 59 in. (150 cm) 47 in. (120 cm) 39 in. (100 cm) 31.5 in. (80 cm) 31.5 in. (80 cm) 25.5 in. (65 cm) 25.5 in. (65 cm) 20 in. (50 cm) 20 in. (50 cm) 16 in. (40 cm) 16 in. (40 cm) 6 in. (15 cm) 12 in. (30 cm) NOTE: The Rear Park Assist system will MUTE the radio, if on, when the system is sounding an audio tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Drivers must be careful when backing up even when using the Rear Park Assist System. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 If “Service Park Assist System” appears in the Electronic Vehicle Information Center (EVIC) after making sure the rear bumper is clean please see your authorized dealer. Courtesy/Reading Lights OVERHEAD CONSOLE The overhead console contains courtesy/reading lights, an optional universal garage door opener (HomeLink威), storage for sunglasses, and an optional power sunroof switch. Press the lens to turn on the light.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER (HomeLink姞) The HomeLink威 Universal Transceiver replaces up to three remote controls (hand held transmitters) that operate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button. The Universal Transceiver operates off your vehicle’s battery and charging system; no batteries are needed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Programming HomeLink NOTE: When programming a garage door opener, it is advised to park outside the garage. It is also recommended that you install a new battery in the hand-held transmitter of the device being programmed. This will allow for quicker training and accurate transmission of the radio-frequency signal. The Electronic Vehicle Information Center (EVIC) features a driver-interactive display, which includes HomeLink system messages.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Press and hold the two outer HomeLink buttons. Release the buttons only when the EVIC displays “Channels Cleared” (after 20 seconds); however, do not hold the buttons for longer than 30 seconds. Do not repeat this step if programming a second or third hand-held transmitter to the remaining HomeLink buttons. 3. Simultaneously press and hold the HomeLink button (that you want to train) and the hand-held transmitter button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If your garage door opener fails to respond to the programmed HomeLink威 Universal Transceiver, and your garage door opener is manufactured after 1995, it may have a multiple security code system (rolling code system). Please proceed to Steps 6–8 to complete the programming of a rolling code equipped device (most common garage door openers require this step. 6.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If programming a garage door opener or gate operator, it is advised to unplug the device during the ⬙cycling⬙ process to prevent possible overheating. 3. Continue to press and hold the HomeLink button while you press and release your hand-held transmitter every two seconds until the frequency signal is accepted successfully by HomeLink. The EVIC will display “Channel X Trained” (where X is Channel 1, 2, or 3).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE For questions or comments, contact HomeLink at www.homelink.com or 1-800-355-3515. Security If you sell your vehicle, be sure to erase the frequencies by following the “Erasing HomeLink Buttons” instructions in this section. POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. 3 This device complies with part 15 of FCC rules and with RSS-210 of Industry Canada.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing, press the switch forward and hold for two seconds after the reversal occurs. This allows the sunroof to move towards the closed position. NOTE: Pinch protection is disabled while the switch is pressed. Venting Sunroof - Express Press and release the ⬙V⬙ button, and the sunroof will open to the vent position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Settings (Customer Programmable Features),” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed. NOTE: If desired, the power outlet next to the ash receiver tray (if equipped) can be converted by your authorized dealer to provide power with the ignition switch in the LOCK position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The center console outlet is powered directly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or prevent engine starting. Center Console Power Outlet 125 Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUP HOLDERS Front Seat Cup Holders The cup holders are located in the forward edge of the center console. Push down on the cover as shown to expose the cup holders. Close the cover when the cup holders are no longer needed. Rear Seat Cup Holders The rear seat cup holders are located in the center armrest between the rear seats.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE Console Features The center console contains a large storage bin. The storage bin contains a four-slot coin holder (designed to hold various size coins) and a rubber mat at the bottom of the bin for noise control. The bin is large enough to hold a portable AC/DC converter to power laptops, games, or other electrical equipment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! • Be certain that the seatback is securely locked into position. If the seatback in not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. • The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE LOAD LEVELING SYSTEM The automatic load leveling system will provide a levelriding vehicle under most passenger and cargo loading conditions. A hydraulic pump contained within the shock absorbers raises the rear of the vehicle to the correct height. It takes approximately 1 mile (1.6 km) of driving for the leveling to complete depending on road surface conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel And Controls . . . . . . . . . . . . 134 䡵 Premium Instrument Cluster . . . . . . . . . . . . . . 135 䡵 Instrument Cluster Descriptions . . . . . . . . . . . 136 䡵 Electronic Vehicle Information Center (EVIC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 ▫ Electronic Vehicle Information Center (EVIC) Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 ▫ System Warnings (Customer Information Features) . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Sales Code RAK – AM/FM/Cassette/CD (6-Disc) Radio With Optional Satellite Radio, Hands Free Phone, Video, MP3, And WMA Capabilities . . 159 ▫ Operating Instructions - Radio Mode . . . . . . . 159 ▫ Operating Instructions — Tape Player . . . . . . . 162 ▫ Seek Button . . . . . . . . . . . . . . . . . . . . . . . . . 163 ▫ Fast Forward (FF) . . . . . . . . . . . . . . . . . . . . . 163 ▫ Rewind (RW) . . . . . . . . . . . . . . . . . . . . . . . . 163 ▫ Tape Eject .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) . . . . . . . . . . . . . . . . . . . . 176 ▫ Selecting Satellite Mode In REF, RAQ, And RAK Radios . . . . . . . . . . . . . . . . . . . . . . . . . 177 ▫ Selecting a Channel . . . . . . . . . . . . . . . . . . . . 177 ▫ Storing And Selecting Pre-Set Channels . . . . . . 178 ▫ Using The PTY (Program Type) Button (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . 178 133 ▫ Radio Operation .
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL AND CONTROLS 1 2 3 4 5 — Air Outlet — Instrument Cluster — Hazard Switch — Analog Clock — Electronic Stability Program Off Button* / Traction Control System Off Button* 6 — Glove Box 7 — Radio 8 — Climate Control 9 — Heated Seat Switch* 10 — Power Outlet 11 — Ash Tray* 12 — Storage Compartment* 13 — Ignition Switch 14 — Hood Release 15 — Trunk Release Switch 16 — Headlight Switch * If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 135 PREMIUM INSTRUMENT CLUSTER 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Electronic Speed Control Indicator Light — If Equipped This light will turn on when the electronic speed control is ON. (See page 109 for more information.) 2. Low Fuel Indicator Light This light will turn on and a single chime will sound when the fuel level drops to 1/8 tank. (See page 249 for more information.) 3. Front Fog Light Indicator This light will turn on when the front fog lights are ON.
UNDERSTANDING YOUR INSTRUMENT PANEL 7. Tachometer The red segments indicate the maximum permissible engine revolutions-per-minute (r.p.m. x 1000) for each gear range. Ease up on the accelerator before reaching the red area. 8. Engine Temperature Warning Light This light will turn on and a single chime will sound to warn of an overheated engine condition. When this light turns on, the engine temperature is critically hot. The vehicle should be turned off immediately and serviced as soon as possible.
UNDERSTANDING YOUR INSTRUMENT PANEL during starting, or stays on, or turns on while driving, then have the system inspected at your authorized dealer as soon as possible. (See page 46 for more information.) NOTE: The light may flash momentarily during sharp cornering maneuvers due to a change in fluid level. If so, the vehicle should have service performed and the brake fluid level checked. 12.
UNDERSTANDING YOUR INSTRUMENT PANEL The operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON position. The light should turn on for approximately two seconds and then turn off. The light will remain on if the parking brake is applied or if a brake fault is detected. If the parking brake is not applied and the light remains on, or if the light does not turn on, have the light inspected by an authorized dealer.
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. 15. Trip Odometer Button Press this button to change the display from odometer to either of two trip odometer settings.
UNDERSTANDING YOUR INSTRUMENT PANEL 20. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 21. Electronic Throttle Control (ETC) Light This light will turn on briefly as a bulb check when the ignition switch is turned ON. This light will also turn on while the engine is running if there is a problem with the Electronic Throttle Control system.
UNDERSTANDING YOUR INSTRUMENT PANEL Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster, and an audible chime will be activated when one or more tire pressures is low.
UNDERSTANDING YOUR INSTRUMENT PANEL 24. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD. The OBD system monitors engine and automatic transmission control systems. The light will turn on when the key is in the ON position before engine start. If the light does not come on when turning the key from OFF to ON, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc.
UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) • Vehicle information warning message displays • Tire Pressure Monitor System (if equipped) • Personal Settings (customer programmable features) • Compass display • Outside temperature display • Trip computer functions • UConnect™ hands-free communication system displays (if equipped) • Navigation system screens (if equipped) • Audio mode display Electronic Vehicle Information Center The Electronic Vehicle Information
UNDERSTANDING YOUR INSTRUMENT PANEL Press the FUNCTION SELECT button to accept a selection. The FUNCTION SELECT button also advances the radio to the next preset FUNC- station, changes the side of the tape being TION played (if so equipped), or changes the current SELECT CD track being played (if so equipped) when Button the EVIC is in the Compass/Temp/Audio screen.
UNDERSTANDING YOUR INSTRUMENT PANEL • Memory #1/#2 Profile Recall • Memory System Disabled – Vehicle Not In Park (with a single chime) • Memory System Disabled – Seat Belt Buckled (with a single chime) • Adjustable Pedals Disabled – Vehicle In Reverse (with a single chime) — only available on vehicles equipped with memory seats.
UNDERSTANDING YOUR INSTRUMENT PANEL • Right Front Low Pressure (with a single chime). Refer to information on “Tire Pressure” and “Tire Pressure Monitor” in the “Starting And Operating” section of this manual. • Distance To Empty • Right Rear Low Pressure (with a single chime). Refer to information on “Tire Pressure” and “Tire Pressure Monitor” in the “Starting And Operating” section of this manual. • Elapsed Time • Check TPM System (with a single chime).
UNDERSTANDING YOUR INSTRUMENT PANEL • Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. DTE cannot be reset through the FUNCTION SELECT button.
UNDERSTANDING YOUR INSTRUMENT PANEL Compass Display The compass readings indicate the direction the vehicle is facing. Press and release the compass button to display one of eight comCOM- pass readings and the outside temperature. PASS Button Automatic Compass Calibration This compass is self-calibrating, which eliminates the need to set the compass manually. When the vehicle is new, the compass may appear erratic and the EVIC will display “CAL” until the compass is calibrated.
UNDERSTANDING YOUR INSTRUMENT PANEL 1. Turn the ignition switch ON. 2. Press and hold the compass button for approximately 2 seconds. 3. Press the SCROLL button until “Compass Variance” message and the last variance zone number displays in the EVIC. 4. Press and release FUNCTION SELECT button until the proper variance zone is selected according to the map. 5. Press and release the compass button to exit. Telephone — If Equipped Press and release the MENU button until “Telephone” displays in the EVIC.
UNDERSTANDING YOUR INSTRUMENT PANEL • Call status: Incoming call, connecting, connected, air time in minutes and seconds, call ended, call failed, roaming, and no phone connection. • UConnect Active. The EVIC displays this symbol to indicate that the UConnect™ phone is currently in analog mode. Analog The EVIC displays this symbol to indicate that the UConnect™ phone is currently roaming. • Caller ID phone number display.
UNDERSTANDING YOUR INSTRUMENT PANEL The EVIC displays this symbol to indicate the battery strength of the UConnect™ phone. Battery Strength The EVIC displays this symbol to indicate that a phone connection has been made. Call in Progress The EVIC displays this symbol to indicate that the UConnect™ phone is currently not available. Phone Not Available Navigation — If Equipped Navigation Display Control Press and release the MENU button until Navigation displays in the EVIC.
UNDERSTANDING YOUR INSTRUMENT PANEL System Warnings (Customer Information Features) Press and release the MENU button until “SYSTEM WARNINGS” displays in the EVIC. Then, press the SCROLL button to display anyone of the following choices: • Oil Temperature Shows the actual oil temperature. • Oil Pressure Shows the actual oil pressure. • Tire Pressure Shows the actual tire pressure for each tire (EXCLUDING THE SPARE TIRE).
UNDERSTANDING YOUR INSTRUMENT PANEL “Unlock Doors Automatically on Exit” When ON is selected, all doors will unlock when the vehicle is stopped and the transmission is in the P (Park) or N (Neutral) position and the driver’s door is opened. To make your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears. “Remote Key Unlock” When Driver Door 1st Press is selected, only the driver’s door will unlock on the first press of the remote keyless entry unlock button.
UNDERSTANDING YOUR INSTRUMENT PANEL 155 the FUNCTION SELECT button until “ON” or “OFF” appears. When OFF is selected, the system reverts to the standard intermittent wiper operation. selected. To make your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears. “Automatically Move Seat Back on Exit” — If Equipped This feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL “Tilt Mirrors Down in Reverse” When ON is selected, the outside rearview mirrors will tilt downward when the ignition switch is in the ON position and the transmission is in the R (Reverse) position. The mirrors will move back to their previous position when the transmission is shifted out of R (Reverse). To make your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears.
UNDERSTANDING YOUR INSTRUMENT PANEL “Display Units of Measure in” The EVIC, odometer, and navigation system (if equipped) can be changed between English and Metric units of measure. To make your selection, press and release the FUNCTION SELECT button until “US” or “METRIC” appears. 157 SETTING THE ANALOG CLOCK To set the analog clock at the top center of the instrument panel, press and hold the button until the setting is correct.
UNDERSTANDING YOUR INSTRUMENT PANEL RADIO GENERAL INFORMATION Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile operation and natural phenomena, which might lead you to believe your sound system is malfunctioning.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAK – AM/FM/CASSETTE/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, VIDEO, MP3, and WMA CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate. 159 Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON.
UNDERSTANDING YOUR INSTRUMENT PANEL Press the right side of the button to seek up and the left side to seek down. The radio will remained tuned to the new station until you make another selection. Holding the button and will bypass stations without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL 161 AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Press the rotary TUNE control again to exit setting tone, balance, and fade. Setting the Tone, Balance, and Fade Press the rotary TUNE control and BASS will display. Turn the TUNE control to the right or left to increase or decrease the Bass tones. RND/PTY Button (Radio Mode) Pressing this button once will turn on the PTY mode for 5 seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL Soft Rock Top 40 Country Oldies Soft Nostalgia Jazz Classical Rhythm and Blues Soft Rhythm and Blues Foreign Language Religious Music Religious Talk Personality Public College Unassigned Weather Soft_Rock Top_40 Country Oldies Soft Nostalgia Jazz Classical Rhythm_and_Blues Soft_R_&_B Foreign_Language Religious_Music Religious_Talk Personality Public College Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next freq
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Button Press the SEEK button up for the next selection on the tape and down to return to the beginning of the current selection. Press the SEEK button up or down to move the track number to skip forward or backward 1 to 6 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc. Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing.
UNDERSTANDING YOUR INSTRUMENT PANEL Noise Reduction The Dolby Noise Reduction System* is on whenever the tape player is on, but may be switched off. To turn off the Dolby Noise reduction System: Press Preset 1 after you insert the tape. The NR light in the display will go off when the Dolby System is off. * ”Dolby” noise reduction is manufactured under license from Dolby Laboratories Licensing Corporation. Dolby and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (CD MODE for CD Audio Play) Press the Scan button to scan through each track on the CD currently playing. LOAD/EJECT Button (CD Mode for CD Audio Play) LOAD/EJECT - Load Press the LOAD/EJT button and the pushbutton with the corresponding number where the CD is being loaded. The radio will display PLEASE WAIT and prompt when to INSERT DISC. After the radio displays ⬙INSERT DISC,⬙ insert the CD into the player.
UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF (CD MODE for CD Audio Play) Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner. TUNE Control (CD MODE for CD Audio Play) Pressing the TUNE control allows the setting of the Tone, Fade, and Balance. See Radio Mode. AM/FM Button (CD MODE for CD Audio Play) Switches the Radio to the Radio mode.
UNDERSTANDING YOUR INSTRUMENT PANEL files properly and may be unable to play the file normally. UDF and Apple HFS formats are not supported. The radio uses the following limits for file systems: • Maximum number of directory levels: 15 • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙.⬙ and a 3-character extension) • Level 2: 31 (including a separator ⬙.
UNDERSTANDING YOUR INSTRUMENT PANEL ID3 Tag information for artist, song title, and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported. Playback of MP3 and WMA Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL The radio display will show ⬙LOADING DISC⬙ when the disc is loading. LOAD/EJT - Eject Press the LOAD/EJT button and the pushbutton with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded.
UNDERSTANDING YOUR INSTRUMENT PANEL RND/PTY Button (CD Mode for MP3 Play) Pressing this button plays files randomly. SET/DIR Button (CD Mode for MP3 Play) Press the SET/DIR Button to display folders, when playing an MP3 discs that have a file/folder structure. Turn the TUNE control to display available folders or move through available folders. Press the TUNE control to select a folder.
UNDERSTANDING YOUR INSTRUMENT PANEL screen to provide maps, turn identification, selection menus and instructions for selecting a variety of destinations and routes, AM/FM stereo radio and six-disc CD changer with MP3 capability. 171 1. At the Main Menu screen, highlight “Clock Setup” and press ENTER OR press and hold for 3 seconds the TIME button on the unit’s faceplate. The Clock Setup screen appears. Mapping information for navigation is supplied on a DVD that is loaded into the unit.
UNDERSTANDING YOUR INSTRUMENT PANEL 4. To turn daylight savings on or off, select “Daylight Savings” and press ENTER. Select “On” or “Off” and press ENTER. 5. Select DONE to exit from the clock setting mode. Press ENTER to save your changes. If you press CANCEL or NAV then your changes will not be saved. User Defined Clock If you wish to set the clock to a time different than the system clock, you can manually adjust the time by choosing the “User Defined Clock” option. 1.
UNDERSTANDING YOUR INSTRUMENT PANEL 4. To increase the clock by minutes, make sure “MIN +” is highlighted and press ENTER. Press ENTER again to increase the clock by another minute. 5. To decrease the clock by minutes, use the Select Encoder to highlight the “-“ sign. Press ENTER. Press ENTER again to decrease the clock by another minute. 6. Select “DONE” to exit from the clock setting mode. Press ENTER to save your changes. If you press CANCEL or NAV then your changes will not be saved.
UNDERSTANDING YOUR INSTRUMENT PANEL 3. To switch the clock to the small clock, quickly press TIME again. VIDEO ENTERTAINMENT SYSTEM (SALES CODE XRV) — IF EQUIPPED The optional VES™ (Video Entertainment System) consists of a DVD player and LCD (liquid crystal display) screen, a battery-powered remote control, and two headsets. The system is located in the center console storage bin under the armrest lid. Refer to your VES™ User’s Manual for detailed operating instructions. 4.
UNDERSTANDING YOUR INSTRUMENT PANEL 175 4 Raising The DVD Screen Remote Control Location Kicker Mobile Surround (KMS1) The VES for this vehicle comes equipped with Kicker Mobile Surround (KMS1). This feature offers the ultimate movie experience by providing surround sound uniquely equalized for the interior space of your vehicle. The KMS1 activates whenever a DVD is in the VES player, and the radio mode is set to VES, and the video screen is powered up.
UNDERSTANDING YOUR INSTRUMENT PANEL video screen is stowed away, or the radio is set to a mode other than VES, or if you are using the Aux jacks on the VES. Your vehicle is equipped with a state of the art digital audio amplifier that decodes stereo sound inputs into 5.1 formatted surround sound. When in surround sound mode, the KMS1 automatically sets balance and fade to provide the optimal surround experience.
UNDERSTANDING YOUR INSTRUMENT PANEL ESN/SID mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. ESN/SID Access With RAQ and RAK Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and TIME buttons simultaneously for 3 seconds. All twelve ESN/SID numbers will display.
UNDERSTANDING YOUR INSTRUMENT PANEL and the bottom of the button to search down. Holding the TUNE button causes the radio to bypass channels until the button is released. Press and release the SCAN button (if equipped) to automatically change channels every 7 seconds. The radio will pause on each channel for 7 seconds before moving on to the next channel. The word ⬙SCAN⬙ will appear in the display between each channel change. Press the SCAN button a second time to stop the search.
UNDERSTANDING YOUR INSTRUMENT PANEL Satellite Antenna To ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items should be placed as far forward as possible. Do not place items directly on or above the antenna.
UNDERSTANDING YOUR INSTRUMENT PANEL VOLUME Button The VOLUME button controls the sound level of the sound system. Press the top of the VOLUME button to increase the sound level. Press the bottom of the VOLUME button to decrease the sound level. Press the AUDIO MODE button to select the Compass/Temp/Audio screen.
UNDERSTANDING YOUR INSTRUMENT PANEL Tape Player Operation Press the top of the SCROLL button once to listen to the next track on the cassette. Press the bottom of the SCROLL button once either to listen to the beginning of the current track or to listen to the beginning of the previous track if it is within 5 seconds after the current track begins to play.
UNDERSTANDING YOUR INSTRUMENT PANEL 5. A loose tape should be corrected before use. To rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the required directions. CD/DVD DISC MAINTENANCE To keep the CD/DVD discs in good condition, take the following precautions: Maintain your cassette tape player. The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played.
UNDERSTANDING YOUR INSTRUMENT PANEL RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL The controls on the climate control provide the system with operator input. The dual sun-sensor monitors sun load coming through the windshield. The infrared sensor independently measures the surface temperature of the driver and passenger. Other sensors take account of vehicle-speed, A/C pressure, outside temperature, and engine cooling temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL The system will automatically control recirculation. However, pressing the Recirculation Control button will temporarily put the system in recirculation mode (ten minutes). This can be used when outside conditions such as smoke, odors, dust, or high humidity are present. Activating recirculation will cause the LED in the control button to illuminate. After ten minutes, the system will return to normal AUTO mode function and the LED will turn off.
UNDERSTANDING YOUR INSTRUMENT PANEL
UNDERSTANDING YOUR INSTRUMENT PANEL The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Control knob (on the right) to one of the following positions. • Defrost Air is directed to the windshield through the outlets at the base of the windshield. Air is also directed to the front door windows through the side window demister grilles. • Defrost/Floor Air flows through the front and rear floor outlets and the outlets at the base of the windshield.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: To control the air conditioning manually, the mode selector must be moved out of the AUTO position. • Recirculation Control This button can be used to block out smoke, odors, dust, high humidity, or if rapid cooling is desired. The recirculation mode should only be used temporarily. An LED in the button illuminates when the recirculation mode is active. You may use this feature separately. NOTE: Extended use of recirculation may cause the windows to fog.
UNDERSTANDING YOUR INSTRUMENT PANEL system lubrication to minimize the possibility of compressor damage when the system is started again. Window Fogging Interior fogging on the windshield can be quickly removed by turning the mode selector to Defrost. The Defrost/Floor mode can be used to maintain a clear windshield and provide sufficient heating. If side window fogging becomes a problem increase blower speed. Vehicle windows tend to fog on the inside in mild but rainy or humid weather.
UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions for Various Weather Conditions
UNDERSTANDING YOUR INSTRUMENT PANEL REAR WINDOW FEATURES Electric Rear Window Defroster The electric Rear Window Defroster Control is located on the climate control. Press this button to turn on the rear window defroster and the heated side mirrors (if equipped). An LED in the button will illuminate when the rear window defroster is ON.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 196 ▫ 5 Speed Automatic Transmission . . . . . . . . . . 203 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 197 䡵 AutoStick威 . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 197 ▫ AutoStick威 Operation . . . . . . . . . . . . . . . . . . 207 ▫ Extremely Cold Weather (Below ⫺20°F Or ⫺29°C) . . . . . . . . . . . . . . . .
STARTING AND OPERATING 䡵 Electronic Brake Control System . . . . . . . . . . . 214 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . . 232 ▫ ABS (Anti-Lock Brake System) . . . . . . . . . . . . 214 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . . 233 ▫ TCS (Traction Control System) . . . . . . . . . . . . 215 ▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . . 233 ▫ BAS (Brake Assist System) . . . . . . . . . . . . . . . 215 ▫ Replacement Tires . . . . . . .
STARTING AND OPERATING 195 ▫ 6.1L Engine . . . . . . . . . . . . . . . . . . . . . . . . . 246 ▫ Vehicle Certification Label . . . . . . . . . . . . . . . 252 ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . . 246 ▫ Gross Vehicle Weight Rating (GVWR) . . . . . . . 252 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . . 247 ▫ Gross Axle Weight Rating (GAWR) . . . . . . . . . 252 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . . 247 ▫ Overloading . . . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! • Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition.
STARTING AND OPERATING Automatic Transmission The gear selector must be in the NEUTRAL or PARK position before you can start the engine. Apply the brakes before shifting into any driving gear. Normal Starting Normal Starting of either a cold or a warm engine is obtained without pumping or depressing the accelerator pedal. Turn the key to the “START” position and release when the engine starts. If the engine has not started within 3 seconds, slightly depress the accelerator pedal while continuing to crank.
STARTING AND OPERATING WARNING! • Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt AC electrical outlet with a grounded, three-wire extension cord. The engine block heater cord is routed under the hood on the driver side of the vehicle. It has a removable cap that is located on the driver side of the Integrated Power Module. WARNING! Remember to disconnect the cord before driving.
STARTING AND OPERATING WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
STARTING AND OPERATING The selector lever is automatically locked while in the P (Park) position. To move the selector lever out of the P (Park) position, the brake pedal must be firmly depressed before the shift lock will release. Shift the selector lever to the desired position only when the engine is idling normally and the brake pedal is applied. Do not release the brake until ready to drive. The vehicle may otherwise accelerate quickly when the selector lever is in D (Drive) or R (Reverse) position.
STARTING AND OPERATING Brake/Transmission Shift Interlock System This vehicle is equipped with a brake transmission shift interlock system (BTSI) that holds the selector lever in the P (Park) position when the ignition switch is in the LOCK position. To move the gear selector lever out of the P (Park) position, the ignition switch must be turned to the ON position, and the brake pedal must be depressed.
STARTING AND OPERATING 5 Speed Automatic Transmission Shifting from D (Drive) to P (Park) or R (Reverse) (or from P or R to D) should be done only after the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake when moving the selector lever between these gears. 203 Never use P (Park) while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range.
STARTING AND OPERATING The following indicators should be used to ensure that you have engaged the selector lever into the P (Park) position: • When shifting into P (Park) move the lever all the way forward until it stops, and is fully seated. • Look at the shift indicator display on the instrument panel to ensure it is in the P (Park) position. (Neutral) position while driving except to coast when the vehicle is in danger of skidding (e.g., on icy roads). The engine may be started in this range.
STARTING AND OPERATING D (Drive) This range should be used for most city and highway driving. It provides the smoothest upshifts and downshifts and best fuel economy. The transmission automatically upshifts through fifth gear. The D (Drive) position provides optimum driving characteristics under all normal operating conditions.
STARTING AND OPERATING WARNING! On slippery road surfaces, never downshift in order to obtain braking action. This could result in drive wheel slip and reduced vehicle control. Your vehicle’s ABS will not prevent this type of loss of control. You could lose control of your vehicle and have an accident. Delayed Shifts in Cold Temperatures During cold temperature operation, you may notice delayed upshifts depending on engine and transmission temperature as well as vehicle speed.
STARTING AND OPERATING NOTE: Even if the transmission can be reset, we recommend that you visit a dealer at your earliest possible convenience. Your dealer has diagnostic equipment to determine if the problem could recur. Have the transmission checked at your authorized dealer as soon as possible. If the problem has been momentary, the transmission can be reset to regain all forward gears.
STARTING AND OPERATING • An UPSHIFT message will appear in the Electronic Vehicle Information Center (EVIC) portion of the instrument cluster when using Autostick威. This message appears in order to alert the driver to upshift to the next gear. The UPSHIFT message will display while operating the vehicle at higher engine revolutions-perminute (RPM). Autostick姞 General Information You can shift in or out of the Autostick威 mode at any time without taking your foot off the accelerator pedal.
STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the rear wheels to pull erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the rear (driving) wheels. WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the rear wheels. You could lose control of the vehicle and possibly have an accident.
STARTING AND OPERATING PARKING BRAKE The parking brake should always be applied when the driver is not in the vehicle. WARNING! The foot operated parking brake is positioned below the lower left corner of the instrument panel. To apply the parking brake, push the parking brake pedal down and then remove your foot from the pedal. To release the parking brake, push down on the parking brake pedal and then release.
STARTING AND OPERATING NOTE: This light only shows that the parking brake is applied. It does not show the degree of brake application. WARNING! • Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle.
STARTING AND OPERATING When the vehicle is driven over 7 mph (11 km/h), you may also hear a slight clicking sound as well as some related motor noises. These noises are the system performing its self check cycle to ensure that the ABS system is working properly. This self check occurs each time the vehicle is started and accelerated past 7 mph (11 km/h).
STARTING AND OPERATING All vehicle wheels and tires must be the same size and type and tires must be properly inflated to produce accurate signals for the computer. Anti-Lock Brake Light The ABS light monitors the Anti-Lock Brake System. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds.
STARTING AND OPERATING WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur.
STARTING AND OPERATING WARNING! The ABS (Anti-Lock Brake System) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. The ABS cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING WARNING! The BAS (Brake Assist System) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. The BAS cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING WARNING! The ESP (Electronic Stability Program) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. The ESP cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING Full Off This mode is intended for off-highway or off-road use only and should not be used on any public roadways. In this mode, all TCS and ESP stability features are turned off. To enter the “Full Off” mode, depress and hold the “ESP OFF” button for 5 seconds while the vehicle is stopped with the engine running. After 5 seconds, a chime will sound, the ⬙ESP/TCS Indicator Light⬙ will illuminate, and the ⬙ESP OFF⬙ message will display in the vehicle odometer.
STARTING AND OPERATING WARNING! With the ESP switched off, the enhanced vehicle stability offered by ESP is unavailable. In an emergency evasive maneuver, the ESP system will not engage to assist in maintaining stability. The “Full Off” ESP mode is intended for off-highway or offroad only. Synchronizing ESP The malfunction indicator light for the ESP is combined with BAS indicator.
STARTING AND OPERATING NOTE: • ⬙The ⬙ESP/TCS Indicator Light⬙ and the ⬙ESP/BAS Malfunction Indicator Light⬙ will turn on momentarily each time the ignition switch is turned ON. • Each time the ignition is turned ON, the ESP System will be ON even if it was turned off previously. • The ESP Control System will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESP becomes inactive following the maneuver that caused the ESP activation.
STARTING AND OPERATING 221 NOTE: • P (Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • Temporary Spare tires are high-pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation. Example: T145/80D18 103M.
STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING 223 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (i.e. tire pressure, vehicle loading, road conditions, and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure 225 Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar.
STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information” placard and in the “Vehicle Loading” section of this manual.
STARTING AND OPERATING 227 manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. illustration purposes only and may not be accurate for the seating and load carry capacity of your vehicle. NOTE: The following table shows examples on how to calculate total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and number and size of occupants.
STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 229 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation, also increases tire rolling resistance and results in higher fuel consumption. 3. Ride Comfort and Vehicle Stability— Proper tire inflation contributes to a comfortable ride. Over inflation produces a jarring and uncomfortable ride.
STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.” Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1 km) after a 3 hour period.
STARTING AND OPERATING WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Radial-Ply Tires Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. 233 Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure.
STARTING AND OPERATING Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manufacturer strongly recommends that you use tires equivalent to the originals in size, quality and performance when replacement is needed (refer to the paragraph on “Tread Wear Indicators”). Refer to the “Tire and Loading Information” placard for the size designation of your tire.
STARTING AND OPERATING CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. Alignment And Balance Poor suspension alignment may result in: • Fast tire wear. • Uneven tire wear, such as feathering and one-sided wear. • Vehicle pull to right or left. 235 Tires may also cause the vehicle to pull to the left or right. Alignment will not correct this condition. See your dealer for proper diagnosis.
STARTING AND OPERATING CAUTION! To avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious damage. Stop the vehicle immediately if noise occurs that could indicate chain breakage. Remove the damaged parts of the chain before further use.
STARTING AND OPERATING Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear patterns.
STARTING AND OPERATING Tire Rotation — Standard Tires The suggested rotation method is the “side-to-side” as shown in the following diagram. Tire Rotation — All Season Tires The suggested rotation method for vehicles equipped with all season tires is the “forward-cross” as shown in the following diagram.
STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM (TPMS) — IF EQUIPPED • The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. • The tire pressure will vary with temperature by about 1 psi (6.9 kPa) for every 12°F (6.5°C). This means that when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure.
STARTING AND OPERATING − For example, your vehicle may have a recommended cold (parked for more than 3 hours) placard pressure of 30 psi (207 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 27 psi (186 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressure to approximately 23 psi (157 kPa). This tire pressure is sufficiently low enough to turn ON the Tire Pressure Monitoring Telltale light.
STARTING AND OPERATING NOTE: • The TPMS is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. • Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
STARTING AND OPERATING receives the updated tire pressures, the system will automatically update and the Tire Pressure Monitoring Telltale Light will turn off. The vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. Low pressure in the spare tire will not cause the Tire Pressure Monitoring Telltale Light to illuminate or the chime to sound.
STARTING AND OPERATING The TPMS consists of the following components: • Receiver Module • 4 Tire Pressure Monitoring Sensors • 3 Trigger Modules (mounted in three of the four wheel-wells) • Various Tire Pressure Monitoring System Messages, which display in the Electronic Vehicle Information Center (EVIC) • Tire Pressure Monitoring Telltale Light Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster and an audible chime will soun
STARTING AND OPERATING NOTE: • You can change the pressure units to display in PSI, kPA, or BAR. Refer to “Language,” under “Personal Settings (Customer Programmable Features),” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual for details. • The compact spare tire (if so equipped) does not have a tire pressure monitoring sensor. Therefore, the TPMS will not monitor the pressure in the compact spare tire.
STARTING AND OPERATING Center (EVIC) will display a ⬙CHECK TPM SYSTEM⬙ message for 3 seconds when a system fault is detected. In the event that a fault occurs because the system did not receive a pressure value from one or more Tire Pressure Monitoring Sensors, the EVIC will display the ⬙CHECK TPM SYSTEM⬙ message and then display dashes (- -) in place of the pressure value to indicate which sensor is not being received. 245 NOTE: You can change the pressure units to display in PSI, kPA, or BAR.
STARTING AND OPERATING The tire pressure sensors are covered under one of the following licenses: United States . . . . . . . . . . . . . . . . . . . . . KR5S120123 Canada . . . . . . . . . . . . . . . . . . . . . . . . 2671-S120123 FUEL REQUIREMENTS 6.1L Engine The 6.1L engine is designed to meet all emissions regulations and provide excellent fuel economy and performance when using high-quality premium unleaded gasoline with an octane rating of 91 or higher.
STARTING AND OPERATING Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as 10% ethanol, MTBE, and ETBE. Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle. CAUTION! DO NOT use gasolines containing Methanol or E85 Ethanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components.
STARTING AND OPERATING normal conditions and they would result in additional cost. Therefore, you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance, or damage the emission control system. • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat.
STARTING AND OPERATING more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle. • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. 249 ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel filler door on the left side of the vehicle.
STARTING AND OPERATING NOTE: When removing the fuel filler cap, lay the cap tether in the hook, located on the fuel filler cap door reinforcement. Gas Cap Tether Hook CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap could let impurities into the fuel system. • A poorly fitting gas cap may cause the Malfunction Indicator Light to turn on.
STARTING AND OPERATING WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel to the vehicle when the engine is running. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. NOTE: • Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is tightened properly.
STARTING AND OPERATING VEHICLE LOADING The load carrying capacity of your vehicle is shown on the “Vehicle Certification Label.” This information should be used for passenger and luggage loading as indicated. If the seatbacks are folded for carrying cargo, do not exceed the specified GVWR and GAWR. Vehicle Certification Label Your vehicle has a certification label attached to the rear of the driver’s door.
STARTING AND OPERATING Overloading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and front and rear GAWR. The best way to figure out the total weight of your vehicle is to weigh it when it is fully loaded and ready for operation. Weigh it on a commercial scale to insure that it is not over the GVWR. Figure out the weight on the front and rear of the vehicle separately.
STARTING AND OPERATING EXAMPLE ONLY Empty Weight Load (Including driver, passengers, and cargo) Total GAWR Front Rear Axle Axle 2054 lbs 1805 lbs (932 kg) (819 kg ) 271 lbs 579 lbs (123 kg) (263 kg) 2325 lbs 2384 lbs (1055 kg) (1081 kg) 2546 lbs 2708 lbs (1155 kg) (1228 kg) NOTE: Refer to the “Vehicle Certification Label” attached to the rear of the driver’s door for your vehicle’s GVWR and GAWRs. This table is only an example. TRAILER TOWING Trailer towing with this vehicle is not recommended.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 256 ▫ Without The Ignition Key . . . . . . . . . . . . . . . 266 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 256 ▫ Towing This Vehicle Behind Another Vehicle (Flat Towing With All Four Wheels On The Ground) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266 䡵 TIREFIT Tire Repair . . . . . . . . . . . . . . . . . . . . 257 䡵 Jump-Starting Procedures . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The hazard flasher switch is located in the center of the instrument panel between the center air outlets. This is an emergency warning system and it should not be used when the vehicle is in motion. Use it when your vehicle is disabled and it is creating a safety hazard for other motorists. When you must leave the vehicle to seek assistance, the Hazard Warning Flashers will continue to operate even though the ignition switch is OFF.
WHAT TO DO IN EMERGENCIES NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat. You can also turn the Temperature control to maximum heat, the Mode control to floor, and the fan control to HI. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system.
WHAT TO DO IN EMERGENCIES The TIREFIT system is located under an access panel in the trunk. TIREFIT contents 1. Air pump hose TIREFIT Location 2. Power plug and cable 3. Air pump switch 4. Pressure gauge 5. TIREFIT sealant bottle 6.
WHAT TO DO IN EMERGENCIES WARNING! • Do not attempt to repair a tire on the side of the vehicle 259 Sealing tire with TIREFIT 1. Turn on the hazard warning flashers. close to traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or repairing a tire. • Cuts or punctures larger than approximately 0.16 in. (4 mm), tire damage caused by driving with extremely low tire pressure or on a flat tire, or a damaged wheel can pose a hazard while driving.
WHAT TO DO IN EMERGENCIES 5. Unscrew the valve cap from the valve on the deflated tire. 6. Screw the fitting at the end of TIREFIT sealant hose (6) coming from the sealant bottle (5) onto the tire valve. 12. Release the parking brake and drive the vehicle back and forth approximately 30 feet (9.1 m) to distribute the sealant more evenly within the tire. 13. Turn on the hazard warning flashers. 7. Insert the power plug (2) into the power point on the instrument panel. 14.
WHAT TO DO IN EMERGENCIES 19. With a tire pressure of no less than 26 psi (1.8 bar) press the air pump switch (3) to 0 (OFF) and turn off the engine. Then, disconnect the TIREFIT system from the tire and place it back in the vehicle. 20. Release the parking brake and drive the vehicle for approximately 10 minutes to ensure optimum distribution of the tire sealant within the tire. 21. Turn on the hazard warning flashers. 22.
WHAT TO DO IN EMERGENCIES • Do not operate the electric air pump for more than eight minutes to avoid overheating. The air pump may be used again once it has cooled down. • Replace the TIREFIT sealant bottle (5) once every four years to assure optimum operation of the system. • If TIREFIT is liquid, clean water and a damp cloth will remove the material from the vehicle or tire and wheel components. Once TIREFIT sealing material has dried, it can easily be peeled off and properly discarded.
WHAT TO DO IN EMERGENCIES NOTE: The battery is stored under an access cover in the trunk. Remote battery terminals are located in the engine compartment for jump-starting. 1. Wear eye protection and remove any metal jewelry such as watchbands or bracelets that might make an inadvertent electrical contact. 2. When boost is provided by a battery in another vehicle, park that vehicle within booster cable reach, but do not allow the vehicles to touch one another. 5.
WHAT TO DO IN EMERGENCIES WARNING! • You should not try to start your vehicle by pushing or towing. • Do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. • During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump-starting because the battery could rupture or explode.
WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand, or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth between Reverse and Drive. Usually the least accelerator pedal pressure to maintain the rocking motion without spinning the wheels is most effective. NOTE: Turn off the Electronic Stability Program (ESP) before rocking the vehicle.
WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE WITHOUT THE IGNITION KEY Special care must be taken when the vehicle is towed with the ignition in the LOCK position. The only approved method of towing without the ignition key is with a flat bed truck. Proper towing equipment is necessary to prevent damage to the vehicle.
WHAT TO DO IN EMERGENCIES CAUTION! • Do not attempt to tow this vehicle from the front with sling type towing equipment. Damage to the front fascia will result. • If the transmission is not operative, or if the vehicle is to be towed more than 30 miles (48 km), then the only approved method of towing is with a flat bed truck. Damage to the transmission may result. • Do not tow the vehicle from the rear. Damage to the rear sheet metal, and fascia will occur.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 6.1L Engine Compartment . . . . . . . . . . . . . . . 271 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . . 279 䡵 Onboard Diagnostic System — OBD II . . . . . . 272 ▫ Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . 279 ▫ Loose Fuel Filler Cap . . . . . . . . . . . . . . . . . . 272 ▫ Catalytic Converter . . . . . . . . . . . . . . . . . . . . 279 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Windshield Washers/Headlight Washers . . . . . 285 ▫ Fuses (Rear Power Distribution Center) . . . . . . 302 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . . 286 䡵 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . . 306 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . . . 287 䡵 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . . 307 ▫ Hoses And Vacuum/Vapor Harnesses . . . . . . . 291 䡵 Bulb Replacement . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 271 6.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE A loose, improperly installed, or damaged fuel filler cap may also turn on the Malfunction Indicator Light (MIL). EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. 273 Your vehicle has a simple ignition key actuated test, which you can use prior to going to the test station.
MAINTAINING YOUR VEHICLE b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station. If your OBD system is not ready, you should see your authorized dealer or repair facility.
MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle.
MAINTAINING YOUR VEHICLE • Day or night temperatures are below 32°F (0°C). • Stop and Go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C). • Trailer towing. Engine Oil Dipstick CAUTION! • Taxi, Police, or delivery service (commercial service). • Off-Road or desert operation.
MAINTAINING YOUR VEHICLE 277 NOTE: Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or 6 months, whichever comes first. Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends full synthetic engine oils that meet the American Petroleum Institute (API) categories of SM or SM/CF, and meet the requirements of DaimlerChrysler Material Standard MS-10725.
MAINTAINING YOUR VEHICLE Disposing of Used Engine Oil and Oil Filters Care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, indiscriminately discarded, can present a problem to the environment. Contact your dealer, service station, or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced at every engine oil change.
MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter For normal driving conditions, inspect and replace the engine air cleaner filter at the intervals shown on Schedule “A.” For vehicles driven frequently in dusty or under severe conditions, inspect and replace the engine air cleaner filter at the intervals shown on Schedule “B.” WARNING! The air induction system (air cleaner, hoses, etc) can provide a measure of protection in the case of engine backfire.
MAINTAINING YOUR VEHICLE CAUTION! WARNING! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle.
MAINTAINING YOUR VEHICLE 281 • Do not try to start engine by pushing or towing the vehicle. • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idling or malfunctioning operating conditions. Maintenance-Free Battery The top of the MAINTENANCE-FREE battery is permanently sealed. You will never have to add water, nor is periodic maintenance required.
MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin, or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information book for further warranty information. • The air conditioning system contains refrigerant under high pressure.
MAINTAINING YOUR VEHICLE Refer to the “Maintenance Schedule” in this manual for the recommended air conditioning filter replacement intervals. Power Steering — Fluid Check Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through a certified DaimlerChrysler Dealership.
MAINTAINING YOUR VEHICLE The external lock cylinders should be lubricated twice a year, preferably in the fall and spring. Apply a small amount of a high quality lubricant such as Mopar威 Lock Cylinder Lubricant or equivalent directly into the lock cylinder. Windshield Wiper Blades The rubber edges of the wiper blades and the windshield should be cleaned periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accumulations of salt or road film.
MAINTAINING YOUR VEHICLE Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
MAINTAINING YOUR VEHICLE Cooling System WARNING! 287 accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position. • You or others can be badly burned by hot coolant or steam from your radiator.
MAINTAINING YOUR VEHICLE system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of old antifreeze solution. Selection of Coolant Use only the manufacturer’s recommended coolant. Refer to “Fluids, Lubricants, and Genuine Parts” for the correct coolant type. CAUTION! • Mixing of coolants other than specified HOAT engine coolants, may result in engine damage and may decrease corrosion protection.
MAINTAINING YOUR VEHICLE Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Years or 100,000 miles (160 000 km) before replacement. To prevent reducing this extended maintenance period, it is important that you use the same coolant throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) coolant.
MAINTAINING YOUR VEHICLE WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
MAINTAINING YOUR VEHICLE humidity accumulating on the radiator and being vaporized when the thermostat opens, allowing hot coolant to enter the radiator. If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check coolant freeze point in the radiator and in the coolant recovery bottle.
MAINTAINING YOUR VEHICLE Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present. Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Suggested service intervals can be found in the “Maintenance Schedule” in this manual.
MAINTAINING YOUR VEHICLE 293 Insure nylon tubing in these areas has not melted or collapsed. WARNING! Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present. Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately.
MAINTAINING YOUR VEHICLE brakes, fluid level can be expected to fall as the brake pads wear. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” for the correct fluid type. CAUTION! Do not allow petroleum base fluid to contaminate the brake fluid, all brake seal components could be damaged causing partial or complete brake failure.
MAINTAINING YOUR VEHICLE CAUTION! • Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Genuine Parts” for the correct fluid type.
MAINTAINING YOUR VEHICLE Appearance Care and Protection from Corrosion • Stone and gravel impact. Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice, and chemicals that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
MAINTAINING YOUR VEHICLE CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open. • If you detect any stone chips or scratches in the paint, touch them up immediately.
MAINTAINING YOUR VEHICLE Interior Care Use Mopar威 Fabric Cleaner or equivalent to clean fabric upholstery and Mopar威 Carpet Cleaner for carpeting. Interior Trim should be cleaned starting with a damp cloth, or Mopar威 Satin Select. Do not use harsh cleaners or Armorall. Use Mopar威 Total Clean to clean vinyl upholstery. Mopar威 Total Clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth.
MAINTAINING YOUR VEHICLE cleaner. Use caution when cleaning the inside rear window equipped with electric defrosters or the right rear quarter window equipped with the radio antenna. Do not use scrapers or other sharp instruments, which may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror.
MAINTAINING YOUR VEHICLE FUSES (POWER DISTRIBUTION CENTERS) Cavity Fuses (Front Power Distribution Center) A power distribution center is located in the engine compartment. This center contains fuses and relays.
MAINTAINING YOUR VEHICLE Cavity 10 11 12 13 14 15 16 17 18 Cartridge Fuse — Mini Fuse 5 Amp Orange 25 Amp Clear Description Powertrain Control Module (PCM)/Starter — Auto Shutdown/ Powertrain Control Module (PCM) — — — — — — — 25 Amp Powertrain Control Clear Module (PCM) — 20 Amp Injectors, Ignition Coils yellow — — — 30 Amp — Anti-lock Brakes System Pink (ABS) Valves/ Powertrain Control Module (PCM) 30 Amp — Windshield Wiper/ Pink Washer Cavity 19 20 21 22 23 24 25 26 27 Cartridge Fuse 50 Amp Re
MAINTAINING YOUR VEHICLE CAUTION! • When installing the Power Distribution Center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Power Distribution Center, and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
MAINTAINING YOUR VEHICLE Cavity 6 Cartridge Fuse 60 Amp Yellow 40 Amp Green — 40 Amp Green 40 Amp Green — 7 — 8 — 9 — 10 11 * — — 1 2 3 4 5 Mini Fuse Description Cavity — Ignition Off Draw (IOD) — Battery 12 * 13 * 14 Cartridge Fuse — — — — — — Battery 15 16 17 — — — 18 — 19 — 20 21 22 23 24 25 — — — — — — — Heated Seats - if equipped 20 Amp Fuel Pump Yellow 20 Amp Amplifier — Subwoofer Yellow 15 Amp Ignition Switch/Airbag Blue Control Module (ACM) 20 Amp Console Power Outle
MAINTAINING YOUR VEHICLE Cavity 26 27 Cartridge Fuse — — 28 — 29 — 30 — 31 32 33 34 — — — — Mini Fuse — 10 Amp Red 10 Amp Red 5 Amp Orange Description — Airbag/Airbag Control Module (ACM) Curtain Airbag - if equipped Anti-lock Brakes Module/Cluster/Front Control Module (FCM)/ Powertrain Control Module (PCM)/Sentry Key Remote Keyless Entry/Stop Lights 10 Amp Door Modules/Power Red Mirrors - if equipped/ Steering Control Module — — — — — — — — Cavity 35 Cartridge Fuse — 36 — 37 — 38
MAINTAINING YOUR VEHICLE Cavity 39 40 41 42 43 44 Cartridge Fuse — Mini Fuse 10 Amp Red 10 Amp Red Description Heated Mirrors - if equipped — Heated Seats - if equipped/Inside Rearview Mirror — 10 Amp AC Heater Control/Park Red Assist - if equipped/Tire Pressure Monitoring - if equipped 30 Amp — Front Blower Motor Pink 30 Amp — Amplifier - if equipped/ Pink Antenna/Rear Defrost 20 Amp — Amplifier - if equipped/ Blue Front Control Module (FCM)/Sunroof - if equipped 305 * Cavities 11, 12, and 13 con
MAINTAINING YOUR VEHICLE CAUTION! • When installing the Power Distribution Center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Power Distribution Center, and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
MAINTAINING YOUR VEHICLE REPLACEMENT BULBS LIGHT BULBS — Interior Bulb Number Rear Courtesy/Reading Lights. . . . . . . . . . . . . . W5W Rear Compartment (Trunk) Light . . . . . . . . . . . . . 579 Overhead Console Reading Lights. . . . . . . . . . . . . 578 Visor Vanity Lights . . . . . . . . . . . . . . . . . . . . . A6220 Glove Box Light . . . . . . . . . . . . . . . . . . . . . . . . . 194 Door Courtesy . . . . . . . . . . . . . . . . . . . . . . . . . . 562 Shift Indicator Light . . . . . . . . . . .
MAINTAINING YOUR VEHICLE WARNING! A transient high tension occurs at the bulb sockets of High Intensity Discharge (HID) headlights when the headlight switch is turned ON. It may cause serious electrical shock or electrocution if not serviced properly. See your authorized dealer for service. 4. Push the replacement bulb into the socket assembly. 5. Reinstall the bulb and socket assembly into the headlight assembly, and then turn it clockwise.
MAINTAINING YOUR VEHICLE 309 Tail/Stop, Tail, Turn Signal Light, and Backup Light 1. Open the Trunk. 2. Remove two fasteners from the back of the tail light assembly. 3 — Park/Turn Light Bulb 7 CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. 3. Pull back the trunk liner. 4. Remove the remaining fastener from the back of the tail light assembly. 5.
MAINTAINING YOUR VEHICLE 6. Disconnect the electrical connector. 7. Pull the tail light assembly clear from the vehicle to access the bulbs. Turn bulb sockets counter-clockwise to remove. 8. Turn the appropriate bulb and socket assembly counter-clockwise to remove it from the tail light assembly.
MAINTAINING YOUR VEHICLE 2 — Tail Light Bulb 3 — Turn Signal Light Bulb 311 7
MAINTAINING YOUR VEHICLE License Light 1. Remove the screws securing the light to the rear fascia. 2. Remove the bulb and socket assembly. 3. Pull the bulb out of the socket assembly. 4 — Backup Light Bulb 9. Pull the bulb out of the socket assembly. 10. Push the replacement bulb into the socket assembly. 11. Reinstall the bulb and socket assembly into the tail light assembly, and then turn it clockwise. 12. Reinstall the tail light assembly, fasteners, electrical connector, and trunk liner. 13.
MAINTAINING YOUR VEHICLE 4. Push the replacement bulb into the socket assembly. FLUIDS AND CAPACITIES 5. Reinstall the bulb and socket assembly. 6. Reattach the light to the rear fascia, and then install the screws. 313 Fuel (approximate) 6.1 Liter Engine U.S. Metric 19 gallons 72 liters Engine Oil with Filter 6.1 Liter Engine (SAE 0W-40) 7 qts. 6.6 liters Cooling System * 6.1 Liter Engine (Mopar威 15.2 qts 14.4 liAntifreeze/Coolant 5 Year/ ters 100,000 Mile Formula) or equivalent.
MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil (6.1 Liter) Oil Filter (6.1 Liter) Spark Plugs Fuel Selection (6.
MAINTAINING YOUR VEHICLE 315 Chassis Component Automatic Transmission Brake Master Cylinder Power Steering Reservoir Rear Axle Fluids, Lubricants, and Genuine Parts Mopar威 ATF+4 Automatic Transmission Fluid. Mopar威 DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. Mopar威 Power Steering Fluid + 4, Mopar威 ATF+4 Automatic Transmission Fluid. API Certified GL-5 SAE 75W140 Synthetic Gear Lubricant or equivalent.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . 318 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 321 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . 318 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 318 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES • Taxi, police, or delivery service (commercial service).〫 • Off-road or desert operation. NOTE: If ANY of these apply to you, then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow the maintenance recommendations in Schedule “B” in this section.
M A I N T E N A N C E S C H E D U L E S 8 320 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check tire pressure and look for unusual wear or damage. • Change the engine oil filter. • Inspect the battery, and clean, and tighten the terminals as required. • Check the fluid levels of coolant reservoir and brake master cylinder, and add as needed. • Check all lights and all other electrical items for correct operation. • Check rubber seals on each side of the radiator for proper fit.
SCHEDULE “B” SCHEDULE “B” Follow Schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (100 000 km) if the vehicle is usually operated under one or more of the conditions marked with an 〫. • Day or night temperatures are below 32°F (0°C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km).
M 322 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Inspect the air cleaner filter and replace if reE quired.* S C H E D U L E S 8 Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Replace the air conditioning filter. Rotate the tires.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Check and replace, if necessary, the PCV valve. * Replace the air conditioning filter. Rotate the tires.
M 324 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Inspect the air cleaner filter and replace if reE quired.* S C H E D U L E S 8 Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Change the rear axle fluid. Replace the air conditioning filter. Rotate the tires.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Check and Inspect the accessory drive belt and tensioner. Replace if required. Check and replace, if necessary, the PCV valve. * ‡ Change the power steering fluid Change the automatic transmission fluid and filter. Replace the air conditioning filter.
M 326 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Inspect the air cleaner filter and replace if reE quired.* S C H E D U L E S 8 Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Check and replace, if necessary, the PCV valve. * ‡ Replace the air conditioning filter. Rotate the tires.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Replace the spark plugs. Check and Inspect the accessory drive belt and tensioner. Replace if required. Change the rear axle fluid. Replace the air conditioning filter. Flush and replace engine coolant at 102,000 miles if not done at 60 months. Rotate the tires.
M 328 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not reA placed at 3 months. N C Inspect the air cleaner filter and replace if reE quired.* S C H E D U L E S 8 Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Check and replace, if necessary, the PCV valve. * Change the automatic transmission fluid and filter. Replace the air conditioning filter.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Check and Inspect the accessory drive belt and tensioner. Replace if required. Replace the air conditioning filter. Rotate the tires.
M 330 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not reA placed at 3 months. N C Inspect the air cleaner filter and replace if reE quired.* S C H E D U L E S 8 138,000 (230 000) X 141,000 (235 000) X 144,000 (240 000) X 147,000 (245 000) X X X X X Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Change the rear axle fluid. Replace the air conditioning filter. Rotate the tires.
SCHEDULE “A” 331 M SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Replace the air conditioning filter. Rotate the tires.
M 332 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Inspect the air cleaner filter and replace if E required.* S C H E D U L E S 8 Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Check and Inspect the accessory drive belt and tensioner. Replace if required. Flush and replace engine coolant at 60 months if not done at 102,000 miles. Check and replace, if necessary, the PCV valve.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Check and Inspect the accessory drive belt and tensioner. Replace if required. Replace the spark plugs. Check and replace, if necessary, the PCV valve. *‡ Flush and replace the engine coolant at 102,000 miles if not done at 60 months. Replace the air conditioning filter.
M 334 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Inspect the air cleaner filter and replace if reE quired.* S C H E D U L E S 8 Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Check and Inspect the accessory drive belt and tensioner. Replace if required. Check and replace, if necessary, the PCV valve. * Replace the air conditioning filter.
SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect the front and rear brake linings and rotors. Replace the air conditioning filter. Rotate the tires. * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emissions warranty. ‡ This maintenance is not required if previously replaced.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338 ▫ Prepare For The Appointment . . . . . . . . . . . . 338 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 338 䡵 Reporting Safety Defects . . . . . . . . . . . . . . . . . 341 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 341 䡵 Publication Order Forms . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center.
IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unexpected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands behind only the manufacturer’s Service Contracts. If you purchased a manufacturer’s Service Contract, you will receive Plan Provisions and an Owner Identification Card in the mail within three weeks of your vehicle delivery date.
IF YOU NEED CONSUMER ASSISTANCE REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect, which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
IF YOU NEED CONSUMER ASSISTANCE • Service Manuals. These comprehensive service manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing DaimlerChrysler Corporation vehicles. A complete working knowledge of the vehicle, system, and/or components is written in straightforward language with illustrations, diagrams, and charts. • Diagnostic Procedure Manuals.
IF YOU NEED CONSUMER ASSISTANCE 343 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your car. Traction Grades The traction grades, from highest to lowest, are AA, A, B, and C.
IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . . 211 Adding Engine Coolant (Antifreeze) . . . . . . . . . 289 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 249 Adding Washer Fluid . . . . . . . . . . . . . . 104,106,285 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 108 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . . . . . . . . . . . . . . 279 Air Conditioner Maintenance . . . . . . . . . . . . . . 282 Air Conditioning Filter . . . . . . . . . .
INDEX Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 Special Additives . . . . . . . . . . . . . . . . . . . . . 295 Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . 205,207 Ball Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281 Emergency Starting . . . . . . . . . . . . . . . . . . . . 262 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Check Engine Light (Malfunction Indicator Light) . . . . . . . . . . . . . . 273 Child Restraint . . . . . . . . . . . . . . . . . . . 47,49,52,53 Child Restraint Tether Anchors . . . . . . . . . . . 50,52 Child Safety Locks . . . . . . . . . . . . . . . . . . . . . . . 23 Clean Air Gasoline . . . . . . . . . . . . . . . . . . . . . . 246 Cleaning Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297 Climate Control . . . . . . . . . . . . . . . . . . . . . . . . 183 Clock . . . .
INDEX Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Door Locks, Automatic . . . . . . . . . . . . . . . . . . . 22 Door Opener, Garage . . . . . . . . . . . . . . . . . . . . 116 Drive Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278 Driving On Slippery Surfaces . . . . . . . . . . . . . . . . . . 209 DVD Player (Video Entertainment System) . . . . 174 Electric Remote Mirrors . . . . . . . . . . . . . . . . . . . 64 Electrical Power Outlets . . . . . . . . . . . . .
INDEX Exterior Lighting . . . . . . . . . . . . . . . . . . . . . . . . 95 Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 279 Air Conditioning . . . . . . . . . . . . . . . . . . 189,283 Engine Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 279 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . 278,314 Engine Oil Disposal . . . . . . . . . . . . . . . . . . . 278 Flashers Hazard Warning . . . . . . . . . . . . . . . . . . . . . . 256 Turn Signal . . . . . . . . .
INDEX Gas Cap (Fuel Filler Cap) . . . . . . . . . . . . . . 249,272 Gasoline, Clean Air . . . . . . . . . . . . . . . . . . . . . 246 Gasoline (Fuel) . . . . . . . . . . . . . . . . . . . . . . . . 246 Gasoline, Reformulated . . . . . . . . . . . . . . . . . . 246 Gauges Coolant Temperature . . . . . . . . . . . . . . . . . . 139 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . 136 Tachometer . . . . . . . . . . . . . . . .
INDEX Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . 47,48 Inflation Pressure Tires . . . . . . . . . . . . . . . . . . . 141 Information Center, Vehicle . . . . . . . . . . . . . . . 144 Instrument Cluster . . . . . . . . . . . . . . . . . . . 135,136 Instrument Panel and Controls . . . . . . . . . . . . . 134 Instrument Panel Lens Cleaning . . . . . . . . . . . . 299 Interior Appearance Care . . . . . . . . . . . . . . . . . 298 Interior Fuses . . . . . . . . . . . . . . . . . . . .
INDEX Fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98,136 Hazard Warning Flasher . . . . . . . . . . . . . . . . 256 Headlight Switch . . . . . . . . . . . . . . . . . . . . . . 95 Headlights . . . . . . . . . . . . . . . . . . . . . . . . 95,307 Headlights On With Wipers . . . . . . . . . . . 96,102 High Beam . . . . . . . . . . . . . . . . . . . . . . . . 99,140 High Beam Indicator . . . . . . . . . . . . . . . . . . . 140 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . .
INDEX Maintenance Schedule . . . . . . . . . . . . . . . . . . . 318 Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . . 331 Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 321 Malfunction Indicator Light (Check Engine) . . . . . . . . . . . . . . . . . . . . . . 143,273 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . 341 Memory Feature (Memory Seat) . . . . . . . . . . . . . 90 Memory Seat . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Overhead Console . . . . . . . . . . . . . . . . . . . . . . 115 Overheating, Engine . . . . . . . . . . . . . . . . . . . . . 256 Owner’s Manual (Operator Manual) . . . . . . . . . 341 Panic Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Park Assist System, Rear . . . . . . . . . . . . . . . . . 112 Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . 210 Parking On Hill . . . . . . . . . . . . . . . . . . . . . . . . 210 Passing Light . . . . . . . . . . . . . . . . . . .
INDEX Rear Window Features . . . . . . . . . . . . . . . . . . . 191 Reclining Front Seats . . . . . . . . . . . . . . . . . . . . . 86 Recorder, Event Data . . . . . . . . . . . . . . . . . . . . . 46 Recreational Towing . . . . . . . . . . . . . . . . . . . . . 254 Reformulated Gasoline . . . . . . . . . . . . . . . . . . . 246 Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283 Reminder, Seat Belt . . . . . . . . . . . . . . . . . . . . . . 35 Remote Keyless Entry (RKE) . . . .
INDEX Rear Folding . . . . . . . . . . . . . . . . . . . . . . . . . 89 Reclining . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Security Alarm (Theft Alarm) . . . . . . . . . . . . 15,140 Selection of Coolant (Antifreeze) . . . . . . . . . 288,314 Sentry Key (Immobilizer) . . . . . . . . . . . . . . . . . . 12 Service Assistance . . . . . . . . . . . . . . . . . . . . . . 338 Service Contract . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Telescoping Steering Column . . . . . . . . . . . . . . 107 Temperature Control, Automatic (ATC) . . . . . . . 183 Temperature Gauge, Engine Coolant . . . . . . 139,257 Tether Anchor, Child Restraint . . . . . . . . . . . . . . 50 Theft Alarm (Security Alarm) . . . . . . . . . . . . . . . 15 Theft System (Security Alarm) . . . . . . . . . . . . . . 15 Tilt Steering Column . . . . . . . . . . . . . . . . . . . .
INDEX Transmitter Battery Service (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . 19 Transmitter, Garage Door Opener (HomeLink威) . . . . . . . . . . . . . . . . . . . . 116 Transmitter Programming (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . 19 Transmitter, Remote Keyless Entry (RKE) . . . . . . 17 Transporting Pets . . . . . . . . . . . . . . . . . . . . . . . . 55 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . 233 Trip Odometer . . . . . . . . . . . . . . . . . .
INDEX Window Fogging . . . . . . . . . . . . . . . . . . . . . . . 189 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Windshield Defroster . . . . . . . . . . . . . . . . . . . . 187 Windshield Washers . . . . . . . . . . . . . . . 101,102,285 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285 Windshield Wiper Blades Windshield Wipers . . . . . Wiper Blade Replacement Wipers, Intermittent .
