TABLE OF CONTENTS SECTION PAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1 1 INTRODUCTION 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4 UNDERSTANDING YOUR INSTRUMENT PANEL 5 STARTING AND OPERATING 6 WHAT TO DO IN EMERGENCIES 7 MAINTAINING YOUR VEHICLE 8 MAINTENANCE SCHEDULES 9 IF YOU NEED CONSUMER ASSISTANCE 10 INDEX . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS m Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m Vehicle Identification Number . . . . . . . . . . . . . . . 6 m How To Use This Manual . . . . . . . . . . . . . . . . . . 4 m Vehicle Modifications/Alterations . . . . . . . . . . . . 7 m Warnings And Cautions . . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures, which could result in an accident or bodily injury. It also contains CAUTIONS against procedures, which could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS 1 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . . .13 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .13 ▫ Locking Doors With The Key . . . . . . . . . . . . . .14 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .15 m Sentry Key — If Equipped . . . . . . . . . . . . . . . . .15 ▫ Replacement Keys . . . . . . . . . . . . . . . . . . . . . .16 ▫ Sentry Key Programming . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Unlock The Doors And Liftgate . . . . . . . . . .24 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .32 ▫ To Lock The Doors And Liftgate (If Equipped With Power Options) . . . . . . . . . .25 ▫ To Turn Off “Flash Lights With Lock” . . . . . . . .32 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .25 ▫ To Turn Off “Flash Lights With Lock” . . . . . . . .26 ▫ Programming Additional Transmitters . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 m Emergency Deck Lid Release Latch (Convertible) . . . . . . . . . . . . . . . . . . . . . . . . . . .42 ▫ Driver And Front Passenger Supplemental Restraint System (SRS) - Airbag . . . . . . . . . . . .54 m Power Windows . . . . . . . . . . . . . . . . . . . . . . . .43 ▫ Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .71 ▫ Auto Down Feature . . . . . . . . . . . . . . . . . . . .44 m Occupant Restraints (Convertible) . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE m Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . 113 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 113 ▫ Periodic Safety Checks You Should Make Outside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place. Vehicle Key 13 Ignition Key Removal Automatic Transaxle Place the shift lever in PARK and make sure that the shift knob push button has returned to the out position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If you try to remove the key before you place the lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key-In-Ignition Reminder Opening the driver’s door when the key is in the ignition, sounds a signal to remind you to remove the key. NOTE: With the driver’s door open, and the key in the ignition, both the power door locks and Remote Keyless Entry (RKE) will not function. SENTRY KEY — IF EQUIPPED The Sentry Key Immobilizer System prevents unauthorized operation of the vehicle by disabling the engine.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. • Exxon/Mobil Speed Pass,™ additional Sentry Keys, or any other transponder equipped components on the same keychain will not cause a key-related (transponder) fault unless the additional part is physically held against the ignition key being used when starting the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sentry Key Programming You can program new keys to the system if you have two valid sentry keys by performing the following procedure: 1. Cut the additional Sentry Key Transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the ignition switch and turn the ignition switch ON for at least 3 seconds but no longer than 15 seconds. Turn the ignition switch OFF and remove the first key. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE STEERING WHEEL LOCK — IF EQUIPPED Your vehicle may be equipped with a passive steering wheel lock. This lock prevents steering the vehicle without the ignition key. If the steering wheel is moved no more than 1/2 turn in either direction and the key is not in the ignition switch, the steering wheel will lock. If You Wish To Manually Lock The Steering Wheel: With the engine running, turn the steering wheel upside down, turn off the engine and remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 WARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death. CAUTION! Door Lock Plunger WARNING! For personal security, and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks A door lock switch is on each front door panel. Press this switch to lock or unlock the doors. 1. The Auto Lock feature is enabled. 2. The transmission is in gear. 3. All doors are closed. 4. The throttle is pressed. 5. The vehicle speed is above 15 mph (24 km/h). 6. The doors were not previously locked using the power door lock switch or remote keyless entry transmitter. The Automatic Door Lock feature can be enabled or disabled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 1. Close all doors and place the key in the ignition. 6. The vehicle speed is 0 mph (0 km/h). 2. Cycle the ignition switch between LOCK and ON and back to LOCK 4 times ending up in the LOCK position. The Auto Unlock feature can be enabled or disabled. Refer to “Personal Settings” (Customer Programmable Features) in the Electronic Vehicle Information Center (EVIC) — if equipped section of this manual. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE “Child-Protection” Door Lock System (Rear Doors) — If Equipped To provide a safer environment for children riding in the rear seat, the rear doors have the “child-protection” door lock system. To use the system, open each rear door and move the control UP to engage. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! 23 REMOTE KEYLESS ENTRY (SEDAN) Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. 2 NOTE: For emergency exit with the system engaged, move the lock plunger up (unlocked position), roll down window and open the door with the outside door handle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The line of transmission must not be blocked with metal objects. To unlock the doors and liftgate: Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors and liftgate. When the UNLOCK button is pressed, the illuminated entry will initiate, and the parking lights will flash on twice.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pressing the LOCK button on the keyfob while you are inside the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. 5. If the desired programming was not achieved or to reactivate this feature, repeat the above steps.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The panic alarm will stay on for 3 minutes unless you turn it off by pressing the PANIC button a second time or if the vehicle speed is 5 mph (8 km/h) or greater. NOTE: When you turn off the panic alarm by pressing the PANIC button a second time, you may have to be closer to the vehicle due to the radio frequency noises of the system. To Turn Off “Flash Lights With Lock” NOTE: The Flash Lights With Lock feature can be turned on or off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: When entering program mode using that fob, all other programmed fobs will be erased and you will have to reprogram them for your vehicle. Use the Following procedure to program additional key fobs if the vehicle is not equipped with Sentry Key: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (Fastening the seatbelt will cancel any chiming that may confuse you during this programming procedure). 3. Place the key into the ignition. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 14. Your vehicle will remain in program mode up to 60 seconds from when the original chime was heard. After 60 seconds, all programmed fobs function normally. NOTE: If you do not have a programmed transmitter, contact your dealer for details. General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE flat blade to pry the two halves of the transmitter apart. Make sure not to damage the elastomer seal during removal. 29 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To assemble the transmitter case, snap the two halves together. NOTE: If the key fob is equipped with a screw, reinstall and tighten the screw until snug.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY (CONVERTIBLE) Four Button Transmitter This system allows you to lock or unlock the doors or open the deck lid from distances of 23–50 feet (7–15 meters) using a transmitter. You don’t have to point the transmitter at the vehicle to activate the system. Each vehicle comes with two transmitters.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system can be programmed to unlock all the doors upon the first UNLOCK button press by using the following procedure: 1. Press and hold the LOCK button on a programmed key fob. 2. Continue to hold the LOCK button at least 4 seconds, but not longer than 10 seconds, then press and hold the UNLOCK button. A single chime will sound to indicate that this feature has changed. 3. Release both buttons at the same time. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The “Sound Horn On Lock” and “Flash Lamps With Lock” feature can be reactivated by repeating this procedure. The panic alarm will stay on for 3 minutes unless you turn it off by pressing the PANIC button a second time or if the vehicle speed is 5 mph (8 km/h) or greater. To Unlatch the Deck Lid Press the “Rear Release” button twice to unlatch the deck lid.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Test the flash lamps with LOCK feature while outside of the vehicle, by pressing the LOCK button on the key fob with the ignition in the LOCK position, and the key removed. NOTE: Pressing the LOCK button on the key fob, while you are in the vehicle, will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Program Each Transmitter: All transmitters to be used with your vehicle must be programmed as follows: If your Remote Keyless Entry fails to operate from a normal distance, check for these two conditions: Press and release the 9Lock9 and 9Unlock9 buttons simultaneously, followed by a press and release of ANY button on each transmitter to be programmed. You will hear a chime when a transmitter has been successfully programmed. 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 SECURITY ALARM SYSTEM — IF EQUIPPED The system monitors the doors, liftgate, and ignition switch for unauthorized operation. If something triggers the alarm, the system will signal for about 18 minutes. For the first 3 minutes the horn will sound and the headlights, park lights, tail lights and the indicator light in the cluster will flash. Then the exterior lights will flash for another 15 minutes. Separating Transmitter Halves 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To set the alarm: 1. Remove the keys from the ignition switch and get out of the vehicle. 2. Lock the door using either the door key, power door lock switch, or the Keyless Entry Transmitter and close all doors. 3. The indicator light in the instrument cluster will flash rapidly for 16 seconds. This shows that the system is arming.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Security System Manual Override The system will not arm if you lock the doors using the manual door lock plunger. 37 LIFTGATE (SEDAN) NOTE: The key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate (if equipped). Rotate the key and pull the liftgate up. To unlock the liftgate, insert the key into the lock and turn to the right.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Once unlocked, the liftgate can be opened or closed without using the key. To open the liftgate, squeeze the liftgate release touch pad located on the backside of the liftgate handle and pull the liftgate open with one fluid motion (if equipped). NOTE: In the event of a power malfunction, or the remote transmitter is inoperative, insert the key into the liftgate lock cylinder and turn to the right.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Gas props support the liftgate in the open position. However, because the gas pressure drops with temperature, it may be necessary to assist the props when opening the liftgate in cold weather. DECK LID (CONVERTIBLE) NOTE: The key that is used to start the vehicle is also used to lock or unlock the doors and open the deck lid. To open the deck lid, insert the key into the lock and turn to the right.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Deck Lid Release (Convertible) You can open the deck lid by pressing the Remote Keyless Entry Button or from inside the vehicle, using the switch located inside the glove box. On vehicles equipped with a manual transmission, the power deck lid release switch is disabled if the doors are locked, or if vehicle speed exceeds 0 mph (0 km/h), or when the clutch pedal is depressed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seat back can be unlatched by pulling down on the glow-in-the-dark lever attached to the left rear seat back latching mechanism. Emergency Seat Back Release 41 Once unlatched the seat back can be pushed forward to gain access into the interior of the vehicle. NOTE: Make sure that the elastic loop is around the emergency release handle at all times.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE EMERGENCY DECK LID RELEASE LATCH (CONVERTIBLE) WARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the deck lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat. If trapped in the trunk, children can die from suffocation or heat stroke.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE POWER WINDOWS The power window switches are located on the instrument panel above the radio. The top left switch controls the left front window and the top right switch controls the right front window. 2 The lower left switch controls the left rear passenger’s window and the lower right switch controls the right rear passenger’s window.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. Auto Down Feature The driver’s and passenger’s front window switches have an auto down feature. Press the window switch past the detent, release, and the window will go down automatically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Inserting Latch Plate Into Buckle WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. 49 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. Rear Center Lap/Shoulder Belt Retractor Lock-Out This feature is designed to lock the retractor whenever the rear seat back is not fully latched.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 WARNING! The rear center lap/shoulder belt is equipped with a lock-out feature to ensure that the rear seat back is in the fully upright and locked position when occupied. If the rear seat back is not fully upright and locked and the rear center lap/shoulder belt can be pulled out of the retractor, the vehicle should immediately be taken to your dealer for service. Failure to follow this warning could result in serious or fatal injury.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upward over the folded webbing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Reminder System (BeltAlert) If the driver’s or front passenger’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver or front passenger to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have successfully completed the programming. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 regulations that define Occupant Classification (Refer to 9Occupant Classification System9 in this section). If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seats, and their covers are also labeled SRS AIRBAG. Front Airbag Components NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE empty or is occupied by someone that is classified in the “child9 category. This could be a child, a teenager, or even a small adult. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years old and under should always ride buckled up in a rear seat. Infants in rear facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during front airbag deployment could cause serious injury. Airbags need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Driver and Front Passenger Seat Belt Pretensioners • Occupant Classification System (OCS) for the Front Passenger Seat − Occupant Classification Module − Passenger Airbag Disable (PAD) Indicator Light − Weight Sensors How The Airbag System Works • The Occupant Restraint Controller (ORC) determines if a frontal collision is severe enough to require the airbags to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the AIRBAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away. • The Occupant Classification System (OCS) is part of a Federally regulated safety system required for this vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE will not inflate even though the Passenger Airbag Disable (PAD) indicator lamp is not illuminated. 61 NOTE: Even though this vehicle is equipped with an occupant classification system, children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint (see section on child restraints).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front Passenger Seat Occupant Passenger Airbag Disable (PAD) Indicator Light OFF ON Airbag Status Adult ON Child OFF Grocery Bags, Heavy Briefcases and Other RelaON OFF tively Light Objects Empty or Very OFF* OFF Small Objects * Since the system senses weight, some small objects will turn the PAD Indicator Light on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This indicates that you should take the vehicle to an authorized dealer. The Airbag Warning Light is turned on whenever there is fault that can affect the operation of the airbag system. If there is a fault present in the OCS, both the PAD Indicator Light and the Airbag Warning Light are illuminated to show that the passenger airbag is turned off until the fault is cleared.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE determine whether the front passenger airbag should be turned off. It also determines the rate of airbag inflation during a collision. • Your vehicle has four Weight Sensors located between the seat and the floor pan. The weight sensors measure applied weight and transfers that information to the OCM. • The Side Impact (SRS) Seat Mounted Side Airbags (If equipped) are designed to activate only in certain side collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 • When the ORC and the impact sensors detect a collision requiring the Driver Inflatable Knee Blocker , it signals the inflator unit. A quantity of nontoxic gas is generated to inflate the Driver Inflatable Knee Blocker. The Driver Inflatable Knee Blocker inflates rearward towards the driver’s knees to help protect the knees and position you for the best interaction with the front airbag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not use prior or future model year seat covers not designated for the specific model being repaired. Always use the correct seat cover specified for the vehicle. • Do not replace the seat cover with an aftermarket seat cover. • Do not add a secondary seat cover other than those approved by DaimlerChrysler/Mopar.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • • • • • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 moment of airbag deployment, or near-deployment, and up to a quarter second of high-speed deceleration data during and/or after air bag deployment or neardeployment. EDR data are ONLY recorded if an airbag deploys, or nearly deploys, and are otherwise unavailable.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE identify a particular driver, vehicle, or crash, will be treated confidentially. Confidential data will not be disclosed by DaimlerChrysler to any third party except when: 1. Used for research purposes, such as to match data with a particular crash record in an aggregate database, provided confidentiality of personal data is thereafter preserved 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years and under should ride properly buckled up in a rear seat, if available.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Small Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to ensure you have the correct seat for your child. Use the restraint that is correct for your child: • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system. • The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it, before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the latch plate around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. • Buckle the child into the seat according to the child restraint manufacturer’s directions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the outboard positions only. Regardless of the specific type of lower attachment, NEVER install LATCHcompatible child seats such that two seats share a common lower anchorage. If you are installing LATCHcompatible child restraints in adjacent rear seating positions, you can use the LATCH anchors or the vehicle’s seat belt for the outboard position, but you must use the vehicle’s seat belt at the center position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles. Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchorages will continue to have features for installation in vehicles using the lap or lap/shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In general, you will first loosen the adjusters on the lower and tether straps so that you can more easily attach the hook or connector to the lower and tether anchorages. The tether strap should be routed under the center of the head restraint and attached to the tether anchor on the rear of the seat back. Then tighten all three straps as you push the child restraint rearward and downward into the seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 WARNING! • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a child restraint top tether strap. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS (CONVERTIBLE) Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger and if equipped, side airbags for both the driver and front passenger.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All the seats in your vehicle are equipped with Lap/ Shoulder Belts. If the belt webbing is twisted, and comes in contact with the wearers body, the twisted belt should be corrected using the Lap/Shoulder belt untwisting procedure found in this section.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 83 WARNING! • A belt that is buckled into the wrong buckle will not Latch Plate To Buckle protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! 85 Seat Belt Webbing Guide NOTE: The manufacturer recommends that the seat belt is routed through the seat belt webbing guide when using the seat belt. The seat belt webbing guide should be used to improve seat belt accessibility.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upward over the folded webbing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Reminder System (BeltAlert) If the driver’s or front passenger’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver or front passenger to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have successfully completed the programming. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 regulations that define Occupant Classification (Refer to 9Occupant Classification System9 in this section). If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seats, and their covers are also labeled SRS AIRBAG. Front Airbag Components NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE empty or is occupied by someone that is classified in the “child” category. This could be a child, a teenager, or even a small adult. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years old and under should always ride buckled up in a rear seat. Infants in rear facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during front airbag deployment could cause serious injury. Airbags need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Driver and Front Passenger Seat Belt Pretensioners • Occupant Classification System (OCS) for the Front Passenger Seat − Occupant Classification Module − Passenger Airbag Disable (PAD) Indicator Light − Weight Sensors How The Airbag System Works • The Occupant Restraint Controller (ORC) determines if a frontal collision is severe enough to require the airbags to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the AIRBAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away. • The Occupant Classification System (OCS) is part of a Federally regulated safety system required for this vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE will not inflate even though the Passenger Airbag Disable (PAD) indicator lamp is not illuminated. Passenger Airbag Disabled Light • The PAD indictor light should not be illuminated when teenagers, most children in a forward facing child restraint or booster seats, most children that can properly wear the vehicle’s seat belt, and when an adult passenger is properly seated in the front passenger seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front Passenger Seat Occupant Passenger Airbag Disable (PAD) Indicator Light OFF ON Airbag Status Adult ON Child OFF Grocery Bags, Heavy Briefcases and Other RelaON OFF tively Light Objects Empty or Very OFF* OFF Small Objects * Since the system senses weight, some small objects will turn the PAD Indicator Light on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This indicates that you should take the vehicle to an authorized dealer. The Airbag Warning Light is turned on whenever there is fault that can affect the operation of the airbag system. If there is a fault present in the OCS, both the PAD Indicator Light and the Airbag Warning Light are illuminated to show that the passenger airbag is turned off until the fault is cleared.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE determine whether the front passenger airbag should be turned off. It also determines the rate of airbag inflation during a collision. • Your vehicle has four Weight Sensors located between the seat and the floor pan. The weight sensors measure applied weight and transfers that information to the OCM. • The Side Impact (SRS) Seat Mounted Side Airbags (If equipped) are designed to activate only in certain side collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE only about half of the time it takes you to blink your eyes. It then quickly deflates while helping to protect the driver’s knees. • The Knee Impact Bolsters help protect the knees, and position everyone for the best interaction with the front airbag. The front passenger seat assembly contains critical components that affect the front passenger airbag deployment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Unapproved modifications or service procedures to the front passenger seat assembly, its related components, or seat cover may inadvertently change the airbag deployment in case of a frontal crash. This could result in death or serious injury to the front seat passenger if the vehicle is involved in an accident. A modified vehicle may not comply with required Federal Motor Vehicle Safety Standards (FMVSS).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning. • It is not advisable to drive your vehicle after the airbags have deployed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Perchlorate Material – special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate.” Airbag Light You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately. • The AIRBAG light does not come on during the 6 to 8 seconds when the ignition switch is first turned on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE addition to crash investigations initiated by DaimlerChrysler, such investigations may be requested by customers, insurance carriers, government officials, and professional crash researchers, such as those associated with universities, and with hospital and insurance organizations.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Airbag disable lamp status (if equipped) • 9Time9 of airbag deployment (in terms of ignition cycles and vehicle mileage) • Airbag deployment level (if applicable) • Impact acceleration and angle • Seatbelt status • Brake status (service and parking brakes) • Accelerator status (including vehicle speed) • Engine control status (including engine speed) • Transmission gear selection • Cruise control status • Traction/stability control status • Tire pressure m
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children who weigh more than 9 kg (20 lbs) but are less than one year old. • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward facing child restraint should only be used in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE into the retractor, as the belt retracts, you will hear a clicking sound. This indicates that the seat belt is now in the automatic locking mode. Pull on the excess webbing to tighten the lap portion about the child restraint. Follow the instructions of the child restraint manufacture. NOTE: To reset this feature you must let all of the belt webbing return into the retractor.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seat cushion. They are round bars, part of the seat and body structure, and are readily visible. In addition, there are two tether strap anchorages located behind the rear seat head form, in the convertible top storage area. 109 restraints having tether straps and hooks for connection to the top tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE installing the child restraint, buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach. If the buckled seat belt interferes with the child restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 111 WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a child restraint top tether strap. Tether Strap Mounting Not all child restraint systems will be installed as we have described here. Again, carefully follow the instructions that come with the child restraint system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back. Transporting Pets Airbags deploying in the front seat could harm your pet.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty. 113 If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc. If there is any question regarding belt or retractor condition, replace the belt. Airbag Light The light should come on and remain on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the LED is not lit during starting, have it checked.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 m Convertible Top Operation . . . . . . . . . . . . . . . . 119 ▫ Outside Mirror—Driver’s Side . . . . . . . . . . . . 132 ▫ To Lower The Top . . . . . . . . . . . . . . . . . . . . . 119 ▫ Outside Mirror—Passenger’s Side . . . . . . . . . . 132 ▫ To Raise The Top . . . . . . . . . . . . . . . . . . . . . 122 ▫ Electric Remote-Control Mirrors — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ UConnect™ System Features . . . . . . . . . . . . . 145 ▫ Heated Seats — If Equipped . . . . . . . . . . . . . 166 ▫ Advanced Phone Connectivity . . . . . . . . . . . . 150 ▫ Folding Rear Seat (Sedan) . . . . . . . . . . . . . . . 167 ▫ Things You Should Know About Your UConnect™ System . . . . . . . . . . . . . . . . . . . . 151 ▫ Folding Rear Seat (Convertible) . . . . . . . . . . . 169 ▫ General Information . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Daytime Running Lights (DRL) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 183 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . 183 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . 183 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . 184 ▫ Highbeam/Lowbeam Select Switch . . . . . . . . . 185 ▫ Passing Light . . . . . . . . . . . . . . . . . . . . . . . . 185 m Windshield Wipers And Washers . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Reprogramming A Single Button . . . . . . . . . . 199 m Rear Shelf Panel— If Equipped . . . . . . . . . . . . . 208 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 ▫ Position 1 (Top) . . . . . . . . . . . . . . . . . . . . . . 209 m Power Sunroof — If Equipped . . . . . . . . . . . . . 200 ▫ Position 2 (Middle) . . . . . . . . . . . . . . . . . . . . 210 ▫ Express Open Feature . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONVERTIBLE TOP OPERATION WARNING! The convertible top does not provide the structural protection that a reinforced metal roof does, and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision. Therefore it is important that all occupants wear their seat belts at all times when riding in a convertible.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! To fully insure that no damage occurs, be sure that the vehicle is at a complete stop with the gear selector in the Park position (automatic transaxle) or in the Neutral position (manual transaxle) before lowering or raising the top. To avoid damage to either the top or the rear window, check the top storage area at the rear of the vehicle interior to be sure that it is clear of debris or other items.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 the Power Top Switch lightly in the first detent position will lower the windows slightly and the convertible top to the full down position. Pressing and holding the switch in the second detent position will lower all four windows completely and the top to the full down position. Releasing Convertible Top Latches 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Continue pressing the Power Top Switch until the convertible top is lowered completely. 5. Install the Convertible Top Boot Cover, if equipped. Refer to Convertible Top Boot Cover Installation–If Equipped, in this section. CAUTION! Damage to the convertible top boot cover could result if the latch handle is not completely closed when the top is lowered. The convertible top boot cover cannot be installed while the latch handle is open.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 1. Remove the convertible top boot cover, if equipped. Refer to Convertible Top Boot Cover Removal and Storage, in this section. 2. Turn the ignition to the ON position. 3 3. Press the Power Top Switch to raise the top. Before the top reaches the windshield, open the latch handle and turn the handle clockwise to open the latches. Press the switch again to continue raising the top until the two pins seat themselves in the windshield header.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Car top carriers, ski racks, etc., should not be attached to the convertible top mechanism as they will damage the top. Do not place objects on the convertible top, in the top well or on the sport bar. Damage to the convertible top may occur. Convertible Top Boot Cover Installation–If Equipped 1. With the top down and the convertible top latch handle in the stowed position, lay the unfolded boot cover across the convertible top.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 2. Install the rear edge of the boot, first tucking the rear edge of the boot under the rear and both sides of the rails.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull the right and left boot arms forward and engage both boot arm snaps. Make sure both snaps are fully engaged.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Engage the boot center section retainer using the tabs provided. 127 5. Tuck the rear flap of the boot in behind the Upper Moulding.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Convertible Top Boot Cover Removal and Storage 1. Unsnap the snaps and remove the top cover boot. 2. Lay the boot cover flat with the center section retainer facing the rear of the car.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 3. First fold the left side of the boot cover to the middle of the boot cover. 3 Folding Boot Cover Right Side Folding Boot Cover Left Side 4. Second fold the right side of the boot cover to the middle, fitting it inside the left side of the boot cover and store it in the trunk or a dry secure area. CAUTION! Do not lay heavy objects on top of the boot or lay the boot on top of sharp/pointy objects. Damage could occur to the boot.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONVERTIBLE TOP MANUAL OVERRIDE If your vehicle is experiencing electrical failure (low battery, etc.) and it is necessary to raise the convertible top, perform the following steps: 1. Locate the convertible top motor bypass screw, which is found in the trunk under the convertible top storage area. 2. Turn the screw counterclockwise until the screw stops. This will relieve the hydraulic pressure and allow the convertible top to be raised manually.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Rotate the latch handle clockwise to open the latches. 5. Pull down and rotate the handle counterclockwise to engage the latches. 131 7. Close the convertible top motor bypass screw by turning the screw clockwise until it stops. Tighten the screw securely. NOTE: Failure to tighten the bypass screw securely can cause convertible top operating concerns.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield). Outside Mirror—Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Electric Remote-Control Mirrors — If Equipped The power mirror switch is located to the left of the steering column on the instrument panel. To adjust the view in the outside mirrors, turn the rotary knob to the left (L), center (O) or Right (R) position. After selecting the mirror, move the knob in the same direction you want the mirror to move. Use the center (O) position to guard against accidentally moving a mirror position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE An illuminated vanity mirror is on the sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights turn on automatically. Closing the mirror cover turns off the lights. Illuminated Vanity Mirror Sun Visor Sliding Feature The sun visors may be pulled out to provide extended coverage of the side glass.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s microphone for private conversation. The UConnect™ phonebook enables you to store up to 32 names and four numbers per name. Each language has a separate 32-name phonebook accessible only in that language. This system is driven through your Bluetooth™ Hands-Free profile cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ system can be used with any HandsFree Profile certified Bluetooth™ cellular phone. See www.chrysler.com/uconnect for supported phones. If your cellular phone supports a different profile (e.g., Headset Profile), you may not be able to use any UConnect™ features. Refer to your cellular service provider or the phone manufacturer for details.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE example, you can use the combined form voice command 9Phonebook New Entry,9 or you can break the combined form command into two voice commands: 9Phonebook9 and 9New Entry.9 Please remember, the UConnect™ system works best when you talk in a normal conversational tone, as if speaking to some one sitting eight feet away from you. Voice Command Tree Refer to “Voice Tree” at the end of this section.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the 9Ready9 prompt and the following beep, say 9Setup Phone Pairing9 and follow the audible prompts. • When prompted, after the voice on beep, say 9Pair a Phone9 and follow the audible prompts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Call/Dial by Saying a Number Call/Dial by Saying a Name • Press the ’Phone’ button to begin. • Press the “Phone” button to begin. • After the 9Ready9 prompt and the following beep, say 9Dial.9 • After the 9Ready9 prompt and the following beep, say “Dial” or Call.9 • System will prompt you to say the number you want call. • System will prompt you to say the name of the person you want call. • For example, you can say “234-567-8901.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Add Names to Your UConnect™ Phonebook NOTE: Adding names to phonebook is recommended when vehicle is not in motion. • Press the “Phone” button to begin. • After the 9Ready9 prompt and the following beep, say 9Phonebook New Entry.9 • When prompted, say the name of the new entry. Use of long names helps the voice recognition and is recommended. For example, say 9Robert Smith9 or 9Robert9 instead of 9Bob.9 • When prompted, enter the number designation (e.g.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, mobile, or pager) that you wish to edit. • When prompted, recite the new phone number for the phonebook entry that you are editing. After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After you enter the name, the UConnect™ system will ask you which designation you wish to delete, home, work, mobile, or pager. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted. After confirmation, the phonebook entries will be deleted. Note that only the phonebook in the current language is deleted. Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone Call Features The following features can be accessed through the UConnect™ system if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the UConnect™ system. Check with your cellular service provider for the features that you have.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE second call is in progress. To go back to the first call, refer to 9Toggling Between Calls.9 To combine two calls, refer to 9Conference Call.9 Place/Retrieve a Call from Hold To put a call on hold, press the 8Phone’ button until you hear a single beep. This indicates that the call is on hold. To bring the call back from hold, press and hold the 8Phone’ button until you hear a single beep.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE hold may not become active automatically. This is cell phone dependent. To bring the call back from hold, press and hold the ‘Phone’ button until you hear a single beep. Redial • Press the ’Phone’ button to begin. • After the 9Ready9 prompt and the following beep, say 9Redial.9 • The UConnect™ system will call the last number that was dialed on your cellular phone. Note: this may not be the last number dialed from the UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the 9Ready9 prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped). • Continue to follow the system prompts to complete language selection. After selecting one of the languages, all prompts and voice commands will be in that language. NOTE: After every UConnect™ language change operation, only the language specific 32-name phonebook is usable.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your phone must be turned on and paired to the UConnect™ system to allow use of this vehicle feature in emergency situations when the cell phone has network coverage and stays paired to the UConnect™ system. Towing Assistance If you need towing assistance, • Press the ’Phone’ button to begin. • After the 9Ready9 prompt and the following beep, say 9Towing Assistance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When calling a number with your UConnect™ system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’Voice Recognition’ button and say the sequence you wish to enter followed by the word 9Send.9 For example, if required to enter your pin number followed with a pound 3 7 4 6 #, you can press the ’Voice Recognition’ button and say 93 7 4 6 # Send.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth™ cellular phone, the audio will be played through your vehicle’s audio system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Information Service When using AT&T Wireless Service, dialing to phone number 9#121,9 you can access voice activated automated system to receive news, weather, stocks, traffic, etc. related information. If you would like to connect or disconnect the Bluetooth™ connection between a UConnect™ paired cellular phone and the UConnect™ system, then follow the instruction described in your cellular phone user’s manual.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system. The phone must have been previously paired to the UConnect™ system that you want to use it with. Delete UConnect™ Paired Cellular Phones • Press the ’Phone’ button to begin. • At the next prompt, say 9Delete9 and follow the prompts. • After the 9Ready9 prompt and the following beep, say 9Setup Select Phone9 and follow the prompts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE training mode, follow one of the two procedures: From outside the UConnect mode (e.g. from radio mode), • Press and hold the ‘Voice Recognition’ button for 5 seconds until the session begins, or • Press the ‘Voice Recognition’ button and say 9Setup, Voice Training9 command. Repeat the words and phrases when prompted by the UConnect System.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 • In a convertible vehicle, the system performance may be compromised with roof top down. • You can say 9O9 (letter 9O9) for 909 (zero). 98009 must be spoken 9eight-zero-zero.9 • Even though the system is designed for users speaking in North American English, French, and Spanish accents, the system may not always work for some.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In a convertible vehicle, the system performance may be compromised with roof top down. switching the phone off/on. Your cell phone is recommended to remain in Bluetooth 9on9 mode. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary Zero One Two Three Four Five Six Seven Eight Nine Star (*) Plus (+) Pound (#) Add Location All North American English Alternate(s) Call Cancel Confirmation Prompts Continue Delete Dial Edit Emergency English Erase All Espanol Francais Help Home Language List names List phones
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mobile Mute Mute off New entry No Pager Pair a phone Phone pairing Phonebook Previous Record again Redial Return to main menu Select phone Send Set up 159 Towing assistance Transfer call Try again Voice training Work Yes Pairing Phone book General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. Return.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Front Seat Adjustment The adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position. Manual Adjustment Bar Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched. WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Seat Adjuster — If Equipped WARNING! 161 6 - Way Power Seat with Manual Recliner The seat switch is on the outboard side of the seat near the floor. Use this switch to move the seat up or down, forward or rearward, or to tilt the seat. Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE This seat also has a manual recline lever located just to the rear of the power seat switch. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position. Manual Lumbar—If Equipped The Lumbar adjustment is located on the inboard side of the driver’s seat. To increase support, rotate the handle down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Front Passenger Seat — If Equipped The passenger front seat may be folded fully forward to provide additional cargo space. To fold the seat forward pull up on the recliner lever located on the outboard side of the seat. 163 Driver’s Seat Back Tilt—If Equipped How to operate the driver’s seat: 1. Push the lever down until seat back releases. 2. Push the seat back forward. 3. To return seat to a sitting position, push seat back rearward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The driver’s front seat has a full recliner memory, which will allow the seat back to return to its original position. Passenger Seat Back Tilt (Easy Entry System) (Convertible) How to operate the passenger front seat: 1. Push the lever down until seat back releases. 2. Push seat back forward until it slides toward the dashboard.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 3. To return seat to a sitting position, rotate seat back upright until it locks. 4. Push seat rearward until the track locks. NOTE: The passenger front seat has a full recliner memory, which will allow the seat back to returned to its original position. 3 NOTE: The passenger front seat has a track memory, which returns the seat to just past the half way point of the track regardless of original position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When high-temperature heating is selected, the heaters provide a boosted heat level during the first four minutes of operation after heating is activated. The heat output then drops to the normal high-temperature level. If high-level heating is selected, the system will automatically switch to the low level after about 30 minutes of continuous operation. At that time, the number of illuminated LEDs changes from two to one, indicating the change.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts • Be sure that everyone in your vehicle is in a seat and using a seat belt properly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat (Convertible) To provide additional storage area, each rear seatback can be folded forward. The seat back release knobs are located in the trunk area. Pull the left side seatback release knob to fold down the left side seatback. Pull the right side seatback release knob to fold down the right side seatback.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure that everyone in your vehicle is in a seat and using a seat belt properly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 3 Folding Rear Seat Button Tumbling Seat Release Strap • Pull the release handle located on the outboard side of the seat. Lift up the seat and tumble the seat forward. • Attach the elastic strap, located at the base of the seat cushion, onto the hook bar on the center trim panel to hold the seat in place.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tumbling Rear Seat (Convertible) To provide additional storage area, each rear seat can be tumbled forward. CAUTION! Tumbling Seat Strap To return the rear seat to it’s upright latched position, rotate the seat cushion rearward to latch the seat. Then lift the seatback to its upright latched position. NOTE: The elastic strap should be reinstalled in the clip on the base of the seat cushion before returning the seat to its normal position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE the left side seatback. Pull the right side seatback release knob to fold down the right side seatback. 173 2. From inside the vehicle, fold the rear seat back down flat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull the release handle located at the bottom of the folded seat back and tumble the seat forward. Cinching Tether Strap Tumbling Rear Seat 4. Attach the cinching tether strap, located at the side of the seat cushion, onto the hook bar on the center trim panel and tighten by pulling the cinching strap until the seat is secure. To return the tumbling rear seat to the latched (normal) position use the following procedure: 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 NOTE: Prior to rotating the seat cushions rearward, be sure that the rear seat belt buckles are secured with the straps, so that the buckles are accessible. 3 Releasing Cinching Tether Strap 2. Disconnect the cinching tether strap. NOTE: The strap should be reinstalled in the side pocket on the seat cushion before returning the seat to the latched (normal) position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Rotate the seat cushion rearward to latch the seat. Then lift the seatback to its upright latched position. WARNING! In an accident, you or others in your vehicle could be injured if seats are not properly latched to their attachments. Always be sure the seats are fully latched. Rear Seat Removal (Sedan) The rear seats can be removed to provide more cargo space. • Push and hold the button on the seatback and fold down the rear seatback.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 3 Tumbling Seat Release Strap Release Lever Location • Lift up the release levers to disengage the seat from the floor attachments. • Using the handle on the seat, the seat assembly can now be lifted and removed from the vehicle. NOTE: Small rollers on the bottom of the folded seat and a handle at the top allow the seat to be easily moved when removed from the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To reinstall the rear seat, insert the seat into the floor attachments. Lower the release levers of the seat to latch the front floor attachments and rotate the seat rearward to latch the seat. Lift the seat back to its upright latched position. TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the primary hood release lever located under the left side of the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then move the secondary hood latch (safety latch) located under the front edge of the hood, slightly to the right of center, and raise the hood. 179 Use the hood prop rod clipped to the driver’s side of the engine compartment to secure the hood in the open position. Place the hood prop at the location stamped into the inner hood surface. To prevent possible damage, do not slam the hood to close it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Map/Reading Lights (Sedan) These lights are mounted between the sun visors above the rear view mirror. Each light is turned ON by pressing the button. Press the button a second time to turn the light OFF. The lights also come on when a door is opened or the dimmer control is turned fully upward, past the second detent.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Map/Reading Lights (Convertible) When the ignition switch is in the ON position, these lights, located under the rearview mirror can be turned on by switches located at the base of the rearview mirror. 181 NOTE: The lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. They will not turn off automatically.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights, Parking Lights, Instrument Panel Lights Turn the end of the Multi-Function Control Lever to the first detent for parking light operation. Turn to the second detent for headlight operation. To change the brightness of the instrument panel lights, rotate the center portion of the Multi-Function Control Lever up or down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights (DRL) — If Equipped The high beam lights will come on as Daytime Running Lights (DRL) at DRL intensity (lower), whenever the ignition is on, the engine is running, the headlight switch is off, the parking brake is off, the turn signal is off, and the gear shift is in any position except park.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The fog lights will only operate with the headlights on low beam. Selecting high beam headlights will turn off the fog lights. Turn Signals Move the Multi-Function Control Lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down without moving beyond the detent.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Highbeam/Lowbeam Select Switch 185 Passing Light You can signal another vehicle with your headlights by lightly pulling the Multi-Function Control Lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released. NOTE: If the Multi-Function Control Lever is held in the flash to pass position for more than 15 seconds, the high beams will shut off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch on the control lever. The lever is located on the right side of the steering column. Rotate the control to select the desired wiper speed. Windshield Washers To use the washer, pull the control lever toward you and hold while spray is desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mist Feature 187 CAUTION! In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted. Mist Control Push down on the wiper control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range. The delay interval decreases as you rotate the knob until it enters the LO continual speed position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, push down on the lever below the multifunction control lever and move the steering wheel up or down, as desired. Pull the lever back up to lock the column firmly in place. Tilt Steering Column Control 189 WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at approximately either 30 mph (40 km/h ) or 35 mph (56 km/h) depending on the model or engine size. The speed control lever is located on the right side of the steering wheel. To Activate: Push the ON/OFF button. The CRUISE indicator in the instrument cluster will illuminate. To turn the system OFF, push the ON/OFF button a second time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 To Set At A Desired Speed: When the vehicle has reached the desired speed, press down on the lever and release. Release the accelerator and the vehicle will operate at the selected speed. To Resume Speed: To resume a previously set speed, push the “RESUME ACCEL” lever up and release. Resume can be used at any speed above 20 mph (32 km/h). NOTE: The vehicle should be traveling at a steady speed and on level ground before pressing the SET lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tapping the “SET DECEL” button once will result in a 1 mph (2 km/h) speed decrease. Each time the button is tapped, speed decreases. To Accelerate For Passing: Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Manual Transaxle: Depressing the clutch pedal will disengage the speed control. A slight increase in engine RPM before the speed control disengages is normal.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 GARAGE DOOR OPENER — IF EQUIPPED NOTE: The HomeLinkt system will be disabled if the Vehicle Theft Alarm (if equipped) is in the Prearmed, Armed or Alarming state. The HomeLinkt system will only operate when the Vehicle Theft Alarm (if equipped) is in the Disarmed mode. The HomeLinkt Universal Transceiver replaces up to three remote controls (hand held transmitters) that operate devices such as garage door openers, motorized gates, or home lighting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! HomeLink Buttons (Convertible) For additional information on HomeLinkt, call 1–800– 355–3515, or on the internet at www.homelink.com. A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming The Universal Transceiver For best results, install a new battery in the hand held transmitter before programming. If your garage door opener (located in the garage) is equipped with an antenna, make sure that the antenna is hanging straight down. 1. Turn off the engine. WARNING! Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Choose one of the three Universal Transceiver buttons to program. Place the hand held controller one to three inches from the Universal Transceiver while keeping its indicator light in view. HomeLink Programming (Convertible) 4. Using both hands, press the hand held transmitter button and the desired Universal Transceiver button. Do not release the buttons until step 5 has been completed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 5. The indicator light in the Universal Transceiver will begin to flash, first slowly and then rapidly. The rapid flashing indicates successful programming. If after 90 seconds the indicator light does not flash rapidly or goes out, return to step 1 and repeat the procedure. To train the other buttons, repeat steps 3 and 4. Be sure to keep your hand held transmitters in case you need to retrain the Universal Transceiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The assistance of a second person may make the following programming procedure quicker and easier. 1. Locate the training button on the garage door motor head unit. The exact location and color of the button may vary by garage door opener manufacturer. If you have difficulty in locating the training button, check your garage door opener manual, or call 1-800-355-3515 or, on the Internet, at www.homelink.com. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Universal Transceiver light will flash slowly and then rapidly when the programming is successful. NOTE: When programming such a garage door opener or gate, unplug the device to prevent possible damage to the garage door or gate motor. Operation Press and hold the desired button on the Universal Transceiver until the garage door or other device begins to operate. The light in the display shows that the signal is being transmitted.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. HomeLinkt is a trademark owned by Johnson Controls, Inc. POWER SUNROOF — IF EQUIPPED The power sunroof switch is located in the reading lamp.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press and hold the button in the center of the sunroof switch to open the vent. The sunroof can be stopped at any position between closed and full vent. To close the sunroof from the vent position, press and hold the switch forward. Releasing the switch will stop the movement of the sunroof and the sunroof will remain in the partial vent position until the switch is pushed forward again.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. Do not allow small children to operate the sunroof. Never allow fingers or other body parts, or any object to project through the sunroof opening. Injury may result.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 There are two optional power outlets. One is in the center console/armrest lower storage bin. 3 Front Power Outlet It will accept a cigar lighter unit, which is part of the optional Smokers Package. To preserve the heating element of the cigar lighter unit, do not hold the lighter in the heating position. As a child safety precaution, this outlet is powered by the ignition switch, only when the switch is in the 9ON9 or 9ACCESSORY9 positions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The second is in the right rear cargo area. This outlet is powered directly by the battery (as an option, fuse #11 in the Integrated Power Module (IPM), may be repositioned to allow power to come from the ignition switch only when in the 9ON9 or 9ACCESSORY9 positions). NOTE: Neither of the power outlets will accept a cigar lighter unit. They are intended only for accessory usage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e. coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged into the 12 volt power outlet, draw power from the vehicle’s battery, even when not in use; i.e. cellular phones, etc. Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power such as coolers, vacuum cleaners, lights, etc., will discharge the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 Push the upper button on the front of the armrest to raise the upper cover. Inside is a slot for a power cord, an area to store a cell phone, and other miscellaneous items. Push the lower button on the front of the armrest, and raise the armrest for access to the lower storage bin. The lower storage has a power outlet (if equipped), a slot for a power cord, and can be used for storing up to six CD’s and other miscellaneous items.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e. coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 WARNING! • To avoid tipping, lock the shelf securely in all positions. • Do not drive this vehicle with the liftgate open, or use the shelf as a seat. 3 • Failure to follow these warnings could result in serious or fatal injury. Position 1 (Top) Insert the front outboard corners of the shelf panel into the top guides and slide forward. Press down on the back of the shelf panel to lock it into place.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Position 2 (Middle) Insert the front outboard corners of the shelf panel into the middle guides and slide forward. Press down on the back of the shelf panel to lock it into place. WARNING! Do not load objects over 100 lbs (45 kg) in position 2 (middle). Failure to follow this warning could cause the shelf to collapse resulting in personal injury. Position 3 (Floor) Insert the front outboard corners of the shelf panel into the bottom guides and slide forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Position 4 (Vertical) Insert the front outboard corners of the shelf panel into the vertical guides behind the rear seatbacks near the floor and slide downward. Push the shelf panel forward to lock it into place. 211 WARNING! When in the vertical position, the rear shelf panel should not be used as a barrier for large objects in the cargo area when the seatbacks folded down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Twist the knob on the underside of the panel and lower the shelf leg. Rear Shelf Panel Position 5 Rear Shelf Leg Release Knob 3. Install the shelf leg into the liftgate latch area as labeled on the rear scuff plate. WARNING! Do not load objects over 100 lbs (45 kg) in position 5 (table). Failure to follow this warning could cause the shelf to collapse resulting in personal injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Use both adjustable crossbars assemblies to support the load and distribute the load as evenly as possible.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately. Long loads which extend over the windshield, such as wood panels or surfboards, should be secured to both the front and rear of the vehicle. Cargo must be securely tied before driving your vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Electric Rear Window Defroster Rear Defroster Switch The push-button is located at the center of the instrument panel, below the radio. Press this button to turn on the rear window defroster, and the optional electric remote control heated mirrors. An amber light shows that the defroster is on. NOTE: The defroster turns off automatically after 10 minutes of operation. Each following activation of the defroster will last for five minutes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adding Washer Fluid The fluid reservoir for the windshield washers and the rear window washer (If Equipped) is shared. It is located in the rear of the engine compartment on the passenger side and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS m Instrument Panel Features . . . . . . . . . . . . . . . . . 220 ▫ Average Fuel Economy . . . . . . . . . . . . . . . . . 234 m Instrument Cluster—Base . . . . . . . . . . . . . . . . . 221 ▫ Distance To Empty (DTE) . . . . . . . . . . . . . . . 234 m Instrument Cluster—Premium . . . . . . . . . . . . . . 222 ▫ Elapsed Time . . . . . . . . . . . . . . . . . . . . . . . . 234 m Instrument Cluster—Turbo . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Electrical Disturbances . . . . . . . . . . . . . . . . . . 241 ▫ AM Reception . . . . . . . . . . . . . . . . . . . . . . . 241 ▫ FM Reception . . . . . . . . . . . . . . . . . . . . . . . . 241 m Sales Code REF — AM/FM/CD (Single Disc) Radio With Optional Satellite Radio And Hands Free Phone Capability . . . . . . . . . . . . . . . . . . . 242 ▫ Operating Instructions - Radio Mode . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) . . . . . . . . . . . . . . . . . . . . 264 ▫ Selecting Satellite Mode In REF, And RAQ, Radios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265 ▫ Selecting a Channel . . . . . . . . . . . . . . . . . . . . 266 ▫ Storing And Selecting Pre-Set Channels . . . . . . 266 ▫ Using The PTY (Program Type) Button (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . . 266 ▫ PTY Button 9Scan9 . . .
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES
UNDERSTANDING YOUR INSTRUMENT PANEL 221 INSTRUMENT CLUSTER—BASE 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER—PREMIUM
UNDERSTANDING YOUR INSTRUMENT PANEL 223 INSTRUMENT CLUSTER—TURBO 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Fuel Door Reminder This is a reminder that the Fuel Filler Door is located on the front passenger’s (right) side of the vehicle. 3. Temperature Gauge The temperature gauge shows engine coolant temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL 5. Tachometer The white area of the scale shows the permissible engine revolutions-per-minute (rpm x 1000) for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 6. Transmission Range Indicator This display indicator shows the automatic transmission gear selection. 7. Odometer/Trip Odometer A vacuum fluorescent display indicates the total distance the vehicle has been driven.
UNDERSTANDING YOUR INSTRUMENT PANEL 9. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD that monitors emissions, engine, and automatic transmission control systems. The light will illuminate when the key is in the ON/RUN position before engine start. If the bulb does not come on when turning the key from OFF to ON/RUN, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc.
UNDERSTANDING YOUR INSTRUMENT PANEL 12. Brake System Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, there is a low brake fluid level or there is a problem with the anti-lock brake system. The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system.
UNDERSTANDING YOUR INSTRUMENT PANEL the ON position. The light should illuminate for approximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. 14. Engine Temperature Warning Light This light warns of an overheated engine condition. If the engine is critically hot, a warning chime will sound 10 times.
UNDERSTANDING YOUR INSTRUMENT PANEL 17. Low Fuel Light When the fuel level drops to 2 gallons, the fuel symbol will light and a single chime will sound. 18. Anti-Lock Warning Light (ABS) — If Equipped This light monitors the Anti-Lock Brake System (ABS) described elsewhere in this manual. This light will come on when the ignition key is turned to the ON position and may stay on for as long as four seconds. 229 The warning light should be checked frequently to assure that it is operating properly.
UNDERSTANDING YOUR INSTRUMENT PANEL turned from the OFF to the ON position, and the light will turn off after the engine is started. If the bulb does not come on during starting, have the system checked by an authorized dealer. If the light comes on and remains on while driving, stop the vehicle and shut off the engine. DO NOT OPERATE THE VEHICLE UNTIL THE CAUSE IS CORRECTED. The light does not show the quantity of oil in the engine. This can be determined using the procedure shown in Section 7.
UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC)–If Equipped 231 • System Status • Vehicle information warning message displays • Personal Settings (customer programmable features) • Compass heading • Outside temperature display • Trip computer functions • UConnect™ hands-free communication system displays — If Equipped • Audio mode display EVIC Location The Electronic Vehicle Information Center (EVIC) features a driver-interactive display.
UNDERSTANDING YOUR INSTRUMENT PANEL • Left Rear Turn Signal Lamp Out (with a single chime) • Trunk Ajar (with a single chime) • Right Front Turn Signal Lamp Out (with a single chime) • Low Washer Fluid (with a single chime) • Right Rear Turn Signal Lamp Out (with a single chime) • RKE Battery Low (with a single chime) • Personal Settings Not Available – Vehicle Not in Park (automatic transmissions) or vehicle is in motion (manual transmissions).
UNDERSTANDING YOUR INSTRUMENT PANEL 233 • Distance To Empty (DTE) EVIC Functions • Elapsed Time • Personal Settings To Reset The Display Pressing and holding the EVIC button once will clear the resettable function currently being displayed. Reset will only occur if a resettable function is currently being displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL For additional information regarding the compass, refer to Personal Settings (Customer Programmable Features) in this section. Average Fuel Economy Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read “RESET” or show dashes for two seconds. Then, the history information will be erased, and the averaging will continue from where it was before the reset.
UNDERSTANDING YOUR INSTRUMENT PANEL Press and release the EVIC button until Personal Settings is displayed in the EVIC. Use the EVIC button to display one of the following choices: Language When in this display you may select different languages for all display nomenclature, including the trip functions. Pressing the EVIC button while in this display selects English, Espanol, Deutsch, Italiano, or Francais depending on availability.
UNDERSTANDING YOUR INSTRUMENT PANEL UNLOCK ALL DOORS is selected all of the doors will unlock at the first press of the remote keyless entry unlock button. Press and hold the EVIC button when in this display until “DRIVER’S DOOR 1ST” or “ALL DOORS” appears to make your selection. Sound Horn with Remote Key Lock When ON is selected a short horn sound will occur when the remote keyless entry “Lock” button is pressed. This feature may be selected with or without the flash lights on lock/unlock feature.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 NOTE: Turning the headlights on during the daytime causes the instrument panel lights to dim. To increase the brightness, refer to “Lights” in this section. Press and hold the EVIC button when in this display until “OFF”, “30 sec.”, “60 sec.”, or “90 sec.” appears to make your selection.
UNDERSTANDING YOUR INSTRUMENT PANEL Compass Variance Compass Variance is the difference between magnetic North and Geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings. In order to ensure compass accuracy, the compass variance should be properly set according to the compass variance map zone that the vehicle is in. NOTE: Magnetic materials should be kept away from the Instrument Panel.
UNDERSTANDING YOUR INSTRUMENT PANEL To set the variance: with the ignition in the ON position, with a short button press (less than one second) press and release the EVIC button several times until you have displayed the Personal Settings (Customer Programmable Features) menu. Once in the Personal Settings (Customer Programmable Features) menu, press and release (less than one seconds) the EVIC button several times until “Compass Variance” is highlighted.
UNDERSTANDING YOUR INSTRUMENT PANEL calibration mode. The Cal indicator will come on continuously in the EVIC display to indicate that the compass is now in the calibration mode and that the vehicle can now be driven to calibrate. (A short EVIC button press from the 9Calibrate Compass (Yes)9 screen will exit the EVIC Customer Programmable features, and return it to its normal operating mode).
UNDERSTANDING YOUR INSTRUMENT PANEL RADIO GENERAL INFORMATION Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile operation and natural phenomena, which might lead you to believe your sound system is malfunctioning.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The radio, steering wheel radio controls (if equipped), and 6 disc CD/DVD changer (if equipped) will remain active for up to 10 minutes after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL SATELLITE RADIO AND HANDS FREE PHONE CAPABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it. When the audio system is turned on, the sound will be set at the same volume level as last played.
UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station in either, AM, FM, or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time.
UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control and BASS will display. Turn the TUNE control to the right or left to increase or decrease the Bass tones. Press the rotary TUNE control a second time and MID will display. Turn the TUNE control to the right or left to increase or decrease the Mid Range tones. Press the rotary TUNE control a third time and TREB will display.
UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM, 12 FM, and 12 Satellite (if equipped) stations to be stored into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 • If you insert a disc with the ignition ON and the radio OFF, the CD will automatically be pulled into the CD Player. SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. • This radio does not play discs with MP3 tracks. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal.
UNDERSTANDING YOUR INSTRUMENT PANEL RND/SET Button (Random Play Button) (CD Mode) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace.
UNDERSTANDING YOUR INSTRUMENT PANEL MUTE Button (Auxiliary Mode) Press the MUTE button to cancel the sound from the speakers. 9MUTE9 will display. Press the MUTE button a second time and the sound from the speakers will return. Rotating the volume control or turning OFF the ignition will also return the sound from the speakers. SCAN Button (Auxiliary Mode) No function. EJECT Button (Auxiliary Mode) No function. PSCAN Button (Auxiliary Mode) No function.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Radio — If Equipped Refer to the “Satellite Radio” section of the Owner’s Manual. SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, AND VEHICLE ENTERTAINMENT SYSTEMS (VES) CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it. When the audio system is turned on, the sound will be set at the same volume level as last played.
UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time. MSG or INFO Button (Radio Mode) Press the MSG or INFO button for an RBDS station (one with call letters displayed).
UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control and BASS will display. Turn the TUNE control to the right or left to increase or decrease the Bass tones. Press the rotary TUNE control a second time and MID will display. Turn the TUNE control to the right or left to increase or decrease the Mid Range tones. Press the rotary TUNE control a third time and TREBLE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the PTY button to select the following format types: Program Type No program type or undefined Adult Hits Alert Alert Classical Classic Rock College Country Emergency Test Foreign Language Information Jazz News 16 Digit-Character Display None Adult_Hits Alert Alert Classical Classic_Rock College Country Emergency Test Foreign_Language Information Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Roc
UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (CD MODE for CD Audio Play) CAUTION! NOTE: The ignition switch must be in the ON or ACC position to operate the radio. This CD player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism.
UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button (CD MODE for CD Audio Play) Press the right side of the SEEK button for the next selection on the CD. Press the left side of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. MUTE Button (CD MODE for CD Audio Play) Press the MUTE button to cancel the sound from the speakers. 9MUTE9 will be displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL Radio display will show 9EJECTING DISC9 when the disc is being ejected and prompt the user to remove the disc. Press and hold the LOAD/ EJT button for 5 seconds and all CDs will be ejected from the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not removed, the radio will continue to play the non-removed CD.
UNDERSTANDING YOUR INSTRUMENT PANEL RND/PTY Button (Random Play Button) (CD MODE for CD Audio Play) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track. Press and hold the FF button to fast forward through the tracks. Release the FF button to stop the fast forward feature.
UNDERSTANDING YOUR INSTRUMENT PANEL The radio uses the following limits for file systems: • Maximum number of directory levels: 15 • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator 9.9 and a 3-character extension) • Level 2: 31 (including a separator 9.9 and a 3-character extension) Multisession disc formats are supported by the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 Sampling Frequency (kHz) 48, 44.1, 32 24, 22.05, 16 Bit rate (kbps) 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 ID3 Tag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported.
UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (CD Mode for MP3 Audio Play) SEEK Button (CD Mode for MP3 Play) Pressing the right side of the SEEK button plays the next MP3 File. Pressing the left side of the SEEK button plays the beginning of the MP3 file. Pressing the button within the first ten seconds plays the previous file.
UNDERSTANDING YOUR INSTRUMENT PANEL MSG or INFO Button (CD Mode for MP3 Play) Press and MSG or INFO button while playing MP3 disc. The radio scrolls through the following TAG information: Song Title, Artist, File Name, and Folder Name (if available). Press the MSG or INFO button once more to return to 9elapsed time9 priority mode. Press and hold the MSG or INFO button while in the message display priority mode or elapsed time display priority mode will display the song title for each file.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. Operating Instructions - Video Entertainment System (VESt) (If Equipped) Refer to separate Video Entertainment System (VESt) Guide. SATELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius™ Satellite Radio.
UNDERSTANDING YOUR INSTRUMENT PANEL ESN/SID Access With REF Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and Time buttons simultaneously for 3 seconds. The first four digits of the twelve-digit ESN/SID number will be displayed. Press the SEEK UP button to display the next four digits. Continue to press the SEEK UP button until all twelve ESN/SID digits have been displayed. The SEEK DOWN will page down until the first four digits are displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL These radios will also display the current station name and program type. For more information such as song title and artist press the MSG or INFO button. A CD or tape may remain in the radio while in the Satellite radio mode. Selecting a Channel Press and release the SEEK or TUNE knob to search for the next channel. Press the top of the button to search up and the bottom of the button to search down.
UNDERSTANDING YOUR INSTRUMENT PANEL PTY Button (SCAN( When the desired program type is obtained, press the 9SCAN9 button within five seconds. The radio will play 7 seconds of the selected channel before moving to the next channel of the selected program type. Press the 9SCAN9 button a second time to stop the search. NOTE: Pressing the 9SEEK9 or 9SCAN9 button while performing a music type scan will change the channel by one and stop the search.
UNDERSTANDING YOUR INSTRUMENT PANEL • Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage. CD/DVD DISC MAINTENANCE To keep the CD/DVD discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS Climate Controls The Climate Control System allows you to balance the temperature, amount, and direction of air circulating throughout the vehicle. The controls are located on the instrument panel, below the radio. Climate Controls 269 The air conditioning system of your vehicle contains R-134a, a refrigerant that does not deplete the ozone layer in the upper atmosphere.
UNDERSTANDING YOUR INSTRUMENT PANEL Mode Control (Air Direction) The mode control allows you to choose from several patterns of air distribution. You can select either a primary mode, as identified by the symbols, or a blend of two of these modes. The closer the control is to a particular mode, the more air distribution you receive from that mode. Bi-Level Air is directed through the panel and floor outlets. Panel Air is directed through the outlets in the instrument panel.
UNDERSTANDING YOUR INSTRUMENT PANEL Defrost Air is directed through the windshield and side window demist outlets. Use this mode with maximum fan and temperature settings for best windshield and side window defrosting. NOTE: The air conditioning compressor operates in both Mix and Defrost or a blend of these modes even if the A/C button has not been pressed and the indicator lamp is off. This dehumidifies the air to help dry the windshield. To improve fuel economy, use these modes only when necessary.
UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control Air Conditioning Use this control to regulate the temperature of the air inside the passenger compartment. The blue area of the scale indicates cooler temperatures while the red area indicates warmer temperatures. Use this button to engage the Air Conditioning.
UNDERSTANDING YOUR INSTRUMENT PANEL Circulation Control Use this button to choose between outside air intake or recirculation of the air inside the vehicle. A lamp will illuminate when you are in recirculate mode. Only use the recirculate mode to temporarily block out any outside odors, smoke, or dust and to cool the interior rapidly upon initial start up in very hot or humid weather. 273 NOTE: Continuous use of the recirculate mode may make the inside air stuffy and window fogging may occur.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips
UNDERSTANDING YOUR INSTRUMENT PANEL 275 Window Fogging Vehicle side windows tend to fog on the inside in mild rainy or humid weather. To clear the windows, use the A/C, PANEL and blower controls. Direct the panel outlets toward the side windows. Do not use recirculate without A/C for long periods as fogging may occur.
UNDERSTANDING YOUR INSTRUMENT PANEL Side Window Demisters A side window demister outlet is at each end of the instrument panel. These nonadjustable outlets direct air toward the side windows when the system is in either the FLOOR, MIX, or DEFROST mode. The air is directed at the area of the windows through which you view the outside mirrors.
STARTING AND OPERATING CONTENTS m Starting Procedures . . . . . . . . . . . . . . . . . . . . . 280 m Automatic Transaxle — If Equipped . . . . . . . . . 283 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . . 280 ▫ Brake/Transmission Interlock System . . . . . . . 284 ▫ Manual Transaxle . . . . . . . . . . . . . . . . . . . . . 281 ▫ Automatic Transaxle Ignition Interlock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284 ▫ Normal Starting . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING ▫ AutoStick General Information . . . . . . . . . . . . 289 ▫ Tire Loading And Tire Pressure . . . . . . . . . . . 306 m Manual Transaxle Operation . . . . . . . . . . . . . . . 290 m Tires — General Information . . . . . . . . . . . . . . . 310 ▫ 2.4 Liter Turbo— If Equipped . . . . . . . . . . . . . 291 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . 310 ▫ Recommended Shift Speeds . . . . . . . . . . . . . . 292 ▫ Tire Inflation Pressures . . . . . . .
STARTING AND OPERATING 279 m Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 320 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . . 328 m Tire Rotation Recommendations . . . . . . . . . . . . 320 m Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . . . 328 m Fuel Requirements . . . . . . . . . . . . . . . . . . . . . . 321 m Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . 328 ▫ 2.4L Standard Engine And 2.4L Standard Turbo Engine . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle.
STARTING AND OPERATING Manual Transaxle Before starting the engine fully apply the parking brake, press the clutch pedal to the floor and place the gear selector in NEUTRAL. NOTE: The engine will not start unless the clutch pedal is pressed to the floor. Normal Starting Normal Starting of either a cold or a warm engine does not require pumping or depressing the accelerator pedal. Simply turn the ignition switch to the “START’” position and release when the engine starts.
STARTING AND OPERATING If Engine Fails to Start If the engine fails to start after you have followed the “NORMAL STARTING” procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there. Crank the engine for no more than 15 seconds. This should clear any excess fuel in case the engine is flooded. Leave the ignition key in the ON position, release the accelerator pedal and repeat the “NORMAL STARTING” procedure.
STARTING AND OPERATING 283 TURBOCHARGER (COOL DOWN( CHART Driving Conditions Idle Time (in minutes) Before Shut Down Normal Driving Not required. Aggressive Driving or Heavily Loaded 3 Trailer Tow 5 AUTOMATIC TRANSAXLE — IF EQUIPPED CAUTION! • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed.
STARTING AND OPERATING WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
STARTING AND OPERATING Four Speed Automatic Transaxle The electronically controlled transaxle provides a precise shift schedule. The transaxle electronics are self calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few shift cycles. Reset Mode The transaxle is monitored electronically for abnormal conditions.
STARTING AND OPERATING brake when leaving the vehicle in this range. Always apply the parking brake first, and then place the selector in P (Park) position. The following indicators should be used to ensure that you have engaged the transmission shift lever into the P (Park) position: WARNING! • When shifting into P (Park), depress the button on the shift lever and firmly move the lever all the way forward until it stops. Unintended movement of a vehicle could injure those in and near the vehicle.
STARTING AND OPERATING CAUTION! Before moving the shift lever out of P (Park), you must turn the ignition from LOCK to ON so the steering wheel and shift lever are released. Otherwise, damage to the steering column or shifter could result. “R” Reverse Shift into this range only after the vehicle has come to a complete stop. “N” Neutral Engine may be started in this range. “D” Overdrive This range should be used for most city and highway driving.
STARTING AND OPERATING “1” Low This range should be used for maximum engine braking when descending steep grades. In this range, up shifts will occur only to prevent engine over speed while down shifts from 2nd to first will occur as early as possible. AUTOSTICK — IF EQUIPPED Autostick is a driver-interactive transmission that offers manual gear shifting capability to provide you with more control.
STARTING AND OPERATING Autostick General Information • The transmission will automatically upshift from first to second gear and from second to third gear when engine speed reaches about 6300 RPM. • Downshifts from third to second gear above 74 mph (119 km/h) and from second to first gear above 41 mph (66 km/h) will be ignored. • You can start out in first, second, or third gear. Shifting into fourth gear can occur only after vehicle speed reaches 15 mph (24 km/h).
STARTING AND OPERATING MANUAL TRANSAXLE OPERATION WARNING! You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied. The parking brake should always be applied when the driver is not in the vehicle, especially on an incline. Fully depress the clutch pedal before you shift gears. As you release the clutch pedal, lightly depress the accelerator pedal. 5 – Speed Shift Pattern Non-Turbo Use each gear in numerical order - do not skip a gear.
STARTING AND OPERATING For most city driving you will find it easier to use only the lower gears. For steady highway driving with light accelerations, 5th gear is recommended. 291 2.4 Liter Turbo— If Equipped Never drive with your foot resting on the clutch pedal, or try to hold the vehicle on a hill with the clutch pedal partially engaged. This will cause abnormal wear on the clutch. Never shift into REVERSE until the vehicle has come to a complete stop.
STARTING AND OPERATING the shifter lever all the way to the right to avoid accidentally selecting THIRD gear. Also, use care when selecting FIRST gear to avoid accidentally selecting REVERSE. Recommended Shift Speeds To use your manual transaxle for optimal fuel economy, it should be upshifted as listed in table 1. When moving the shifter lever into REVERSE press the lever to the left until the resistance is overcome.
STARTING AND OPERATING For improved performance, your manual transaxle may be upshifted up to the maximum speeds listed in table 2 (within legal speed limits). Table 2-Manual Transaxle Maximum Performance Shift Speeds In mph (km/h) Engine 1 to 2 2 to 3 3 to 4 4 to 5 Size 30 60 85 115 2.4L (48) (97) (136) (185) If you exceed these speeds, you may notice the engine cut in and out. This is caused by an electronic limiter in the engine computer. The engine will run normally when you reduce engine speed.
STARTING AND OPERATING PARKING BRAKE When the parking brake is applied with the ignition on, the Brake Light in the instrument cluster will come on. NOTE: This light only shows that the parking brake is on. It does not show the degree of brake application. slightly on the lever, then depress the button on the end of the lever and push the lever fully down toward the floor. NOTE: The parking brake lever will not release unless the lever is pulled up slightly past its applied position.
STARTING AND OPERATING When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the automatic transaxle locking mechanism may make it difficult to move the selector out of Park. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on a uphill grade. You should always apply the parking brake before leaving the vehicle. 295 WARNING! Never leave children alone in a vehicle.
STARTING AND OPERATING WARNING! WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency. Driving a vehicle with the brake light on is dangerous. A significant decrease in braking performance or vehicle stability during braking may occur.
STARTING AND OPERATING 297 WARNING! WARNING! Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
STARTING AND OPERATING The ABS light monitors the Anti-Lock Brake System. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or comes on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on.
STARTING AND OPERATING • and a slight drop or fall away of the brake pedal at the end of the stop. These are all normal characteristics of ABS. WARNING! The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals.
STARTING AND OPERATING WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! TRACTION CONTROL SYSTEM — IF EQUIPPED The Traction Control System (TCS) will improve acceleration and steering on slippery surfaces by reducing tire spin. The system reduces wheel slip and maintains traction at the driving (front) wheels by engaging the brake on the wheel that is losing traction.
STARTING AND OPERATING The system is always in the “ON” mode unless: • The TCS OFF switch has been used to turn the system off; • There is a Anti-Lock Brake System malfunction; • There is a Traction Control System malfunction; • The system has been automatically deactivated to prevent damage to the brake system due to overheated brake temperatures. NOTE: Extended heavy use of Traction Control may cause the system to deactivate and turn on the TCS indicator lamp located in the instrument cluster.
STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter 9P9 is absent from this tire size designation. Example: 215/65R15 96H • LT (Light Truck)-Metric tire sizing is based on U.S. design standards.
STARTING AND OPERATING 303 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards (....blank....( = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions (i.e. tire pressure, vehicle loading, road conditions, and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. 305 Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar.
STARTING AND OPERATING 307 Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information” placard and in the “Vehicle Loading” section of this manual.
STARTING AND OPERATING 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
STARTING AND OPERATING 309 5
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation, also increases tire rolling resistance and results in higher fuel consumption. 311 maximum loaded vehicle condition. These pressure conditions will be found in the “Supplemental Tire Pressure Information” section of this manual. 3.
STARTING AND OPERATING check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. CAUTION! Tire pressures change by approximately 1 psi (7 kPa) per 12 °F (7 °C) of air temperature change.
STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high-speed vehicle operation.
STARTING AND OPERATING Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Always use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels). Never combine them with other types of tires. Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
STARTING AND OPERATING Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result.
STARTING AND OPERATING WARNING! WARNING! The limited use spare tires are for emergency use only. Installation of this limited use spare tire affects vehicle handling. With this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly. Replace (or repair) the original tire at the first opportunity and reinstall it on your vehicle.
STARTING AND OPERATING 317 Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Many states have laws requiring tire replacement at this point.
STARTING AND OPERATING Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
STARTING AND OPERATING CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. Alignment And Balance Poor suspension alignment may result in: • Fast tire wear. • Uneven tire wear, such as feathering and one-sided wear. • Vehicle pull to right or left. Tires may also cause the vehicle to pull to the left or right. Alignment will not correct this condition. See your dealer for proper diagnosis.
STARTING AND OPERATING SNOW TIRES Some areas of the country require the use of snow tires during winter. Standard tires are of the all season type and satisfy this requirement as indicated by the M+S designation on the tire sidewall. If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of 4, failure to do so may adversely affect the safety and handling of your vehicle.
STARTING AND OPERATING wear should be corrected before rotating. The suggested rotation method is the “forward-cross” shown in the diagram. 321 FUEL REQUIREMENTS 2.4L Standard Engine and 2.4L Standard Turbo Engine Your vehicle is designed to meet all emission regulations and provide excellent fuel economy when using high quality regular unleaded gasoline with an octane rating of 87. The use of premium gasoline is not recommended.
STARTING AND OPERATING high quality unleaded gasoline having an octane rating of 91. The purchase of higher octane is not required. The use of high quality unleaded gasoline having an octane rating of 91 is recommended but not required. High quality unleaded gasoline having a minumum octane rating of 87 may safely be used for your vehicle. Use of these lower octane gasolines, however, may result in reduced acceleration performance. Light spark knock at low engine speeds is not harmful to your engine.
STARTING AND OPERATING Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as 10% ethanol, MTBE, and ETBE. Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle. CAUTION! DO NOT use gasolines containing Methanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components.
STARTING AND OPERATING Materials Added to Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in additional cost. Therefore you should not have to add anything to the fuel. • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat.
STARTING AND OPERATING Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
STARTING AND OPERATING NOTE: When removing the fuel filler cap, lay the cap tether in the hook, located on the fuel filler cap door reinforcement. CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. CAUTION! A poorly fitting gas cap may cause the Malfunction Indicator Light to turn on.
STARTING AND OPERATING CAUTION! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full. 327 NOTE: Tighten the gas cap about 1/4 turn until you hear one click. This is an indication that cap is properly tightened. If the gas cap is not tighten properly, the Malfunction Indicator Light will come on. Be sure the gas cap is tightened every time the vehicle is refueled.
STARTING AND OPERATING Loose Fuel Filler Cap Message If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “gASCAP” message will be displayed in the Odometer/ Trip Odometer in the instrument cluster. Refer to “Instrument Cluster Description” in Section 4 of this manual. Tighten the fuel filler cap properly and press the odometer/trip odometer reset button to turn the message off.
STARTING AND OPERATING Common Towing Definitions The following trailer towing related definitions will assist you in understanding the following information: Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight. The total load must be limited so that you do not exceed the GVWR.
STARTING AND OPERATING Tongue Weight (TW) The downward force exerted on the hitch ball by the trailer. In most cases it should not be less than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle. Frontal Area The maximum height and maximum width of the front of a trailer.
STARTING AND OPERATING WARNING! An improperly adjusted Weight Distributing Hitch system may reduce handling, stability, braking performance, and could result in an accident. Weight Distributing Systems may not be compatible with Surge Brake Couplers. Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.
STARTING AND OPERATING Trailer Hitch Classification Class Max. GTW (Gross Trailer Wt.) Class I - Light Duty 2,000 lbs (907 kg) Class II - Medium 3,500 lbs (1 587 kg) Duty Class III - Heavy Duty 5,000 lbs (2 268 kg) Class IV - Extra 10,000 lbs (4 540 kg) Heavy Duty All trailer hitches should be professionally installed on your vehicle. Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain.
STARTING AND OPERATING Engine/Transmission Frontal Area Max. GTW (Gross Trailer Wt.) 2.4L N/A and 2.4L 20 Sq. Ft Turbo/Automatic* 2.4L N/A and 2.4L 20 Sq. Ft. Turbo/Manual* * N/A (Naturally Aspirated) Refer to local laws for maximum trailer towing speeds. Note 1 – The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the Tire and Loading Information placard.
STARTING AND OPERATING Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle.
STARTING AND OPERATING 335 CAUTION! WARNING! • Avoid towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may damage your vehicle. • During the first 500 miles (805 km) of trailer towing, limit your speed to 50 mph (80 km/h). Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel.
STARTING AND OPERATING • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle automatic transmission in P for Park. Always, block or 9chock9 the trailer wheels. • GCWR must not be exceeded.
STARTING AND OPERATING − When replacing tires refer to the Tires–General Information section of this manual on Replacement Tires for proper tire replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s GVWR and GAWR limits. 337 − Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg).
STARTING AND OPERATING WARNING! NOTE: Do not cut or splice wiring into the vehicles wiring harness. Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. Towing any trailer will increase your stopping distance. When towing you should allow for additional space between your vehicle and the vehicle in front of you.
STARTING AND OPERATING 339 Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance and extend transmission life by reducing excessive shifting and heat build up. This action will also provide better engine braking.
STARTING AND OPERATING Towing Tips — Electronic Speed Control (If Equipped) − Air Conditioning Turn off temporarily. − Don’t use in hilly terrain or with heavy loads. − refer to Cooling System Operating information in the Maintenance section of this manual for more information. − When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed.
WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 342 m Driving On Slippery Surfaces . . . . . . . . . . . . . . 352 m If Your Engine Overheats . . . . . . . . . . . . . . . . . 342 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . . 352 m Jacking And Tire Changing . . . . . . . . . . . . . . . . 344 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and the vehicle locked. NOTE: With extended use, the flasher may wear down your battery. Hazard Warning Switch The flasher switch is located on the instrument panel, below the radio. Depress the switch and both cluster indicators and all front and rear directional signals will flash.
WHAT TO DO IN EMERGENCIES the normal range. If the pointer remains on the H (red) mark for more than a minute, turn the engine off immediately and call for service. NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat.
WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, refer to Section 7, Maintenance, of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous.
WHAT TO DO IN EMERGENCIES Jack Location The jack and jack-handle are stowed behind the right rear side trim panel in the cargo area. 345 Spare Tire Stowage The compact spare tire is stowed under the rear of the vehicle by means of a hook/basket mechanism. To remove or stow the compact spare, use the jack handle to rotate the “spare tire drive” nut. The nut is located under the rear scuff plate at the right rear of the cargo area, just inside the liftgate opening.
WHAT TO DO IN EMERGENCIES CAUTION! The hook is designed for use with the jack handle only. Use of an air wrench or other power tools is not recommended and can damage the winch. Preparations For Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, set the parking brake and place the gear selector in PARK (automatic transaxle) or REVERSE (manual transaxle). Turn OFF the ignition.
WHAT TO DO IN EMERGENCIES WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • Turn on the Hazard Warning Flasher. • Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if changing the right front tire, block the left rear wheel. • Passengers should not remain in the vehicle while the vehicle is being jacked.
WHAT TO DO IN EMERGENCIES 3. There are two front jacking locations on each side of the body and rear jacking locations located on the trailing arm bracket under the triangular cut out symbol. Turn the jack screw to the right until the jack head is properly engaged with the lift area closest to the wheel to be changed. Do not raise the vehicle until you are sure the jack is securely engaged. 4. Raise the vehicle by turning the jack screw to the right, using the swivel wrench.
WHAT TO DO IN EMERGENCIES 349 nuts toward the wheel. Lightly tighten the nuts. To avoid the risk of forcing the vehicle off the jack, do not tighten the nuts fully until the vehicle has been lowered. 100 ft. lbs (135 N·m). If you doubt that you have tightened the nuts correctly, have them checked with a torque wrench by your dealer or at a service station. WARNING! 8. Remove the wheel blocks and lower the jack until it is free. Stow the lug wrench, and jack in their designated location.
WHAT TO DO IN EMERGENCIES WARNING! WARNING! A loose tire thrown forward in a collision or hard stop could injure the occupants in the vehicle. Have the deflated (flat) tire repaired or replaced immediately. Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
WHAT TO DO IN EMERGENCIES 2. When boosting from a battery in another vehicle, park that vehicle within booster cable reach but without letting the vehicles touch. Set parking brake, place automatic transaxle in PARK (manual transaxle in NEUTRAL) and turn ignition to OFF for both vehicles. 3. Turn off the heater, radio and all unnecessary electrical loads. 4. Connect one end of a jumper cable to the positive terminal of the booster battery.
WHAT TO DO IN EMERGENCIES 6. If the vehicle is equipped with Sentry Key Immobilizer, turn the ignition switch to the ON position for 3 seconds before moving the ignition switch to the START position. 7. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 8. When removing the jumper cables, reverse the sequence exactly. Be careful of the moving belts and fan.
WHAT TO DO IN EMERGENCIES 2. Slow down if road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain enough distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop. FREEING A STUCK VEHICLE NOTE: If your vehicle is equipped with Traction Control, turn the system OFF before attempting to “rock” the vehicle.
WHAT TO DO IN EMERGENCIES CAUTION! Racing the engine or spinning the wheels too fast may lead to transaxle overheating and failure. It can also damage the tires. Do not spin the wheels above 35 mph (55km/h).
WHAT TO DO IN EMERGENCIES All Transaxles CAUTION! If the vehicle being towed requires steering, the ignition switch must be in the ACCESSORY position, not in the LOCK positions. Do not attempt to use sling type equipment when towing. When securing vehicle to flat bed truck, do not attach to front or rear suspension components. Damage to your vehicle may result from improper towing. If it is necessary to use the accessories while being towed (wipers, defrosters, etc.
WHAT TO DO IN EMERGENCIES CONVERTIBLE TOP MANUAL OVERRIDE If your vehicle is experiencing electrical failure (low battery, etc.) and it is necessary to raise the convertible top, perform the following steps: 1. Locate the convertible top motor bypass screw, which is found in the trunk under the convertible top storage area. 2. Turn the screw counterclockwise until the screw stops. This will relieve the hydraulic pressure and allow the convertible top to be raised manually. Bleeder Screw 3.
WHAT TO DO IN EMERGENCIES 357 6. Raise the handle into the stowed position. 7. Close the convertible top motor bypass screw by turning the screw clockwise until it stops. Tighten the screw securely. NOTE: Failure to tighten the bypass screw securely can cause convertible top operating concerns.
MAINTAINING YOUR VEHICLE CONTENTS m 2.4L Turbo Engine Compartment . . . . . . . . . . . . 362 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 368 m 2.4L Engine Compartment . . . . . . . . . . . . . . . . 363 ▫ Drive Belts — Check Condition And Tension . . 372 m Onboard Diagnostic System — OBD II . . . . . . . . 364 ▫ Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . 372 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . . 364 ▫ Ignition Wiring System . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Maintenance-Free Battery . . . . . . . . . . . . . . . . 375 ▫ Manual Transaxle . . . . . . . . . . . . . . . . . . . . . 393 ▫ Air Conditioner Maintenance . . . . . . . . . . . . . 377 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . 393 ▫ Power Steering — Fluid Check . . . . . . . . . . . . 378 ▫ Front Suspension Ball Joints . . . . . . . . . . . . . . 379 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 361 ▫ Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . 406 ▫ Center High Mounted Stop Light . . . . . . . . . . 409 ▫ Front Park/Turn Signal/Side Marker Lights . . 407 m Fluids And Capacities . . . . . . . . . . . . . . . . . . . 410 ▫ Front Fog Lights — If Equipped . . . . . . . . . . . 407 m Fluids, Lubricants And Genuine Parts . . . . . . . . 411 ▫ Tail/Stop, And Rear Turn Signal Lights . . . . . . 407 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 2.
MAINTAINING YOUR VEHICLE 363 2.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 365 a 9clicking9 sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem will turn the MIL light off.
MAINTAINING YOUR VEHICLE 4. As soon as you turn your key to the ON position, you will see your MIL symbol come on as part of a normal bulb check. 5. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b.
MAINTAINING YOUR VEHICLE DEALER SERVICE Your dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
MAINTAINING YOUR VEHICLE could adversely affect the engine or vehicle performance. These items should be inspected if a malfunction is observed or suspected. Engine Oil Checking Oil Level To assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop.
MAINTAINING YOUR VEHICLE CAUTION! Overfilling the crankcase as indicated by an oil level above the “Max” mark on the engine oil dipstick will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Change Engine Oil Road conditions and your kind of driving affects the interval at which your oil should be changed. Check the following list to decide if any apply to you. • Day and night temperatures are below 32°F (0°C).
MAINTAINING YOUR VEHICLE change your engine oil at every interval shown on schedule “A”—NON TURBO in the maintenance schedule section of this manual. If none of these apply to you, and your vehicle is equipped with a Turbo Charged Engine change your engine oil at every interval shown on schedule “A”—TURBO in the maintenance schedule section of this manual. NOTE: Under no circumstances should oil change intervals exceed 6000 miles (10 000 km) or 6 months whichever comes first.
MAINTAINING YOUR VEHICLE Lubricants which do not have both, the engine oil certification mark and the correct SAE viscosity grade number should not be used. Synthetic Engine Oils There are a number of engine oils being promoted as either synthetic or semi-synthetic. If you chose to use such a product, use only those oils that are American Petroleum Institute (API) Certified and have the recommended SAE viscosity grade. Follow the maintenance schedule that describes your driving type.
MAINTAINING YOUR VEHICLE Drive Belts — Check Condition and Tension At the mileage shown in the maintenance schedules, check all drive belts for condition and proper tension. Improper belt tension can cause belt slippage and failure. Inspect the drive belts for evidence of cuts, cracks, or glazing and replace them if there is any sign of damage which could result in belt failure. If adjustment is required, see your authorized dealer for service.
MAINTAINING YOUR VEHICLE 373 CAUTION! WARNING! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle.
MAINTAINING YOUR VEHICLE To minimize the possibility of catalyst damage: • Do not try to start the engine by pushing or towing the vehicle. Crankcase Emission Control System Proper operation of this system depends on freedom from sticking or plugging due to deposits. As vehicle mileage builds up, the PCV valve and passages may accumulate deposits. If a valve is not working properly, replace it with a new valve.
MAINTAINING YOUR VEHICLE Air Cleaner Element (Filter) Under normal driving conditions, replace the filter at the intervals shown on Schedule “A”. If, however, you drive the vehicle frequently under dusty or severe conditions, the filter element should be inspected periodically and replaced if necessary at the intervals shown on Schedule “B”. NOTE: For vehicles with a Turbo engine, a small amount of oil accumulation in the air cleaner box is normal. The amount will depend on driving style.
MAINTAINING YOUR VEHICLE CAUTION! WARNING! When servicing the battery, always reinstall the battery thermowrap. The thermowrap provides battery heat protection and will extend overall battery life. Failure to reinstall the thermowrap can result in evaporative loss of the battery fluid. Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps.
MAINTAINING YOUR VEHICLE CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion. Apply grease to posts and clamps after tightening.
MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information book for further warranty information. • The air conditioning system contains refrigerant under high pressure.
MAINTAINING YOUR VEHICLE WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Fluids, Lubricants, and Genuine Parts for correct fluid types.
MAINTAINING YOUR VEHICLE Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non abrasive cleaner or use the washer solvent. This will remove accumulations of salt, waxes or road film and help reduce streaking and smearing. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield.
MAINTAINING YOUR VEHICLE when the underside or rear of the vehicle is damaged; have a competent technician inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for an oil change or lubrication. Replace as required. WARNING! Exhaust gases can injure or kill.
MAINTAINING YOUR VEHICLE Coolant Checks Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser.
MAINTAINING YOUR VEHICLE CAUTION! Mixing of coolants other than specified HOAT engine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible. Do not use plain water alone or alcohol base engine coolant (antifreeze) products.
MAINTAINING YOUR VEHICLE The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated. NOTE: Mixing coolant types will decrease the life of the engine coolant and will require more frequent coolant changes.
MAINTAINING YOUR VEHICLE do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately. Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate.
MAINTAINING YOUR VEHICLE • Check coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze needs to be added, contents of coolant recovery bottle must also be protected against freezing. • If frequent coolant additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks.
MAINTAINING YOUR VEHICLE Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present. Components should be replaced immediately if there is any evidence of degradation that could cause failure. Fuel System Connections Electronic Fuel Injection high pressure fuel systems are designed with tubes and special connects, connections and clamps which have unique material characteristics to provide adequate sealing and resist attack by deteriorated gasoline.
MAINTAINING YOUR VEHICLE evidence of heat and mechanical damage. Hard and brittle rubber, cracking, tears, cuts, abrasions, and excessive swelling suggest deterioration of the rubber. Particular attention should be made to examining those hose surfaces nearest to high heat sources, such as the exhaust manifold. NOTE: Inspection of brake hoses should be done whenever the brake system is serviced and at every engine oil change.
MAINTAINING YOUR VEHICLE fluid reservoir. Fluid level can be expected to fall as the brake pads wear. Brake fluid level should be checked when pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. NOTE: If your vehicle is equipped with a Manual transaxle , the Brake Fluid Reservoir supplies fluid to both the Brake System and the Clutch Release System. The two systems are separated in the reservoir and a leak in one system will not affect the other system.
MAINTAINING YOUR VEHICLE WARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. refer to Fluids, Lubricants and Genuine Parts for correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid. CAUTION! Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter.
MAINTAINING YOUR VEHICLE Fluid Level Check The fluid level in the automatic transaxle should be checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly reduce the life of the transaxle and of the fluid. Procedure For Checking Fluid Level To properly check the automatic transaxle fluid level, the following procedure must be used: 1. The vehicle must be on level ground. 2. The engine should be running at curb idle speed for at minimum of 60 seconds. 391 5.
MAINTAINING YOUR VEHICLE CAUTION! Do not overfill. Dirt and water in the transaxle can cause serious damage. To prevent dirt and water from entering the transaxle after checking or replenishing fluid, make certain that the dipstick cap is seated properly. Fluid And Filter Changes Automatic transmission fluid and filter should be changed as follows: Maintenance schedule “A”—Non Turbo Charged Engines – No change necessary. Maintenance schedule “A”—Turbo Charged Engines – No change necessary.
MAINTAINING YOUR VEHICLE Manual Transaxle Lubricant Selection Use only manufacturers recommended transmission fluid. Refer to Fluids, Lubricants and Genuine Parts for the correct fluid type. Fluid Level Check Check the fluid level by removing the fill plug. The fluid level should be between the bottom of the fill hole and a point not more that 3/16” (4.7 mm) below the bottom of the hole. Add fluid, if necessary, to maintain the proper level.
MAINTAINING YOUR VEHICLE The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar. • Salt in the air near sea coast localities.
MAINTAINING YOUR VEHICLE CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. 395 • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as possible.
MAINTAINING YOUR VEHICLE heavy soil, use Mopar Wheel Cleaner or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush or metal polishes. Only Mopar cleaners are recommended. Do not use oven cleaner. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish.
MAINTAINING YOUR VEHICLE soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, detergents, or ammonia based cleaners to clean your leather upholstery. Application of a leather conditioner is not required to maintain the original condition. WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm.
MAINTAINING YOUR VEHICLE Instrument Panel Cover The instrument panel cover has a low glare surface which minimizes reflections in the windshield. Do not use protectants or other products which may cause undesirable reflections. Use soap and warm water to restore the low glare surface. Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1.
MAINTAINING YOUR VEHICLE Washing Hand washing is highly recommended. Automatic car washing equipment can damage the top material. If you must use an automatic car wash, soft cloth systems are preferred. CAUTION! Avoid high pressure car washes, as they can damage the top material. Also, increased water pressure may force water past the weather strips. General Cleaning Careful vacuuming of the top before washing is helpful in removing dust and other foreign particles.
MAINTAINING YOUR VEHICLE Cloth Top Additional Cleaning Procedure For additional cleaning assistance in removing stubborn stains, apply Mopar Convertible Cloth Top Cleaner (part number 05012245AA) to the complete stain, extending 2 inches (50 mm) beyond the stain. With a soft bristle brush, scrub in all directions over the stain. Avoid heavy scrubbing. Rinse the area with warm water. If the stain is still apparent, repeat the cleaning procedure.
MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 3 10 Amp Red 4 10 Amp Red 5 20 Amp Yellow 6 10 Amp Red Integrated Power Module Location Cavity Cartridge Mini Fuse Fuse 1 40 Amp Green 2 20 Amp Yellow Description Power Top Feed — Convertible Only AWD ECU Feed 7 30 Amp Green 30 Amp Green 8 9 10 40 Amp Green Description CHMSL Brake Switch Feed Ignition Switch Feed Trailer Tow IOD Sw/Pwr Mir/ Ocm Steering Cntrl Sdar/Hfm IOD Sense1 IOD Sense2 Power Seats 20 Amp Yellow 401 CCN, Power Locks 7
MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 11 15 Amp Lt Blue 12 20 Amp Yellow 13 20 Amp Yellow 14 10 Amp Red 15 50 Amp Red 16 15 Amp Lt. Blue 17 10 Amp Red 18 40 Amp Green Description Power Outlet Ign Run/Acc Inverter Pwr run/Acc Outlet RR IOD CCN/ Interior Lighting RAD Fan Relay Battery Feed IGN Run/Acc Cigar Ltr/Sunroof IOD Feed CVT Mod/ Mod_Wcm ASD Relay Contact PWR Feed Cavity Cartridge Mini Fuse Fuse 19 20 Amp Yelow 20 15 Amp Lt. Blue 21 10 Amp Red 22 10 Amp Red 23 15 Amp Lt.
MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 27 10 Amp Red 28 10 Amp Red 29 30 20 Amp Yellow 31 10 Amp Red 32 30 Amp Pink 33 10 Amp Red 34 30 Amp Pink Description IGN RUN Only ORC Feed IGN RUN ORC/OCM Feed EMPTY Heated Seats Headlamp Washer Relay Control ENG ASD Control Feed 1 ABS MOD/J1962 Conn/PCM ABS Valve Feed Cavity Cartridge Mini Fuse Fuse 35 40 Amp Green 36 30 Amp Pink 37 25 Amp Natural 403 Description ABS Pump Feed Headlamp Washer Control Spare 7
MAINTAINING YOUR VEHICLE CAUTION! • When installing the Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
MAINTAINING YOUR VEHICLE REPLACEMENT BULBS LIGHT BULBS — Inside Bulb No. Center Console Floor Lamp . . . . . . . . . . . . . . . . . T37 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 6233137 Console Gear Selector . . . . . . . . . . . . . . . . . . . PC194 Dome Light (sedan) . . . . . . . . . . . . . . . . . . . . . . T579 Dome Light / Sport Bar Lights (convertible) . . . . T904 Instrument Cluster Illumination . . . . . . . . . . . . . . 74 Overhead Reading Light (Overhead Console) . . .
MAINTAINING YOUR VEHICLE BULB REPLACEMENT Headlights CAUTION! Do not touch the new headlight bulb with your fingers. Oil contamination will severely shorten bulb life. 1. Remove the headlight access cover splash shield, located in the front wheel well opening. 2. Disconnect the electrical connector. 3. Rotate the socket to the left one quarter turn and replace the bulb.
MAINTAINING YOUR VEHICLE 407 Front Park/Turn Signal/Side Marker Lights Front Fog Lights — If Equipped 1. Remove the headlight access cover splash shield, located in the front wheel well opening. 1. Remove the fasteners attaching the lower splash shield to gain access to the fog light. 2. Rotate the socket to the left one quarter turn to replace and replace the bulb. 2. Twist and remove the bulb from the fog light housing. 3. Disconnect the electrical connector and replace bulb.
MAINTAINING YOUR VEHICLE 2. Twist the bulb socket 1/4 turn to remove it from the housing. Back Up Lights Removing Backup Light Bulbs 3. Pull the bulb out of the socket and replace. 1. To remove the backup lamp, you must take a fiber stick and slide it along the inboard side of the lamp and compress a spring clip to allow it to partially 9pop9 out to the secondary catch.
MAINTAINING YOUR VEHICLE 2. Fully compress the clip to get the lamp to come out completely. 3. Remove the socket from the housing. 4. Pull the bulb out of the socket and replace. 409 Center High Mounted Stop Light 1. Open the liftgate and remove the liftgate CHMSL cover. 2. Remove CHMSL lens from the housing by unlatching the two side latches. 3. Pull the bulb out of the socket and replace.
MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel (Approximate) Engine Oil-With Filter 2.4 Liter Engines (Use API Certified SAE 5W-30 Engine Oil). Cooling System * 2.4 Liter Engines (Mopart Antifreeze/Coolant 5 Year/100,000 Miles Formula), or equivalent. * Includes heater and coolant recovery bottle filled to MAX level. U.S. 15 Gallons Metric 56.7 Liters 5.0 qts 4.7 Liters 6.5 qts 6.
MAINTAINING YOUR VEHICLE 411 FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluids, Lubricants and Genuine Parts Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Use API Certified SAE 5W-30 Engine Oil. Refer to your engine oil filler cap for correct SAE grade meeting DaimlerChrysler Material Standard MS-6395. Non Turbo—Mopar 4105409AB or equiv.
MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Fluid. Manual Transmission Fluid. Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopart ATF+4 Automatic Transmission Fluid. Mopart ATF+4 Automatic Transmission Fluid. Mopart DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids or equivalent.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E m Emission Control System Maintenance . . . . . . . . 414 ▫ Schedule “A”—Non Turbo . . . . . . . . . . . . . . . 428 m Maintenance Schedule . . . . . . . . . . . . . . . . . . . 414 ▫ Schedule “A”—Turbo . . . . . . . . . . . . . . . . . . 433 C ▫ Schedule “B”—All Engines . . . . . . . . . . . . . .
M A I N T E N A N C E 414 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES • Taxi, police, or delivery service (commercial service).†L • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow schedule “B—All Engines” of the 9Maintenance Schedules9 section of this manual.
M 416 MAINTENANCE SCHEDULES A I At Each Stop for Fuel N T • Check the engine oil level about 5 minutes after a fully E warmed engine is shut off. Checking the oil level while N A the vehicle is on level ground will improve the accuN racy of the oil level reading. Add oil only when the C level is at or below the ADD or MIN mark. E S C H E D U L E S 8 • Check the windshield washer solvent and add if required. • Check all lights and all other electrical items for correct operation.
SCHEDULE “B”—ALL ENGINES SCHEDULE “B”—ALL ENGINES Follow schedule “B”—All Engines if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (100 000 km) if the vehicle is usually operated under one or more of the conditions marked with an L. Change the manual transaxle fluid every 48,000 miles (80 000 km) if the vehicle is usually operated under one or more of the conditions marked with an †.
M A I N T E N A N C E 418 SCHEDULE “B”—ALL ENGINES NOTE: IF ANY of these apply to you then flush and replace the engine coolant every 102,000 miles (170 000 km) or 60 months, whichever comes first, and follow schedule “B—All Engines” of the 9Maintenance Schedules9 section of this manual.
SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter, replace as necessary.* Inspect the Make-up air filter, replace as necessary.
M 420 SCHEDULE “B”—ALL ENGINES A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace as necessary.* Replace the Make-up air filter. Adjust the generator drive belt tension.
SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Change the brake fluid. If vehicle is used for trailer towing. Inspect the engine air cleaner filter, replace as necessary.* Change the manual transaxle fluid.† Inspect the Make-up air filter. Replace as necessary.
M 422 SCHEDULE “B”—ALL ENGINES A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Replace the Make-up air filter. Adjust the generator drive belt tension.
SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter and replace as necessary.* Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Inspect the Make-up air filter, replace as necessary. Adjust the generator drive belt tension.
M 424 SCHEDULE “B”—ALL ENGINES A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not reA placed at 3 months. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Change the brake fluid. If vehicle is used for trailer towing. Inspect the engine air cleaner filter and replace as necessary.* Change the manual transaxle fluid.† Replace the engine timing belt. * Flush and replace the engine coolant, if not replaced at 60 months.
SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. * Inspect the tie rod ends and boot seals. Replace the Make-up air filter. Adjust the generator drive belt tension. Change automatic transaxle fluid and filter.L Inspect the PCV valve and replace if necessary. *‡ Flush and replace the engine coolant at 120 months, if not replaced at 102,000 miles.
M 426 SCHEDULE “B”—ALL ENGINES A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not reA placed at 3 months. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Inspect the engine air cleaner filter and replace as necessary.
SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. * Replace the spark plugs. Change the manual transaxle fluid.† Replace the Make-up air filter. Inspect the PCV valve and replace if necessary. *‡ 138,000 (230 000) X * This maintenance is recommended by the manufacturer to the owner, but is not required to maintain the emissions warranty.
M 428 SCHEDULE “A”—NON TURBO A I SCHEDULE “A”—NON TURBO N T Miles E N (Kilometers) A [Months] N C Change engine oil and engine oil filter. E Rotate tires. S C H E D U L E S 8 Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the Make-up air filter.
SCHEDULE “A”—NON TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace, if necessary.* Flush and replace the engine coolant at 60 months, if not done at 102,000 miles. Replace the Make-up air filter. Adjust the generator drive belt tension.
M 430 SCHEDULE “A”—NON TURBO A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Replace the engine air cleaner filter. Replace the spark plugs. Replace the engine timing belt. * Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Replace the Make-up air filter. Adjust the generator drive belt tension.
SCHEDULE “A”—NON TURBO 431 M Miles 108,000 114,000 120,000 126,000 132,000 138,000 (Kilometers) (180 000) (190 000) (200 000) (210 000) (220 000) (230 000) [Months] [108] [114] [120] [126] [132] [138] Change engine oil and engine oil filter. X X X X X X Rotate tires. X X X X X X Inspect the PCV valve and replace if necessary. * ‡ X Replace the air cleaner filter. X Flush and replace the engine coolant at 120 X months, if not done at 102,000 miles. Replace the spark plugs and ignition cables.
M 432 SCHEDULE “A”—NON TURBO A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Inspect the PCV valve and replace if necessary. * ‡ S C H E D U L E S 8 Replace the air cleaner filter. * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emissions warranty. ‡ This maintenance is not required if previously replaced.
SCHEDULE “A”—TURBO 433 M SCHEDULE “A”—TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the Make-up air filter. Adjust the generator drive belt tension.
M 434 SCHEDULE “A”—TURBO A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Flush and replace engine coolant at 60 months, if not replaced at 100,000 miles.
SCHEDULE “A”—TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Replace the Make-up air filter. Adjust the generator drive belt tension.
M 436 SCHEDULE “A”—TURBO A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Replace the engine air cleaner filter. Replace the spark plugs. Adjust the generator drive belt tension. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Flush and replace the engine coolant if not done at 60 months. Replace the Make-up air filter.
SCHEDULE “A”—TURBO Miles (Kilometers) [Month] Change engine oil and engine oil filter. Rotate tires. Inspect the PCV Valve and replace if necessary. * Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emissions warranty. ‡ This maintenance is not required if previously replaced.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 440 ▫ Prepare For The Appointment . . . . . . . . . . . . 440 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 440 m Reporting Safety Defects . . . . . . . . . . . . . . . . . . 443 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 444 m Publication Order Forms . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
IF YOU NEED CONSUMER ASSISTANCE WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WARRANTY INFORMATION (U.S.
IF YOU NEED CONSUMER ASSISTANCE To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, DC 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov. PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below.
IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals. Filled with diagrams, charts and detailed illustrations, these practical manuals make it easy for students and technicians to find and fix problems on computercontrolled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-by-step troubleshooting and driveability procedures, proven diagnostic tests and a complete list of all tools and equipment. • Owner’s Manuals.
IF YOU NEED CONSUMER ASSISTANCE All Passenger Car Tires Must Conform to Federal Safety Requirements in Addition to These Grades. Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1 1/2) times as well on the government course as a tire graded 100.
IF YOU NEED CONSUMER ASSISTANCE grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. 447 WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.
INDEX 10
INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . 296 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 383 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 325 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 216 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 324 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 375 Air Conditioner Maintenance . . . . . . . . . . . . . . . 377 Air Conditioning Controls . . . . . . . . . . . . . .
INDEX Special Additives . . . . . . . . . . . . . . . . . . . . . . 392 Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288 Back-Up Lights . . . . . . . . . . . . . . . . . . . . . . . . . 408 Ball Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375 Keyless Transmitter Replacement (RKE) . . . . . 28,34 Belts, Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372 Belts, Engine . . . . .
INDEX Caution, Exhaust Gas . . . . . . . . . . . . . . . . . . . . . 113 CD (Compact Disc) Player . . . . . . . . . . . . . . . 242,250 CD (Compact Disc) Player Maintenance . . . . . . . . 268 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . 134,268 Center High Mounted Stop Light . . . . . . . . . . . . 409 Chains, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . . 344 Chart, Tire Sizing . . . . . . . . . . . . .
INDEX Adding Coolant (Antifreeze) . . . . . . . . . . . . . . 383 Coolant Level . . . . . . . . . . . . . . . . . . . . . . 382,385 Disposal of Used Coolant . . . . . . . . . . . . . . . . 384 Drain, Flush, and Refill . . . . . . . . . . . . . . . . . . 382 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . 385 Points to Remember . . . . . . . . . . . . . . . . . 384,385 Pressure Cap . . . . . . . . . . . . . . . . . . . . . . . . . 384 Selection of Coolant (Antifreeze) . . . . . . . . . . .
INDEX Electrical Power Outlets . . . . . . . . . . . . . . . . . . . 202 Electronic Speed Control (Cruise Control) . . . . . . 190 Electronic Vehicle Information Center (EVIC) . . . . 231 Emergency Deck Lid Release Latch (Convertible) . . 42 Emergency, In Case of Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 350 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Flat Tire Stowage . . . . . . . . . . . . . . . . . . . . . . . . 349 Flooded Engine Starting . . . . . . . . . . . . . . . . . . . 282 Fluid, Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . 412 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . . 410 Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Fluid Level Checks Automatic Transaxle . . . . . . . . . . . . . . . . . . . . 391 Fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Gasoline (Fuel) . . . . . . . . . . . . . . . . . . . . . . . 321,410 Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . 323 Gauges Coolant Temperature . . . . . . . . . . . . . . . . . . . . 224 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Gearshift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . 131 Instrument Cluster . . . . . . . . . . . . . . . . . . . . 221,224 Instrument Panel and Controls . . . . . . . . . . . . . . 220 Instrument Panel Cover . . . . . . . . . . . . . . . . . . . 398 Instrument Panel Lens Cleaning . . . . . . . . . . . . . 398 Integrated Power Module (Fuses) . . . . . . . . . . . . 400 Interior Appearance Care . . . . . . . . . . . . . . . . . . 396 Intermittent Wipers (Delay Wipers) . . . . . . . . . . .
INDEX Dimmer Switch, Headlight . . . . . . . . . . . . . . . 181 Engine Temperature Warning . . . . . . . . . . . . . . 228 Fog . . . . . . . . . . . . . . . . . . . . . . . . . . 183,229,407 Front Replacement . . . . . . . . . . . . . . . . . . . . . 406 Headlight Switch . . . . . . . . . . . . . . . . . . . . . . 182 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 High Beam Indicator . . . . . . . . . . . . . . . . . . . . 230 Instrument Cluster . . . . . . . . . . . . . . . . .
INDEX Schedule “A”-Turbo . . . . . . . . . . . . . . . . . . . . 433 Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . . 417 Schedule “B”-All Engines . . . . . . . . . . . . . . . . 417 Maintenance Schedules . . . . . . . . . . . . . . . . . . . . 414 Malfunction Indicator Light (Check Engine) . . 226,365 Manual Override, Convertible Top . . . . . . . . . 130,356 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . 444 Manual Transaxle . . . . . . . . . . . . . . . . . .
INDEX Materials Added to . . . . . . . . . . . . . . . . . . . . . 371 Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370 Recommendation . . . . . . . . . . . . . . . . . . . 370,410 Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371 Viscosity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370 Oil Pressure Light . . . . . . . . . . . . . . . . . . . . . . . 229 Onboard Diagnostic System . . . . . . . . . . . . . . 364,365 Opener, Garage Door (HomeLinkt) .
INDEX Pretensioners Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 52,86 Programmable Electronic Features . . . . . . 195,199,234 Programming Transmitters (Remote Keyless Entry) . . . . . . . . . . . . . 26,33,195,199 Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . . 314 Radio Broadcast Signals . . . . . . . . . . . . . . . . . . . 241 Radio Operation . . . . . . . . . . . . . . . . . . . 242,250,268 Radio, Satellite . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Safety Information, Tire . . . . . . . . . . . . . . . . . . . 302 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Satellite Radio . . . . . . . . . . . . . . . . . . . . . . . . . . 264 Satellite Radio Antenna . . . . . . . . . . . . . . . . . . . 267 Schedule, Maintenance . . . . . . . . . . . . . . . . . . . . 414 Seat Belt Maintenance . . . . . . . . . . . . . . . . . . . . 398 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . .
INDEX Sentry Key (Immobilizer) . . . . . . . . . . . . . . . . . 15,36 Sentry Key Programming . . . . . . . . . . . . . . . . . . . 17 Service and Maintenance . . . . . . . . . . . . . . . . . . 414 Service Assistance . . . . . . . . . . . . . . . . . . . . . . . 440 Service Contract . . . . . . . . . . . . . . . . . . . . . . . . . 442 Service Manuals . . . . . . . . . . . . . . . . . . . . . . . . 444 Setting the Clock . . . . . . . . . . . . . . . . . . 240,244,252 Settings, Personal . . . . . . . . . .
INDEX Tether Anchor, Child Restraint . . . . . . . . . . . . 75,108 Theft Alarm (Security Alarm) . . . . . . . . . . . . . . . . 35 Theft System (Security Alarm) . . . . . . . . . . . . . . . 35 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . . 189 Tire and Loading Information Placard . . . . . . . . . 306 Tire Identification Number (TIN) . . . . . . . . . . . . . 305 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . 302 Tire Safety Information . . . . . . . . . . . . . .
INDEX Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332 Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352 Traction Control . . . . . . . . . . . . . . . . . . . . . . . . . 300 Traction Control Switch . . . . . . . . . . . . . . . . . . . 300 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . 328 Cooling System Tips . . . . . . . . . . . . . . . . . . . . 340 Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Uniform Tire Quality Grades . . Universal Transmitter . . . . . . . Unleaded Gasoline . . . . . . . . . Untwisting Procedure, Seat Belt ............. ............. ............. ............ . 445 . 193 . 321 52,86 Vacuum/Vapor Harnesses . . . . . . . . . . . . . . . . . 386 Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . 133 Variance, Compass . . . . . . . . . . . . . . . . . . . . . . . 238 Vehicle Identification Number (VIN) . . . . . . . . . . . . 6 Vehicle Loading . .
INTRODUCTION INTRODUCTION HOW TO USE THIS MANUAL WARNINGS AND CAUTIONS VEHICLE IDENTIFICATION NUMBER VEHICLE MODIFICATIONS/ALTERATIONS THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key Removal Locking Doors With The KeyKey-In-Ignition ReminderSENTRY KEY - IF EQUIPPED Replacement KeysSentry Key ProgrammingGeneral InformationSTEERING WHEEL LOCK - IF EQUIPPED If You Wish To Manually Lock The Steering WheelTo Release The Steering Wheel LockAutomatic Transaxle Ignition Interlock Sys
