SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications / Alterations . . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER Vehicle Identification Number (VIN) is found on the driver’s front corner of the instrument panel, visible through the windshield.
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS 1 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . .13 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .13 ▫ Locking Doors With The Key . . . . . . . . . . . . . .14 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .15 䡵 Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 ▫ Replacement Keys . . . . . . . . . . . . . . . . . . . . . .16 ▫ Sentry Key Programming . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Unlock The Doors And Liftgate . . . . . . . . . .24 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .32 ▫ To Lock The Doors And Liftgate (If Equipped With Power Options) . . . . . . . . . .25 ▫ To Turn Off “Flash Lights With Lock” . . . . . . . .32 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .25 ▫ To Turn Off “Flash Lights With Lock” . . . . . . . .26 ▫ Programming Additional Transmitters . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 䡵 Emergency Deck Lid Release Latch (Convertible) . . . . . . . . . . . . . . . . . . . . . . . . . . .41 ▫ Driver And Front Passenger Supplemental Restraint System (SRS) - Airbag . . . . . . . . . . . .54 䡵 Power Windows . . . . . . . . . . . . . . . . . . . . . . . .42 ▫ Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .70 ▫ Auto Down Feature . . . . . . . . . . . . . . . . . . . .43 䡵 Occupant Restraints (Convertible) . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . 112 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . 113 ▫ Periodic Safety Checks You Should Make Outside The Vehicle . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place. 13 Ignition Key Removal Automatic Transaxle Place the shift lever in PARK and make sure that the shift knob push button has returned to the out position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If you try to remove the key before you place the lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key-In-Ignition Reminder Opening the driver’s door when the key is in the ignition, sounds a signal to remind you to remove the key. NOTE: With the driver’s door open, and the key in the ignition, both the power door locks and Remote Keyless Entry (RKE) will not function. SENTRY KEY The Sentry Key Immobilizer System prevents unauthorized operation of the vehicle by disabling the engine.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. • Exxon/Mobil Speed Pass,™ additional Sentry Keys, or any other transponder equipped components on the same keychain will not cause a key-related (transponder) fault unless the additional part is physically held against the ignition key being used when starting the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sentry Key Programming You can program new keys to the system if you have two valid sentry keys by performing the following procedure: 1. Cut the additional Sentry Key Transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the ignition switch and turn the ignition switch ON for at least 3 seconds but no longer than 15 seconds. Turn the ignition switch OFF and remove the first key. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE STEERING WHEEL LOCK — IF EQUIPPED Your vehicle may be equipped with a passive steering wheel lock. This lock prevents steering the vehicle without the ignition key. If the steering wheel is moved no more than 1/2 turn in either direction and the key is not in the ignition switch, the steering wheel will lock. If You Wish To Manually Lock The Steering Wheel: With the engine running, turn the steering wheel upside down, turn off the engine and remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 WARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death. CAUTION! Door Lock Plunger WARNING! For personal security, and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks A door lock switch is on each front door panel. Press this switch to lock or unlock the doors. 1. The Auto Lock feature is enabled. 2. The transmission is in gear. 3. All doors are closed. 4. The throttle is pressed. 5. The vehicle speed is above 15 mph (24 km/h). 6. The doors were not previously locked using the power door lock switch or remote keyless entry transmitter. The Automatic Door Lock feature can be enabled or disabled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 1. Close all doors and place the key in the ignition. 6. The vehicle speed is 0 mph (0 km/h). 2. Cycle the ignition switch between LOCK and ON and back to LOCK 4 times ending up in the LOCK position. The Auto Unlock feature can be enabled or disabled. Refer to “Personal Settings” (Customer Programmable Features) in the Electronic Vehicle Information Center (EVIC) — if equipped section of this manual. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE “Child-Protection” Door Lock System (Rear Doors) — If Equipped To provide a safer environment for children riding in the rear seat, the rear doors have the “child-protection” door lock system. To use the system, open each rear door and move the control UP to engage. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! 23 REMOTE KEYLESS ENTRY (SEDAN) Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. 2 NOTE: For emergency exit with the system engaged, move the lock plunger up (unlocked position), roll down window and open the door with the outside door handle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The line of transmission must not be blocked with metal objects. To unlock the doors and liftgate: Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors and liftgate. When the UNLOCK button is pressed, the illuminated entry will initiate, and the parking lights will flash on twice.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pressing the LOCK button on the keyfob while you are inside the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. 5. If the desired programming was not achieved or to reactivate this feature, repeat the above steps.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The panic alarm will stay on for 3 minutes unless you turn it off by pressing the PANIC button a second time or if the vehicle speed is 5 mph (8 km/h) or greater. NOTE: When you turn off the panic alarm by pressing the PANIC button a second time, you may have to be closer to the vehicle due to the radio frequency noises of the system. To Turn Off “Flash Lights With Lock” NOTE: The Flash Lights With Lock feature can be turned on or off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: When entering program mode using that fob, all other programmed fobs will be erased and you will have to reprogram them for your vehicle. Use the Following procedure to program additional key fobs if the vehicle is not equipped with Sentry Key: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (Fastening the seatbelt will cancel any chiming that may confuse you during this programming procedure). 3. Place the key into the ignition. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 14. Your vehicle will remain in program mode up to 60 seconds from when the original chime was heard. After 60 seconds, all programmed fobs function normally. NOTE: If you do not have a programmed transmitter, contact your dealer for details. General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 NOTE: If the key fob is equipped with a screw, reinstall and tighten the screw until snug. REMOTE KEYLESS ENTRY (CONVERTIBLE) Separating Transmitter Halves 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. Four Button Transmitter 3. To assemble the transmitter case, snap the two halves together.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE transmitter at the vehicle to activate the system. Each vehicle comes with two transmitters. To Unlock the Doors Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors and liftgate. When the UNLOCK button is pressed, the illuminated entry will initiate, and the parking lights will flash on twice.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pressing the LOCK button on the keyfob while you are inside the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. 5. If the desired programming was not achieved or to reactivate this feature, repeat the above steps. To lock the doors: Press and release the LOCK button on the transmitter to lock all doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using The Panic Alarm: To turn the panic alarm feature ON or OFF, press and hold the PANIC button on the transmitter for at least one second and release. When the panic alarm is on, the headlights and park lights will flash, the horn will pulse on and off and the interior lights will turn on. The panic alarm will stay on for 3 minutes unless you turn it off by pressing the PANIC button a second time or if the vehicle speed is 5 mph (8 km/h) or greater.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. 1. Gather every transmitter that is to be used with the vehicle including any transmitters that are currently programmed. The “Flash Lights On Lock/Unlock” feature can be reactivated by repeating this procedure. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information This transmitter complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received, including interference that may cause undesired operation. Transmitter Battery Service The recommended replacement battery is the Panasonic CR2032 or equivalent. 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch the battery, clean it with rubbing alcohol. 3. Reassemble the transmitter case. Snap the halves together and test transmitter operation. 35 system, which triggered the alarm is deactivated after the alarm has been on for 3 minutes the alarm will shut off immediately. To set the alarm: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To disarm the system: Unlock a front door/liftgate using the Keyless Entry Transmitter. Security System Manual Override The system will not arm if you lock the doors using the manual door lock plunger. Starting the vehicle with a valid Sentry key will disarm the system. A valid key is one that is programmed to that particular vehicle. A valid key will disarm the system, an invalid key will trigger the alarm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 LIFTGATE (SEDAN) NOTE: The key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate (if equipped). Rotate the key and pull the liftgate up. 2 To unlock the liftgate, insert the key into the lock and turn to the right. If equipped, the liftgate can also be unlocked using the remote keyless entry or by activating the power door lock switches located on the front doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • If you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode. Gas props support the liftgate in the open position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Gas props support the deck lid in the open position. However, because the gas pressure drops with temperature, it may be necessary to assist the props when opening the deck lid in cold weather. Power Deck Lid Release (Convertible) You can open the deck lid by pressing the Remote Keyless Entry Button or from inside the vehicle, using the switch located inside the glove box.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seat back can be unlatched by pulling down on the glow-in-the-dark lever attached to the left rear seat back latching mechanism. Emergency Seat Back Release Once unlatched the seat back can be pushed forward to gain access into the interior of the vehicle. NOTE: Make sure that the elastic loop is around the emergency release handle at all times.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE EMERGENCY DECK LID RELEASE LATCH (CONVERTIBLE) trunk can be simply opened by pulling on the glow-inthe-dark lever attached to the deck lid latching mechanism. See following picture. WARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the deck lid when your vehicle is unattended.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE POWER WINDOWS The power window switches are located on the instrument panel above the radio. The top left switch controls the left front window and the top right switch controls the right front window. The lower left switch controls the left rear passenger’s window and the lower right switch controls the right rear passenger’s window.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. Auto Down Feature The driver’s and passenger’s front window switches have an auto down feature. Press the window switch past the detent, release, and the window will go down automatically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is very dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your dealer and have it fixed. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Rear Center Lap/Shoulder Belt Retractor Lock-Out This feature is designed to lock the retractor whenever the rear seat back is not fully latched. This prevents someone from wearing the rear center lap/shoulder belt when the rear seat back is not fully latched. NOTE: • If the rear center lap/shoulder belt can not be pulled out, check that the rear seat back is fully latched.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. DaimlerChrysler does not recommend deactivating the Enhanced Warning System (BeltAlert). 1. Turn the ignition switch to the LOCK position and buckle the driver’s seat belt. 53 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have successfully completed the programming.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. Driver and Front Passenger Supplemental Restraint System (SRS) - Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE regulations that define Occupant Classification (Refer to ⬙Occupant Classification System⬙ in this section). If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seats, and their covers are also labeled SRS AIRBAG. 55 WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbags inflate in moderate to high speed impacts. Along with seat belts and pretensioners, front airbags work with the driver inflatable knee blocker to provide improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If a child from 1 to 12 years old must ride in the front passenger seat because the vehicle is crowded, move the seat as far back as possible, and use the proper child restraint. Refer to the section on Child Restraint. You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should wear their lap and shoulder belts properly. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The front airbag system consists of the following: • Driver and Front Passenger Seat Belt Pretensioners • Occupant Restraint Controller • Occupant Classification System (OCS) for the Front Passenger Seat • Side Remote Acceleration Sensors (If equipped) • Airbag Warning Light − Occupant Classification Module • Driver Airbag − Passenger Airbag Disable (PAD) Indicator Light • Passenger Airbag − Weight Sensors • Front Seat Mounted Side Airbags (If equip
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or RUN positions. These include all of the items listed above except the steering wheel and column, and knee bolsters. If the key is in the OFF position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate. During a moderate-to-severe rear impact the ORC may deploy the seat belt pretensioners alone.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint. • The OCS classifies an occupant using weight sensors mounted in the base of the front passenger seat. Any weight on the seat will be sensed by the system. Objects hanging on the seat or other passengers pushing down on the seat will also be sensed. The weight of an adult will cause the system to turn the airbag on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For all other occupants, the PAD indicator light will be illuminated indicating that the front passenger airbag is turned off and will not inflate. NOTE: Even though this vehicle is equipped with an occupant classification system, children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint (see section on child restraints). WARNING! Never place a rear facing infant seat in front of an airbag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE or instrument panel), the weight sensors in the seat may not properly classify the occupant. Objects lodged under the seat or between the seat and the center console can prevent the occupant’s weight from being measured properly and may result in the occupant being improperly classified. Ensure that the front passenger seat back does not touch anything placed on the second row of seats because this can also affect occupant classification.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE may be possible based on collision severity and occupant size. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the bags inflate to their full size. The bags fully inflate in about 50 - 70 milliseconds. This is about half of the time it takes to blink your eyes. The bags then quickly deflate while helping to restrain the driver and front passenger.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC Module monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or ON positions. These include all of the items previously mentioned. In moderate to severe side collisions, the side airbag inflator on the crash side of the vehicle is triggered, releasing a quantity of nontoxic gas. The inflating side airbag exits through the seat seam into the space between the occupant and the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The front passenger seat assembly contains critical components that affect the front passenger airbag deployment. Correctly functioning front passenger seat components are critical for the Occupant Classification System (OCS) to properly classify the front passenger and calculate the proper airbag deployment. Do not make any modifications to the front passenger seat components, assembly, or to the seat cover.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Unapproved modifications or service procedures to the front passenger seat assembly, its related components, or seat cover may inadvertently change the airbag deployment in case of a frontal crash. This could result in death or serious injury to the front seat passenger if the vehicle is involved in an accident. A modified vehicle may not comply with required Federal Motor Vehicle Safety Standards (FMVSS).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning. • It is not advisable to drive your vehicle after the airbags have deployed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately. • The AIRBAG light does not come on during the 6 to 8 seconds when the ignition switch is first turned on. • The light remains on after the 6 to 8 second interval.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the US government and various states. Data of a potentially sensitive nature, such as would identify a particular driver, vehicle, or crash, will be treated confidentially.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years and under should ride properly buckled up in a rear seat, if available.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and ⬙convertible⬙ child seats. Both types of child restraints are held in the vehicle by the lap/ shoulder belt or the LATCH child restraint anchorage system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s cushion while the child’s back is against the seat back; they should use a Belt Positioning Booster Seat. The child and booster seat are held in the vehicle by the lap/ shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it, before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the latch plate around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. • Buckle the child into the seat according to the child restraint manufacturer’s directions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 the outboard positions only. Regardless of the specific type of lower attachment, NEVER install LATCHcompatible child seats such that two seats share a common lower anchorage. If you are installing LATCHcompatible child restraints in adjacent rear seating positions, you can use the LATCH anchors or the vehicle’s seat belt for the outboard position, but you must use the vehicle’s seat belt at the center position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles. Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchorages will continue to have features for installation in vehicles using the lap or lap/shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 In general, you will first loosen the adjusters on the lower and tether straps so that you can more easily attach the hook or connector to the lower and tether anchorages. The tether strap should be routed under the center of the head restraint and attached to the tether anchor on the rear of the seat back. Then tighten all three straps as you push the child restraint rearward and downward into the seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a child restraint top tether strap. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS (CONVERTIBLE) Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger and if equipped, side airbags for both the driver and front passenger.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belts All the seats in your vehicle are equipped with Lap/ Shoulder Belts. If the belt webbing is twisted, and comes in contact with the wearers body, the twisted belt should be corrected using the Lap/Shoulder belt untwisting procedure found in this section. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Latch Plate To Buckle WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. 83 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! Seat Belt Webbing Guide NOTE: The manufacturer recommends that the seat belt is routed through the seat belt webbing guide when using the seat belt. The seat belt webbing guide should be used to improve seat belt accessibility.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upward over the folded webbing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Reminder System (BeltAlert) If the driver’s or front passenger’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert) will alert the driver or front passenger to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have successfully completed the programming. The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver’s or front passenger’s seat belt remains unbuckled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver and Front Passenger Supplemental Restraint System (SRS) - Airbag This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE regulations that define Occupant Classification (Refer to ⬙Occupant Classification System⬙ in this section). If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seats, and their covers are also labeled SRS AIRBAG. 89 WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbags inflate in moderate to high speed impacts. Along with seat belts and pretensioners, front airbags work with the driver inflatable knee blocker to provide improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If a child from 1 to 12 years old must ride in the front passenger seat because the vehicle is crowded, move the seat as far back as possible, and use the proper child restraint. Refer to the section on Child Restraint. You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should wear their lap and shoulder belts properly. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The front airbag system consists of the following: • Driver and Front Passenger Seat Belt Pretensioners • Occupant Restraint Controller • Occupant Classification System (OCS) for the Front Passenger Seat • Side Remote Acceleration Sensors (If Equipped) • Airbag Warning Light − Occupant Classification Module • Driver Airbag − Passenger Airbag Disable (PAD) Indicator Light • Passenger Airbag − Weight Sensors • Front Seat Mounted Side Airbags (If equip
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or RUN positions. These include all of the items listed above except the steering wheel and column, and knee bolsters. If the key is in the OFF position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate. During a moderate-to-severe rear impact the ORC may deploy the seat belt pretensioners alone.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The OCS classifies an occupant using weight sensors mounted in the base of the front passenger seat. Any weight on the seat will be sensed by the system. Objects hanging on the seat or other passengers pushing down on the seat will also be sensed. The weight of an adult will cause the system to turn the airbag on. In this case, the OCS has classified the occupant of the seat as an adult.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For all other occupants, the PAD indicator light will be illuminated indicating that the front passenger airbag is turned off and will not inflate. NOTE: Even though this vehicle is equipped with an occupant classification system, children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint (see section on child restraints). WARNING! Never place a rear facing infant seat in front of an airbag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE or instrument panel), the weight sensors in the seat may not properly classify the occupant. Objects lodged under the seat or between the seat and the center console can prevent the occupant’s weight from being measured properly and may result in the occupant being improperly classified. Ensure that the front passenger seat back does not touch anything placed on the second row of seats because this can also affect occupant classification.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE may be possible based on collision severity and occupant size. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the bags inflate to their full size. The bags fully inflate in about 50 - 70 milliseconds. This is about half of the time it takes to blink your eyes. The bags then quickly deflate while helping to restrain the driver and front passenger.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In moderate to severe side collisions, the side airbag inflator on the crash side of the vehicle is triggered, releasing a quantity of nontoxic gas. The inflating side airbag exits through the seat seam into the space between the occupant and the door. The side airbag moves at a very high speed and with such a high force, that it could injure you if you are not seated properly, or if items are positioned in the area where the side airbag inflates.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not modify the front seat center console or center position seat in any way. • Do not use prior or future model year seat covers not designated for the specific model being repaired. Always use the correct seat cover specified for the vehicle. • Do not replace the seat cover with an aftermarket seat cover. • Do not add a secondary seat cover other than those approved by DaimlerChrysler/Mopar.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • • • • • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE data gathered during a complete accident investigation, the electronic data may be used by DaimlerChrysler and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle performance.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Data Parameters that May Be Recorded: • Diagnostic trouble code(s) and warning lamp status for electronically-controlled safety systems, including the airbag system • Airbag disable lamp status (if equipped) • ⬙Time⬙ of airbag deployment (in terms of ignition cycles and vehicle mileage) • Airbag deployment level (if applicable) • Seatbelt status • Brake status (service and parking brakes) • Accelerator status (including vehicle speed) • Engine control status (inc
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children who weigh more than 9 kg (20 lbs) but are less than one year old. • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward facing child restraint should only be used in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE into the retractor, as the belt retracts, you will hear a clicking sound. This indicates that the seat belt is now in the automatic locking mode. Pull on the excess webbing to tighten the lap portion about the child restraint. Follow the instructions of the child restraint manufacture. NOTE: To reset this feature you must let all of the belt webbing return into the retractor.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seat cushion. They are round bars, part of the seat and body structure, and are readily visible. In addition, there are two tether strap anchorages located behind the rear seat head form, in the convertible top storage area. restraints having tether straps and hooks for connection to the top tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE installing the child restraint, buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach. If the buckled seat belt interferes with the child restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To gain access to the achorages, locate the child tether anchorage decals on the carpet behind the rear seat head forms and use a small screwdriver to pry the carpet flap open. The carpet flap is attached in two different places. Not all child restraint systems will be installed as we have described here. Again, carefully follow the instructions that come with the child restraint system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE over the front of the seat when their back is against the seat back, should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE shown in Section 7 of this manual. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED. Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil or other fluid leaks. Also, if gasoline fumes are detected or fuel, power steering fluid or brake fluid leaks are suspected, the cause should be located and corrected immediately.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Convertible Top Operation . . . . . . . . . . . . . . . . 119 ▫ Outside Mirror—Driver’s Side . . . . . . . . . . . . 132 ▫ To Lower The Top . . . . . . . . . . . . . . . . . . . . . 119 ▫ Outside Mirror—Passenger’s Side . . . . . . . . . . 132 ▫ To Raise The Top . . . . . . . . . . . . . . . . . . . . . 122 ▫ Electric Remote-Control Mirrors — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ UConnect™ System Features . . . . . . . . . . . . . 145 ▫ Folding Rear Seat (Sedan) . . . . . . . . . . . . . . . 165 ▫ Advanced Phone Connectivity . . . . . . . . . . . . 149 ▫ Folding Rear Seat (Convertible) . . . . . . . . . . . 166 ▫ Things You Should Know About Your UConnect™ System . . . . . . . . . . . . . . . . . . . . 151 ▫ Tumbling Rear Seat (Sedan) . . . . . . . . . . . . . . 168 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Daytime Running Lights (DRL) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 180 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . 180 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . 180 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . 181 ▫ Highbeam/Lowbeam Select Switch . . . . . . . . . 182 ▫ Passing Light . . . . . . . . . . . . . . . . . . . . . . . . 182 䡵 Windshield Wipers And Washers . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 ▫ Reprogramming A Single Button . . . . . . . . . . 196 ▫ Center Console/Armrest Storage Bin . . . . . . . 203 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 ▫ Storage Pockets . . . . . . . . . . . . . . . . . . . . . . . 205 䡵 Power Sunroof — If Equipped . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONVERTIBLE TOP OPERATION WARNING! The convertible top does not provide the structural protection that a reinforced metal roof does, and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision. Therefore it is important that all occupants wear their seat belts at all times when riding in a convertible.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! To fully insure that no damage occurs, be sure that the vehicle is at a complete stop with the gear selector in the Park position (automatic transaxle) or in the Neutral position (manual transaxle) before lowering or raising the top. To avoid damage to either the top or the rear window, check the top storage area at the rear of the vehicle interior to be sure that it is clear of debris or other items.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 the Power Top Switch lightly in the first detent position will lower the windows slightly and the convertible top to the full down position. Pressing and holding the switch in the second detent position will lower all four windows completely and the top to the full down position. Releasing Convertible Top Latches 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Continue pressing the Power Top Switch until the convertible top is lowered completely. 5. Install the Convertible Top Boot Cover, if equipped. Refer to Convertible Top Boot Cover Installation–If Equipped, in this section. CAUTION! Damage to the convertible top boot cover could result if the latch handle is not completely closed when the top is lowered. The convertible top boot cover cannot be installed while the latch handle is open.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 1. Remove the convertible top boot cover, if equipped. Refer to Convertible Top Boot Cover Removal and Storage, in this section. 2. Turn the ignition to the ON position. 3 3. Press the Power Top Switch to raise the top. Before the top reaches the windshield, open the latch handle and turn the handle clockwise to open the latches. Press the switch again to continue raising the top until the two pins seat themselves in the windshield header.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Car top carriers, ski racks, etc., should not be attached to the convertible top mechanism as they will damage the top. Do not place objects on the convertible top, in the top well or on the sport bar. Damage to the convertible top may occur. Convertible Top Boot Cover Installation–If Equipped 1. With the top down and the convertible top latch handle in the stowed position, lay the unfolded boot cover across the convertible top.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 2. Install the rear edge of the boot, first tucking the rear edge of the boot under the rear and both sides of the rails.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull the right and left boot arms forward and engage both boot arm snaps. Make sure both snaps are fully engaged.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Engage the boot center section retainer using the tabs provided. 127 5. Tuck the rear flap of the boot in behind the Upper Moulding.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Convertible Top Boot Cover Removal and Storage 1. Unsnap the snaps and remove the top cover boot. 2. Lay the boot cover flat with the center section retainer facing the rear of the car.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 3. First fold the left side of the boot cover to the middle of the boot cover. 3 Folding Boot Cover Right Side Folding Boot Cover Left Side 4. Second fold the right side of the boot cover to the middle, fitting it inside the left side of the boot cover and store it in the trunk or a dry secure area. CAUTION! Do not lay heavy objects on top of the boot or lay the boot on top of sharp/pointy objects. Damage could occur to the boot.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONVERTIBLE TOP MANUAL OVERRIDE If your vehicle is experiencing electrical failure (low battery, etc.) and it is necessary to raise the convertible top, perform the following steps: 1. Locate the convertible top motor bypass screw, which is found in the trunk under the convertible top storage area. 2. Turn the screw counterclockwise until the screw stops. This will relieve the hydraulic pressure and allow the convertible top to be raised manually.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Using the latch handle raise the top until the two pins seat themselves in the windshield header. 4. Rotate the latch handle clockwise to open the latches. 5. Pull down and rotate the handle counterclockwise to engage the latches. 131 6. Raise the handle into the stowed position. 7. Close the convertible top motor bypass screw by turning the screw clockwise until it stops. Tighten the screw securely.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield). Outside Mirror—Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Electric Remote-Control Mirrors — If Equipped The power mirror switch is located to the left of the steering column on the instrument panel. To adjust the view in the outside mirrors, turn the rotary knob to the left (L), center (O) or Right (R) position. After selecting the mirror, move the knob in the same direction you want the mirror to move. Use the center (O) position to guard against accidentally moving a mirror position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE An illuminated vanity mirror is on the sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights turn on automatically. Closing the mirror cover turns off the lights. Illuminated Vanity Mirror Sun Visor Sliding Feature The sun visors may be pulled out to provide extended coverage of the side glass.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s microphone for private conversation. The UConnect™ phonebook enables you to store up to 32 names and four numbers per name. Each language has a separate 32-name phonebook accessible only in that language. This system is driven through your Bluetooth™ Hands-Free profile cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ system can be used with any HandsFree Profile certified Bluetooth™ cellular phone. See www.chrysler.com/uconnect for supported phones. If your cellular phone supports a different profile (e.g., Headset Profile), you may not be able to use any UConnect™ features. Refer to your cellular service provider or the phone manufacturer for details.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE example, you can use the combined form voice command ⬙Phonebook New Entry,⬙ or you can break the combined form command into two voice commands: ⬙Phonebook⬙ and ⬙New Entry.⬙ Please remember, the UConnect™ system works best when you talk in a normal conversational tone, as if speaking to some one sitting eight feet away from you. Voice Command Tree Refer to “Voice Tree” at the end of this section.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing⬙ and follow the audible prompts. • When prompted, after the voice on beep, say ⬙Pair a Phone⬙ and follow the audible prompts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call/Dial by Saying a Number • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Dial.⬙ • System will prompt you to say the number you want call. • For example, you can say ⬙234-567-8901.⬙ • The UConnect™ system will confirm the phone number and then dial. The number will appear in the display of certain radios. Call/Dial by Saying a Name • Press the “Phone” button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook New Entry.⬙ • When prompted, say the name of the new entry. Use of long names helps the voice recognition and is recommended. For example, say ⬙Robert Smith⬙ or ⬙Robert⬙ instead of ⬙Bob.⬙ • When prompted, enter the number designation (e.g., ⬙Home,⬙ ⬙Work,⬙ ⬙Mobile,⬙ or ⬙Pager⬙). This will allow you to store multiple numbers for each phonebook entry, if desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 • When prompted, recite the new phone number for the phonebook entry that you are editing. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Delete.⬙ After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE After confirmation, the phonebook entries will be deleted. Note that only the phonebook in the current language is deleted. Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Erase All.⬙ • The UConnect™ system will ask you to verify that you wish to delete all the entries from the phonebook. • After confirmation, the phonebook entries will be deleted.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect™ system will interrupt the vehicle audio system, if on, and will ask if you would like to answer the call. To reject the call, press and hold the ’Phone’ button until you hear a single beep indicating that the incoming call was rejected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time. Conference Call When two calls are in progress (one active and one on hold), press and hold the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After ignition key is switched off, a call can continue on the UConnect™ system either until the call ends or until the vehicle battery condition dictates cessation of the call on the UConnect™ system and transfer of the call to the mobile phone. • After ignition key is switched to off, a call can continue on the UConnect™ system for certain duration, after which the call is automatically transferred from the UConnect™ system to the mobile phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the phone is not reachable and the UConnect™ system is operational, you may reach the emergency number as follows: • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Emergency⬙ and the UConnect™ system will instruct the paired cellular phone to call the emergency number. This feature is only supported in the USA.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Paging To learn how to page, refer to ⬙Working with Automated Systems.⬙ Paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the UConnect™ system. Voice Mail Calling To learn how to access your voice mail, refer to ⬙Working with Automated Systems.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g., the UConnect™ system will not repeat a phone number before you dial it). • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Confirmations.⬙ The UConnect™ system will play the current confirmation prompt status and you will be given the choice to change it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Mute/Un-mute (Mute off) When you mute the UConnect™ system, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the UConnect™ system: Information Service When using AT&T Wireless Service, dialing to phone number ⬙#121,⬙ you can access voice activated automated system to receive news, weather, stocks, traffic, etc. related information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you would like to connect or disconnect the Bluetooth™ connection between a UConnect™ paired cellular phone and the UConnect™ system, then follow the instruction described in your cellular phone user’s manual. Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system. The phone must have been previously paired to the UConnect™ system that you want to use it with.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete UConnect™ Paired Cellular Phones • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing.⬙ • At the next prompt, say ⬙Delete⬙ and follow the prompts. • You can also press the ⬘Voice Recognition’ button anytime while the list is being played and then choose the phone you wish to delete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Recognition (VR) • Always wait for the beep before speaking. • Speak normally, without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you. • Make sure that no one other than you is speaking during a voice recognition period. • Performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, and • dry weather condition. • Operation from driver seat. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 North American English Primary Alternate(s) Phone pairing Pairing Phonebook Phone book Return to main menu Return. Main menu Select phone select Set up Phone settings phone set up 3 SEATS Front Seat Adjustment The adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position. Manual Adjustment Bar Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 3 Power Seat Switch This seat also has a manual recline lever located just to the rear of the power seat switch. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Lumbar—If Equipped The Lumbar adjustment is located on the inboard side of the driver’s seat. To increase support, rotate the handle down. Folding Front Passenger Seat — If Equipped The passenger front seat may be folded fully forward to provide additional cargo space. To fold the seat forward pull up on the recliner lever located on the outboard side of the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Driver’s Seat Back Tilt—If Equipped How to operate the driver’s seat: 1. Push the lever down until seat back releases. 2. Push the seat back forward. 3 3. To return seat to a sitting position, push seat back rearward. NOTE: The driver’s front seat has a full recliner memory, which will allow the seat back to return to its original position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Push seat back forward until it slides toward the dashboard. 4. Push seat rearward until the track locks. NOTE: The passenger front seat has a full recliner memory, which will allow the seat back to returned to its original position. NOTE: The passenger front seat has a track memory, which returns the seat to just past the half way point of the track regardless of original position. Passenger Seat Back Tilt Lever 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Heated Seats — If Equipped WARNING! Adjustable Head Restraints Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE This feature heats the front driver’s and passenger’s seats. The control for the heater is located on the instrument panel, below the radio. After turning on the ignition, you may choose OFF, HIGH, or LOW heat settings. An indicator on the switch shows which setting has been chosen. Heated Seat Switches Pressing the switch once will select high-level heating. Pressing the switch a second time will select low-level heating.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat (Sedan) To provide additional storage area, each rear seatback can be folded forward. Push and hold the buttons shown in the picture to fold down either or both seatbacks. Folding Rear Seat Button 165 WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If the seatback is properly latched and the rear center lap/shoulder belt still does not operate properly check and see if the Automatic Locking retractor (ALR) system is activated. WARNING! The rear center lap/shoulder belt is equipped with a lock-out feature to ensure that the seatback is in the fully upright and locked position when occupied.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure that everyone in your vehicle is in a seat and using a seat belt properly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tumbling Rear Seat (Sedan) To provide additional storage in the cargo area, each rear seat can be tumbled forward. • Push and hold the button on the seatback and fold down the rear seatback. CAUTION! It is important that the front seats be pulled forward to the midpoint of the seat track to avoid contact between the rear seat and the front seatback.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 • Pull the release handle located on the outboard side of the seat. Lift up the seat and tumble the seat forward. 3 Tumbling Seat Strap Tumbling Seat Release Strap • Attach the elastic strap, located at the base of the seat cushion, onto the hook bar on the center trim panel to hold the seat in place. To return the rear seat to it’s upright latched position, rotate the seat cushion rearward to latch the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tumbling Rear Seat (Convertible) To provide additional storage area, each rear seat can be tumbled forward. CAUTION! To tumble the seat forward use the following procedure: 1. The seat back release knobs are located in the trunk area. Pull the left side seatback release knob to fold down the left side seatback. Pull the right side seatback release knob to fold down the right side seatback.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. From inside the vehicle, fold the rear seat back down flat. 171 3. Pull the release handle located at the bottom of the folded seat back and tumble the seat forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Attach the cinching tether strap, located at the side of the seat cushion, onto the hook bar on the center trim panel and tighten by pulling the cinching strap until the seat is secure. Cinching Tether Strap To return the tumbling rear seat to the latched (normal) position use the following procedure: 1. Loosen the strap by pushing rearward on the cinching tether strap buckle. Releasing Cinching Tether Strap 2. Disconnect the cinching tether strap.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 NOTE: The strap should be reinstalled in the side pocket on the seat cushion before returning the seat to the latched (normal) position. NOTE: Prior to lifting either seatback to the upright position, be sure that the seat belt is brought forward to avoid trapping it behind the seatback. NOTE: Prior to rotating the seat cushions rearward, be sure that the rear seat belt buckles are secured with the straps, so that the buckles are accessible. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Seat Removal (Sedan) The rear seats can be removed to provide more cargo space. • Pull the release lever located on the outboard side of the seat. Lift up the seat and tumble the seat forward. • Push and hold the button on the seatback and fold down the rear seatback. Tumbling Seat Release Strap • Lift up the release levers to disengage the seat from the floor attachments.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 To reinstall the rear seat, insert the seat into the floor attachments. Lower the release levers of the seat to latch the front floor attachments and rotate the seat rearward to latch the seat. Lift the seat back to its upright latched position. WARNING! In an accident, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure the seats are fully latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Then move the safety catch located under the front edge of the hood, near the center and slightly to the right, and raise the hood. Use the hood prop rod clipped to the driver’s side of the engine compartment to secure the hood in the open position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 WARNING! If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. 3 LIGHTS Map/Reading Lights (Sedan) These lights are mounted between the sun visors above the rear view mirror. Each light is turned ON by pressing the button. Press the button a second time to turn the light OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Map/Reading Lights (Convertible) When the ignition switch is in the ON position, these lights, located under the rearview mirror can be turned on by switches located at the base of the rearview mirror. NOTE: The lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. They will not turn off automatically.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights, Parking Lights, Instrument Panel Lights Turn the end of the Multi-Function Control Lever to the first detent for parking light operation. Turn to the second detent for headlight operation. To change the brightness of the instrument panel lights, rotate the center portion of the Multi-Function Control Lever up or down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights (DRL) — If Equipped The high beam lights will come on as Daytime Running Lights (DRL) at DRL intensity (lower), whenever the ignition is on, the engine is running, the headlight switch is off, the parking brake is off, the turn signal is off, and the gear shift is in any position except park.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The fog lights will only operate with the headlights on low beam. Selecting high beam headlights will turn off the fog lights. Turn Signals 181 Move the Multi-Function Control Lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down without moving beyond the detent.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Highbeam/Lowbeam Select Switch Passing Light You can signal another vehicle with your headlights by lightly pulling the Multi-Function Control Lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released. NOTE: If the Multi-Function Control Lever is held in the flash to pass position for more than 15 seconds, the high beams will shut off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 If the lever is pulled while in the OFF position, the wipers will operate for two wipe cycles, then turn OFF. Mist Feature Push down on the wiper control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. CAUTION! Wiper/Washer Switch Windshield Washers To use the washer, pull the control lever toward you and hold while spray is desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wiper Operation Rotate the control to the second detent for Low speed wiper operation, or to the third detent for High speed operation Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, push down on the lever below the multifunction control lever and move the steering wheel up or down, as desired. Pull the lever back up to lock the column firmly in place. 185 WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To turn the system OFF, press the TCS switch until the traction control indicator in the instrument cluster lights up. To turn the system back ON, press the switch a second time until the traction control indicator turns OFF. NOTE: The traction control indicator will illuminate momentarily as a bulb check, each time the ignition switch is turned ON. This will occur even if you used the TCS switch to turn the system OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 35 mph (56 km/h). The speed control lever is located on the right side of the steering wheel. 187 To Activate: Push the ON/OFF button. The CRUISE indicator in the instrument cluster will illuminate. To turn the system OFF, push the ON/OFF button a second time. The CRUISE indicator will turn off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Set At A Desired Speed: When the vehicle has reached the desired speed, press down on the lever and release. Release the accelerator and the vehicle will operate at the selected speed. To Resume Speed: To resume a previously set speed, push the “RESUME ACCEL” lever up and release. Resume can be used at any speed above 20 mph (32 km/h). NOTE: The vehicle should be traveling at a steady speed and on level ground before pressing the SET lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tapping the “SET DECEL” button once will result in a 1 mph (2 km/h) speed decrease. Each time the button is tapped, speed decreases. Manual Transaxle: Depressing the clutch pedal will disengage the speed control. A slight increase in engine RPM before the speed control disengages is normal. Vehicles equipped with manual transaxles may need to be shifted into a lower gear to climb hills without speed loss.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vehicles equipped with four speed automatic transaxles may experience a downshift to 3rd gear while climbing uphill or descending downhill. This downshift to 3rd gear is necessary to maintain vehicle set speed. push of a button. The Universal Transceiver operates off your vehicle’s battery and charging system; no batteries are needed. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 WARNING! HomeLink Buttons (Convertible) For additional information on HomeLink威, call 1–800– 355–3515, or on the internet at www.homelink.com. A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming The Universal Transceiver For best results, install a new battery in the hand held transmitter before programming. If your garage door opener (located in the garage) is equipped with an antenna, make sure that the antenna is hanging straight down. 1. Turn off the engine. WARNING! Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run the vehicle’s exhaust while training the transceiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 3. Choose one of the three Universal Transceiver buttons to program. Place the hand held controller one to three inches from the Universal Transceiver while keeping its indicator light in view. 3 HomeLink Programming (Convertible) 4. Using both hands, press the hand held transmitter button and the desired Universal Transceiver button. Do not release the buttons until step 5 has been completed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. The indicator light in the Universal Transceiver will begin to flash, first slowly and then rapidly. The rapid flashing indicates successful programming. If after 90 seconds the indicator light does not flash rapidly or goes out, return to step 1 and repeat the procedure. To train the other buttons, repeat steps 3 and 4. Be sure to keep your hand held transmitters in case you need to retrain the Universal Transceiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The assistance of a second person may make the following programming procedure quicker and easier. 1. Locate the training button on the garage door motor head unit. The exact location and color of the button may vary by garage door opener manufacturer. If you have difficulty in locating the training button, check your garage door opener manual, or call 1-800-355-3515 or, on the Internet, at www.homelink.com. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Universal Transceiver light will flash slowly and then rapidly when the programming is successful. NOTE: When programming such a garage door opener or gate, unplug the device to prevent possible damage to the garage door or gate motor. Operation Press and hold the desired button on the Universal Transceiver until the garage door or other device begins to operate. The light in the display shows that the signal is being transmitted.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 3 HomeLink威 is a trademark owned by Johnson Controls, Inc. POWER SUNROOF — IF EQUIPPED The power sunroof switch is located in the reading lamp.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press and hold the button in the center of the sunroof switch to open the vent. The sunroof can be stopped at any position between closed and full vent. To close the sunroof from the vent position, press and hold the switch forward. Releasing the switch will stop the movement of the sunroof and the sunroof will remain in the partial vent position until the switch is pushed forward again.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. Do not allow small children to operate the sunroof. Never allow fingers or other body parts, or any object to project through the sunroof opening. Injury may result.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS The outlets include tethered caps, labeled with a key symbol or battery symbol, indicating power source. All outlets are protected by a single 20 Amp fuse. The standard outlet in the front of the center floor console is a conventional cigar lighter outlet. It will accept a cigar lighter unit, which is part of the optional Smokers Package.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 3 Center Console Power Outlet Rear Power Outlet This outlet is powered directly by the battery, regardless of the ignition switch position. All accessories connected to this outlet should be removed or turned off when the vehicle is not in use, to protect the battery against discharge.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e. coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged into the 12 volt power outlet, draw power from the vehicle’s battery, even when not in use; i.e. cellular phones, etc. Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power such as coolers, vacuum cleaners, lights, etc., will discharge the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The center console provides a sliding armrest with two unique storage compartments under the lid. Sliding Armrest Storage Bins Push the upper button on the front of the armrest to raise the upper cover. Inside is a slot for a power cord, an area to store a cell phone, and other miscellaneous items. Push the lower button on the front of the armrest, and raise the armrest for access to the lower storage bin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e. coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • To avoid tipping, lock the shelf securely in all positions. • Do not drive this vehicle with the liftgate open, or use the shelf as a seat. • Failure to follow these warnings could result in serious or fatal injury. Position 1 (Top) Insert the front outboard corners of the shelf panel into the top guides and slide forward. Press down on the back of the shelf panel to lock it into place.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Position 2 (Middle) Insert the front outboard corners of the shelf panel into the middle guides and slide forward. Press down on the back of the shelf panel to lock it into place. 207 WARNING! Do not load objects over 100 lbs (45 kg) in position 2 (middle). Failure to follow this warning could cause the shelf to collapse resulting in personal injury. Position 3 (Floor) Insert the front outboard corners of the shelf panel into the bottom guides and slide forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Position 4 (Vertical) Insert the front outboard corners of the shelf panel into the vertical guides behind the rear seatbacks near the floor and slide downward. Push the shelf panel forward to lock it into place. WARNING! When in the vertical position, the rear shelf panel should not be used as a barrier for large objects in the cargo area when the seatbacks folded down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 2. Twist the knob on the underside of the panel and lower the shelf leg. 3 Rear Shelf Panel Position 5 Rear Shelf Leg Release Knob 3. Install the shelf leg into the liftgate latch area as labeled on the rear scuff plate. WARNING! Do not load objects over 100 lbs (45 kg) in position 5 (table). Failure to follow this warning could cause the shelf to collapse resulting in personal injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Use both adjustable crossbars assemblies to support the load and distribute the load as evenly as possible.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 CAUTION! WARNING! To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately. Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . . . 216 ▫ Average Fuel Economy . . . . . . . . . . . . . . . . . 230 䡵 Instrument Cluster—Base . . . . . . . . . . . . . . . . . 217 ▫ Distance To Empty (DTE) . . . . . . . . . . . . . . . 230 䡵 Instrument Cluster—Premium . . . . . . . . . . . . . . 218 ▫ Elapsed Time . . . . . . . . . . . . . . . . . . . . . . . . 231 䡵 Instrument Cluster—Turbo . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Electrical Disturbances . . . . . . . . . . . . . . . . . . 237 ▫ AM Reception . . . . . . . . . . . . . . . . . . . . . . . 237 ▫ FM Reception . . . . . . . . . . . . . . . . . . . . . . . . 237 䡵 Sales Code REF — AM/FM/CD (Single Disc) Radio With Optional Satellite Radio And Hands Free Phone Capability . . . . . . . . . . . . . . . . . . . 238 ▫ Operating Instructions - Radio Mode . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) . . . . . . . . . . . . . . . . . . . . 260 ▫ Selecting Satellite Mode In REF, And RAQ, Radios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 ▫ Selecting a Channel . . . . . . . . . . . . . . . . . . . . 262 ▫ Storing And Selecting Pre-Set Channels . . . . . . 262 215 ▫ Reception Quality . . . . . . . . . . . . . . . . . . . . . 264 䡵 CD/DVD Disc Maintenance . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES
UNDERSTANDING YOUR INSTRUMENT PANEL 217 INSTRUMENT CLUSTER—BASE 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER—PREMIUM
UNDERSTANDING YOUR INSTRUMENT PANEL 219 INSTRUMENT CLUSTER—TURBO 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Fuel Door Reminder This is a reminder that the Fuel Filler Door is located on the front passenger’s (right) side of the vehicle. 3. Temperature Gauge The temperature gauge shows engine coolant temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL 5. Tachometer The white area of the scale shows the permissible engine revolutions-per-minute (rpm x 1000) for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 6. Transmission Range Indicator This display indicator shows the automatic transmission gear selection. 7. Odometer/Trip Odometer A vacuum fluorescent display indicates the total distance the vehicle has been driven.
UNDERSTANDING YOUR INSTRUMENT PANEL 9. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD that monitors emissions, engine, and automatic transmission control systems. The light will illuminate when the key is in the ON/RUN position before engine start. If the bulb does not come on when turning the key from OFF to ON/RUN, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc.
UNDERSTANDING YOUR INSTRUMENT PANEL 12. Brake System Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, there is a low brake fluid level or there is a problem with the anti-lock brake system. The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system.
UNDERSTANDING YOUR INSTRUMENT PANEL the ON position. The light should illuminate for approximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. 14. Engine Temperature Warning Light This light warns of an overheated engine condition. If the engine is critically hot, a warning chime will sound 10 times.
UNDERSTANDING YOUR INSTRUMENT PANEL 17. Low Fuel Light When the fuel level drops to 2 gallons, the fuel symbol will light and a single chime will sound. 18. Anti-Lock Warning Light (ABS) — If Equipped This light monitors the Anti-Lock Brake System (ABS) described elsewhere in this manual. This light will come on when the ignition key is turned to the ON position and may stay on for as long as four seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 21. Oil Pressure Light Shows low engine oil pressure. The light will come on and remain on when the ignition switch is turned from the OFF to the ON position, and the light will turn off after the engine is started. If the bulb does not come on during starting, have the system checked by an authorized dealer. If the light comes on and remains on while driving, stop the vehicle and shut off the engine. DO NOT OPERATE THE VEHICLE UNTIL THE CAUSE IS CORRECTED.
UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC)–If Equipped 227 • System Status • Vehicle information warning message displays • Personal Settings (customer programmable features) • Compass heading • Outside temperature display • Trip computer functions • UConnect™ hands-free communication system displays — If Equipped • Audio mode display EVIC Location The Electronic Vehicle Information Center (EVIC) features a driver-interactive display.
UNDERSTANDING YOUR INSTRUMENT PANEL When the appropriate conditions exist, the Electronic Vehicle Information Center (EVIC) displays the following messages.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 • Distance To Empty (DTE) EVIC Functions • Elapsed Time • Personal Settings To Reset The Display Pressing and holding the EVIC button once will clear the resettable function currently being displayed. Reset will only occur if a resettable function is currently being displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL Compass/Temperature/Audio Press and release the EVIC button to display one of eight compass headings to indicate the direction the vehicle is facing, the outside temperature and the current radio station. For additional information regarding the compass, refer to Personal Settings (Customer Programmable Features) in this section. Average Fuel Economy Shows the average fuel economy since the last reset.
UNDERSTANDING YOUR INSTRUMENT PANEL Elapsed Time Shows the total elapsed time of travel since the last reset when the ignition switch is in the ACC position. Elapsed time will increment when the ignition switch is in the ON or START position. Personal Settings (Customer Programmable Features) This allows the driver to set and recall features when the transmission is in PARK (automatic transmission) or the vehicle is stopped (manual transmissions).
UNDERSTANDING YOUR INSTRUMENT PANEL Auto Unlock On Exit When ON is selected all the vehicle’s doors will unlock when the driver’s door is opened if the vehicle is stopped (manual transmissions) or the vehicle is stopped and the transmission is in P (Park) or N (Neutral) position (automatic transmissions). Press and hold the EVIC button when in this display until “ON” or “OFF” appears to make your selection.
UNDERSTANDING YOUR INSTRUMENT PANEL when exiting the vehicle. Press and hold the EVIC button when in this display until 0, 30, 60, or 90 appears to make your selection. Headlamps On With Wipers (Available with Auto Headlights Only) When ON is selected and the headlight switch is in the AUTO position, the headlights will turn on approximately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on by this feature.
UNDERSTANDING YOUR INSTRUMENT PANEL Display English or Metric The EVIC, odometer, and navigation system units can be changed between English and Metric. Press and hold the EVIC button when in this display until “US” or “METRIC” appears to make your selection. Compass Variance Compass Variance is the difference between magnetic North and Geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings.
UNDERSTANDING YOUR INSTRUMENT PANEL To set the variance: with the ignition in the ON position, with a short button press (less than one seconds) press and release the EVIC button several times until you have displayed the Personal Settings (Customer Programmable Features) menu. Once in the Personal Settings (Customer Programmable Features) menu, press and release (less than one seconds) the EVIC button several times until “Compass Variance” is highlighted.
UNDERSTANDING YOUR INSTRUMENT PANEL calibration mode. The Cal indicator will come on continuously in the EVIC display to indicate that the compass is now in the calibration mode and that the vehicle can now be driven to calibrate. (A short EVIC button press from the ⬙Calibrate Compass (Yes)⬙ screen will exit the EVIC Customer Programmable features, and return it to its normal operating mode).
UNDERSTANDING YOUR INSTRUMENT PANEL RADIO GENERAL INFORMATION Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile operation and natural phenomena, which might lead you to believe your sound system is malfunctioning.
UNDERSTANDING YOUR INSTRUMENT PANEL will remain active for up to 10 minutes after the ignition switch has been turned off. Opening a vehicle front door will cancel this feature. SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL SATELLITE RADIO AND HANDS FREE PHONE CAPABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate. REF Radio Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it. When the audio system is turned on, the sound will be set at the same volume level as last played.
UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station in either, AM, FM, or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time.
UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control and BASS will display. Turn the TUNE control to the right or left to increase or decrease the Bass tones. Press the rotary TUNE control a second time and MID will display. Turn the TUNE control to the right or left to increase or decrease the Mid Range tones. Press the rotary TUNE control a third time and TREB will display.
UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM, 12 FM, and 12 Satellite (if equipped) stations to be stored into push-button memory. The stations stored in SET 2 memory can be selected by pressing the push-button twice.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 • If you insert a disc with the ignition ON and the radio OFF, the CD will automatically be pulled into the CD Player. SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. • This radio does not play discs with MP3 tracks. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal.
UNDERSTANDING YOUR INSTRUMENT PANEL RND/SET Button (Random Play Button) (CD Mode) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace.
UNDERSTANDING YOUR INSTRUMENT PANEL MUTE Button (Auxiliary Mode) Press the MUTE button to cancel the sound from the speakers. ⬙MUTE⬙ will display. Press the MUTE button a second time and the sound from the speakers will return. Rotating the volume control or turning OFF the ignition will also return the sound from the speakers. SCAN Button (Auxiliary Mode) No function. EJECT Button (Auxiliary Mode) No function. PSCAN Button (Auxiliary Mode) No function.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Radio — If Equipped Refer to the “Satellite Radio” section of the Owner’s Manual. SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, AND VEHICLE ENTERTAINMENT SYSTEMS (VES) CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it. When the audio system is turned on, the sound will be set at the same volume level as last played.
UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time. MSG or INFO Button (Radio Mode) Press the MSG or INFO button for an RBDS station (one with call letters displayed).
UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control and BASS will display. Turn the TUNE control to the right or left to increase or decrease the Bass tones. Press the rotary TUNE control a second time and MID will display. Turn the TUNE control to the right or left to increase or decrease the Mid Range tones. Press the rotary TUNE control a third time and TREBLE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the PTY button to select the following format types: Program Type No program type or undefined Adult Hits Alert Alert Classical Classic Rock College Country Emergency Test Foreign Language Information Jazz News 16 Digit-Character Display None Adult_Hits Alert Alert Classical Classic_Rock College Country Emergency Test Foreign_Language Information Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Roc
UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (CD MODE for CD Audio Play) CAUTION! NOTE: The ignition switch must be in the ON or ACC position to operate the radio. This CD player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism.
UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button (CD MODE for CD Audio Play) Press the right side of the SEEK button for the next selection on the CD. Press the left side of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. MUTE Button (CD MODE for CD Audio Play) Press the MUTE button to cancel the sound from the speakers. ⬙MUTE⬙ will be displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. Press and hold the LOAD/ EJT button for 5 seconds and all CDs will be ejected from the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not removed, the radio will continue to play the non-removed CD.
UNDERSTANDING YOUR INSTRUMENT PANEL RND/PTY Button (Random Play Button) (CD MODE for CD Audio Play) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track. Press and hold the FF button to fast forward through the tracks. Release the FF button to stop the fast forward feature.
UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙.⬙ and a 3-character extension) • Level 2: 31 (including a separator ⬙.⬙ and a 3-character extension) Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files).
UNDERSTANDING YOUR INSTRUMENT PANEL MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 Sampling Frequency (kHz) 48, 44.1, 32 24, 22.05, 16 Bit rate (kbps) 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 ID3 Tag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported.
UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (CD Mode for MP3 Audio Play) SEEK Button (CD Mode for MP3 Play) Pressing the right side of the SEEK button plays the next MP3 File. Pressing the left side of the SEEK button plays the beginning of the MP3 file. Pressing the button within the first ten seconds plays the previous file.
UNDERSTANDING YOUR INSTRUMENT PANEL MSG or INFO Button (CD Mode for MP3 Play) Press and MSG or INFO button while playing MP3 disc. The radio scrolls through the following TAG information: Song Title, Artist, File Name, and Folder Name (if available). Press the MSG or INFO button once more to return to ⬙elapsed time⬙ priority mode. Press and hold the MSG or INFO button while in the message display priority mode or elapsed time display priority mode will display the song title for each file.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. Operating Instructions - Video Entertainment System (VES威) (If Equipped) Refer to separate Video Entertainment System (VES威) Guide. SATELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius™ Satellite Radio.
UNDERSTANDING YOUR INSTRUMENT PANEL ESN/SID Access With REF Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and Time buttons simultaneously for 3 seconds. The first four digits of the twelve-digit ESN/SID number will be displayed. Press the SEEK UP button to display the next four digits. Continue to press the SEEK UP button until all twelve ESN/SID digits have been displayed. The SEEK DOWN will page down until the first four digits are displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL These radios will also display the current station name and program type. For more information such as song title and artist press the MSG or INFO button. A CD or tape may remain in the radio while in the Satellite radio mode. Selecting a Channel Press and release the SEEK or TUNE knob to search for the next channel. Press the top of the button to search up and the bottom of the button to search down.
UNDERSTANDING YOUR INSTRUMENT PANEL PTY Button ⴖSCANⴖ When the desired program type is obtained, press the ⬙SCAN⬙ button within five seconds. The radio will play 7 seconds of the selected channel before moving to the next channel of the selected program type. Press the ⬙SCAN⬙ button a second time to stop the search. NOTE: Pressing the ⬙SEEK⬙ or ⬙SCAN⬙ button while performing a music type scan will change the channel by one and stop the search.
UNDERSTANDING YOUR INSTRUMENT PANEL Reception Quality Satellite reception may be interrupted due to one of the following reasons. CD/DVD DISC MAINTENANCE To keep the CD/DVD discs in good condition, take the following precautions: • The vehicle is parked in an underground parking structure or under a physical obstacle. 1. Handle the disc by its edge; avoid touching the surface. • Dense tree coverage may interrupt reception in the form of short audio mutes. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 265 RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being ON in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL The controls are as follows: Fan Control Use this control to regulate the amount of air forced through the system in any mode you select. The fan speed increases as you move the control to the right from the OFF position. Mode Control (Air Direction) The mode control allows you to choose from several patterns of air distribution. You can select either a primary mode, as identified by the symbols, or a blend of two of these modes.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. Floor Air is directed through the floor outlets and side window demist outlets with a small amount through the defrost outlet. Mix Air is directed through the floor, defrost and side window demist outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control Air Conditioning Use this control to regulate the temperature of the air inside the passenger compartment. The blue area of the scale indicates cooler temperatures while the red area indicates warmer temperatures. Use this button to engage the Air Conditioning.
UNDERSTANDING YOUR INSTRUMENT PANEL Circulation Control Use this button to choose between outside air intake or recirculation of the air inside the vehicle. A lamp will illuminate when you are in recirculate mode. Only use the recirculate mode to temporarily block out any outside odors, smoke, or dust and to cool the interior rapidly upon initial start up in very hot or humid weather. 269 NOTE: Continuous use of the recirculate mode may make the inside air stuffy and window fogging may occur.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips
UNDERSTANDING YOUR INSTRUMENT PANEL 271 Window Fogging Vehicle side windows tend to fog on the inside in mild rainy or humid weather. To clear the windows, use the A/C, PANEL and blower controls. Direct the panel outlets toward the side windows. Do not use recirculate without A/C for long periods as fogging may occur.
UNDERSTANDING YOUR INSTRUMENT PANEL Side Window Demisters A side window demister outlet is at each end of the instrument panel. These nonadjustable outlets direct air toward the side windows when the system is in either the FLOOR, MIX, or DEFROST mode. The air is directed at the area of the windows through which you view the outside mirrors. REAR WINDOW FEATURES Electric Rear Window Defroster Rear Defroster Switch The push-button is located at the center of the instrument panel, below the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 273 CAUTION! To avoid damaging the electrical conductors, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the rear window. Labels can be peeled off after soaking with warm water. Rear Wiper/Washer Switch — If Equipped A switch on the right side of the steering column controls operation of the rear wiper/washer function. Rotating the center of the switch forward to the ON position will activate the wiper.
UNDERSTANDING YOUR INSTRUMENT PANEL Adding Washer Fluid The fluid reservoir for the windshield washers and the rear window washer (If Equipped) is shared. It is located in the rear of the engine compartment on the passenger side and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . . 278 䡵 Automatic Transaxle — If Equipped . . . . . . . . . 281 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . . 278 ▫ Brake/Transmission Interlock System . . . . . . . 282 ▫ Manual Transaxle . . . . . . . . . . . . . . . . . . . . . 279 ▫ Automatic Transaxle Ignition Interlock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282 ▫ Normal Starting . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING ▫ AutoStick General Information . . . . . . . . . . . . 287 ▫ Tire Loading And Tire Pressure . . . . . . . . . . . 303 䡵 Manual Transaxle Operation . . . . . . . . . . . . . . . 288 䡵 Tires — General Information . . . . . . . . . . . . . . . 307 ▫ 2.4 Liter Turbo— If Equipped . . . . . . . . . . . . . 289 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . 307 ▫ Recommended Shift Speeds . . . . . . . . . . . . . . 290 ▫ Tire Inflation Pressures . . . . . . .
STARTING AND OPERATING 277 䡵 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 317 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . . 325 䡵 Tire Rotation Recommendations . . . . . . . . . . . . 317 䡵 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . . . 326 䡵 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . . 318 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . 326 ▫ 2.4L Standard Engine And 2.4L Standard Turbo Engine . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle.
STARTING AND OPERATING Manual Transaxle Before starting the engine fully apply the parking brake, press the clutch pedal to the floor and place the gear selector in NEUTRAL. NOTE: The engine will not start unless the clutch pedal is pressed to the floor. Normal Starting Normal Starting of either a cold or a warm engine does not require pumping or depressing the accelerator pedal. Simply turn the ignition switch to the “START’” position and release when the engine starts.
STARTING AND OPERATING If Engine Fails to Start If the engine fails to start after you have followed the “NORMAL STARTING” procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there. Crank the engine for no more than 15 seconds. This should clear any excess fuel in case the engine is flooded. Leave the ignition key in the ON position, release the accelerator pedal and repeat the “NORMAL STARTING” procedure.
STARTING AND OPERATING 281 TURBOCHARGER ⴖCOOL DOWNⴖ CHART Driving Conditions Idle Time (in minutes) Before Shut Down Normal Driving Not required. Aggressive Driving or Heavily Loaded 3 Trailer Tow 5 AUTOMATIC TRANSAXLE — IF EQUIPPED CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
STARTING AND OPERATING WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
STARTING AND OPERATING Four Speed Automatic Transaxle The electronically controlled transaxle provides a precise shift schedule. The transaxle electronics are self calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few shift cycles. Reset Mode The transaxle is monitored electronically for abnormal conditions.
STARTING AND OPERATING brake when leaving the vehicle in this range. Always apply the parking brake first, and then place the selector in P (Park) position. The following indicators should be used to ensure that you have engaged the transmission shift lever into the P (Park) position: WARNING! • When shifting into P (Park), depress the button on the shift lever and firmly move the lever all the way forward until it stops. Unintended movement of a vehicle could injure those in and near the vehicle.
STARTING AND OPERATING CAUTION! Before moving the shift lever out of P (Park), you must turn the ignition from LOCK to ON so the steering wheel and shift lever are released. Otherwise, damage to the steering column or shifter could result. “R” Reverse Shift into this range only after the vehicle has come to a complete stop. “N” Neutral Engine may be started in this range. “D” Overdrive This range should be used for most city and highway driving.
STARTING AND OPERATING “1” Low This range should be used for maximum engine braking when descending steep grades. In this range, up shifts will occur only to prevent engine over speed while down shifts from 2nd to first will occur as early as possible. AUTOSTICK — IF EQUIPPED Autostick is a driver-interactive transmission that offers manual gear shifting capability to provide you with more control.
STARTING AND OPERATING Autostick General Information • The transmission will automatically upshift from first to second gear and from second to third gear when engine speed reaches about 6300 RPM. • Downshifts from third to second gear above 74 mph (119 km/h) and from second to first gear above 41 mph (66 km/h) will be ignored. • You can start out in first, second, or third gear. Shifting into fourth gear can occur only after vehicle speed reaches 15 mph (24 km/h).
STARTING AND OPERATING MANUAL TRANSAXLE OPERATION WARNING! You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied. The parking brake should always be applied when the driver is not in the vehicle, especially on an incline. Fully depress the clutch pedal before you shift gears. As you release the clutch pedal, lightly depress the accelerator pedal. Use each gear in numerical order - do not skip a gear.
STARTING AND OPERATING Never drive with your foot resting on the clutch pedal, or try to hold the vehicle on a hill with the clutch pedal partially engaged. This will cause abnormal wear on the clutch. 289 2.4 Liter Turbo— If Equipped Never shift into REVERSE until the vehicle has come to a complete stop. NOTE: During cold weather, until the transaxle lubricant is warm, you may experience slightly higher shift efforts. This is normal and not harmful to the transaxle.
STARTING AND OPERATING the shifter lever all the way to the right to avoid accidentally selecting THIRD gear. Also, use care when selecting FIRST gear to avoid accidentally selecting REVERSE. Recommended Shift Speeds To use your manual transaxle for optimal fuel economy, it should be upshifted as listed in table 1. When moving the shifter lever into REVERSE press the lever to the left until the resistance is overcome.
STARTING AND OPERATING For improved performance, your manual transaxle may be upshifted up to the maximum speeds listed in table 2 (within legal speed limits). TABLE 2-MANUAL TRANSAXLE MAXIMUM PERFORMANCE SHIFT SPEEDS IN mph (km/h) ENGINE 1 to 2 2 to 3 3 to 4 4 to 5 SIZE 30 60 85 115 2.4L (48) (97) (136) (185) If you exceed these speeds, you may notice the engine cut in and out. This is caused by an electronic limiter in the engine computer. The engine will run normally when you reduce engine speed.
STARTING AND OPERATING PARKING BRAKE When the parking brake is applied with the ignition on, the Brake Light in the instrument cluster will come on. NOTE: This light only shows that the parking brake is on. It does not show the degree of brake application. slightly on the lever, then depress the button on the end of the lever and push the lever fully down toward the floor. NOTE: The parking brake lever will not release unless the lever is pulled up slightly past its applied position.
STARTING AND OPERATING When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the automatic transaxle locking mechanism may make it difficult to move the selector out of Park. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on a uphill grade. You should always apply the parking brake before leaving the vehicle.
STARTING AND OPERATING If either of the two hydraulic systems lose normal capability, the remaining system will still function with some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop. In addition, if the malfunction is caused by an internal leak, as the brake fluid in the master cylinder drops, the brake warning indicator will light.
STARTING AND OPERATING WARNING! • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING When the vehicle is driven over 7 mph (11 km/h), you may also hear a slight clicking sound as well as some related motor noises. These noises are the system performing its self check cycle to ensure that the ABS system is working properly. This self check occurs each time the vehicle is started and accelerated past 7 mph (11 km/h). • and a slight drop or fall away of the brake pedal at the end of the stop.
STARTING AND OPERATING POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these conditions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.
STARTING AND OPERATING TRACTION CONTROL — IF EQUIPPED The Traction Control System will improve acceleration and steering on slippery surfaces by reducing tire spin. The system reduces wheel slip and maintains traction at the driving (front) wheels by engaging the brake on the wheel that is losing traction. When this occurs the TRAC indicator light located above the instrument cluster odometer will flash. The system operates at speeds below 35 mph (56 km/h).
STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings 299 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • LT (Light Truck)-Metric tire sizing is based on U.S. design standards.
STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING 301 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (i.e. tire pressure, vehicle loading, road conditions, and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure 303 Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar.
STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information” placard and in the “Vehicle Loading” section of this manual.
STARTING AND OPERATING 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. 307 1. Safety— WARNING! • Improperly inflated tires are dangerous and can cause accidents. • Under inflation increases tire flexing and can result in tire failure.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation, also increases tire rolling resistance and results in higher fuel consumption. maximum loaded vehicle condition. These pressure conditions will be found in the “Supplemental Tire Pressure Information” section of this manual. 3.
STARTING AND OPERATING 309 check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. Check tire pressures more often if subject to a wide range of outdoor temperatures, as tire pressures vary with temperature changes. CAUTION! Tire pressures change by approximately 1 psi (7 kPa) per 12° F (7° C) of air temperature change.
STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high-speed vehicle operation.
STARTING AND OPERATING Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Always use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels). Never combine them with other types of tires. Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
STARTING AND OPERATING Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result.
STARTING AND OPERATING WARNING! The limited use spare tires are for emergency use only. Installation of this limited use spare tire affects vehicle handling. With this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly. Replace (or repair) the original tire at the first opportunity and reinstall it on your vehicle. Failure to do so could result in loss of vehicle control.
STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. Many states have laws requiring tire replacement at this point. Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! These indicators are molded into the bottom of the tread grooves.
STARTING AND OPERATING Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
STARTING AND OPERATING CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. Alignment And Balance Poor suspension alignment may result in: • Fast tire wear. • Uneven tire wear, such as feathering and one-sided wear. • Vehicle pull to right or left. Tires may also cause the vehicle to pull to the left or right. Alignment will not correct this condition. See your dealer for proper diagnosis.
STARTING AND OPERATING SNOW TIRES Some areas of the country require the use of snow tires during winter. Standard tires are of the all season type and satisfy this requirement as indicated by the M+S designation on the tire side wall. If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of 4, failure to do so may adversely affect the safety and handling of your vehicle.
STARTING AND OPERATING wear should be corrected before rotating. The suggested rotation method is the “forward-cross” shown in the diagram. FUEL REQUIREMENTS 2.4L Standard Engine and 2.4L Standard Turbo Engine Your vehicle is designed to meet all emission regulations and provide excellent fuel economy when using high quality regular unleaded gasoline with an octane rating of 87. The use of premium gasoline is not recommended.
STARTING AND OPERATING 2.4L High Output Turbo Engine Your engine is designed to meet all emission regulations and provide excellent fuel economy and performance when using high quality unleaded gasoline having an octane rating of 91. The purchase of higher octane is not required. The use of high quality unleaded gasoline having an octane rating of 91 is recommended but not required. High quality unleaded gasoline having a minumum octane rating of 87 may safely be used for your vehicle.
STARTING AND OPERATING The manufacturer supports the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability of engine and fuel system components. Problems that result from using methanol/gasoline blends are not the responsibility of the manufacturer. While MTBE is an oxygenate made from Methanol, it does not have the negative effects of Methanol.
STARTING AND OPERATING It is even more important to look for gasolines without MMT in Canada, because MMT can be used at levels higher than those allowed in the United States. MMT is prohibited in Federal and California reformulated gasolines. Materials Added to Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in additional cost.
STARTING AND OPERATING • The use of fuel additives which are now being sold as octane enhancers is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. • Do not inhale exhaust gases.
STARTING AND OPERATING 323 ADDING FUEL The fuel tank filler tube has a restricting door about 2 inches (50 mm) inside the opening. If using a portable container, it should have a flexible nozzle long enough to force open the restricting door. Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door, on the passenger’s side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle.
STARTING AND OPERATING CAUTION! CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full. CAUTION! WARNING! A poorly fitting gas cap may cause the Malfunction Indicator Light to turn on.
STARTING AND OPERATING NOTE: Tighten the gas cap about 1/4 turn until you hear one click. This is an indication that cap is properly tightened. If the gas cap is not tighten properly, the Malfunction Indicator Light will come on. Be sure the gas cap is tightened every time the vehicle is refueled. WARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
STARTING AND OPERATING VEHICLE LOADING Vehicle Loading Capacities Front Seat Occupants . . . . . . . . . . . . . . . . . . . . . . . 2 Rear Seat Occupants (sedan) . . . . . . . . . . . . . . . . . . 3 Rear Seat Occupants (convertible) . . . . . . . . . . . . . . 2 Luggage . . . . . . . . . . . . . . . . . . . . . . . 115 lbs (52 kg) Rated Vehicle Capacity (sedan) . . . . . . . 865 lb (392 kg) Rated Vehicle Capacity (convertible) . . .
STARTING AND OPERATING Gross Combination Weight Rating (GCWR) The gross combination weight rating (GCWR) is the total permissible weight of your vehicle and trailer when weighed in combination. (Note that GCWR ratings include a 68 kg (150 lbs) allowance for the presence of a driver). Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR.
STARTING AND OPERATING Weight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle. These kind of hitches are the most popular on the market today and they’re commonly used to tow small- and medium-sized trailers.
STARTING AND OPERATING Trailer Hitch Classification Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package. See your dealer for package content. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission Frontal Area Max. GTW (Gross Trailer Wt.) 2.4L N/A and 2.4L 20 Sq. Ft 1000 lbs (454 kg) Turbo/Automatic* 2.4L N/A and 2.4L 20 Sq. Ft. 1000 lbs (454 kg) Turbo/Manual* * N/A (Naturally Aspirated) Refer to local laws for maximum trailer towing speeds.
STARTING AND OPERATING 331 Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents.
STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information placard in the Tire Safety Information Section of this manual for the maximum combined weight of occupants and cargo for your vehicle.
STARTING AND OPERATING WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident. • When hauling cargo or towing a trailer, do not overload your vehicle or trailer.
STARTING AND OPERATING 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing Requirements — Tires − Do not attempt to tow a trailer while using a compact spare tire. − Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 335 CAUTION! WARNING! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident.
STARTING AND OPERATING NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 7- Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic.
STARTING AND OPERATING Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance and extend transmission life by reducing excessive shifting and heat build up. This action will also provide better engine braking.
STARTING AND OPERATING Towing Tips — Cooling System To reduce potential for engine and transmission overheating, take the following actions: RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) − City Driving When stopped for short periods of time, put transmission in neutral but do not increase engine idle speed. Towing This Vehicle Behind Another Vehicle (Flat towing with all four wheels on the ground) Recreational towing on vehicle’s equipped with automatic transaxle’s is not recommended.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 340 䡵 Driving On Slippery Surfaces . . . . . . . . . . . . . . 349 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . . 340 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . . 349 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . . 342 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and the vehicle locked. NOTE: With extended use, the flasher may wear down your battery. Hazard Warning Switch The flasher switch is located on the instrument panel, below the radio. Depress the switch and both cluster indicators and all front and rear directional signals will flash.
WHAT TO DO IN EMERGENCIES the normal range. If the pointer remains on the H (red) mark for more than a minute, turn the engine off immediately and call for service. NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat.
WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, refer to Section 7, Maintenance, of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous.
WHAT TO DO IN EMERGENCIES Jack Location The jack and jack-handle are stowed behind the right rear side trim panel in the cargo area. 343 Spare Tire Stowage The compact spare tire is stowed under the rear of the vehicle by means of a hook/basket mechanism. To remove or stow the compact spare, use the jack handle to rotate the “spare tire drive” nut. The nut is located under the rear scuff plate at the right rear of the cargo area, just inside the liftgate opening.
WHAT TO DO IN EMERGENCIES Spare Tire Removal Lift up the cover and fit the jack-handle over the drive nut. Rotate the nut to the left until you can remove the swivel hook from the stowage basket. Swing the basket down to remove the compact spare tire. CAUTION! The hook is designed for use with the jack handle only. Use of an air wrench or other power tools is not recommended and can damage the winch.
WHAT TO DO IN EMERGENCIES Jacking Instructions 1. Remove the scissors jack and lug wrench from the stowage bag. NOTE: If equipped with a center cap that covers the wheel nuts, pry off the cap using the small end of the lug wrench. To reinstall the cap, make sure it is properly lined up before pushing it on to the wheel. 345 3. There are two front jacking locations on each side of the body and rear jacking locations located on the trailing arm bracket under the triangular cut out symbol.
WHAT TO DO IN EMERGENCIES Do not raise the vehicle until you are sure the jack is securely engaged. 4. Raise the vehicle by turning the jack screw to the right, using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it.
WHAT TO DO IN EMERGENCIES 100 ft. lbs (135 N·m). If you doubt that you have tightened the nuts correctly, have them checked with a torque wrench by your dealer or at a service station. 8. Remove the wheel blocks and lower the jack until it is free. Stow the lug wrench, and jack in their designated location. Secure all parts using the means provided. WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle.
WHAT TO DO IN EMERGENCIES WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from another vehicle. This type of start can be dangerous if done improperly, so follow this procedure carefully. 1.
WHAT TO DO IN EMERGENCIES WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush the contaminated area immediately with large quantities of water. A battery generates hydrogen gas which is flammable and explosive. Keep flame or spark away from the vent holes.
WHAT TO DO IN EMERGENCIES WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have an accident. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet, mud, loose sand, etc.). 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5.
WHAT TO DO IN EMERGENCIES WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed.
WHAT TO DO IN EMERGENCIES All Transaxles CAUTION! If the vehicle being towed requires steering, the ignition switch must be in the ACCESSORY position, not in the LOCK positions. Do not attempt to use sling type equipment when towing. When securing vehicle to flat bed truck, do not attach to front or rear suspension components. Damage to your vehicle may result from improper towing. If it is necessary to use the accessories while being towed (wipers, defrosters, etc.
WHAT TO DO IN EMERGENCIES 353 CONVERTIBLE TOP MANUAL OVERRIDE If your vehicle is experiencing electrical failure (low battery, etc.) and it is necessary to raise the convertible top, perform the following steps: 1. Locate the convertible top motor bypass screw, which is found in the trunk under the convertible top storage area. 2. Turn the screw counterclockwise until the screw stops. This will relieve the hydraulic pressure and allow the convertible top to be raised manually. 6 Bleeder Screw 3.
WHAT TO DO IN EMERGENCIES 5. Pull down and rotate the handle counterclockwise to engage the latches. 6. Raise the handle into the stowed position. 7. Close the convertible top motor bypass screw by turning the screw clockwise until it stops. Tighten the screw securely. NOTE: Failure to tighten the bypass screw securely can cause convertible top operating concerns.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 2.4L Turbo Engine Compartment . . . . . . . . . . . . 358 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 363 䡵 2.4L Engine Compartment . . . . . . . . . . . . . . . . 359 ▫ Drive Belts — Check Condition And Tension . . 367 䡵 Onboard Diagnostic System — OBD II . . . . . . . . 360 ▫ Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . 368 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . . 360 ▫ Ignition Wiring System . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Maintenance-Free Battery . . . . . . . . . . . . . . . . 371 ▫ Manual Transaxle . . . . . . . . . . . . . . . . . . . . . 388 ▫ Air Conditioner Maintenance . . . . . . . . . . . . . 372 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . 389 ▫ Power Steering — Fluid Check . . . . . . . . . . . . 373 ▫ Front Suspension Ball Joints . . . . . . . . . . . . . . 374 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 357 ▫ Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . 401 ▫ Center High Mounted Stop Light . . . . . . . . . . 404 ▫ Front Park/Turn Signal/Side Marker Lights . . 402 䡵 Fluids And Capacities . . . . . . . . . . . . . . . . . . . 404 ▫ Front Fog Lights — If Equipped . . . . . . . . . . . 402 䡵 Fluids, Lubricants And Genuine Parts . . . . . . . . 405 ▫ Tail/Stop, And Rear Turn Signal Lights . . . . . . 402 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 2.
MAINTAINING YOUR VEHICLE 359 2.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem will turn the MIL light off.
MAINTAINING YOUR VEHICLE 5. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine.
MAINTAINING YOUR VEHICLE DEALER SERVICE Your dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight. dipstick. Adding one quart of oil when the reading is at the MIN mark will result in a MAX reading on these engines.
MAINTAINING YOUR VEHICLE • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C). • Trailer towing. • Taxi, Police or delivery service (commercial service). • Off-Road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel.
MAINTAINING YOUR VEHICLE Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API certified and meet the requirements of DaimlerChrysler Material Standard MS-6395. Engine Oil Viscosity (SAE Grade) SAE 5W-30 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy.
MAINTAINING YOUR VEHICLE Materials Added To Engine Oils The manufacture strongly recommends against the addition of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental additives. Disposing of Used Engine Oil Care should be taken in disposing of used engine oil from your vehicle. Used oil, indiscriminately discarded, can present a problem to the environment.
MAINTAINING YOUR VEHICLE Spark Plugs Spark plugs must fire properly to assure engine performance and emission control. New plugs should be installed at the specified mileage. The entire set should be replaced if there is any malfunction due to a faulty spark plug. Refer to the Engine data Label located under the hood for the proper type of spark plug for use in your vehicle. Under normal operating conditions, the catalytic converter will not require maintenance.
MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE Check ventilation hose for indication of damage or plugging deposits. Replace if necessary. Fuel Filter A plugged fuel filter can cause hard starting or limit the speed at which a vehicle can be driven. Should an excessive amount of dirt accumulate in the fuel tank, frequent filter replacement may be necessary. The fuel filters are located inside the fuel tank. See your dealer for service.
MAINTAINING YOUR VEHICLE Maintenance-Free Battery You will never have to add water, nor is periodic maintenance required. CAUTION! When servicing the battery, always reinstall the battery thermowrap. The thermowrap provides battery heat protection and will extend overall battery life. Failure to reinstall the thermowrap can result in evaporative loss of the battery fluid. 371 WARNING! Battery fluid is a corrosive acid solution and can burn or even blind you.
MAINTAINING YOUR VEHICLE CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion. Apply grease to posts and clamps after tightening.
MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information book for further warranty information. • The air conditioning system contains refrigerant under high pressure.
MAINTAINING YOUR VEHICLE WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Fluids, Lubricants, and Genuine Parts for correct fluid types.
MAINTAINING YOUR VEHICLE 375 Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non abrasive cleaner or use the washer solvent. This will remove accumulations of salt, waxes or road film and help reduce streaking and smearing. Windshield Wiper Blade Replacement Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades.
MAINTAINING YOUR VEHICLE Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system, or if exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged; have a competent technician inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position. • You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool.
MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of old antifreeze solution.
MAINTAINING YOUR VEHICLE Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Years or 100,000 miles before replacement. To prevent reducing this extended maintenance period, it is important that you use the same coolant throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) coolant.
MAINTAINING YOUR VEHICLE WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
MAINTAINING YOUR VEHICLE Points To Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment. This is normally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vaporized when the thermostat opens, allowing hot coolant to enter the radiator.
MAINTAINING YOUR VEHICLE Hoses And Vacuum/Vapor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage. Hard or soft spots, brittle rubber, cracking, tears, cuts, abrasions, and excessive swelling indicate deterioration of the rubber Pay particular attention to the hoses nearest to high heat sources such as the exhaust manifold. Inspect hose routing to be sure hoses do not touch any heat source or moving component that may cause heat damage or mechanical wear.
MAINTAINING YOUR VEHICLE 383 WARNING! Inspect all hose clamps and couplings to make sure they are secure and no leaks are present. Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency. Insure nylon tubing in these areas has not melted or collapsed.
MAINTAINING YOUR VEHICLE WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning lamp is on. Be sure to clean the top of the master cylinder area before removing the cap.
MAINTAINING YOUR VEHICLE 385 WARNING! WARNING! Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident. Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter.
MAINTAINING YOUR VEHICLE refer to Fluids, Lubricants and Genuine Parts for correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid. Fluid Level Check The fluid level in the automatic transaxle should be checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly reduce the life of the transaxle and of the fluid.
MAINTAINING YOUR VEHICLE 5. Remove the dipstick and determine if the fluid is hot or warm. Hot fluid is approximately 180°F (82°C), which is the normal operating temperature after the vehicle has been driven at least 24 km (15 miles). The fluid cannot be comfortable held between the finger tips. Warm is when the fluid is between 85° to 125°F (29° to 52°C). 6. Wipe the dipstick clean and reinsert until seated. Remove dipstick and note reading. 387 CAUTION! Do not overfill.
MAINTAINING YOUR VEHICLE Maintenance schedule “B”—All Engines – Every 60,000 miles (100 000 km) change fluid and filter under the following conditions: • Police, taxi, limousine, commercial type operation, or trailer towing where the vehicle is driven regularly for more than 45 minutes of continuous operation. NOTE: Refer to Section 8 of this manual for maintenance schedules. If the transaxle is disassembled for any reason, the fluid and filter should be changed.
MAINTAINING YOUR VEHICLE Frequency Of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless the following conditions exist: • The lubricant has become contaminated with water. If contaminated with water, the fluid should be changed immediately. • If severe usage has occurred, refer to Maintenance Schedule “B” in Section 8 of this manual.
MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using Mopar Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar or other similar deposits have accumulated on your vehicle, use Mopar Super Kleen Bug and Tar Remover to remove. • Use Mopar Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint.
MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.
MAINTAINING YOUR VEHICLE • For grease stains, apply Mopar威 Multi-purpose cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • Do not use any solvents or protectants on Yes Essentials products. Interior Care Use Mopar Total Clean to clean fabric upholstery and carpeting. Use Mopar Total Clean to clean vinyl upholstery. Mopar Total Clean is specifically recommended for leather upholstery.
MAINTAINING YOUR VEHICLE To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Glass Surfaces All glass surfaces should be cleaned on a regular basis with Mopar Glass Cleaner or any commercial householdtype glass cleaner. Never use an abrasive type cleaner.
MAINTAINING YOUR VEHICLE Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the car to wash them. Replace the belts if they appear frayed or worn or if the buckles do not work properly. Dry with a soft tissue. CONVERTIBLE TOP CARE Immediate removal of any contaminant is recommended.
MAINTAINING YOUR VEHICLE CAUTION! Never use an abrasive type cleaner or bleaches. Cleaners should not contain silicones, organic solvents, petroleum distillates or plasticizers. always wait until the top is thoroughly dry before lowering it into the storage area. Scrub in all directions, covering an area of about two square feet at a time. Avoid heavy scrubbing. Rinse the entire vehicle with water to remove all soap and dirt from the top fabric and to prevent streaking on painted and chrome surfaces.
MAINTAINING YOUR VEHICLE CAUTION! Avoid getting Scotchguard_ on the surrounding weather strips, moldings, paint, or glass. Damage to these items might occur. INTEGRATED POWER MODULE (IPM) An Integrated Power Module is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. A description of each fuse and component may be stamped on the inside of the cover.
MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 1 40 Amp Green 2 20 Amp Yellow 3 10 Amp Red 4 10 Amp Red 5 20 Amp Yellow 6 10 Amp Red 7 8 30 Amp Green 30 Amp Green Description Power Top Feed AWD ECU Feed CHMSL Brake Switch Feed Ignition Switch Feed Trailer Tow IOD Sw/Pwr Mir/ Ocm Steering Cntrl Sdar/Hfm IOD Sense1 IOD Sense2 Cavity Cartridge Mini Fuse Fuse 9 40 Amp Green 10 20 Amp Yellow 11 15 Amp Lt Blue 12 20 Amp Yellow 13 20 Amp Yellow 14 10 Amp Red 15 50 Amp Red 16 15 Amp Lt.
MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 17 10 Amp Red 18 40 Amp Green 19 20 Amp Yelow 20 15 Amp Lt. Blue 21 10 Amp Red 22 10 Amp Red 23 15 Amp Lt. Blue 24 25 Amp Natural Description IOD Feed CVT Mod/ Mod_Wcm ASD Relay Contact PWR Feed PWR Amp 1 & Amp 2 Feed IOD Feed Radio IOD Feed Intrus Mod/Siren IGN RUN Hvac/ Compass Sensor ENG ASD Relay Feed 3 PWR Sunroof Feed Cavity Cartridge Mini Fuse Fuse 25 10 Amp Red 26 15 Amp Lt.
MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 33 10 Amp Red 34 30 Amp Pink 35 40 Amp Green 36 30 Amp Pink 37 25 Amp Natural Description ABS MOD/J1962 Conn/PCM ABS Valve Feed ABS Pump Feed Headlamp Washer Control Spare 399 CAUTION! • When installing the Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure.
MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you will not be using your vehicle for more than 21 days you may want to take steps to preserve your battery. You may: • Disengage the mini fuse in the Power Distribution Center labeled IOD (Ignition Off-Draw). • Or, disconnect the negative cable from the battery. REPLACEMENT BULBS LIGHT BULBS — Inside Bulb No. Center Console Floor Lamp . . . . . . . . . . . . . . . . . T37 Climate Controls . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 401 BULB REPLACEMENT Headlights CAUTION! Do not touch the new headlight bulb with your fingers. Oil contamination will severely shorten bulb life. 1. Remove the headlight access cover splash shield, located in the front wheel well opening. 2. Disconnect the electrical connector. 3. Rotate the socket to the left one quarter turn and replace the bulb.
MAINTAINING YOUR VEHICLE Front Park/Turn Signal/Side Marker Lights Front Fog Lights — If Equipped 1. Remove the headlight access cover splash shield, located in the front wheel well opening. 1. Remove the fasteners attaching the lower splash shield to gain access to the fog light. 2. Rotate the socket to the left one quarter turn to replace and replace the bulb. 2. Twist and remove the bulb from the fog light housing. 3. Disconnect the electrical connector and replace bulb.
MAINTAINING YOUR VEHICLE 403 Back Up Lights 3. Pull the bulb out of the socket and replace. Removing Backup Light Bulbs 1. To remove the backup lamp, you must take a fiber stick and slide it along the inboard side of the lamp and compress a spring clip to allow it to partially ⬙pop⬙ out to the secondary catch.
MAINTAINING YOUR VEHICLE 2. Fully compress the clip to get the lamp to come out completely. 3. Remove the socket from the housing. 4. Pull the bulb out of the socket and replace. Center High Mounted Stop Light 1. Open the liftgate and remove the liftgate CHMSL cover. 2. Remove CHMSL lens from the housing by unlatching the two side latches. 3. Pull the bulb out of the socket and replace. FLUIDS AND CAPACITIES Fuel (Approximate) Engine Oil-With Filter 2.
MAINTAINING YOUR VEHICLE 405 FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluids, Lubricants and Genuine Parts Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Use API Certified SAE 5W-30 Engine Oil. Refer to your engine oil filler cap for correct SAE grade meeting DaimlerChrysler Material Standard MS-6395. Non Turbo—Mopar 4105409AB or equiv.
MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Fluid. Manual Transmission Fluid. Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar威 ATF+4 Automatic Transmission Fluid. Mopar威 ATF+4 Automatic Transmission Fluid. Mopar威 DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids or equivalent.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . . . 408 ▫ Schedule “A”—Non Turbo . . . . . . . . . . . . . . . 422 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . . 408 ▫ Schedule “A”—Turbo . . . . . . . . . . . . . . . . . . 427 C ▫ Schedule “B”—All Engines . . . . . . . . . . . . . .
M A I N T E N A N C E 408 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES • Taxi, police, or delivery service (commercial service).†〫 • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow schedule “B—All Engines” of the ⬙Maintenance Schedules⬙ section of this manual.
M 410 MAINTENANCE SCHEDULES A I At Each Stop for Fuel N T • Check the engine oil level about 5 minutes after a fully E warmed engine is shut off. Checking the oil level while N A the vehicle is on level ground will improve the accuN racy of the oil level reading. Add oil only when the C level is at or below the ADD or MIN mark. E S C H E D U L E S 8 • Check the windshield washer solvent and add if required. • Check all lights and all other electrical items for correct operation.
SCHEDULE “B”—ALL ENGINES SCHEDULE “B”—ALL ENGINES Follow schedule “B”—All Engines if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (100 000 km) if the vehicle is usually operated under one or more of the conditions marked with an 〫. Change the manual transaxle fluid every 48,000 miles (80 000 km) if the vehicle is usually operated under one or more of the conditions marked with an †.
M A I N T E N A N C E 412 SCHEDULE “B”—ALL ENGINES NOTE: IF ANY of these apply to you then flush and replace the engine coolant every 102,000 miles (170 000 km) or 60 months, whichever comes first, and follow schedule “B—All Engines” of the ⬙Maintenance Schedules⬙ section of this manual.
SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter, replace as necessary.* Inspect the Make-up air filter, replace as necessary.
M 414 SCHEDULE “B”—ALL ENGINES A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace as necessary.* Replace the Make-up air filter. Adjust the generator drive belt tension.
SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Change the brake fluid. If vehicle is used for trailer towing. Inspect the engine air cleaner filter, replace as necessary.* Change the manual transaxle fluid.† Inspect the Make-up air filter. Replace as necessary.
M 416 SCHEDULE “B”—ALL ENGINES A I N Miles T ( Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Replace the Make-up air filter. Adjust the generator drive belt tension.
SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter and replace as necessary.* Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Inspect the Make-up air filter, replace as necessary. Adjust the generator drive belt tension.
M 418 SCHEDULE “B”—ALL ENGINES A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not reA placed at 3 months. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Change the brake fluid. If vehicle is used for trailer towing. Inspect the engine air cleaner filter and replace as necessary.* Change the manual transaxle fluid.† Replace the engine timing belt. * Flush and replace the engine coolant, if not replaced at 60 months.
SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. * Inspect the tie rod ends and boot seals. Replace the Make-up air filter. Adjust the generator drive belt tension. Change automatic transaxle fluid and filter.〫 Inspect the PCV valve and replace if necessary. *‡ Flush and replace the engine coolant at 120 months, if not replaced at 102,000 miles.
M 420 SCHEDULE “B”—ALL ENGINES A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not reA placed at 3 months. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Inspect the engine air cleaner filter and replace as necessary.
SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. * Replace the spark plugs. Replace the Make-up air filter. Inspect the PCV valve and replace if necessary. *‡ 138,000 (230 000) X * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emissions warranty. ‡ This maintenance is not required if previously replaced.
M 422 SCHEDULE “A”—NON TURBO A I SCHEDULE “A”—NON TURBO N T Miles E N (Kilometers) A [Months] N C Change engine oil and engine oil filter. E Rotate tires. S C H E D U L E S 8 Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the Make-up air filter.
SCHEDULE “A”—NON TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace, if necessary.* Flush and replace the engine coolant at 60 months, if not done at 102,000 miles. Replace the Make-up air filter. Adjust the generator drive belt tension.
M 424 SCHEDULE “A”—NON TURBO A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Replace the engine air cleaner filter. Replace the spark plugs. Replace the engine timing belt. * Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Replace the Make-up air filter. Adjust the generator drive belt tension.
SCHEDULE “A”—NON TURBO 425 M Miles 108,000 114,000 120,000 126,000 132,000 138,000 (Kilometers) (180 000) (190 000) (200 000) (210 000) (220 000) (230 000) [Months] [108] [114] [120] [126] [132] [138] Change engine oil and engine oil filter. X X X X X X Rotate tires. X X X X X X Inspect the PCV valve and replace if necessary. * X ‡ Replace the air cleaner filter. X Flush and replace the engine coolant at 120 X months, if not done at 102,000 miles. Replace the spark plugs and ignition cables.
M 426 SCHEDULE “A”—NON TURBO A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Inspect the PCV valve and replace if necessary. * ‡ S C H E D U L E S 8 Replace the air cleaner filter. * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emissions warranty. 144,000 (240 000) [144] X X 150,000 (250 000) [150] X X X X ‡ This maintenance is not required if previously replaced.
SCHEDULE “A”—TURBO 427 M SCHEDULE “A”—TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the Make-up air filter. Adjust the generator drive belt tension.
M 428 SCHEDULE “A”—TURBO A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Flush and replace engine coolant at 60 months, if not replaced at 100,000 miles.
SCHEDULE “A”—TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Replace the Make-up air filter. Adjust the generator drive belt tension.
M 430 SCHEDULE “A”—TURBO A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Replace the engine air cleaner filter. Replace the spark plugs. Adjust the generator drive belt tension. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Flush and replace the engine coolant if not done at 60 months. Replace the Make-up air filter.
SCHEDULE “A”—TURBO Miles (Kilometers) [Month] Change engine oil and engine oil filter. Rotate tires. Inspect the PCV Valve and replace if necessary. * Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emissions warranty. ‡ This maintenance is not required if previously replaced.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434 ▫ Prepare For The Appointment . . . . . . . . . . . . 434 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 434 䡵 Reporting Safety Defects . . . . . . . . . . . . . . . . . . 437 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 437 䡵 Publication Order Forms . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
IF YOU NEED CONSUMER ASSISTANCE WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.
IF YOU NEED CONSUMER ASSISTANCE Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration.
IF YOU NEED CONSUMER ASSISTANCE on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
INDEX 10
INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . 294 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 379 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 323 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 274 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 321 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 370 Air Conditioner Maintenance . . . . . . . . . . . . . . . 372 Air Conditioning Controls . . . . . . . . . . . . . .
INDEX Special Additives . . . . . . . . . . . . . . . . . . . . . . 388 Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286 Back-Up Lights . . . . . . . . . . . . . . . . . . . . . . . . . 403 Ball Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371 Keyless Transmitter Replacement (RKE) . . . . . 28,34 Belts, Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367 Belts, Engine . . . . .
INDEX Caution, Exhaust Gas . . . . . . . . . . . . . . . . . . . . . 112 CD (Compact Disc) Player . . . . . . . . . . . . . . . 238,246 CD (Compact Disc) Player Maintenance . . . . . . . . 264 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . 134,265 Center High Mounted Stop Light . . . . . . . . . . . . 404 Chains, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . . 342 Chart, Tire Sizing . . . . . . . . . . . . .
INDEX Coolant Level . . . . . . . . . . . . . . . . . . . . . . 377,380 Disposal of Used Coolant . . . . . . . . . . . . . . . . 380 Drain, Flush, and Refill . . . . . . . . . . . . . . . . . . 378 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . 380 Points to Remember . . . . . . . . . . . . . . . . . 379,381 Pressure Cap . . . . . . . . . . . . . . . . . . . . . . . . . 379 Selection of Coolant (Antifreeze) . . . . . . . . . . . 378 Corrosion Protection . . . . . . . . . . . . . . . . . .
INDEX Electronic Speed Control (Cruise Control) . . . . . . 187 Electronic Vehicle Information Center (EVIC) . . . . 227 Emergency Deck Lid Release Latch (Convertible) . . 41 Emergency, In Case of Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 347 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351 Emergency Seat Back Release (Sedan) . . . . . . . . . . 39 Emission Control System Maintenance . . . .
INDEX Flooded Engine Starting . . . . . . . . . . . . . . . . . . . 280 Fluid, Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . 406 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . . 404 Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Fluid Level Checks Automatic Transaxle . . . . . . . . . . . . . . . . . . . . 386 Fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405 Fluids, Lubricants and Genuine Parts . . . . . . . . . .
INDEX Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . 320 Gauges Coolant Temperature . . . . . . . . . . . . . . . . . . . . 220 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 221 Gearshift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283 General Information . . . . . . . . . . . . . . . . . . . . . .
INDEX Instrument Cluster . . . . . . . . . . . . . . . . . . . . 217,220 Instrument Panel and Controls . . . . . . . . . . . . . . 216 Instrument Panel Cover . . . . . . . . . . . . . . . . . . . 393 Instrument Panel Lens Cleaning . . . . . . . . . . . . . 393 Integrated Power Module (Fuses) . . . . . . . . . . . . 396 Interior Appearance Care . . . . . . . . . . . . . . . . . . 392 Intermittent Wipers (Delay Wipers) . . . . . . . . . . . 184 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Engine Temperature Warning . . . . . . . . . . . . . . 224 Fog . . . . . . . . . . . . . . . . . . . . . . . . . . 180,225,402 Front Replacement . . . . . . . . . . . . . . . . . . . . . 401 Headlight Switch . . . . . . . . . . . . . . . . . . . . . . 179 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 High Beam Indicator . . . . . . . . . . . . . . . . . . . . 226 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . 179 Lights On Reminder . . . . . . . . . . . . . .
INDEX Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . . 411 Schedule “B”-All Engines . . . . . . . . . . . . . . . . 411 Maintenance Schedules . . . . . . . . . . . . . . . . . . . . 408 Malfunction Indicator Light (Check Engine) . . 222,361 Manual Override, Convertible Top . . . . . . . . . 130,353 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . 438 Manual Transaxle . . . . . . . . . . . . . . . . . . 279,288,388 Downshifting . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366 Recommendation . . . . . . . . . . . . . . . . . . . 366,404 Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366 Viscosity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366 Oil Pressure Light . . . . . . . . . . . . . . . . . . . . . . . 226 Onboard Diagnostic System . . . . . . . . . . . . . . 360,361 Opener, Garage Door (HomeLink威) . . . . . . . . . . . 190 Operator Manual (Owner’s Manual) . . . .
INDEX Pretensioners Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 52,85 Programmable Electronic Features . . . . . . 192,196,231 Programming Transmitters (Remote Keyless Entry) . . . . . . . . . . . . . 26,33,192,196 Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . . 311 Radio Broadcast Signals . . . . . . . . . . . . . . . . . . . 237 Radio Operation . . . . . . . . . . . . . . . . . . . 238,246,265 Radio, Satellite . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Safety Information, Tire . . . . . . . . . . . . . . . . . . . 299 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Satellite Radio . . . . . . . . . . . . . . . . . . . . . . . . . . 260 Satellite Radio Antenna . . . . . . . . . . . . . . . . . . . 263 Schedule, Maintenance . . . . . . . . . . . . . . . . . . . . 408 Seat Belt Maintenance . . . . . . . . . . . . . . . . . . . . 394 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . .
INDEX Sentry Key (Immobilizer) . . . . . . . . . . . . . . . . . 15,36 Sentry Key Programming . . . . . . . . . . . . . . . . . . . 17 Service and Maintenance . . . . . . . . . . . . . . . . . . 408 Service Assistance . . . . . . . . . . . . . . . . . . . . . . . 434 Service Contract . . . . . . . . . . . . . . . . . . . . . . . . . 436 Service Manuals . . . . . . . . . . . . . . . . . . . . . . . . 438 Setting the Clock . . . . . . . . . . . . . . . . . . 236,240,248 Settings, Personal . . . . . . . . . .
INDEX Tether Anchor, Child Restraint . . . . . . . . . . . . 74,107 Theft Alarm (Security Alarm) . . . . . . . . . . . . . . . . 35 Theft System (Security Alarm) . . . . . . . . . . . . . . . 35 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . . 185 Tire and Loading Information Placard . . . . . . . . . 303 Tire Identification Number (TIN) . . . . . . . . . . . . . 302 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . 299 Tire Safety Information . . . . . . . . . . . . . .
INDEX Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330 Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 Traction Control . . . . . . . . . . . . . . . . . . . . . . 185,298 Traction Control Switch . . . . . . . . . . . . . . . . . 185,298 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . 326 Cooling System Tips . . . . . . . . . . . . . . . . . . . . 338 Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Uniform Tire Quality Grades . . Universal Transmitter . . . . . . . Unleaded Gasoline . . . . . . . . . Untwisting Procedure, Seat Belt ............. ............. ............. ............ . 439 . 190 . 318 51,85 Vacuum/Vapor Harnesses . . . . . . . . . . . . . . . . . 382 Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . 133 Variance, Compass . . . . . . . . . . . . . . . . . . . . . . . 234 Vehicle Identification Number (VIN) . . . . . . . . . . . . 6 Vehicle Loading . .
