First Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
TABLE OF CONTENTS SECTION PAGE .............................................................3 1 1 INTRODUCTION 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4 UNDERSTANDING YOUR INSTRUMENT PANEL 5 STARTING AND OPERATING 6 WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .357 6 7 MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS m Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m Vehicle Identification Number . . . . . . . . . . . . . . . 6 m How To Use This Manual . . . . . . . . . . . . . . . . . . 4 m Vehicle Modifications/Alterations . . . . . . . . . . . . 7 m Warnings And Cautions . . . . . . . . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the driver’s front corner of the instrument panel, visible through the windshield.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . . .13 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .13 ▫ Locking Doors With A Key . . . . . . . . . . . . . . .14 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .15 m Sentry Keyt — If Equipped . . . . . . . . . . . . . . . .15 ▫ Replacement Keys . . . . . . . . . . . . . . . . . . . . . .16 ▫ Sentry Keyt Programming . . . . . . . . . . . . . . . .17 ▫ General Information .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Unlock The Doors And Liftgate . . . . . . . . . .24 ▫ To Turn Off “Flash Lights With Lock” . . . . . . . .33 ▫ To Lock The Doors And Liftgate — If Equipped With Power Options . . . . . . . . . . . . . . . . . . . .25 ▫ To Program Additional Transmitters . . . . . . . . .33 ▫ Panic Alarm . . . . . . . . . . . . . . . . . . . . . . . . . .26 ▫ To Turn Off “Flash Lights With Lock” . . . . . . . .26 ▫ To Program Additional Transmitters . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE m Emergency Seat Back Release (Sedan) . . . . . . . . .40 m Emergency Deck Lid Release Latch (Convertible) . . . . . . . . . . . . . . . . . . . . . . . . . . .41 m Power Windows . . . . . . . . . . . . . . . . . . . . . . . .42 ▫ Auto Down Feature . . . . . . . . . . . . . . . . . . . .43 ▫ Rear Window Switches . . . . . . . . . . . . . . . . . .43 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . .44 m Occupant Restraints (Sedan) . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Driver And Front Passenger Supplemental Restraint System (SRS) . . . . . . . . . . . . . . . . . . .90 ▫ Child Restraint . . . . . . . . . . . . . . . . . . . . . . . 107 m Engine Break-In Recommendations . . . . . . . . . . 115 m Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . 115 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place. 13 IGNITION KEY REMOVAL Automatic Transaxle Place the shift lever in PARK and make sure that the shift knob push button has returned to the out position.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If you try to remove the key before you place the lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE KEY-IN-IGNITION REMINDER Opening the driver’s door when the key is in the ignition, sounds a signal to remind you to remove the key. NOTE: With the driver’s door open, and the key in the ignition, both the power door locks and Remote Keyless Entry (RKE) will not function. SENTRY KEYT — IF EQUIPPED The Sentry Keyt Immobilizer System prevents unauthorized operation of the vehicle by disabling the engine.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • The Sentry Keyt Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. • Exxon/Mobil Speed Pass,™ additional Sentry Keys, or any other transponder equipped components on the same keychain will not cause a key-related (transponder) fault unless the additional part is physically held against the ignition key being used when starting the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: When having the Sentry Keyt Immobilizer System serviced, bring all vehicle keys with you to the dealer. Sentry KeyT Programming If you have two valid sentry keys, you can program new sentry keys to the system by performing the following procedure: 1. Cut the additional Sentry Keyt Transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the ignition switch.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If a programmed key is lost, see your dealer to have all remaining keys erased from the systems memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to the dealer at the time of service to be reprogrammed. STEERING WHEEL LOCK — IF EQUIPPED Your vehicle may be equipped with a passive steering wheel lock.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: If you turned the wheel to the right to engage the lock, you must turn the wheel slightly to the right to disengage it. If you turned the wheel to the left to engage the lock, turn the wheel slightly to the left to disengage it. 2 Automatic Transaxle Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK and the shift knob push-button is out.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death. POWER DOOR LOCKS — IF EQUIPPED A door lock switch is on each front door panel. Press this switch to lock or unlock the doors. CAUTION! An unlocked vehicle is an invitation to thieves.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 AUTOMATIC DOOR LOCKS — IF EQUIPPED The doors will lock automatically on vehicles with power door locks if all of the following conditions are met: For vehicles not equipped with the EVIC the Automatic Door Locks can be enabled or disabled by performing the following procedure: 1. The Auto Lock feature is enabled. 1. Close all doors and place the key in the ignition. 2. The transmission is in gear. 2.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. The transmission is in NEUTRAL or PARK. 4. The driver door is opened. 5. The doors were not previously unlocked. 6. The vehicle speed is 0 mph (0 km/h). The Auto Unlock feature can be enabled or disabled. Refer to “Personal Settings” (Customer Programmable Features) in the Electronic Vehicle Information Center (EVIC) — if equipped section of this manual.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: For emergency exit with the system engaged, move the lock plunger up (unlocked position), roll down window and open the door with the outside door handle.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY (SEDAN) Three Button Key This system allows you to lock or unlock the doors and liftgate or activate the panic alarm from distances a minimum of 66 feet (20 meters) using a hand held radio transmitter. The transmitter need not be pointed at the vehicle to activate the system. NOTE: The line of transmission must not be blocked with metal objects.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE under “Personal Settings” in the EVIC section of this manual. On non EVIC – equipped vehicles perform the following steps: The system can be programmed to unlock all the doors upon the first UNLOCK button press by using the following procedure: 1. Press and hold the LOCK button on a programmed keyfob. 2. Continue to hold the LOCK button at least four seconds, but not longer than 10 seconds, then press and hold the UNLOCK button.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Information Center (EVIC)” section of this manual. On non EVIC – equipped vehicles perform the following steps: 1. Press the LOCK button for four to ten seconds. 2. While the LOCK button is pressed (after four seconds), press the PANIC button. Release both buttons. The “Sound Horn On Lock” and “Flash Lamps With Lock” feature can be reactivated by repeating this procedure.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. While the UNLOCK button is pressed, (after four seconds) press the LOCK button. Release both buttons. 3. Test the flash lamps with LOCK feature while outside of the vehicle, by pressing the LOCK button on the keyfob with the ignition in the LOCK position, and the key removed. NOTE: Pressing the LOCK button on the keyfob, while you are in the vehicle, will activate the Security Alarm.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Turn the ignition to the ON position Do not start the engine. 12. Repeat steps eight through ten to program up to six additional fobs. 5. Press and hold the UNLOCK button on the keyfob. 13. Turn the ignition to the OFF position. 6. After holding the UNLOCK button for four seconds, also press the PANIC button within six seconds. 14. Your vehicle will remain in program mode up to 60 seconds from when the original chime was heard.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. If your Remote Lock Control fails to operate from a normal distance, check for these two conditions. 29 1. If the keyfob is equipped with a screw, remove the screw. With the transmitter buttons facing down, use a flat blade to pry the two halves of the transmitter apart.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. REMOTE KEYLESS ENTRY (CONVERTIBLE) 3. To assemble the transmitter case, snap the two halves together. NOTE: If the keyfob is equipped with a screw, reinstall and tighten the screw until snug.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TO UNLOCK THE DOORS: Press and release the UNLOCK button on the keyfob once to unlock only the driver’s door or twice to unlock all the doors and liftgate. When the UNLOCK button is pressed, the illuminated entry will initiate, and the parking lights will flash on twice. The time for this feature is programmable on vehicles equipped with the Electronic Vehicle Information Center (EVIC).
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. If the desired programming was not achieved or to reactivate this feature, repeat the above steps. TO LOCK THE DOORS: Press and release the LOCK button on the transmitter to lock all doors. The turn signal lights will flash and the horn will chirp once to acknowledge the lock signal. If desired, the “Sound Horn On Lock” and “Flash Lamps With Lock” feature can be turned on or off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The panic alarm will stay on for three minutes unless you turn it off by pressing the PANIC button a second time or if the vehicle speed is 5 mph (8 km/h) or greater. NOTE: When you turn off the panic alarm by pressing the PANIC button a second time, you may have to be closer to the vehicle due to the radio frequency noises of the system. TO TURN OFF “FLASH LIGHTS WITH LOCK”: NOTE: The Flash Lights With Lock feature can be turned on or off.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Up to eight transmitters can be programmed to your vehicle. To obtain additional transmitters, contact your authorized dealer. To program a transmitter (within 23–50 ft/7–15 m of the vehicle), perform the following procedure: 1. Gather every transmitter that is to be used with the vehicle including any transmitters that are currently programmed. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 TRANSMITTER BATTERY SERVICE NOTE: Perchlorate Material – special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate.” 2 The recommended replacement battery is the Panasonict CR2032 or equivalent. 1. Pry the transmitter halves apart with a dime or similar object. Make sure not to damage the rubber gasket material during removal. Separating Transmitter Halves 2. Remove and replace the batteries.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the keyfob is equipped with a screw, reinstall and tighten the screw until snug. SECURITY ALARM SYSTEM — IF EQUIPPED The system monitors the doors, liftgate, and ignition switch for unauthorized operation. If something triggers the alarm, the system will signal for about 18 minutes. For the first three minutes the horn will sound and the headlights, park lights, tail lights and the indicator light in the cluster will flash.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 To disarm the system: Unlock a front door using the Keyless Entry Transmitter. Starting the vehicle with a valid Sentry key will disarm the system. A valid key is one that is programmed to that particular vehicle. A valid key will disarm the system, an invalid key will trigger the alarm. 2 Tamper Alert If the horn sounds three times when you unlock a front door using the Keyless Entry Transmitter, the alarm has been activated.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To open the unlocked liftgate, squeeze the liftgate release touch pad located on the backside of the liftgate handle and pull the liftgate open with one fluid motion. Opening The Liftgate While the Security Alarm Is Activated Unlocking the liftgate with the remote keyless entry transmitter will allow access to the liftgate without sounding or disarming the security alarm system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Gas props support the liftgate in the open position. However, because the gas pressure drops with temperature, it may be necessary to assist the props when opening the liftgate in cold weather. DECK LID (CONVERTIBLE) Gas props support the deck lid in the open position. However, because the gas pressure drops with temperature, it may be necessary to assist the props when opening the deck lid in cold weather.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE EMERGENCY SEAT BACK RELEASE (SEDAN) WARNING! seat back can be unlatched by pulling down on the glow-in-the-dark lever attached to the left rear seat back latching mechanism. Do not allow children to have access to the liftgate area with the rear shelf panel in position 1 (Top) or position 2 (Middle), either by climbing into the liftgate from outside, or through the inside of the vehicle. Always close the liftgate when your vehicle is unattended.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Make sure that the elastic loop is around the emergency release handle at all times. If the handle is pulled downward, entirely through the elastic loop, the handle will not return to its original position and the seat back may not operate properly. EMERGENCY DECK LID RELEASE LATCH (CONVERTIBLE) As a security measure, an emergency deck lid release lever is built into the deck lid latching mechanism.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE POWER WINDOWS The power window switches are located on the instrument panel above the radio. The top left switch controls the left front window and the top right switch controls the right front window. The lower left switch controls the left rear window and the lower right switch controls the right rear window.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. AUTO DOWN FEATURE The driver’s and passenger’s front window switches have an auto down feature. Press the window switch past the detent, release, and the window will go down automatically.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WIND BUFFETING Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Two people should never be belted into a single seat belt. People belted together can crash into one another in an accident, hurting one another badly. Never use a lap/shoulder belt or lap belt for more than one person, no matter what their size. Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 47 2. The seat belt latch plate is above the back of the front seat, next to your arm.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is worn under your arm is very dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. Latch Plate 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.).
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! The rear center lap/shoulder belt is equipped with a lockout feature to ensure that the rear seat back is in the fully upright and locked position when occupied. If the rear seat back is not fully upright and locked and the rear center lap/shoulder belt can be pulled out of the retractor, the vehicle should immediately be taken to your dealer for service. Failure to follow this warning could result in serious or fatal injury.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 SEAT BELT PRETENSIONERS The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENHANCED SEAT BELT REMINDER SYSTEM (BELTALERTT) If the driver’s or front passenger’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlertt) will alert the driver or front passenger to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 DRIVER AND FRONT PASSENGER SUPPLEMENTAL RESTRAINT SYSTEM (SRS) AIRBAG This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment. WARNING! • Do not drill, cut or tamper with the knee impact blocker panels in any way. • Do not mount any accessories to the knee blocker panel such as alarm lights, stereos, citizens band radios etc.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE empty or is occupied by someone that is classified in the “child9 category. This could be a child, a teenager, or even a small adult. ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during front airbag deployment could cause serious injury. Airbags need room to inflate.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Head/Thorax airbag system (if equipped) consists of the following: • AIRBAG Readiness Light (shared with the front airbag system) • Front Seat— side mounted Head/Thorax Airbags — if equipped • Airbag Control Module (shared with the front airbag system) • Side impact sensors How The Airbag System Works • The Occupant Restraint Controller (ORC) determines if a frontal collision is severe enough to require the airbags to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9Passenger Airbag Disable (PAD) Indicator Light9 in this section). If the ORC detects a malfunction in any part of the system, it turns on the AIRBAG warning light either momentarily or continuously. A single chime will sound if the light comes on again after initial start up. WARNING! Ignoring the AIRBAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Even though this vehicle is equipped with an occupant classification system, children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint (see section on child restraints). Passenger Airbag Disabled Light • The PAD indictor light should not be illuminated when an adult passenger is properly seated in the front passenger seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Passenger Airbag Disable (PAD) System Front Passenger Indicator Light Airbag Status Adult OFF ON Child ON OFF Grocery Bags, ON OFF Heavy Briefcases and Other Relatively Light Objects Empty or Very OFF* OFF Small Objects * Since the system senses weight, some small objects will turn the PAD Indicator Light on. Drivers and adult passengers should verify that the PAD Indicator Light is not illuminated when an adult is riding in the front passenger seat.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE indicates that you should take the vehicle to an authorized dealer. The Airbag Warning Light is turned on whenever there is fault that can affect the operation of the airbag system. If there is a fault present in the PAD Indicator Light the Airbag Warning Light remains illuminated to show that the passenger airbag is turned off until the fault is cleared.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE passenger airbag should be turned off. It also determines the rate of airbag inflation during a collision. • Your vehicle has four Weight Sensors located between the seat and the floor pan. The weight sensors measure applied weight and transfers that information to the OCM. • The Head/Thorax Side Airbags—If Equipped (SRS) are designed to activate only in certain side collisions.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not replace the seat cover with an aftermarket seat cover. • Do not add a secondary seat cover other than those approved by DaimlerChrysler/Mopart. • At no time should any supplemental restraint system (SRS) component or SRS related component or fastener be modified or replaced with any part except those which are approved by DaimlerChrysler/ Mopart.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, front passenger seat belt retractor assembly and Occupant Classification System, replaced by an authorized dealer as soon as possible. Maintaining Your Airbag System WARNING! Modifications to any part of the airbag system could cause it to fail when you need it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 WARNING! WARNING! Do not attempt to modify any part of your advanced airbag system. The airbag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any advanced airbag system service. If your seat including your trim cover and cushion needs to be serviced in any way (including removal or loosening/ tightening of seat attachment bolts), take the vehicle to your authorized dealer.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately. prior to the moment of airbag deployment, or neardeployment, and up to a quarter second of high-speed deceleration data during and/or after airbag deployment or near-deployment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE addition to crash investigations initiated by DaimlerChrysler, such investigations may be requested by customers, insurance carriers, government officials, and professional crash researchers, such as those associated with universities, and with hospital and insurance organizations.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Airbag disable lamp status (if equipped) • 9Time9 of airbag deployment (in terms of ignition cycles and vehicle mileage) • Airbag deployment level (if applicable) • Impact acceleration and angle • Seatbelt status • Brake status (service and parking brakes) • Accelerator status (including vehicle speed) • Engine control status (including engine speed) • Transmission gear selection • Cruise control status • Traction/stability control status • Tire pressure mo
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE weight limit in the rearward-facing direction than infant carriers do, so they can be used rearward-facing by children who weigh more than 9 kg (20 lbs) but are less than one year old. • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward facing child restraint should only be used in a rear seat.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the seat belt has a switchable retractor, please refer to Automatic-Locking Retractor (ALR) in this section. • In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle end of the belt several times to shorten it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors and Tether for CHildren (LATCH) Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tether for CHildren. The LATCH system provides for the installation of the child restraint without using the vehicle seat belt.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child restraints systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the top tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 rearward-facing infant restraints will also be equipped with a tether strap with a hook and means for adjusting the tension in the strap. 2 In general, you will first loosen the adjusters on the lower and tether straps so that you can more easily attach the hook or connector to the lower and tether anchorages. The tether strap should be routed under the center of the head restraint and attached to the tether anchor on the rear of the seat back.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a child restraint top tether strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 OCCUPANT RESTRAINTS (CONVERTIBLE) Some of the most important safety features in your vehicle are the restraint systems. These include: If you will be carrying children too small for adult-size seat belts, your seat belts or the LATCH feature also, can be used to hold infant and child restraint systems. • Front and rear seat belts for all passengers Please pay close attention to the information in this section.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 WARNING! WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Two people should never be belted into a single seat belt. People belted together can crash into one another in an accident, hurting one another badly.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. Removing Slack From Belt 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 WARNING! A belt that is worn under your arm is very dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. Latch Plate To Buckle A belt that is too loose will not protect you as well.
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. The seat belt webbing guide should be used to improve seat belt accessibility. The seat belt can be removed from the guide to allow for easier access to the rear seats.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LAP/SHOULDER SEAT BELT UNTWISTING PROCEDURE Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about six to twelve inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. 3. Slide the latch plate upward over the folded webbing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENHANCED SEAT BELT REMINDER SYSTEM (BELTALERTT) If the driver’s or front passenger’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlertt) will alert the driver or front passenger to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DRIVER AND FRONT PASSENGER SUPPLEMENTAL RESTRAINT SYSTEM (SRS) This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Head/Thorax airbags (if equipped) are located inside the driver and front passenger seats, and their covers are also labeled SRS AIRBAG. 2 NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment. WARNING! • Do not drill, cut or tamper with the knee blocker panel in any way. • Do not mount any accessories to the knee blocker panel such as alarm lights, stereos, citizens band radios etc.
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 empty or is occupied by someone that is classified in the “child” category. This could be a child, a teenager, or even a small adult. ride properly buckled up in the rear seat. Never allow children to slide the shoulder belt behind them or under their arm. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag.
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! The front airbag system consists of the following: • Occupant Restraint Controller • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Head/Thorax airbag system (if equipped) consists of the following: • AIRBAG Readiness Light (shared with the front airbag system) • Front Seat— side mounted Head/Thorax Airbags — if equipped • Airbag Control Module (shared with the front airbag system) • Side impact sensors How The Airbag System Works • The Occupant Restraint Controller (ORC) determines if a frontal collision is severe enough to require the airbags to inflate.
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9Passenger Airbag Disable (PAD) Indicator Light9 in this section). If the ORC detects a malfunction in any part of the system, it turns on the AIRBAG warning light either momentarily or continuously. A single chime will sound if the light comes on again after initial start up. WARNING! Ignoring the AIRBAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE objects are placed on the seat, the passenger air bag will not inflate even though the PAD indicator lamp is not illuminated. 97 For all other occupants, the PAD indicator light will be illuminated indicating that the front passenger airbag is turned off and will not inflate.
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Passenger Airbag Disable (PAD) System Front Passenger Indicator Light Airbag Status Adult OFF ON Child ON OFF Grocery Bags, ON OFF Heavy Briefcases and Other Relatively Light Objects Empty or Very OFF* OFF Small Objects * Since the system senses weight, some small objects will turn the PAD Indicator Light on. Drivers and adult passengers should verify that the PAD Indicator Light is not illuminated when an adult is riding in the front passenger seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE indicates that you should take the vehicle to an authorized dealer. The Airbag Warning Light is turned on whenever there is fault that can affect the operation of the airbag system. If there is a fault present in the PAD Indicator Light the Airbag Warning Light remains illuminated to show that the passenger airbag is turned off until the fault is cleared.
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Your vehicle has four Weight Sensors located between the seat and the floor pan. The weight sensors measure applied weight and transfers that information to the OCM. • The Head/Thorax Airbag and Supplemental Restraint Systems are designed to activate only in certain side collisions. The ORC module determines if a side collision is severe enough to require the Head/Thorax airbags to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not add a secondary seat cover other than those approved by DaimlerChrysler/Mopar. • At no time should any supplemental restraint system (SRS) component or SRS related component or fastener be modified or replaced with any part except those which are approved by DaimlerChrysler/ Mopar.
102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! NOTE: Perchlorate Material – special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate.” • Do not place or hang any items such as add-on video players on the right front passenger seat back. The additional weight may cause the Occupant Classification System to be unable to correctly classify the right front occupant. This could allow the passenger frontal airbag to inflate when it is not desired.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Event Data Recorder (EDR) In the event of an accident, your vehicle is designed to record up to five seconds of specific vehicle data parameters (see list below) in an event data recorder prior to the moment of airbag deployment, or near-deployment, and up to a quarter second of high-speed deceleration data during and/or after air bag deployment or neardeployment. EDR data are ONLY recorded if an airbag deploys, or nearly deploys, and are otherwise unavailable.
106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the US government and various states. Data of a potentially sensitive nature, such as would identify a particular driver, vehicle, or crash, will be treated confidentially. Confidential data will not be disclosed by DaimlerChrysler to any third party except when: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Cruise control status • Traction/stability control status • Tire pressure monitoring system status CHILD RESTRAINT Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.
108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and 9convertible9 child seats. Both types of child restraints are held in the vehicle by the lap/ shoulder belt or the LATCH child restraint anchorage system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s cushion while the child’s back is against the seat back; they should use a Belt Positioning Booster Seat. The child and booster seat are held in the vehicle by the lap/ shoulder belt.
110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it, before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. all removed from the retractor. Allow the belt to return into the retractor, as the belt retracts, you will hear a clicking sound.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the latch plate around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. using the vehicle seat belt. Both rear seating positions have exclusive lower anchorages located at the rear of the seat cushion.
112 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child restraints systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the top tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 113 rearward-facing infant restraints will also be equipped with a tether strap with a hook and means for adjusting the tension in the strap. 2 In general, you will first loosen the adjusters on the lower and tether straps so that you can more easily attach the hook or connector to the lower and tether anchorages.
114 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a child restraint top tether strap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your vehicle. Drive moderately during the first 300 mi (500 km). After the initial 60 mi (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration, within the limits of local traffic laws, contributes to a good break-in. Wide-open throttle acceleration in low gear can be detrimental and should be avoided.
116 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. WARNING! If you are required to drive with the deck lid/liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect tread and sidewall for cuts or cracks. Check wheel nuts for tightness, and tires (including spare) for proper pressure. Lights Have someone observe the operation of exterior lights while you work the controls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 m Convertible Top Operation . . . . . . . . . . . . . . . . 123 ▫ Outside Mirror—Driver’s Side . . . . . . . . . . . . 136 ▫ To Lower The Top . . . . . . . . . . . . . . . . . . . . . 123 ▫ Outside Mirror—Passenger’s Side . . . . . . . . . . 136 ▫ To Raise The Top . . . . . . . . . . . . . . . . . . . . . 126 ▫ Electric Remote-Control Mirrors — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ UConnect™ System Features . . . . . . . . . . . . . 149 ▫ Folding Rear Seat (Sedan) . . . . . . . . . . . . . . . 171 ▫ Advanced Phone Connectivity . . . . . . . . . . . . 154 ▫ Folding Rear Seat (Convertible) . . . . . . . . . . . 173 ▫ Things You Should Know About Your UConnect™ System . . . . . . . . . . . . . . . . . . . . 155 ▫ Tumbling Rear Seat (Sedan) . . . . . . . . . . . . . . 175 ▫ General Information . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . 187 ▫ To Set At A Desired Speed . . . . . . . . . . . . . . . 195 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . 188 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . . 195 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . 188 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . . 195 ▫ Highbeam/Lowbeam Select Switch . . . . . . . . .
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . . . 203 m Rear Shelf Panel— If Equipped . . . . . . . . . . . . . 210 ▫ General Information . . . . . . . . . . . . . . . . . . . 203 ▫ Position 1 (Top) . . . . . . . . . . . . . . . . . . . . . . 211 m Power Sunroof (Sedan Only) — If Equipped . . . . 204 ▫ Position 2 (Middle) . . . . . . . . . . . . . . . . . . . . 212 ▫ Express Open Feature . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONVERTIBLE TOP OPERATION WARNING! The convertible top does not provide the structural protection that a reinforced metal roof does, and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision. Therefore it is important that all occupants wear their seat belts at all times when riding in a convertible.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! To fully insure that no damage occurs, be sure that the vehicle is at a complete stop with the gear selector in the Park position (automatic transaxle) or in the Neutral position (manual transaxle) before lowering or raising the top. To avoid damage to either the top or the rear window, check the top storage area at the rear of the vehicle interior to be sure that it is clear of debris or other items.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 the Power Top Switch lightly in the first detent position will lower the windows slightly and the convertible top to the full down position. Pressing and holding the switch in the second detent position will lower all four windows completely and the top to the full down position. Releasing Convertible Top Latches 3.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Continue pressing the Power Top Switch until the convertible top is lowered completely. 5. Install the Convertible Top Boot Cover, if equipped. Refer to Convertible Top Boot Cover Installation–If Equipped, in this section. CAUTION! Damage to the convertible top boot cover could result if the latch handle is not completely closed when the top is lowered. The convertible top boot cover cannot be installed while the latch handle is open.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 1. Remove the convertible top boot cover, if equipped. Refer to Convertible Top Boot Cover Removal and Storage, in this section. 2. Turn the ignition to the ON position. 3 3. Press the Power Top Switch to raise the top. Before the top reaches the windshield, open the latch handle and turn the handle clockwise to open the latches. Press the switch again to continue raising the top until the two pins seat themselves in the windshield header.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Car top carriers, ski racks, etc., should not be attached to the convertible top mechanism as they will damage the top. Do not place objects on the convertible top, in the top well or on the sport bar. Damage to the convertible top may occur. Convertible Top Boot Cover Installation–If Equipped 1. With the top down and the convertible top latch handle in the stowed position, lay the unfolded boot cover across the convertible top.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 2. Install the rear edge of the boot, first tucking the rear edge of the boot under the rear and both sides of the rails.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull the right and left boot arms forward and engage both boot arm snaps. Make sure both snaps are fully engaged.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Engage the boot center section retainer using the tabs provided. 131 5. Tuck the rear flap of the boot in behind the Upper Moulding.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Convertible Top Boot Cover Removal and Storage 1. Unsnap the snaps and remove the top cover boot. 2. Lay the boot cover flat with the center section retainer facing the rear of the car.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 3. First fold the left side of the boot cover to the middle of the boot cover. 3 Folding Boot Cover Right Side Folding Boot Cover Left Side 4. Second fold the right side of the boot cover to the middle, fitting it inside the left side of the boot cover and store it in the trunk or a dry secure area. CAUTION! Do not lay heavy objects on top of the boot or lay the boot on top of sharp/pointy objects. Damage could occur to the boot.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONVERTIBLE TOP MANUAL OVERRIDE If your vehicle is experiencing electrical failure (low battery, etc.) and it is necessary to raise the convertible top, perform the following steps: 1. Locate the convertible top motor bypass screw, which is found in the trunk under the convertible top storage area. 2. Turn the screw counterclockwise until the screw stops. This will relieve the hydraulic pressure and allow the convertible top to be raised manually.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 6. Raise the handle into the stowed position. 7. Close the convertible top motor bypass screw by turning the screw clockwise until it stops. Tighten the screw securely. NOTE: Failure to tighten the bypass screw securely can cause convertible top operating concerns. MIRRORS Engaging Convertible Top Latches Inside Day/Night Mirror — If Equipped Adjust the mirror to center on the view through the rear window.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield). Outside Mirror—Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electric Remote-Control Mirrors — If Equipped The power mirror switch is located to the left of the steering column on the instrument panel. To adjust the view in the outside mirrors, turn the rotary knob to the L (Left), O (Center) or R (Right) position. After selecting the mirror, move the knob in the same direction you want the mirror to move. Use the O (Center) position to guard against accidentally moving a mirror position.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on the sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights turn on automatically. Closing the mirror cover turns off the lights. NOTE: The driver vanity mirror will become inoperable when the vehicle alarm is enabled. NOTE: The passenger vanity mirror will become inoperable if left on for more than 10 minutes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The UConnect™ system use requires a cellular phone equipped with the Bluetooth 9Hands-Free Profile,9 version 0.96 or higher. See www.chrysler.com/uconnect for supported phones. UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s microphone for private conversation. The UConnect™ phonebook enables you to store up to 32 names and four numbers per name.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ system can be used with any HandsFree Profile certified Bluetooth™ cellular phone. See www.chrysler.com/uconnect for supported phones. If your cellular phone supports a different profile (e.g., Headset Profile), you may not be able to use any UConnect™ features. Refer to your cellular service provider or the phone manufacturer for details.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE example, you can use the combined form voice command 9Phonebook New Entry,9 or you can break the combined form command into two voice commands: 9Phonebook9 and 9New Entry.9 Please remember, the UConnect™ system works best when you talk in a normal conversational tone, as if speaking to some one sitting eight feet away from you. Voice Command Tree Refer to “Voice Tree” at the end of this section.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the 9Ready9 prompt and the following beep, say 9Setup Phone Pairing9 and follow the audible prompts. • When prompted, after the voice on beep, say 9Pair a Phone9 and follow the audible prompts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Call/Dial by Saying a Number Call/Dial by Saying a Name • Press the ’Phone’ button to begin. • Press the “Phone” button to begin. • After the 9Ready9 prompt and the following beep, say 9Dial.9 • After the 9Ready9 prompt and the following beep, say “Dial” or Call.9 • System will prompt you to say the number you want call. • System will prompt you to say the name of the person you want call. • For example, you can say “234-567-8901.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Add Names to Your UConnect™ Phonebook NOTE: Adding names to phonebook is recommended when vehicle is not in motion. • Press the “Phone” button to begin. • After the 9Ready9 prompt and the following beep, say 9Phonebook New Entry.9 • When prompted, say the name of the new entry. Use of long names helps the voice recognition and is recommended. For example, say 9Robert Smith9 or 9Robert9 instead of 9Bob.9 • When prompted, enter the number designation (e.g.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, mobile, or pager) that you wish to edit. • When prompted, recite the new phone number for the phonebook entry that you are editing. After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After you enter the name, the UConnect™ system will ask you which designation you wish to delete, home, work, mobile, or pager. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted. After confirmation, the phonebook entries will be deleted. Note that only the phonebook in the current language is deleted. Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone Call Features The following features can be accessed through the UConnect™ system if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the UConnect™ system. Check with your cellular service provider for the features that you have.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE second call is in progress. To go back to the first call, refer to 9Toggling Between Calls.9 To combine two calls, refer to 9Conference Call.9 Place/Retrieve a Call from Hold To put a call on hold, press the 8Phone’ button until you hear a single beep. This indicates that the call is on hold. To bring the call back from hold, press and hold the 8Phone’ button until you hear a single beep.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE hold may not become active automatically. This is cell phone dependent. To bring the call back from hold, press and hold the ‘Phone’ button until you hear a single beep. Redial • Press the ’Phone’ button to begin. • After the 9Ready9 prompt and the following beep, say 9Redial.9 • The UConnect™ system will call the last number that was dialed on your cellular phone. Note: this may not be the last number dialed from the UConnect™ system.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the 9Ready9 prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped). • Continue to follow the system prompts to complete language selection. After selecting one of the languages, all prompts and voice commands will be in that language. NOTE: After every UConnect™ language change operation, only the language specific 32-name phonebook is usable.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your phone must be turned on and paired to the UConnect™ system to allow use of this vehicle feature in emergency situations when the cell phone has network coverage and stays paired to the UConnect™ system. Towing Assistance If you need towing assistance, • Press the ’Phone’ button to begin. • After the 9Ready9 prompt and the following beep, say 9Towing Assistance.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When calling a number with your UConnect™ system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’Voice Recognition’ button and say the sequence you wish to enter followed by the word 9Send.9 For example, if required to enter your pin number followed with a pound 3 7 4 6 #, you can press the ’Voice Recognition’ button and say 93 7 4 6 # Send.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth™ cellular phone, the audio will be played through your vehicle’s audio system.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Information Service When using AT&T Wireless Service, dialing to phone number 9#121,9 you can access voice activated automated system to receive news, weather, stocks, traffic, etc. related information. If you would like to connect or disconnect the Bluetooth™ connection between a UConnect™ paired cellular phone and the UConnect™ system, then follow the instruction described in your cellular phone user’s manual.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Select another Cellular Phone This feature allows you to select and start using another phone with the UConnect™ system. The phone must have been previously paired to the UConnect™ system that you want to use it with. Delete UConnect™ Paired Cellular Phones • Press the ’Phone’ button to begin. • At the next prompt, say 9Delete9 and follow the prompts. • After the 9Ready9 prompt and the following beep, say 9Setup Select Phone9 and follow the prompts.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE training mode, follow one of the two procedures: From outside the UConnect mode (e.g. from radio mode), • Press and hold the ‘Voice Recognition’ button for 5 seconds until the session begins, or • Press the ‘Voice Recognition’ button and say 9Setup, Voice Training9 command. Repeat the words and phrases when prompted by the UConnect System.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 • In a convertible vehicle, the system performance may be compromised with roof top down. • You can say 9O9 (letter 9O9) for 909 (zero). 98009 must be spoken 9eight-zero-zero.9 • Even though the system is designed for users speaking in North American English, French, and Spanish accents, the system may not always work for some.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In a convertible vehicle, the system performance may be compromised with roof top down. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the UConnect™ system. • Echo at far end can sometime be reduced by lowering the in-vehicle audio volume. Bluetooth Communication Link Occasionally, Cellular phones have been found to lose connection to the UConnect™ system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 3
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 3
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary Zero One Two Three Four Five Six Seven Eight Nine Star (*) Plus (+) Pound (#) Add Location All North American English Alternate(s) Call Cancel Confirmation Prompts Continue Delete Dial Edit Emergency English Erase All Espanol Francais Help Home Language List names List phones
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mobile Mute Mute off New entry No Pager Pair a phone Phone pairing Phonebook Previous Record again Redial Return to main menu Select phone Send Set up 163 Towing assistance Transfer call Try again Voice training Work Yes Pairing Phone book General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. Return.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS FRONT SEAT ADJUSTMENT The adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position. Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched. WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SEAT ADJUSTER — IF EQUIPPED WARNING! Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. 165 Six-Way Power Seat with Manual Recliner The seat switch is on the outboard side of the seat near the floor.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This seat also has a manual recline lever located just to the rear of the power seat switch. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position. MANUAL LUMBAR — IF EQUIPPED The Lumbar adjustment is located on the inboard side of the driver’s seat. To increase support, rotate the handle down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE FOLDING FRONT PASSENGER SEAT — IF EQUIPPED The passenger front seat may be folded fully forward to provide additional cargo space. To fold the seat forward pull up on the recliner lever located on the outboard side of the seat. Folding Seat Control Lever 167 DRIVER’S SEAT BACK TILT — IF EQUIPPED How to operate the driver’s seat: 1. Push the lever down until seat back releases. 2. Push the seat back forward. 3.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The driver’s front seat has a full recliner memory, which will allow the seat back to return to its original position. PASSENGER SEAT BACK TILT (EASY ENTRY SYSTEM) — CONVERTIBLE How to operate the passenger front seat: 1. Push the lever down until seat back releases. 2. Push seat back forward until it slides toward the dashboard.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. To return seat to a sitting position, rotate seat back upright until it locks. 4. Push seat rearward until the track locks. NOTE: The passenger front seat has a full recliner memory, which will allow the seat back to returned to its original position. NOTE: The passenger front seat has a track memory, which returns the seat to just past the half way point of the track regardless of original position.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. To avoid heated seat surfaces coming in contact and potential seat overheating, ALWAYS ensure that the seat heater is in the OFF position (amber lights are on for HIGH or LOW and no amber lights for the OFF position) before placing any of the seats into a folded flat position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the HIGH setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the normal HIGH temperature level. If the HIGH setting is selected, the system will automatically switch to LOW after 30 minutes of continuous operation. At that time, the number of illuminated LEDs changes from two to one, indicating the change. The LOW setting will turn off automatically after 30 minutes.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts • Be sure that everyone in your vehicle is in a seat and using a seat belt properly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE FOLDING REAR SEAT (CONVERTIBLE) To provide additional storage area, each rear seatback can be folded forward. The seat back release knobs are located in the trunk area. Pull the left side seatback release knob to fold down the left side seatback. Pull the right side seatback release knob to fold down the right side seatback.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure that everyone in your vehicle is in a seat and using a seat belt properly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TUMBLING REAR SEAT (SEDAN) To provide additional storage in the cargo area, each rear seat can be tumbled forward. 175 • Push and hold the button on the seatback and fold down the rear seatback. CAUTION! 3 It is important that the front seats be pulled forward to the midpoint of the seat track to avoid contact between the rear seat and the front seatback.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Pull the release handle located on the outboard side of the seat. Lift up the seat and tumble the seat forward. Tumbling Seat Strap Tumbling Seat Release Strap • Attach the elastic strap, located at the base of the seat cushion, onto the hook bar on the center trim panel to hold the seat in place. To return the rear seat to it’s upright latched position, rotate the seat cushion rearward to latch the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TUMBLING REAR SEAT (CONVERTIBLE) To provide additional storage area, each rear seat can be tumbled forward. CAUTION! 177 To tumble the seat forward use the following procedure: 1. The seat back release knobs are located in the trunk area. Pull the left side seatback release knob to fold down the left side seatback. Pull the right side seatback release knob to fold down the right side seatback.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. From inside the vehicle, fold the rear seat back down flat. Tumbling Rear Seat Folding Rear Seat Back 3. Pull the release strap located at the bottom of the folded seat back and tumble the seat forward. 4. Attach the cinching tether strap, located at the side of the seat cushion, onto the hook bar on the center trim panel and tighten by pulling the cinching strap until the seat is secure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 3 Cinching Tether Strap To return the tumbling rear seat to the latched (normal) position use the following procedure: 1. Loosen the strap by pushing rearward on the cinching tether strap buckle. Releasing Cinching Tether Strap 2. Disconnect the cinching tether strap. NOTE: The strap should be reinstalled in the side pocket on the seat cushion before returning the seat to the latched (normal) position.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Prior to rotating the seat cushions rearward, be sure that the rear seat belt buckles are secured with the straps, so that the buckles are accessible. NOTE: Prior to lifting either seatback to the upright position, be sure that the seat belt is brought forward to avoid trapping it behind the seatback. 3. Rotate the seat cushion rearward to latch the seat. Then lift the seatback to its upright latched position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR SEAT REMOVAL (SEDAN) The rear seats can be removed to provide more cargo space. • Pull the release lever located on the outboard side of the seat. Lift up the seat and tumble the seat forward. • Push and hold the button on the seatback and fold down the rear seatback.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Lift up the release levers to disengage the seat from the floor attachments. NOTE: Small rollers on the bottom of the folded seat and a handle at the top allow the seat to be easily moved when removed from the vehicle. To reinstall the rear seat, insert the seat into the floor attachments. Lower the release levers of the seat to latch the front floor attachments and rotate the seat rearward to latch the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the primary hood release lever located under the left side of the instrument panel. 183 Then move the secondary hood latch (safety latch) located under the front edge of the hood, slightly to the right of center, and raise the hood.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Use the hood prop rod clipped to the driver’s side of the engine compartment to secure the hood in the open position. Place the hood prop at the location stamped into the inner hood surface. To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 20 cm (8 inches) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 NOTE: The lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. They will not turn off automatically. Map/Reading Lights (Convertible) When the ignition switch is in the ON position, these lights, located under the rearview mirror can be turned on by switches located at the base of the rearview mirror.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multi-Function Control Lever The Multi-Function Control Lever controls the operation of the headlights, parking lights, turn signals, headlight beam selection, instrument panel light dimming, interior lights, the passing lights, and fog lights. The lever is located on the left side of the steering column. Headlights, Parking Lights, Instrument Panel Lights Turn the end of the Multi-Function Control Lever to the first detent for parking light operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To change the brightness of the instrument panel lights, rotate the center portion of the Multi-Function Control Lever up or down. 187 Daytime Running Lights (DRL) — If Equipped The high beam lights will come on as Daytime Running Lights (DRL) at DRL intensity (lower), whenever the ignition is on, the engine is running, the headlight switch is off, the parking brake is off, the turn signal is off, and the gear shift is in any position except park.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fog Lights — If Equipped NOTE: The fog lights will only operate with the headlights on low beam. Selecting high beam headlights will turn off the fog lights. Turn Signals Fog Lamp Control The front fog light switch is on the Multi-Function Control Lever. To activate the front fog lights, turn on the parking lights or the low beam headlights and pull out the end of the control lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Move the Multi-Function Control Lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down without moving beyond the detent. 189 Highbeam/Lowbeam Select Switch 3 If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Passing Light You can signal another vehicle with your headlights by lightly pulling the Multi-Function Control Lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released. NOTE: If the Multi-Function Control Lever is held in the flash to pass position for more than 15 seconds, the high beams will shut off. If this occurs, wait 30 seconds for the next flash to pass operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Washers To use the washer, pull the control lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate in low speed for two wipe cycles after the lever is released, and then resume the intermittent interval previously selected. 191 Mist Feature 3 If the lever is pulled while in the OFF position, the wipers will operate for two wipe cycles, then turn OFF.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! In cold weather, always turn off the wiper switch and allow the wipers to return to the park position before turning off the engine. If the wiper switch is left on and the wipers freeze to the windshield, damage to the wiper motor may occur when the vehicle is restarted.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 NOTE: If the front wiper is operating when the ignition is turned off, the wiper will automatically return to the 9Park9 position. When the vehicle is restarted, the wipers will resume operation. 3 TILT STEERING COLUMN To tilt the column, push down on the lever below the multifunction control lever and move the steering wheel up or down, as desired. Pull the lever back up to lock the column firmly in place.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it. To Set At A Desired Speed: When the vehicle has reached the desired speed, press down on the lever and release. Release the accelerator and the vehicle will operate at the selected speed.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tapping RESUME ACCEL once will result in a 2 mph (3 km/h) speed increase. Each time the lever is tapped, speed increases so that tapping the lever three times will increase speed by 6 mph (10 km/h), etc. To decrease speed while speed control is ON, push down and hold SET DECEL. Release the lever when the desired speed is reached, and the new speed will be set. Tapping the SET DECELbutton once will result in a 1 mph (2 km/h) speed decrease.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 Vehicles equipped with four speed automatic transaxles may experience a downshift to third gear while climbing uphill or descending downhill. This downshift to third gear is necessary to maintain vehicle set speed. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your vehicle should be parked outside of the garage when programming. 1. Turn the ignition switch to the ON/RUN position. 2. Hold the battery side of the hand-held transmitter away from the HomeLinkt button you wish to program. Place the hand-held transmitter 1–3 in (3-8 cm) away from the HomeLinkt button you wish to program while keeping the indicator light in view. 3.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the indicator light blinks rapidly for two seconds, and then turns to a constant light, continue with programming for a Rolling Code. 5. PROGRAMMING A ROLLING CODE SYSTEM At the garage door opener motor (in the garage), locate the “Learn” or “Training” button. This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7. Return to the vehicle and press the programmed HomeLinkt button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for two seconds) to complete the training.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE has successfully accepted the frequency signal. The indicator light will flash slowly and then rapidly when fully trained. If you unplugged the device for training, plug it back in at this time. Then proceed with Step 4 under “Programming HomeLinkt” earlier in this section. USING HOMELINKT To operate, simply press and release the programmed HomeLinkt button. Activation will now occur for the trained device (i.e.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLinkt Universal Transceiver is disabled when the Vehicle Security Alarm is active. TROUBLESHOOTING TIPS If you are having trouble programming HomeLinkt, here are some of the most common solutions: • Replace the battery in the original transmitter. • Press the “Learn” button on the Garage Door Opener to complete the training for a Rolling Code.
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF (SEDAN ONLY) — IF EQUIPPED The power sunroof switch is located in the reading lamp. Turn the Ignition Key to the ACC or ON position, press and hold the switch rearward to fully open the sunroof. The sunroof can be stopped at any position between closed and full open. Momentarily pressing the switch rearward will activate the Express Open Feature, causing the sunroof to open automatically.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To close the sunroof, hold the switch in the forward position. Again, any release of the switch will stop the movement and the sunroof will remain in a partial open condition until the switch is pushed forward again. The sunshade can be opened manually. It will also open as the sunroof opens. The sunshade cannot be closed if the sunroof is open. WARNING! Never leave children in a vehicle, with the keys in the ignition switch.
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE There is one optional power outlet located in the right rear cargo area. 207 The Rear Power Outlet is powered directly by the battery. As an option, fuse #11 in the Integrated Power Module (IPM), may be repositioned to allow power to come from the ignition switch only when in the ON or ACC positions. NOTE: The Rear Power Outlet will not accept a cigar lighter unit as it is intended only for accessory items.
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.), will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged into the 12 volt power outlet, draw power from the vehicle’s battery, even when not in use; i.e. cellular phones, etc. Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. STORAGE Center Console/Armrest Storage Bin 3 • Accessories that draw higher power such as coolers, vacuum cleaners, lights, etc.
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The center console provides a sliding armrest with two unique storage compartments under the lid. Push the upper button on the front of the armrest to raise the upper cover. Inside is an area to store a cell phone and other miscellaneous items. Push the lower button on the front of the armrest, and raise the armrest for access to the lower storage bin. The lower storage area can be used for storing up to six CD’s and other miscellaneous items.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 WARNING! • To avoid tipping, lock the shelf securely in all positions. • Do not drive this vehicle with the liftgate open, or use the shelf as a seat. 3 • Failure to follow these warnings could result in serious or fatal injury. Position 1 (Top) Insert the front outboard corners of the shelf panel into the top guides and slide forward. Press down on the back of the shelf panel to lock it into place.
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Position 2 (Middle) Insert the front outboard corners of the shelf panel into the middle guides and slide forward. Press down on the back of the shelf panel to lock it into place. WARNING! Do not load objects over 100 lbs (45 kg) in position 2 (middle). Failure to follow this warning could cause the shelf to collapse resulting in personal injury. Position 3 (Floor) Insert the front outboard corners of the shelf panel into the bottom guides and slide forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 WARNING! When in the vertical position, the rear shelf panel should not be used as a barrier for large objects in the cargo area when the seatbacks folded down. In an accident objects could strike the seatbacks or occupants causing serious or fatal injury. Rear Shelf Panel Position 4 Position 5 (table) With the liftgate open the rear shelf panel can be moved rearward to act as a serving counter. 1.
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Twist the knob on the underside of the panel and lower the shelf leg. Rear Shelf Panel Position 5 Rear Shelf Leg Release Knob 3. Install the shelf leg into the liftgate latch area as labeled on the rear scuff plate. WARNING! Do not load objects over 100 lbs (45 kg) in position 5 (table). Failure to follow this warning could cause the shelf to collapse resulting in personal injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. To adjust the crossbars with bottom-style releases (if equipped), depress the button and slide the crossbar to the next locking position.
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately. Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Electric Rear Window Defroster 217 NOTE: The defroster turns off automatically after 10 minutes of operation. Each following activation of the defroster will last for five minutes. CAUTION! Rear Defroster Switch The push-button is located at the center of the instrument panel, below the radio. Press this button to turn on the rear window defroster, and the optional electric remote control heated mirrors.
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE wash pump will continue to operate as long as the button is pressed. Upon release, the wipers will cycle two times before returning to the set position. If the rear wiper is operating when the ignition is turned OFF, the wiper will automatically return to the “Park” position if power accessory delay is active. Power accessory delay can be cancelled by opening the door, if this happens the rear wiper will stop at its current position and will not go to park.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS m Instrument Panel Features . . . . . . . . . . . . . . . . . 222 ▫ Odometer Display . . . . . . . . . . . . . . . . . . . . . 239 m Instrument Cluster—Base . . . . . . . . . . . . . . . . . 223 ▫ Trip Odometer (ODO) . . . . . . . . . . . . . . . . . . 239 m Instrument Cluster—Premium . . . . . . . . . . . . . . 224 m Electronic Vehicle Information Center (EVIC) – If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .
220 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Tire Pressure Monitor (TPM) . . . . . . . . . . . . . 244 ▫ Operating Instructions - CD Mode . . . . . . . . . 255 ▫ Personal Settings (Customer Programmable Features) . . . . . . . . . . . . . . . . . . . . . . . . . . . 244 ▫ Operating Instructions - Auxiliary Mode . . . . . 257 m Setting The Analog Clock . . . . . . . . . . . . . . . . . 250 m Radio General Information . . . . . . . . . . . . . . . . 250 ▫ Radio Broadcast Signals . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Notes On Playing MP3 Files . . . . . . . . . . . . . 268 ▫ Operating Instructions - (CD Mode For MP3 Audio Play) . . . . . . . . . . . . . . . . . . . . . . . . . 270 221 ▫ Using The PTY (Program Type) Button (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . 275 ▫ PTY Button 9Scan9 . . . . . . . . . . . . . . . . . . . . . 275 ▫ Load/Eject Button (CD Mode For MP3 Play) . . 271 ▫ PTY Button 9Seek9 . . . . . . . . . . . . . . . . . . . . .
222 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 - Air Vent 2 - Instrument Cluster 3 - Power Windows 4 - Analog Clock * If Equipped 5 6 7 8 - Radio - Assist Handle - Glove Compartment - Heated Seats* 9 - TRAC Off 10 - Climate Controls 11 - Storage Cubby 12 - Pass Airbag Off 13 14 15 16 - Hazard Lights Rear Window Defroster* Power Convertible Top Side Mirror Control*
UNDERSTANDING YOUR INSTRUMENT PANEL 223 INSTRUMENT CLUSTER—BASE 4
224 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER—PREMIUM
UNDERSTANDING YOUR INSTRUMENT PANEL 225 INSTRUMENT CLUSTER—TURBO 4
226 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Fuel Door Reminder This is a reminder that the Fuel Filler Door is located on the front passenger’s (right) side of the vehicle. 3. Temperature Gauge The temperature gauge shows engine coolant temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL 5. Tachometer The white area of the scale shows the permissible engine revolutions-per-minute (rpm x 1000) for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 6. Transmission Range Indicator This display indicator shows the automatic transmission gear selection. 7.
228 UNDERSTANDING YOUR INSTRUMENT PANEL Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists.
UNDERSTANDING YOUR INSTRUMENT PANEL 8. Odometer/Trip Odometer A vacuum fluorescent display indicates the total distance the vehicle has been driven. Also, the cluster will display, replacing the odometer/trip odometer, vehicle warning messages such as: door/deck/hatch/gate ajar and loose gas cap. Loose gas cap will be displayed from the Odometer/Trip Odometer on all models.
230 UNDERSTANDING YOUR INSTRUMENT PANEL Certain conditions such as a loose or missing gas cap, poor fuel quality, etc. may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations the vehicle will drive normally and will not require towing.
UNDERSTANDING YOUR INSTRUMENT PANEL 14. Electronic Stability Program (ESP) Indicator Light/Traction Control System (TCS) Indicator Light — If Equipped If this indicator light flashes during acceleration, apply as little throttle as possible. While driving, ease up on the accelerator. Adapt your speed and driving to the prevailing road conditions, and do not switch off the ESP, or TCS — if equipped. 15.
232 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! Driving a vehicle with the brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately. Vehicles equipped with Anti-Lock brakes (ABS), are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 will sound 10 times. After the chime turns off, the engine will still be critically hot until the light goes out. light will come on when the ignition key is turned to the ON position and may stay on for as long as four seconds. 18. Low Fuel Light When the fuel level drops to 2 gallons, the fuel symbol will light and a single chime will sound.
234 UNDERSTANDING YOUR INSTRUMENT PANEL 22. Oil Pressure Light Shows low engine oil pressure. The light will come on and remain on when the ignition switch is turned from the OFF to the ON position, and the light will turn off after the engine is started. If the bulb does not come on during starting, have the system checked by an authorized dealer. If the light comes on and remains on while driving, stop the vehicle and shut off the engine. DO NOT OPERATE THE VEHICLE UNTIL THE CAUSE IS CORRECTED.
UNDERSTANDING YOUR INSTRUMENT PANEL 26. Compass Mini-Trip Computer (CMTC) or Electronic Vehicle Information Center (EVIC) Display — If Equipped On vehicles equipped with Electronic Vehicle Information Center (EVIC), when the appropriate conditions exist, this display shows the EVIC messages. Refer to “Electronic Vehicle Information Center” later in this section.
236 UNDERSTANDING YOUR INSTRUMENT PANEL When the appropriate conditions exist, the following messages will display in the window below the fuel and engine temperature gauge: E . . . . . . . . Eight-point compass headings are displayed (N, S, E, W, NE, NW, SE, SW) 14°F. . . . . . . . . . . . Temperature (Fahrenheit or Celsius) AVG . . . . . . . . . Average Fuel Economy (U.S. or Metric) DTE . . . . . . . . . . . . . . . . . . . . . . . Distance to Empty ET . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 237 NOTE: Magnetic materials such as a laptop computer, cell phone, and PDA’s (anything with a battery), should be kept away from the top of the instrument panel. This is where the compass sensor is located. To Set the Variance Start the engine, and leave the transmission gear selector lever in the PARK position. Press and hold (approximately ten seconds) the compass/temperature reset button until the current variance zone number is displayed.
238 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Compass Calibration The compass on your vehicle is self-calibrating, eliminating the need to manually calibrate the compass. When the vehicle is new, the compass may appear erratic and the CAL indicator message will flash in the EVIC until the calibration is complete. A good calibration requires a level surface and an environment free from large metallic objects such as buildings, bridges, underground cables, railroad tracks, etc.
UNDERSTANDING YOUR INSTRUMENT PANEL 4. To complete the compass calibration, drive the vehicle in one or more complete 360 degree circles under 5 mph (8 km/h) in an area free from power lines, large metallic objects, until the “CAL” indicator turns off. The compass will now function normally. Odometer Display When the appropriate conditions exist, the following odometer messages will display: CRUISE . . . . . . . . . . . . . . . . . . . . . . Cruise Activated gASCAP . . . . . . . . . . . . . . . . . . . . .
240 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) – If Equipped NOTE: The compass on your vehicle is self-calibrating, eliminating the need to manually calibrate the compass. The Electronic Vehicle Information Center (EVIC) features a driver-interactive display. It is located in the lower left part of the cluster below the fuel and engine temperature gauge.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 When the appropriate conditions exist, the Electronic Vehicle Information Center (EVIC) displays the following messages. • Personal Settings Not Available – Vehicle Not in (automatic transmissions) or vehicle is in motion (manual transmissions).
242 UNDERSTANDING YOUR INSTRUMENT PANEL • Distance To Empty (DTE) EVIC Functions • Elapsed Time • Tire Pressure Monitor (TPM) • Personal Settings EVIC Button Press the EVIC button until one of the following functions are displayed on the EVIC: • Compass/Temperature/Audio • Average Fuel Economy To Reset The Display Pressing and holding the EVIC button once will clear the resettable function currently being displayed. Reset will only occur if a resettable function is currently being displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL Compass/Temperature/Audio Press and release the EVIC button to display one of eight compass headings to indicate the direction the vehicle is facing, the outside temperature and the current radio station. For additional information regarding the compass, refer to Personal Settings (Customer Programmable Features) in this section. Average Fuel Economy Shows the average fuel economy since the last reset.
244 UNDERSTANDING YOUR INSTRUMENT PANEL Elapsed Time Shows the total elapsed time of travel since the last reset when the ignition switch is in the ACC position. Elapsed time will increment when the ignition switch is in the ON or START position. Tire Pressure Monitor (TPM) Refer to Section 5, “Tire Pressure Monitoring System (TPMS) for system operation.
UNDERSTANDING YOUR INSTRUMENT PANEL Auto Unlock On Exit When ON is selected all the vehicle’s doors will unlock when the driver’s door is opened if the vehicle is stopped (manual transmissions) or the vehicle is stopped and the transmission is in PARK or NEUTRAL position (automatic transmissions). Press and hold the EVIC button when in this display until ON or OFF appears to make your selection.
246 UNDERSTANDING YOUR INSTRUMENT PANEL when exiting the vehicle. Press and hold the EVIC button when in this display until 0, 30, 60, or 90 appears to make your selection. Headlamps On With Wipers (Available with Auto Headlights Only) When ON is selected and the headlight switch is in the AUTO position, the headlights will turn on approximately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on by this feature.
UNDERSTANDING YOUR INSTRUMENT PANEL Display English or Metric The EVIC, odometer, and navigation system units can be changed between English and Metric. Press and hold the EVIC button when in this display until “US” or “METRIC” appears to make your selection. Automatic Compass Calibration The compass on your vehicle is self-calibrating, eliminating the need to manually calibrate the compass.
248 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Press and release the EVIC button several times until the EVIC displays the Personal Settings (Customer Programmable Features) menu. 3. Press and release the EVIC button several times until “Calibrate Compass (Yes)” is displayed. A long (longer than two seconds) EVIC button Press will place the Compass in calibration mode. 4.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 1. Turn the ignition switch to the ON position. Leave the gear selector lever in PARK. 2. Press and release the EVIC button several times until you have displayed the Personal Settings (Customer Programmable Features) menu. 3. Press and release the EVIC button until “Compass Variance” and the current Variance Value displays in the EVIC. 4.
250 UNDERSTANDING YOUR INSTRUMENT PANEL SETTING THE ANALOG CLOCK To set the analog clock at the top center of the instrument panel, press and hold the button until the setting is correct. The clock will adjust slowly at first and then quicker the longer the button is held. Setting The Analog Clock RADIO GENERAL INFORMATION Radio Broadcast Signals The radio will provide excellent reception under most operating conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal. SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL SATELLITE RADIO AND HANDS FREE PHONE CAPABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate.
252 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: In Hands-Free Phone (if equipped) mode, the MUTE button mutes the microphone. SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station in either, AM, FM, or Satellite (if equipped) frequencies, pausing for five seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time.
254 UNDERSTANDING YOUR INSTRUMENT PANEL TUNE Control (Radio Mode) Turn the rotary TUNE control clockwise to increase or counterclockwise to decrease the frequency. Press the rotary TUNE control a fourth time and BAL will display. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers. AM/FM Button (Radio Mode) Press the button to select AM or FM modes. Press the rotary TUNE control a fifth time and FADE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM, 12 FM, and 12 Satellite (if equipped) stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice.
256 UNDERSTANDING YOUR INSTRUMENT PANEL • If you insert a disc with the ignition ON and the radio OFF, the CD will automatically be pulled into the CD player. SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. • This radio does not play discs with MP3 tracks. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal.
UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the FF button to fast forward through the tracks. Release the FF button to stop the fast forward feature. If the RW button is pressed, the current track will reverse to the beginning of the track and begin playing. RND/SET Button (Random Play Button) (CD Mode) Press this button while the CD is playing to activate Random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace.
258 UNDERSTANDING YOUR INSTRUMENT PANEL MUTE Button (Auxiliary Mode) Press the MUTE button to cancel the sound from the speakers. 9MUTE9 will display. Press the MUTE button a second time and the sound from the speakers will return. Rotating the volume control or turning off the ignition will also return the sound from the speakers. SCAN Button (Auxiliary Mode) No function. EJECT Button (Auxiliary Mode) No function. PSCAN Button (Auxiliary Mode) No function.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS-FREE PHONE, AND VIDEO ENTERTAINMENT SYSTEMS (VES™) CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate. 4 RAQ Radio Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
260 UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it. When the audio system is turned on, the sound will be set at the same volume level as last played.
UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station, in either AM, FM or Satellite (if equipped) frequencies, pausing for five seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time. MSG or INFO Button (Radio Mode) Press the MSG or INFO button for an RBDS station (one with call letters displayed).
262 UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button (Radio Mode) Press the button to select AM or FM Modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control, and BASS will display. Turn the TUNE control to the right or left to increase or decrease the Bass tones. Press the rotary TUNE control a second time and MID will display. Turn the TUNE control to the right or left to increase or decrease the Mid Range tones. Press the rotary TUNE control a third time and TREBLE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the PTY button to select the following format types: Program Type No program type or undefined Adult Hits Alert Alert Classical Classic Rock College Country Emergency Test Foreign Language Information Jazz News Nostalgia 16 Digit-Character Display None Adult_Hits Alert Alert Classical Classic_Rock College Country Emergency Test Foreign_Language Information Jazz News Nostalgia Program Type Oldies Personality Public Rhythm and Blues Religious Music Religious Talk
264 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - (CD Mode for CD Audio Play) NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: This Radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable compact discs (CD-RW) compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks. Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up.
266 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button (CD Mode for CD Audio Play) Press the right side of the SEEK button for the next selection on the CD. Press the left side of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. MUTE Button (CD Mode for CD Audio Play) Press the MUTE button to cancel the sound from the speakers. 9MUTE9 will be displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL Radio display will show 9EJECTING DISC9 when the disc is being ejected and prompt the user to remove the disc. Press and hold the LOAD/ EJT button for five seconds and all CDs will be ejected from the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not removed, the radio will continue to play the non-removed CD.
268 UNDERSTANDING YOUR INSTRUMENT PANEL RND/PTY Button (Random Play Button) (CD Mode for CD Audio Play) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track. Press the RND button a second time to stop Random play. Buttons 1 - 6 (CD Mode for CD Audio Play) Selects disc positions 1 - 6 for Play/Load/Eject.
UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator 9.9 and a 3-character extension) • Level 2: 31 (including a separator 9.9 and a 3-character extension) Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files). Discs created with an option such as 9keep disc open after writing9 are most likely multisession discs.
270 UNDERSTANDING YOUR INSTRUMENT PANEL ID3 Tag information for artist, song title and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported. Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL LOAD/EJECT Button (CD Mode for MP3 Play) LOAD/EJECT - Load Press the LOAD/ EJECT button and the pushbutton with the corresponding number where the CD is being loaded. The radio will display PLEASE WAIT and prompt when to INSERT DISC. After the radio displays 9LOAD DISC9 insert the CD into the player. Radio display will show 9LOADING DISC9 when the disc is loading.
272 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the MSG or INFO button while in the message display priority mode or elapsed time display priority mode will display the song title for each file. Turn the TUNE control to display available folders or move through available folders. Press the TUNE control to select a folder. RW/FF (CD Mode for MP3 Play) Press the FF side of the button to move forward through the MP3 selection.
UNDERSTANDING YOUR INSTRUMENT PANEL SATELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius™ Satellite Radio. This service offers over 130 channels of music, sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios.
274 UNDERSTANDING YOUR INSTRUMENT PANEL ESN/SID Access With RAQ Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and TIME buttons simultaneously for 3 seconds. All twelve ESN/SID numbers will be displayed. The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. ESN/SID Access With Navigation Radios Please refer to your Navigation User’s Manual.
UNDERSTANDING YOUR INSTRUMENT PANEL Press and release the SCAN button (if equipped) to automatically change channels every 7 seconds. The radio will pause on each channel for 7 seconds before moving on to the next channel. The word 9SCAN9 will appear in the display between each channel change. Press the SCAN button a second time to stop the search. NOTE: Channels that may contain objectionable content can be blocked.
276 UNDERSTANDING YOUR INSTRUMENT PANEL PTY Button (SEEK( When the desired program is obtained, press the 9SEEK9 button within five seconds. The channel will change to the next channel that matches the program type selected. Satellite Antenna To ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items should be placed as far forward as possible.
UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD DISC MAINTENANCE To keep the CD/DVD discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper, paper CD labels, or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6.
278 UNDERSTANDING YOUR INSTRUMENT PANEL The air conditioning system of your vehicle contains R-134a, a refrigerant that does not deplete the ozone layer in the upper atmosphere. The controls are as follows: Fan Control Use this control to regulate the amount of air forced through the system in any mode you select. The fan speed increases as you move the control to the right from the OFF position. Mode Control (Air Direction) The mode control allows you to choose from several patterns of air distribution.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. Floor Air is directed through the floor outlets and side window demist outlets with a small amount through the defrost outlet. Mix Air is directed through the floor, defrost and side window demist outlets.
280 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! If the Defroster is not working the windshield and windows may become fogged and your visibility will be greatly diminished. See your authorized dealer as soon as possible. the windshield and windows may become fogged and your visibility will be greatly diminished. Air Outlets The airflow from each of the instrument panel outlets can be adjusted for direction and turned on or off to control air flow.
UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning 281 MAX A/C Rotate this control to engage the Air Conditioning. A lamp will illuminate when the Air Conditioning System is engaged To quickly cool the vehicle interior follow the steps listed below: 4 NOTE: The air conditioning compressor will not engage until the engine has been running for about 10 seconds. 1. Set the Temperature Control to Max Cool. 2. Set the Mode Control to Panel or Be-Level. 3.
282 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • Recirculation Mode will not operate in floor, mix or defrost modes. NOTE: Continuous use of the recirculate mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. • See “Circulation Control” in this section, for proper or extended use of this position. In cold or damp weather, the use of the Recirculate position will cause windows to fog on the inside because of moisture build up inside the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 283 Operating Tips 4 Control Settings Chart
284 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Vehicle side windows tend to fog on the inside in mild rainy or humid weather. To clear the windows, use the A/C, PANEL and blower controls. Direct the panel outlets toward the side windows. Do not use recirculate without A/C for long periods as fogging may occur.
UNDERSTANDING YOUR INSTRUMENT PANEL Side Window Demisters A side window demister outlet is at each end of the instrument panel. These nonadjustable outlets direct air toward the side windows when the system is in either the FLOOR, MIX, or DEFROST mode. The air is directed at the area of the windows through which you view the outside mirrors.
STARTING AND OPERATING CONTENTS m Starting Procedures . . . . . . . . . . . . . . . . . . . . . 291 m Automatic Transaxle — If Equipped . . . . . . . . . 294 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . . 291 ▫ Brake/Transmission Interlock System . . . . . . . 295 ▫ Manual Transaxle . . . . . . . . . . . . . . . . . . . . . 292 ▫ Automatic Transaxle Ignition Interlock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295 ▫ Normal Starting . . . . . . . . . . . . . . . . . .
288 STARTING AND OPERATING m AutoStick — If Equipped . . . . . . . . . . . . . . . . . 299 m Tire Safety Information . . . . . . . . . . . . . . . . . . . 313 ▫ AutoStick Operation . . . . . . . . . . . . . . . . . . . 300 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 313 ▫ AutoStick General Information . . . . . . . . . . . . 300 ▫ Tire Identification Number (TIN) . . . . . . . . . . 316 m Manual Transaxle Operation — If Equipped . . . . 301 ▫ Tire Loading And Tire Pressure . . .
STARTING AND OPERATING 289 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . . 328 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . . 338 ▫ Alignment And Balance . . . . . . . . . . . . . . . . . 329 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . . 338 m Tire Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . 330 ▫ Fuel System Cautions . . . . . . . . . . . . . . . . . . 338 m Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . .
290 STARTING AND OPERATING ▫ Trailer And Tongue Weight . . . . . . . . . . . . . . 348 m Recreational Towing (Behind Motorhome, Etc.) . . 356 ▫ Towing Requirements . . . . . . . . . . . . . . . . . . 349 ▫ Towing This Vehicle Behind Another Vehicle (Flat Towing With All Four Wheels On The Ground) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356 ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle.
292 STARTING AND OPERATING MANUAL TRANSAXLE Before starting the engine fully apply the parking brake, press the clutch pedal to the floor and shift the gear selector lever in NEUTRAL. NOTE: The engine will not start unless the clutch pedal is pressed to the floor. NORMAL STARTING Normal starting of either a cold or a warm engine does not require pumping or depressing the accelerator pedal. Simply turn the ignition switch to the START position and release when the engine starts.
STARTING AND OPERATING IF THE ENGINE FAILS TO START If the engine fails to start after you have followed the “NORMAL STARTING” procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there. Crank the engine for no more than 15 seconds. This should clear any excess fuel in case the engine is flooded. Leave the ignition key in the ON position, release the accelerator pedal and repeat the “NORMAL STARTING” procedure.
294 STARTING AND OPERATING The following chart should be used as a guide in determining the amount of engine idle time required to sufficiently cool down the turbocharger before shut down, depending upon the type of driving and the amount of cargo.
STARTING AND OPERATING WARNING! It is dangerous to shift the gear selector lever out of PARK, or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in REVERSE. You could lose control of the vehicle and hit someone or something. Only shift the gear selector lever into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
296 STARTING AND OPERATING feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service. FOUR-SPEED AUTOMATIC TRANSAXLE The electronically controlled transaxle provides a precise shift schedule. The transaxle electronics are self calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few shift cycles.
STARTING AND OPERATING GEAR RANGES FOR THE FOUR-SPEED AUTOMATIC TRANSAXLE DO NOT race the engine when shifting from PARK or NEUTRAL positions into another gear range. PARK PARK supplements the parking brake by locking the transmission. The engine can be started in this range. Never use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply the parking brake first, and then shift the gear selector lever into the PARK position.
298 STARTING AND OPERATING The following indicators should be used to ensure that you have engaged the transmission gear selector lever into the PARK position: • When shifting the gear selector lever into PARK, depress the button on the gear selector lever knob and firmly move the lever all the way forward until it stops. • Look at the shift indicator window on the console to ensure it is in the PARK position.
STARTING AND OPERATING 299 When frequent transaxle shifting occurs while using the DRIVE/OVERDRIVE range, such as when operating the vehicle under heavy loading conditions (in hilly terrain, traveling into strong head winds, or while towing trailers), use the [3] range. [1] Low This range should be used for maximum engine braking when descending steep grades. In this range, up shifts will occur only to prevent engine over speed while down shifts from [2] to [1] will occur as early as possible.
300 STARTING AND OPERATING AUTOSTICK Operation The AUTOSTICK position is just below the OVERDRIVE position and is identified by the word “AUTOSTICK”. When you place the gear selector lever in the AUTOSTICK position, it can be moved from side to side. Moving the lever to the left (-) triggers a downshift and to the right (+) an upshift. The gear position will be shown in the transmission gear display, located in the instrument cluster.
STARTING AND OPERATING • While in the AUTOSTICK mode, Speed Control will only function in third or fourth gear. Downshifting out of third gear will turn off the speed control. • If the system detects powertrain overheating, the transmission will revert to the automatic shift mode and remain in that mode until the powertrain cools off. • If the system detects a problem it will disable the AUTOSTICK mode and the transmission will return to the automatic mode until the problem is corrected.
302 STARTING AND OPERATING Fully depress the clutch pedal before you shift gears. As you release the clutch pedal, lightly depress the accelerator pedal. Use each gear in numerical order - do not skip a gear. Be sure the gear selector lever is in FIRST gear, (not THIRD), when starting from a standing position. Damage to the clutch can result from starting in THIRD. For most city driving you will find it easier to use only the lower gears.
STARTING AND OPERATING 2.4 LITER TURBO — IF EQUIPPED Five-Speed Shift Pattern With Turbo 303 The neutral position of the gear selector lever is located between THIRD and FOURTH gear. This is the position the gear selector lever will return to automatically when neutral is selected. When shifting into FIFTH gear, be sure to press the gear selector lever all the way to the right to avoid accidentally selecting THIRD gear.
304 STARTING AND OPERATING MANUAL TRANSAXLE — RECOMMENDED SHIFT SPEEDS To use your manual transaxle for optimal fuel economy, it should be upshifted as listed in Table 1. Table 1 - Manual Transaxle Normal Acceleration And Cruise Shift Speeds In mph (km/h) Engine 2.4L Turbo 2.
STARTING AND OPERATING To maintain a safe speed and prolong brake life, shift down to SECOND or FIRST gear when descending a steep grade. When turning a corner, or driving up a steep grade, downshift early so that the engine will not be overburdened. PARKING BRAKE When the parking brake is applied with the ignition on, the BRAKE Light in the instrument cluster will come on. NOTE: This light only shows that the parking brake is on. It does not show the degree of brake application.
306 STARTING AND OPERATING NOTE: The parking brake lever will not release unless the lever is pulled up slightly past its applied position. selector lever out of PARK. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on a uphill grade. You should always apply the parking brake before leaving the vehicle.
STARTING AND OPERATING 307 BRAKE SYSTEM Your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. However, the effort required to brake the vehicle will be much greater than that required with the power system operating.
308 STARTING AND OPERATING ANTI-LOCK BRAKE SYSTEM (ABS) — IF EQUIPPED The ABS provides increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up. WARNING! Pumping of the ABS will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
STARTING AND OPERATING The ABS telltale light monitors the Anti-Lock Brake System. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or comes on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the BRAKE warning light is not on.
310 STARTING AND OPERATING • A slight drop or fall away of the brake pedal at the end of the stop. These are all normal characteristics of ABS. WARNING! The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of Anti-Lock braking capability. Installation of such equipment should be performed by qualified dealership professionals.
STARTING AND OPERATING WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! 311 TRACTION CONTROL SYSTEM — IF EQUIPPED The Traction Control System (TCS) will improve acceleration and steering on slippery surfaces by reducing tire spin. The system reduces wheel slip and maintains traction at the driving (front) wheels by engaging the brake on the wheel that is losing traction.
312 STARTING AND OPERATING The system is always in the “ON” mode unless: • The TCS OFF switch has been used to turn the system off; • There is a Anti-Lock Brake System malfunction; • There is a Traction Control System malfunction; • The system has been automatically deactivated to prevent damage to the brake system due to overheated brake temperatures. NOTE: Extended heavy use of Traction Control may cause the system to deactivate and turn on the TCS indicator lamp located in the instrument cluster.
STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings 313 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter 9P9 is absent from this tire size designation. Example: 215/65R15 96H. • LT (Light Truck)-Metric tire sizing is based on U.S. design standards.
314 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger Car tire size based on U.S. design standards (....blank....( = Passenger Car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%). — Ratio of section height to section width of tire 10.
STARTING AND OPERATING 315 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
316 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure 317 Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side B-Pillar.
318 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard and in the “Vehicle Loading” section of this manual.
STARTING AND OPERATING available cargo and luggage load capacity is 650 lbs (295 kg) {(since 5 x 150 = 750, and 1400 – 750 = 650 lbs (295 kg)}. 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle.
320 STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. 321 1. Safety— WARNING! • Improperly inflated tires are dangerous and can cause accidents. • Under-inflation increases tire flexing and can result in tire failure. TIRES — GENERAL INFORMATION • Over-inflation reduces a tire’s ability to cushion shock.
322 STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under-inflation also increases tire rolling resistance and results in higher fuel consumption. maximum loaded vehicle condition. These pressure conditions will be found in the “Supplemental Tire Pressure Information” section of this manual. 3.
STARTING AND OPERATING check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under-inflated. CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.
324 STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high-speed vehicle operation.
STARTING AND OPERATING Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and reinstalled at the first opportunity. WARNING! Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). Temporary use spare tires have limited tread life.
326 STARTING AND OPERATING original equipped tire on the front or rear axle of your vehicle, but it is not. Installation of this limited-use spare tire affects vehicle handling. Since it is not the same tire, replace (or repair) the original tire and reinstall on the vehicle at the first opportunity. Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck.
STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. 327 These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Many states have laws requiring tire replacement at this point.
328 STARTING AND OPERATING WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death. Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline.
STARTING AND OPERATING 329 WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
330 STARTING AND OPERATING Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. TIRE CHAINS Due to limited clearance, tire chains are not recommended. CAUTION! Damage to the vehicle may result if tire chains are used. SNOW TIRES Some areas of the country require the use of snow tires during Winter.
STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates and tend to develop irregular wear patterns. These effects can be reduced by timely rotation of the tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all-season type tires.
332 STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM (TPMS) — IF EQUIPPED • The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. • The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12°F (7°C). This means that when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on cold inflation tire pressure.
STARTING AND OPERATING driven for up to 10 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. − For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 33 psi (227 kPa). If the ambient temperature is 68° F (20° C) and the measured tire pressure is 28 psi (193 kPa), a temperature drop to 20° F (-7° C) will decrease the tire pressure to approximately 24 psi (165 kPa).
334 STARTING AND OPERATING NOTE: • TPMS is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. • Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings The TPM Light will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. Should this occur, you should stop as soon as possible, check the inflation pressure of each tire on your vehicle, and inflate each tire to the vehicle’s recommended cold placard pressure value.
336 STARTING AND OPERATING 2. If you install the compact spare tire in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition key cycle, a chime will sound and the TPM Telltale Light will turn ON due to the low tire. 3. After driving the vehicle for up to 10 minutes above 15 mph (25 km/h), the TPM Telltale Light will flash on and off for 75 seconds and then remain on solid. 4.
STARTING AND OPERATING FUEL REQUIREMENTS — GASOLINE ENGINES 2.4L AND 2.4L STANDARD TURBO ENGINES 2.4L standard engines are designed to meet all emission regulations and provide excellent fuel economy and performance when using high quality unleaded “regular” gasolines having an octane rating of 87. The use of premium gasoline is not recommended.
338 STARTING AND OPERATING Problems that result from using methanol/gasoline or E85 Ethanol blends are not the responsibility of the manufacturer. While MTBE is an oxygenate made from Methanol, it does not have the negative effects of Methanol. MMT IN GASOLINE MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane number. Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT.
STARTING AND OPERATING • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance, damage the emission control system. • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your dealer for service assistance.
340 STARTING AND OPERATING the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. NOTE: When removing the fuel filler cap, lay the cap tether in the hook, located on the fuel filler cap door reinforcement. • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle.
STARTING AND OPERATING 341 CAUTION! WARNING! • Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • A poorly fitting gas cap could let impurities into the fuel system. • Never add fuel when the engine is running.
342 STARTING AND OPERATING NOTE: • Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is tightened properly. The Malfunction Indicator Light in the instrument cluster may turn on if the gas cap is not secured properly. Make sure that the gas cap is tightened each time the vehicle is refueled. • When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
STARTING AND OPERATING TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer carefully review this information to tow your load as efficiently and safely as possible. To maintain warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.
344 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR. WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident.
STARTING AND OPERATING Weight-Distributing Hitch A weight-distributing system works by applying leverage through spring (load) bars. They are typically used for heavier loads, to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturers’ directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.
346 STARTING AND OPERATING The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the Trailer Towing Weights (Maximum Trailer Weight Ratings) chart for the Max. GTW towable for your given drivetrain. TRAILER HITCH CLASSIFICATION Max. GTW Class (Gross Trailer Wt.
STARTING AND OPERATING 347 TRAILER TOWING WEIGHTS (MAXIMUM TRAILER WEIGHT RATINGS) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission TRAILER TOWING WEIGHTS Max. GTW Frontal Area (Gross Trailer Wt.) Max. Tongue Wt. (See Note 1) 2.4L N/A and 2.4L Turbo/ 20 Sq Ft 1000 lbs (454 kg) 110 lbs (50 kg) Automatic* 2.4L N/A and 2.
348 STARTING AND OPERATING TRAILER AND TONGUE WEIGHT Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents.
STARTING AND OPERATING Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer. • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle.
350 STARTING AND OPERATING WARNING! • Improper towing can lead to an injury accident. • Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident. • Safety chains must always be used between your vehicle and trailer.
STARTING AND OPERATING 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing Requirements — Tires • Do not attempt to tow a trailer while using a compact spare tire. • Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle.
352 STARTING AND OPERATING • Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. WARNING! Do not connect trailer brakes to your vehicle’s hydraulic brake lines.
STARTING AND OPERATING 353 Towing Requirements — Trailer Lights & Wiring Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package may include a four- or sevenpin wiring harness. Use a factory approved trailer harness and connector. NOTE: Do not cut or splice wiring into the vehicles wiring harness.
354 STARTING AND OPERATING TOWING TIPS Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Towing Tips — Automatic Transmission The OVERDRIVE/DRIVE range can be selected when towing. However, if frequent shifting occurs while in this range, the [3] range should be selected.
STARTING AND OPERATING NOTE: Check the automatic transmission fluid level before towing. Towing Tips — Electronic Speed Control (If Equipped) • Don’t use in hilly terrain or with heavy loads. • When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. • Use speed control in flat terrain and with light loads to maximize fuel efficiency.
356 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) NOTE: If the vehicle requires towing make sure all four wheels are off the ground. Towing This Vehicle Behind Another Vehicle (Flat towing with all four wheels on the ground) If your vehicle is equipped with a manual transaxle, it may be towed with all four wheels on the ground, in a forward direction, at any legal highway speed, for any distance, if the transaxle is in NEUTRAL.
WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 358 m Driving On Slippery Surfaces . . . . . . . . . . . . . . 369 m If Your Engine Overheats . . . . . . . . . . . . . . . . . 358 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . . 369 m Jacking And Tire Changing . . . . . . . . . . . . . . . . 360 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .
358 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and the vehicle locked. NOTE: With extended use, the flasher may wear down your battery. Hazard Warning Switch The flasher switch is located on the instrument panel, below the radio. Depress the switch and both cluster indicators and all front and rear directional signals will flash.
WHAT TO DO IN EMERGENCIES the normal range. If the pointer remains on the H (red) mark for more than a minute, turn the engine off immediately and call for service. NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat.
360 WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, refer to Section 7, Maintenance, of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous.
WHAT TO DO IN EMERGENCIES JACK LOCATION The jack and jack-handle are stowed behind the right rear side trim panel in the cargo area. 361 SPARE TIRE STOWAGE The compact spare tire is stowed under the rear of the vehicle by means of a hook/basket mechanism. To remove or stow the compact spare, use the jack handle to rotate the “spare tire drive” nut. The nut is located under the rear scuff plate at the right rear of the cargo area, just inside the liftgate opening.
362 WHAT TO DO IN EMERGENCIES Spare Tire Removal Lift up the cover and fit the jack-handle over the drive nut. Rotate the nut to the left until you can remove the swivel hook from the stowage basket. Swing the basket down to remove the compact spare tire. CAUTION! The hook is designed for use with the jack handle only. Use of an air wrench or other power tools is not recommended and can damage the winch.
WHAT TO DO IN EMERGENCIES JACKING INSTRUCTIONS 363 WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: Jack Warning Label • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in park; a manual transmission in reverse.
364 WHAT TO DO IN EMERGENCIES WARNING! WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Never start or run the engine with the vehicle on a jack. • If working on or near a roadway, be extremely careful of motor traffic. • Do not let anyone sit in the vehicle when it is on a jack.
WHAT TO DO IN EMERGENCIES NOTE: If equipped with a center cap that covers the wheel nuts, pry off the cap using the small end of the lug wrench. To reinstall the cap, make sure it is properly lined up before pushing it on to the wheel. 365 the jack screw to the right until the jack head is properly engaged with the lift area closest to the wheel to be changed. 2. Loosen, but do not remove, the wheel nuts by turning them to the left one turn while the wheel is still on the ground.
366 WHAT TO DO IN EMERGENCIES 4. Raise the vehicle by turning the jack screw to the right, using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. WARNING! To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable.
WHAT TO DO IN EMERGENCIES 8. Remove the wheel blocks and lower the jack until it is free. Stow the lug wrench, and jack in their designated location. Secure all parts using the means provided. WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. 9.
368 WHAT TO DO IN EMERGENCIES WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from another vehicle. This type of start can be dangerous if done improperly, so follow this procedure carefully. 1.
WHAT TO DO IN EMERGENCIES WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush the contaminated area immediately with large quantities of water. A battery generates hydrogen gas which is flammable and explosive. Keep flame or spark away from the vent holes.
370 WHAT TO DO IN EMERGENCIES WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have an accident. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet, mud, loose sand, etc.). 2. Slow down if the road has standing water or puddles. 3. Replace the tires when tread wear indicators first become visible. 4. Keep the tires properly inflated. 5.
WHAT TO DO IN EMERGENCIES WARNING! 371 TOWING A DISABLED VEHICLE With Ignition Key Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed. CAUTION! Racing the engine or spinning the wheels too fast may lead to transaxle overheating and failure.
372 WHAT TO DO IN EMERGENCIES All Transaxles CAUTION! If the vehicle being towed requires steering, the ignition switch must be in the ACC position, not in the LOCK positions. Do not attempt to use sling type equipment when towing. When securing vehicle to flat bed truck, do not attach to front or rear suspension components. Damage to your vehicle may result from improper towing. If it is necessary to use the accessories while being towed (wipers, defrosters, etc.
WHAT TO DO IN EMERGENCIES 373 CONVERTIBLE TOP MANUAL OVERRIDE If your vehicle is experiencing electrical failure (low battery, etc.) and it is necessary to raise the convertible top, perform the following steps: 1. Locate the convertible top motor bypass screw, which is found in the trunk under the convertible top storage area. 2. Turn the screw counterclockwise until the screw stops. This will relieve the hydraulic pressure and allow the convertible top to be raised manually.
374 WHAT TO DO IN EMERGENCIES 3. Using the latch handle raise the top until the two pins seat themselves in the windshield header. 4. Rotate the latch handle clockwise to open the latches. 5. Pull down and rotate the handle counterclockwise to engage the latches. Engaging Convertible Top 6. Raise the handle into the stowed position. 7. Close the convertible top motor bypass screw by turning the screw clockwise until it stops. Tighten the screw securely.
MAINTAINING YOUR VEHICLE CONTENTS m 2.4L Turbo Engine Compartment . . . . . . . . . . . . 378 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 384 m 2.4L Engine Compartment . . . . . . . . . . . . . . . . 379 ▫ Drive Belts — Check Condition And Tension . . 388 m Onboard Diagnostic System — OBD II . . . . . . . . 380 ▫ Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . 388 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . . 381 ▫ Ignition Wiring System . . . . . . . . .
376 MAINTAINING YOUR VEHICLE ▫ Maintenance-Free Battery . . . . . . . . . . . . . . . . 392 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . . 408 ▫ Air Conditioner Maintenance . . . . . . . . . . . . . 393 ▫ Manual Transaxle . . . . . . . . . . . . . . . . . . . . . 410 ▫ Power Steering – Fluid Check . . . . . . . . . . . . 394 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . 411 ▫ Front Suspension Ball Joints . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 377 m Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 425 ▫ Center High Mounted Stop Light . . . . . . . . . . 428 ▫ Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . 425 m Fluids And Capacities . . . . . . . . . . . . . . . . . . . 429 ▫ Front Park/Turn Signal/Side Marker Lights . . 426 m Fluids, Lubricants And Genuine Parts . . . . . . . . 430 ▫ Front Fog Lights — If Equipped . . . . . . . . . . . 426 ▫ Engine . . . . . . . . . . . . . . . . . .
378 MAINTAINING YOUR VEHICLE 2.
MAINTAINING YOUR VEHICLE 379 2.
380 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE Loose Fuel Filler Cap Message After fuel is added, the vehicle diagnostic system can determine if the fuel filler cap is loose, improperly installed, or damaged. A gASCAP message will be displayed in the instrument cluster. Tighten the gas cap until a 9clicking9 sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started.
382 MAINTAINING YOUR VEHICLE Your vehicle has a simple ignition key-actuated test, which you can use prior to going to the test station. To check if your vehicle’s OBD II system is ready, you must do the following: 1. Insert your ignition key into the ignition switch. 2. Turn the ignition to the ON position, but do not crank or start the engine. 3. If you crank or start the engine, you will have to start this test over. 4.
MAINTAINING YOUR VEHICLE 383 serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL is on with the engine running. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. REPLACEMENT PARTS Use of genuine Mopart parts for normal/scheduled maintenance and repairs is highly recommended to ensure the designed performance.
384 MAINTAINING YOUR VEHICLE MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance. However, if a malfunction of these items does occur, it could adversely affect the engine or vehicle performance.
MAINTAINING YOUR VEHICLE Checking the oil while the vehicle is on level ground, will improve the accuracy of the oil level readings. Maintain the oil level between the MIN and MAX markings on the dipstick. Adding one quart of oil when the reading is at the MIN mark will result in a MAX reading on these engines.
386 MAINTAINING YOUR VEHICLE whichever comes first, and follow schedule “B—All Engines” of the 9Maintenance Schedules9 section of this manual. If none of these apply to you, and your vehicle is equipped with a Non–Turbo Charged Engine then change your engine oil at every interval shown on schedule “A”—NON TURBO in the maintenance schedule section of this manual.
MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) — 2.4L and 2.4L Turbo Engines SAE 5W-30 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to the “Engine Compartment” illustration in this section.
388 MAINTAINING YOUR VEHICLE Engine Oil Filter Selection All of this manufacturers engines have a full-flow type disposable oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high quality filters should be used to assure most efficient service. Mopar Engine Oil Filters are high quality oil filters and are recommended. Special tools are required to properly measure tension and to restore belt tension to factory specifications.
MAINTAINING YOUR VEHICLE CATALYTIC CONVERTER The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.
390 MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE Check ventilation hose for indication of damage or plugging deposits. Replace if necessary. FUEL FILTER A plugged fuel filter can cause hard starting or limit the speed at which a vehicle can be driven. Should an excessive amount of dirt accumulate in the fuel tank, frequent filter replacement may be necessary. The fuel filters are located inside the fuel tank. See your dealer for service.
392 MAINTAINING YOUR VEHICLE MAINTENANCE-FREE BATTERY You will never have to add water, nor is periodic maintenance required. CAUTION! When servicing the battery, always reinstall the battery thermowrap. The thermowrap provides battery heat protection and will extend overall battery life. Failure to reinstall the thermowrap can result in evaporative loss of the battery fluid. WARNING! Battery fluid is a corrosive acid solution and can burn or even blind you.
MAINTAINING YOUR VEHICLE CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion. Apply grease to posts and clamps after tightening.
394 MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information book for further warranty information. • The air conditioning system contains refrigerant under high pressure.
MAINTAINING YOUR VEHICLE WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Fluids, Lubricants, and Genuine Parts for correct fluid types.
396 MAINTAINING YOUR VEHICLE amount of a high quality lubricant such as Mopart Lock Cylinder Lubricant directly into the lock cylinder. WINDSHIELD WIPER BLADES Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non abrasive cleaner or use the washer solvent. This will remove accumulations of salt, waxes or road film and help reduce streaking and smearing.
MAINTAINING YOUR VEHICLE checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water. WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution.
398 MAINTAINING YOUR VEHICLE COOLING SYSTEM WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position. • You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool.
MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush and Refill The system should be drained, flushed, and refilled at the intervals shown in the “Maintenance Schedules” in Section 8 of this manual. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of old antifreeze solution.
400 MAINTAINING YOUR VEHICLE Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to five Years or 100,000 miles before replacement. To prevent reducing this extended maintenance period, it is important that you use the same coolant throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) coolant.
MAINTAINING YOUR VEHICLE The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system.
402 MAINTAINING YOUR VEHICLE The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for coolant freeze point or replacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill.
MAINTAINING YOUR VEHICLE • Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean, also. 403 Pay particular attention to the hoses nearest to high heat sources such as the exhaust manifold. Inspect hose routing to be sure hoses do not touch any heat source or moving component that may cause heat damage or mechanical wear.
404 MAINTAINING YOUR VEHICLE FUEL SYSTEM CONNECTIONS Electronic Fuel Injection high pressure fuel systems are designed with tubes and special connects, connections and clamps which have unique material characteristics to provide adequate sealing and resist attack by deteriorated gasoline. You are urged to use only the manufactures-specified tubes, connections and clamps, or their equivalent in material and specification, in any fuel system servicing.
MAINTAINING YOUR VEHICLE brittle rubber, cracking, tears, cuts, abrasions, and excessive swelling suggest deterioration of the rubber. Particular attention should be made to examining those hose surfaces nearest to high heat sources, such as the exhaust manifold. Inspect all hose clamps and couplings to make sure they are secure and no leaks are present. Insure nylon tubing in these areas has not melted or collapsed.
406 MAINTAINING YOUR VEHICLE Master Cylinder - Brake Fluid Level Check Check the fluid level in the master cylinder immediately if the brake system warning light indicates system failure. Check the fluid level in the master cylinder when performing underhood services. Clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reservoir.
MAINTAINING YOUR VEHICLE 407 WARNING! WARNING! Use of a brake fluid that has a lower initial boiling point than the recommended MOPARt DOT 3 product or a brake fluid that is unidentified as to FMVSS specification may result in sudden brake failure during hard prolonged braking. You could have an accident. Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire.
408 MAINTAINING YOUR VEHICLE AUTOMATIC TRANSAXLE The automatic transaxle and differential assembly are contained within a single housing. The fluid level in the automatic transaxle should be checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly reduce the life of the transaxle and the fluid. FLUID LEVEL CHECK — FOUR-CYLINDER ENGINES Use the following procedure to check the automatic transaxle fluid level properly: 1. Park the vehicle on level ground. 2.
MAINTAINING YOUR VEHICLE 409 If the fluid level is low, add sufficient fluid through the filler (dipstick) tube to bring it to the proper level. Do not overfill. Fluid And Filter Changes Automatic transmission fluid and filter should be changed as follows: CAUTION! Maintenance schedule “A”—Non Turbo Charged Engines – No change necessary. • Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder.
410 MAINTAINING YOUR VEHICLE If the transaxle is disassembled for any reason, the fluid and filter should be changed. Special Additives Automatic Transmission Fluid (ATF) is an engineered product and its performance may be impaired by supplemental additives. Therefore, do not add any fluid additives to the transaxle. The only exception to this policy is the use of special dyes to aid in detecting fluid leaks. In addition, avoid using transmission sealers as they may adversely affect seals.
MAINTAINING YOUR VEHICLE APPEARANCE CARE AND PROTECTION FROM CORROSION Protection Of Body And Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
412 MAINTAINING YOUR VEHICLE • If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopart Super Kleen Bug and Tar Remover to remove. • Use Mopart Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.
MAINTAINING YOUR VEHICLE 413 • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. cleaner. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. Interior Care • Use Mopar touch up paint on scratches as soon as possible.
414 MAINTAINING YOUR VEHICLE Cleaning Leather Upholstery Mopart Total Clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopart Total Clean. Care should be taken to avoid soaking your leather upholstery with any liquid.
MAINTAINING YOUR VEHICLE • For grease stains, apply Mopart Multi-Purpose Cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • Do not use any solvents or protectants on Yes Essentialst products. Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.
416 MAINTAINING YOUR VEHICLE Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. Replace the belts if they appear frayed or worn or if the buckles do not work properly. 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag.
MAINTAINING YOUR VEHICLE 417 CAUTION! CAUTION! Avoid high pressure car washes, as they can damage the top material. Also, increased water pressure may force water past the weather strips. Never use an abrasive type cleaner or bleaches. Cleaners should not contain silicones, organic solvents, petroleum distillates or plasticizers. always wait until the top is thoroughly dry before lowering it into the storage area.
418 MAINTAINING YOUR VEHICLE Cloth Top Additional Cleaning Procedure For additional cleaning assistance in removing stubborn stains, apply Mopar Convertible Cloth Top Cleaner (part number 05012245AA) to the complete stain, extending 2 inches (50 mm) beyond the stain. With a soft bristle brush, scrub in all directions over the stain. Avoid heavy scrubbing. Rinse the area with warm water. If the stain is still apparent, repeat the cleaning procedure.
MAINTAINING YOUR VEHICLE INTEGRATED POWER MODULE (IPM) An Integrated Power Module is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. A description of each fuse and component may be stamped on the inside of the cover.
420 6 7 8 9 10 11 MAINTAINING YOUR VEHICLE INTEGRATED POWER MODULE (IPM) Cartridge Cavity Mini Fuse Description Fuse IOD Sw/ Pwr Mir/ 10 Amp Red Ocm Steering Cntrl Sdar/Hfm 30 Amp IOD Sense1 Green 30 Amp IOD Sense2 Green 40 Amp Power Seats Green CCN, 20 Amp YelPower low Locks 15 Amp Lt Power OutBlue let 12 13 14 15 16 INTEGRATED POWER MODULE (IPM) Cartridge Cavity Mini Fuse Description Fuse 20 Amp Yel- Ign Run/ low Acc Inverter Pwr run/ 20 Amp YelAcc Outlet low RR IOD CCN/ 10 Amp Red Interior Light
MAINTAINING YOUR VEHICLE 17 18 19 20 21 INTEGRATED POWER MODULE (IPM) Cartridge Cavity Mini Fuse Description Fuse IOD Feed 10 Amp Red CVT Mod/ Mod_Wcm ASD Relay 40 Amp Contact Green PWR Feed PWR Amp 20 Amp 1 & Amp 2 Yelow Feed 15 Amp Lt. IOD Feed Blue Radio IOD Feed 10 Amp Red Intrus Mod/Siren 22 23 24 25 26 421 INTEGRATED POWER MODULE (IPM) Cartridge Cavity Mini Fuse Description Fuse IGN RUN Hvac/ 10 Amp Red Compass Sensor ENG ASD 15 Amp Lt.
422 27 28 29 30 31 32 MAINTAINING YOUR VEHICLE INTEGRATED POWER MODULE (IPM) Cartridge Cavity Mini Fuse Description Fuse IGN RUN 10 Amp Red Only ORC Feed IGN RUN 10 Amp Red ORC/OCM Feed EMPTY 20 Amp Yel- Heated low Seats Headlamp 10 Amp Red Washer Relay Control ENG ASD 30 Amp Control Pink Feed 1 33 34 35 36 37 INTEGRATED POWER MODULE (IPM) Cartridge Cavity Mini Fuse Description Fuse ABS MOD/ 10 Amp Red J1962 Conn/PCM 30 Amp ABS Valve Pink Feed 40 Amp ABS Pump Green Feed Headlamp 30 Amp Washer Pink Co
MAINTAINING YOUR VEHICLE CAUTION! • When installing the Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
424 MAINTAINING YOUR VEHICLE REPLACEMENT BULBS LIGHT BULBS — Inside Bulb No. Center Console Floor Lamp . . . . . . . . . . . . . . . . . T37 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 6233137 Console Gear Selector . . . . . . . . . . . . . . . . . . . PC194 Dome Light (sedan) . . . . . . . . . . . . . . . . . . . . . . T579 Dome Light / Sport Bar Lights (convertible) . . . . T904 Instrument Cluster Illumination . . . . . . . . . . . . . . 74 Overhead Reading Light (Overhead Console) . .
MAINTAINING YOUR VEHICLE 425 BULB REPLACEMENT Headlights CAUTION! Do not touch the new headlight bulb with your fingers. Oil contamination will severely shorten bulb life. 1. Remove the headlight access cover splash shield, located in the front wheel well opening. 2. Disconnect the electrical connector. 3. Rotate the socket to the left one quarter turn and replace the bulb.
426 MAINTAINING YOUR VEHICLE Front Park/Turn Signal/Side Marker Lights Front Fog Lights — If Equipped 1. Remove the headlight access cover splash shield, located in the front wheel well opening. 1. Remove the fasteners attaching the lower splash shield to gain access to the fog light. 2. Rotate the socket to the left one quarter turn to replace and replace the bulb. 2. Twist and remove the bulb from the fog light housing. 3. Disconnect the electrical connector and replace bulb.
MAINTAINING YOUR VEHICLE Tail/Stop, and Rear Turn Signal Lights 3. Pull the bulb out of the socket and replace. 1. Remove the screw attaching the tail light housing and remove the housing from the vehicle. Back Up Lights 427 2. Twist the bulb socket 1/4 turn to remove it from the housing.
428 MAINTAINING YOUR VEHICLE 1. To remove the backup lamp, you must take a fiber stick and slide it along the inboard side of the lamp and compress a spring clip to allow it to partially 9pop9 out to the secondary catch. 2. Fully compress the clip to get the lamp to come out completely. 3. Remove the socket from the housing. 4. Pull the bulb out of the socket and replace. Center High Mounted Stop Light 1. Open the liftgate and remove the liftgate CHMSL cover. 2.
MAINTAINING YOUR VEHICLE 429 FLUIDS AND CAPACITIES FLUIDS AND CAPACITIES U.S. 15 Gallons Fuel (Approximate) Engine Oil-With Filter 2.4 Liter Engines (Use API Certified 5.0 qts SAE 5W-30 Engine Oil.) Cooling System * 2.4 Liter Engines (Mopart Antifreeze/Coolant 5 Year/100,000 6.5 qts Miles Formula), or equivalent. * Includes heater and coolant recovery bottle filled to MAX level. Metric 56.7 Liters 4.7 Liters 6.
430 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS ENGINE FLUIDS, LUBRICANTS AND GENUINE PARTS Component Fluids, Lubricants and Genuine Parts Mopart Antifreeze/Coolant 5 Year/100,000 Mile ForEngine Coolant mula HOAT (Hybrid Organic Additive Technology) or equivalent. Use API Certified SAE 5W-30 Engine Oil. Refer to your Engine Oil (2.4L Standard, 2.4L Standard Turbo) engine oil filler cap for correct SAE grade meeting DaimlerChrysler Material Standard MS-6395.
MAINTAINING YOUR VEHICLE 431 CHASSIS Component Automatic Transmission Fluid Manual Transmission Fluid Brake Master Cylinder Power Steering Reservoir FLUIDS, LUBRICANTS AND GENUINE PARTS Fluids, Lubricants and Genuine Parts. Mopart ATF+4 Automatic Transmission Fluid. Mopart ATF+4 Automatic Transmission Fluid MS9602. Mopart DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids or equivalent.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E m Emissions Control System Maintenance . . . . . . . 434 ▫ Schedule “A”—Non Turbo . . . . . . . . . . . . . . . 448 m Maintenance Schedule . . . . . . . . . . . . . . . . . . . 434 ▫ Schedule “A”—Turbo . . . . . . . . . . . . . . . . . . 453 C ▫ Schedule “B”—All Engines . . . . . . . . . . . . . .
M A I N T E N A N C E 434 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES • Taxi, police, or delivery service (commercial service).†L • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow schedule “B—All Engines” of the 9Maintenance Schedules9 section of this manual.
M 436 MAINTENANCE SCHEDULES A I At Each Stop for Fuel N T • Check the engine oil level about 5 minutes after a fully E warmed engine is shut off. Checking the oil level while N A the vehicle is on level ground will improve the accuN racy of the oil level reading. Add oil only when the C level is at or below the ADD or MIN mark. E S C H E D U L E S 8 • Check the windshield washer solvent and add if required. • Check all lights and all other electrical items for correct operation.
SCHEDULE “B”—ALL ENGINES SCHEDULE “B”—ALL ENGINES Follow schedule “B”—All Engines if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (100 000 km) if the vehicle is usually operated under one or more of the conditions marked with an L. Change the manual transaxle fluid every 48,000 miles (80 000 km) if the vehicle is usually operated under one or more of the conditions marked with an †.
M A I N T E N A N C E 438 SCHEDULE “B”—ALL ENGINES NOTE: IF ANY of these apply to you then flush and replace the engine coolant every 102,000 miles (170 000 km) or 60 months, whichever comes first, and follow schedule “B—All Engines” of the 9Maintenance Schedules9 section of this manual.
SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter, replace as necessary.* Inspect the Make-up air filter, replace as necessary.
M 440 SCHEDULE “B”—ALL ENGINES A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace as necessary.* Replace the Make-up air filter. Adjust the generator drive belt tension.
SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Change the brake fluid. If vehicle is used for trailer towing. Inspect the engine air cleaner filter, replace as necessary.* Change the manual transaxle fluid.† Inspect the Make-up air filter. Replace as necessary.
M 442 SCHEDULE “B”—ALL ENGINES A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Replace the Make-up air filter. Adjust the generator drive belt tension.
SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter and replace as necessary.* Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Inspect the Make-up air filter, replace as necessary. Adjust the generator drive belt tension.
M 444 SCHEDULE “B”—ALL ENGINES A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not reA placed at 3 months. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Change the brake fluid. If vehicle is used for trailer towing. Inspect the engine air cleaner filter and replace as necessary.* Change the manual transaxle fluid.† Replace the engine timing belt. * Flush and replace the engine coolant, if not replaced at 60 months.
SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. * Inspect the tie rod ends and boot seals. Replace the Make-up air filter. Adjust the generator drive belt tension. Change automatic transaxle fluid and filter.L Inspect the PCV valve and replace if necessary. *‡ Flush and replace the engine coolant at 120 months, if not replaced at 102,000 miles.
M 446 SCHEDULE “B”—ALL ENGINES A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not reA placed at 3 months. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Inspect the engine air cleaner filter and replace as necessary.
SCHEDULE “B”—ALL ENGINES Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. * Replace the spark plugs. Change the manual transaxle fluid.† Replace the Make-up air filter. Inspect the PCV valve and replace if necessary. *‡ 138,000 (230 000) X * This maintenance is recommended by the manufacturer to the owner, but is not required to maintain the emissions warranty.
M 448 SCHEDULE “A”—NON TURBO A I SCHEDULE “A”—NON TURBO N T Miles E N (Kilometers) A [Months] N C Change engine oil and engine oil filter. E Rotate tires. S C H E D U L E S 8 Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the Make-up air filter.
SCHEDULE “A”—NON TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace, if necessary.* Flush and replace the engine coolant at 60 months, if not done at 102,000 miles. Replace the Make-up air filter. Adjust the generator drive belt tension.
M 450 SCHEDULE “A”—NON TURBO A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Replace the engine air cleaner filter. Replace the spark plugs. Replace the engine timing belt. * Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Replace the Make-up air filter. Adjust the generator drive belt tension.
SCHEDULE “A”—NON TURBO 451 M Miles 108,000 114,000 120,000 126,000 132,000 138,000 (Kilometers) (180 000) (190 000) (200 000) (210 000) (220 000) (230 000) [Months] [108] [114] [120] [126] [132] [138] Change engine oil and engine oil filter. X X X X X X Rotate tires. X X X X X X Inspect the PCV valve and replace if necessary. * ‡ X Replace the air cleaner filter. X Flush and replace the engine coolant at 120 X months, if not done at 102,000 miles. Replace the spark plugs and ignition cables.
M 452 SCHEDULE “A”—NON TURBO A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Inspect the PCV valve and replace if necessary. * ‡ S C H E D U L E S 8 Replace the air cleaner filter. * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emissions warranty. ‡ This maintenance is not required if previously replaced.
SCHEDULE “A”—TURBO 453 M SCHEDULE “A”—TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the Make-up air filter. Adjust the generator drive belt tension.
M 454 SCHEDULE “A”—TURBO A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Flush and replace engine coolant at 60 months, if not replaced at 100,000 miles.
SCHEDULE “A”—TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Replace the Make-up air filter. Adjust the generator drive belt tension.
M 456 SCHEDULE “A”—TURBO A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Replace the engine air cleaner filter. Replace the spark plugs. Adjust the generator drive belt tension. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Flush and replace the engine coolant if not done at 60 months. Replace the Make-up air filter.
SCHEDULE “A”—TURBO Miles (Kilometers) [Month] Change engine oil and engine oil filter. Rotate tires. Inspect the PCV Valve and replace if necessary. * Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emissions warranty. ‡ This maintenance is not required if previously replaced.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461 ▫ In Mexico Contact . . . . . . . . . . . . . . . . . . . . . 462 ▫ Prepare For The Appointment . . . . . . . . . . . . 461 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . . 463 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 461 ▫ Service Contract . . . . . . . . . . . . . . . . . . . .
460 IF YOU NEED CONSUMER ASSISTANCE m Publication Order Forms . . . . . . . . . . . . . . . . . . 465 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . 467 m Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 467 ▫ Temperature Grades . . . . . . . . . . . . . . . . . . . 468 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
462 IF YOU NEED CONSUMER ASSISTANCE special tools, and the latest information to ensure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your authorized dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealership. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
464 IF YOU NEED CONSUMER ASSISTANCE WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain, or emit, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WARRANTY INFORMATION (U.S.
IF YOU NEED CONSUMER ASSISTANCE 465 To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov. PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below.
466 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-bystep troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.
IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle. All passenger car tires must conform to Federal safety requirements in addition to these grades.
468 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
470 INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . 308 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 400 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 340 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 218 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 338 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 391 Air Conditioner Maintenance . . . . . . . . . . . . . . . 393 Air Conditioning Controls . . . . . . . . . . . . . .
INDEX Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297 Special Additives . . . . . . . . . . . . . . . . . . . . . . 410 Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299 Back-Up Lights . . . . . . . . . . . . . . . . . . . . . . . . . 427 Ball Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392 Keyless Transmitter Replacement (RKE) . . . . . 29,35 Belts, Drive . . . . . .
472 INDEX Cargo Compartment Luggage Carrier . . . . . . . . . . . . . . . . . . . . . . . 215 Carrier, Luggage . . . . . . . . . . . . . . . . . . . . . . . . 215 Catalytic Converter . . . . . . . . . . . . . . . . . . . . . . 389 Caution, Exhaust Gas . . . . . . . . . . . . . . . . . . . . . 115 CD (Compact Disc) Player . . . . . . . . . . . . . . . 251,259 CD (Compact Disc) Player Maintenance . . . . . . . . 277 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . .
INDEX Convertible Top Maintenance . . . . . . . . . . . . . . . 416 Convertible Top Manual Override . . . . . . . . . 134,373 Cool Down, Turbo . . . . . . . . . . . . . . . . . . . . . . . 293 Coolant (Antifreeze) . . . . . . . . . . . . . . . . . . . 429,430 Coolant Pressure Cap (Radiator Cap) . . . . . . . . . . 400 Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . 398 Adding Coolant (Antifreeze) . . . . . . . . . . . . . . 400 Coolant Level . . . . . . . . . . . . . . . . . . . . . .
474 INDEX Door Opener, Garage . Downshifting . . . . . . Drive Belts . . . . . . . . Driver’s Seat Back Tilt Driving On Slippery Surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 304 388 167 . . . . . . . . . . . . . . . . . . . . 369 Electric Rear Window Defrost . . . . . . . . . . . . . . . 217 Electric Remote Mirrors . . . . . . . . . . . . . . . . . . .
INDEX Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337 Event Data Recorder . . . . . . . . . . . . . . . . . . . 70,105 Exhaust Gas Caution . . . . . . . . . . . . 38,39,115,339,397 Exhaust System . . . . . . . . . . . . . . . . . . . . . . . . . 397 Fabric Care . . . . . . . . . . . . . . . . . . . . . . . . . 413,414 Filler Location Fuel . . . . . . . . . . . . . . . . . . . . 226,340 Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . .
476 INDEX Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337 Filler Cap (Gas Cap) . . . . . . . . . . . . . . . . . 226,340 Filler Door (Gas Cap) . . . . . . . . . . . . . . . . . . . 226 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391 Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337 Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404 Light . . . . . . . .
INDEX Headlights Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 425 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415 High Beam . . . . . . . . . . . . . . . . . . . . . . . . 189,234 High Beam/Low Beam Select Switch . . . . . . . . 189 Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 Heated Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 Hitches Trailer Towing . . .
478 INDEX Key, Sentry (Immobilizer) . . . . . . . Key-In Reminder . . . . . . . . . . . . . Keyless Entry System (Convertible) Keyless Entry System (Sedan) . . . . Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 15 30 24 13 Lane Change and Turn Signals . . . . . . . . . . . . . . 230 Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . . 45,82 Latches Hood . . . . .
INDEX Theft Alarm (Security Alarm) . . . . . . . . . . . . . . 233 Tire Pressure Monitoring (TPMS) . . . . . . . . . . . 332 Traction Control . . . . . . . . . . . . . . . . . . . . . . . 312 Turn Signal . . . . . . . . . . . . . . . . . . 186,189,230,426 Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 Warning (Instrument Cluster Description) . . . . . 226 Loading Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 342 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . .
480 INDEX Mini-Trip Computer . . . . . . . . . . . . . . . . . . . . . . 235 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Electric Remote . . . . . . . . . . . . . . . . . . . . . . . 137 Outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 Rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Vanity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 Modifications/Alterations, Vehicle . . . . . . . . . . . . .
INDEX Overheating, Engine . . . . . . . . . . . . . . . . . . . . . . 358 Owner’s Manual (Operator Manual) . . . . . . . . . 4,465 Paint Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411 Panel Rear Shelf . . . . . . . . . . . . . . . . . . . . . . . . 210 Panic Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . 26,32 Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . 305 Passenger Seat Back Tilt (Easy Entry System) . . . . 168 Passing Light . . . . . . . . . . . . . .
482 INDEX Radio (Sound Systems) . . . . . . . . . . . . . . . . . 251,259 Rear Liftgate (Sedan) . . . . . . . . . . . . . . . . . . . . . . 37 Rear Seat, Folding . . . . . . . . . . . . . . . 171,173,175,177 Rear Seat Removal . . . . . . . . . . . . . . . . . . . . . . . 181 Rear Shelf Panel . . . . . . . . . . . . . . . . . . . . . . . . 210 Rear Window . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Rear Window Defroster . . . . . . . . . . . . . . . . . . . 217 Rear Window Features . . . . . .
INDEX Adjustable Upper Shoulder Anchorage . . . . . . . . 52 And Pregnant Women . . . . . . . . . . . . . . . . . 54,89 Child Restraint . . . . . . . . . . . . . . . . . . . . . . 72,107 Front Seat . . . . . . . . . . . . . . . . . . . . . . . . . . 45,82 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . 53,88 Rear Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . 45,82 Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232 Untwisting Procedure . . . . . . . . . . . . . .
484 INDEX Severe Service . . . . . . . . . . . . . . . . . . . . . . . . . . 437 Shift Speeds, Manual Transaxle . . . . . . . . . . . . . . 304 Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . . . 45,82 Side Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . 65,100 Side Window Demisters (Defrosters) . . . . . . . . . . 285 Slippery Surfaces, Driving On . . . . . . . . . . . . . . . 369 Snow Chains (Tire Chains) . . . . . . . . . . . . . . . . . 330 Snow Tires . . . . . . . . . . . . .
INDEX Tire Identification Number (TIN) . . . . . . . . . . . . . 316 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . 313 Tire Safety Information . . . . . . . . . . . . . . . . . . . . 313 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 117,321,467 Aging (Life of Tires) . . . . . . . . . . . . . . . . . . . . 327 Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 321 Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . 329 Chains . . . . . . . . . . .
486 INDEX Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . 343 Cooling System Tips . . . . . . . . . . . . . . . . . . . . 355 Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345 Minimum Requirements . . . . . . . . . . . . . . . . . 349 Trailer and Tongue Weight . . . . . . . . . . . . . . . . 348 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353 Trailer Towing Guide . . . . . . . . . . . . . . . . . . . . . 347 Trailer Weight . . . . . . . . . . .
INDEX Universal Transmitter . . . . . . . Unleaded Gasoline . . . . . . . . . Untwisting Procedure, Seat Belt Upholstery Care . . . . . . . . . . ............. ............. ............ ............. . 197 . 337 52,88 . 413 Vacuum/Vapor Harnesses . . . . . . . . . . . . . . . . . 403 Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . 138 Variance, Compass . . . . . . . . . . . . . . . . . . . . . . . 236 Vehicle Identification Number (VIN) . . . . . . . . . . . . 6 Vehicle Loading . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
2nd Edition First Edition Printed in U.S.A.
