2008 Aspen 2008 OWNER’ S MANUAL 81-026-0850 First Edition Printed in U.S.A.
TABLE OF CONTENTS SECTION PAGE .............................................................3 1 1 INTRODUCTION 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4 INSTRUMENT PANEL AND CONTROLS 5 STARTING AND OPERATING 6 WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .365 6 7 MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS m Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m Warnings And Cautions . . . . . . . . . . . . . . . . . . . 7 m Rollover Warning . . . . . . . . . . . . . . . . . . . . . . . . 4 m Vehicle Identification Number . . . . . . . . . . . . . . . 7 m How To Use This Manual . . . . . . . . . . . . . . . . . . 5 m Vehicle Modifications/Alterations . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. HOW TO USE THIS MANUAL Consult the Table of Contents to determine which section contains the information you desire. The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects.
6 INTRODUCTION
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all WARNINGS and CAUTIONS. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield.
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . . .12 m Security Alarm System — If Equipped . . . . . . . . .18 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .12 ▫ To Set The Alarm . . . . . . . . . . . . . . . . . . . . . .19 ▫ Locking Doors With The Key . . . . . . . . . . . . . .13 ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .19 m Sentry Keyt . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ General Information . . . . . . . . . . . . . . . . . . . .25 ▫ Window Lockout Switch . . . . . . . . . . . . . . . . .36 ▫ Programming Additional Transmitters . . . . . . . .25 m Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 ▫ Battery Replacement . . . . . . . . . . . . . . . . . . . .27 ▫ Power Liftgate — If Equipped . . . . . . . . . . . . .38 m Remote Starting System — If Equipped . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Seat Belts And Pregnant Women . . . . . . . . . . . .52 m Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . .53 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . . .75 ▫ Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbags . . . . . . . . . . .53 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The authorized dealer that sold you your vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer. Ask your authorized dealer for these numbers and keep them in a safe place. Ignition Key Removal Automatic Transmission Place the shift lever in PARK. Turn the ignition switch to the LOCK position and remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If you try to remove the key before you place the shift lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system uses ignition keys which have an embedded electronic chip (transponder) to prevent unauthorized vehicle operation. Therefore, only keys that are programmed to the vehicle can be used to start and operate the vehicle. The system will shut the engine off in two seconds if someone uses an invalid key to try to start the engine.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE starting the vehicle. Cell phones, pagers, or other RF electronics will not cause interference with this system. All of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a Sentry Keyt is programmed to a vehicle, it cannot be programmed to any other vehicle.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Insert the first valid key into the ignition switch. Turn the ignition switch to the ON position for at least three seconds, but no longer than 15 seconds. Then, turn the ignition switch to the LOCK position and remove the first key. 3. Insert the second valid key into the ignition switch. Turn the ignition switch to the ON position within 15 seconds. After 10 seconds, a chime will sound.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information The Sentry Keyt system complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 2 • This device may not cause harmful interference. • This device must accept any interference that may be received, including interference that may cause undesired operation.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! The key cannot be turned to LOCK until the shift lever is in the PARK position. Do not attempt to pull the shift lever out of PARK after the key is in the LOCK position. NOTE: The steering wheel will lock when the key is removed, and when the steering wheel is turned around 115 degrees clockwise or 65 degrees counterclockwise from the center position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Set the Alarm: The Security Alarm System will set when you use the power door locks or use the Remote Keyless Entry Transmitter to lock the doors. After all the doors are closed and locked, the security light in the instrument cluster will flash rapidly to signal that the system is arming. The Security light in the instrument panel cluster will flash rapidly for about 15 seconds to indicate that the alarm is being set.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE vehicle and lock the doors with the transmitter, the alarm will sound when you pull the door handle to exit. NOTE: You may accidentally activate the Security Alarm System (horn sounds and lights flash) by entering the vehicle without using the key fob to unlock the door(s). The Security Alarm System can be disarmed with the key fob’s UNLOCK button or by inserting a programmed Sentry Keyt into the ignition and turning the key to the ON position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY 21 NOTE: Your vehicle’s key fob may have three, four or five buttons (shown), depending on the optional features purchased with your vehicle. This system allows you to lock or unlock the doors and liftgate or activate the panic alarm from distances a minimum of 66 ft (20 m) using a hand-held radio transmitter. The transmitter need not be pointed at the vehicle to activate the system.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system can be programmed to unlock all the doors upon the first UNLOCK button press by following these procedures: • For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to “Personal Settings (Customer Programmable Features)” under “Overhead Console with Electronic Vehicle Information Center (EVIC) – If Equipped” in Section 3. • For vehicles not equipped with the EVIC: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Horn Chirp Programming The horn chirp feature will be activated when shipped from the assembly plants. If desired, this feature can be disabled by following these procedures: • For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to “Personal Settings (Customer Programmable Features)” under “Overhead Console with Electronic Vehicle Information Center (EVIC) – If Equipped” in Section 3. 23 5.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the following procedure: 5. If the desired programming was not achieved or to reactivate this feature, repeat the above steps. 1. Press and hold the UNLOCK button on the key fob. Using the Panic Alarm To activate the PANIC mode, while the ignition is OFF, press and release the PANIC button on the transmitter once.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Fasten your seat belt. Fastening the seat belt will cancel any chiming that may confuse you during this programming procedure. 8. Using the key fob to be programmed, press and release both the LOCK and UNLOCK buttons simultaneously. 3. Place the key into the ignition. 9. A single chime will be heard. 4. Turn the ignition to the ON position. Do not start the engine. 10.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 Battery Replacement The recommended replacement battery is CR2032. NOTE: Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/ perchlorate. 2 1. If the key fob is equipped with a screw, remove the screw. With the transmitter buttons facing down, use a flat blade to pry the two halves of the transmitter apart. Make sure not to damage the elastomer seal during removal. Separating Transmitter Halves 2.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. To reassemble the transmitter case, snap the two halves of the case together. Make sure there is an even “gap” between the two halves. If equipped, install and tighten the screw until snug. Test transmitter operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To enter the vehicle while the engine is running during a remote start, you must first unlock the vehicle using the UNLOCK button on the key fob. After the vehicle is unlocked, you have 60 seconds to enter the vehicle, insert the key in the ignition and move it to the RUN position; otherwise, the engine will cancel remote start and automatically turn off.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. • Never leave unattended children alone in a vehicle. Leaving children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Door Locks If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h).
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Unlock On Exit — If Equipped This feature unlocks all of the doors of the vehicle when any door is opened (excluding the liftgate). This will occur only after the vehicle has been shifted into the PARK position after the vehicle has been driven (shifted out of PARK and all doors closed). This feature will not operate if there is any manual operation of the power door locks (LOCK or UNLOCK).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 8. If a chime is not heard, the program mode was canceled before the feature could be changed. If necessary, repeat the above procedure. 2 Child Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the child protection door lock system. Child Lock To use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child protection locks.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WINDOWS Power Windows Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE windows will operate only when the ignition switch is turned to the ON position and for 10 minutes after the ignition is turned OFF or the driver’s door is opened. This feature can be turned off by your authorized dealer. NOTE: The Power Accessory Delay feature will allow the power windows to operate for 10 minutes after the ignition it turned OFF. WARNING! Never leave children alone in a vehicle.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the window runs into any obstacle during the auto-closure, it will reverse direction and then stop. Remove the obstacle and use the window switch again to close the window. Any impact due to rough road conditions may trigger the auto reverse function unexpectedly during auto-closure. If this happens, pull the switch lightly to the first detent and hold to close the window manually.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 pressing the remote transmitter UNLOCK button prior to activating the power liftgate; otherwise, the engine will stop automatically. Window Lockout Switch LIFTGATE The liftgate can be unlocked using the Remote Keyless Entry (RKE) Transmitter or by activating the power door lock switches located on the front doors.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The liftgate will not manually open if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h). NOTE: If the liftgate is locked and is not equipped with a powered liftgate, pressing the button on the RKE Transmitter will result in the liftgate becoming unlocked for 30 seconds allowing you to manually access the liftgate area. The liftgate will re-lock automatically within 10 seconds once the liftgate is closed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear. Make sure the liftgate is closed and latched before driving away. A beeping signal will sound two seconds before the liftgate starts to open or close. NOTE: • If anything obstructs the power liftgate while it is closing or opening, the liftgate will automatically reverse to the closed or open position, provided it meets sufficient resistance.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The power liftgate will not operate in temperatures below 222°F (230°C) or temperatures above 150°F (65°C). Be sure to remove any buildup of snow or ice from the liftgate before pressing any of the power liftgate buttons. • If the power liftgate encounters multiple obstructions within the same cycle, the system will automatically stop and must be opened or closed manually.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, knee bolsters, front airbags for both the driver and front passenger, and left and right side curtain airbags for the driver and passengers seated next to a window.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Research has shown that seat belts save lives, and that they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions in your vehicle have combination lap/shoulder belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. 45 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! Adjustable Upper Shoulder Belt Anchorage In the front and second row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a guide, if you are shorter than average you will prefer a lower position, and if you are taller than average you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in the desired position. Pull the seatback forward to ensure that it is locked in the upright position. WARNING! A 20% seatback that is not fully latched in the upright position will not protect you properly.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Use The Automatic Locking Mode 1. Buckle the combination lap/shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 WARNING! • If the small (keyed buckle) latch plate and keyed buckle are not properly connected when the seat belt is used by an occupant, the seat belt will not be able to provide the proper restraint and will increase the risk of injury in a collision. • When reattaching the small (keyed buckle) latch plate and keyed buckle, ensure the seat belt webbing is not twisted.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To reattach the seat belt to the third row center seat, pull the small (keyed buckle) latch plate forward from the headliner slots and insert it into the keyed buckle until there is an audible click. Refer to the previous section for the proper seat belt usage.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints. NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly. The pretensioners are triggered by the Occupant Restraint Controller (ORC). Like the airbags, the pretensioners are single use items.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE or START position. DaimlerChrysler does not recommend deactivating the Enhanced Warning System (BeltAlertt). 1. Turn the ignition switch to the OFF position and buckle the driver’s seat belt. DO NOT start the engine or press the TRIP RESET button. 4. Programming mode will be cancelled after the feature has toggled with the seat belt still buckled or if the ignition switch is turned to the LOCK position or 10 seconds after the feature has toggled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision. 53 Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbags 2 Seat Belt Extender If a seat belt is too short even when fully extended, your authorized dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE in the instrument panel, above the glove compartment. The words SRS/AIRBAG are embossed on the airbag covers. NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Do not use a clothing bar mounted to the coat hooks in this vehicle. A clothing bar will impede the proper performance of the window bags. Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Window bags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. If your vehicle has window bags, do not lean against the door or window. Airbags will inflate forcefully into the space between you and the door. 5. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Refer to 9If You Need Customer Assistance9 in Section 9. WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag System Components The airbag system consists of the following: • Occupant Restraint Controller • Side Remote Acceleration Sensors • Airbag Warning Light • Driver Airbag • Passenger Airbag • Window Bags above Side Windows • Steering Wheel and Column • Instrument Panel • Interconnecting Wiring • Knee Impact Bolsters • Front Acceleration Sensors 57 • Driver and Front Passenger Seat Belt Pretensioners How the Airbag System Works • The Occupant Restraint Cont
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Also, the ORC turns on the AIRBAG warning light in the instrument cluster for six to eight seconds for a self-check when the ignition is first turned on. After the self-check, the AIRBAG warning light will turn off. If the ORC detects a malfunction in any part of the system, it turns on the AIRBAG warning light either momentarily or continuously. A single chime will sound if the light comes on again after initial start up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Side Impact SRS Window Bags are designed to activate only in certain side collisions or in a roll over event. When the ORC (with side impact option) detects a collision or roll over requiring the window bags to inflate, it signals the inflators on the crash side of the vehicle. Both window bags will inflate in a roll over event. A quantity of nontoxic gas is generated to inflate the window bag.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The airbag light does not come on or flickers during the six to eight seconds when the ignition switch is first turned on. • The light remains on or flickers after the six to eight second interval. • The light flickers or comes on and remains on while driving. NOTE: If the speedometer, tachometer or any engine related gauges are not working, the airbag control module may also be disabled. The airbags may not be ready to inflate for your protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DaimlerChrysler Corporation, such investigations may be requested by customers, insurance carriers, government officials, and professional crash researchers, such as those associated with universities, and with hospital and insurance organizations.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Airbag disable lamp status (if equipped) • 9Time9 of airbag deployment (in terms of ignition cycles and vehicle mileage) • Airbag deployment level (if applicable) • Impact acceleration and angle • Seat belt status • Brake status (service and parking brakes) • Accelerator status (including vehicle speed) Child Restraint Everyone in your vehicle needs to be buckled up all the time - babies and children, too.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 babies at the right front passenger seat position. If a car bed must be used to transport a newborn baby, the car bed must be installed in the second seating row only. LATCH child restraint anchorage system. (Refer to “LATCH - Child Seat Anchorage System” in this section.) • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg).
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seatback, they should use a belt-positioning booster seat. The child and beltpositioning booster seat are held in the vehicle by the lap/shoulder belt. • Check belt fit periodically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips for getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. The manufacturer recommends that you try a child restraint in the vehicle seats where you will use it before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or collision, it could strike the occupants or seatbacks and cause serious personal injury. LATCH - Child Seat Anchorage System (Lower Anchors and Tether for CHildren) Your vehicle’s second row seat is equipped with the child restraint anchorage system called LATCH.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 only install the child restraints using the vehicle’s seat belts. Refer to “Installing the LATCH-Compatible Child Restraint System” this section. 2 Second Row Seat Right Side Second Row Seat Left Side Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE were provided with the child restraint system. The rear seat lower anchorages are round bars, located at the rear of the seat cushion where it meets the seatback, and are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE reach. If the buckled seat belt interferes with the child restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child. Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave an unattended child in the vehicle.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE pulling on the excess webbing to tighten the lap portion around the child restraint. Refer to 9Automatic Locking Mode9 in this section. Child Restraints in Third Row Seating (If Equipped) For vehicles equipped with third row split bench (60/40) seating, the tether strap anchorage is located on the seatback behind the center seating position. The hooks in the rear floor are NOT designed to withstand the forces that may occur during a crash.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Child Restraint Tether Anchor There are tether strap anchorages behind each seating position in the second row and behind the center seating position in the case of the third row seat (60/40) split bench, if equipped. To install child restraint tether follow these instructions: 2 1. Place the child restraint in the center seating position of the third row of seats. Third Row Seat Tether Anchor 2.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Follow the instructions for Child Restraint Tether Anchor in this section.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This is a normal part of the break-in and is not an indication of difficulty. 75 SAFETY TIPS Exhaust System WARNING! Exhaust gases contain carbon monoxide, an extremely toxic gas that by itself is colorless and odorless.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Be aware of changes in the sound of the exhaust system, exhaust fumes detected inside the vehicle, or damage to the underside or rear of the vehicle. Have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Safety Checks You Should Make Outside The Vehicle Door Latches Check for positive closing, latching and locking. Tires Examine tires for tread wear or uneven wear patterns. Check for stones, nails, glass or other objects lodged in the tread. Fluid Leaks Check area under vehicle after overnight parking for fuel, water, oil, or other fluid leaks. Also, if fuel fumes are detected, the cause should be located and corrected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS m Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .84 ▫ Automatic Dimming Mirror — If Equipped . . . .84 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .85 ▫ Exterior Mirrors Folding Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .85 ▫ Electric Remote-Control Mirrors . . . . . . . . . . . .86 ▫ Illuminated Vanity Mirrors — If Equipped .
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ General Information . . . . . . . . . . . . . . . . . . . 115 m Voice Recognition System (VR) — If Equipped . . 115 ▫ Voice Recognition System (VR) Operation . . . . 115 ▫ Commands . . . . . . . . . . . . . . . . . . . . . . . . . . 116 ▫ Voice Training . . . . . . . . . . . . . . . . . . . . . . . . 119 ▫ 4-Way Passenger’s Power Seat — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 124 ▫ Heated Seats — If Equipped . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 ▫ Self-Limiting Control . . . . . . . . . . . . . . . . . . . 141 ▫ Multifunction Control Lever . . . . . . . . . . . . . . 149 ▫ Driver Easy Exit And Easy Entry Control . . . . 141 m Windshield Wipers And Washers . . . . . . . . . . . . 151 m To Open And Close The Hood . . . . . . . . . . . . . 142 ▫ Windshield Wipers . . . . . . . . . . . . . . . . . . . . 151 m Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ To Accelerate For Passing . . . . . . . . . . . . . . . 159 ▫ Using HomeLinkt . . . . . . . . . . . . . . . . . . . . . 181 m Rear Park Assist System — If Equipped . . . . . . . 160 ▫ Reprogramming A Single HomeLinkt Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 m Rear Camera — If Equipped . . . . . . . . . . . . . . . 163 m Overhead Console . . . . . . . . . . . . . . . . . . . . . . 165 ▫ Courtesy/Reading Lights . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 m Floor Console . . . . . . . . . . . . . . . . . . . . . . . . . 189 m Factory Installed Roof Luggage Rack . . . . . . . . . 192 ▫ Front Floor Console Features . . . . . . . . . . . . . 189 m Cargo Management System—If Equipped . . . . . . 194 ▫ Rear Floor Console Features – If Equipped . . .
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Annoying headlight glare can be reduced by moving the small control under the mirror to the NIGHT position (toward the rear of vehicle). The mirror should be adjusted while set in the DAY position (toward the windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Automatic Dimming Mirror Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electric Remote-Control Mirrors The controls for the power mirrors are located on the driver’s door trim panel. Mirror Directions Remote Control Mirrors Switch To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When finished adjusting the mirror, turn the control to the center position to prevent accidentally moving a mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 WARNING! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side mirror. Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on each sun visor.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE that the heating elements are ON. Turning OFF the rear window defroster or the ignition will deactivate the heated mirrors. Automatic Dimming Driver’s Exterior Mirror — If Equipped This mirror will automatically adjust for annoying light glare from vehicles behind you. This feature is controlled by the inside mirror and can be turned off by pressing the button at the base of the inside mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnectt allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The UConnectt phonebook enables you to store up to 32 names, with four numbers per name. Each language has a separate 32-name phonebook accessible only in that language. This system is driven through your Bluetootht “Hands-Free profile” cellular phone.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Profile) you may not be able to use any UConnectt features. Refer to your cellular service provider or the phone manufacturer for details. • Prior to giving a voice command, one must wait for the beep, which follows the 9Ready9 prompt or another prompt. The UConnectt system is fully integrated with the vehicle’s audio system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Command Tree Refer to “Voice Tree” in this section. Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say 9Help9 following the beep. The UConnectt system will play all the options at any prompt if you ask for help. To activate the UConnectt system from idle, simply press the PHONE button and follow the audible prompts for directions.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE enter into your cellular phone. You can enter any four-digit PIN number. You will not need to remember this PIN number after the initial pairing process. • For identification purposes, you will be prompted to give the UConnectt system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between 1 and 7, with 1 being the highest priority.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 • The UConnectt system will confirm the phone number and then dial. The number will appear in the display of certain radios. • The UConnectt system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios. Call by Saying a Name Add Names to Your UConnectt Phonebook • Press the PHONE button to begin. NOTE: Adding names to the phonebook is recommended when the vehicle is not in motion.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, enter the number designation (e.g., 9Home,9 9Work,9 9Mobile,9 or 9Pager9). This will allow you to store multiple numbers for each phonebook entry, if desired. • When prompted, recite the phone number for the phonebook entry that you are adding. After you are finished adding an entry into the phonebook, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE the UConnectt system, and then send the address book entry via Bluetootht. Please see your phone owner’s manual for specific instructions on how to drop the Bluetootht connection. • If the phonebook entry is longer than 24 characters, it will only use the first 24 characters. Edit Entries in the UConnectt Phonebook NOTE: Editing names in the phonebook is recommended when the vehicle is not in motion. • Press the PHONE button to begin.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the 9Ready9 prompt and the following beep, say 9Phonebook Delete.9 • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say 9List Names9 to hear a list of the entries in the phonebook from which you choose.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnectt system will play the names of all the phonebook entries. • To call one of the names in the list, press the “Voice Recognition” button during the playing of the desired name, and say 9Call.9 NOTE: The user can also exercise 9Edit9 or 9Delete9 operations at this point. • The UConnectt system will then prompt you as to the number designation you wish to call. • The selected number will be dialed.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE call waiting that you normally hear when using your cell phone. Press the PHONE button to place the current call on hold and answer the incoming call. NOTE: The UConnectt system compatible phones in the market today do not support rejecting an incoming call when another call is in progress. Therefore, the user can only answer an incoming call or ignore it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Three-Way Calling To initiate three-way calling, press the “Voice Recognition” button while a call is in progress, and make a second phone call, as described under 9Making a Second Call While Current Call in Progress.9 After the second call has established, press and hold the PHONE button until you hear a double beep, indicating that the two calls have been joined into one conference call.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ignition key is switched to OFF, a call can continue on the UConnectt system for a certain duration, after which the call is automatically transferred from the UConnectt system to the mobile phone. • An active call is automatically transferred to the mobile phone after the ignition key is switched to OFF. UConnectT System Features Language Selection To change the language that the UConnectt system is using: • Press the PHONE button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the 9Ready9 prompt and the following beep, say 9Emergency9 and the UConnectt system will instruct the paired cellular phone to call the emergency number. This feature is only supported in the U.S. NOTE: The emergency number dialed is based on the country where the vehicle is purchased (911 for the U.S. and Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE certain companies, which time out a little too soon to work properly with the UConnectt system. Voice Mail Calling To learn how to access your voice mail, refer to 9Working with Automated Systems.9 Working with Automated Systems This method is used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated telephone system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • You may not hear all of the tones due to cellular phone network configurations; this is normal. • Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature. Barge In - Overriding Prompts The “Voice Recognition” button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE dialing a number with your paired Bluetootht cellular phone, the audio will be played through your vehicle’s audio system. The UConnectt system will work the same as if you dial the number using voice recognition. In order to un-mute the UConnectt system: NOTE: Certain brands of mobile phones do not send the dial ring to the UConnectt system to play it on the vehicle audio system, so you will not hear it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 If you would like to connect or disconnect the Bluetootht connection between a UConnectt paired cellular phone and the UConnectt system, follow the instructions described in your cellular phone User’s Manual. Select Another Cellular Phone This feature allows you to select and start using another phone paired with the UConnectt system.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete UConnectt Paired Cellular Phones • Press the PHONE button to begin. • After the 9Ready9 prompt and the following beep, say 9Setup Phone Pairing.9 • At the next prompt, say 9Delete9 and follow the prompts. • You can also press the “Voice Recognition” button at any time while the list is being played, and then choose the phone you wish to delete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE This procedure may be repeated with a new user. The system will adapt to the last trained voice only. • Performance is maximized under: To restore the voice recognition system to factory default settings, enter the Voice Training session via the above procedure and follow the prompts.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • It is not recommended to store similar sounding names in the UConnectt phonebook. • The UConnectt phonebook nametag recognition rate is optimized for the person who stored the name in the phonebook. • You can say 9O9 (letter 9O9) for 909 (zero). 98009 must be spoken 9eight-zero-zero.9 • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Bluetootht Communication Link Cellular phones have been found to lose connection to the UConnectt system. When this happens, the connection can generally be re-established by switching the phone off/on. Your cell phone is recommended to remain in Bluetootht ON mode. 109 Power-Up After switching the ignition key from OFF to either ON or ACC position, or after a language change, you must wait at least five seconds prior to using the system.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 3
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home 113 3
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call UConnectt Tutorial try again voice training work yes
UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you ever wish to interrupt the system while it lists options, press the VR hard-key, listen for the beep, and say your command. The system will best recognize your speech if the windows are closed, and the heater/air-conditioning fan is set to low. Pressing the VR hard-key while the system is speaking is known as “barging in.” The system will be interrupted and you can add or change commands. This will become helpful once you start to learn the options.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the voice recognition system is speaking. Please note the volume setting for VR is different then the audio system. • NEXT STATION (to select the next station) Main Menu Start a dialogue by pressing the VR hard-key. You may say MAIN MENU to switch to the main menu.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Satellite Radio To switch to satellite radio mode say SAT or SATELLITE RADIO.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE − CONTINUE (to continue recording) − DELETE (to delete the recording) • PLAY MEMOS (to play previously recorded memos) — During the playback you may press the VR hardkey to stop playing memos.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Front Seat Manual Seat Adjustment The adjusting lever is at the front of the seat, near the floor. Lift the lever and move the seat to the desired position. Release the bar to lock the seat into position. Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. Front Seat Manual Seat Recliners The bucket seats are equipped with recliners.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Lumbar Support Adjustment — If Equipped The manual lumbar support adjustment lever is located on the right side of the driver’s seat and on the left side of the passenger’s seat. Moving the lumbar control lever fore and aft increases or decreases the lumbar support. Adjustable Head Restraints — All Seating Positions Head restraints can reduce the risk of whiplash injury in the event of impact from the rear.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 8-Way Driver’s Power Seat — If Equipped The driver’s power seat switches are located on the left side of the driver’s seat lower side trim. The bottom switch controls up/down, forward/rearward, and tilt adjustment. The top switch controls the seatback recline adjustment.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4-Way Passenger’s Power Seat — If Equipped The front passenger’s power seat switches are located on the right side of the passenger seat lower side trim. The bottom switch controls forward/rearward adjustment. The top switch controls the seatback recline adjustment. NOTE: The 4-way seat does not have an up/down adjustment. Heated Seats — If Equipped This feature heats the driver, front passenger and second row seats.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 With the ignition switch in the RUN position, depressing the heated seat switch rocker to its momentary high or low position provides power to the heated seat element and maintains the requested temperature setting. If the heated seat switch is depressed to a different position (low or high) than the currently selected state, the requested temperature setting will change to a new selection.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE off. Both of the indicators on identifies High heat level. The lower indicator on only identifies Low heat level. NOTE: The HI heat setting will operate for approximately 30 minutes. After 30 minutes, the system will automatically transition to the low heat setting. The LO heat setting will operate for 30 minutes, then the system will turn off. If the low heat setting is initially selected, the system will operate for 30 minutes and then turn off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second Row Bucket Seats — Fold and Tumble Second row bucket seats have seatback recliners on both seating positions. Raising the lever allows the seatback to be reclined an additional 11 degrees. 127 3. Pull up on the seatback release lever located on the outboard side of the seat and push the seatback forward. The second row bucket seats can be folded and tumbled forward for easy access to the third seat or rear cargo area.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Pull up on the release handle and lift to tumble the seat fully forward. If the seat contacts the rear of the front seat, move the front seat forward. To relatch the seat, tilt the seat rearward and push down firmly to engage the rear attachments. Then lift the seatback release lever and pull the seatback up to return it to its full upright position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 WARNING! In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure the seats are fully latched. Tumble Lever Second Row 40/20/40 Seat — Fold and Tumble The 40/20/40 seat configuration is standard on all models. This seat is equipped with a unique fold-and-tumble feature. The 40% seatbacks have spring loaded hinges which assist with the folding of the seatbacks.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second row leather seats have seatback recliners at the 40% seating positions. Raising the lever allows the seatback to be reclined an additional 11 degrees. To fold the 40% seatbacks, fully raise the lever on the side of the seat to release the seatback. The seatback can now be folded into the down position for use as a cargo floor, or the seat can now be tumbled forward to allow access to the rear of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 To fold the 20% seatback, pull the strap forward to release the seatback. Fold the seatback down for use as an armrest or to carry cargo. When returning the seatback to the upright position, push the seatback rearward to latch the seatback. Pull the seatback forward to ensure that it is locked in the upright position. 3 WARNING! The 20% seatback contains the center shoulder belt.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not drive the vehicle with the outer 40% second row seats in the tumbled position. The outer 40% second row seats are only intended to be tumbled for entry and exit to the third row seat. Failure to follow these instructions could result in personal injury. NOTE: The seatback must be fully folded into the down position to allow the lever to be raised enough to release the floor latches.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Third Row Seat Bench — If Equipped To Fold the Seats Folding the third seat occurs in two stages: First, the cushion is lifted and moved forward from the pockets at the front of the cushion. The cushion will rest on the floor directly behind the second row seat. Second, the top of the back is folded forward and rests on the cushion. The back will not fold unless the cushion has been folded forward first.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Seat Cushion Movement Up And Forward Third Row Seat Folded Forward CAUTION! When loading cargo into the rear of your vehicle with the third row seat folded flat, be careful not to damage the material on the head restraints.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The seat belt buckles are hinged to fold with the seatback. 135 Third Row 60/40 Folding — If Equipped WARNING! 3 Do not sit in the third row seat unless the cushion and back are properly engaged. Proper engagement can be verified by pushing/pulling on the upright seatback. The seatback will not move unless properly engaged. Do not sit in the 3rd row seat with the second row seatback(s) folded or tumbled.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Third Row Seat 40% Seatback Fold Third Row Seat Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 3 Third Row Seat Folded Forward Third Row Seat Return Pull Strap DRIVER MEMORY SYSTEM — IF EQUIPPED Once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat position, driver’s outside mirror position, adjustable brake and accelerator pedals position, Automatic Temperature Control (ATC) temperature and radio station
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE preset settings. Your Remote Keyless Entry (RKE) Transmitters can also be programmed to recall the same positions when the UNLOCK button is pressed. position. The memory system can accommodate up to two transmitters, each transmitter linked to either of the two memory positions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Turn on the radio and set the radio station presets (up to 10 AM and 10 FM stations can be set). 4. Adjust the Automatic Temperature Control (ATC) while the ATC is in Auto mode. 5. Press and release the SET (S) button located on the driver’s door. 6. Within five seconds, press and release memory button 1 or 2 on the driver’s door. The next step must be performed within 10 seconds if you desire to also use a RKE Transmitter to recall memory positions. 7.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To recall the memory settings for driver one, press memory button number 1 on the driver’s door or the UNLOCK button on the Remote Keyless Entry Transmitter linked to memory position 1. To recall the memory setting for driver two, press memory button number 2 on the driver’s door or the UNLOCK button on the Remote Keyless Entry transmitter linked to memory position 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE with the Electronic vehicle Information Center (EVIC), refer to “Personal Settings (Customer Programmable Features)” under “Overhead Console with Electronic Vehicle Information Center (EVIC) – If Equipped” in Section 3. Self-Limiting Control To improve vehicle reliability, the memory system includes a self-limiting control for full travel positioning of power seat and adjustable pedal movement (all directions).
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the Electronic Vehicle Information Center (EVIC). For details, refer to “Personal Settings (Customer Programmable Features)” under “Overhead Console with Electronic Vehicle Information Center (EVIC) – If Equipped” in Section 3. TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then push the safety latch lever to the left. It is located between the grille and hood opening right of the center. 143 To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center front edge of the hood to ensure that both latches engage. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Headlight Switch Headlight Switch Location
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 and the interior lights are on, rotating the dimmer control all of the way down to the OFF detent will cause all the interior lights to go out. This allows the doors to stay open for extended periods of time without discharging the vehicle’s battery.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the ignition is off and any door is left ajar for eight minutes or the dimmer control is rotated upwards for 15 minutes, the interior lights will automatically turn off. If the headlights remain on while the ignition is cycled off, the exterior lights will automatically turn off after eight minutes. If the headlights are turned on and left on for eight minutes while the ignition is off, the exterior lights will automatically turn off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Headlights — If Equipped Automatic headlights can be activated by rotating the rotary headlight switch to the symbol “A.” The headlights will turn on when the engine is running and the ambient light sensor indicates that the headlights should be activated. The headlights will turn off if the headlight switch is rotated to the OFF position or 90 seconds after the ignition is turned to OFF.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights (Canada Only) The headlights on your vehicle will illuminate when the engine is started. This provides a constant “Lights ON” condition until the ignition is turned OFF. The lights illuminate at reduced intensity. If the parking brake is applied the Daytime Running Lights (DRLs) will turn off. If the headlights are activated, the DRL feature will transition to the normal headlight operating mode.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 light located in the instrument cluster will illuminate when the fog lights are on. The fog lights will turn off when the switch is pressed in, when the headlight switch is rotated to the OFF position, or the high beam is selected. The arrow on either side of the instrument cluster flashes to indicate the direction of the turn, and proper operation of the front and rear turn signal lights.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If a turn signal has been left on for at least a mile (a kilometer), a continuous chime will sound. Turn Signal Auto-Mode Tap the multifunction control lever once and the turn signal (left or right) will flash three times, and automatically turn off. Passing Light You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steering wheel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE High Beam/Low Beam Select Switch Pull the multifunction control lever fully toward the steering wheel to switch the headlights from high or low beam. 151 WINDSHIELD WIPERS AND WASHERS Windshield Wipers 3 Windshield Wiper Switch Dimmer Lever The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range. The delay interval decreases as you rotate the knob until it enters the low continual speed position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Windshield Washers To use the washer, push in on the washer knob on the end of the multifunction control lever and hold while spray is desired. If the washer knob is depressed while in the delay range, the wiper will operate for several seconds after the washer knob is released. It will then resume the intermittent interval previously selected.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, pull rearward on the lever below the turn signal control and move the wheel up or down, as desired. Push the lever forward to lock the column firmly in place. Tilt Steering Column Lever WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER ADJUSTABLE PEDALS — IF EQUIPPED 155 Adjustment 1. Position the driver seat so that you are at least 10 in (254 mm) away from the airbag located in the center of the steering wheel. 2. Fasten and adjust the seatbelts. 3. Move the adjustable pedal switch, located to the left of the steering column near the parking brake release, up to move the pedals toward the driver or down to move the pedals away from the driver. 4.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over accelerator operation at speeds greater than (refer to the following table for the speed for your specific engine).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE can be reactivated by pushing the speed control switch ON/OFF button and re-establishing the desired vehicle SET speed. Push the ON/OFF button to the ON position. In the instrument cluster, the word “CRUISE” illuminates when the system is on. To Set At A Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Vary The Speed Setting When the speed control is on, speed can be increased by pressing and holding the RESUME/ACCEL button. When the button is released, a new set speed will be established. Tapping the RESUME/ACCEL button once will result in a speed increase (refer to the table below for the speed for your specific engine). Each time the button is tapped, speed increases, so tapping the button three times will increase speed by three increments.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: When driving uphill, at elevations above 2,000 ft (610 m), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed. If the vehicle speed drops below (refer to the previous table for the speed for your specific engine), the speed control will automatically disengage.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR PARK ASSIST SYSTEM — IF EQUIPPED NOTE: The manufacturer suggests disabling the Rear Park Assist System when towing a trailer. Refer to “Personal Settings (Customer Programmable Features)” under “Overhead Console with Electronic Vehicle Information Center (EVIC) – If Equipped” in Section 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 The system dimly illuminates the two outermost yellow LEDs when it is ON and detecting no obstacles. The following chart shows the warning display operation when the system is detecting an obstacle: WARNING DISPLAY DISTANCES DISPLAY LED 1st LED 2nd LED 3rd LED 4th LED 5th LED 6th LED 7th LED 8th LED OBSTACLE DISTANCE FROM: REAR CORNERS REAR CENTER 78.7 in (200 cm) 51.1 in (130 cm) 45.2 in (115 cm) 31.5 in (80 cm) 39.3 in (100 cm) 25.5 in (65 cm) 33.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Drivers must be careful when backing up, even when using the Rear Park Assist System. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • Ensure that the rear bumper is free of dirt and debris to keep the system operating properly. • Jackhammers, large trucks, and other vibrations could affect the performance of the system. If “Service Park Assist System” appears in the Electronic Vehicle Information Center (EVIC) after making sure the rear bumper is clean, please see your authorized dealer.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The camera view will display only while the vehicle is in REVERSE. 4. Perform a visual check of the rear area. NOTE: CHECK ENTIRE SURROUNDINGS before backing up. 5. Slowly backup as necessary. 6. Place the shift lever in PARK or DRIVE to exit the Rear Backup Camera system. WARNING! Drivers must be careful when backing up even when using the Rear Camera System.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! OVERHEAD CONSOLE The overhead console has the following features: • To avoid vehicle damage, the Rear Camera System should only be used as a parking aid and is unable to view every obstacle or object in your drive path. 3 • To avoid vehicle damage, the vehicle must be driven slowly when using the Rear Camera System to be able to stop in time when an obstacle is seen.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Electronic Vehicle Information Center (EVIC) — If Equipped Courtesy/Reading Lights Near the front of the console is one courtesy and two reading lights. All lights illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (fully upward position), or when the UNLOCK button is pressed on the Remote Keyless Entry (RKE) Transmitter, if so equipped.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electronic Vehicle Information Center (EVIC) — If Equipped 167 Trip Functions Pressing the STEP button allows you to scroll through one of the following Trip Function features: • TRIP – Shows the total distance traveled since the last reset. To reset the TRIP function, press and hold the RESET button. • ELAPSED TIME – Shows the total elapsed time of travel since the last reset.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE before the reset. (Example: If your EVIC displays 18 AVG. MPG and the RESET button is pressed, the previous averaging history will be erased and the display will return to the 18 AVG. MPG, not to 0 AVG. MPG). The display may take several miles/kilometers for the value to change, depending upon driving habits. If equipped with a 5.7L engine and Multi Displacement System (MDS), FUEL SAVER may be displayed along with the actual AVG. MPG.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • TURN SIGNALS ON (with a continuous warning chime) • PERSONAL SETTINGS NOT AVAILABLE – Vehicle not in PARK • LEFT/RIGHT FRONT DOOR AJAR (one or more, with a single chime if speed is above 1 mph/1 km/h) • LEFT/RIGHT REAR DOOR AJAR (one or more, with a single chime if speed is above 1 mph/1 km/h) • DOOR(S) AJAR (with a single chime if vehicle is in motion) • LOW WASHER FLUID (with a single chime) • OIL CHANGE REQUIRED (with a single chime) • SERVICE PARK ASSIST SYS
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Turn the ignition switch to the ON position (Do not start the engine). 2. Fully depress the accelerator pedal slowly three times within 10 seconds. 3. Turn the ignition switch to the OFF/LOCK position. NOTE: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE stopped and the transmission is in the PARK or NEUTRAL position and the driver’s door is opened. To make your selection, press and release the RESET button until “ON” or “OFF” appears. • “RKE UNLOCK DRV DR 1st” – When DRV DR 1st is selected, only the driver’s door will unlock on the first press of the RKE UNLOCK button. When Driver Door 1st Press is selected, you must press the Remote Keyless Entry UNLOCK button twice to unlock the passenger’s doors.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “HEADLAMP OFF DELAY > 0 SEC” – When this feature is selected, the driver can choose to have the headlamps remain on for 0, 30, 60, or 90 seconds when exiting the vehicle. To make your selection, press and release the RESET button until “0,” “30,” “60,” or “90” appears. NOTE: The headlamp switch must be in the “A” auto mode before this feature will work.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 • “UNIT IN > U.S./METRIC” – The EVIC odometer can be changed between English and Metric units of measure. To make your selection, press and release the RESET button until “US” or “METRIC” appears. Compass/Temperature Button Pressing the Compass/Temperature button will return the display to the normal compass/ temperature display. • “COMPASS VARIANCE > 8” – Press the RESET button to change the compass variance setting. Set this to your current location.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Compass Calibration If the compass appears erratic and the “CAL” message does not appear in the EVIC display, you must put the compass into the Calibration Mode manually as follows: 5. Slowly drive the vehicle at a speed of 5 mph (8 km/h) in a complete 360°circle, (in an area free from large metal or metallic objects) until the “CAL” message turns off. The compass will now function normally. 1. Turn the ignition switch to the ON/RUN position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 1. Turn the ignition switch to the ON/RUN position. 2. Press the MENU button until “Personal Settings” is displayed. 3. Press the STEP button until “Compass Variance” is displayed. 4. Press and release RESET button until the proper variance zone is selected according to the variance map. 5. Press and release the Compass/Temperature button to exit.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED HomeLinkt replaces up to three remote controls (handheld transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLinkt unit operates off your vehicle’s battery. The HomeLinkt buttons are located in the overhead console, and contain one, two, or three dots/lines designating the different HomeLinkt channels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 WARNING! WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE It is recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLinkt for more efficient training and accurate transmission of the radio-frequency signal. Your vehicle should be parked outside of the garage while training. Then release both the HomeLinkt and hand-held transmitter buttons. If the EVIC display states “DID NOT TRAIN” repeat Step 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 NOTE: After training a HomeLinkt channel, if the garage door does not operate with HomeLinkt and the garage door opener was manufactured after 1995, the garage door opener may have rolling code. If so, proceed to the heading “Programming A Rolling Code System.” 3 5. PROGRAMMING A ROLLING CODE SYSTEM At the garage door opener motor (in the garage), locate the “learn” or “training” button.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Return to the vehicle and press the programmed HomeLinkt button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for two seconds) to complete the training. If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLinkT To operate, simply press and release the programmed HomeLinkt button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.) The hand-held transmitter of the device may also be used at any time. Reprogramming A Single HomeLinkT Button To reprogram a channel that has been previously trained, follow these steps: 1.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Did you unplug the device for training, and remember to plug it back in? If you are having any problems or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interference 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE the panel is venting, pressing the “close” end of the rocker switch returns it to the closed position. Both opening and closing operations in the vent mode occur only while the switch is held. NOTE: The sunroof will continue to operate for 10 minutes after the ignition is turned OFF or until the driver’s door is opened. This feature may be disabled by your authorized dealer.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. Do not allow small children to operate the sunroof. Never allow fingers or other body parts, or any object to project through the sunroof opening. Injury may result.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS This vehicle has three auxiliary power outlets that can provide up to 20 Amps of current for accessories designed for use with the standard power outlet adapters. The outlet located in the lower portion of the instrument panel has a snap on plastic cap so that it can be covered when not in use. As a safety precaution, the outlet in the instrument panel only operates with the ignition switch ON.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: When the inverter switch is pressed, there will be a delay of approximately one second before the inverter status indicator turns ON. The status Indicator of the AC power inverter indicates whether the inverter is producing AC power. NOTE: Due to build-in overload protection the inverter will shut down if the power rating is exceeded. WARNING! To avoid serious injury or death: • Do not use a 3-prong adapter.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Electrical Outlet Use With Engine OFF (Battery Fed Configuration) CAUTION! 115V Inverter Plug • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reconfiguring Power Outlets To reconfigure the outlets, be sure the ignition is OFF before removing the fuse. The reconfigurable fuse location is a special design that allows the fuse to be installed in two different ways. If the fuse is located in the 9Upper or Top Position9 the outlets will work at all times. If the fuse is located in the 9Lower or Bottom Position9 the power outlets will only work when the ignition is ON.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 FLOOR CONSOLE • Removable CD bin Front Floor Console Features The floor console between the driver’s and front passenger’s seat, has the following features: • 115 V Inverter Plug • Miscellaneous storage compartments The coin slots are located under the instrument panel center stack. • Portable phone storage bin • Portable phone cord routing on the sides of the console lid and the base.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In colder temperatures you may experience a slight delay on console doors opening; the console door speed will come back to normal after 1–2 cycles. Front Center Console Cupholder Doors The front storage bin in the center console is equipped with a removable bin mat. This mat can be removed by pulling on the tab located on the front edge of the bin mat. Removing this mat will allow you to retrieve any lost items that are between the bin doors.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 being stored in the bin. To use, plug in the portable power recharge cord and place the cord along the opening under the forward portion of the storage bin. Close the console armrest lid and plug the power cord into the phone while resting the phone in the bin. The power outlet may be used for any portable item with a standard 12 Volt power outlet adapter, requiring up to 20 Amps of current.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Tissue holder and pen holder FACTORY INSTALLED ROOF LUGGAGE RACK • Second row heated seat switches • Four slots for DVDs Roof Luggage Rack Rear Floor Console To access the storage bin, lift up on the console door latch. The load carried on the roof when equipped with a luggage rack must not exceed 150 lbs (68 kg), and should be uniformly distributed over the cargo area.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The side rails between the stantions should be used to tie down cargo. Check the straps frequently to be sure that the load remains securely attached. NOTE: Crossbars are offered by Mopart accessories. External racks do not increase the total load carrying capacity of the vehicle. Be sure that the total occupant and luggage load inside the vehicle, plus the load on the luggage rack, do not exceed the maximum vehicle load capacity.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Cargo must be securely tied down before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof rack Cautions when carrying cargo on your roof rack. CARGO MANAGEMENT SYSTEM—IF EQUIPPED The cargo management system consists of a removable cargo liner and removable cargo organizer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 3 Side Cover To open the main cover, pull up on the latch, and attach the cord to the rear seat head restraint post. To open the cargo divider, lift up on the cargo divider handles, raising the doors to the full open position. Raise the side panels until they engage into the doors.
INSTRUMENT PANEL AND CONTROLS CONTENTS m Instruments And Controls . . . . . . . . . . . . . . . . . 201 ▫ Electrical Disturbances . . . . . . . . . . . . . . . . . . 216 m Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 202 ▫ AM Reception . . . . . . . . . . . . . . . . . . . . . . . 216 m Instrument Cluster Description . . . . . . . . . . . . . 203 ▫ FM Reception . . . . . . . . . . . . . . . . . . . . . . . . 216 m Electronic Digital Clock . . . . . . . . . . . . . . . . . .
198 INSTRUMENT PANEL AND CONTROLS ▫ Operating Instructions — Hands-Free Communication (UConnectt) (If Equipped) . . . 218 ▫ Clock Setting Procedure . . . . . . . . . . . . . . . . . 218 m Sales Code RER — Multimedia System — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 ▫ Operating Instructions — Satellite Radio . . . . . 221 ▫ Operating Instructions — Hands-Free Communication (UConnectt) (If Equipped) . . . 221 ▫ Clock Setting Procedure . . . . . . . . . . . . . . . . .
INSTRUMENT PANEL AND CONTROLS 199 ▫ Operating Instructions - Video Entertainment System (VES™) (If Equipped) . . . . . . . . . . . . . 241 ▫ Left-Hand Switch Functions For Media (i.e., CD) Operation . . . . . . . . . . . . . . . . . . . . 247 m Universal Consumer Interface (UCI) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 241 m Compact Disc Maintenance . . . . . . . . . . . . . . . . 247 ▫ Connecting The iPodt Device . . . . . . . . . . . .
200 INSTRUMENT PANEL AND CONTROLS ▫ Automatic Control . . . . . . . . . . . . . . . . . . . . 254 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . . 261 ▫ Level Of Automatic Control . . . . . . . . . . . . . . 255 ▫ Operating Tips Chart . . . . . . . . . . . . . . . . . . . 263 ▫ Manual Control (ATC) . . . . . . . . . . . . . . . . . . 256 m Rear Window Features . . . . . . . . . . . . . . . . . . . 264 ▫ Rear Zone Climate Control — If Equipped . . . 259 ▫ Rear Window Wiper/Washer . . .
INSTRUMENT PANEL AND CONTROLS 201 INSTRUMENTS AND CONTROLS 4
202 INSTRUMENT PANEL AND CONTROLS Instrument Cluster
INSTRUMENT PANEL AND CONTROLS INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gage The fuel gage shows level of fuel in the tank when ignition switch is in the ON position. 2. Temperature Gage The temperature gage indicates engine coolant temperature. Any reading within the normal range indicates that the cooling system is operating satisfactorily. The gage needle in V6 and V8 engines will likely indicate a high temperature when driving in hot weather, up mountain grades, in heavy traffic, or when towing a trailer.
204 INSTRUMENT PANEL AND CONTROLS left/right turn signal is left on with the engine RPM vehicle speed greater than 15 mph (24 km/h) for more than one mile. 4. Low Fuel Warning Light This indicator lights when the fuel gage reads 1/16 of a tank or less. 5. High Beam Indicator Indicates that headlights are on high beam. 6. Seat Belt Reminder Light This light comes on for several seconds after the ignition is turned ON as a reminder to “buckle up.
INSTRUMENT PANEL AND CONTROLS WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, refer to “Cooling System Pressure Cap” under “Cooling System” in Section 7. Follow the warnings under the paragraph. 8. Speedometer The speedometer shows the speed of the vehicle. 9. Voltage Light This light monitors the electrical system voltage.
206 INSTRUMENT PANEL AND CONTROLS charging voltage falls below 10 volts, the malfunction indicator light illuminates and the ABS is switched off. When the voltage is above this value again, the malfunction indicator light should go out and the ABS is operational. If the malfunction indicator light stays illuminated, have the system checked at your authorized dealer as soon as possible. 12. Engine Oil Pressure Indicator Light This light indicates that the engine oil pressure has become too low.
INSTRUMENT PANEL AND CONTROLS The two trip odometers show individual trip mileage. To switch from odometer to trip odometers, press and release the Trip Odometer button. To reset a trip odometer, display the desired trip odometer to be reset then push and hold the button until the display resets (approximately two seconds).
208 INSTRUMENT PANEL AND CONTROLS Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and release the Trip Odometer button on the instrument cluster. To reset the oil change indicator system (after performing the scheduled maintenance) refer to the following procedure. 1. Turn the ignition switch to the ON position (Do not start the engine). 2.
INSTRUMENT PANEL AND CONTROLS ESP/TCS indicator light starts to flash as soon as the tires lose traction and the ESP system becomes active. The ESP/TCS indicator light also flashes when TCS is active. If the ESP/TCS indicator light begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions.
210 INSTRUMENT PANEL AND CONTROLS have the bulb repaired promptly. If the light stays on, it may be an indication that the parking brake has not been released, or there is a low brake fluid level. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or a problem with the Brake Booster.
INSTRUMENT PANEL AND CONTROLS 23. Malfunction Indicator Light (MIL) This light is part of an onboard diagnostic system which monitors the emissions and engine control system. If the vehicle is ready for emissions testing, the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started.
212 INSTRUMENT PANEL AND CONTROLS by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
INSTRUMENT PANEL AND CONTROLS tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style.
214 INSTRUMENT PANEL AND CONTROLS 28. Cruise Light (Speed Control) This indicator lights when the electronic speed control system is turned on. 29. TOW/HAUL The TOW/HAUL button is located at the end of the gear shift lever. This light will illuminate when the TOW/ HAUL button has been selected. 30. 4LOW Indicator Indicates transfer case is in 4LOW position. 31. Odometer/Trip Odometer Button Press this button to toggle between the odometer and the trip odometer display.
INSTRUMENT PANEL AND CONTROLS Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the right side TUNE/ AUDIO control knob. 215 SETTING THE ANALOG CLOCK To set the analog clock at the top center of the instrument panel, press and hold the button until the setting is correct. 3. After the hours are adjusted, push the right side TUNE/AUDIO control knob to set the minutes. 4 4.
216 INSTRUMENT PANEL AND CONTROLS RADIO GENERAL INFORMATION Radio Broadcast Signals The radio will provide excellent reception under most operating conditions. Like any system, however, vehicle radios have performance limitations, due to mobile operation and natural phenomena, which might lead you to believe your sound system is malfunctioning.
INSTRUMENT PANEL AND CONTROLS NOTE: The radio, steering wheel radio controls (if equipped), and 6–Disc CD/DVD changer (if equipped) will remain active for up to 10 minutes after the ignition switch has been turned OFF. Opening a vehicle front door will cancel this feature. SALES CODE REN — MULTIMEDIA SYSTEM — IF EQUIPPED NOTE: The sales code is located on the lower right side of the unit’s faceplate.
218 INSTRUMENT PANEL AND CONTROLS Operating Instructions — Satellite Radio (If Equipped) Refer to your Radio-specific user’s manual for detailed operating instructions. Clock Setting Procedure Operating Instructions — Voice Recognition System (VR) (If Equipped) For the radio, refer to “Voice Recognition System (VR)” in Section 3. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen.
INSTRUMENT PANEL AND CONTROLS 5. To save the new time setting, touch the screen where the word “Save” is displayed. Changing Daylight Savings Time When selected, this feature will display the time of day in daylight savings time. Proceed as follows to change the current setting: 1. Turn on the multimedia system. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3.
220 INSTRUMENT PANEL AND CONTROLS 3. Touch the screen where the words “Set Time Zone” are displayed. The time zone selection menu will appear on the screen. NOTE: If your vehicle is not equipped with UConnectt, the unit will respond with a “Feature Not Available” message when selecting controls related to this feature. 4. Select a time zone by touching the screen where your selection appears.
INSTRUMENT PANEL AND CONTROLS An auxiliary input jack permits passengers to listen to a portable MP3 player through the vehicle’s speakers. For vehicles equipped with the Vehicle Entertainment System (VES)t, separate audio outputs allow passengers to listen to the vehicle speakers while different audio tracks play through the system’s wireless headphones.
222 INSTRUMENT PANEL AND CONTROLS 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. If the words “Time: GPS Time” are displayed at the top of the screen, proceed to Step 4. Otherwise, proceed to Step 3. Changing Daylight Savings Time When selected, this feature will display the time of day in daylight savings time. Proceed as follows to change the current setting: 3.
INSTRUMENT PANEL AND CONTROLS 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. If the words “Time: User Clock” are displayed at the top of the screen, proceed to Step 4. Otherwise, proceed to Step 3. 3. If the words “Time: GPS Time” are displayed at the top of the screen, touch the bottom of the screen where the words “GPS Time” are displayed. The user clock time setting menu will appear on the screen. 4.
224 INSTRUMENT PANEL AND CONTROLS SALES CODE RES — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
INSTRUMENT PANEL AND CONTROLS to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. SCAN Button Pressing the SCAN button causes the tuner to search for the next listenable station in AM or FM frequencies, pausing for five seconds at each listenable station before continuing to the next. To stop the search, press the SCAN button a second time.
226 INSTRUMENT PANEL AND CONTROLS Clock Setting Procedure 1. Press and hold the TIME button, until the hours blink. 2. Adjust the hours by turning the right side TUNE/ SCROLL control knob. 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save time change. 5. To exit, press any button/knob or wait five seconds.
INSTRUMENT PANEL AND CONTROLS 227 Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the bass tones. Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary TUNE/SCROLL control knob a second time and MID will display.
228 INSTRUMENT PANEL AND CONTROLS Toggle the MUSIC TYPE button to select the following format types: Program Type No program type or undefined Adult Hits Classical Classic Rock College Country Foreign Language Information Jazz News Nostalgia Oldies 16-Digit Character Display None Adlt Hit Classicl Cls Rock College Country Language Inform Jazz News Nostalga Oldies Program Type Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 W
INSTRUMENT PANEL AND CONTROLS By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode. If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be exited and the radio will tune to the preset station.
230 INSTRUMENT PANEL AND CONTROLS Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 These buttons tune the radio to the stations that you commit to pushbutton memory (12 AM and 12 FM stations). DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes. Operation Instructions - CD MODE for CD and MP3 Audio Play NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
INSTRUMENT PANEL AND CONTROLS CAUTION! • This CD player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • RES is a single CD player. Do not attempt to insert a second CD if one is already loaded. • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player.
232 INSTRUMENT PANEL AND CONTROLS TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display. RW/FF Press the RW button to stop the CD at the beginning of the current CD track/title. Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner. Press the right SEEK button to move to the next randomly selected track.
INSTRUMENT PANEL AND CONTROLS files properly and may be unable to play the file normally. UDF and Apple HFS formats are not supported. The radio uses the following limits for file systems: • Maximum number of folder levels: 8 • Maximum number of files: 255 • Maximum number of folders. (The radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name and will assign a number instead.
234 INSTRUMENT PANEL AND CONTROLS rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates. MPEG Specification Sampling Frequency (kHz) MPEG-1 Audio Layer 3 48, 44.1, 32 MPEG-2 Audio Layer 3 24, 22.
INSTRUMENT PANEL AND CONTROLS LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob. Selecting a folder by pressing the TUNE/SCROLL control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain playable files). The folder list will time out after five seconds.
236 INSTRUMENT PANEL AND CONTROLS TIME Button (Auxiliary Mode) Press this button to change the display to time of day. The time of day will display for five seconds (when ignition is OFF). Operating Instructions - Hands-Free Phone (UConnectt) (If Equipped) Refer to “Hands-Free Communication (UConnectt)” in Section 3. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to “Satellite Radio” in this section.
INSTRUMENT PANEL AND CONTROLS 237 call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com, or at www.siriuscanada.ca for Canadian residents. Please have the following information available when calling: selected. Press the TUNE/SCROLL control knob and the Sirius ID number will display. The Sirius ID number display will time out in two minutes. Press any button on the radio to exit this screen. 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID).
238 INSTRUMENT PANEL AND CONTROLS Satellite Antenna To ensure optimum reception, do not place items on the roof around the rooftop antenna location or strap items to the trunk lid around the trunk lid antenna (if equipped). Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items such as bikes should be placed as far rearward as possible, within the loading design of the rack. Do not place items directly on or above the antenna.
INSTRUMENT PANEL AND CONTROLS SCAN Button Pressing the SCAN button causes the tuner to search for the next channel, pausing for eight seconds before continuing to the next. To stop the search, press the SCAN button a second time. INFO Button Pressing the INFO button will cycle between Artist, Song Title, and Composer (if available) information.
240 INSTRUMENT PANEL AND CONTROLS SETUP Button Pressing the SETUP button allows you to select the following items: • Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number. This number is used to activate, deactivate, or change the Sirius subscription. SET Button – To Set the Pushbutton Memory When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window.
INSTRUMENT PANEL AND CONTROLS Operating Instructions - Hands-Free Phone (If Equipped) Refer to “Hands-Free Communication (UConnectt)” in Section 3. Operating Instructions - Video Entertainment System (VES™) (If Equipped) Refer to separate “Video Entertainment System (VES™) Guide.” UNIVERSAL CONSUMER INTERFACE (UCI) — IF EQUIPPED NOTE: This section is for sales code RES and REQ radios only with UConnectt. For sales code REN touch screen radio, refer to the separate User’s Manual.
242 INSTRUMENT PANEL AND CONTROLS Connecting The iPodT Device Use the optional connection cable to connect an iPodt to the vehicle’s UCI connector (which is located in the glove box on some vehicles. This location may vary with vehicle). Once the iPodt is connected and synchronized to the vehicle system (this may take a few seconds to connect), the vehicle brand logo appears on the iPodt display, and it starts charging and is ready for use by pressing radio switches as described below.
INSTRUMENT PANEL AND CONTROLS RW (Rewind) Button Press and hold the RW button to move backward in the current track. Holding the RW button long enough will take you back to the beginning of the current track. Pressing and releasing the RW button will go back five seconds of the current track. FF (Fast Forward) Button Press and hold the FF button to move forward in the current track. Pressing and releasing the FF button will go forward five seconds of the current track.
244 INSTRUMENT PANEL AND CONTROLS SCAN Button Pressing the SCAN button will play the first five seconds of each track in the current list and then forward to the next song. To stop the SCAN mode and start playing the desired track, press the SCAN button again. During the SCAN mode, you can also press the SEEK button to the left or right to go to the previous or next tracks. RND (Random) Button (RES Radios Only) Pressing the RND button will switch between the shuffle on and shuffle off modes of the iPodt.
INSTRUMENT PANEL AND CONTROLS Radio Preset Buttons In the List mode, the radio preset buttons are used as shortcuts to the following lists on the iPodt device. • 1 – Playlists • 2 – Artists • 3 – Albums • 4 – Genres • 5 - Audiobooks • 6 – Podcasts After pressing a preset button, you will see the list you are in on the top line and the first item in that list on the second line. To exit the List mode without selecting a track, press the same preset button again to go back to Play mode.
246 INSTRUMENT PANEL AND CONTROLS VIDEO ENTERTAINMENT SYSTEM (SALES CODE XRV) — IF EQUIPPED The optional Video Entertainment System™ (VES™) consists of a DVD player and LCD (liquid crystal display) screen, a battery-powered remote control, and two headsets. The system is located in the headliner behind the front row seat. Refer to your VES™ User’s Manual for detailed operating instructions.
INSTRUMENT PANEL AND CONTROLS Left-Hand Switch Functions for Radio Operation • Press the top of the switch to SEEK the next listenable station up from the current setting. • Press the bottom of the switch to SEEK the next listenable station down from the current setting. • Press the button in the center of the switch to tune to the next preset that you have programmed. Left-Hand Switch Functions for Media (i.e., CD) Operation • Press the top of the switch once to listen to the next track.
248 INSTRUMENT PANEL AND CONTROLS 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. NOTE: If you experience difficulty in playing a particular disc, it may be damaged (i.e. scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have theft protection encoding. Try a known good disc before considering disc player service.
INSTRUMENT PANEL AND CONTROLS CLIMATE CONTROLS Manual Control 249 Air Conditioning Operation To turn the air conditioning ON or OFF, perform the following steps: • Position the mode control button to the desired airflow setting. • Set the front blower control to any desired speed. • Press the Snowflake (A/C) button which is located to the right of the temperature control slide. An indicator light on the Snowflake (A/C) button shows that the air conditioning is ON.
250 INSTRUMENT PANEL AND CONTROLS engine speed or power may be noticed when the compressor cycles. This is a normal occurrence since the compressor will cycle on and off to maintain comfort and improve fuel economy. Front Mode Control The mode control allows you to choose from several patterns of air distribution. Front Blower Control The front blower controls the amount of air delivered to the passenger compartment. There are four blower speeds.
INSTRUMENT PANEL AND CONTROLS Recirculation Mode (Panel or Bi-Level) Select either the Panel or Bi-Level mode positions when the outside air contains smoke, odors, high humidity, or if rapid cooling of the interior is desired. This feature allows for recirculation of interior air only, when either of these positions are selected. Air flows through the panel outlets or panel and floor outlets in these modes. Panel Outside air flows through the outlets located in the instrument panel.
252 INSTRUMENT PANEL AND CONTROLS NOTE: The air conditioning compressor operates in both Mix and Defrost or a blend of these modes, even if the A/C button has not been pressed. This dehumidifies the air to help dry the windshield. Temperature Control The temperature of the air is controlled by a slide located on the top center of the control panel. Move the slide left or right to change the temperature.
INSTRUMENT PANEL AND CONTROLS Rear Temperature Control — If Equipped Rotating this knob left to the REAR CONTROL position allows the passengers in the second and third row seats to control the blower speed and temperature by means of the rear control located in the rear of the center floor console as described under “Rear Zone Control.” Rotating this knob to the OFF position turns off the rear climate controls.
254 INSTRUMENT PANEL AND CONTROLS Automatic Temperature Control (ATC) — If Equipped The control can be turned on by pressing the Power knob. When the control is turned on, it will be in the last mode prior to being turned off. Pressing the Power knob again will turn off the control. The control can also be turned on by pressing any button and it will display the corresponding operation mode for that button.
INSTRUMENT PANEL AND CONTROLS displayed. The ATC system uses an infrared sensor located in the overhead console to measure the temperature of the driver and passengers. Based on the sensor input, the system will automatically control comfort by varying the temperature, fan speed, and mode. This maintains a comfortable temperature, even under changing conditions. It is important that objects are not blocking the infrared sensor.
256 INSTRUMENT PANEL AND CONTROLS Manual Control (ATC) You may also choose to customize your comfort by selecting the fan speed and mode manually. Turning the fan speed knob or any mode button places the system into manual operation. While in manual operation there are six fan speeds available and the choice of any mode. The airflow temperature is adjusted automatically to maintain the desired comfort level. You can adjust the temperature by pressing the + or - Temp rocker switches.
INSTRUMENT PANEL AND CONTROLS Manual control of recirculation is possible only in Panel, Floor, and Bi-Level modes. It will not operate in Mix, or Defrost modes. The recirculation symbol will flash three times indicating recirculation is not available in these modes. NOTE: If the interior of the windows begin to fog, press the Recirculate button to return to outside air. Some conditions will cause captured interior air to fog windows when in recirculate mode.
258 INSTRUMENT PANEL AND CONTROLS Rear Temperature Control (ATC) The REAR button cycles through the following modes: NOTE: The front display will show “CONTROL IN REAR.” Rear Control From Front This allows the driver or passenger to control the rear blower speeds rotating the Power/Fan knob and the rear temperature using the PASS/REAR Temp +/- rocker switch. While in this mode, pressing the POWER/FAN knob will turn the rear system off. Pressing the Power/ Fan knob will turn the rear system back on.
INSTRUMENT PANEL AND CONTROLS Rear Window Defrosting and Rear Window Washer/Wiper Refer to “Rear Window Features” in Section 4. Rear Zone Climate Control — If Equipped 259 Headliner air comes from the outlets in the headliner. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vane knobs on the outlets to one side will shut off the airflow.
260 INSTRUMENT PANEL AND CONTROLS The rear compartment control uses two rotary knobs: one for the temperature control and the other for the fan speed control. The mode for the rear air conditioning and heating system is always controlled by the front control unit. Fan and temperature can be controlled from the front control unit or the rear control unit.
INSTRUMENT PANEL AND CONTROLS 261 Front Unit to Rear Unit Chart If the Front Control is selected Panel Bi-Level Floor Mix Defrost Rear Airflow will come from Headliner Headliner Floor Floor Floor Operating Tips Rear Storage Ventilation Grilles Fast Cooldown For a fast cooldown, set the blower fan to the highest setting, set the mode control to the panel fresh position, press the Snowflake button to turn on the air conditioning, and drive with the windows open for the first few minutes.
262 INSTRUMENT PANEL AND CONTROLS and adjust the temperature control and blower speed as necessary to maintain comfort. For high humidity conditions, it may be necessary to remain in the Recirculation mode to maintain comfort. Window Fogging Windows will fog on the inside when the humidity inside the vehicle is high. This often occurs in mild or cool temperatures when it’s rainy or humid. In most cases, turning on the air conditioning (pressing the snowflake button) will clear the fog.
INSTRUMENT PANEL AND CONTROLS 263 Operating Tips Chart 4
264 INSTRUMENT PANEL AND CONTROLS REAR WINDOW FEATURES Rear Window Wiper/Washer Automatic Climate Control Panel Manual Climate Control Panel A rotating switch located on the climate control panel turns the rear wiper ON or OFF. Pressing the rotating switch inward activates the rear window washer. Rotating the switch will enable one of five intermittent delay times for the rear wiper. The delay times range from 20 to 1 second.
INSTRUMENT PANEL AND CONTROLS If the rear wiper is operating when the ignition is turned OFF, the wiper will automatically return to the Park position. When the vehicle is restarted, the wiper will resume operation. Rear Window Defrosting A pushbutton type switch is located in the climate control panel. Press the switch and the rear window defroster and electric remote control heated mirrors (if equipped) will turn on. An amber indicator on the pushbutton will light when the defroster is turned on.
STARTING AND OPERATING CONTENTS m Starting Procedures . . . . . . . . . . . . . . . . . . . . . 271 ▫ Torque Converter Clutch . . . . . . . . . . . . . . . . 279 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 271 m Four-Wheel Drive Operation . . . . . . . . . . . . . . . 280 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 271 ▫ NV 140 Transfer Case Operating Information/Precautions – If Equipped . . . . . . 280 m Engine Block Heater – If Equipped . . . . . . . . . .
268 STARTING AND OPERATING ▫ Flowing/Rising Water . . . . . . . . . . . . . . . . . . 287 ▫ Shallow Standing Water . . . . . . . . . . . . . . . . . 287 m Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . 289 m Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . 290 ▫ Four-Wheel Anti-Lock Brake System (ABS) . . . 290 m Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 293 m Electronic Brake Control System . . . . . . . . . . . . 294 ▫ Anti-Lock Brake System (ABS) .
STARTING AND OPERATING 269 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . . 318 m Fuel Requirements . . . . . . . . . . . . . . . . . . . . . . 331 ▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . . 318 ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . . 332 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . . 319 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . . 333 ▫ Alignment And Balance . . . . . . . . . . . . . . . . . 320 ▫ MMT In Gasoline . . . .
270 STARTING AND OPERATING ▫ Fuel Requirements . . . . . . . . . . . . . . . . . . . . 340 ▫ Trailer Hitch Classification . . . . . . . . . . . . . . . 350 ▫ Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles . . . . . . . 340 ▫ Trailer Towing Weights (Maximum Trailer Weight Ratings) . . . . . . . . . . . . . . . . . . . . . . 351 ▫ Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341 ▫ Trailer And Tongue Weight . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! Be sure to turn off the engine and remove the key from the ignition switch if you want to rest or sleep in your car. Accidents can be caused by inadvertently moving the shift lever or by pressing the accelerator pedal.
272 STARTING AND OPERATING Tip Start Feature Your vehicle has a “Tip Start” starting system. With “Tip Start” the driver does not need to hold the key in the START position until the vehicle starts, but can release the key (still in the ignition) and the vehicle will continue through the start cycle. • Turn the ignition key to the START position until the start motor engages.
STARTING AND OPERATING WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly.
274 STARTING AND OPERATING ENGINE BLOCK HEATER – IF EQUIPPED The engine block heater warms the engine coolant and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt AC electrical outlet with a grounded, three wire extension cord. The 3.7L/4.7L engine block heater cord is located at the front of the engine compartment near the radiator cap. The 5.7L engine block heater cord is located on the left side of the engine compartment and rearward of the power distribution center.
STARTING AND OPERATING Gear Ranges DO NOT race the engine when shifting from PARK or NEUTRAL position into another gear range. “P” PARK Supplements parking brake by locking the transmission. Engine can be started in this range. Never use PARK while vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply the parking brake first, then place the shift lever in PARK position.
276 STARTING AND OPERATING WARNING! It is dangerous to shift the gear shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
STARTING AND OPERATING “1” 1st For driving up very steep hills and for engine braking at low speeds (25 mph {40 km/h} or less) when going downhill. To prevent excessive engine speed do not exceed 25 mph (40 km/h) in this range. OVERDRIVE Operation The OVERDRIVE automatic transmission contains an electronically controlled fourth and fifth (if equipped) speed (OVERDRIVE).
278 STARTING AND OPERATING The transmission will downshift from OVERDRIVE to DRIVE if the accelerator pedal is fully depressed at vehicle speeds above approximately 35 mph (56 km/h). When To Use TOW/HAUL Mode When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting occurs, press the TOW/HAUL button. This will improve performance and reduce the potential for transmission overheating or failure due to excessive shifting.
STARTING AND OPERATING Torque Converter Clutch A feature designed to improve fuel economy is included in all automatic transmissions. A clutch within the torque converter engages automatically at a calibrated speed at light throttle. It engages at higher speeds under heavier acceleration. This may result in a slightly different feeling or response during normal operation in high gear.
280 STARTING AND OPERATING FOUR-WHEEL DRIVE OPERATION NV 140 Transfer Case Operating Information/Precautions – If Equipped The NV 140 is a single speed (4 HI range only) transfer case which provides convenient full-time 4-wheel drive. No driver interaction is required. This transfer case divides engine torque almost evenly with 48 percent of engine torque to the front axle and 52 percent of engine torque to the rear axle. 4WD Normal 4-Wheel Drive High Range - Employs inter-axle differential.
STARTING AND OPERATING different speeds. This eliminates driveline binding and component wear normally associated with driving the vehicle in the 4WD LOCK position on dry, hard-surfaced roads. This feature provides the safety, security, and convenience of operating in all-wheel drive at all times regardless of road conditions.
282 STARTING AND OPERATING WARNING! Always engage the parking brake when powering down the vehicle if the (SVC 4WD( light is illuminated. Not engaging the parking brake may allow the vehicle to roll, which may cause personal injury. NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning. The NV 244 Generation II transfer case is not equipped with a synchronizer and therefore the front and rear driveshaft speeds must be equal for the shift to take place.
STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake. The transfer case NEUTRAL position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move, regardless of the transmission position. The parking brake should always be applied when the driver is not in the vehicle.
284 STARTING AND OPERATING 4WD LOW The 4-Wheel Drive Low (4WD LOW) Range provides low speed 4-wheel drive. It locks the front and rear driveshafts together, forcing the front and rear wheels to rotate at the same speed. This range provides additional traction and maximum pulling power for loose or slippery road surfaces only. Do not exceed 25 mph (40 km/h). Shifting Procedure - NV 244 Generation II Transfer Case N The NEUTRAL ranged disengages both the front and rear driveshafts from the powertrain.
STARTING AND OPERATING wheels to complete the shift. There may be a delay up to 13 seconds for the shift to complete after the wheels have stopped spinning. NOTE: Delayed shifting out of the 4WD LOCK position may be experienced due to uneven tire wear, low tire pressure, or excessive loading. NOTE: When shifting into, or out of 4WD LOW, some gear noise may be heard. This noise is normal and is not detrimental to the vehicle or occupants.
286 STARTING AND OPERATING NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift. The indicator light will flash and the current transfer case position will be maintained. To retry the selection, turn the control knob back to the current position, wait five seconds, and retry the shift. 1. Slow down during rainstorms or when roads are slushy.
STARTING AND OPERATING Flowing/Rising Water WARNING! Do not drive on, or cross, a road or a path where water is flowing and/or rising (as in storm run-off). Flowing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehicle away swiftly. Failure to follow this warning may result in injuries that are serious or fatal to you, your passengers, and others around you.
288 STARTING AND OPERATING CAUTION! WARNING! • Driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.e., engine oil, transmission, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water. Do not continue to operate the vehicle if any fluid appears contaminated, as this may result in further damage.
STARTING AND OPERATING PARKING BRAKE The foot operated parking brake is positioned below the lower left corner of the instrument panel. To release the parking brake, pull the parking brake release handle. 289 Be sure the parking brake is firmly set when parked and the shift lever is in PARK position.
290 STARTING AND OPERATING WARNING! • Always fully apply the parking brake when leaving your vehicle, or the vehicle may roll and cause damage or injury. Also be certain to leave an automatic transmission in Park. Failure to do so may cause the vehicle to roll and cause damage or injury. • Be sure the parking brake is fully disengaged before driving, failure to do so can lead to brake failure and an accident. • Never leave children alone in a vehicle.
STARTING AND OPERATING surfaces. All vehicle wheels and tires must be the same size and type and tires must be properly inflated to produce accurate signals for the computer. WARNING! Significant over-or-under-inflation of tires, or mixing sizes of tires or wheels on the vehicle can lead to loss of braking effectiveness. The ABS conducts a low-speed self-test at about 12 mph (20 km/h). If you have your foot lightly on the brake while this test is occurring you may feel slight pedal movement.
292 STARTING AND OPERATING WARNING! WARNING! ABS contains sophisticated electronic equipment. It may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be done by qualified professionals.
STARTING AND OPERATING When you are in a severe braking condition involving use of the ABS, you will experience some pedal drop as the vehicle comes to a stop. This is the result of the system reverting to the base brake system. Engagement of the ABS may be accompanied by a pulsing sensation. You may also hear a clicking noise. These occurrences are normal, and indicate that the system is functioning properly.
294 STARTING AND OPERATING CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and should be avoided when possible. Damage to the power steering pump may occur.
STARTING AND OPERATING WARNING! 295 BAS (Brake Assist System) • ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
296 STARTING AND OPERATING The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes. The system applies optimum pressure to the brakes in emergency braking conditions. This can help reduce braking distances. The BAS complements the ABS. Applying the brakes very quickly results in the best BAS assistance.
STARTING AND OPERATING Traction Control System (TCS) This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the TCS system functions similar to a limited slip differential and controls the wheel spin across a driven axle.
298 STARTING AND OPERATING WARNING! Many factors, such as vehicle loading, road conditions and driving conditions, influence the chance that wheel lift or rollover may occur. • ERM cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING • Understeer - when the vehicle is turning less than appropriate for the steering wheel position. ESP/TCS Indicator Light The ESP/TCS Indicator Light starts to flash as soon as the tires lose traction and the TCS or ESP system becomes active. It will also flash once a swaying trailer is detected and the Trailer Sway Control (TSC) system activates. If the ESP/ TCS Indicator Light begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible.
300 STARTING AND OPERATING 4WD/4WD LOCK or 2WD Models ON This is the normal operating mode for ESP in 4WD LOCK and in 2WD vehicles. Whenever the vehicle is started or the transfer case (if equipped) is shifted from 4WD LOW or NEUTRAL back to 4WD LOCK, the ESP system will be in this mode. This mode should be used for almost all driving situations. ESP should only be turned to “Partial Off” for specific reasons as noted below.
STARTING AND OPERATING 301 NOTE: To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, it may be desirable to switch to the “Partial Off” mode by pressing the ESP Control Switch. Once the situation requiring ESP to be switched to the “Partial Off” mode is overcome, turn ESP on by momentarily depressing the ESP Control Switch. This may be done with the vehicle in motion.
302 STARTING AND OPERATING WARNING! In the Partial Off mode, the engine torque reduction and stability features are desensitized. Therefore, the enhanced vehicle stability offered by ESP is unavailable. ESP/BAS Warning Lamp and ESP/TCS Indicator Light The malfunction indicator for the ESP is combined with the BAS indicator. The yellow ESP/BAS Warning Light and the yellow ESP/TCS Indicator Light in the instrument cluster both come on when the ignition switch is turned to the ON position.
STARTING AND OPERATING stop the sway. The system will reduce engine power and apply individual brakes that will counter act the sway of the trailer. TSC will become active automatically once the swaying trailer is recognized. No driver action is required. TSC cannot stop all trailers from swaying. Always use caution when towing a trailer and follow the tongue weight recommendations. For additional information on towing a trailer with your vehicle, refer to 9Trailer Towing9 in Section 5.
304 STARTING AND OPERATING • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter 9P9 is absent from this tire size designation. Example: 215/65R15 96H • Temporary spare tires are high-pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
STARTING AND OPERATING 305 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards (....blank....( = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%). —Ratio of section height to section width of tire 10.
306 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, 307 located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
308 STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side B-pillar.
STARTING AND OPERATING 309 Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard and in the “Vehicle Loading” section of this manual.
310 STARTING AND OPERATING available cargo and luggage load capacity is 650 lbs (295 kg) {(since 5 x 150 = 750, and 1400 – 750 = 650 lbs (295 kg)}. 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle.
STARTING AND OPERATING 311 5
312 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under-inflation also increases tire rolling resistance and results in higher fuel consumption. 313 maximum loaded vehicle condition. These pressure conditions will be found in the “Supplemental Tire Pressure Information” section of this manual. 3.
314 STARTING AND OPERATING check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under-inflated. CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.
STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high-speed vehicle operation.
316 STARTING AND OPERATING Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and reinstalled at the first opportunity. WARNING! Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). Temporary use spare tires have limited tread life.
STARTING AND OPERATING 317 original equipped tire on the front or rear axle of your vehicle, but it is not. Installation of this limited-use spare tire affects vehicle handling. Since it is not the same tire, replace (or repair) the original tire and reinstall on the vehicle at the first opportunity. Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck.
318 STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Many states have laws requiring tire replacement at this point.
STARTING AND OPERATING WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death. Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline.
320 STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. SUPPLEMENTAL TIRE PRESSURE INFORMATION — IF EQUIPPED A light load vehicle condition is defined as two passengers [150 lbs (68 kg) each] plus 200 lbs (91 kg) of cargo. Cold tire inflation pressures for a lightly loaded vehicle will be found on the face of the driver’s door.
322 STARTING AND OPERATING These cautions apply to all chain traction devices, including link and cable (radial) chains. Tire chain use is permitted only on the rear tires of your truck. NOTE: The use of class “S” chains is permitted on your vehicle with P245/70R17 tires. CAUTION! Do not use tire chains on 4x4 trucks equipped with tires other than P245/70R17 tires. There may not be adequate clearance for the chains and you are risking structural or body damage to your vehicle.
STARTING AND OPERATING 323 TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates and tend to develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all season type tires.
324 STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM (TPMS) — IF EQUIPPED The Tire Pressure Monitoring System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure (the placard is located on the driver’s side B-pillar). The tire pressure will vary with temperature by about 1 psi (6.9 kPa) for every 12°F (6.5°C). This means that when the outside temperature decreases, the tire pressure will decrease.
STARTING AND OPERATING For example, your vehicle has a recommended cold (parked for more than three hours) placard pressure of 33 psi (227 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 28 psi (193 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressure to approximately 24 psi (165 kPa). This tire pressure is sufficiently low enough to turn on the TPMS light.
326 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the tire pressure monitoring sensor. NOTE: • The TPMS is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure.
STARTING AND OPERATING 327 NOTE: It is particularly important for you to check the tire pressure in all of your tires regularly and to maintain the proper pressure. received. The vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) to receive this information. The TPMS consists of the following components: The Tire Pressure Monitoring Telltale Lamp will flash on and off for 75 seconds, and remain on solid when a system fault is detected. The system fault will also sound a chime.
328 STARTING AND OPERATING NOTE: Your vehicle is equipped with a non-matching full size spare wheel and tire assembly. 1. This spare tire does not have a tire pressure monitoring sensor. Therefore, the TPMS will not monitor the tire pressure in the spare tire. 2. If you install the full size spare tire in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition key cycle a chime will sound and the TPM Telltale Lamp will still turn ON due to the low tire. 3.
STARTING AND OPERATING The TPMS consists of the following components: • Receiver module • Four tire pressure monitoring sensors • Three trigger modules (mounted in three of the four wheel wells). • Various TPMS messages, which display in the Electronic Vehicle Information Center (EVIC), and a graphic displaying tire pressures. • Yellow Tire Pressure Monitoring Telltale Light.
330 STARTING AND OPERATING the pressure value(s) indicating which tire pressure monitoring sensor(s) is not being received. If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the Tire Pressure Monitoring Telltale Light will no longer flash, the 9CHECK TPM SYSTEM9 text message will not be present, and a pressure value will be displayed instead of dashes.
STARTING AND OPERATING 331 display a “CHECK TPM SYSTEM” message for three seconds, and then display dashes (- - -) in place of a pressure value. • This device must accept any interference received, including interference that may cause undesired operation. 5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the full size spare tire, the TPMS will update automatically.
332 STARTING AND OPERATING The 5.7L engine is designed to meet all emissions regulations and provide satisfactory fuel economy and performance when using high quality unleaded gasoline having an octane range of 87 to 89. The manufacturer recommends the use of 89 octane for optimum performance. The use of premium gasoline is not recommended.
STARTING AND OPERATING Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as 10% ethanol, MTBE and ETBE. Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygenates may be used in your vehicle. CAUTION! DO NOT use gasoline containing Methanol or E85 Ethanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components.
334 STARTING AND OPERATING of gasoline may not be indicated on the gasoline pump, therefore, you should ask your gasoline retailer whether or not his/her gasoline contains MMT. It is even more important to look for gasolines without MMT in Canada, because MMT can be used at levels higher than those allowed in the United States. MMT is prohibited in Federal and California reformulated gasoline.
STARTING AND OPERATING NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. 335 Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill.
336 STARTING AND OPERATING ADDING FUEL CAUTION! Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. NOTE: To avoid contact between fuel cap and paint, hang tether strap over hook provided on inner fuel door. CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap).
STARTING AND OPERATING 337 WARNING! WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. • Never add fuel when the engine is running. This is in violation of most state and federal fire regulations and may cause the Malfunction Indicator Light to turn on.
338 STARTING AND OPERATING the problem is detected twice in a row, the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem will turn the MIL light off. manual for information on features that are common between Flexible Fuel and gasoline-only powered vehicles. CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler cap (gas cap). A poorly fitting cap could let impurities into the fuel system.
STARTING AND OPERATING CAUTION! Only vehicles with the E-85 fuel filler cap (gas cap) can operate on E-85. 339 ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame.
340 STARTING AND OPERATING Fuel Requirements Your vehicle will operate on both unleaded gasoline with an octane rating of 87, or E-85 fuel, or any mixture of these two. NOTE: When the ambient temperature is above 90°F (32°C), you may experience hard starting and rough idle following startup, even if the above recommendations are followed. For best results, a refueling pattern that alternates between E-85 and unleaded gasoline should be avoided.
STARTING AND OPERATING Starting The characteristics of E-85 fuel make it unsuitable for use when ambient temperatures fall below 0°F (-18°C). In the range of 0°F (-18°C) to 32°F (0°C), you may experience an increase in the time it takes for your engine to start, and a deterioration in drivability (sags and/or hesitations) until the engine is fully warmed up. CAUTION! Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect drivability.
342 STARTING AND OPERATING VEHICLE LOADING Certification Label As required by National Highway Traffic Safety Administration Regulations, your vehicle has a certification label affixed to the driver’s side door. This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Rating (GAWR) front and rear, and Vehicle Identification Number (VIN). A Month-Day-Hour (MDH) number is included on this label and shows the month, day, and hour of manufacture.
STARTING AND OPERATING Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles. The load must be distributed in the cargo area so that the GAWR of each axle is not exceeded. Each axle GAWR is determined by the component in the system with the lowest load carrying capacity (axle, springs, tires, or wheels). Heavier axles or suspension components sometimes specified by purchasers for increased durability do not necessarily increase the vehicle’s GVWR.
344 STARTING AND OPERATING should then be determined separately to be sure that the load is properly distributed over front and rear axle. Weighing the vehicle may show that the GAWR of either the front or rear axles has been exceeded but the total load is within the specified GVWR. If so, weight must be shifted from front to rear or rear to front as appropriate until the specified weight limitations are met. Store heavier items down low and be sure that the weight is distributed equally.
STARTING AND OPERATING after the vehicle has been weighed both in its (curb weight( condition, and in its (loaded and ready for operation( condition. Gross Vehicle Weight Rating (GVWR) 6500 LBS. 345 TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer carefully review this information to tow your load as efficiently and safely as possible.
346 STARTING AND OPERATING Gross Trailer Weight (GTW) The Gross Trailer Weight (GTW) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its 9loaded and ready for operation9 condition. The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale.
STARTING AND OPERATING Frontal Area The maximum height and maximum width of the front of a trailer. TSC (Trailer Sway Control) – If Equipped • Trailer Sway Control – Electronic TSC uses sensors in the vehicle to recognize a swaying trailer and will take the appropriate actions to attempt to stop the sway. The system will reduce engine power and apply individual brakes that will counteract the sway of the trailer. TSC will become active automatically once the swaying trailer is recognized.
348 STARTING AND OPERATING used in accordance with the manufacturers’ directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety. The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability.
STARTING AND OPERATING 349 5 Weight-Distributing Hitch System Improper Adjustment Of Weight-Distributing System Fifth-Wheel Hitch A fifth-wheel hitch is a special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed. Connects a vehicle and fifth-wheel trailer with a coupling king pin.
350 STARTING AND OPERATING Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck. The coupling arm connects to the hitch mounted over the rear axle in the truck bed. Trailer Hitch Classification The rear bumper is intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alterations to the standard equipment.
STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) 351 Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. NOTE: For additional trailer towing information (maximum trailer weight ratings) refer to the following website addresses: • http:// www.dodge.com/towing • http:// www.dodge.ca (Canada) Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer.
352 STARTING AND OPERATING Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer. • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle.
STARTING AND OPERATING WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident. • When hauling cargo or towing a trailer, do not overload your vehicle or trailer.
354 STARTING AND OPERATING 2. GTW 3. GAWR 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight.) Towing Requirements — Tires − Do not attempt to tow a trailer while using a compact spare tire. − Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING − An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. − Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg).
356 STARTING AND OPERATING Towing Requirements — Trailer Lights and Wiring Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package may include a 4- and 7-pin wiring harness. Use a factory approved trailer harness and connector. NOTE: Do not cut or splice wiring into the vehicle’s wiring harness.
STARTING AND OPERATING 357 If using a manual transmission vehicle for trailer towing, all starts must be in 1stT gear to avoid excessive clutch slippage. Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the TOW/ HAUL feature should be selected. 7-Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic.
358 STARTING AND OPERATING NOTE: Check the automatic transmission fluid level before towing. Towing Tips — Tow/Haul (If Equipped) To reduce potential for automatic transmission overheating, turn the TOW/HAUL feature ON when driving in hilly areas or shift the transmission to Drive position 2 on more severe grades. Towing Tips — Electronic Speed Control (If Equipped) − Don’t use in hilly terrain or with heavy loads.
STARTING AND OPERATING SNOWPLOW 359 CAUTION! NOTE: Do not use this vehicle for snowplow applications. Using this vehicle for snowplow applications can cause damage to the vehicle. WARNING! Snowplows, winches, and other aftermarket equipment should not be added to the front end of your vehicle. The airbag crash sensors may be affected by the change in the front end structure. The airbags could deploy unexpectedly or could fail to deploy during a collision, resulting in serious injury or death.
360 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Recreational Towing 2WD Models Recreational towing of 2WD models is not allowable. Towing the vehicle with the transmission in NEUTRAL can cause severe transmission damage. Removal of the driveshaft for towing is not recommended since this allows transmission fluid to leak out.
STARTING AND OPERATING NOTE: The NV 244 Generation II transfer case must be shifted into NEUTRAL for recreational towing. The NEUTRAL selection button is located on the lower left-hand corner of the 4WD Control Switch. Shifts into and out of transfer case NEUTRAL can take place with the selector switch in any mode position. Shifting into NEUTRAL Use the following procedure to prepare your vehicle for recreational towing.
362 STARTING AND OPERATING 12. Turn ignition key to the unlocked OFF position. 13. Shift the automatic transmission into PARK. 14. Attach vehicle to tow vehicle with tow bar. NOTE: Items 1 through 5 are requirements that must be met prior to depressing the NEUTRAL selection button, and must continue to be met until the four seconds elapses and the shift has been completed.
STARTING AND OPERATING 5. Shift the automatic transmission to NEUTRAL. 6. Using the point of a ballpoint pen or similar object, depress the recessed transfer case NEUTRAL button for one second. 7. After the NEUTRAL indicator light turns off, release the NEUTRAL button. 8. After the NEUTRAL button has been released, the transfer case will shift to the position identified by the selector switch. 9. Shift the automatic transmission into PARK. 10. Start the engine. 11.
364 STARTING AND OPERATING CAUTION! • Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and damage internal parts. EQUIPMENT IDENTIFICATION PLATE The equipment Identification Plate is located on the hood inner surface.
WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 366 m Jump–Starting Procedures . . . . . . . . . . . . . . . . . 376 m Jacking And Tire Changing . . . . . . . . . . . . . . . . 367 m Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . 378 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . . 368 m Emergency Tow Hooks — If Equipped . . . . . . . . 378 m Jacking Instructions . . . . . . . . . . . . . . . . . . . . .
366 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is on the top of the steering column, just behind the steering wheel. Press the flasher switch and all front and rear directional signals will flash intermittently. Press the switch a second time to turn off the emergency flashers. Flasher Switch This is an emergency warning system and should not be used when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists.
WHAT TO DO IN EMERGENCIES If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and the vehicle locked. 367 JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
368 WHAT TO DO IN EMERGENCIES Jack Location The scissor jack and tire changing tools are stowed under the second row seat. The jack is secured in place with a winged stud and a fixed stud. It is very important to secure the jack tightly in place by engaging the slot in the base to the fixed stud under the middle seat. The winged stud inserts through the eyelet in the end of the jack’s worm screw.
WHAT TO DO IN EMERGENCIES JACKING INSTRUCTIONS Removing The Spare Tire The spare tire on your vehicle is located underneath the vehicle in the rear. 369 1. Remove the rubber plug from the floor in the cargo area. 6 Spare Tire Winch Spare Tire Location Remove the spare tire before attempting to jack the vehicle. 2. Engage the jack wrench extension to the spare tire winch through the hole in the floor.
370 WHAT TO DO IN EMERGENCIES 3. Turn the wrench counterclockwise to lower the spare tire. Continue to turn the wrench until the spare tire can be pulled out from under the vehicle. It is recommended that you stow the flat tire or spare to avoid tangling the loose cable. CAUTION! The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch.
WHAT TO DO IN EMERGENCIES • Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. Preparations Park the vehicle on a firm level surface, avoiding ice or slippery areas. Set the parking brake and place the shift lever in PARK (automatic transmission). On 4-wheel drive vehicles, shift the transfer case to the “4L” position.
372 WHAT TO DO IN EMERGENCIES 1. Remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. 3. When changing a front wheel, place the jack under the frame rail behind the wheel. Locate the jack as far forward as possible on the straight part of the frame (prior to inboard transition).
WHAT TO DO IN EMERGENCIES 373 When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle as close to the tire as posssible with the drive tubes extending to the rear. Connect the jack tube extension and wheel wrench. 6 Rear Right Jacking Location Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required.
374 WHAT TO DO IN EMERGENCIES WARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station. WARNING! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle.
WHAT TO DO IN EMERGENCIES WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised. • Apply the parking brake firmly before jacking. • Never start the engine with the vehicle on a jack. • Do not let anyone sit in the vehicle when it is on a jack.
376 WHAT TO DO IN EMERGENCIES JUMP–STARTING PROCEDURES WARNING! • Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush the contaminated area immediately with large quantities of water. • A battery generates hydrogen gas which is flammable and explosive. Keep flame or spark away from the vent holes.
WHAT TO DO IN EMERGENCIES 4. Connect one end of a jumper cable to the positive terminal of the booster battery. Connect the other end of the same cable to the positive terminal of the discharged battery. WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result. 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery.
378 WHAT TO DO IN EMERGENCIES WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; The least amount of accelerator pedal pressure to maintain the rocking motion without spinning the wheels or racing the engine is most effective. Allow the engine to idle with the shift lever in NEUTRAL for at least one minute after every five rocking-motion cycles.
WHAT TO DO IN EMERGENCIES 379 WARNING! CAUTION! Chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. Tow hooks are for emergency use only, to rescue a vehicle stranded off-road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. WARNING! Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury.
380 WHAT TO DO IN EMERGENCIES Four-Wheel Drive Vehicles The manufacturer recommends towing with all wheels OFF the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of the vehicle raised and the opposite end on a towing dolly. If the vehicle is to be towed more than 15 mi (25 km) or faster than 30 mph (50 km/h), it must be towed on a flatbed, or with the rear wheels raised and the front wheels on the ground, or with the front end raised and the rear wheels on a towing dolly.
MAINTAINING YOUR VEHICLE CONTENTS m Engine Compartment 4.7L V-8 . . . . . . . . . . . . . . 384 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 390 m Engine Compartment 5.7L HEMI V-8 . . . . . . . . . 385 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . . 393 m Onboard Diagnostic System — OBD II . . . . . . . . 386 ▫ Drive Belts — Check Condition And Tension . . 393 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . . 386 ▫ Spark Plugs . . . . . . . . . . . . . . . .
382 MAINTAINING YOUR VEHICLE ▫ Air Conditioner Maintenance . . . . . . . . . . . . . 398 ▫ Front Suspension Ball Joints . . . . . . . . . . . . . . 399 ▫ Drive Shaft Constant Velocity Joints . . . . . . . . 400 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . . 400 ▫ Windshield Wiper Blades . . . . . . . . . . . . . . . . 400 ▫ Windshield And Rear Window Washers . . . . . 401 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . . 401 ▫ Cooling System . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 383 ▫ Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 435 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437 m Fluids And Capacities . . . . . . . . . . . . . . . . . . . 436 ▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . 438 m Fluids, Lubricants And Genuine Parts . . . . . . . .
384 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT 4.
MAINTAINING YOUR VEHICLE 385 ENGINE COMPARTMENT 5.
386 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE the odometer RESET button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the MIL. Resolving the problem will turn the MIL off. EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system.
388 MAINTAINING YOUR VEHICLE 4. Approximately 15 seconds later, one of two things will happen: a. The MIL will blink for approximately five seconds and then remain on until the first engine crank or the key is turned off. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b. The MIL will remain fully illuminated until the first engine crank or the key is turned off. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station.
MAINTAINING YOUR VEHICLE DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
390 MAINTAINING YOUR VEHICLE These items should be inspected if a malfunction is observed or suspected. Engine Oil Checking Oil Level To assure proper lubrication of your vehicle’s engine, the engine oil must be maintained at the correct level. The best time to check the engine oil level is about five minutes after a fully warmed up engine is shut off or before starting the engine after it has sat overnight.
MAINTAINING YOUR VEHICLE Change Engine Oil Follow the Maintenance Schedule for recommended engine oil and filter change intervals. NOTE: Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or 6 months, whichever comes first. 4x4 Models, If Used Primarily For Off-Road Operation Every 50 hours of use. Dusty Conditions Driving through dust-laden air increases the problems of keeping abrasive materials out of the engine.
392 MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your vehicle. For information on engine oil filler cap location, see the Engine Compartment illustration in this section. NOTE: Vehicles equipped with a 5.7L engine must use SAE 5W-20 oil.
MAINTAINING YOUR VEHICLE station, or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Engine Oil Filter Selection The manufacturer’s engines have a full-flow type oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high quality filters should be used to assure most efficient service.
394 MAINTAINING YOUR VEHICLE Spark Plugs Spark plugs must fire properly to assure proper engine performance and emission control. The plugs installed in your vehicle should operate satisfactorily in normal service for the mileage indicated in the Maintenance Chart. New plugs should be installed at this mileage. The entire set should be replaced if there is any malfunction due to a faulty spark plug.
MAINTAINING YOUR VEHICLE Engine Fuel Filter A plugged fuel filter can cause stalling, limit the speed at which a vehicle can be driven or cause hard starting. Should an excessive amount of dirt accumulate in the fuel tank, frequent filter replacement may be necessary. See your authorized dealer for service. Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device.
396 MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may indicate severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE 397 WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.
398 MAINTAINING YOUR VEHICLE Power Steering — Fluid Check Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized DaimlerChrysler dealership.
MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information book for further warranty information. • The air conditioning system contains refrigerant under high pressure.
400 MAINTAINING YOUR VEHICLE Drive Shaft Constant Velocity Joints All 4-wheel drive models are equipped with four constant velocity joints. Periodic lubrication of these joints is not required. However, the joint boot should be inspected for external leakage or damage periodically. If external leakage or damage is evident, the joint boot and grease should be replaced immediately. Continued operation could result in failure of the joint due to water and dirt contamination of the grease.
MAINTAINING YOUR VEHICLE Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Windshield and Rear Window Washers The fluid reservoir for the windshield washers and the rear window washer is shared. The fluid reservoir is located in the engine compartment: be sure to check the fluid level at regular intervals. Fill the reservoir with windshield washer solvent only (not radiator antifreeze).
402 MAINTAINING YOUR VEHICLE damaged, have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required. WARNING! Exhaust gases can injure or kill.
MAINTAINING YOUR VEHICLE clean by gently spraying water from a garden hose vertically down the face of the condenser and radiator. Check the coolant recovery bottle tubing for brittle rubber, cracking, tears, cuts and tightness of the connection at the bottle and radiator. Inspect the entire system for leaks. With the engine at normal operating temperature (but not running), check the cooling system pressure cap for proper vacuum sealing by draining a small amount of coolant from the radiator drain cock.
404 MAINTAINING YOUR VEHICLE CAUTION! • Mixing of coolants other than specified HOAT engine coolants may result in engine damage and may decrease corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible. • Do not use plain water alone or alcohol-based engine coolant (antifreeze) products.
MAINTAINING YOUR VEHICLE • Use only high purity water such as distilled or deionized water when mixing the water/engine coolant solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated.
406 MAINTAINING YOUR VEHICLE Disposal of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately.
MAINTAINING YOUR VEHICLE • Do not overfill the coolant recovery bottle. • Check coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze needs to be added, contents of coolant recovery bottle must also be protected against freezing. • If frequent coolant additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks.
408 MAINTAINING YOUR VEHICLE Ensure nylon tubing in these areas has not melted or collapsed. Inspect all hose clamps and couplings to make sure they are secure and no leaks are present. NOTE: Fluids such as oil, power steering fluid, and brake fluid are used during assembly plant operations to ease the assembly of hoses to couplings. Therefore, oil wetness at the hose-coupling area is not necessarily an indication of leakage.
MAINTAINING YOUR VEHICLE Brake Master Cylinders The fluid level in the master cylinders should be checked whenever the vehicle is serviced, or immediately if the brake system warning light is on. If necessary, add fluid to bring level to the full mark on the side of the reservoir of the brake master cylinder. Be sure to clean the top of the master cylinder area before removing the cap. With disc brakes, fluid level can be expected to fall as the brake pads wear.
410 MAINTAINING YOUR VEHICLE CAUTION! WARNING! Do not allow a petroleum-base fluid to contaminate the brake fluid. Seal damage may result. Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any sign of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Brake Hoses Inspection should be performed whenever the brake system is serviced or at intervals specified. Inspect hydraulic brake hoses for surface cracking, scuffing or worn spots.
MAINTAINING YOUR VEHICLE least 15 miles (24 km) of driving. At normal operating temperature the fluid cannot be held comfortably between the fingertips. To check the automatic transmission fluid level properly, the following procedure must be used: 1. Operate the engine at idle speed and normal operating temperature. 2. The vehicle must be on level ground. 3. Fully apply the parking brake and press the brake pedal. 4. Place the shift lever momentarily in each gear position ending with the lever in PARK. 5.
412 MAINTAINING YOUR VEHICLE CAUTION! Be aware that if the fluid temperature is below 50°F (10°C) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. 7. Check for leaks. Release parking brake. To prevent dirt and water from entering the transmission after checking or replenishing fluid, make certain that the dipstick cap is properly reseated.
MAINTAINING YOUR VEHICLE 413 CAUTION! CAUTION! Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturer’s recommended fluid will result in more frequent fluid and filter changes. For correct fluid type, refer to “Automatic Transmission” under “Fluids, Lubricants and Genuine Parts” in this section.
414 MAINTAINING YOUR VEHICLE NOTE: The presence of water in the gear lubricant will result in corrosion and possible failure of differential components. Operation of the vehicle in water, as may be encountered in some off-highway types of service, will require draining and refilling the axle to avoid damage.
MAINTAINING YOUR VEHICLE The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! • Insects, tree sap and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants. 415 Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces.
416 MAINTAINING YOUR VEHICLE • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc.
MAINTAINING YOUR VEHICLE • For tough stains, apply Mopart Total Clean or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • For grease stains, apply Mopart Multi-Purpose Cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • Do not use any solvents YES Essentialst products. or protectants on Interior Care Use Mopart Fabric Cleaner to clean fabric upholstery and carpeting.
418 MAINTAINING YOUR VEHICLE Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. defrosters or windshields equipped with a windshield wiper de-icer. Do not use scrapers or other sharp instruments which may scratch the elements. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.
MAINTAINING YOUR VEHICLE Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the vehicle to wash them. Replace the belts if they appear frayed or worn or if the buckles do not work properly.
420 MAINTAINING YOUR VEHICLE Fuses (Interior) The fuse block contains blade-type mini-fuses, relays, and circuit breakers for high-current circuits. It is located in the left kick panel. It is accessible through a snap-in cover.
MAINTAINING YOUR VEHICLE Cavity Mini Fuse/ Color F1 15 Amp Blue F2 10 Amp Red F3 10 Amp Red F4 10 Amp Red F5 (2) 10 Amp Red Description Instrument Cluster Battery Feed Spare Ignition Run/Start for Next Generation Controller (NGC), Integrated Power Module (IPM), A/C Relay and Fuel Pump Relay Door Node and Non-Memory Power Mirror Switch Battery Feed Airbags (two Fuses in Yellow Holder) 421 F6 2 Amp Clear Ignition Run/Start Unlock F7 25 Amp Natural Radio Battery Feed F8 F9 F10 F11 F12 I
422 MAINTAINING YOUR VEHICLE F13 F14 F15 F16 F17 Ignition Run HVAC Module/Heated 10 Amp Red Rear Glass (EBL) Relay ABS Module Igni10 Amp Red tion Run Battery Feed Bluetootht, Compass/Trip 15 Amp Blue Computer (CMTC), Sentry Keyt Diagnostics Reconfigurable 20 Amp Yellow Power Outlets Ignition Run / Rear Park Assist / Sec20 Amp Yellow ond Row Heated Seats F18 F19 F20 F21 Cigar Lighter Ignition 10 Amp Red Spare Fuse Heating & Air Con15 Amp Blue ditioning w/ATC Only Battery Feed 25 Amp Natu- Amplifier
MAINTAINING YOUR VEHICLE Fuses (Power Distribution Center) stamped on the inside cover, otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart. These fuses and relays can be obtained from your authorized dealer. Cavity 1 2 3 Power Distribution Center Your vehicle is equipped with an electrical power distribution center located in the left side of the engine compartment. This center contains cartridge fuses, mini fuses and relays.
424 MAINTAINING YOUR VEHICLE Cavity 7 8 9 10 11 12 13 14 Cartridge Fuse / Relay 40 Amp Green 40 Amp Green Spare 30 Amp Pink 40 Amp Green 40 Amp Green 30 Amp Pink 40 Amp Green Mini Fuse Description Cavity Blower Motor Relay Feed JB Feed Acc Delay 16 ASD 17 18 Power Liftgate ( If Equipped) JB Feed / Heated Rear Glass (EBL)/TCase Brake JB Feed RR 15 19 20 21 22 ESP Pump Cartridge Fuse / Relay 50 Amp Red Mini Fuse Description JB Feed 10 Amp Red Spare 20 Amp Yellow 20 Amp Yellow 25 Amp Clear 2
MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse / Relay 23 20 Amp Yellow 15 Amp Blue 15 Amp Blue Spare 20 Amp Yellow Spare 24 25 26 27 28 29 30 31 32 Mini Fuse Relay Relay Spare Relay Trailer Tow 33 Cartridge Fuse / Relay Relay A/C Clutch 34 35 36 37 38 39 40 Relay Relay Spare Relay Spare Relay Relay Description Stop Lamp Switch Run/Start Relay Feed Run Start Run Remote Starter Cavity Mini Fuse 425 Description Electronic Automatic Transaxle (EATX) AC Clutch Fuel Pump Rly Stop Lamp Switch
426 MAINTAINING YOUR VEHICLE Fuses (Integrated Power Module) otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart. 1 2 3 4 5 Cartridge Fuse / Relay Relay Relay Relay Relay Relay 6 Relay 7 8 Relay Cavity Mini Fuse Integrated Power Module An integrated power module is located in the left side of the engine compartment. This center contains cartridge fuses, mini fuses and relays.
MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse / Relay 10 11 12 13 14 15 16 17 Mini Fuse 10 Amp Red Relay 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow Description Cavity Rt Park Lamps 18 Radiator Fan Hi Rly Front Control Module (FCM) Batt #4 Front Control Module (FCM) Batt #2 Adjustable Pedal 19 21 22 23 Horn 24 25 26 Mini Fuse 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Ft Fog Lamps Rear Wiper Cartridge Fuse / Relay 30 Amp Pink 40 Amp
428 MAINTAINING YOUR VEHICLE Cavity 27 28 29 30 Cartridge Fuse / Relay Mini Fuse 30 Amp Green 30 Amp Green Description Ignition Off Draw (IOD) #1 Ignition Off Draw (IOD) #2 Spare Spare VEHICLE STORAGE If you are storing your vehicle for more than 21 days, we recommend that you take the following steps to minimize the drain on your vehicle’s battery: • Disconnect the Ignition Off Draw (I.O.D.) fuses located in the Power Distribution Center (PDC). The I.O.D.
MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Dome Light . . . . . . . . . . . . . . . . . . . . Not Liftgate Lamp . . . . . . . . . . . . . . . . . . . . . . Overhead Console Lights. . . . . . . . . . . Not Reading Light. . . . . . . . . . . . . . . . . . . Not Visor Vanity Lights . . . . . . . . . . . . . . . Not 429 BULB REPLACEMENT Bulb No. Serviceable . . . . . 567 Serviceable Serviceable Serviceable LIGHT BULBS — Exterior Bulb No. Headlight . . . . . . . . . . . . . . . .
430 MAINTAINING YOUR VEHICLE 2. Remove one nut that attaches the headlight to the inner fender panel. Access to the nut is possible by opening the fender panel access door which is located in the wheel liner. 4. While firmly holding the headlight in your hands disconnect all connectors by following the procedure described in step number 5 below. 5. Remove the bulb connector from the headlight making sure to pull and release the red tab on all connectors.
MAINTAINING YOUR VEHICLE Tail Lights, Turn Signals And Backup Lights — Replacement 431 2. Rotate the light to the outboard side of the vehicle and remove. 1. Remove the two push-pins from the tail light housing.
432 MAINTAINING YOUR VEHICLE 3. Unlock and remove electrical connector. 4. Twist bulb sockets counterclockwise to remove from housing. 5. Remove the bulbs from the bulb sockets by pulling the bulb straight out.
MAINTAINING YOUR VEHICLE License Lights 433 2. Rotate the socket 1/4 turn counterclockwise. 1. Push tab towards the light and remove light assembly. 3. Pull bulb from socket.
434 MAINTAINING YOUR VEHICLE Center High-Mounted Stoplight 1. Remove two screws securing stoplight housing assembly to the liftgate. 2. Turn socket 1/4 counterclockwise and free from housing. 3. Pull bulb straight from socket to remove.
MAINTAINING YOUR VEHICLE Fog Lights 435 2. Remove the far left air dam screw at the bottom of the fascia. 3. Peel back the liner and access the fog light. 4. Rotate the socket and connector 1/4 turn counterclockwise and pull straight reward to disengage from the light. 5. Remove the bulb from the socket and replace. The right fog light can be accessed from below the vehicle. Follow the previous Steps 4 and 5 of the left fog light to replace the bulb.
436 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES U.S. Metric 27 gal 27 gal 102 L 102 L 6 qts 7 qts 5.7 L 6.6 L 14.2 qts 13.5 L 16.6 qts 15.8 L Fuel 4.7L, 87 Octane 5.7L, 89 Octane Engine Oil (with filter) 4.7L, SAE 5W-20, API Certified 5.7L, SAE 5W-20, API Certified Cooling System (includes 2.1 qts/2 L for coolant bottle 4.7L (Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula) 5.7L (Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula) NOTE: All fluid capacities are approximate.
MAINTAINING YOUR VEHICLE 437 FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant 4.7L/5.7L Engine Oil Engine Oil Filter Spark Plugs (4.7L Engine) Spark Plugs (5.7L Engine) Fuel Selection (4.7L Engine) Fuel Selection (5.7L Engine) Fluids, Lubricants and Genuine Parts Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology). Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of DaimlerChrysler Material Standard MS-6395.
438 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Transfer Case Front Axle Rear Axle Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopart ATF+4, Automatic Transmission Fluid. Mopart ATF+4, Automatic Transmission Fluid. SAE 75W-90 Multipurpose Type, GL-5 Gear Lubricant or equivalent. SAE 75W-140 Synthetic Gear Lubricant or equivalent. Mopart DOT 3 and SAE J1703 should be used or equivalent.
MAINTENANCE SCHEDULES CONTENTS m Emission Control System Maintenance . . . . . . . . 440 m Maintenance Schedule . . . . . . . . . . . . . . . . . . . 440 ▫ Required Maintenance Intervals . . . . . . . . . . .
M A I N T E N A N C E 440 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type on the following pages, must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and S reliability.
MAINTENANCE SCHEDULES oil if it has been 6 months since your last oil change even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 mi (10 000 km) or 6 months, whichever comes first. Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change.
M A I N T E N A N C E S C H E D U L E S 8 442 MAINTENANCE SCHEDULES • Check all lights and other electrical items for correct operation. At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines. CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle. Required Maintenance Intervals NOTE: ** Vehicles built with the 4.
MAINTENANCE SCHEDULES 443 M Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Change the engine oil and engine oil filter. Rotate tires. If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. Inspect the brake linings; replace if necessary.
M 444 MAINTENANCE SCHEDULES A I N T E N Maintenance Items A N Replace the engine air cleaner filter. C Inspect the transfer case fluid. E S C H E D U L E S 8 Replace the top row of spark plugs on 4.7L engines. ** Replace the spark plugs on 3.7L and 5.7L engines. Change the automatic transmission fluid & filter if using your vehicle for any of the following: police, taxi, fleet or frequent trailer towing.
MAINTENANCE SCHEDULES 445 M Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Change the automatic transmission fluid & filter. Replace accessory drive belt(s). WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449 ▫ In Mexico Contact . . . . . . . . . . . . . . . . . . . . . 450 ▫ Prepare For The Appointment . . . . . . . . . . . . 449 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . . 451 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 449 ▫ Service Contract . . . . . . . . . . . . . . . . . . . .
448 IF YOU NEED CONSUMER ASSISTANCE m Publication Order Forms . . . . . . . . . . . . . . . . . . 453 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . 455 m Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 455 ▫ Temperature Grades . . . . . . . . . . . . . . . . . . . 456 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
450 IF YOU NEED CONSUMER ASSISTANCE special tools, and the latest information to ensure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your authorized dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealership. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance for the Hearing or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
452 IF YOU NEED CONSUMER ASSISTANCE WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain, or emit, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WARRANTY INFORMATION (U.S.
IF YOU NEED CONSUMER ASSISTANCE 453 To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov. PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below.
454 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-bystep troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.
IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle. All passenger car tires must conform to Federal safety requirements in addition to these grades.
456 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
458 INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . 205,290 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 336 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 155 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 394 Air Conditioner Maintenance . . . . . . . . . . . . 249,398 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 249 Air Conditioning, Operating Tips . . . . . . . . . . . . 261 Air Conditioning, Rear Zone . . . . . . . . . . . . .
INDEX Gear Ranges . . . . . . . . . . . Special Additives . . . . . . . Torque Converter . . . . . . . Axle Fluid . . . . . . . . . . . . . . Axle Lubrication (Axle Fluid) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275 412 279 438 413 Ball Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399 Battery . . . . . . . . . . . . . . . . . . . . . . . . . .
460 INDEX Caps, Filler Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336 Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . . . 392 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 398 Radiator (Coolant Pressure) . . . . . . . . . . . . . . . 405 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415 Carbon Monoxide Warning . . . . . . . . . . . . . . . 75,335 Cargo Management System . . . . . . . . . . . . . . . . . 194 Cargo Organizer . . .
INDEX Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . 402 Adding Coolant (Antifreeze) . . . . . . . . . . . . . . 404 Coolant Capacity . . . . . . . . . . . . . . . . . . . . . . 436 Coolant Level . . . . . . . . . . . . . . . . . . . . . . 402,406 Disposal of Used Coolant . . . . . . . . . . . . . . . . 406 Drain, Flush, and Refill . . . . . . . . . . . . . . . . . . 403 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . 406 Points to Remember . . . . . . . . . . . . . . . .
462 INDEX Driving Through Flowing, Rising, or Shallow Standing Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286 DVD Player (Video Entertainment System) . . . . . . 246 E-85 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338 Electric Remote Mirrors . . . . . . . . . . . . . . . . . . . . 86 Electrical Power Outlets . . . . . . . . . . . . . . . . . . . 185 Electronic Brake Control System . . . . . . . . . . . . . 294 Anti-Lock Brake System . . . . . . . . . . . . . . .
INDEX Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 390,436,437 Oil Filler Cap . . . . . . . . . . . . . . . . . . . 384,385,392 Oil Selection . . . . . . . . . . . . . . . . . . . . . . . 391,436 Oil Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . 392 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271 Temperature Gauge . . . . . . . . . . . . . . . . . . . . . 203 Entry System, Illuminated . . . . . . . . . . . . . . . . . . 20 Equipment Identification Plate . .
464 INDEX Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 398 Transfer Case . . . . . . . . . . . . . . . . . . . . . . . . . 413 Fluids, Lubricants and Genuine Parts . . . . . . . . . . 437 Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 148,435 Folding Rear Seat . . . . . . . . . . . . . . . . . . . . . 129,133 Four Wheel Drive . . . . . . . . . . . . . . . . . . . . . . . 280 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 280 Four-Way Hazard Flasher . . .
INDEX Glass Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 418 Gross Axle Weight Rating . . . . . . . . . . . . . . . 343,346 Gross Cargo Weight . . . . . . . . . . . . . . . . . . . . . . 342 Gross Vehicle Weight Rating . . . . . . . . . . . . . . . . 345 GVWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342,345 Hands-Free Phone (UConnect™) . . . . . . . . 88,220,221 Hard Drive (HDD) . . . . . . . . . . . . . . . . . . . .
466 INDEX Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . 64,65 Inflation Pressure Tires . . . . . . . . . . . . . . . . . . . . 321 Information Center . . . . . . . . . . . . . . . . . . . . . . 167 Information Center, Vehicle . . . . . . . . . . . . . . . . . 167 Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . . 84 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . . 203 Instrument Panel and Controls . . . . . . . . . . . . . .
INDEX Back-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431 Brake Warning . . . . . . . . . . . . . . . . . . . . . . . . 209 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 429 Center Mounted Stop . . . . . . . . . . . . . . . . . . . 434 Courtesy/Reading . . . . . . . . . . . . . . . . . . . . . 166 Cruise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214 Daytime Running . . . . . . . . . . . . . . . . . . . . . . 148 Dome . . . . . . . . . . . . . . . . . . . .
468 INDEX Power Door . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Steering Wheel . . . . . . . . . . . . . . . . . . . . . . . . . 17 Lower Anchors and Tether for CHildren (LATCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . 400 Lug Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374 Luggage Carrier . . . . . . . . . . . . . . . . . . . . . . . . . 192 Lumbar Support . . . . . . . . . . . . . . . .
INDEX Octane Rating, Gasoline (Fuel) . . . . . . . . . . . . . . 331 Oil Change Indicator . . . . . . . . . . . . . . . . . . 169,207 Oil Change Indicator, Reset . . . . . . . . . . . . . . . . . 207 Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . 390,437 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436 Change Interval . . . . . . . . . . . . . . . . . . . . . . . 391 Dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390 Disposal . . . . . . . . . . . . .
470 INDEX USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217,220 Positive Crankcase Valve . . . . . . . . . . . . . . . . . . 408 Power Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408 Distribution Center (Fuses) . . . . . . . . . . 384,385,423 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . 20,30 Lift Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Rearview Mirrors . . . . . . . . . . . . . . . . . . . . . . . . 84 Reclining Front Seats . . . . . . . . . . . . . . . . . . . . . 121 Recorder, Event Data . . . . . . . . . . . . . . . . . . . . . . 62 Recreational Towing . . . . . . . . . . . . . . . . . . . . . . 360 Shifting into Transfer Case Neutral (N) . . . . . . . 361 Shifting out of Transfer Case Neutral (N) . . . . . 362 Reformulated Gasoline . . . . . . . . . . . . . . . . . . . . 332 Refrigerant . . . . . . . . . . . . . . . . . . . . .
472 INDEX Child Restraint . . . . . . . . . . . . . . . . . . . . . . . 64,66 Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Front Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Cleaning .
INDEX Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322 Sound Systems (Radio) . . . . . . . . . . . . . . . . . 217,220 Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316 Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394 Speed Control (Cruise Control) . . . . . . . . . . . . . . 156 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
474 INDEX Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . 303 Tire Safety Information . . . . . . . . . . . . . . . . . . . . 303 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77,312,455 Aging (Life of Tires) . . . . . . . . . . . . . . . . . . . . 318 Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 312 Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . 320 Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 Changing . . .
INDEX Towing Assistance . . . . . . . . . . . . . . . . . . . . . . . 101 Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286 Traction Control . . . . . . . . . . . . . . . . . . . . . . 208,297 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . 345 Cooling System Tips . . . . . . . . . . . . . . . . . . . . 358 Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 Minimum Requirements . . . . . . . . . . . . . . . . . 352 Trailer and Tongue Weight . . .
476 INDEX Transmitter Programming (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . 318 Trip Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . 208 Trip Odometer Reset Button . . . . . . . . . . . . . . . . 214 Turn Signals . . . . . . . . . . . . . . . . . . . . . . 149,203,431 UCI Connector . . . . . . . . . . . . . . . . . . . . . . . . . 241 UConnect™ (Hands-Free Phone) . . . . . . . . . .
INDEX Weight Load Carrying . . . . . . . . . . . . . . . . . . . . 342 Wheel Alignment and Balance . . . . . . . . . . . . . . . 320 Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . . 416 Wheel and Wheel Trim Care . . . . . . . . . . . . . . . . 416 Wheel Changing . . . . . . . . . . . . . . . . . . . . . . . . 369 Wheel Mounting . . . . . . . . . . . . . . . . . . . . . . . . 370 Wheel Nut Torque . . . . . . . . . . . . . . . . . . . . . . . 374 Wind Buffeting . . . . . . . . . . . . . . . . . .
2008 Aspen 2008 OWNER’ S MANUAL 81-026-0850 First Edition Printed in U.S.A.
