TABLE OF CONTENTS SECTION PAGE .............................................................3 1 1 INTRODUCTION 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4 UNDERSTANDING YOUR INSTRUMENT PANEL 5 STARTING AND OPERATING 6 WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .335 6 7 MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS m Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m Vehicle Identification Number . . . . . . . . . . . . . . . 6 m How To Use This Manual . . . . . . . . . . . . . . . . . . 4 m Vehicle Modifications / Alterations . . . . . . . . . . . 7 m Warnings And Cautions . . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures, which could result in an accident or bodily injury. It also contains CAUTIONS against procedures, which could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER The vehicle identification number (VIN) is on the left front corner of the instrument panel.
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . . .12 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . . .19 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .12 ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .19 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .14 m Illuminated Entry System — If Equipped . . . . . . .20 m Sentry Keyt . . . . . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .25 m Trunk Safety Warning . . . . . . . . . . . . . . . . . . . . .38 ▫ Programming Additional Transmitters . . . . . . . .26 ▫ Trunk Emergency Release . . . . . . . . . . . . . . . .38 ▫ Battery Replacement . . . . . . . . . . . . . . . . . . . .26 m Occupant Restraints . . . . . . . . . . . . . . . . . . . . . .39 ▫ General Information . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .62 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . .74 m Engine Break-In Recommendations . . . . . . . . . . .72 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 m Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 ▫ Transporting Passengers . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS You can insert the double-sided keys into the locks with either side up. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place. Ignition Key Removal Place the selector lever in PARK.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 system will trap the key in the ignition switch lock cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped, but the key cannot be removed until you obtain service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE details, refer to “Key-Off Power Delay,” under “Personal Settings (Customer Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. WARNING! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SENTRY KEYT The Sentry Keyt Immobilizer System prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses ignition keys, which have an embedded electronic chip (transponder), to prevent unauthorized vehicle operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • The Sentry Keyt Immobilizer System is not compatible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sentry KeyT Programming You can program new keys to the system if you have two valid sentry keys by performing the following procedure: 1. Cut the additional Sentry Keyt Transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the ignition switch. Turn the ignition switch to the position for at least three seconds, but no longer than 15 seconds.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE vehicle. The remaining keys must then be reprogrammed. All vehicle keys must be taken to the dealer at the time of service to be reprogrammed. General Information The Sentry Keyt system complies with FCC rules part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Arm the System: 1. Remove the keys from the ignition switch and exit the vehicle. 2. Lock the doors by pressing the power door lock switch or the LOCK button on the Remote Keyless Entry (RKE) transmitter. NOTE: The system will not arm if you lock the doors with the manual door lock plungers. 3. Close all doors. The VSA Indicator Light in the instrument cluster will flash rapidly for 16 seconds. This shows that the system is arming.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • When the system is armed, the interior power door lock switches will not unlock the doors. The VSA system is designed to protect your vehicle; however, you can create conditions where the system will give you a false alarm. If one of the previously described arming sequences has occurred, the system will arm regardless of whether you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 The interior lights will fade to off after about 30 seconds or they will immediately fade to off once the ignition switch is turned on. 2 NOTE: • The illuminated entry system will not operate the interior lights if the dimmer control is in the “defeat” position (extreme downward position).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Key Unlock, Driver Door/All Doors First This feature lets you program the system to unlock either the driver’s door or both doors on the first press of the UNLOCK button on the transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to “Flash Lights with Lock,” under 9Personal Settings (Customer Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual for details. • For vehicles not equipped with the EVIC, perform the following procedure: 1. Press and hold the UNLOCK button on a programmed transmitter for at least four seconds, but not longer than 10 seconds.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To lock the doors: Press and release the LOCK button on the transmitter to lock both doors. The turn signal lights will flash and the horn will chirp once to acknowledge the lock signal. 1. Press the LOCK button on a programmed transmitter for at least 4 seconds, but not longer than 10 seconds. Then, press the PANIC button while still holding the LOCK button.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Convertible Top Operation Refer to “Convertible Top Operation” under “Understanding The Features Of Your Vehicle” in Section 2 of this manual. To Unlatch the Trunk: Press the TRUNK button on the transmitter two times to unlatch the trunk. Express Down Window Feature This feature allows you to remotely lower both door and rear quarter windows at the same time.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Programming Additional Transmitters Refer to SENTRY KEYt “Customer Key Programming.” If you do not have a programmed transmitter, contact your dealer for details. Battery Replacement The recommended replacement battery is CR2032. NOTE: • Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. • Do not touch the battery terminals that are on the back housing or the printed circuit board. 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. REMOTE STARTING SYSTEM — IF EQUIPPED This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conveniently from outside the vehicle while still maintaining security. The system has a targeted range up to 35 ft. (11 m). 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The vehicle must be equipped with an automatic transaxle to be equipped with Remote Start. How To Use Remote Start All of the following conditions must be met before the engine will remote start: • Gear selector lever in PARK. • Doors closed. • Hood closed. • Trunk closed. • Hazard switch off. • Brake switch inactive (brake pedal not pressed). • Ignition key removed from ignition switch. • Battery at an acceptable charge level.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Exit Remote Start Mode & Drive the Vehicle Before the end of the 15 minute cycle, press and release the UNLOCK button on the RKE transmitter to unlock the doors and disarm the Vehicle Security Alarm (if equipped). Then, within 15 minutes, insert the key into the ignition switch and turn the switch to the ON position. NOTE: The ignition switch must be in the ON position in order to drive the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. Power Door Locks A door lock switch is located on the driver and passenger door trim panel. Press this switch to lock or unlock the doors. • When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Door Locks The Auto Door Locks feature can be enabled or disabled by your authorized dealer. See your dealer for programming. Automatic Unlock Doors on Exit The doors will unlock automatically on vehicles with power door locks if: 1. The Auto Unlock on Exit feature is enabled. 2. The transaxle was in gear and the vehicle speed returned to 0 mph (0 km/h). 3. The transaxle is in NEUTRAL or PARK. 4. The driver door is opened. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. A single chime will indicate the completion of the programming. 5. Repeat these steps if you want to return this feature to its previous setting. NOTE: Use the Auto Unlock on Exit feature in accordance with local laws. WINDOWS Power Windows The window controls on the driver’s door trim panel operate the door windows and the rear quarter windows.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There is a single window control on the passenger’s door trim panel, which operates the passenger door window. The window controls will operate when the ignition switch is turned to the ON or ACC position, and when the accessory delay feature is active. NOTE: • The door window will lower slightly if it is closed completely when opening the door. The window will return to its fully closed position after closing the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To open the window part way, push the window switch to the first detent and release it when you want the window to stop. To cancel the Auto Down movement, operate the switch either in the up or down direction and release the switch. For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power window switches will remain active for 45 seconds after the ignition switch is turned to the LOCK position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: ANTI-PINCH PROTECTION • If the window runs into any obstacle during autoclosure, it will reverse direction and then stop. Remove the obstacle and use the window switch again to close the window. • Any impact due to rough road conditions may trigger the auto reverse function unexpectedly during autoclosure. If this happens, pull the switch lightly to the first detent and hold to close window manually.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE passenger door, press and release the window lock button (setting it in the down position). To enable the window control, press and release the window lock button again (setting it in the up position). Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with one window down in certain open or partially open positions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The following conditions must be met in order for this switch to operate: • The gear selector lever must be in PARK. • The convertible top must be either closed and latched or open and latched. 37 To unlatch the trunk lid from outside the vehicle, press and release the TRUNK button on the Remote Keyless Entry (RKE) transmitter two times. With the ignition ON, the word “deck” will display in the odometer indicating the trunk is open.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK SAFETY WARNING Trunk Emergency Release WARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat. If trapped in the trunk, children can die from suffocation or heat stroke.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 inside the trunk, the trunk can be simply opened by pulling on the glow-in-the-dark handle attached to the trunk latching mechanism. See picture. • An energy absorbing steering column and steering wheel. OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. The following safety features are standard on your vehicle: • Supplemental front seat side mounted head airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The front airbags have a dual-stage inflator design. This allows the airbag to have different rates of inflation that are based on collision severity. Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Inserting Latch Plate Into Buckle WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, lift up on the shoulder belt and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. 43 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE BeltAlertt Programming The Enhanced Warning System (BeltAlertt) can be enabled or disabled by your authorized dealer or by performing the following steps: 3. Within 60 seconds of turning the ignition switch to the ON position, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled. NOTE: DaimlerChrysler does not recommend deactivating the Enhanced Warning System (BeltAlertt).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Locking Mode In this mode, the shoulder belt is automatically prelocked. However, the belt will still retract to remove any slack in the shoulder belt. The Automatic Locking Mode is available on all passenger-seating positions. Use the Automatic Locking Mode anytime a child safety seat is installed in a passenger seating position. Children 12 years old and under should be properly restrained in the rear seat whenever possible.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Extender If a seat belt is too short, even when fully extended, your dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough. When it is not required, remove the extender, and stow it. WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 WARNING! • Do not put anything on or around the front airbag covers or attempt to open them manually. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Along with seat belts and pretensioners, front airbags work with the knee bolsters to provide improved protection for the driver and front passenger. Seat airbags also work with seat belts to improve occupant protection. Infants in rear facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag. An airbag deployment can cause severe injury or death to infants in that position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should wear their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4. If your vehicle has seat airbags, do not lean against the door, airbags will inflate forcefully into the space between you and the door. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag System Components The airbag system consists of the following: • Occupant Restraint Controller (ORC) • AIRBAG Warning Light • Driver Airbag • Front Passenger Airbag • Supplemental seat side (Thorax) and head airbags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Driver Airbag Special Features Driver airbag deployment and force level is controlled by the driver’s seat position as well as impact severity. Use of special inflators, result in a very compact driver’s airbag. In addition to the small size, the inflating gasses exit through strategically placed vents, which direct the gas away from the occupant.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC also turns on the AIRBAG warning light in the instrument panel for six to eight seconds for a self-check when the ignition is first turned on. After the self-check, the AIRBAG warning light will turn off. If the ORC detects a malfunction in any part of the system, it turns on the AIRBAG warning light either momentarily or continuously. A single chime will sound if the light comes on again after initial start up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 When the bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each bag deploys independently, that is a left side impact deploys the left bag only and a right-side impact deploys only the right bag. The following requirements must be strictly adhered to: • Do not make any modifications to the front seat components, assembly, or to the seat cover in any way.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Do not add a secondary seat cover other than those approved by DaimlerChrysler/Mopar.t • At no time should any Supplemental Restraint System (SRS) component or SRS related component or fastener be modified or replaced with any part except those which are approved by DaimlerChrysler/ Mopar.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the airbags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Accident Response System In the event of an impact that causes airbag deployment, with the vehicle stopped, and the vehicle communication network intact, and the power intact, the Enhanced Accident Response System performs the following functions: • Cuts off fuel to the engine. • Flashes hazard lights. • Turns on the interior lights, which remain on as long as the battery has power or until the ignition key is removed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Do not attempt to modify any part of your advanced airbag system. The airbag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any advanced airbag system service. If your seat including your trim cover and cushion needs to be serviced in any way (including removal or loosening/ tightening of seat attachment bolts), take the vehicle to your authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE fuses. Refer to “Fuses” in this manual for fuse location information. See your authorized dealer for service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE provided to the custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the US government and various states. Data of a potentially sensitive nature, such as would identify a particular driver, vehicle, or crash, will be treated confidentially.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Cruise control status. • Traction/stability control status. • Tire pressure monitoring system status – If Equipped. Child Restraint Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants and Child Restraints 63 “LATCH — Child Seat Anchorage System (Lower Anchors and Tether for CHildren)” in this section. • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and 9convertible9 child seats.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s cushion while the child’s back is against the seat back, then the child should use a Belt Positioning Booster Seat. The child and booster seat are held in the vehicle by the lap/shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 WARNING! Here are some tips on getting the most out of your child restraint: • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • All passenger seating positions contain automatic locking retractors. However, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary. • Buckle the child into the seat according to the child restraint manufacturer’s directions. • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Do not leave it loose in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles. Rear Seat LATCH Anchors Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child 67 restraint systems having attachments for those anchorages will continue to have features for installation in vehicles using the lap or lap/shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave your child unattended in the vehicle. Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seat cover material. Then rotate the tether anchorage cover directly behind the seat where you are placing the child restraint and attach the tether strap to the anchorage, being careful to route the tether strap to provide the most direct path between the anchor and the child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The seat belt must be in the Automatic Locking Mode in order to enable a child restraint to be tightly installed. Refer to “Automatic Locking Mode” in this section for details. A locking clip should not be necessary once the automatic locking feature is enabled. Position the shoulder and lap belt on the child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 4. Open the access cover (C) on the carpet covering the back of the seat and attach the tether strap hook (D) to the anchor. Child Tether Access Port Cover 3. Push the tether strap and hook (B) through the access port and down into the trunk. NOTE: Route the tether strap to provide the most direct path from the child seat to the anchor. Child Tether Anchor 5. Remove slack in the tether strap according to the child restraint manufacturer’s instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The recommended viscosity and quality grades are shown in Section 7 of this manual. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED. A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty. SAFETY TIPS Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel. Door Latches Check for positive closing, latching, and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 m Convertible Top Operation . . . . . . . . . . . . . . . . .81 m Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 ▫ Power Convertible Top Usage Precautions . . . . .82 ▫ Automatic Dimming Mirror . . . . . . . . . . . . . . .96 ▫ Cargo Protector . . . . . . . . . . . . . . . . . . . . . . . .85 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . .97 ▫ Power Convertible Top Controls . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Phone Call Features . . . . . . . . . . . . . . . . . . . 108 ▫ Power Seats — If Equipped . . . . . . . . . . . . . . 134 ▫ UConnectt System Features . . . . . . . . . . . . . . 110 ▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . . 135 ▫ Advanced Phone Connectivity . . . . . . . . . . . . 115 ▫ Heated Seats — If Equipped . . . . . . . . . . . . . 135 ▫ Things You Should Know About Your UConnectt System . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . 141 m Electronic Speed Control — If Equipped . . . . . . 151 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . 142 ▫ Electronic Speed Control Operation . . . . . . . . 151 ▫ Highbeam/Lowbeam Select Switch . . . . . . . . . 142 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . . 151 ▫ Flash To Pass . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 m Cup Holders . . . . . . . . . . . . . . . . . . . . . . . . . . 164 ▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . . . 160 ▫ Front Seat Cup Holder . . . . . . . . . . . . . . . . . 164 ▫ General Information . . . . . . . . . . . . . . . . . . . 161 ▫ Heated Or Cooled Cup Holder — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 164 m Electrical Power Outlets .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONVERTIBLE TOP OPERATION WARNING! The convertible top does not provide the structural protection that a reinforced metal roof does and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision. Therefore, it is important that all occupants wear their seat belts at all times when riding in a convertible.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When raising the top, the system retracts the hard tonneau cover back into its stowage area underneath the trunk lid. To complete either operation, the trunk lid returns to its normal position and then latches. Spring-loaded flipper doors, which provide clearance for the linkage, close off notches in the quarter trim panels when the top is up.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Correctly position the cargo protector in the trunk before stowing the top. Doing so closes a switch that allows top operation (stowing) to proceed. If the switch is not closed, a warning message displays in the instrument cluster to notify the driver. • Always place items carefully into the trunk. • Do not push items too far into the trunk, particularly when the top is retracted into its stowage area in the trunk.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! • Do not operate the Power Top when the vehicle is in motion. • Before operating the Power Top, make sure that no moving parts of the convertible top can injure a person or animal. • Do not operate the Power Top with the hydraulic pump valve open. • Do not allow the top to remain in the suspended position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Protector The cargo protector is located in the trunk. Before lowering the convertible top, you must unfold the cargo protector and seat the tabs at each end of the cargo protector in the V slots in the trunk liner. Doing so closes a switch that allows top operation. If the switch is not closed, a warning message displays in the instrument cluster to notify the driver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Convertible Top Controls The Power Top switch is located on the instrument panel to the left of the steering column. There is also a Power Top button on the Remote Keyless Entry (RKE) Transmitter for remotely lowering the power convertible top.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Lowering the Power Convertible Top Using the Remote Keyless Entry (RKE) Transmitter Using the Power Top Switch 1. Press and release the Unlock button. 2. Press, release, then press, and hold the Power Top button down until the operation of lowering the top and all four windows to their fully retracted positions is complete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press and hold the switch in the Top Up position until the operation of raising the top and latching it is complete, which is indicated by the system raising the windows and displaying “TOP DONE” in the odometer or “CONVERTIBLE TOP COMPLETE” in the EVIC (if equipped). Using the Remote Keyless Entry (RKE) Transmitter You cannot use the Power Top button on the RKE transmitter to raise the power convertible top.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 NOTE: It is recommended that you lower the convertible top before installing or removing the Wind Stop. Installing the Wind Stop 1. Remove the Wind Stop from the trunk. 2. Unfold the Wind Stop framework. 3. Lay the small frame (1) flat on top of the large frame (2) and snap the two frames together by engaging the frame lock (3). NOTE: The frames must lie flat on each other in order to snap them together.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Pivot the small frame (1) away from the large frame (2) until the pivot lock (3) engages to lock the two frames in an L shape. 5. Unfold both stems at the rear of the large frame.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Align and insert the stems into the slot in each trim panel. 91 7. Align the pins at the front of the large frame with the hole in each trim panel. Slide the pins outward until fully extended into each hole.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Removing & Storing the Wind Stop Reverse the installation procedure to remove, fold, and store the Wind Stop. However, note the following before doing so: • Disengage the pivot lock (1) to fold the small frame flat onto the large frame. Disengage the frame lock (2) to disconnect the small frame from the large frame.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE EVIC MessageL EVIC Message Display TimeL CONVERT- Until OpIBLE TOP IN eration is OPERATION Complete CONVERT- 9 Seconds IBLE TOP COMPLETE SECURE CARGO SHIELD 9 Seconds CONVERT- Until OpIBLE TOP IN eration is OPERATION Complete Odometer Message (< 5 mph [8 km/h])LL TOP Odometer Message (> 5 mph [8 km/h])LL — Odometer Message Display TimeLL — Chime Condition Operator Action Required — — — — Single Chime SET CARGO Display Scrolls — SHIELD for 9 Seconds
UNDERSTANDING THE FEATURES OF YOUR VEHICLE EVIC MessageL EVIC Message Display TimeL SPEED TOO 9 Seconds HIGH Odometer Message (< 5 mph [8 km/h])LL SPEED TOO HIGH Odometer Message Display TimeLL Display Scrolls for 9 Seconds Odometer Message (> 5 mph [8 km/h])LL TOP Odometer Message Display TimeLL 6 Seconds TRUNK AJAR Continuous DECK Continuous DECK CONVERTIBLE TOP MALFUNCTION CONVERTIBLE TOP MALFUNCTION 6 Seconds TOP FAIL Display Scrolls TOP for 6 Seconds 6 Seconds Until Fault TOP FAIL
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 L If so equipped. LL For vehicles not equipped with the EVIC. LLL The PTCM will LOCKOUT the power convertible top system if the vehicle charging system is malfunctioning, or the battery is run down, or the hydraulic pump is overheating. In addition, the system prohibits lowering the top when ambient temperature is at 0°F (-18°C) or lower and raising the top when ambient temperature is below -40°F (-40°C).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Automatic Dimming Mirror This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light will illuminate to indicate when the dimming feature is activated.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 CAUTION! WARNING! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Remote Control Mirrors The power mirror switch is located on the driver’s door trim. A rotary knob selects the left mirror, right mirror, or off position. After selecting a mirror, move the knob in the same direction you want the mirror to move. When finished, return the knob to the center “O” (Off) position to guard against accidentally moving a mirror position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Heated Remote Control Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the Rear Window Defrost. { “248-555-12129). Your cellular phone’s audio is transmitted through your vehicle’s audio system; the system will automatically mute your radio when using the UConnectt system. Vanity Mirror — If Equipped A vanity mirror is attached to the inside face of the sun visor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnectt allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The UConnectt phonebook enables you to store up to 32 names, with four numbers per name. Each language has a separate 32-name phonebook accessible only in that language. This system is driven through your Bluetootht Hands-Free profile cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnectt system is fully integrated with the vehicle’s audio system. The volume of the UConnectt system can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the UConnectt system such as 9CELL9 or caller ID on certain radios.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say 9Help9 following the beep. The UConnectt system will play all the options at any prompt if you ask for help. To activate the UConnectt system from idle, simply press the PHONE button and follow audible prompts for directions. All UConnectt system sessions begin with a press of the PHONE button on the radio control head.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For identification purposes, you will be prompted to give the UConnectt system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between 1 and 7, with 1 being the highest priority. You can pair up to seven cellular phones to your UConnectt system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call by Saying a Name Add Names to Your UConnectt Phonebook • Press the PHONE button to begin. NOTE: Adding names to the phonebook is recommended when the vehicle is not in motion. • After the 9Ready9 prompt and the following beep, say “Call9. • Press the PHONE button to begin. • The system will prompt you to say the name of the person you want to call. • After the 9Ready9 prompt and the following beep, say 9Phonebook New Entry.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE After you are finished adding an entry into the phonebook, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu. The UConnectt system will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Edit Entries in the UConnectt Phonebook NOTE: Editing names in the phonebook is recommended when the vehicle is not in motion. • Press the PHONE button to begin. • After the 9Ready9 prompt and the following beep, say 9Phonebook Edit.9 9Phonebook Edit9 can be used to add another phone number to a name entry that already exists in the phonebook.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE from which you choose. To select one of the entries from the list, press the VOICE RECOGNITION button while the UConnectt system is playing the desired entry and say 9Delete.9 • After you enter the name, the UConnectt system will ask you which designation you wish to delete: home, work, mobile, pager, or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnectt system will then prompt you as to the number designation you wish to call. • The selected number will be dialed. Phone Call Features The following features can be accessed through the UConnectt system if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the UConnectt system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 or 9Call9 followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to 9Toggling Between Calls.9 To combine two calls, refer to 9Conference Call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE hold may not become active automatically. This is cell phone-dependent. To bring the call back from hold, press and hold the PHONE button until you hear a single beep. Redial • Press the PHONE button to begin. • After the 9Ready9 prompt and the following beep, say 9Redial.9 • The UConnectt system will call the last number that was dialed from your cellular phone. NOTE: This may not be the last number dialed from the UConnectt system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 • After the 9Ready9 prompt and the following beep, say the name of the language you wish to switch to (English, Espanol, or Francais, if so equipped). If the phone is not reachable and the UConnectt system is operational, you may reach the emergency number as follows: • Continue to follow the system prompts to complete language selection. • Press the PHONE button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your phone must be turned on and paired to the UConnectt system to allow use of this vehicle feature in emergency situations, when the cell phone has network coverage and stays paired to the UConnectt system. Towing Assistance If you need towing assistance: • Press the PHONE button to begin. • After the 9Ready9 prompt and the following beep, say 9Towing Assistance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When calling a number with your UConnectt system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can press the VOICE RECOGNITION button and say the sequence you wish to enter, followed by the word 9Send.9 For example, if required to enter your PIN number followed with a pound, 3 7 4 6 #, you can press the VOICE RECOGNITION button and say, 93 7 4 6 # Send.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g., the UConnectt system will not repeat a phone number before you dial it). • Press the PHONE button to begin. • After the 9Ready9 prompt and the following beep, say 9Setup Confirmations.9 The UConnectt system will play the current confirmation prompt status and you will be given the choice to change it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mute/Un-Mute (Mute Off) When you mute the UConnectt system, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the UConnectt system: • Press the VOICE RECOGNITION button. • Following the beep, say 9Mute.9 In order to un-mute the UConnectt system: • Press the VOICE RECOGNITION button. • Following the beep, say 9Mute off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnectt system will play the phone names of all paired cellular phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the VOICE RECOGNITION button and say “Select” or “Delete.” Also, see the next two sections for an alternate way to “select” or “delete” a paired phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Things You Should Know About Your UConnectT System UConnectt Tutorial To hear a brief tutorial of the system features, press the PHONE button and say “UConnectt Tutorial.” Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers, the UConnectt system Voice Training feature may be used. To enter this training mode, follow one of the two following procedures: From outside the UConnectt mode (e.g.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Speak normally, without pausing, just as you would speak to a person sitting a few feet/meters away from you. • When navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say 9Send.9 • Make sure that no one other than you is speaking during a voice recognition period. • Storing names in phonebook when the vehicle is not in motion is recommended.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 • In a convertible vehicle, system performance may be compromised with the convertible top down. • Echo at the far end can sometimes be reduced by lowering the in-vehicle audio volume. Far End Audio Performance • In a convertible vehicle, system performance may be compromised with the convertible top down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home 123 3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call UConnectt Tutorial try again voice training work yes
UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. 125 possible.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you ever wish to interrupt the system while it lists options, press the VR hard-key, listen for the beep, and say your command. The system will best recognize your speech if the windows are closed, and the heater/air-conditioning fan is set to low. Pressing the VR hard-key while the system is speaking is known as “barging in.” The system will be interrupted and you can add or change commands. This will become helpful once you start to learn the options.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the voice recognition system is speaking. Please note the volume setting for VR is different then the audio system. • NEXT STATION (to select the next station) Main Menu Start a dialogue by pressing the VR hard-key. You may say MAIN MENU to switch to the main menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Satellite Radio To switch to satellite radio mode say SAT or SATELLITE RADIO.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE − CONTINUE (to continue recording) − DELETE (to delete the recording) • PLAY MEMOS (to play previously recorded memos) — During the playback you may press the VR hardkey to stop playing memos.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Manual Front Seat Adjustments Forward & Rearward Adjustment — If Equipped The manual seat adjustment bar is at the front of the seat, near the floor. Pull the bar upward to move the seat forward or rearward. Release the bar once the seat is in the position desired. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. Recliner Adjustment The recliner control is on the outboard side of the seat. To recline the seat, lean forward slightly and lift the lever. Then lean back to the position desired and release the lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. inboard side of the seat. Turn the control lever downward to increase and upward to decrease the desired amount of lumbar support.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Easy Entry System The Easy Entry lever is located on upper seat belt anchor cover. 133 On the passenger seat, pull the lever upward to move the seat and seatback forward. When returning the seat to its normal position, the memory feature restores the seat position and seatback recline position to their current settings. On the driver seat, pull the lever upward to move the seatback forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Seats — If Equipped The power seat switch is on the outboard side of the seat near the floor. Use the switch to move the seat up, down, forward, rearward, or to tilt the seat. CAUTION! Do not place any article under any seat as it may cause damage to the seat controls. WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjust the restraint so that the upper edge is as high as practical. To raise it, pull upward on the head restraint. To lower it, depress the button on the post guide and push downward on the head restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods. Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood. First, pull the hood release lever located under the left side of the instrument panel. 137 Next, move to the outside of the vehicle and lift the secondary latch underneath the center front edge of the hood. Then, raise the hood.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole on the underside of the hood. slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights & Parking Lights Turn the end of the Multi-Function Control Lever to the first detent for parking light operation. Turn the end of the lever to the second detent for headlight operation. 139 Automatic Headlights — If Equipped This system automatically turns the headlights ON or OFF according to ambient light levels. To turn the system ON, turn the end of the Multi-Function Control Lever to the (A) AUTO position (third detent).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE AUTO position. In addition, the headlights will turn OFF when the wipers are turned off if they were turned on by this feature. The Headlights with Wipers feature can be turned on or off through the Electronic Vehicle Information Center (EVIC) — if equipped. For details, refer to ”Headlights with Wipers,” under “Personal Settings (Customer Programmable Features),” under “Electronic Vehicle Information Center” in Section 4 of this manual.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 the headlight switch is off, the parking brake is off, the turn signal is off, and the selector lever is in any position except “P” (Park). NOTE: The Daytime Running Lights will turn off automatically when the turn signal is in operation and turn on again when the turn signal is not operating.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals Move the Multi-Function Lever upward or downward and the corresponding turn signal indicator on the instrument panel will flash to show proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially upward or downward without moving beyond the detent. Check for a defective outside light bulb if either light remains on and does not flash or has a very fast flash rate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Flash to Pass You can signal another vehicle with your headlights by lightly pulling the Multi-Function Control Lever toward you. This will cause the headlights to turn on at high beam and remain on until the lever is released. NOTE: If the Multi-Function Control Lever is held in the Flash to Pass position for more than 15 seconds, the high beams will shut off. If this occurs, wait 30 seconds before activating the Flash to Pass function again.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights Two courtesy/reading lights are located in the bottom of the rearview mirror. You can turn these lights on and off from the switches in the mirror or from the Dimmer Control in the Multi-Function Lever. These lights are also controlled automatically by the illuminated entry system. A courtesy light is also found in the rear of the center console. You can turn this light on and off from the dimmer control in the Multi-Function Lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Parade Mode (Daytime Brightness Feature) Rotate the Dimmer Control to the first detent to brighten the odometer and radio display when the parking lights or headlights are on during daylight conditions. Interior Light ON Rotate the Dimmer Control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The Windshield Wiper / Washer Control Lever is located on the right side of the steering column. Rotate the end of the lever to the first detent past the intermittent settings for Low-speed wiper operation, or to the second detent past the intermittent settings for High-speed wiper operation. NOTE: The wipers will automatically return to the “Park” position if you turn off the ignition switch while they are operating.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than OFF. • Always remove any buildup of snow that prevents the windshield wiper blades from returning to the OFF position. If the windshield wiper control is turned OFF and the blades cannot return to the OFF position, damage to the wiper motor may occur.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during windshield washer use. Mist Feature Push downward on the Windshield Wiper / Washer Control Lever to activate a single wipe cycle to clear the windshield of road mist or spray from a passing vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE addition, the headlights will turn OFF when the wipers are turned off if they were turned on by this feature. The Headlights with Wipers feature can be turned on or off through the Electronic Vehicle Information Center (EVIC) — if equipped. For details, refer to ”Headlights with Wipers,” under “Personal Settings (Customer Programmable Features),” under “Electronic Vehicle Information Center” in Section 4 of this manual.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 WARNING! Do not adjust the steering wheel while driving. The tilt/telescoping adjustment must be locked while driving. Adjusting the steering wheel while driving or driving without the tilt/telescoping adjustment locked could cause the driver to lose control of the vehicle. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 25 mph (40 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE release the ONOFF button a second time. The CRUISE indicator will turn off. Be sure to turn the system OFF when not in use. NOTE: The Electronic Speed Control System will automatically turn off when the engine is turned off. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Resume Speed: If you deactivated the speed control without erasing the set speed from memory and your vehicle speed is above 20 mph (32 km/h) you can resume the previous set speed. To do so, push the lever up and release RESUME ACCEL, and then remove your foot from the accelerator pedal. To Vary The Speed Setting: When the speed control is set, you can increase speed by pushing up and holding the lever RESUME ACCEL.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing: Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Speed Control On Hills NOTE: The speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without speed control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 GARAGE DOOR OPENER — IF EQUIPPED HomeLinkt replaces up to three remote controls (hand held transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLinkt unit operates off your vehicle’s battery. 3 The HomeLinkt buttons that are located in the headliner or sun visor designate the three different HomeLinkt channels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 It is recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLinkt for more efficient training and accurate transmission of the radio-frequency signal. Watch for the HomeLinkt indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds, or longer in rare cases. The garage door may open & close while you train.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Press and hold the just-trained HomeLinkt button and observe the indicator light. If the indicator light stays on constantly, programming is complete and the garage door (or device) should activate when the HomeLinkt button is pressed. If the indicator light blinks rapidly for two seconds, and then turns to a constant light, continue with programming for Rolling Code. 5.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Return to the vehicle and press the programmed HomeLinkt button twice (holding the button for 2 seconds each time). If the device is plugged in and activates, programming is complete. If the device does not activate, press the button a third time (for 2 seconds) to complete the training. If you are have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then proceed with Step 4 under “Programming HomeLinkt.” earlier in this section. Using HomeLinkT To operate, simply press and release the programmed HomeLinkt button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/office lighting, etc. The hand-held transmitter of the device may also be used at any time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Press the Learn Button on the Garage Door Opener to complete the training for Rolling Code. • Did you unplug the device for training, and remember to plug it back in? If you are have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. General Information This device complies with FCC rules part 15 and Industry Canada RSS-210.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If desired, the instrument panel power outlet can be converted by your authorized dealer to provide power with the ignition switch while in the “LOCK” position. The center console power outlet is powered directly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or prevent engine starting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! For vehicles equipped with the heated and cooled cup holder, locate the cup holder ash receiver in the forward cup holder. The optional ash receiver also comes with a cigar lighter. Use the power outlet either in the cubby bin compartment below the climate controls or in the console’s bottom storage compartment to power this cigar lighter.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE unit is on and the LED is Red, the cup holder is being heated. When the LED is Blue, the cup holder is being cooled. 165 Rear Seat Cup Holders Cup holders for the rear seat occupants are located in the armrests. Each cup holder is capable of holding up to a 20 oz. (1⁄2 liter) bottle or can.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES Storage The center console contains a cubby bin with flip-down cover located below the climate controls. This compartment also contains a 12-volt electrical outlet. WARNING! Do not place ashes inside the cubby bin located on the center console. A fire leading to bodily injury could result. Two separate storage compartments are also located underneath the armrest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 The top compartment holds small items, such as a pen and note pad, while the larger bottom compartment will hold CDs and alike. The bottom compartment also contains a 12-volt power outlet and a molded-in coin holder (designed to hold various size coins). The console’s front opening lid allows for easy access to these compartments.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sliding Armrest — If Equipped On some models, the center console armrest slides forward and rearward for added user comfort.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS m Instrument Panel Features . . . . . . . . . . . . . . . . . 173 ▫ Compass Display . . . . . . . . . . . . . . . . . . . . . 191 m Base Instrument Cluster . . . . . . . . . . . . . . . . . . 174 ▫ Personal Settings (Customer Programmable Features) . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 m Premium Instrument Cluster . . . . . . . . . . . . . . . 175 m Instrument Cluster Descriptions . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ FM Reception . . . . . . . . . . . . . . . . . . . . . . . . 197 m Sales Code REQ — AM/FM Stereo Radio And 6–Disc CD/DVD Changer (MP3/WMA AUX Jack) . . . . . . . . . . . . . . . . . . 198 ▫ Operating Instructions — Voice Recognition System (VR) (If Equipped) . . . . . . . . . . . . . . . 214 ▫ Operating Instructions — Hands-Free Communication (UConnect™) (If Equipped) . . 215 ▫ Operating Instructions - Radio Mode . . . . . . . 199 ▫ Clock Setting Procedure . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 222 ▫ List Or Browse Mode . . . . . . . . . . . . . . . . . . 223 m Satellite Radio (RSC) — If Equipped (RER/REQ/REN Radios Only) . . . . . . . . . . . . . 225 ▫ System Activation . . . . . . . . . . . . . . . . . . . . . 225 ▫ Electronic Serial Number/Sirius Identification Number (ENS/SID) . . . . . . . . . . . . . . . . . . . . 226 ▫ Selecting Satellite Mode . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Automatic Temperature Control (ATC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 237 ▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . . 243 m Rear Window Features . . . . . . . . . . . . . . . . . . . 246 ▫ Electric Rear Window Defroster — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 173 INSTRUMENT PANEL FEATURES 4 1 2 3 4 5 — Air Outlet — Side Window Demister Outlet — Instrument Cluster — Ignition Switch — Analog Clock 6 — Radio 7 — Passenger Airbag 8 — Glove Box 9 — Heated Seat Switch* 10 — Electronic Stability Program Off Button* 11 — Hazard Switch 12 — Storage Compartment 13 — Climate Control 14 — Trunk Release Switch 15 — Power Top Switch * If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL BASE INSTRUMENT CLUSTER
UNDERSTANDING YOUR INSTRUMENT PANEL 175 PREMIUM INSTRUMENT CLUSTER 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Fuel Door Reminder This is a reminder that the Fuel Filler Door is located on the left side of the vehicle. 3. Temperature Gauge The temperature gauge shows engine coolant temperature. Any reading below the red area of the gauge shows that the engine cooling system is operating properly.
UNDERSTANDING YOUR INSTRUMENT PANEL 177 5. Low Fuel Light When the fuel level drops to 2 gallons, the fuel symbol will light and a single chime will sound. come on during starting, stays on, or comes on while driving, have the system checked by an authorized dealer. 6. Charging System Light This light shows the status of the electrical charging system. The light should come on briefly when the ignition is first turned on and remain on briefly as a bulb check.
UNDERSTANDING YOUR INSTRUMENT PANEL will turn off after the engine is started. If the bulb does not come on during starting, have the system checked by an authorized dealer. If the light comes on and remains on while driving, stop the vehicle and shut off the engine. DO NOT OPERATE THE VEHICLE UNTIL THE CAUSE IS CORRECTED. The light does not show the quantity of oil in the engine. This can be determined using the procedure shown in Section 7. 11.
UNDERSTANDING YOUR INSTRUMENT PANEL The two trip odometers show individual trip mileage. To switch from odometer to trip odometers, press and release the Trip Odometer button. To reset a trip odometer, display the desired trip odometer to be reset then push and hold the button until the display resets (approximately 2 seconds). Refer to “Trip Odometer Button” for additional information.
UNDERSTANDING YOUR INSTRUMENT PANEL indicator system is duty cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. NOTE: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary repeat this procedure. Unless reset, this message will continue to display each time you turn the ignition switch to the “ON” position.
UNDERSTANDING YOUR INSTRUMENT PANEL Dual Trip Odometer — If Equipped Press and release this button to change the display from odometer to “Trip A.” Press and release it a second time to change the display to “Trip B.” Press and release it a third time to change the display back to the odometer. To reset the trip odometer, first display the trip mileage that you want to reset, “Trip A” or “Trip B.” Then push and hold the button (approximately 2 seconds) until the display resets to 0.
UNDERSTANDING YOUR INSTRUMENT PANEL 19. Brake System Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system (if equipped). The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system.
UNDERSTANDING YOUR INSTRUMENT PANEL The operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON position. The light should illuminate for approximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the ON position.
UNDERSTANDING YOUR INSTRUMENT PANEL the conventional brake system will continue to operate normally provided that the BRAKE warning light is not on. If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefit of Anti-Lock Brakes. The ABS warning light should be checked frequently to assure that it is operating properly. Turn the ignition key to the on position, but do not start the vehicle. The light should come on.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if underinflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale.
UNDERSTANDING YOUR INSTRUMENT PANEL (Refer to “Tire Inflation Pressures” under “Tires — General Information” and to “Tire Pressure Monitor System (TPMS)” in Section 5 of this manual for more information). 25. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD that monitors emissions, engine, and automatic transaxle control systems. The light will illuminate when the key is in the ON/RUN position before engine start.
UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) – IF EQUIPPED 187 • System Status • Vehicle information warning message displays • Personal Settings (customer programmable features) • Compass heading display (N, S, E, W, NE, NW, SE, SW) • Outside temperature display (°F or °C) • Trip computer functions • Audio mode displays – 12 preset Radio Stations or CD Title and Track number when playing EVIC Display Location The Electronic Vehicle Information Center (EVIC) features
UNDERSTANDING YOUR INSTRUMENT PANEL The system allows the driver to select information by pressing the following buttons on the Instrument Panel Switch Bank: Press and release the MENU button to advance the display to Trip Functions or Personal Settings or to return to the default System Status MENU display. Button Press and release the STEP button to advance the display through the various Trip Functions or Personal Settings.
UNDERSTANDING YOUR INSTRUMENT PANEL • RKE (Remote Keyless Entry) Battery Low (with a single chime) • Personal Settings Not Available – Vehicle Not in Park.
UNDERSTANDING YOUR INSTRUMENT PANEL 1. Turn the ignition switch to the ON position (Do not start the engine). Press and release the STEP button to advance the display through the Trip Functions. 2. Fully depress the accelerator pedal slowly three times within 10 seconds. The Trip Functions mode displays the following information: 3. Turn the ignition switch to the LOCK position. • Average Fuel Economy Shows the average fuel economy since the last reset.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Significant changes in driving style or vehicle loading will greatly affect the actual drivable distance of the vehicle, regardless of the DTE display value. • When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change to a text display of LOW FUEL. This display will continue until the vehicle runs out of fuel.
UNDERSTANDING YOUR INSTRUMENT PANEL EVIC will flash the CAL indicator until the compass is calibrated. You may calibrate the compass by completing one or more 360° turns (in an area free from large metal or metallic objects) until the CAL indicator in the EVIC turns off. The compass will now function normally. Manual Compass Calibration If the compass appears erratic, inaccurate, or abnormal, you may wish to calibrate the compass manually.
UNDERSTANDING YOUR INSTRUMENT PANEL 193 1. Turn the ignition switch to the ON position. Leave the selector lever in PARK. 2. Press and release the MENU button until “Personal Settings” displays in the EVIC. 3. Press and release the STEP button until “Compass Variance” and the current Variance Value displays in the EVIC. 4. Press and release the RESET button to increment the Variance Value by one, (one button press per update), until the proper variance zone is selected according to the map.
UNDERSTANDING YOUR INSTRUMENT PANEL Personal Settings (Customer Programmable Features) Personal Settings allows the driver to set and recall features when the automatic transaxle is in PARK. Press and release the MENU button until “Personal Settings” displays in the EVIC. Press and release the STEP button to display the following programmable features: Language When in this display you may select different languages for all display nomenclature, including the trip functions.
UNDERSTANDING YOUR INSTRUMENT PANEL Sound Horn with LOCK When ON is selected, a short horn sound will occur when the remote keyless entry LOCK button is pressed. This feature may be selected with or without the flash lights on LOCK/UNLOCK feature. To make your selection, press and release the RESET button until ON or OFF appears. Flash Lights with LOCK When ON is selected, the front and rear turn signals will flash when the doors are locked or unlocked with the remote keyless entry transmitter.
UNDERSTANDING YOUR INSTRUMENT PANEL Key Off Power Delay When this feature is selected, the power window switches, radio, hands–free system (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned to the LOCK position. Opening a vehicle door will cancel this feature. To make your selection, press and hold the RESET button until OFF, 45 sec, 5 min, or 10 min appears.
UNDERSTANDING YOUR INSTRUMENT PANEL RADIO GENERAL INFORMATION Radio Broadcast Signals Your new radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile operation and natural phenomena, which might lead you to believe your sound system is malfunctioning.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the radio and steering wheel radio controls (if equipped) will remain active for 45 seconds after the ignition switch is turned to the LOCK position. Opening either door will cancel this feature. SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
UNDERSTANDING YOUR INSTRUMENT PANEL Phone Button (UConnectt Hands-Free Phone) — If Equipped Press this button to operate the Hands-Free Phone (UConnectt) feature (if equipped). Refer to “Hands-Free Communication (UConnectt)” in Section 3 for more information. If your vehicle is not equipped with or this feature is not available on your vehicle, a “UConnectt System Not Available” message will display on the radio screen. TIME Button Press the TIME button and the time of day will display.
UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM, FM or Satellite (if equipped) frequencies. 201 Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the Treble tones.
UNDERSTANDING YOUR INSTRUMENT PANEL seconds will allow the program format type to be selected. Many radio stations do not currently broadcast Music Type information.
UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode. If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be exited and the radio will tune to the preset station.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: These selections can only be made while playing a DVD. • VES Power - Allows you to turn VES™ ON and OFF (if equipped). • VES Lock - Locks out rear VES™ remote controls (if equipped). • VES CH1/CH2 - Allows the user to change mode of either the IR1 or IR2, wireless headphones, by pressing the AUDIO/SELECT button (if equipped). • Set Home Clock - Pressing the SELECT button will allow user to set the clock.
UNDERSTANDING YOUR INSTRUMENT PANEL 205 Subtitle Language — If Equipped Aspect Ratio — If Equipped Selecting this item allows you to choose a default subtitle language (effective only if the language is supported by the disc). You can select a language not listed by scrolling down and selecting 9other.9 Enter the country code using the TUNE/SCROLL control knob to scroll up and down to select the # and then push to select.
UNDERSTANDING YOUR INSTRUMENT PANEL SET Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the SET button, the station will continue to play but will not be stored into pushbutton memory.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The radio may shut down during extremely hot conditions. When this occurs, the radio will indicate “Disc Hot” and shut off until a safe temperature is reached. This shutdown is necessary to protect the optics of the DVD player and other radio internal components. NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the eject button for five seconds and all CDs will be ejected from the radio. The disc can be ejected with the radio and ignition OFF. SEEK Button (CD MODE) Press the right SEEK button for the next selection on the CD. Press the left SEEK button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file normally. UDF and Apple HFS formats are not supported. Multisession disc formats are supported by the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported. The majority of MP3/WMA files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates. MPEG Specification Sampling Frequency (kHz) Bit Rate (kbps) ID3 Tag information for artist, song title, and album title are supported for ID3 version 1 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported.
UNDERSTANDING YOUR INSTRUMENT PANEL • Number of files and folders - Loading times will increase with more files and folders To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. To create a single-session disc, enable the “Disc at Once” option before writing to the disc. LIST Button (DISC Mode for MP3/WMA Play) Pressing the LIST button will bring up a list of all folders on the disc.
UNDERSTANDING YOUR INSTRUMENT PANEL Pushing the AUX button will change the mode to auxiliary device if the AUX jack is connected. RW/FF (Auxiliary Mode) No function. NOTE: The AUX device must be turned on and the device’s volume set to proper level. If the AUX audio is not loud enough, turn the device’s volume up. If the AUX audio sounds distorted, turn the device’s volume down. SET Button (Auxiliary Mode) No function. SEEK Button (Auxiliary Mode) No function.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 Operating Instructions - Satellite Radio Mode (If Equipped) Refer to “Satellite Radio” in this section. intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited Operating Instructions - Video Entertainment System (VES™) (If Equipped) Refer to separate “Video Entertainment System (VES™) Guide.” DTS™ 9DTS9 and 9DTS 2.09 are trademarks of Digital Theater Systems, Inc.
UNDERSTANDING YOUR INSTRUMENT PANEL A 20 gigabyte Hard Drive (HDD) allows uploads of music and photos from CDs or through the USB port. While the Gracenote database finds the artist, track, and title for the music. An auxiliary input jack permits passengers to listen to a portable MP3 player through the vehicle’s speakers.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 Operating Instructions — Hands-Free Communication (UConnect™) (If Equipped) Refer to “Hands-Free Communication (UConnect™)” in Section 3 of this manual for detailed operating instructions. 4. To move the minute forward, touch the screen where the word “Min” with the arrow pointing upward is displayed. To move the minute backward, touch the screen where the word “Min” with the arrow pointing downward is displayed. Clock Setting Procedure 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 3. When this feature is on, a check mark will appear in the box next to the words “Daylight Savings.” Touch the screen where the words “Daylight Savings” are displayed to change the current setting. Show Time if Radio is Off When selected, this feature will display the time of day on the touch screen when the system is turned off. Proceed as follows to change the current setting: 1. Turn on the system. 2. Touch the screen where the time is displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RER — MULTIMEDIA SYSTEM — IF EQUIPPED NOTE: The sales code is located on the lower right side of the unit’s faceplate. The RER multimedia system contains a radio, Sirius Satellite Radio player, Navigation system, CD/DVD player, USB port, 20 gigabyte Hard Drive (HDD), and the UConnectt hands-free Bluetooth cellular system.
UNDERSTANDING YOUR INSTRUMENT PANEL rear seat passengers can watch a DVD on the optional rear-seat entertainment system while the driver and front seat passenger listen to the radio. Other special features include direct tune, music type selections, Traffic Messaging (optional), easy store presets, parental lockout for VES (if equipped), backup camera display for vehicles equipped with a backup camera, and on some models a dual display screen operation.
UNDERSTANDING YOUR INSTRUMENT PANEL Changing the Time Zone 1. Turn on the system. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. If the words “Time: GPS Time” are displayed at the top of the screen, proceed to Step 4. Otherwise, proceed to Step 3. 3. If the words “Time: User Clock” are displayed at the top of the screen, touch the bottom of the screen where the words “User Clock” are displayed. The GPS time setting menu will appear on the screen. 4.
UNDERSTANDING YOUR INSTRUMENT PANEL 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. If the words “Time: User Clock” are displayed at the top of the screen, proceed to Step 4. Otherwise, proceed to Step 3. 3. If the words “Time: GPS Time” are displayed at the top of the screen, touch the bottom of the screen where the words “GPS Time” are displayed. The user clock time setting menu will appear on the screen. 4.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 UNIVERSAL CONSUMER INTERFACE (UCI) — IF EQUIPPED • the iPodt battery charges when plugged into the UCI connector. NOTE: This section is for sales code and REQ radios only with UConnect.™ For sales code REN touch screen radio, refer to the separate User’s Manual. Connecting the iPodT Device Use the optional connection cable to connect an iPodt to the vehicle’s UCI connector (which is located in the glove box on some vehicles. This location may vary with vehicle).
UNDERSTANDING YOUR INSTRUMENT PANEL Play Mode When switched to UCI mode the iPodt will be in Play mode. In this Play mode , you may use the following buttons on the radio faceplate to control the iPodt and display data: TUNE/SCROLL Knob Use the “TUNE/SCROLL” knob to go to the next or previous track. The “TUNE/SCROLL” knob functions similar to the scroll wheel on the iPodt mobile digital device. Turning it clockwise (forward) by one click while playing a track skips to the next track.
UNDERSTANDING YOUR INSTRUMENT PANEL previous track in the list, if you press this button at any other time in the current track it will go back to the beginning of the track. If the right (up) button is pressed during Play mode, it will go to the next track in the list. INFO Button Press the “INFO” button while a track is playing to see the information (Track Title, Artist, Album, etc.) for that track. Each press the “INFO” button will take you to the next screen of data for that track.
UNDERSTANDING YOUR INSTRUMENT PANEL display, press the “TUNE/SCROLL” knob to select and start playing the track. By turning the “TUNE/SCROLL” knob fast, you can jump through the list faster. During fast scroll, you may notice a slight delay in updating the information on the radio display. During all List modes, the iPodt will display all lists in “wrap-around” mode.
UNDERSTANDING YOUR INSTRUMENT PANEL can follow the same steps to go to the desired track in that list. Not all iPodt sub menu levels are available on this system. MUSIC TYPE Button The “MUSIC TYPE” button is another shortcut button to the genre listing on your iPodt. SATELLITE RADIO (RSC) — IF EQUIPPED (RER/REQ/REN RADIOS ONLY) Satellite radio uses direct satellite to receiver broadcasting technology to provide clear digital sound, coast to coast.
UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Serial Number/Sirius Identification Number (ENS/SID) The Electronic Serial Number/Sirius Identification Number is needed to activate your Sirius Satellite Radio system. To access the ESN/SID, refer to the following steps: ESN/SID Access With the ignition switch in the ON/RUN or ACCESSORY position and the radio ON, press the SETUP button and scroll using the TUNE control knob until Sirius ID is selected.
UNDERSTANDING YOUR INSTRUMENT PANEL Reception Quality Satellite reception may be interrupted due to one of the following reasons: • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception in the form of short audio mutes. • Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage.
UNDERSTANDING YOUR INSTRUMENT PANEL 3 seconds will make the radio display the Song Title all of the time (press and hold again to return to normal display). By pressing the SEEK button when the Music Type function is active, the radio will be tuned to the next channel with the same selected Music Type name. RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next channel in the direction of the arrows.
UNDERSTANDING YOUR INSTRUMENT PANEL Select the button (1-6) you wish to lock onto this channel and press and release that button. If a button is not selected within 5 seconds after pressing the SET button, the channel will continue to play but will not be stored into push-button memory. You may add a second channel to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2.
UNDERSTANDING YOUR INSTRUMENT PANEL REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. The left- and right-hand controls are rocker-type switches with a push-button in the center of each switch. Reach behind the steering wheel to access the switches. Right-Hand Switch Functions • Press the top of the switch to increase the volume. • Press the bottom of the switch to decrease the volume.
UNDERSTANDING YOUR INSTRUMENT PANEL Left-Hand Switch Functions for Media (i.e. CD) Operation 231 • Press the bottom of the switch once either to listen to the beginning of the current track or to listen to the beginning of the previous track if it is within one second after the current track begins to play. RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being ON in your vehicle can cause erratic or noisy performance from your radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 3. Do not apply paper, paper CD labels, or tape to the disc; avoid scratching the disc. Manual Air Conditioning and Heating System 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. 8. Do not play discs that are small in size or have irregular shapes.
UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control 233 Temperature Control Rotate this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control to the right from the “O” (Off) position. There are four blower speeds. Rotate this control to regulate the temperature of the air inside the passenger compartment.
UNDERSTANDING YOUR INSTRUMENT PANEL Mode Control (Air Direction) Rotate this control to choose from several patterns of air distribution. You can select either a primary mode as identified by the symbols on the control, or a blend of two of these modes. The closer the setting is to a particular symbol, the more air distribution you receive from that mode. Panel Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow.
UNDERSTANDING YOUR INSTRUMENT PANEL 235 Mix Recirculation Control Air is directed through the floor, defrost, and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. Press in on this button to block the flow of outside air from coming into the passenger compartment. A light will illuminate when the system is in recirculation mode.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • Continuous use of the recirculation mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. • The use of the recirculation mode in cold or damp weather will cause windows to fog on the inside, because of moisture build-up inside the vehicle. Select the Outside Air position for maximum defogging.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 • ECONOMY MODE If economy mode is desired, press the A/C button to turn off the indicator light and the A/C compressor. Then, move the temperature control to the desired temperature. comfort levels desired by the driver and passenger. To accomplish this, the system gathers information from the cabin infrared sensor mounted between the sun-visors and from various sensors located throughout the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 2. Dial in the temperature you would like the system to maintain by rotating the Temperature Control knob. Once the comfort level is selected, the system will maintain that level automatically using the heating system. Should the desired comfort level require air conditioning, the system will automatically make the adjustment. You will experience the greatest efficiency by simply allowing the system to function automatically.
UNDERSTANDING YOUR INSTRUMENT PANEL Manual Operation This system offers a full complement of manual override features, which consist of Blower Preferred Automatic, Mode Preferred Automatic, or Blower and Mode Preferred Automatic. This means the operator can override the blower, the mode, or both. There is a manual blower range for times when the AUTO setting is not desired. 239 The blower can be set to any fixed blower speed by rotating the Blower Control knob (on the left).
UNDERSTANDING YOUR INSTRUMENT PANEL
UNDERSTANDING YOUR INSTRUMENT PANEL The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Control knob (on the right) to one of the following positions. • Panel Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. NOTE: The center instrument panel outlets can be aimed so that they are directed toward the rear seat passengers for maximum airflow to the rear.
UNDERSTANDING YOUR INSTRUMENT PANEL • Air Conditioner Control Press this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the Mode control dial. Press this button a second time to turn off the air conditioning. An LED in the button illuminates when manual compressor operation is selected. • Recirculation Control The system will automatically control recirculation.
UNDERSTANDING YOUR INSTRUMENT PANEL • Most of the time, when in Automatic Operation, you can temporarily put the system into Recirculation Mode by pressing the Recirculation Button. However, under certain conditions, while in Automatic Mode, the system is blowing air out the defrost vents. When these conditions are present, and the Recirculation Button is pressed, the indicator will flash and then turn off. This tells you that you are unable to go into recirculation mode at this time.
UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Interior fogging on the windshield can be quickly removed by turning the mode selector to Defrost. The Defrost/Floor mode can be used to maintain a clear windshield and provide sufficient heating. If side window fogging becomes a problem, increase blower speed. Vehicle windows tend to fog on the inside in mild but rainy or humid weather. NOTE: Recirculate without A/C should not be used for long periods as fogging may occur.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 Control Setting Suggestions for Various Weather Conditions 4
UNDERSTANDING YOUR INSTRUMENT PANEL REAR WINDOW FEATURES Electric Rear Window Defroster — If Equipped The electric Rear Window Defroster Control is located on the climate control. Press this button to turn on the rear window defroster and the heated side mirrors (if equipped). An LED in the button will illuminate when the rear window defroster is ON.
STARTING AND OPERATING CONTENTS m Starting Procedures . . . . . . . . . . . . . . . . . . . . . 251 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . . 251 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 252 ▫ Automatic Transaxle Ignition Interlock System . . . . . . . . . . . . . . . . . . . . . . 257 ▫ 4 Speed Or 6 Speed (AutoStickt) Automatic Transaxle . . . . . . . . . . . . . . . . . . . 258 ▫ Extremely Cold Weather (Below 220°F Or 229°C) . . . . . . . . . . . . . . . .
STARTING AND OPERATING m Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 270 ▫ Synchronizing ESP . . . . . . . . . . . . . . . . . . . . 279 m Driving On Slippery Surfaces . . . . . . . . . . . . . . 271 m Tire Safety Information . . . . . . . . . . . . . . . . . . . 280 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . . 271 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 280 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 249 ▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . . 295 ▫ 3.5L Engine . . . . . . . . . . . . . . . . . . . . . . . . . 308 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . . 296 ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . . 309 ▫ Alignment And Balance . . . . . . . . . . . . . . . . . 297 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . . 309 m Tire Chains . . . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING ▫ Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315 ▫ Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 ▫ Cruising Range . . . . . . . . . . . . . . . . . . . . . . . 315 m Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . 322 ▫ Replacement Parts . . . . . . . . . . . . . . . . . . . . . 315 ▫ Common Towing Definitions . . . . . . . . . . . . . 322 ▫ Maintenance . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! • Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition.
STARTING AND OPERATING Normal Starting NOTE: Normal starting of either a cold or a warm engine is obtained without pumping or depressing the accelerator pedal. For vehicles not equipped with Tip Start, turn the ignition switch to the START position and release it when the engine starts. If the engine fails to start within 10 seconds, turn the ignition switch to the LOCK position, wait 10 to 15 seconds, then repeat the normal starting procedure.
STARTING AND OPERATING If Engine Fails to Start WARNING! • Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way.
STARTING AND OPERATING seconds with the accelerator pedal pushed all the way to the floor. Release the accelerator pedal and the key once the engine is running smoothly. If the engine shows no sign of starting after two 15second periods of cranking with the accelerator pedal held to the floor, repeat the “Normal Starting” or “Extreme Cold Weather” procedures.
STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt AC electrical outlet with a grounded, three-wire extension cord. The engine block heater cord is bundled under the hood between the headlight assembly and the Totally Integrated Power Module (Fuse Box) on the driver side of the vehicle. WARNING! Remember to disconnect the cord before driving.
STARTING AND OPERATING WARNING! • It is dangerous to shift the selector lever out of or if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal. • Unintended movement of a vehicle could injure those in and near the vehicle.
STARTING AND OPERATING • Insert a key, screwdriver, or finger into the hole at the front of the cup holder and push and hold the manual override release lever forward. • While holding the release lever forward, move the gear selector lever from PARK to NEUTRAL. • Release the manual override. NOTE: If this occurs, even if the override is successful, it is recommended that you visit a dealer at your earliest possible convenience. Your dealer has diagnostic equipment to determine if the problem could recur.
STARTING AND OPERATING 4 Speed or 6 Speed (AutoStickT) Automatic Transaxle The electronically controlled transaxle provides a precise shift schedule. The transaxle electronics are selfcalibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles. Gear Ranges “P” PARK “P” PARK supplements the parking brake by locking the transaxle. The engine can be started in this range.
STARTING AND OPERATING WARNING! Never use PARK position on an Automatic Transaxle as a substitute for the parking brake. Always apply parking brake fully when parked to guard against vehicle movement and possible injury or damage. 259 REVERSE Use this range for moving the vehicle rearward. Shift into this range only after the vehicle has come to a complete stop. NEUTRAL Engine may be started in this range.
STARTING AND OPERATING DRIVE (OVERDRIVE) With 6–Speed Transaxle This range should be used for most city and highway driving. It provides the smoothest upshifts, downshifts, and best fuel economy. However, use the AutoStickt mode and select the [5] range when frequent transaxle shifting occurs while using the DRIVE range, such as when operating the vehicle under heavy loading conditions, (i.e. in hilly terrain, traveling into strong head winds or while towing heavy trailers).
STARTING AND OPERATING occur only to prevent engine overspeed while downshifts occur earlier than other gear range selections. CAUTION! If the transaxle operating temperature exceeds acceptable limits, the vehicle computer will override DRIVE (OVERDRIVE) and [5] for 6–Speed AutoStickt transaxle and [3] for 4–Speed auto transaxle, range by changing shift points. This is done to prevent transaxle damage due to overheating. 261 PARK, REVERSE, and NEUTRAL will continue to operate.
STARTING AND OPERATING NOTE: Even if the transaxle can be reset, it is recommended that you visit a dealer at your earliest possible convenience. Your dealer has diagnostic equipment to determine if the problem could recur. If the transaxle cannot be reset, dealer service is required. AUTOSTICKT — IF EQUIPPED AutoStickt is a driver-interactive transaxle that offers six manual ratio changes to provide you with more control of the vehicle.
STARTING AND OPERATING 263 AutoStickT Operation By placing the selector lever one shift-level below the 9D9 (Drive) position, it can be moved from side to side. This allows the driver to select a higher or lower range of gears. Moving the selector lever to the Left (-) triggers a downshift and to the Right (+) an upshift. The gear position will display in the instrument cluster on the transaxle range indicator.
STARTING AND OPERATING • Transaxle shifting will be more noticeable when Autostickt is engaged. • If a low range is selected and the engine accelerates to the rev limit, the transaxle will automatically select the next higher ratio. • If a downshift would cause the engine to over-speed, that shift will not occur until it is safe for the engine.
STARTING AND OPERATING 265 When parking on a hill, it is important to apply the parking brake before placing the gear selector lever in “P” (Park), otherwise the load on the transaxle locking mechanism may make it difficult to move the selector out of park. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. To apply the parking brake, grasp the handle and pull it upward until you feel resistance.
STARTING AND OPERATING • If the parking brake is applied while the vehicle is moving, a chime will sound to alert the driver. The chime will sound up to 10 times or until the vehicle has returned to a stop. The Brake System Warning Light in the instrument cluster will turn on when the parking brake is applied and the ignition switch is on. NOTE: This light only shows that the parking brake is applied. It does not show the degree of brake application.
STARTING AND OPERATING BRAKE SYSTEM Your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems loses normal capability, the remaining system will still function. However, there will be some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop the vehicle.
STARTING AND OPERATING Anti-Lock Brake System — If Equipped The Anti-Lock Brake System provides increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up. You also may experience the following when the brake system goes into Anti-lock: When the vehicle is driven over 7 mph (11 km/h), you may also hear a slight clicking sound as well as some related motor noises.
STARTING AND OPERATING WARNING! • The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals. • Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident.
STARTING AND OPERATING If both the Brake System Warning Light and the ABS Light remain on, the Anti-Lock brakes (ABS) and Electronic Brake Force Distribution (EBD) systems are not functioning. Immediate repair to the ABS system is required. POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost.
STARTING AND OPERATING 271 CAUTION! WARNING! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur. Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have an accident.
STARTING AND OPERATING 2. Slow down if road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain enough distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop. DRIVING THROUGH WATER Driving through water more than a few inches/ millimeters deep will require extra caution to ensure safety and prevent damage to your vehicle.
STARTING AND OPERATING 273 CAUTION! WARNING! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • Driving through standing water limits your vehicle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water.
STARTING AND OPERATING TRACTION CONTROL SYSTEM (TCS) — IF EQUIPPED This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the TCS system functions similar to a limited slip differential and controls the wheel spin across a driven axle.
STARTING AND OPERATING BRAKE ASSIST SYSTEM (BAS) — IF EQUIPPED This system complements the Anti-Lock Brake System (ABS) by optimizing the vehicle braking capability during emergency braking maneuvers. This system detects an emergency braking situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce braking distances. Applying the brakes very quickly results in the best BAS assistance.
STARTING AND OPERATING ELECTRONIC STABILITY PROGRAM (ESP) — IF EQUIPPED This system enhances directional control and stability of the vehicle under various driving conditions. The ESP corrects for oversteering and understeering the vehicle by applying the brake of the appropriate wheel. Engine power may also be reduced to assist in counteracting the condition of oversteer or understeer and help the vehicle maintain the desired path.
STARTING AND OPERATING WARNING! • The ESP cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. • The ESP cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING When in “Partial Off” mode, the engine torque reduction feature is cancelled. Therefore, the enhanced vehicle stability offered by ESP is unavailable. However, a feature of the system remains active. This feature controls wheel spin across an axle quite similarly to a limited slip differential.
STARTING AND OPERATING The system will turn the “ESP/BAS Malfunction Indicator Light” on continuously while the engine running if it detects a malfunction in either the ESP or the BAS or both. If the light remains on after several ignition cycles, and you have driven the vehicle several miles at speeds greater than 30 mph (48 km/h), and the ESP is synchronized (refer to Synchronizing ESP), see your authorized dealer as soon as possible to have the problem diagnosed and corrected.
STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter 9P9 is absent from this tire size designation. Example: 215/65R15 96H • LT (Light Truck)-Metric tire sizing is based on U.S. design standards.
STARTING AND OPERATING 281 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards (....blank....( = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire 10.
STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions (i.e.
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including date code, 283 located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar.
STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard and in the “Vehicle Loading” section of this manual.
STARTING AND OPERATING 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “XXX” amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs (295 kg) 5. Determine the combined weight of luggage and cargo being loaded on the vehicle.
STARTING AND OPERATING 287 5
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation, also increases tire rolling resistance and results in higher fuel consumption. 289 maximum loaded vehicle condition. These pressure conditions will be found in the “Supplemental Tire Pressure Information” section of this manual. 3.
STARTING AND OPERATING check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.
STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high-speed vehicle operation.
STARTING AND OPERATING Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and reinstalled at the first opportunity. WARNING! Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). Temporary-use spare tires have limited tread life.
STARTING AND OPERATING 293 CAUTION! WARNING! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result. The limited use spare tires are for emergency use only. Installation of this limited use spare tire affects vehicle handling. With this tire, do not drive more than 50 mph (80 km/h).
STARTING AND OPERATING WARNING! WARNING! Prolonged use of limited use spare, or incorrect tire size of front wheel, may damage the transaxle differential and result in loss of vehicle mobility and could result in loss of vehicle control. Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone.
STARTING AND OPERATING 295 Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Many states have laws requiring tire replacement at this point.
STARTING AND OPERATING Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
STARTING AND OPERATING CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. Alignment And Balance Poor suspension alignment may result in: • Fast tire wear. • Uneven tire wear, such as feathering and one-sided wear. • Vehicle pull to right or left. Tires may also cause the vehicle to pull to the left or right. Alignment will not correct this condition. See your dealer for proper diagnosis.
STARTING AND OPERATING SNOW TIRES Some areas of the country require the use of snow tires during winter. Standard tires are of the all season type and satisfy this requirement as indicated by the M+S designation on the tire sidewall. If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of 4, failure to do so may adversely affect the safety and handling of your vehicle.
STARTING AND OPERATING The suggested rotation method is the “forward-cross” shown in the following diagram. TIRE PRESSURE MONITOR SYSTEM (TPMS) — IF EQUIPPED • The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. • The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12°F (7°C). This means that 299 when the outside temperature decreases, the tire pressure will decrease.
STARTING AND OPERATING • The TPM System will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold placard pressure. Once the low tire pressure warning (Tire Pressure Monitoring Telltale Light) illuminates, you must increase the tire pressure to the recommended cold placard pressure in order for the Tire Pressure Monitoring Telltale Light to turn off.
STARTING AND OPERATING CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, and the TPMS will monitor the actual tire pressure in the tire. Base System — If Equipped The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the Receiver Module.
STARTING AND OPERATING 303 repeat, providing the system fault still exists. The Tire Pressure Monitoring Telltale Light will turn off when the fault condition no longer exists. A system fault can occur due to any of the following: 2. If you install the compact spare tire in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition key cycle, a chime will sound and the TPM Telltale Light will turn ON. 1.
STARTING AND OPERATING Premium System — If Equipped The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the Receiver Module. NOTE: It is particularly important for you to check the tire pressure in all of the tires on your vehicle monthly and to maintain the proper pressure.
STARTING AND OPERATING 305 Should this occur, you should stop as soon as possible, and inflate the tires with low pressure (those flashing in the EVIC graphic) to the vehicle’s recommended cold placard pressure value. Once the system receives the updated tire pressures, the system will automatically update, the graphic display in the EVIC will stop flashing, and the Tire Pressure Monitoring Telltale Light will turn off.
STARTING AND OPERATING 1. Jamming due to electronic devices or driving next to facilities emitting the same Radio Frequencies as the TPM sensors. Light will remain ON, a chime will sound, and the EVIC will still display a flashing pressure value in the graphic display. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3.
STARTING AND OPERATING TPM Telltale Light will turn OFF and the graphic in the EVIC will display a new pressure value instead of dashes (- -), as long no tire pressure is below the low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada.
STARTING AND OPERATING 3.5L Engine The 3.5L engine is designed to meet all emissions regulations and provide satisfactory fuel economy and performance when using high-quality unleaded gasoline having an octane range of 87 to 89. The manufacturer recommends the use of 89 octane for optimum performance. The use of premium gasoline is not recommended.
STARTING AND OPERATING Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasolines contain oxygenates, and are specifically blended to reduce vehicle emissions and improve air quality. The manufacturer supports the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability of engine and fuel system components.
STARTING AND OPERATING MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT. Gasoline blended with MMT reduces spark plug life and reduces emission system performance in some vehicles. The manufacturer recommends that gasoline without MMT be used in your vehicle.
STARTING AND OPERATING • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your dealer for service assistance. • The use of fuel additives, which are now being sold as octane enhancers is not recommended. Most of these products contain high concentrations of methanol.
STARTING AND OPERATING • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. vehicles. Please refer to the other sections of this manual for information on features that are common between Flexible Fuel and gasoline only powered vehicles.
STARTING AND OPERATING CAUTION! Only vehicles with the E-85 fuel filler door label can operate on E-85. 313 ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame.
STARTING AND OPERATING For best results, a refueling pattern that alternates between E-85 and unleaded gasoline should be avoided.
STARTING AND OPERATING Starting The characteristics of E-85 fuel make it unsuitable for use when ambient temperatures fall below 0° F (-18° C). In the range of 0° F (-18° C) to 32° F (0° C), you may experience an increase in the time it takes for your engine to start, and a deterioration in drivability (sags and/or hesitations) until the engine is fully warmed up. Cruising Range Because E-85 fuel contains less energy per gallon than gasoline, you will experience an increase in fuel consumption.
STARTING AND OPERATING ADDING FUEL Fuel Filler Cap (Gas Cap) As a reminder, a fuel icon with an arrow indicating which side of the vehicle the fuel filler door is located on, is located in the instrument cluster, just below the Fuel Gage. The gas cap is located behind the fuel filler door on the left rear of the vehicle. Push in on the right side of the fuel filler door (near the edge) and release and the door will open. Then, grasp the door and open it.
STARTING AND OPERATING After removing the gas cap, lay the cap tether in the hook on the inside of the fuel door. This keeps the gas cap suspended away from the vehicle’s surface. 317 CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap could let impurities into the fuel system. • A poorly fitting gas cap may cause the Malfunction Indicator Light to turn on.
STARTING AND OPERATING WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel when the engine is running. This is in violation of most state and federal fire regulations and doing so will cause the malfunction indicator light to turn on. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
STARTING AND OPERATING VEHICLE LOADING The load carrying capacity of your vehicle is shown on the “Vehicle Certification Label.” This information should be used for passenger and luggage loading as indicated. Vehicle Curb Weight 2.4 L Base. . . . . . . . 2.7 L Base. . . . . . . . 2.7 L Touring . . . . . 2.7 L Limited . . . . . 3.5 L Limited . . . . .
STARTING AND OPERATING Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR. WARNING! Because the front wheels steer the vehicle, it is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident.
STARTING AND OPERATING Loading To load your vehicle properly, first figure out its empty weight, axle by axle and side by side. Store heavier items down low and be sure you distribute their weight as evenly as possible. Stow all loose items securely before driving. If weighing the loaded vehicle shows that you have exceeded either GAWR, but the total load is within the specified GVWR, you must redistribute the weight.
STARTING AND OPERATING TRAILER TOWING In this section, you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible. To maintain warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.
STARTING AND OPERATING weighed in combination. (Note that GCWR ratings include a 150 lbs (68 kg) allowance for the presence of a driver). Gross Axle Weight Rating (GAWR) The Gross Axle Weight Rating (GAWR) is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR. WARNING! It is important that you do not exceed the maximum front or rear GAWR.
STARTING AND OPERATING Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the Trailer Towing Weights (Maximum Trailer Weight Ratings) chart for the Max. GTW towable for your given drivetrain. Trailer Hitch Classification Class Max. GTW (Gross Trailer Wt.
STARTING AND OPERATING 325 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transaxle Max. Frontal Area Max. 2.4L/Auto See Note 2 2.7L/Auto See Note 2 3.5L/Auto 22 Sq., Ft. (2.0 Sq. M) Refer to local laws for maximum trailer towing speeds.
STARTING AND OPERATING CAUTION! Towing a trailer with a larger than recommended frontal area could cause the engine to overheat or cause severe engine damage under extreme conditions. Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the “Tire and Loading Information” placard under “Tire Safety Information” in Section 5 of this manual for the maximum combined weight of occupants and cargo for your vehicle.
STARTING AND OPERATING WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and that it will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident.
STARTING AND OPERATING 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve 10% of tongue weight as a percentage of total trailer weight). Towing Requirements — Tires − Do not attempt to tow a trailer while using a compact spare tire. − Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING − Trailer brakes are recommended for trailers over 1,000 lbs (450 kg) and required for trailers in excess of 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (450 kg) loaded, it should have its own brakes, and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. WARNING! Do not connect trailer brakes to your vehicle’s hydraulic brake lines.
STARTING AND OPERATING 331 Use a factory approved trailer harness and connector. NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. 5 7- Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping, and backing the trailer in an area located away from heavy traffic.
STARTING AND OPERATING Towing Tips — Automatic Transaxle The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance and extend transaxle life by reducing excessive shifting and heat build up. This action will also provide better engine braking.
STARTING AND OPERATING 333 − Air Conditioning Turn off temporarily. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) − Refer to “Cooling System” under “Maintenance Procedures” in Section 7 of this manual for more information. TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the ground) Recreational towing for this vehicle is not recommended.
WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 336 m Jump-Starting Procedures . . . . . . . . . . . . . . . . . 344 m If Your Engine Overheats . . . . . . . . . . . . . . . . . 336 m Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . 348 ▫ Engine Oil Overheating — 2.4L Engine Only (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . . 337 m Towing A Disabled Vehicle . . . . . . . . . . . . . . . . 349 m Jacking And Tire Changing . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Flasher switch is located in the Instrument Panel Switch Bank above the climate controls. Push and release the switch to turn on the Hazard Warning Flashers. When the Hazard Warning is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Push and release the switch a second time to turn off the flashers.
WHAT TO DO IN EMERGENCIES the fan control to High. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the H (red) mark, the instrument cluster will sound a chime. Pull over and stop the vehicle with the engine at idle, when safe. Turn off the air conditioning and wait until the pointer drops back into the normal range.
WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack.
WHAT TO DO IN EMERGENCIES 6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if changing the right front tire, block the left rear wheel. 339 Spare Tire Removal Lift up the load floor cover and remove the hold down. Jack Location The jack and jack-handle are stowed under the load floor in the trunk. Spare Tire Stowage The compact spare tire is stowed under the rear load floor in the trunk.
WHAT TO DO IN EMERGENCIES Jacking Instructions 1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench, and remove the wrench from the jack assembly. NOTE: The Jack Handle attaches to the side of the jack with two attachment points. When the jack is partially expanded, the tension between the two attachment points holds the jack handle in place. Removing Jack Handle From Jack 2.
WHAT TO DO IN EMERGENCIES 341 6 Jacking Locations
WHAT TO DO IN EMERGENCIES CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in step 3. 3. There is one front jacking location and one rear jacking location on each side of the vehicle. The front locations are outlined by two triangular cutouts, the rear ones by two rectangular cutouts. For vehicles equipped with plastic trim, the plastic has been cut away to expose the jacking locations in the body.
WHAT TO DO IN EMERGENCIES and wheel nuts with the cone shaped end of the nuts toward the wheel. Lightly tighten the nuts. To avoid the risk of forcing the vehicle off the jack, do not tighten the nuts fully until the vehicle has been lowered. WARNING! 343 8. Finish tightening the nuts. Push down on the wrench while tightening the wheel nuts. Alternate nuts, until each nut has been tightened twice. Correct wheel nut torque is 100 ft. lbs (135 N. m).
WHAT TO DO IN EMERGENCIES 10. Place the deflated (flat) tire in the cargo area, have the tire repaired or replaced as soon as possible. WARNING! A loose tire thrown forward in a collision or hard stop could injure the occupants in the vehicle. Have the deflated (flat) tire repaired or replaced immediately. 11. Check the tire pressure as soon as possible. Correct pressure as required. JUMP-STARTING PROCEDURES WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised.
WHAT TO DO IN EMERGENCIES WARNING! • Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin, or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush contaminated area immediately with large quantities of water. • A battery generates hydrogen gas, which is flammable and explosive. Keep flame or spark away from the vent holes.
WHAT TO DO IN EMERGENCIES 3. Turn off the heater, radio, and all unnecessary electrical loads. 4. Remove the protective cover over the remote jumpstart positive battery post (+) in the engine compartment. Connect one end of the jumper cable to the positive battery post. Connect the other end of the same cable to the positive terminal of the booster battery. Refer to the following illustration for jump-starting connections. 5.
WHAT TO DO IN EMERGENCIES 347 7. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery. NOTE: Refer to “Maintenance Procedures” in Section 7 of this manual for information on accessing the battery for service or replacement. 8. When removing the jumper cables, reverse the sequence exactly. Be careful of the moving belts and fan. WARNING! 9.
WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand, or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth between Reverse and First gear. Usually the least accelerator pedal pressure to maintain the rocking motion without spinning the wheels is most effective.
WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE WITHOUT THE IGNITION KEY Special care must be taken when the vehicle is towed with the ignition in the LOCK position. Flat bed towing is the preferred towing method. However, if a flat bed towing vehicle is not available, a wheel lift towing vehicle may be used. Furthermore, rear towing is not recommended with the front wheels on the ground, as transaxle damage can result. If rear towing is the only alternative, a front end dolly must be used.
WHAT TO DO IN EMERGENCIES CAUTION! • If the vehicle being towed requires steering, the ignition switch must be in the ON position, not in the LOCK or ACC position. • Do not attempt to tow this vehicle from the front with sling type towing equipment. Damage to the front fascia will result. • Do not push or tow this vehicle with another vehicle as damage to the bumper fascia and transaxle may result. If you must use the accessories (wipers, defrosters, etc.
MAINTAINING YOUR VEHICLE CONTENTS m 2.4L Engine Compartment . . . . . . . . . . . . . . . . 354 m Maintenance Procedures . . . . . . . . . . . . . . . . . . 361 m 2.7L Engine Compartment . . . . . . . . . . . . . . . . 355 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 361 m 3.5L Engine Compartment . . . . . . . . . . . . . . . . 356 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . . 365 m Onboard Diagnostic System — OBD II . . . . . . . . 357 ▫ Drive Belt . . . . . . .
MAINTAINING YOUR VEHICLE ▫ A/C Air Filter — If Equipped . . . . . . . . . . . . 370 ▫ Front And Rear Wheel Bearings . . . . . . . . . . . 387 ▫ Power Steering — Fluid Check . . . . . . . . . . . . 371 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . 387 ▫ Front Suspension Ball Joints . . . . . . . . . . . . . . 372 ▫ Steering Linkage . . . . . . . . . . . . . . . . . . . . . . 372 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 353 ▫ Front Fog Light . . . . . . . . . . . . . . . . . . . . . . 403 m Fluids And Capacities . . . . . . . . . . . . . . . . . . . 409 ▫ Tail/Stop Light, Rear Turn Signal Light, Backup Light . . . . . . . . . . . . . . . . . . . . . . . . 404 m Fluids, Lubricants, And Genuine Parts . . . . . . . . 410 ▫ License Plate Light . . . . . . . . . . . . . . . . . . . . 407 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 2.
MAINTAINING YOUR VEHICLE 355 2.
MAINTAINING YOUR VEHICLE 3.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transaxle control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE Loose Fuel Filler Cap Message If the vehicle diagnostic system determines that the fuel filler cap in loose, improperly installed, or damaged, a “gASCAP” message will display in the instrument cluster. Tighten the gas cap until a “clicking” sound is heard. This is an indication that the gas cap is properly tightened. Press the trip odometer reset button to turn off the message. If the problem persists, the message will appear the next time the vehicle is started.
MAINTAINING YOUR VEHICLE Your vehicle has a simple ignition key-actuated test, which you can use prior to going to the test station. To check if your vehicle’s OBD system is ready, you must do the following: 1. Insert your ignition key into the ignition switch. 2. Turn the ignition to the ON position, but do not crank or start the engine. 3. If you crank or start the engine, you will have to start this test over. 4.
MAINTAINING YOUR VEHICLE vehicle serviced before going to the I/M station. The I/M station can fail your vehicle because the MIL symbol is on with the engine running. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. REPLACEMENT PARTS Use of genuine Mopart parts for normal/scheduled maintenance and repairs is highly recommended to ensure the designed performance.
MAINTAINING YOUR VEHICLE MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance. However, if a malfunction of these items does occur, it could adversely affect the engine or vehicle performance.
MAINTAINING YOUR VEHICLE CAUTION! Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Engine Oil Dipstick Change Engine Oil The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to “Maintenance Schedule” in Section 8 of this manual for information on this system.
MAINTAINING YOUR VEHICLE Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer recommends engine oils that are API Certified and meet the requirements of DaimlerChrysler Material Standard MS6395. American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils.
MAINTAINING YOUR VEHICLE Lubricants which do not have both, the engine oil certification mark and the correct SAE viscosity grade number should not be used. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to the “Engine Compartment” illustration in this section. Lubricants which do not have both, the engine oil certification mark and the correct SAE viscosity grade number should not be used.
MAINTAINING YOUR VEHICLE Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Engine Oil Filter Selection All of this manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high quality filters should be used to assure most efficient service. Mopart Engine Oil Filters are high quality oil filters and are recommended.
MAINTAINING YOUR VEHICLE WARNING! The air induction system (air cleaner, hoses, etc) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc) removed. Failure to do so can result in serious personal injury.
MAINTAINING YOUR VEHICLE NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn.
MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin, or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post.
MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. 369 WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system.
MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment. The A/C Air Filter is located in the fresh air inlet behind the glove box.
MAINTAINING YOUR VEHICLE 5. Disengage the two retaining tabs that secure the filter cover to the HVAC housing and remove the cover. 371 7. Install the A/C Air Filter with the arrow on the filter pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the cover. CAUTION! The A/C Air Filter is labeled with an arrow to indicate airflow direction through the filter. Failure to install the filter properly will result in the need to replace it more often. 8.
MAINTAINING YOUR VEHICLE apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through a certified DaimlerChrysler Dealership. WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level.
MAINTAINING YOUR VEHICLE 373 attention should also be given to hood latching components to insure proper function. When performing other underhood services, the hood latch, release mechanism, and safety catch should be cleaned and lubricated. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield.
MAINTAINING YOUR VEHICLE Windshield Washers NOTE: Refer to the appropriate “Engine Compartment” diagram in Section 7 for the location of the windshield washer fluid reservoir. The fluid reservoir for the windshield washers is located in the engine compartment. Be sure to check the fluid level in the reservoir at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water.
MAINTAINING YOUR VEHICLE WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to Exhaust Gas in the Safety Tips section of this manual. 375 Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the LOCK position.
MAINTAINING YOUR VEHICLE Coolant Checks Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed, and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser.
MAINTAINING YOUR VEHICLE CAUTION! • Mixing of coolants other than specified HOAT engine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible. • Do not use plain water alone or alcohol-base engine coolant (antifreeze) products.
MAINTAINING YOUR VEHICLE • Use only high purity water such as distilled or deionized water when mixing the water/engine coolant solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated.
MAINTAINING YOUR VEHICLE Disposal of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children, do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately.
MAINTAINING YOUR VEHICLE humidity accumulating on the radiator and being vaporized when the thermostat opens, allowing hot coolant to enter the radiator. If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check coolant freeze point in the radiator and in the coolant recovery bottle.
MAINTAINING YOUR VEHICLE Hoses and Vacuum/Vapor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage. Hard or soft spots, brittle rubber, cracking, tears, cuts, abrasions, and excessive swelling indicate deterioration of the rubber Pay particular attention to the hoses nearest to high heat sources such as the exhaust manifold. Inspect hose routing to be sure hoses do not touch any heat source or moving component that may cause heat damage or mechanical wear.
MAINTAINING YOUR VEHICLE WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency. Brake And Power Steering Hoses When servicing the vehicle for scheduled maintenance, inspect the surface of the hoses and nylon tubing for evidence of heat and mechanical damage.
MAINTAINING YOUR VEHICLE WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Master Cylinder - Brake Fluid Level Check Check the fluid level in the master cylinder immediately if the brake system warning light indicates system failure. Check the fluid level in the master cylinder when performing underhood services.
MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Do not allow petroleum base fluid to contaminate the brake fluid, all brake seal components could be damaged causing partial or complete brake failure.
MAINTAINING YOUR VEHICLE Fluid Level Check — Vehicles with 2.4L and 2.7L Engines Use the following procedure to check the automatic transaxle fluid level properly: 1. Park the vehicle on level ground. 2. Run the engine at curb idle speed for a minimum of 60 seconds. 3. Apply the parking brake fully. 4. Place the gear selector momentarily in each gear position ending with the lever in PARK. 5. Wipe the area around the dipstick clean to eliminate the possibility of dirt entering the transaxle. 6.
MAINTAINING YOUR VEHICLE CAUTION! • Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Genuine Parts” for the correct fluid type. • Dirt and water in the transaxle can cause serious damage.
MAINTAINING YOUR VEHICLE Front and Rear Wheel Bearings Front and rear wheel bearings are permanently sealed. No regular maintenance is required for these components. Appearance Care And Protection From Corrosion Protection Of Body And Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage.
MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using Mopart Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopart Super Kleen Bug and Tar Remover to remove. • Use Mopart Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint.
MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to an accident or similar cause, which destroys the paint and protective coating, have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.
MAINTAINING YOUR VEHICLE Mopart Spot & Stain Remover if absolutely necessary. Do not use harsh cleaners or Armorall. Use Mopart Total Clean to clean vinyl upholstery Cleaning Leather Upholstery Mopart Total Clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth.
MAINTAINING YOUR VEHICLE • For grease stains, apply Mopart Multi-Purpose Cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • Do not use any solvents or protectants on Yes Essentialst products. Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.
MAINTAINING YOUR VEHICLE 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye, or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water.
MAINTAINING YOUR VEHICLE CONVERTIBLE TOP CARE Soft Top Immediate removal of any contaminant is recommended. Regular washing of the top will enhance its life and appearance, and make successive cleanings easier. Do not subject the top to excessive heat. Frequently vacuum the top and storage compartment. Washing Hand washing is highly recommended. Automatic car washing equipment can damage the top material. If you must use an automatic car wash, soft cloth systems are preferred.
MAINTAINING YOUR VEHICLE Scrub in all directions, covering an area of about two square feet at a time. Avoid heavy scrubbing. Rinse the entire vehicle with water to remove all soap and dirt from the top fabric and to prevent streaking on painted and chrome surfaces. Allow the top to dry before lowering. Vacuuming the top with a wet/dry shop vacuum will decrease the top’s drying time, ensure removal of all dirt, and delete streaks in the material.
MAINTAINING YOUR VEHICLE CAUTION! Avoid getting Scotchguardt on the surrounding weather strips, moldings, paint, or glass. Damage to these items might occur. 395 FUSES (TOTALLY INTEGRATED POWER MODULE) The Totally Integrated Power Module (TIPM) is located in the engine compartment near the air cleaner assembly. This center contains fuses and relays.
MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 1 40 Amp — Green 2 — 20 Amp Yellow 3 — 10 Amp Red 4 — 5 — 6 — 7 — 10 Amp Red 20 Amp Yellow 10 Amp Red 30 Amp Green Description Battery Feed — Power Top Module — Battery Feed — Center High Mounted Stop Light (CHMSL)/ Brake Switch Battery Feed — Ignition Switch Trailer Tow – if equipped Power Mirror Switch/ Climate Controls Ignition Off Draw (IOD) Sense 1 Cavity Cartridge Mini Fuse Fuse 8 — 30 Amp Green 9 40 Amp — Green 10 — 20 Amp Ye
MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 15 40 Amp — Green 16 — 15 Amp Lt. Blue 17 — 10 Amp Red 18 40 Amp Green — 19 — 20 — 21 — 20 Amp Yellow 15 Amp Lt. Blue 10 Amp Red Description Battery Feed — Radiator Fan Relay Ignition Run/Acc — Cigar Lighter Wireless Control Module (WCM)/ Clock/Steering Control Module (SCM) Battery Feed — Auto Shutdown (ASD) Relay Power Amp Feed 2 if equipped Radio — Cavity Cartridge Mini Fuse Fuse 22 — 10 Amp Red 23 — 24 — 25 — 26 — 15 Amp Lt.
MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 27 — 10 Amp Red 28 — 10 Amp Red 29 — — 30 — 20 Amp Yellow 31 — 10 Amp Red Description Ignition Run — Occupant Classification Module (OCM)/ Occupant Restraint Controller (ORC) Ignition Run — Occupant Classification Module (OCM)/ Occupant Restraint Controller (ORC) Hot Car (No Fuse Required) Ignition Run — Heated Seats - if equipped — Cavity Cartridge Mini Fuse Fuse 32 30 Amp — Pink 33 — 10 Amp Red 34 30 Amp Pink — Description Au
MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 35 40 Amp — Green 36 30 Amp Pink — 37 — 25 Amp Clear 399 Description CAUTION! Battery Feed — AntiLock Brakes (ABS) Module - if equipped/Electronic Stability Program (ESP) Module - if equipped Battery Feed — Passenger Door Module (PDM)/Driver Door Module (DDM) Battery Feed — Power Top Module • When installing the Totally Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched.
MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you will not be using your vehicle for more than 21 days you may want to take steps to preserve your battery. You may: • Remove the IOD (Ignition Off-Draw) mini fuses from the Totally Integrated Power Module located in the engine compartment. • Or, disconnect the batter negative cable. REPLACEMENT BULBS All the inside bulbs are brass or glass wedge base. Aluminum base bulbs are not approved and should not be used for replacement.
MAINTAINING YOUR VEHICLE 401 BULB REPLACEMENT Low Beam Headlight, High Beam Headlight 1. Open the hood. NOTE: It may be necessary to remove the air cleaner filter housing and position the totally integrated power module aside prior to replacing the low beam headlight on the driver’s side of the vehicle. 2. Rotate the applicable bulb and connector assembly 1⁄4 turn counterclockwise and remove the assembly from the headlight housing. 1 — High Beam Headlight 2 — Low Beam Headlight 3.
MAINTAINING YOUR VEHICLE CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front Turn Signal/Park Light 1. Open the hood. 2. Rotate the bulb’s electrical connector 1⁄4 turn counterclockwise and remove it from the headlight housing. 4. Install the bulb and connector assembly into the headlight housing and rotate it 1⁄4 turn clockwise to lock it in place.
MAINTAINING YOUR VEHICLE 403 3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the bulb and connector assembly into the headlight housing and rotate the connector 1⁄4 turn clockwise to lock it in place. Front Fog Light NOTE: Access to the lights through the lower fascia cutout is limited. We recommend you access the lights by turning the steering wheel to allow access and remove the inner fender shield. 1.
MAINTAINING YOUR VEHICLE 2. Remove the bulb from the connector socket and install the replacement bulb. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. Tail/Stop Light, Rear Turn Signal Light, Backup Light The taillights are a two-piece design. The tail/stop lights and rear turn signal lights are located in the rear corner body panels.
MAINTAINING YOUR VEHICLE 2. Remove the two plastic wing nuts from the taillight housing. 405 4. Rotate the applicable bulb’s electrical connector 1⁄4 turn counterclockwise and remove it from the taillight housing. 7 Location Plastic Wing Nuts 3. Grasp the taillight housing with one hand on the bottom of the housing and the other hand on the inboard housing flange and pull it outward firmly to disengage the housing from the vehicle.
MAINTAINING YOUR VEHICLE 5. Remove the bulb from the connector socket and install the replacement bulb. 6. Install the bulb and connector assembly into the taillight housing and rotate the connector 1⁄4 turn clockwise to lock it in place. 7. Reinstall the taillight housing. Changing the Backup Light 1. Open the trunk. 2. Rotate the bulb’s electrical connector 1⁄4 turn counterclockwise and remove it from the housing. Backup and Rear Fog Light 3.
MAINTAINING YOUR VEHICLE 407 License Plate Light 2. Gently pry the lens loose. 1. Remove the two retaining screws from the lens. 3. Remove the bulb from the connector socket and install the replacement bulb. 4. Install the lens and the two retaining screws.
MAINTAINING YOUR VEHICLE Center High-Mounted Stop Light (CHMSL) 1. Open the trunk lid. 2. Rotate the bulb’s electrical connector 1⁄4 turn counterclockwise and remove it from the CHMSL housing. High-mounted Stop Light Bulb Replacement 3. Disconnect the bulb from the harness connector and then connect the replacement bulb. 4. Install the bulb and connector assembly into the CHMSL housing and rotate the connector 1⁄4 turn clockwise to lock it in place.
MAINTAINING YOUR VEHICLE 409 FLUIDS AND CAPACITIES Engine Fuel (approximate) All Engines Engine Oil with Filter 2.4L Engine (SAE 5W-20, API Certified) 2.7L Engine (SAE 5W-20, API Certified) 3.5L Engine (SAE 10W-30, API Certified) Cooling System * 2.4L Engine (Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent. 2.7L Engine (Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent. 3.5L Engine (Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent.
MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil (2.4L & 2.7L) Engine Oil (3.5L) Oil Filter (2.4L) Oil Filter (2.7L & 3.5L) Fluids, Lubricants, and Genuine Parts Mopart Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent Use API Certified engine oil. SAE 5W-20 is recommended. Refer to the engine oil fill cap for the correct SAE grade meeting DaimlerChrysler Material Standard MS-6395.
MAINTAINING YOUR VEHICLE 411 Component Fluids, Lubricants, and Genuine Parts Spark Plugs (2.4L) ZFR5F-11 (Gap.044 in [1.12 mm]) Spark Plugs (2.7L) RE14PMC5 (Gap.050 in [1.27 mm]) Spark Plugs (3.5L) ZFR5LP-13G (Gap.050 in [1.27 mm]) Fuel Selection (2.4L & 2.7L) 87 Octane Fuel Selection (2.7L - EXCEPT CALIE-85 Ethanol FORNIA EMISSION STATES) Fuel Selection (3.
MAINTAINING YOUR VEHICLE Chassis Component Automatic Transaxle Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts Mopart ATF+4 Automatic Transmission Fluid. Mopart DOT 3 and SAE J1703 should be used. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. Mopart ATF+4 Automatic Transmission Fluid.
MAINTENANCE SCHEDULES CONTENTS m Emission Control System Maintenance . . . . . . . . 414 m Maintenance Schedule . . . . . . . . . . . . . . . . . . . 414 ▫ Required Maintenance Intervals . . . . . . . . . . .
M A I N T E N A N C E 414 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 415 M NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicles oil if it has been 6 months since your last oil change even if the oil change indicator message is NOT illuminated.
M A I N T E N A N C E S C H E D U L E S 8 416 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check tire pressure and look for unusual wear or damage. • Change the engine oil filter. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of coolant reservoir, brake master cylinder, power steering, and automatic transaxle, and add fluid as needed.
MAINTENANCE SCHEDULES 417 M Required Maintenance Intervals Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Change the engine oil and engine oil filter. Rotate the tires. If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. Inspect the brake linings, and replace if necessary. Replace the air conditioning filter (if equipped). Inspect the CV joints.
M 418 MAINTENANCE SCHEDULES A I N T E N Maintenance Items A N Replace the spark plugs on 2.4L engines (except C PZEV* engine). E Inspect and adjust the power steering pump belt tenS C H E D U L E S 8 sion on 2.4L engines. Inspect the generator belt on 2.4L engines, and replace if necessary. Change the automatic transaxle fluid & filter if using your vehicle for any of the following: police, taxi, fleet, or frequent trailer towing. Inspect and replace the PCV valve if necessary.
MAINTENANCE SCHEDULES 419 M Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Replace the timing belt on 2.4L and 3.5L engines. Change the automatic transaxle fluid & filter. Replace the accessory drive belt on 2.7L engines. *P artial Z ero E missions V ehicle WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . 423 ▫ In Mexico Contact . . . . . . . . . . . . . . . . . . . . . 424 ▫ Prepare For The Appointment . . . . . . . . . . . . 423 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . . 425 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 423 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE m Publication Order Forms . . . . . . . . . . . . . . . . . . 428 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . 429 m Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 429 ▫ Temperature Grades . . . . . . . . . . . . . . . . . . . 430 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty; discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your authorized dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealership. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
IF YOU NEED CONSUMER ASSISTANCE WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WARRANTY INFORMATION (U.S.
IF YOU NEED CONSUMER ASSISTANCE REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C. If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes).
IF YOU NEED CONSUMER ASSISTANCE Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National Highway Traffic Safety Administration.
IF YOU NEED CONSUMER ASSISTANCE on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
INDEX 10
INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . 264,267 ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . 268 Accessory Delay, Power . . . . . . . . . . . . . . . . . . . . 12 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 377 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 316 Adding Washer Fluid . . . . . . . . . . . . . . . . . . 149,374 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Automatic Dimming Mirror . . . . . . . . . . . . . . . . . 96 Automatic Door Locks . . . . . . . . . . . . . . . . . . . . . 31 Automatic Headlights . . . . . . . . . . . . . . . . . . . . 139 Automatic Oil Change Indicator . . . . . . . . 179,189,414 Automatic Temperature Control (ATC) . . . . . . . . . 237 Automatic Transaxle . . . . . . . . . . . . . . . . 251,255,384 Adding Fluid . . . . . . . . . . . . . . . . . . . 384,385,412 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Fluid Check . . . . . . . . . . . . . . . . . . . . . . . 383,412 Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . 383 Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264 Warning Light . . . . . . . . . . . . . . . . . . . . . . . . 182 Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267,381 Brake/Transaxle Interlock . . . . . . . . . . . . . . . . . .
INDEX Cleaning Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389 Windshield Wiper Blades . . . . . . . . . . . . . . . . . 373 Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . 232 Clock . . . . . . . . . . . . . . . . . . . . . . . . 196,200,215,218 Coin Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Cold Weather Operation . . . . . . . . . . . . . . . . . . . 252 Compact Disc (CD) Maintenance . . . . . . . . . . . . . 231 Compact Spare Tire . . . . . .
INDEX Cup Holder . . . . . . . . . . . . . . . . . . . . . . . . . 164,392 Heated/Cooled (Beverage Holder) . . . . . . . . . . 164 Customer Assistance . . . . . . . . . . . . . . . . . . . . . 423 Customer Programmable Features . . . . . . . . . . . . 194 Data Recorder, Event . . . . . . . . . . . . . . . . . . . . . . 60 Daytime Brightness, Interior Lights . . . . . . . . . . . 145 Daytime Running Lights . . . . . . . . . . . . . . . . . . . 140 Dealer Service . . . . . . . . . . . . . . . . . . . .
INDEX Electric Remote Mirrors . . . . . . . . . . . . . . . . . . . . 98 Electrical Power Outlets . . . . . . . . . . . . . . . . . . . 161 Electronic Brake Control System Brake Assist System . . . . . . . . . . . . . . . . . . . . 275 Electronic Stability Program . . . . . . . . . . . . . . . 276 Traction Control System . . . . . . . . . . . . . . . . . 274 Electronic Speed Control (Cruise Control) . . . . . . 151 Electronic Stability Program (ESP) . . . . . . . . . . . .
INDEX Oil Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . 364 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . 336 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251 Temperature Gauge . . . . . . . . . . . . . . . . . . . . . 176 Engine Oil Viscosity . . . . . . . . . . . . . . . . . . . . . . 363 Enhanced Accident Response Feature . . . . . . . . . . 58 Entry System, Illuminated . . . .
INDEX Flooded Engine Starting . . . . . . . . . . . . . . . . . . . 253 Floor Console . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Fluid, Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . 412 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . . 409 Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Fluid Level Checks Automatic Transaxle . . . . . . . . . . . . . . . . . 384,385 Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Garage Door Opener (HomeLinkt) . . . . . . . . . . . 155 Gas Cap (Fuel Filler Cap) . . . . . . . . . . . . 316,318,358 Gasoline, Clean Air . . . . . . . . . . . . . . . . . . . . . . 309 Gasoline (Fuel) . . . . . . . . . . . . . . . . . . . . . . . . . 307 Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . 309 Gauges Coolant Temperature . . . . . . . . . . . . . . . . . . . . 176 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 Odometer . . . . . . . . . . . . .
INDEX Time Delay . . . . . . . . . . . . . . . . . . . . . . . . . . 140 Heated Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Heated Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232 Heater, Beverage Holder (Cup Holder) . . . . . . . . 164 Heater, Engine Block . . . . . . . . . . . . . . . . . . . . . 255 High Beam/Low Beam Select (Dimmer) Switch . . 142 Hitches Trailer Towing . . . . . . . . . . . . . .
INDEX Jacking Instructions . . . . . . . . . . . . . . . . . . . . . . 340 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . . 344 Key, Programming . . . . . Key, Replacement . . . . . Key, Sentry (Immobilizer) Key-In Reminder . . . . . . Keyless Entry System . . . Keys . . . . . . . . . . . . . . Knee Bolster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Engine Temperature Warning . . . . . . . . . . . . . . 178 Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Fog . . . . . . . . . . . . . . . . . . . . . . . . . . 141,183,403 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 336 Headlight Switch . . . . . . . . . . . . . . . . . . . 138,139 Headlights . . . . . . . . . . . . . . . . . . . . . . . . 139,401 Headlights On Reminder . . . . . . . . . . . . . . . . . 141 Headlights On With Wipers . . . . . . . . . . . .
INDEX Auto Unlock . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Automatic Door . . . . . . . . . . . . . . . . . . . . . . . . 31 Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Power Door . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Low Tire Pressure System . . . . . . . . . . . . . . . . . . 299 Lower Anchors and Tether for CHildren (LATCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66,68 Lubrication, Body . . . . . . . . . . . . . . . . . .
INDEX Occupant Restraints . . . . . . . . . . . . . . . . . 39,53,54,56 Octane Rating, Gasoline (Fuel) . . . . . . . . . . . . 307,410 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178,180 Oil Change Indicator . . . . . . . . . . . . . . . . 179,189,414 Oil Change Indicator, Reset . . . . . . . . . . . . . . 179,189 Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . 361,410 Capacity . . . . . . . . . . . . .
INDEX Phone, Cellular . . . . . . . . . . . . . . . . . . . . 99,217,218 Phone, Hands-Free (UConnect™) . . . . . . . . 99,217,218 Placard, Tire and Loading Information . . . . . . . . . 284 Port Universal Serial Bus (USB) . . . . . . . . . . . . . 213,217 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213,217 Power Accessory Delay . . . . . . . . . . . . . . . . . . . . . . . . 12 Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267 Deck Lid Release . . . . . . . . . .
INDEX Rear Window Features . . . . . . . . . . . . . . . . . . . . 246 Reception, Radio . . . . . . . . . . . . . . . . . . . . . . . . 197 Recorder, Event Data . . . . . . . . . . . . . . . . . . . . . . 60 Recreational Towing . . . . . . . . . . . . . . . . . . . . . . 333 Reformulated Gasoline . . . . . . . . . . . . . . . . . . . . 309 Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370 Release, Hood . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Reminder, Lights On . . . .
INDEX Seat Belt Maintenance . . . . . . . . . . . . . . . . . . . . 392 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . 45,46 Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . 39,40,75 And Pregnant Women . . . . . . . . . . . . . . . . . . . 47 Child Restraint . . . . . . . . . . . . . . . . . . . 62,63,64,69 Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Front Seat . . . . . . . . . . . . . . . . . . . . . . . . . . 40,41 Inspection . . . . . . . . . .
INDEX Side Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Side View Mirror Adjustment . . . . . . . . . . . . . . . . 97 Side Window Demisters (Defrosters) . . . . . . . . . . 244 Signals, Turn . . . . . . . . . . . . . . . . . . . . . . 76,142,404 Slippery Surfaces, Driving On . . . . . . . . . . . . . . . 271 Snow Chains (Tire Chains) . . . . . . . . . . . . . . . . . 297 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298 Sound Systems (Radio) . . . . . . . . . .
INDEX Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 Taillights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404 Telescoping Steering Column . . . . . . . . . . . . . . . 150 Temperature Control, Automatic (ATC) . . . . . . . . 237 Temperature Gauge, Engine Coolant . . . . . . . 176,337 Tether Anchor, Child Restraint . . . . . . . . . . . . . . . 66 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . . 150 Time Delay, Headlight . . . . . . . . . . . . .
INDEX To Open Hood . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Tongue Weight/Trailer Weight . . . . . . . . . . . . . . 326 Tonneau Cover . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322 Behind a Motor Home . . . . . . . . . . . . . . . . . . 333 Disabled Vehicle . . . . . . . . . . . . . . . . . . . . . . . 349 Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325 Recreational . . . . . . . . . . . .
INDEX Transmitter, Garage Door Opener (HomeLinkt) . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 Transmitter Programming (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 21 Transmitter, Remote Keyless Entry (RKE) . . . . . . . . 21 Transporting Pets . . . . . . . . . . . . . . . . . . . . . . . . 72 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . 294 Trip Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . 178 Trip Odometer Reset Button . . . . . . . . .
INDEX Warning Lights (Instrument Cluster Description) . . . . . . . . . . . . . 176 Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . 6 Warranty Information . . . . . . . . . . . . . . . . . . . . . 426 Washer, Adding Fluid . . . . . . . . . . . . . . . . . . 149,374 Washers, Windshield . . . . . . . . . . . . . . . . 146,149,374 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 388 Water Driving Through . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION HOW TO USE THIS MANUAL WARNINGS AND CAUTIONS VEHICLE IDENTIFICATION NUMBER VEHICLE MODIFICATIONS / ALTERATIONS THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key RemovalKey-In-Ignition ReminderSENTRY KEY Replacement KeysSentry Key ProgrammingGeneral InformationSECURITY ALARM SYSTEM - IF EQUIPPED Rearming of the SystemTo Arm the SystemTo Disarm the SystemILLUMINATED ENTRY SYSTEM - IF EQUIPPED REMOTE KEYLESS ENTRY To unlock the doorsTo lock the doorsConve
