2009 300 300 2009 owner’s manual Chrysler LLC 81-026-0943 147915 09 LX300C OM.indd 1 Second Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 6 ..............
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is on the left front corner of the instrument panel.
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 䡵 Vehicle Security Alarm — If Equipped . . . . . . . . 18 ▫ Wireless Ignition Node (WIN) . . . . . . . . . . . . 12 ▫ Rearming Of The System . . . . . . . . . . . . . . . . 18 ▫ Integrated Ignition Key . . . . . . . . . . . . . . . . . 13 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . 18 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . 13 ▫ To Disarm The System .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 24 䡵 Trunk Lock And Release ▫ Programming Additional Transmitters . . . . . . 25 䡵 Trunk Safety Warning . . . . . . . . . . . . . . . . . . . 40 ▫ Transmitter Battery Service . . . . . . . . . . . . . . 25 ▫ Trunk Emergency Release . . . . . . . . . . . . . . . 40 ▫ General Information . . . . . . . . . . . . . . . . . . . 26 䡵 Occupant Restraints . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Event Data Recorder (EDR) . . . . . . . . . . . . . . 63 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . 76 ▫ Child Restraints . . . . . . . . . . . . . . . . . . . . . . 65 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 䡵 Engine Break-In Recommendations . . . . . . . . . . 75 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 ▫ Transporting Passengers .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Remote Keyless Entry (RKE) transmitter with Integrated Key and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the doublesided integrated key into the ignition switch with either side up. Wireless Ignition Node (WIN) The Wireless Ignition Node (WIN) operates similar to an ignition switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Integrated Ignition Key The Integrated Key (FOBIK) operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and a valet key, which stores in the rear of the RKE transmitter. 2 The valet key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead. The valet key is also for locking the glove box. You can keep the valet key with you when valet parking.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for 10 minutes after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 NOTE: The Key-In-Ignition reminder only sounds when the ignition key is placed in the LOCK or ACC position. SENTRY KEY姞 The Sentry Key威 Immobilizer system prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Exxon/Mobil Speedpass™, additional RKE transmitters, or any other transponder-equipped components on the same key chain will not cause a fault unless the additional part is physically held against the RKE transmitter being used to start the vehicle. Cell phones, pagers, or other Radio Frequency (RF) electronics will not cause interference with this system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Customer Key Programming If you have two valid RKE transmitters with integrated keys, you can program new RKE transmitters to the system by performing the following procedure: 1. Insert the first valid integrated key into the ignition switch and turn the ignition switch to the ON position for at least three seconds, but no longer than 15 seconds. Turn the ignition switch to the LOCK position and remove the first key. 2.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information The Sentry Key威 system complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received, including interference that may cause undesired operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 the Vehicle Security Alarm will cancel the arming process. If you wish to rearm the Vehicle Security Alarm after closing the door, you must repeat one of the previouslydescribed arming sequences. To Disarm the System Either press the UNLOCK button on the RKE transmitter or insert a valid ignition key into the ignition switch and turn the key to the ON position.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tamper Alert If something has triggered the Vehicle Security Alarm in your absence, the horn will sound three times when you disarm the Vehicle Security Alarm. Check the vehicle for tampering. ILLUMINATED ENTRY SYSTEM The courtesy lights will turn on when you use the Remote Keyless Entry (RKE) transmitter or open any door. This feature also turns on the approach lighting in the outside mirrors (if equipped).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Remote Key Unlock, Driver Door/All Doors 1st Press This feature lets you program the system to unlock either the driver’s door or all doors on the first press of the UNLOCK button on the RKE transmitter.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Release both buttons at the same time. 3. Test the feature while outside of the vehicle by pressing the LOCK/UNLOCK buttons on the RKE transmitter with the ignition switch in the LOCK position and the key removed. 4. Repeat these steps if you want to return this feature to its previous setting. NOTE: Pressing the LOCK button on the RKE transmitter while you are inside the vehicle will activate the security alarm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 4. Repeat these steps if you want to return this feature to its previous setting. NOTE: Pressing the LOCK button on the RKE transmitter while you are in the vehicle will activate the security alarm. Opening a door with the security alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the security alarm.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Press the LOCK button on a programmed RKE transmitter for at least four seconds, but no longer than 10 seconds. Then, press the PANIC button while still holding the LOCK button. 2. Release both buttons at the same time. 3. Test the feature while outside of the vehicle by pressing the LOCK button on the RKE transmitter with the ignition switch in the LOCK position and the key removed. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 • You may need to be less than 35 ft (11 m) from the vehicle when using the RKE transmitter to turn off the Panic Alarm due to the radio frequency noises emitted by the system. 2 Programming Additional Transmitters Refer to Sentry Key威 “Customer Key Programming.” If you do not have a programmed RKE transmitter, contact your authorized dealer for details. Transmitter Battery Service The recommended replacement battery is one CR2032 battery.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Reposition the access door panel over the battery opening and snap into place. 1. A weak battery in the RKE transmitter. The expected life of the battery is a minimum of three years. General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 • Doors closed • Hood closed • Trunk closed • Hazard switch off • Brake switch inactive (brake pedal not pressed) • Ignition key removed from ignition switch • Battery at an acceptable charge level • RKE PANIC button not pressed To Enter Remote Start Mode Press and release the REMOTE START button on the RKE transmitter twice, within five seconds. The parking lights will flash and the horn will chirp twice (if programmed).
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To avoid unintentional shut downs, the system will disable the one time press of the REMOTE START button for two seconds after receiving a valid Remote Start request. To Exit Remote Start Mode and Drive the Vehicle Before the end of the 15-minute cycle, press and release the UNLOCK button on the RKE transmitter to unlock the doors and disarm the Vehicle Security Alarm (if equipped).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 WARNING! Door Lock Plunger If the door lock plunger is down when you shut the door, the door will lock. Make sure the key is not inside the vehicle before closing the door. • For personal security and safety in the event of an accident, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • When leaving the vehicle, always remove the key from the ignition and lock your vehicle.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. you from accidentally locking the key in the vehicle. Removing the key, returning the ignition mode to the OFF position, or closing the door will allow the locks to operate. If a door is open, the key is in the ignition LOCK, or ACC position, a chime will sound as a reminder to remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 6. The doors were not previously locked using the power door lock switch or Remote Keyless Entry (RKE) transmitter. 2. Cycle the ignition switch between LOCK and ON and then back to LOCK four times ending up in the LOCK position (do not start engine). Automatic Door Locks Programming The Automatic Door Locks feature can be enabled or disabled as follows: 3. Depress the power door LOCK switch to lock the doors.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The transmission was in gear and the vehicle speed returned to 0 mph (0 km/h). 3. The transmission is in NEUTRAL or PARK. 4. The driver door is opened. 5. The doors were not previously unlocked, and 6. The vehicle speed is 0 mph (0 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 To Engage the Child Protection Door Lock System 1. Open the rear door. 2 2. Insert the tip of the valet key (or similar object) into the child lock control and pull it upward. NOTE: For valet key information, refer to “A Word About Your Keys” in this section. Child Lock Control 3. Repeat Steps 1 and 2 for the opposite rear door.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. Failure to follow this warning may result in serious injury or death. To Disengage the Child Protection Door Lock System 1. Open the rear door. 2. Insert the tip of the valet key (or similar object) into the child lock control and pull it downward.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 3. Repeat Steps 1 and 2 for the opposite rear door. NOTE: After disengaging the Child Protection Door Lock system, always test the door from the inside to make certain it is in the desired position. 2 WINDOWS Power Windows The window controls on the driver’s door control all the door windows. Power Window Switches There are single window controls on each passenger door trim panel, which operate the passenger door windows.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. AUTO-Down Feature The driver door power window switch and some model passenger door power window switches have an AUTOdown feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 AUTO-Up Feature with Anti–Pinch Protection — If Equipped Lift the window switch to the second detent, release, and the window will go up automatically. programmable. Refer to “Delay Power Off to Accessories Until Exit,” under “Personal Settings (CustomerProgrammable Features)” in the “Electronic Vehicle Information Center (EVIC),” in Section 4 of this manual.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing. Window Lockout Switch The window lockout switch on the driver’s door trim panel allows you to disable the window controls on the passenger doors. To disable the window controls, press and release the window lockout button (setting it in the DOWN position).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 1. Pull the window switch up to close window completely and continue to hold the switch up for an additional two seconds after the window is closed. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The trunk lid can be released from outside the vehicle by pressing the TRUNK button on the Remote Keyless Entry (RKE) transmitter twice within five seconds. With the ignition switch in the ON position, the Trunk Open symbol will display in the instrument cluster indicating that the trunk is open. The odometer display will reappear once the trunk is closed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 and passengers seated next to a window, and the optional supplemental front seat-mounted side airbags. If you will be carrying children too small for adult-size belts, your seat belts also can be used to hold infant and child restraint systems. Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WARNING! (Continued) • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision best. • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Inserting Latch Plate into Buckle WARNING! • A belt that is buckled into the wrong buckle will not protect you properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 WARNING! (Continued) • A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up a bit on the shoulder belt.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision, it could even cut into you. Be sure the belt is straight.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 In the rear seat, move toward the center of the seat to position the belt away from your neck. Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 degrees to create a fold that begins immediately above the latch plate.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove any slack from the seat belts in the event of a collision. These devices improve the performance of the seat belt system by assuring that the belt is tight around the occupant in a collision. Pretensioners work for all size occupants, including those in child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 NOTE: Chrysler LLC does not recommend deactivating the BeltAlert威. 1. With all doors closed, and the ignition switch in any position except ON or START, buckle the driver’s seat belt. 2. Turn the ignition switch to the ON position, but do not start the engine. Wait for the Seat Belt Reminder Light to turn off and then proceed to the next step.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE that have the Automatic Locking mode feature have a distinctive label on the webbing. Children 12 years old and younger should be properly restrained in the rear seat whenever possible. Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the seat belt is not long enough when it is worn low and snug and in the recommended seating positions. Remove and store the extender when not needed. Driver and Front Passenger Supplemental Restraint System (SRS) - Airbag This vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt restraint systems.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity. WARNING! • Do not put anything on or around the front airbag covers or attempt to open them. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 If the vehicle is equipped with supplemental front seatmounted side airbags, they are marked with an SRS label sewn into the outboard side of the seat. Window Airbag NOTE: Airbag covers may not be obvious in the interior trim, but they will open to allow airbag deployment.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • If your vehicle is equipped with supplemental front seat-mounted side airbags, do not use accessory seat covers or place objects between you and the seat airbags; the performance could be adversely affected and/or objects could be pushed into you, causing serious injury. • If your vehicle is equipped with supplemental front seat-mounted side airbags, do not attach cupholders or any other objects on or around the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Side curtain and seat airbags also work with seat belts to improve occupant protection. While the seat belts are designed to protect you in many types of collisions, the front airbags will deploy in moderate to severe frontal collisions.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seat as far back as possible and use the proper child restraint. (Refer to information on Child Restraints in this section.) 5. You should read the instructions provided with your child restraint to make sure that you are using it properly. 6. All occupants should use their seat belts properly. 7. The driver and front passenger seats should be moved back as far as practical to allow the airbags time to inflate. 8.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Airbag System Components The airbag system consists of the following: • Occupant Restraint Controller (ORC) • Side Remote Acceleration Sensors (if equipped) • Airbag Warning Light • Driver Airbag • Front Passenger Airbag • Supplemental Side Curtain Airbags above Side Windows (if equipped) • Supplemental Front Seat-Mounted Side Airbags (if equipped) • Steering Wheel and Column • Instrument Panel • Interconnecting Wiring • Seat Belt Reminder Light • Knee Impact
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or ON positions. These include all of the items listed above except the knee bolster, the instrument panel, and the steering wheel and column. If the key is in the LOCK position, in the ACC position, or not in the ignition, the airbags are not on and they will not inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 their full size. The bags fully inflate in about 50 to 70 ms. This is about half of the time that it takes to blink your eyes. The bags then quickly deflate while helping to restrain the driver and front passenger. The driver’s front airbag gas is vented through vent holes in the sides of the airbag. The passenger’s front airbag gas is vented through vent holes in the sides of the airbag.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE between the occupant and the door. The airbag inflates at a very high speed and with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the front seat-mounted side airbag inflates. This especially applies to children. The following requirements must be strictly adhered to: • Do not make any modifications to the front seat components, assembly, or to the seat cover in any way.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 If a Deployment Occurs The airbag system is designed to deploy when the ORC detects a moderate to severe collision to help restrain the driver and front passenger and then to immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Deployed airbags can’t protect you in another collision. Have the airbags replaced by an authorized dealer as soon as possible. • Unlocks the doors automatically. NOTE: The interior lights can only be deactivated if the key is removed from the ignition switch or the vehicle is driven.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 WARNING! (Continued) • You need proper knee impact protection in a collision. Do not mount or locate any aftermarket equipment on or behind the knee impact bolster. • It is dangerous to try to repair any part of the airbag system yourself. Be sure to tell anyone who works on your vehicle that it has airbags. NOTE: Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: 1. A near-deployment event occurs when the airbag sensor detects severe vehicle deceleration usually indicative of a crash, but not severe enough to warrant airbag deployment. 2. Under certain circumstances, EDR data may not be recorded (e.g., loss of battery power).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 1. Used for research purposes, such as to match data with a particular crash record in an aggregate database, provided confidentiality of personal data is thereafter preserved. • Airbag deployment level (if applicable) 2. Used in defense of litigation involving a Chrysler LLC product. • Brake status (service and parking brakes) 3. Requested by police under a legal warrant. • Engine control status (including engine speed) 4. Otherwise required by law.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years and younger should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front. There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 infant carriers do, so they can be used rearward-facing by children who weigh more than 20 lbs (9 kg) but are less than one year old. Both types of child restraints are held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system. Refer to “LATCH — Child Seat Anchorage System (Lower Anchors and Tether for CHildren)” in this section.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE over the front of the seat when their back is against the seatback should use the lap/shoulder belt in a rear seat. • Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may not work when you need it.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE kits or retrofit kits. You are urged to take advantage of all the available attachments provided with your child restraint in any vehicle. All three rear-seating positions have lower anchorages that are capable of accommodating LATCH-compatible child seats. You should NEVER install LATCHcompatible child seats so that two seats share a common lower anchorage.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Again, carefully follow the installation instructions that are provided with the child restraint system. The rear seat lower anchorages are round bars located at the rear of the seat cushion where it meets the seatback and are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • Ensure that the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. • When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children. It is recommended that before installing the child restraint, buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Seat belts with an automatic locking retractor have a distinctive label on the seat belt webbing. The seat belt must be in the Automatic Locking mode in order to enable a child restraint to be tightly installed. Refer to “Automatic Locking Mode” in this section. A locking clip should not be necessary once the automatic locking feature is enabled. Position the shoulder and lap belt on the child restraint.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To attach a child restraint tether strap: 1. Rotate the cover over the anchor directly behind the seat where you are placing the child restraint. 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. 3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and remove slack in the tether strap according to the child restraint manufacturer’s instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your vehicle. Drive moderately during the first 300 miles (500 km).
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS Exhaust Gas Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 If you are required to drive with the trunk/liftgate open, make sure that all windows are closed and the climate control BLOWER switch is set at high speed. DO NOT use the recirculation mode. The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable. Periodic Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 85 ▫ Automatic Dimming Inside Mirror — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 3 ▫ Outside Mirrors With Turn Signal And Approach Lighting — If Equipped . . . . . . . . . 87 ▫ Tilt Mirrors In Reverse — If Equipped . . . . . . 88 ▫ Power Mirrors . . . . . . . . . . . . . . . . . . . . . . .
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ uconnect威 phone Features . . . . . . . . . . . . . . 102 ▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . 127 ▫ Advanced Phone Connectivity . . . . . . . . . . . 107 ▫ Heated Seats — If Equipped . . . . . . . . . . . . 127 ▫ Things You Should Know About Your uconnect威 phone . . . . . . . . . . . . . . . . . . . . . 109 ▫ Folding Rear Seat . . . . . . . . . . . . . . . . . . . . 129 ▫ General Information . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 ▫ Automatic Headlights — If Equipped . . . . . . 137 ▫ Mist Feature . . . . . . . . . . . . . . . . . . . . . . . . 145 ▫ Headlights On With Wipers (Available With Auto Headlights Only) . . . . . . . . . . . . . . . . 137 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . 145 ▫ SmartBeams — If Equipped . . . . . . . . . . . . . 138 ▫ Headlights On With Wipers (Available With Auto Headlights Only) . . . . . . . . . . . . . . . .
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . 152 ▫ Setting The Following Distance In ACC . . . . 162 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . 152 ▫ Adaptive Cruise Control (ACC) Menu . . . . . 164 ▫ To Accelerate For Passing . . . . . . . . . . . . . . 153 ▫ Display Warnings And Maintenance . . . . . . . 168 䡵 Adaptive Cruise Control (ACC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 ▫ Gate Operator/Canadian Programming . . . . 185 ▫ Sunshade Operation . . . . . . . . . . . . . . . . . . 190 ▫ Using HomeLink威 . . . . . . . . . . . . . . . . . . . 186 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . 190 ▫ Reprogramming A Single HomeLink威 Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . 190 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . .
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Cargo Area Features . . . . . . . . . . . . . . . . . . . 198 ▫ Rear Window Defroster . . . . . . . . . . . . . . . . 198 ▫ Trunk Mat — If Equipped . . . . . . . . . . . . . . 198 䡵 Load Leveling System — If Equipped . . . . . . . 199 䡵 Rear Window Features . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. The mirror should be adjusted while set in the day position (toward the windshield). 3 Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic and a slight overlap of the view obtained from the inside mirror. NOTE: The passenger-side convex outside mirror will give a much wider view to the rear, and especially of the lane next to your vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Outside Mirrors Folding Feature — If Equipped Some models have outside mirrors that are hinged. The hinge allows the mirror to pivot forward and rearward to resist damage. The hinge has three detent positions, full forward, full rearward and normal. Outside Mirror Auto Dimmer — If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tilt Mirrors in Reverse — If Equipped Tilt Mirrors in Reverse provides automatic outside mirror positioning which will aid the driver’s view of the ground rearward of the front doors. The outside mirrors will move slightly downward from the present position when the vehicle is shifted into the REVERSE position. The outside mirrors will then return to the original position when the vehicle is shifted out of the REVERSE position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 After selecting a mirror, move the knob in the same direction you want the mirror to move. Use the center off position to guard against accidentally moving a mirror position. NOTE: For vehicles equipped with Driver Memory Seat, you can use your RKE transmitter or the memory switch on the driver’s door trim panel to return the power mirrors to pre-programmed positions. Refer to “Driver Memory Seat” in this Section for further information.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE uconnect姞 phone — IF EQUIPPED NOTE: The sales code RER and REU radios contain an integrated uconnect威 phone. Refer to your “Navigation User’s Manual” for uconnect威 phone operating instructions for these radios. Radio sales code can be located on the lower right corner of the Radio faceplate. uconnect威 phone is a voice-activated, hands-free, invehicle communications system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s uconnect威 phone. The uconnect威 phone allows up to seven cellular phones to be linked to the system. Only one linked (or paired) cellular phone can be used with the system at a time. The system is available in English, Spanish, or French languages. The uconnect威 phone can be used with any Hands-Free Profile certified Bluetooth威 cellular phone.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE menu structure. Voice commands are required after most uconnect威 phone prompts. You will be prompted for a specific command and then guided through the available options. • Prior to giving a voice command, one must wait for the beep, which follows the ⬙Ready⬙ prompt or another prompt. • For certain operations, compound commands can be used.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Cancel Command At any prompt, after the beep, you can say ⬙Cancel⬙ and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. Pair (Link) uconnect威 phone to a Cellular Phone To begin using your uconnect威 phone, you must pair your compatible Bluetooth威 enabled cellular phone. To complete the pairing process, you will need to reference your cellular phone Owner’s Manual.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE phone to use if multiple cellular phones are in the vehicle at the same time. For example, if priority three and priority five phones are present in the vehicle, the uconnect威 phone will use the priority three cellular phone when you make a call. You can select to use a lower priority cellular phone at any time (refer to ⬙Advanced Phone Connectivity⬙ in this section). Dial by Saying a Number • Press the PHONE button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 • The uconnect威 system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios. Add Names to Your uconnect威 Phonebook NOTE: Adding names to the uconnect威 phonebook is recommended when the vehicle is not in motion. • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook New Entry.⬙ • When prompted, say the name of the new entry.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phonebook Download – Automatic Phonebook Transfer From Cellular Phone If equipped and specifically supported by your phone, uconnect威 phone automatically downloads names (text names) and number entries from the cellular phone’s phonebook. Specific Bluetooth威 Phones with Phone Book Access Profile may support this feature. See uconnect威 website for supported phones.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Phonebook Download — Single Entry If equipped and supported by your phone, uconnect威 phone allows the user to download entries from their phone via Bluetooth威. To use this feature, press the PHONE button and say “Phonebook Download.” The system prompts, “Ready to accept “V” card entry via Bluetooth威…” The system is now ready to accept phonebook entries from your phone using the Bluetooth威 Object Exchange Profile (OBEX).
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, cellular, or pager) that you wish to edit. • When prompted, recite the new phone number for the phonebook entry that you are editing. After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or return to the main menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 • After you enter the name, the uconnect威 phone will ask you which designation you wish to delete: home, work, cellular, pager, or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted. • Automatic downloaded phonebook entries cannot be deleted or edited. Delete/Erase “All” uconnect威 Phonebook Entries • Press the PHONE button to begin.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The uconnect威 phone will then prompt you as to the number designation you wish to call. • The selected number will be dialed. Phone Call Features The following features can be accessed through the uconnect威 phone if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the uconnect威 phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 or ⬙Call⬙ followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to ⬙Toggling Between Calls⬙ in this section. To combine two calls, refer to ⬙Conference Call⬙ in this section. Place/Retrieve a Call From Hold To put a call on hold, press the PHONE button until you hear a single beep. This indicates that the call is on hold.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE hold may not become active automatically. This is cell phone-dependent. To bring the call back from hold, press and hold the PHONE button until you hear a single beep. Redial • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Redial.⬙ • The uconnect威 phone will call the last number that was dialed from your cellular phone. NOTE: This may not be the last number dialed from the uconnect威 phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 • After the ⬙Ready⬙ prompt and the following beep, say the name of the language you wish to switch to English, Espanol, or Francais. If the phone is not reachable and the uconnect威 phone is operational, you may reach the emergency number as follows: • Continue to follow the system prompts to complete the language selection. • Press the PHONE button to begin. After selecting one of the languages, all prompts and voice commands will be in that language.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If supported, this number may be programmable on some systems. To do this, press the PHONE button and say ‘Setup’, followed by ‘Emergency’. • The uconnect威 phone does slightly lower your chances of successfully making a phone call as to that for the cell phone directly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Voice Mail Calling To learn how to access your voice mail, refer to ⬙Working with Automated Systems.⬙ Working with Automated Systems This method is used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated telephone system. You can use your uconnect威 phone to access a voice mail system or an automated service, such as a paging service or automated customer service line.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature. Barge In - Overriding Prompts The “Voice Recognition” button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately. For example, if a prompt is asking ⬙Would you like to pair a phone, clear a...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 phone, the audio will be played through your vehicle’s audio system. The uconnect威 phone will work the same as if you dial the number using voice recognition. NOTE: Certain brands of cellular phones do not send the dial ring to the uconnect威 phone to play it on the vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number the user may feel that the call did not go through even though the call is in progress.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you would like to connect or disconnect the Bluetooth威 connection between a uconnect威 phone paired cellular phone and the uconnect威 phone, follow the instructions described in your cellular phone User’s Manual. Select Another Cellular Phone This feature allows you to select and start using another phone paired with the uconnect威 phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing.⬙ • At the next prompt, say ⬙Delete⬙ and follow the prompts. phone Voice Training feature may be used. To enter this training mode, follow one of the two following procedures: From outside the uconnect威 phone mode (e.g., from radio mode): • You can also press the VOICE RECOGNITION button at any time while the list is being played, and then choose the phone you wish to delete.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To restore the Voice Recognition system to factory default settings, enter the Voice Training session via the above procedure and follow the prompts. Voice Recognition (VR) • For best performance, adjust the rearview mirror to provide at least 1⁄2 in (1 cm) gap between the overhead console (if equipped) and the mirror. • Always wait for the beep before speaking.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 • Phonebook (Downloaded and uconnect威 phone Local) name recognition rate is optimized when the entries are not similar. • You can say ⬙O⬙ (letter ⬙O⬙) for ⬙0⬙ (zero). ⬙800⬙ must be spoken ⬙eight-zero-zero.⬙ • smooth road surface, • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Bluetooth威 Communication Link Cellular phones have been found to lose connection to the uconnect威 phone. When this happens, the connection can generally be reestablished by switching the phone off/on. Your cellular phone is recommended to remain in Bluetooth威 ON mode. Power-Up After switching the ignition key from OFF to either the ON or ACC position, or after a language change, you must wait at least five seconds prior to using the system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 3
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 3
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call uconnect威 Tutorial try again voice training work yes 3
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 When you press the VR button, you will hear a beep. The beep is your signal to give a command. NOTE: If you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the VR button, listen for the beep, and say your command. Pressing the VR button while the system is speaking is known as “barging in.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Commands The Voice Recognition system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the Volume 1. Start a dialogue by pressing the VR button. 2. Say a command (e.g., “Help”).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Radio FM To switch to the FM band say “FM” or “Radio FM”.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memo To switch to the voice recorder mode say “Memo”. In this mode, you may say the following commands: • “New Memo” (to record a new memo) — During the recording you may press the VR button to stop recording. You proceed by saying one of the following commands: − “Previous” (to play the previous memo) − “Delete” (to delete a memo) • “Delete All” (to delete all memos) System Setup To switch to system setup say “Setup”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 NOTE: Keep in mind that you have to press the VR button first and wait for the beep before speaking the “Barge In” commands. Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers, uconnect威 phone Voice Training feature may be used. 1. Press the VR button, say “System Setup” and once you are in that menu then say “Voice Training.” This will train your own voice to the system and will improve recognition.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Power Seats The power seat switch is located on the outboard side of the seat near the floor. Use this switch to move the driver’s seat up or down, forward or rearward or to recline the seat. The passenger’s seat will move up or down, forward or rearward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 WARNING! The recliner control is located on the outboard side of the seat. Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. 3 CAUTION! Do not place any article under a power seat as it may cause damage to the seat controls.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. Lumbar Support This feature allows you to increase or decrease the amount of lumbar support. Turn the control lever forward to increase and rearward to decrease the desired amount of lumbar support.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjust the restraint so that the upper edge is as high as practical. To raise it, pull upward on the head restraint. To lower it, press the button on the post guide and push downward on the head restraint. Heated Seats — If Equipped This feature heats the front driver and passenger seats.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE On vehicles equipped with rear heated seats, the seats closest to the doors are heated. The controls for these seats are located on the rear of the center console. Press the switch once to select High-level heating. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off. Two indicators will illuminate for High, one for Low, and none for Off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods. • Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. • The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 2. Adjust all memory profile settings to desired preferences (i.e., seat, side mirror, adjustable pedals [if equipped], power tilt and telescopic steering column [if equipped], and radio station presets). 3. Press and release the SET (S) button on the memory switch. 4. Within five seconds, press and release the memory button 1 or 2. The Electronic Vehicle Information Center (EVIC) (if equipped) will display which memory position has been set.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE to “Personal Settings (Customer-Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4. accordingly. ⬙Memory Profile Set” (1 or 2) will display in the instrument cluster on vehicles equipped with the EVIC.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 To recall the memory settings for driver one, press MEMORY button number 1 on the driver’s door or the UNLOCK button on the RKE transmitter linked to memory position 1. To recall the memory setting for driver two, press MEMORY button number 2 on the driver’s door or the UNLOCK button on the RKE transmitter linked to memory position 2. A recall can be cancelled by pressing any of the MEMORY buttons (S, 1, or 2) on the driver’s door during a recall.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When you remove the key from the ignition switch, the driver seat will move about 2.4 in (60 mm) rearward if the driver seat position is greater than or equal to 2.7 in (67.7 mm) forward of the rear stop. The seat will return to its previously set position when you insert the key into the ignition switch and turn it out of the LOCK position. • When you remove the key from the ignition switch, the driver seat will move to a position 0.3 in (7.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood. 1. Pull the hood release lever located under the left side of the instrument panel. 2. Move to the outside of the vehicle and push the safety catch to the left. The safety catch is located under the center front edge of the hood. 3 Hood Safety Catch Hood Release Lever Use the hood prop rod (if equipped) to secure the hood in the open position.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood, until it is open approximately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged. WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. You could have a collision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch counterclockwise to the AUTO (A) position. When the system is on, the headlight time delay feature is also on. This means the headlights will stay on for up to 90 seconds after you turn the ignition switch OFF.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Headlights On with Wipers feature can be turned on or off through the Electronic Vehicle Information Center (EVIC) (if equipped). Refer to ”Headlights On with Wipers,” under “Personal Settings (CustomerProgrammable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 1. Pull the multifunction lever toward you to switch the headlights from the high beam to the low beam position. 2. Rotate the headlight switch clockwise from the AUTO (A) to the ON position. NOTE: Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights — If Equipped The high beam headlights will come on as Daytime Running Lights whenever the ignition switch is ON, the headlights are off and the parking brake is off. The headlight switch must be used for normal nighttime driving. Lights-On Reminder If the headlights or parking lights are on after the ignition is turned OFF, a chime will sound to alert the driver when the driver’s door is opened.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Moving the multifunction lever up or down also causes the corresponding turn signal indicator in the outside mirror (if so equipped) to flash. For details, refer to “Outside Mirrors with Turn Signal & Approach Lighting” under “Mirrors” in this Section. You can also signal a lane change by moving the multifunction lever partially up or down without moving beyond the detent. Releasing the lever at the detent will provide three flashes.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE High Beam/Low Beam Select Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever toward you to switch the headlights back to low beam. Flash-to-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will cause the headlights to turn on at high beam and remain on until the multifunction lever is released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 because a door is open. This includes the glove box light, but not the trunk light. To restore interior light operation, either turn the ignition switch ON or cycle the light switch. Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE position. The multifunction lever is located on the left side of the steering column. CAUTION! Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper switch is left in any position other than off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Mist Feature Lightly push the multifunction lever inward (toward the steering column) to activate a single wipe cycle to clear off road mist or spray from a passing vehicle.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Wipers,” under “Personal Settings (CustomerProgrammable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4. NOTE: • The rain sensing feature will not operate when the wiper speed is in the low or high position. Rain Sensing Wipers — If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 • Low Temperature Wipe Inhibit — The rain sensing feature will not operate when the ignition is first switched ON, and the vehicle is stationary, and the outside temperature is below 32°F (0°C), unless the wiper control on the multifunction lever is moved, or the vehicle speed becomes greater than 0 mph (0 km/h), or the outside temperature rises above freezing.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE outward or push it inward as desired. To lock the steering column in position, push the control handle inward until fully engaged. WARNING! Do not adjust the steering wheel while driving. The telescoping adjustment must be locked while driving. Adjusting the steering wheel while driving or driving without the telescoping adjustment locked could cause the driver to lose control of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 transmitter or the memory switch on the driver’s door trim panel to return the tilt/telescopic steering column to pre-programmed positions. Refer to “Driver Memory Seat” in this section. wheel. The switch is located on the front side of the driver’s seat cushion side shield. 3 WARNING! Moving the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The pedals can be adjusted with the ignition OFF. • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control is on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 To Activate Push and release the ON/OFF button located on the end of the Electronic Speed Control lever. The indicator light in the instrument cluster will illuminate to show that the speed control system is on. To turn the system off, push and release the ON/OFF button again. The system and the indicator light will turn off.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Set At A Desired Speed When the vehicle reaches the speed desired, push the lever downward to SET DECEL and release. Remove your foot from the accelerator pedal and the vehicle will operate at the selected speed. NOTE: • Electronic Speed Control will only function in 3rd, 4th, or 5th gear when in the Autostick威 mode (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Tapping the Electronic Speed Control lever to RESUME ACCEL once will result in a 1 mph (1.6 km/h) speed increase. Each time the Electronic Speed Control lever is tapped speed increases, so tapping the Electronic Speed Control lever three times will increase speed by 3 mph (4.8 km/h), etc. To decrease speed while Electronic Speed Control is set, push down and hold the Electronic Speed Control lever in SET DECEL.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions and you could lose control. An accident could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 WARNING! WARNING! (Continued) • Adaptive Cruise Control (ACC) is a convenience system. It is not a substitute for active driving involvement. It is always the driver’s responsibility to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead; and, most importantly, brake operation to ensure safe operation of the vehicle under all road conditions.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! You should switch off the ACC system: • When driving in fog, heavy rain, heavy snow, sleet, heavy traffic, and complex driving situations (i.e., in highway construction zones). • When entering a turn lane or highway off ramp; when driving on roads that are winding, icy, snow-covered, slippery, or have steep uphill or downhill slopes; and when towing a trailer. • When circumstances do not allow safe driving at a constant speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 When the system is turned on and in the READY state, the Electronic Vehicle Information Center (EVIC) displays “ACC READY.” When the system is OFF, the EVIC displays “CRUISE OFF.” NOTE: You cannot enable ACC under the following conditions: • When you apply the brakes. • When the parking brake is set.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate Push and release the ON/OFF/MODE button located on the end of the speed control lever. The ACC menu in the EVIC displays “ACC READY.” WARNING! Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 • The system will not be controlling the distance between your vehicle and the vehicle ahead. The vehicle speed will only be determined by the position of the accelerator pedal. 3 Remove your foot from the accelerator pedal. If you do not, the vehicle may continue to accelerate beyond the set speed. If this occurs: • The message “DRIVER OVERRIDE” will display in the EVIC.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You softly tap the brake pedal. • You depress the brake pedal. • You pull the speed control lever toward you to CANCEL. • The Electronic Stability Program/Traction Control System (ESP/TCS) activates. To Turn Off The system will turn off and erase the set speed in memory if: • You push and release the ON/OFF/MODE button. • You turn OFF the ignition. • You switch off ESP. To Resume Speed Push the lever upward (RESUME/ACCEL) and release.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 WARNING! The Resume function should only be used if traffic and road conditions permit. Resuming a set speed that is too high or too low for prevailing traffic and road conditions could cause the vehicle to accelerate or decelerate too sharply for safe operation. This could cause an accident and/or serious injury. To Vary the Speed Setting While ACC is set, you can increase the set speed by lifting and holding the lever up (RESUME/ACCEL).
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The ACC system maintains set speed when driving up hill and down hill. However, a slight speed change on moderate hills is normal. In addition, downshifting may occur while climbing uphill or descending downhill. This is normal operation and necessary to maintain set speed. Setting the Following Distance in ACC The specified following distance for ACC can be set by varying the distance setting between long, medium, and short.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 If there is no vehicle ahead, the vehicle will maintain the set speed. If a slower moving vehicle is detected in the same lane, the EVIC displays the “Sensed Vehicle Indicator” icon, and the system adjusts vehicle speed automatically to maintain the distance setting, regardless of the set speed. The vehicle will then maintain the set distance until: • The vehicle ahead accelerates to a speed above the set speed.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE cluster between the speedometer and the tachometer. The information it displays depends on ACC system status. Press the MENU button (located on the steering wheel) repeatedly until one of the following displays in the EVIC: Menu Button Adaptive Cruise Control (ACC) Menu The EVIC displays the current ACC system settings.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 CRUISE OFF ACC READY − When ACC is deactivated, the display will read “CRUISE OFF.” − When ACC is activated, the display will read “ACC READY.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ACC SET − When ACC is set, the set speed will display. 1 — Sensed Vehicle Indicator 2 — Set Speed 3 — Your Vehicle 4 — Following Distance Setting: Three Bars = Long; Two Bars = Medium; One Bar = Short. The set speed will continue to display in place of the odometer reading when changing the EVIC display while ACC is set.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 The ACC SET screen will display once again if any ACC activity occurs, which may include any of the following: • Set speed change • Distance setting change • System cancel • Acquisition/loss of Target • Driver override • System off • Proximity warning • ACC warning The EVIC will return to the last display selected after five seconds of no ACC activity.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Display Warnings and Maintenance ACC Blinded Warning The ACC Blinded Warning will display when conditions temporarily limit system performance. This most often occurs at times of poor visibility, such as in snow, fog, heavy rain, or when driving into direct sunlight (sunrise or sunset). The ACC system may also become temporarily blinded due to obstructions, such as dirt or ice. In these cases, the EVIC will display “ACC Blinded” and the system will deactivate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 If weather conditions are not a factor, the driver should examine the sensor. It may require cleaning or removal of an obstruction. The sensor is located behind the grille, slightly offset from the center of the grille. • Always keep the sensor clean. Carefully wipe the sensor lens with a soft cloth. Be cautious not to damage the sensor lens. • Do not remove any screws from the sensor or the sensor mount.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Installing a vehicle front-end protector or an aftermarket grille or modifying the grille is not recommended. Doing so may block the sensor and inhibit ACC operation. ACC Unavailable Warning If the system turns off, and the EVIC displays ⬙ACC UNAVAILABLE,⬙ there may be a temporary malfunction that limits ACC functionality. Although the vehicle is still drivable under normal conditions, ACC will be temporarily unavailable.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Precautions While Driving with ACC In certain driving situations, ACC may have detection issues. In these cases, ACC may brake late or unexpectedly. The driver needs to stay alert and may need to intervene. 3 Adding a Trailer Hitch The weight of a trailer hitch may affect the performance of ACC. If there is a noticeable change in performance following the installation of a hitch, such as reduced detection range, please see your authorized dealer for service.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using ACC on Hills When driving on hills, ACC may not detect a vehicle in your lane. Depending on the speed, vehicle load, traffic conditions, and the steepness of the hills, ACC performance may be limited. ACC may occasionally provide braking and/or a driver alert that you consider unnecessary. This may be the system’s response to signs, guardrails, and other stationary objects in a curve. This may also occur at the base of dramatic hills.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 Lane Changing ACC will not detect a vehicle until it is completely in the lane in which you are traveling. In the illustration shown, ACC has not yet detected the vehicle changing lanes and it will not until it may be too late to take action. ACC will not detect a vehicle until it is completely in the lane. There will not be sufficient distance to the lane-changing vehicle. Always be attentive and ready to apply the brakes if necessary.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Stationary Objects and Vehicles ACC does not react to stationary objects and stationary vehicles. For example, ACC will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane. Always be attentive and ready to apply the brakes if necessary. General Information CLASS 1 LASER PRODUCT Classification Specifications: 21 C.F.R part 1040.10 & 1040.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 Normal (Fixed Speed) Cruise Control Mode In addition to adaptive cruise control mode, a normal (fixed speed) cruise control mode is available for cruising at fixed speeds. The Normal cruise control mode is designed to maintain a set cruising speed without requiring the driver to operate the accelerator. Cruise control can only be operated if the vehicle speed is above 25 mph (40 km/h).
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Vary the Speed Setting There are two ways to change the set speed: • The Electronic Stability Program/Traction Control System (ESP/TCS) activates. • Use the accelerator pedal to adjust the vehicle to the desired speed and push the lever down (“SET/ DECEL”). To Resume Push the lever up and release (“RESUME/ACCEL”) and then remove your foot from the accelerator pedal. The EVIC will display the last set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 REAR PARK ASSIST The Rear Park Assist is a driver aid that senses for obstacles behind the vehicle. Refer to the Warnings, Cautions, and Notes in this section for system limitations and usage recommendations. The system uses four sensors located in the rear bumper to scan for obstacles up to 79 in (200 cm) away from the rear bumper fascia.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The warning display contains two sets of yellow and red indicators, one set to warn of obstacles behind the left rear of the vehicle and the other set to warn of obstacles behind the right rear of the vehicle. The driver can view the indicators either through the rearview mirror or by looking at the display above the rear window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 NOTE: The Rear Park Assist will MUTE the radio, if on, when the system is sounding an audio tone. WARNING! • Drivers must be careful when backing up even when using the Rear Park Assist. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • The Rear Park Assist is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using the Rear Park Assist to be able to stop in time when the obstacle is detected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 These lights also turn on when a door is opened, or when the UNLOCK button on the Remote Keyless Entry (RKE) transmitter is pressed, or when the dimmer control is turned fully upward, past the second detent. Sunglasses Storage At the rear of the console, a compartment is provided for the storage of a pair of sunglasses. The storage compartment access is a ⬙push/push⬙ design. Push on the raised bar on the compartment door to open.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink威 buttons are located in the overhead console, and contain one, two, or three dots/lines designating the different HomeLink威 channels. HomeLink威 Buttons NOTE: HomeLink威 is disabled when the Vehicle Security Alarm is active. WARNING! • Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 Programming HomeLink姞 Before You Begin If you have not trained any of the HomeLink威 buttons, erase all channels before you begin training. To do this, press and hold the two outside buttons for up to 20 seconds. The EVIC will display “CLEARING CHANNELS.” Release the buttons when the EVIC message states “CHANNELS CLEARED.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section. 4. Press and hold the just-trained HomeLink威 button. If the channel has been trained, the EVIC display will now state “CHANNEL # TRANSMIT.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 6. Firmly press and release the “learn” or “training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7. Return to the vehicle and press the programmed HomeLink威 button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE has successfully accepted the frequency signal. The EVIC display will change from “CHANNEL # TRAINING” to “CHANNEL # TRAINED.” If you unplugged the device for training, plug it back in at this time. Then proceed with Step 4 under “Programming HomeLink威” earlier in this section. Using HomeLink姞 To operate, simply press and release the programmed HomeLink威 button. Activation will now occur for the trained device (i.e.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Troubleshooting Tips If you are having trouble programming HomeLink威, here are some of the most common solutions: 2. This device must accept any interference that may be received including interference that may cause undesired operation • Replace the battery in the original transmitter. NOTE: The transmitter has been tested and it complies with FCC and IC rules.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. Power Sunroof Controls WARNING! • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 Opening Sunroof — Express Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully and then stop automatically. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Closing Sunroof — Express Press the switch forward and release, and the sunroof will close automatically from any position.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. Sunroof Maintenance Use only a nonabrasive cleaner and a soft cloth to clean the glass panel. NOTE: The sunshade cannot be closed if the sunroof is open.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed. ELECTRICAL POWER OUTLETS There are two 12-Volt electrical outlets on this vehicle. Both of the outlets are protected by a fuse. NOTE: If desired, the power outlet next to the ash receiver tray (if equipped) can be converted by your authorized dealer to provide power with the ignition switch in the LOCK position.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The center console outlet is powered directly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or prevent engine starting. Center Console Power Outlet WARNING! To avoid serious injury or death: • Do not use a three-prong adapter. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 CAUTION! CAUTION! (Continued) • Many accessories that can be plugged in draw power from the vehicle’s battery even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS Front Seat Cupholders The cupholders are located in the forward edge of the center console. Rear Seat Cupholders The rear seat cupholders are located in the center armrest between the rear seats. The cupholders are positioned forward in the armrest and side-by-side to provide convenient access to beverage cans or bottles while maintaining a resting place for the rear occupants elbows.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 STORAGE Console Features The center console contains two shift bezel cubby bins with rubber mats for holding small items. For vehicles not equipped with navigation radio, the console also contains an extra storage bin located below the climate control, which holds up to four CD jewel cases. 3 Without Vehicle Entertainment System (VES威) Two separate storage compartments are also located underneath the armrest.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The top compartment holds small items, such as a pen and note pad, while the larger bottom compartment will hold CDs and alike. The bottom compartment also contains a 12-Volt power outlet and a molded-in coin holder (designed to hold various size coins). A slot in the left and right side of the top compartment provides clearance for power cords to pass conveniently out of the bin with the lid closed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 WARNING! (Continued) WARNING! • Always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible. • Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. • Do not pile luggage or cargo higher than the top of the seatback.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • To help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. turn on the rear window defroster and the heated outside rearview mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 LOAD LEVELING SYSTEM — IF EQUIPPED The automatic load leveling system will provide a levelriding vehicle under most passenger and cargo loading conditions. A hydraulic pump contained within the shock absorbers raises the rear of the vehicle to the correct height. It takes approximately 1 mile (1.6 km) of driving for the leveling to complete depending on road surface conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 205 䡵 Instrument Cluster — Base . . . . . . . . . . . . . . . 206 䡵 Instrument Cluster — Premium . . . . . . . . . . . 207 䡵 Instrument Cluster Descriptions . . . . . . . . . . . 208 䡵 Electronic Vehicle Information Center (EVIC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 220 ▫ Electronic Vehicle Information Center (EVIC) Displays . . . . . . . . . . . . . . . . . . . . . . . . . . .
202 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Sales Code REQ — AM/FM Stereo Radio And 6–Disc CD/DVD Changer (MP3/WMA AUX Jack) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238 ▫ Operating Instructions - Radio Mode . . . . . . 238 ▫ Operation Instructions - (Disc Mode For CD And MP3/WMA Audio Play, DVD-Video) . . . 246 ▫ Notes On Playing MP3/WMA Files . . . . . . . 248 ▫ List Button (Disc Mode For MP3/WMA Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 203 ▫ Operation Instructions — CD Mode For CD And MP3 Audio Play . . . . . . . . . . . . . . . . . 270 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . 273 ▫ List Button (CD Mode For MP3 Play) . . . . . . 275 ▫ Info Button (CD Mode For MP3 Play) . . . . . . 275 䡵 Universal Consumer Interface (UCI) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276 ▫ Connecting The iPod威 . . . . . . . . . . . . . . . . . 277 ▫ Using This Feature . . . . . . . .
204 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operating Instructions — Video Entertainment System (VES)™ (If Equipped) . . . . . . . . . . . . . . . . . . . . . . . 286 䡵 Kicker威 High Performance Sound System With Driver-Selectable Surround (DSS) – If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 287 䡵 CD/DVD Maintenance . . . . . . . . . . . . . . . . . 292 䡵 Radio Operation And Cellular Phones . . . . . . . 293 䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 205 INSTRUMENT PANEL FEATURES 4 1 - Air Outlet 2 - Instrument Cluster 3 - Hazard Switch 4 - Analog Clock 5 - Electronic Stability Program Off Button* / Traction Control System Off Button* 6 - Glove Compartment 7 - Radio 8 - Climate Control 9 - Heated Seat Switch* 10 - Power Outlet 11 - Ash Tray* 12 - Storage Compartment* 13 - Ignition Switch 14 - Hood Release 15 - Trunk Release Switch 16 - Headlight Switch * If Equipped
206 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — BASE
UNDERSTANDING YOUR INSTRUMENT PANEL 207 INSTRUMENT CLUSTER — PREMIUM 4
208 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Electronic Speed Control / Adaptive Cruise Control (ACC) Indicator Light — If Equipped This light will turn on when the electronic speed control or Adaptive Cruise Control (ACC) is ON. 2. Low Fuel Indicator Light This light will turn on and a single chime will sound when the fuel level drops to 1/8 tank. 3. Front Fog Light Indicator — If Equipped This light will turn on when the front fog lights are ON. 4.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 reading is changed because of repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined. and service is required. Refer to “Electronic Vehicle Information Center (EVIC)” in this section for more information.
210 UNDERSTANDING YOUR INSTRUMENT PANEL reset the oil change indicator system (after performing the scheduled maintenance) perform the following procedure: Lo tirE When the appropriate condition exists the odometer display will toggle between Lo and tirE for three cycles. 1. Turn the ignition switch to the ON position. (Do not start the engine).
UNDERSTANDING YOUR INSTRUMENT PANEL 211 7. Tachometer The red segments indicate the maximum permissible engine revolutions per minute (RPM x 1000) for each gear range. Ease up on the accelerator before reaching the red area. 9. Anti-Lock Brake (ABS) Light — If Equipped This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. 8.
212 UNDERSTANDING YOUR INSTRUMENT PANEL 10. Electronic Stability Program (ESP) / Brake Assist System (BAS) Malfunction Indicator Light The yellow Electronic Stability Program (ESP) / Brake Assist System (BAS) Malfunction Indicator Light will turn on when the key in the ignition switch is turned to the ON position. The light should go out with the engine running. The system will turn this light on continuously while the engine is running if it detects a malfunction in either the ESP, the BAS or both. 11.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected.
214 UNDERSTANDING YOUR INSTRUMENT PANEL The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 13. Electronic Stability Program (ESP) / Traction Control System (TCS) Indicator Light — If Equipped If this indicator light flashes during acceleration, ease up on the accelerator and apply as little throttle as possible.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, refer to Section 7 and follow the warnings under the Cooling System Pressure Cap paragraph. 15. Trip Odometer Button Trip Odometer Button — Base Cluster The word ⬙TRIP⬙ will appear when this button is pressed.
216 UNDERSTANDING YOUR INSTRUMENT PANEL 18. Seat Belt Reminder Light This light will turn on for five to eight seconds as a bulb check when the ignition switch is first turned ON. A chime will sound if the driver’s seat belt is unbuckled during the bulb check. The Seat Belt Reminder Light will flash or remain on continuously if the driver’s seat belt remains unbuckled after the bulb check or when driving. 19.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 Also, have the system checked by an authorized dealer if the light does not come on during starting. 22. Tire Pressure Monitoring Telltale Light Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.
218 UNDERSTANDING YOUR INSTRUMENT PANEL When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system. Obtain SERVICE IMMEDIATELY. See an authorized dealer. 24. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system called OBD. The OBD system monitors engine and automatic transmission control systems.
220 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the instrument cluster. This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 • Surround Sound Modes (If Equipped with DriverSelectable Surround [DSS]) The system allows the driver to select information by pressing the following buttons mounted on the steering wheel. Press and release the MENU button and the mode displayed will change between Trip Functions, uconnect威 gps (if equipped), System MENU Status, and Personal Settings. Button Press the FUNCTION SELECT button to accept a selection.
222 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Vehicle Information Center (EVIC) Displays When the appropriate conditions exist, the EVIC displays the following messages: • Turn Signal On (with a continuous warning chime if the vehicle is driven more than 1 mile [1.
UNDERSTANDING YOUR INSTRUMENT PANEL 223 • SERVICE AWD SYSTEM — All Wheel Drive (AWD) system is not functioning properly and service is required. • ACC Cancelled — To disable the ACC system. Refer to “Adaptive Cruise Control (ACC)” in Section 3 (if equipped). • Normal Cruise Ready — When Adaptive Cruise Control (ACC) system is turned off and Normal (Fixed Speed) Cruise Control mode is available. Refer to “Adaptive Cruise Control (ACC)” in Section 3 (if equipped).
224 UNDERSTANDING YOUR INSTRUMENT PANEL • Attention — If the ACC system predicts that its maximum braking level is not sufficient to maintain the set distance, this message will flash and a chime will sound while ACC continues to apply its maximum braking capacity. When this occurs, you should immediately apply the brakes as needed to maintain a safe distance from the vehicle ahead. Refer to “Adaptive Cruise Control (ACC)” in Section 3 (if equipped).
UNDERSTANDING YOUR INSTRUMENT PANEL 225 • Did Not Train • Check Gascap (refer to “Adding Fuel” in Section 5) • Left Front Low Pressure (with a single chime). Refer to information on “Tire Pressure” and “Tire Pressure Monitor” under “Starting And Operating.” • Service Park Assist System (with a single chime) • Left Rear Low Pressure (with a single chime). Refer to information on “Tire Pressure” and “Tire Pressure Monitor” under “Starting And Operating.” • Right Front Low Pressure (with a single chime).
226 UNDERSTANDING YOUR INSTRUMENT PANEL MENU button. To reset the oil change indicator system (after performing the scheduled maintenance) perform the following procedure: 1. Turn the ignition switch to the ON position (Do not start the engine). • Trip A • Trip B • Elapsed Time • Display Units of Measure in 2. Fully depress the accelerator pedal slowly three times within 10 seconds. Press the SCROLL button to cycle through all the Trip Computer functions. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 • Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. DTE cannot be reset through the FUNCTION SELECT button.
228 UNDERSTANDING YOUR INSTRUMENT PANEL To Reset The Display Reset will only occur while a resettable function is being displayed. Press and release the FUNCTION SELECT button once to clear the resettable function being displayed. To reset all resettable functions, press and release the FUNCTION SELECT button a second time within three seconds of resetting the currently-displayed function. (Reset ALL will display during this three-second window).
UNDERSTANDING YOUR INSTRUMENT PANEL 229 Compass Display The compass readings indicate the direction the vehicle is facing. Press and release the COMPASS button to display one of eight comCOM- pass readings and the outside temperature. PASS Button All Wheel Drive (AWD) to Rear Wheel Drive (RWD) Refer to “All Wheel Drive — If Equipped” in Section 5 for more information on the All Wheel Drive (AWD) system.
230 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Compass Calibration If the compass appears erratic and the “CAL” message does not appear in the EVIC display, you must put the compass into the Calibration Mode manually as follows: 1. Turn the ignition switch ON. 2. Press and hold the COMPASS button for approximately two seconds. 3. Press the SCROLL button until “Calibrate Compass” displays in the EVIC. 4. Press and release the FUNCTION SELECT button to start the calibration.
UNDERSTANDING YOUR INSTRUMENT PANEL 231 3. Press the SCROLL button until “Compass Variance” message and the last variance zone number displays in the EVIC. 4. Press and release FUNCTION SELECT button until the proper variance zone is selected according to the map. 5. Press and release the COMPASS button to exit. Compass Variance Map 1. Turn the ignition switch ON. 2. Press and hold the COMPASS button for approximately two seconds.
232 UNDERSTANDING YOUR INSTRUMENT PANEL uconnect姞 gps (Navigation) — If Equipped uconnect威 gps (Navigation) Display Control Press and release the MENU button until Navigation displays in the EVIC. When the Navigation System is On, the steering wheel buttons can be used to select the Map or Menu display on the Navigation Unit.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 the FUNCTION SELECT button while in this display to select English, Espanol, Deutsch, Italiano, or Francais. Then, as you continue, the information will display in the selected language. NOTE: The EVIC will not change the uconnect威 language selection. Refer to “Language Selection” under “uconnect威 phone” in Section 3.
234 UNDERSTANDING YOUR INSTRUMENT PANEL When OFF is selected, only the MEMORY switch on the driver’s door trim panel will recall memory profiles. To make your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears. Refer to “Driver Memory Seat” in Section 3. “Sound Horn with Remote Key Lock” When ON is selected, a short horn sound will occur when the RKE LOCK button is pressed. This feature may be selected with or without the flash lights on lock/unlock feature.
UNDERSTANDING YOUR INSTRUMENT PANEL 235 your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears. “Headlights On with Wipers” (Available with Auto Headlights Only) When ON is selected, and the HEADLIGHT switch is in the AUTO position, the headlights will turn on approximately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on by this feature.
236 UNDERSTANDING YOUR INSTRUMENT PANEL “Delay Power Off to Accessories Until Exit” When this feature is selected, the power WINDOW switches, radio, uconnect威 phone (if equipped), DVD video system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 60 minutes after the ignition switch is turned OFF. Opening a vehicle door will cancel this feature. To make your selection, press and release the FUNCTION SELECT button until “Off,” “45 sec.,” “5 min.,” “10 min.,” “30 min.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 “Turn-by-Turn Navigation” — If Equipped When ON is selected, the turn-by-turn directions will appear in the display as the vehicle approaches a designated turn within a programmed route. To make your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears. SETTING THE ANALOG CLOCK To set the analog clock at the top center of the instrument panel, press and hold the button until the setting is correct.
238 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second time to turn off the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. SCAN Button Pressing the SCAN button causes the tuner to search for the next listenable station in AM, FM or Satellite (if equipped) frequencies, pausing for five seconds at each listenable station before continuing to the next.
240 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save the time change. TUNE Control Turn the rotary TUNE/SCROLL control knob clockwise to increase or counterclockwise to decrease the frequency. 5. To exit, press any button/knob or wait five seconds. Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 SCROLL control knob to the right or left to adjust the sound level from the right or left side speakers. Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary TUNE/SCROLL control knob again to exit setting tone, balance, and fade.
242 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 16-Digit Character Display R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R & B Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 • DISC Play/Pause - You can toggle between playing the DVD and pausing the DVD by pushing the SELECT button (if equipped). • DVD Play Options - Selecting the DVD Play Options will display the following: • Subtitle – Repeatedly pressing SELECT will switch subtitles to different subtitle languages that are available on the disc (if equipped). • Audio Stream – Repeatedly pressing SELECT will switch to different audio languages (if supported on the disc) (if equipped).
244 UNDERSTANDING YOUR INSTRUMENT PANEL TUNE/SCROLL control knob to adjust the minutes. Press the TUNE/SCROLL control knob again to save changes. down and selecting ⬙other.⬙ Enter the country code using the TUNE/SCROLL control knob to scroll up and down to select the number and then push to select. • Player Defaults - Selecting this item will allow the user to scroll through the following items and set defaults according to customer preference.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 Aspect Ratio — If Equipped Selecting this item allows you to choose between wide screen, pan scan, and letter box. AutoPlay — If Equipped When this is set to On and a DVD video is inserted, it will bypass the DVD menu screen and automatically play the movie. In some rare cases, the DVD player may not auto-play the main title. In such cases, use the MENU button on the remote control to select desired title to play.
246 UNDERSTANDING YOUR INSTRUMENT PANEL Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 These buttons tune the radio to the stations that you commit to pushbutton memory {12 AM, 12 FM, and 12 Satellite (if equipped) stations}. DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 Radio display will show ⬙LOADING DISC⬙ when the disc is loading and “READING DISC” when the radio is reading the disc. CAUTION! This CD player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. Eject Button — Ejecting Compact Disc(s) Press the EJECT button and the pushbutton with the corresponding number (1-6) where the CD was loaded and the disc will unload and move to the entrance for easy removal.
248 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF (CD MODE) Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released, or RW or another CD button is pressed. The RW (Rewind) button works in a similar manner. AM or FM Button (CD MODE) Switches the radio into the AM or FM radio mode. Notes On Playing MP3/WMA Files The radio can play MP3/WMA files; however, acceptable MP3/WMA file recording media and formats are limited.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3/ WMA files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3/ WMA playback may result in longer disc loading times. frequencies in the following table are supported.
250 UNDERSTANDING YOUR INSTRUMENT PANEL ID3 Tag information for artist, song title, and album title are supported for ID3 version 1 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported. Playback of MP3/WMA Files When a medium containing MP3/WMA data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3/WMA files.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 INFO Button (DISC Mode for MP3/WMA Play) Pressing the INFO button repeatedly will scroll through the following TAG information: Song Title, Artist, File Name, and Folder Name (if available). Press the INFO button once more to return to ⬙elapsed time⬙ priority mode. Press and hold the INFO button for three seconds or more and radio will display song titles for each file. Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display.
252 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Press the TIME button to change the display from elapsed playing time to time of day. The time of day will display for five seconds. Operating Instructions - uconnect威 studios (Satellite Radio) (If Equipped) Refer to “uconnect威 studios (Satellite Radio)” in this section. RW/FF (Auxiliary Mode) No function.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. DTS™ ⬙DTS™⬙ and ⬙DTS™ 2.0⬙ are trademarks of Digital Theater Systems, Inc. AM/FM/CD/DVD RADIO (RER/REN) – IF EQUIPPED NOTE: The sales code is located on the lower right side of the unit’s faceplate. The REN and RER radios contain a CD/DVD player, USB port, and a 30-gigabyte hard drive (HDD).
254 UNDERSTANDING YOUR INSTRUMENT PANEL To Manually Set the Clock — RER/REN 1. Turn on the radio. 2. Touch the screen where the time is displayed. 3. Touch the screen where “User Clock” is displayed. The clock setting menu will appear on the screen. 4. To move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is displayed. To move the hour backward, touch the screen where the word “Hour” with the arrow pointing downward is displayed. 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 Show Time if Radio is Off When selected, this feature will display the time of day on the touch screen when the radio is turned off. Proceed as follows to change the current setting: 1. Turn on the radio. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “Show Time if Radio is Off.
256 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RES — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. TIME Button Press the TIME button to alternate locations of the time and frequency display. Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the right side TUNE/ SCROLL control knob. 3.
258 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the mid-range tones. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones. Push the rotary TUNE/SCROLL control knob a fourth time and BALANCE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 These buttons tune the radio to the stations that you commit to pushbutton memory (12 AM and 12 FM stations).
260 UNDERSTANDING YOUR INSTRUMENT PANEL If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. CAUTION! • This CD player will accept 4-3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels.
UNDERSTANDING YOUR INSTRUMENT PANEL 261 the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD and MP3 modes. TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display. RW/FF Press and hold the FF (Fast Forward) button and the CD player will begin to fast forward until FF is released, or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner.
262 UNDERSTANDING YOUR INSTRUMENT PANEL Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file normally. UDF and Apple HFS formats are not supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 263 Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
264 UNDERSTANDING YOUR INSTRUMENT PANEL Loading times for playback of MP3 files may be affected by the following: • Media - CD-RW media may take longer to load than CD-R media • Medium formats - Multisession discs may take longer to load than non-multisession discs • Number of files and folders - Loading times will increase with more files and folders To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs.
UNDERSTANDING YOUR INSTRUMENT PANEL 265 SALES CODE RES/RSC — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) AND SIRIUS RADIO NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
266 UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. Voice Recognition System (Radio) — If Equipped Refer to “Voice Recognition System (VR)” in Section 3. Voice Recognition Button uconnect威 phone — If Equipped Press this button to operate the uconnect威 phone feature (if equipped).
UNDERSTANDING YOUR INSTRUMENT PANEL 267 5. To exit, press any button/knob or wait five seconds. The clock can also be set by pressing the SETUP button. For vehicles equipped with satellite radio, press the SETUP button, use the TUNE/SCROLL control to select SET CLOCK, and then follow the above procedure, starting at Step 2. For vehicles not equipped with satellite radio, press the SETUP button and then follow the above procedure, starting at Step 2.
268 UNDERSTANDING YOUR INSTRUMENT PANEL SCROLL control knob to the right or left to adjust the sound level from the right or left side speakers. Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary TUNE/SCROLL control knob again to exit setting tone, balance, and fade.
UNDERSTANDING YOUR INSTRUMENT PANEL 269 Program Type Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 16-Digit Character Display R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R&B Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode.
270 UNDERSTANDING YOUR INSTRUMENT PANEL SET/RND Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND button. The symbol SET 1 will now show in the display window. Select the button (1 to 6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the SET/RND button, the station will continue to play but will not be stored into pushbutton memory.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 • This radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable compact discs (CD-RW), compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks. Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD player and the CD icon will illuminate on the radio display. If a CD does not go into the slot more than 1.0 in (2.
272 UNDERSTANDING YOUR INSTRUMENT PANEL If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the CD is not removed, the radio will reinsert the CD but will not play it. A disc can be ejected with the radio and ignition OFF. NOTE: Ejecting with the ignition OFF is not allowed on convertible or soft-top models (if equipped). SEEK Button Press the right SEEK button for the next selection on the CD.
UNDERSTANDING YOUR INSTRUMENT PANEL 273 Notes On Playing MP3 Files The radio can play MP3 files; however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions. Supported Media (Disc Types) The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension.
274 UNDERSTANDING YOUR INSTRUMENT PANEL Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file.
UNDERSTANDING YOUR INSTRUMENT PANEL 275 Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
276 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack which allows the user to plug in a portable device such as an MP3 player or cassette player and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the AUX button will change the mode to auxiliary device if the AUX jack is connected.
UNDERSTANDING YOUR INSTRUMENT PANEL 277 feature, refer to the separate RER, REN or REZ User’s Manual. UCI is available only if equipped as an option with these radios. • Connecting an iPod威 to the AUX port located in the radio faceplate, plays media, but does not use the UCI feature to control the connected device. This feature allows you to plug an iPod威 into the vehicle’s sound system through a 16–pin connector using the provided interface cable.
278 UNDERSTANDING YOUR INSTRUMENT PANEL • If the iPod威 battery is completely discharged, it may not communicate with the UCI system until a minimum charge is attained. Leaving the iPod威 connected to the UCI system may charge it to the required level. Using This Feature By using the optional connection cable to connect an iPod威 to the vehicle’s UCI 16–pin connector port: • The iPod威 audio can be played on the vehicle’s sound system, providing metadata (Artist, track title, album, etc.
UNDERSTANDING YOUR INSTRUMENT PANEL 279 • Jump backward in the current track by pressing and holding the << RW button. Holding the << RW button long enough will take you to the beginning of the current track. • Jump forward in the current track by pressing and holding the FF >> button. • A single press backward << RW or forward FF >> will jump backward or forward respectively, for five seconds. • Use the << SEEK and SEEK >> buttons to jump to the previous or next track.
280 UNDERSTANDING YOUR INSTRUMENT PANEL Shuffle OFF modes for the iPod威. If the RND icon is showing on the radio display, then the shuffle mode is ON. List Or Browse Mode During Play mode, pressing any of the buttons described below, takes you to List mode. List mode enables you to scroll through the list of menus and tracks on the iPod威. • TUNE control knob: The TUNE control knob functions in a similar manner as the scroll wheel on the iPod威.
UNDERSTANDING YOUR INSTRUMENT PANEL 281 • To Exit List mode without selecting a track, press the same PRESET button again to go back to Play mode. • LIST button: The LIST button will display the top level menu of the iPod威. Turn the TUNE control knob to list the top-menu item you wish to select and press the TUNE control knob. This will display the next sub-menu list item on the iPod威 then you can follow the same steps to go to the desired track in that list.
282 UNDERSTANDING YOUR INSTRUMENT PANEL uconnect姞 studios (SATELLITE RADIO) — IF EQUIPPED (REN/REQ/RER/RES/REU RADIOS ONLY) Satellite radio uses direct satellite-to-receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius Satellite Radio. This service offers over 130 channels of music, sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios.
UNDERSTANDING YOUR INSTRUMENT PANEL 283 selected. Press the TUNE/SCROLL control knob and the Sirius ID number will display. The Sirius ID number display will time out in two minutes. Press any button on the radio to exit this screen. Selecting uconnect姞 studios (Satellite) Mode Press the SAT button until ⬙SAT⬙ appears in the display. A CD may remain in the radio while in the Satellite radio mode. ESN/SID Access With REN/RER Radios While in SAT mode, press the MENU button on the radio faceplate.
284 UNDERSTANDING YOUR INSTRUMENT PANEL • Dense tree coverage may interrupt reception in the form of short audio mutes. • Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage. Operating Instructions — uconnect姞 studios (Satellite) Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 285 RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next channel in the direction of the arrows. TUNE Control (Rotary) Turn the rotary TUNE/SCROLL control knob clockwise to increase or counterclockwise to decrease the channel. MUSIC TYPE Button — Except REU Radio Pressing this button once will turn on the Music Type mode for five seconds.
286 UNDERSTANDING YOUR INSTRUMENT PANEL • Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number. This number is used to activate, deactivate, or change the Sirius subscription. SET Button – To Set the Pushbutton Memory When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button.
UNDERSTANDING YOUR INSTRUMENT PANEL 287 KICKER姞 HIGH PERFORMANCE SOUND SYSTEM WITH DRIVER-SELECTABLE SURROUND (DSS) – IF EQUIPPED any stereo audio source. A new feature of the Kicker威 audio system offers the ability to choose surround sound for any audio source. “Audio Surround” is optimized for front seat passengers for any audio source.
288 UNDERSTANDING YOUR INSTRUMENT PANEL When in “Audio Surround” mode, balance is set automatically. Fader control is available to add more surround audio if desired. Refer to your Video Entertainment System (VES)™, RER Navigation or REN Multimedia User Manuals for detailed operating instructions. uconnect studios姞 (SIRIUS BACKSEAT TV™) — IF EQUIPPED Satellite video uses direct satellite receiver broadcasting technology to provide streaming video.
UNDERSTANDING YOUR INSTRUMENT PANEL 289 4 Opening the Rear Seat VES™ VES™ Video Screen • The LCD screen swings up from the rear of the armrest to allow the rear seat passenger(s) to view the display. NOTE: Close the armrest after the LCD screen has been raised to its viewing position. • The radio and DVD player controls allow front seat operation for easy setup in the case of younger rear seat passengers.
290 UNDERSTANDING YOUR INSTRUMENT PANEL • A battery-powered infrared remote control snaps into a molded compartment in the center console armrest upper storage bin. Audio/Video RCA Jacks (AUX Jacks) on the rear of the center console enable the monitor to display video directly from a video camera, connect video games for display on the screen, or play music directly from an MP3 player. 1. Video in (yellow) 2. Left audio in (white) 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 291 REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the surface of the steering wheel at the three and nine o’clock positions. The remote sound system controls are located on the surface of the steering wheel at the three and nine o’clock positions. Vehicles equipped with steering wheel-mounted buttons are also equipped with the Electronic Vehicle Information Center (EVIC).
292 UNDERSTANDING YOUR INSTRUMENT PANEL Press the AUDIO MODE button to select the Compass/Temp/Audio screen. This screen displays radio and media mode information AUDIO depending on which radio is in the vehicle. MODE Button If the Compass/Temp/Audio screen is already displayed when the AUDIO MODE button is pressed, then the mode will change (i.e. from AM to FM, to Media mode, etc., depending on which radio is in the vehicle).
UNDERSTANDING YOUR INSTRUMENT PANEL 293 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. NOTE: If you experience difficulty in playing a particular disc, it may be damaged (i.e. scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service.
294 UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS The air conditioning and heating system is designed to make you comfortable in all types of weather. Manual Air Conditioning and Heating System Blower Control The rotary knob on the left controls the blower. The control has an OFF position and four speed settings. The blower will remain on until the control is turned to the OFF position or the ignition is turned OFF.
UNDERSTANDING YOUR INSTRUMENT PANEL 295 Temperature Control The rotary knob in the center controls air temperature. Rotate the control to the left for cooler air temperature and to the right for warmer air temperature. Rotating the control to the extreme left provides the coldest setting. Rotating the control to the extreme right provides the warmest setting. Mode Control The rotary knob on the right controls airflow distribution.
296 UNDERSTANDING YOUR INSTRUMENT PANEL • Bi-Level Air flows through the outlets located in the instrument panel and through the outlets located on the floor. Air flows through the registers in the back of the center console to the rear seat passengers. These registers can be closed to partially block airflow. • Panel Air flows through the outlets located in the instrument panel. Air flows through the registers in the back of the center console to the rear seat passengers.
UNDERSTANDING YOUR INSTRUMENT PANEL 297 Automatic Temperature Control — If Equipped Automatic Temperature Controls Automatic Operation The Dual-Zone Climate Control System automatically maintains the climate in the cabin of the vehicle at the comfort levels desired by the driver and passenger. Operation of the system is quite simple. Begin by turning the mode control knob (on the right) to AUTO, and place the blower control knob (on the left) to either LO AUTO or HI AUTO.
298 UNDERSTANDING YOUR INSTRUMENT PANEL 72°F (22°C) is the recommended setting for maximum comfort for the average person; however, this may vary. NOTE: The temperature setting can be adjusted at any time without affecting automatic operation. Air conditioning in this system is automatic. Pressing the air conditioning control button while in AUTO mode will cause the indicator in the control button to flash three times and then turn off.
UNDERSTANDING YOUR INSTRUMENT PANEL 299 Manual Operation This system offers a full complement of manual override features, which consist of blower preferred automatic, mode preferred automatic, or blower and mode preferred automatic. This means the operator can override the blower, the mode, or both. There is a manual blower range for times when the AUTO setting is not desired. The blower can be set to any fixed blower speed by rotating the blower control knob (on the left).
300 UNDERSTANDING YOUR INSTRUMENT PANEL
UNDERSTANDING YOUR INSTRUMENT PANEL 301 The operator can override the AUTO mode setting to change airflow distribution by rotating the mode control knob (on the right) to one of the following positions. • Defrost Air is directed to the windshield through the outlets at the base of the windshield. Air is also directed to the front door windows through the side window demister grilles. • Defrost/Floor Air flows through the front and rear floor outlets and the outlets at the base of the windshield.
302 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: To control the air conditioning manually, the mode selector must be moved out of the AUTO position. • Recirculation Control This button can be used to block out smoke, odors, dust, high humidity, or if rapid cooling is desired. The Recirculation mode should only be used temporarily. An indicator in the button illuminates when the Recirculation mode is active. You may use this feature separately. NOTE: Extended use of recirculation may cause the windows to fog.
UNDERSTANDING YOUR INSTRUMENT PANEL 303 Winter Operation Use of the air Recirculation mode during Winter months is not recommended because it may cause window fogging. Vacation Storage Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.
304 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions for Various Weather Conditions
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 309 ▫ General Information . . . . . . . . . . . . . . . . . . 313 ▫ Automatic Transmission . . . . . . . . . . . . . . . 309 ▫ Brake/Transmission Shift Interlock System . . 315 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 310 ▫ Brake/Transmission Interlock Manual Override . . . . . . . . . . . . . . . . . . . . . . . . . . 315 ▫ Extremely Cold Weather (Below -20°F Or -29°C) . . . . . . . . . .
306 STARTING AND OPERATING 䡵 Driving On Slippery Surfaces . . . . . . . . . . . . . 327 ▫ Brake Assist System (BAS) . . . . . . . . . . . . . . 337 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . 327 ▫ Electronic Stability Program (ESP) . . . . . . . . 338 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . 328 ▫ Synchronizing ESP . . . . . . . . . . . . . . . . . . . 340 䡵 Driving Through Water . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 307 ▫ Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . 353 ▫ Premium System — If Equipped . . . . . . . . . 366 ▫ Compact Spare Tire — If Equipped . . . . . . . 353 ▫ General Information . . . . . . . . . . . . . . . . . . 370 ▫ Limited-Use Spare — If Equipped . . . . . . . . 354 䡵 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . 370 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . 355 ▫ 2.7L Engine . . . . . . . . . . . . . . . . . . . . . .
308 STARTING AND OPERATING 䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 375 ▫ Common Towing Definitions . . . . . . . . . . . . 380 ▫ Fuel Filler Cap (Gas Cap) . . . . . . . . . . . . . . 375 ▫ Trailer Hitch Classification . . . . . . . . . . . . . . 383 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . 377 ▫ Trailer Towing Weights (Maximum Trailer Weight Ratings) . . . . . . . . . . . . . . . . . . . . . 384 䡵 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 309 STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition.
310 STARTING AND OPERATING CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly on the brake pedal.
STARTING AND OPERATING 311 Extremely Cold Weather (Below -20°F or -29°C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your authorized dealer) is recommended. If Engine Fails To Start WARNING! • Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury.
312 STARTING AND OPERATING release it as soon as the starter engages. The starter motor will disengage automatically in 10 seconds. Once this occurs, release the accelerator pedal, turn the ignition switch to the LOCK position, wait 10 to 15 seconds, then repeat the normal starting procedure. The engine block heater cord is routed under the hood on the driver side of the vehicle. It has a removable cap that is located on the driver side of the Integrated Power Module.
STARTING AND OPERATING 313 CAUTION! (Continued) WARNING! • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly on the brake pedal. It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed.
314 STARTING AND OPERATING • Shift lever position • Accelerator position • Vehicle speed The gear shifting process is continuously adapted, dependent on the driving style, the driving situation, and the road characteristics. NOTE: • After selecting any driving position, wait a moment to allow the gear to engage fully before accelerating, especially when the engine is cold. • If there is a need to restart the engine, be sure to cycle the key to the LOCK position before restarting.
STARTING AND OPERATING 315 WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the transmission into PARK, remove the key from the ignition, and apply the parking brake. Once the key is removed from the ignition, the transmission shift lever is locked in the PARK position, securing the vehicle against unwanted movement.
316 STARTING AND OPERATING located to the right of the shift lever. The override access port is at the top of the bin to the right of the shift lever gate. small flat blade screwdriver or alike. While pressing the override, move the shift lever out of the PARK position. When complete, return the rubber tray to its original position. 4-Speed Automatic Transmission NOTE: Under extreme cold temperatures (-6°F (-21°C) and when in DRIVE, transmission operation may be briefly limited to only 2nd gear operation.
STARTING AND OPERATING 317 When parking on a flat surface, place the shift lever in the PARK position first, and then apply the parking brake. When parking on a hill, it is important to set the parking brake before placing the shift lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of park. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.
318 STARTING AND OPERATING The following indicators should be used to ensure that you have engaged the shift lever in the PARK position: NEUTRAL The engine may be started in this range. • When shifting into PARK move the shift lever all the way forward and left until it stops and is fully seated. CAUTION! • Look at the shift indicator display on the instrument panel to ensure it is in the P position.
STARTING AND OPERATING 319 “D” (Overdrive) This range should be used for most city and highway driving. It provides the smoothest up shifts and down shifts and the best fuel economy. Select the “3” range when frequent transmission shifting occurs when using the Overdrive range, such as when operating the vehicle under heavy loading conditions (in hilly terrain, traveling into strong head winds, or while towing heavy trailers).
320 STARTING AND OPERATING occur only to prevent engine overspeed while downshifts occur earlier than in other gear range selections. CAUTION! Never race the engine with the brakes on and the vehicle in gear, and never hold the vehicle on an incline without applying the brakes. These practices can cause overheating and damage to the transmission. Torque Converter Clutch A feature designed to improve fuel economy has been added to the automatic transmission in this vehicle.
STARTING AND OPERATING 321 Transmission Limp Home Mode The transmission is monitored for abnormal conditions. If a condition is detected that could cause damage, the transmission automatically shifts into second gear. The transmission remains in second gear despite the forward gear selected. PARK, REVERSE, and NEUTRAL will continue to operate. This reset feature allows the vehicle to be driven to an authorized dealer for service without damaging the transmission.
322 STARTING AND OPERATING When parking on a flat surface, place the shift lever in the PARK position first, and then apply the parking brake. When parking on a hill, it is important to set the parking brake before placing the shift lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of PARK. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.
STARTING AND OPERATING 323 The following indicators should be used to ensure that you have engaged the shift lever in the PARK position: • When shifting into PARK, move the shift lever all the way forward and left until it stops and is fully seated. • Look at the shift indicator display on the instrument panel to ensure it is in the P position. CAUTION! Damage to the shifter could result if the shift lever is moved out of PARK before the ignition is turned from the LOCK to ON position.
324 STARTING AND OPERATING WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have an accident. DRIVE This range should be used for most city and highway driving. It provides the smoothest upshifts and downshifts and the best fuel economy. The transmission automatically upshifts through 5th gear.
STARTING AND OPERATING 325 brought to a stop. After the vehicle has stopped, PARK, REVERSE, and NEUTRAL will continue to operate. Second gear will operate in the DRIVE position. The Malfunction Indicator Light (MIL) may be illuminated. A reset feature is available to allow the vehicle to be driven to an authorized dealer for service. To reset the transmission, use the following procedure: 1. Stop the vehicle. 2. Move the shift lever to the PARK position. 3. Turn OFF the engine. 4.
326 STARTING AND OPERATING AUTOSTICK姞 — IF EQUIPPED Autostick威 is a driver-interactive transmission that offers manual gear shifting to provide you with more control of the vehicle. Autostick威 allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situations.
STARTING AND OPERATING 327 vehicle automatically shifts into AWD mode. Automatic AWD operation could be activated by outside temperature, wheel slip, or other predetermined conditions (there may be a slight delay for AWD engagement after a wheel slip condition occurs). AWD can also be manually selected by moving the shift lever into the Autostick威 mode (+/-) or activating the windshield wipers for an extended period of time.
328 STARTING AND OPERATING WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the rear wheels. You could lose control of the vehicle and possibly have an accident. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet mud, loose sand, etc.). Traction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface.
STARTING AND OPERATING 329 Flowing/Rising Water WARNING! Do not drive on or cross a road or a path where water is flowing and/or rising (as in storm run-off). Flowing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehicle away swiftly. Failure to follow this warning may result in injuries that are serious or fatal to you, your passengers, and others around you.
330 STARTING AND OPERATING CAUTION! (Continued) WARNING! • Driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.e., engine oil, transmission/transaxle, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water. Do not continue to operate the vehicle if any fluid appears contaminated, as this may result in further damage.
STARTING AND OPERATING 331 POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these conditions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.
332 STARTING AND OPERATING Power Steering Fluid Check Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer. No chemical flushes should be used in any power steering system; only the approved lubricant may be used.
STARTING AND OPERATING 333 When parking on a hill, it is important to apply the parking brake before placing the shift lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of PARK. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The foot operated parking brake is positioned below the lower left corner of the instrument panel.
334 STARTING AND OPERATING WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle. • Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and an accident.
STARTING AND OPERATING 335 • The ABS motor running (it may continue to run for a short time after the stop), • The clicking sound of solenoid valves, • Brake pedal pulsations, and • A slight drop or fall away of the brake pedal at the end of the stop. These are all normal characteristics of ABS. WARNING! • The ABS contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.
336 STARTING AND OPERATING WARNING! (Continued) • The capabilities of an ABS equipped vehicle must never be exploited in a reckless or dangerous manner that could jeopardize the user’s safety or the safety of others. All vehicle wheels and tires must be the same size and type and tires must be properly inflated to produce accurate signals for the computer.
STARTING AND OPERATING 337 WARNING! The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. The ABS cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
338 STARTING AND OPERATING WARNING! The BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. The BAS cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING 339 flashes when the TCS is active. If the ESP/TCS Indicator Light begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. WARNING! The ESP cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.
340 STARTING AND OPERATING ESP on again, momentarily depress the ESP OFF switch and the “ESP/TCS Indicator Light” will turn off. ESP OFF Switch NOTE: To improve the vehicle’s traction when driving with snow chains, or when starting off in deep snow, sand, or gravel, it may be desirable to switch to the “Partial Off” mode by momentarily depressing the ESP OFF switch. Once the situation requiring “Partial Off” mode is overcome, turn the ESP on again by momentarily depressing the ESP OFF switch.
STARTING AND OPERATING 341 ESP/BAS Malfunction Indicator Light and ESP/TCS Indicator Light The Malfunction Indicator Light for the ESP is combined with the BAS indicator. The ESP/ BAS Malfunction Indicator Light and the ESP/ TCS Indicator Light in the instrument cluster both come on when the ignition switch is turned to the ON position. They should go out with the engine running.
342 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
STARTING AND OPERATING 343 Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation. Example: T145/80D18 103M. Tire Sizing Chart • High flotation tire sizing is based on U.S. design standards and it begins with the tire diameter molded into the sidewall. Example: 31x10.5 R15 LT. EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....
344 STARTING AND OPERATING EXAMPLE: 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
STARTING AND OPERATING 345 Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
346 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires.
STARTING AND OPERATING 347 axles must not be exceeded. For further information on GAWRs, vehicle loading, and trailer towing, refer to “Vehicle Loading” in this section. To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard.
348 STARTING AND OPERATING NOTE: • The following table shows examples on how to calculate total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load carry capacity of your vehicle. • For the following example, the combined weight of occupants and cargo should never exceed 865 lbs (392 kg).
STARTING AND OPERATING 349 5
350 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 351 WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement.
352 STARTING AND OPERATING once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under-inflated. CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem.
STARTING AND OPERATING 353 Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high-speed vehicle operation.
354 STARTING AND OPERATING WARNING! CAUTION! Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). Temporary use spare tires have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to follow the warnings, which apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control.
STARTING AND OPERATING 355 WARNING! WARNING! The limited-use spare tires are for emergency use only. Installation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than 50 mph (80 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited-use spare tire and wheel assembly. Replace (or repair) the original tire at the first opportunity and reinstall it on your vehicle.
356 STARTING AND OPERATING Many states have laws requiring tire replacement at this point. Life of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • Tire pressure • Distance driven WARNING! 1 — Worn Tire 2 — New Tire These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced.
STARTING AND OPERATING 357 Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manufacturer strongly recommends that you use tires equivalent to the originals in size, quality and performance when replacement is needed.
358 STARTING AND OPERATING WARNING! (Continued) • Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. SELF-SEALING TIRES — IF EQUIPPED A non-hardening viscous sealant applied to the inner liner of each tire fills punctures up to 0.19 in (5 mm) to minimize the loss of air pressure.
STARTING AND OPERATING 359 CAUTION! (Continued) CAUTION! (Continued) • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious damage. Stop the vehicle immediately if noise occurs that could indicate chain breakage. Remove the damaged parts of the chain before further use. • Install chains on the rear wheels as tightly as possible and then retighten after driving about 1⁄2 mile (0.
360 STARTING AND OPERATING SNOW TIRES Some areas of the country require the use of snow tires during the winter. Standard tires are of the all season type and satisfy this requirement as indicated by the M+S designation on the tire sidewall. If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of four. Failure to do so may adversely affect the safety and handling of your vehicle.
STARTING AND OPERATING 361 Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” section of this manual. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed. exceed the maximum inflation pressure molded into the tire sidewall. Refer to the “Tires – General Information” in this section for information on how to properly inflate the vehicle’s tires.
362 STARTING AND OPERATING update and the TPM Telltale Light will turn off once the system receives the updated tire pressures. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 30 psi (207 kPa).
STARTING AND OPERATING 363 NOTE: • The TPMS is not intended to replace normal tire care and maintenance or to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. • Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
364 STARTING AND OPERATING The matching full size spare wheel and tire assembly (if equipped) has a TPM sensor. The matching full size spare can be used in place of any of the four road tires. The TPMS will only monitor the pressure in the full size spare when it is used in place of a road tire. Otherwise, a spare with a pressure below the low-pressure limit will not cause the TPM Telltale Light to illuminate or the chime to sound.
STARTING AND OPERATING 365 3. Accumulation of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPM sensors. NOTE: Vehicles with Full Size Spare 1. The matching full size spare wheel and tire assembly has a TPM sensor that can be monitored by the TPMS. 2.
366 STARTING AND OPERATING the low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. Premium System — If Equipped The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors mounted to each wheel as part of the valve stem transmit tire pressure readings to the receiver module.
STARTING AND OPERATING 367 turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. Check TPMS Warning If a system fault is detected, the TPM Telltale Light will flash on and off for 75 seconds and then remain on solid. The system fault will also sound a chime.
368 STARTING AND OPERATING 1. Signal interference due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors. 2. Installing aftermarket window tinting that contains materials that may block radio wave signals. 3. Accumulation of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPM sensors.
STARTING AND OPERATING 369 the TPM Telltale Light will turn ON. In addition, the EVIC will display a low pressure message and a graphic showing the low tire pressure value flashing. 3. After driving the vehicle for up to 20 minutes above 15 mph (25 km/h) the TPM Telltale Light will turn OFF, as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires. NOTE: Vehicles with Compact Spare 1. The compact spare tire does not have a TPM sensor.
370 STARTING AND OPERATING vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
STARTING AND OPERATING 371 premium gasoline is not recommended, as it will not provide any benefit over regular gasoline in these engines. Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required. Poor quality gasoline can cause problems such as hard starting, stalling, and hesitations. If you experience these symptoms, try another brand of gasoline before considering service for the vehicle.
372 STARTING AND OPERATING CAUTION! DO NOT use gasolines containing Methanol or E85 Ethanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components. Problems that result from using methanol/gasoline or E85 ethanol blends are not the responsibility of the manufacturer. While MTBE is an oxygenate made from methanol, it does not have the negative effects of methanol.
STARTING AND OPERATING 373 MMT In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT. Gasoline blended with MMT reduces spark plug life and reduces emissions system performance in some vehicles. The manufacturer recommends that gasoline without MMT be used in your vehicle.
374 STARTING AND OPERATING • An out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your authorized dealer for service assistance. • The use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol.
STARTING AND OPERATING 375 • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the trunk closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle.
376 STARTING AND OPERATING CAUTION! (Continued) • A poorly fitting gas cap could let impurities into the fuel system. • A poorly fitting gas cap may cause the Malfunction Indicator Light (MIL) to turn on. • To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
STARTING AND OPERATING 377 WARNING! (Continued) • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. NOTE: • Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is tightened properly. The MIL in the instrument cluster may turn on if the gas cap is not secured properly. Make sure that the gas cap is tightened each time the vehicle is refueled.
378 STARTING AND OPERATING Vehicle Certification Label Your vehicle has a Vehicle Certification Label affixed to the rear of the driver’s door.
STARTING AND OPERATING 379 Overloading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and the front and rear GAWR. The best way to figure out the total weight of your vehicle is to weigh it when it is fully loaded and ready for operation. Weigh it on a commercial scale to ensure that it is not over the GVWR. Figure out the weight on the front and rear of the vehicle separately.
380 STARTING AND OPERATING TRAILER TOWING In this section, you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible. To maintain warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing.
STARTING AND OPERATING 381 WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. Tongue Weight (TW) The TW is the downward force exerted on the hitch ball by the trailer. In most cases, it should not be less than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle.
382 STARTING AND OPERATING Weight-Distributing Hitch A weight-distributing system works by applying leverage through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturer’s directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.
STARTING AND OPERATING 383 Trailer Hitch Classification Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package. See your authorized dealer for package content. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
384 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission Frontal Area Max. GTW (Gross Trailer Wt.) 1,000 lbs (454 kg) Max. Tongue Wt. (〫 see note) 100 lbs (45 kg) 2.7L & 3.5L Rear Wheel 22 sq ft (2.04 sq m) Drive (RWD) Automatic 3.5L All Wheel Drive 32 sq ft (2.97 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) (AWD) & 5.
STARTING AND OPERATING 385 Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents.
386 STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to the “Tire and Loading Information” placard for the maximum combined weight of occupants and cargo for your vehicle.
STARTING AND OPERATING 387 • When hauling cargo or towing a trailer, do not overload your vehicle or trailer. Overloading can cause a loss of control, poor performance, or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure, or tires. • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners.
388 STARTING AND OPERATING “Tires–General Information” in this section for information on tire pressures and for proper tire inflation procedures. − Also, check the trailer tires for proper tire inflation pressures before trailer usage. − Check for signs of tire wear or visible tire damage before towing a trailer. Refer to “Tires–General Information” in this section for information on tread wear indicators and for the proper inspection procedure.
STARTING AND OPERATING 389 CAUTION! WARNING! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes, and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident.
390 STARTING AND OPERATING Towing Requirements — Trailer Lights and Wiring Whenever you pull a trailer, regardless of the trailer size, stoplights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package may include a 4- and 7-pin wiring harness. Use a factory approved trailer harness and connector. NOTE: Do not cut or splice wiring into the vehicles wiring harness.
STARTING AND OPERATING 391 Towing Tips Before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Towing Tips — Automatic Transmission The DRIVE range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected.
392 STARTING AND OPERATING Towing Tips — Electronic Speed Control (If Equipped) − Do not use in hilly terrain or with heavy loads. − When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. − Use speed control in flat terrain and with light loads to maximize fuel efficiency. Towing Tips — Autostick威 (If Equipped) − By using the Autostick威 modes and selecting a specific gear range, frequent shifting can be avoided.
STARTING AND OPERATING 393 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Two-Wheel Drive and All-Wheel Drive Recreational towing for this vehicle is not recommended. NOTE: If the vehicle requires towing, make sure all four wheels are off the ground.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . 396 䡵 Jump-Starting Procedures . . . . . . . . . . . . . . . . 408 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 396 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 411 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 397 䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . 412 ▫ Jack Location/Spare Tire Stowage . . . . . . . . 398 ▫ Without The Ignition Key . . . . . .
396 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning flasher switch is located in the center of the instrument panel between the center air outlets. Press the switch to turn on the Hazard Warning flashers. When the Hazard Warning flasher switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off flashers.
WHAT TO DO IN EMERGENCIES 397 the fan control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads “H,” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.
398 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • The jack is designed to use as a tool for changing tires only.
WHAT TO DO IN EMERGENCIES 399 6 Spare Tire Fastener 4. Remove the spare tire. 5. Remove the fastener securing the jack. Jack Fastener WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided.
400 WHAT TO DO IN EMERGENCIES Preparations For Jacking 1. Park the vehicle on a firm level surface as far from the edge of the roadway as possible. Avoid icy or slippery areas. 2. Set the parking brake. 3. Place the shift lever into PARK. 4. Turn OFF the ignition. 5. Turn on the Hazard Warning flashers. 6. Block the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel.
WHAT TO DO IN EMERGENCIES 401 WARNING! (Continued) • Never start or run the engine with the vehicle on a jack. • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway, be extremely careful of motor traffic.
402 WHAT TO DO IN EMERGENCIES 3. Before raising the vehicle, use the lug wrench to loosen, but not remove, the lug nuts on the wheel with the flat tire. Turn the lug nuts counterclockwise one turn while the wheel is still on the ground. Center Cap Removal WARNING! To avoid possible personal injury, handle the wheel covers with care to avoid contact with the metal edges and retention teeth.
WHAT TO DO IN EMERGENCIES 403 4. Place the jack underneath the lift area that is closest to the flat tire. Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange. However, when reinstalling the road tire, follow the procedure under “Wheel Cover or Center Cap Installation” in place of the remaining steps in this procedure. 5. Raise the vehicle just enough to remove the flat tire and install the spare tire. 8.
404 WHAT TO DO IN EMERGENCIES Jack Engagement Locations
WHAT TO DO IN EMERGENCIES 405 11. Stow the jack, tools and flat tire. Make sure the base of the jack faces the rear of the vehicle before tightening down the fastener. WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Compact Spare Tire The compact spare tire is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only.
406 WHAT TO DO IN EMERGENCIES Wheel Cover or Center Cap Installation (If Equipped) NOTE: Do not attempt to install a center cap or wheel cover on the compact spare. 1. Mount the road tire on the axle. For vehicles equipped with wheel covers, perform Steps 2 and 3. For vehicles equipped with center caps, proceed to Step 4. 2. Install two lug nuts on the mounting studs, which are on each side of the stud that is in alignment with the valve stem.
WHAT TO DO IN EMERGENCIES 407 3. Align the valve notch in the wheel cover with the valve stem on the wheel. Install the cover by hand, snapping the cover over the two lug nuts. Do not use a hammer or excessive force to install the cover. 4. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle is lowered to the ground. 5.
408 WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES WARNING! (Continued) WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be hurt by the fan. • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
WHAT TO DO IN EMERGENCIES 409 NOTE: The battery is stored under an access cover in the trunk. Remote battery terminals are located in the engine compartment for jump-starting. 1. Wear eye protection and remove any metal jewelry such as watchbands or bracelets that might make an inadvertent electrical contact. 2. When boost is provided by a battery in another vehicle, park that vehicle within booster cable reach, but do not allow the vehicles to touch one another.
410 WHAT TO DO IN EMERGENCIES WARNING! Jump-Starting 1 — Engine Ground 2 — Positive Battery Post • You should not try to start your vehicle by pushing or towing. • Do not connect the cable to the negative post of the discharged battery. The resulting electrical spark could cause the battery to explode. • During cold weather when temperatures are below the freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump-starting because the battery could rupture or explode.
WHAT TO DO IN EMERGENCIES 411 the instrument cluster) remains on continuously after starting the engine of the vehicle with the discharged battery. 8. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan.
412 WHAT TO DO IN EMERGENCIES CAUTION! (Continued) • Racing the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 35 mph (55 km/h). WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone.
WHAT TO DO IN EMERGENCIES 413 • The towing speed must not exceed 30 mph (48 km/h). CAUTION! Exceeding these towing limits may cause transmission failure. Vehicles equipped with AWD can be towed with the transmission in NEUTRAL and the rear wheels OFF the ground (or the rear driveshaft removed) with no limitation on speed or distance. CAUTION! • Do not attempt to tow this vehicle from the front with sling type towing equipment. Damage to the front fascia will result.
414 WHAT TO DO IN EMERGENCIES Towing This Vehicle Behind Another Vehicle With A Tow Dolly The manufacturer does not recommend that you tow this vehicle on a tow dolly. Vehicle damage may occur.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 2.7L . . . . . . . . . . . . . 417 䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . 423 䡵 Engine Compartment — 3.5L . . . . . . . . . . . . . 418 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 423 䡵 Engine Compartment — 5.7L . . . . . . . . . . . . . 419 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 426 䡵 Onboard Diagnostic System — OBD II . . . . . . 420 ▫ Engine Air Cleaner Filter . . . . . . . . . .
416 MAINTAINING YOUR VEHICLE ▫ Windshield Washers/Headlight Washers — If Equipped . . . . . . . . . . . . . . . . . . . . . . 431 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . 432 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . 435 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . 440 ▫ Automatic Transmission . . . . . . . . . . . . . . . 442 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 417 ENGINE COMPARTMENT — 2.
418 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 3.
MAINTAINING YOUR VEHICLE 419 ENGINE COMPARTMENT — 5.
420 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 421 A loose, improperly installed, or damaged fuel filler cap may also turn on the MIL. EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration.
422 MAINTAINING YOUR VEHICLE the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station. before going to the I/M station. The I/M station can fail your vehicle because the MIL is on with the engine running. b. The MIL will not flash at all and will remain fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is ready and you can proceed to the I/M station.
MAINTAINING YOUR VEHICLE 423 NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. WARNING! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
424 MAINTAINING YOUR VEHICLE dipstick. Adding 1.0 qt (1.0 L) of oil when the reading is at the MIN mark will result in a MAX reading on these engines. oil when the reading is at the bottom of the “SAFE” range will result in an oil level at the top of the “SAFE” range on these engines. CAUTION! CAUTION! Overfilling or underfilling will cause oil aeration or loss of oil pressure. This could damage your engine. Overfilling or underfilling will cause oil aeration or loss of oil pressure.
MAINTAINING YOUR VEHICLE 425 Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API Certified and meet the requirements of Chrysler Material Standard MS-6395. Engine Oil Viscosity (SAE Grade) — 2.7L and 5.7L Engines SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy.
426 MAINTAINING YOUR VEHICLE The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to “Engine Compartment” in this section. Lubricants which do not have both, the engine oil certification mark and the correct SAE viscosity grade number should not be used.
MAINTAINING YOUR VEHICLE 427 Engine Air Cleaner Filter Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals. WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance.
428 MAINTAINING YOUR VEHICLE NOTE: The battery is stored under an access cover in the trunk. Remote battery terminals are located in the engine compartment for jump-starting. Battery Location WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water.
MAINTAINING YOUR VEHICLE 429 WARNING! (Continued) • The battery in this vehicle has a vent hose that should not be disconnected and should only be replaced with a battery of the same type (vented). CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case.
430 MAINTAINING YOUR VEHICLE WARNING! (Continued) • The air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced technician. Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product.
MAINTAINING YOUR VEHICLE 431 MOPAR威 Spray White Lube to assure quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed. Particular attention should also be given to hood latching components to insure proper function.
432 MAINTAINING YOUR VEHICLE When refilling the washer fluid reservoir, apply some washer fluid to a cloth or towel and wipe the wiper blades clean. This will help blade performance. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers.
MAINTAINING YOUR VEHICLE 433 inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required. WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Exhaust Gas” under “Safety Tips” in Section 2. The catalytic converter requires the use of unleaded fuel only.
434 MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may indicate severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE 435 Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the LOCK position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position. • You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.
436 MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush, and Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant (antifreeze) solution. Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals.
MAINTAINING YOUR VEHICLE 437 CAUTION! (Continued) • This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended. Adding Coolant Your vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to five years or 102,000 miles (170 000 km) before replacement.
438 MAINTAINING YOUR VEHICLE NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and will require more frequent engine coolant (antifreeze) changes. Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle.
MAINTAINING YOUR VEHICLE 439 Disposal of Used Coolant Used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children, do not store ethylene glycol-based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child, contact a physician immediately.
440 MAINTAINING YOUR VEHICLE If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check engine coolant (antifreeze) freeze point in the radiator and in the coolant recovery bottle. If engine coolant (antifreeze) needs to be added, contents of coolant recovery bottle must also be protected against freezing.
MAINTAINING YOUR VEHICLE 441 WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency. Master Cylinder - Brake Fluid Level Check Check the fluid level in the master cylinder immediately if the brake system warning light indicates system failure.
442 MAINTAINING YOUR VEHICLE Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter or moisture. CAUTION! Do not allow petroleum-based fluid to contaminate the brake fluid. Seal damage may result. Automatic Transmission Fluid Level Check Regular automatic transmission fluid level checks are not required. For this reason, the dipstick is omitted.
MAINTAINING YOUR VEHICLE 443 Fluid and Filter Changes Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals. If the transmission is disassembled for any reason, the fluid and filter should be changed. Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission performance. Use only manufacturer’s recommended transmission fluid.
444 MAINTAINING YOUR VEHICLE The front differential fill plug is located on the outer cover near the halfshaft attachment. To inspect the differential fluid level, remove the fill plug. The fluid level should be even with or slightly below the bottom of the hole. Fluid Changes Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals.
MAINTAINING YOUR VEHICLE 445 Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using MOPAR威 Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumulated on your vehicle, use MOPAR威 Super Kleen Bug and Tar Remover to remove. • Use MOPAR威 Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint.
446 MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to an accident or similar cause, which destroys the paint and protective coating, have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.
MAINTAINING YOUR VEHICLE 447 Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and MOPAR威 Total Clean or equivalent. Care should be taken to avoid soaking your leather upholstery with any liquid.
448 MAINTAINING YOUR VEHICLE quarter window equipped with the radio antenna. Do not use scrapers or other sharp instrument that may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1.
MAINTAINING YOUR VEHICLE 449 FUSES CAUTION! Integrated Power Module The Integrated Power Module (IPM) is located in the engine compartment. This module contains fuses and relays. Integrated Power Module • When installing the integrated power module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the integrated power module and possibly result in an electrical system failure.
450 MAINTAINING YOUR VEHICLE Cavity 1 2 3 4 5 6 7 8 9 Cartridge MiniFuse Fuse — 15 Amp Blue — 25 Amp Neutral — 25 Amp Neutral — 25 Amp Neutral — — — 25 Amp Neutral — — — 25 Amp Neutral — — Description Washer Motor Powertrain Control Module (PCM) Ignition Run/Start Cavity 10 11 12 Alternator/EGR Solenoid 13 — Ignition Coils/Injectors/ Short Runner Valve — Starter — 14 15 16 17 18 Cartridge Fuse 30 Amp Pink 30 Amp Pink MiniFuse — Description — 40 Amp Green 50 Amp Red — Anti-Lock Brake System (ABS
MAINTAINING YOUR VEHICLE 451 Cavity 19 20 21 22 Cartridge Fuse — — — — MiniFuse — — — — Description — — — — Rear Power Distribution Center There is also a power distribution center located in the trunk under the spare tire access panel. This center contains fuses and relays.
452 MAINTAINING YOUR VEHICLE CAUTION! Rear Power Distribution Center • When installing the power distribution center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating.
MAINTAINING YOUR VEHICLE 453 Cavity 1 6 Cartridge Fuse 60 Amp Yellow 40 Amp Green — 40 Amp Green 30 Amp Pink — 7 — 2 3 4 5 MiniFuse — — — — — 20 Amp Yellow 15 Amp Blue Description Ignition Off Draw (IOD) Integrated Power Module (IPM) — Integrated Power Module (IPM) Heated Seats - If Equipped Fuel Pump Rear Heated Seats - If Equipped Cavity 8 Cartridge MiniFuse Fuse — 15 Amp Blue 9 — 10 11 * 12 * 13 * 14 — — — — — 15 — 16 — 20 Amp Yellow — — — — 10 Amp Red 20 Amp Yellow — Description Diag
454 MAINTAINING YOUR VEHICLE Cavity 17 18 19 20 21 22 23 24 25 26 27 Cartridge MiniFuse Fuse — 20 Amp Yellow — 20 Amp Yellow — 10 Amp Red — — — — — — — — — — — — — — — 10 Amp Red Description Cluster Cavity 28 Selectable Power Outlet 29 Cartridge MiniFuse Fuse — 10 Amp Red — 5 Amp Orange Stop Lights — — — — — — — Occupant Restraint Controller (ORC) 30 — 10 Amp Red 31 32 33 34 — — — — — — — — Description Ignition Run Adaptive Cruise Control (ACC) - If Equipped/ Cluster/Electronic Stability Prog
MAINTAINING YOUR VEHICLE 455 Cavity 35 Cartridge MiniFuse Fuse — 5 Amp Orange 36 — 20 Amp Yellow 37 — 38 — 15 Amp Blue 10 Amp Red 39 — 10 Amp Red Description Antenna Module - If Equipped/Power Mirrors/Rain Sensor - If Equipped Hands-Free Phone - If Equipped/Video Monitor - If Equipped/Radio Transmission Analog Clock/Cargo Light/Satellite Receiver (SDARS) Video - If Equipped/Vehicle Information Module - If Equipped Heated Mirrors - If Equipped Cavity 40 Cartridge MiniFuse Fuse — 5 Amp Orange
456 MAINTAINING YOUR VEHICLE * Cavities 11, 12, and 13 contain self-resetting fuses (circuit breakers) that are only serviceable by an authorized dealer. The cluster, the driver seat switch (if equipped), and the memory module (if equipped) are fused by the 25-Amp circuit breaker in Cavity 11. The passenger seat switch (if equipped) is fused by the 25-Amp circuit breaker in Cavity 12.
MAINTAINING YOUR VEHICLE 457 NOTE: For lighted switches, see your authorized dealer for replacement instructions. All of the interior bulbs are glass wedge base or glass cartridge types. Aluminum base bulbs are not approved and should not be used for replacement. Exterior (300 Models) Bulb Number Low Beam Headlight . . . . . . . . . . . . . . . . . . . . . 9006 High Beam Headlight. . . . . . . . . . . . . . . . . . . . . 9005 Front Park/Turn Light . . . . . . . . . . . . . . . . . . . .
458 MAINTAINING YOUR VEHICLE Center High Mount Stop Light (CHMSL) . . . . . . . LED (Serviced at Authorized Dealer) Outside Mirror Turn Signal & Approach Lights . . . . . . . . . . LED (Serviced at Authorized Dealer) License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . W5W 3. Disconnect the bulb from the socket assembly and install the replacement bulb. 4. Reinstall the bulb and socket assembly into the headlight assembly, and then turn it clockwise.
MAINTAINING YOUR VEHICLE 459 3 — Park/Turn Light Bulb 4 — Inner Park Light Bulb 5 — Outer Park Light Bulb 7
460 MAINTAINING YOUR VEHICLE CAUTION! WARNING! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. A transient high tension occurs at the bulb sockets of HID headlights when the headlight switch is turned ON. It may cause serious electrical shock or electrocution if not serviced properly. See your authorized dealer for service.
MAINTAINING YOUR VEHICLE 461 Backup Light, Side Marker Light, and Tail/Stop Turn Light — 300 Models 4. Remove the remaining fastener from the back of the tail light assembly. 1. Open the Trunk. 5. Push the electrical connector locking tab to the side. 2. Remove two fasteners from the back of the tail light assembly. 6. Disconnect the electrical connector. 7 3. Pull back the trunk liner. 7. Pull the tail light assembly clear from the vehicle to access the bulbs.
462 MAINTAINING YOUR VEHICLE 8. Turn the appropriate bulb and socket assembly counterclockwise to remove it from the tail light assembly.
MAINTAINING YOUR VEHICLE 463 9. Disconnect the bulb from the socket assembly and install the replacement bulb. 10. Reinstall the bulb and socket assembly into the tail light assembly, and then turn it clockwise. 11. Reinstall the tail light assembly, fasteners, electrical connector, and trunk liner. 12. Close the trunk.
464 MAINTAINING YOUR VEHICLE Tail/Stop, Tail, Turn Signal Light, and Backup Light — 300C Models 4. Remove the remaining fastener from the back of the tail light assembly. 1. Open the Trunk. 5. Push the electrical connector locking tab to the side. 2. Remove two fasteners from the back of the tail light assembly. 6. Disconnect the electrical connector. 3. Pull back the trunk liner.
MAINTAINING YOUR VEHICLE 465 7. Pull the tail light assembly clear from the vehicle to access the bulbs. Turn bulb sockets counterclockwise to remove. 8. Turn the appropriate bulb and socket assembly counterclockwise to remove it from the tail light assembly.
466 MAINTAINING YOUR VEHICLE 3 — Turn Signal Light Bulb 4 — Backup Light Bulb 9. Disconnect the bulb from the socket assembly and install the replacement bulb. 10. Reinstall the bulb and socket assembly into the tail light assembly, and then turn it clockwise.
MAINTAINING YOUR VEHICLE 467 11. Reinstall the tail light assembly, fasteners, electrical connector, and trunk liner. 12. Close the trunk. License Light 1. Remove the screws securing the light to the rear fascia. 2. Remove the bulb and socket assembly. 3. Disconnect the bulb from the socket assembly and install the replacement bulb. 1 — License Light Bulb 2 — Socket 4. Reinstall the bulb and socket assembly. 5. Reattach the light to the rear fascia, and then install the screws.
468 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES U.S. Fuel (Approximate) 2.7 Liter Engine 3.5 Liter Engine without All Wheel Drive 3.5 Liter Engine with All Wheel Drive 5.7 Liter Engine Engine Oil with Filter 2.7 Liter Engine (SAE 5W-20, API Certified) 3.5 Liter Engine (SAE 10W-30, API Certified) 5.7 Liter Engine (SAE 5W-20, API Certified) 18 18 19 19 Gallons Gallons Gallons Gallons 6.0 Quarts 6.0 Quarts 7.0 Quarts Metric 68 68 72 72 Liters Liters Liters Liters 5.7 Liters 5.7 Liters 6.
MAINTAINING YOUR VEHICLE 469 Cooling System * 2.7 Liter Engine (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) 3.5 Liter Engine without All Wheel Drive (MOPAR威 Antifreeze/ Coolant 5 Year/100,000 Mile Formula) 3.5 Liter Engine with All Wheel Drive (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) 5.7 Liter Engine without Severe Duty II Cooling System (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) 5.
470 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil (2.7L Engine) Engine Oil (3.5L Engine) Engine Oil (5.7L Engine) Spark Plugs (2.7L Engine) Spark Plugs (3.5L Engine) Spark Plugs (5.7L Engine) Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
MAINTAINING YOUR VEHICLE 471 Component Oil Filter (2.7L, 3.5L, and 5.7L Engines) Fuel Selection (2.7L Engine) Fuel Selection (3.5L and 5.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . 474 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 474 ▫ Required Maintenance Intervals . . . . . . . . . .
M A I N T E N A N C E 474 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 475 M A NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or six months, whichever comes first.
M A I N T E N A N C E S C H E D U L E S 8 476 MAINTENANCE SCHEDULES • Check the fluid levels of coolant reservoir, brake master cylinder, power steering, and transmission, and add as needed. • Check all lights and other electrical items for correct operation. At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines. CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle.
MAINTENANCE SCHEDULES 477 M 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
M 478 MAINTENANCE SCHEDULES A I N 18,000 Miles (30,000 km) or T 18 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ Inspect the rear axle fluid. Inspect the S C H E D U L E S 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
MAINTENANCE SCHEDULES 479 M 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Replace the air conditioning filter (if equipped) ❏ Inspect the rear axle fluid. Inspect the front axle fluid — All Wheel Drive (AWD).
M 480 MAINTENANCE SCHEDULES A I N 42,000 Miles (70,000 km) or T 42 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
MAINTENANCE SCHEDULES 481 M 54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the spark plugs (2.7L and 5.7L Engines). Replace the air conditioning filter (if equipped) Inspect the brake linings; replace if necessary. Adjust parking brake on vehicles equipped with four-wheel disc brakes.
M 482 MAINTENANCE SCHEDULES A I N 66,000 Miles (110,000 km) or T 66 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
MAINTENANCE SCHEDULES 483 M 78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
M 484 MAINTENANCE SCHEDULES A I N 90,000 Miles (150,000 km) or 90 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ Replace the engine air cleaner filter. C ❏ Replace the spark plugs (2.7L and 5.7L Engines). E ❏ Inspect and replace PCV valve if necessary. † S C H E D U L E S ❏ Inspect the rear axle fluid. Inspect the front axle fluid — All Wheel Drive (AWD). ❏ Inspect the transfer case fluid — All Wheel Drive (AWD).
MAINTENANCE SCHEDULES 485 M 96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Replace the air conditioning filter (if equipped) ❏ Inspect the brake linings; replace if necessary. ❏ Inspect the CV joints. ❏ Inspect exhaust system.
M 486 MAINTENANCE SCHEDULES A I N 108,000 Miles (180,000 km) or 108 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. C E ❏ Replace the air conditioning filter (if equipped) S C H E D U L E S 114,000 Miles (190,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter.
MAINTENANCE SCHEDULES 487 M 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the air conditioning filter (if equipped) Replace the spark plugs (2.7L and 5.7L Engines). Inspect the brake linings; replace if necessary. Adjust parking brake on vehicles equipped with four-wheel disc brakes. Inspect the CV joints. Inspect exhaust system.
M 488 MAINTENANCE SCHEDULES A I N 132,000 Miles (220,000 km) or T 132 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ If using your vehicle for any of the S C H E D U L E S 138,000 Miles (230,000 km) or 138 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
MAINTENANCE SCHEDULES 489 M 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Replace the air conditioning filter (if equipped) ❏ Inspect the brake linings; replace if necessary. ❏ Inspect the CV joints. ❏ Inspect exhaust system.
M A I N T E N A N C E S C H E D U L E S 8 490 MAINTENANCE SCHEDULES † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 493 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 495 ▫ Prepare For The Appointment . . . . . . . . . . . 493 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 495 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 493 䡵 Warranty Information (U.S. Vehicles Only) . . . .
492 IF YOU NEED CONSUMER ASSISTANCE 䡵 Publication Order Forms . . . . . . . . . . . . . . . . 497 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 499 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 498 ▫ Temperature Grades . . . . . . . . . . . . . . . . . . 499 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 493 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
494 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealership. They want to know if you need assistance. • If an authorized dealership is unable to resolve the concern, you may contact the manufacturer’s customer center.
IF YOU NEED CONSUMER ASSISTANCE 495 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
496 IF YOU NEED CONSUMER ASSISTANCE WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. WARRANTY INFORMATION (U.S.
IF YOU NEED CONSUMER ASSISTANCE 497 To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov. In Canada If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately.
498 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-bystep troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.
IF YOU NEED CONSUMER ASSISTANCE 499 Treadwear The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
500 IF YOU NEED CONSUMER ASSISTANCE WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
INDEX 10
502 INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . . 332 ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . 334 Adaptive Cruise Control (ACC) (Cruise Control) . . 154 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 437 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 375 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 431 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 373 Adjustable Pedals . . . . . . . . . . . . . . . . .
INDEX 503 Auto Unlock, Doors . . . . . . . . . . . . . . . . . . . . . . . 31 Auto Up Power Windows . . . . . . . . . . . . . . . . . . 37 Automatic Dimming Mirror . . . . . . . . . . . . . . . . . 85 Automatic Door Locks . . . . . . . . . . . . . . . . . . . 30,31 Automatic Headlights . . . . . . . . . . . . . . . . . . . . 137 Automatic Oil Change Indicator . . . . . . . . . . 209,225 Automatic Temperature Control (ATC) . . . . . . . . . 297 Automatic Transaxle Special Additives . . . . . . . . . . . . .
504 INDEX Brake, Parking . . . . . . . . . . . . . . . . . . . . . . . . . . 332 Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . 440 Anti-Lock (ABS) . . . . . . . . . . . . . . . . . . . . . . . 334 Fluid Check . . . . . . . . . . . . . . . . . . . . . . . 441,471 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . 441 Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332 Warning Light . . . . . . . . . . . . . . . . . . . . . . . . 212 Brakes . . . . . . . . .
INDEX 505 Cleaning Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 446 Windshield Wiper Blades . . . . . . . . . . . . . . . . 431 Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . 294 Clock . . . . . . . . . . . . . . . . . . . . . 237,239,253,257,266 Coin Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 Compact Disc (CD) Maintenance . . . . . . . . . . . . . 292 Compact Spare Tire . . . . . . . . . . . . . . . . . . . . . . 353 Compass . . . . . . . . . .
506 INDEX Daytime Brightness, Interior Lights . . . . . . . . . . . 143 Daytime Running Lights . . . . . . . . . . . . . . . . . . . 140 Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . . . 422 Deck Lid, Emergency Release . . . . . . . . . . . . . . . . 40 Deck Lid, Power Release . . . . . . . . . . . . . . . . . . . 39 Defroster, Rear Window . . . . . . . . . . . . . . . . . . . 198 Defroster, Windshield . . . . . . . . . . . . . . . . 78,295,301 Delay (Intermittent) Wipers . . . . . . . . .
INDEX 507 Electronic Vehicle Information Center (EVIC) . . . . 220 Emergency Deck Lid Release . . . . . . . . . . . . . . . . 40 Emergency, In Case of Freeing Vehicle When Stuck . . . . . . . . . . . . . . . 411 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 396 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 408 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . 396 Towing . . . . . . . . . . . . .
508 INDEX Event Data Recorder . . . . . . . . . . . . . . . . . . . . . . 63 Exhaust Gas Caution . . . . . . . . . . . . . . . . 76,374,433 Exhaust System . . . . . . . . . . . . . . . . . . . . . . . 76,432 Exterior Folding Mirrors . . . . . . . . . . . . . . . . . . . 87 Exterior Lighting . . . . . . . . . . . . . . . . . . . . . . . . 136 Exterior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Filters Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 427 Air Conditioning . .
INDEX 509 Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371 Filler Cap (Gas Cap) . . . . . . . . . . . . . . . . . . . . 375 Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370 Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 Materials Added . . . . . . . . . . . . . . . . . . . . . . . 373 Methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371 Octane Rating . . . . . . . . . . . . . . . . . . . . . . 370,470 Requirements . . . . . . .
510 INDEX Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . 127 Headlight Washers . . . . . . . . . . . . . . . . . . . . . . . 431 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 460 Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 458 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 447 Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 511 Integrated Power Module (Fuses) . . . . . . . . . . . . 449 Interior Appearance Care . . . . . . . . . . . . . . . . . . 446 Interior Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . 449 Interior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 142 Intermittent Wipers (Delay Wipers) . . . . . . . . . . . 144 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Jack Location . . . . . Jack Operation . . . . Jacking Instructions Jump Starting . . . . . . . .
512 INDEX Bulb Replacement . . . . . . . . . . . . . . . . . . . 456,458 Courtesy/Reading . . . . . . . . . . . . . . . . . . . 142,181 Cruise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 Daytime Running . . . . . . . . . . . . . . . . . . . . . . 140 Dimmer Switch, Headlight . . . . . . . . . . . . . 140,142 Electronic Stability Program (ESP) Indicator . . . 341 Electronic Throttle Control Warning . . . . . . . . . 216 Engine Temperature Warning . . . . . . . . . . . . . .
INDEX 513 Turn Signal . . . . . . . . . . . . . . . . . . . 78,140,141,208 Vanity Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218 Warning (Instrument Cluster Description) . . . . . 208 Load Leveling System . . . . . . . . . . . . . . . . . . . . 199 Loading Vehicle . . . . . . . . . . . . . . . . . . . . . . 377,379 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 Tires . . . . . . . . . . . . . . . . .
514 INDEX Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Vanity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Modifications/Alterations, Vehicle . . . . . . . . . . . . . 7 Monitor, Tire Pressure System . . . . . . . . . . . . . . . 361 Mopar Parts . . . . . . . . . . . . . . . . . . . . . . . . . 422,496 MTBE/ETBE . . . . . .
INDEX 515 Overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319 Overhead Console . . . . . . . . . . . . . . . . . . . . . . . 180 Overheating, Engine . . . . . . . . . . . . . . . . . . . 214,396 Owner’s Manual (Operator Manual) . . . . . . . . . 4,497 Paint Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444 Panic Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Park Sense System, Rear . . . . . . . . . . . . . . . . . . . 177 Parking Brake . . . . . . . .
516 INDEX Radio Operation . . . . . . . . . . . . . . . . . . . . . . . . 293 Radio Remote Controls . . . . . . . . . . . . . . . . . . . . 291 Radio, Satellite (uconnect gps) . . . . . . . . . . . . 282,288 Rain Sensitive Wiper System . . . . . . . . . . . . . . . . 146 Rear Cupholder . . . . . . . . . . . . . . . . . . . . . . . . . 194 Rear Park Sense System . . . . . . . . . . . . . . . . . . . 177 Rear Seat, Folding . . . . . . . . . . . . . . . . . . . . . . . 129 Rear Window Defroster . . . . . . .
INDEX 517 Rotation, Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 360 Safety Checks Inside Vehicle . . . . . . . . . . . . . . . . . 77 Safety Checks Outside Vehicle . . . . . . . . . . . . . . . 78 Safety Defects, Reporting . . . . . . . . . . . . . . . . . . 496 Safety, Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . 76 Safety Information, Tire . . . . . . . . . . . . . . . . . . . 342 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Satellite Radio Antenna .
518 INDEX Security Alarm (Theft Alarm) . . . . . . . . . . . . . . . . 18 Selection of Coolant (Antifreeze) . . . . . . . . . . 436,470 Selection of Oil . . . . . . . . . . . . . . . . . . . . . . . . . 425 Self-Sealing Tires . . . . . . . . . . . . . . . . . . . . . . . . 358 Sentry Key (Immobilizer) . . . . . . . . . . . . . . . . . . . 15 Sentry Key Programming . . . . . . . . . . . . . . . . . . . 17 Sentry Key Replacement . . . . . . . . . . . . . . . . . . . 16 Service Assistance . . . . . . . . . .
INDEX 519 Engine Fails to Start . . . . . . . . . . . . . . . . . . . . 311 Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Starting and Operating . . . . . . . . . . . . . . . . . . . . 309 Starting Procedures . . . . . . . . . . . . . . . . . . . . . . 309 Steering Column Controls . . . . . . . . . . . . . . . . . . . . . . 140 Column Lock . . . . . . . . . . . . . . . . . . . . . . . . . 147 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . 331,332 Tilt Column . . . . . .
520 INDEX Aging (Life of Tires) . . . . . . . . . . . . . . . . . . . . 356 Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 350 Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358 Changing . . . . . . . . . . . . . . . . . . . . . . . . . 397,400 Compact Spare . . . . . . . . . . . . . . . . . . . . . . . . 353 Flat Changing . . . . . . . . . . . . . . . . . . . . . . . . 397 General Information . . . . . . . . . . . . . . . . . . . . 350 High Speed . . . . . . . . . . .
INDEX 521 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . 380 Cooling System Tips . . . . . . . . . . . . . . . . . . . . 392 Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383 Minimum Requirements . . . . . . . . . . . . . . . . . 386 Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391 Trailer and Tongue Weight . . . . . . . . . . . . . . . 385 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390 Trailer Towing Guide . . . . . .
522 INDEX Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Variance, Compass . . . . . . . . . . . . . . . . . . . . . . . 230 Vehicle Certification Label . . . . . . . . . . . . . . . . . 378 Vehicle Identification Number (VIN) . . . . . . . . . . . . 6 Vehicle Loading . . . . . . . . . . . . . . . . . . . 346,377,379 Vehicle Modifications/Alterations . . . . . . . . . . . . . . 7 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
2009 300 300 2009 owner’s manual Chrysler LLC 81-026-0943 147915 09 LX300C OM.indd 1 Second Edition Printed in U.S.A.
