Owner's Manual

ManualsBrandsChrysler ManualsAutomobileChrysler 2009 Chrysler 300C

121411 LX-300C OM EN.indd 1121411 LX-300C OM EN.indd 1 4/1/08 7:55:09 AM4/1/08 7:55:09 AM

Summary of content (537 pages)

PAGE 1
PAGE 2
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
PAGE 3
SECTION TABLE OF CONTENTS PAGE 1 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 4
PAGE 5
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 6 ..............
PAGE 6
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
PAGE 7
INTRODUCTION 5 1
PAGE 8
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is on the left front corner of the instrument panel.
PAGE 9
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
PAGE 10
PAGE 11
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 䡵 Vehicle Security Alarm System — If Equipped . . 18 ▫ Wireless Ignition Node (WIN) . . . . . . . . . . . . 12 ▫ Rearming Of The System . . . . . . . . . . . . . . . . 18 ▫ FOB With Integrated Key . . . . . . . . . . . . . . . 13 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . 18 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . 14 ▫ To Disarm The System . . . . . .
PAGE 12
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 24 䡵 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 ▫ Programming Additional RKE Transmitters . . . 25 ▫ Power Windows . . . . . . . . . . . . . . . . . . . . . . 37 ▫ RKE Transmitter Battery Service . . . . . . . . . . . 25 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 41 ▫ General Information . . . . . . . . . . . . . . . . . . .
PAGE 13
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Seat Belts And Pregnant Women . . . . . . . . . . 53 ▫ Transporting Passengers . . . . . . . . . . . . . . . . 78 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . 53 ▫ Lock Your Vehicle . . . . . . . . . . . . . . . . . . . . . 79 ▫ Driver And Front Passenger Supplemental Restraint System (SRS) - Airbag . . . . . . . . . . . 54 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . 79 ▫ Event Data Recorder (EDR) . . . . . . . . .
PAGE 14
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Fob with Integrated Key and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the double-sided integrated key into the ignition switch with either side up.
PAGE 15
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Fob with Integrated Key The Fob with Integrated Key (FOBIK) operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and a valet key, which stores in the rear of the Fob. 2 The valet key allows for entry into the vehicle should the battery in the vehicle or the Fob go dead. The valet key is also for locking the glove box. You can keep the valet key with you when valet parking.
PAGE 16
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Ignition Key Removal Place the shift lever in PARK. Turn the key to the LOCK position and then remove the key. NOTE: • For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for 10 minutes after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature.
PAGE 17
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Key-In-Ignition Reminder If you open the driver’s door and the key is in the ignition, a chime will sound to remind you to remove the key. NOTE: The Key-In-Ignition reminder only sounds when the ignition key is placed in the LOCK or ACC position. SENTRY KEY姞 IMMOBILIZER SYSTEM The Sentry Key威 Immobilizer system prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated.
PAGE 18
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • The Sentry Key威 Immobilizer system is not compatible with aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. • Exxon/Mobil Speedpass™, additional RKE transmitters, or any other transponder-equipped components on the same key chain will not cause a fault unless the additional part is physically held against the RKE transmitter being used to start the vehicle.
PAGE 19
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 NOTE: When having the Sentry Key威 Immobilizer system serviced, bring all vehicle RKE transmitters with you to an authorized dealer. Customer Key Programming If you have two valid RKE transmitters with integrated keys, you can program new RKE transmitters to the system by performing the following procedure: 1.
PAGE 20
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information The Sentry Key威 system complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received, including interference that may cause undesired operation.
PAGE 21
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 To Disarm the System Either press the UNLOCK button on the RKE transmitter or insert a valid ignition key into the ignition switch and turn the key to the ON position. system will arm regardless of whether you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the system. NOTE: • The driver’s door key cylinder and the trunk button on the RKE transmitter cannot arm or disarm the system.
PAGE 22
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ILLUMINATED ENTRY SYSTEM The courtesy lights will turn on when you use the Remote Keyless Entry (RKE) transmitter or open any door. This feature also turns on the approach lighting in the outside mirrors (if equipped). Refer to “Outside Mirrors with Turn Signal and Approach Lighting – If Equipped” under “Mirrors” in Section 3.
PAGE 23
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Remote Key Unlock, Driver Door/All Doors 1st Press This feature lets you program the system to unlock either the driver’s door or all doors on the first press of the UNLOCK button on the RKE transmitter.
PAGE 24
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Release both buttons at the same time. 3. Test the feature while outside of the vehicle by pressing the LOCK/UNLOCK buttons on the RKE transmitter with the ignition switch in the LOCK position and the key removed. 4. Repeat these steps if you want to return this feature to its previous setting. NOTE: Pressing the LOCK button on the RKE transmitter while you are inside the vehicle will activate the security alarm.
PAGE 25
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 4. Repeat these steps if you want to return this feature to its previous setting. NOTE: Pressing the LOCK button on the RKE transmitter while you are in the vehicle will activate the security alarm. Opening a door with the security alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the security alarm.
PAGE 26
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the following procedure: 1. Press the LOCK button on a programmed RKE transmitter for at least four seconds, but no longer than 10 seconds. Then, press the PANIC button while still holding the LOCK button. 2. Release both buttons at the same time. 3.
PAGE 27
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 NOTE: • The interior lights will turn off if you turn the ignition switch to the ACC or ON position while the Panic Alarm is activated. However, the exterior lights and horn will remain on. • You may need to be less than 35 ft (11 m) from the vehicle when using the RKE transmitter to turn off the Panic Alarm due to the radio frequency noises emitted by the system. Programming Additional RKE Transmitters Refer to Sentry Key威 “Customer Key Programming.
PAGE 28
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Battery access is through a door located on the rear of the fob. Insert a small, flat blade screwdriver into the slot and gently pry open the access door. 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. Reposition the access door panel over the battery opening and snap into place.
PAGE 29
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 If your RKE transmitter fails to operate from a normal distance, check for these two conditions: 1. A weak battery in the RKE transmitter. The expected life of the battery is a minimum of three years. How to Use Remote Start All of the following conditions must be met before the engine will remote start: • Shift lever in PARK 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios.
PAGE 30
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Enter Remote Start Mode Press and release the REMOTE START button on the RKE transmitter twice, within five seconds. The parking lights will flash and the horn will honk twice (if programmed). Then, the engine will start and the vehicle will remain in the Remote Start mode for a 15-minute cycle. To Exit Remote Start Mode without Driving the Vehicle Allow the engine to run for the entire 15-minute cycle.
PAGE 31
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 To Turn Off the Engine While in Remote Start Mode Press and release the REMOTE START button one time. 2 NOTE: To avoid inadvertent shut downs, the system will disable the one time press of the REMOTE START button for two seconds after receiving a valid Remote Start request. DOOR LOCKS Manual Door Locks To lock each door, push the door lock plunger on each door trim panel downward.
PAGE 32
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • When leaving the vehicle, always remove the key from the ignition and lock your vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death. • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons.
PAGE 33
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 is open, the key is in the ignition, and the ignition is in the LOCK or ACC position, a chime will sound as a reminder to remove the key.
PAGE 34
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Depress the power door LOCK switch to lock the doors. 4. A single chime will indicate the completion of the programming. 5. Repeat these steps if you want to return this feature to its previous setting. NOTE: Use the Automatic Door Locks feature in accordance with local laws. Automatic Unlock Doors on Exit The doors will unlock automatically on vehicles with power door locks if: 1. The Automatic Unlock Doors On Exit feature is enabled. 2.
PAGE 35
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 • For vehicles not equipped with the EVIC, perform the following procedure: 1. Close all doors and place the key in the ignition. 2. Cycle the ignition switch between LOCK and ON and then back to LOCK four times ending up in the LOCK position. 3. Depress the power door UNLOCK switch to unlock the doors. 4. A single chime will indicate the completion of the programming. 5. Repeat these steps if you want to return this feature to its previous setting.
PAGE 36
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Doors 1st Press”, all doors will unlock if any door handle is grasped. Refer to “Remote Key Unlock” under “Personal Settings (Customer-Programmable Features)” in the “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. • If you accidentally lock your RKE transmitter in the vehicle using the door panel switch, ALL doors will unlock and the horn will chirp three times after all doors are closed.
PAGE 37
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 same lock/unlock and chirping sound that you would experience if you accidentally locked your RKE transmitter in the vehicle. 2. Open the door and repeat Step 1 two more times (three times total). The doors will remain locked; no audible warnings will occur. 2. Insert the tip of the valet key (or alike) into the child lock control and pull it upward. NOTE: For valet key information, refer to “A Word About Your Keys” in this section.
PAGE 38
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: When the Child Protection Door Lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position. WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. Failure to follow this warning may result in serious injury or death.
PAGE 39
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WINDOWS Power Windows The window controls on the driver’s door control all the door windows. Child Lock Control 3. Repeat Steps 1 and 2 for the opposite rear door. NOTE: After disengaging the Child Protection Door Lock system, always test the door from the inside to make certain it is in the desired position.
PAGE 40
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There are single window controls on each passenger door trim panel, which operate the passenger door windows. The window controls will operate only when the ignition switch is in the ON or ACC position. WARNING! Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death.
PAGE 41
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 AUTO-Up Feature with Anti–Pinch Protection — If Equipped Lift the window switch to the second detent, release, and the window will go up automatically. programmable. Refer to “Delay Power Off to Accessories Until Exit,” under “Personal Settings (CustomerProgrammable Features),” under “Electronic Vehicle Information Center (EVIC) – If Equipped” in Section 4.
PAGE 42
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing. Window Lockout Switch The window lockout switch on the driver’s door trim panel allows you to disable the window controls on the passenger doors. To disable the window controls, press and release the window lockout button (setting it in the DOWN position).
PAGE 43
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Reset Anytime the vehicle battery is disconnected or goes dead, the AUTO-up function will be disabled. To reactivate the AUTO-up feature, perform the following procedure after vehicle power is restored: 1. Pull the window switch up to close window completely and continue to hold the switch up for an additional two seconds after the window is closed. 2.
PAGE 44
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK LOCK AND RELEASE The trunk lid can be released from inside the vehicle by pressing the TRUNK RELEASE button located on the instrument panel to the left of the steering wheel. NOTE: The transmission must be in PARK before the switch will operate. The trunk lid can be released from outside the vehicle by pressing the TRUNK button on the Remote Keyless Entry (RKE) transmitter twice within five seconds.
PAGE 45
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 TRUNK SAFETY WARNING WARNING! 2 Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat. If trapped in the trunk, children can die from suffocation or heat stroke.
PAGE 46
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE and passengers seated next to a window, and the optional supplemental front seat-mounted side airbags. If you will be carrying children too small for adult-size belts, your seat belts also can be used to hold infant and child restraint systems. Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible.
PAGE 47
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 normal conditions. However, in a collision, the belt will lock and reduce your risk of striking the inside of the vehicle or being thrown out. WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
PAGE 48
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the front seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.
PAGE 49
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 WARNING! WARNING! (Continued) • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
PAGE 50
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision.
PAGE 51
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.).
PAGE 52
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In the rear seat, move toward the center of the seat to position the belt away from your neck. 1. Position the latch plate as close as possible to the anchor point. Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove any slack from the seat belts in the event of a collision.
PAGE 53
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Enhanced Seat Belt Reminder System (BeltAlert姞) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert威) will alert the driver to buckle their seat belt. The driver should also instruct all other occupants to buckle their seat belts.
PAGE 54
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have successfully completed the programming. BeltAlert威 can be reactivated by repeating this procedure. NOTE: Although BeltAlert威 has been deactivated, the Seat Belt Reminder Light will continue to illuminate as long as the driver’s seat belt is unbuckled. Automatic Locking Mode — If Equipped In this mode, the shoulder belt is automatically prelocked.
PAGE 55
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision.
PAGE 56
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver and Front Passenger Supplemental Restraint System (SRS) - Airbag This vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s airbag is mounted in the center of the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers.
PAGE 57
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity. WARNING! • Do not put anything on or around the front airbag covers or attempt to open them. You may damage the airbags and you could be injured because the airbags are no longer functional.
PAGE 58
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the vehicle is equipped with supplemental side curtain airbags, they are located above the side windows. Their covers are also labeled SRS AIRBAG. If the vehicle is equipped with supplemental front seatmounted side airbags, they are marked with an SRS label sewn into the outboard side of the seat. Window Airbag SRS Label Location NOTE: Airbag covers may not be obvious in the interior trim, but they will open to allow airbag deployment.
PAGE 59
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 WARNING! WARNING! (Continued) • If your vehicle is equipped with supplemental front seat-mounted side airbags, do not use accessory seat covers or place objects between you and the seat airbags; the performance could be adversely affected and/or objects could be pushed into you, causing serious injury. • If your vehicle is equipped with supplemental front seat-mounted side airbags, do not attach cupholders or any other objects on or around the door.
PAGE 60
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Side curtain and seat airbags also work with seat belts to improve occupant protection. While the seat belts are designed to protect you in many types of collisions, the front airbags will deploy in moderate to severe frontal collisions.
PAGE 61
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 seat as far back as possible and use the proper child restraint. (Refer to information on Child Restraints in this section.) 5. You should read the instructions provided with your child restraint to make sure that you are using it properly. 6. All occupants should use their seat belts properly. 7. The driver and front passenger seats should be moved back as far as practical to allow the airbags time to inflate. 8.
PAGE 62
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag System Components The airbag system consists of the following: • Occupant Restraint Controller (ORC) • Side Remote Acceleration Sensors (if equipped) • Airbag Warning Light • Driver Airbag • Front Passenger Airbag • Supplemental Side Curtain Airbags above Side Windows (if equipped) • Supplemental Front Seat-Mounted Side Airbags (if equipped) • Steering Wheel and Column • Instrument Panel • Interconnecting Wiring • Seat Belt Reminder Light • Knee Impact
PAGE 63
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 • The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or ON positions. These include all of the items listed above except the knee bolster, the instrument panel, and the steering wheel and column. If the key is in the LOCK position, in the ACC position, or not in the ignition, the airbags are not on and they will not inflate.
PAGE 64
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE their full size. The bags fully inflate in about 50 to 70 ms. This is about half of the time that it takes to blink your eyes. The bags then quickly deflate while helping to restrain the driver and front passenger. The driver’s front airbag gas is vented through vent holes in the sides of the airbag. The passenger’s front airbag gas is vented through vent holes in the sides of the airbag.
PAGE 65
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 between the occupant and the door. The airbag inflates at a very high speed and with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the front seat-mounted side airbag inflates. This especially applies to children. The following requirements must be strictly adhered to: • Do not make any modifications to the front seat components, assembly, or to the seat cover in any way.
PAGE 66
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If a Deployment Occurs The airbag system is designed to deploy when the ORC detects a moderate to severe collision to help restrain the driver and front passenger and then to immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system.
PAGE 67
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Enhanced Accident Response System In the event of an impact that causes airbag deployment, with the vehicle stopped, and the vehicle communication network intact, and the power intact, the Enhanced Accident Response System performs the following functions: • Cuts off fuel to the engine. • Flashes hazard lights. • Turns on the interior lights, which remain on as long as the battery has power or until the ignition key is removed.
PAGE 68
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. Airbag Warning Light You will want to have the airbags ready to inflate for your protection in an impact.
PAGE 69
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 In conjunction with other data gathered during a complete accident investigation, the electronic data may be used by Chrysler LLC and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle performance.
PAGE 70
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Data parameters that may be recorded: • Transmission gear selection • Diagnostic trouble code(s) and warning light status for electronically-controlled safety systems, including the airbag system • Cruise control status • Airbag disable light status (if equipped) • ⬙Time⬙ of airbag deployment (in terms of ignition cycles and vehicle mileage) • Airbag deployment level (if applicable) • Impact acceleration and angle • Seat belt status • Brake status (service
PAGE 71
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.
PAGE 72
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE “LATCH — Child Seat Anchorage System (Lower Anchors and Tether for CHildren)” in this section. WARNING! Rearward-facing child seats must NEVER be used in the front seat of a vehicle with the front passenger airbag unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position.
PAGE 73
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back. NOTE: For additional information, refer www.seatcheck.org or call 1–866–SEATCHECK.
PAGE 74
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it before you buy it. • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits.
PAGE 75
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 connection to the top tether anchorages have been available for some time. For some older child restraints, many child restraint manufacturers offer add-on tether strap kits or retrofit kits. You are urged to take advantage of all the available attachments provided with your child restraint in any vehicle. All three rear-seating positions have lower anchorages that are capable of accommodating LATCH-compatible child seats.
PAGE 76
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Again, carefully follow the installation instructions that are provided with the child restraint system. The rear seat lower anchorages are round bars located at the rear of the seat cushion where it meets the seatback and are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces.
PAGE 77
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 NOTE: • Ensure that the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. • When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children. It is recommended that before installing the child restraint, buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach.
PAGE 78
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat belts with an automatic locking retractor have a distinctive label on the seat belt webbing. The seat belt must be in the Automatic Locking mode in order to enable a child restraint to be tightly installed. Refer to “Automatic Locking Mode” in this section. A locking clip should not be necessary once the automatic locking feature is enabled. Position the shoulder and lap belt on the child restraint.
PAGE 79
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 NOTE: Ensure that the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Tether Strap Mounting 2.
PAGE 80
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration within the limits of local traffic laws, contributes to a good break-in. Wide-open throttle acceleration in low gear can be detrimental and should be avoided.
PAGE 81
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly.
PAGE 82
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you are required to drive with the trunk open, make sure that all windows are closed and the climate control BLOWER switch is set at high speed. DO NOT use the recirculation mode. The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
PAGE 83
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable. Periodic Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread.
PAGE 84
PAGE 85
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 ▫ Tilt Mirrors In Reverse — If Equipped . . . . . . 92 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 89 ▫ Power Mirrors . . . . . . . . . . . . . . . . . . . . . . . 93 ▫ Automatic Dimming Inside Mirror — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 90 ▫ Heated Power Mirrors — If Equipped . . . . . . 93 ▫ Outside Mirrors . . . . . . . . . . . . .
PAGE 86
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Advanced Phone Connectivity . . . . . . . . . . . 112 ▫ Heated Seats — If Equipped . . . . . . . . . . . . 131 ▫ Things You Should Know About Your UConnect威 System . . . . . . . . . . . . . . . . . . . 113 ▫ Folding Rear Seat . . . . . . . . . . . . . . . . . . . . 133 ▫ General Information . . . . . . . . . . . . . . . . . . 122 䡵 Voice Recognition System (VR) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 87
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 ▫ Headlights On With Wipers (Available With Auto Headlights Only) . . . . . . . . . . . . . . . . 141 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . 148 ▫ SmartBeams — If Equipped . . . . . . . . . . . . . 141 ▫ Headlights On With Wipers (Available With Auto Headlights Only) . . . . . . . . . . . . . . . . 148 ▫ Headlight Time Delay . . . . . . . . . . . . . . . . . 142 ▫ Rain Sensing Wipers — If Equipped . . . . . . .
PAGE 88
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ To Vary The Speed Setting . . . . . . . . . . . . . . 156 ▫ Adaptive Cruise Control (ACC) Menu . . . . . 168 ▫ To Accelerate For Passing . . . . . . . . . . . . . . 157 ▫ Display Warnings And Maintenance . . . . . . . 171 䡵 Adaptive Cruise Control (ACC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 157 ▫ Precautions While Driving With ACC . . . . . . 174 ▫ Adaptive Cruise Control (ACC) Operation . . 160 ▫ General Information . . . .
PAGE 89
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 ▫ Using HomeLink威 . . . . . . . . . . . . . . . . . . . 189 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . 193 ▫ Reprogramming A Single HomeLink威 Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . 194 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 ▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . . 190 ▫ General Information . . . . . . . . . .
PAGE 90
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Trunk Mat — If Equipped . . . . . . . . . . . . . . 201 ▫ Electric Rear Window Defroster . . . . . . . . . . 201 䡵 Rear Window Features . . . . . . . . . . . . . . . . . . 201 䡵 Load Leveling System — If Equipped . . . . . . .
PAGE 91
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. The mirror should be adjusted while set in the day position (toward the windshield). 3 Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
PAGE 92
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Inside Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will illuminate to indicate when the dimming feature is activated. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
PAGE 93
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 WARNING! Vehicles and other objects seen in the passenger-side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger-side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger-side convex mirror. Outside Mirrors Folding Feature — If Equipped Some models have outside mirrors that are hinged.
PAGE 94
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The fourth (uppermost) LED supplies illuminated entry lighting, which turns on in both mirrors when you use the Remote Keyless Entry (RKE) transmitter or open any door. This LED shines outward to illuminate the front and rear door handles. It also shines downward to illuminate the area in front of the doors.
PAGE 95
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Power Mirrors The power mirror switch is located on the driver’s door trim panel next to the power door lock switch. A rotary knob selects the left mirror, right mirror or off position. After selecting a mirror, move the knob in the same direction you want the mirror to move. Use the center off position to guard against accidentally moving a mirror position.
PAGE 96
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is located on the sun visor. To use the mirror, rotate the sun visor downward and swing the mirror cover upward. The light turns on automatically. Closing the mirror cover turns off the light. HANDS-FREE COMMUNICATION (UConnect姞) — IF EQUIPPED NOTE: The sales code RER and REU radios contain an integrated Hands-Free Communication (UConnect威) system.
PAGE 97
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 NOTE: The UConnect威 system requires a cellular phone equipped with the Bluetooth威 ⬙Hands-Free Profile,⬙ Version 0.96 or higher. See the UConnect威 website for supported phones. NOTE: For UConnect威 customer support, visit the following websites: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.
PAGE 98
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Recognition Button Actual button location may vary with the radio. The individual buttons are described in the “Operation” section. The UConnect威 system can be used with any Hands-Free Profile certified Bluetooth威 cellular phone. See the UConnect威 website for supported phones. If your cellular phone supports a different profile (e.g., Headset Profile) you may not be able to use any UConnect威 features.
PAGE 99
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 • For each feature explanation in this section, only the combined form of the voice command is given. You can also break the commands into parts and say each part of the command when you are asked for it. For example, you can use the combined form voice command ⬙Phonebook New Entry,⬙ or you can break the combined form command into two voice commands: ⬙Phonebook⬙ and ⬙New Entry.
PAGE 100
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The following are general phone to UConnect威 system pairing instructions: • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Phone Pairing.⬙ • When prompted, after the beep, say ⬙Pair a Phone⬙ and follow the audible prompts. • You will be asked to say a four-digit Personal Identification Number (PIN), which you will later need to enter into your cellular phone. You can enter any four-digit PIN.
PAGE 101
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 • The system will prompt you to say the number you want to call. • For example, you can say ⬙234-567-8901⬙. • The UConnect威 system will confirm the phone number and then dial. The number will appear in the display of certain radios. Call by Saying a Name • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say “Call.⬙ • The system will prompt you to say the name of the person you want to call.
PAGE 102
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, enter the number designation (e.g., ⬙Home,⬙ ⬙Work,⬙ ⬙Mobile,⬙ or ⬙Pager⬙). This will allow you to store multiple numbers for each phonebook entry, if desired. • When prompted, recite the phone number for the phonebook entry that you are adding. After you are finished adding an entry into the phonebook, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu.
PAGE 103
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 • Depending on the maximum number of entries downloaded, there may be a short delay before the latest downloaded names can be used. Until then, if available, the previous downloaded phonebook is available for use. • Only the phonebook of the currently connected mobile phone is accessible. • Only the mobile phone’s phonebook is downloaded. SIM card phonebook is not part of the Mobile phonebook.
PAGE 104
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE book entry via Bluetooth威. Please see your phone Owner’s Manual for specific instructions on how to drop the Bluetooth威 connection. • If the phonebook entry is longer than 24 characters, it will only use the first 24 characters. Edit UConnect威 Phonebook Entries NOTE: • Editing names in the phonebook is recommended when the vehicle is not in motion. • Automatic downloaded phonebook entries cannot be deleted or edited. • Press the PHONE button to begin.
PAGE 105
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Delete.⬙ • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say ⬙List Names⬙ to hear a list of the entries in the phonebook from which you choose.
PAGE 106
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Automatic downloaded phonebook entries cannot be deleted or edited. List All Names in the UConnect威 Phonebook • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook List Names.⬙ • The UConnect威 system will play the names of all the phonebook entries, including the downloaded phonebook entries, if available.
PAGE 107
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cellular phone. Press the PHONE button to place the current call on hold and answer the incoming call.
PAGE 108
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Three-Way Calling To initiate three-way calling, press the VOICE RECOGNITION button while a call is in progress, and make a second phone call, as described under ⬙Making a Second Call While Current Call is in Progress.⬙ After the second call has established, press and hold the PHONE button until you hear a double beep, indicating that the two calls have been joined into one conference call.
PAGE 109
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 • After the ignition key is switched to OFF, a call can continue on the UConnect威 system for a certain duration, after which the call is automatically transferred from the UConnect威 system to the mobile phone. • An active call is automatically transferred to the mobile phone after the ignition key is switched to OFF. UConnect姞 System Features Language Selection To change the language that the UConnect威 system is using: • Press the PHONE button to begin.
PAGE 110
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say ⬙Emergency⬙ and the UConnect威 system will instruct the paired cellular phone to call the emergency number. This feature is supported in the U.S., Canada, and Mexico. NOTE: • The emergency number dialed is based on the country where the vehicle is purchased (911 for the U.S. and Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area.
PAGE 111
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 NOTE: • The towing assistance number dialed is based on the country where the vehicle is purchased (1-800-5282069 for the U.S., 1-877-213-4525 for Canada, 55-143454 for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico). • If supported, this number may be programmable on some systems. To do this, press the PHONE button and say “Setup”’, followed by “Towing Assistance”. Paging To learn how to page, refer to ⬙Working with Automated Systems.
PAGE 112
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE used for navigating through an automated customer service center menu structure, and to leave a number on a pager. You can also send stored UConnect威 phonebook entries as tones for fast and easy access to voice mail and pager entries. To use this feature, dial the number you wish to call and then press the VOICE RECOGNITION button and say, “Send.” The system will prompt you to enter the name or number and say the name of the phonebook entry you wish to send.
PAGE 113
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Phone and Network Status Indicators If available on the radio and/or on a premium display such as the instrument panel cluster, and supported by your cellular phone, the UConnect威 system will provide notification to inform you of your phone and network status when you are attempting to make a phone call using UConnect威. The status is given for roaming, network signal strength, phone battery strength, etc.
PAGE 114
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Advanced Phone Connectivity List Paired Cellular Phone Names Transfer Call to and from Cellular Phone The UConnect威 system allows ongoing calls to be transferred from your cellular phone to the UConnect威 system without terminating the call. To transfer an ongoing call from your UConnect威 paired cellular phone to the UConnect威 system or vice versa, press the VOICE RECOGNITION button and say ⬙Transfer Call.⬙ • Press the PHONE button to begin.
PAGE 115
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Select Another Cellular Phone This feature allows you to select and start using another phone paired with the UConnect威 system. • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Select Phone⬙ and follow the prompts. • You can also press the VOICE RECOGNITION button at any time while the list is being played, and then choose the phone that you wish to select.
PAGE 116
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers, the UConnect威 system Voice Training feature may be used. To enter this training mode, follow one of the two following procedures: From outside the UConnect威 mode (e.g.
PAGE 117
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 • Performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, French, and Spanish accents, the system may not always work for some.
PAGE 118
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the UConnect威 system. • Echo at the far end can sometimes be reduced by lowering the in-vehicle audio volume.
PAGE 119
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 3
PAGE 120
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
PAGE 121
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 3
PAGE 122
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home
PAGE 123
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call UConnect威 Tutorial try again voice training work yes 3
PAGE 124
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
PAGE 125
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 When you press the VR hard-key, you will hear a beep. The beep is your signal to give a command. NOTE: If you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the VR hard-key, listen for the beep, and say your command. Pressing the VR hard-key while the system is speaking is known as “barging in.
PAGE 126
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Commands The Voice Recognition system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the Volume 1. Start a dialogue by pressing the VR hard-key. 2. Say a command (e.g., “Help”). 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the Voice Recognition system is speaking.
PAGE 127
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Radio FM To switch to the FM band say “FM” or “Radio FM”.
PAGE 128
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memo To switch to the voice recorder mode say “Memo”. In this mode, you may say the following commands: • “New Memo” (to record a new memo) — During the recording you may press the VR hard-key to stop recording.
PAGE 129
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 System Setup To switch to system setup say “Setup”. In this mode, you may say the following commands: • “Language English” • “Language French” • “Language Spanish” • “Tutorial” • “Voice Training” NOTE: Keep in mind that you have to press the VR hard-key first and wait for the beep before speaking the “Barge In” commands.
PAGE 130
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Power Seats The power seat switch is located on the outboard side of the seat near the floor. Use this switch to move the driver’s seat up or down, forward or rearward or to recline the seat. The passenger’s seat will move up or down, forward or rearward.
PAGE 131
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 WARNING! The recliner control is located on the outboard side of the seat. Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. 3 CAUTION! Do not place any article under a power seat as it may cause damage to the seat controls.
PAGE 132
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. Lumbar Support This feature allows you to increase or decrease the amount of lumbar support. Turn the control lever forward to increase and rearward to decrease the desired amount of lumbar support.
PAGE 133
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 upward on the head restraint. To lower it, depress the button on the post guide and push downward on the head restraint. Heated Seats — If Equipped This feature heats the front driver and passenger seats. The controls for each front seat are located near the bottom center of the instrument panel.
PAGE 134
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE On vehicles equipped with rear heated seats, the seats closest to the doors are heated. The controls for these seats are located on the rear of the center console. After turning ON the ignition, Press the switch once to select High level heating. Press the switch a second time to select Low level heating. Press the switch a third time to shut Off the heating elements. Amber indicators in the switch indicate the level of heat in use.
PAGE 135
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods. • Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat.
PAGE 136
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. • The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion.
PAGE 137
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 2. Adjust all memory profile settings to desired preferences (i.e., seat, side mirror, adjustable pedals [if equipped], power tilt and telescopic steering column [if equipped], and radio station presets). 3. Press and release the SET (S) button on the memory switch. 4. Within five seconds, press and release the memory button 1 or 2. The Electronic Vehicle Information Center (EVIC) (if equipped) will display which memory position has been set.
PAGE 138
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Recall Memory with Remote Key Unlock feature can be enabled through the EVIC (if equipped). Refer to “Personal Settings (Customer-Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4. Linking and Unlinking the Remote Keyless Entry (RKE) Transmitter to the Memory Feature Your RKE transmitters can be programmed to recall one of two pre-programmed memory profiles by pressing the UNLOCK button on the RKE transmitter.
PAGE 139
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 To recall the memory settings for driver one, press MEMORY button number 1 on the driver’s door or the UNLOCK button on the RKE transmitter linked to memory position 1. To recall the memory setting for driver two, press MEMORY button number 2 on the driver’s door or the UNLOCK button on the RKE transmitter linked to memory position 2. A recall can be cancelled by pressing any of the MEMORY buttons (S, 1, or 2) on the driver’s door during a recall.
PAGE 140
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE between 0.9 in and 2.7 in (22.7 mm and 67.7 mm) forward of the rear stop. The seat will return to its previously set position when you insert the key into the ignition switch and turn it out of the LOCK position. TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood. 1. Pull the hood release lever located under the left side of the instrument panel.
PAGE 141
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 2. Move to the outside of the vehicle and push the safety catch to the left. The safety catch is located under the center front edge of the hood. To prevent possible damage, do not slam the hood to close it. Lower the hood, until it is open approximately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
PAGE 142
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE operation of the headlights, parking lights, instrument panel lights, instrument panel light dimming, interior lights and fog lights. Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation. Turn it to the second detent for headlight, parking light and instrument panel light operation.
PAGE 143
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Headlights On with Wipers (Available with Auto Headlights Only) When this feature is active, the headlights will turn on approximately 10 seconds after the wipers are turned on if the headlight switch is placed in the AUTO position. In addition, the headlights will turn off when the wipers are turned off if they were turned on by this feature.
PAGE 144
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate Perform either of the following steps to deactivate the SmartBeam system. 1. Pull the multifunction lever toward you to switch the headlights from the high beam to the low beam position. 2. Rotate the headlight switch clockwise from the AUTO (A) to the ON position. NOTE: Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle).
PAGE 145
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 The headlight delay time is programmable on vehicles equipped with the EVIC. Refer to “Delay Turning Headlights Off,” under “Personal Settings (CustomerProgrammable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4. Daytime Running Lights — If Equipped The high beam headlights will come on as Daytime Running Lights whenever the ignition switch is ON, the headlights are off and the parking brake is off.
PAGE 146
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Multifunction Lever The multifunction lever controls the operation of the turn signals, headlight beam selection and passing lights. The multifunction lever is located on the left side of the steering column. Turn Signals Move the multifunction lever up or down and the corresponding turn signal indicator in the instrument cluster flashes to show proper operation of the front and rear turn signal lights.
PAGE 147
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 NOTE: A “Turn Signal On” message will appear in the EVIC (if equipped) and a continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on. the UNLOCK button on the Remote Keyless Entry (RKE) transmitter is pressed, or when the dimmer control is turned fully upward, past the second detent. High Beam/Low Beam Select Switch Push the multifunction lever away from you to switch the headlights to high beam.
PAGE 148
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights The interior lights come on when a door is opened. To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position. This will occur if the interior lights were switched on manually or are on because a door is open. This includes the glove box light, but not the trunk light. To restore interior light operation, either turn the ignition switch ON or cycle the light switch.
PAGE 149
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 WINDSHIELD WIPERS AND WASHERS The multifunction lever operates the windshield wipers and washer when the ignition switch is in the ON position. The multifunction lever is located on the left side of the steering column. Rotate the end of the multifunction lever to the first detent, past the intermittent settings for low speed wiper operation, or to the second detent past the intermittent settings for high speed wiper operation.
PAGE 150
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE regulate the wipe interval from a minimum of one cycle every second to a maximum of approximately 23 seconds between cycles. WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.
PAGE 151
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 The Headlights On with Wipers feature can be turned on or off through the Electronic Vehicle Information Center (EVIC) (if equipped). Refer to ”Headlights On with Wipers,” under “Personal Settings (CustomerProgrammable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4. Rain Sensing Wipers — If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver.
PAGE 152
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The rain sensing system has protective features for the wiper blades and arms.
PAGE 153
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 To unlock the steering column, pull the control handle outward. To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in position, push the control handle inward until fully engaged.
PAGE 154
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To tilt the steering column, move the lever up or down as desired. To lengthen or shorten the steering column, pull the lever toward you or push the lever away from you as desired. NOTE: For vehicles equipped with Driver Memory Seat, you can use your Remote Keyless Entry (RKE) transmitter or the memory switch on the driver’s door trim panel to return the tilt/telescopic steering column to pre-programmed positions. Refer to “Driver Memory Seat” in this section.
PAGE 155
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control is on. One of the following messages will display in the Electronic Vehicle Information Center (EVIC) (if equipped) if a pedal adjustment is attempted when the system is locked out: “Adjustable Pedal Disabled — Cruise Control Engaged” or “Adjustable Pedal Disabled — Vehicle In Reverse.
PAGE 156
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. ELECTRONIC SPEED CONTROL When engaged, Electronic Speed Control takes over the accelerator operation at speeds greater than 25 mph (40 km/h).
PAGE 157
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 To Activate Push and release the ON/OFF button located on the end of the Electronic Speed Control lever. The indicator light in the instrument cluster will illuminate to show that the speed control system is on. To turn the system off, push and release the ON/OFF button again. The system and the indicator light will turn off. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous.
PAGE 158
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate The system will disable Electronic Speed Control without erasing the memory if you: • Softly tap the brake pedal, • Depress the brake pedal, or • Pull the Electronic Speed Control lever toward you to CANCEL. Pushing and releasing the ON/OFF button or turning off the ignition erases the set speed from memory.
PAGE 159
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 Tapping the Electronic Speed Control lever to SET DECEL once will result in a 1 mph (1.6 km/h) speed decrease. Each time the Electronic Speed Control lever is tapped, speed decreases. To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control on Hills NOTE: The Electronic Speed Control system maintains speed up and down hills.
PAGE 160
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ACC will allow you to keep cruise control engaged in light to moderate traffic conditions without the constant need to reset your cruise control. ACC utilizes an infrared sensor designed to detect a vehicle directly ahead of you. NOTE: • If the sensor does not detect a vehicle ahead of you, ACC will maintain a fixed set speed.
PAGE 161
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 WARNING! (Continued) • Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions. • Does not predict the lane curvature or the movement of preceding vehicles and will not compensate for such changes. • Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings.
PAGE 162
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Cruise Control system has two control modes. • Adaptive cruise control mode for maintaining an appropriate distance between vehicles. Adaptive Cruise Control (ACC) Operation The speed control lever (located on the right side of the steering wheel) operates the ACC system. • Normal (fixed speed) cruise control mode for cruising at a constant preset speed. For additional information, refer to “Normal (Fixed Speed) Cruise Control Mode” in this section.
PAGE 163
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Activating Adaptive Cruise Control (ACC) You can only activate ACC if the vehicle speed is above 25 mph (40 km/h). When the system is turned on and in the READY state, the Electronic Vehicle Information Center (EVIC) displays “ACC READY.” When the system is OFF, the EVIC displays “CRUISE OFF.” NOTE: You cannot enable ACC under the following conditions: • When you apply the brakes. • When the parking brake is set.
PAGE 164
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To turn the system OFF, push and release the ON/OFF/ MODE button again. At this time, the system will turn off and the EVIC will display “CRUISE OFF.” WARNING! Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it.
PAGE 165
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 • The system will not be controlling the distance between your vehicle and the vehicle ahead. The vehicle speed will only be determined by the position of the accelerator pedal. • You softly tap the brake pedal. • You depress the brake pedal. • You pull the speed control lever toward you to CANCEL. • The Electronic Stability Program/Traction Control System (ESP/TCS) activates.
PAGE 166
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Turn Off The system will turn off and erase the set speed in memory if: • You push and release the ON/OFF/MODE button. • You turn off the ignition. • You switch off ESP. To Resume Speed Push the lever upward (RESUME/ACCEL) and release. Then remove your foot from the accelerator pedal. The EVIC will display the last set speed. WARNING! The Resume function should only be used if traffic and road conditions permit.
PAGE 167
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Tapping the lever up once will result in a 1 mph (1 km/h) increase in set speed. Each subsequent tap of the lever results in an increase of 1 mph (1 km/h). While ACC is set, the set speed can be decreased by pushing and holding the lever down (SET/DECEL). If the lever is continually held, the set speed will continue to decrease in 5 mph (10 km/h) increments until the lever is released. The decrease in set speed is reflected in the EVIC display.
PAGE 168
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Setting the Following Distance in ACC The specified following distance for ACC can be set by varying the distance setting between long, medium, and short. Using this distance setting and the vehicle speed, ACC calculates and sets the distance to the vehicle ahead. This distance setting displays in the EVIC. To change the distance setting, push the lever away from you (DISTANCE) and release.
PAGE 169
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 • The vehicle ahead slows to a speed below 15 mph (24 km/h) and the system automatically disengages itself. braking capacity. When this occurs, you should immediately apply the brakes as needed to maintain a safe distance from the vehicle ahead. • The distance setting is changed. • The system disengages. (Refer to the information on ACC Activation).
PAGE 170
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adaptive Cruise Control (ACC) Menu The EVIC displays the current ACC system settings. The EVIC is located in the upper part of the instrument cluster between the speedometer and the tachometer. The information it displays depends on ACC system status. Press the MENU button (located on the steering wheel) repeatedly until one of the following displays in the EVIC: Menu Button CRUISE OFF − When ACC is deactivated, the display will read “CRUISE OFF.
PAGE 171
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 ACC READY ACC SET − When ACC is activated, the display will read “ACC READY.” − When ACC is set, the set speed will display. 3 1 — Sensed Vehicle Indicator 2 — Set Speed 3 — Your Vehicle 4 — Following Distance Setting: Three Bars = Long; Two Bars = Medium; One Bar = Short.
PAGE 172
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The set speed will continue to display in place of the odometer reading when changing the EVIC display while ACC is set.
PAGE 173
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Display Warnings and Maintenance ACC Blinded Warning The ACC Blinded Warning will display when conditions temporarily limit system performance. This most often occurs at times of poor visibility, such as in snow, fog, heavy rain, or when driving into direct sunlight (sunrise or sunset). The ACC system may also become temporarily blinded due to obstructions, such as dirt or ice. In these cases, the EVIC will display “ACC Blinded” and the system will deactivate.
PAGE 174
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If weather conditions are not a factor, the driver should examine the sensor. It may require cleaning or removal of an obstruction. The sensor is located behind the grille, slightly offset from the center of the grille. • Always keep the sensor clean. Carefully wipe the sensor lens with a soft cloth. Be cautious not to damage the sensor lens. • Do not remove any screws from the sensor or the sensor mount.
PAGE 175
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 NOTE: Installing a vehicle front-end protector or an aftermarket grille or modifying the grille is not recommended. Doing so may block the sensor and inhibit ACC operation. ACC Unavailable Warning If the system turns off, and the EVIC displays ⬙ACC UNAVAILABLE,⬙ there may be a temporary malfunction that limits ACC functionality. Although the vehicle is still drivable under normal conditions, ACC will be temporarily unavailable.
PAGE 176
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Precautions While Driving with ACC In certain driving situations, ACC may have detection issues. In these cases, ACC may brake late or unexpectedly. The driver needs to stay alert and may need to intervene. Adding a Trailer Hitch The weight of a trailer hitch may affect the performance of ACC. If there is a noticeable change in performance following the installation of a hitch, such as reduced detection range, please see your authorized dealer for service.
PAGE 177
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 Using ACC on Hills When driving on hills, ACC may not detect a vehicle in your lane. Depending on the speed, vehicle load, traffic conditions, and the steepness of the hills, ACC performance may be limited. ACC may occasionally provide braking and/or a driver alert that you consider unnecessary. This may be the system’s response to signs, guardrails, and other stationary objects in a curve. This may also occur at the base of dramatic hills.
PAGE 178
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lane Changing ACC will not detect a vehicle until it is completely in the lane in which you are traveling. In the illustration shown, ACC has not yet detected the vehicle changing lanes and it will not until it may be too late to take action. ACC will not detect a vehicle until it is completely in the lane. There will not be sufficient distance to the lane-changing vehicle. Always be attentive and ready to apply the brakes if necessary.
PAGE 179
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 3 Stationary Objects and Vehicles ACC does not react to stationary objects and stationary vehicles. For example, ACC will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane. Always be attentive and ready to apply the brakes if necessary. General Information CLASS 1 LASER PRODUCT Classification Specifications: 21 C.F.R part 1040.10 & 1040.
PAGE 180
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Normal (Fixed Speed) Cruise Control Mode In addition to adaptive cruise control mode, a normal (fixed speed) cruise control mode is available for cruising at fixed speeds. The Normal cruise control mode is designed to maintain a set cruising speed without requiring the driver to operate the accelerator. Cruise control can only be operated if the vehicle speed is above 25 mph (40 km/h).
PAGE 181
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 To Vary the Speed Setting There are two ways to change the set speed: • The Electronic Stability Program/Traction Control System (ESP/TCS) activates. • Use the accelerator pedal to adjust the vehicle to the desired speed and push the lever down (“SET/ DECEL”). To Resume Push the lever up and release (“RESUME/ACCEL”) and then remove your foot from the accelerator pedal. The EVIC will display the last set speed.
PAGE 182
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR PARK ASSIST SYSTEM The Rear Park Assist system is a driver aid that senses for obstacles behind the vehicle. Refer to the Warnings, Cautions, and Notes in this section for system limitations and usage recommendations. The system uses four sensors located in the rear bumper to scan for obstacles up to 79 in (200 cm) away from the rear bumper fascia.
PAGE 183
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 The warning display contains two sets of yellow and red indicators, one set to warn of obstacles behind the left rear of the vehicle and the other set to warn of obstacles behind the right rear of the vehicle. The driver can view the indicators either through the rearview mirror or by looking at the display above the rear window.
PAGE 184
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Rear Park Assist system will MUTE the radio, if on, when the system is sounding an audio tone. WARNING! • Drivers must be careful when backing up even when using the Rear Park Assist system. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings.
PAGE 185
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 CAUTION! • The Rear Park Assist system is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using the Rear Park Assist system to be able to stop in time when the obstacle is detected.
PAGE 186
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE The overhead console contains courtesy/reading lights, an optional universal garage door opener (HomeLink威), storage for sunglasses, and an optional power sunroof switch. Courtesy/Reading Lights At the forward end of the console are two courtesy/ reading lights. Press the lens to turn on the light. Press it a second time to turn off the light.
PAGE 187
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 GARAGE DOOR OPENER — IF EQUIPPED HomeLink威 replaces up to three remote controls (handheld transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLink威 unit operates off your vehicle’s battery. 3 The HomeLink威 buttons are located in the overhead console, and contain one, two, or three dots/lines designating the different HomeLink威 channels.
PAGE 188
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features.
PAGE 189
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) from the HomeLink威 buttons while keeping the EVIC display in view. NOTE: Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section. For optimal training, point the battery end of the handheld transmitter away from the HomeLink威. 4. Press and hold the just-trained HomeLink威 button.
PAGE 190
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door). 6. Firmly press and release the “learn” or “training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7.
PAGE 191
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner.
PAGE 192
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming A Single HomeLink姞 Button To reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink威 button for 20 seconds until the EVIC display states “CHANNEL # TRAINING.” Do not release the button. 3. Without releasing the button, proceed with Programming HomeLink威 Step 2 and follow all remaining steps.
PAGE 193
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. 1. This device may not cause harmful interference 3 2.
PAGE 194
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
PAGE 195
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 sunroof will automatically retract. Remove the obstruction if this occurs. Next, press the switch forward and release to Express Close. Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing, press the switch forward and hold for two seconds after the reversal occurs.
PAGE 196
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed. Ignition Off Operation For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power sunroof switch will remain active for 10 minutes after the ignition switch is turned OFF. Opening either front door will cancel this feature.
PAGE 197
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 NOTE: If desired, the power outlet next to the ash receiver tray (if equipped) can be converted by your authorized dealer to provide power with the ignition switch in the LOCK position. The center console outlet is powered directly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or prevent engine starting.
PAGE 198
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine Off CAUTION! (Continued) CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.
PAGE 199
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 CUPHOLDERS Front Seat Cupholders The cupholders are located in the forward edge of the center console. Rear Seat Cupholders The rear seat cupholders are located in the center armrest between the rear seats. The cupholders are positioned forward in the armrest and side-by-side to provide convenient access to beverage cans or bottles while maintaining a resting place for the rear occupants elbows.
PAGE 200
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE Console Features The center console contains two shift bezel cubby bins with rubber mats for holding small items. For vehicles not equipped with navigation radio, the console also contains an extra storage bin located below the climate control, which holds up to four CD jewel cases. Without Vehicle Entertainment System (VES)威 Two separate storage compartments are also located underneath the armrest.
PAGE 201
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 The top compartment holds small items, such as a pen and note pad, while the larger bottom compartment will hold CDs and alike. The bottom compartment also contains a 12-Volt power outlet and a molded-in coin holder (designed to hold various size coins). A slot in the left and right side of the top compartment provides clearance for power cords to pass conveniently out of the bin with the lid closed.
PAGE 202
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) WARNING! • Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. • Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or become a dangerous projectile in a sudden stop or collision. • Be certain that the seatback is securely locked into position.
PAGE 203
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 WARNING! (Continued) • To help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts. CARGO AREA FEATURES Trunk Mat — If Equipped A reversible trunk mat covers the bottom of the cargo area. The rubber side of the mat is used to protect the interior of the trunk from mud, snow, and debris.
PAGE 204
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • To avoid damaging the electrical conductors of the rear window defroster, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • Labels can be peeled off after soaking with warm water. LOAD LEVELING SYSTEM — IF EQUIPPED The automatic load leveling system will provide a levelriding vehicle under most passenger and cargo loading conditions.
PAGE 205
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 207 䡵 Instrument Cluster — Base . . . . . . . . . . . . . . . 208 䡵 Instrument Cluster — Premium . . . . . . . . . . . 209 䡵 Instrument Cluster Descriptions . . . . . . . . . . . 210 䡵 Electronic Vehicle Information Center (EVIC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 221 ▫ Electronic Vehicle Information Center (EVIC) Displays . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 206
204 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Sales Code REQ — AM/FM Stereo Radio And 6–Disc CD/DVD Changer (MP3/WMA AUX Jack) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242 ▫ Operating Instructions — Hands-Free Communication (UConnect威) — If Equipped . . . . . . . . . . . . . . . . . . . . . . 258 ▫ Operating Instructions - Radio Mode . . . . . . 243 ▫ Clock Setting Procedure . . . . . . . . . . . . . . .
PAGE 207
UNDERSTANDING YOUR INSTRUMENT PANEL 205 ▫ Operation Instructions — CD Mode For CD And MP3 Audio Play . . . . . . . . . . . . . . . . . 276 ▫ System Activation . . . . . . . . . . . . . . . . . . . . 287 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . 278 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) . . . . . . . . . 287 ▫ List Button (CD Mode For MP3 Play) . . . . . . 280 ▫ Selecting Satellite Mode . . . . . . . . . . . . . . . . 288 ▫ Info Button (CD Mode For MP3 Play) . .
PAGE 208
206 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Sirius Backseat TV™ — If Equipped . . . . . . . . 293 䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 298 䡵 Video Entertainment System (VES)™ — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 293 ▫ Manual Air Conditioning And Heating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298 䡵 Remote Sound System Controls — If Equipped . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 209
UNDERSTANDING YOUR INSTRUMENT PANEL 207 INSTRUMENT PANEL FEATURES 4 1 - Air Outlet 2 - Instrument Cluster 3 - Hazard Switch 4 - Analog Clock 5 - Electronic Stability Program OFF Button* / Traction Control System OFF Button* 6 - Glove Compartment 7 - Radio 8 - Climate Control 9 - Heated Seat Switch* 10 - Power Outlet 11 - Ash Tray* 12 - Storage Compartment* 13 - Ignition Switch 14 - Hood Release 15 - Trunk Release Switch 16 - Headlight Switch * If Equipped
PAGE 210
208 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — BASE
PAGE 211
UNDERSTANDING YOUR INSTRUMENT PANEL 209 INSTRUMENT CLUSTER — PREMIUM 4
PAGE 212
210 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Electronic Speed Control / Adaptive Cruise Control (ACC) Indicator Light — If Equipped This light will turn on when the electronic speed control or Adaptive Cruise Control (ACC) is ON. 2. Low Fuel Indicator Light This light will turn on and a single chime will sound when the fuel level drops to 1/8 tank. 3. Front Fog Light Indicator — If Equipped This light will turn on when the front fog lights are ON. 4.
PAGE 213
UNDERSTANDING YOUR INSTRUMENT PANEL 211 Rear Wheel Drive (RWD) / All Wheel Drive (AWD) Displays (Base Cluster) On vehicles equipped with a Base Instrument Cluster, the odometer will display “2drivE” when the vehicle is in Rear Wheel Drive (RWD), and “4drivE” when All Wheel Drive (AWD) is activated. If the odometer displays the “tCASE” warning message after engine start up, or during driving, the AWD system is not functioning properly and service is required.
PAGE 214
212 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure. On vehicles equipped with a Premium Instrument Cluster, this display shows the Electronic Vehicle Information Center (EVIC) messages when the appropriate conditions exist. Lo tirE When the appropriate condition exists the odometer display will toggle between Lo and tirE for three cycles.
PAGE 215
UNDERSTANDING YOUR INSTRUMENT PANEL 213 9. Anti-Lock Brake (ABS) Light — If Equipped This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS Light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required.
PAGE 216
214 UNDERSTANDING YOUR INSTRUMENT PANEL 12. Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir.
PAGE 217
UNDERSTANDING YOUR INSTRUMENT PANEL 215 WARNING! Driving a vehicle with the brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately. Vehicles equipped with the Anti-Lock Brake System (ABS), are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.
PAGE 218
216 UNDERSTANDING YOUR INSTRUMENT PANEL or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H,” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.
PAGE 219
UNDERSTANDING YOUR INSTRUMENT PANEL 217 Trip Odometer Button — Premium Cluster Press this button to change the display from odometer to either of two trip odometer settings. The letter “A” or “B” will appear when in the trip odometer mode. Push in and hold the button for two seconds to reset the trip odometer to 0 miles (km). The odometer must be in TRIP mode to reset it. 16. High Beam Light This light will turn on when the high beam headlights are ON.
PAGE 220
218 UNDERSTANDING YOUR INSTRUMENT PANEL 21. Electronic Throttle Control (ETC) Light This light will turn on briefly as a bulb check when the ignition switch is turned ON. This light will also turn on while the engine is running if there is a problem with the Electronic Throttle Control (ETC) system. If the light comes on while the engine is running, safely bring the vehicle to a complete stop as soon as possible, place the shift lever in PARK, and cycle the ignition key. The light should turn off.
PAGE 221
UNDERSTANDING YOUR INSTRUMENT PANEL 219 possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
PAGE 222
220 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
PAGE 223
UNDERSTANDING YOUR INSTRUMENT PANEL 221 stays on through several of your typical driving cycles. In most situations, the vehicle will drive normally and will not require towing. ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED The MIL flashes to alert you to serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced as soon as possible if this occurs. 4 25.
PAGE 224
222 UNDERSTANDING YOUR INSTRUMENT PANEL This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel.
PAGE 225
UNDERSTANDING YOUR INSTRUMENT PANEL 223 Press the FUNCTION SELECT button to accept a selection. The FUNCTION SELECT button also functions as a remote sound system conFUNC- trol. Refer to “Remote Sound System Controls” TION in this section. SELECT Button Press the SCROLL button to scroll through Trip Functions, Navigation (if equipped), System Status Messages, and Personal Settings (CusSCROLL tomer Programmable Features). The SCROLL Button button also functions as a remote sound system control.
PAGE 226
224 UNDERSTANDING YOUR INSTRUMENT PANEL • Right Front Turn Signal Light Out (with a single chime) • Door(s) Ajar (with a single chime if vehicle is in motion) • Right Rear Turn Signal Light Out (with a single chime) • Trunk Ajar (with a single chime) • Key FOB Battery Low (with a single chime) • Low Washer Fluid (with a single chime) • Memory #1/#2 Profile Set • ECO – Multi-Displacement System (MDS) is activated (If Equipped with MDS) • Memory #1/#2 Profile Recall • Memory System Disabled – Vehicle
PAGE 227
UNDERSTANDING YOUR INSTRUMENT PANEL 225 • Cruise Off — When the Adaptive Cruise Control (ACC) system is turned off. Refer to “Adaptive Cruise Control (ACC)” in Section 3 (if equipped). • ACC Ready — When the ACC system is activated. Refer to “Adaptive Cruise Control (ACC)” in Section 3 (if equipped). • ACC Set — After setting the desired speed in the ACC system. Refer to “Adaptive Cruise Control (ACC)” in Section 3 (if equipped). • ACC Cancelled — To disable the ACC system.
PAGE 228
226 UNDERSTANDING YOUR INSTRUMENT PANEL • ACC Blinded — If the ACC system deactivates due to performance limiting conditions. Refer to “Adaptive Cruise Control (ACC)” in Section 3 (if equipped). • ACC Unavailable — If the ACC system turns off due to a temporary malfunction that limits functionality. Refer to “Adaptive Cruise Control (ACC)” in Section 3 (if equipped). • Service ACC — If the ACC system turns off due to an internal system fault that requires service from an authorized dealer.
PAGE 229
UNDERSTANDING YOUR INSTRUMENT PANEL 227 • Right Rear Low Pressure (with a single chime). Refer to information on “Tire Pressure” and “Tire Pressure Monitor” under “Starting And Operating.” • Check TPM System (with a single chime). Refer to information on “Tire Pressure Monitor” under “Starting And Operating.
PAGE 230
228 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Fully depress the accelerator pedal slowly three times within 10 seconds. Press the SCROLL button to cycle through all the Trip Computer functions. 3. Turn the ignition switch to the LOCK position. The Trip Functions mode displays the following information. NOTE: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary, repeat this procedure.
PAGE 231
UNDERSTANDING YOUR INSTRUMENT PANEL 229 MDS allows the engine to operate on four cylinders, which will vary depending on driving habits and vehicle usage. This feature allows you to monitor when the MDS switches off the fuel on four of the eight cylinders and it can be used to modify driving habits in order to increase the time in which the fuel saver mode is active.
PAGE 232
230 UNDERSTANDING YOUR INSTRUMENT PANEL • Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. DTE cannot be reset through the FUNCTION SELECT button.
PAGE 233
UNDERSTANDING YOUR INSTRUMENT PANEL 231 To Reset The Display Reset will only occur while a resettable function is being displayed. Press and release the FUNCTION SELECT button once to clear the resettable function being displayed. To reset all resettable functions, press and release the FUNCTION SELECT button a second time within three seconds of resetting the currently-displayed function. (Reset ALL will display during this three-second window).
PAGE 234
232 UNDERSTANDING YOUR INSTRUMENT PANEL When the vehicle automatically transitions from AWD to RWD the EVIC will display the following message for five seconds. Keyless Go Display — If Equipped When the ENGINE START/STOP button is pressed to change ignition states, the Keyless Go icon momentarily appears in the EVIC display showing the new ignition state.
PAGE 235
UNDERSTANDING YOUR INSTRUMENT PANEL 233 The round symbol in the middle rotates to point at the new ignition state. If desired, the ignition state graphic can be set to be constantly visible by pressing the EVIC MENU button until the display appears. NOTE: Under certain conditions, the display may be superseded by another display of higher priority. But when the ignition state is changed, the display always re-appears. Compass Display The compass readings indicate the direction the vehicle is facing.
PAGE 236
234 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Press and release the FUNCTION SELECT button to start the calibration. The message “CAL” will display in the EVIC. module is located, and it can cause interference with the compass sensor, and it may give false readings. 5. Complete one or more 360 degree turns (in an area free from large metal or metallic objects) until the “CAL” message turns off. The compass will now function normally.
PAGE 237
UNDERSTANDING YOUR INSTRUMENT PANEL 235 3. Press the SCROLL button until “Compass Variance” message and the last variance zone number displays in the EVIC. 4. Press and release FUNCTION SELECT button until the proper variance zone is selected according to the map. 5. Press and release the COMPASS button to exit. Driver-Selectable Surround Sound (DSS) – If Equipped Press and release the MENU button until “Surround Sound” displays in the EVIC. The EVIC provides information on the current surround mode.
PAGE 238
236 UNDERSTANDING YOUR INSTRUMENT PANEL top of the screen, followed by an arrow to indicate the direction to turn the vehicle, and a count down to indicate the distance to the turn. NOTE: Refer to your “Navigation User’s Manual” for detailed operating instructions. Personal Settings (Customer-Programmable Features) Personal Settings allows the driver to set and recall features when the transmission is in PARK. Press and release the MENU button until Personal Settings displays in the EVIC.
PAGE 239
UNDERSTANDING YOUR INSTRUMENT PANEL 237 “Remote Key Unlock” When Driver Door 1st Press is selected, only the driver’s door will unlock on the first press of the Remote Keyless Entry (RKE) transmitter UNLOCK button. When Driver Door 1st Press is selected, you must press the RKE transmitter UNLOCK button twice to unlock the passenger’s doors. When All Doors 1st Press is selected, all of the doors will unlock on the first press of the RKE transmitter UNLOCK button.
PAGE 240
238 UNDERSTANDING YOUR INSTRUMENT PANEL “Sound Horn with Remote Key Lock” When ON is selected, a short horn sound will occur when the RKE LOCK button is pressed. This feature may be selected with or without the flash lights on lock/unlock feature. To make your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears.
PAGE 241
UNDERSTANDING YOUR INSTRUMENT PANEL 239 “Headlights On with Wipers” (Available with Auto Headlights Only) When ON is selected, and the HEADLIGHT switch is in the AUTO position, the headlights will turn on approximately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on by this feature. To make your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears.
PAGE 242
240 UNDERSTANDING YOUR INSTRUMENT PANEL “Delay Power Off to Accessories Until Exit” When this feature is selected, the power WINDOW switches, radio, hands-free system (if equipped), DVD video system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 60 minutes after the ignition switch is turned OFF. Opening a vehicle door will cancel this feature. To make your selection, press and release the FUNCTION SELECT button until “Off,” “45 sec.,” “5 min.,” “10 min.
PAGE 243
UNDERSTANDING YOUR INSTRUMENT PANEL 241 “Turn-by-Turn Navigation” — If Equipped When ON is selected, the turn-by-turn directions will appear in the display as the vehicle approaches a designated turn within a programmed route. To make your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears.
PAGE 244
242 UNDERSTANDING YOUR INSTRUMENT PANEL SETTING THE ANALOG CLOCK To set the analog clock at the top center of the instrument panel, press and hold the button until the setting is correct. SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate.
PAGE 245
UNDERSTANDING YOUR INSTRUMENT PANEL 243 Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
PAGE 246
244 UNDERSTANDING YOUR INSTRUMENT PANEL Phone Button (UConnect威 Hands-Free Phone) — If Equipped Press this button to operate the Hands-Free Phone (UConnect威) feature (if equipped). Refer to “Hands-Free Communication (UConnect威)” in Section 3. If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With UConnect” message will display on the radio screen. TIME Button Press the TIME button and the time of day will display.
PAGE 247
UNDERSTANDING YOUR INSTRUMENT PANEL 245 RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in AM, FM or Satellite (if equipped) frequencies. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones.
PAGE 248
246 UNDERSTANDING YOUR INSTRUMENT PANEL MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be selected. Many radio stations do not currently broadcast Music Type information.
PAGE 249
UNDERSTANDING YOUR INSTRUMENT PANEL 247 Program Type Sports Talk Top 40 Weather 16-Digit Character Display Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode.
PAGE 250
248 UNDERSTANDING YOUR INSTRUMENT PANEL • Audio Stream – Repeatedly pressing SELECT will switch to different audio languages (if supported on the disc) (if equipped). • VES™ CH1/CH2 - Allows the user to change the mode of either the IR1 or IR2, wireless headphones by pressing the AUDIO/SELECT button (if equipped). • Angle – Repeatedly pressing SELECT will change the viewing angle if supported by the DVD disc (if equipped). • Set Home Clock - Pressing the SELECT button allows you to set the clock.
PAGE 251
UNDERSTANDING YOUR INSTRUMENT PANEL 249 Enter the four-digit country code using the TUNE/ SCROLL control knob to scroll up and down to select the number and then push to select. Subtitles — If Equipped Selecting this item allows you to choose between subtitle Off or On. Audio Language — If Equipped Selecting this item allows you to choose a default audio language (effective only if the language is supported by the disc). You can select a language not listed by scrolling down and selecting ⬙other.
PAGE 252
250 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The user will have to set these defaults before loading a disc. If changes are made to these settings after a disc is loaded, changes will not be effective. Also, the defaults are effective only if the disc supports the customer-preferred settings. AM and FM Buttons Press the buttons to select AM or FM Modes. SET Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET button.
PAGE 253
UNDERSTANDING YOUR INSTRUMENT PANEL 251 Operation Instructions - (DISC MODE for CD and MP3/WMA Audio Play, DVD-VIDEO) The radio DVD player and many DVD discs are coded by geographic region. These region codes must match in order for the disc to play. If the region code for the DVD disc does not match the region code for the radio DVD player, it will not play the disc. Customers may take their vehicle to an authorized dealer to change the region code of the player a maximum of five times.
PAGE 254
252 UNDERSTANDING YOUR INSTRUMENT PANEL Eject Button — Ejecting Compact Disc(s) Press the EJECT button and the pushbutton with the corresponding number (1-6) where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. Press and hold the EJECT button for five seconds and all CDs will be ejected from the radio. The disc can be ejected with the radio and ignition OFF.
PAGE 255
UNDERSTANDING YOUR INSTRUMENT PANEL 253 Notes On Playing MP3/WMA Files The radio can play MP3/WMA files; however, acceptable MP3/WMA file recording media and formats are limited. When writing MP3/WMA files, pay attention to the following restrictions.
PAGE 256
254 UNDERSTANDING YOUR INSTRUMENT PANEL If a disc contains multi-formats, such as CD audio and MP3/WMA tracks, the radio will only play the MP3/ WMA tracks on that disc. MPEG Specification Supported MP3/WMA File Formats The radio will recognize only files with the *.MP3/WMA extension as MP3/WMA files. Non-MP3/WMA files named with the *.MP3/WMA extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3/WMA and will not play the file. MPEG-1 Audio Layer 3 48, 44.
PAGE 257
UNDERSTANDING YOUR INSTRUMENT PANEL 255 Playback of MP3/WMA Files When a medium containing MP3/WMA data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3/WMA files.
PAGE 258
256 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display. SCAN Button (Auxiliary Mode) No function. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3/WMA player, cassette player, or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
PAGE 259
UNDERSTANDING YOUR INSTRUMENT PANEL 257 Operating Instructions — Voice Recognition System (VR) (If Equipped) For the radio, refer to “Voice Recognition System (VR)” in Section 3. Dolby威 Manufactured under license from Dolby威 Laboratories. ⬙Dolby威⬙ and the double-D symbol are trademarks of Dolby威 Laboratories. For UConnect威 “Voice Recognition System (VR),” refer to “Hands-Free Communication (UConnect威)” in Section 3.
PAGE 260
258 UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM/CD/DVD MULTIMEDIA SYSTEM RADIO (RER/REN) – IF EQUIPPED NOTE: The sales code is located on the lower right side of the unit’s faceplate. The REN and RER Multimedia systems contain a radio, CD/DVD player, USB port, and a 30-gigabyte hard drive (HDD). Sirius Satellite Radio is optional. The 6.5 in (16.5 cm) touch screen allows for easy menu selection. The RER radio also contains a Global Positioning System (GPS)-based Navigation system.
PAGE 261
UNDERSTANDING YOUR INSTRUMENT PANEL 259 To Manually Set the Clock — RER/REN 1. Turn on the multimedia system. 2. Touch the screen where the time is displayed. 3. Touch the screen where “User Clock” is displayed. The clock setting menu will appear on the screen. 4. To move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is displayed. To move the hour backward, touch the screen where the word “Hour” with the arrow pointing downward is displayed. 5.
PAGE 262
260 UNDERSTANDING YOUR INSTRUMENT PANEL Show Time if Radio is Off When selected, this feature will display the time of day on the touch screen when the multimedia system is turned off. Proceed as follows to change the current setting: Changing the Time Zone 1. Turn on the multimedia system. 3. Touch the screen where the words “Set Time Zone” are displayed. The time zone selection menu will appear on the screen. 2. Touch the screen where the time is displayed.
PAGE 263
UNDERSTANDING YOUR INSTRUMENT PANEL 261 SALES CODE RES — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the On/Volume control knob to turn on the radio. Push the On/Volume control knob a second time to turn off the radio.
PAGE 264
262 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. TIME Button Press the TIME button and the time of day will display.
PAGE 265
UNDERSTANDING YOUR INSTRUMENT PANEL 263 Setting the Tone, Balance, and Fade Push the rotary Tune/Scroll control knob and BASS will display. Turn the Tune/Scroll control knob to the right or left to increase or decrease the bass tones. Push the rotary Tune/Scroll control knob a fifth time and FADE will display. Turn the Tune/Scroll control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary Tune/Scroll control knob a second time and MID will display.
PAGE 266
264 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET/RND button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice.
PAGE 267
UNDERSTANDING YOUR INSTRUMENT PANEL 265 If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. CAUTION! • This CD player will accept 4-3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels.
PAGE 268
266 UNDERSTANDING YOUR INSTRUMENT PANEL the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD, MP3 modes. TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display. RW/FF Press the RW button to stop the CD at the beginning of the current CD track/title.
PAGE 269
UNDERSTANDING YOUR INSTRUMENT PANEL 267 Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file normally. UDF and Apple HFS formats are not supported.
PAGE 270
268 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
PAGE 271
UNDERSTANDING YOUR INSTRUMENT PANEL 269 Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
PAGE 272
270 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RES/RSC — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) AND SIRIUS RADIO NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the On/Volume control knob to turn on the radio. Push the On/Volume control knob a second time to turn off the radio.
PAGE 273
UNDERSTANDING YOUR INSTRUMENT PANEL 271 SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. Voice Recognition System (Radio) — If Equipped Refer to “Voice Recognition System (VR)” in Section 3.
PAGE 274
272 UNDERSTANDING YOUR INSTRUMENT PANEL 3. After adjusting the hours, press the right side Tune/ Scroll control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side Tune/Scroll control knob. Press the Tune/Scroll control knob to save time change. 5. To exit, press any button/knob or wait five seconds. The clock can also be set by pressing the SETUP button.
PAGE 275
UNDERSTANDING YOUR INSTRUMENT PANEL 273 Push the rotary Tune/Scroll control knob a second time and MID will display. Turn the Tune/Scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary Tune/Scroll control knob a third time and TREBLE will display. Turn the Tune/Scroll control knob to the right or left to increase or decrease the treble tones. Push the rotary Tune/Scroll control knob a fourth time and BALANCE will display.
PAGE 276
274 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Foreign Language Information Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues 16-Digit Character Display Language Inform Jazz News Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R&B Program Type Sports Talk Top 40 Weather 16-Digit Character Display Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is disp
PAGE 277
UNDERSTANDING YOUR INSTRUMENT PANEL 275 SETUP Button Pressing the SETUP button allows you to select between the following items: • Set Clock — Pressing the SELECT button will allow you to set the clock. Turn the Tune/Scroll control knob to adjust the hours and then press and turn the Tune/Scroll control knob to adjust the minutes. Press the Tune/Scroll control knob again to save changes. AM/FM Button Press the button to select either AM or FM mode.
PAGE 278
276 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions — CD MODE for CD and MP3 Audio Play NOTE: • The ignition switch must be in the ON or ACC position to operate the radio. • This radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable compact discs (CD-RW), compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks. Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up.
PAGE 279
UNDERSTANDING YOUR INSTRUMENT PANEL 277 EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the CD is not removed, the radio will reinsert the CD but will not play it. A disc can be ejected with the radio and ignition OFF. NOTE: Ejecting with ignition OFF is not allowed on convertible or soft-top models (if equipped). SEEK Button Press the right SEEK button for the next selection on the CD.
PAGE 280
278 UNDERSTANDING YOUR INSTRUMENT PANEL SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right SEEK button to move to the next randomly selected track. Press the SET/RND button a second time to stop Random Play.
PAGE 281
UNDERSTANDING YOUR INSTRUMENT PANEL 279 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙.⬙ and a threecharacter extension) • Level 2: 31 (including a separator ⬙.⬙ and a threecharacter extension) Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs.
PAGE 282
280 UNDERSTANDING YOUR INSTRUMENT PANEL ID3 Tag information for artist, song title, and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported. Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
PAGE 283
UNDERSTANDING YOUR INSTRUMENT PANEL 281 INFO Button (CD Mode for MP3 Play) Pressing the INFO button repeatedly will scroll through the following TAG information: Song Title, Artist, File Name, and Folder Name (if available). Press the INFO button once more to return to ⬙elapsed time⬙ priority mode. Press and hold the INFO button for three seconds or more and the radio will display song titles for each file. Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display.
PAGE 284
282 UNDERSTANDING YOUR INSTRUMENT PANEL UNIVERSAL CONSUMER INTERFACE (UCI) — IF EQUIPPED NOTE: This section is for sales code RES and REQ/ REL/RET radios only with UConnect威. For sales code RER, REN and REZ touch-screen radio UCI feature, refer to the separate RER, REN or REZ User’s Manual. UCI is available only if equipped as an option with these radios. This feature allows you to plug an iPod威 into the vehicle’s sound system through a 16–pin connector using the provided interface cable.
PAGE 285
UNDERSTANDING YOUR INSTRUMENT PANEL 283 NOTE: • You may have to remove the connector pin protection cap from the 16–pin connector port, prior to connecting the cable. • If the iPod威 battery is completely discharged, it may not communicate with the UCI system until a minimum charge is attained. Leaving the iPod威 connected to the UCI system may charge it to the required level.
PAGE 286
284 UNDERSTANDING YOUR INSTRUMENT PANEL • Turning it counterclockwise (backward) by one click, during the first two seconds of the track, will jump to the previous track in the list. Turning this button at any other time in the track, will jump to the beginning of the current track. jump to the previous track in the list, if you press this button at any other time in the track it will jump to the beginning of the track.
PAGE 287
UNDERSTANDING YOUR INSTRUMENT PANEL 285 During Scan mode you can also press the << SEEK and SEEK >> buttons to select the previous and next tracks. • RND button (available on sales code RES radio only): Pressing this button toggles between Shuffle ON and Shuffle OFF modes for the iPod威. If the RND icon is showing on the radio display, then the shuffle mode is ON. List Or Browse Mode During Play mode, pressing any of the buttons described below, takes you to List mode.
PAGE 288
286 UNDERSTANDING YOUR INSTRUMENT PANEL • Preset 5 - Audiobooks • Preset 6 – Podcasts • Pressing a PRESET button, will display the current list on the top line and the first item in that list on the second line. • To Exit List mode without selecting a track, press the same PRESET button again to go back to Play mode. • LIST button: The LIST button will display the top level menu of the iPod威. Turn the TUNE control knob to list the top-menu item you wish to select and press the TUNE control knob.
PAGE 289
UNDERSTANDING YOUR INSTRUMENT PANEL 287 SATELLITE RADIO — IF EQUIPPED (REN/REQ/RER/RES/REU RADIOS ONLY) Satellite radio uses direct satellite-to-receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius Satellite Radio. This service offers over 130 channels of music, sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios.
PAGE 290
288 UNDERSTANDING YOUR INSTRUMENT PANEL Sirius ID number will display. The Sirius ID number display will time out in two minutes. Press any button on the radio to exit this screen. ESN/SID Access With REN/RER Radios While in SAT mode, press the MENU button on the radio faceplate. Next, touch the SUBSCRIPTION tab on the touch screen. All the ESNs that apply to your vehicle will display. ESN/SID Access With REU Radio While in SAT mode, press the MENU button on the radio faceplate.
PAGE 291
UNDERSTANDING YOUR INSTRUMENT PANEL 289 • Dense tree coverage may interrupt reception in the form of short audio mutes. • Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage. Operating Instructions — Satellite Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. SEEK Buttons Press and release the SEEK buttons to search for the next channel in Satellite mode.
PAGE 292
290 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next channel in the direction of the arrows. TUNE Control (Rotary) Turn the rotary Tune/Scroll control knob clockwise to increase or counterclockwise to decrease the channel. MUSIC TYPE Button — Except REU Radio Pressing this button once will turn on the Music Type mode for five seconds.
PAGE 293
UNDERSTANDING YOUR INSTRUMENT PANEL 291 SETUP Button Pressing the SETUP button allows you to select the following items: • Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number. This number is used to activate, deactivate, or change the Sirius subscription. SET Button – To Set the Pushbutton Memory When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window.
PAGE 294
292 UNDERSTANDING YOUR INSTRUMENT PANEL KICKER姞 HIGH PERFORMANCE SOUND SYSTEM WITH DRIVER-SELECTABLE SURROUND (DSS) – IF EQUIPPED “Audio Surround” is optimized for front seat passengers for any audio source. This surround effect is available for audio from any source – AM/FM/CD/ Satellite Radio or AUX – and is activated through the Electronic Vehicle Information Center (EVIC). Refer to “Driver-Selectable Surround Sound (DSS)” under “Electronic Vehicle Information Center (EVIC)” in Section 4.
PAGE 295
UNDERSTANDING YOUR INSTRUMENT PANEL 293 SIRIUS BACKSEAT TV™ — IF EQUIPPED Satellite video uses direct satellite receiver broadcasting technology to provide streaming video. The subscription service provider is SIRIUS Satellite Radio. SIRIUS Backseat TV™ offers three video channels for family entertainment, directly from its satellites and broadcasting studios. • A diagonal 7 in (17.8 cm) Liquid Crystal Display (LCD) screen integrated into the center console armrest.
PAGE 296
294 UNDERSTANDING YOUR INSTRUMENT PANEL • The LCD screen swings up from the rear of the armrest to allow the rear seat passenger(s) to view the display. • The touch screen radio and DVD player controls allow front seat operation for easy setup in the case of younger rear seat passengers. • A battery-powered infrared remote control snaps into a molded compartment in the center console armrest upper storage bin.
PAGE 297
UNDERSTANDING YOUR INSTRUMENT PANEL 295 • Two wireless infrared headsets allow rear seat passengers to listen to the same or individual audio sources. Audio/Video RCA Jacks (AUX Jacks) on the rear of the center console enable the monitor to display video directly from a video camera, connect video games for display on the screen, or play music directly from an MP3 player.
PAGE 298
296 UNDERSTANDING YOUR INSTRUMENT PANEL The remote sound system controls are located on the surface of the steering wheel at the three and nine o’clock positions. Vehicles equipped with steering wheel-mounted buttons are also equipped with the Electronic Vehicle Information Center (EVIC). The EVIC features a driver-interactive display which is located in the instrument cluster. VOLUME Button The VOLUME button controls the sound level of the sound system.
PAGE 299
UNDERSTANDING YOUR INSTRUMENT PANEL 297 When the EVIC is in the Compass/Temp/ Audio screen, press the SCROLL button to seek up and down radio stations, tracks, chapters, SCROLL files, etc., depending on which radio is in the Button vehicle. CD/DVD MAINTENANCE To keep a CD/DVD in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3.
PAGE 300
298 UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS The air conditioning and heating system is designed to make you comfortable in all types of weather. Manual Air Conditioning and Heating System Blower Control The rotary knob on the left controls the blower. The control has an OFF position and four speed settings. The blower will remain on until the control is turned to the OFF position or the ignition is turned OFF.
PAGE 301
UNDERSTANDING YOUR INSTRUMENT PANEL 299 Temperature Control The rotary knob in the center controls air temperature. Rotate the control to the left for cooler air temperature and to the right for warmer air temperature. Rotating the control to the extreme left provides the coldest setting. Rotating the control to the extreme right provides the warmest setting. Mode Control The rotary knob on the right controls airflow distribution.
PAGE 302
300 UNDERSTANDING YOUR INSTRUMENT PANEL • Bi-Level Air flows through the outlets located in the instrument panel and through the outlets located on the floor. Air flows through the registers in the back of the center console to the rear seat passengers. These registers can be closed to partially block airflow. • Panel Air flows through the outlets located in the instrument panel. Air flows through the registers in the back of the center console to the rear seat passengers.
PAGE 303
UNDERSTANDING YOUR INSTRUMENT PANEL 301 Automatic Temperature Control — If Equipped Automatic Temperature Controls Automatic Operation The Infrared Dual-Zone Climate Control System automatically maintains the climate in the cabin of the vehicle at the comfort levels desired by the driver and passenger.
PAGE 304
302 UNDERSTANDING YOUR INSTRUMENT PANEL or HI AUTO. The LO AUTO position should be used for front seat occupants only. The HI AUTO position should be used when more airflow is desired, or when rear seat occupants are present. Then, dial in the temperature you would like the system to maintain by rotating the driver or passenger temperature control knob. Once the comfort level is selected, the system will maintain that level automatically using the heating system.
PAGE 305
UNDERSTANDING YOUR INSTRUMENT PANEL 303 NOTE: • The surface of the climate control panel and the top center of the instrument panel should be kept free of debris due to the location of the climate control sensors. Mud on the windshield may also cause poor operation of this system. • Extended use of recirculation may cause the windows to fog. If the interior of the windows begin to fog, press the recirculation button to return to outside air.
PAGE 306
304 UNDERSTANDING YOUR INSTRUMENT PANEL
PAGE 307
UNDERSTANDING YOUR INSTRUMENT PANEL 305 The operator can override the AUTO mode setting to change airflow distribution by rotating the mode control knob (on the right) to one of the following positions. • Defrost Air is directed to the windshield through the outlets at the base of the windshield. Air is also directed to the front door windows through the side window demister grilles. • Defrost/Floor Air flows through the front and rear floor outlets and the outlets at the base of the windshield.
PAGE 308
306 UNDERSTANDING YOUR INSTRUMENT PANEL conditioning. An indicator in the button illuminates when manual compressor operation is selected. NOTE: To control the air conditioning manually, the mode selector must be moved out of the AUTO position. • Recirculation Control This button can be used to block out smoke, odors, dust, high humidity, or if rapid cooling is desired. The Recirculation mode should only be used temporarily. An indicator in the button illuminates when the Recirculation mode is active.
PAGE 309
UNDERSTANDING YOUR INSTRUMENT PANEL 307 Winter Operation Use of the air Recirculation mode during Winter months is not recommended because it may cause window fogging. Vacation Storage Any time you store your vehicle or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.
PAGE 310
308 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions for Various Weather Conditions
PAGE 311
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 313 䡵 Automatic Transmission . . . . . . . . . . . . . . . . . 318 ▫ Automatic Transmission . . . . . . . . . . . . . . . 313 ▫ General Information . . . . . . . . . . . . . . . . . . 319 ▫ Keyless Go (If Equipped) . . . . . . . . . . . . . . . 314 ▫ Brake/Transmission Shift Interlock System . . 321 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . .
PAGE 312
310 STARTING AND OPERATING 䡵 All-Wheel Drive (AWD) — If Equipped . . . . . . 333 ▫ Anti-Lock Brake System (ABS) . . . . . . . . . . . 343 䡵 Driving On Slippery Surfaces . . . . . . . . . . . . . 334 ▫ Traction Control System (TCS) . . . . . . . . . . . 343 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . 334 ▫ Brake Assist System (BAS) . . . . . . . . . . . . . . 344 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . 334 ▫ Electronic Stability Program (ESP) . . . . . . .
PAGE 313
STARTING AND OPERATING 311 ▫ Tire Inflation Pressures . . . . . . . . . . . . . . . . 358 䡵 Tire Pressure Monitor System (TPMS) . . . . . . . 369 ▫ Tire Pressures For High Speed Operation . . . 359 ▫ Base System . . . . . . . . . . . . . . . . . . . . . . . . 371 ▫ Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . 360 ▫ Premium System — If Equipped . . . . . . . . . 374 ▫ Compact Spare Tire — If Equipped . . . . . . . 361 ▫ General Information . . . . . . . . . . . . . . . . . .
PAGE 314
312 STARTING AND OPERATING ▫ Carbon Monoxide Warnings . . . . . . . . . . . . 383 ▫ Common Towing Definitions . . . . . . . . . . . . 389 䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 384 ▫ Trailer Hitch Classification . . . . . . . . . . . . . . 392 ▫ Fuel Filler Cap (Gas Cap) . . . . . . . . . . . . . . 384 ▫ Trailer Towing Weights (Maximum Trailer Weight Ratings) . . . . . . . . . . . . . . . . . . . . . 393 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . .
PAGE 315
STARTING AND OPERATING 313 STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition.
PAGE 316
314 STARTING AND OPERATING CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly on the brake pedal.
PAGE 317
STARTING AND OPERATING 315 To reinstall the button, position it with its lettering oriented horizontal and readable. Gently insert the button into the receptacle by pressing on the center of the button. If the button slips in easily, it has been installed correctly. Press firmly on the center of the button to seat the button into the receptacle. Normal Starting The ENGINE START/STOP button should only be removed or inserted with the ignition in the OFF position.
PAGE 318
316 STARTING AND OPERATING Do not press the accelerator. Use the Fob with Integrated Key to briefly turn the ignition switch to the START position and release it as soon as the starter engages. The starter motor will continue to run, and it will disengage automatically when the engine is running. If the engine fails to start, the starter will disengage automatically in 10 seconds.
PAGE 319
STARTING AND OPERATING 317 WARNING! (Continued) • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle.
PAGE 320
318 STARTING AND OPERATING CAUTION! WARNING! To prevent damage to the starter, wait 10 to 15 seconds before trying again. Remember to disconnect the cord before driving. Damage to the 110-115 Volt electrical cord could cause electrocution. After Starting The idle speed is controlled automatically and it will decrease as the engine warms up. ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms the engine, and permits quicker starts in cold weather.
PAGE 321
STARTING AND OPERATING 319 CAUTION! (Continued) • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly on the brake pedal. WARNING! It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse.
PAGE 322
320 STARTING AND OPERATING NOTE: • After selecting any driving position, wait a moment to allow the gear to engage fully before accelerating, especially when the engine is cold. The shift lever is automatically locked while in the PARK position. To move the shift lever out of the PARK position, the brake pedal must be firmly depressed before the shift lock will release. • If there is a need to restart the engine, be sure to cycle the key to the LOCK position before restarting.
PAGE 323
STARTING AND OPERATING 321 WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the transmission into PARK, remove the key from the ignition, and apply the parking brake. Once the key is removed from the ignition, the transmission shift lever is locked in the PARK position, securing the vehicle against unwanted movement.
PAGE 324
322 STARTING AND OPERATING located to the right of the shift lever. The override access port is at the top of the bin to the right of the shift lever gate. Interlock Manual Override To activate the override, first insert the key into the ignition switch and turn it to the ON position. Then, press the pink-colored tab through the access port with a small flat blade screwdriver or alike. While pressing the override, move the shift lever out of the PARK position.
PAGE 325
STARTING AND OPERATING 323 4-Speed Automatic Transmission NOTE: Under extreme cold temperatures (-6°F (-21°C) and when in DRIVE, transmission operation may be briefly limited to only 2nd gear operation. Normal operation will resume once the transmission temperature has risen to a suitable level. Shifting from DRIVE to PARK or REVERSE should be done only after the accelerator pedal is released and the vehicle is stopped.
PAGE 326
324 STARTING AND OPERATING When parking on a flat surface, place the shift lever in the PARK position first, and then apply the parking brake. The following indicators should be used to ensure that you have engaged the shift lever in the PARK position: When parking on a hill, it is important to set the parking brake before placing the shift lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of park.
PAGE 327
STARTING AND OPERATING 325 NEUTRAL The engine may be started in this range. CAUTION! Coasting the vehicle or driving for any other reason with shift lever in NEUTRAL can result in transmission damage. WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have an accident.
PAGE 328
326 STARTING AND OPERATING “3” (Third) This range eliminates shifts into Overdrive. The transmission will operate normally in 1st, 2nd, and 3rd while in this range. The “3” position should also be used when descending steep grades to prevent brake system distress. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance and extend transmission life by reducing excessive shifting and heat buildup.
PAGE 329
STARTING AND OPERATING 327 NOTE: • The torque converter clutch will not engage until the transmission fluid and engine coolant is warm (usually after 1–3 miles [1.6–4.8 km] of driving). Because engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting into Overdrive when cold. This is considered a normal condition. Pulling the shift lever into the “3” position will show that the transmission is able to shift into and out of Overdrive.
PAGE 330
328 STARTING AND OPERATING NOTE: Even if the transmission can be reset, we recommend that you visit an authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur. If the transmission cannot be reset, authorized dealer service is required. 5-Speed Automatic Transmission Shifting from DRIVE to PARK or REVERSE should be done only after the accelerator pedal is released and the vehicle is stopped.
PAGE 331
STARTING AND OPERATING 329 When parking on a flat surface, place the shift lever in the PARK position first, and then apply the parking brake. The following indicators should be used to ensure that you have engaged the shift lever in the PARK position: When parking on a hill, it is important to set the parking brake before placing the shift lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of PARK.
PAGE 332
330 STARTING AND OPERATING NEUTRAL In NEUTRAL, no power is transmitted from the engine to the drive axle. When the brakes are released, the vehicle can be moved freely (pushed or towed). Do not engage NEUTRAL position while driving except to coast when the vehicle is in danger of skidding (e.g., on icy roads). The engine may be started in this range. Use this range for starting your vehicle if it is moving or being towed.
PAGE 333
STARTING AND OPERATING 331 under heavy loading conditions (in hilly terrain, traveling into strong head winds, or while towing heavy trailers, use the AutoStick威 mode and select the “3” range. brought to a stop. After the vehicle has stopped, PARK, REVERSE, and NEUTRAL will continue to operate. Second gear will operate in the DRIVE position. The Malfunction Indicator Light (MIL) may be illuminated.
PAGE 334
332 STARTING AND OPERATING NOTE: Even if the transmission can be reset, we recommend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur. Have the transmission checked at your authorized dealer as soon as possible. If the problem has been momentary, the transmission can be reset to regain all forward gears.
PAGE 335
STARTING AND OPERATING 333 You can shift in or out of the Autostick威 mode at any time without taking your foot off the accelerator pedal. If you choose the Overdrive mode, the transmission will operate automatically, shifting between the five available gears. When you wish to engage Autostick威, simply move the shift lever to the right or left (D+/D-) while in the DRIVE position. The transmission will remain in the current gear until an upshift or downshift is chosen.
PAGE 336
334 STARTING AND OPERATING CAUTION! WARNING! All wheels must have the same size and type tires. Unequal tire sizes must not be used. Unequal tire size may cause failure of the front differential and/or the transfer case. Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the rear wheels. You could lose control of the vehicle and possibly have an accident.
PAGE 337
STARTING AND OPERATING 335 2. Slow down if the road has standing water or puddles. 3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop. DRIVING THROUGH WATER Driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle.
PAGE 338
336 STARTING AND OPERATING Shallow Standing Water Although your vehicle is capable of driving through shallow standing water, consider the following Caution and Warning before doing so. CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle.
PAGE 339
STARTING AND OPERATING 337 WARNING! • Driving through standing water limits your vehicle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes.
PAGE 340
338 STARTING AND OPERATING WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer. No chemical flushes should be used in any power steering system; only the approved lubricant may be used.
PAGE 341
STARTING AND OPERATING 339 MULTI-DISPLACEMENT SYSTEM (MDS) — 5.7L ENGINE ONLY This feature offers improved fuel economy by shutting off four of the engine’s eight cylinders during light load and cruise conditions. The system is automatic with no driver inputs or additional driving skills required. NOTE: The MDS system may take some time to return to full functionality after a battery disconnect. PARKING BRAKE The parking brake should always be applied when the driver is not in the vehicle.
PAGE 342
340 STARTING AND OPERATING The foot operated parking brake is positioned below the lower left corner of the instrument panel. To apply the parking brake, push the parking brake pedal down and then remove your foot from the pedal. To release the parking brake, push down on the parking brake pedal and then release. The BRAKE light in the instrument cluster will turn on when the parking brake is applied and the ignition switch is ON. NOTE: This light only shows that the parking brake is applied.
PAGE 343
STARTING AND OPERATING 341 ANTI-LOCK BRAKE SYSTEM The Anti-Lock Brake System (ABS) provides increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up. ABS is activated during braking under certain road or stopping conditions. ABS-inducing conditions can include ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops.
PAGE 344
342 STARTING AND OPERATING WARNING! WARNING! (Continued) • The ABS contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals. • Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident.
PAGE 345
STARTING AND OPERATING 343 ELECTRONIC BRAKE CONTROL SYSTEM Your vehicle is equipped with an advanced electronic brake control system that include ABS (Anti-Lock Brake System), TCS (Traction Control System), BAS (Brake Assist System), and ESP (Electronic Stability Program). All four of these systems work together to enhance vehicle stability and control in various driving conditions.
PAGE 346
344 STARTING AND OPERATING Brake Assist System (BAS) This system complements the ABS by optimizing the vehicle braking capability during emergency brake maneuvers. This system detects an emergency braking situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce braking distances. Applying the brakes very quickly results in the best BAS assistance.
PAGE 347
STARTING AND OPERATING 345 power may also be reduced to assist in counteracting the condition of oversteer or understeer and help the vehicle maintain the desired path. The ESP uses sensors in the vehicle to determine the path that the driver intends to steer the vehicle and compares it to the actual path of the vehicle. When the actual path does not match the intended path, the ESP applies the brake of the appropriate wheel to assist in counteracting the condition of oversteer or understeer.
PAGE 348
346 STARTING AND OPERATING The ESP system has two available operating modes: ESP On This is the normal operating mode for the ESP. Whenever the vehicle is started, the ESP system will be in this mode. This mode should be used for most driving conditions. The ESP should only be turned OFF for specific reasons as noted in the following paragraphs. Partial Off The “Partial Off” mode is intended for times when a more spirited driving experience is desired.
PAGE 349
STARTING AND OPERATING 347 OFF switch. Once the situation requiring “Partial Off” mode is overcome, turn the ESP on again by momentarily depressing the ESP OFF switch. This may be done while the vehicle is in motion. Synchronizing ESP The Malfunction Indicator Light for the ESP is combined with BAS indicator. If the power supply is interrupted (battery disconnected or discharged), the ESP/BAS Malfunction Indicator Light may illuminate with the engine running.
PAGE 350
348 STARTING AND OPERATING NOTE: • The ESP/TCS Indicator Light and the ESP/BAS Malfunction Indicator Light will turn on momentarily each time the ignition switch is turned ON. TIRE SAFETY INFORMATION Tire Markings • Each time the ignition switch is turned ON, the ESP system will be on even if it was turned off previously. • The ESP control system will make buzzing or clicking sounds when it is active.
PAGE 351
STARTING AND OPERATING 349 NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • Temporary spare tires are high-pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation. Example: T145/80D18 103M.
PAGE 352
350 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
PAGE 353
STARTING AND OPERATING 351 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
PAGE 354
352 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
PAGE 355
STARTING AND OPERATING 353 Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. 5 Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires.
PAGE 356
354 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard and in the “Vehicle Loading” section of this manual.
PAGE 357
STARTING AND OPERATING 355 available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs [295 kg]). 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle.
PAGE 358
356 STARTING AND OPERATING
PAGE 359
STARTING AND OPERATING 357 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
PAGE 360
358 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement.
PAGE 361
STARTING AND OPERATING 359 CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.” Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.
PAGE 362
360 STARTING AND OPERATING loading may be required for high-speed vehicle operation. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Do not drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
PAGE 363
STARTING AND OPERATING 361 Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and reinstalled at the first opportunity. WARNING! Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). Temporary use spare tires have limited tread life.
PAGE 364
362 STARTING AND OPERATING vehicle, but it is not. Installation of this limited-use spare tire affects vehicle handling. Since it is not the same tire, replace (or repair) the original tire and reinstall on the vehicle at the first opportunity. Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck.
PAGE 365
STARTING AND OPERATING 363 Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Many states have laws requiring tire replacement at this point.
PAGE 366
364 STARTING AND OPERATING WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death. Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline.
PAGE 367
STARTING AND OPERATING 365 WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
PAGE 368
366 STARTING AND OPERATING SELF-SEALING TIRES — IF EQUIPPED A non-hardening viscous sealant applied to the inner liner of each tire fills punctures up to 0.19 in (5 mm) to minimize the loss of air pressure. This contributes to the safety of the vehicle by significantly reducing the probability of a roadside stop due to a flat tire. TIRE CHAINS Use only compact chains or other traction aids that meet SAE type “Class S” specifications.
PAGE 369
STARTING AND OPERATING 367 CAUTION! (Continued) • Do not drive for prolonged period on dry pavement. • Observe the tire chain manufacturer’s instructions on the method of installation, operating speed, and conditions for use. Always use the lower suggested operating speed of the chain manufacturer if different from the speed recommended by the manufacture. NOTE: In order to avoid damage to tires, chains, and your vehicle do not drive for a prolonged period on dry pavement.
PAGE 370
368 STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates and tend to develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all season type tires.
PAGE 371
STARTING AND OPERATING 369 TIRE PRESSURE MONITOR SYSTEM (TPMS) The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure. The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low-pressure warning limit for any reason, including low temperature effects and natural pressure loss through the tire. The tire pressure will vary with temperature by about 1 psi (6.9 kPa) for every 12°F (6.5°C).
PAGE 372
370 STARTING AND OPERATING For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 30 psi (207 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 27 psi (186 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressure to approximately 23 psi (158 kPa). This tire pressure is sufficiently low enough to turn ON the TPM Telltale Light.
PAGE 373
STARTING AND OPERATING 371 NOTE: • The TPMS is not intended to replace normal tire care and maintenance or to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. • Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
PAGE 374
372 STARTING AND OPERATING The matching full size spare wheel and tire assembly (if equipped) has a TPM sensor. The matching full size spare can be used in place of any of the four road tires. The TPMS will only monitor the pressure in the full size spare when it is used in place of a road tire. Otherwise, a spare with a pressure below the low-pressure limit will not cause the TPM Telltale Light to illuminate or the chime to sound.
PAGE 375
STARTING AND OPERATING 373 3. Accumulation of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPM sensors. NOTE: Vehicles with Full Size Spare 1. The matching full size spare wheel and tire assembly has a TPM sensor that can be monitored by the TPMS. 2.
PAGE 376
374 STARTING AND OPERATING 5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically and the TPM Telltale Light will turn OFF, as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information.
PAGE 377
STARTING AND OPERATING 375 Tire Pressure Monitoring Low Pressure Warnings The TPM Telltale Light will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. In addition, the EVIC will display one or more low pressure messages (Left Front, Left Rear, Right Front, Right Rear) for three seconds and a graphic showing the pressure values of each tire with the low tire pressure values flashing.
PAGE 378
376 STARTING AND OPERATING Should this occur, you should stop as soon as possible and inflate all of the tires with low pressure (including those flashing in the EVIC graphic) to the vehicle’s recommended cold placard pressure value. Once the system receives the updated tire pressures, the system will automatically update, the graphic display in the EVIC will stop flashing, and the TPM Telltale Light will turn off.
PAGE 379
STARTING AND OPERATING 377 If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the TPM Telltale Light will no longer flash, and the ⬙CHECK TPM SYSTEM⬙ message will no longer display, and a pressure value will display in place of the dashes. A system fault can occur due to any of the following: 1.
PAGE 380
378 STARTING AND OPERATING NOTE: Vehicles with Compact Spare 1. The compact spare tire does not have a TPM sensor. Therefore, the TPMS will not monitor the pressure in the compact spare tire. 2. If you install the compact spare tire in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition key cycle, the TPM Telltale Light will remain ON and a chime will sound. In addition, the graphic in the EVIC will still display a flashing pressure value. 3.
PAGE 381
STARTING AND OPERATING 379 General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. The TPM sensors are regulated under one of the following licenses: United States . . . . . . . . . . . . . . . . . . . . . KR5S120123 Canada . . . . . . . . . . . . . .
PAGE 382
380 STARTING AND OPERATING 3.5L and 5.7L Engines The 3.5L and 5.7L Engines are designed to meet all emissions regulations and provide satisfactory fuel economy and performance when using high-quality unleaded gasoline having an octane range of 87 to 89. The manufacturer recommends the use of 89 octane for optimum performance. The use of premium gasoline is not recommended.
PAGE 383
STARTING AND OPERATING 381 The manufacturer supports the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability of engine and fuel system components. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as 10% ethanol, MTBE, and ETBE. Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions.
PAGE 384
382 STARTING AND OPERATING To fix a Non-FFV vehicle inadvertently fueled once with E-85 perform the following: • change the engine oil and oil filter • disconnect and reconnect the battery • drain the fuel tank (see your authorized dealer) More extensive repairs will be required for prolonged exposure to E-85 fuel. MMT In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasoline to increase octane.
PAGE 385
STARTING AND OPERATING 383 Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance and damage the emissions control system. • An out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat.
PAGE 386
384 STARTING AND OPERATING stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle. edge) of the fuel filler door to access the fuel filler cap. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly.
PAGE 387
STARTING AND OPERATING 385 NOTE: When removing the fuel filler cap, lay the cap tether in the hook, located on the fuel filler cap door reinforcement. Gas Cap Tether Hook CAUTION! • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap could let impurities into the fuel system. • A poorly fitting gas cap may cause the Malfunction Indicator Light (MIL) to turn on.
PAGE 388
386 STARTING AND OPERATING WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel to the vehicle when the engine is running. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. NOTE: • Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is tightened properly.
PAGE 389
STARTING AND OPERATING 387 VEHICLE LOADING The load carrying capacity of your vehicle is shown on the “Vehicle Certification Label.” This information should be used for passenger and luggage loading as indicated. Do not exceed the specified Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Rating (GAWR). Vehicle Certification Label Your vehicle has a Vehicle Certification Label affixed to the rear of the driver’s door.
PAGE 390
388 STARTING AND OPERATING WARNING! Because the front wheels steer the vehicle, it is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident. Overloading The load carrying components (axle, springs, tires, wheels, etc.) of your vehicle will provide satisfactory service as long as you do not exceed the GVWR and the front and rear GAWR.
PAGE 391
STARTING AND OPERATING 389 NOTE: • Refer to the “Vehicle Certification Label” affixed to the rear of the driver’s door for your vehicle’s GVWR and GAWRs. • Refer to the “Tire Placard” for your vehicle’s proper tire pressure. TRAILER TOWING In this section, you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.
PAGE 392
390 STARTING AND OPERATING Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination. (Note that GCWR ratings include a 150 lbs [68 kg] allowance for the presence of a driver.) Tongue Weight (TW) The TW is the downward force exerted on the hitch ball by the trailer. In most cases, it should not be less than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle.
PAGE 393
STARTING AND OPERATING 391 Weight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle. These kinds of hitches are the most popular on the market today and they are commonly used to tow small- and mediumsized trailers. Weight-Distributing Hitch A weight-distributing system works by applying leverage through spring (load) bars.
PAGE 394
392 STARTING AND OPERATING Trailer Hitch Classification Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package. See your authorized dealer for package content. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
PAGE 395
STARTING AND OPERATING 393 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission Frontal Area Max. GTW (Gross Trailer Wt.) 1,000 lbs (454 kg) Max. Tongue Wt. (〫 see note) 100 lbs (45 kg) 2.7L & 3.5L Rear Wheel 22 sq ft (2.04 sq m) Drive (RWD) Automatic 3.5L All Wheel Drive 32 sq ft (2.97 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) (AWD) & 5.
PAGE 396
394 STARTING AND OPERATING Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of the vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents.
PAGE 397
STARTING AND OPERATING 395 NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to the “Tire and Loading Information” placard for the maximum combined weight of occupants and cargo for your vehicle.
PAGE 398
396 STARTING AND OPERATING • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle automatic transmission in PARK. Always, block or ⬙chock⬙ the trailer wheels. • GCWR must not be exceeded.
PAGE 399
STARTING AND OPERATING 397 − Check for signs of tire wear or visible tire damage before towing a trailer. Refer to “Tires–General Information” in this section for information on tread wear indicators and for the proper inspection procedure. − When replacing tires, refer to “Tires–General Information” in this section for information on replacement tires and for the proper tire replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s GVWR and GAWR limits.
PAGE 400
398 STARTING AND OPERATING WARNING! Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. Towing any trailer will increase your stopping distance. When towing, you should allow for additional space between your vehicle and the vehicle in front of you. Failure to do so could result in an accident.
PAGE 401
STARTING AND OPERATING 399 5 4-Pin Connector 1 — Female Pins 2 — Male Pin 3 — Ground 4 — Park 5 — Left Stop/Turn 6 — Right Stop/Turn 7-Pin Connector 1 2 3 4 — — — — Battery Backup Lamps Right Stop/Turn Electric Brakes 5 — Ground 6 — Left Stop/Turn 7 — Running Lamps
PAGE 402
400 STARTING AND OPERATING Towing Tips Before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Towing Tips — Automatic Transmission The DRIVE range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected.
PAGE 403
STARTING AND OPERATING 401 − Extended driving at high RPM should be avoided to prevent excess heat generation. A reduction in vehicle speed may be required to avoid extended driving at high RPM. Return to a higher gear range or vehicle speed when road conditions and RPM level allows. Towing Tips — Cooling System To reduce potential for engine and transmission overheating, take the following actions: − City Driving When stopped for short periods, put transmission in NEUTRAL and increase engine idle speed.
PAGE 404
PAGE 405
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . 404 䡵 Jump-Starting Procedures . . . . . . . . . . . . . . . . 417 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 405 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 420 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 406 䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . 421 ▫ Jack Location/Spare Tire Stowage . . . . . . . . 406 ▫ Without The Ignition Key . . . . . .
PAGE 406
404 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning flasher switch is located in the center of the instrument panel between the center air outlets. Press the Hazard Warning flasher switch to activate the flashers. When activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off the flashers. This is an emergency warning system and it should not be used when the vehicle is in motion.
PAGE 407
WHAT TO DO IN EMERGENCIES 405 IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. • On the highways — slow down. • In city traffic — while stopped, put transmission in NEUTRAL, but do not increase engine idle speed. NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off.
PAGE 408
406 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! (Continued) WARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack.
PAGE 409
WHAT TO DO IN EMERGENCIES 407 2. Lift the access cover using the pull strap. 3. Remove the fastener securing the spare tire.
PAGE 410
408 WHAT TO DO IN EMERGENCIES 4. Remove the spare tire. 5. Remove the fastener securing the jack. WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Preparations For Jacking 1. Park the vehicle on a firm level surface as far from the edge of the roadway as possible. Avoid icy or slippery areas. 2. Set the parking brake. 3. Place the shift lever into PARK.
PAGE 411
WHAT TO DO IN EMERGENCIES 409 6. Block the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked.
PAGE 412
410 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • If working on or near a roadway, be extremely careful of motor traffic. • To assure that spare tires, flat or inflated are securely stowed, spares must be stowed with the valve stem facing the ground. • Turn on the Hazard Warning Flasher. 2. If equipped with steel wheels, do not remove the wheel cover at this time.
PAGE 413
WHAT TO DO IN EMERGENCIES 411 WARNING! To avoid possible personal injury, handle the wheel covers with care to avoid contact with the metal edges and retention teeth. 3. Before raising the vehicle, use the lug wrench to loosen, but not remove, the lug nuts on the wheel with the flat tire. Turn the lug nuts counterclockwise one turn while the wheel is still on the ground. 6 Lug Nut Removal/Installation 1 — Tighten 2 — Loosen 4. Place the jack underneath the lift area that is closest to the flat tire.
PAGE 414
412 WHAT TO DO IN EMERGENCIES Jack Engagement Locations
PAGE 415
WHAT TO DO IN EMERGENCIES 413 5. Raise the vehicle just enough to remove the flat tire and install the spare tire. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts, wheel cover (if equipped), and tire. Remove the cover by hand. Do not pry it off. 7. Mount the spare tire.
PAGE 416
414 WHAT TO DO IN EMERGENCIES WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Compact Spare Tire The compact spare tire is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and reinstalled at the first opportunity.
PAGE 417
WHAT TO DO IN EMERGENCIES 415 Wheel Cover or Center Cap Installation (If Required) NOTE: Do not attempt to install a center cap or wheel cover on the compact spare. 1. Mount the road tire on the axle. For vehicles equipped with wheel covers, perform Steps 2 and 3. For vehicles equipped with center caps, proceed to Step 4. 2. Install two lug nuts on the mounting studs, which are on each side of the stud that is in alignment with the valve stem.
PAGE 418
416 WHAT TO DO IN EMERGENCIES 3. Align the valve notch in the wheel cover with the valve stem on the wheel. Install the cover by hand, snapping the cover over the two lug nuts. Do not use a hammer or excessive force to install the cover. 4. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle is lowered to the ground. 5.
PAGE 419
WHAT TO DO IN EMERGENCIES 417 JUMP-STARTING PROCEDURES WARNING! (Continued) WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be hurt by the fan. • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
PAGE 420
418 WHAT TO DO IN EMERGENCIES NOTE: The battery is stored under an access cover in the trunk. Remote battery terminals are located in the engine compartment for jump-starting. 3. Set the parking brake, place the automatic transmission in PARK, and turn the ignition switch to the LOCK position on both vehicles. 1. Wear eye protection and remove any metal jewelry such as watchbands or bracelets that might make an inadvertent electrical contact. 4.
PAGE 421
WHAT TO DO IN EMERGENCIES 419 6. Connect the other cable, first to the negative terminal of the booster battery and then to the engine ground (-) of the vehicle with the discharged battery. Make sure you have a good contact on the engine ground. Refer to the following illustration for jump-starting connections. WARNING! • You should not try to start your vehicle by pushing or towing. • Do not connect the cable to the negative post of the discharged battery.
PAGE 422
420 WHAT TO DO IN EMERGENCIES NOTE: Refer to ⬙Synchronizing ESP⬙ under ⬙Electronic Stability Program⬙ in Section 5 if the ESP/BAS light (in the instrument cluster) remains on continuously after starting the engine of the vehicle with the discharged battery. 8. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan.
PAGE 423
WHAT TO DO IN EMERGENCIES 421 CAUTION! WARNING! • When “rocking” a stuck vehicle by moving between 1st and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result. • Racing the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 35 mph (55 km/h). Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure.
PAGE 424
422 WHAT TO DO IN EMERGENCIES Towing This Vehicle Behind Another Vehicle (Flat Towing With All Four Wheels On The Ground) Flat towing of vehicles equipped with an automatic transmission, is only permitted within the following limitations. With The Ignition Key Your vehicle may be towed under the following conditions: The shift lever must be in NEUTRAL, the distance to be traveled must not exceed 30 miles (48 km), and the towing speed must not exceed 30 mph (48 km/h).
PAGE 425
WHAT TO DO IN EMERGENCIES 423 If you must use the accessories (wipers, defrosters, etc.) while being towed, the key must be in the ON position, not the ACC position. Make certain the transmission remains in NEUTRAL. Towing This Vehicle Behind Another Vehicle With A Tow Dolly The manufacturer does not recommend that you tow this vehicle on a tow dolly. Vehicle damage may occur.
PAGE 426
PAGE 427
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 2.7L . . . . . . . . . . . . . 427 䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . 433 䡵 Engine Compartment — 3.5L . . . . . . . . . . . . . 428 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 433 䡵 Engine Compartment — 5.7L . . . . . . . . . . . . . 429 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 437 䡵 Onboard Diagnostic System — OBD II . . . . . . 430 ▫ Engine Air Cleaner Filter . . . . . . . . . .
PAGE 428
426 MAINTAINING YOUR VEHICLE ▫ Windshield Washers/Headlight Washers — If Equipped . . . . . . . . . . . . . . . . . . . . . . 442 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . 443 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . 445 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . 451 ▫ Automatic Transmission . . . . . . . . . . . . . . . 452 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . .
PAGE 429
MAINTAINING YOUR VEHICLE 427 ENGINE COMPARTMENT — 2.
PAGE 430
428 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 3.
PAGE 431
MAINTAINING YOUR VEHICLE 429 ENGINE COMPARTMENT — 5.
PAGE 432
430 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
PAGE 433
MAINTAINING YOUR VEHICLE 431 TRIP ODOMETER button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. serviced, recently had a dead battery, or a battery replacement. If the OBD II system should be determined not ready for the I/M test, your vehicle may fail the test. A loose, improperly installed, or damaged fuel filler cap may also turn on the MIL.
PAGE 434
432 MAINTAINING YOUR VEHICLE 5. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn OFF the ignition or start the engine.
PAGE 435
MAINTAINING YOUR VEHICLE 433 DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
PAGE 436
434 MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about five minutes after a fully warmed engine is shut off. The best time to check the engine oil level is about five minutes after a fully warmed engine is shut off. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between the MIN and MAX markings on the dipstick. Adding 1.0 qt (1.
PAGE 437
MAINTAINING YOUR VEHICLE 435 NOTE: Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, whichever occurs first. Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API Certified and meet the requirements of Chrysler Material Standard MS-6395.
PAGE 438
436 MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) — 3.5L Engine SAE 10W-30 engine oil is recommended for all operating temperatures. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to “Engine Compartment” in this section. Lubricants which do not have both, the engine oil certification mark and the correct SAE viscosity grade number should not be used.
PAGE 439
MAINTAINING YOUR VEHICLE 437 Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Engine Oil Filter Selection This manufacturer’s engines have a full-flow type oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high quality filters should be used to assure most efficient service. MOPAR威 engine oil filters are a high quality oil filter and are recommended.
PAGE 440
438 MAINTAINING YOUR VEHICLE Maintenance-Free Battery The top of the maintenance-free battery is permanently sealed. You will never have to add water, nor is periodic maintenance required. NOTE: The battery is stored under an access cover in the trunk. Remote battery terminals are located in the engine compartment for jump-starting.
PAGE 441
MAINTAINING YOUR VEHICLE 439 WARNING! WARNING! (Continued) • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. • Battery gas is flammable and explosive. Keep flame or sparks away from the battery.
PAGE 442
440 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system.
PAGE 443
MAINTAINING YOUR VEHICLE 441 A/C Air Filter The filter is located in the fresh air inlet under the hood, behind a removable panel in the cowl on the passenger side of the vehicle, next to the windshield wipers. When installing a new filter, ensure its proper orientation. To replace the filter, remove the access door in the cowl screen by pressing the retaining clips. Slide the lid on the filter adapter forward and down and remove the used filter.
PAGE 444
442 MAINTAINING YOUR VEHICLE Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc.
PAGE 445
MAINTAINING YOUR VEHICLE 443 WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
PAGE 446
444 MAINTAINING YOUR VEHICLE CAUTION! WARNING! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle.
PAGE 447
MAINTAINING YOUR VEHICLE 445 To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idling or malfunctioning operating conditions.
PAGE 448
446 MAINTAINING YOUR VEHICLE rusty in appearance, the system should be drained, flushed, and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Check the coolant recovery bottle tubing for brittle rubber, cracking, tears, cuts, and tightness of the connection at the bottle and radiator. Inspect the entire system for leaks.
PAGE 449
MAINTAINING YOUR VEHICLE 447 CAUTION! CAUTION! (Continued) • Mixing of engine coolant (antifreeze) other than specified HOAT engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. If a non-HOAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with the specified engine coolant (antifreeze) as soon as possible. • Do not use water alone or alcohol-based engine coolant (antifreeze) products.
PAGE 450
448 MAINTAINING YOUR VEHICLE When adding engine coolant (antifreeze): • The manufacturer recommends using MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology). • Mix a minimum solution of 50% HOAT engine coolant (antifreeze) and distilled water. Use higher concentrations (not to exceed 70%) if temperatures below ⫺34°F (⫺37°C) are anticipated.
PAGE 451
MAINTAINING YOUR VEHICLE 449 WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
PAGE 452
450 MAINTAINING YOUR VEHICLE When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to Remember NOTE: When the vehicle is stopped after a few miles (kilometers) of operation, you may observe vapor coming from the front of the engine compartment.
PAGE 453
MAINTAINING YOUR VEHICLE 451 • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emissions. Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals.
PAGE 454
452 MAINTAINING YOUR VEHICLE WARNING! • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. • Use of a brake fluid that may have a lower initial boiling point, or is unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident. Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter or moisture.
PAGE 455
MAINTAINING YOUR VEHICLE 453 CAUTION! (Continued) • The fluid level is preset at the factory and it does not require adjustment under normal operating conditions. If a transmission fluid leak occurs, visit your authorized dealer immediately. Severe damage to the transmission may occur. Your authorized dealer has the proper tools to adjust the fluid level accurately. Fluid and Filter Changes Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals.
PAGE 456
454 MAINTAINING YOUR VEHICLE All Wheel Drive (AWD) — If Equipped The all wheel drive system consists of a transfer case and front differential. The exterior surface of these components should be inspected for evidence of fluid leaks. Confirmed leaks should be repaired as soon as possible. The transfer case fluid fill/inspection plug is located in the middle of the rear housing. To inspect the transfer case fluid level, remove the fill/inspection plug.
PAGE 457
MAINTAINING YOUR VEHICLE 455 The most common causes are: • Road salt, dirt, and moisture accumulation. • Stone and gravel impact. • Insects, tree sap, and tar. • Salt in the air near seacoast localities. • Use MOPAR威 Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. • Atmospheric fallout/industrial pollutants.
PAGE 458
456 MAINTAINING YOUR VEHICLE • It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open. • Use MOPAR威 Touch Up Paint or equivalent on scratches as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle. • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner.
PAGE 459
MAINTAINING YOUR VEHICLE 457 Interior Trim should be cleaned starting with a damp cloth, or MOPAR威 Satin Select. Do not use harsh cleaners or Armorall. Use MOPAR威 Total Clean to clean vinyl upholstery. MOPAR威 Total Clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth.
PAGE 460
458 MAINTAINING YOUR VEHICLE Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOPAR威 Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear window equipped with electric defrosters or the right rear quarter window equipped with the radio antenna. Do not use scrapers or other sharp instrument that may scratch the elements.
PAGE 461
MAINTAINING YOUR VEHICLE 459 Cleaning the Center Console Cupholders Clean with a damp cloth or towel using a mild detergent with the cupholder in the center console. NOTE: The cupholder cannot be removed. FUSES Integrated Power Module The Integrated Power Module (IPM) is located in the engine compartment. This module contains fuses and relays.
PAGE 462
460 MAINTAINING YOUR VEHICLE CAUTION! • When installing the integrated power module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the integrated power module and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
PAGE 463
MAINTAINING YOUR VEHICLE 461 Cavity 10 11 12 13 14 Cartridge Fuse 30 Amp Pink 30 Amp Pink MiniFuse Description Cavity — Windshield Wiper 15 — Anti-Lock Brake System (ABS) Valves - If Equipped Radiator Fan 16 17 18 19 20 21 22 40 Amp — Green 50 Amp — Red — — Anti-Lock Brake System (ABS) Pump Motor - If Equipped — Cartridge Fuse 50 Amp Red — — — — — — — MiniFuse Description — Radiator Fan — — — — — — — — — — — — — — 7
PAGE 464
462 MAINTAINING YOUR VEHICLE Rear Power Distribution Center There is also a power distribution center located in the trunk under the spare tire access panel. This center contains fuses and relays.
PAGE 465
MAINTAINING YOUR VEHICLE 463 CAUTION! • When installing the power distribution center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
PAGE 466
464 MAINTAINING YOUR VEHICLE Cavity 8 Cartridge Fuse — 9 — 10 11 * 12 * 13 * 14 — — — — — 15 — 16 — MiniFuse Description Cavity 15 Amp Blue Diagnostic Link Connector (DLC)/Wireless Control Module (WCM)/Wireless Ignition Node (WIN) Power Outlet 17 Cartridge Fuse — 18 — 19 — — — — — AC Heater Control/ Cluster/Security Module If Equipped Trailer Tow Brake Module - If Equipped — 20 21 22 23 24 25 26 27 — — — — — — — — 20 Amp Yellow — — — — 10 Amp Red 20 Amp Yellow — MiniFuse Descript
PAGE 467
MAINTAINING YOUR VEHICLE 465 Cavity 28 Cartridge Fuse — 29 — MiniFuse Description Cavity 10 Amp Red 5 Amp Orange Ignition Run 35 Cartridge Fuse — 36 — 20 Amp Yellow 37 — 38 — 15 Amp Blue 10 Amp Red 30 — 10 Amp Red 31 32 33 34 — — — — — — — — Adaptive Cruise Control (ACC) - If Equipped/ Cluster/Electronic Stability Program (ESP) - If Equipped/Powertrain Control Module (PCM)/ STOP LIGHT Switch Door Modules/Power Mirrors/Steering Control Module (SCM) — — — — 39 — MiniFuse Descrip
PAGE 468
466 MAINTAINING YOUR VEHICLE Cavity 40 Cartridge Fuse — MiniFuse Description Cavity 5 Amp Orange 44 41 — 10 Amp Red 42 30 Amp Pink 30 Amp Pink — Auto Inside Rearview Mirror - If Equipped/Heated Seats - If Equipped/Switch Bank AC Heater Control/ Headlights/Park Assist - If Equipped/Tire Pressure Monitoring - If Equipped/ Occupant Restraint Controller (ORC) Front Blower Motor — Rear Window Defroster 43 Cartridge Fuse 20 Amp Blue MiniFuse Description — Amplifier - If Equipped/ Sunroof -
PAGE 469
MAINTAINING YOUR VEHICLE 467 VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery. • Disconnect the negative cable from the battery. • Anytime you store your vehicle, or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower setting.
PAGE 470
468 MAINTAINING YOUR VEHICLE Exterior (300 Models) Bulb Number Low Beam Headlight . . . . . . . . . . . . . . . . . . . . . 9006 High Beam Headlight. . . . . . . . . . . . . . . . . . . . . 9005 Front Park/Turn Light . . . . . . . . . . . . . . . . . . . . 3157 Front Inner Park Light . . . . . . . . . . . . . . . . . . 194NA Front Outer Park Light . . . . . . . . . . . . . . . . . . 194NA Front Fog Light—If Equipped. . . . . . . . . . . . 9145/H10 (Serviced at Authorized Dealer) Front Sidemarker . . . . .
PAGE 471
MAINTAINING YOUR VEHICLE 469 BULB REPLACEMENT Low Beam Headlight, High Beam Headlight, Park/Turn Light, Inner Park Light, and Outer Park Light – 300 Models 1. Open the hood. NOTE: Removal of the air cleaner filter housing may be necessary prior to replacing bulbs in the headlight assembly on the driver side of the vehicle. 2. Twist the appropriate bulb and socket assembly counterclockwise, and then pull it out of the headlight assembly. 3.
PAGE 472
470 MAINTAINING YOUR VEHICLE 3 — Park/Turn Light Bulb 4 — Inner Park Light Bulb 5 — Outer Park Light Bulb
PAGE 473
MAINTAINING YOUR VEHICLE 471 CAUTION! WARNING! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. A transient high tension occurs at the bulb sockets of HID headlights when the headlight switch is turned ON. It may cause serious electrical shock or electrocution if not serviced properly. See your authorized dealer for service.
PAGE 474
472 MAINTAINING YOUR VEHICLE Backup Light, Side Marker Light, and Tail/Stop Turn Light — 300 Models 4. Remove the remaining fastener from the back of the tail light assembly. 1. Open the Trunk. 5. Push the electrical connector locking tab to the side. 2. Remove two fasteners from the back of the tail light assembly. 6. Disconnect the electrical connector. 3. Pull back the trunk liner. 7. Pull the tail light assembly clear from the vehicle to access the bulbs.
PAGE 475
MAINTAINING YOUR VEHICLE 473 8. Turn the appropriate bulb and socket assembly counterclockwise to remove it from the tail light assembly.
PAGE 476
474 MAINTAINING YOUR VEHICLE 9. Disconnect the bulb from the socket assembly and install the replacement bulb. 10. Reinstall the bulb and socket assembly into the tail light assembly, and then turn it clockwise. 11. Reinstall the tail light assembly, fasteners, electrical connector, and trunk liner. 12. Close the trunk.
PAGE 477
MAINTAINING YOUR VEHICLE 475 Tail/Stop, Tail, Turn Signal Light, and Backup Light — 300C Models 4. Remove the remaining fastener from the back of the tail light assembly. 1. Open the Trunk. 5. Push the electrical connector locking tab to the side. 2. Remove two fasteners from the back of the tail light assembly. 6. Disconnect the electrical connector. 7 3. Pull back the trunk liner.
PAGE 478
476 MAINTAINING YOUR VEHICLE 7. Pull the tail light assembly clear from the vehicle to access the bulbs. Turn bulb sockets counterclockwise to remove. 8. Turn the appropriate bulb and socket assembly counterclockwise to remove it from the tail light assembly.
PAGE 479
MAINTAINING YOUR VEHICLE 477 3 — Turn Signal Light Bulb 4 — Backup Light Bulb 9. Disconnect the bulb from the socket assembly and install the replacement bulb. 10. Reinstall the bulb and socket assembly into the tail light assembly, and then turn it clockwise.
PAGE 480
478 MAINTAINING YOUR VEHICLE 11. Reinstall the tail light assembly, fasteners, electrical connector, and trunk liner. 12. Close the trunk. License Light 1. Remove the screws securing the light to the rear fascia. 2. Remove the bulb and socket assembly. 3. Disconnect the bulb from the socket assembly and install the replacement bulb. 1 — License Light Bulb 2 — Socket 4. Reinstall the bulb and socket assembly. 5. Reattach the light to the rear fascia, and then install the screws.
PAGE 481
MAINTAINING YOUR VEHICLE 479 FLUIDS AND CAPACITIES U.S. Fuel (Approximate) 2.7 Liter Engine 3.5 Liter Engine without All Wheel Drive 3.5 Liter Engine with All Wheel Drive 5.7 Liter Engine Engine Oil with Filter 2.7 Liter Engine (SAE 5W-20, API Certified) 3.5 Liter Engine (SAE 10W-30, API Certified) 5.7 Liter Engine (SAE 5W-20, API Certified) 18 18 19 19 Gallons Gallons Gallons Gallons 6.0 Quarts 6.0 Quarts 7.0 Quarts Metric 68 68 72 72 Liters Liters Liters Liters 5.7 Liters 5.7 Liters 6.
PAGE 482
480 MAINTAINING YOUR VEHICLE Cooling System * 2.7 Liter Engine (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent 3.5 Liter Engine without All Wheel Drive (MOPAR威 Antifreeze/ Coolant 5 Year/100,000 Mile Formula) or equivalent 3.5 Liter Engine with All Wheel Drive (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent 5.7 Liter Engine without Severe Duty II Cooling System (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent 5.
PAGE 483
MAINTAINING YOUR VEHICLE 481 FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil (2.7L Engine) Engine Oil (3.5L Engine) Engine Oil (5.7L Engine) Spark Plugs (2.7L Engine) Spark Plugs (3.5L Engine) Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
PAGE 484
482 MAINTAINING YOUR VEHICLE Component Spark Plugs (5.7L Engine) Oil Filter (2.7L, 3.5L, and 5.7L Engines) Fuel Selection (2.7L Engine) Fuel Selection (3.5L and 5.7L Engines) Fluid, Lubricant, or Genuine Part LZFR5C–11 (Gap 0.043 in [1.
PAGE 485
MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . 484 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 484 ▫ Required Maintenance Intervals . . . . . . . . . .
PAGE 486
M A I N T E N A N C E 484 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type, must be done at the times or mileages specified to ensure the continued proper functioning of the Emissions Control System. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
PAGE 487
MAINTENANCE SCHEDULES 485 M NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or six months, whichever comes first.
PAGE 488
M A I N T E N A N C E S C H E D U L E S 8 486 MAINTENANCE SCHEDULES At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines. CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle. Required Maintenance Intervals Refer to the Maintenance Schedules on the following pages for the required maintenance intervals.
PAGE 489
MAINTENANCE SCHEDULES 487 M 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
PAGE 490
M 488 MAINTENANCE SCHEDULES A I N 18,000 Miles (30,000 km) or T 18 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ Inspect the rear axle fluid. Inspect the S C H E D U L E S 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
PAGE 491
MAINTENANCE SCHEDULES 489 M 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Replace the air conditioning filter (if equipped) ❏ Inspect the rear axle fluid. Inspect the front axle fluid — All Wheel Drive (AWD).
PAGE 492
M 490 MAINTENANCE SCHEDULES A I N 42,000 Miles (70,000 km) or T 42 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
PAGE 493
MAINTENANCE SCHEDULES 491 M 54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the spark plugs (2.7L and 5.7L Engines). Replace the air conditioning filter (if equipped) Inspect the brake linings; replace if necessary. Adjust parking brake on vehicles equipped with four-wheel disc brakes.
PAGE 494
M 492 MAINTENANCE SCHEDULES A I N 66,000 Miles (110,000 km) or T 66 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
PAGE 495
MAINTENANCE SCHEDULES 493 M 78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
PAGE 496
M 494 MAINTENANCE SCHEDULES A I N 90,000 Miles (150,000 km) or 90 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ Replace the engine air cleaner filter. C ❏ Replace the spark plugs (2.7L and 5.7L Engines). E ❏ Inspect and replace PCV valve if necessary. † S C H E D U L E S ❏ Inspect the rear axle fluid. Inspect the front axle fluid — All Wheel Drive (AWD). ❏ Inspect the transfer case fluid — All Wheel Drive (AWD).
PAGE 497
MAINTENANCE SCHEDULES 495 M 96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Replace the air conditioning filter (if equipped) ❏ Inspect the brake linings; replace if necessary. ❏ Inspect the CV joints. ❏ Inspect exhaust system.
PAGE 498
M 496 MAINTENANCE SCHEDULES A I N 108,000 Miles (180,000 km) or 108 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. C E ❏ Replace the air conditioning filter (if equipped) S C H E D U L E S 114,000 Miles (190,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter.
PAGE 499
MAINTENANCE SCHEDULES 497 M 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the air conditioning filter (if equipped) Replace the spark plugs (2.7L and 5.7L Engines). Inspect the brake linings; replace if necessary. Adjust parking brake on vehicles equipped with four-wheel disc brakes. Inspect the CV joints. Inspect exhaust system.
PAGE 500
M 498 MAINTENANCE SCHEDULES A I N 132,000 Miles (220,000 km) or T 132 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ If using your vehicle for any of the S C H E D U L E S 138,000 Miles (230,000 km) or 138 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
PAGE 501
MAINTENANCE SCHEDULES 499 M 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Replace the air conditioning filter (if equipped) ❏ Inspect the brake linings; replace if necessary. ❏ Inspect the CV joints. ❏ Inspect exhaust system.
PAGE 502
M A I N T E N A N C E S C H E D U L E S 8 500 MAINTENANCE SCHEDULES † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
PAGE 503
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 505 ▫ Prepare For The Appointment . . . . . . . . . . . 503 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 505 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 503 䡵 Warranty Information (U.S. Vehicles Only) . . . .
PAGE 504
502 IF YOU NEED CONSUMER ASSISTANCE 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 508 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 509 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 509 ▫ Temperature Grades . . . . . . . . . . . . . . . . . .
PAGE 505
IF YOU NEED CONSUMER ASSISTANCE 503 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
PAGE 506
504 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealership. They want to know if you need assistance. • If an authorized dealership is unable to resolve the concern, you may contact the manufacturer’s customer center.
PAGE 507
IF YOU NEED CONSUMER ASSISTANCE 505 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
PAGE 508
506 IF YOU NEED CONSUMER ASSISTANCE WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. WARRANTY INFORMATION (U.S.
PAGE 509
IF YOU NEED CONSUMER ASSISTANCE 507 To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov. PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below.
PAGE 510
508 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-bystep troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.
PAGE 511
IF YOU NEED CONSUMER ASSISTANCE 509 Treadwear The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
PAGE 512
510 IF YOU NEED CONSUMER ASSISTANCE Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law. WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
PAGE 513
INDEX 10
PAGE 514
512 INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . . 339 ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . 341 Adaptive Cruise Control (ACC) (Cruise Control) . . 157 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 447 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 384 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 442 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 382 Adjustable Pedals . . . . . . . . . . . . . . . . .
PAGE 515
INDEX 513 Auto Down Power Windows . . . . . . . . . . . . . . . . 38 Auto Unlock, Doors . . . . . . . . . . . . . . . . . . . . . . . 32 Auto Up Power Windows . . . . . . . . . . . . . . . . . . 39 Automatic Dimming Mirror . . . . . . . . . . . . . . . . . 90 Automatic Door Locks . . . . . . . . . . . . . . . . . . . 31,32 Automatic Headlights . . . . . . . . . . . . . . . . . . . . 140 Automatic Oil Change Indicator . . . . . . . . . . . 211,227 Automatic Temperature Control (ATC) . . . . . . . . .
PAGE 516
514 INDEX Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 482 Brake, Parking . . . . . . . . . . . . . . . . . . . . . . . . . . 339 Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . 451 Anti-Lock (ABS) . . . . . . . . . . . . . . . . . . . . . . . 341 Fluid Check . . . . . . . . . . . . . . . . . . . . . . . 451,482 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . 451 Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339 Warning Light . . .
PAGE 517
INDEX 515 Cleaning Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 456 Windshield Wiper Blades . . . . . . . . . . . . . . . . . 441 Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . 298 Clock . . . . . . . . . . . . . . . . . . . . . 242,244,258,262,271 Coin Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 Compact Disc (CD) Maintenance . . . . . . . . . . . . . 297 Compact Spare Tire . . . . . . . . . . . . . . . . . . . . . . 361 Compass . . . . . . . . .
PAGE 518
516 INDEX Data Recorder, Event . . . . . . . . . . . . . . . . . . . . . . 66 Daytime Brightness, Interior Lights . . . . . . . . . . . 146 Daytime Running Lights . . . . . . . . . . . . . . . . . . . 143 Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . . . 433 Deck Lid, Emergency Release . . . . . . . . . . . . . . . . 43 Deck Lid, Power Release . . . . . . . . . . . . . . . . . . . 42 Defroster, Rear Window . . . . . . . . . . . . . . . . . . . 201 Defroster, Windshield . . . . . . . . . .
PAGE 519
INDEX 517 Electronic Throttle Control Warning Light . . . . . . 218 Electronic Vehicle Information Center (EVIC) . . . . 221 Emergency Deck Lid Release . . . . . . . . . . . . . . . . 43 Emergency, In Case of Freeing Vehicle When Stuck . . . . . . . . . . . . . . . 420 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 404 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 417 Overheating . . . . . . . . . . . . . . .
PAGE 520
518 INDEX Entry System, Illuminated . . . . . . . . . . . . . . . . . . 20 Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381 Event Data Recorder . . . . . . . . . . . . . . . . . . . . . . 66 Exhaust Gas Caution . . . . . . . . . . . . . . . . 79,383,443 Exhaust System . . . . . . . . . . . . . . . . . . . . . . . 79,443 Exterior Folding Mirrors . . . . . . . . . . . . . . . . . . . 91 Exterior Lighting . . . . . . . . . . . . . . . . . . . . . . . . 139 Exterior Lights . . . . . .
PAGE 521
INDEX 519 Additives . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382 Clean Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380 Conserving . . . . . . . . . . . . . . . . . . . . . . . . . . 228 Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381 Filler Cap (Gas Cap) . . . . . . . . . . . . . . . . . . . . 384 Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217 Materials Added . .
PAGE 522
520 INDEX Hands-Free Phone (UConnect威) . . . . . . . . . . . . . . 94 Hazard Driving Through Flowing, Rising, or Shallow Standing Water . . . . . . . . . . . . . . . . . . . . . . . . 335 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . . 404 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . 130 Headlight Washers . . . . . . . . . . . . . . . . . . . . . . . 442 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 471 Automatic . . . . . . . . . . . . . . . . . . . .
PAGE 523
INDEX 521 Information Center, Vehicle . . . . . . . . . . . . . . . . . 221 Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . . 89 Instrument Cluster . . . . . . . . . . . . . . . . . . . . 208,210 Instrument Panel and Controls . . . . . . . . . . . . . . 207 Instrument Panel Lens Cleaning . . . . . . . . . . . . . 458 Integrated Power Module (Fuses) . . . . . . . . . . . . 459 Interior Appearance Care . . . . . . . . . . . . . . . . . . 456 Interior Fuses . . . . . . . . . . . . . . . . . . . .
PAGE 524
522 INDEX Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81,139 Airbag . . . . . . . . . . . . . . . . . . . . . . . . 61,66,80,213 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 Automatic Headlights . . . . . . . . . . . . . . . . . . . 140 Brake Assist Warning . . . . . . . . . . . . . . . . . . . 347 Brake Warning . . . . . . . . . . . . . . . . . . . . . . . . 214 Bulb Replacement . . . . . . . . . . . . . . . . . . . 467,469 Courtesy/Reading . . . . . . . . . .
PAGE 525
INDEX 523 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . 217 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . 467,469 Service Engine Soon (Malfunction Indicator) . . . 220 SmartBeams . . . . . . . . . . . . . . . . . . . . . . . . . . 141 Tire Pressure Monitoring (TPMS) . . . . . . . . 218,369 Traction Control . . . . . . . . . . . . . . . . . . . . . . . 347 Turn Signal . . . . . . . . . . . . . . . . . . . . . . 81,144,210 Vanity Mirror . . . . . . . . . . . . . . . . . . . . .
PAGE 526
524 INDEX Methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381 Mini-Trip Computer . . . . . . . . . . . . . . . . . . . . . . 228 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Automatic Dimming . . . . . . . . . . . . . . . . . . . . . 90 Electric Powered . . . . . . . . . . . . . . . . . . . . . . . 93 Electric Remote . . . . . . . . . . . . . . . . . . . . . . . . 93 Exterior Folding . . . . . . . . . . . . . . . . . . . . . . . . 91 Heated . . . . . . . . .
PAGE 527
INDEX 525 Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436 Viscosity . . . . . . . . . . . . . . . . . . . . . . . 435,436,479 Oil Filter, Change . . . . . . . . . . . . . . . . . . . . . . . . 437 Oil Filter, Selection . . . . . . . . . . . . . . . . . . . . . . . 437 Onboard Diagnostic System . . . . . . . . . . . . . . 430,431 Opener, Garage Door (HomeLink威) . . . . . . . . . . . 185 Operating Precautions . . . . . . . . . . . . . . . . . . . . 430 Operator Manual (Owner’s Manual) .
PAGE 528
526 INDEX Preparation for Jacking . . . . . . . . . . . . . . . . . . . . 408 Pretensioners Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Programmable Electronic Features . . . . . . . . . . . . 236 Programming Transmitters (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 20 Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . . 360 Radiator Cap (Coolant Pressure Cap) . . . . . . . . . . 448 Radio Operation . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 529
INDEX 527 Resetting Oil Change Indicator . . . . . . . . . . . 211,227 Restraint, Head . . . . . . . . . . . . . . . . . . . . . . . . . 130 Restraints, Child . . . . . . . . . . . . . . . . . . . . . . . . . 68 Restraints, Occupant . . . . . . . . . . . . . . . . . . . . . . 43 Rocking Vehicle When Stuck . . . . . . . . . . . . . . . . 420 Rotation, Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 368 Safety Checks Inside Vehicle . . . . . . . . . . . . . . . . .
PAGE 530
528 INDEX Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Rear Folding . . . . . . . . . . . . . . . . . . . . . . . . . 133 Reclining . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 Seatback Release . . . . . . . . . . . . . . . . . . . . . . . 133 Tilting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Security Alarm (Theft Alarm) . . . . . . . . . . . . . 18,217 Selection of Coolant (Antifreeze) . . . . . . . . . . 446,481 Selection of Oil . . . . . . .
PAGE 531
INDEX 529 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 481 Speed Control (Cruise Control) . . . . . . . . . . . 154,157 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 210 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27,313 Emergency (Jump Starting) . . . . . . . . . . . . . . . 417 Engine Fails to Start . . . . . . . . . . . . . . . . . . . . 316 Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Starting and Operating . . .
PAGE 532
530 INDEX Tire and Loading Information Placard . . . . . . . . . 353 Tire Identification Number (TIN) . . . . . . . . . . . . . 352 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . 348 Tire Safety Information . . . . . . . . . . . . . . . . . . . . 348 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81,357,508 Aging (Life of Tires) . . . . . . . . . . . . . . . . . . . . 363 Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 357 Chains . . . . . . . . . . . . .
PAGE 533
INDEX 531 Recreational . . . . . . . . . . . . . . . . . . . . . . . . . . 401 Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393 Towing Assistance . . . . . . . . . . . . . . . . . . . . . . . 108 Towing Vehicle Behind a Motor Home . . . . . . . . . 401 Traction Control . . . . . . . . . . . . . . . . . . . . . . . . . 343 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . 389 Cooling System Tips . . . . . . . . . . . . . . . . . . . . 401 Hitches . . . . . . . . . . .
PAGE 534
532 INDEX Uniform Tire Quality Grades . . . . . . . . . . . . . . . . 508 Universal Consumer Interface (UCI) Connector . . . 282 Universal Transmitter . . . . . . . . . . . . . . . . . . . . . 185 Unleaded Gasoline . . . . . . . . . . . . . . . . . . . . . . . 379 Untwisting Procedure, Seat Belt . . . . . . . . . . . . . . 50 Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Variance, Compass . . . . . . . . . . . . . . . . . . . . . . . 234 Vehicle Certification Label . . . . . . . .
PAGE 535
INDEX 533 Windshield Washers . . . . . . . . . . . . . . . . . . . 147,148 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 442 Windshield Wiper Blades . . . . . . . . . . . . . . . . . . 441 Windshield Wipers . . . . . . . . . . . . . . . . . . . . . . . 147 Wiper Blade Replacement . . . . . . . . . . . . . . . . . . 441 Wipers, Intermittent . . . . . . . . . . . . . . . . . . . . . . 147 Wipers, Rain Sensitive . . . . . . . . . . . . . . . . . . . .
PAGE 536
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
PAGE 537
Chrysler LLC 81-026-0943 First Edition Printed in U.S.A.