2013 Compass 2013 OWNER’S MANUAL Chrysler Group LLC 13MK49-126-AA First Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I nf or mat i onPr ov i dedby :
INTRODUCTION CONTENTS 䡵 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 WARNINGS AND CAUTIONS . . . . . . . . . . . . . .7 䡵 ROLLOVER WARNING . . . . . . . . . . . . . . . . . . .4 䡵 VEHICLE IDENTIFICATION NUMBER . . . . . . . .7 䡵 HOW TO USE THIS MANUAL . . . . . . . . . . . . . .5 䡵 VEHICLE MODIFICATIONS/ALTERATIONS . . . .
4 INTRODUCTION When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained techCongratulations on selecting your new Chrysler Group nicians and genuine MOPAR威 parts, and cares about LLC vehicle. Be assured that it represents precision your satisfaction. workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
INTRODUCTION 5 control. Failure to operate this vehicle safely may result seat belts could cut the highway death toll by 10,000 or in a collision, rollover of the vehicle, and severe or fatal more each year and could reduce disabling injuries by two million annually. In a rollover crash, an unbelted injury. Drive carefully. person is significantly more likely to die than a person wearing a seat belt. Always buckle up.
6 INTRODUCTION I nf or mat i onPr ov i dedby :
INTRODUCTION 7 WARNINGS AND CAUTIONS 1 This Owners Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information. Observe all Warnings and Cautions.
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right Front Body VIN Location NOTE: It is illegal to remove or alter the VIN.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A WORD ABOUT YOUR KEYS . . . . . . . . . . . . . .12 ▫ Rearming The System . . . . . . . . . . . . . . . . . . .19 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .12 ▫ To Disarm The System . . . . . . . . . . . . . . . . . . .19 ▫ Locking Doors With A Key. . . . . . . . . . . . . . . .14 ▫ Vehicle Security Alarm Manual Override . . . . . .19 ▫ Key-In-Ignition Reminder. . . . . . . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Sound Horn With Remote Key Lock . . . . . . . . .22 䡵 POWER WINDOWS — IF EQUIPPED . . . . . . . .35 ▫ Flash Lights With Remote Key Lock/Unlock . . .23 ▫ Power Window Switches . . . . . . . . . . . . . . . . .35 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .24 ▫ Auto-Down . . . . . . . . . . . . . . . . . . . . . . . . . .36 ▫ Programming Additional Transmitters. . . . . . . .24 ▫ Window Lockout Switch . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Energy Management Feature . . . . . . . . . . . . . .54 ▫ Event Data Recorder (EDR) . . . . . . . . . . . . . . .75 ▫ Seat Belt Pretensioners . . . . . . . . . . . . . . . . . .55 ▫ Child Restraints . . . . . . . . . . . . . . . . . . . . . . .76 ▫ Supplemental Active Head Restraints 䡵 ENGINE BREAK-IN RECOMMENDATIONS . . . .96 (AHR) — If Equipped . . . . . . . . . . . . . . . . . . .55 䡵 SAFETY TIPS . . . . . . . . . . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key Removal The authorized dealer that sold you your new vehicle has 1. Place the shift lever in PARK (if equipped with an the key code numbers for your vehicle locks. These automatic transmission). numbers can be used to order duplicate keys. Ask your authorized dealer for these numbers and keep them in a 2. Turn the ignition switch to the ACC (Accessory) position. safe place. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: If you try to remove the key before you place the shift lever in PARK, the key may become trapped temporarily in the ignition switch cylinder. If this occurs, place the shift lever in PARK, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) CAUTION! • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever. • Do not leave the Key Fob in or near the vehicle, and do not leave the ignition in the ACC or ON/RUN position. A child could operate power windows, other controls, or move the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 SENTRY KEY姞 The Sentry Key威 Immobilizer System prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses ignition keys that have an embedded electronic chip (transponder) to prevent unauthorized vehicle operation.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! CAUTION! The Sentry Key威 Immobilizer system is not compatible with some after-market remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. Always remove the Sentry Keys威 from the vehicle and lock all doors when leaving the vehicle unattended.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 4. Insert a blank Sentry Key威 into the ignition switch. Turn the ignition switch to the ON/RUN position If you have two valid Sentry Keys威, you can program within 60 seconds. After 10 seconds, a single chime new Sentry Keys威 to the system by performing the will sound. In addition, the Vehicle Security Light will following procedure: stop flashing. To indicate that programming is com1.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE authorized dealer at the time of service to be repro- sound, the headlights, park lamps and/or turn signals will flash repeatedly for three minutes. If the disturbance grammed. is still present (driver’s door, passenger door, other doors, General Information ignition) after three minutes, the parking lights and tail The Sentry Key威 system complies with FCC rules Part 15 lights will flash for an additional 15 minutes. and with RSS-210 of Industry Canada.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 Alarm will automatically disarm. After approximately 16 seconds, the Vehicle Security Light will flash slowly. This shows that the Vehicle Security Alarm is fully armed. Rearming The System If something triggers the alarm, and no action is taken to disarm it, the Vehicle Security Alarm will turn off the horn after three minutes, turn off all of the visual signals after 15 minutes, and then the Vehicle Security Alarm will rearm itself.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The line of transmission must not be blocked This system allows you to lock or unlock the doors and with metal objects. liftgate or activate the Panic Alarm from distances up to To Unlock The Doors And Liftgate approximately 66 ft (20 m) using a hand-held Remote Press and release the UNLOCK button on the RKE Keyless Entry (RKE) transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 • 1. 2. 3. (Customer-Programmable Features)” in “Understand- NOTE: Pressing the LOCK button on the RKE transmiting Your Instrument Panel” for further information. ter while you are inside the vehicle will activate the Vehicle Security Alarm. Opening a door with the Vehicle For vehicles not equipped with the EVIC, perform the Security Alarm activated will cause the alarm to sound.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Lock The Doors And Liftgate • For vehicles not equipped with the EVIC, perform the following steps: Press and release the LOCK button on the RKE transmitter to lock all doors and liftgate. The turn signal lights 1. Press the LOCK button on a programmed RKE transwill flash and the horn will chirp to acknowledge the mitter for at least 4 seconds, but no longer than 10 signal. seconds. Then, press the PANIC button while still holding the LOCK button.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 UNLOCK button to deactivate the Vehicle Security Alarm. Flash Lights With Remote Key Lock/Unlock than 10 seconds. Then, press and hold the LOCK button while still holding the UNLOCK button. 2. Release both buttons at the same time. This feature will cause the turn signal lights to flash when 3. Test the feature while outside of the vehicle by pressthe doors are locked or unlocked with the RKE transmiting the LOCK/UNLOCK buttons on the RKE transter.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using The Panic Alarm General Information To turn the Panic Alarm feature ON or OFF, press and hold the PANIC button on the RKE transmitter for at least one second and release. When the Panic Alarm is on, the headlights and park lights will flash, the horn will pulse on and off and the interior lights will turn on. This device complies with Part 15 of FCC rules and with RS-210 of Industry Canada.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, military base, and some mobile or CB radios. 2 Transmitter Battery Replacement NOTE: Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate The recommended replacement battery is CR2032. 1. If the RKE transmitter is equipped with a screw, remove the screw.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the RKE transmitter is equipped with a screw, How To Use Remote Start reinstall and tighten the screw until snug. All of the following conditions must be met before the engine will remote start: REMOTE STARTING SYSTEM — IF EQUIPPED • Shift lever in PARK This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conveniently from outside the vehicle while still maintaining security.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 • Remote Start Aborted — Hood Ajar WARNING! • Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Monoxide (CO) which is odorless and colorless. Carbon Monoxide is poisonous and can cause serious injury or death when inhaled. • Keep Remote Keyless Entry (RKE) transmitters away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Low Fuel Light turns on NOTE: • The park lamps will turn on and remain on during • Remote Start mode. • • For security, power window and power sunroof op• eration (if equipped) are disabled when the vehicle is in the Remote Start mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 To Exit Remote Start Mode And Drive The Vehicle Before the end of the 15-minute cycle, press and release the UNLOCK button on the RKE transmitter to unlock the doors and disarm the Vehicle Security Alarm (if equipped). Then, insert the key into the ignition switch and turn the switch to the ON/RUN position. 2 NOTE: The ignition switch must be in the ON/RUN position in order to drive the vehicle.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) CAUTION! • Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, and remove the Key Fob from the ignition. When leaving the vehicle, always lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 auto door lock feature can be enabled or disabled by your authorized dealer. Please see your authorized dealer for service.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Within 15 seconds, cycle the ignition switch between Automatic Unlock Doors On Exit LOCK and ON/RUN and then back to LOCK four The doors will unlock automatically if: times ending up in the LOCK position (do not start the • The Automatic Unlock Doors On Exit feature is enengine). abled. 3. Within 30 seconds, press the power door LOCK switch • The transmission was in gear and the vehicle speed to lock the doors. returned to 0 mph (0 km/h). 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Equipped/Personal Settings (Customer- NOTE: Programmable Features)” in “Understanding Your In• If you do not hear the chime it means that the system strument Panel” for further information. did not enter the programming mode and you will need to repeat the procedure. • For vehicles not equipped with the EVIC, perform the following procedure: • Use the Automatic Unlock Doors On Exit feature in accordance with local laws. 1.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Repeat steps 1 and 2 for the opposite rear door. Child-Protection Door Lock Function Child-Protection Door Lock Location WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the Child-Protection locks are engaged.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 NOTE: For emergency exit with the system engaged, NOTE: move the lock knob up (unlocked position), roll down the • For vehicles not equipped with the Electronic Vehicle window and open the door with the outside door handle. Information Center (EVIC), the power window switches will remain active for 45 seconds after the POWER WINDOWS — IF EQUIPPED ignition switch is turned to the LOCK position.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. Power Window Switch Location Auto-Down The driver’s door window switch has an Auto-Down feature. Push the window switch past the first detent, release, and the window will go down automatically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Window Lockout Switch LIFTGATE The window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window LOCKOUT switch. To enable the window controls, press the window LOCKOUT switch a second time. NOTE: The key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Once unlocked, the liftgate can be opened or closed NOTE: without using the key. To open the liftgate, squeeze the • In the event of a power malfunction, or the RKE liftgate release and pull the liftgate open with one fluid transmitter is inoperative, insert the key into the motion. liftgate lock cylinder and turn to the right (manual lock models only). Using the liftgate handle, pull the liftgate open with one fluid motion.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 OCCUPANT RESTRAINTS WARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • If you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. Do not use the recirculation mode.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Knee bolsters for front seat occupants If you will be carrying children too small for adult-sized seat belts, the seat belts or the Lower Anchors and Tether • Front seat belts incorporate pretensioners that may for CHildren (LATCH) feature also can be used to hold enhance occupant protection by managing occupant infant and child restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 You should read the instructions provided with your child restraint to make sure that you are using it properly. WARNING! Infants in rear facing child restraints should never ride in the front seat of a vehicle with a passenger Advanced Front Air Bag. An air bag deployment can cause severe injury or death to infants in that position. 2. All occupants should always wear their lap and shoulder belts properly. 3.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won’t deploy at all. Always wear your seat belts even though you have air bags. • Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions in your vehicle are equipped with lap/shoulder belts.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. • Two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind you will not protect you from injury during a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt may not protect you properly. In a collision, it could even cut into you. Be sure the belt is straight.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front seat, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push the anchorage button to release the anchorage, and move it up or down to the position that fits you best. NOTE: The adjustable upper shoulder belt anchorage is equipped with an Easy Up feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 In the rear seat, move toward the center of the seat to position the belt away from your neck. Second Row Center Lap/Shoulder Belt Operating Instructions 2 The second row center lap/shoulder belt features a three-point seat belt with a mini-latch and buckle, which allows the shoulder belt to detach from the lower anchor when the seat is folded.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Route the shoulder belt to the inside of the right head 5. Sit back in the seat. Slide the regular latch plate up the restraint. webbing as far as necessary to allow the belt to go around your lap. 6. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Routing The Rear Center Shoulder Belt 4. When the belt is long enough to fit, insert the minilatch plate into the mini-buckle until you hear a “click.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 7. Position the lap belt across your thighs, below your 8. Position the shoulder belt on your chest so that it is abdomen. To remove slack in the lap belt portion, pull comfortable and not resting on your neck. The retracup on the shoulder belt. To loosen the lap belt if it is tor will withdraw any slack in the belt. too tight, pull on the lap belt. A snug belt reduces the 9. To release the belt, push the red button on the buckle.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 10. To disengage the mini-latch from the mini-buckle for 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of storage, insert the regular latch plate into the black the latch plate. button on the top of the mini-buckle. The belt will automatically retract to its stowed position. If neces4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 • N/A — Not Applicable the shoulder belt. The Automatic Locking Mode is available on all passenger-seating positions with a combina• ALR — Automatic Locking Retractor tion lap/shoulder belt. Use the Automatic Locking Mode If the passenger seating position is equipped with an anytime a child safety seat is installed in a seating ALR and is being used for normal usage: position that has a belt with this feature.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Disengage The Automatic Locking Mode Energy Management Feature Unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the Automatic Locking Mode and activate the vehicle sensitive (emergency) locking mode. This vehicle has a safety belt system with an Energy Management feature in the front seating positions to help further reduce the risk of injury in the event of a head-on collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Seat Belt Pretensioners Supplemental Active Head Restraints (AHR) — If The seat belts for both front seating positions are Equipped equipped with pretensioning devices that are designed to These head restraints are passive, deployable comporemove slack from the seat belt in the event of a collision.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When AHRs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the AHR. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear impacts. NOTE: The Active Head Restraints (AHR) may or may not deploy in the event of a front or side impact.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 1. Grasp the deployed AHR from the rear seat. CAUTION! All occupants, including the driver, should not operate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. 3 — Final Downward Movement To Engage Locking Mechanism 1 — Downward Movement 2 — Rearward Movement 4. The AHR front soft foam and trim half should lock into the back decorative plastic half.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Enhanced Seat Belt Use Reminder System (BeltAlert姞) BeltAlert威 is a feature intended to remind the driver and front passenger (if equipped with front passenger BeltAlert威) to fasten their seat belts. The feature is active whenever the ignition is on. If the driver or front seat passenger is unbelted, the Seat Belt Reminder Light will turn on and remain on until both front seat belts are fastened.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE unbuckled while traveling at speeds greater than 5 mph Seat Belt Extender (8 km/h), BeltAlert威 will provide both audio and visual If a seat belt is too short even when fully extended and notification. when the adjustable upper shoulder belt anchorage (if The front passenger seat BeltAlert威 is not active when the equipped) is in its lowest position, your authorized front passenger seat is unoccupied.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Seat Belts And Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. 2 Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Advanced Front Air Bags have a multistage inflator design. This allows the air bag to have different rates of inflation that are based on the severity and type of collision. This vehicle may be equipped with Supplemental SeatMounted Side Air Bags (SAB) to provide enhanced protection for an occupant during a side impact. The Supplemental Seat-Mounted Side Air Bags are located in the outboard side of the front seats.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 • Instrument Panel The first stage inflator is triggered immediately during an impact that requires air bag deployment. This low output is used in less severe collisions. A higher energy output is used for more severe collisions.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional. The protective covers for the air bag cushions are designed to open only when the air bags are inflating. • Do not drill, cut or tamper with the knee bolster in any way.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each air bag deploys independently; a left side impact deploys the left air bag only and a right-side impact deploys the right air bag only. Supplemental Side Air Bag Inflatable Curtain (SABIC) SABIC air bags may offer side-impact and vehicle rollover protection to front and rear seat outboard occupants in addition to that provided by the body structure.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Air Bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • Being too close to the Supplemental Side Air Bag Inflatable Curtain and/or Seat-Mounted Side Air Bag during deployment could cause you to be severely injured or killed. The system includes side impact sensors that are calibrated to deploy the side air bags during impacts that require air bag occupant protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 windows, or area where the SAB or SABIC air bags Air Bag Deployment Sensors And Controls inflate, even if they are in an infant or child restraint. Occupant Restraint Controller (ORC) Always sit upright as possible with your back against the The ORC is part of a Federally regulated safety system seat back, use the seat belts properly, and use the required for this vehicle.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE including the severity and type of collision. Advanced Seat belts are necessary for your protection in all colliFront Air Bags are not expected to reduce the risk of sions, and also are needed to help keep you in position, away from an inflating air bag. injury in rear, side, or rollover collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 turns on the Air Bag Warning Light, either momentarily Driver And Passenger Advanced Front Air Bag or continuously. A single chime will sound if the light Inflator Units comes on again after initial startup.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Advanced Front Air Bag gas is vented through the you if you are not seated properly, or if items are vent holes in the sides of the air bag. In this way, the air positioned in the area where the side air bag inflates. This especially applies to children. bags do not interfere with your control of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 inflates. This especially applies to children. The side event the ORC will determine whether to have the curtain air bag is only about 3-1/2 in (9 cm) thick when Enhanced Accident Response System perform the following functions: it is inflated. Because air bag sensors estimate deceleration over time, • Cut off fuel to the engine.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system. If you do have a collision, which deploys the air bags, any or all of the following may occur: bag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Maintaining Your Air Bag System WARNING! (Continued) WARNING! • Modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag Warning Light • The Air Bag Warning Light remains on after the four to eight second interval. You will want to have the air bags ready to inflate for your protection in a collision. The Air Bag Warning Light monitors the internal circuits and interconnecting wiring associated with air bag system electrical components.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 These data can help provide a better understanding of This vehicle is equipped with an event data recorder the circumstances in which crashes and injuries occur. (EDR).
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Everyone in your vehicle needs to be buckled up at all Standards. You should also make sure that you can install times, including babies and children. Every state in the it in the vehicle where you will use it. United States, and every Canadian province, requires that small children ride in proper restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Summary Of Recommendations For Restraining Children In Vehicles Infants and Toddlers Small Children Larger Children Children Too Large for Child Restraints Child Size, Height, Weight or Age Children who are two years old or younger and who have not reached the height or weight limits of their child restraint Children who are at least two years old or who have out-grown the height or weight limit of their rear-facing child restraint Children who have out-g
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE their infant carrier but are still less than at least two years old. Children should remain rearward-facing until they Safety experts recommend that children ride rearwardreach the highest weight or height allowed by their facing in the vehicle until they are two years old or until convertible child seat. they reach either the height or weight limit of their rear facing child safety seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Older Children And Child Restraints Children who are two years old or who have outgrown their rear-facing convertible child seat can ride forwardfacing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who are over two years old or who have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Is the lap part of the belt as low as possible, touching the child’s thighs and not their stomach? Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend 5. Can the child stay seated like this for the whole trip? over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Recommendations For Attaching Child Restraints Restraint Type Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Combined Weight of the Child + Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors and Tethers for Children (LATCH) Restraint System Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCHequipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 LATCH Positions For Installing Child Restraints In This Vehicle 2 Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol I nf or mat i onPr ov i dedby :
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Can two child restraints be attached using a common lower LATCH anchorage? No Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the head restraints be removed? No I nf or mat i onPr ov i dedby : Never “share” a LATCH anchorage with two or more child restraints.
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating The LATCH Anchorages Locating The LATCH Anchorages The lower anchorages are round bars that are In addition, there are tether strap anchorages found at the rear of the seat cushion where it behind each rear seating position located on meets the seatback. They are just visible when the back of the seat. you lean into the rear seat to install the child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 restraints with flexible, webbing mounted lower attach- To Install A LATCH-compatible Child Restraint ments can be installed in any rear seating position. 1. If the selected seating position has a Switchable Automatic Locking Retractor (ALR) seat belt, stow the seat WARNING! belt, following the instructions below.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Attach the lower hooks or connectors of the child How To Stow An Unused ALR Seatbelt restraint to the lower anchorages in the selected seat- When using the LATCH attaching system to install a ing position. child restraint, stow all ALR seat belts that are not being 5. If the child restraint has a tether strap, connect it to the used by other occupants or being used to secure child top tether anchorage. See the section “Installing Child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 the seat belt tight around the child restraint so that it is not necessary to use a locking clip. The ALR retractor can Improper installation of a child restraint to the be “switched” into a locked mode by pulling all of the LATCH anchorages can lead to failure of the re- webbing out of the retractor and then letting the webbing straint. The child could be badly injured or killed. retract back into the retractor.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Systems for Installing Child Restraints in this Vehicle I nf or mat i onPr ov i dedby :
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 What is the weight limit (child’s weight + weight of the child restraint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? Can the rear-facing child restraint touch the back of the front passenger seat? Weight limit of the Child Restraint Can the head restraints be removed? Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint? No Yes Yes Always use the tether anchor
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing A Child Restraint with a Switchable Automatic Locking Retractor (ALR) back into the retractor. As the webbing retracts, you will hear a clicking sound. This means the seat belt is now in the Automatic Locking mode. 1. Place the child seat in the center of the seating position. For some second row seats, you may need to 6. Try to pull the webbing out of the retractor.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 9. Test that the child restraint is installed tightly by 3. Slide the latch plate into the buckle until you hear a “click.” pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) 4. Finally, pull up on any excess webbing to tighten the in any direction.
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Any seat belt system will loosen with time, so check the Installing Child Restraints Using The Top Tether belt occasionally, and pull it tight if necessary. Anchorage If the buckle or the cinching latch plate is too close to the 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. If your vehicle is equipped with a split rear seat, make sure the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. Transporting Pets Tether Anchorage Locations 4.
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS CAUTION! A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or NOTE: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 Exhaust Gas WARNING! • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 Air Bag Warning Light Floor Mat Safety Information The light should come on and remain on for four to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Defroster Check operation by selecting the defrost mode and place the blower control on high speed.
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfering with the pedals or the ability to control the vehicle. • Never put floor mats or other floor coverings on top of already installed floor mats. Additional floor mats and other coverings will reduce the size of the pedal area and interfere with the pedals.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 Periodic Safety Checks You Should Make Outside The Vehicle Door Latches Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Check the wheel nuts for tightness. Check the tires (including spare) for proper cold inflation pressure.
I nf or mat i onPr ov i dedby :
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 䡵 Uconnect™ Phone — IF EQUIPPED . . . . . . . . .112 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . .107 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .114 ▫ Automatic Dimming Mirror — If Equipped . . .108 ▫ Phone Call Features . . . . . . . . . . . . . . . . . . . .121 ▫ Outside Mirror — Driver Side . . . . . . . . . . . .109 ▫ Uconnect™ Phone Features .
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Commands . . . . . . . . . . . . . . . . . . . . . . . . . .144 ▫ Reclining Rear Seat — If Equipped . . . . . . . . .159 ▫ Voice Training . . . . . . . . . . . . . . . . . . . . . . . .147 䡵 TO OPEN AND CLOSE THE HOOD . . . . . . . . .160 䡵 SEATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148 䡵 LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .162 ▫ Power Seats — If Equipped . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 䡵 WINDSHIELD WIPERS AND WASHERS . . . . . .168 ▫ To Accelerate For Passing . . . . . . . . . . . . . . . .175 ▫ Windshield Wiper Operation . . . . . . . . . . . . .169 䡵 GARAGE DOOR OPENER — IF EQUIPPED . . .176 ▫ Intermittent Wiper System . . . . . . . . . . . . . . .170 ▫ Before You Begin Programming HomeLink威. . .177 ▫ Windshield Washers . . . . . . . . . . . . . . . . . . .170 ▫ Programming A Rolling Code . . . . . . . . . . . . .178 ▫ Mist Feature .
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Closing Sunroof — Express. . . . . . . . . . . . . . .186 ▫ Door Storage . . . . . . . . . . . . . . . . . . . . . . . . .195 ▫ Closing Sunroof — Manual Mode . . . . . . . . . .186 䡵 CONSOLE FEATURES . . . . . . . . . . . . . . . . . . .196 ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . . .186 䡵 CARGO AREA FEATURES . . . . . . . . . . . . . . . .197 ▫ Venting Sunroof — Express . . . . . . . . . . . . . .187 ▫ Sunshade Operation. . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. 3 Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated. The sensor to the right of the button does not illuminate. NOTE: This feature is disabled when the vehicle is moving in reverse.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Outside Mirror — Driver Side WARNING! Adjust the flat outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle with your head close to the door glass. Outside Mirror — Passenger Side Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle with your head close to the center of the vehicle.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When you are finished adjusting the mirror, turn the control to the center position to prevent accidentally The power mirror control is located on the driver’s door moving a mirror. trim panel. Power Mirrors WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “Rear Window Features” in “Understanding the Features of Your Vehicle” for further information. 3 Vanity Mirrors — If Equipped To use the vanity mirror, rotate the sun visor down and swing the mirror cover upward.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect™ Phone — IF EQUIPPED • www.jeep.com/uconnect Uconnect™ Phone is a voice-activated, hands-free, invehicle communications system. Uconnect™ Phone allows you to dial a phone number with your mobile phone using simple voice commands (e.g., “Call” ѧ “Mike” ѧ “Work” or “Dial” ѧ “248-555-1212”). Your mobile phone’s audio is transmitted through your vehicle’s audio system; the system will automatically mute your radio when using the Uconnect™ Phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 used with the system at a time. The system is available in access the system. When you press the button you will hear the word Uconnect™ followed by a BEEP. The beep English, Spanish, or French languages. is your signal to give a command. WARNING! Voice Command Button Any voice commanded system should be used only in safe driving conditions following all applicable laws, including laws regarding phone use. All attention should be kept on the roadway ahead.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The radio display will be used for visual prompts from • For each feature explanation in this section, only the compound form of the voice command is given. You the Uconnect™ Phone such as “CELL” or caller ID on can also break the commands into parts and say each certain radios. part of the command when you are asked for it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 To activate the Uconnect™ Phone, simply press the The following are general phone to Uconnect™ Phone button and follow the audible prompts for direc- pairing instructions: tions. Uconnect™ Phone sessions begin with a press of • Press the button to begin. button on the radio control head. the • After the “Ready” prompt and the following beep, say Cancel Command “Device Pairing”.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will then be asked to give your mobile phone a priority level between one and seven, with one being the highest priority. You can pair up to seven mobile phones to your Uconnect™ Phone. However, at any given time, only one mobile phone can be in use, connected to your Uconnect™ System. The priority allows the Uconnect™ Phone to know which mobile phone to use if multiple mobile phones are in the vehicle at the same time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 or downloaded phonebook. To learn how to store a • When prompted, enter the number designation (e.g., “Home”, “Work”, “Mobile”, or “Other”). This will name in the phonebook, refer to “Add Names to Your allow you to store multiple numbers for each phoneUconnect™ Phonebook”, in the phonebook. book entry, if desired.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Depending on the maximum number of entries downloaded, there may be a short delay before the latest downloaded names can be used. Until then, if availIf equipped and specifically supported by your phone, able, the previously downloaded phonebook is availUconnect™ Phone automatically downloads names (text able for use. names) and number entries from your mobile phone’s phonebook.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in NOTE: the phonebook, call the number you just edited, or return • Editing names in the phonebook is recommended to the main menu. when the vehicle is not in motion. “Phonebook Edit Entry” can be used to add another • Automatic downloaded phonebook entries cannot be phone number to a name entry that already exists in the phonebook.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say “List Names” to hear a list of the entries in the phonebook from which you choose. To select one of the entries button while the from the list, press the Uconnect™ Phone is playing the desired entry and say “Delete”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 • After the “Ready” prompt and the following beep, say mobile service plan. For example, if your mobile service plan provides three-way calling, this feature can be “Phonebook List Names”. accessed through the Uconnect™ Phone. Check with • The Uconnect™ Phone will play the names of all the your mobile service provider for the features that you phonebook entries, including the downloaded phonehave. book entries, if available.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE button to place the current Place/Retrieve A Call From Hold mobile phone. Press the call on hold and answer the incoming call. To put a call on hold, press the button until you hear NOTE: The Uconnect™ Phone compatible phones in the a single beep. This indicates that the call is on hold. To butmarket today do not support rejecting an incoming call bring the call back from hold, press and hold the when another call is in progress.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Three-Way Calling Redial To initiate three-way calling, press the button while • Press the button to begin. a call is in progress, and make a second phone call, as • After the “Ready” prompt and the following beep, say described under “Making a Second Call While Current “Redial”. Call is in Progress”.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ends, or until the vehicle battery condition dictates • After the “Ready” prompt and the following beep, say the name of the language you wish to switch to cessation of the call on the Uconnect™ Phone and English, Espanol, or Francais. transfer of the call to the mobile phone. • After the ignition key is switched to OFF, a call can • Continue to follow the system prompts to complete the language selection.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 If the phone is not reachable and the Uconnect™ Phone is • If supported, this number may be programmable on some systems. To do this, press the button and say operational, you may reach the emergency number as “Setup”, followed by “Emergency”. follows: • The Uconnect™ Phone does slightly lower your chances of successfully making a phone call as to that • After the “Ready” prompt and the following beep, say for the mobile phone directly.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the “Ready” prompt and the following beep, say certain companies, which time out a little too soon to work properly with the Uconnect™ Phone. “Roadside Assistance”. NOTE: Voice Mail Calling • The roadside assistance number dialed is based on the country where the vehicle is purchased (1-800-5282069 for the U.S., 1-877-213-4525 for Canada, 55-143454 for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 on your mobile phone keypad, you can press the button and say the sequence you wish to enter, followed by the word “Send”. For example, if required to enter your PIN followed with a pound, (3 7 4 6 #), you button and say, “3 7 4 6 # Send”. can press the Saying a number, or sequence of numbers, followed by “Send”, is also to be used for navigating through an automated customer service center menu structure, and to leave a number on a pager.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning Confirmation Prompts ON/OFF using Uconnect™ Phone. The status is given for network signal strength, phone battery strength, etc. Turning confirmation prompts off will stop the system from confirming your choices (e.g., the Uconnect™ Dialing Using The Mobile Phone Keypad Phone will not repeat a phone number before you dial it). You can dial a phone number with your mobile phone keypad and still use the Uconnect™ Phone (while dialing button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 from your Uconnect™ Phone paired mobile phone to the Uconnect™ Phone or vice versa, press the button When you mute the Uconnect™ Phone, you will still be and say “Transfer Call”. able to hear the conversation coming from the other party, but the other party will not be able to hear you. In Connect Or Disconnect Link Between The order to mute the Uconnect™ Phone: Uconnect™ Phone And Mobile Phone Mute/Un-Mute (Mute ON/OFF) • Press the button.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The selected phone will be used for the next phone call. If the selected phone is not available, the • The Uconnect™ Phone will play the phone names of Uconnect™ Phone will return to using the highest all paired mobile phones in order from the highest to priority phone present in or near (approximately the lowest priority. To “Select” or “Delete” a paired within 30 ft (9 m)) the vehicle. button and say phone being announced, press the “Select” or “Delete”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Things You Should Know About Your Uconnect™ Phone Uconnect™ Phone Tutorial • Press the button and say the “Voice Training”, “System Training”, or “Start Voice Training” command. To hear a brief tutorial of the system features, press the You can either press the Uconnect™ Phone button to restore the factory setting or repeat the words and button and say “Uconnect™ Tutorial.” phrases when prompted by the Uconnect™ Phone.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This will delete all phone pairing, phone book entries, and other settings in all language modes. The System will prompt you before resetting to factory settings. Voice Command • low road noise, • smooth road surface, • fully closed windows, • dry weather condition.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 • Phonebook (Downloaded and Uconnect™ Phone Local) name recognition rate is optimized when the entries are not similar. • Numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight hundred”. • You can say “O” (letter “O”) for “0” (zero). • smooth road surface, • fully closed windows, • dry weather conditions, and • operation from the driver’s seat.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Send Messages: SMS Uconnect™ Phone can read or send new messages on You can send messages using Uconnect™ Phone. To send your phone. a new message: • Press the Read Messages: button. If you receive a new text message while your phone is • After the “Ready” prompt and the following beep, say connected to Uconnect™ Phone, an announcement will “SMS Send” or “Send Message.” be made to notify you that you have a new text message.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 List of Preset Messages: 11. See You in 15 minutes 1. Yes 12. I am on my way 2. No 13. I’ll be late 3. Where are you? 14. Are you there yet? 4. I need more direction. 15. Where are we meeting? 5. L O L 16. Can this wait? 6. Why 17. Bye for now 7. I love you 18. When can we meet? 8. Call me 19. Send number to call 9. Call me later 20. Start without me 10.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn SMS Incoming Announcement ON/OFF Bluetooth威 Communication Link Turning the SMS Incoming Announcement OFF will stop Mobile phones have been found to lose connection to the the system from announcing the new incoming mes- Uconnect™ Phone. When this happens, the connection can generally be reestablished by switching the phone sages. off/on. Your mobile phone is recommended to remain in button. • Press the Bluetooth威 ON mode.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 3 I nf or mat i onPr ov i dedby :
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE I nf or mat i onPr ov i dedby :
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 3 I nf or mat i onPr ov i dedby :
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Primary Alternate (s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all call Voice Commands Primary Alternate (s) cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home language list names I nf or mat i onPr ov i dedby :
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Voice Commands Primary Alternate (s) list phones mobile mute mute off new entry no other pair a phone phone pairing pairing phonebook phone book previous record again redial Voice Commands Primary Alternate (s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call Uconnect™ Tutorial try again voice training work yes I nf or mat i onPr ov i dedby : 3
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information VOICE COMMAND — IF EQUIPPED This device complies with Part 15 of the FCC rules and Voice Command System Operation RSS 210 of Industry Canada. Operation is subject to the following conditions: This Voice Command system allows you to control your AM, FM radio, satellite radio, disc • Changes or modifications not expressly approved by player, and a memo recorder.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 WARNING! Any voice commanded system should be used only in safe driving conditions following all applicable laws. All attention should be kept on the roadway ahead. Failure to do so may result in a collision causing serious injury or death. Pressing the Voice Command button while the system is speaking is known as “barging in.” The system will be interrupted, and after the beep, you can add or change commands.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To hear the first available Menu, press the Voice Com- Main Menu button and say “Help” or “Main Menu”. mand Start a dialogue by pressing the Voice Command button. You may say “Main Menu” to switch to the Commands main menu. The Voice Command system understands two types of commands. Universal commands are available at all In this mode, you can say the following commands: times.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 • “Previous Station” (to select the previous station) Satellite Radio • “Radio Menu” (to switch to the radio menu) To switch to satellite radio mode, say “Sat” or “Satellite Radio”. In this mode, you may say the following commands: • “Main Menu” (to switch to the main menu) Radio FM To switch to the FM band, say “FM” or “Radio FM”.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Disc – “Continue” (to continue recording) – “Delete” (to delete the recording) To switch to the disc mode, say “Disc”. In this mode, you may say the following commands: • “Play Memos” (to play previously recorded memos) — During the playback you may press the Voice Com• “Track” (#) (to change the track) mand button to stop playing memos.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 • “Change to setup” Voice Training • “Main menu setup” or For users experiencing difficulty with the system recognizing their voice commands or numbers the Uconnect™ Voice “Voice Training” feature may be used. • “Switch to setup” In this mode, you may say the following commands: • “Language English” • “Language French” • “Language Spanish” button, say “System 1. Press the Voice Command Setup” and once you are in that menu then say “Voice Training.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Power Seats — If Equipped Seats are a part of the Occupant Restraint System of the Some models may be equipped with a power driver’s vehicle. seat. The power seat switch is located on the outboard side of the seat near the floor. Use the switch to move the seat up, down, forward, rearward, or to tilt the seat. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Adjusting The Seat Forward Or Rearward WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt. CAUTION! The seat can be adjusted both forward and rearward.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE minutes of continuous operation. If LOW-level heating is selected, the system automatically turns the heater and On some models, the front driver and passenger seats the indicator light OFF after a maximum of 30 minutes of may be equipped with heaters in both the seat cushions continuous operation. and seatbacks. The controls for the front heated seats are located on the center instrument panel area.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 WARNING! (Continued) • Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat. 3 Manual Front Seat Adjustment On models equipped with manual seats, the adjusting bar is located at the front of the seats, near the floor.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 3 Lumbar Adjustment Lever Recline Lever Driver’s Seatback Recline WARNING! To adjust the seatback, lift the lever located on the outboard side of the seat, lean back to the desired angle and release the lever. To return the seatback, lift the lever, lean forward and release the lever. Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fold-Flat Front Passenger Seat To fold the front passenger seat, lift the recliner handle to the full upward position and push the seatback forward until it rests on the seat cushion. Fold-Flat Seat Head Restraints Fold-Flat Lever Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 WARNING! The head restraints for all occupants must be properly adjusted prior to operating the vehicle or occupying a seat. Head restraints should never be adjusted while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision. identified by any markings, only through visual inspection of the head restraint.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint. For comfort the Active Head Restraints can be tilted forward and backward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 • In the event of deployment of an Active Head Restraint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things To Know Before Starting Your Vehicle” for further information. WARNING! 3 • Do not place items over the top of the Active Head Restraint, such as coats, seat covers or portable DVD players.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat WARNING! (Continued) • Active Head Restraints may be deployed if they are struck by an object such as a hand, foot or loose cargo. To avoid accidental deployment of the Active Head Restraint ensure that all cargo is secured, as loose cargo could contact the Active Head Restraint during sudden stops. Failure to follow this warning could cause personal injury if the Active Head Restraint is deployed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 WARNING! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. Reclining Rear Seat — If Equipped Folded Rear Seat To raise the seatback, pull the strap forward and lift the seatback into its upright position.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only with the vehicle is parked. TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. 1. Pull the hood release lever located on the left kick panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 2. Move the safety latch, located outside the vehicle Lift the hood prop rod, clipped to the right side (left side under the front edge of the hood, toward the center facing hood) of the engine compartment to secure the and raise the hood. hood in the open position. Place the hood prop at the location stamped into the inner hood surface.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 8 in (20 cm) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Headlights And Parking Lights Daytime Running Lights — If Equipped Turn the end of the multifunction lever to the first detent The high beam lights will come on as Daytime Running to turn on the parking lights. Turn the end of the lever to Lights (lower intensity), whenever the ignition is ON, the the second detent to turn on the headlights.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The fog lights will only operate with the headThe front fog light switch is on the multifunction lights on low beam. Selecting high beam headlights will lever. To activate the front fog lights, turn on the turn off the fog lights. parking lights or the low beam headlights and pull out Turn Signals the end of the multifunction lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. High/Low Beam Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever toward you to switch the headlights back to low beam.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Instrument Panel Dimming Rotate the center portion of the lever to the extreme bottom position to fully dim the instrument panel lights and prevent the interior lights from illuminating when a door is opened. Rotate the center portion of the lever up to increase the brightness of the instrument panel lights when the parking lights or headlights are on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Map/Reading Lights These lights are mounted between the sun visors above the rear view mirror. Each light is turned on by pressing the button. Press the button a second time to turn the light off. The lights also come on when a door is opened or the dimmer control is turned fully upward, past the second detent.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever. For information on the rear wiper/washer, refer to “Rear Window Features” in “Understanding The Features Of Your Vehicle”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Windshield Wiper Operation CAUTION! • Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • In cold weather, always turn off the wiper switch and allow the wipers to return to the “Park” position before turning off the engine.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System Windshield Washers Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. Select the delay interval by turning the end of the lever. Rotate the end of the lever upward (clockwise) to decrease the delay time and downward (counterclockwise) to increase the delay time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Mist Feature Push down on the control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. 3 NOTE: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to spray the windshield with washer fluid.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Push down on the lever to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Push the lever up to lock the steering column firmly in place. WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Electronic Speed Control Buttons 1 — ON/OFF 4 — CANCEL 2 — RES + 3 — SET - Push the ON/OFF button.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it. To Set A Desired Speed vehicle will deactivate Electronic Speed Control without erasing the set speed memory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 To decrease speed while the Electronic Speed Control is set, push the SET (-) button. If the button is continually held in the SET (-) position, the set speed will continue to decrease until the button is released. Release the button when the desired speed is reached, and the new set speed will be established. Pressing the SET (-) button once will result in a 1 mph (1.6 km/h) decrease in set speed.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED HomeLink威 replaces up to three hand-held transmitters that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink威 unit is powered by your vehicles 12 Volt battery. The HomeLink威 buttons, located on either the overhead console, headliner or sunvisor, designate the three different HomeLink威 channels. The HomeLink威 indicator is located above the center button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 For more efficient programming and accurate transmission of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink威 system. Erase all channels before you begin programming. To erase the channels place the ignition in the ON/RUN position and press and hold the two outside HomeLink威 buttons (I and III) for up 20 seconds or until the red indicator flashes.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming A Rolling Code For programming garage door openers that were manufactured after 1995. These garage door openers can be identified by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the garage door opener. It is NOT the button that is normally used to open and close the door. The name and color of the button may vary by manufacturer. Training The Garage Door Opener 1 — Door Opener 2 — Training Button 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink威 button you wish to program while keeping the HomeLink威 indicator light in view. Firmly press and release the “LEARN” or “TRAINING” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the LEARN/TRAIN mode. 3.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink威 button you wish to proTo reprogram a channel that has been previously trained, gram while keeping the HomeLink威 indicator light in follow these steps: view. 1. Turn the ignition switch to the ON/RUN position. 3. Simultaneously press and hold both the Homelink威 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 • To program the two remaining HomeLink威 buttons, Canadian/Gate Operator Programming repeat each step for each remaining button. DO NOT For programming transmitters in Canada/United States erase the channels. that require the transmitter signals to “time-out” after several seconds of transmission.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink威 button you wish to program while keeping the HomeLink威 indicator light in view. • If the indicator light stays on constantly, programming is complete and the garage door/device should activate when the HomeLink威 button is pressed. • To program the two remaining HomeLink威 buttons, repeat each step for each remaining button. DO NOT erase the channels. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 3. Without releasing the button proceed with The HomeLink威 Universal Transceiver is disabled when “Canadian/Gate Operator Programming” Step 2 and the Vehicle Security Alarm is active. follow all remaining steps. Troubleshooting Tips Using HomeLink姞 If you are having trouble programming HomeLink威, here To operate, press and release the programmed are some of the most common solutions: HomeLink威 button.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information WARNING! • Your motorized door or gate will open and close while you are programming the universal transceiver. Do not program the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 POWER SUNROOF — IF EQUIPPED WARNING! The power sunroof switch is located on the overhead console. Power Sunroof Switch • Never leave children in a vehicle with the key in the ignition switch (or with the ignition in the Accessory or Run position, for vehicles equipped with Keyless Enter-N-Go™). Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE position. The sunroof will close fully and stop automatically. This is called “Express Close”. During Express Press the switch rearward and release it within one-half Close operation, any movement of the switch will stop second and the sunroof will open automatically from any the sunroof. position. The sunroof will open fully and stop automatically. This is called “Express Open”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 NOTE: If three consecutive sunroof close attempts result in Pinch Protect reversals, the fourth close attempt will be a Manual Close movement with Pinch Protect disabled. Venting Sunroof — Express Press and release the Vent button within one half second and the sunroof will open to the vent position. This is called “Express Vent”, and it will occur regardless of sunroof position. During Express Vent operation, any movement of the switch will stop the sunroof.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ignition Off Operation For Vehicles Not Equipped With The Electronic Vehicle Information Center (EVIC) The power sunroof switch will remain active for 45 seconds after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature. For Vehicles Equipped With The EVIC The power sunroof switch will remain active for up to approximately ten minutes after the ignition switch is turned to the LOCK position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 NOTE: To ensure proper operation a MOPAR威 knob and element must be used. CAUTION! • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 POWER INVERTER — IF EQUIPPED A 115 Volt (150 Watt) AC power inverter is located on the front of the center console for added convenience. This outlet can power mobile phones, electronics and other low power devices requiring power up to 150 Watts. Certain high-end video games, such as Playstation3 and XBox360 will exceed this power limit, as will most power tools. The power inverter is designed with built-in overload protection.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! To avoid serious injury or death: • Do not use a three-prong adaptor. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled, it may cause an electric shock and failure. • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 There are two cupholders located in the back for the rear Your vehicle is equipped with four cupholders. There are passengers. two illuminated cupholders located in the front.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE Glove Compartment And Storage Bin Located on the passenger side of the instrument panel are an upper storage bin and a lower glove compartment. To open the lower glove compartment, pull outward on the release handle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 Door Storage The interior door panels are equipped with lower storage areas.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the lower storage compartment, lift upward on The floor console contains both an upper and lower the lower handle to unlatch the lower storage compartment and lift the lid open. storage compartment. CONSOLE FEATURES To open the upper storage compartment, push inward on the upper handle to unlatch the upper lid and lift the lid open.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 WARNING! Do not operate this vehicle with a console compartment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distraction, resulting in death or injury. light bulbs and is powered by rechargeable lithium batteries that recharge when snapped back into place for convenience. Press in on the flashlight to release it.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To operate the flashlight, press the switch once for high, To install the Cargo Cover, insert either end of the cover into one of the two notches located in the rear trim twice for low, and a third time to return to off. panels. With one of the cover ends installed, push inward on the opposite end and install it into the same notch location of the rear trim panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 Using the handle, pull the cover toward you and guide the rear cover posts into the guides located on both sides of the rear trim panel. WARNING! In a collision a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do not store in the vehicle.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Removable Load Floor Cargo Tie-Down Loops The cargo area load floor is removable and can be There are four tie-downs (D-rings) installed in the cargo washed with mild soap and water. area for securing cargo.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 WARNING! WARNING! (Continued) • Cargo tie-down loops are not safe anchors for a child seat tether strap. In a sudden stop or collision a loop could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. • The weight and position of cargo and passengers can change the vehicle center of gravity and vehicle handling.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fold Down Speakers — If Equipped REAR WINDOW FEATURES When the liftgate is open, the speakers can swing down Rear Window Wiper/Washer off the trim panel to face rearward, for tailgating and The rear wiper/washer is controlled by a rotary switch other activities. located on the center portion of the control lever. The control lever is located on the right side of the steering column.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 Rotate the center portion of the lever upward to Rear Window Defroster the first detent position for rear wiper operation. NOTE: The rear wiper operates in an intermittent mode only. Rotate the center portion of the lever past the first detent to activate the rear washer. The washer pump and the wiper will continue to operate as long as the switch is held (for a maximum of 10 seconds).
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 The optional crossbars must also be secured in one of the • If the rear crossbar (or any metallic object) is placed seven detent positions marked with an arrow on the over the satellite radio antenna (if equipped), you may siderails to prevent movement. To move the crossbars, experience interruption of satellite radio reception.
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! (Continued) • To prevent damage to the roof of your vehicle, DO NOT carry any loads on the roof rack without crossbars installed. The load should be secured and placed on top of the crossbars, not directly on the roof. If it is necessary to place the load on the roof, place a blanket or some other protection between the load and the roof surface.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 INSTRUMENT PANEL FEATURES. . . . . . . . . . .210 ▫ Compass/Temperature/Audio . . . . . . . . . . . .232 䡵 INSTRUMENT CLUSTER . . . . . . . . . . . . . . . . .211 ▫ Average Fuel Economy. . . . . . . . . . . . . . . . . .232 䡵 INSTRUMENT CLUSTER DESCRIPTIONS . . . . .212 ▫ Distance To Empty (DTE) . . . . . . . . . . . . . . . .233 䡵 MINI-TRIP COMPUTER — IF EQUIPPED . . . . .226 ▫ Tire Pressure Monitor (TPM). . . . . . . . . . . . . .
208 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operation Instructions - (DISC MODE for CD 䡵 MEDIA CENTER 130 (SALES CODE RES) . . . . .260 and MP3/WMA Audio Play, DVD-VIDEO) . . .248 ▫ Operating Instructions — Radio Mode. . . . . . .270 ▫ LIST Button ▫ Operation Instructions — CD MODE For CD (DISC Mode for MP3/WMA Play). . . . . . . . . .253 And MP3 Audio Play. . . . . . . . . . . . . . . . . . .264 ▫ INFO Button ▫ Notes on Playing MP3 Files . . . . . . . . . . . . . .266 (DISC Mode for MP3/WMA Play). . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 209 ▫ Uconnect™ Multimedia (Satellite Radio) — If 䡵 STEERING WHEEL AUDIO CONTROLS . . . . Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .282 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . 䡵 iPod威/USB/MP3 CONTROL — IF EQUIPPED . .287 ▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . ▫ Connecting The iPod威 Or External USB 䡵 CD/DVD DISC MAINTENANCE . . . . . . . . . Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
210 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 2 3 4 — Air Outlet — Demisters — Instrument Cluster — Radio 5 6 7 8 — — — — Storage Bin Glove Compartment Climate Controls Power Outlet I nf or mat i onPr ov i dedby : 9 — Heated Seat Switch – If Equipped 10 — Hazard Warning Flasher 11 — ESC OFF Switch – If Equipped 12 — Heated Seat Switch – If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 211 INSTRUMENT CLUSTER 4 I nf or mat i onPr ov i dedby :
212 UNDERSTANDING YOUR INSTRUMENT PANEL If jump starting is required, refer to “Jump Starting Procedures” in “What To Do In Emergencies”. INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge / Fuel Door Reminder When the ignition switch is in the ON/RUN position, the pointer will show the level of fuel remaining in the fuel tank. The fuel pump symbol points to the side of the vehicle where the fuel door is located. 2. Charging System Light This light shows the status of the electrical charging system.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 on briefly as a bulb check. If the light does not come on 6. Speedometer during starting, have the system checked by an authoThe Speedometer shows the vehicle speed in miles per rized dealer. hour (MPH) and kilometers per hour (km/h). 4. Oil Pressure Warning Light 7. Air Bag Warning Light This light indicates low engine oil pressure.
214 UNDERSTANDING YOUR INSTRUMENT PANEL alert you to turn the signals off. If either indicator flashes If the ABS light is on, the brake system should be serviced at a rapid rate, check for a defective outside light bulb. as soon as possible to restore the benefits of Anti-Lock brakes. If the ABS light does not turn on when the 9. High Beam Indicator ignition switch is turned to the ON/RUN position, have This indicator shows that the high beam head- the light inspected by an authorized dealer.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 normal, turn the engine off immediately and call for service. Refer to “If Your Engine Overheats” in “What To The white area of the scale shows the permissible engine Do In Emergencies” for further information. revolutions-per-minute (RPM x 1000) for each gear range. Before reaching the red area, ease up on the accelerator to 14. Brake Warning Light prevent engine damage. This light monitors various brake functions, 12.
216 UNDERSTANDING YOUR INSTRUMENT PANEL booster, the ABS pump will run when applying the brake and a brake pedal pulsation may be felt during each stop. WARNING! The dual brake system provides a reserve braking capac- Driving a vehicle with the red brake light on is ity in the event of a failure to a portion of the hydraulic dangerous. Part of the brake system may have failed. system. A leak in either half of the dual brake system is It will take longer to stop the vehicle. You could have a collision.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 15.
218 UNDERSTANDING YOUR INSTRUMENT PANEL The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to exceed the upper limits of the normal operating range. CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a The Shift Lever Indicator is self-contained within the different size than the size indicated on the vehicle instrument cluster. It displays the gear position of the placard or tire inflation pressure label, you should deterautomatic transmission. mine the proper tire inflation pressure for those tires.
220 UNDERSTANDING YOUR INSTRUMENT PANEL Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 23. Odometer Display / Trip Odometer Display Area Vehicle Odometer Messages This display indicates the total distance the vehicle has When the appropriate conditions exist, the following odometer messages will display: been driven. NOTE: U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven.
222 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the vehicle is equipped with the optional Electronic Vehicle Information Center (EVIC) in the instrument cluster, all warnings including “Door Ajar”, and “Gate Ajar” will only be displayed in the EVIC display. For additional information, refer to “Electronic Vehicle Information Center — If Equipped”. LoW tirE When tire pressure is low, the odometer display will toggle between LoW and tirE for three cycles.
UNDERSTANDING YOUR INSTRUMENT PANEL 223 engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and release the Trip Odometer button on the instrument cluster. To reset the oil change indicator system (after performing the scheduled maintenance), refer to the following procedure: 24.
224 UNDERSTANDING YOUR INSTRUMENT PANEL 26. Front Fog Light Indicator — If Equipped CAUTION! Prolonged driving with the MIL on could cause damage to the engine control system. It also could affect fuel economy and drivability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required. WARNING! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 system. If this light remains on after several ignition 29. 4WD! Warning Light — If Equipped cycles, and the vehicle has been driven several miles This light monitors the 4-Wheel Drive (4WD) (kilometers) at speeds greater than 30 mph (48 km/h), see system. The light will come on, for a bulb your authorized dealer as soon as possible to have the check, when the ignition key is turned to the problem diagnosed and corrected.
226 UNDERSTANDING YOUR INSTRUMENT PANEL MINI-TRIP COMPUTER — IF EQUIPPED Control Buttons The Mini-Trip Computer is located in the instrument cluster and features a driver-interactive trip information and temperature display. NOTE: The system will display the last known outside temperature when starting the vehicle and may need to be driven several minutes before the updated temperature is displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 Trip A RESET Button To reset the display shown, turn the ignition switch to the Shows the total distance traveled for Trip A since the last ON position, then press and hold the RESET button reset. located on the steering wheel. Trip B The following displays can be reset or changed: Shows the total distance traveled for Trip B since the last • Trip A reset. • Trip B Trip Odometer (ODO) This display shows the distance traveled since the last reset.
228 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED The EVIC consists of the following: • System Status The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the • Vehicle Information Warning Message Displays instrument cluster.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 The system allows the driver to select information by MENU Button pressing the following buttons mounted on the steering Press and release the MENU button to scroll wheel: through the main menus (Fuel Economy, Warnings, Timer, Units, System, Personal Settings) or to exit sub-menus. COMPASS Button Press and release the COMPASS button to display one of eight compass readings and the outside temperature or to exit sub-menus.
230 UNDERSTANDING YOUR INSTRUMENT PANEL • Personal Settings Not Avail. — Vehicle not in PARK (automatic transmission) or vehicle is in motion Press and release the DOWN button to scroll (manual transmission). downward through the sub-menus. • Door Ajar (with vehicle graphic showing which door is open. A single chime sounds if the vehicle is in When the appropriate conditions exist, the EVIC displays motion).
UNDERSTANDING YOUR INSTRUMENT PANEL 231 • Remote Start Aborted — Fuel Low indicator system is duty-cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style.
232 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the indicator message illuminates when you occur if a resettable function is currently being displayed. start the vehicle, the oil change indicator system did not To reset all resettable functions, press and release the SELECT button a second time within three seconds of reset. If necessary repeat this procedure. resetting the currently displayed function. Reset ALL will EVIC Functions be displayed during this three-second window.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 history information will be erased, and the averaging will ⬙LOW FUEL⬙ text and a new DTE value will be displayed, based on the current values in the DTE calculacontinue from the last fuel reading before the reset. tion and the current fuel tank level. Distance To Empty (DTE) Shows the estimated distance that can be traveled with Tire Pressure Monitor (TPM) the fuel remaining in the tank.
234 UNDERSTANDING YOUR INSTRUMENT PANEL reset all digits will change to zeros and time will start English, Espanol, Deutsch, Italiano, Francais or NL deincrementing again if the ignition switch is in RUN or pending on availability. As you continue, the displayed information will be shown in the selected language. START. NOTE: Uconnect™ language will not change using the EVIC. Please refer to “Language Selection” in Uconnect™ phone — If Equipped for details.
UNDERSTANDING YOUR INSTRUMENT PANEL 235 position (automatic transmission). Press and hold the and hold the SELECT button when in this display until SELECT button when in this display until “ON” or “ON” or “OFF” appears to make your selection. “OFF” appears to make your selection.
236 UNDERSTANDING YOUR INSTRUMENT PANEL Key Off Power Delay Hill Start Assist (HSA) — If Equipped When this feature is selected the power window switches, radio, Uconnect™ phone, power sunroof, and power outlets will remain active for up to 10 minutes after the ignition switch has been turned OFF. Opening either front vehicle door will cancel this feature. Press and hold the SELECT button when in this display until “OFF”, “45 sec.”, “5 min.”, or “10 min.” appears to make your selection.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 Automatic Compass Calibration Manual Compass Calibration This compass is self-calibrating, which eliminates the need to set the compass manually. When the vehicle is new, the compass may appear erratic and the EVIC will display “CAL” until the compass is calibrated. You may also calibrate the compass by completing one or more 360–degree turns (in an area free from large metal or metallic objects) until the “CAL” message displayed in the EVIC turns off.
238 UNDERSTANDING YOUR INSTRUMENT PANEL 5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the “CAL” indicator turns off. The compass will now function normally. Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To compensate for the differences, the variance should be set for the zone where the vehicle is driven, per the zone map.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 3. Press the DOWN button until “Compass Variance” message and the last variance zone number displays in the EVIC. 4. Press and release the SELECT button until the proper variance zone is selected according to the map. 5. Press and release the COMPASS button to exit. 4 MEDIA CENTER 230 (REQ) — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate.
240 UNDERSTANDING YOUR INSTRUMENT PANEL another selection. Holding either button will bypass stations without stopping, until you release it. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second SCAN Button time to turn off the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes Press this button to operate the Uconnect™ Phone feature will begin to blink. (if equipped). Refer to “Uconnect™ Phone” for further details. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL conIf your vehicle is not equipped with or this feature is not trol knob to save the time change.
242 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL Pressing the RW (Rewind) or FF (Fast Forward) buttons control knob to the right or left to increase or decrease the causes the tuner to search for the next frequency in the treble tones. direction of the arrows. This feature operates in AM, FM or Satellite (if equipped) frequencies. Push the rotary TUNE/SCROLL control knob a fourth time and BALANCE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be selected. Many radio stations do not currently broadcast Music Type information.
244 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Soft Rhythm and Blues Sports Talk Top 40 Weather 16-Digit Character Display Soft R & B Sports Talk Top 40 Weather SETUP Button Pressing the SETUP button allows you to select between the following items: NOTE: Turn the TUNE/SCROLL control knob to scroll through the entries. Push the AUDIO/SELECT button to select an entry and make changes.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 • DVD Play Options - Selecting the DVD Play Options will display the following: • Subtitle – Repeatedly pressing SELECT will switch subtitles to different subtitle languages that are available on the disc (if equipped). • Audio Stream – Repeatedly pressing SELECT will switch to different audio languages (if supported on the disc) (if equipped). • Angle – Repeatedly pressing SELECT will change the viewing angle if supported by the DVD disc (if equipped).
246 UNDERSTANDING YOUR INSTRUMENT PANEL Menu Language — If Equipped Subtitle Language — If Equipped Selecting this item will allow the user to choose the default startup DVD menu language (effective only if language supported by disc). If you want to select a language not listed, then scroll down and select ⬙other.⬙ Enter the four-digit country code using the TUNE/ SCROLL control knob to scroll up and down to select the number and then push to select.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 Aspect Ratio — If Equipped SET Button — To Set the Pushbutton Memory Selecting this item allows you to choose between wide When you are receiving a station that you wish to commit to pushbutton memory, press the SET button. screen, pan scan, and letter box. The symbol SET 1 will now show in the display window.
248 UNDERSTANDING YOUR INSTRUMENT PANEL Every time a preset button is used, a corresponding vehicle to an authorized dealer to change the region code of the player a maximum of five times. button number will display. Buttons 1 - 6 These buttons tune the radio to the stations that you commit to pushbutton memory {12 AM, 12 FM, and 12 Satellite (if equipped) stations}. DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 prompt when to INSERT DISC. After the radio displays display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. ⬙INSERT DISC,⬙ insert the CD into the player. Radio display will show ⬙LOADING DISC⬙ when the disc Press and hold the EJECT button for five seconds and all is loading and “READING DISC” when the radio is CDs will be ejected from the radio. reading the disc.
250 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (CD MODE) Supported Media (Disc Types) Press this button to change the display from a large CD The MP3/WMA file recording media supported by the playing time display to a small CD playing time display. radio are CDDA, CD-R, CD-RW, MP3,WMA, DVD Video, DVD-R, DVD-RW, DVD+R, DVD+RW, and CDDA+MP3.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙.⬙ and a threecharacter extension) • Level 2: 31 (including a separator ⬙.⬙ and a threecharacter extension) Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3/ WMA files).
252 UNDERSTANDING YOUR INSTRUMENT PANEL MPEG Specification MPEG-1 Audio Layer 3 Sampling Frequency (kHz) 48, 44.1, 32 MPEG-2 Audio Layer 3 24, 22.05, 16 WMA Specification WMA Sampling Frequency (kHz) 44.1 and 48 Bit Rate (kbps) 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48 160, 128, 144, 112, 96, 80, 64, 56, 48 Bit Rate (kbps) 48, 64, 96, 128, 160, 192 VBR Playlist files are not supported. MP3 Pro files are not supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. To create a single-session disc, enable the “Disc at Once” option before writing to the disc. Press the INFO button once more to return to ⬙elapsed time⬙ priority mode. LIST Button (DISC Mode for MP3/WMA Play) Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display.
254 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The AUX device must be turned on and the device’s volume set to the proper level. If the AUX audio is not loud enough, turn the device’s volume up. If the AUX audio sounds distorted, turn the device’s volume down. SEEK Button (Auxiliary Mode) No function. SCAN Button (Auxiliary Mode) No function. EJECT Button (Auxiliary Mode) No function. TIME Button (Auxiliary Mode) Press the TIME button to change the display from elapsed playing time to time of day.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 Operating Instructions - Video Entertainment System (VES)™ (If Equipped) DTS™ “DTS™ and “DTS™ 2.0” are trademarks of Digital TheRefer to “Video Entertainment System (VES)™” for fur- ater Systems, Inc. ther details. Uconnect™ Multimedia (Satellite Radio) — If Equipped Dolby威 Manufactured under license from Dolby威 Laboratories.
256 UNDERSTANDING YOUR INSTRUMENT PANEL System Activation To access the ESN/SID, refer to the following steps: Sirius Satellite Radio service is pre-activated, and you may begin listening immediately to the one year of audio service that is included with the factory-installed satellite radio system in your vehicle. Sirius will supply a welcome kit that contains general information, including how to setup your on-line listening account.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 decreased performance. Larger luggage items such as Operating Instructions - Uconnect™ Multimedia bikes should be placed as far rearward as possible, within (Satellite) Mode the loading design of the rack. Do not place items directly NOTE: The ignition switch must be in the ON/RUN or on or above the antenna. ACC position to operate the radio.
258 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button MUSIC TYPE Button Pressing the INFO button will cycle the display information between Artist, Song Title, and Composer (if available). Also, pressing and holding the INFO button for an additional three seconds will make the radio display the Song Title all of the time (press and hold again to return to normal display). Pressing this button once will turn on the Music Type mode for five seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 • Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number. This number is used to activate, deactivate, or change the Sirius subscription. You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET/RND button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM.
260 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 730N/430/430N (RHR/RER/RBZ/ RHB) CD/DVD/HDD/NAV — IF EQUIPPED MEDIA CENTER 130 (SALES CODE RES) NOTE: The radio sales code is located on the lower right NOTE: The sales code is located on the lower right side side of the radio faceplate. of the unit’s faceplate. Refer to your Uconnect™ Multimedia RHR, RER, RBZ or RHB user’s manual for detailed operating instructions.
UNDERSTANDING YOUR INSTRUMENT PANEL 261 Operating Instructions — Radio Mode SEEK Buttons NOTE: The ignition switch must be in the ON or ACC Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch position to operate the radio. to seek up and the left switch to seek down. The radio Power Switch/Volume Control (Rotary) will remain tuned to the new station until you make Push the ON/VOLUME control knob to turn on the another selection.
262 UNDERSTANDING YOUR INSTRUMENT PANEL 3. After adjusting the hours, press the right side TUNE/ Setting the Tone, Balance, and Fade SCROLL control knob to set the minutes. The minutes Push the rotary TUNE/SCROLL control knob and BASS will begin to blink. will display. Turn the TUNE/SCROLL control knob to 4. Adjust the minutes using the right side TUNE/ the right or left to increase or decrease the bass tones. SCROLL control knob.
UNDERSTANDING YOUR INSTRUMENT PANEL 263 Push the rotary TUNE/SCROLL control knob a fifth time SET/RND button, the station will continue to play but and FADE will display. Turn the TUNE/SCROLL control will not be stored into pushbutton memory. knob to the left or right to adjust the sound level between You may add a second station to each pushbutton by the front and rear speakers.
264 UNDERSTANDING YOUR INSTRUMENT PANEL radio display. If a CD does not go into the slot more than 1.0 in (2.5 cm), a disc may already be loaded and must be Pressing the DISC button will allow you to switch from ejected before a new disc can be loaded. AM/FM modes to Disc modes. If you insert a disc with the ignition ON and the radio Operation Instructions — CD MODE For CD And ON, the unit will switch from radio to CD mode and MP3 Audio Play begin to play when you insert the disc.
UNDERSTANDING YOUR INSTRUMENT PANEL 265 EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD and MP3 modes. TIME Button Press this button to change the display from a large CD If you have ejected a disc and have not removed it within playing time display to a small CD playing time display. 10 seconds, it will be reloaded.
266 UNDERSTANDING YOUR INSTRUMENT PANEL SET/RND Button (Random Play Button) Supported Media (Disc Types) Press this button while the CD is playing to activate The MP3 file recording media supported by the radio are Random Play. This feature plays the selections on the CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. compact disc in random order to provide an interesting Supported Medium Formats (File Systems) change of pace.
UNDERSTANDING YOUR INSTRUMENT PANEL 267 display the file name and folder name, and will assign a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.) • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙.⬙ and a threecharacter extension) • Level 2: 31 (including a separator ⬙.
268 UNDERSTANDING YOUR INSTRUMENT PANEL MPEG Specification MPEG-1 Audio Layer 3 Sampling Frequency (kHz) 48, 44.1, 32 MPEG-2 Audio Layer 3 24, 22.05, 16 Bit Rate (kbps) 320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium.
UNDERSTANDING YOUR INSTRUMENT PANEL 269 To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. To create a single-session disc, enable the “Disc at Once” option before writing to the disc. NOTE: The AUX device must be turned on and the device’s volume set to proper level. If the AUX audio is not loud enough, turn the device’s volume up. If the AUX audio sounds distorted, turn the device’s volume down.
270 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 130 WITH SATELLITE RADIO (SALES CODE RES+RSC) Operating Instructions — Radio Mode NOTE: The radio sales code is located on the lower right side of the radio faceplate. NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With Press and release the SEEK buttons to search for the next Uconnect Phone” message will display on the radio listenable station in AM/FM mode. Press the right switch screen. to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make Phone Button Uconnect™ Phone — If Equipped another selection.
272 UNDERSTANDING YOUR INSTRUMENT PANEL starting at Step 2. For vehicles not equipped with satellite radio, press the SETUP button and then follow the above 1. Press and hold the TIME button until the hours blink. procedure, starting at Step 2. 2. Adjust the hours by turning the right side TUNE/ INFO Button SCROLL control knob. Press the INFO button for an RDS station (one with call 3. After adjusting the hours, press the right side TUNE/ letters displayed).
UNDERSTANDING YOUR INSTRUMENT PANEL 273 Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control Push the rotary TUNE/SCROLL control knob and BASS knob to the left or right to adjust the sound level between will display. Turn the TUNE/SCROLL control knob to the front and rear speakers. the right or left to increase or decrease the bass tones.
274 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the MUSIC TYPE button to select the following format types: Program Type No program type or undefined Adult Hits Classical Classic Rock College Country Foreign Language Information Jazz News Nostalgia Oldies 16-Digit Character Display None Adlt Hit Classicl Cls Rock College Country Language Inform Jazz News Nostalga Oldies Program Type Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top
UNDERSTANDING YOUR INSTRUMENT PANEL 275 the minutes using the right side TUNE/SCROLL conBy pressing the SEEK button when the Music Type icon trol knob. Press the TUNE/SCROLL control knob to is displayed, the radio will be tuned to the next frequency save time change. station with the same selected Music Type name. The Music Type function only operates when in the FM AM/FM Button mode. Press the button to select either AM or FM mode.
276 UNDERSTANDING YOUR INSTRUMENT PANEL the SET/RND button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice. Operation Instructions — CD MODE for CD and MP3 Audio Play NOTE: • The ignition switch must be in the ON or ACC position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 277 If you insert a disc with the ignition ON and the radio EJECT Button - Ejecting a CD ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will Press the EJECT button to eject the CD. show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. CAUTION! • This CD player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism.
278 UNDERSTANDING YOUR INSTRUMENT PANEL the current selection. Pressing and holding the SEEK SET/RND Button (Random Play Button) button will allow faster scrolling through the tracks in Press this button while the CD is playing to activate CD and MP3 modes. Random Play. This feature plays the selections on the compact disc in random order to provide an interesting TIME Button change of pace. Press this button to change the display from a large CD playing time display to a small CD playing time display.
UNDERSTANDING YOUR INSTRUMENT PANEL 279 Supported Media (Disc Types) The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. Supported Medium Formats (File Systems) display the file name and folder name, and will assign a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.
280 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. MPEG Specification MPEG-1 Audio Layer 3 Sampling Frequency (kHz) 48, 44.
UNDERSTANDING YOUR INSTRUMENT PANEL 281 Playback of MP3 Files LIST Button (CD Mode for MP3 Play) When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files. Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob.
282 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack which allows the user to plug in a portable device such as an MP3 player or cassette player and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. TIME Button (Auxiliary Mode) Press this button to change the display to time of day.
UNDERSTANDING YOUR INSTRUMENT PANEL 283 System Activation To access the ESN/SID, refer to the following steps: Sirius Satellite Radio service is pre-activated, and you may begin listening immediately to the one year of audio service that is included with the factory-installed satellite radio system in your vehicle. Sirius will supply a welcome kit that contains general information, including how to setup your on-line listening account.
284 UNDERSTANDING YOUR INSTRUMENT PANEL decreased performance. Larger luggage items such as Operating Instructions - Uconnect™ Multimedia bikes should be placed as far rearward as possible, within (Satellite) Mode the loading design of the rack. Do not place items directly NOTE: The ignition switch must be in the ON/RUN or on or above the antenna. ACC position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 285 INFO Button MUSIC TYPE Button Pressing the INFO button will cycle the display information between Artist, Song Title, and Composer (if available). Also, pressing and holding the INFO button for an additional three seconds will make the radio display the Song Title all of the time (press and hold again to return to normal display). Pressing this button once will turn on the Music Type mode for five seconds.
286 UNDERSTANDING YOUR INSTRUMENT PANEL SETUP Button Pressing the SETUP button allows you to select the following items: • Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number. This number is used to activate, deactivate, or change the Sirius subscription. You may add a second channel to each pushbutton by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 287 NOTE: iPod姞/USB/MP3 CONTROL — IF EQUIPPED NOTE: This section is for sales code RES and REQ/ • If the radio has a USB port, refer to the appropriate REL/RET radios only with Uconnect™. For sales code Uconnect™ Multimedia radio User’s Manual for RBZ/RHB, RHR, RHP, RHW or RB2 touch-screen radio iPod威 or external USB device support capability.
288 UNDERSTANDING YOUR INSTRUMENT PANEL Once the audio device is connected and synchronized to Use the connection cable to connect an iPod威 or external the vehicle’s iPod威/USB/MP3 control system (iPod威 or USB device to the vehicle’s USB/AUX connector port external USB device may take a few minutes to connect), the audio device starts charging and is ready for use by which is located in the center console or glove compartpressing radio switches, as described below. ment.
UNDERSTANDING YOUR INSTRUMENT PANEL 289 • The audio device can be controlled using the radio mode. In Play mode, the following buttons on the radio buttons to Play, Browse, and List the iPod威 contents. faceplate may be used to control the iPod威 or external USB device and display data: • The audio device battery charges when plugged into the USB/AUX connector (if supported by the specific • Use the TUNE control knob to select the next or previous track.
290 UNDERSTANDING YOUR INSTRUMENT PANEL • A single press backward << RW or forward FF>> will • Press the SCAN button to use iPod威/USB/MP3 dejump backward or forward respectively, for five secvice scan mode, which will play the first 10 seconds of each track in the current list and then forward to the onds. next song. To stop SCAN mode and start playing the • Use the << SEEK and SEEK>> buttons to jump to the desired track, when it is playing the track, press the previous or next track.
UNDERSTANDING YOUR INSTRUMENT PANEL 291 List Or Browse Mode During Play mode, pressing any of the buttons described below, will bring up List mode. List mode enables scrolling through the list of menus and tracks on the audio device. • TUNE control knob: The TUNE control knob functions in a similar manner as the scroll wheel on the audio device or external USB device.
292 UNDERSTANDING YOUR INSTRUMENT PANEL • To exit List mode without selecting a track, press the same PRESET button again to go back to Play mode. • LIST button: The LIST button will display the top level menu of the iPod威 or external USB device. Turn the TUNE control knob to list the top-menu item to be selected and press the TUNE control knob. This will display the next sub-menu list item on the audio device, then follow the same steps to go to the desired track in that list.
UNDERSTANDING YOUR INSTRUMENT PANEL 293 Bluetooth Streaming Audio (BTSA) Selecting Different Audio Device Music can be streamed from your cellular phone to the 1. Press PHONE button to begin. Uconnect™ phone system. 2. After the ⬙Ready⬙ prompt and the following beep, say Controlling BTSA Using Radio Buttons ⬙Setup⬙, then ⬙Select Audio Devices⬙. To get into the BTSA mode, press either “AUX” button on 3.
294 UNDERSTANDING YOUR INSTRUMENT PANEL Browse Browsing is not available on a BTSA device. Only the current song that is playing will display info. STEERING WHEEL AUDIO CONTROLS The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. Remote Sound System Controls (Back View Of Steering Wheel) The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system.
UNDERSTANDING YOUR INSTRUMENT PANEL 295 Pressing the center button will make the radio switch CD Player between the various modes available (AM/FM/SAT/ Pressing the top of the switch once will go to the next CD/HDD/AUX/VES, etc.). track on the CD. Pressing the bottom of the switch once The left-hand control is a rocker-type switch with a will go to the beginning of the current track, or to the pushbutton in the center.
296 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particuTo keep a CD/DVD in good condition, take the following lar disc, it may be damaged (i.e., scratched, reflective coating removed, a hair, moisture or dew on the disc) precautions: oversized, or have protection encoding. Try a known 1. Handle the disc by its edge; avoid touching the good disc before considering disc player service. surface. RADIO OPERATION AND MOBILE PHONES 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 297 The Manual Temperature Controls consist of a series of The air conditioning and heating system is designed to outer rotary dials and inner push knobs. make you comfortable in all types of weather. Blower Control CLIMATE CONTROLS Manual Heating And Air Conditioning Rotate this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control to the right from the “O” (OFF) position.
298 UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control Mode Control (Air Direction) Rotate this control to regulate the temperature of the air inside the passenger compartment. Rotating the dial left into the blue area of the scale indicates cooler temperatures, while rotating right into the red area indicates warmer temperatures.
UNDERSTANDING YOUR INSTRUMENT PANEL 299 Defrost Bi-Level Air is directed through the panel and floor outlets. Air is directed through the windshield and side window demist outlets. Use this mode with maxiNOTE: For all settings, except full cold or full hot, mum blower and temperature settings for best windthere is a difference in temperature between the upper shield and side window defrosting. and lower outlets. The warmer air flows to the floor outlets.
300 UNDERSTANDING YOUR INSTRUMENT PANEL • The A/C will engage automatically to prevent fogging when the recirculation button is pressed and the mode Pressing the Recirculation Control button will control is set to panel or panel / floor. put the system in recirculation mode. This can be used when outside conditions such as • The A/C can be deselected manually without disturbing the mode control selection. smoke, odors, dust, or high humidity are present.
UNDERSTANDING YOUR INSTRUMENT PANEL 301 NOTE: The air conditioning compressor will not engage until the engine has been running for about 10 seconds. • MAX A/C For maximum cooling use the A/C and recirculation buttons at the same time. • ECONOMY MODE 4 If economy mode is desired, press the A/C button to turn OFF the indicator light and the A/C compressor. Then, move the temperature control to the desired temperature.
302 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The AUTO position performs best for front seat The recommended setting for maximum comfort for the occupants only. average person is 72°F (22°C); however, this may vary. NOTE: Dial in the temperature you would • The temperature setting can be adjusted at anytime like the system to maintain by rotating without affecting automatic operation. the Temperature Control knob.
UNDERSTANDING YOUR INSTRUMENT PANEL 303 Blower Control Mode Preferred Automatic, or Blower and Mode Preferred Automatic. This means the operator can override the blower, the mode, or both. There is a manual blower For full automatic operation or for range for times when the AUTO setting is not desired. automatic blower operation, turn the The blower can be set to any fixed blower speed by knob to the AUTO position. In manual rotating the Blower Control knob (on the left).
304 UNDERSTANDING YOUR INSTRUMENT PANEL I nf or mat i onPr ov i dedby :
UNDERSTANDING YOUR INSTRUMENT PANEL 305 The operator can override the AUTO mode setting to • Floor change airflow distribution by rotating the Mode Control Air is directed through the floor outlets with a knob (on the right) to one of the following positions. small amount flowing through the defrost and • Panel side window demist outlets. Air is directed through the outlets in the instru- • Mix ment panel. These outlets can be adjusted to direct Air is directed through the floor, defrost, and side airflow.
306 UNDERSTANDING YOUR INSTRUMENT PANEL • Air Conditioner Control NOTE: Press this button to turn on the air • When the ignition switch is turned to the LOCK position, the recirculation feature will be cancelled. conditioning during manual operation only. When the air conditioning is • In cold weather, use of the Recirculation mode may turned on, cool dehumidified air will lead to excessive window fogging.
UNDERSTANDING YOUR INSTRUMENT PANEL 307 • Most of the time, when in Automatic Operation, you can temporarily put the system into Recirculation Mode by pressing the Recirculation button. However, under certain conditions, while in Automatic Mode, the system is blowing air out the defrost vents. When these conditions are present, and the Recirculation button is pressed, the indicator will flash and then turn off. This tells you that you are unable to go into Recirculation Mode at this time.
308 UNDERSTANDING YOUR INSTRUMENT PANEL adequate system lubrication to minimize the possibility FLOOR, MIX, or DEFROST mode. The air is directed at of compressor damage when the system is started again. the area of the windows through which you view the outside mirrors. Window Fogging Interior fogging on the windshield can be quickly re- Outside Air Intake moved by turning the mode selector to Defrost. The Defrost/Floor mode can be used to maintain a clear windshield and provide sufficient heating.
UNDERSTANDING YOUR INSTRUMENT PANEL 309 Control Setting Suggestions for Various Weather Conditions 4 I nf or mat i onPr ov i dedby :
I nf or mat i onPr ov i dedby :
STARTING AND OPERATING CONTENTS 䡵 STARTING PROCEDURES . . . . . . . . . . . . . . . .315 䡵 MANUAL TRANSMISSION — IF EQUIPPED . .318 ▫ Manual Transmission – If Equipped . . . . . . . .315 ▫ Five–Speed Manual Transmission . . . . . . . . . .318 ▫ Automatic Transmission – If Equipped . . . . . .316 ▫ Recommended Shift Speeds . . . . . . . . . . . . . .320 ▫ Normal Starting. . . . . . . . . . . . . . . . . . . . . . .316 ▫ Downshifting . . . . . . . . . . . . . . . . . . . . . . . .
312 STARTING AND OPERATING 䡵 AUTOSTICK威 . . . . . . . . . . . . . . . . . . . . . . . . .329 ▫ Brake Assist System (BAS) . . . . . . . . . . . . . . .340 ▫ Continuously Variable Automatic Transmission (CVT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .329 ▫ Electronic Roll Mitigation (ERM) . . . . . . . . . .341 䡵 FOUR-WHEEL DRIVE OPERATION — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . .331 䡵 ON-ROAD DRIVING TIPS . . . . . . . . . . . . . . . .331 䡵 POWER STEERING . .
STARTING AND OPERATING 313 䡵 TIRES — GENERAL INFORMATION. . . . . . . . .359 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . .366 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . .359 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . .367 ▫ Tire Inflation Pressures . . . . . . . . . . . . . . . . .360 ▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . .367 ▫ Tire Pressures For High Speed Operation . . . .362 ▫ Replacement Tires . . . . . . . . . . . . .
314 STARTING AND OPERATING ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . .382 䡵 TRAILER TOWING . . . . . . . . . . . . . . . . . . . . .390 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . . .382 ▫ Common Towing Definitions . . . . . . . . . . . . .390 ▫ E-85 Usage In Non-Flex Fuel Vehicles . . . . . . .383 ▫ Trailer Hitch Classification . . . . . . . . . . . . . . .393 ▫ MMT In Gasoline . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 315 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! • Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, and remove the key fob from the ignition. When leaving the vehicle, always lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle.
316 STARTING AND OPERATING automatically in 10 seconds. If this occurs, turn the ignition switch to the LOCK position, wait 10 to 15 The shift lever must be in the PARK or NEUTRAL seconds, then repeat the “Normal Starting” procedure. position before you can start the engine. Apply the brakes before shifting to any driving gear.
STARTING AND OPERATING 317 If Engine Fails To Start WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from another vehicle.
318 STARTING AND OPERATING CAUTION! WARNING! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. Remember to disconnect the engine block heater cord before driving. Damage to the 110-115 Volt electrical cord could cause electrocution. After Starting MANUAL TRANSMISSION — IF EQUIPPED The idle speed is controlled automatically and it will Five–Speed Manual Transmission decrease as the engine warms up.
STARTING AND OPERATING 319 Fully press the clutch pedal before you shift gears. As you Use each gear in numerical order, do not skip a gear. Be release the clutch pedal, lightly press the accelerator sure the transmission is in first gear, (not third), when pedal. starting from a standing position. Damage to the clutch can result from starting in third gear. For most city driving, you will find it easier to use only the lower gears.
320 STARTING AND OPERATING Recommended Shift Speeds Downshifting To use your manual transmission for optimal fuel Proper downshifting will improve fuel economy and economy, it should be upshifted as listed in the following prolong engine life. table.
STARTING AND OPERATING 321 AUTOMATIC TRANSMISSION — IF EQUIPPED WARNING! CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift between PARK, REVERSE, NEUTRAL, or DRIVE when the engine is above idle speed.
322 STARTING AND OPERATING WARNING! (Continued) • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever. • Do not leave the ignition key in or near the vehicle. A child could operate power windows, other controls, or move the vehicle.
STARTING AND OPERATING 323 Continuously Variable Automatic Transmission (CVT) Be sure to keep your foot on the brake pedal when moving the shift lever between these gears. The shift lever position display (located in the instrument cluster) indicates the transmission gear range. You must press the brake pedal to move the shift lever out of PARK (refer to “Brake/Transmission Shift Interlock System” in this section). To drive, move the shift lever from PARK or NEUTRAL to the DRIVE position.
324 STARTING AND OPERATING NOTE: After selecting any gear range, wait a moment to PARK allow the selected gear to engage before accelerating. This range supplements the parking brake by locking the This is especially important when the engine is cold. transmission. The engine can be started in this range. Never attempt to use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range.
STARTING AND OPERATING 325 WARNING! WARNING! (Continued) • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Your vehicle could move and injure you and others if it is not completely in PARK. Check by trying to move the shift lever rearward (with the brake pedal released) after you have placed it in PARK. Make sure the transmission is in PARK before leaving the vehicle.
326 STARTING AND OPERATING WARNING! (Continued) CAUTION! • When leaving the vehicle, always remove the ignition key and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever.
STARTING AND OPERATING 327 • With brake pedal released, verify that the shift lever will not move out of PARK. REVERSE This range is for moving the vehicle backward. Shift into REVERSE only after the vehicle has come to a complete stop. WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision.
328 STARTING AND OPERATING DRIVE This range should be used for most city and highway driving. It provides the best fuel economy. The DRIVE position provides optimum driving characteristics under all normal operating conditions. When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading conditions, in hilly terrain, traveling into strong head winds, or while towing heavy trailers), use the AutoStick威 shift control (if equipped) to select a lower gear ratio.
STARTING AND OPERATING 329 AUTOSTICK姞 Continuously Variable Automatic Transmission (CVT) When the shift lever is in the DRIVE position, AutoStick威 is activated by moving the shift lever side-to-side. Moving the shift lever to the right (+) will activate AutoStick威 and shift up to the next higher manual ratio, unless you are already operating in or near Overdrive, in which case sixth gear ratio will be selected.
330 STARTING AND OPERATING • The transmission will automatically upshift when nec- • To disengage AutoStick威 mode, hold the shift lever to essary to prevent engine over-speed. the right (+) until “D” is once again displayed in the instrument cluster. You can shift in or out of the • If a downshift would cause the engine to overspeed, AutoStick威 mode at any time without taking your foot that shift will not occur until it is safe for the engine. off the accelerator pedal.
STARTING AND OPERATING 331 traction surfaces, activate the “4WD LOCK” switch by pulling up once and releasing. This locks the center coupling allowing more torque to be sent to the rear This feature provides full time, on-demand, four–wheel wheels. The “4WD Indicator Light” will come on in the drive (4WD). cluster. This can be done on the fly, at any vehicle speed. To deactivate, simply pull on the switch one more time. The “4WD Indicator Light” will then go out.
332 STARTING AND OPERATING An advantage of the higher ground clearance is a better view of the road, allowing you to anticipate problems. They are not designed for cornering at the same speeds as conventional two-wheel drive vehicles any more than low-slung sports cars are designed to perform satisfactorily in off-road conditions. If at all possible, avoid sharp turns or abrupt maneuvers.
STARTING AND OPERATING 333 WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur.
334 STARTING AND OPERATING If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. PARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied. Also, be certain to leave an automatic transmission in PARK, or manual transmission in REVERSE or first gear.
STARTING AND OPERATING 335 NOTE: • When the parking brake is applied and the automatic transmission is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • This light only shows that the parking brake is applied. It does not show the degree of brake application.
336 STARTING AND OPERATING BRAKE SYSTEM WARNING! (Continued) • Always fully apply the parking brake when leaving your vehicle or it may roll and cause damage or injury. Also, be certain to leave an automatic transmission in PARK, a manual transmission in REVERSE or first gear. Failure to do so may cause the vehicle to roll and cause damage or injury. Your vehicle is equipped with power assisted brakes as standard equipment.
STARTING AND OPERATING 337 If either of the two hydraulic systems lose normal capability, the remaining system will still function with some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop. In addition, if the malfunction is caused by an internal leak, as the brake fluid in the master cylinder drops, the “Brake Warning Light” will light.
338 STARTING AND OPERATING WARNING! (Continued) • The ABS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. • The capabilities of an ABS-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others. required. However, the conventional brake system will continue to operate normally if the “Brake Warning Light” is not on.
STARTING AND OPERATING 339 working properly. This self-check occurs each time the vehicle is started and accelerated past 7 mph (11 km/h). ABS is activated during braking under certain road or stopping conditions. ABS-inducing conditions can include ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops.
340 STARTING AND OPERATING stability. A feature of the TCS system functions similar to a limited slip differential and controls the wheel spin across a driven axle. If one wheel on a driven axle is spinning faster than the other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not spinning. This feature remains active even if TCS and ESC are in Anti-Lock Brake System (ABS) either the “Partial Off” or “Full Off” modes.
STARTING AND OPERATING 341 quickly results in the best BAS assistance. To receive the benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not “pump” the brakes). Do not reduce brake pedal pressure unless braking is no longer desired. Once the brake pedal is released, the BAS is deactivated.
342 STARTING AND OPERATING prevent wheel lift due to other factors such as road Hill Descent Control (HDC) – If Equipped conditions, leaving the roadway or striking objects or This system maintains vehicle speed while descending other vehicles. hills during off-road driving situations. HDC will autoNOTE: Anytime the ESC system is in the “Full Off” matically apply the brakes to control downhill speed to mode, ERM is disabled.
STARTING AND OPERATING 343 Off” button for five seconds. Refer to “Electronic Stability Control (ESC)” in this section of the manual. WARNING! HDC operation can be overridden with brake application HDC is only intended to assist the driver in controlto slow the vehicle down below the HDC control speed. ling vehicle speed when descending hills.
344 STARTING AND OPERATING HSA Activation Criteria Disabling/Enabling HSA The following criteria must be met in order for HSA to If you wish to turn on or off the HSA system, it can be activate: done using the Customer Programmable Features in the Electronic Vehicle Information Center (EVIC). Refer to • Vehicle must be stopped. “Electronic Vehicle Information Center (EVIC)” in “Un• Vehicle must be on a 7% grade or greater hill. derstanding Your Instrument Panel” for further information.
STARTING AND OPERATING 345 5. Release the clutch pedal (if equipped). Electronic Stability Control (ESC) 6. Rotate the steering wheel one-half turn to the left. This system enhances directional control and stability of the vehicle under various driving conditions. ESC corrects for over-steering or under-steering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the over-steering or under-steering condition.
346 STARTING AND OPERATING Full On (Four-Wheel Drive Models) Or On (Two-Wheel Drive Models) WARNING! • The Electronic Stability Control (ESC) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. • ESC cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.
STARTING AND OPERATING 347 in deep snow, sand or gravel conditions and more wheel spin than ESC would normally allow is required to gain traction. To turn ESC on again, momentarily press the “ESC Off” switch. This will restore the normal “ESC On” mode of operation. NOTE: To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, it may be desirable to switch to the “Partial Off” mode by pressing the “ESC Off” switch.
348 STARTING AND OPERATING “ESC OFF” message will appear in the odometer. Press NOTE: The “ESC OFF” message will display and an and release the Trip Odometer button located on the audible chime will sound when the shift lever is placed into the PARK position from any other position, and then instrument cluster to clear this message. moved out of the PARK position. This will occur even if In this mode, ESC and TCS, except for the “limited slip” the message was previously cleared.
STARTING AND OPERATING 349 Malfunction Indicator Light” begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and The “ESC Activation/Malfunction Indicator driving to the prevailing road conditions. Light” in the instrument cluster will come on when the ignition switch is turned to the ON NOTE: position. It should go out with the engine • The “ESC Activation/Malfunction Indicator Light” running.
350 STARTING AND OPERATING NOTE: TIRE SAFETY INFORMATION Tire Markings • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
STARTING AND OPERATING 351 compact spare tires have the letter “T” or “S” molded • High flotation tire sizing is based on U.S. design into the sidewall preceding the size designation. Exstandards and it begins with the tire diameter molded ample: T145/80D18 103M. into the sidewall. Example: 31x10.5 R15 LT. Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....
352 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
STARTING AND OPERATING 353 Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side. Tires the outboard side, then you will find it on the inboard side of the tire. with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
354 STARTING AND OPERATING Tire Terminology And Definitions Term B-Pillar Cold Tire Inflation Pressure Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
STARTING AND OPERATING 355 Tire And Loading Information Placard Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
356 STARTING AND OPERATING Loading To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
STARTING AND OPERATING 357 2. Determine the combined weight of the driver and 6. If your vehicle will be towing a trailer, load from your passengers that will be riding in your vehicle. trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available 3. Subtract the combined weight of the driver and pascargo and luggage load capacity of your vehicle. sengers from XXX lbs or XXX kg. NOTE: 4.
358 STARTING AND OPERATING I nf or mat i onPr ov i dedby :
STARTING AND OPERATING 359 Safety WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
360 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering. Unequal tire pressures can cause erratic and unpredictable steering response.
STARTING AND OPERATING 361 CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the winter.
362 STARTING AND OPERATING Tire Pressures For High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle important. Increased tire pressure and reduced vehicle poorly.
STARTING AND OPERATING 363 the tire sidewall. Use all season tires only in sets of four; If you need snow tires, select tires equivalent in size and failure to do so may adversely affect the safety and type to the original equipment tires. Use snow tires only in sets of four; failure to do so may adversely affect the handling of your vehicle. safety and handling of your vehicle.
364 STARTING AND OPERATING Spare Tire Matching Original Equipped Tire And Wheel – If Equipped CAUTION! Your vehicle may be equipped with a spare tire and Because of the reduced ground clearance, do not take wheel equivalent in look and function to the original your vehicle through an automatic car wash with a equipment tire and wheel found on the front or rear axle compact, full size or limited-use temporary spare of your vehicle. This spare tire may be used in the tire installed.
STARTING AND OPERATING 365 Since this tire has limited tread life the original equip- Full Size Spare – If Equipped ment tire should be repaired (or replaced) and reinstalled The full size spare is for temporary emergency use only. on your vehicle at the first opportunity. This tire may look like the original equipped tire on the Do not install a wheel cover or attempt to mount a front or rear axle of your vehicle, but it is not.
366 STARTING AND OPERATING your original equipment tire, replace (or repair) the Tire Spinning original equipment tire and reinstall on the vehicle at the When stuck in mud, sand, snow, or ice conditions, do not first opportunity. spin your vehicle’s wheels above 30 mph (48 km/h) or for longer than 30 seconds continuously without stopWARNING! ping when you are stuck. Limited-use spares are for emergency use only. Installation of this limited-use spare tire affects vehicle handling.
STARTING AND OPERATING 367 These indicators are molded into the bottom of the tread Tread wear indicators are in the original equipment tires grooves. They will appear as bands when the tread depth to help you in determining when your tires should be becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. replaced.
368 STARTING AND OPERATING WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Information” placard for the size designation of your tire. The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.
STARTING AND OPERATING 369 WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have a collision resulting in serious injury or death.
370 STARTING AND OPERATING The suggested rotation method is the “rearward cross” shown in the following diagram. This rotation pattern The tires on the front and rear of your vehicle operate at does not apply to some directional tires that must not be different loads and perform different steering, driving, reversed. and braking functions. For these reasons, they wear at unequal rates. TIRE ROTATION RECOMMENDATIONS These effects can be reduced by timely rotation of tires.
STARTING AND OPERATING 371 also increase as the vehicle is driven - this is normal and there should be no adjustment for this increased presThe Tire Pressure Monitor System (TPMS) will warn the sure. driver of a low tire pressure based on the vehicle recommended cold placard pressure.
372 STARTING AND OPERATING driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information. CAUTION! For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 30 psi (207 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 27 psi (186 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressure to approximately 23 psi (158 kPa).
STARTING AND OPERATING 373 • Seasonal temperature changes will affect tire pressure, and the TPMS will monitor the actual tire pressure in • The TPMS is not intended to replace normal tire care the tire. and maintenance or to provide warning of a tire failure Base System or condition. NOTE: • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. • Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure.
374 STARTING AND OPERATING • Four Tire Pressure Monitoring Sensors Check TPMS Warnings • Tire Pressure Monitoring Telltale Light The Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds and remain on solid when a system fault is detected. The system fault will also sound a chime. If the ignition key is cycled, this sequence will repeat providing the system fault still exists. The Tire Pressure Monitoring Telltale Light will turn off when the fault condition no longer exists.
STARTING AND OPERATING 375 4. For each subsequent ignition key cycle, a chime will sound and the Tire Pressure Monitoring Telltale Light NOTE: Your vehicle is equipped with a compact spare will flash on and off for 75 seconds and then remain on wheel and tire assembly. solid. 1. The compact spare tire does not have a tire pressure 5. Once you repair or replace the original road tire and monitoring sensor.
376 STARTING AND OPERATING • Various Tire Pressure Monitoring System Messages, which display in the Electronic Vehicle Information The TPMS uses wireless technology with wheel rim Center (EVIC) mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve • Tire Pressure Monitoring Telltale Light stem, transmit tire pressure readings to the receiver Tire Pressure Monitoring Low Pressure Warnings module.
STARTING AND OPERATING 377 Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible and inflate all tires that are flashing on the graphic display to the vehicle’s recommended cold placard pressure value.
378 STARTING AND OPERATING Service TPMS Message The Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds, and remain on solid when a system fault is detected. The system fault will also sound a chime. The EVIC will display a “SERVICE TPM SYSTEM” message for a minimum of five seconds. This text message is then followed by a graphic display, with “- -“ in place of the pressure value(s) indicating which Tire Pressure Monitoring Sensor(s) is not being received.
STARTING AND OPERATING 379 The EVIC will also display a ⬙SERVICE TPM SYSTEM⬙ message for a minimum of five seconds when a system fault related to an incorrect sensor location fault is detected. In this case, the ⬙SERVICE TPM SYSTEM⬙ message is then followed with a graphic display with pressure values still shown.
380 STARTING AND OPERATING 2. If you install the compact spare tire in place of a road 4.
STARTING AND OPERATING 381 General Information FUEL REQUIREMENTS This device complies with Part 15 of the FCC rules and 2.0L And 2.4L Engine RSS 210 of Industry Canada. Operation is subject to the following conditions: This engine is designed to meet all emis• This device may not cause harmful interference.
382 STARTING AND OPERATING Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the Worldwide Fuel Charter, WWFC) which define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available. Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.
STARTING AND OPERATING 383 • disconnect and reconnect the battery to reset the engine controller memory Non-FFV vehicles are compatible with gasoline containing 10% ethanol (E10). Gasoline with higher ethanol More extensive repairs will be required for prolonged content may void the vehicle’s warranty. exposure to E-85 fuel.
384 STARTING AND OPERATING can be used at levels higher than those allowed in the United States. MMT is prohibited in Federal and California reformulated gasoline. Materials Added To Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and they would result in additional cost. Therefore, you should not have to add anything to the fuel.
STARTING AND OPERATING 385 NOTE: Intentional tampering with the emissions control system can result in civil penalties being assessed against you. Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: (Continued) WARNING! (Continued) • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill.
386 STARTING AND OPERATING ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door, on the left side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. After removing the gas cap, place the gas cap tether cable over a hook on the inside of the fuel door. This keeps the gas cap suspended away from and protects the vehicle’s surface.
STARTING AND OPERATING 387 CAUTION! WARNING! (Continued) • Damage to the fuel system or emission control system could result from using an improper fuel tank filler cap (gas cap). A poorly fitting cap could let impurities into the fuel system. • A poorly fitting gas cap may cause the “Malfunction Indicator Light (MIL)” to turn on. • To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. • Never add fuel when the engine is running.
388 STARTING AND OPERATING Loose Fuel Filler Cap Message Vehicle Certification Label If the vehicle diagnostic system determines that the fuel filler cap is loose or improperly installed, a “gASCAP” message will be displayed in the Odometer/Trip Odometer in the instrument cluster. Refer to “Instrument Cluster Description” in “Understanding Your Instrument Panel” for further information. Tighten the fuel filler cap properly and press the odometer/trip odometer RESET button to turn the message off.
STARTING AND OPERATING 389 Gross Vehicle Weight Rating (GVWR) Curb Weight The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, and cargo. The total load must be limited so that you do not exceed the GVWR. The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.
390 STARTING AND OPERATING Overloading can cause potential safety hazards and TRAILER TOWING shorten useful service life. Heavier suspension compo- In this section you will find safety tips and information nents do not necessarily increase the vehicle’s GVWR. on limits to the type of towing you can reasonably do with your vehicle.
STARTING AND OPERATING 391 exceed the GVWR. Refer to “Vehicle Loading/Vehicle Gross Axle Weight Rating (GAWR) Certification Label” in “Starting and Operating” for The GAWR is the maximum capacity of the front and rear further information. axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or Gross Trailer Weight (GTW) rear GAWR.
392 STARTING AND OPERATING than 10% or more than 15% of the trailer load. You must of hitches are the most popular on the market today and they are commonly used to tow small- and mediumconsider this as part of the load on your vehicle. sized trailers. Frontal Area The frontal area is the maximum height multiplied by the Weight-Distributing Hitch maximum width of the front of a trailer.
STARTING AND OPERATING 393 and trailer configuration / loading to comply with Gross Axle Weight Rating (GAWR) requirements. WARNING! • An improperly adjusted Weight Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision. • Weight Distributing Systems may not be compatible with Surge Brake Couplers. Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.
394 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission Frontal Area 2.0L Auto/Man 2.4L Auto/Man 2.4L Auto/Man with Trailer Tow Prep Package (AHC) 22 sq ft (2.04 sq m) 22 sq ft (2.04 sq m) 32 sq ft (3.0 sq m) Maximum GTW (Gross Trailer Wt.) 1,000 lbs (450 kg) 1,000 lbs (450 kg) 2,000 lbs (907 kg) Maximum Tongue Wt.
STARTING AND OPERATING 395 which will cause loss of control of the vehicle and trailer. Consider the following items when computing the Failure to load trailers heavier in front is the cause of weight on the rear axle of the vehicle: many trailer collisions. • The tongue weight of the trailer. Never exceed the maximum tongue weight stamped on • The weight of any other type of cargo or equipment your bumper or trailer hitch. put in or on your vehicle. • The weight of the driver and all passengers.
396 STARTING AND OPERATING Towing Requirements WARNING! To promote proper break-in of your vehicle drivetrain components, the following guidelines are recommended: CAUTION! • Do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven. The engine, axle or other parts could be damaged. • Then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle.
STARTING AND OPERATING 397 WARNING! (Continued) WARNING! (Continued) • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle automatic transmission in PARK.
398 STARTING AND OPERATING • Proper tire inflation pressures are essential to the safe Towing Requirements – Trailer Brakes and satisfactory operation of your vehicle. Refer to • Do not interconnect the hydraulic brake system or “Tires – General Information” in “Starting and Opervacuum system of your vehicle with that of the trailer. ating” for proper tire inflation procedures. This could cause inadequate braking and possible personal injury.
STARTING AND OPERATING 399 CAUTION! WARNING! (Continued) If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. • Towing any trailer will increase your stopping distance. When towing you should allow for additional space between your vehicle and the vehicle in front of you.
400 STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations.
STARTING AND OPERATING 401 NOTE: Using a lower gear ratio while operating the vehicle under heavy loading conditions, will improve Before setting out on a trip, practice turning, stopping, performance and extend transmission life by reducing and backing up the trailer in an area located away from excessive shifting and heat buildup. This action will also heavy traffic. provide better engine braking.
402 STARTING AND OPERATING Extended driving at high RPM should be avoided to prevent excess heat generation. A reduction in vehicle speed may be required to avoid extended driving at high RPM. Return to a higher gear or vehicle speed when grade and road conditions allow. Cooling System Electronic Speed Control – If Equipped When stopped for short periods of time, shift the transmission into NEUTRAL and increase engine idle speed. • Do not use in hilly terrain or with heavy loads.
STARTING AND OPERATING 403 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
404 STARTING AND OPERATING NOTE: Vehicles equipped with manual transmissions may be recreationally towed (flat towed) at any legal highway speed, for any distance, if the manual transmission is in NEUTRAL and the ignition key is in the ACC position. CAUTION! • DO NOT flat tow any vehicle equipped with an automatic transmission. Damage to the drivetrain will result. If these vehicles require towing, make sure all drive wheels are OFF the ground. • DO NOT dolly tow any 4WD vehicle.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 HAZARD WARNING FLASHERS . . . . . . . . . . .406 䡵 JUMP-STARTING PROCEDURES. . . . . . . . . . . .419 䡵 IF YOUR ENGINE OVERHEATS . . . . . . . . . . . .406 ▫ Preparations For Jump-Start . . . . . . . . . . . . . .420 䡵 JACKING AND TIRE CHANGING . . . . . . . . . .408 ▫ Jump-Starting Procedure . . . . . . . . . . . . . . . .421 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .408 䡵 FREEING A STUCK VEHICLE. . . . . . . . . . . . . .
406 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel, below the radio. potential for overheating by taking the appropriate action. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all direc- • On the highways — slow down.
WHAT TO DO IN EMERGENCIES 407 • You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If the pointer rises to the H (red) mark, the instrument cluster will sound a chime. When safe, pull over and stop the vehicle with the engine at idle.
408 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! (Continued) WARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack.
WHAT TO DO IN EMERGENCIES 409 Preparations For Jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 2. Turn on the Hazard Warning flasher. Spare Tire And Jack Stowage 3. Set the parking brake.
410 WHAT TO DO IN EMERGENCIES 6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if changing the right front tire, block the left rear wheel. NOTE: Passengers should not remain in the vehicle while the vehicle is being jacked.
WHAT TO DO IN EMERGENCIES 411 WARNING! (Continued) CAUTION! • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway, be extremely careful of motor traffic. • To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground. Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle.
412 WHAT TO DO IN EMERGENCIES NOTE: The jack handle attaches to the side of the jack 2. Loosen, but do not remove, the wheel nuts by turning with two attachment points. When the jack is partially them to the left one turn while the wheel is still on the expanded, the tension between the two attachment ground. points holds the jack handle in place. NOTE: There are front and rear jacking locations on each side of the body.
WHAT TO DO IN EMERGENCIES 413 6 Jacking Locations Front Jacking Location CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated.
414 WHAT TO DO IN EMERGENCIES 3. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to the wheel to be changed. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire.
WHAT TO DO IN EMERGENCIES 415 5. Remove the wheel nuts and pull the wheel and wheel covers, where applicable, off the hub. Install the spare wheel and wheel nuts with the cone shaped end of the nuts toward the wheel. Lightly tighten the nuts. WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury.
416 WHAT TO DO IN EMERGENCIES NOTE: The wheel cover is held on the wheel by the wheel nuts. When reinstalling the original wheel, properly align the wheel cover to the valve stem, place the wheel cover onto the wheel, then install the wheel nuts. 6. Lower the vehicle by turning the jack screw to the left. WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. 7.
WHAT TO DO IN EMERGENCIES 417 Road Tire Installation Vehicles Equipped With Wheel Covers 1. Mount the road tire on the axle. 2. Align the valve notch in the wheel cover with the valve stem on the wheel. Install the cover by hand. Do not use a hammer or excessive force to install the cover.
418 WHAT TO DO IN EMERGENCIES 3. Install the five wheel lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. the correct tightness, have them checked with a torque wrench by your authorized dealer or service station. 6.
WHAT TO DO IN EMERGENCIES 419 3. Lower the vehicle to the ground by turning the jack pack. Jump-starting can be dangerous if done improperly so please follow the procedures in this section carefully. handle counterclockwise. 4. Finish tightening the lug nuts. Push down on the NOTE: When using a portable battery booster pack wrench while at the end of the handle for increased follow the manufacturer’s operating instructions and leverage. Tighten the lug nuts in a star pattern until precautions.
420 WHAT TO DO IN EMERGENCIES Preparations For Jump-Start The battery in your vehicle is located in the front of the engine compartment below the air intake duct. To access the battery remove the air intake duct by turning the two finger screws, located on the radiator support.
WHAT TO DO IN EMERGENCIES 421 WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
422 WHAT TO DO IN EMERGENCIES CAUTION! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. NOTE: Remove Air Intake before proceeding with this Jump-Starting procedure. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 4.
WHAT TO DO IN EMERGENCIES 423 Once the engine is started, remove the jumper cables in the reverse sequence: 6. Disconnect the negative (-) jumper cable from the engine ground of the vehicle with the discharged battery. 7. Disconnect the negative end (-) of the jumper cable from the negative (-) post of the booster battery. CAUTION! Accessories that can be plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
424 WHAT TO DO IN EMERGENCIES CAUTION! CAUTION! Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the engine to idle with the shift lever in NEUTRAL for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of transmission failure during prolonged efforts to free a stuck vehicle.
WHAT TO DO IN EMERGENCIES 425 WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck and do not let anyone near a spinning wheel, no matter what the speed. 3.
426 WHAT TO DO IN EMERGENCIES 6. Insert the screwdriver or similar tool into the access 8. The vehicle may then be started in NEUTRAL. port, and push and hold the override release lever 9. Reinstall the shift lever override access cover. forward. 7. Move the shift lever to the NEUTRAL position. TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a towing service.
WHAT TO DO IN EMERGENCIES 427 Manual Transmission With Ignition Key • Front Wheel Drive (FWD) or Four-Wheel Drive (4WD) vehicles can be flat towed (all four wheels on the • Front Wheel Drive (FWD) vehicles can be towed with ground) with the transmission in NEUTRAL. the front wheels elevated or on a flatbed truck (all four wheels OFF the ground). • FWD vehicles can be towed with the front wheels elevated. • Four-Wheel Drive (4WD) vehicles must be towed on a flatbed truck (all four wheels OFF the ground).
428 WHAT TO DO IN EMERGENCIES All Transmissions CAUTION! If you must use the accessories (wipers, defroster, etc.) while being towed, the key must be in the ON/RUN position, not the ACC position. Make certain the transmission remains in NEUTRAL. Do not use sling-type equipment when towing. When securing the vehicle to a flatbed truck, do not attach to front or rear suspension components. Damage to your vehicle may result from improper towing.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMPARTMENT — 2.0L . . . . . . . . . .431 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . .440 䡵 ENGINE COMPARTMENT — 2.4L . . . . . . . . . .432 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . .440 䡵 ONBOARD DIAGNOSTIC SYSTEM — OBD II . .433 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . . .441 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . .433 ▫ Air Conditioner Maintenance . . . . . . . . . . . . .
430 MAINTAINING YOUR VEHICLE ▫ Automatic Transmission – If Equipped . . . . . .455 䡵 BULB REPLACEMENT . . . . . . . . . . . . . . . . . .470 ▫ Manual Transmission – If Equipped . . . . . . . .457 ▫ Headlamps . . . . . . . . . . . . . . . . . . . . . . . . .470 ▫ Rear Drive Assembly (RDA) – AWD/4WD Models Only . . . . . . . . . . . . . . .458 ▫ Fog Lamps . . . . . . . . . . . . . . . . . . . . . . . . . .471 ▫ Power Transfer Unit (PTU) – AWD/4WD Models Only . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 431 ENGINE COMPARTMENT — 2.
432 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 2.
MAINTAINING YOUR VEHICLE 433 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
434 MAINTAINING YOUR VEHICLE persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the MIL. Resolving the problem will turn the MIL light off. Normally, the OBD II system will be ready. The OBD II system may not be ready if your vehicle was recently serviced, recently had a dead battery or a battery replacement.
MAINTAINING YOUR VEHICLE 435 4. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced • The MIL will flash for about 10 seconds and then before going to the I/M station. The I/M station can fail return to being fully illuminated until you turn OFF your vehicle because the MIL is on with the engine the ignition or start the engine.
436 MAINTAINING YOUR VEHICLE DEALER SERVICE WARNING! Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these Service Manuals before attempting any procedure yourself. You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment.
MAINTAINING YOUR VEHICLE 437 Engine Oil CAUTION! • Failure to properly maintain your vehicle or perform repairs and service when necessary could result in more costly repairs, damage to other components or negatively impact vehicle performance. Immediately have potential malfunctions examined by an authorized dealer or qualified repair center. • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals.
438 MAINTAINING YOUR VEHICLE will result in the oil level at the full end of the indicator Engine Oil Selection range. For best performance and maximum protection under all types of operating conditions, the manufacturer only CAUTION! recommends engine oils that are API Certified and meet Do not overfill the engine. Overfilling the engine the requirements of Chrysler Material Standard MS-6395. will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature.
MAINTAINING YOUR VEHICLE 439 Synthetic Engine Oils CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New Vehicle Limited Warranty. You may use synthetic engine oils provided the recommended oil quality requirements are met, and the recommended maintenance intervals for oil and filter changes are followed.
440 MAINTAINING YOUR VEHICLE station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced with a new filter at every engine oil change. Engine Oil Filter Selection WARNING! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.
MAINTAINING YOUR VEHICLE 441 Maintenance-Free Battery WARNING! (Continued) Your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic maintenance required. WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water.
442 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion.
MAINTAINING YOUR VEHICLE 443 WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Warranty Information Book, located on the DVD, for further warranty information. • The air conditioning system contains refrigerant under high pressure.
444 MAINTAINING YOUR VEHICLE hood latching components to ensure proper function. Avoid using the wiper blades to remove frost or ice from When performing other underhood services, the hood the windshield. Keep the blade rubber out of contact with latch, release mechanism and safety catch should be petroleum products such as engine oil, gasoline, etc. cleaned and lubricated.
MAINTAINING YOUR VEHICLE 445 in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution.
446 MAINTAINING YOUR VEHICLE WARNING! (Continued) CAUTION! (Continued) • A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. • Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
MAINTAINING YOUR VEHICLE 447 NOTE: Intentional tampering with emissions control • Do not idle the engine with any spark plug wires systems can result in civil penalties being assessed disconnected or removed, such as when diagnostic against you. testing, or for prolonged periods during very rough idle or malfunctioning operating conditions. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe Cooling System and abnormal catalyst overheating.
448 MAINTAINING YOUR VEHICLE Coolant Checks Cooling System – Drain, Flush, And Refill Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed, and refilled with fresh engine coolant (antifreeze). Check the front of the A/C condenser for any accumulation of bugs, leaves, etc.
MAINTAINING YOUR VEHICLE 449 Selection Of Coolant CAUTION! (Continued) Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. CAUTION! • Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.
450 MAINTAINING YOUR VEHICLE period, it is important that you use the same engine Please note that it is the owner’s responsibility to maincoolant (antifreeze) throughout the life of your vehicle. tain the proper level of protection against freezing according to the temperatures occurring in the area where Please review these recommendations for using Organic the vehicle is operated. Additive Technology (OAT) engine coolant (antifreeze).
MAINTAINING YOUR VEHICLE 451 Disposal Of Used Engine Coolant WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure.
452 MAINTAINING YOUR VEHICLE The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for the coolant freeze point or replacing the engine coolant (antifreeze). Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven.
MAINTAINING YOUR VEHICLE 453 • Make sure that the coolant expansion bottle overflow hoses are not kinked or obstructed. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. WARNING! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage.
454 MAINTAINING YOUR VEHICLE when the pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. NOTE: If your vehicle is equipped with a manual transmission, the brake fluid reservoir supplies fluid to both the brake system and the clutch release system. The two systems are separated in the reservoir, and a leak in one system will not affect the other system.
MAINTAINING YOUR VEHICLE 455 WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a collision.
456 MAINTAINING YOUR VEHICLE only the manufacturer’s recommended transmission fluid which has the special friction coefficient additives necessary for proper steel belt traction on the drive and driven pulleys. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. It is important to maintain the transmission fluid at the correct level using the recommended fluid.
MAINTAINING YOUR VEHICLE 457 Routine fluid level checks are not required, therefore the transmission has no dipstick. Your authorized dealer can check your transmission fluid level using special service tools. If you notice fluid leakage or transmission malfunction, visit you authorized dealer immediately to have the fluid level checked. Operating the vehicle with an improper fluid level can cause severe transmission damage.
458 MAINTAINING YOUR VEHICLE NOTE: If contaminated with water, the fluid should be Frequency Of Fluid Change changed immediately. Refer to the “Maintenance Schedule” for the proper maintenance intervals. Rear Drive Assembly (RDA) – AWD/4WD Models Only Power Transfer Unit (PTU) – AWD/4WD Models Only Lubricant Selection Use only the manufacturers recommended transmission Lubricant Selection fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in Use only the manufacturer’s recommended fluid.
MAINTAINING YOUR VEHICLE 459 The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion Refer to the “Maintenance Schedule” for the proper resistance built into your vehicle. maintenance intervals. Appearance Care And Protection From Corrosion What Causes Corrosion? Frequency Of Fluid Change Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.
460 MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using MOPAR威 Car Wash or equivalent, or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumulated on your vehicle, use MOPAR威 Super Kleen Bug and Tar Remover or equivalent to remove. CAUTION! • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces.
MAINTAINING YOUR VEHICLE 461 • If you detect any stone chips or scratches in the paint, Wheel And Wheel Trim Care touch them up immediately. The cost of such repairs is • All wheels and wheel trim, especially aluminum and considered the responsibility of the owner. chrome plated wheels, should be cleaned regularly • If your vehicle is damaged due to a collision or similar with a mild soap and water to prevent corrosion.
462 MAINTAINING YOUR VEHICLE Stain Repel Fabric Cleaning Procedure – If Equipped • Do not use any harsh solvents or any other form of protectants on Stain Repel products. Stain Repel seats may be cleaned in the following man- Interior Care ner: Use MOPAR威 Total Clean or equivalent to clean fabric • Remove as much of the stain as possible by blotting upholstery and carpeting. with a clean, dry towel. Use MOPAR威 Total Clean or equivalent to clean vinyl upholstery.
MAINTAINING YOUR VEHICLE 463 solvents, detergents, or ammonia-based cleaners to clean To minimize the possibility of scratching the lenses and your leather upholstery. Application of a leather condi- reducing light output, avoid wiping with a dry cloth. To tioner is not required to maintain the original condition. remove road dirt, wash with a mild soap solution followed by rinsing. WARNING! Do not use volatile solvents for cleaning purposes.
464 MAINTAINING YOUR VEHICLE When cleaning the rear view mirror, spray cleaner on the Cleaning Plastic Instrument Cluster Lenses towel or rag that you are using. Do not spray cleaner The lenses in front of the instruments in this vehicle are directly on the mirror. molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. Instrument Panel Cover The instrument panel cover has a low glare surface which 1. Clean with a wet soft rag.
MAINTAINING YOUR VEHICLE 465 Replace the belts if they appear frayed or worn or if the buckles do not work properly. FUSES Integrated Power Module The Integrated Power Module is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini-fuses. A label that identifies each component may be printed on the inside of the cover. Refer to “Engine Compartment” in “Maintaining Your Vehicle” for further information.
466 MAINTAINING YOUR VEHICLE Cavity 3 4 5 6 7 8 Cartridge Fuse MiniFuse 10 Amp Red 10 Amp Red 20 Amp Yellow 10 Amp Red 30 Amp Green 30 Amp Green Description Rear Center Brake Light Switch Ignition Switch/ Occupant Classification Module Trailer Tow – If Equipped Power Mirror/ Steering Control Satellite Radio/Hands-Free Phone Ignition Off Draw Ignition Off Draw Cavity 9 Cartridge Fuse 40 Amp Green 10 12 13 14 I nf or mat i onPr ov i dedby : 40 Amp Green Description Power Seats 20 Amp Yellow 15
MAINTAINING YOUR VEHICLE 467 Cavity 16 Cartridge Fuse 17 18 19 20 21 22 MiniFuse 15 Amp Lt Blue 10 Amp Red 40 Amp Green Description Dome Lamp/ Sunroof/Rear Wiper Motor Wireless Control Module Auto Shutdown Relay Cavity 23 24 25 26 20 Amp Yellow 15 Amp Lt Blue 10 Amp Red 10 Amp Red Radio Amplifiers 27 Radio 28 Intrusion Module/ Siren – If Equipped Heating, AC/Compass 29 I nf or mat i onPr ov i dedby : Cartridge Fuse MiniFuse 15 Amp Lt Blue 15 Amp Lt Blue 10 Amp Red 15 Amp Lt Blue 10 Amp Red 10 A
468 MAINTAINING YOUR VEHICLE Cavity 30 Cartridge Fuse 31 32 30 Amp Pink 33 34 35 MiniFuse 20 Amp Yellow 10 Amp Red 10 Amp Red 30 Amp Pink 40 Amp Green Description Heated Seat – If Equipped Headlamp Washer – If Equipped Auto Shutdown Relay J1962 Conn/ Powertrain Control Module Antilock BrakeValve Antilock Brake Pump Cavity 36 37 Cartridge Fuse 30 Amp Pink MiniFuse 25 Amp Natural Description Headlamp/Washer Control/Smart Glass – If Equipped Diesel Fuel Heater – If Equipped CAUTION! • When inst
MAINTAINING YOUR VEHICLE 469 CAUTION! (Continued) • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it indicates a problem in the circuit that must be corrected. VEHICLE STORAGE air conditioning system at idle for about five minutes in the fresh air and high blower setting.
470 MAINTAINING YOUR VEHICLE Exterior Bulbs Low Beam Headlamp High Beam Headlamp Front Park/Turn Signal Lamp Front Side Marker Lamp Front Fog Lamp Center High Mounted Stop Lamp (CHMSL) Rear Tail/Stop Lamp Rear Turn Lamp Backup Lamp License Lamp BULB REPLACEMENT Bulb Number H11 9005 7444NA Headlamps 1. Raise the hood and locate the connector behind the headlamp.
MAINTAINING YOUR VEHICLE 471 Fog Lamps 1. Access lamp through the lower fascia cutout. 2. Remove electrical connector from bulb. 3. Remove bulb from housing. Rear Turn Signal And Backup Lamp 1. Remove the two push-pins from the taillamp housing. 2. Grasp the taillamp and pull firmly to disengage the lamp from the aperture panel. 3. Twist and remove socket from lamp. 4. Remove bulb from socket and replace.
472 MAINTAINING YOUR VEHICLE License Lamps 3. Pull bulb from socket. 1. Use a screw driver to gently pry against the side of the Center High-Mounted Stoplamp snap tab to remove the lamp from the liftgate. This light is an LED assembly. See your authorized dealer for replacement. 2. Rotate the socket 1/4 turn counterclockwise. FLUID CAPACITIES U.S. 13.6 Gallons Fuel (Approximate) Engine Oil with Filter 2.0L and 2.4L Engine (SAE 5W-20, 4.5 Quarts API Certified) Cooling System * 2.0L and 2.
MAINTAINING YOUR VEHICLE 473 FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of Chrysler Material Standard MS-12106. Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
474 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission (CVT) – If Equipped Manual Transmission – If Equipped Rear Drive Assembly (RDA) Power Transfer Unit (PTU) Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR威 CVTF+4威 Continuously Variable Transmission Fluid MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product. MOPAR威 Gear & Axle Lubricant SAE 80W-90 API GL 5 or equivalent non-synthetic product.
MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULE . . . . . . . . . . . . .476 ▫ Maintenance Chart. . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E S C H E D U L E S 8 476 MAINTENANCE SCHEDULES On Electronic Vehicle Information Center (EVIC) equipped vehicles, “Oil Change Required” will be disYour vehicle is equipped with an automatic oil change played in the EVIC and a single chime will sound, indicator system. The oil change indicator system will indicating that an oil change is necessary. remind you that it is time to take your vehicle in for scheduled maintenance.
MAINTENANCE SCHEDULES 477 M NOTE: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or twelve months, whichever comes first.
40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 4 5 6 7 8 9 10 11 12 13 14 15 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000 224,000 240,000 following pages for the required maintenance intervals.
Additional Maintenance Replace engine air cleaner filter. Replace air conditioning/cabin air filter. Replace spark plugs ** Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first. Replace rear drive assembly (RDA) fluid.
S C H E D U L E S 8 Replace power transfer unit (PTU) fluid. Change automatic transmission fluid and filter if using your vehicle for any of the following: police, taxi, fleet, or frequent trailer towing. Change the automatic transmission fluid and filter.
Change the manual transmission fluid if using your vehicle for any of the following: trailer towing, heavy loading, taxi, police, delivery service (commercial service), off-road, desert operation or more than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C). Inspect and replace PCV valve if necessary.
M 482 MAINTENANCE SCHEDULES A I ** The spark plug change interval is mileage based only, N yearly intervals do not apply. T E WARNING! N A N • You can be badly injured working on or around a C motor vehicle. Do only service work for which you E S C H E D U L E S have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . .485 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY). . . . . . . . . . . . . . . . . . .487 ▫ Prepare For The Appointment. . . . . . . . . . . . .485 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . .487 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . .485 䡵 WARRANTY INFORMATION . . . . . . . . . . . . .
484 IF YOU NEED CONSUMER ASSISTANCE 䡵 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES . . . . . . . . .491 ▫ Treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .491 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . .492 ▫ Temperature Grades. . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 485 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment Be Reasonable With Requests If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority. At many authorized dealer, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an appointment.
486 IF YOU NEED CONSUMER ASSISTANCE facilities, factory-trained technicians, special tools, and • Authorized dealer name the latest information to ensure the vehicle is fixed • Vehicle Identification Number (VIN) correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to an authorized dealer service manager first. Most matters can be re- Chrysler Group LLC Customer Center solved with this process. P.O.
IF YOU NEED CONSUMER ASSISTANCE 487 Mexico, D. F. Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered by Bell Canada. For TTY teletypewriter users, dial 711 and for Voice callers, dial 1 800 855-0511 to connect with a Bell Relay Service operator.
488 IF YOU NEED CONSUMER ASSISTANCE The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a service contract that is not a manufacturer’s service contract, and you require service after the manufacturer’s New Vehicle Limited Warranty expires, please refer to the contract documents, and contact the person listed in those documents.
IF YOU NEED CONSUMER ASSISTANCE 489 campaign. However, NHTSA cannot become involved in individual problems between you, your authorized MOPAR威 fluids, lubricants, parts, and accessories are dealer, and the manufacturer. available from an authorized dealer. They are recommended for your vehicle in order to help keep the vehicle To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– operating at its best. 9153), or go to http://www.safercar.
490 IF YOU NEED CONSUMER ASSISTANCE Diagnostic Procedure Manuals PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations.
IF YOU NEED CONSUMER ASSISTANCE 491 Call toll free at: Treadwear • 1–800–890–4038 (U.S.) The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
492 IF YOU NEED CONSUMER ASSISTANCE Traction Grades The Traction grades, from highest to lowest, are AA, A, B, and C. These grades represent the tire’s ability to stop on wet pavement, as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
2013 Compass 2013 OWNER’S MANUAL Chrysler Group LLC 13MK49-126-AA First Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
INDEX 10 I nf or mat i onPr ov i dedby :
494 INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . . .337 Adding Engine Coolant (Antifreeze) . . . . . . . . . . . .449 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .386 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . .444 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .384 Airbag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 Airbag Deployment . . . . . . . . . . . . . . . . . . . . . . . .71 Airbag Light . . .
INDEX 495 Fluid Level Check Fluid Type . . . . Gear Ranges . . . Special Additives Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .456 .455 .323 .456 .329 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .441 Keyless Transmitter Replacement (RKE) . . . . . . . .
496 INDEX Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .197 Cargo Load Floor . . . . . . . . . . . . . . . . . . . . . . . . .200 Cargo Tie-Downs . . . . . . . . . . . . . . . . . . . . . . . . .200 Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . .460 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . . . .112 Center High Mounted Stop Light . . . . . . . . . . . . . .472 Chains, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 497 Disposal of Used Coolant . . . . . Drain, Flush, and Refill . . . . . . Inspection . . . . . . . . . . . . . . . . Points to Remember . . . . . . . . . Pressure Cap . . . . . . . . . . . . . . Radiator Cap . . . . . . . . . . . . . . Selection of Coolant (Antifreeze) Corrosion Protection . . . . . . . . . . . Cruise Light . . . . . . . . . . . . . . . . . Cupholders . . . . . . . . . . . . . . . . . Customer Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
498 INDEX Electronic Stability Control (ESC) . . . . . . . . . . . . . .345 Electronic Vehicle Information Center (EVIC) . . . . . .228 Emergency, In Case of Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .408 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . .419 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .426 Emission Control System Maintenance . . . . . . . . . .434 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 499 Flooded Engine Starting . . . . . . . . . Fluid, Brake . . . . . . . . . . . . . . . . . . Fluid Capacities . . . . . . . . . . . . . . . Fluid Leaks . . . . . . . . . . . . . . . . . . Fluid Level Checks Automatic Transmission . . . . . . . Cooling System . . . . . . . . . . . . . Power Steering . . . . . . . . . . . . . Fluids, Lubricants and Genuine Parts Fog Lights . . . . . . . . . . . . . . . . . . . Folding Rear Seat . . . . . . . . . . . . . . Folding Rear Seat (Sedan) . . . . . . . .
500 INDEX High Beam/Low Beam Select Switch . . . . . . . . .165 Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .165 Replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . .470 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . .154 Heated Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . .111 Heated Seats. . . . . . . . . . . . . . . . . . . . . . . . . . . . .150 Heater . . . . . . .
INDEX 501 Ignition Key Removal . . . . . . . . . . . . . . . . . . . . . . .12 Immobilizer (Sentry Key) . . . . . . . . . . . . . . . . . . . .15 Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . . . .76 Information Center, Vehicle . . . . . . . . . . . . . . . . . .228 Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . . .107 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . . .212 Instrument Panel and Controls . . . . . . . . . . . . . . . .
502 INDEX High Beam Indicator . . . . . . . . . . . . . . . . . . . .214 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101 High Beam/Low Beam Select . . . . . . . . . . . . . .165 Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . .163 Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .217 License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .472 Anti-Lock . . . . . . . .
INDEX 503 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . .390 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .355 Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Automatic Door . . . . . . . . . . . . . . . . . . . . . . . .31 Child Protection . . . . . . . . . . . . . . . . . . . . . . . .33 Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Power Door . . . . . . . . . . . . . . . . . . . . . . . . . . .
504 INDEX MTBE/ETBE . . . . . . . . . . . . . . . . . . . . . . . . . . . .382 Multi-Function Control Lever . . . . . . . . . . . . . . . . .162 New Vehicle Break-In Period . . . . . . . . . . . . . . . . . .96 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . . . .39 Occupant Restraints (Sedan) . . . . . . . . . . . . . . . . . .64 Octane Rating, Gasoline (Fuel) . . . . . . . . . . . . . . . .381 Odometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .221 Trip . . . . . . . . . .
INDEX 505 Pets, Transporting. . . . . . . . . . . . . . . . . . . . . . . . . .95 Phone, Cellular . . . . . . . . . . . . . . . . . . . . . . . . . . .112 Phone, Hands-Free (Uconnect™). . . . . . . . . . . . . . .112 Placard, Tire and Loading Information . . . . . . . . . .355 Power Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 Outlet (Auxiliary Electrical Outlet) . . . . . . . . . .188 Steering . . . . . . . . .
506 INDEX Reminder, Seat Belt. . . . . . . . . . . . . . . . . . . . . . . . .59 Remote Control Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Security Alarm . . . . . . . . . . . . . . . . . . . . . . . . .18 Remote Keyless Entry (Sedan) . . . . . . . . . . . . . . . . .20 Remote Sound System (Radio) Controls . . . . . . . . .294 Remote Starting System. . . . . . . . . . . . . . . . . . . . . .26 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . . . . .469 Replacement Keys .
INDEX 507 Front Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . .55 Rear Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Untwisting Procedure . . . . . . . . . . . . . . . . . . . .52 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . .148 Heated . . .
508 INDEX Temperature Gauge, Engine Coolant . . . . . . . . . . . .217 Theft Alarm (Security Alarm). . . . . . . . . . . . . . . . . .18 Theft System (Security Alarm) . . . . . . . . . . . . . . . . .18 Tie Down Hooks, Cargo . . . . . . . . . . . . . . . . . . . .200 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . . . .171 Tire and Loading Information Placard . . . . . . . . . . .355 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . .350 Tires . . . . . . . . . . . . . . . .
INDEX 509 Pressure Monitor System (TPMS) Pressure Warning Light . . . . . . Quality Grading . . . . . . . . . . . Radial . . . . . . . . . . . . . . . . . . . Replacement . . . . . . . . . . . . . . Rotation . . . . . . . . . . . . . . . . . Safety . . . . . . . . . . . . . . . . . . . Sizes . . . . . . . . . . . . . . . . . . . . Snow Tires . . . . . . . . . . . . . . . Spare Tire . . . . . . . . . . . . . . . . Spinning . . . . . . . . . . . . . . . . . Trailer Towing . . . . . . . . . . . . .
510 INDEX Transmitter Battery Service (Remote Keyless Entry) . .25 Transmitter, Garage Door Opener (HomeLink威) . . . .176 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . . .367 Trip Computer . . . . . . . . . . . . . . . . . . . . . . . . . . .226 Trip Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . .221 Trip Odometer Reset Button. . . . . . . . . . . . . . . . . .219 Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . .164 Vehicle Certification Label . . . . .
INDEX 511 Window Fogging . . . . . . . . . . . . . . . . . . . . . . . . .308 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Windshield Defroster . . . . . . . . . . . . . . . . . . . . . . .99 Windshield Washers . . . . Windshield Wiper Blades . Windshield Wipers . . . . . Wiper Blade Replacement Wipers, Intermittent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
2013 Chrysler Group LLC 13MK49-126-AB 2nd Edition I nf or mat i onPr ovi dedby: Printed in U.S.A.
