SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications / Alterations . . . . . . . . . . . 7 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER Vehicle Identification Number (VIN) is found on the driver’s front corner of the instrument panel, visible through the windshield.
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS 1 WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . .12 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .12 ▫ Locking Doors With The Key . . . . . . . . . . . . . .14 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .14 䡵 Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 ▫ Replacement Keys . . . . . . . . . . . . . . . . . . . . . .16 ▫ Sentry Key Programming . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ “Child-Protection” Door Lock System (Rear Doors) . . . . . . . . . . . . . . . . . . . . . . . . . .21 䡵 Remote Keyless Entry — If Equipped . . . . . . . . .22 ▫ To Unlock The Doors And Liftgate . . . . . . . . . .22 ▫ To Lock The Doors . . . . . . . . . . . . . . . . . . . . .23 ▫ Horn Chirp Feature . . . . . . . . . . . . . . . . . . . . .23 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .23 ▫ To Program Transmitters . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Driver And Front Passenger Supplemental Restraint System (SRS) - Airbag . . . . . . . . . . . .43 ▫ Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .52 䡵 Engine Break-In Recommendations . . . . . . . . . . .60 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . .61 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place. Ignition Key Removal Automatic Transaxle Place the shift lever in PARK and make sure that the shift knob push button has returned to the out position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: If you try to remove the key before you place the lever in PARK, the key may become trapped temporarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake, brake pedal or the gear selector lever. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle. Locking Doors With The Key You can insert the key with either side up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 chip (transponder) embedded into them. Only keys that have been programmed to the vehicle can be used to start and operate the vehicle. The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regardless of whether or not the vehicle is locked or unlocked.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE All of the keys provided with your new vehicle have been programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle. At the time of purchase, the original owner is provided with a four digit PIN number. This number is required for dealer replacement of keys.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed. Repeat this procedure to program up to a total of 8 keys. If you do not have a programmed sentry key, contact your dealer for details.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If you turned the wheel to the right to engage the lock, you must turn the wheel slightly to the right to disengage it. If you turned the wheel to the left to engage the lock, turn the wheel slightly to the left to disengage it. Automatic Transaxle Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK and the shift knob push-button is out.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 WARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death. Power Door Locks — If Equipped A door lock switch is on each front door panel. Press this switch to lock or unlock the doors. CAUTION! An unlocked vehicle is an invitation to thieves.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Central Locking/Unlocking — If Equipped All vehicle doors and liftgate are locked with the first turn of the key to the LOCK position. The double unlock activation feature requires you to turn the key in the cylinder lock two times within five seconds to UNLOCK all vehicle doors and liftgate at once. You may turn this feature off and unlock all the doors and liftgate with one turn of the key by following these instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 2. Cycle the ignition switch ON/OFF four times ending in the OFF position. 3. Press the interior door lock switch to the LOCK position. To use the system, open each rear door and move the control UP to engage. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position. 4. A single chime will sound to signify that you have successfully completed the programming.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: For emergency exit with the system engaged, move the lock plunger up (unlocked position), roll down window and open the door with the outside door handle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 NOTE: You may turn off this feature and unlock all doors with one press of the button by following the procedure shown in the Central Locking/Unlocking paragraph. To Lock The Doors: Press and release the LOCK button to lock all doors and liftgate. The park lights will flash and the horn will chirp to acknowledge the signal.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Program Transmitters Up to four transmitters can be programmed to your vehicle. Your new vehicle was shipped with two transmitters. See your dealer for additional transmitters Additional transmitters can be programmed to the system by using the following procedure: 1. Insert the key into the ignition switch and turn the switch to the ON position. 2. Press and hold the Unlock button on the transmitter between four and ten seconds. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Transmitter Battery Service The recommended replacement battery is 2016 or its equivalent. 2 NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. 1. With the transmitter buttons facing down, use a thin coin to pry the two halves of the transmitter apart. Make sure not to damage the rubber gasket during removal. Separating Transmitter Halves 2. Remove and replace the batteries.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. To reassemble the transmitter case snap two halves together. Make sure there is an even gap between the two halves. Test transmitter operation. To set the alarm: SECURITY ALARM SYSTEM — IF EQUIPPED The system monitors the doors, liftgate, and ignition switch for unauthorized operation. 2. Lock the door using either the door key, power door lock switch, or the Keyless Entry Transmitter and close all doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 To disarm the system: Unlock a front door/liftgate using either the key or the Keyless Entry Transmitter. Security System Manual Override The system will not arm if you lock the doors using the manual door lock plunger. Starting the vehicle with a valid Sentry key will disarm the system. A valid key is one that is programmed to that particular vehicle. A valid key will disarm the system, an invalid key will trigger the alarm.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LIFTGATE NOTE: The key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate. To unlock the liftgate, insert the key into the lock and turn to the right. The liftgate can also be unlocked using the remote keyless entry or by activating the power door lock switches located on the front doors. The central locking/unlocking feature (if equipped) can also be activated from the liftgate key cylinder.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 WARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • If you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode. Gas props support the liftgate in the open position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a security measure, a Seat Back Emergency Release lever is built into the left side rear seat back latching mechanism. In the event of an individual being locked inside the liftgate area with the rear shelf panel in position 1 (Top) or position 2 (Middle), the left side rear seat back can be unlatched by pulling down on the glow-in-the-dark lever attached to the left rear seat back latching mechanism.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 NOTE: Make sure that the elastic loop is around the emergency release handle at all times. If the handle is pulled downward, entirely through the elastic loop, the handle will not return to its original position and the seat back may not operate properly. The window lock switch located between the window switches allows you to disable the rear window switches that are located at the back of the center floor console.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. Auto Down Feature The driver’s and passenger’s front window switches have an auto down feature. Press the window switch past the detent, release, and the window will go down automatically.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is above the back of the front seat, next to your arm. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your dealer and have it fixed. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Rear Center Lap/Shoulder Belt Retractor Lock-Out This feature is designed to lock the retractor whenever the rear seat back is not fully latched. This prevents someone from wearing the rear center lap/shoulder belt when the rear seat back is not fully latched. NOTE: • If the rear center lap/shoulder belt can not be pulled out, check that the rear seat back is fully latched.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front seat, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push up or down on the anchorage button to release the anchorage, and move it up or down to the position that serves you best. Adjusting Upper Shoulder Belt As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Seat Belts And Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. 2 Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the vehicle is equipped with side airbags, they are located inside the driver and front passenger seats, and their covers are also labeled SRS AIRBAG. Side Airbags WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Airbags inflate in moderate to high speed impacts. Along with seat belts and pretensioners, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. All occupants should wear their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4. If your vehicle has side airbags, do not lean against the door, airbags will inflate forcefully into the space between you and the door. WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 The front airbag system consists of the following: • Front Airbag Control Module (ACM) • AIRBAG Readiness Light • Driver and Passenger Front Airbag/Inflator Units • Unique Steering Wheel and Column • Unique Instrument Panel The Side Airbag System, on vehicles equipped, consists of the following: • AIRBAG Readiness Light (shared with the front airbag system) • Side Airbag in the driver’s seat • Side Airbag in the passenger’s seat • Interconnecting Wiring • A
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How The Airbag System Works • The front airbag control module determines if a frontal impact is severe enough to require the airbags to inflate. The front control module will not detect side, roll over, or rear collisions. The front airbag control module also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or ON positions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 • When the front airbag control module detects a collision requiring the front airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the front airbags. The front airbag covers separate and fold out of the way as the front airbags inflate to their full size. The front airbags fully inflate in about 50 milliseconds. This is only about half of the time it takes you to blink your eyes.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If A Deployment Occurs The airbag systems are designed to deploy when the airbag control modules detect a moderate-to-severe collision, to help restrain the driver and front passenger, and then immediately deflate. NOTE: A collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags and seat belt pretensioners replaced by an authorized dealer as soon as possible. Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately. Child Restraint Everyone in your vehicle needs to be buckled up at all times — babies and children, too.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. • Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward facing child restraint should only be used in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the seat belt has a switchable retractor, it will have a distinctive label. • In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle end of the belt several times to shorten it. Insert the latch plate into the buckle with the release button facing out.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Lower Anchors and Tether for CHildren (LATCH) Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tether for CHildren. The LATCH system provides for the installation of the child restraint without using the vehicle seat belt. All three rear seating positions have lower anchorages that are capable of accommodating LATCH-compatible child seats having flexible, webbing-mounted lower attachments.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child restraints systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the top tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products. Tether anchorage kits are also available for most older vehicles.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a child restraint top tether strap. Tether Strap Mounting Not all child restraint systems will be installed as we have described here. Again, carefully follow the instructions that come with the child restraint system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back. Transporting Pets Airbags deploying in the front seat could harm your pet.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty. If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front seat belt assemblies must be replaced after a collision. Rear seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc. If there is any question regarding belt or retractor condition, replace the belt. Airbag Light The light should come on and remain on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the LED is not lit during starting, have it checked.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .67 ▫ Phone Call Features . . . . . . . . . . . . . . . . . . . .76 ▫ Outside Mirror—Driver’s Side . . . . . . . . . . . . .68 ▫ Advanced Phone Connectivity . . . . . . . . . . . . .78 ▫ Outside Mirror—Passenger’s Side . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Folding Front Passenger Seat — If Equipped . . .84 ▫ Daytime Running Lights (Canada Only) . . . . . .97 ▫ Adjustable Head Restraints . . . . . . . . . . . . . . .85 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . . .97 ▫ Heated Seats — If Equipped . . . . . . . . . . . . . .86 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . . .97 ▫ Folding Rear Seat . . . . . . . . . . . . . . . . . . . . . .87 ▫ Turn Signals . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65 䡵 Electronic Speed Control — If Equipped . . . . . . 102 ▫ Reprogramming A Single Button . . . . . . . . . . 110 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . . 102 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 ▫ To Set At A Desired Speed . . . . . . . . . . . . . . . 103 䡵 Overhead Console — If Equipped . . . . . . . . . . . 111 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Electrical Outlet Use With Engine Off . . . . . . . 119 ▫ Position 1 (Top) . . . . . . . . . . . . . . . . . . . . . . 122 䡵 Console Features . . . . . . . . . . . . . . . . . . . . . . . 120 ▫ Position 2 (Middle) . . . . . . . . . . . . . . . . . . . . 123 䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 ▫ Position 3 (Floor) . . . . . . . . . . . . . . . . . . . . . 124 ▫ Front Seat Storage Bin — If Equipped . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustment. 3 Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle). The mirror should be adjusted while set in the day position (toward windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror—Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror. Outside Mirror—Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle. WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 Electric Remote-Control Mirrors — If Equipped Use the mirror select switch, located to the left of the steering column on the instrument panel, to adjust the view obtained in the outside mirrors. Press the L or R button for Left or Right mirror selection. Use the center off position to guard against accidentally moving a mirror position. 3 Select a mirror and press one of the four arrows for the direction you want the mirror to move.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on the sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights turn on automatically. Closing the mirror cover turns off the lights. Sun Visor Sliding Feature The sun visors may be pulled out to provide extended coverage of the side glass.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s microphone for private conversations. The UConnect™; phone book enables you to store up to 32 names and four numbers per name. This system is driven through your Bluetooth™ Hands-Free Profile cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ system can be used with any Hands Free Profile certified Bluetooth™ cellular phone. If your cellular phone has a different profile (i.e. headset profile), you will not be able to use any UConnect™ features. The UConnect™ system is fully integrated into your vehicle, including your vehicle’s stereo system. All voice prompts as well as the other party’s voice in a conversation will be played over your vehicle’s stereo system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 • You will be asked to say a four-digit pin number into the UConnect™ system which you will later need to enter into your cellular phone during the cellular phone pairing process. You can enter any four-digit pin number. You will not need to remember this pin number after the initial registration process. • The UConnect™ system will then prompt you to begin the cellular phone pairing process on your cellular phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt, says ⬙Call⬙ followed by the name and designation of a phonebook entry that you wish to dial. For example, you can say ⬙Call John Doe Work⬙. After you are finished adding an entry into the phonebook, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu. phonebook from which you can choose. To select one of the entries from the list, press the ⬙Voice Recognition⬙ button while the UConnect™ system is playing the desired entry and say ⬙Delete⬙.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Phonebook List Names⬙. • The UConnect™ system will play the names of all the phonebook entries. • To call one of the names in the list, press the ’Voice Recognition’ button during the playing of the desired name and say ⬙Call⬙. • The UConnect™ system will then prompt you as to number designation you wish to call. • The selected number will be dialed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, press the ’Phone’ button to place the current call on hold and answer the incoming call. To reject the incoming call, you can disregard the call and continue with your current conversation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Three-Way Calling To initiate three-way calling, press the ’Voice Recognition’ button while a call is in progress and make a second phone call. When the second call is established, press the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call. Call Termination To end a call in progress, press the ’Phone’ button. All calls in progress will be terminated.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 • You will be asked to say the name of the phone that you wish to delete. You can either say the name of the phone that you wish to delete or you can say ⬙All⬙ to delete all the phones. • After the ⬙Ready⬙ prompt, say ⬙Setup List Phones⬙ and the UConnect™ system will play the phone names of all paired cellular phones in order from highest priority to lowest priority.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnect™ System Features Barge In - Touch Tone Phone Inputs You can use your UConnect™ system to access a voice mail system, an automated service, or any other phone number that you can dial with any phone. When calling a number with your UConnect™ system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can push the ’Voice Recognition’ button and say the sequence you wish to enter followed by ⬙Send⬙.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g. the UConnect™ system will not repeat a phone number before you dial it). • Press the ’Phone’ button to begin. • After the ⬙Ready⬙ prompt, say ⬙Setup Confirmation⬙. The UConnect™ system will play the current confirmation prompt status and you will be given the choice to change it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Help If you need assistance at any prompt or if you want to know what your options are at any prompt, say ⬙Help⬙. The UConnect™ system will play all the options at any prompt if you ask for help. SEATS Front Seat Adjustment The adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position. Cancel At any prompt, you can say ⬙Cancel⬙ and you will be returned to the previous menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched. WARNING! Driver’s Power Seat Height Adjuster — If Equipped The power seat height adjuster is on the outboard side of the driver’s seat. Use this switch to move the seat up or down. • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Bucket Seats The recliner control is on the outboard side of the seat. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position. Recliner Control Lever Folding Front Passenger Seat — If Equipped The passenger front seat may be folded fully forward to provide additional cargo space.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the head restraints so that the upper edge is as high as practical. To raise the head restraint, pull up on the head restraint. To lower the head restraint, depress the button and push down on the head restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped This feature heats the front driver’s and passenger’s seats. The control for the heater is located on the outboard side of each seat. After turning on the ignition, you may choose from HIGH, or LOW heat settings. An indicator on the switch shows which setting has been chosen.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Folding Rear Seat To provide additional storage area, each rear seatback can be folded forward. Push and hold the buttons shown in the picture to fold down either or both seatbacks. Folding Rear Seat Button WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If the seatback is properly latched and the rear center lap/shoulder belt still does not operate properly check and see if the Automatic Locking retractor (ALR) system is activated. WARNING! The rear center lap/shoulder belt is equipped with a lock-out feature to ensure that the seatback is in the fully upright and locked position when occupied.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 • Push and hold the button on the seatback and fold down the rear seatback. • Pull the release handle located on the outboard side of the seat. Lift up the seat and tumble the seat forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Attach the elastic strap, located at the base of the seat cushion, onto the hook bar on the center trim panel to hold the seat in place. To return the rear seat to it’s upright latched position, rotate the seat cushion rearward to latch the seat. Then lift the seatback to its upright latched position. NOTE: The elastic strap should be reinstalled in the clip on the base of the seat cushion before returning the seat to its normal position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Rear Seat Removal The rear seats can be removed to provide more cargo space. • Pull the release lever located on the outboard side of the seat. Lift up the seat and tumble the seat forward. • Push and hold the button on the seatback and fold down the rear seatback.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Lift up the release levers to disengage the seat from the floor attachments. NOTE: Small rollers on the bottom of the folded seat and a handle at the top allow the seat to be easily moved when removed from the vehicle. To reinstall the rear seat, insert the seat into the floor attachments. Lower the release levers of the seat to latch the front floor attachments and rotate the seat rearward to latch the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Then move the safety catch located under the front edge of the hood, near the center and slightly to the right, and raise the hood. Use the hood prop rod clipped to the driver’s side of the engine compartment to secure the hood in the open position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. LIGHTS Overhead Console Map/Reading Lights — If Equipped These lights are mounted between the sun visors in the overhead console. Each light is turned ON by pressing the lens. Press the lens a second time to turn the light OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Interior Lights The interior lights come on when a door is opened. With the ignition key in the OFF position, the interior lights will automatically turn off in about 8 minutes if a door is left open or the dimmer control is left in the Dome light position. Turn the ignition switch ON to restore the interior light operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior light Defeat (OFF) Rotate the dimmer control to the extreme bottom “OFF” position. The interior lights will remain off when the doors are open. Parade Mode (Daytime Brightness Feature) Rotate the dimmer control to the first detent (white semi-circle). This feature brightens the odometer and radio display when the parking lights or headlights are on during daylight conditions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Daytime Running Lights (Canada Only) The front turn signal lights will come on as Daytime Running Lights whenever the ignition switch is on, the headlights are off, and the parking brake is off. The headlight switch must be used for normal night time driving. Lights-on Reminder If the headlights or parking lights are on after the ignition is turned OFF, a chime will sound to alert the driver when the driver’s door is opened.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The fog lights will only operate with the headlights on low beam. Selecting high beam headlights will turn off the fog lights. Turn Signals Move the Multi-Function Control Lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down without moving beyond the detent.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 If the lever is pulled while in the OFF position, the wipers will operate for two wipe cycles, then turn OFF. Mist Feature Push down on the wiper control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wiper Operation Move the lever upward to the second detent for Low speed wiper operation, or to the third detent for High speed operation Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. Move the lever to the DEL position, then select the delay interval by turning the end of the lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving. 3 TRACTION CONTROL SWITCH — IF EQUIPPED The TRAC indicator, located in the instrument cluster, will flash when the Traction Control System is in use.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Traction Control System indicator “TRAC OFF” will illuminate momentarily as a bulb check, each time the ignition switch is turned ON. This will occur even if you used the “TRAC OFF” switch to turn the system OFF. NOTE: The Traction Control System will make buzzing or clicking sounds when the system is in operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it. To Set At A Desired Speed: When the vehicle has reached the desired speed, press down on the lever and release. Release the accelerator and the vehicle will operate at the selected speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tapping “ACC/RES” once will result in a 2 mph (3 km/h) speed increase. Each time the lever is tapped, speed increases so that tapping the lever three times will increase speed by 6 mph (10 km/h), etc. To decrease speed while speed control is ON, push down and hold “COAST/SET”. Release the lever when the desired speed is reached, and the new speed will be set. Tapping the “COAST/SET” button once will result in a 1 mph (2 km/h) speed decrease.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Vehicles equipped with four speed automatic transaxles may experience a downshift to 3rd gear while climbing uphill or descending downhill. This downshift to 3rd gear is necessary to maintain vehicle set speed. push of a button. The Universal Transceiver operates off your vehicle’s battery and charging system; no batteries are needed. On steep hills a greater speed loss or gain may occur so it may be preferable to drive without speed control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features it could cause injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects. 2. Erase the factory test codes by pressing the two outside buttons. Release the buttons when the light in the Universal Transceiver begins to flash (about 20 seconds).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. The indicator light in the Universal Transceiver will begin to flash, first slowly and then rapidly. The rapid flashing indicates successful programming. If after 90 seconds the indicator light does not flash rapidly or goes out, return to step 1 and repeat the procedure. To train the other buttons, repeat steps 3 and 4. Be sure to keep your hand held transmitters in case you need to retrain the Universal Transceiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 NOTE: The assistance of a second person may make the following programming procedure quicker and easier. 1. Locate the training button on the garage door motor head unit. The exact location and color of the button may vary by garage door opener manufacturer. If you have difficulty in locating the training button, check your garage door opener manual, or call 1-800-355-3515 or, on the Internet, at www.homelink.com. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Universal Transceiver light will flash slowly and then rapidly when the programming is successful. NOTE: When programming such a garage door opener or gate, unplug the device to prevent possible damage to the garage door or gate motor. Operation Press and hold the desired button on the Universal Transceiver until the garage door or other device begins to operate. The light in the display shows that the signal is being transmitted.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. OVERHEAD CONSOLE — IF EQUIPPED This feature has a compass/temperature display and two map lamps. The overhead console is located on the headliner between the sun visors. 3 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass/Temperature Display This display provides the outside temperature and one of eight compass readings to indicate the direction the vehicle is facing. STEP Button Functions: WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible personal injury or property damage. Step Button 1. 2. 3. 4. 5.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Automatic Compass Calibration The automatic calibrating feature of the compass eliminates the need to calibrate the compass due to normal varying conditions. Compass Variance Selection Variance is the difference between magnetic North and geographic North. For proper compass function, the correct variance zone must be set. Refer to the variance map for the correct variance zone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Compass Calibration If the compass appears erratic, inaccurate, abnormal or the vehicle is new, you may calibrate the compass. Prior to calibrating the compass make sure the proper zone is selected. Refer to “Magnetic Zone Selection”.Find an open area away from large metal objects. With the vehicle running, press and hold the STEP button for (about 10 to 15 seconds). The display will illuminate the CAL indicator.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Press and hold the button in the center of the sunroof switch to open the vent. The sunroof can be stopped at any position between closed and full vent. To close the sunroof from the vent position, press and hold the switch forward. Releasing the switch will stop the movement of the sunroof and the sunroof will remain in the partial vent position until the switch is pushed forward again.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The sunshade can be opened manually. It will also open as the sunroof opens. The sunshade cannot be closed if the sunroof is open. WARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE It will accept a cigar lighter unit, which is part of the optional Smokers Package. To preserve the heating element of the cigar lighter unit, do not hold the lighter in the heating position. As a child safety precaution, this outlet is powered by the ignition switch, only when the switch is in the ⬙ON⬙ or ⬙ACCESSORY⬙ positions. There are two optional power outlets. One is in the Accessory Switch Bank, in the center of the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 The second is in the right rear cargo area. Electrical Outlet Use With Engine Off CAUTION! Rear Power Outlet Since this outlet is remote from the driver, it is powered by the ignition switch, only when it is in the ⬙ON⬙ or ⬙ACCESSORY⬙ positions, to protect the battery against discharge. Note: Neither of the power outlets will accept a cigar lighter unit. They are intended only for accessory usage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES The console has two front cup holders, a coin holder, 12 volt power outlet and a front storage tray. There are additional cup holders; one is molded in the center of the console to hold large cups and the other is at the rear of the console to serve passengers in the rear seat. The floor console power outlet will also operate a conventional cigar lighter unit (if equipped with an optional Smoker’s Package).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 CAUTION! • Many accessories that can be plugged into the 12 volt power outlet, draw power from the vehicle’s battery, even when not in use; i.e. cellular phones, etc. Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power such as coolers, vacuum cleaners, lights, etc., will discharge the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage Pockets There are also Storage pockets located on each door trim panel. REAR SHELF PANEL The rear shelf panel attaches to guides in the rear cargo area. The rear shelf panel may be installed in one of five different positions. NOTE: The liftgate may be opened or closed with the rear cargo shelf panel in position 1, position 2, position 3 or position 4. WARNING! • To avoid tipping, lock the shelf securely in all positions.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Position 2 (Middle) Insert the front outboard corners of the shelf panel into the middle guides and slide forward. Press down on the back of the shelf panel to lock it into place. 3 Rear Shelf Panel Position 1 WARNING! Do not load objects on the shelf in position 1 (top). In an accident objects could strike occupants causing serious or fatal injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not load objects over 100 lbs (45 kg) in position 2 (middle). Failure to follow this warning could cause the shelf to collapse resulting in personal injury. Position 3 (Floor) Insert the front outboard corners of the shelf panel into the bottom guides and slide forward. NOTE: To carry items that may soil the carpeting, the rear shelf panel may be inverted in position 2 or position 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 WARNING! 2. Twist the knob on the underside of the panel and lower the shelf leg. When in the vertical position, the rear shelf panel should not be used as a barrier for large objects in the cargo area when the seatbacks folded down. In an accident objects could strike the seatbacks or occupants causing serious or fatal injury. 3 Position 5 (table) With the liftgate open the rear shelf panel can be moved rearward to act as a serving counter. 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Install the shelf leg into the liftgate latch area as labeled on the rear scuff plate. WARNING! Do not load objects over 100 lbs (45 kg) in position 5 (table). Failure to follow this warning could cause the shelf to collapse resulting in personal injury. ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 To adjust the crossbars with botton style releases, depress the button and slide the crossbar to the next locking position. Alternate sides until the crossbars are positioned correctly for your cargo and the stanchions are locked square to the slide rails. External racks do not increase the total load carrying capacity of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof rack “Cautions” when carrying cargo on your roof rack.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . . . 133 ▫ Two Types Of Signals . . . . . . . . . . . . . . . . . . 145 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 134 ▫ Electrical Disturbances . . . . . . . . . . . . . . . . . . 145 䡵 Instrument Cluster—Turbo, With AutoStick . . . . 135 ▫ AM Reception . . . . . . . . . . . . . . . . . . . . . . . 145 䡵 Instrument Cluster—Turbo, Without AutoStick . . 136 ▫ FM Reception . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Cassette Player Features . . . . . . . . . . . . . . . . 149 ▫ Tone Control . . . . . . . . . . . . . . . . . . . . . . . . 155 ▫ CD Changer Control Capability — If Equipped . . . . . . . . . . . . . . . . . . . . . . . 150 ▫ AM/FM Selection . . . . . . . . . . . . . . . . . . . . . 156 䡵 Sales Code RAZ—AM/ FM Stereo Radio With Cassette Tape Player, CD Player And CD Changer Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 ▫ Scan Button .
UNDERSTANDING YOUR INSTRUMENT PANEL 131 ▫ Pinch Roller Release . . . . . . . . . . . . . . . . . . . 158 ▫ Noise Reduction . . . . . . . . . . . . . . . . . . . . . . 158 ▫ Operating Instructions — CD Player . . . . . . . . 159 ▫ Inserting The Compact Disc . . . . . . . . . . . . . . 159 ▫ Seek Button . . . . . . . . . . . . . . . . . . . . . . . . . 160 ▫ EJT CD (Eject) Button . . . . . . . . . . . . . . . . . . 160 ▫ FF/Tune/RW . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Satellite Radio — If Equipped . . . . . . . . . . . . . . 177 ▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . . 181 ▫ System Activation . . . . . . . . . . . . . . . . . . . . . 178 ▫ Reception Quality . . . . . . . . . . . . . . . . . . . . . 181 ▫ Electronic Serial Number/Sirius Identification Number (ENS/SID) . . . . . . . . . . . . . . . . . . . . 178 䡵 Cassette Tape And Player Maintenance . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 133 INSTRUMENT PANEL FEATURES 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER
UNDERSTANDING YOUR INSTRUMENT PANEL 135 INSTRUMENT CLUSTER—TURBO, WITH AUTOSTICK 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER—TURBO, WITHOUT AUTOSTICK
UNDERSTANDING YOUR INSTRUMENT PANEL 137 INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Charging System Light This light shows the status of the electrical charging system. The light should come on briefly when the ignition is first turned ON and remain on briefly as a bulb check. If the light stays on or comes on while driving, it means that there is a problem with the charging system.
UNDERSTANDING YOUR INSTRUMENT PANEL 6. Engine Temperature Warning Light This light warns of an overheated engine condition. If the engine is critically hot, a warning chime will sound 10 times. After the chime turns off, the engine will still be critically hot until the light goes out. 7. Turn Signal Indicators The arrows will flash in unison with the exterior turn signal, when using the turn signal lever. NOTE: Turn signal bulbs are located in the Instrument Panel. (See page 98 for more information.
UNDERSTANDING YOUR INSTRUMENT PANEL 139 10. High Beam Indicator This light shows that the headlights are on high beam. Pull the turn signal lever toward the steering wheel to switch the headlights from high or low beam. 11. Tachometer The white area of the scale shows the permissible engine revolutions-per-minute (rpm x 1000) for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 12.
UNDERSTANDING YOUR INSTRUMENT PANEL 14. Brake System Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light comes on, it may indicate that the parking brake is applied, or there is a low brake fluid level. On vehicles equipped with Anti-lock brakes (ABS), it may also indicate an ABS malfunction that could lead to reduced braking performance. WARNING! Driving a vehicle with the brake light on is dangerous.
UNDERSTANDING YOUR INSTRUMENT PANEL 141 The light will flash when the Traction Control System is controlling traction. 16. Door Ajar Indicator This vacuum fluorescent display indicator illuminates the word “DOOR”, when a door is not completely closed. If the door is open for more than 8 minutes, the light will turn off. 17. Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven. The trip odometer shows the trip distance since the last reset. U.S.
UNDERSTANDING YOUR INSTRUMENT PANEL 20. Airbag Light The light comes on and remains on for 6 to 8 seconds as a bulb check when the ignition switch is first turned ON. If the light does not come on during starting, stays on, or comes on while driving, have the system checked by an authorized dealer. (See page 52 for more information.) 21. Trac Off Light — If Equipped The TRAC OFF light will illuminate momentarily as a bulb check when the ignition switch is first turned ON.
UNDERSTANDING YOUR INSTRUMENT PANEL 143 Certain conditions such as a loose or missing gas cap, poor fuel quality, etc. may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations the vehicle will drive normally and will not require towing.
UNDERSTANDING YOUR INSTRUMENT PANEL 27. Odometer/Trip Odometer Reset Knob Press the knob to switch between the odometer and trip odometer. While the trip odometer is being displayed, press and hold this knob for a few seconds to reset the trip odometer to zero miles/kilometers. Clock Setting Procedure ELECTRONIC DIGITAL CLOCK 2. Press the H button to set hours or the M button to set minutes. The time setting will increase each time you press a button.
UNDERSTANDING YOUR INSTRUMENT PANEL 145 you understand and save you concern about these “apparent” malfunctions, you must understand a point or two about the transmission and reception of radio signals. AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs. Two Types of Signals There are two basic types of radio signals...
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RBB—AM/FM STEREO RADIO WITH CASSETTE TAPE PLAYER AND CD CHANGER CAPABILITY Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 147 Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection. Holding the button will bypass stations without stopping until you release it. Tune Press the TUNE control up or down to increase or decrease the frequency.
UNDERSTANDING YOUR INSTRUMENT PANEL Press the AUDIO button and BASS will be displayed. Press the SEEK + or SEEK – to increase or decrease the Bass tones. Press the AUDIO button a second time and TREB will be displayed. Press the SEEK + or SEEK – to increase or decrease the Treble tones. Press the AUDIO button a third time and BAL will be displayed. Press the SEEK + or SEEK – to adjust the sound level from the right or left side speakers. Press the AUDIO button a fourth time and FADE will be displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL 149 Cassette Player Features With ignition OFF and the sound system OFF, you can eject the tape cassette by pushing the EJECT button. The SEEK symbol appears on the display when Music Search is in operation. Music Search shuts off automatically when a selection has been located. You can turn the tape player ON by inserting a cassette or activating the MODE button (with a cassette in the radio), but only when the ignition and radio are on.
UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Cassette Mode) Pressing this button while playing a cassette tape will change the side of the tape being played. NR (Noise Reduction) Pushing the Number 2 Pre-set button when a tape is playing deactivates the Dolby Noise Reduction System*. When Dolby is ON, the NR symbol appears on the display. Each time a tape is inserted the Dolby will turn ON. * “Dolby” noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
UNDERSTANDING YOUR INSTRUMENT PANEL 151 Fast Forward And Rewind Buttons Press and hold the FF button for fast forward. Press and hold the RW button for fast reverse. The audio output can be heard when fast forward and fast reverse are activated. Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an interesting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer.
UNDERSTANDING YOUR INSTRUMENT PANEL An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following reasons: • Excessive vibration SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER AND CD CHANGER CONTROLS • Disc inserted upside down • Damaged disc • Water condensation on optics RAZ Radio Operating Instructions — Radio NOTE: Power to operate the radio is controlled by the ignition switch.
UNDERSTANDING YOUR INSTRUMENT PANEL 153 Power Switch, Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. The volume will be displayed and continuously updated while the button is pressed. Seek Button (Radio Mode) Press and release the Seek button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down.
UNDERSTANDING YOUR INSTRUMENT PANEL PTY (Program Type) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off. Pressing the PTY button within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broadcast PTY information.
UNDERSTANDING YOUR INSTRUMENT PANEL 155 By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If no station is found with the selected PTY program type, the radio will return to the last preset station.
UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received. Scan Button Pressing the SCAN button causes the tuner to search for the next station, in either AM or FM, pausing for 5 seconds at each listenable station before continuing to the next. Pressing the AM/FM button continues the search in the alternate frequency band.
UNDERSTANDING YOUR INSTRUMENT PANEL 157 To Change From Clock To Radio Mode Press the Time button to change the display between radio frequency and time. Operating Instructions — Tape Player Insert the cassette with the exposed tape side toward the right and the mechanical action of the player will gently pull the cassette into the play position. NOTE: When subjected to extremely cold temperatures, the tape mechanism may require a few minutes to warm up for proper operation.
UNDERSTANDING YOUR INSTRUMENT PANEL Tape Eject Press the EJT Tape button and the cassette will disengage and eject from the radio. Scan Button Press this button to play 10 seconds of each selection. Press the scan button a second time to cancel the feature. Changing Tape Direction If you wish to change the direction of tape travel (side being played), press the PTY button. The lighted arrow in the display window will show the new direction.
UNDERSTANDING YOUR INSTRUMENT PANEL 159 Operating Instructions — CD Player NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. CAUTION! This CD player will accept 4 3⁄4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. Inserting The Compact Disc The CD player contained within the radio is not a multi-disc changer, and will only accept one CD.
UNDERSTANDING YOUR INSTRUMENT PANEL Seek Button Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection. EJT CD (Eject) Button Press this button and the disc will unload and move to the entrance for easy removal. The unit will switch to the radio mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 161 MODE Press the MODE button to select between the tape player, CD player, or satellite radio (if equipped). Time Button Press this button to change the display from elapsed CD playing time to time of day. To select Satellite Radio (if equipped), press the MODE button until the word SIRIUS appears. The following will be displayed in this order: After three seconds, the current channel name and number will be displayed for five seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL Disc Down/Program Button 5 Press the DISC down (button 5) button to play the previous disc. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display. Fast Forward And Rewind Buttons Press and hold the FF button for fast forward. Press and hold the RW button for fast reverse. The audio output can be heard when fast forward and fast reverse are activated.
UNDERSTANDING YOUR INSTRUMENT PANEL 163 SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. RBK Radio Seek Press and release the SEEK button to search for the next station in either the AM or FM mode.
UNDERSTANDING YOUR INSTRUMENT PANEL the radio will continue to tune until you release the button. The frequency will be displayed and continuously updated while the button is pressed. To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. SET 1 will show in the display window. Select the “1–5” button you wish to lock onto this station and press and release that button.
UNDERSTANDING YOUR INSTRUMENT PANEL 165 Press the AUDIO button a fourth time and FADE will be displayed. Press the SEEK + or SEEK – to adjust the sound level between the front and rear speakers. Press the AUDIO button again or wait 5 seconds to exit setting tone, balance, and fade. AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received.
UNDERSTANDING YOUR INSTRUMENT PANEL Inserting The Compact Disc CAUTION! This CD player will accept 4 3⁄4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day. If the power is ON, the unit will switch from radio to CD mode and begin to play when you insert the disc.
UNDERSTANDING YOUR INSTRUMENT PANEL 167 FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Random Play — RND/Program Button 4 Press the RND (button 4) button while the CD is playing to activate Random Play. This feature plays the tracks on the selected disc in random order to provide an interesting change of pace. Satellite Radio (if equipped).
UNDERSTANDING YOUR INSTRUMENT PANEL Disc Up/Program Button 1 Press the DISC up (button 1) button to play the next available disc. Disc Down/Program Button 5 Press the DISC down (button 5) button to play the previous disc. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display. Fast Forward And Rewind Buttons Press and hold the FF button for fast forward. Press and hold the RW button for fast reverse.
UNDERSTANDING YOUR INSTRUMENT PANEL 169 A CD HOT symbol indicates the player is too hot. CD HOT will pause the operation. Play can be resumed when the operating temperature is corrected or another MODE is selected.
UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation Power/Volume Control Press the PWR/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio. Mode Press the MODE button repeatedly to select between AM, FM, the CD changer and Sirius Satellite Radio™ (if equipped). The display will show ST when a stereo station is received.
UNDERSTANDING YOUR INSTRUMENT PANEL 171 To Set The Radio Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET RND button. SET 1 will show in the display window. Select the “1–6” button you wish to lock onto this station and press and release that button. If a button is not selected within 5 seconds after pressing the SET RND button, the station will continue to play but will not be locked into pushbutton memory.
UNDERSTANDING YOUR INSTRUMENT PANEL Time Button Press the TIME button to change the display between radio frequency and time. General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the Power / Volume control pushed ON before the CD player will operate.
UNDERSTANDING YOUR INSTRUMENT PANEL 173 If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. LOAD/ EJT — Load Press the LOAD/ EJT button and the button with the corresponding number where the CD is being loaded. After the radio displays “load” insert the CD into the player.
UNDERSTANDING YOUR INSTRUMENT PANEL Scan Press the Scan button to scan through each track on the CD currently playing. FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Random Play — SET / RND Press the RND button while the CD is playing to activate Random Play. This feature plays the tracks on the disc in random order to provide an interesting change of pace.
UNDERSTANDING YOUR INSTRUMENT PANEL 175 Program Type Information Jazz Foreign Language News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Radio Display Inform Jazz Language News Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R&B Sports Program Type Talk Top 40 Weather Radio Display Talk Top 40 Weather By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to
UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SCAN button when the PTY icon is displayed, the radio will stop at every PTY station on the band and list each corresponding program type in the radio display. Time Press the TIME button to change the display from elapsed CD playing time to time of day. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual.
UNDERSTANDING YOUR INSTRUMENT PANEL 177 SALES CODE RB1—AM/FM STEREO RADIO WITH DVD/GPS NAVIGATION SYSTEM variety of destinations and routes. Refer to your “Navigation User’s Manual” for detailed operating instructions. NOTE: If your vehicle is not equipped with the CD Changer option, you will not be able to use the Navigation system and the CD Player simultaneously. Always remove the Navigation DVD before inserting another disc.
UNDERSTANDING YOUR INSTRUMENT PANEL System Activation To activate your Sirius Satellite Radio service, call the toll-free number 888-539-7474, or visit the Sirius web site at www.sirius.com. Please have the following information available when activating your system: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID). 2. Credit card information. 3. Your Vehicle Identification Number.
UNDERSTANDING YOUR INSTRUMENT PANEL 179 mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed. Selecting Satellite Mode in RBB, RAH and RBK Radios Press the MODE button repeatedly until ⬙S A⬙ appears in the display. A CD or tape may remain in the radio while in the Satellite radio mode. Selecting Satellite Mode in RBP, RBU, RAZ, RB1 and RBQ Radios Press the MODE button repeatedly until the word ⬙SIRIUS⬙ appears in the display.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Channels that may contain objectionable content can be blocked. Contact Sirius Customer Care at 888-5397474 to discuss options for channel blocking or unblocking. Please have your ESN/SID information available. Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory. These satellite channel pre-set stations will not erase any AM or FM pre-set memory stations.
UNDERSTANDING YOUR INSTRUMENT PANEL 181 Satellite Antenna To ensure optimum reception, do not place items on the roof around the rooftop antenna location. Metal objects placed within the line of sight of the antenna will cause decreased performance. Larger luggage items should be placed as far forward as possible. Do not place items directly on or above the antenna. Reception Quality Satellite reception may be interrupted due to one of the following reasons.
UNDERSTANDING YOUR INSTRUMENT PANEL 5. A loose tape should be corrected before use. To rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the required directions. CD/DVD DISC MAINTENANCE To keep the CD/DVD discs in good condition, take the following precautions: Maintain your cassette tape player. The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played.
UNDERSTANDING YOUR INSTRUMENT PANEL 183 RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL The controls are as follows: Fan and Air conditioning Control Use this control to regulate the amount of air forced through the system in any mode you select. The fan speeds to the left of the OFF position are for Air Conditioning. Choosing one of these speeds turns on the air conditioning compressor. The fan speed increases as you move the control to the left from the OFF position.
UNDERSTANDING YOUR INSTRUMENT PANEL 185 Bi-Level Air is directed through the panel and floor outlets. NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. Floor Air is directed through the floor outlets and side window demist outlets with a small amount through the defrost outlet.
UNDERSTANDING YOUR INSTRUMENT PANEL on the outer edge of each instrument panel outlet grille opens or closes a shutter to turn airflow on or off through that outlet. NOTE: For maximum airflow to the rear seat passengers, the center instrument panel outlets can be aimed, so that the left center outlet is directed toward the right rear passenger and the right center outlet is directed toward the left rear passenger.
UNDERSTANDING YOUR INSTRUMENT PANEL 187 This control only operates in the Outside Air and Recirculate modes; there is no in between position. Do not place the control between these positions. NOTE: Continuous use of the recirculate mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended. In cold or damp weather, the use of the Recirculate position will cause windows to fog on the inside because of moisture build up inside the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips
UNDERSTANDING YOUR INSTRUMENT PANEL 189 Window Fogging Vehicle side windows tend to fog on the inside in mild rainy or humid weather. To clear the windows, use the A/C, PANEL and blower controls. Direct the panel outlets toward the side windows. Do not use recirculate without A/C for long periods as fogging may occur.
UNDERSTANDING YOUR INSTRUMENT PANEL Side Window Demisters A side window demister outlet is at each end of the instrument panel. These nonadjustable outlets direct air toward the side windows when the system is in either the FLOOR, MIX, or DEFROST mode. The air is directed at the area of the windows through which you view the outside mirrors. REAR WINDOW FEATURES Electric Rear Window Defroster The push-button is located at the center of the instrument panel, below the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 191 CAUTION! To avoid damaging the electrical conductors, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the rear window. Labels can be peeled off after soaking with warm water. Rear Wiper/Washer Switch A push-button at the center of the instrument panel, below the radio, turns the rear wiper ON or OFF. When this switch is pressed the rear wiper will operate at a fixed interval of about 4 seconds between wipes.
UNDERSTANDING YOUR INSTRUMENT PANEL Adding Washer Fluid The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the rear of the engine compartment on the passenger side and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) and operate the system for a few seconds to flush out the residual water.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . . 196 䡵 Automatic Transaxle — If Equipped . . . . . . . . . 199 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . . 196 ▫ Brake/Transmission Interlock System . . . . . . . 200 ▫ Manual Transaxle . . . . . . . . . . . . . . . . . . . . . 196 ▫ Automatic Transaxle Ignition Interlock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 ▫ Normal Starting . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING ▫ AutoStick General Information . . . . . . . . . . . . 204 ▫ Tire Identification Number (TIN) . . . . . . . . . . 219 䡵 Manual Transaxle Operation . . . . . . . . . . . . . . . 205 ▫ Tire Loading And Tire Pressure . . . . . . . . . . . 220 ▫ 2.4 Liter Turbo— If Equipped . . . . . . . . . . . . . 207 䡵 Tires—General Information . . . . . . . . . . . . . . . . 224 ▫ Recommended Shift Speeds . . . . . . . . . . . . . . 207 ▫ Tire Pressure . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 195 䡵 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 233 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . . 237 䡵 Tire Rotation Recommendations . . . . . . . . . . . . 234 ▫ Fuel System Cautions . . . . . . . . . . . . . . . . . . 237 䡵 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . . 235 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . . . 238 ▫ 2.4L Standard Engine And 2.4L Standard Turbo Engine . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Automatic Transaxle The gear selector must be in the NEUTRAL or PARK position before you can start the engine. Apply the brakes before shifting to any driving gear. CAUTION! NOTE: You must press the brake pedal before shifting out of Park.
STARTING AND OPERATING 197 started within 3 seconds, slightly depress the accelerator pedal while continuing to crank. If the engine fails to start within 15 seconds, turn the ignition switch to the “OFF” position, wait 10 to 15 seconds, then repeat the normal starting procedure. WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way.
STARTING AND OPERATING WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. After Starting The idle speed will automatically decrease as the engine warms up.
STARTING AND OPERATING 199 TURBOCHARGER ⴖCOOL DOWNⴖ CHART Driving Conditions Idle Time (in minutes) Before Shut Down Normal Driving Not required. Aggressive Driving or Heavily Loaded 3 Trailer Tow 5 AUTOMATIC TRANSAXLE — IF EQUIPPED CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
STARTING AND OPERATING WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
STARTING AND OPERATING 201 Reset Mode The transaxle is monitored electronically for abnormal conditions. If a condition is detected that could cause damage, the transaxle shifts automatically into second gear. The transaxle remains in second gear despite the forward gear selected. Park (P), Reverse (R), and Neutral (N) will continue to operate. This second gear limp-in feature allows the vehicle to be driven to a dealer for service without damaging the transaxle.
STARTING AND OPERATING WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the vehicle into P (Park), remove the key from the ignition, and apply the parking brake. Once the key is removed from the ignition, the transmission shift lever is locked in the P (Park) position, securing the vehicle against unwanted movement.
STARTING AND OPERATING 203 “R” Reverse Shift into this range only after the vehicle has come to a complete stop. “N” Neutral Engine may be started in this range. “D” Overdrive This range should be used for most city and highway driving. It provides smoothest up shifts and down shifts and best fuel economy.
STARTING AND OPERATING AUTOSTICK — IF EQUIPPED Autostick is a driver-interactive transmission that offers manual gear shifting capability to provide you with more control. Autostick allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situations.
STARTING AND OPERATING 205 • Downshifts from third to second gear above 74 mph (119 km/h) and from second to first gear above 41 mph (66 km/h) will be ignored. • You can start out in first, second, or third gear. Shifting into fourth gear can occur only after vehicle speed reaches 15 mph (24 km/h). • The transmission will automatically downshift to first gear when coming to a stop. • Starting out in third gear is helpful in snowy or icy conditions.
STARTING AND OPERATING Fully depress the clutch pedal before you shift gears. As you release the clutch pedal, lightly depress the accelerator pedal. For most city driving you will find it easier to use only the lower gears. For steady highway driving with light accelerations, 5th gear is recommended. Never drive with your foot resting on the clutch pedal, or try to hold the vehicle on a hill with the clutch pedal partially engaged. This will cause abnormal wear on the clutch.
STARTING AND OPERATING 207 2.4 Liter Turbo— If Equipped the shifter lever all the way to the right to avoid accidentally selecting THIRD gear. Also, use care when selecting FIRST gear to avoid accidentally selecting REVERSE. When moving the shifter lever into REVERSE press the lever to the left until the resistance is overcome. When the ignition switch is in the ON position, a chime will sound to confirm that reverse has been selected and the backup lights will illuminate.
STARTING AND OPERATING TABLE 1-MANUAL TRANSAXLE NORMAL ACCELERATION AND CRUISE SHIFT SPEEDS IN mph (km/h) ENGINE MODE 1 to 2 2 to 3 3 to 4 4 to 5 SIZE Accel 15 (24) 25 (40) 40 (65) 45 (72) 2.4L Turbo Cruise 15 (24) 25 (40) 42 (68) 45 (72) 2.4L Accel 15 (24) 25 (40) 33 (53) 44 (70) NonTurbo Cruise 16 (26) 20 (32) 28 (45) 38 (61) For improved performance, your manual transaxle may be upshifted up to the maximum speeds listed in table 2 (within legal speed limits).
STARTING AND OPERATING 209 CAUTION! NOTE: This light only shows that the parking brake is on. It does not show the degree of brake application. If you skip more than one gear while downshifting or downshift at too high an engine speed, you could damage the engine, transmission, or clutch. If the parking brake is applied while the vehicle is moving, a chime will sound to alert the driver. The chime will sound up to 10 times or until the vehicle has returned to a stop.
STARTING AND OPERATING NOTE: The parking brake lever will not release unless the lever is pulled up slightly past its applied position. When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the automatic transaxle locking mechanism may make it difficult to move the selector out of Park. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on a uphill grade.
STARTING AND OPERATING 211 WARNING! • Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be injured. Children should be warned not to touch the parking brake or the gear selector. Don’t leave the keys in the ignition. A child could operate power windows, other controls, or move the vehicle. • Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and an accident.
STARTING AND OPERATING If either of the two hydraulic systems lose normal capability, the remaining system will still function with some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop. In addition, if the malfunction is caused by an internal leak, as the brake fluid in the master cylinder drops, the brake warning indicator will light.
STARTING AND OPERATING 213 WARNING! • Anti-lock system (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING TRACTION CONTROL — IF EQUIPPED The Traction Control System will improve acceleration and steering on slippery surfaces by reducing tire spin. The system reduces wheel slip and maintains traction at the driving (front) wheels by engaging the brake on the wheel that is losing traction. When this occurs the TRAC indicator light located above the instrument cluster odometer will flash. The system operates at speeds below 40 mph (64 km/h).
STARTING AND OPERATING 215 The system is always in the “ON” mode unless: • The TRAC OFF switch has been used to turn the system off; • There is a Anti-Lock Brake System malfunction; • There is a Traction Control System malfunction; • The system has been automatically deactivated to prevent damage to the brake system due to overheated brake temperatures. NOTE: Extended heavy use of Traction Control may cause the system to deactivate and turn on the TRAC OFF Light located in the instrument cluster.
STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • LT(Light Truck)-Metric tire sizing is based on U.S. design standards.
STARTING AND OPERATING 217 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (ie. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING 219 Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure for passenger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar. For vehicles other than passenger cars, the cold tire inflation pressures are listed on either the “B” pillar, the Certification Label or in the Tire Inflation Pressures brochure in the glove compartment.
STARTING AND OPERATING 221 Tire and Loading Information Placard 4) the cold tire inflation pressures for the front, rear and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
STARTING AND OPERATING lbs.” on the Tire and Loading Information placard. The combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX pounds” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3.
STARTING AND OPERATING 223 5
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 1.
STARTING AND OPERATING 225 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. Some vehicles may have Supplemental Tire Pressure Information for vehicle loads that are less than the maximum loaded vehicle condition.
STARTING AND OPERATING The pressure should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap–if equipped.
STARTING AND OPERATING 227 Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important.
STARTING AND OPERATING Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Always use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels). Never combine them with other types of tires. Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
STARTING AND OPERATING 229 Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result.
STARTING AND OPERATING WARNING! The limited use spare tires are for emergency use only. Installation of this limited use spare tire affects vehicle handling. With this tire, do not drive more than 60 mph (100 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assembly. Replace (or repair) the original tire at the first opportunity and reinstall it on your vehicle. Failure to do so could result in loss of vehicle control.
STARTING AND OPERATING 231 Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point.
STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that Replacing original tires with tires of a different size may result in false speedometer and odometer readings. specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.
STARTING AND OPERATING 233 Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-ofbalance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. TIRE CHAINS Due to limited clearance, tire chains are not recommended. CAUTION! Damage to the vehicle may result if tire chains are used. SNOW TIRES Some areas of the country require the use of snow tires during winter.
STARTING AND OPERATING Tire Rotation Recommendations Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on all season type tires.
STARTING AND OPERATING 235 FUEL REQUIREMENTS 2.4L Standard Engine and 2.4L Standard Turbo Engine Your vehicle is designed to meet all emission regulations and provide excellent fuel economy when using high quality regular unleaded gasoline with an octane rating of 87. The use of premium gasoline is not recommended. The use of premium gasoline will provide no benefit over high quality regular gasolines, and in some circumstances, may result in poorer performance. 2.
STARTING AND OPERATING Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifications (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications if they are available.
STARTING AND OPERATING 237 MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane number. Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT. Gasolines blended with MMT have shown to reduce spark plug life and reduce emission system performance in some vehicles. The manufacturer recommends using gasolines without MMT.
STARTING AND OPERATING • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your dealer for service assistance. • The use of fuel additives which are now being sold as octane enhancers is not recommended. Most of these products contain high concentrations of methanol.
STARTING AND OPERATING 239 • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. Fuel Filler Cap (Gas Cap) • Keep the liftgate closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle.
STARTING AND OPERATING CAUTION! WARNING! A poorly fitting gas cap may cause the Malfunction Indicator Light to turn on. • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel when the engine is running. This is in violation of most state and federal fire regulations and will cause the malfunction indicator light to turn on. CAUTION! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling.
STARTING AND OPERATING 241 WARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. VEHICLE LOADING Vehicle Loading Capacities Front Seat Occupants . . . . . . . . . . . . . . . . . . . . . . . 2 Rear Seat Occupants . . . . . . . . . . . . . . . . . . . . . . . . 3 Luggage . . . . . . . . . . . . . . . . . . . . . . . 115 lbs (52 kg) Rated Vehicle Capacity. . . . . . . . . . . . .
STARTING AND OPERATING Warranty To maintain warranty coverage, follow the requirements and recommendations in this manual concerning vehicles used for trailer towing. However the following conditions must be met: • The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range must be selected. • The maximum frontal area of the trailer cannot exceed 20 square feet (1.86 square meters).
STARTING AND OPERATING 243 • Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are recommended for motoring safety. • The automatic transaxle fluid and filter should be changed if you REGULARLY tow a trailer for more than 45 minutes of continuous operation. See Schedule “B” in section 8 of this manual for transaxle fluid change intervals. NOTE: Check the automatic transaxle fluid level before towing. NOTE: For vehicles equipped with Autostick.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 246 䡵 Driving On Slippery Surfaces . . . . . . . . . . . . . . 256 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . . 246 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . . 256 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . . 248 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER Do not use this emergency warning system when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and the vehicle locked. NOTE: With extended use, the flasher may wear down your battery.
WHAT TO DO IN EMERGENCIES 247 If the pointer rises to the H (red) mark, the instrument cluster will sound a chime. Pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the H (red) mark, turn the engine off immediately and call for service. NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off.
WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, refer to Section 7, Maintenance, of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous.
WHAT TO DO IN EMERGENCIES 249 Jack Location The jack and jack-handle are stowed behind the right rear side trim panel in the cargo area. Spare Tire Stowage The compact spare tire is stowed under the rear of the vehicle by means of a hook/basket mechanism. To remove or stow the compact spare, use the jack handle to rotate the “spare tire drive” nut. The nut is located under the rear scuff plate at the right rear of the cargo area, just inside the liftgate opening.
WHAT TO DO IN EMERGENCIES Spare Tire Removal Lift up the cover and fit the jack-handle over the drive nut. Rotate the nut to the left until you can remove the swivel hook from the stowage basket. Swing the basket down to remove the compact spare tire. CAUTION! The hook is designed for use with the jack handle only. Use of an air wrench or other power tools is not recommended and can damage the winch.
WHAT TO DO IN EMERGENCIES 251 Jacking Instructions 1. Remove the scissors jack and lug wrench from the stowage bag. NOTE: If equipped with a center cap that covers the wheel nuts, pry off the cap using the small end of the lug wrench. To reinstall the cap, make sure it is properly lined up before pushing it on to the wheel. 3. There are two front jacking locations on each side of the body and rear jacking locations located on the trailing arm bracket under the triangular cut out symbol.
WHAT TO DO IN EMERGENCIES Do not raise the vehicle until you are sure the jack is securely engaged. 4. Raise the vehicle by turning the jack screw to the right, using the swivel wrench. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it.
WHAT TO DO IN EMERGENCIES 253 6. Lower the vehicle by turning the jack screw to the left. 7. Finish tightening the nuts. Push down on the wrench while tightening the wheel nuts. Alternate nuts until each nut has been tightened twice. Correct wheel nut torque is 100 ft. lbs (135 N·m). If you doubt that you have tightened the nuts correctly, have them checked with a torque wrench by your dealer or at a service station. 8. Remove the wheel blocks and lower the jack until it is free.
WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES DUE TO A LOW BATTERY WARNING! Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be hurt by the fan. WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
WHAT TO DO IN EMERGENCIES 255 2. When boosting from a battery in another vehicle, park that vehicle within booster cable reach but without letting the vehicles touch. Set parking brake, place automatic transaxle in PARK (manual transaxle in NEUTRAL) and turn ignition to OFF for both vehicles. 3. Turn off the heater, radio and all unnecessary electrical loads. 4. Connect one end of a jumper cable to the positive terminal of the booster battery.
WHAT TO DO IN EMERGENCIES 5. Connect the other cable, first to the negative terminal of the booster battery and then to the negative jump start terminal, located near the hood release latch, of the vehicle with the discharged battery. Make sure you have a good contact. 6. If the vehicle is equipped with Sentry Key Immobilizer, turn the ignition switch to the ON position for 3 seconds before moving the ignition switch to the START position. 7.
WHAT TO DO IN EMERGENCIES 257 WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels. You could lose control of the vehicle and possibly have an accident. Accelerate slowly and carefully whenever there is likely to be poor traction (ice, snow, wet, mud, loose sand, etc.). Traction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface.
WHAT TO DO IN EMERGENCIES If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth between Reverse and First gear. Usually the least accelerator pedal pressure to maintain the rocking motion without spinning the wheels is most effective. WARNING! Fast spinning tires can be dangerous.
WHAT TO DO IN EMERGENCIES 259 Manual Transaxle Your vehicle may be towed if the gearshift lever is in NEUTRAL. If the transaxle is not operative, the vehicle must be towed with the front wheels off the ground. If it is necessary to use the accessories while being towed (wipers, defrosters, etc.), the key must be in the ON position, not the ACCESSORY position. Make certain the transaxle remains in NEUTRAL.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 2.4L Turbo Engine Compartment . . . . . . . . . . . . 264 ▫ Drive Belts — Check Condition And Tension . . 273 䡵 2.4L Engine Compartment . . . . . . . . . . . . . . . . 265 ▫ Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . 274 䡵 Onboard Diagnostic System — OBD II . . . . . . . . 266 ▫ Ignition Wiring System . . . . . . . . . . . . . . . . . 274 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Air Conditioner Maintenance . . . . . . . . . . . . . 279 ▫ Power Steering — Fluid Check . . . . . . . . . . . . 280 ▫ Front Suspension Ball Joints . . . . . . . . . . . . . . 280 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . . 281 ▫ Windshield Wiper Blades . . . . . . . . . . . . . . . . 281 ▫ Windshield Washer Reservoir . . . . . . . . . . . . . 282 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . . 283 ▫ Cooling System . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 263 ▫ Center High Mounted Stop Light . . . . . . . . . . 310 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312 䡵 Fluids And Capacities . . . . . . . . . . . . . . . . . . . 311 ▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313 䡵 Recommended Fluids, Lubricants And Genuine Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 2.
MAINTAINING YOUR VEHICLE 265 2.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 267 EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing.
MAINTAINING YOUR VEHICLE a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station.
MAINTAINING YOUR VEHICLE 269 NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. WARNING! Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance.
MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight. dipstick. Adding one quart of oil when the reading is at the MIN mark will result in a MAX reading on these engines.
MAINTAINING YOUR VEHICLE 271 • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C). • Trailer towing. • Taxi, Police or delivery service (commercial service). • Off-Road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel.
MAINTAINING YOUR VEHICLE Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API certified and meet the requirements of DaimlerChrysler Material Standard MS-6395. Engine Oil Viscosity (SAE Grade) SAE 5W-30 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy.
MAINTAINING YOUR VEHICLE 273 Materials Added To Engine Oils The manufacture strongly recommends against the addition of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental additives. Disposing of Used Engine Oil Care should be taken in disposing of used engine oil from your vehicle. Used oil, indiscriminately discarded, can present a problem to the environment.
MAINTAINING YOUR VEHICLE Special tools are required to properly measure tension and to restore belt tension to factory specifications. Also, check belt routing to make sure there is no interference between the belts and other engine components. Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device.
MAINTAINING YOUR VEHICLE 275 CAUTION! WARNING! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle.
MAINTAINING YOUR VEHICLE To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transaxle is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. • Do not idle the engine with any spark plug wires disconnected for prolonged period. Engine Timing Belt Replace the engine timing belt at the intervals described in the appropriate maintenance schedule.
MAINTAINING YOUR VEHICLE 277 NOTE: For vehicles with a Turbo engine, a small amount of oil accumulation in the air cleaner box is normal. The amount will depend on driving style. The air cleaner box should be cleaned out and a new make-upair filter element should be installed during the normal air filter maintenance procedure. WARNING! The air cleaner can provide a measure of protection in the case of engine backfire.
MAINTAINING YOUR VEHICLE WARNING! CAUTION! Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Battery gas is flammable and explosive. Keep flame or sparks away from the battery. Don’t use a booster battery or any other booster source with an output greater than 12 volts.
MAINTAINING YOUR VEHICLE 279 Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system.
MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment. NOTE: Use only manufacturer approved A/C System Sealers, Stop Leak Products, Seal Conditioners, Compressor Oil, or Refrigerants.
MAINTAINING YOUR VEHICLE 281 Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors,liftgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be removed.
MAINTAINING YOUR VEHICLE 2. Push the release tab shown in the illustration and slide the wiper blade assembly down along the arm. Gently place the wiper arm on the windshield. 3. Install the new blade assembly onto the wiper arm tip until it locks in place. Windshield Washer Reservoir The washer fluid reservoir is located in the rear of the engine compartment on the passenger side and should be checked for fluid level at regular intervals.
MAINTAINING YOUR VEHICLE 283 Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system, or if exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged; have a competent technician inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position. • You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool.
MAINTAINING YOUR VEHICLE 285 Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of old antifreeze solution.
MAINTAINING YOUR VEHICLE Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Years or 100,000 miles before replacement. To prevent reducing this extended maintenance period, it is important that you use the same coolant throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) coolant.
MAINTAINING YOUR VEHICLE 287 WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
MAINTAINING YOUR VEHICLE When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment.
MAINTAINING YOUR VEHICLE 289 • Do not change the thermostat for summer or winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions. Hoses And Vacuum/Vapor Harnesses Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage.
MAINTAINING YOUR VEHICLE Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Suggested service intervals can be found in the Maintenance Section. WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage.
MAINTAINING YOUR VEHICLE 291 NOTE: Often, fluids such as oil, power steering fluid, and brake fluid are used during assembly plant operations to ease the assembly of hoses to couplings. Therefore, oil wetness at the hose-coupling area is not necessarily an indication of leakage. Actual dripping of hot fluid when systems are under pressure (during vehicle operation) should be noted before a hose is replaced based on leakage.
MAINTAINING YOUR VEHICLE NOTE: If your vehicle is equipped with a manual transaxle, the Brake Fluid Reservoir supplies fluid to both the Brake System and the Clutch Release System. The two systems are separated in the reservoir and a leak in one system will not affect the other system. If the Brake Fluid Reservoir is low, and the brake system does not indicate any leaks or other problems, it may be a result of a leak in the Hydraulic Clutch Release System. See your local authorized dealer for service.
MAINTAINING YOUR VEHICLE 293 WARNING! Do not allow petroleum based fluid to contaminate the brake fluid as seal damage will result! Use of a brake fluid that may have a lower initial boiling point or unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident. Automatic Transaxle All front wheel drive vehicles have a transmission and differential assembly contained within a single housing.
MAINTAINING YOUR VEHICLE CAUTION! Using a transmission fluid other than the manufacturers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes. Refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE 295 If the fluid is cold, the fluid level should be between the lower two holes, into the area marked “LOW”. If the fluid level shows low, add sufficient transmission fluid to bring to the proper level. CAUTION! Transaxle Dipstick Location 6. Wipe the dipstick clean and reinsert until seated. Remove dipstick and note reading. If the fluid is hot, reading should be in the cross hatched area marked “HOT” between the upper two holes in the dipstick. Do not overfill.
MAINTAINING YOUR VEHICLE Maintenance schedule “A”—Non Turbo Charged Engines – No change necessary. Maintenance schedule “A”—Turbo Charged Engines – No change necessary. Maintenance schedule “B”—All Engines – Every 60,000 miles (96 000 km) change fluid and filter under the following conditions: • Police, taxi, limousine, commercial type operation, or trailer towing where the vehicle is driven regularly for more than 45 minutes of continuous operation.
MAINTAINING YOUR VEHICLE 297 Frequency Of Fluid Change Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of the vehicle. Fluid changes are not necessary unless the following conditions exist: which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and underbody protection.
MAINTAINING YOUR VEHICLE • Atmospheric fallout/industrial pollutants. Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar or other similar deposits have accumulated on your vehicle, wash it as soon as possible. • Use Mopar auto polish to remove road film and stains and to polish your vehicle. Take care never to scratch the paint.
MAINTAINING YOUR VEHICLE 299 • Use Mopar touch up paint on scratches or chips as soon as possible. Your dealer has touch up paint to match the color of your vehicle. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. • If you carry special cargo such as chemicals, fertilizers, deicer salt, etc.
MAINTAINING YOUR VEHICLE When cleaning extremely dirty wheels, care must be taken in the selection of tire and wheel cleaning chemicals and equipment to prevent damage to the wheels. Only Mopar Wheel Cleaners are recommended. DO NOT USE any of the items listed below which can damage your wheels and wheel trim. DO NOT USE: • Any abrasive cleaner • Any abrasive cleaning pad (such as steel wool) or abrasive brush • Any cleaner that contains an acid which can react with and discolor the chrome surface.
MAINTAINING YOUR VEHICLE 301 Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar Total Clean. Care should be taken to avoid soaking your leather upholstery with any liquid.
MAINTAINING YOUR VEHICLE Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters. Do not use scrapers or other sharp instruments which may scratch the elements. Instrument Panel Cover The instrument panel cover has a low glare surface which minimizes reflections in the windshield.
MAINTAINING YOUR VEHICLE 303 FUSES Underhood Fuses (Power Distribution Center) A Power Distribution Center is located in the engine compartment; next to the air cleaner filter. A label identifying the components and circuits is located on the underside of the cover.
MAINTAINING YOUR VEHICLE MINI FUSE 11 12 13 14 15 16 17 18 19 20 21 Amp/Color 10 Amp/Red 15 Amp/Blue 20 Amp/ Yellow 15 Amp/Blue 20 Amp/ Yellow 15 Amp/Blue 20 Amp/ Yellow 15 Amp/Blue 20 Amp/ Yellow Spare 20 Amp/ Yellow Items Fused Air Conditioning (A/C) Stop Lights Fuel Pump/Auto Shut Down (ASD) Horn Electronic Automatic Transaxle (ETAX) Hi Beam IOD 22 Spare Interior Fuses The fuse access panel is on the left side of the instrument panel next to the steering column.
MAINTAINING YOUR VEHICLE 305 FUSE 1 2 3 4 5 6 7 8 9 10 Amp/Color 25 Amp/ Natural 15 Amp/Blue 20 Amp/ Yellow 20 Amp/ Yellow 10 Amp/Red 10 Amp/Red 11 10 Amp/Red Exterior Lighting RKE/Door Locks 12 13 14 Power Height Adjust 15 Airbag Run Only B/U Electric Back Light (EBL) NEU SAF HVAC Blower 16 10 Amp/Red 10 Amp/Red 20 Amp/ Yellow 20 Amp/ Yellow 10 Amp/Red Items Fused Headlamp Switch 25 Amp/ Natural 15 Amp/Blue Fog Lamp (Domestic Only) 10 Amp/Red Airbag Run-ST 10 Amp/Red Cluster/RKE/SKIM 17 18 19
MAINTAINING YOUR VEHICLE CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it shows a problem in the circuit that must be corrected. VEHICLE STORAGE If you will not be using your vehicle for more than 21 days you may want to take steps to preserve your battery.
MAINTAINING YOUR VEHICLE 307 Overhead Reading Light (Overhead Console) . . . T1037 Overhead Reading Light (Rearview Mirror) . . . . . T192 Rear Cargo . . . . . . . . . . . . . . . . . . . . . . . . . . . . T906 Seat Belt Indicator . . . . . . . . . . . . . . . . . . . . . . . LED Security Alarm Indicator. . . . . . . . . . . . . . . . . . . LED Malfunction Indicator Light . . . . . . . . . . . . . . . . LED Temperature Indicator . . . . . . . . . . . . . . . . . . . . LED Trac (Active) Indicator . . . . .
MAINTAINING YOUR VEHICLE BULB REPLACEMENT Headlight Bulb Replacement CAUTION! Do not touch the new headlight bulb with your fingers. Oil contamination will severely shorten bulb life. 1. Remove the headlight access cover splash shield, located in the front wheel well opening. 2. Disconnect the electrical connector. 3. Rotate the socket to the left one quarter turn and replace the bulb.
MAINTAINING YOUR VEHICLE 309 Front Park/Turn Signal/Side Marker Lights Front Fog Lights — If Equipped 1. Remove the headlight access cover splash shield, located in the front wheel well opening. 1. Remove the fasteners attaching the lower splash shield to gain access to the fog light. 2. Rotate the socket to the left one quarter turn to replace and replace the bulb. 2. Twist and remove the bulb from the fog light housing. 3. Disconnect the electrical connector and replace bulb.
MAINTAINING YOUR VEHICLE 2. Twist the bulb socket 1/4 turn to remove it from the housing. Back Up Light Bulb 1. Remove the screws attaching the back up light to the rear fascia and remove the housing. 2. Remove the socket from the housing. 3. Pull the bulb out of the socket and replace. Center High Mounted Stop Light 1. Open the liftgate and remove the liftgate CHMSL cover. 2. Remove CHMSL lens from the housing by unlatching the two side latches. 3. Pull the bulb out of the socket and replace. 3.
MAINTAINING YOUR VEHICLE 311 FLUIDS AND CAPACITIES Fuel (Approximate) Engine Oil-With Filter 2.4 Liter Engines (Use API Certified SAE 5W-30 Engine Oil. Refer to your engine oil filler cap for correct SAE grade meeting DaimlerChrysler Material Standard MS-6395.) Cooling System * 2.4 Liter Engines (Mopar威 Antifreeze/Coolant 5 Year/100,000 Miles Formula) * Includes heater and coolant recovery bottle filled to MAX level. U.S. 15 Gallons Metric 56.7 Liters 5.0 qts 4.7 Liters 6.5 qts 6.
MAINTAINING YOUR VEHICLE RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluids, Lubricants and Genuine Parts Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Use API Certified SAE 5W-30 Engine Oil. Refer to your engine oil filler cap for correct SAE grade meeting DaimlerChrysler Material Standard MS-6395. Non Turbo—Mopar 4105409 or equiv.
MAINTAINING YOUR VEHICLE 313 Chassis Component Automatic Transmission Fluid. Manual Transmission Fluid. Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar威 ATF+4 Automatic Transmission Fluid or equivalent. Mopar威 ATF+4 Automatic Transmission Fluid or equivalent. Mopar威 DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids or equivalent.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . . . 316 ▫ Schedule “A”—Non Turbo . . . . . . . . . . . . . . . 329 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . . 316 ▫ Schedule “A”—Turbo . . . . . . . . . . . . . . . . . . 333 C ▫ Schedule “B”—All Engines . . . . . . . . . . . . . .
M A I N T E N A N C E 316 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 317 M • Taxi, police, or delivery service (commercial service).†〫 • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow schedule “B—All Engines” of the ⬙Maintenance Schedules⬙ section of this manual.
M 318 MAINTENANCE SCHEDULES A I At Each Stop for Fuel N T • Check the engine oil level about 5 minutes after a fully E warmed engine is shut off. Checking the oil level while N A the vehicle is on level ground will improve the accuN racy of the oil level reading. Add oil only when the C level is at or below the ADD or MIN mark. E S C H E D U L E S 8 • Check the windshield washer solvent and add if required. • Check all lights and all other electrical items for correct operation.
SCHEDULE “B”—ALL ENGINES 319 M A SCHEDULE “B”—ALL ENGINES Follow schedule “B”—All Engines if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an 〫. Change the manual transaxle fluid every 48,000 miles (77 000 km) if the vehicle is usually operated under one or more of the conditions marked with an †.
M A I N T E N A N C E 320 SCHEDULE “B”—ALL ENGINES NOTE: IF ANY of these apply to you then flush and replace the engine coolant every 102,000 miles (164,000 km) or 60 months, whichever comes first, and follow schedule “B—All Engines” of the ⬙Maintenance Schedules⬙ section of this manual.
SCHEDULE “B”—ALL ENGINES 321 M Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter, replace as necessary.* Inspect the Make-up air filter, replace as necessary.
M 322 SCHEDULE “B”—ALL ENGINES A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace as necessary.* Replace the Make-up air filter. Adjust the generator drive belt tension.
SCHEDULE “B”—ALL ENGINES 323 M Miles ( Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Change the brake fluid. If vehicle is used for trailer towing. Inspect the engine air cleaner filter, replace as necessary.* Change the manual transaxle fluid.† Inspect the Make-up air filter. Replace as necessary.
M 324 SCHEDULE “B”—ALL ENGINES A I N Miles T ( Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Replace the Make-up air filter. Adjust the generator drive belt tension.
SCHEDULE “B”—ALL ENGINES 325 M Miles 75,000 78,000 81,000 84,000 87,000 90,000 (Kilometers) (120 000) (125 000) (130 000) (135 000) (130 000) (144 000) Change engine oil and engine oil filter, if not reX X X X X X placed at 3 months. Rotate tires. X X X Inspect the brake linings. X Inspect the engine air cleaner filter and replace as X necessary.* Replace the engine air cleaner filter. X Replace the spark plugs. X Inspect the tie rod ends and boot seals. X Inspect the PCV valve and replace if necessary.
M 326 SCHEDULE “B”—ALL ENGINES A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not reA placed at 3 months. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Change the brake fluid. If vehicle is used for trailer towing. Inspect the engine air cleaner filter and replace as necessary.* Change the manual transaxle fluid.† Flush and replace the engine coolant, if not replaced at 60 months. Inspect the Make-up air filter, replace as necessary.
SCHEDULE “B”—ALL ENGINES 327 M Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. * Inspect the tie rod ends and boot seals. Replace the Make-up air filter. Adjust the generator drive belt tension. Change automatic transaxle fluid and filter.〫 Inspect the PCV valve and replace if necessary. *‡ Flush and replace the engine coolant at 120 months, if not replaced at 102,000 miles.
M A I N T E N A N C E S C H E D U L E S 8 328 SCHEDULE “B”—ALL ENGINES * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emissions warranty. ‡ This maintenance is not required if previously replaced. † This maintenance is required only for police, taxi, limousine type operation, or trailer towing. 〫 This maintenance is required only for police, taxi, limousine type operation, or trailer towing.
SCHEDULE “A”—NON TURBO 329 M SCHEDULE “A”—NON TURBO Miles (Kilometers ) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the Make-up air filter.
M 330 SCHEDULE “A”—NON TURBO A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace, if necessary.* Flush and replace the engine coolant at 60 months, if not done at 102,000 miles. Replace the Make-up air filter. Adjust the generator drive belt tension.
SCHEDULE “A”—NON TURBO 331 M Miles 72,000 78,000 84,000 90,000 96,000 102,000 (Kilometers) (115 000) (125 000) (134 000) (144 000) (154 000) (164 000) [Months] [72] [78] [84] [90] [96] [102] Change engine oil and engine oil filter. X X X X X X Rotate tires. X X X X X X Inspect the brake linings. X X Replace the engine air cleaner filter. X Replace the spark plugs. X Inspect the tie rod ends and boot seals. X Inspect the PCV valve and replace if necessary. X Not required if previously changed.
M 332 SCHEDULE “A”—NON TURBO A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Inspect the PCV valve and replace if necessary. * ‡ S C H E D U L E S 8 108,000 (173 000) [108] X X Replace the air cleaner filter. Replace the engine timing belt. * Flush and replace the engine coolant at 120 months, if not done at 102,000 miles. Replace the spark plugs and ignition cables. Replace the Make-up air filter.
SCHEDULE “A”—TURBO 333 M SCHEDULE “A”—TURBO Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs. Inspect the tie rod ends and boot seals. Replace the Make-up air filter. Adjust the generator drive belt tension.
M 334 SCHEDULE “A”—TURBO A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Flush and replace engine coolant at 60 months, if not replaced at 100,000 miles.
SCHEDULE “A”—TURBO 335 M Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Replace the Make-up air filter. Adjust the generator drive belt tension.
M 336 SCHEDULE “A”—TURBO A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Rotate tires. E Inspect the brake linings. S C H E D U L E S 8 Replace the engine air cleaner filter. Replace the spark plugs. Adjust the generator drive belt tension. Inspect the tie rod ends and boot seals. Inspect the PCV valve and replace if necessary. Not required if previously changed. * ‡ Flush and replace the engine coolant if not done at 60 months. Replace the Make-up air filter.
SCHEDULE “A”—TURBO 337 M Miles (Kilometers) [Month] Change engine oil and engine oil filter. Rotate tires. Inspect the PCV Valve and replace if necessary. * Replace the engine air cleaner filter. Replace the spark plugs and ignition cables. * This maintenance is recommended by the manufacturer to the owner but is not required to maintain the emissions warranty. ‡ This maintenance is not required if previously replaced.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340 ▫ Prepare For The Appointment . . . . . . . . . . . . 340 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 340 䡵 Reporting Safety Defects . . . . . . . . . . . . . . . . . . 345 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 345 䡵 Publication Order Forms . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE 341 Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to you selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service. The manufacturer’s dealers have the facilities, factory-trained technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner.
IF YOU NEED CONSUMER ASSISTANCE DaimlerChrysler Canada Inc. Customer Center P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone —(800) 465–2001 In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F.
IF YOU NEED CONSUMER ASSISTANCE 343 The manufacturer will not stand behind any service contract that is not the manufacturer’s Service Contract. It is not responsible for any service contract other than the manufacturer’s Service Contract. If you purchased a service contract that is not a manufacturer’s Service Contract, and you require service after your manufacturer’s new vehicle limited warranty expires, please refer to your contract documents, and contact the person listed in those documents.
IF YOU NEED CONSUMER ASSISTANCE U.S.
IF YOU NEED CONSUMER ASSISTANCE 345 MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer.
IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.
IF YOU NEED CONSUMER ASSISTANCE 347 Call Toll Free at 1–800–890–4038 (U.S.) or 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: www.techauthority.daimlerchrysler.com or www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following describes the tire grading categories established by the National highway Traffic Safety Administration.
IF YOU NEED CONSUMER ASSISTANCE WARNING! WARNING! The traction grade is based on braking (straightahead) traction tests and does not include cornering (turning) performance. The temperature grade is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
INDEX 10
INDEX ABS (Anti-Lock Brake) System . . . . . . . . . . . . . . 212 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 286 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 239 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 192 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 237 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 276 Air Conditioner Maintenance . . . . . . . . . . . . . . . 279 Air Conditioning Controls . . . . . . . . . . . . . . .
INDEX 351 Special Additives . . . . . . . . . . . . . . . . . . . . . . 296 Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . 143,204 Back-Up Lights . . . . . . . . . . . . . . . . . . . . . . . . . 310 Ball Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277 Keyless Transmitter Replacement . . . . . . . . . . . . 25 Belts, Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Caution, Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . 61 CD Changer . . . . . . . . . . . . . . . . . . . . . . 150,161,167 CD Player . . . . . . . . . . . . . . . . . . 159,163,165,169,172 CD Player Maintenance . . . . . . . . . . . . . . . . . . . 182 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . 70,183 Center High Mounted Stop Light . . . . . . . . . . . . 310 Central Door Locks . . . . . . . . . . . . . . . . . . . . . . . 20 Chains, Tire . . . . . . . . . . . . .
INDEX 353 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . 287 Points to Remember . . . . . . . . . . . . . . . . . 286,288 Pressure Cap . . . . . . . . . . . . . . . . . . . . . . . . . 286 Selection of Coolant . . . . . . . . . . . . . . . . . . . . 285 Corrosion Protection . . . . . . . . . . . . . . . . . . . . . 297 Crankcase Emission Control System . . . . . . . . . . 276 Cruise Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 Cup Holder . . . . . . . . . . . . . . . .
INDEX Emission Control System Maintenance . . . . . . 267,316 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264,265 Break-In Recommendations . . . . . . . . . . . . . . . . 60 Checking Oil Level . . . . . . . . . . . . . . . . . . . . . 269 Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284 Exhaust Gas Caution . . . . . . . . . . . . . . . . . . . . 238 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . 235 Jump Starting . . . . . . . . . . . . . . . . . . .
INDEX 355 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235,312 Adding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239 Additives . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311 Clean Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236 Filler Cap . . . . . . . . . . . . . . . . . . . . . . . . . 143,239 Filler Door . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 Filter . .
INDEX Headlights Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 308 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301 High Beam . . . . . . . . . . . . . . . . . . . . . . . . . 98,139 High Beam/Low Beam Select Switch . . . . . . . . . 98 Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 Heated Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 357 Key, Sentry . . . . . . . Key-In Reminder . . . Keyless Entry System Keys . . . . . . . . . . . Knee Bolster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 . . 14 . . 22 . . 12 47,49 Lane Change and Turn Signals . . . . . . . . . . . . . . 138 Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . . .
INDEX Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308 Theft Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Traction Control . . . . . . . . . . . . . . . . . 140,142,215 Turn Signal . . . . . . . . . . . . . . . . . . . . 96,98,138,309 Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Warning (Instrument Cluster Description) . . . . . 137 Loading Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 241 Tires . . . . . . . . . . . . . . . .
INDEX 359 Vanity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Modifications/Alterations, Vehicle . . . . . . . . . . . . . 7 Mopar Parts . . . . . . . . . . . . . . . . . . . . . . . . . 268,345 Multi-Function Control Lever . . . . . . . . . . . . . . . . 96 Navigation System . . . . . . . . . . . . . . . . . . . . . . . 177 New Vehicle Break-In Period . . . . . . . . . . . . . . . . 60 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . . . 33 Octane Rating, Gasoline . . . .
INDEX Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . 209 Passing Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Pets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Phone, Cellular . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Phone, Hands-Free . . . . . . . . . . . . . . . . . . . . . . . 70 Placard, Tire and Loading Information . . . . . . . . . 221 Power Distribution Center . . . . . . . . . . . . . . . . . . . . . 303 Door Locks . .
INDEX 361 Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280 Remote Keyless Entry . . . . . . . . . . . . . . . . . . . . . 22 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . . . . 306 Replacement Keys . . . . . . . . . . . . . . . . . . . . . . . . 16 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 268 Replacement Tires . . . . . . . . . . . . . . . . . . . . . . . 231 Reporting Safety Defects . . . . . . . . . . . . . . . . . . . 345 Restraints, Child . . .
INDEX Security Alarm (Theft Alarm) . . . . . . . . . . . . . . . . 26 Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . . . 14,27 Sentry Key Programming . . . . . . . . . . . . . . . . . . . 16 Service and Maintenance . . . . . . . . . . . . . . . . . . 316 Service Assistance . . . . . . . . . . . . . . . . . . . . . . . 340 Service Contract . . . . . . . . . . . . . . . . . . . . . . . . . 342 Service Manuals . . . . . . . . . . . . . . . . . . . . . . . . 346 Setting the Clock . . . . . .
INDEX 363 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 Temperature Gauge, Engine Coolant . . . . . . . 138,247 Tether Anchor, Child Restraint . . . . . . . . . . . . . . . 57 Theft Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Theft System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . . 100 Tire and Loading Information Placard . . . . . . 220,221 Tire Identification Number (TIN) . . . . .
INDEX Minimum Requirements . . . . . . . . . . . . . . . . . 242 Trailer and Tongue Weight . . . . . . . . . . . . . . . . 242 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241 Transaxle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 Automatic . . . . . . . . . . . . . . . . . . . . 12,196,199,293 Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204 Manual . . . . . . . . . . . . . . . . . . . . . . . . 13,196,205 Operation . . . . . . . . . . . . . .
INDEX 365 Warning, Door Ajar . . . . . . . . . . . . . . . . . . . . . . 141 Warning Lights (Instrument Cluster Description) . 137 Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . 6 Warranty Information . . . . . . . . . . . . . . . . . . . . . 343 Washer, Adding Fluid . . . . . . . . . . . . . . . . . . . . . 192 Washer, Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 Washers, Windshield . . . . . . . . . . . . . . . . . . . . . . 99 Washing Vehicle . . . . . . . . . . . . .
NOTES
NOTES
NOTES