2009 GRAND CHEROKEE GRAND CHEROKEE 2009 owner’s manual Chrysler LLC 81-326-0954 150920 GrCherokee.indd 1 Second Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 8 䡵 Rollover Warning . . . . . . . . . . . . . . . . . . . . . . . 5 䡵 Vehicle Identification Number 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 6 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . . 9 ..............
4 INTRODUCTION INTRODUCTION This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive enclosed vehicles were not intended. It handles and maneuvers differently from many passenger cars both on-road and off-road, so take time to become familiar with your vehicle. The two-wheel drive utility vehicle was designed for on-road use only.
INTRODUCTION 5 NOTE: After you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold so that the new owner will be aware of all safety warnings. When it comes to service, remember that your authorized dealer knows your vehicle best, has the factory-trained technicians and genuine MOPAR威 parts, and is interested in your satisfaction. ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles.
6 INTRODUCTION Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the U.S. government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year and could reduce disabling injuries by two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up.
INTRODUCTION 7 1
8 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 9 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 14 䡵 Vehicle Security Alarm . . . . . . . . . . . . . . . . . . . 20 ▫ Wireless Ignition Node (WIN) . . . . . . . . . . . . 14 ▫ Rearming The System . . . . . . . . . . . . . . . . . . 20 ▫ Integrated Ignition Key . . . . . . . . . . . . . . . . . 15 ▫ To Set The Alarm . . . . . . . . . . . . . . . . . . . . . 20 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Express Down Window Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 25 ▫ Programming Additional Transmitters . . . . . . 25 ▫ Transmitter Battery Service . . . . . . . . . . . . . . 25 ▫ General Information . . . . . . . . . . . . . . . . . . . 26 䡵 Remote Starting System — If Equipped . . . . . . . 27 ▫ How To Use Remote Start . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 ▫ Seat Belts And Pregnant Women . . . . . . . . . . 45 ▫ Transporting Passengers . . . . . . . . . . . . . . . . 69 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . 45 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . 69 ▫ Driver And Front Passenger Supplemental Restraint Systems (SRS) . . . . . . . . . . . . . . . . . 46 ▫ Safety Checks You Should Make Inside The Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Remote Keyless Entry (RKE) transmitter with integrated ignition key and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the double-sided key into the ignition switch with either side up. Wireless Ignition Node (WIN) The Wireless Ignition Node (WIN) operates similar to an ignition switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Integrated Ignition Key The integrated ignition key operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and a valet key, which stores in the rear of the RKE transmitter. 2 The valet key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead. The valet key is also for locking the glove box. You can keep the valet key with you when valet parking.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • If you try to remove the key before you place the shift lever in PARK, it may become trapped temporarily in the ignition switch. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition switch to warn you that this safety feature is inoperable. The engine can be started and stopped, but the key cannot be removed until you obtain service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Key-In-Ignition Reminder If you open the driver’s door with the integrated ignition key in the ignition, a chime will sound to remind you to remove the key. NOTE: The Key-In-Ignition reminder only sounds when the integrated ignition key is placed in the LOCK or ACC position. SENTRY KEY姞 The Sentry Key威 Immobilizer system prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • The Sentry Key威 Immobilizer system is not compatible with aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. • Exxon/Mobil Speedpass™, additional RKE transmitters, or any other transponder-equipped components on the same key chain will not cause a fault unless the additional part is physically held against the RKE transmitter being used to start the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: When having the Sentry Key威 Immobilizer system serviced, bring all vehicle RKE transmitters with you to the authorized dealer. Customer Key Programming If you have two valid RKE transmitters with integrated keys, you can program new transmitters to the system by performing the following procedure: 1.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information The Sentry Key威 system complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received, including interference that may cause undesired operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Vehicle Security Alarm is arming. During this 16 second arming period, opening any door or the liftgate will cancel the arming. If the Vehicle Security Alarm successfully arms, the Vehicle Security Light will flash at a slower rate to indicate the alarm is set. To Disarm the System To disarm the Vehicle Security Alarm, you will need to press the UNLOCK button on the RKE transmitter or turn the ignition key to the ON position.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Keyless Entry (RKE) transmitter. The RKE transmitter does not need not be pointed at the vehicle to activate the system. NOTE: Inserting the RKE transmitter into the ignition switch disables all buttons on that RKE transmitter; however, the buttons on the remaining RKE transmitters will continue to work. Driving the vehicle over 5 mph disables all RKE transmitter buttons, for all RKE transmitters, until the ignition is turned back to OFF/LOCK.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Remote Key Unlock, Driver Door/All Doors First Press This feature lets you program the system to unlock either the driver’s door, or all doors, on the first press of the UNLOCK button on the RKE transmitter.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Lock the Doors Press and release the LOCK button on the RKE transmitter to lock all doors. The turn signal lights will flash and the horn will chirp to acknowledge the signal. Sound Horn with Remote Key Lock This feature will cause the horn to chirp when the doors are locked with the RKE transmitter. This feature can be turned on or off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Using the Panic Alarm To turn the Panic Alarm feature on or off, press and hold the PANIC button on the RKE transmitter for at least one second and release. When the Panic Alarm is on, the headlights and park lights will flash, the horn will pulse on and off, and the interior lights will turn on.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Battery access is through a door located on the rear of the fob. Insert a small, flat blade screwdriver into the slot and gently pry open the access door. 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. Reposition the access door panel over the battery opening and snap into place.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 If your Remote Keyless Entry (RKE) transmitter fails to operate from a normal distance, check for these two conditions. 1. A weak battery in the RKE transmitter. The expected life of the battery is a minimum of three years. • Doors closed • Hood closed • Liftgate closed • Hazard switch off 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • If an engine fault is present the vehicle will start and then shut down 10 seconds later. • The park lamps will turn on and remain on during Remote Start mode. • For security, power window and power sunroof operation (if equipped) are disabled when the vehicle is in the Remote Start mode. • The engine can be started two consecutive times (two 15 minute cycles) with the RKE transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 DOOR LOCKS Manual Door Locks Use the manual door lock plunger to lock the doors from inside the vehicle. If the plunger is down when the door is closed, the door will lock. Therefore, make sure the key is not inside the vehicle before closing the door. Power Door Locks The power door lock switch is located on each front door panel. Press the switch to lock or unlock the doors.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you press the door lock switch while the keys are in the ignition switch, and the driver’s door is open, the doors will not lock. The rear doors cannot be opened from inside the vehicle until you pull up the lock plungers. Automatic Unlock On Exit Feature — If Equipped If Auto Unlock is enabled, this feature will unlock all the doors when the driver’s door is opened if the vehicle is stopped and in PARK or NEUTRAL.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the ON or ACCESSORY position. Child Protection Door Lock WINDOWS Power Windows The power window controls are located on the driver’s door trim panel.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Down Both the driver and front passenger window switch has an “Auto Down” feature. Press the window switch past the first detent, release, and the window will go down automatically. To cancel the “Auto Down” movement, operate the switch in either the up or down direction and release the switch. To open the window part way, press to the first detent and release it when you want the window to stop.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Resetting the Auto Up Feature Should the Auto Up feature stop working, the window probably needs to be reset. To reset Auto Up: 2 Pull the window switch up and close the window completely, then pull and hold the switch for one second. Window Lockout Switch The window lockout switch on the driver’s door allows you to disable the window controls on the other doors. To disable the window controls on the other doors, press the window lockout button.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting. LIFTGATE To open the liftgate, pull up (squeeze) on the handle and lift. Manually unlocking the vehicle doors with the plunger or a key in the lock cylinder will not unlock the liftgate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Liftgate Flipper Glass The liftgate flipper glass is also unlocked when the liftgate is unlocked. To open the flipper glass, push up on the window switch located on the liftgate. WARNING! To avoid injury, stand back when opening. Glass may automatically rise. Once the liftgate flipper glass has been opened, connection to the rear window wiper is interrupted, preventing activation of the rear wiper blade while the flipper glass is open.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Driving with the flipper glass open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flipper glass closed when you are operating the vehicle. OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! (Continued) • Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision which includes you. This can happen far away from home or on your own street. • Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Two people should never be belted into a single seat belt. People belted together can crash into one another in an accident, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size. Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of your seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A belt that is worn under your arm is very dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.). Removing Slack from Belt 6.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Locking Mode — If Equipped In this mode, the shoulder belt is automatically prelocked. The belt will still retract to remove any slack in the shoulder belt. When to Use the Automatic Locking Mode Use Automatic Locking mode anytime a child safety seat is installed in the rear center seating position. Children 12 years old and younger should be properly restrained in the rear seat whenever possible.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 How to Disengage the Automatic Locking Mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the Automatic Locking mode and activate the Vehicle Sensitive (Emergency) Locking mode. Energy Management Feature This vehicle has a safety belt system with an Energy Management feature in the front seating positions to help further reduce the risk of injury in the event of a head-on collision.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt must still be worn snugly and positioned properly. The pretensioners are triggered by the Occupant Restraint Control (ORC). Like the front airbags, the pretensioners are a single use item. After a collision that is severe enough to deploy the airbags and pretensioners, they must be replaced.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled. 4. Turn the ignition key to the OFF position. A single chime will sound to signify that you have successfully completed the programming. BeltAlert威 can be reactivated by repeating this procedure.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed. Driver and Front Passenger Supplemental Restraint Systems (SRS) This vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 The front airbags have a multistage inflator design. This may allow the airbags to have different rates of inflation that are based on collision severity and occupant size. 2 This vehicle is equipped with window bags to protect the driver, and front and rear passengers sitting next to a window. They are located above the side windows. Their covers are also labeled SRS/AIRBAG.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. • Do not stack luggage or other cargo up high enough to block the location of the window bag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Window bags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions. The window bag on the crash side of the vehicle is triggered in moderate to severe side collisions.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should use their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4. Do not lean against the door or window, airbags will inflate forcefully into the space between you and the door. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Airbag System Components The airbag system consists of the following: • Occupant Restraint Control (ORC) • Airbag Warning Light • Driver Airbag • Passenger Airbag • Side Curtain Airbags above Side Windows • Side Remote Acceleration Sensors • Driver Side Seat Track Position Sensor • Steering Wheel and Column • Instrument Panel • Interconnecting Wiring • Knee Impact Bolsters • Front Acceleration Sensors • Driver and Front Passenger Seat Belt Pretensioners How t
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The ORC also turns on the Airbag Warning Light for 2.5 to 8 seconds for a self-check when the ignition is first turned on. After the self-check, the Airbag Warning Light will turn off. If the ORC detects a malfunction in any part of the system, it turns on the Airbag Warning Light either momentarily or continuously. A single chime will sound if the light comes on again after initial start up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 • The Side Impact SRS Side Curtain Airbags are designed to activate only in certain side or rollover collisions. When the Occupant Restraint Control (ORC) detects a collision requiring the window bags to inflate, it signals the inflators on the crash side of the vehicle, and both sides of the vehicle when rollover is sensed. A quantity of nontoxic gas is generated to inflate the window bag.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor. They are not caused by contact with chemicals. They are not permanent and normally heal quickly. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the airbags deflate you may see some smoke-like particles.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 NOTE: The interior lights can only be deactivated if the key is removed from the ignition switch or the vehicle is driven. Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light You will want to have the airbag system ready to inflate for your protection in an impact. The airbag system is designed to be maintenance free.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 • Under certain circumstances, EDR data may not be recorded (e.g., loss of battery power). In conjunction with other data gathered during a complete accident investigation, the electronic data may be used by Chrysler LLC and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle performance.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Otherwise required by law. • Transmission gear selection Data parameters that may be recorded: • Cruise control status • Diagnostic trouble code(s) and warning lamp status for electronically-controlled safety systems, including the airbag system • Traction/stability control status • Airbag disable lamp status (if equipped) Child Restraints Everyone in your vehicle needs to be buckled up all the time — babies and children, too.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 enough for an adult safety belt. Always check the child seat Owner’s Manual to ensure you have the right seat for your child. Use the restraint that is correct for your child. WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with the front passenger airbag unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position. • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip. If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt (the cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary).
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For additional information refer www.seatcheck.org or call 1-866-SEATCHECK. to Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg), and who are older than one year, can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction, are for children who weigh 20 to 40 lbs (9 to 18 kg), and who are older than one year.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 LATCH — Child Seat Anchorage System (Lower Anchors and Tether for CHildren) Your vehicle’s rear seat is equipped with the child restraint anchorage system called LATCH. The LATCH system provides for the installation of the child restraint without using the vehicle’s seat belts, instead securing the child restraint using lower anchorages and upper tether straps from the child restraint to the vehicle structure.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you are installing LATCH-compatible child restraints in adjacent rear seating positions, you can use the LATCH anchors or the vehicle’s seat belt for the outboard position, but you must use the vehicle’s seat belt at the center position. If your child restraints are not LATCHcompatible, you can only install the child restraints using the vehicle’s seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 In addition, there are tether strap anchorages behind each rear seating position located on the back of the seat. Tether Strap Mounting Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. 2 To attach a child restraint tether strap: Route the tether strap over the seatback and attach the hook to the tether anchor located on the back of the seat.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty. SAFETY TIPS Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. WARNING! (Continued) • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Airbag Warning Light The light should come on and remain on for six to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Defroster Check operation by selecting the defrost mode and place the blower control on high speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 ▫ Illuminated Vanity Mirrors — If Equipped . . . 81 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 78 ▫ Sun Visor Extension — If Equipped . . . . . . . . 81 ▫ Automatic Dimming Mirror — If Equipped . . . 78 䡵 uconnect威 phone — If Equipped . . . . . . . . . . . . 82 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . 79 ▫ Operation . . . . . . . . . . .
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ General Information . . . . . . . . . . . . . . . . . . 110 ▫ Front Heated Seats — If Equipped . . . . . . . . 118 䡵 Voice Recognition System (VR) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 110 ▫ Rear Heated Seats — If Equipped . . . . . . . . . 120 ▫ Voice Recognition System (VR) Operation . . . 110 ▫ Commands . . . . . . . . . . . . . . . . . . . . . . . . 112 ▫ Voice Training . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 ▫ Headlights And Parking Lights . . . . . . . . . . 130 ▫ Headlight Time Delay . . . . . . . . . . . . . . . . . 137 ▫ Automatic Headlight System — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 131 ▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . 137 ▫ SmartBeams — If Equipped . . . . . . . . . . . . . 132 ▫ Daytime Running Lights — If Equipped . . . . 133 ▫ Automatic Headlight Leveling — HID Headlights Only . . . . . . . . . . .
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . 146 䡵 Overhead Console . . . . . . . . . . . . . . . . . . . . . 153 ▫ To Vary The Speed Setting . . . . . . . . . . . . . . 146 ▫ Courtesy/Reading Lights . . . . . . . . . . . . . . 153 ▫ To Accelerate For Passing . . . . . . . . . . . . . . 147 ▫ Sunglasses Storage . . . . . . . . . . . . . . . . . . . 154 䡵 Rear Park Assist — If Equipped . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 ▫ Opening Sunroof — Express . . . . . . . . . . . . 161 䡵 Power Inverter — If Equipped . . . . . . . . . . . . 165 ▫ Closing Sunroof — Express . . . . . . . . . . . . . 161 䡵 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . 167 ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . 161 䡵 Cargo Area Features . . . . . . . . . . . . . . . . . . . 167 ▫ Pinch Protect Override . . . . . . . . . . . . . . . . 162 ▫ Cargo Light . . . . . . . .
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted to center on the view through the rear window. Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Outside Mirrors To receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. WARNING! Automatic Dimming Mirror CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors Folding Feature All outside mirrors are hinged and may be moved either forward or rearward to resist damage. The hinges have three detent positions: full forward, full rearward and normal. After selecting a mirror, move the knob in the same direction you want the mirror to move. Use the center off position to guard against accidentally moving a mirror position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Power mirror preselected positions can be controlled by the optional Memory Seat Feature. Refer to “Driver Memory Seat” in this Section for further information. Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “Rear Window Features” in this Section for further information.
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE uconnect姞 phone — IF EQUIPPED NOTE: The sales code RER and REU radios contain an integrated uconnect威 phone. Refer to your “Navigation User’s Manual” for uconnect威 phone operating instructions for these radios. Radio sales code can be located on the lower right corner of the Radio faceplate. uconnect威 phone is a voice-activated, hands-free, invehicle communications system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 The uconnect威 phone is driven through your Bluetooth威 “Hands-Free Profile” cellular phone. uconnect威 features Bluetooth威 technology - the global standard that enables different electronic devices to connect to each other without wires or a docking station, so uconnect威 phone works no matter where you stow your cellular phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s uconnect威 phone.
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the uconnect威 phone such as ⬙CELL⬙ or caller ID on certain radios. Operation Voice commands can be used to operate the uconnect威 phone and to navigate through the uconnect威 phone menu structure. Voice commands are required after most uconnect威 phone prompts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say ⬙Help⬙ following the beep. The uconnect威 phone will play all the options at any prompt if you ask for help. To activate the uconnect威 phone from idle, simply press the PHONE button and follow the audible prompts for directions. All uconnect威 phone sessions begin with a press of the PHONE button on the radio control head.
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For identification purposes, you will be prompted to give the uconnect威 phone a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between one and seven, with one being the highest priority. You can pair up to seven cellular phones to your uconnect威 phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 • The system will prompt you to say the name of the person you want to call. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook New Entry.⬙ • After the ⬙Ready⬙ prompt and the following beep, say the name of the person you want to call. For example, you can say ⬙John Doe,⬙ where John Doe is a previously stored name entry in the uconnect威 phonebook or downloaded phonebook.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The uconnect威 phone will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language. In addition, if equipped and supported by your phone, uconnect威 phone automatically downloads your cellular phone’s phonebook.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 • This downloaded phonebook cannot be edited or deleted on the uconnect威 phone. These can only be edited on the cellular phone. The changes are transferred and updated to uconnect威 phone on the next phone connection. Phonebook Download — Single Entry If equipped and supported by your phone, uconnect威 phone allows the user to download entries from their phone via Bluetooth威. To use this feature, press the PHONE button and say “Phonebook Download.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Edit uconnect威 Phonebook Entries NOTE: • Editing names in the phonebook is recommended when the vehicle is not in motion. • Automatic downloaded phonebook entries cannot be deleted or edited. • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Edit.⬙ • You will then be asked for the name of the phonebook entry that you wish to edit.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete or you can say ⬙List Names⬙ to hear a list of the entries in the phonebook from which you choose. To select one of the entries from the list, press the VOICE RECOGNITION button while the uconnect威 phone is playing the desired entry and say ⬙Delete.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook List Names.⬙ • The uconnect威 phone will play the names of all the phonebook entries, including the downloaded phonebook entries, if available. • To call one of the names in the list, press the VOICE RECOGNITION button during the playing of the desired name, and say ⬙Call.⬙ NOTE: The user can also exercise ⬙Edit⬙ or ⬙Delete⬙ operations at this point.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 cellular phone. Press the PHONE button to place the current call on hold and answer the incoming call. NOTE: The uconnect威 phone compatible phones in the market today do not support rejecting an incoming call when another call is in progress. Therefore, the user can only answer an incoming call or ignore it.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Three-Way Calling To initiate three-way calling, press the VOICE RECOGNITION button while a call is in progress, and make a second phone call, as described under ⬙Making a Second Call While Current Call is in Progress.⬙ After the second call has established, press and hold the PHONE button until you hear a double beep, indicating that the two calls have been joined into one conference call.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 • After the ignition key is switched to OFF, a call can continue on the uconnect威 phone for a certain duration, after which the call is automatically transferred from the uconnect威 phone to the cellular phone. • An active call is automatically transferred to the cellular phone after the ignition key is switched to OFF. • Continue to follow the system prompts to complete the language selection.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the phone is not reachable and the uconnect威 phone is operational, you may reach the emergency number as follows: • If supported, this number may be programmable on some systems. To do this, press the PHONE button and say ‘Setup’, followed by ‘Emergency’. • Press the PHONE button to begin. • The uconnect威 phone does slightly lower your chances of successfully making a phone call as to that for the cell phone directly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Towing Assistance If you need towing assistance: • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Towing Assistance.⬙ NOTE: • The towing assistance number dialed is based on the country where the vehicle is purchased (1-800-5282069 for the U.S., 1-877-213-4525 for Canada, 55-143454 for Mexico City and 1-800-712-3040 for outside Mexico City in Mexico). • If supported, this number may be programmable on some systems.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When calling a number with your uconnect威 phone that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can press the VOICE RECOGNITION button and say the sequence you wish to enter, followed by the word ⬙Send.⬙ For example, if required to enter your PIN followed with a pound, (3 7 4 6 #), you can press the VOICE RECOGNITION button and say, ⬙3 7 4 6 # Send.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Turning Confirmation Prompts ON/OFF Turning confirmation prompts off will stop the system from confirming your choices (e.g., the uconnect威 phone will not repeat a phone number before you dial it). • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Confirmations.⬙ The uconnect威 phone will play the current confirmation prompt status and you will be given the choice to change it.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mute/Un-Mute (Mute OFF) When you mute the uconnect威 phone, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the uconnect威 phone: • Press the VOICE RECOGNITION button. • Following the beep, say ⬙Mute.⬙ In order to un-mute the uconnect威 phone: • Press the VOICE RECOGNITION button. • Following the beep, say ⬙Mute off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 • The uconnect威 phone will play the phone names of all paired cellular phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the VOICE RECOGNITION button and say “Select” or “Delete.” Also, see the next two sections for an alternate way to “select” or “delete” a paired phone.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Things You Should Know About Your uconnect姞 phone uconnect威 phone Tutorial To hear a brief tutorial of the system features, press the PHONE button and say “uconnect威 Tutorial.” Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers, the uconnect威 phone Voice Training feature may be used. To enter this training mode, follow one of the two following procedures: From outside the uconnect威 phone mode (e.g.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 • Speak normally, without pausing, just as you would speak to a person sitting a few feet/meters away from you. • When navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say ⬙Send.⬙ • Make sure that no one other than you is speaking during a voice recognition period. • Storing names in the phonebook when the vehicle is not in motion is recommended.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In a convertible vehicle, system performance may be compromised with the convertible top down. • Echo at the far end can sometimes be reduced by lowering the in-vehicle audio volume. Far End Audio Performance • In a convertible vehicle, system performance may be compromised with the convertible top down.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 3
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 3
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call uconnect威 Tutorial try again voice training work yes 3
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 When you press the VR button, you will hear a beep. The beep is your signal to give a command. NOTE: If you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the VR button, listen for the beep, and say your command. Pressing the VR button while the system is speaking is known as “barging in.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Commands The Voice Recognition system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the Volume 1. Start a dialogue by pressing the VR button. 2. Say a command (e.g., “Help”). 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the Voice Recognition system is speaking.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Radio FM To switch to the FM band say “FM” or “Radio FM”.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memo To switch to the voice recorder mode say “Memo”. In this mode, you may say the following commands: • “New Memo” (to record a new memo) — During the recording you may press the VR button to stop recording. You proceed by saying one of the following commands: − “Previous” (to play the previous memo) − “Delete” (to delete a memo) • “Delete All” (to delete all memos) System Setup To switch to system setup say “Setup”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 NOTE: Keep in mind that you have to press the VR button first and wait for the beep before speaking the “Barge In” commands. Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers, uconnect威 phone Voice Training feature may be used. 1. Press the VR button, say “System Setup” and once you are in that menu then say “Voice Training.” This will train your own voice to the system and will improve recognition. 2.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Seat Adjustment — Recline To adjust the seatback, lift the lever located on the outboard side of the seat, lean back, and release the lever at the desired position. To return the seatback, lift the lever, lean forward, and release the lever. WARNING! • Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision, you could slide under the seat belt and be seriously or even fatally injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 3 Manual Lumbar Control Power Seat Switches Eight-Way Driver’s Power Seat The driver’s power seat switches are located on the outboard side of the driver’s seat lower side trim. The bottom switch controls up/down, forward/rearward, and tilt adjustment. The top switch controls the seatback recline adjustment.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The four-way seat does not have an up/down adjustment. Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjustable head restraints should be adjusted so that the upper edge is as High as practical. The head restraints have a locking button which must be pushed in to lower the head restraint to all positions. The restraints may be raised without pushing in the button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 After turning the ignition ON, you can choose from a High or Low heat setting. Illuminated LEDs on each switch indicate the level of heat in use. two to one, indicating the change. The Low-level setting will turn Off automatically after approximately 30 minutes. Press the switch once to select High-level heating. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. To avoid heated seat surfaces coming in contact with each other and potential seat overheating, ALWAYS ensure that the seat heater is in the Off position (amber lights indicate High/Low/Off) before placing any of the seats into a folded flat position (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 When the High-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the normal High-level. If the High-level setting is selected, the system will automatically switch to Low-level after approximately 30 minutes of continuous operation. At that time, the number of illuminated LEDs changes from two to one, indicating the change.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 60/40 Split Rear Seat To Lower Rear Seat Either side of the rear seat can be lowered to allow for extended cargo space and still maintain some rear seating room. NOTE: Be sure that the front seats are fully upright and positioned forward. This will allow the rear seatback to fold down easily. 1. Pull the release strap (toward the front of the vehicle) to release. Rear Seat Release NOTE: Do not fold the rear seat down with the center seat belt buckled. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 WARNING! The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion. They could be seriously injured in an accident. Children should be seated and using the proper restraint system. Folding Rear Seat To Raise Rear Seat Raise the rear seatback and lock it into place.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage (Rear Seat Armrest) — If Equipped The rear seat may be equipped with a center storage armrest. Armrest Storage Latch Rear Seat Armrest Press the latch and lift the top of the armrest to access the storage bin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Keyless Entry (RKE) transmitters can also be programmed to recall the same positions when the UNLOCK button is pressed. position. The memory system can accommodate up to four RKE transmitters, each one linked to either of the two memory positions.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Adjust the brake and accelerator pedals to the desired positions. 5. Turn on the radio and set the radio station presets (up to 12 AM and 12 FM stations can be set). 6. Turn the ignition switch to the LOCK position and remove the key. 7. Press and release the S (SET) button located on the driver’s door. 8. Within five seconds, press and release memory button 1 or 2 on the driver’s door.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 To recall the memory setting for driver two, press memory button number 2 on the driver’s door, or the UNLOCK button on the RKE transmitter linked to memory position 2. A recall can be cancelled by pressing any of the memory buttons on the drivers door during a recall (S, 1, or 2). When a recall is cancelled, the driver’s seat, driver’s mirror, and the pedals stop moving. A delay of one second will occur before another recall can be selected.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Easy Entry/Exit Seat This feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle. There are two possible Easy Entry/Exit adjustments available: • The seat cushion will move rearward approximately 2.5 in (60 mm), if the starting position of the seat is greater than or equal to 2.67 in (68 mm) forward of the rear seat stop when the key is removed from the ignition switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. 1. Pull the release lever located below the instrument panel and in front of the driver’s door. 3 Safety Latch Location CAUTION! Hood Release 2. Reach under the hood, move safety latch to the left, and lift the hood. To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving. Headlights and Parking Lights Turn the end of the multifunction lever to the first detent for parking light operation. Turn to the second detent for headlight operation. Turn to the third detent for AUTO headlight operation (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Automatic Headlight System — If Equipped Turn the end of the multifunction lever to the third detent to activate the automatic headlight system. This system performs two functions. With the engine running and the multifunction lever in the AUTO position, the headlights will turn on and off based on the surrounding light levels.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SmartBeams — If Equipped The SmartBeam system provides increased forward lighting at night by automating high beam control through the use of a digital camera mounted on the inside rearview mirror. This camera detects vehicle specific light and automatically switches from high beams to low beams until the approaching vehicle is out of view.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 To Deactivate 1. Pull back on the multifunction lever to manually deactivate the system (normal operation of low beams). 2. Push back on the multifunction lever once again to reactivate the system. NOTE: Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions (sticker, toll box, etc.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Instrument Panel and Interior Lights When the multifunction lever is in the parking light, headlight, or AUTO position (if equipped), rotating the center portion of the lever up and down will increase and decrease the brightness (dimmer control) of the instrument panel lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Battery Saver Feature If the multifunction lever is left in the interior light position, parking light position, or the headlight position when the ignition switch is moved to the LOCK position, the battery saver feature will automatically turn off the exterior and interior lights after eight minutes. Normal operation will resume when the ignition is turned ON or when the headlight switch is turned to another position.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • Turning on the high beam headlights turns off the fog lights. • A front fog light is a lighting device that provides illumination in front of the vehicle under conditions of fog, rain, snow, or dust. The front fog lights supplement the lower beam of a standard headlight system. • Proper aim and adjustment of the front fog lights should be made to prevent excessive glare for other drivers.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 High Beam Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever towards you to switch the headlights back to low beam. Flash-to-Pass You can signal another vehicle by lightly pulling the multifunction lever toward the steering wheel. This will cause the high beam headlights to turn on, and remain on until the lever is released.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE contains both driver and passenger reading lights), reading lights (located above the rear doors), and a rear cargo light. Opening a door, pressing the UNLOCK button on the Remote Keyless Entry (RKE) transmitter or turning the center of the multifunction control lever to the extreme up position, will activate all interior courtesy lights. Front Map/Reading Lights These lights are mounted in the overhead console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 WINDSHIELD WIPERS AND WASHERS The front and rear wipers and washers are operated by a switch in the right side control lever. Turn the end of the control lever to select Low, High, or one of the five speed sensitive intermittent windshield wiper speeds. Refer to “Speed Sensitive Intermittent Wiper System” in this section. For information on the rear wiper and washer, refer to “Rear Window Features” in this section.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for several seconds after the lever is released, and then resume the intermittent interval previously selected. If the lever is pulled while in the off position, the wipers will operate for several wipe cycles, then turn off. WARNING! Sudden loss of visibility through the windshield could lead to an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Rain Sensing Wipers — If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead. Rotate the end of the multifunction lever to one of five settings to activate this feature. The sensitivity of the system can be adjusted with the multifunction lever.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE operate until the wiper switch is moved, vehicle speed is greater than 0 mph (0 km/h), or the outside temperature is greater than 32°F (0°C). • Transmission in NEUTRAL Position — When the ignition is ON, and the transmission is in the NEUTRAL position, the rain sensing system will not operate until the wiper switch is moved, vehicle speed is greater than 5 mph (8 km/h), or the shift lever is moved out of the NEUTRAL position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 the steering wheel outward or push it inward as desired. To lock the steering column in position, push the control handle upward until fully engaged. adjusted without compromising safety or comfort in actuating the pedals. WARNING! 3 Do not adjust the steering wheel while driving. The telescoping adjustment must be locked while driving.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the top of the switch to move the pedals rearward (toward the driver). • The pedals can be adjusted with the ignition OFF. • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in REVERSE (R) or when the Electronic Speed Control is ON.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it. To Set At A Desired Speed When the vehicle has reached the desired speed, press down on the lever and release. Release the accelerator and the vehicle will operate at the selected speed.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Speed Control without erasing the set speed memory. Pressing the ON/OFF button or turning the ignition switch OFF erases the set speed memory. that tapping the lever three times will increase speed by 3 mph (5 km/h) (3.7L, 4.7L, 5.7L, and 3.0L diesel engines). To Resume Speed To resume a previously set speed, push the RESUME ACCEL lever up and release. Resume can be used at any speed above 20 mph (32 km/h) for 3.7L, 4.7L, and 5.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 To Accelerate For Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control On Hills The transmission may downshift on hills to maintain the vehicle set speed. NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on moderate hills is normal.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The sensors can detect obstacles from approximately 12 to 59 in (30 to 150 cm) from the rear fascia in the horizontal direction, depending on the location and orientation of the obstacle and the type of obstacle. Rear Park Assist Warning Display The Rear Park Assist Warning Display, located in the headliner near the flipper glass, provides both visible and audible warnings to indicate the distance between the rear fascia and the detected obstacle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 The system dimly illuminates the two outer most yellow LEDs when it is ON and detecting no obstacles. The following chart shows the warning display operation when the system is detecting an obstacle: WARNING DISPLAY DISTANCES DISPLAY LED 1st LED 2nd LED 3rd LED 4th LED 5th LED 6th LED 7th LED 8th LED OBSTACLE DISTANCE FROM: REAR CORNERS REAR CENTER 59 in (150 cm) 51 in (130 cm) 45 in (115 cm) 31.5 in (80 cm) 39 in (100 cm) 25.5 in (65 cm) 33.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Enable/Disable The Rear Park Assist The Rear Park Assist can be enabled and disabled with a switch located on the upper switch bank of the instrument panel. When the switch is pressed to disable the system, the instrument cluster will display the “PARK ASSIST DISABLED” message. Refer to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Cleaning The Rear Park Assist Clean the Rear Park Assist Sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could damage the sensors.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • To avoid vehicle damage, the vehicle must be driven slowly when using the Rear Camera system to be able to stop in time when an obstacle is seen. It is recommended that the driver look frequently over his/her shoulder when using the Rear Camera system. 4. Enable or disable the rear camera feature by selecting ⬙enable rear camera in reverse⬙ soft key. 5. Press the “save” soft key. 6.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 4. When the vehicle is shifted into REVERSE, an image of the rear of the vehicle will appear with a caution note to ⬙check entire surroundings⬙ displayed across the top of the screen. After five seconds this note will disappear. 5. When the vehicle is shifted out of REVERSE, the rear camera mode is exited and the audio screen appears again.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The lights also turn on when a front door or rear door is opened. The lights will also turn on when the UNLOCK button on the remote keyless entry transmitter is pressed. The HomeLink威 buttons are located in the overhead console, and contain one, two, or three dots/lines designating the different HomeLink威 channels. Sunglasses Storage At the rear of the console a compartment is provided for the storage of a pair of sunglasses.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 WARNING! • Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) from the HomeLink威 buttons while keeping the EVIC display in view. NOTE: Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section. For optimal training, point the battery end of the handheld transmitter away from the HomeLink威. 4. Press and hold the just-trained HomeLink威 button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door). 6. Firmly press and release the “learn” or “training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Reprogramming A Single HomeLink姞 Button To reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink威 button for 20 seconds until the EVIC display states “CHANNEL # TRAINING.” Do not release the button. 3. Without releasing the button, proceed with Programming HomeLink威 Step 2 and follow all remaining steps.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. 1. This device may not cause harmful interference 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 WARNING! • Never leave children in a vehicle, with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing the sunroof, press the switch forward and hold for two seconds after the reversal occurs. This allows the sunroof to move towards the closed position. NOTE: Pinch protection is disabled while the switch is pressed. Venting Sunroof — Express Press and release the ⬙Vent⬙ button, and the sunroof will open to the vent position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Ignition Off Operation The power sunroof switches remain active for up to 10 minutes after the ignition switch has been turned OFF. Opening either front door will cancel this feature. Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed. 3 POWER OUTLETS Front Power Outlet To the left and right of the convenience tray (lower center of instrument panel) is an outlet for electric-powered accessories.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! To avoid serious injury or death: • Do not use a three-prong adapter. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 POWER INVERTER — IF EQUIPPED There is a 115-Volt, 150-Watt inverter outlet located on the back of the center console to convert DC current to AC current. Power Inverter This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts. Certain high-end video games, such as Playstation3 and XBox360 will exceed this power limit, as will most power tools.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the power inverter switch (located on the upper switch bank) to turn the power on to the outlet. Press the switch again to turn the power off. NOTE: • When the power inverter switch is pressed, there will be a delay of approximately one second before the inverter status indicator turns ON. The status indicator of the AC power inverter indicates whether the inverter is producing AC power.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 CUPHOLDERS In the center console, there are two cupholders for the front seat passengers. 3 Rear Cupholders CARGO AREA FEATURES Front Cupholders The rear passengers have access to two cupholders that pull out from the lower center of the rear seat. Cargo Light The cargo area light is activated by opening the liftgate, opening any door, or by rotating the dimmer control on the multifunction lever to the extreme top position.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the cargo light lens surface will turn off all interior lamps. Push on the lens surface a second time to restore the interior lights to normal operation. Rear Storage Compartment The rear storage compartment is located on the driver’s side behind the second row seat. Retractable Cargo Area Cover — If Equipped NOTE: The purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 WARNING! In an accident, a loose cargo cover in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do not store in the vehicle.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Tie-Down Hooks The tie-downs located on the cargo area floor should be used to safely secure loads when the vehicle is moving. Cargo Tie-Down Hooks WARNING! • To help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 WARNING! (Continued) • Do not carry loads which exceed the load limits described on the label attached to the left door or left door center pillar. • Always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible. • Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The cargo load floor is held by spring loaded latches. In order to use the cargo load floor, use the following procedure: NOTE: The cargo load floor latches should not be used as cargo tie-downs. 1. Flip up pull loop(s) so they are perpendicular (straight up) to the top surface of the tray. 2. Pull up on loop(s) and twist 90 degrees, so they are parallel to the slotted hole in tray. 3. Lift the tray over the loop(s), and reposition the tray. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 If the liftgate flipper glass is open, connection to the rear window wiper is interrupted preventing activation of the rear wiper blade. When the liftgate flipper glass is closed, the rear wiper switch, or the ignition switch, needs to be turned OFF and ON to restart the rear wiper.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • To avoid damaging the electrical conductors of the rear window defroster, do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • Labels can be peeled off after soaking with warm water. ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 NOTE: • To help control wind noise when the crossbars are not in use, place the front crossbar in the second detent from the front of the vehicle and the rear crossbar in the last detent closest to the rear of the vehicle. • If the rear crossbar (or any metallic object) is placed over the satellite radio antenna (if equipped), you may experience interruption of satellite radio reception.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) WARNING! • Travel at reduced speeds and turn corners carefully when carrying large or heavy loads on the roof rack. Wind forces, due to natural causes or nearby truck traffic, can add sudden upward lift to a load. This is especially true on large flat loads and may result in damage to the cargo or your vehicle. Cargo must be securely tied before driving your vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 181 ▫ Compass Display . . . . . . . . . . . . . . . . . . . . 200 䡵 Instrument Cluster – Gasoline Engine . . . . . . . 182 ▫ Personal Settings (Customer-Programmable Features) . . . . . . . . . . . . . . . . . . . . . . . . . . 202 䡵 Instrument Cluster – Diesel Engine . . . . . . . . . 183 䡵 Instrument Cluster Description . . . . . . . . . . . . 184 䡵 Electronic Vehicle Information Center (EVIC) . .
178 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Notes On Playing MP3/WMA Files . . . . . . . 218 ▫ List Button (Disc Mode For MP3/WMA Play) . . . . . . . . . 220 ▫ Info Button (Disc Mode For MP3/WMA Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 䡵 AM/FM/CD/DVD Radio (RER/REN) – If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 ▫ Operating Instructions — Voice Recognition System (VR) — If Equipped . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 179 䡵 Universal Consumer Interface (UCI) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247 ▫ Selecting uconnect威 studios (Satellite) Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253 ▫ Connecting The iPod威 . . . . . . . . . . . . . . . . . 248 ▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . 253 ▫ Using This Feature . . . . . . . . . . . . . . . . . . . 248 ▫ Reception Quality . . . . . . . . . . . . . . . . . .
180 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . 259 䡵 CD/DVD Maintenance . . . . . . . . . . . . . . . . . 260 䡵 Radio Operation And Cellular Phones . . . . . . . 260 䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . 261 ▫ Manual Air Conditioning And Heating System — If Equipped . . . . . . . . . . . . . . . . . 261 ▫ Automatic Temperature Control — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 264 ▫ Operating Tips . .
UNDERSTANDING YOUR INSTRUMENT PANEL 181 INSTRUMENT PANEL FEATURES 4 1 2 3 4 - Air Outlet - Instrument Cluster - Radio - Glove Compartment 5 6 7 8 - Upper Switch Bank Power Outlet/Cigar Lighter Storage Bin Power Outlet 9 - Lower Switch Bank 10 - Climate Controls 11 - Ignition Switch 12 - Storage Bin
182 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER – GASOLINE ENGINE
UNDERSTANDING YOUR INSTRUMENT PANEL 183 INSTRUMENT CLUSTER – DIESEL ENGINE 4
184 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Speedometer Indicates vehicle speed. 2. Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir.
UNDERSTANDING YOUR INSTRUMENT PANEL 185 WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately. Vehicles equipped with the Anti-Lock Brake System (ABS), are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light.
186 UNDERSTANDING YOUR INSTRUMENT PANEL the ON position before engine start. If the bulb does not come on when turning the key from OFF to ON, have the condition checked promptly. during starting, stays on, or turns on while driving, have the system inspected by an authorized dealer as soon as possible. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc. may illuminate the light after engine start.
UNDERSTANDING YOUR INSTRUMENT PANEL 187 8. Tachometer Indicates the engine speed in revolutions per minute (RPM). Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood. 9. Vehicle Security Light This light will flash rapidly for approximately 15 seconds when the vehicle theft alarm is arming. The light will flash at a slower speed continuously after the alarm is set.
188 UNDERSTANDING YOUR INSTRUMENT PANEL vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.
UNDERSTANDING YOUR INSTRUMENT PANEL 189 tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style.
190 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealership for service if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. 14.
UNDERSTANDING YOUR INSTRUMENT PANEL 191 17. 4WD LOW Indicator — If Equipped This light alerts the driver that the vehicle is in the 4WD LOW mode. The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed. 18. Seat Belt Reminder Light When the ignition switch is first turned ON, this light will turn on for five to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound.
192 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: You must apply the brakes before shifting from PARK. 22. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 23. Electronic Throttle Control (ETC) Warning Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a problem is detected the light will come on while the engine is running.
UNDERSTANDING YOUR INSTRUMENT PANEL 193 vehicle is experiencing a problem with the charging system. Obtain SERVICE IMMEDIATELY. See an authorized dealer. 26. Low Fuel Light This light will turn on, and a single chime will sound, when the fuel level drops to 1/8 tank. The Low Fuel Warning Light may turn on and off again, especially during and after hard braking, accelerations, or turns. This occurs due to the shifting of the fuel in the tank.
194 UNDERSTANDING YOUR INSTRUMENT PANEL • Vehicle Information Warning Message Displays • Personal Settings (Customer-Programmable Features) • Compass Display • Outside Temperature Display • Trip Computer Functions The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: MENU Button Press and release the MENU button and the mode displayed will change between Trip Functions, Personal Settings, and System Status.
UNDERSTANDING YOUR INSTRUMENT PANEL 195 Electronic Vehicle Information Center (EVIC) Displays When the appropriate conditions exist, the Electronic Vehicle Information Center (EVIC) displays the following messages: • PROGRAMMING ACTIVE — NEW KEY PROGRAMMED • TURN SIGNAL ON • LEFT/RIGHT REAR DOOR OPEN (with graphic) • PERFORM SERVICE • X DOORS OPEN (with graphic) • DAMAGED KEY — KEY DOES NOT COMMUNICATE • LIFTGATE OPEN (with graphic) • KEY NOT PROGRAMMED — KEY NOT PROGRAMMED • WRONG KEY — KEY DOES N
196 UNDERSTANDING YOUR INSTRUMENT PANEL • LIFTGATE/HOOD OPEN (with graphic) • AUTO HIGH BEAMS ON • HOOD/GLASS/DOOR OPEN (with graphic) • AUTO HIGH BEAMS OFF • HOOD/GLASS/DOORS OPEN (with graphic) • PARK ASSIST DISABLED • HOOD/GATE/DOOR OPEN (with graphic) • SERVICE SUSPENSION • HOOD/GATE/DOORS OPEN (with graphic) • SERVICE PARK ASSIST SYSTEM • LIFTGLASS/DOOR OPEN (with graphic) • TRANSMISSION OVER TEMP • LIFTGLASS/DOORS OPEN (with graphic) • CHECK SHIFT PROCEDURE • LIFTGLASS/HOOD OPEN (with g
UNDERSTANDING YOUR INSTRUMENT PANEL 197 • IOD FUSE OUT • HILL DESCENT CONTROL • MEMORY #1 POSITIONS SET • MEMORY #2 POSITIONS SET • MEMORY SYSTEM DISABLED — SEATBELT BUCKLED (with graphic) • MEMORY SYSTEM DISABLED — VEHICLE NOT IN PARK • LEFT FRONT LOW PRESSURE (Premium TPM System Only) • RIGHT FRONT LOW PRESSURE (Premium TPM System Only) • LEFT REAR LOW PRESSURE (Premium TPM System Only) • RIGHT REAR LOW PRESSURE (Premium TPM System Only) • DRIVER 1 MEMORY • SPARE LOW PRESSURE (Premium TPM System Only)
198 UNDERSTANDING YOUR INSTRUMENT PANEL • PRESS BRAKE TO START • INSERT KEY • TURN TO ON Engine Oil Change Indicator System Oil Change Required (Gasoline Engines Only) Your vehicle is equipped with an engine oil change indicator system. The “Oil Change Required” message will flash in the EVIC display for approximately 10 seconds after a single chime has sounded, to indicate the next scheduled oil change interval.
UNDERSTANDING YOUR INSTRUMENT PANEL 199 • Trip A • Trip B • Elapsed Time • Service Distance • Display Units of Measure In Press the SCROLL button to cycle through all the Trip Computer functions. The Trip Functions mode displays the following information: Average Fuel Economy Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read “RESET” or show dashes for two seconds.
200 UNDERSTANDING YOUR INSTRUMENT PANEL Trip A Shows the total distance traveled for Trip A since the last reset. Trip B Shows the total distance traveled for Trip B since the last reset. Elapsed Time Shows the total elapsed time of travel since the last reset when the ignition switch is in the ACC position. Elapsed time will increment when the ignition switch is in the ON or START position.
UNDERSTANDING YOUR INSTRUMENT PANEL 201 Manual Compass Calibration If the compass appears erratic and the “CAL” indicator does not appear in the EVIC display, you must put the compass into the Calibration Mode manually, as follows: 1. Turn on the ignition switch. 2. Press the MENU button until Personal Settings (Customer Programmable Features) menu is reached. 3. Press the SCROLL button until “Calibrate Compass” is displayed in the EVIC. 4.
202 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Press and release the FUNCTION SELECT button to change the variance number. Continue until desired number is reached. 5. Press either MENU, SCROLL, or COMPASS/TEMP button to set the value and exit. Personal Settings (Customer-Programmable Features) Personal Settings allows the driver to set and recall features when the transmission is in PARK. 1. Turn the ignition switch ON. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 203 FUNCTION SELECT button while in this display to select English, Espanol, or Francais. Then, as you continue, the information will display in the selected language. NOTE: The EVIC will not change the uconnect威 language selection. Please refer to “Language Selection” in the uconnect威 phone section of this manual for details. Auto Door Locks When YES (Y) is selected, all of the doors will lock automatically when the vehicle reaches a speed of 15 mph (24 km/h).
204 UNDERSTANDING YOUR INSTRUMENT PANEL feature may be selected with or without the “Flash Lamps with Lock” feature. To make your selection, press and release the FUNCTION SELECT button until YES (Y) or NO (N) appears. Flash Lamps with Lock When YES (Y) is selected, the front and rear turn signals will flash when the doors are locked or unlocked with the RKE transmitter. This feature may be selected with or without the “Sound Horn with Lock” feature.
UNDERSTANDING YOUR INSTRUMENT PANEL 205 NOTE: Turning the headlights on during the daytime causes the instrument panel lights to dim. To increase the brightness, refer to “Lights” in Section 3 of this manual. Rain Sensing Intermittent Wipers — If Equipped When YES (Y) is selected, the system will automatically activate the windshield wipers if it senses moisture on the windshield. To make your selection, press and release the FUNCTION SELECT button until YES (Y) or NO (N) appears.
206 UNDERSTANDING YOUR INSTRUMENT PANEL door. Refer to “Easy Entry/Exit Seat” under “Driver Memory Seat” in Section 3 of this manual for more information. Hill Start Assist To make your selection, press and release the FUNCTION SELECT button until YES (Y) or NO (N) appears.
UNDERSTANDING YOUR INSTRUMENT PANEL 207 • Tire Pressure Monitor System (shows the current pressure of all four road tires.) For additional information, refer to “Tire Pressure Monitor System” in Section 5 of this manual. NOTE: • Tires heat up during normal driving conditions. Heat will cause the tire pressure to increase from 2 to 6 psi (14 to 41 kPa) during normal driving conditions. Refer to “Tires-General Information/Tire Inflation Pressures” in Section 5 for additional information.
208 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second time to turn off the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. SCAN Button Pressing the SCAN button causes the tuner to search for the next listenable station in AM, FM or Satellite (if equipped) frequencies, pausing for five seconds at each listenable station before continuing to the next.
210 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save the time change. TUNE Control Turn the rotary TUNE/SCROLL control knob clockwise to increase or counterclockwise to decrease the frequency. 5. To exit, press any button/knob or wait five seconds. Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 SCROLL control knob to the right or left to adjust the sound level from the right or left side speakers. Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary TUNE/SCROLL control knob again to exit setting tone, balance, and fade.
212 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 16-Digit Character Display Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R & B Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 • DISC Play/Pause - You can toggle between playing the DVD and pausing the DVD by pushing the SELECT button (if equipped). • DVD Play Options - Selecting the DVD Play Options will display the following: • Subtitle – Repeatedly pressing SELECT will switch subtitles to different subtitle languages that are available on the disc (if equipped). • Audio Stream – Repeatedly pressing SELECT will switch to different audio languages (if supported on the disc) (if equipped).
214 UNDERSTANDING YOUR INSTRUMENT PANEL TUNE/SCROLL control knob to adjust the minutes. Press the TUNE/SCROLL control knob again to save changes. down and selecting ⬙other.⬙ Enter the country code using the TUNE/SCROLL control knob to scroll up and down to select the number and then push to select. • Player Defaults - Selecting this item will allow the user to scroll through the following items and set defaults according to customer preference.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 Aspect Ratio — If Equipped Selecting this item allows you to choose between wide screen, pan scan, and letter box. AutoPlay — If Equipped When this is set to On and a DVD video is inserted, it will bypass the DVD menu screen and automatically play the movie. In some rare cases, the DVD player may not auto-play the main title. In such cases, use the MENU button on the remote control to select desired title to play.
216 UNDERSTANDING YOUR INSTRUMENT PANEL Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 These buttons tune the radio to the stations that you commit to pushbutton memory {12 AM, 12 FM, and 12 Satellite (if equipped) stations}. DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 Radio display will show ⬙LOADING DISC⬙ when the disc is loading and “READING DISC” when the radio is reading the disc. CAUTION! This CD player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. Eject Button — Ejecting Compact Disc(s) Press the EJECT button and the pushbutton with the corresponding number (1-6) where the CD was loaded and the disc will unload and move to the entrance for easy removal.
218 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF (CD MODE) Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released, or RW or another CD button is pressed. The RW (Rewind) button works in a similar manner. AM or FM Button (CD MODE) Switches the radio into the AM or FM radio mode. Notes On Playing MP3/WMA Files The radio can play MP3/WMA files; however, acceptable MP3/WMA file recording media and formats are limited.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3/ WMA files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3/ WMA playback may result in longer disc loading times. frequencies in the following table are supported.
220 UNDERSTANDING YOUR INSTRUMENT PANEL ID3 Tag information for artist, song title, and album title are supported for ID3 version 1 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported. Playback of MP3/WMA Files When a medium containing MP3/WMA data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3/WMA files.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 INFO Button (DISC Mode for MP3/WMA Play) Pressing the INFO button repeatedly will scroll through the following TAG information: Song Title, Artist, File Name, and Folder Name (if available). Press the INFO button once more to return to ⬙elapsed time⬙ priority mode. Press and hold the INFO button for three seconds or more and radio will display song titles for each file. Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display.
222 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Press the TIME button to change the display from elapsed playing time to time of day. The time of day will display for five seconds. Operating Instructions - uconnect威 studios (Satellite Radio) (If Equipped) Refer to “uconnect威 studios (Satellite Radio)” in this section. RW/FF (Auxiliary Mode) No function.
UNDERSTANDING YOUR INSTRUMENT PANEL 223 intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. DTS™ ⬙DTS™⬙ and ⬙DTS™ 2.0⬙ are trademarks of Digital Theater Systems, Inc. AM/FM/CD/DVD RADIO (RER/REN) – IF EQUIPPED NOTE: The sales code is located on the lower right side of the unit’s faceplate. The REN and RER radios contain a CD/DVD player, USB port, and a 30-gigabyte hard drive (HDD).
224 UNDERSTANDING YOUR INSTRUMENT PANEL To Manually Set the Clock — RER/REN 1. Turn on the radio. 2. Touch the screen where the time is displayed. 3. Touch the screen where “User Clock” is displayed. The clock setting menu will appear on the screen. 4. To move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is displayed. To move the hour backward, touch the screen where the word “Hour” with the arrow pointing downward is displayed. 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 Show Time if Radio is Off When selected, this feature will display the time of day on the touch screen when the radio is turned off. Proceed as follows to change the current setting: 1. Turn on the radio. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “Show Time if Radio is Off.
226 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RES — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. TIME Button Press the TIME button to alternate locations of the time and frequency display. Clock Setting Procedure 1.
228 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the mid-range tones. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones. Push the rotary TUNE/SCROLL control knob a fourth time and BALANCE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 These buttons tune the radio to the stations that you commit to pushbutton memory (12 AM and 12 FM stations).
230 UNDERSTANDING YOUR INSTRUMENT PANEL If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. CAUTION! • This CD player will accept 4-3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels.
UNDERSTANDING YOUR INSTRUMENT PANEL 231 the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD and MP3 modes. TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display. RW/FF Press and hold the FF (Fast Forward) button and the CD player will begin to fast forward until FF is released, or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner.
232 UNDERSTANDING YOUR INSTRUMENT PANEL Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file normally. UDF and Apple HFS formats are not supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
234 UNDERSTANDING YOUR INSTRUMENT PANEL Loading times for playback of MP3 files may be affected by the following: • Media - CD-RW media may take longer to load than CD-R media • Medium formats - Multisession discs may take longer to load than non-multisession discs • Number of files and folders - Loading times will increase with more files and folders To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs.
UNDERSTANDING YOUR INSTRUMENT PANEL 235 SALES CODE RES/RSC — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) AND SIRIUS RADIO NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
236 UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. Voice Recognition System (Radio) — If Equipped Refer to “Voice Recognition System (VR)” in Section 3. Voice Recognition Button uconnect威 phone — If Equipped Press this button to operate the uconnect威 phone feature (if equipped).
UNDERSTANDING YOUR INSTRUMENT PANEL 237 5. To exit, press any button/knob or wait five seconds. The clock can also be set by pressing the SETUP button. For vehicles equipped with satellite radio, press the SETUP button, use the TUNE/SCROLL control to select SET CLOCK, and then follow the above procedure, starting at Step 2. For vehicles not equipped with satellite radio, press the SETUP button and then follow the above procedure, starting at Step 2.
238 UNDERSTANDING YOUR INSTRUMENT PANEL SCROLL control knob to the right or left to adjust the sound level from the right or left side speakers. Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary TUNE/SCROLL control knob again to exit setting tone, balance, and fade.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 Program Type Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 16-Digit Character Display Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R&B Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name.
240 UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button Press the button to select either AM or FM mode. SET/RND Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND button. The symbol SET 1 will now show in the display window. Select the button (1 to 6) you wish to lock onto this station and press and release that button.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 Operation Instructions — CD MODE for CD and MP3 Audio Play NOTE: • The ignition switch must be in the ON or ACC position to operate the radio. • This radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable compact discs (CD-RW), compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks. Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up.
242 UNDERSTANDING YOUR INSTRUMENT PANEL EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the CD is not removed, the radio will reinsert the CD but will not play it. A disc can be ejected with the radio and ignition OFF. NOTE: Ejecting with the ignition OFF is not allowed on convertible or soft-top models (if equipped). SEEK Button Press the right SEEK button for the next selection on the CD.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the right SEEK button to move to the next randomly selected track. Press the SET/RND button a second time to stop Random Play.
244 UNDERSTANDING YOUR INSTRUMENT PANEL exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.) • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙.⬙ and a threecharacter extension) • Level 2: 31 (including a separator ⬙.⬙ and a threecharacter extension) Multisession disc formats are supported by the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 MPEG Specification MPEG-2 Audio Layer 3 Sampling Bit Rate (kbps) Frequency (kHz) 160, 128, 144, 112, 96, 80, 64, 24, 22.05, 16 56, 48, 40, 32, 24, 16, 8 ID3 Tag information for artist, song title, and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported.
246 UNDERSTANDING YOUR INSTRUMENT PANEL begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain playable files). The folder list will time out after five seconds. INFO Button (CD Mode for MP3 Play) Pressing the INFO button repeatedly will scroll through the following TAG information: Song Title, Artist, File Name, and Folder Name (if available). Press the INFO button once more to return to ⬙elapsed time⬙ priority mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 Operating Instructions - uconnect威 phone (If Equipped) Refer to “uconnect威 phone” in Section 3. This feature allows you to plug an iPod威 into the vehicle’s sound system through a 16–pin connector using the provided interface cable. Operating Instructions - uconnect威 studios (Satellite Radio) (If Equipped) Refer to “uconnect威 studios (Satellite Radio)” in this section. UCI supports Mini, 4G, Photo, Nano, 5G iPod威 and iPhone威 devices.
248 UNDERSTANDING YOUR INSTRUMENT PANEL Connecting The iPod姞 Use the optional connection cable to connect an iPod威 to the vehicle’s 16–pin connector port (which is located in the glove compartment on some vehicles). Once the iPod威 is connected and synchronized to the vehicle’s UCI system (iPod威 may take a few seconds to connect), the iPod威 starts charging and is ready for use by pressing radio switches, as described below.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 Play Mode When switched to UCI mode, the iPod威 automatically starts Play mode. In Play mode, you may use the following buttons on the radio faceplate to control the iPod威 and display data: • Use the TUNE control knob to select the next or previous track. • Turning it clockwise (forward) by one click, while playing a track, skips to the next track.
250 UNDERSTANDING YOUR INSTRUMENT PANEL • While a track is playing, press the INFO button to see the associated metadata (Artist, track title, album, etc.) for that track. Pressing the INFO button again jumps to the next screen of data for that track. Once you have seen all screens, the last INFO button press will take you back to the play mode screen on the radio. • Pressing the REPEAT button will change the iPod威 mode to repeat the current playing track.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 • During all List modes, the iPod威 displays all lists in “wrap-around” mode. So if the track is at the bottom of the list just turn the wheel backwards (counter-clockwise) to get to the track faster. • In List mode, the radio PRESET Buttons are used as shortcuts to the following lists on the iPod威.
252 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! • Leaving the iPod威 (or any supported device) anywhere in the vehicle in extreme heat or cold can alter the operation, or damage the device. Follow the device manufacturer’s guidelines. • Placing items on the iPod威, or connections to the iPod威 in the vehicle, can cause damage to the device and/or to the connectors. WARNING! Do not plug in or remove the iPod威 while driving. Failure to following this warning could result in an accident.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 number 888-539-7474, or visit the Sirius web site at www.sirius.com, or at www.siriuscanada.ca for Canadian residents. Sirius ID number will display. The Sirius ID number display will time out in two minutes. Press any button on the radio to exit this screen.
254 UNDERSTANDING YOUR INSTRUMENT PANEL bikes should be placed as far rearward as possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception Quality Satellite reception may be interrupted due to one of the following reasons: • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception in the form of short audio mutes.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 INFO Button Pressing the INFO button will cycle the display information between Artist, Song Title, and Composer (if available). Also, pressing and holding the INFO button for an additional three seconds will make the radio display the Song Title all of the time (press and hold again to return to normal display). RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next channel in the direction of the arrows.
256 UNDERSTANDING YOUR INSTRUMENT PANEL SETUP Button Pressing the SETUP button allows you to select the following items: • Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number. This number is used to activate, deactivate, or change the Sirius subscription. SET Button – To Set the Pushbutton Memory When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 uconnect studios姞 (SIRIUS BACKSEAT TV™) — IF EQUIPPED Satellite video uses direct satellite receiver broadcasting technology to provide streaming video. The subscription service provider is SIRIUS Satellite Radio. SIRIUS Backseat TV™ offers three video channels for family entertainment, directly from its satellites and broadcasting studios. powered remote control, and two headsets. Refer to your VES™ User’s Manual for detailed operating instructions.
258 UNDERSTANDING YOUR INSTRUMENT PANEL Remote Control Location REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. Remote Sound System Controls (Back View of Steering Wheel) The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 Pressing the center button will make the radio switch between the various modes available (AM/FM/TAPE/ CD, Etc.). The left-hand control is a rocker-type switch with a pushbutton in the center. The function of the left-hand control is different depending on which mode you are in. The following describes the left-hand control operation in each mode.
260 UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD MAINTENANCE To keep a CD/DVD in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzene, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6.
UNDERSTANDING YOUR INSTRUMENT PANEL 261 CLIMATE CONTROLS Manual Air Conditioning And Heating System — If Equipped The controls for the heating/air conditioning and ventilation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desired interior conditions. 4 Manual Air Conditioning And Heating Controls The instrument panel features four dual-vane airflow registers.
262 UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control The blower control rotary knob (on the left) controls the blower and can be set to one of four speeds, and OFF. The blower fan motor will remain on until the system is turned to the OFF position or the ignition is turned OFF. NOTE: For vehicles equipped with Remote Start, the climate controls will not function during Remote Start operation if the blower control is left in the “O” (Off) position.
UNDERSTANDING YOUR INSTRUMENT PANEL 263 Defrost Air is directed to the windshield through the outlets at the base of the windshield. Air is also directed to the front door windows through the side window demister grilles. Some airflow is delivered to the floor while in defrost so that comfort can be maintained. Defrost/Floor Air flows through the front and rear floor outlets and the outlets at the base of the windshield.
264 UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation The recirculation feature can be selected with the mode control knob. You may choose between Bi-Level Recirculation and Panel Recirculation air outlets while in this mode. Normally, air enters from outside the vehicle. However, when in “Recirculation” mode air inside the vehicle is re-used. Use this mode to rapidly cool the inside of the vehicle. The “Recirculation” mode can also be used to temporarily block out outside odors, smoke, and dust.
UNDERSTANDING YOUR INSTRUMENT PANEL 265 be used for front seat occupants only. The HI AUTO position should be used when more airflow is desired, or when rear seat occupants are present. Dial in the comfort setting you would like the system to maintain by rotating the driver’s or passenger’s control knob. Once the comfort level is selected, the system will maintain that level automatically using the heating system.
266 UNDERSTANDING YOUR INSTRUMENT PANEL respectively. With the temperature setting in these positions, the system does not attempt automatic comfort control. Air Conditioning The air conditioning in this system is automatic. Pressing this button while in AUTO mode will cause the LED to flash three times and remain off. This indicates that the system is in AUTO and requesting the air conditioning is not necessary. Recirculation The system will automatically control recirculation.
UNDERSTANDING YOUR INSTRUMENT PANEL 267 • Most of the time, when in Automatic operation, you can temporarily put the system into Recirculation mode by pressing the “Recirculation” button. However, under certain conditions in automatic the system is blowing air out of the defrost vents. When these conditions are present, and the “Recirculation” button is pressed, the indicator will flash and remain off. This tells you that you are unable to go into Recirculation mode at this time.
268 UNDERSTANDING YOUR INSTRUMENT PANEL
UNDERSTANDING YOUR INSTRUMENT PANEL 269 NOTE: Regardless of the type of operation, when a temperature knob is set to the full clockwise or full counterclockwise position, the system will deliver full hot or full cold air out of the ducts, respectively. The operator can override the AUTO mode setting and select the direction of the air by rotating the right mode knob to one of the following positions. When the Mode is set to any position other than AUTO, the automatic control of air temperature is disabled.
270 UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Air flows both through the outlets located in the instrument panel and those located on the floor. Air flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to block airflow. The center console outlets deliver conditioned air while the floor outlets deliver heated air. Panel Air flows through the outlets located in the instrument panel.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 captured interior air to condense on windows and hamper visibility. For this reason, the system will not allow “Recirculation” mode to be selected while in the defrost or defrost/floor modes. Attempting to use Recirculation while in these modes will cause the LED in the button to blink and then turn off. Operating Tips Window Fogging Windows will fog on the inside when the humidity inside the vehicle is high.
272 UNDERSTANDING YOUR INSTRUMENT PANEL When using the air conditioner in extremely heavy traffic, in hot weather, especially when towing a trailer, additional engine cooling may be required. If this situation is encountered, operate the transmission in a lower gear to increase engine RPM, coolant flow and fan speed. When stopped in heavy traffic, it may be necessary to shift into NEUTRAL and depress the accelerator slightly for fast idle operation to increase coolant flow and fan speed.
UNDERSTANDING YOUR INSTRUMENT PANEL 273 Operating Tips Chart 4
STARTING AND OPERATING CONTENTS 䡵 Starting Procedure . . . . . . . . . . . . . . . . . . . . . 280 ▫ Brake/Transmission Shift Interlock System . . 287 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 280 ▫ Brake/Transmission Interlock Manual Override . . . . . . . . . . . . . . . . . . . . . . . . . . 287 ▫ Extremely Cold Weather (Below ⫺20°F Or ⫺29°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281 ▫ Five–Speed Automatic Transmission . . . . . . .
276 STARTING AND OPERATING ▫ Quadra-Trac II威 Operating Instructions/Precautions — If Equipped . . . . 297 ▫ Shift Positions . . . . . . . . . . . . . . . . . . . . . . 298 ▫ Shifting Procedures . . . . . . . . . . . . . . . . . . . 298 ▫ Quadra-Drive II威 System — If Equipped . . . . 301 䡵 On-Road Driving Tips . . . . . . . . . . . . . . . . . . 301 䡵 Off-Road Driving Tips . . . . . . . . . . . . . . . . . . 302 ▫ When To Use 4WD Low Range — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 277 ▫ HDC (Hill Descent Control) (4WD Models With NV245 Two–Speed Transfer Case Only) . . . . . . . . . . . . . . . . . . . . . . . . . 323 ▫ ESP/BAS Warning Light And ESP/TCS Indicator Light . . . . . . . . . . . . . . . . . . . . . . 325 䡵 Tire Safety Information ▫ Compact Spare Tire — If Equipped . . . . . . . 338 ▫ Limited-Use Spare — If Equipped . . . . . . . . 339 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . 340 ▫ Tread Wear Indicators . . . . . . . . . . . .
278 STARTING AND OPERATING 䡵 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . 355 ▫ E-85 General Information . . . . . . . . . . . . . . . 361 ▫ 3.7 And 4.7L Engine . . . . . . . . . . . . . . . . . . 355 ▫ Ethanol Fuel (E-85) . . . . . . . . . . . . . . . . . . . 362 ▫ 5.7L Engine . . . . . . . . . . . . . . . . . . . . . . . . 355 ▫ Fuel Requirements . . . . . . . . . . . . . . . . . . . 362 ▫ Reformulated Gasoline . . . . . . . . . . . . . . . .
STARTING AND OPERATING 279 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 369 䡵 Snow Plow . . . . . . . . . . . . . . . . . . . . . . . . . . 382 ▫ Common Towing Definitions . . . . . . . . . . . . 369 䡵 Recreational Towing (Behind Motorhome, Etc.) . . . . . . . . . . . . . . . . 382 ▫ Trailer Hitch Classification . . . . . . . . . . . . . . 372 ▫ Trailer Towing Weights (Maximum Trailer Weight Ratings) . . . . . . . . . . . . . . . . . . . . . 373 ▫ Trailer And Trailer Tongue Weight .
280 STARTING AND OPERATING STARTING PROCEDURE Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition.
STARTING AND OPERATING 281 Extremely Cold Weather (Below ⫺20°F or ⫺29°C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your authorized dealer) is recommended. If Engine Fails To Start WARNING! • Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury.
282 STARTING AND OPERATING release it as soon as the starter engages. The starter motor will disengage automatically in 10 seconds. Once this occurs, release the accelerator pedal, turn the ignition switch to the LOCK position, wait 10 to 15 seconds, then repeat the normal starting procedure. • Low Oil Pressure Light is off. Cold Weather Precautions Operation in ambient temperature below 32°F (0°C) may require special considerations. The following chart suggests these options.
STARTING AND OPERATING 283 NOTE: • Use of Climatized ULSD Diesel Fuel or Number 1 ULSD Diesel Fuel results in a noticeable decrease in fuel economy. • Climatized ULSD Diesel Fuel is a blend of Number 2 ULSD and Number 1 ULSD Diesel Fuels, which reduces the temperature at which wax crystals form in fuel. NOTE: This engine requires the use of “Ultra Low Sulfur Diesel Fuel.” Use of incorrect fuel could result in exhaust system damage.
284 STARTING AND OPERATING depending on engine temperature. When the “Wait To Start” goes out, the engine is ready to start. 4. Tip Start Feature Do not press the accelerator. Use the Fob with Integrated Key (FOBIK) to briefly turn the ignition switch to the START position and then release it. The starter motor will continue to run, and it will automatically disengage when the engine is running. If the engine fails to start, the starter will disengage automatically in 20 seconds.
STARTING AND OPERATING 285 Engine Idling - In Cold Weather Avoid prolonged idling in ambient temperatures below 0°F (-18°C). Long periods of idling may be harmful to your engine because combustion chamber temperatures can drop so low that the fuel may not burn completely. Incomplete combustion allows carbon and varnish to form on piston rings and injector nozzles. Also, the unburned fuel can enter the crankcase, diluting the oil and causing rapid wear to the engine.
286 STARTING AND OPERATING • 5.7L Engine — bundled and fastened to the injector harness. • 3.0L Diesel Engine — on the passenger side of the vehicle, mounted on a stud between the fresh airbox and coolant reservoir. WARNING! Remember to disconnect the cord before driving. Damage to the 110-115 Volt AC electrical cord could cause electrocution.
STARTING AND OPERATING 287 WARNING! It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your foot is firmly on the brake pedal.
288 STARTING AND OPERATING 5. Using the screwdriver, reach into the manual override opening. Press and hold the shift lock lever down. Have your vehicle inspected by your local authorized dealer, if the shift lock manual override has been used. Five–Speed Automatic Transmission The electronically controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle, may be somewhat abrupt.
STARTING AND OPERATING 289 PARK This gear position supplements the parking brake by locking the transmission. The engine can be started in this range. Never use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply the parking brake first, then place the shift lever into the PARK position. WARNING! • Never use the PARK position as a substitute for the parking brake.
290 STARTING AND OPERATING NOTE: Towing the vehicle, coasting, or driving for any other reason with the shift lever in NEUTRAL can result in severe transmission damage. Refer to “Recreational Towing” in Section 5 and “Towing a Disabled Vehicle” in Section 6 of this manual. DRIVE Shift into DRIVE only when the vehicle is at a complete stop and the brakes are firmly applied. The transmission automatically upshifts through fifth gear.
STARTING AND OPERATING 291 transmission will downshift to 4th gear and the display will show 4. Another tap to the left (-) will shift the transmission into 3rd gear. 4.7L and 5.7L Engine On vehicles equipped with 4.7L or 5.7L engines, use of ERS (or TOW/HAUL mode) also enables an additional underdrive gear which is not normally used during through-gear accelerations. This additional gear improves vehicle performance and cooling capability when towing a trailer on certain grades.
292 STARTING AND OPERATING left “D(-)” and hold it there. The transmission will shift to the range from which the vehicle can best be slowed down. Overdrive Operation The automatic transmission includes an electronically controlled Overdrive (5th gear for 3.7L and 3.0L diesel engine, 4th and 5th gears for 4.7L and 5.7L engines).
STARTING AND OPERATING 293 OVER TEMP” message may display, and the transmission may downshift out of Overdrive until the transmission cools down. After cool down, the transmission will resume normal operation. overheating or failure due to excessive shifting. When operating in TOW/HAUL mode, the transmission will shift into direct gear and Overdrive will be enabled under steady cruise conditions.
294 STARTING AND OPERATING activated. Pressing the switch a second time restores normal operation. If the TOW/HAUL mode is desired, the switch must be pressed each time the engine is started. Transmission Limp Home Mode Transmission function is monitored for abnormal conditions. If a condition is detected that could result in transmission damage, the transmission limp home mode will be engaged. In this mode, the transmission will remain in the current gear (3.7L and 3.
STARTING AND OPERATING 295 drops below a calibrated speed, or during acceleration, the clutch automatically and smoothly disengages. The feature is operational in Overdrive and in DRIVE. NOTE: • The torque converter clutch will not engage until the transmission fluid and engine coolant are warm [usually after 1 to 3 miles (1.6 to 4.8 km) of driving].
296 STARTING AND OPERATING The least amount of accelerator pedal pressure to maintain the rocking motion, without spinning the wheels or racing the engine, is most effective. Racing the engine or spinning the wheels, due to the frustration of not freeing the vehicle, may lead to transmission overheating and failure. Allow the engine to idle with the shift lever in NEUTRAL for at least one minute after every five rocking-motion cycles.
STARTING AND OPERATING 297 Quadra-Trac II姞 Operating Instructions/Precautions — If Equipped The Quadra-Trac II威 transfer case is fully automatic in the normal driving 4WD HI mode. The Quadra-Trac II威 transfer case provides three mode positions — 4WD HI, NEUTRAL, and 4WD LOW. This transfer case is fully automatic in the 4WD HI mode.
298 STARTING AND OPERATING Shift Positions Shifting Procedures For additional information on the appropriate use of each transfer case mode position, see the information below: 4WD HI to 4WD LOW With the vehicle at speeds of 0 to 3 mph (0 to 5 km/h), key ON or engine running, shift the transmission into NEUTRAL, and raise the transfer case T-handle. The “4WD LOW” indicator light in the instrument cluster, will begin to flash and remain on solid when the shift is complete. Release the T-handle.
STARTING AND OPERATING 299 “4WD LOW” indicator light in the instrument cluster, will flash and go out when the shift is complete. Release the T-handle. Shifter T-Handle 4WD LOW to 4WD HI With the vehicle at speeds of 0 to 3 mph (0 to 5 km/h), key ON or engine running, shift the transmission into NEUTRAL, and raise the transfer case T-handle.
300 STARTING AND OPERATING NEUTRAL Shift Procedure 1. Key ON, engine off. 2. Vehicle stopped, with foot on brake. 3. Place transmission into NEUTRAL. 4. Hold down the NEUTRAL “pin” switch (with a pen, etc.) for four seconds until the LED lamp by the switch starts to blink indicating shift in progress. The lamp will stop blinking (stay on solid) when the NEUTRAL shift is complete. A “4WD SYSTEM IN NEUTRAL” message will display on the EVIC (Electronic Vehicle Information Center).
STARTING AND OPERATING 301 Quadra-Drive II姞 System — If Equipped The optional Quadra-Drive II威 System features three torque transfer couplings. The couplings include ELSD (Electronic Limited-Slip Differential) front and rear axles and Quadra-Trac II威 transfer case. The optional ELSD axles are fully automatic and require no driver input to operate. Under normal driving conditions, the units function as standard axles, balancing torque evenly between left and right wheels.
302 STARTING AND OPERATING OFF-ROAD DRIVING TIPS NOTE: Prior to off-road driving, remove the front air dam to prevent damage. The front air dam is attached to the lower front fascia with quarter turn fasteners, and can be removed by hand. When To Use 4WD LOW Range — If Equipped When off-road driving, shift to 4WD LOW for additional traction. This range should be limited to extreme situations such as deep snow, mud, or sand where additional low speed pulling power is needed.
STARTING AND OPERATING 303 Flowing Water If the water is swift flowing and rising (as in storm run-off) avoid crossing until the water level recedes and/or the flow rate is reduced. If you must cross flowing water avoid depths in excess of 9 in (23 cm). The flowing water can erode the streambed causing your vehicle to sink into deeper water. Determine exit point(s) that are downstream of your entry point to allow for drifting.
304 STARTING AND OPERATING Hill Climbing NOTE: Before attempting to climb a hill, determine the conditions at the crest and/or on the other side. Before climbing a steep hill, shift the transmission to a lower gear and shift the transfer case to 4WD LOW. Use first gear and 4WD LOW for very steep hills. If you stall or begin to lose forward motion while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brakes. Restart the engine, and shift into REVERSE.
STARTING AND OPERATING 305 Traction Downhill Shift the transmission into a low gear, and the transfer case into 4WD LOW range. Let the vehicle go slowly down the hill with all four wheels turning against engine compression drag. This will permit you to control the vehicle speed and direction. When descending mountains or hills, repeated braking can cause brake fade with loss of braking control. Avoid repeated heavy braking by downshifting the transmission whenever possible.
306 STARTING AND OPERATING WARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent an accident. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. • If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.
STARTING AND OPERATING 307 WARNING! WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. Do not use Automatic Transmission Fluid (ATF), or other types of power steering fluids, when servicing the power steering system of this vehicle. Damage to the power steering system can result from the use of the wrong power steering fluid.
308 STARTING AND OPERATING WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. NOTE: The Brake Warning Light indicates only that the parking brake is applied. It does not indicate the degree of brake application. If necessary, add fluid to restore to the proper indicated level.
STARTING AND OPERATING 309 the shift lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of PARK. WARNING! • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury. Also, be certain to leave the transmission in PARK. Failure to do so may allow the vehicle to roll and cause damage or injury. • Leaving unattended children in a vehicle is dangerous for a number of reasons.
310 STARTING AND OPERATING wheel lock-up and help avoid skidding on slippery surfaces. All vehicle wheels and tires must be the same size and type, and tires must be properly inflated, to produce accurate signals for the computer. WARNING! Significant over or under-inflation of tires or mixing sizes of tires or wheels on the vehicle can lead to loss of braking effectiveness. The ABS conducts a low-speed self-test at about 12 mph (20 km/h).
STARTING AND OPERATING 311 WARNING! (Continued) • The ABS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents. • The capabilities of an ABS equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user’s safety or the safety of others.
312 STARTING AND OPERATING • Do not drive too fast for road conditions, especially when roads are wet or slushy. A wedge of water can build up between the tire tread and the road. This hydroplaning action can cause loss of traction, braking ability, and control. • After going through deep water or a car wash, brakes may become wet, resulting in decreased performance and unpredictable braking action. Dry the brakes by gentle, intermittent pedal action while driving at very slow speeds.
STARTING AND OPERATING 313 WARNING! ABS (Anti-Lock Brake System) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. ABS cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
314 STARTING AND OPERATING benefit of the system, you must apply continuous braking pressure during the stopping sequence (do not “pump” the brakes). Do not reduce brake pedal pressure unless braking is no longer desired. Once the brake pedal is released, the BAS is deactivated. WARNING! BAS (Brake Assist System) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.
STARTING AND OPERATING 315 NOTE: Anytime the ESP system is in the “Full Off” mode, ERM is disabled. Refer to ESP (Electronic Stability Program) for a complete explanation of the available ESP modes. WARNING! Many factors, such as vehicle loading, road conditions and driving conditions, influence the chance that wheel lift or rollover may occur. ERM cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles.
316 STARTING AND OPERATING • Understeer - when the vehicle is turning less than appropriate for the steering wheel position. The ESP/TCS Indicator Light located in the instrument cluster, starts to flash as soon as the tires lose traction and the ESP system becomes active. The ESP/TCS Indicator Light also flashes when TCS is active. If the ESP/TCS Indicator Light begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible.
STARTING AND OPERATING 317 High Range (4WD Models) or 2WD Models On This is the normal operating mode for ESP in 4WD HIGH range and in 2WD vehicles. Whenever the vehicle is started or the transfer case (if equipped) is shifted from 4WD LOW range or NEUTRAL back to 4WD HIGH range, the ESP system will be in this “On” mode. This mode should be used for most driving situations. ESP should only be turned to “Partial Off” or “Full Off” mode for specific reasons as noted below.
318 STARTING AND OPERATING NOTE: To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand, or gravel, it may be desirable to switch to the “Partial Off” mode by pressing the ESP OFF switch. Once the situation requiring ESP to be switched to the “Partial Off” mode is overcome, turn ESP back on by momentarily depressing the ESP OFF switch. This may be done while the vehicle is in motion.
STARTING AND OPERATING 319 WARNING! With the ESP switched off, the enhanced vehicle stability offered by ESP and ERM are unavailable. In an emergency evasive maneuver, the ESP and ERM systems will not engage to assist in maintaining stability. The “Full Off” ESP mode is intended for off-road use only. 4WD Low Range Full Off This is the normal operating mode for ESP in 4WD LOW range.
320 STARTING AND OPERATING WARNING! With the ESP switched off, the enhanced vehicle stability offered by ESP and ERM are unavailable. In an emergency evasive maneuver, the ESP and ERM systems will not engage to assist in maintaining stability. The “Full Off” mode is intended for offroad use only. TSC (Trailer Sway Control) TSC uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appropriate actions to attempt to stop the sway.
STARTING AND OPERATING 321 period of time after the driver takes their foot off of the brake pedal. If the driver does not apply the throttle during this short period of time, the system will release brake pressure and the vehicle will roll down the hill. The system will release brake pressure in proportion to amount of throttle applied as the vehicle starts to move in the intended direction of travel.
322 STARTING AND OPERATING WARNING! WARNING! (Continued) • If you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision with another vehicle or object behind you.
STARTING AND OPERATING 323 HDC (Hill Descent Control) (4WD Models With NV245 Two–Speed Transfer Case Only) HDC maintains vehicle speed while descending hills during off-road driving situations and is available in 4WD LOW range only. To enable HDC (transfer case must be in 4WD LOW range), press the HDC switch. If the HDC switch is pressed when the vehicle is not in 4WD LOW range, the light in the switch will flash for five seconds and HDC will not be enabled.
324 STARTING AND OPERATING and will only activate when the vehicle is descending a hill. It will usually not activate on level ground. The HDC speed may be adjusted by the driver to suit the driving conditions. The speed corresponds to the transmission gear selected. • 1st = 1 mph (1.6 km/h) • 2nd = 2.5 mph (4 km/h) • 3rd = 4 mph (6 km/h) • 4th = 5.5 mph (9 km/h) • 5th = 7.5 mph (12 km/h) • REVERSE = 1 mph (1.6 km/h) • NEUTRAL = 2.
STARTING AND OPERATING 325 WARNING! HDC is only intended to assist the driver in controlling vehicle speed when descending hills. The driver must remain attentive to the driving conditions and is responsible for maintaining a safe vehicle speed. ESP/BAS Warning Light And ESP/TCS Indicator Light The malfunction indicator lamp for the ESP is combined with the BAS indicator.
326 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
STARTING AND OPERATING 327 • Temporary spare tires are high-pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation. Example: T145/80D18 103M. Tire Sizing Chart • High flotation tire sizing is based on U.S. design standards and it begins with the tire diameter molded into the sidewall. Example: 31x10.5 R15 LT. EXAMPLE: Size Designation: P = Passenger car tire size based on U.S.
328 STARTING AND OPERATING EXAMPLE: R = Construction code — ⬙R⬙ means radial construction —⬙D⬙ means diagonal or bias construction 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved unde
STARTING AND OPERATING 329 EXAMPLE: Load Identification: ⴖ....blank....
330 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
STARTING AND OPERATING 331 Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires.
332 STARTING AND OPERATING axles must not be exceeded. For further information on GAWRs, vehicle loading, and trailer towing, refer to “Vehicle Loading” in this section. To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard.
STARTING AND OPERATING 333 NOTE: • The following table shows examples on how to calculate total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load carry capacity of your vehicle. • For the following example, the combined weight of occupants and cargo should never exceed 865 lbs (392 kg).
334 STARTING AND OPERATING
STARTING AND OPERATING 335 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
336 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement.
STARTING AND OPERATING 337 CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage it. Inflation pressures specified on the placard are always cold tire inflation pressure. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three-hour period.
338 STARTING AND OPERATING loading may be required for high-speed vehicle operation. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. WARNING! High speed driving with your vehicle at or above maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Do not drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
STARTING AND OPERATING 339 WARNING! CAUTION! Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). Temporary use spare tires have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to follow the warnings, which apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control.
340 STARTING AND OPERATING WARNING! WARNING! The limited-use spare tires are for emergency use only. Installation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than 50 mph (80 km/h). Keep inflated to the cold tire inflation pressure listed on either your tire placard or limited-use spare tire and wheel assembly. Replace (or repair) the original tire at the first opportunity and reinstall it on your vehicle.
STARTING AND OPERATING 341 Many states have laws requiring tire replacement at this point. Life Of Tire The service life of a tire is dependent upon various factors including but not limited to: • Driving style • Tire pressure 5 • Distance driven WARNING! 1 — Worn Tire 2 — New Tire These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm).
342 STARTING AND OPERATING Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manufacturer strongly recommends that you use tires equivalent to the originals in size, quality and performance when replacement is needed.
STARTING AND OPERATING 343 WARNING! (Continued) • Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings. TIRE CHAINS Certain models have sufficient tire-to-body clearance to allow use of tire chains. Install chains on rear tires only.
344 STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, handling, and braking functions. For these reasons, they wear at unequal rates and develop irregular wear patterns. The suggested rotation method is the “forward-cross” shown in the following diagram. These effects can be reduced by timely rotation of tires.
STARTING AND OPERATING 345 TIRE PRESSURE MONITOR SYSTEM (TPMS) The Tire Pressure Monitoring System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold tire pressure. The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning threshold for any reason, including low temperature effects, or natural pressure loss through the tire. The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12°F (–11°C).
346 STARTING AND OPERATING For example, your vehicle has a recommended cold (parked for more than three hours) tire pressure of 33 psi (227 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 28 psi (193 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressure to approximately 24 psi (165 kPa). This tire pressure is sufficiently low enough to turn ON the Tire Pressure Monitoring Telltale Light.
STARTING AND OPERATING 347 NOTE: • The TPMS is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. • Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
348 STARTING AND OPERATING A tire pressure monitoring sensor is located in the spare wheel, if the vehicle is equipped with a matching full-size spare wheel and tire assembly. The matching full-size spare tire can be used in place of any of the four road tires. A low spare tire will not cause the Tire Pressure Monitoring Telltale Light to illuminate, a warning message to appear, or the chime to sound.
STARTING AND OPERATING 349 3. Lots of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPM sensors. NOTE: • If your vehicle is equipped with a matching full-size spare wheel and tire assembly, it has a tire pressure monitoring sensor, and can be monitored by the Tire Pressure Monitoring System (TPMS).
350 STARTING AND OPERATING TPM SYSTEM” message will be displayed for 75 seconds, and the Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds and then remain on solid. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the spare tire, the TPMS will update automatically and the Tire Pressure Monitoring Telltale Light will turn OFF, as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires.
STARTING AND OPERATING 351 spare tire can be used in place of any of the four road tires. A low spare tire will set the “SPARE LOW PRESSURE” message, but it will not cause the Tire Pressure Monitoring Telltale Light to illuminate or the chime to sound. Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster, and an audible chime will be activated, when one or more of the four active road tire pressures are low.
352 STARTING AND OPERATING once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information. CHECK TPM SYSTEM Warning The Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds, and remain on solid when a system fault is detected. The system fault will also sound a chime. The EVIC will display a “CHECK TPM SYSTEM” message for three seconds.
STARTING AND OPERATING 353 If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the Tire Pressure Monitoring Telltale Light will no longer flash, the ⬙CHECK TPM SYSTEM⬙ message will not be present, and a pressure value will be displayed instead of dashes. A system fault can occur by any of the following: 1.
354 STARTING AND OPERATING show the low tire pressure value “flashing.” Driving the vehicle for up to 20 minutes above 15 mph (24 km/h) will turn OFF the Tire Pressure Monitoring Telltale Light as long as none of road tires are below the low pressure warning threshold. The EVIC will also display a “SPARE LOW PRESSURE” message, and the graphic display will show a tire pressure value in place of the “flashing” low tire pressure value.
STARTING AND OPERATING 355 be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
356 STARTING AND OPERATING for optimum performance. The use of premium gasoline is not recommended, as it will not provide any benefit over regular gasoline in these engines. Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required.
STARTING AND OPERATING 357 CAUTION! DO NOT use gasoline containing Methanol. Use of these blends may result in starting and drivability problems and may damage critical fuel system components. Problems that result from using methanol/gasoline blends are not the responsibility of the manufacturer. While MTBE is an oxygenate made from Methanol, it does not have the negative effects of Methanol. E-85 Usage In Non-Flex Fuel Vehicles Non-FFV vehicles are compatible with gasoline containing 10% ethanol (E10).
358 STARTING AND OPERATING blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT. Gasoline blended with MMT reduces spark plug life and reduces emission system performance in some vehicles. The manufacturer recommends that gasoline without MMT be used in your vehicle. The MMT content of gasoline may not be indicated on the gasoline pump, therefore, you should ask your gasoline retailer if the gasoline contains MMT.
STARTING AND OPERATING 359 • The use of fuel additives which are now being sold as octane enhancers is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
360 STARTING AND OPERATING FUEL REQUIREMENTS (DIESEL ENGINES) NOTE: Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system. Use good quality diesel fuel from a reputable supplier. For most year-round service, No. 2 diesel fuel, meeting ASTM specification D-975 Grade S15, will provide good performance.
STARTING AND OPERATING 361 Diesel fuel is seldom completely free of water. To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the provided fuel/water separator drain. If you buy good quality fuel and follow the cold weather advice above, fuel conditioners should not be required in your vehicle. If available in your area, a high cetane “premium” diesel fuel may offer improved cold-starting and warm-up performance.
362 STARTING AND OPERATING CAUTION! Only vehicles with the E-85 fuel filler cap (gas cap) can operate on E-85. ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame.
STARTING AND OPERATING 363 For best results, a refueling pattern that avoids alternating between E-85 and unleaded gasoline is recommended. When you do switch fuel types it is recommended that: • you do not add less than 5 gal (19 L) when refueling • you drive the vehicle immediately after refueling for at least 5 mi (8 km) Observing these precautions will avoid possible hard starting and/or significant deterioration in drivability during warm up. NOTE: Use seasonally adjusted E-85 fuel (ASTM D5798).
364 STARTING AND OPERATING consumption. You can expect your MPG and your driving range to decrease by about 30% compared to gasoline operation. ADDING FUEL CAUTION! Replacement Parts All components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol compatible parts. DO NOT put gasoline in your diesel vehicle (if equipped). If you accidentally put gasoline in your vehicle, DO NOT start the engine.
STARTING AND OPERATING 365 CAUTION! Fuel Filler Cap • Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting aftermarket cap can cause the Malfunction Indicator Light (MIL) to illuminate, due to fuel vapors escaping from the system. • A poorly fitting gas cap may cause the Malfunction Indicator Light to turn on.
366 STARTING AND OPERATING WARNING! WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel when the engine is running. This is in violation of most state and federal fire regulations and will cause the malfunction indicator light to turn on. A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
STARTING AND OPERATING 367 CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler cap (gas cap). A poorly fitting cap could let impurities into the fuel system. VEHICLE LOADING Certification Label As required by National Highway Traffic Safety Administration regulations, your vehicle has a certification label affixed to the driver’s side door or B-Pillar.
368 STARTING AND OPERATING Each axle’s GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires, or wheels). Heavier axles or suspension components, sometimes specified by purchasers for increased durability, does not necessarily increase the vehicle’s GVWR. Tire Size The tire size on the label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size.
STARTING AND OPERATING 369 the front or rear axles has been exceeded, but the total load is within the specified GVWR. If so, weight must be shifted from front to rear, or rear to front, as appropriate until the specified weight limitations are met. Store the heavier items down low and be sure that the weight is distributed equally. Stow all loose items securely before driving.
370 STARTING AND OPERATING Gross Trailer Weight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its ⬙loaded and ready for operation⬙ condition. The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale.
STARTING AND OPERATING 371 some other connecting point of the vehicle. These kind of hitches are the most popular on the market today and they are commonly used to tow small- and mediumsized trailers. Weight-Distributing Hitch A weight-distributing hitch system works by applying leverage through spring (load) bars. They are typically used for heavier loads, to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s).
372 STARTING AND OPERATING Trailer Hitch Classification Your vehicle may be factory equipped for safe towing of trailers weighing over 3,500 lbs (1 587 kg) with the optional Trailer Tow Prep Package. See your authorized dealer for package content. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
STARTING AND OPERATING 373 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Model Model GCWR (Gross Combined Wt. Rating) Frontal Area 3.7L 3.7L 4.7L 4.7L 4.7L (w/ Trailer Tow Group IV) 4.7L (Laredo/ Limited)(w/ Trailer Tow Group IV) 5.7L 5.
374 STARTING AND OPERATING 3.0L Diesel (Limited) 3.0L Diesel (Overland) 3.0L Diesel 4x2 12,200 lbs (5 534 kg) 64 sq ft (5.95 sq m) 7,400 lbs (3 357 kg) 740 lbs (336 kg) 4x2 12,250 lbs (5 556 kg) 64 sq ft (5.95 sq m) 7,400 lbs (3 357 kg) 740 lbs (336 kg) 4x4 12,250 lbs (5 556 kg) 64 sq ft (5.95 sq m) 7,200 lbs (3 266 kg) Refer to local laws for maximum trailer towing speeds.
STARTING AND OPERATING 375 Trailer And Trailer Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels, or heavier in the rear, can cause the trailer to sway severely side-to-side which will cause loss of control of vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents.
376 STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information placard in the “Tire Safety Information” section of this manual for the maximum combined weight of occupants and cargo for your vehicle.
STARTING AND OPERATING 377 WARNING! (Continued) • Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: • When hauling cargo or towing a trailer, do not overload your vehicle or trailer. Overloading can cause a loss of control, poor performance or damage to brakes, axle, engine, transmission, steering, suspension, chassis structure or tires. • Safety chains must always be used between your vehicle and trailer.
378 STARTING AND OPERATING Towing Requirements — Tires Towing Requirements — Trailer Brakes − Do not attempt to tow a trailer while using a compact spare tire. − Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. − Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 379 CAUTION! WARNING! (Continued) If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. • Towing any trailer will increase your stopping distance. When towing, you should allow for additional space between your vehicle and the vehicle in front of you.
380 STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations.
STARTING AND OPERATING 381 Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Automatic Transmission The DRIVE range can be selected when towing. However, if frequent shifting occurs while in this range, the TOW/HAUL mode (if equipped), or a lower gear range, should be selected.
382 STARTING AND OPERATING Cooling System To reduce potential for engine and transmission overheating, take the following actions: − City Driving When stopped for short periods of time, shift the transmission into NEUTRAL and increase engine idle speed. WARNING! Do not add a snow plow, winches, or any other aftermarket equipment to the front of your vehicle. This could adversely affect the functioning of the airbag system and you could be injured. − Highway Driving Reduce speed.
STARTING AND OPERATING 383 Towing — Quadra-Trac I姞 (Single-Speed Transfer Case) 4WD Models Recreational towing is not allowed. This model does not have a NEUTRAL position in the transfer case. Towing — Quadra–Trac II姞 /Quadra–Drive II姞 4WD Models CAUTION! Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing.
384 STARTING AND OPERATING Hold down the NEUTRAL “pin” switch (with a pen, etc.) for four seconds until the LED lamp by the switch starts to blink, indicating shift in progress. The lamp will stop blinking (stay on solid) when the NEUTRAL shift is complete. A “4WD SYSTEM IN NEUTRAL” message will display on the EVIC (Electronic Vehicle Information Center). Refer to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. Neutral Switch 5. Start the engine. 6.
STARTING AND OPERATING 385 9. Shift the transmission into PARK. 10. Place the ignition key in the OFF position, and remove key. 11. Apply the parking brake. 12. Attach the vehicle to the tow vehicle with tow bar. 13. Release the parking brake. Shifting Out Of NEUTRAL Use the following procedure to prepare your vehicle for normal usage. 1. Depress the brake pedal. 2. Turn the ignition key ON, engine off. 3. Shift the transmission into NEUTRAL. 4. Shift the transfer case out of NEUTRAL.
386 STARTING AND OPERATING Hold down the NEUTRAL “pin” switch (with a pen, etc.) for four seconds until the LED lamp by the switch starts to blink, indicating shift in progress. The lamp will stop blinking (go out) when shift is complete. The “4WD SYSTEM IN NEUTRAL” message will no longer be displayed on the EVIC (Electronic Vehicle Information Center). Refer to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. Neutral Switch 5. Shift the transmission into PARK. 6.
STARTING AND OPERATING 387 NOTE: When shifting out of transfer case NEUTRAL, turning the engine OFF may be required to avoid gear clash. CAUTION! Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flashers . . . . . . . . . . . . . . . . 390 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . . 394 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 390 䡵 Jump-Starting . . . . . . . . . . . . . . . . . . . . . . . . 398 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 391 䡵 Emergency Tow Hooks — If Equipped . . . . . . 400 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . 392 䡵 Towing A Disabled Vehicle . .
390 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS The Hazard Warning flasher switch is located on the switch bank just above the climate controls. Press the switch to turn on the Hazard Warning flashers. When the Hazard Warning flasher switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off flashers. This is an emergency warning system and should not be used when the vehicle is in motion.
WHAT TO DO IN EMERGENCIES 391 CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads HOT (H), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on HOT (H), and you hear continuous chimes, turn the engine off immediately, and call for service. JACKING AND TIRE CHANGING WARNING! • Getting under a jacked-up vehicle is dangerous.
392 WHAT TO DO IN EMERGENCIES Jack Location The scissor-type jack and tire changing tools are located in the passenger side compartment, behind the second row seat. Spare Tire Stowage The spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. To remove or stow the spare, use the jack handle to rotate the “spare tire drive” nut. The nut is located under a plastic cover at the center-rear of the cargo floor area, just inside the liftgate opening.
WHAT TO DO IN EMERGENCIES 393 CAUTION! • The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. • When the spare is clear, tilt the retainer at the end of the cable and pull it through the center of the wheel. Preparations For Jacking Lowering/Raising Spare Tire Spare Tire Removal Fit the jack handle extension over the drive nut.
394 WHAT TO DO IN EMERGENCIES WARNING! Do not attempt to change a tire on the side of the vehicle closest to moving traffic. Pull far enough off the road to avoid being hit when operating the jack or changing the wheel. 2. Set the parking brake. 3. Place the shift lever into PARK. 4. Turn the ignition OFF. 5. Turn on the Hazard Warning flasher. 6. Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel.
WHAT TO DO IN EMERGENCIES 395 WARNING! (Continued) • Never start or run the engine with the vehicle on a jack. • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway, be extremely careful of motor traffic.
396 WHAT TO DO IN EMERGENCIES 3. Assemble the jack and jacking tools as shown. Connect jack handle driver (1) to two extensions (2), then to the lug wrench (3). 4. Locate the jack as shown. For the front axle, place it under the front lower control arm as shown. For the rear axle, place it under the axle near the wheel to be changed. Ensure the jack is closest to the inside of the wheel when jacking on the rear axle. Do not raise the vehicle until you are sure the jack is fully engaged.
WHAT TO DO IN EMERGENCIES 397 WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. Rear Jacking Location 5. Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. 7.
398 WHAT TO DO IN EMERGENCIES wheel nut tightness is 95 ft lbs (130 N·m). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station. 10. Lower the jack to its fully closed position. WARNING! A loose tire or jack, thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. 11. Secure the tire, jack, and tools in their proper locations.
WHAT TO DO IN EMERGENCIES 399 WARNING! • Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Do not lean over a battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush contaminated area immediately with large quantities of water. • A battery generates hydrogen gas which is flammable and explosive. Keep flame or spark away from the vent holes.
400 WHAT TO DO IN EMERGENCIES 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. 6. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan.
WHAT TO DO IN EMERGENCIES 401 vehicle. The rear hook will be located on the driver’s side of the vehicle. NOTE: For off-road recovery, it is recommended to use both of the front tow hooks to minimize the risk of damage to the vehicle. CAUTION! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. WARNING! Stand clear of vehicles when pulling with tow hooks.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment – 3.7L . . . . . . . . . . . . . . 406 䡵 Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . 413 䡵 Engine Compartment – 4.7L . . . . . . . . . . . . . . 407 䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . 413 䡵 Engine Compartment – 5.7L . . . . . . . . . . . . . . 408 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 414 䡵 Engine Compartment – 3.0L Diesel . . . . . . . . . 409 ▫ Engine Air Cleaner Filter . . . .
404 MAINTAINING YOUR VEHICLE ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . 422 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . 424 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . 430 ▫ Front/Rear Axle Fluid . . . . . . . . . . . . . . . . . 431 ▫ Transfer Case . . . . . . . . . . . . . . . . . . . . . . . 432 ▫ Automatic Transmission . . . . . . . . . . . . . . . 433 ▫ Maintenance After Off-Road Driving . . . . . . 436 ▫ Appearance Care And Protection From Corrosion . .
MAINTAINING YOUR VEHICLE 405 䡵 Fluids And Capacities . . . . . . . . . . . . . . . . . . 456 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458 䡵 Fluids, Lubricants, And Genuine Parts . . . . . . . 458 ▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . .
406 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT – 3.
MAINTAINING YOUR VEHICLE 407 ENGINE COMPARTMENT – 4.
408 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT – 5.
MAINTAINING YOUR VEHICLE 409 ENGINE COMPARTMENT – 3.
410 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 411 manual). Tighten the gas cap until a ⬙clicking⬙ sound is heard. This is an indication that the gas cap is properly tightened. The message will remain displayed until the vehicle diagnostic system can retest the fuel system. The test will perform the next time the vehicle is started, if the vehicle was keyed off above 40°F (4°C) outside temperature and the following vehicle start is above 40°F (4°C) outside temperature.
412 MAINTAINING YOUR VEHICLE Your vehicle has a simple ignition key-actuated test, which you can use prior to going to the test station. To check if your vehicle’s OBD II system is ready, you must do the following: 1. Insert your ignition key into the ignition switch. 2. Turn the ignition to the ON position, but do not crank or start the engine. 3. If you crank or start the engine, you will have to start this test over. 4.
MAINTAINING YOUR VEHICLE 413 before going to the I/M station. The I/M station can fail your vehicle because the MIL is on with the engine running. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. REPLACEMENT PARTS Use of genuine MOPAR威 parts for normal/scheduled maintenance and repairs is highly recommended to ensure the designed performance.
414 MAINTAINING YOUR VEHICLE operate satisfactorily without periodic maintenance. However, if a malfunction of these items does occur, it could adversely affect the engine or vehicle performance. These items should be inspected if a malfunction is observed or suspected. Engine Oil Checking Oil Level To assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop.
MAINTAINING YOUR VEHICLE 415 3.0L Diesel Engine Only Anytime the oil is drained and filled it is very important to wait 15 minutes before starting the engine. Engine Oil Selection — Gasoline Engines For best performance and maximum protection for all engines under all types of operating conditions, the manufacturer recommends engine oils that are API Certified and meet the requirements of Chrysler Material Standard MS-6395.
416 MAINTAINING YOUR VEHICLE Engine Oil Viscosity (3.7L/4.7L/5.7L Engines) SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your vehicle. For information on engine oil filler cap location, refer to “Engine Compartment” in this section.
MAINTAINING YOUR VEHICLE 417 The engine oil filler cap also shows the recommended engine oil viscosity for your vehicle. For information on engine oil filler cap location, refer to “Engine Compartment” in this section. Synthetic Engine Oils You may use synthetic engine oils if the recommended oil quality requirements are met, and the recommended maintenance intervals for oil and filter changes are followed. indiscriminately discarded, can present a problem to the environment.
418 MAINTAINING YOUR VEHICLE WARNING! The air induction system (air cleaner, hoses, etc) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air induction system (air cleaner, hoses, etc.) removed. Failure to do so can result in serious personal injury.
MAINTAINING YOUR VEHICLE 419 WARNING! (Continued) • Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling. CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post, and the negative cable is attached to the negative post. Battery posts are marked (+) positive and (-) negative and identified on the battery case.
420 MAINTAINING YOUR VEHICLE WARNING! (Continued) • The air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced repairman. NOTE: Use only manufacturer approved A/C System Sealers, Stop Leak Products, Seal Conditioners, Compressor Oil, and Refrigerants.
MAINTAINING YOUR VEHICLE 421 Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild nonabrasive cleaner to remove accumulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield. Avoid using the wiper blades to wipe frost or ice from the windshield.
422 MAINTAINING YOUR VEHICLE WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
MAINTAINING YOUR VEHICLE 423 Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. CAUTION! A hot exhaust system can start a fire if you park over materials that can burn.
424 MAINTAINING YOUR VEHICLE To minimize the possibility of catalytic converter damage: • Do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idle or malfunctioning operating conditions.
MAINTAINING YOUR VEHICLE 425 accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiator. Inspect the entire system for leaks.
426 MAINTAINING YOUR VEHICLE CAUTION! Mixing of engine coolant (antifreeze), other than the specified HOAT engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. If a non-HOAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with the specified engine coolant (antifreeze) as soon as possible. Do not use water alone or alcohol based engine coolant (antifreeze) products.
MAINTAINING YOUR VEHICLE 427 • Mix a minimum solution of 50% HOAT engine coolant (antifreeze) and distilled water. Use higher concentrations (not to exceed 70%) if temperatures below -34°F (-37°C) are anticipated. NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and will require more frequent engine coolant (antifreeze) changes.
428 MAINTAINING YOUR VEHICLE WARNING! • The warning words DO NOT OPEN HOT on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
MAINTAINING YOUR VEHICLE 429 of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember NOTE: When the vehicle is stopped after a few miles (kilometers) of operation, you may observe vapor coming from the front of the engine compartment.
430 MAINTAINING YOUR VEHICLE • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory cooling performance, poor gas mileage, and increased emissions.
MAINTAINING YOUR VEHICLE 431 With disc brakes, the fluid level can be expected to fall as the brake linings wear. However, an unexpected drop in fluid level may be caused by a leak and a system check should be conducted. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. Use only brake fluid that has been in a tightly-closed container to avoid contamination from foreign matter or moisture.
432 MAINTAINING YOUR VEHICLE Selection of Lubricant Use only the manufacturer’s recommended fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for correct fluid type. Transfer Case Fluid Level Check Inspect the transfer case for fluid leaks. If a fluid leak is found, the transfer case fluid level can be checked by removing the filler plug located on the back side of the transfer case.
MAINTAINING YOUR VEHICLE 433 Automatic Transmission Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission performance. Use only the manufacturer’s recommended transmission fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid.
434 MAINTAINING YOUR VEHICLE Fluid Level Check (3.7L and 3.0L Diesel Engine) Regular fluid level checks are not required. For this reason, the dipstick is omitted. If you notice fluid loss or shift lever malfunction, have your authorized dealer check the transmission fluid level. CAUTION! • Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder.
MAINTAINING YOUR VEHICLE 435 2. The vehicle must be on level ground. 3. Fully apply the parking brake, and press the brake pedal. 4. Place the shift lever momentarily in each gear position ending with the lever in PARK. 5. Remove the dipstick, wipe it clean and reinsert it until seated. 6. Remove the dipstick again, and note the fluid level on both sides. The fluid level should be between the “HOT” (upper) reference holes on the dipstick at normal operating temperature.
436 MAINTAINING YOUR VEHICLE To prevent dirt and water from entering the transmission after checking or replenishing fluid, make certain that the dipstick cap is properly reseated. It is normal for the dipstick cap to spring back slightly from its fully seated position, as long as its seal remains engaged in the dipstick tube. Service Manual.
MAINTAINING YOUR VEHICLE 437 passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.
438 MAINTAINING YOUR VEHICLE CAUTION! • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month.
MAINTAINING YOUR VEHICLE 439 Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome-plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil, use MOPAR威 Wheel Cleaner or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush or metal polishes. Only MOPAR威 cleaners are recommended. Do not use oven cleaner.
440 MAINTAINING YOUR VEHICLE WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas, they may cause respiratory harm. Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch-resistant as glass and therefore different lens cleaning procedures must be followed.
MAINTAINING YOUR VEHICLE 441 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use MOPAR威 Total Clean, a mild soap solution, or lukewarm water. Do not remove the belts from the vehicle to wash them. Replace the belts if they appear frayed or worn or if the buckles do not work properly. Fuse Panel Dry with a soft tissue.
442 MAINTAINING YOUR VEHICLE Cavity 3 4 5 6 7 8 9 Cartridge Mini-Fuse Fuse 10 Amp Red 20 Amp Yellow 10 Amp Red Spare (B+) 20 Amp Yellow Spare (B+) 20 Amp Yellow Description Htd Mirror (EBL) Cavity 10 Rr Pwr Out (B+) Rr HVAC (R/O) (Commander Only) Door Locks (B+) Pwr Outlet (B+) 11 12 13 Cartridge Mini-Fuse Description Fuse 10 Amp Final Drive Control Red Module (FDCM), Heater Ventilation/ Air Conditioning (HVAC), Rear Heated Seat Switch, O/H, Heater Ventilation/ Air Conditioning (HVAC) Relay, Rear P
MAINTAINING YOUR VEHICLE 443 Cavity 14 15 16 17 19 20 Cartridge Mini-Fuse Fuse 20 Amp Yellow 10 Amp Red 10 Amp Red 15 Amp Blue Spare (R/S) 10 Amp Red Description Cigar Ltr (R/A) Tire Pressure Transponders (R/O) Upper & Lower Switch Bank, Diag.
444 MAINTAINING YOUR VEHICLE Underhood Fuses (Power Distribution Center) Power Distribution Center Cav- Cartridge Mini-Fuse Description ity Fuse 1 50 Amp PTC Heater 1 (Diesel Red Only) Cav- Cartridge Mini-Fuse Description ity Fuse 2 40 Amp HID Headlamps Green 3 50 Amp PTC Heater 2 (Diesel Red Only) 4 30 Amp Power Outlets Pink 5 50 Amp PTC Heater 3 (Diesel Red Only) 6 30 Amp Cig Lighter, Trail Tow Pink Batt 7 40 Amp Power Liftgate (ComGreen mander Only) 8 40 Amp Starter, JB Power Green 9 20 Amp Front Pow
MAINTAINING YOUR VEHICLE 445 Cav- Cartridge Mini-Fuse Description ity Fuse 10 — Spare 11 40 Amp HVAC Blower Green 12 30 Amp Rear Wiper, Ign R/O Pink 13 40 Amp Rear Window DeGreen froster (EBL)/Heated Mirror 14 30 Amp Rear HVAC (If Pink Equipped) 15 — Spare 16 50 Amp ASD Red 17 30 Amp ABS Pump Pink Cav- Cartridge Mini-Fuse Description ity Fuse 18 40 Amp Accessory Delay, Seats Green 19 40 Amp JB Power Green 20 30 Amp Wiper Motor Pink 21 20 Amp Fuel Pump Yellow 22 20 Amp TCM, A/C Clutch Yellow 23 25 Amp Powe
446 MAINTAINING YOUR VEHICLE Cavity 26 27 28 29 30 31 32 33 Cartridge Mini-Fuse Description Fuse 15 Amp Brake Lamps Blue 20 Amp HD Washer (If Yellow Equipped) (Export Only) 30 Amp ABS Valves Green 20 Amp PCM Batt (Gasoline Yellow Only) — Spare — Spare 15 Amp Powertrain Control Blue Module (Diesel Only) 20 Amp Final Drive Control Yellow Module (FDCM) E-Diff Cavity 34 35 36 37 38 39 40 41 42 Cartridge Mini-Fuse Fuse — 20 Amp Yellow — 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 25 Amp Natural 20 Amp Yellow
MAINTAINING YOUR VEHICLE 447 Cavity 43 44 Cartridge Mini-Fuse Description Fuse 25 Amp Coils, Actuators Natural — Spare Underhood Fuses (Integrated Power Module) Cavity 8 9 10 12 13 14 15 16 Integrated Power Module Cartridge Mini-Fuse Fuse 10 Amp Red 10 Amp Red 10 Amp Red 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow Description Lt Park Lamps Trailer-Tow Park Lamps Rt Park Lamps Front Control Module (FCM) Batt #4 Front Control Module (FCM) Batt #2 Adjustable Pedal Ft Fog Lamps
448 MAINTAINING YOUR VEHICLE Cavity 17 18 19 20 21 22 23 27 Cartridge Mini-Fuse Fuse 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 30 Amp Pink 50 Amp Red 15 Amp Blue Description Rear Fog Lamps (Export Only) Front Control Module (FCM) Batt #1 Lt Trailer-Tow Stop/ Turn Front Control Module (FCM) Batt #3 Rt Trailer-Tow Stop/ Turn Final Drive Control Module (FDCM) MOD Radiator Fan Ignition Off Draw (IOD) #1 Cavity 28 29 30 Cartridge Mini-Fuse Fuse 20 Amp Yellow 10 Amp Red 10 Amp Re
MAINTAINING YOUR VEHICLE 449 air conditioning system at idle for about five minutes in the fresh air and high blower setting. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. REPLACEMENT BULBS Interior Lights Bulb Type Glove Box Light . . . . . . . . . . . . . . . . . . . . . . . . . 194 Grab Handle Light . . . . . . . . . . . . . . . . L002825W5W Overhead Console Reading Lights . . . . . . . . . . VT4976 Rear Cargo Light . . .
450 MAINTAINING YOUR VEHICLE BULB REPLACEMENT High Intensity Discharge Headlights (HID) — If Equipped The headlights are a type of high voltage discharge tube. High voltage can remain in the circuit even with the headlight switch off and the key removed. Because of this, you should not attempt to service a headlight bulb yourself. If a headlight bulb fails, take your vehicle to an authorized dealer for service.
MAINTAINING YOUR VEHICLE 451 Headlight 1. Open the hood. 2. Turn the low or high beam bulb one–quarter turn counterclockwise to remove from housing. 1 — High Beam Bulb 2 — Low Beam Bulb 3 — Turn Signal Bulb 3. Disconnect the electrical connector and replace the bulb.
452 MAINTAINING YOUR VEHICLE CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front Turn Signal 1. Open the hood. 2. Turn the turn signal bulb one–quarter turn counterclockwise to remove from housing. 1 — High Beam Bulb 2 — Low Beam Bulb 3 — Turn Signal Bulb 3. Disconnect the electrical connector and replace the bulb.
MAINTAINING YOUR VEHICLE 453 CAUTION! CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front Fog Light 1. Reach behind the front fascia from under the vehicle. 2.
454 MAINTAINING YOUR VEHICLE Rear Tail, Stop, Turn Signal, And Backup Lights 1. Raise the liftgate. 2. Remove the two Torx fasteners. 1 — Tail/Stop Light Bulb 2 — Tail/Turn Signal Bulb 3 — Back-Up Light Bulb 4. Pull the bulb to remove it from the socket. 3. Squeeze the socket assembly tabs to remove it from the housing. 5. Replace the bulb, reinstall the socket, and reattach the light assembly.
MAINTAINING YOUR VEHICLE 455 Center High-Mounted Stop Light (CHMSL) 1. Remove the two screws securing the CHMSL. 2. Twist the bulb socket to remove from the CHMSL housing. 3. Pull the bulb out of the socket. 4. Replace the bulb, reinstall the socket and reattach the CHMSL.
456 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel (Approximate) 3.7/4.7/5.7L Gasoline Engines 3.0L Diesel Engine Engine Oil with Filter 3.7 Liter Engine (SAE 5W-20, API Certified) 4.7 Liter Engine (SAE 5W-20, API Certified) 5.7 Liter Engine (SAE 5W-20, API Certified) 3.0 Liter Diesel Engine (SAE 5W-30 Synthetic, API Certified Low Ash) Cooling System * 3.7 Liter and 4.7L Engine (MOPAR威 Engine Coolant/Antifreeze 5 Year/100,000 Mile Formula) — Without Rear Heat 3.7 Liter and 4.
MAINTAINING YOUR VEHICLE 457 5.7 Liter Engine (MOPAR威 Engine Coolant/Antifreeze 5 Year/100,000 Mile Formula) — With Rear Heat 3.0 Liter Diesel Engine (MOPAR威 Antifreeze/Engine Coolant 5 Year/100,000 Mile Formula) — Without Rear Heat 3.0 Liter Diesel Engine (MOPAR威 Antifreeze/Engine Coolant 5 Year/100,000 Mile Formula) — With Rear Heat * Includes heater and coolant recovery bottle filled to MAX level. 16.7 Quarts 15.8 Liters 13.9 Quarts 13.2 Liters 15.3 Quarts 14.
458 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) Engine Oil (3.7L/4.7L/5.7L Engines) Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to your engine oil filler cap for correct SAE grade. Engine Oil (3.
MAINTAINING YOUR VEHICLE 459 Component Fuel Selection (3.7L and 4.7L Engine) Fuel Selection (5.7L Engine) Fuel Selection (3.0L Diesel Engine) Fluid, Lubricant, or Genuine Part 87 Octane 87 Octane Acceptable - 89 Octane Recommended Use good quality diesel fuel from a reputable supplier in your vehicle.
460 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Transfer Case (NV140 Single Speed Only) Transfer Case (NV245 Two Speed Only) Axle Differential (Front-Rear) Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4 Automatic Transmission Fluid MOPAR威 ATF+4 Automatic Transmission Fluid MOPAR威 NV 247/245 Transfer Case Lubricant MOPAR威 Synthetic Gear & Axle Lubricant SAE 75W-140 (API-GL5) or equivalent with friction modifier additive.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emissions Control System Maintenance . . . . . . 462 ▫ Maintenance Schedule — Gasoline Engine . . 462 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . 462 ▫ Maintenance Schedule — Diesel Engine . . . .
M A I N T E N A N C E 462 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 463 M if it has been 6 months since your last oil change even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or 6 months, whichever comes first. A I N T E N • Check the windshield washer solvent and add if A N required.
M A I N T E N A N C E S C H E D U L E S 8 464 MAINTENANCE SCHEDULES At Each Oil Change Required Maintenance Intervals • Change the engine oil filter. NOTE: ** Vehicles built with the 4.7L engine are equipped with sixteen spark plugs, one set is located on the top of the engine under the coils and the second set is located on the side of the engine. • Inspect the brake hoses and lines. CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle.
MAINTENANCE SCHEDULES 465 M 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings, replace if necessary. ❏ Inspect the CV joints.
M 466 MAINTENANCE SCHEDULES A I N 18,000 Miles (30,000 km) or T 18 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ Inspect the front and rear axle fluid, S C H E D U L E S change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter.
MAINTENANCE SCHEDULES 467 M 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule 42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings, replace if necessary.
M 468 MAINTENANCE SCHEDULES A I N 54,000 Miles (90,000 km) or T 54 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ Inspect the front and rear axle fluid, S C H E D U L E S 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires.
MAINTENANCE SCHEDULES 469 M 66,000 Miles (110,000 km) or 66 Months Maintenance Service Schedule 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary. ❏ Inspect the CV joints. ❏ Inspect exhaust system.
M 470 MAINTENANCE SCHEDULES A I N 78,000 Miles (130,000 km) or T 78 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary.
MAINTENANCE SCHEDULES 471 M 90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the top row of spark plugs (4.7L Engine). Replace the spark plugs (3.7L and 5.7L Engines). Inspect and replace PCV valve if necessary. † Adjust parking brake on vehicles equipped with four-wheel disc brakes. Inspect the transfer case fluid.
M 472 MAINTENANCE SCHEDULES A I N 102,000 Miles (170,000 km) or T 102 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ Replace the ignition cables (4.7L S C H E D U L E S Engine). ❏ Replace the side row of spark plugs (4.7L Engine). ❏ Flush and replace the engine coolant if not done at 60 months.
MAINTENANCE SCHEDULES 473 M 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the ignition cables (3.7L Engine). Replace the top row of spark plugs (4.7L Engine). Replace the spark plugs (3.7L and 5.7L Engines). Adjust parking brake on vehicles equipped with four-wheel disc brakes. Inspect the brake linings; replace if necessary. Inspect the CV joints.
M 474 MAINTENANCE SCHEDULES A I N 126,000 Miles (210,000 km) or T 126 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ Inspect the front and rear axle fluid, S C H E D U L E S change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
MAINTENANCE SCHEDULES 475 M 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary. ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. ❏ Inspect the CV joints.
M A I N T E N A N C E S C H E D U L E S 8 476 MAINTENANCE SCHEDULES † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
MAINTENANCE SCHEDULES 477 M A • Check the windshield washer solvent and add if required. Once a Month • Check tire pressure and look for unusual wear or damage. • Inspect the battery and clean and tighten the terminals as required. • Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering and add as needed. • Check all lights and other electrical items for correct operation. At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines.
M 478 MAINTENANCE SCHEDULES A I N 6,250 Miles (10,000 km) or T 6 Months Maintenance Service E N Schedule A ❏ Rotate tires. N C E S C H E D U L E S 12,500 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ Inspect the brake linings, replace if necessary. ❏ Inspect exhaust system.
MAINTENANCE SCHEDULES 479 M 18,750 Miles (30,000 km) or 18 Months Maintenance Service Schedule 25,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Rotate tires. ❏ Inspect the front and rear axle fluid. Change if using your vehicle for police, taxi, fleet, off-road, or frequent trailer towing. ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the fuel filter/water separator unit.
M 480 MAINTENANCE SCHEDULES A I N 31,250 Miles (50,000 km) or T 30 Months Maintenance E N Service Schedule A ❏ Rotate tires. N C E S C H E D U L E S 37,500 Miles (60,000 km) or 36 Months Maintenance Service Schedule 43,750 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary.
MAINTENANCE SCHEDULES 481 M 50,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the fuel filter/water separator unit. Inspect the front suspension, tie rod ends and boot seals, replace if necessary. Inspect the brake linings, replace if necessary. Inspect exhaust system. Inspect the CV joints. Inspect the transfer case fluid.
M 482 MAINTENANCE SCHEDULES A I N 62,500 Miles (100,000 km) or 60 Months Maintenance Service T Schedule E ❏ Change the engine oil and engine oil filter. N A ❏ Rotate tires. N ❏ If you are using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. C E ❏ Inspect the brake linings, replace if necessary. S C H E D U L E S 68,750 Miles (110,000 km) or 66 Months Maintenance Service Schedule ❏ Rotate tires.
MAINTENANCE SCHEDULES 483 M 75,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the fuel filter/water separator unit. Inspect the front suspension, tie rod ends and boot seals, replace if necessary. Inspect the brake linings, replace if necessary. Inspect the front and rear axle fluid.
M 484 MAINTENANCE SCHEDULES A I N 87,500 Miles (140,000 km) or T 84 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ If you are using your vehicle for any of S C H E D U L E S the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. ❏ Inspect the brake linings, replace if necessary. 93,750 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Rotate tires.
MAINTENANCE SCHEDULES 485 M 100,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the fuel filter/water separator unit. Inspect the front suspension, tie rod ends and boot seals, replace if necessary. Inspect the brake linings, replace if necessary. Inspect exhaust system. Inspect the CV joints. Inspect the transfer case fluid.
M 486 MAINTENANCE SCHEDULES A I N WARNING! T E You can be badly injured working on or around a N motor vehicle. Do only that service work for which A you have the knowledge and the right equipment. If N C you have any doubt about your ability to perform a E service job, take your vehicle to a competent meS C H E D U L E S 8 chanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 489 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 491 ▫ Prepare For The Appointment . . . . . . . . . . . 489 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 491 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 489 䡵 Warranty Information (U.S. Vehicles Only) . . . .
488 IF YOU NEED CONSUMER ASSISTANCE 䡵 Publication Order Forms . . . . . . . . . . . . . . . . 493 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 495 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 494 ▫ Temperature Grades . . . . . . . . . . . . . . . . . . 495 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 489 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
490 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealership. They want to know if you need assistance. • If an authorized dealership is unable to resolve the concern, you may contact the manufacturer’s customer center.
IF YOU NEED CONSUMER ASSISTANCE 491 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
492 IF YOU NEED CONSUMER ASSISTANCE the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns. WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm.
IF YOU NEED CONSUMER ASSISTANCE 493 To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov. PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below.
494 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-bystep troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.
IF YOU NEED CONSUMER ASSISTANCE 495 Treadwear The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
496 IF YOU NEED CONSUMER ASSISTANCE Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel, than the minimum required by law. WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
INDEX 10
498 INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . 309 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 364 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 143 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 417 Air Conditioner Maintenance . . . . . . . . . . . . . . . 419 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 264 Air Conditioning, Operating Tips . . . . . . . . . . . . 271 Air Conditioning Refrigerant . . . . . . . . . . . .
INDEX 499 Torque Converter . . . . . . . . . . . . . . . Autostick . . . . . . . . . . . . . . . . . . . . . . Auxiliary Electrical Outlet (Power Outlet) Auxiliary Power Outlet . . . . . . . . . . . . ... ... .. ... . . . . . . . . . . . . . . . . 294 290 163 163 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 418 Emergency Starting . . . . . . . . . . . . . . . . . . . . . 398 Keyless Transmitter Replacement (RKE) . . . . . . . 25 Saving Feature (Protection) . . . . . . . . .
500 INDEX Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 Luggage Carrier . . . . . . . . . . . . . . . . . . . . . . . 174 Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 Cargo Load Floor . . . . . . . . . . . . . . . . . . . . . . . . 171 Cargo Tie-Downs . . . . . . . . . . . . . . . . . . . . . . . . 170 Cargo (Vehicle Loading) . . . . . . . . . . . . . . . . . . . 367 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 501 Drain, Flush, and Refill . . . . . . Inspection . . . . . . . . . . . . . . . Points to Remember . . . . . . . . Pressure Cap . . . . . . . . . . . . . Radiator Cap . . . . . . . . . . . . . Selection of Coolant (Antifreeze) Cruise Light . . . . . . . . . . . . . . . Cupholders . . . . . . . . . . . . . . . . Customer Assistance . . . . . . . . . . . . . . . . . . . . . 425 . . . . . . . . . . . . 424 . . . . . . . . . . . . 429 . . . . . . . . . . . . 427 . . . . . . . . . . . . 427 . . . . . .
502 INDEX Electrical Outlet, Auxiliary (Power Outlet) . . . . . . 163 Electronic Brake Control System . . . . . . . . . . . . . 312 Anti-Lock Brake System . . . . . . . . . . . . . . . . . 312 Brake Assist System . . . . . . . . . . . . . . . . . . . . 313 Electronic Roll Mitigation . . . . . . . . . . . . . . . . 314 Electronic Stability Program . . . . . . . . . . . . . . . 315 Traction Control System . . . . . . . . . . . . . . . . . 313 Electronic Roll Mitigation (ERM) . . . . . . . . . . . . .
INDEX 503 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . 390 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280 Temperature Gauge . . . . . . . . . . . . . . . . . . . . 189 Engine Oil Viscosity . . . . . . . . . . . . . . . . . . . . . . 416 Engine Oil Viscosity Chart . . . . . . . . . . . . . . . . . 416 Enhanced Accident Response Feature . . . . . . . . . . 54 Entry System, Illuminated . . . . . . . . . . . . . . . . . . 21 Event Data Recorder . . . . . . . . . . . .
504 INDEX Fog Lights . . . . . . . . . . . . . . . . . . . . . . . 135,192,453 Folding Rear Seat . . . . . . . . . . . . . . . . . . . . . . . . 122 Four Wheel Drive . . . . . . . . . . . . . . . . . . . . . . . 296 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 296 Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296 Four Wheel Drive Operation . . . . . . . . . . . . . . . . 296 Four-Way Hazard Flasher . . . . . . . . . . . . . . . . . . 390 Freeing A Stuck Vehicle . . .
INDEX 505 Gross Vehicle Weight Rating . . . . . . . . . . . . . 367,369 GVWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367 Hands-Free Phone (uconnect) . . . . . . . . . . . . . . . . 82 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . . 390 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . 118 Head Rests . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . 130,450 Bulb Replacement . . . . . .
506 INDEX Interior Appearance Care . . . . . . . . . . . . . . . . . . 439 Interior Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . 441 Interior Lighting . . . . . . . . . . . . . . . . . . . . . . . . 137 Interior Lights . . . . . . . . . . . . . . . . . . . . . . . 134,137 Intermittent Wipers (Delay Wipers) . . . . . . . . . . . 140 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Inverter, Power . . . . . . . . . . . . . . . . . . . . . . . . . 165 Jack Location . . . .
INDEX 507 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 450 Cargo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 Center Mounted Stop . . . . . . . . . . . . . . . . . . . 455 Cruise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 Daytime Running . . . . . . . . . . . . . . . . . . . . . . 133 Dimmer Switch, Headlight . . . . . . . . . . . . . 130,137 Electronic Stability Program (ESP) Indicator . . . 325 Electronic Throttle Control Warning . . . . . . . . .
508 INDEX Traction Control . . . . . . . . . . . . . . . . . . . . . . . 325 Turn Signal . . . . . . . . . . . . . . . . 71,130,136,452,454 Vanity Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192 Load Floor, Cargo . . . . . . . . . . . . . . . . . . . . . . . 171 Loading Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 367 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331 Locks . . . . . . . .
INDEX 509 Mopar Parts . . . . . . . . . . . . . . . . . . . . . . . . . 413,492 Multi-Function Control Lever . . . . . . . . . . . . . . . 130 New Vehicle Break-In Period . . . . . . . . . . . . . . . . 68 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . . . 36 Octane Rating, Gasoline (Fuel) . . . . . . . . . . . . 355,356 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . 190,191 Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
510 INDEX Park Sense System, Rear . . . . . . . . . . . . . . . . . . . 147 Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . 308 Passing Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Pedals, Adjustable . . . . . . . . . . . . . . . . . . . . . . . 143 Personal Settings . . . . . . . . . . . . . . . . . . . . . . . . 202 Pets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Pets, Transporting . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 511 Rear Heated Seats . . . . . . . . . . . . . . . . . . . . . . . 120 Rear Park Sense System . . . . . . . . . . . . . . . . . . . 147 Rear Seat, Folding . . . . . . . . . . . . . . . . . . . . . . . 122 Rear Window Defroster . . . . . . . . . . . . . . . . . . . 173 Rear Window Features . . . . . . . . . . . . . . . . . . . . 172 Rear Wiper/Washer . . . . . . . . . . . . . . . . . . . . . . 172 Rearview Mirrors . . . . . . . . . . . . . . . . . . . . . . . . 78 Reclining Front Seats . . . . . . .
512 INDEX Safety Information, Tire . . . . . . . . . . . . . . . . . . . 326 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Satellite Radio Antenna . . . . . . . . . . . . . . . . . . . 253 Satellite Radio (uconnect studios) . . . . . . . . . . 252,257 Schedule, Maintenance . . . . . . . . . . . . . . . . . 462,476 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . . . 44 Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 513 Service Manuals . . . . . . . . . . . . . . . . . . . . . . . . 493 Setting the Clock . . . . . . . . . . . . . . . . 209,223,227,236 Settings, Personal . . . . . . . . . . . . . . . . . . . . . . . . 202 Shift Lock Manual Override . . . . . . . . . . . . . . . . 287 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286 Automatic Transmission . . . . . . . . . . . . . . . . . 286 Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Signals, Turn . . . . . .
514 INDEX Sunglasses Storage . . . . . . . . . . . . . . . . . . . . . . . 154 Supplemental Restraint System - Airbag . . . . . . . . 46 Sway Control, Trailer . . . . . . . . . . . . . . . . . . . . . 320 Synthetic Engine Oil . . . . . . . . . . . . . . . . . . . . . . 417 System, Remote Starting . . . . . . . . . . . . . . . . . . . . 27 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 Telescoping Steering Column . . . . . . . . . . . . . . .
INDEX 515 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326 Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327 Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 392 Spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . 340 Wheel Mounting . . . . . . . . . . . . . . . . . . . . . . 397 Tongue Weight/Trailer Weight . . . . . . . . . . . . . . 375 Torque Converter Clutch . . . .
516 INDEX Transmitter, Remote Keyless Entry (RKE) . . . . . . . . 21 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . 340 Turn Signals . . . . . . . . . . . . . . . . . . . 136,185,452,454 UCI Connector . . . . . . . . . . . . . . . . . . . . . . . . . 247 uconnect (Hands-Free Phone) . . . . . . . . . . . . . . . . 82 Underhood Fuses . . . . . . . . . . . . . . . . . . . . . 444,447 Uniform Tire Quality Grades . . . . . . . . . . . . . . . . 494 Universal Consumer Interface (UCI) Connector . .
INDEX 517 Windshield Defroster . . . . . . . . . . . . . . . . 71,263,269 Windshield Washers . . . . . . . . . . . . . . . . . . . . . . 139 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 421 Windshield Wiper Blades . . . . . . . . . . . . . . . . . . 421 Windshield Wipers . . . . . . . . . . . . . . . . . . . . . . . 139 Wipers, Intermittent . . . . . . . . . . . . . . . . . . . . . . 140 Wipers, Rain Sensitive . . . . . . . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
2009 GRAND CHEROKEE GRAND CHEROKEE 2009 owner’s manual Chrysler LLC 81-326-0954 150920 GrCherokee.indd 1 Second Edition Printed in U.S.A.
