2010 OWNE R ’ S MANUAL Grand Cherokee SRT8
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 7 䡵 Rollover Warning . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number .............. 7 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 5 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . .
4 INTRODUCTION INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle.
INTRODUCTION 5 control. Failure to operate this vehicle safely may result belts could cut the highway death toll by 10,000 or more in an accident, rollover of the vehicle, and severe or fatal each year and could reduce disabling injuries by two million annually. In a rollover crash, an unbelted person injury. Drive carefully. is significantly more likely to die than a person wearing a seat belt. Always buckle up.
6 INTRODUCTION
INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 䡵 Vehicle Security Alarm — If Equipped . . . . . . . . 17 ▫ Wireless Ignition Node (WIN) . . . . . . . . . . . . 12 ▫ Rearming The System . . . . . . . . . . . . . . . . . . 17 ▫ Key FOB . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 ▫ To Set The Alarm . . . . . . . . . . . . . . . . . . . . . 17 ▫ Removing Key FOB From Ignition . . . . . . . . . 13 ▫ To Disarm The System .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Remote Open Window Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 22 ▫ Programming Additional Transmitters . . . . . . 22 ▫ Transmitter Battery Replacement . . . . . . . . . . 22 ▫ General Information . . . . . . . . . . . . . . . . . . . 23 䡵 Remote Starting System — If Equipped . . . . . . . 24 ▫ How To Use Remote Start . . . . . . . . . . . . . . . 24 䡵 Door Locks .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Seat Belts And Pregnant Women . . . . . . . . . . 44 䡵 Engine Break-In Recommendations . . . . . . . . . . 70 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . 44 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 ▫ Supplemental Restraint Systems (SRS) — Airbags . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 ▫ Advanced Front Airbag Features . . . . . . . . . . 47 ▫ Airbag Deployment Sensors And Controls . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the Key Fob into the ignition switch with either side up. Wireless Ignition Node (WIN) The Wireless Ignition Node (WIN) operates similar to an ignition switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead. The emergency key is also for locking the glove box. You can keep the emergency key with you when valet parking.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • If you try to remove the Key Fob before you place the shift lever in PARK, it may become trapped temporarily in the ignition switch. If this occurs, rotate the key to the right slightly, then remove the Key Fob as described. If a malfunction occurs, the system will trap the key in the ignition switch to warn you that this safety feature is inoperable. The engine can be started and stopped, but the Key Fob cannot be removed until you obtain service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 system will shut the engine off in two seconds if an Key-In-Ignition Reminder Opening the driver’s door when the Key Fob is in the invalid Key Fob is used to start the engine. ignition and the ignition switch position is OFF or ACC, After turning the ignition switch to the ON position, the sounds a signal to remind you to remove the Key Fob. Vehicle Security Light will turn on for three seconds for a NOTE: The Key-In-Ignition reminder only sounds bulb check.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The Sentry Key威 Immobilizer system is not compatible with aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). Keep the PIN in a secure location. This number is required for authorized dealer replacement of Key Fobs.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 park lamps and/or turn signals will flash for an addiGeneral Information The Sentry Key威 system complies with FCC rules Part 15 tional 15 minutes. and with RSS-210 of Industry Canada. Operation is NOTE: The Panic and Security alarms are quite differsubject to the following conditions: ent. Please take a moment to activate the Panic and the Security modes to hear the differences in the horn. In case • This device may not cause harmful interference.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Vehicle Security Light (located in the instrument cluster) will flash rapidly for about 16 seconds to signal that the Vehicle Security Alarm is arming. During this 16 second arming period, opening any door or the liftgate will cancel the arming. If the Vehicle Security Alarm successfully arms, the Vehicle Security Light will flash at a slower rate to indicate the alarm is set.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: None of the courtesy lights will operate if the dimmer control is in the “defeat” position (extreme downward position), unless the overhead map/reading lights are turned on manually. 2 REMOTE KEYLESS ENTRY (RKE) This system allows you to lock or unlock the doors and liftgate, or activate the panic alarm, from distances up to approximately 66 ft (20 m) using a hand-held Key Fob with RKE transmitter.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Information Center (EVIC)/Personal Settings Remote Key Unlock, Driver Door/All Doors First (Customer-Programmable Features)” in “UnderstandPress ing Your Instrument Panel” for further information. This feature lets you program the system to unlock either the driver’s door or all doors, on the first press of the Turn Headlights On with Remote Key Unlock UNLOCK button on the RKE transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sound Horn with Remote Key Lock This feature will cause the horn to chirp when the doors are locked with the RKE transmitter. This feature can be turned on or off. To change the current setting, proceed as follows: 21 WARNING! Driving with the flipper glass open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the flipper glass closed when you are operating the vehicle.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using the Panic Alarm To turn the Panic Alarm feature on or off, press and hold the PANIC button on the RKE transmitter for at least one second and release. When the Panic Alarm is on, the headlights and park lamps will flash, the horn will pulse on and off, and the interior lights will turn on. Transmitter Battery Replacement The recommended replacement battery is one CR2032 battery. NOTE: • Perchlorate Material — special handling may apply. See www.dtsc.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 3. Reposition the access door panel over the battery opening and snap into place. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. A weak battery in the RKE transmitter. The expected How to Use Remote Start All of the following conditions must be met before the life of the battery is a minimum of three years. engine will remote start: 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Monoxide (CO) which is odorless and colorless. Carbon Monoxide is poisonous and can cause serious injury or death when inhaled. • Keep Remote Keyless Entry (RKE) transmitters away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the key. Once inserted, the message “Turn To Run” NOTE: To avoid unintentional shutdowns, the system will flash in the EVIC until you turn the key to run. will disable the one time press of the REMOTE START button for two seconds after receiving a valid Remote DOOR LOCKS Start request.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 WARNING! (Continued) • When leaving the vehicle, always remove the key from the ignition and lock your vehicle. Do not leave unattended children in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal injuries and death. 2 Power Door Locks The power door lock switch is located on each front door panel. Press the switch to lock or unlock the doors.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The rear doors cannot be opened from inside the vehicle Personal Settings (Customer-Programmable Features)” in “Understanding Your Instrument Panel” for further until you pull up the lock plungers. information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the ON or ACCESSORY position. 2 Child Protection Door Lock WINDOWS Power Windows Power Window Switches The power window controls are located on the driver’s door trim panel.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto-Down Both the driver and front passenger window switches have an “Auto-Down” feature. Press the window switch past the first detent, release, and the window will go down automatically. To cancel the “Auto-Down” movement, operate the switch in either the up or down direction and release the switch. To stop the window from going all the way up during the Auto Up operation, push down on the switch briefly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Resetting the Auto Up Feature Should the Auto Up feature stop working, the window probably needs to be reset. To reset Auto Up: 2 Pull the window switch up and close the window completely, then pull and hold the switch for one second. Window Lockout Button The Window Lockout button on the driver’s door allows you to disable the window controls on the other doors. To disable the window controls on the other doors, press the Window Lockout button.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • The tailpipes may be hot and you could be seriously injured if you come into contact with them. Liftgate Flipper Glass The liftgate flipper glass is also unlocked when the liftgate is unlocked.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Once the liftgate flipper glass has been opened, connec- OCCUPANT RESTRAINTS tion to the rear window wiper is interrupted, preventing Some of the most important safety features in your activation of the rear wiper blade while the flipper glass vehicle are the restraint systems: is open.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Front seat belts incorporate pretensioners to enhance occupant protection by managing occupant energy during an impact event — if equipped If you will be carrying children too small for adult-sized seat belts, the seat belts or the Lower Anchors and Tether for CHildren (LATCH) feature also can be used to hold infant and child restraint systems. For more information on LATCH, see Lower Anchors and Tether for CHildren (LATCH).
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions in your vehicle have combination lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. 37 2. The seat belt latch plate is above the back of your seat.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A belt that is worn under your arm is very dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind you will not protect you from injury during a collision.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Position the shoulder belt on your chest so that it is 6. To release the belt, push the red button marked PRESS comfortable and not resting on your neck. The retractor on the buckle. The belt will automatically retract to its will withdraw any slack in the belt. stowed position. If necessary, slide the latch plate down the webbing to allow it to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front seating positions, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Press the release button to release the anchorage, and then move it up or down to the position that serves you best. 41 As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you will prefer a higher position.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • The belt and retractor assembly must be replaced if the seat belt assembly Automatic Locking Retractor (ALR) feature or any other seat belt function is not working properly when checked according to the procedures in the Service Manual. • Failure to replace the belt and retractor assembly could increase the risk of injury in collisions. Automatic Locking Retractors (ALR) Mode — If Equipped In this mode, the shoulder belt is automatically prelocked.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners — If Equipped The seat belts for both front seating positions may be equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Turn the ignition switch to the OFF position, and Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts buckle the driver’s seat belt. throughout their pregnancy. Keeping the mother safe is 2. Turn the ignition key to the ACC/ON position (do not the best way to keep the baby safe. start the engine), and wait for the Seat Belt Reminder Pregnant women should wear the lap part of the belt Light to turn off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions. Remove and store the extender when not needed. Supplemental Restraint Systems (SRS) — Airbags This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: These airbags are certified to the new Federal • regulations for Advanced Airbags. • The Advanced Front Airbags have a multistage inflator • design. This allows the airbag to have different rates of • inflation based on the severity and type of collision. This vehicle may also be equipped with Supplemental Side Airbag Inflatable Curtains (SABIC) to protect the driver, front, and rear passengers sitting next to a window.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Advanced Front Airbag Features The Advanced Front Airbag system has multistage driver and front passenger airbags. This system provides output appropriate to the severity and type of collision as determined by the Occupant Restraint Controller (ORC), which may receive information from the impact sensors at the front of the car. The first stage inflator is triggered immediately during an impact that requires airbag deployment.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped SABIC airbags offer side-impact and vehicle rollover protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each airbag features inflated chambers placed adjacent to the head of each outboard occupant that reduce the potential for side-impact head injuries. The curtains deploy downward, covering both windows on the impact side.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • Should a vehicle rollover occur, the pretensioners and/or SABIC airbags on both sides of the vehicle may deploy. • Airbag covers may not be obvious in the interior trim; but they will open during airbag deployment. The system includes sensors adjacent to both front and rear seat occupants that are calibrated to deploy the SABIC airbags during impacts that require airbag occupant protection.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Along with seat belts and pretensioners, Advanced Front Airbags work with the knee bolsters to provide improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occupant protection. secured in the rear seat in child restraints or beltpositioning booster seats. Older children who do not use child restraints or belt-positioning booster seats should ride properly buckled up in the rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Do not lean against the door. If your vehicle has side airbags, and deployment occurs, the side airbags will inflate forcefully into the space between you and the door. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided under ⬙If You Need Assistance⬙. WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ORC deploys the Advanced Front Airbags, SABIC air- The side airbags will not deploy in all side collisions. Side bags — if equipped, and front seat belt pretensioners — airbag deployment will depend on the severity and type if equipped, as required, depending on severity and type of collision. of impact.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC contains a backup power supply system that may deploy the airbags even if the battery loses power or it becomes disconnected prior to deployment. 53 WARNING! Ignoring the Airbag Warning Light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A quantity of non-toxic gas is generated to inflate the side curtain airbag. The inflating side curtain airbag pushes the outside edge of the headliner out of the way and covers the window.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front and Side Impact Sensors In front and side impacts, impact sensors aid the ORC in determining appropriate response to impact events. Additional sensors in the ORC determine the level of airbag deployment and provide verification.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the airbags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System 57 WARNING! (Continued) WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately. located on the inside of the fuse block cover for the proper airbag fuses. See your authorized dealer if the fuse is good.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 2. Under certain circumstances, EDR data may not be accessing the electronic data stored, unless ordered to download data by a court with legal jurisdiction (i.e., recorded (e.g., loss of battery power). pursuant to a warrant). A copy of the data will be In conjunction with other data gathered during a comprovided to the custodial entity upon request.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Requested by police under a legal warrant. Child Restraints Everyone in your vehicle needs to be buckled up all the 4. Otherwise required by law. time, including babies and children. Every state in the United States, and all Canadian provinces, require that Data parameters that are recorded: small children ride in proper restraint systems. This is the • Diagnostic trouble code(s) and warning light status for law, and you can be prosecuted for ignoring it.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size. 61 • The infant carrier is only used rearward-facing in the vehicle.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward-facing infant restraint should only be used in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 belt tight; however, any seat belt system will loosen • If the belt still cannot be tightened, or if pulling and with time, so check the belt occasionally and pull it pushing on the restraint loosens the belt, disconnect tight if necessary).
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg), and who are older than one year, can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg), and who are older than one year.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH — Child Seat Anchorage System (Lower Anchors and Tether for CHildren) Your vehicle’s rear seat is equipped with the child restraint anchorage system called LATCH. The LATCH system provides for the installation of the child restraint without using the vehicle’s seat belts, instead securing the child restraint using lower anchorages and upper tether straps from the child restraint to the vehicle structure. 65 strap kits or retro-fit kits.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you are installing LATCH-compatible child restraints in adjacent rear seating positions, you can use the LATCH anchors or the vehicle’s seat belt for the outboard position, but you must use the vehicle’s seat belt at the center position. If your child restraints are not LATCHcompatible, you can only install the child restraints using the vehicle’s seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 In addition, there are tether strap anchorages behind each means of adjusting the tension in the strap. Forwardrear seating position located on the back of the seat. facing toddler restraints and some rear-facing infant restraints will also be equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. To attach a child restraint tether strap: 2 Route the tether strap over the seatback and attach the hook to the tether anchor located on the back of the seat. For the outboard seating positions, route the tether over the head rests, and attach the hook to the tether anchor located on the back of the seat.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication of difficulty. SAFETY TIPS 71 WARNING! (Continued) • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Do not run the engine in a closed garage or in confined damaged, have a competent mechanic inspect the comareas any longer than needed to move your vehicle in or plete exhaust system and adjacent body areas for broken, out of the area. damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes If it is necessary to sit in a parked vehicle with the engine to seep into the passenger compartment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light The light should come on and remain on for six to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Defroster Check operation by selecting the defrost mode and place the blower control on high speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 䡵 Uconnect™ phone — If Equipped . . . . . . . . . . . 83 ▫ Automatic Dimming Mirror . . . . . . . . . . . . . . 80 䡵 Voice Command — If Equipped . . . . . . . . . . . . 83 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . 81 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 ▫ Outside Mirrors Folding Feature . . . . . . . . . .
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . . 87 ▫ Multifunction Lever . . . . . . . . . . . . . . . . . . 100 ▫ Front Heated Seats — If Equipped . . . . . . . . . 88 ▫ Headlights And Parking Lights . . . . . . . . . . 100 ▫ Rear Heated Seats — If Equipped . . . . . . . . . . 90 ▫ Automatic Headlights — If Equipped . . . . . . 101 ▫ 60/40 Split Rear Seat . . . . . . . . . . . . . . . . . . . 91 ▫ Headlights On Automatically With Wipers .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 ▫ Lane Change Assist . . . . . . . . . . . . . . . . . . . 106 䡵 Adjustable Pedals — If Equipped . . . . . . . . . . 114 ▫ High/Low Beam Switch . . . . . . . . . . . . . . . 106 䡵 Electronic Speed Control — If Equipped . . . . . 116 ▫ Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . 106 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . 116 ▫ Headlight Time Delay . . . . . . . . . . . . . . . . . 107 ▫ To Set a Desired Speed . . . .
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Cleaning Parksense威 . . . . . . . . . . . . . . . . . . 122 ▫ Using HomeLink威 . . . . . . . . . . . . . . . . . . . 133 ▫ System Usage Precautions . . . . . . . . . . . . . . 122 ▫ Reprogramming A Single HomeLink威 Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 䡵 Parkview威 Rear Back Up Camera — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 ▫ Turning Parkview威 On Or Off — With Navigation/Multimedia Radio . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . 137 ▫ Rear Storage Compartment . . . . . . . . . . . . . 144 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . 137 ▫ Retractable Cargo Area Cover — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 144 ▫ Ignition Off Operation . . . . . . . . . . . . . . . . . 137 ▫ Sunroof Fully Closed . . . . . . . . . . . . . . . . . . 137 䡵 Electrical Power Outlets . . . . . . . . . . . . . .
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Automatic Dimming Mirror This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will illuminate to indicate when the dimming feature is activated. Automatic Dimming Mirror CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors To receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. WARNING! Vehicles and other objects seen in the passenger-side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger-side mirror could cause you to collide with another vehicle or other objects.
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Outside Mirrors The power mirror switch is located on the driver’s door trim panel next to the power door lock switch. A rotary knob selects the left mirror, right mirror or off position. After selecting a mirror, move the knob in the same direction you want the mirror to move. Use the off (center) position to guard against accidentally moving a mirror position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Illuminated Vanity Mirrors — If Equipped Uconnect™ Phone — IF EQUIPPED To access an illuminated vanity mirror, flip down one of Refer to “Uconnect™ Phone” in the Uconnect™ User the sun visors. Manual located on the DVD for further details. Lift the cover to reveal the mirror. The light will turn on VOICE COMMAND — IF EQUIPPED automatically. Refer to “Voice Command” in the Uconnect™ Phone User Manual located on the DVD for further details.
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Be sure everyone in your vehicle is in a seat and using a seat belt properly. Front Manual Seat Adjustment Move the seat forward or rearward using the adjustment bar. Lift up on the bar located on the front of the seat near the floor. Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched. WARNING! Adjusting a seat while the vehicle is moving is dangerous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Manual Lumbar Support Adjustment The manual lumbar support adjustment lever is located on the right side of the driver’s seatback (all models) and on the left side of the passenger’s seatback (if equipped). Moving the lumbar control lever forward and rearward will increase or decrease the lumbar support. Eight-Way Driver’s Power Seat The driver’s power seat switches are located on the outboard side of the driver’s seat.
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. Four-Way Passenger’s Power Seat — If Equipped The front passenger’s power seat switches are located on the outboard side of the passenger’s seat. The bottom switch controls forward/rearward adjustment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 CAUTION! DO NOT place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Head Restraints Head restraints can reduce the risk of injury in the event of a rear impact. The head restraint should be adjusted so the top of the head restraint is located above the top of your ear.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision. The head restraints should always be checked prior to operating the vehicle and never adjusted while the vehicle is in motion. Always adjust the head restraints when the vehicle is in PARK. Front Heated Seats — If Equipped The front driver and passenger seats are heated.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 NOTE: Once a heat setting is selected, heat will be felt within two to five minutes. CAUTION! WARNING! Repeated overheating of the seat could damage the heating element and/or degrade the material of the seat. • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE switch indicate the level of heat in use. Two indicator Rear Heated Seats — If Equipped On vehicles equipped with rear heated seats, the seats lights will illuminate for High, one for Low and none for closest to the doors are heated. The controls for these Off. seats are located on the rear of the center console. Press the switch once to select High-level heating. Press the switch a second time to select Low-level heating.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 NOTE: Once a heat setting is selected, heat will be felt within two to five minutes. CAUTION! WARNING! Repeated overheating of the seat could damage the heating element and/or degrade the material of the seat. • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Pull the release strap (toward the front of the vehicle) to release. Rear Seat Folded To Raise Rear Seat Rear Seat Release Raise the rear seatback and lock it into place. If interferNOTE: Do not fold the rear seat down with the center ence from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its seat belt buckled. proper position. 2. Fold the rear seat completely forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. • The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the latch and lift the top of the armrest to access the pedals and radio station preset settings. Your Remote Keyless Entry (RKE) transmitters can also be prostorage bin. grammed to recall the same positions when the UNLOCK button is pressed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your vehicle is equipped with two RKE transmitters. One or both RKE transmitters can be linked to either memory position. The memory system can accommodate up to four RKE transmitters, each one linked to either of the two memory positions. Setting Memory Positions and Linking Remote Keyless Entry Transmitter to Memory 95 3. Adjust the driver’s seat, recliner, and driver’s sideview mirror to the desired positions. 4.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 10. Insert the ignition key, and turn the ignition switch to To recall the memory settings for driver one, press MEMORY button number 1 on the driver’s door, or the the ON position. UNLOCK button on the RKE transmitter linked to 11. Select ⬙Remote Linked to Memory⬙ in the Electronic memory position 1. Vehicle Information Center (EVIC) and enter ⬙Yes⬙.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Press and release MEMORY button number 1. The system will recall any memory settings stored in position 1. Wait for the system to complete the memory recall before continuing to Step 3. 97 Easy Entry/Exit Seat This feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle. 3. Press and release the memory S (SET) button located There are two possible Easy Entry/Exit adjustments on the driver’s door.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE driving position when the key is placed into the TO OPEN AND CLOSE THE HOOD ignition, and turned out of the LOCK position toward Two latches must be released to open the hood. the ACC/ON position. 1. Pull the release lever inside your vehicle located below The Easy Entry/Exit feature will be automatically dis- the instrument panel and in front of the driver’s door. abled if the seat is already positioned closer than 0.9 in (23 mm) forward of the rear stop.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Reach under the hood, move safety latch to the left and lift the hood. 99 CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ensure that both latches engage. 3 WARNING! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Headlights and Parking Lights Turn the end of the multifunction lever to the first detent Multifunction Lever for parking light operation. Turn to the second detent for The multifunction lever controls the operation of the headlight operation. Turn to the third detent for Autoheadlights, turn signals, headlight beam selection, instrumatic Headlight operation (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 This system performs two functions. With the engine Automatic Headlights — If Equipped Turn the end of the multifunction lever to the third detent running and the multifunction lever in the AUTO posi(AUTO) to activate the Automatic Headlight system. tion, the headlights will turn on and off based on the surrounding light levels.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE approximately four minutes after the wipers completely To Activate stop. Refer to “Windshield Wipers and Washers” in this 1. Select “Auto High Beams.” Refer to “Electronic Vesection for further information. hicle Information Center (EVIC)/CustomerNOTE: When your headlights come on during the Programmable Features” in “Understanding Your Instrudaytime, the instrument panel lights will automatically ment Panel” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 NOTE: Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions (sticker, toll box, etc.) on the windshield or camera lens will cause the system to function improperly. Automatic Headlight Leveling — HID Headlights Only This feature prevents the headlights from interfering with the vision of oncoming drivers.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rotate the center portion of the lever upward to the last Battery Saver Feature If the multifunction lever is left in the interior light detent to turn on the interior lighting. position, parking light position, or the headlight position when the ignition switch is moved to the LOCK position, the battery saver feature will automatically turn off the exterior and interior lights after eight minutes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 NOTE: Fog Lights — If Equipped The fog light switch is located in the multifunction • Turning on the high beam headlights turns off the fog lever. To activate the fog lights, turn on the park/ lights. turn lights, low beam headlights or the Automatic • A front fog light is a lighting device that provides Headlights and pull out the end of the multifunction illumination in front of the vehicle under conditions of lever.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE light bulb. If an indicator fails to light when the lever is Turn Signals Move the multifunction lever up or down and the arrows moved, it would suggest that the indicator bulb is on each side of the instrument cluster flash to show defective. proper operation of the front and rear turn signal lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlight Time Delay This feature delays turning off the headlights for 30, 60 or 90 seconds after the ignition switch is turned OFF. To activate the headlight delay, the multifunction lever must be rotated to the “Off” position after the ignition switch is turned to LOCK/ACC. Only the headlights will illuminate during this time.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Map/Reading Lights These lights are mounted in the overhead console. Each light can be turned on by pressing the recessed area of the lens. To turn these lights off, press the recessed area of the lens a second time. There are also reading lights located above the rear doors. Each light can be turned on by pressing the front recessed area of the lens. To turn these lights off, press the recessed area of the lens a second time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The windshield wiper/washer control lever is located on the right side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever. For information on the rear wiper/washer, refer to “Rear Window Features” in “Understanding the Features of Your Vehicle”.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Always remove any buildup of snow that prevents the windshield wiper blades from returning to the “park” position. If the windshield wiper switch is turned off, and the blades cannot return to the “park” position, damage to the wiper motor may occur. Intermittent Wiper System Use one of the five intermittent wiper speeds when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Washer Operation To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for several wipe cycles after the lever is released, and then resume the intermittent interval previously selected. Mist Use the Mist feature when weather conditions make occasional usage of the wipers necessary. Pull down and release the control lever for a single wiping cycle.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rain Sensing Wipers — If Equipped • The Rain Sensing feature may not function properly when This feature senses moisture on the windshield and ice, or dried salt water is present on the windshield. automatically activates the wipers for the driver. The • Use of Rain-X威 or products containing wax or silicone feature is especially useful for road splash or overspray may reduce Rain Sensing performance. from the windshield washers of the vehicle ahead.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 • Transmission in NEUTRAL Position — When the ignition is ON, and the transmission is in the NEUTRAL position, the Rain Sensing system will not operate until the wiper switch is moved, vehicle speed is greater than 5 mph (8 km/h), or the shift lever is moved out of the NEUTRAL position. TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your vehicle. Failure to follow this warning may result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in REVERSE (R) or when the Electronic Speed Control is on. A message will be displayed in the Electronic Vehicle Information Center (EVIC) if the pedals are attempted to be adjusted when the system is locked out (“Adjustable Pedal Disabled — Cruise Control Set” or “Adjustable Pedal Disabled — Shifter In Reverse”).
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated simultaneously. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic The Electronic Speed Control lever is located on the right Speed Control ON/OFF button and resetting the desired side of the steering wheel. vehicle set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Electronic Speed Control System on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it. 117 the set speed memory. Pressing the ON/OFF button or turning off the ignition switch erases the set speed memory.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To decrease speed while the Electronic Speed Control is set, push down and hold the SET DECEL lever. If the lever is continually held in the SET DECEL position, the set speed will continue to decrease until the lever is released. Release the lever when the desired speed is reached, and the new set speed will be established. Tapping the SET DECEL lever once will result in a 1 mph (2 km/h) speed decrease. Each time the lever is tapped, vehicle speed decreases.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKSENSE姞 REAR PARK ASSIST — IF EQUIPPED ParkSense威 provides visible and audible indications of the distance between the rear fascia and the detected obstacle when backing up. Refer to the Warning Section and Note Section for limitations of this system and recommendations. 119 ParkSense姞 Sensors The four ParkSense威 sensors, located in the rear fascia, monitor the area behind the vehicle that is within the sensors’ field of view.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense姞 Warning Display The ParkSense威 warning display, located in the headliner near the flipper glass, provides both visible and audible warnings to indicate the distance between the rear fascia and the detected obstacle. When the ignition is turned to the ON position, the warning display will turn ON all of its LEDs for about one second. Each side of the warning display has six yellow and two red LEDs.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 WARNING DISPLAY DISTANCES DISPLAY LED 1st LED 2nd LED 3rd LED 4th LED 5th LED 6th LED 7th LED 8th LED OBSTACLE DISTANCE FROM: REAR CORNERS REAR CENTER 59 in (150 cm) 51 in (130 cm) 45 in (115 cm) 31.5 in (80 cm) 39 in (100 cm) 25.5 in (65 cm) 33.5 in (85 cm) 20 in (50 cm) 28 in (70 cm) 16 in (40 cm) 20 in (50 cm) 6 in (15 cm) 12 in (30 cm) NOTE: The Rear Park Assist system will MUTE the radio, if on, when the system is sounding an audio tone.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the switch is pressed to disable the system, the instrument cluster will display the “PARK ASSIST DISABLED” message. Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. When the shift lever is changed to REVERSE and the system is disabled, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the message. information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 • When you turn ParkSense威 off, the instrument cluster • Clean the ParkSense威 sensors regularly, taking care will display “PARK ASSIST DISABLED.” Furthernot to scratch or damage them. The sensors must not more, once you turn ParkSense威 off, it remains off be covered with ice, snow, slush, mud, dirt, or debris. until you turn it on again, even if you cycle the ignition Failure to do so can result in the system not working key. properly.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! • ParkSense威 is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using ParkSense威 to be able to stop in time when the obstacle is detected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Before using the ParkSense威 Rear Park Assist System, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the warning display turns on the single flashing arc and sounds the continuous tone.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • To avoid vehicle damage, ParkView威 should only be used as a parking aid. The ParkView威 camera is unable to view every obstacle or object in your drive path. • To avoid vehicle damage, the vehicle must be driven slowly when using ParkView威 to be able to stop in time when an obstacle is seen. It is recommended that the driver look frequently over his/ her shoulder when using ParkView威.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning ParkView姞 On or Off — Without Navigation/Multimedia Radio 127 (HomeLink威) and power sunroof switches may also be included, if equipped. 1. Press the “menu” hard key. 2. Select “system setup” soft key. 3 3. Enable or disable the rear camera feature by selecting “enable rear camera in reverse” soft key. 4.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the lens to turn these lights on. Press a second time systems. The HomeLink威 unit operates off your vehicle’s battery. to turn the lights off. The lights also turn on when a front door or rear door is The HomeLink威 buttons are located in the overhead opened. The lights will also turn on when the UNLOCK console and contain one, two or three dots/lines desigbutton on the Remote Keyless Entry (RKE) transmitter is nating the different HomeLink威 channels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: HomeLink威 is disabled when the Vehicle Security Alarm is active. WARNING! • Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE HomeLink威 for more efficient training and accurate If the EVIC display states “DID NOT TRAIN” repeat transmission of the radio-frequency signal. Step 3. If the signal is too weak, replace the battery in the handheld transmitter. Your vehicle should be parked outside of the garage It may take up to 30 seconds or longer in rare cases. The while training. garage door may open and close while you train. 1. Turn the ignition switch to the ON/RUN position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 NOTE: After training a HomeLink威 channel, if the garage door does not operate with HomeLink威 and the garage door opener was manufactured after 1995, the garage door opener may have rolling code. If so, proceed to the heading “Programming A Rolling Code System.” 3 5. PROGRAMMING A ROLLING CODE SYSTEM At the garage door opener motor (in the garage), locate the “Learn” or “Training” button.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Return to the vehicle and press the programmed Similar to this Canadian law, some U.S. gate operators are HomeLink威 button twice (holding the button for two designed to “time-out” in the same manner. seconds each time). If the device is plugged in and It may be helpful to unplug the device during the cycling activates, programming is complete.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Then proceed with Step 4 under “Programming 3. Without releasing the button, proceed with Programming HomeLink威 Step 2 and follow all remaining steps. HomeLink威” earlier in this section. Using HomeLink姞 To operate, press and release the programmed HomeLink威 button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.,).
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Press the LEARN button on the garage door opener to 2. This device must accept any interference that may be received including interference that may cause undesired complete the training for rolling code. operation. • Did you unplug the device for training and remember NOTE: The transmitter has been tested and it complies to plug it back in? with FCC and IC rules.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. Power Sunroof Switch 135 WARNING! • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Express Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Closing Sunroof — Express Press the switch forward and release, and the sunroof will close automatically from any position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 NOTE: The sunshade cannot be closed if the sunroof is Ignition OFF Operation The power sunroof switches remain active for up apopen. proximately ten minutes after the ignition switch has Wind Buffeting been turned OFF. Opening either front door will cancel Wind buffeting can be described as the perception of this feature. pressure on the ears or a helicopter-type sound in the ears.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • All accessories connected to the “battery” powered outlets should be removed or turned off when the vehicle is not in use to protect the battery against discharge. • To ensure proper operation a MOPAR威 knob and element must be used. • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 WARNING! (Continued) • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. CAUTION! Rear Power Outlet WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly. Only use these intermittently and with greater caution. • After the use of high power draw accessories, or long periods of the vehicle not being started (with accessories still plugged in), the vehicle must be driven a sufficient length of time to allow the generator to recharge the vehicle’s battery.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset. If the power rating exceeds approximately 170 Watts, the power inverter may have to be reset manually. To reset the inverter manually press the power inverter button OFF and ON.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the power inverter switch (located on the upper NOTE: When the power inverter switch is pressed, switch bank) to turn the power on to the outlet. Press the there will be a delay of approximately one second before switch again to turn the power off. the inverter status indicator turns ON. The status indicator of the AC power inverter indicates whether the inverter is producing AC power.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 CUPHOLDERS There are two cupholders for the front seat passengers located in the center console. 3 Rear Cupholders CARGO AREA FEATURES Cargo Light The cargo area light is activated by opening the liftgate, The rear passengers have access to two cupholders that opening any door, or by rotating the dimmer control on pull out from the lower center of the rear seat. the multifunction lever to the extreme top position.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the cargo light lens surface will turn off all interior lights. Retractable Cargo Area Cover — If Equipped Push on the lens surface a second time to restore the NOTE: The purpose of this cover is for privacy, not to interior lights to normal operation. secure loads. It will not prevent cargo from shifting or Rear Storage Compartment protect passengers from loose cargo.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 WARNING! In an accident, a loose cargo cover in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do not store it in the vehicle.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Tie-Down Hooks The cargo tie-downs, located on the cargo area floor, should be used to safely secure loads when the vehicle is moving. Cargo Tie-Down Hooks WARNING! • To help protect against personal injury, passengers should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Do not carry loads which exceed the load limits described on the label attached to the left door or left door center pillar. • Always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible. • Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The cargo load floor is held by spring loaded latches. In REAR WINDOW FEATURES order to use the cargo load floor, use the following Rear Window Wiper/Washer procedure: The rear wiper/washer is controlled by a rotary switch NOTE: The cargo load floor latches should not be located on the control lever. The control lever is located used as cargo tie-downs. on the right side of the steering column. 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Rotate the switch upward to the “On” position to If the liftgate flipper glass is open, connection to the rear activate the rear wiper. window wiper is interrupted preventing activation of the rear wiper blade. When the liftgate flipper glass is closed, NOTE: The rear wiper operates in an intermittent mode the rear wiper switch, or the ignition switch, needs to be only. turned OFF and ON to restart the rear wiper.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 154 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . 155 䡵 Instrument Cluster Descriptions . . . . . . . . . . . 156 䡵 Electronic Vehicle Information Center (EVIC) . . 166 ▫ Electronic Vehicle Information Center (EVIC) Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 ▫ Trip Functions . . . . . . . . . . . . . . . . . . . . . . 171 ▫ Performance Pages — If Equipped . . . . .
152 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operating Instructions — Uconnect™ phone — If Equipped . . . . . . . . . . . . . . . . . . . . . . 185 ▫ Clock Setting Procedure — RBZ Radio . . . . . 185 ▫ Clock Setting Procedure — RER/REN Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 䡵 Media Center 130 (RES) — AM/FM Stereo Radio With CD Player (MP3 AUX Jack). . . . . . . 189 ▫ Operating Instructions — Radio Mode . . . . . 189 ▫ Operation Instructions — CD Mode For CD And MP3 Audio Play . .
UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Uconnect™ Multimedia (Satellite Radio) — If 䡵 Kicker威 High Performance Sound System Equipped (REN/RER/RBZ/RES Radios Only). . 215 Driver-Selectable Surround (DSS) – If Equipped . . . . . . . . . . . . . . . . . . . . . ▫ System Activation . . . . . . . . . . . . . . . . . . . . 215 䡵 Remote Sound System Controls — ▫ Electronic Serial Number/Sirius If Equipped . . . . . . . . . . . . . . . . . . . . . Identification Number (ESN/SID) . . . . . . . . .
154 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 2 3 4 — Air Outlet — Instrument Cluster — Radio — Glove Compartment 5 6 7 8 — — — — Upper Switch Bank Power Outlet/Cigar Lighter Storage Bin Power Outlet 9 — Lower Switch Bank 10 — Climate Controls 11 — Ignition Switch 12 — Storage Bin
UNDERSTANDING YOUR INSTRUMENT PANEL 155 INSTRUMENT CLUSTER 4
156 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Speedometer Indicates vehicle speed. 2. Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir.
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately. 157 The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 3.
158 UNDERSTANDING YOUR INSTRUMENT PANEL 5. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system called OBD II that monitors engine and automatic transmission control systems. The light will illuminate when the key is in the ON position before engine start. If the bulb does not come on when turning the key from OFF to ON, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc.
UNDERSTANDING YOUR INSTRUMENT PANEL 6. Airbag Warning Light This light turns on and remains on for six to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is not on during starting, stays on, or turns on while driving, have the system inspected by an authorized dealer as soon as possible. Refer to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further information. 159 required.
160 UNDERSTANDING YOUR INSTRUMENT PANEL 12. Tire Pressure Monitoring Telltale Light 10. Oil Pressure Warning Light This light indicates low engine oil pressure. The Each tire, including the spare (if provided), should be checked monthly, when cold and light should turn on momentarily when the engine inflated to the inflation pressure recommended is started. If the light turns on while driving, stop the by the vehicle manufacturer on the vehicle vehicle, and shut off the engine as soon as possible.
UNDERSTANDING YOUR INSTRUMENT PANEL 161 reduces fuel efficiency and tire tread life, and may affect approximately one minute and then remain continuously the vehicle’s handling and stopping ability. illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists.
162 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
UNDERSTANDING YOUR INSTRUMENT PANEL 163 15. Electronic Stability Program (ESP) Warning Light/Brake Assist System (BAS) Warning Light — If A hot engine cooling system is dangerous. You or Equipped The malfunction light for the Electronic Stabilothers could be badly burned by steam or boiling ity Program (ESP) is combined with Brake coolant. You may want to call an authorized dealerAssist System (BAS). The yellow “ESP/BAS ship for service if your vehicle overheats.
164 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! If a warning light remains on the system may not be working and you will not have the benefit of ESP or BAS. Under certain driving conditions, where ESP or BAS would be beneficial, you - if you have not adjusted your driving speeds and stopping in or to account for the lack of the feature, may be in accident. 16. Seat Belt Reminder Light When the ignition switch is first turned ON, this light will turn on for five to eight seconds as a bulb check.
UNDERSTANDING YOUR INSTRUMENT PANEL make a record of the odometer reading before the repair/ service, so that you can be sure that it is properly reset, or that the door jamb sticker is accurate if the odometer must be reset at zero. 19. Shift Lever Indicator The Shift Lever Indicator is self-contained within the instrument cluster. It displays the gear position of the automatic transmission. NOTE: You must apply the brakes before shifting from PARK. 20.
166 UNDERSTANDING YOUR INSTRUMENT PANEL 23. Charging System Light This light shows the status of the electrical charging system. The light should come on when the ignition switch is first turned ON and remain on briefly as a bulb check. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system.
UNDERSTANDING YOUR INSTRUMENT PANEL The EVIC consists of the following: • System Status • Vehicle Information Warning Message Displays • Personal Settings (Customer-Programmable Features) • Compass Display • Outside Temperature Display 167 The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: MENU Button Press and release the MENU button and the mode displayed will change between Trip Functions, Personal Settings, and System Status.
168 UNDERSTANDING YOUR INSTRUMENT PANEL COMPASS/TEMPERATURE Button • KEY NOT PROGRAMMED — EXCEEDED KEY PROPress and release the COMPASS/ GRAM LIMIT TEMPERATURE button to display one of eight • PROGRAMMING ACTIVE — NEW KEY PROcompass readings and the outside temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL • HOOD/DOORS OPEN (with graphic) • AUTO HIGH BEAMS ON • LIFTGATE/HOOD OPEN (with graphic) • AUTO HIGH BEAMS OFF • HOOD/GLASS/DOOR OPEN (with graphic) • PARK ASSIST DISABLED • HOOD/GLASS/DOORS OPEN (with graphic) • SERVICE SUSPENSION • HOOD/GATE/DOOR OPEN (with graphic) • SERVICE PARK ASSIST SYSTEM • HOOD/GATE/DOORS OPEN (with graphic) • TRANSMISSION OVER TEMP • LIFTGLASS/DOOR OPEN (with graphic) • LOW BRAKE FLUID LEVEL • LIFTGLASS/DOORS OPEN (with graphic)
170 UNDERSTANDING YOUR INSTRUMENT PANEL • MEMORY SYSTEM DISABLED — SEATBELT BUCK- • LEFT REAR LOW PRESSURE (Premium TPM System LED (with graphic) Only) • MEMORY SYSTEM DISABLED — VEHICLE NOT IN • RIGHT REAR LOW PRESSURE (Premium TPM SysPARK tem Only) • DRIVER 1 MEMORY • DRIVER 2 MEMORY • ADJ. PEDALS DISABLED — CRUISE CONTROL SET • ADJ.
UNDERSTANDING YOUR INSTRUMENT PANEL • 1/4 Mile (if equipped with Performance Pages) 171 • Trip A • Instantaneous G-Force (if equipped with Performance • Trip B Pages) • Elapsed Time • Peak G-Force (if equipped with Performance Pages) • Service Distance • RKE BATTERY LOW • Engine Oil Pressure • VEHICLE NOT IN PARK • Engine Oil Temperature • IGNITION POSITION • Display Units of Measure In • PRESS BRAKE TO START Press the SCROLL button to cycle through all the Trip • INSERT KEY Computer functions.
172 UNDERSTANDING YOUR INSTRUMENT PANEL and average fuel economy, according to the current fuel • Trip B tank level. DTE cannot be reset through the FUNCTION Shows the total distance traveled for Trip B since the last SELECT button. reset. NOTE: Significant changes in driving style or vehicle • Elapsed Time loading will greatly affect the actual drivable distance of Shows the total elapsed time of travel since the last reset when the ignition switch is in the ACC position.
UNDERSTANDING YOUR INSTRUMENT PANEL 173 • Display Units of Measure In Performance Pages — If Equipped To make your selection, press and release the FUNCWARNING! TION SELECT button until “ENGLISH” or “METRIC” appears. Measurement of vehicle statistics with the PerforTo Reset The Display mance Pages is intended for off-highway or off-road Reset will only occur while a resettable function is being use only and should not be done on any public displayed. Press and release the FUNCTION SELECT roadways.
174 UNDERSTANDING YOUR INSTRUMENT PANEL The Performance Pages include the following features: The following describes each feature and its operation: • 0-60 mph (0-100 km/h) 0-60 mph (0-100 km/h) When selected, this screen displays the time it takes for the vehicle to go from 0 to 60 mph (0 to 100 km/h) within 10 seconds. • Braking Distance • 1/8 Mile • 1/4 Mile • Instantaneous G-Force • Peak G-Force • The feature will “ready” when the vehicle speed is at 0 mph (0 km/h).
UNDERSTANDING YOUR INSTRUMENT PANEL 175 • To clear the vehicle’s best 0-60 mph (0-100 km/h) time, • The distance and speed measurements display while press and hold the FUNCTION SELECT button for the event is taking place. five seconds. • The distance measurement will be aborted if the brake pedal is released before the vehicle comes to a comBraking Distance When selected, this screen displays the vehicle’s braking plete stop.
176 UNDERSTANDING YOUR INSTRUMENT PANEL 1/8 Mile, 1/4 Mile • To clear the vehicle’s best 1/8 mile (1/4 mile) run, When selected, this screen displays the time it takes the press and hold the FUNCTION SELECT button for vehicle to travel 1/8 mile (1/4 mile) within 30 seconds five seconds. and the vehicle’s speed when it reaches 1/8 mile (1/ Instantaneous G-Force 4 mile).
UNDERSTANDING YOUR INSTRUMENT PANEL Compass Display The compass readings indicate the direction the vehicle is facing. Press and release the COMPASS/TEMPERATURE button to disCOMPASS play one of eight compass readings and the outside temperature. Button 177 in an area, free from magnetic material until the CAL indicator displayed in the EVIC turns off. The Compass will now function normally.
178 UNDERSTANDING YOUR INSTRUMENT PANEL 5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the “CAL” indicator turns off. The compass will now function normally. Compass Variance Compass Variance is the difference between magnetic North and Geographic North. In some areas of the country, the difference between magnetic and Geographic North is great enough to cause the compass to give false readings.
UNDERSTANDING YOUR INSTRUMENT PANEL 179 4. Press and release the FUNCTION SELECT button to Personal Settings (Customer-Programmable change the variance number. Continue until desired Features) Personal Settings allows the driver to set and recall number is reached. features when the transmission is in PARK. 5. Press either MENU, SCROLL, or COMPASS/TEMP Press and release the MENU button until “Personal button to set the value and exit. Settings” displays in the EVIC.
180 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The EVIC will not change the Uconnect™ lan- Remote Key Unlock guage selection. Please refer to “Language Selection” in When “Driver Door 1st Press” is selected, only the driver’s door will unlock on the first press of the Remote Uconnect™ Phone for details. Keyless Entry RKE transmitter UNLOCK button.
UNDERSTANDING YOUR INSTRUMENT PANEL Flash Lamps with Lock When YES (Y) is selected, the front and rear turn signals will flash when the doors are locked or unlocked with the RKE transmitter. This feature may be selected with or without the “Sound Horn with Lock” feature. To make your selection, press and release the FUNCTION SELECT button until YES (Y) or NO (N) appears. 181 SELECT button until YES (Y) or NO (N) appears.
182 UNDERSTANDING YOUR INSTRUMENT PANEL Rain Sensing Wipers — If Equipped When YES (Y) is selected, the system will automatically activate the windshield wipers if it senses moisture on the windshield. To make your selection, press and release the FUNCTION SELECT button until YES (Y) or NO (N) appears. When NO (N) is selected, the system reverts to the standard intermittent wiper operation.
UNDERSTANDING YOUR INSTRUMENT PANEL Key Off Power Delay When this feature is selected, the power window switches, radio, Uconnect™ Phone (if equipped), DVD video system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned off. Opening a vehicle door will cancel this feature. To make your selection, press and release the FUNCTION SELECT button until “Off,” “45 sec.,” “5 min.,” or “10 min.” appears.
184 UNDERSTANDING YOUR INSTRUMENT PANEL • Tire Pressure Monitor System (shows the current pres- NOTE: sure of all four road tires). For additional information, • Tires heat up during normal driving conditions. Heat will cause the tire pressure to increase from 2 to 6 psi refer to “Tire Pressure Monitor System” in “Starting (14 to 41 kPa) during normal driving conditions. Refer And Operating”. to “Tires-General Information/Tire Inflation Pressures” in “Starting And Operating” for additional information.
UNDERSTANDING YOUR INSTRUMENT PANEL 185 The REN, RER and RBZ radios contain a CD/DVD Clock Setting Procedure — RBZ Radio player, USB port, and a 30-gigabyte hard drive (HDD). To Manually Set the Clock Sirius Satellite Radio is optional. The 6.5 in (16.5 cm) 1. Turn on the radio. touch screen allows for easy menu selection. The RER radio also contains a Global Positioning System 2. Touch the screen where the time is displayed, the clock setting menu will appear on the screen. (GPS)-based Navigation system.
186 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Touch the screen where the time is displayed. The Changing Daylight Savings Time When selected, this feature will display the time of day in clock setting menu will appear on the screen. daylight savings time. Proceed as follows to change the 3. When this feature is on, a check mark will appear in current setting: the box next to the words “Show Time if Radio is Off.” Touch the screen where the words “Show Time if Radio is 1. Turn on the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 187 5. Touch the screen where the word “Save” is displayed. 4. To move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is disClock Setting Procedure — RER/REN Radio played. To move the hour backward, touch the screen where the word “Hour” with the arrow pointing downUconnect威 gps — RER Only The GPS receiver used in this system is synchronized to ward is displayed. the time data being transmitted by the GPS satellite. The 5.
188 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Touch the screen where “User Clock” is displayed, the clock setting menu will appear on the screen. Touch the screen where the words “Show Time if Radio is Off” are displayed to change the current setting. 3. When this feature is on, a check mark will appear in Changing the Time Zone the box next to the words “Daylight Savings.” Touch the 1. Turn on the radio. screen where the words “Daylight Savings” are dis2. Touch the screen where the time is displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 130 (RES) — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) 189 Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC NOTE: The radio sales code is located on the lower right position to operate the radio. side of the radio faceplate. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
190 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save time change. 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 191 Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the AM/FM Button mid-range tones. Press the buttons to select either AM or FM mode. Push the rotary TUNE/SCROLL control knob a third SET/RND Button — To Set the Pushbutton time and TREBLE will display.
192 UNDERSTANDING YOUR INSTRUMENT PANEL SET 2 in both AM and FM. This allows a total of 12 AM Operation Instructions — CD MODE For CD And and 12 FM stations to be stored into pushbutton memory. MP3 Audio Play The stations stored in SET 2 memory can be selected by NOTE: pressing the pushbutton twice. • The ignition switch must be in the ON or ACC position to operate the radio. Every time a preset button is used, a corresponding button number will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 193 If you insert a disc with the ignition ON and the radio EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. If you have ejected a disc and have not removed it within CAUTION! 10 seconds, it will be reloaded.
194 UNDERSTANDING YOUR INSTRUMENT PANEL the current selection. Pressing and holding the SEEK SET/RND Button (Random Play Button) button will allow faster scrolling through the tracks in Press this button while the CD is playing to activate Random Play. This feature plays the selections on the CD and MP3 modes. compact disc in random order to provide an interesting TIME Button change of pace. Press this button to change the display from a large CD playing time display to a small CD playing time display.
UNDERSTANDING YOUR INSTRUMENT PANEL 195 exceeding 20 folders will result in this display. With Supported Medium Formats (File Systems) 200 files, exceeding 50 folders will result in this The medium formats supported by the radio are ISO 9660 display.) Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than • Maximum number of characters in file/folder names: ISO 9660 Level 1 and Level 2, the radio may fail to read • Level 1: 12 (including a separator ⬙.
196 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. MPEG Specification MPEG-1 Audio Layer 3 Sampling Bit Rate (kbps) Frequency (kHz) 320, 256, 224, 192, 160, 128, 48, 44.1, 32 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 24, 22.
UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
198 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 130 (RES/RSC) — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) AND SIRIUS RADIO Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate. Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it.
200 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Adjust the hours by turning the right side TUNE/ INFO Button Press the INFO button for an RDS station (one with call SCROLL control knob. letters displayed). The radio will return a Radio Text 3. After adjusting the hours, press the right side TUNE/ message broadcast from an FM station (FM mode only). SCROLL control knob to set the minutes. The minutes RW/FF will begin to blink. Pressing the RW (Rewind) or FF (Fast Forward) buttons 4.
UNDERSTANDING YOUR INSTRUMENT PANEL 201 Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the MUSIC TYPE Button mid-range tones. Pressing this button once will turn on the Music Type Push the rotary TUNE/SCROLL control knob a third mode for five seconds. Pressing the MUSIC TYPE button time and TREBLE will display.
202 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Classic Rock College Country Foreign Language Information Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock 16-Digit Character Display Cls Rock College Country Language Inform Jazz News Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Program Type Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 16-Digit Character Display Soft Soft Rck Soft R&B Sports Talk Top 40 Weather By pr
UNDERSTANDING YOUR INSTRUMENT PANEL 203 window. Select the button (1–6) you wish to lock onto this SETUP Button Pressing the SETUP button allows you to select between station and press and release that button. If a button is not selected within five seconds after pressing the SET/ the following items: RND button, the station will continue to play but will not • Set Clock — Pressing the SELECT button will allow be stored into pushbutton memory. you to set the clock.
204 UNDERSTANDING YOUR INSTRUMENT PANEL Buttons 1 - 6 Inserting Compact Disc(s) These buttons tune the radio to the stations that you Gently insert one CD into the CD player with the CD commit to pushbutton memory (12 AM and 12 FM label facing up. The CD will automatically be pulled into stations). the CD player and the CD icon will illuminate on the radio display. If a CD does not go into the slot more than DISC/AUX Button 1.0 in (2.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! (Continued) • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • RES is a single CD player. Do not attempt to insert a second CD if one is already loaded. • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player. EJECT Button - Ejecting a CD Press the EJECT button to eject the CD.
206 UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button Press the button to select either AM or FM mode. SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Supported Media (Disc Types) The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3.
UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of folders. (The radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name and will assign a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.) 207 writing⬙ are most likely multisession discs.
208 UNDERSTANDING YOUR INSTRUMENT PANEL MPEG Specification MPEG-1 Audio Layer 3 MPEG-2 Audio Layer 3 Sampling Bit Rate (kbps) Frequency (kHz) 320, 256, 224, 192, 160, 128, 48, 44.1, 32 112, 96, 80, 64, 56, 48, 40, 32 160, 128, 144, 112, 96, 80, 64, 24, 22.05, 16 56, 48, 40, 32, 24, 16, 8 Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium.
UNDERSTANDING YOUR INSTRUMENT PANEL LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob. Selecting a folder by pressing the TUNE/SCROLL control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain playable files). The folder list will time out after five seconds.
210 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Press this button to change the display to time of day. The time of day will display for five seconds (when the ignition is OFF). RER, RBZ, REN, REP, REW, RB2 or REZ touch-screen radio UCI feature, refer to the separate RER, REN, RBZ, RB2 or REZ User’s Manual. UCI is available only if equipped as an option with these radios.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 • Connecting an iPod威 to the AUX port located in the • If the iPod威 battery is completely discharged, it may radio faceplate, plays media, but does not use the UCI not communicate with the UCI system until a minifeature to control the connected device. mum charge is attained. Leaving the iPod威 connected to the UCI system may charge it to the required level.
212 UNDERSTANDING YOUR INSTRUMENT PANEL Once in the UCI (iPod威) mode, iPod威 audio tracks (if available from iPod威) start playing over the vehicle’s audio system. • Jump backward in the current track by pressing and holding the << RW button. Holding the << RW button long enough will take you to the beginning of the current track. Play Mode When switched to UCI mode, the iPod威 automatically • Jump forward in the current track by pressing and starts Play mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 Shuffle OFF modes for the iPod威. If the RND icon is • While a track is playing, press the INFO button to see showing on the radio display, then the shuffle mode is the associated metadata (artist, track title, album, etc.) ON. for that track. Pressing the INFO button again jumps to the next screen of data for that track.
214 UNDERSTANDING YOUR INSTRUMENT PANEL • During all List modes, the iPod威 displays all lists in “wrap-around” mode. So if the track is at the bottom of the list, just turn the wheel backwards (counter-clockwise) to get to the track faster. • In List mode, the radio PRESET buttons are used as shortcuts to the following lists on the iPod威.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! • Leaving the iPod威 (or any supported device) anywhere in the vehicle in extreme heat or cold can alter the operation or damage the device. Follow the device manufacturer’s guidelines. • Placing items on the iPod威, or connections to the iPod威 in the vehicle, can cause damage to the device and/or to the connectors. WARNING! Do not plug in or remove the iPod威 while driving. Failure to follow this warning could result in an accident.
216 UNDERSTANDING YOUR INSTRUMENT PANEL information, call the toll-free number 888-539-7474, or Sirius ID number will display. The Sirius ID number visit the Sirius web site at www.sirius.com, or at www- display will time out in two minutes. Press any button on the radio to exit this screen. .siriuscanada.ca for Canadian residents.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 bikes should be placed as far rearward as possible, within Operating Instructions - Uconnect™ Multimedia the loading design of the rack. Do not place items directly (Satellite) Mode on or above the antenna. NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
218 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button Pressing the INFO button will cycle the display information between Artist, Song Title, and Composer (if available). Also, pressing and holding the INFO button for an additional three seconds will make the radio display the Song Title all of the time (press and hold again to return to normal display). MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 You may add a second channel to each pushbutton by SETUP Button Pressing the SETUP button allows you to select the repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display following items: window. Each button can be set for SET 1 and SET 2. This • Display Sirius ID number — Press the AUDIO/ allows a total of 12 Satellite channels to be stored into SELECT button to display the Sirius ID number.
220 UNDERSTANDING YOUR INSTRUMENT PANEL KICKER姞 HIGH PERFORMANCE SOUND SYSTEM WITH DRIVER-SELECTABLE SURROUND (DSS) – IF EQUIPPED Your vehicle is equipped with a state of the art audio amplifier that provides 5.1-channel surround sound from any stereo audio source. Anew feature of the KICKER威 audio system offers the ability to choose surround sound for any audio source or video source.
UNDERSTANDING YOUR INSTRUMENT PANEL Installing The Subwoofer 1. Lower the left rear passenger seat. 221 2. Align the left outside edge of the subwoofer with the outside edge of the inner cargo tie down hook.
222 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Slide the subwoofer toward the front of the vehicle so Removing The Subwoofer that the rear edge lines up with the end of the load floor. 1. Lower the left rear passenger seat. 4. Connect the electrical connector. 2. Disconnect the electrical connector. 5. Fold the left rear passenger seat rearward into the 3. Remove the subwoofer. upright position. The rear tether anchors should engage the hooks located on the back of the subwoofer.
UNDERSTANDING YOUR INSTRUMENT PANEL REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. 223 The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and mode of the sound system. Pressing the top of the rocker switch will increase the volume, and pressing the bottom of the rocker switch will decrease the volume.
224 UNDERSTANDING YOUR INSTRUMENT PANEL The button located in the center of the left-hand control CD/DVD DISC MAINTENANCE will tune to the next preset station that you have pro- To keep a CD/DVD in good condition, take the following precautions: grammed in the radio preset pushbutton. CD Player Pressing the top of the switch once will go to the next track on the CD.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particular disc, it may be damaged (i.e., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service. 225 CLIMATE CONTROLS Automatic Temperature Control The Automatic Temperature Control System automatically maintains the interior comfort level desired by the driver and passenger.
226 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The numbers on the temperature dial represent You will experience the greatest efficiency by simply a comfort setting when the Mode knob is set to AUTO, allowing the system to function automatically. Selecting the OFF (O) position on the blower control knob stops the and not the actual air temperature. system completely.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 The system will automatically control re- • Under certain conditions (after the vehicle is turned circulation. However, pressing this butoff) the climate control system may recalibrate and a ton will temporarily put the system in noise may be heard for 20 seconds. This is part of “Recirculation” mode. This can be used normal operation.
228 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Manual Operation This system offers a full complement of manual override • For vehicles equipped with Remote Start, the climate features which consist of Blower Preferred Automatic, controls will not function during Remote Start operaMode Preferred Automatic with Manual Air Temperature tion if the blower control is left in the “O” (Off) Control, and Manual. This means the customer can position.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 4
230 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Regardless of the type of operation, when a NOTE: The defrost mode is not automatically selected. temperature knob is set to the full clockwise or full It must be manually selected, when desired. counterclockwise position, the system will deliver full Defrost/Floor hot or full cold air out of the ducts, respectively.
UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Air flows both through the outlets located in the instrument panel and those located on the floor. Air flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to block airflow. The center console outlets deliver conditioned air while the floor outlets deliver heated air. 231 outlets selected on the mode control dial.
232 UNDERSTANDING YOUR INSTRUMENT PANEL captured interior air to condense on windows and hamper visibility. For this reason, the system will not allow “Recirculation” mode to be selected while in the defrost or defrost/floor modes. Attempting to use Recirculation while in these modes will cause the LED in the button to blink and then turn off. Operating Tips Window Fogging Windows will fog on the inside when the humidity inside the vehicle is high.
UNDERSTANDING YOUR INSTRUMENT PANEL additional engine cooling may be required. If this situation is encountered, operate the transmission in a lower gear to increase engine RPM, coolant flow and fan speed. When stopped in heavy traffic, it may be necessary to shift into NEUTRAL (N) and press the accelerator slightly for fast idle operation to increase coolant flow and fan speed. Your air conditioning system is also equipped with an automatic recirculation system.
234 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Chart
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 238 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 238 ▫ Extreme Cold Weather (Below ⫺20°F Or ⫺29°C) . . . . . . . . . . . . . . . 239 ▫ Brake/Transmission Interlock Manual Override . . . . . . . . . . . . . . . . . . . . . . . . . . 241 ▫ Five–Speed Automatic Transmission . . . . . . . 242 ▫ Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . 243 ▫ If Engine Fails To Start . . . . . . . . .
236 STARTING AND OPERATING ▫ Power Steering Fluid Check . . . . . . . . . . . . . 249 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . 262 䡵 Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . 250 ▫ Tire Identification Number (TIN) . . . . . . . . . 266 䡵 Anti-Lock Brake System . . . . . . . . . . . . . . . . . 252 ▫ Tire Terminology And Definitions . . . . . . . . . 267 䡵 Electronic Brake Control System . . . . . . . . . . . 255 ▫ Tire Loading And Tire Pressure . . . . . . .
STARTING AND OPERATING ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . 277 237 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . 286 䡵 Tire Rotation Recommendations . . . . . . . . . . . 278 䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 287 䡵 Tire Pressure Monitor System (TPMS) . . . . . . . 279 ▫ Fuel Filler Cap (Gas Cap) . . . . . . . . . . . . . . 287 ▫ Premium System . . . . . . . . . . . . . . . . . . . . 279 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . .
238 STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key fob in the ignition switch.
STARTING AND OPERATING Extreme Cold Weather (Below ⫺20°F or ⫺29°C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your authorized dealer) is recommended. If Engine Fails To Start WARNING! • Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury.
240 STARTING AND OPERATING If the engine fails to start after you have followed the AUTOMATIC TRANSMISSION “Normal Starting” or “Extreme Cold Weather” proceCAUTION! dures, it may be flooded. To clear any excess fuel, push the accelerator pedal all the way to the floor and hold it. Damage to the transmission may occur if the followThen, turn the ignition switch to the START position and ing precautions are not observed: release it as soon as the starter engages.
STARTING AND OPERATING WARNING! It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your foot is firmly on the brake pedal.
242 STARTING AND OPERATING 3. Using a flat blade screwdriver, carefully remove the 6. Move the shift lever into the NEUTRAL position. shift lock manual override cover which is located on the 7. The vehicle may then be started in NEUTRAL. PRNDL bezel. 4. Press and maintain firm pressure on the brake pedal. Have your vehicle inspected by your local authorized dealer, if the shift lock manual override has been used. 5.
STARTING AND OPERATING WARNING! It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your foot is firmly on the brake pedal.
244 STARTING AND OPERATING WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should apply the park brake, shift the transmission into PARK, and remove the key fob from the ignition switch. Once the key fob is removed from the ignition switch, the shift lever is locked in the PARK position, securing the vehicle against unwanted movement.
STARTING AND OPERATING NOTE: The Electronic Stability Program (ESP) and Traction Control (if equipped) should be turned OFF before attempting to rock the vehicle. Refer to “Electronic Brake Control System” in “Starting and Operating” for further information. The least amount of accelerator pedal pressure to maintain the rocking motion without spinning the wheels or racing the engine is most effective.
246 STARTING AND OPERATING Operation By placing the shift lever in the DRIVE position, the shift lever can be moved from side to side. This allows the driver to engage the AutoStick威 mode. Moving the shift lever to the right (+) or the left (-) will engage the AutoStick威 mode. In normal driving mode (Boxed “D” displayed in the PRNDL), moving the shift lever to the right (+) will engage the AutoStick威 mode putting the transmission in the currently engaged gear.
STARTING AND OPERATING When in the AutoStick威 mode, as the engine RPM nears the engine maximum speed, an “UPSHIFT” message will appear in the Electronic Vehicle Information Center (EVIC) portion of your instrument cluster. This message appears in order to alert the driver that the engine speed is approaching it’s maximum value and a upshift to the next gear is required. In the event that the driver does not upshift, the engine control system will automatically do it for the driver.
248 STARTING AND OPERATING • The transmission will automatically shift up when NOTE: maximum engine speed is reached while AutoStick威 is • Increased noise levels at the end of the steering wheel travel are considered normal and do not indicate that engaged. there is a problem with the power steering system. • Transmission shifting will be more noticeable when • Upon initial start-up in cold weather, the power steerAutoStick威 is engaged. ing pump may make noise for a short amount of time.
STARTING AND OPERATING 249 CAUTION! WARNING! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible. Damage to the power steering pump may occur. Do not use Automatic Transmission Fluid (ATF), or other types of power steering fluids, when servicing the power steering system of this vehicle. Damage to the power steering system can result from the use of the wrong power steering fluid.
250 STARTING AND OPERATING WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. possible. To release the parking brake, pull the lever up slightly, press the center button, then lower the lever completely. If necessary, add fluid to restore to the proper indicated level.
STARTING AND OPERATING NOTE: • When the parking brake is applied vehicle speed is detected, the light will flash and a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • This light only shows that the parking brake is applied. It does not show the degree of brake application. When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.
252 STARTING AND OPERATING WARNING! (Continued) • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury. Also be certain to leave the transmission in PARK. Failure to do so may allow the vehicle to roll and cause damage or injury. CAUTION! If the “Brake Warning Light” remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately.
STARTING AND OPERATING The Anti-Lock Brake System pump motor runs during the self-test at 12 mph (20 km/h) and during an ABS stop. The pump motor makes a low humming noise during operation, which is normal. WARNING! • Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
254 STARTING AND OPERATING NOTE: During severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard. This is normal, indicating that the Anti-Lock Brake System is functioning. WARNING! To use your brakes and accelerator more safely, follow these tips: • Do not “ride” the brakes by resting your foot on the pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping distances, or brake damage.
STARTING AND OPERATING ELECTRONIC BRAKE CONTROL SYSTEM Your vehicle is equipped with an advanced electronic brake control system that includes Anti-Lock Brake System (ABS), Traction Control System (TCS), Brake Assist System (BAS), Electronic Roll Mitigation (ERM), and Electronic Stability Program (ESP). All five of these systems work together to enhance vehicle stability and control in various driving conditions. Also, your vehicle is equipped with Trailer Sway Control (TSC).
256 STARTING AND OPERATING stability. A feature of the TCS system functions similar to a limited slip differential and controls the wheel spin across a driven axle. If one wheel on a driven axle is spinning faster than the other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not spinning. This feature remains active even if TCS and ESP are in the “ESP Partial Off” mode.
STARTING AND OPERATING Electronic Roll Mitigation (ERM) This system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When ERM determines that the rate of change of the steering wheel angle and vehicles speed are sufficient to potentially cause wheel lift, it then applies the appropriate brake and may also reduce engine power to lessen the chance that wheel lift will occur.
258 STARTING AND OPERATING the brake of the appropriate wheel to assist in counteracting the over/under steer condition. Engine power may also be reduced to help the vehicle maintain the desired path. ESP uses sensors in the vehicle to determine the vehicle path intended by the driver and compares it to the actual path of the vehicle. When the actual path does not match the intended path, ESP applies the brake of the appropriate wheel to assist in counteracting the oversteer or understeer condition.
STARTING AND OPERATING The ESP system has two available operating modes. On This is the normal operating mode for ESP. Whenever the vehicle is started, the ESP system will be in this “On” mode. This mode should be used for most driving situations. ESP should only be turned to “Partial Off” mode for specific reasons as noted below. 259 turn ESP on again, momentarily press the ⬙ESP OFF” switch. This will restore the normal “ESP On” mode of operation.
260 STARTING AND OPERATING Off” mode by pressing the “ESP OFF” switch. Once the situation requiring ESP to be switched to the “ESP Partial Off” mode is overcome, turn ESP back on by momentarily pressing the “ESP OFF” switch. This may be done while the vehicle is in motion. Trailer Sway Control (TSC) TSC uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appropriate actions to attempt to stop the sway.
STARTING AND OPERATING 261 If the “ESP/BAS Warning Light” comes on • Each time the ignition switch is turned to the ON continuously with the engine running, a malposition, the ESP System will be ON even if it was function has been detected in either the ESP or turned off previously. the BAS system, or both. If this light remains on • The ESP Control System will make buzzing or clicking after several ignition switch cycles, and the vehicle has sounds when it is active.
262 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
STARTING AND OPERATING 263 • Temporary spare tires are high-pressure compact • High flotation tire sizing is based on U.S. design spares designed for temporary emergency use only. standards and it begins with the tire diameter molded Tires designed to this standard have the letter “T” into the sidewall. Example: 31x10.5 R15 LT. molded into the sidewall preceding the size designation. Example: T145/80D18 103M.
264 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
STARTING AND OPERATING 265 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
266 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
STARTING AND OPERATING 267 Tire Terminology and Definitions Term B-Pillar Cold Tire Pressure Maximum Inflation Pressure Recommended Inflation Pressure Tire Placard Definition The vehicle B-Pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.
268 STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar.
STARTING AND OPERATING 269 To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard. Loading The combined weight of occupants, cargo/luggage and The vehicle maximum load on the tire must not exceed trailer tongue weight (if applicable) should never exceed the load carrying capacity of the tire on your vehicle. You the weight referenced here.
270 STARTING AND OPERATING 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if “XXX” • The following table shows examples on how to calculate total load, cargo/luggage, and towing capacities amount equals 1,400 lbs (635 kg) and there will be five of your vehicle with varying seating configurations 150 lb (68 kg) passengers in your vehicle, the amount of and number and size of occupants.
STARTING AND OPERATING 271 5
272 STARTING AND OPERATING WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Do not exceed 50 mph (80 km/h) if the “Tire Pressure Monitoring Telltale Light” is illuminated. Vehicle handling and braking may be reduced. You could have an accident and be severely or fatally injured.
STARTING AND OPERATING Safety WARNING! • Improperly inflated tires are dangerous and can cause accidents. • Under inflation increases tire flexing and can result in over-heating and tire failure. • Over inflation reduces a tire’s ability to cushion shock. Objects on the road and chuck holes can cause damage that results in tire failure. • Unequal tire pressures can cause steering problems. You could lose control of your vehicle.
274 STARTING AND OPERATING Tire Inflation Pressures is defined as the tire pressure after the vehicle has not The proper cold tire inflation pressure is listed on the been driven for at least three hours, or driven less than driver’s side “B” Pillar. 1 mile (1.6 km) after a three hour period. The cold tire inflation pressure must not exceed the maximum inflaThe pressure should be checked and adjusted as well as tion pressure molded into the tire side wall.
STARTING AND OPERATING Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. 275 WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Do not drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
276 STARTING AND OPERATING Cuts and punctures in radial tires are repairable only in Tread Wear Indicators the tread area because of sidewall flexing. Consult your Tread wear indicators are in the original equipment tires to help you in determining when your tires should be dealer for radial tire repairs. replaced. Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h). WARNING! Fast spinning tires can be dangerous.
STARTING AND OPERATING 277 These indicators are molded into the bottom of the tread Keep unmounted tires in a cool, dry place with as little grooves. They will appear as bands when the tread depth exposure to light as possible. Protect tires from contact becomes 1/16 in (2 mm). When the tread is worn to the with oil, grease and gasoline. tread wear indicators, the tire should be replaced.
278 STARTING AND OPERATING WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM (TPMS) 279 • Various Tire Pressure Monitoring System Messages, which display in the Electronic Vehicle Information Center (EVIC), and a graphic displaying tire pressures Premium System The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to • Tire Pressure Monitoring Telltale Light monitor tire pressure levels.
280 STARTING AND OPERATING NOTE: Your system can be set to display pressure units The system will automatically update, the graphic disin PSI, kPa, or BAR. play of the pressure value(s) will stop flashing, and the “Tire Pressure Monitoring Telltale Light” will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information.
STARTING AND OPERATING 281 1. Jamming due to electronic devices or driving next to facilities emitting the same Radio Frequencies as the TPM sensors. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPM sensors. If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists.
282 STARTING AND OPERATING General Information FUEL REQUIREMENTS This device complies with part 15 of the FCC rules and 6.1L Engine RSS 210 of Industry Canada. Operation is subject to the The 6.1L engine is designed to meet all following conditions: emissions regulations and provide excel• This device may not cause harmful interference.
STARTING AND OPERATING 283 Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the Worldwide Fuel Charter, WWFC) which define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recommends the use of gasoline that meets the WWFC specifications, if they are available. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as 10% ethanol, MTBE, and ETBE.
284 STARTING AND OPERATING E85 Usage In Non-Flex Fuel Vehicles • disconnect and reconnect the battery to reset the Non-FFV vehicles are compatible with gasoline containengine controller memory ing 10% ethanol (E10). Gasoline with higher ethanol More extensive repairs will be required for prolonged content may void the vehicle’s warranty. exposure to E85 fuel.
STARTING AND OPERATING can be used at levels higher than those allowed in the United States. MMT is prohibited in Federal and California reformulated gasoline. Materials Added to Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and they would result in additional cost. Therefore, you should not have to add anything to the fuel.
286 STARTING AND OPERATING NOTE: Intentional tampering with the emissions control system can result in civil penalties being assessed against you. Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: (Continued) WARNING! (Continued) • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill.
STARTING AND OPERATING ADDING FUEL 287 CAUTION! Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel filler door, on the driver’s side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. Fuel Filler Cap • Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system.
288 STARTING AND OPERATING WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel when the engine is running. This is in violation of most state and federal fire regulations and will cause the MIL to turn on. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
STARTING AND OPERATING TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer carefully review this information to tow your load as efficiently and safely as possible. WARNING! • Do not tow when the “Tire Pressure Monitoring Telltale Light” is illuminated. Failure to follow this could result in loss of control and serious injury.
290 STARTING AND OPERATING Gross Combination Weight Rating (GCWR) Tongue Weight (TW) The GCWR is the total permissible weight of your vehicle The tongue weight is the downward force exerted on the and trailer when weighed in combination. hitch ball by the trailer. In most cases it should not be less than 10% or more than 15% of the trailer load. You must NOTE: The GCWR rating includes a 150 lbs (68 kg) consider this as part of the load on your vehicle. allowance for the presence of a driver.
STARTING AND OPERATING Weight-Distributing Hitch A weight-distributing system works by applying leverage through spring (load) bars. They are typically used for heavier loads, to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturers’ directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.
292 STARTING AND OPERATING Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the Trailer Towing Weights (Maximum Trailer Weight Ratings) chart for the Max. GTW towable for your given drivetrain. Trailer Hitch Classification Definitions Class Max.
STARTING AND OPERATING 293 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ Transmission 6.1L Automatic GCWR (Gross Combined Frontal Area Max. GTW (Gross Wt. Rating) Trailer Wt.) 8,800 lbs (3 992 kg) 35 sq ft (3.25 sq m) 3,500 lbs (1 587 kg) Refer to local laws for maximum trailer towing speeds.
294 STARTING AND OPERATING Never exceed the maximum tongue weight stamped on Consider the following items when computing the your trailer hitch. weight on the front/rear axles of the vehicle: • The trailer tongue weight of the trailer. • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle.
STARTING AND OPERATING Towing Requirements To promote proper break-in of your new vehicle drivetrain components the following guidelines are recommended: CAUTION! • Do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven. The engine, axle or other parts could be damaged. • Then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle.
296 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle transmission in PARK. Always, block or ⴖchockⴖ the trailer wheels.
STARTING AND OPERATING 297 − Check for signs of tire wear or visible tire damage − An electronically actuated trailer brake controller is before towing a trailer. Refer to “Tires – General required when towing a trailer with electronically Information” in “Starting and Operating” for proper actuated brakes. When towing a trailer equipped with inspection procedure. a hydraulic surge actuated brake system, an electronic brake controller is not required.
298 STARTING AND OPERATING WARNING! • Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. • Towing any trailer will increase your stopping distance. When towing you should allow for additional space between your vehicle and the vehicle in front of you. Failure to do so could result in an accident.
STARTING AND OPERATING 299 − When using the speed control, if you experience speed RECREATIONAL TOWING (BEHIND drops greater than 10 mph (16 km/h), disengage until MOTORHOME, ETC.) Recreational towing is not allowed. you can get back to cruising speed. − Use speed control in flat terrain and with light loads to maximize fuel efficiency.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flashers . . . . . . . . . . . . . . . . 302 ▫ Preparations For Jump-Start . . . . . . . . . . . . . 305 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 302 ▫ Jump-Starting Procedure . . . . . . . . . . . . . . . 306 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 304 䡵 Emergency Tow Hooks — If Equipped . . . . . . 308 ▫ Run Flat Tires . . . . . . . . . . . . . . . . . . . . . . . 304 䡵 Towing A Disabled Vehicle . . . . . . . .
302 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the switch bank just above the climate controls. potential for overheating by taking the appropriate action. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional • On the highways — Slow down.
WHAT TO DO IN EMERGENCIES CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads HOT (H), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on HOT (H), and you hear continuous chimes, turn the engine off immediately and call for service.
304 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING JUMP-STARTING PROCEDURES If your vehicle has a discharged battery it can be jumpRun Flat Tires started using a set of jumper cables and a battery in This vehicle is equipped with run flat tires. Although the another vehicle or by using a portable battery booster tires are designed with a “run flat” feature that allows the pack.
WHAT TO DO IN EMERGENCIES WARNING! When temperatures are below the freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump-starting because the battery could rupture or explode and cause personal injury. Battery temperature must be brought above freezing point before attempting a jump-start. 305 Preparations for Jump-Start The battery in your vehicle is located in the front of the engine compartment, behind the left headlight assembly.
306 WHAT TO DO IN EMERGENCIES WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
WHAT TO DO IN EMERGENCIES 307 CAUTION! WARNING! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 5.
308 WHAT TO DO IN EMERGENCIES 8. Disconnect the opposite end of the positive (+) jumper EMERGENCY TOW HOOKS — IF EQUIPPED If your vehicle is equipped with tow hooks, there will be cable from the positive (+) post of the booster battery. one in the rear and two mounted on the front of the 9. Disconnect the positive (+) end of the jumper cable vehicle. The rear hook will be located on the driver’s side from the positive (+) post of the discharged vehicle. of the vehicle. 10. Reinstall the air intake duct.
WHAT TO DO IN EMERGENCIES 309 WARNING! CAUTION! Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. • Towing this vehicle using any other method could result in extensive damage to the transfer case and/or transmission. • Such damage is not covered by the New Vehicle Limited Warranty. TOWING A DISABLED VEHICLE The manufacturer requires towing your vehicle with all four wheels OFF the ground using a flatbed.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment – 6.1L . . . . . . . . . . . . . . 313 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 321 䡵 Onboard Diagnostic System – OBD II . . . . . . . 314 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . 321 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . 314 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . 322 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . .
312 MAINTAINING YOUR VEHICLE ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . 334 ▫ Automatic Transmission . . . . . . . . . . . . . . . 335 ▫ High Intensity Discharge Headlamps (HID) — If Equipped . . . . . . . . . . . . . . . . . . . . . . 349 ▫ Halogen Headlamps — If Equipped . . . . . . . 350 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . 336 ▫ Front Turn Signal . . . . . . . . . . . . . . . . . . . . 351 䡵 Fuses . . . . . . . . . .
MAINTAINING YOUR VEHICLE 313 ENGINE COMPARTMENT – 6.
314 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM – OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 315 gas cap until a ⬙clicking⬙ sound is heard. This is an EMISSIONS INSPECTION AND MAINTENANCE indication that the gas cap is properly tightened. PROGRAMS In some localities, it may be a legal requirement to pass The message will remain displayed until the vehicle an inspection of your vehicle’s emissions control system. diagnostic system can retest the fuel system. The test will Failure to pass could prevent vehicle registration.
316 MAINTAINING YOUR VEHICLE Your vehicle has a simple ignition key-actuated test, which you can use prior to going to the test station. To check if your vehicle’s OBD II system is ready, you must do the following: 1. Turn the ignition switch to the ON position, but do not crank or start the engine. the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station. b.
MAINTAINING YOUR VEHICLE 317 before going to the I/M station. The I/M station can fail NOTE: Intentional tampering with emissions control your vehicle because the MIL is on with the engine systems may void your warranty and could result in civil penalties being assessed against you. running. REPLACEMENT PARTS Use of genuine MOPAR威 parts for normal/scheduled maintenance and repairs is highly recommended to ensure the designed performance.
318 MAINTAINING YOUR VEHICLE Besides those maintenance items specified in the fixed maintenance schedule, there are other components which may require servicing or replacement in the future. CAUTION! • Failure to properly maintain your vehicle or perform repairs and service when necessary could result in more costly repairs, damage to other components or negatively impact vehicle performance.
MAINTAINING YOUR VEHICLE check the engine oil level is about five minutes after a fully warmed engine is shut off or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level in the “SAFE” range. Adding one quart of oil when the reading is at the bottom of the “SAFE” range will result in an oil level at the top of the “SAFE” range on these engines.
320 MAINTAINING YOUR VEHICLE requirements of Chrysler Material Standard MS-10725 The engine oil filler cap also shows the recommended and are approved to MB 229.3 or MB 229.5 (will be listed engine oil viscosity for your engine. For information on on the back label of the oil container). engine oil filler cap location, refer to “Engine Compartment” in Maintaining Your Vehicle” for further The manufacturer recommends the use of a full synthetic information. 5W-40 or equivalent engine oil.
MAINTAINING YOUR VEHICLE 321 Disposing of Used Engine Oil and Oil Filters Engine Air Cleaner Filter Care should be taken in disposing of used engine oil and Refer to “Maintenance Schedule” for further information. oil filters from your vehicle. Used oil and oil filters, WARNING! indiscriminately discarded, can present a problem to the environment.
322 MAINTAINING YOUR VEHICLE Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic maintenance required. CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case.
MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Warranty Information Book, located on the DVD, for further warranty information. • The air conditioning system contains refrigerant under high pressure.
324 MAINTAINING YOUR VEHICLE When performing other underhood services, the hood Avoid using the wiper blades to remove frost or ice from latch, release mechanism and safety catch should be the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the Fall and Spring.
MAINTAINING YOUR VEHICLE The fluid reservoir for the windshield washers and the rear window washer is shared. The fluid reservoir is located in the engine compartment, be sure to check the fluid level at regular intervals. Fill the reservoir with windshield washer solvent only (not radiator antifreeze). When refilling the washer fluid reservoir, take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades, this will help blade performance.
326 MAINTAINING YOUR VEHICLE inspect the exhaust system each time the vehicle is raised Under normal operating conditions, the catalytic converter will not require maintenance. However, it is imfor lubrication or oil change. Replace as required. portant to keep the engine properly tuned to assure WARNING! proper catalyst operation and prevent possible catalyst damage. Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless.
MAINTAINING YOUR VEHICLE 327 NOTE: Intentional tampering with emissions control To minimize the possibility of catalyst damage: systems can result in civil penalties being assessed • Do not shut off the engine or interrupt the ignition against you. when the transmission is in gear and the vehicle is in motion. WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system.
328 MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position. • You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.
MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush and Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant (antifreeze). Refer to “Maintenance Schedule” for further information. Selection Of Coolant Use only the manufacturer’s recommended coolant.
330 MAINTAINING YOUR VEHICLE CAUTION! (Continued) • This vehicle has not been designed for use with Propylene Glycol based engine coolant (antifreeze). Use of Propylene Glycol based engine coolant (antifreeze) is not recommended. When adding engine coolant (antifreeze): • The manufacturer recommends using MOPAR威 Antifreeze/ Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent.
MAINTAINING YOUR VEHICLE NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and will require more frequent engine coolant (antifreeze) changes. Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle.
332 MAINTAINING YOUR VEHICLE Disposal of Used Engine Coolant Used ethylene glycol based engine coolant (antifreeze) is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children, do not store ethylene glycol based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately.
MAINTAINING YOUR VEHICLE 333 If an examination of your engine compartment shows no • Maintain engine coolant (antifreeze) concentration at evidence of radiator or hose leaks, the vehicle may be 50% HOAT engine coolant (antifreeze) (minimum) safely driven. The vapor will soon dissipate. and distilled water for proper corrosion protection of your engine which contains aluminum components. • Do not overfill the coolant recovery bottle.
334 MAINTAINING YOUR VEHICLE Brake System Fluid Level Check — Brake Master Cylinder The fluid level in the master cylinder should be checked whenever the vehicle is serviced, or immediately if the brake system warning light is on. If necessary, add fluid to bring level to the full mark on the side of the reservoir of the brake master cylinder. Be sure to clean the top of the master cylinder area before removing the cap. With disc brakes, fluid level can be expected to fall as the brake pads wear.
MAINTAINING YOUR VEHICLE 335 WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a accident.
336 MAINTAINING YOUR VEHICLE CAUTION! The fluid level is preset at the factory and does not require adjustment under normal operating conditions. If a transmission fluid leak occurs, visit your authorized dealer immediately. Severe damage to the transmission may occur. Your authorized dealer has the proper tools to accurately adjust the fluid level.
MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your vehicle in the shade using MOPAR威 Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumulated on your vehicle, use MOPAR威 Super Kleen Bug and Tar Remover or equivalent to remove. 337 CAUTION! • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces.
338 MAINTAINING YOUR VEHICLE • If you detect any stone chips or scratches in the paint, Wheel and Wheel Trim Care touch them up immediately. The cost of such repairs is All wheels and wheel trim, especially aluminum and chrome-plated wheels should be cleaned regularly with a considered the responsibility of the owner. mild soap and water to prevent corrosion.
MAINTAINING YOUR VEHICLE 339 • For tough stains, apply MOPAR威 Total Clean or a mild if absolutely necessary. Do not use harsh cleaners or soap solution to a clean, damp cloth and remove the Armor All威. Use MOPAR威 Total Clean or equivalent to stain. Use a fresh, damp towel to remove soap residue. clean vinyl upholstery.
340 MAINTAINING YOUR VEHICLE WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOPAR威 Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters.
MAINTAINING YOUR VEHICLE FUSES Interior Fuses The fuse panel is on the lower instrument panel just to the left of the steering column.
342 MAINTAINING YOUR VEHICLE Cavity 10 11 12 13 Cartridge Fuse MiniFuse 10 Amp Red Description Final Drive Control Module (FDCM), Heater Ventilation/ Air Conditioning (HVAC), Rear Heated Seat Switch, O/H, Heater Ventilation/ Air Conditioning (HVAC) Relay, Rear Park Assist Spare (B+) 10 Amp Door Mods, O/H Red Lamps, IP Courtesy Lamps, Glove Box Lamp (B+) 10 Amp Autowipe (R/A) Red Cavity 14 15 16 17 19 20 Cartridge Fuse MiniFuse 20 Amp Yellow 10 Amp Red 10 Amp Red 15 Amp Blue Spare (R/S) 10 Amp R
MAINTAINING YOUR VEHICLE Cavity 21 22 24 25 Cartridge Fuse MiniFuse Spare (Acc Delay) 15 Amp Blue 10 Amp Red 10 Amp Red Description 343 Underhood Fuses (Power Distribution Center) Rear Wiper (B+) Power Distribution Center (PDC) Relays, Powertrain Control Module, A580 (R/S) Shifter Assy (BTSI), Trans.
344 MAINTAINING YOUR VEHICLE Cavity 2 3 4 5 6 7 8 9 Cartridge Fuse 40 Amp Green 50 Amp Red 30 Amp Pink 50 Amp Red 30 Amp Pink 40 Amp Green 40 Amp Green 20 Amp Blue MiniFuse Description HID Headlamps PTC Heater 2 (Diesel Only) Power Outlets Cavity 10 11 12 13 PTC Heater 3 (Diesel Only) Cig Lighter, Trail Tow Batt Power Liftgate (Commander Only) Starter, JB Power 14 15 16 17 Front Power Windows Cartridge Fuse — 40 Amp Green 30 Amp Pink 40 Amp Green 30 Amp Pink — 50 Amp Red 30 Amp Pink MiniFuse Des
MAINTAINING YOUR VEHICLE Cavity 18 19 20 21 22 23 24 25 Cartridge Fuse 40 Amp Green 40 Amp Green 30 Amp Pink MiniFuse Description Accessory Delay, Seats JB Power Cavity 26 27 Cartridge Fuse MiniFuse 15 Amp Blue 20 Amp Yellow Wiper Motor 28 20 Amp Yellow 20 Amp Yellow 25 Amp Natural 20 Amp Yellow 20 Amp Yellow Fuel Pump 29 TCM, A/C Clutch Power Inverter 30 31 32 Rear Heated Seats 33 Final Drive Control Module (FDCM) 30 Amp Green 20 Amp Yellow — — 15 Amp Blue 20 Amp Yellow 345 Description Brake
346 MAINTAINING YOUR VEHICLE Cavity 34 35 36 37 38 39 40 41 42 Cartridge Fuse MiniFuse — 20 Amp Yellow — 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 25 Amp Natural 20 Amp Yellow — Description Spare Trail-Tow Mod (Export Only) Spare Ignition Switch Cavity 43 44 Cartridge Fuse MiniFuse 25 Amp Natural — Description Coils, Actuators Spare Underhood Fuses (Integrated Power Module) HID Left HID Right Next Generation Controller (NGC), Injectors Subwoofer (SRT Only) Spare Integrated Power Module
MAINTAINING YOUR VEHICLE Cavity 8 9 10 12 13 14 15 16 Cartridge Fuse MiniFuse 10 Amp Red 10 Amp Red 10 Amp Red 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow Description Cavity Lt Park Lamps 17 Trailer-Tow Park Lamps Rt Park Lamps 18 Front Control Module (FCM) Batt #4 Front Control Module (FCM) Batt #2 Adjustable Pedal 20 Cartridge Fuse 19 21 22 30 Amp Pink 23 50 Amp Red Ft Fog Lamps Horn MiniFuse 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow
348 MAINTAINING YOUR VEHICLE Cavity 27 28 29 30 Cartridge Fuse MiniFuse 15 Amp Blue 20 Amp Yellow 10 Amp Red 10 Amp Red Description Ignition Off Draw (IOD) #1 — Intrusion Module, Satellite Video, Steering Control Module Ignition Off Draw (IOD) #2 — Radio Occupant Restraint Controller (ORC) R/S Occupant Restraint Controller (ORC) R/O VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery.
MAINTAINING YOUR VEHICLE 349 REPLACEMENT BULBS Headlamps (Low Beam) . . . . . . . . . . . . . . . . . . . 9006 Headlamps (High Beam) . . . . . . . . . . . . . . . . . . 9005 Interior Lights Bulb Type Rear Turn/Stop/Tail Lamps . . . . . . . . . . . . . . . 3157K Glove Box Lamp . . . . . . . . . . . . . . . . . . . . . . . . . 194 NOTE: Numbers refer to commercial bulb types that Grab Handle Lamp . . . . . . . . . . . . . . . . L002825W5W can be purchased from your authorized dealer.
350 MAINTAINING YOUR VEHICLE WARNING! A transient high tension occurs at the bulb sockets of High Intensity Discharge (HID) headlamps when the headlamp switch is turned ON. It may cause serious electrical shock or electrocution if not serviced properly. See your authorized dealer for service. NOTE: On vehicles equipped with High Intensity Discharge (HID) headlamps, when the headlamps are turned on, there is a blue hue to the lamps.
MAINTAINING YOUR VEHICLE 351 CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front Turn Signal 1. Open the hood. 2. Turn the turn signal bulb one–quarter turn counterclockwise to remove from housing. 1 — High Beam Bulb 2 — Low Beam Bulb 3 — Turn Signal Bulb 3. Disconnect the electrical connector and replace the bulb.
352 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front Fog Lamp Rear Tail, Stop, Turn Signal, And Backup Lamps 1.
MAINTAINING YOUR VEHICLE 3. Squeeze the socket assembly tabs to remove it from the housing. 1 — Tail/Stop Lamp Bulb 2 — Tail/Turn Signal Bulb 353 3 — Back-Up Lamp Bulb 4. Pull the bulb to remove it from the socket. 5. Replace the bulb, reinstall the socket, and reattach the lamp assembly.
354 MAINTAINING YOUR VEHICLE Center High-Mounted Stop Lamp (CHMSL) 1. Remove the two screws securing the CHMSL. 2. Twist the bulb socket to remove from the CHMSL housing. 3. Pull the bulb out of the socket. 4. Replace the bulb, reinstall the socket and reattach the CHMSL.
MAINTAINING YOUR VEHICLE 355 FLUID CAPACITIES Fuel (Approximate) Engine Oil with Filter 6.1 Liter Engine (SAE 5W-40, API Certified) Cooling System * 6.1 Liter Engine (MOPAR威 Engine Coolant/Antifreeze 5 Year/100,000 Mile Formula or equivalent) * Includes heater and coolant recovery bottle filled to MAX level. U.S. 21 Gallons Metric 79 Liters 7 Quarts 6.6 Liters 14.
356 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Fuel Selection Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent.
MAINTAINING YOUR VEHICLE 357 Chassis Component Automatic Transmission Transfer Case Axle Differential (Front-Rear) Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product. MOPAR威 NV146 Transfer Case Fluid or equivalent. Usage of other fluid/ lubricants is NOT recommended. MOPAR威 Synthetic Gear & Axle Lubricant SAE 75W-140 (API-GL5) or equivalent. MOPAR威 DOT 3 Brake Fluid, SAE J1703 should be used.
M A I N T E N A N C ▫ Required Maintenance Intervals . . . . . . . . . . 362 E MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . 360 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 360 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. 361 M A accuracy of the oil level reading. Add oil only when I N the level is at or below the ADD or MIN mark. • Under no circumstances should oil change intervals • Check the windshield washer solvent and add if exceed 6,000 miles (10,000 km) or 6 months, whichever required. comes first.
M A I N T E N A N C E S C H E D U L E S 8 362 MAINTENANCE SCHEDULES At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines. CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle. Required Maintenance Intervals Refer to the Maintenance Schedules on the following pages for the required maintenance intervals.
MAINTENANCE SCHEDULES 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 363 M 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
M 364 MAINTENANCE SCHEDULES A I 18,000 Miles (30,000 km) or N T 18 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N C E 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings, replace if necessary. ❏ Inspect the CV joints.
MAINTENANCE SCHEDULES 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule 42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Replace the engine air cleaner filter. ❏ Drain the transfer case and refill. ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ Change the engine oil and engine oil filter.
M 366 MAINTENANCE SCHEDULES A I 48,000 Miles (80,000 km) or 48 Months Maintenance Service N T Schedule E ❏ Change the engine oil and engine oil filter. N ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. A N ❏ Inspect the brake linings; replace if necessary. C ❏ Inspect the CV joints. E ❏ Inspect exhaust system.
MAINTENANCE SCHEDULES 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Replace the engine air cleaner filter. Inspect the brake linings; replace if necessary. Adjust parking brake on vehicles equipped with four-wheel disc brakes. Change the automatic transmission fluid and filter(s) if using your vehicle for any of the following: police, taxi, fleet, or frequent trailer towing. Drain the transfer case and refill.
M 368 MAINTENANCE SCHEDULES A I 72,000 Miles (120,000 km) or 72 Months Maintenance Service N T Schedule E ❏ Change the engine oil and engine oil filter. N ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. A N ❏ Inspect the brake linings; replace if necessary. C ❏ Inspect the CV joints. E ❏ Inspect exhaust system.
MAINTENANCE SCHEDULES 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule 90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary.
M 370 MAINTENANCE SCHEDULES A I 96,000 Miles (160,000 km) or 96 Months Maintenance Service N T Schedule E ❏ Change the engine oil and engine oil filter. N ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. A N ❏ Inspect the brake linings; replace if necessary. C ❏ Inspect the CV joints. E ❏ Inspect exhaust system.
MAINTENANCE SCHEDULES 108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule 114,000 Miles (190,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary.
M 372 MAINTENANCE SCHEDULES A I 120,000 Miles (200,000 km) or 120 Months Maintenance Service N T Schedule E ❏ Change the engine oil and engine oil filter. N ❏ Replace the engine air cleaner filter. A ❏ Inspect the brake linings; replace if necessary. N ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. C ❏ Inspect the CV joints. E ❏ Inspect exhaust system.
MAINTENANCE SCHEDULES 132,000 Miles (220,000 km) or 132 Months Maintenance Service Schedule 138,000 Miles (230,000 km) or 138 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary.
M 374 MAINTENANCE SCHEDULES A I 144,000 Miles (240,000 km) or 144 Months Maintenance Service N T Schedule E ❏ Change the engine oil and engine oil filter. N ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. A N ❏ Inspect the brake linings; replace if necessary. C ❏ Inspect the CV joints. E ❏ Inspect exhaust system.
MAINTENANCE SCHEDULES † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 381 ▫ Prepare For The Appointment . . . . . . . . . . . 379 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 381 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 379 䡵 Warranty Information (U.S. Vehicles Only) . . . .
378 IF YOU NEED CONSUMER ASSISTANCE 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 385 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 385 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 385 ▫ Temperature Grades . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 379 the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the for an appointment. right papers with you. Take your warranty folder. All work to be performed may not be covered by the IF YOU NEED ASSISTANCE warranty.
380 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized • Vehicle delivery date and mileage dealer’s service manager first. Most matters can be reChrysler Group LLC Customer Center solved with this process. P.O. Box 21–8004 • If for some reason you are still not satisfied, talk to the Auburn Hills, MI 48321–8004 general manager or owner of the authorized dealer- Phone: (800) 992-1997 ship. They want to know if you need assistance. Chrysler Canada Inc.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
382 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns.
IF YOU NEED CONSUMER ASSISTANCE 383 If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. In Canada If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately.
384 IF YOU NEED CONSUMER ASSISTANCE These comprehensive Service Manuals provide the • Owner’s Manuals information that students and professional technicians These Owner’s Manuals have been prepared with the need in diagnosing/troubleshooting, problem solving, assistance of service and engineering specialists to maintaining, servicing, and repairing Chrysler Group acquaint you with specific Chrysler Group LLC veLLC vehicles. A complete working knowledge of the hicles.
IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle. 385 significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.
386 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
388 INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . 159,252 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 330 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 287 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 285 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . . 114 Air Conditioner Maintenance . . . . . . . . . . . . . . . 322 Air Conditioning, Operating Tips . . . . . . . . . . . . 232 Air Conditioning Refrigerant . . . . . . . . .
INDEX Keyless Transmitter Replacement (RKE) . . . . . . . 22 Saving Feature (Protection) . . . . . . . . . . . . . . . 104 Belts, Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36,72 Body Mechanism Lubrication . . . . . . . . . . . . . . . 323 B-Pillar Location . . . . . . . . . . . . . . . . . . . . . . . . 268 Brake Assist System . . . . . . . . . . . . . . . . . . . . . . 256 Brake Control System, Electronic . . . . . . . . . . . . . 255 Brake System . . . . . . . . . . . . . . . . . . . .
390 INDEX Check Engine Light (Malfunction Indicator Light) . . . . . . . . . . . . . . . 315 Checking Your Vehicle For Safety . . . . . . . . . . . . . 71 Checks, Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Child Restraint . . . . . . . . . . . . . . . . . . . . 60,61,66,68 Child Restraint Tether Anchors . . . . . . . . . . . . . 65,66 Child Safety Locks . . . . . . . . . . . . . . . . . . . . . . . . 28 Clean Air Gasoline . . . . . . . . . . . . . . . . . . . . . . .
INDEX Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . . . 317 Defroster, Rear Window . . . . . . . . . . . . . . . . . . . 149 Defroster, Windshield . . . . . . . . . . . . . . . . . . . 73,230 Diagnostic System, Onboard . . . . . . . . . . . . . . . . 314 Dimmer Switch, Headlight . . . . . . . . . . . . . . . . . 106 Dipsticks Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 249 Disabled Vehicle Towing . . . . . . . . . . . . . . . . . . . 309 Disarming, Theft System . . . . .
392 INDEX Checking Oil Level . . . . . . . . . . . . . . . . . . . . . 318 Compartment . . . . . . . . . . . . . . . . . . . . . . . . . 313 Compartment Identification . . . . . . . . . . . . . . . 313 Coolant (Antifreeze) . . . . . . . . . . . . . . . . . . . . 328 Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328 Exhaust Gas Caution . . . . . . . . . . . . . . . . . . 71,286 Fails to Start . . . . . . . . . . . . . . . . . . . . . . . . . . 239 Flooded, Starting . . . . . . . . . . .
INDEX Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Fluid Level Checks Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334 Cooling System . . . . . . . . . . . . . . . . . . . . . . . 328 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 318 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 249 Fluids, Lubricants and Genuine Parts . . . . . . . . . . 356 Fog Light Service . . . . . . . . . . . . . . . . . . . . . . . .
394 INDEX . . . . 243 17,23,282 . . . . 340 . . . . 290 . . . . 289 Hitches Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 292 Holder, Cup . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 HomeLink威 (Garage Door Opener) Transmitter . . . 128 Hood Release . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 Hands-Free Phone (Uconnect™) . . . . . . . . . . . . . . 83 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . . 302 Head Restraints . . . . . . . . . . . . . . . .
INDEX Interior Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . 341 Interior Lighting . . . . . . . . . . . . . . . . . . . . . . . . 107 Interior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 107 Intermittent Wipers (Delay Wipers) . . . . . . . . . . . 110 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Inverter, Power . . . . . . . . . . . . . . . . . . . . . . . . . 140 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . . 304 Key, Programming .
396 INDEX Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 349 Cargo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 Center Mounted Stop . . . . . . . . . . . . . . . . . . . 354 Cruise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 Daytime Running . . . . . . . . . . . . . . . . . . . . . . 103 Dimmer Switch, Headlight . . . . . . . . . . . . . 100,106 Electronic Stability Program (ESP) Indicator . . . . . . . . . . . . . . . . . . . . . . .
INDEX Vanity Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 Load Floor, Cargo . . . . . . . . . . . . . . . . . . . . . . . 147 Loading Vehicle Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268 Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Automatic Door . . . . . . . . . . . . . . . . . . . . . . . . 28 Child Protection . . . . . . . . . . . . . . . . . . . . . . . .
398 INDEX Multi-Function Control Lever . . . . . . . . . . . . . . . 100 New Vehicle Break-In Period . . . . . . . . . . . . . . . . 70 Occupant Restraints . . . . . . . . . . . . . . . . . . . 34,51,55 Occupant Restraints (Sedan) . . . . . . . . . . . . . 48,51,54 Octane Rating, Gasoline (Fuel) . . . . . . . . . . . . . . 282 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . 163,164 Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 Oil, Engine . . . . . . . . . . . . . .
INDEX Phone, Cellular . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Phone, Hands-Free (Uconnect™) . . . . . . . . . . . . . . 83 Placard, Tire and Loading Information . . . . . . . . . 268 Polishing and Waxing . . . . . . . . . . . . . . . . . . . . . 337 Power Distribution Center (Fuses) . . . . . . . . . . . . . . . 343 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 Mirrors . . . . . . . . . . . . . . . .
400 INDEX Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323 Reminder, Lights On . . . . . . . . . . . . . . . . . . . . . 104 Reminder, Seat Belt . . . . . . . . . . . . . . . . . . . . . . . 43 Remote Control Starting System . . . . . . . . . . . . . . . . . . . . . . . . 24 Remote Keyless Entry (RKE) . . . . . . . . . . . . . . . . . 19 Remote Sound System (Radio) Controls . . . . . . . . 223 Remote Starting System . . . . . . . . . . . . . . . . . . . . 24 Replacement Bulbs . . .
INDEX Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 340 Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 Shoulder Belt Anchorage . . . . . . . . . . . . . . . . . 41 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339 Easy Entry . . . . . . . . .
402 INDEX Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24,238 Automatic Transmission . . . . . . . . . . . . . . . . . 238 Cold Weather . . . . . . . . . . . . . . . . . . . . . . . . . 239 Engine Fails to Start . . . . . . . . . . . . . . . . . . . . 239 Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Steering Power . . . . . . . . . . . . . . . . . . . . . . . . . . . 248,249 Tilt Column . .
INDEX Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73,272,385 Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 274 General Information . . . . . . . . . . . . . . . . . . . . 272 High Speed . . . . . . . . . . . . . . . . . . . . . . . . . . 275 Inflation Pressures . . . . . . . . . . . . . . . . . . . . . 274 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 277 Load Capacity . . . . . . . . . . . . . . . . . . . . . 268,269 Pressure Monitor System (TPMS) .
404 INDEX Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240 Transmitter Battery Service (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 22 Transmitter, Garage Door Opener (HomeLink威) . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 Transmitter Programming (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 19 Transmitter, Remote Keyless Entry (RKE) . . . . . . . . 19 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . 276 Turn Signals . . .
Window Fogging . . . . . . . . . . . . . . . . . . . . . . . . 232 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Windshield Defroster . . . . . . . . . . . . . . . . . . . 73,230 Windshield Washers . . . . . . . . . . . . . . . . . . . . . . 109 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324 Windshield Wiper Blades Windshield Wipers . . . . .
Chrysler Group LLC 10WK742-126-AB 2nd Edition Printed in U.S.A.
