SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your Crossfire. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 9 ▫ Start Lockout . . . . . . . . . . . . . . . . . . . . . . . . .14 ▫ Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 䡵 Remote Keyless Entry . . . . . . . . . . . . . . . . . . . .14 ▫ Obtaining Replacement Keys . . . . . . . . . . . . . .10 ▫ To Unlock The Doors . . . . . . . . . . . . . . . . . . .14 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Opening The Decklid During Top Operation . . .20 ▫ Supplemental Restraint System (SRS) - Airbag . .29 䡵 Power Windows . . . . . . . . . . . . . . . . . . . . . . . .21 ▫ Child Restraint . . . . . . . . . . . . . . . . . . . . . . . .39 ▫ Power Window Operation With The Convertible Top Switch (Roadster Only) . . . . . .22 䡵 Engine Break-In Recommendations . . . . . . . . . .46 䡵 Rear Liftgate/Decklid Release . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9 A WORD ABOUT YOUR KEYS You can insert the double-sided keys into the locks with either side up. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys only from an authorized dealer. Ask your dealer for these numbers and keep them in a safe place. CAUTION! An unlocked car is an invitation to thieves.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Obtaining Replacement Keys Your vehicle is equipped with a theft deterrent locking system requiring a special key manufacturing process. For security reasons, replacement keys can only be obtained from your authorized dealer. Important! Removing the key from the steering lock activates the start lock-out. The engine cannot be started. Turning the key in the steering lock to the ON/RUN position deactivates the start lock-out.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 GLOVE COMPARTMENT LOCK The glove compartment can be locked by turning the key straight up to the vertical or right position, and then removing the key. To unlock the glove compartment, turn the key to the horizontal or left position, and then remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The doors can be unlocked by pulling on the inside door handle, pressing and releasing the top portion of the central locking switch located in the console, or by pressing and releasing the Unlock transmit button on the key fob. Both doors can also be unlocked by turning the key counterclockwise in the driver’s door. NOTE: In case of a malfunction in the central locking system, the doors can be locked and unlocked individually.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 was previously locked with the central locking switch, the complete vehicle is unlocked when a door is opened from the inside. locking feature and neither door is opened, the doors remain unlocked even at vehicle speeds of approximately 9 mph (15 km/h) or more. NOTE: The fuel filler door and center console (roadster only) cannot be locked or unlocked with the central locking switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Make sure that the hood, rear liftgate/decklid and door switches are in adjustment. Perform the quick system check which follows: Use the remote transmitter to set the alarm. If the parking lamps flash three times, the system is operating properly. If not, there is a problem with a switch or the system. See your authorized dealer for service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 If the vehicle cannot be locked or unlocked by pressing the transmit button, then it may be necessary to change the batteries in the remote control. To Lock The Doors: Press the Lock button on the key fob once. All turn signal lights blink three times to indicate that the vehicle is locked. If the turn signal lights do not blink, a door or rear liftgate/decklid is not closed properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Use the Panic Alarm: Press and hold the Panic button to activate the alarm. Press and hold the Panic button or unlock the door with the key to deactivate the alarm. The alarm will also shut off after three minutes or when vehicle speed reaches 15 mph (24 km/h). 2. This device must accept any interference that may be received, including interference that may cause undesired operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 • Remove the old batteries. approximately 30 seconds, insert the key in the ignition and turn it to the ON/RUN position. The remote control should once again be operational. SECURITY ALARM SYSTEM The system monitors the doors, rear liftgate/decklid, hood, and ignition for unauthorized operation. The security alarm system is automatically armed or disarmed with the remote control or any of your vehicle’s keys by locking or unlocking the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tow-Away Alarm The tow-away alarm switch is located on the console. To deactivate for towing or jacking up the vehicle, press and release the upper portion of the switch. Press and release the upper portion to activate it again. After the alarm system has been armed, the exterior vehicle lights will flash and an alarm will sound when someone attempts to raise the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 DECKLID INTERNAL EMERGENCY RELEASE ROADSTER As a security measure, a Decklid Internal Emergency Release lever is built into the decklid latching mechanism. In the event of an individual being locked inside the trunk, the decklid can be easily opened by pulling on the glow-in-the-dark handle attached to the decklid latching mechanism. See picture. WARNING! Do not allow children to have access to the trunk by climbing into the trunk from outside.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! It is possible for the decklid to contact the tonneau cover if opened during the top operation. CAUTION! The tops hydraulic pressure will also be released during this procedure which will allow the top and tonneau cover to slowly collapse. Opening the Decklid During Top Operation The decklid can be opened during the top operation by following this procedure. 1. Turn the ignition “ON”. 2. Push down and hold the convertible top switch. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 POWER WINDOWS The power window switches are located in the console. To operate, turn the key in the ignition switch to the ACC or ON/RUN position. Press the switch in to the resistance point to open; release the switch when the window is in the desired position. 2 For express opening of windows, press the switch past the resistance point and release; the window lowers to the fully open position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Window Operation With The Convertible Top Switch (Roadster Only) The power windows can also be operated by using the convertible top switch. To operate, turn the key in the ignition switch to the ON/RUN position. Press down on the rear of the convertible top switch twice to open the windows. Press down on the front of the convertible top switch twice to close the windows.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Please pay close attention to the information in this section. It tells you how to use your restraint system properly to keep you and your passengers as safe as possible. WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other occupants, or you can be thrown out of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In cases of other frontal impacts, rollovers, certain side impacts, rear collisions or other accidents without sufficient frontal or rear impact forces, the emergency tensioning retractors will not be activated. The driver and passenger will then be protected by the fastened seat belts and inertia reel in the usual manner. WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up a little on the shoulder belt, as shown. 5. To loosen the lap belt if it is too tight, tilt the latch plate away from you and pull on the lap belt. Remember that a snug belt reduces the risk of sliding under the belt in a collision. 6. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 WARNING! WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is very dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 Supplemental Restraint System (SRS) - Airbag The vehicle is also equipped with side airbags, located in the driver and passenger doors. Side airbags also work with seat belts to improve occupant protection. WARNING! This vehicle has airbags for the driver and passenger as a supplement to the seat belt restraint systems. The driver’s airbag is mounted in the steering wheel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The seat belts are designed to protect you in many types of collisions. The front airbags deploy only in moderate to severe front collisions. In certain types of collisions, both the front and side airbags may be triggered. But even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during airbag deployment could cause serious injury. • Airbags need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE These include all of the items listed above except the knee bolster, the instrument panel, and the steering wheel and column. • The Occupant Restraint Controller also turns on the AIRBAG light in the instrument panel for four seconds when the ignition is first turned on, then turns the light off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 • The knee impact bolster helps protect the knees and working with the seat belts, position you for the best interaction with the airbags. The airbag system is designed to deploy when the impact sensors detect a moderate-to-severe frontal collision, to help restrain the driver and passenger, and then to immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • As the airbags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic nitrogen gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers are designed to open only when the airbags are inflated. • Do not attach cup holders or any other objects on or around the door. The inflating side airbag could drive the objects into occupants, causing serious injury.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • The door mounted side airbag deploys with considerable force. Being too close to the door panel during airbag deployment could cause serious injury or death. • All occupants must be in the appropriate restraint for their size and age, especially children 12 and under. • To help avoid the potential for serious injury and death should the side airbag be activated, please follow these guidelines: 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 If the airbag is turned off when there is any other occupant at that position, the supplemental restraint provided by the airbag will not be available. To turn OFF the passenger front airbag, use the on/off switch located on the instrument panel. NOTE: When the passenger airbag is turned off, the yellow airbag off light will illuminate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Shut Off the Passenger Airbag: To Turn On the Passenger Airbag: • Place the ignition key in the on/off switch, turn the key clockwise, and remove the key from the switch. This will shut off the passenger front airbag. • Place the ignition key in the on/off switch, turn the key counterclockwise, and remove the key from the switch. This will turn on the passenger airbag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbag is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the airbag covers. Do not modify the front bumper or vehicle body structure. • You need proper knee impact protection in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 WARNING! • A rearward facing infant restraint must not be used unless the passenger airbag has been shut off. A rearward facing infant restraint may be struck by a deploying passenger airbag which may cause severe or fatal injury to the infant. • Improper installation can lead to failure of a child restraint. It could come loose in a collision. The child could be badly injured or killed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system. (See LATCH - Child Seat Anchorage System section.) The belt-positioning booster seat is for children weighing more than 40 lbs. (18 kg), but who are still too small to fit the vehicle’s seat belts properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 are general instructions, and not all child restraint systems will be installed exactly as described here. Again, carefully follow the installation instructions that were provided with the child restraint system. The passenger seat tether anchorage is located on the back of the seat cushion frame. It is visible by moving the passenger seat forward in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap. You will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchorages. Next, you can attach the tether strap to the anchor by moving the passenger seat forward.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 retractor action is restored. Any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary. If your child restraint is equipped with a tether strap, attach it to the vehicle by first moving the seat back fully forward. Next, route the child restraint tether directly over the top of the seat, through the strap near the top of the seat back, and attach the hook to the anchor bar.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor position directly behind the child seat to secure a child restraint top tether strap. Transporting Pets Deploying airbags could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Adjust the heating or cooling system to force outside air into the vehicle. Set the blower at high speed. SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defrosters Check operation by pressing the A/C control button, selecting the defrost mode and placing the blower control on high speed. You should be able to feel the air directed against the windshield. Periodic Safety Checks You Should Make Outside the Vehicle Tires Examine tires for excessive tread wear or uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect for tread cuts or sidewall cracks.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Convertible Top Operation . . . . . . . . . . . . . . . .52 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 ▫ To Lower The Top . . . . . . . . . . . . . . . . . . . . . .53 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .66 ▫ To Raise The Top . . . . . . . . . . . . . . . . . . . . . .57 ▫ Exterior Mirrors Folding Feature . . . . . . . . . . .67 ▫ Convertible Top Lamp And Audible Signal Chart . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 To Open And Close The Hood . . . . . . . . . . . . .71 ▫ Mist Function . . . . . . . . . . . . . . . . . . . . . . . . .78 䡵 Interior Lights . . . . . . . . . . . . . . . . . . . . . . . . .72 䡵 Telescoping Steering Column . . . . . . . . . . . . . .79 ▫ Front Map/Reading Lights . . . . . . . . . . . . . . .73 䡵 Tire Pressure Monitor System . . . . . . . . . . . . . .80 ▫ Battery Saver Feature . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 51 ▫ Reprogramming a Single Button . . . . . . . . . . . .93 䡵 Umbrella Hook . . . . . . . . . . . . . . . . . . . . . . . .94 ▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONVERTIBLE TOP OPERATION WARNING! The convertible top does not provide the structural protection that a reinforced metal roof does and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision. Therefore, it is important that all occupants wear their seat belts at all times when riding in a convertible.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 53 CAUTION! When opening and closing the convertible top, make sure that: • There is sufficient clearance of at least 6 ft. (1.8m) for the convertible top to move up. • Nothing is placed on the tonneau cover. • The outside temperature is above 32°F (0°C). Otherwise the convertible top and other parts of the vehicle could be damaged. CAUTION! Use caution when putting items into the storage compartment with the top in the closed position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! To avoid possible damage to the tonneau cover and convertible top, do not allow the convertible top to remain in the suspended position. After approximately 10 minutes in the suspended position an audible beep will be heard and the hydraulic pressure will be released which will allow the top and the tonneau cover to lower. The convertible top switch can be pressed to cancel this operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 55 2. Make sure the decklid is closed. 3. Turn the ignition key to the ON/RUN position. CAUTION! Be sure to turn the ignition to the “ON/RUN” position before releasing the top from the windshield header. The windows will not go down if the top is released from the header without the ignition turned “ON”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Once the release handle is rotated, the windows will automatically go down. 5. Push up on the convertible top latch handle to create a gap between the header and top of approximately 8 inches (200 mm). As soon as the top is free, rotate the latch handle counterclockwise just over one quarter turn and push it up into the stored position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 57 NOTE: Once the top is lowered and the audible signal is heard, you can continue to push the convertible top switch down or push it within 2 seconds to raise the windows. The windows can also be closed/opened later using the power window switches. CAUTION! To prevent mildew, the convertible top must be dry before lowering it into the storage compartment. Do not lower a frozen convertible top until thawed and dry.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Turn the ignition key to the ON/RUN position and press down on the front of the convertible top switch. NOTE: If the top is latched to the windshield header before the rear of the top is properly latched, an audible warning will sound. 5. Push the latch handle release button, pull the latch handle down from the storage position and turn it clockwise just over one quarter turn. 6.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 59 7. When the top engages to the header, turn the latch handle counterclockwise just over one quarter turn to the lock position and push the latch handle up to the stored position. The top is now secured in the closed position. NOTE: The convertible top switch indicator will light up and an audible warning will be heard if you start driving the vehicle without the top fully locked in the closed position. 8.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Once the cargo compartment divider is folded forward to increase the cargo compartment capacity, the tonneau cover flaps are exposed and can be damaged by long items being put into the cargo compartment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 61 Convertible Top Lamp and Audible Signal Chart Below is a table containing all of the visual and audible signals that can be seen or heard during top operation or if a fault is present.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES The console has a power outlet/cigar lighter, an ash tray with a coin holder, a cupholder, and the passenger airbag light. In addition, there are switches to control the heated seats, electronic stability program (ESP), hazard flashers, central locking, rear defroster and towing alarm.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 63 A cargo net for storage is located in the footwell area on the passenger side. WARNING! Keep compartment lids closed. This will help to prevent stored objects from being thrown about and injuring vehicle occupants during an accident. Ashtray Lightly touch the bottom of the ashtray cover. The ashtray will open automatically. To remove the ashtray insert, pull the ashtray past the detent. Hold both sides of the insert, and pull up.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Remove the ashtray only with the vehicle stopped and the ignition off. Otherwise, the vehicle might move unexpectedly as a result of unintended contact with the gear selector lever. Coin Holder With the ashtray open, folding down the cover plate reveals the coin holder, which can accommodate nine coins in various sizes up to a U.S. quarter.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65 Power Outlet/Cigar Lighter The dual-purpose power outlet is located in the console, next to the passenger airbag off warning light. The power outlet can accommodate a lighter or electrical accessories up to a maximum of 15 amps. The outlet is protected by a 15 amp fuse, located behind the fuse cover on the left end of the instrument panel. The lighter will operate only when the ignition switch is in the ON/ACC position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The cupholder is designed to hold beverage containers up to 20 oz. (1 L). MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical mirror adjustment. CAUTION! Only use containers that fit into the cupholder. Overfilled containers could spill during vehicle maneuvers.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 Exterior Mirrors Folding Feature All exterior mirrors are hinged to move forward or rearward to resist damage. The hinges have three detent positions: full forward, full rearward, and normal. Heated Remote Control Mirrors Both outside mirrors are heated to melt frost or ice when the Rear Window Defroster switch is depressed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Remote Control Outside Mirrors The mirrors can be adjusted by using the remote control located in the console. Rotate the switch to the right to select the right mirror, rotate to the left to select the left mirror. Then use the switch to adjust the selected mirror to the desired direction.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 Vanity Mirrors SEATS Driver Eight-Way Power Seat The switches to adjust the power seats are located on the outboard side of each seat. The driver’s seat features eight-way power adjustment - horizontal, vertical, cushion tilt and back angle. A vanity mirror is on each sun visor. To use the mirror, rotate the sun visor down and slide open the mirror cover.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Passenger Four-Way Power Seat The switches to adjust the passenger seat are also on the outboard side of the seat. The passenger seat provides four-way adjustment - horizontal and back angle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 Heated Seats This feature heats the driver and passenger seats. The controls for the heated seats are located on the instrument panel, below the radio. TO OPEN AND CLOSE THE HOOD To open the hood, pull the release lever located inside your vehicle, below the instrument panel. 3 After turning the ignition switch ON, you can choose the HI, LO, or OFF setting. Indicators on the switches show which setting has been selected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To prevent possible damage, close the hood by dropping it from approximately 12 inches (30 cm). WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving, and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. INTERIOR LIGHTS A two-position mode selector switch controls the interior lights located in the overhead console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 Front Map/Reading Lights These lights are located between the sun visors. A single centrally located switch operates both lights. Instrument Panel Lighting With the parking lights or headlights on, rotate the dimmer control to the left of the speedometer to increase or decrease brightness of the instrument panel. 3 Battery Saver Feature To prevent battery drain if a door is left open or ajar, the interior lights will turn off automatically after 15 minutes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE EXTERIOR LIGHTS Headlights and Parking Lights When the headlight switch is turned clockwise from OFF to the first position, the parking lights, taillights, side marker lights, license plate lights and instrument panel lights are all illuminated. Lights-On Reminder If the headlights or parking lights are left on after the ignition is turned off, a warning will sound if the driver’s door is opened.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 Standing Lights When the vehicle is parked on the street, the standing lights (left or right side parking lights) can be turned on, making your vehicle more visible to passing vehicles. MULTIFUNCTION CONTROL LEVER To operate the standing lights, turn the headlight switch counterclockwise one stop (right lamps) or two stops (left lamps) from the OFF position. To turn off the standing lights, return the headlight switch to the OFF position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To operate the turn signals continuously, move the control lever up or down past the point of resistance. The operation is automatically canceled when the steering wheel is turned to a large enough degree. If one of the turn signal lights fail, the turn signal indicator system flashes and sounds at a faster than normal rate. If an indicator fails to light when the control lever is moved, it may mean that the fuse or indicator bulb is defective.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 Passing Light You can signal another vehicle with your headlights by lightly pulling the multifunction control lever toward the steering wheel. This will cause the headlights to turn on at high beam and remain on until the control lever is released. Windshield Wipers And Washer The wipers and washer are operated by a switch in the multifunction control lever. Turn the end of the lever to select desired wiper speed: off, intermittent, normal, or fast.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Push the end of the lever inward and hold it to activate the wiper and washer together. WARNING! Mist Function Push the end of the multifunction control lever inward briefly for a single wipe without adding washer fluid. Use this feature only when the windshield is wet. Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 TELESCOPING STEERING COLUMN Unlock the steering column by pulling out the handle located directly below the column. The indicator light located in the instrument cluster will come on. To lengthen or shorten the steering column, pull out or push in the steering wheel. Lock the steering column in position by pushing the handle in until it engages. The indicator light in the instrument cluster will go out. WARNING! Do not adjust the steering wheel while driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TIRE PRESSURE MONITOR SYSTEM The Tire Pressure Monitor (TPM) system uses wireless technology to monitor tire pressure levels. Sensors mounted to each wheel as part of the valve stem transmit tire pressure readings to a receiver located inside the vehicle. NOTE: The TPM system can inform you about a low tire pressure condition, but it does not replace normal tire maintenance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 NOTE: The standard TIREFIT system (refer to What To Do In Emergencies for more information) is specifically designed to operate in conjunction with the TPM system, and will not damage the sensors. If your tire pressure is low, you should correct your tire inflation pressure as soon as possible and inspect all of your tires. Low tire pressure will cause the tire pressure light to illuminate and the alert will sound.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Changes and modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. BRAKE ASSIST SYSTEM (BAS) WARNING! BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 The malfunction indicator lamp for the Electronic Stability Program is combined with the BAS. The yellow BAS/ESP malfunction indicator light in the instrument cluster and the yellow ESP warning light in the speedometer dial come on with the key in the ignition switch turned to the ON/RUN position. They should go out with the engine running.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The ESP system corrects for over/understeering of the vehicle by applying brakes to the appropriate wheel. Engine torque is also limited. The ESP warning light, located in the instrument cluster, starts to flash as soon as the tires lose traction and the wheels begin to spin. To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, switch off the ESP system by pressing the upper half of the ESP switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 If the ESP warning light begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. When the ESP warning light is illuminated continuously, the ESP is switched off. To return to the enhanced vehicle stability offered by ESP, press the lower half of the switch (the ESP warning light in the speedometer dial goes out).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL The electronic speed control automatically maintains the set speed by actively regulating the throttle setting. Any speed above approximately 20 mph (30 km/h) can be maintained with the electronic speed control by operating the lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 To accelerate and set a speed, lift the lever up. Lift and hold the lever to accelerate, or lift and release to set a speed. To decelerate and set a speed, press the lever down. Press down and hold the lever to decelerate, or press down and release to set a speed. WARNING! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate A soft tap on the brake pedal, or normal brake pressure while slowing the vehicle, will deactivate the speed control without erasing the memory. Pushing the speed control lever forward or turning the key in the ignition switch to the OFF/LOCK position will turn off the speed control and erase the memory. To Resume Speed To resume a previously set speed, pull the speed control lever toward you, and then release.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 Using Speed Control On Hills Your vehicle is equipped with interactive speed control. This feature activates when driving up or down hills with the speed control engaged and the driver’s foot off the accelerator. WARNING! Speed control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature, as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features, as it could cause injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 NOTE: Step 3 does not have to be followed to program additional hand-held transmitters. 4. Choose one of the three buttons to program. Place the hand-held controller 1–3 inches (25–76 mm) from the universal transceiver while keeping its indicator light in view. NOTE: Some gate operators and garage door openers may require you to replace this Programming Step 5 with procedures noted in the “Gate Operator/Canadian Programming” section. 6.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming Steps 8-10 to complete programming of a rolling code equipped device (most commonly a garage door opener). 8. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 9. Firmly press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 signal has successfully been accepted by the universal transmitter. (The indicator light will flash slowly and then rapidly.) Proceed with Programming Step 6 to complete. Using the Universal Transceiver To operate the universal transceiver, simply press and release the programmed button. Activation will now occur for the programmed device (i.e. garage door opener, gate operator, security system, entry door lock, home/ office lighting, etc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. HomeLink威 is a trademark owned by Johnson Controls, Inc. UMBRELLA HOOK Your Crossfire is equipped with an umbrella hook. This feature is located behind and between the two seats, just above the map pocket.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instruments And Controls . . . . . . . . . . . . . . . . .96 ▫ Driver – L/R . . . . . . . . . . . . . . . . . . . . . . . . 118 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . .97 ▫ Telephone Mute Characteristics . . . . . . . . . . . 118 䡵 Instrument Cluster Description . . . . . . . . . . . . .98 䡵 Compact Disc Maintenance . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENTS AND CONTROLS
UNDERSTANDING YOUR INSTRUMENT PANEL 97 INSTRUMENT CLUSTER The instrument cluster displays are activated by either opening the door, pressing the left button within the cluster, or turning the key in the ignition switch to the ON/RUN position.
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Low Windshield Washer System Fluid Level Warning Light With the key in the ignition switch turned to the ON/RUN position, the indicator light comes on. It should go out when the engine is running. If the indicator light does not go out after starting the engine, or if it comes on while driving, the fluid reservoir is less than 1⁄4 filled.
UNDERSTANDING YOUR INSTRUMENT PANEL 99 CAUTION! level in the reservoir or the coolant temperature is too high (see the Temperature gauge section). The TPM system is designed to monitor your tire pressure and will not function as a tire pressure gauge. After adjusting the air pressure in a tire, there will be a delay before the system updates the display. To check the coolant level, the vehicle must be parked on level ground and the engine stopped. Check coolant level only when the coolant is cold.
UNDERSTANDING YOUR INSTRUMENT PANEL If the pointer rises to the red (Hot) area, stop the vehicle and turn off the engine until the problem is corrected. CAUTION! Continuing to drive with an overheated engine cooling system can cause damage to the engine or other components. 5. Fuel Gauge When the ignition is in the ON/RUN position, the pointer will show the level of fuel remaining in the tank.
UNDERSTANDING YOUR INSTRUMENT PANEL 101 9. Tachometer This gauge shows engine speed in revolutions-perminute (RPM) times 1,000. The red markings on the tachometer indicate excessive engine speed. Ease off on the accelerator before reaching the red area. 10. Brake System Warning Light The dual brake system provides a reserve braking capability if a failure occurs in a portion of the hydraulic system. This light monitors both the brake fluid level and the parking brake.
UNDERSTANDING YOUR INSTRUMENT PANEL 11. Light Outage Indicator With the key in the ignition switch turned to the ON/RUN position, an indicator light comes on. It should go out when the engine is running. If the indicator light does not go out after starting the engine, or if it comes on while driving, it indicates a failure in the parking light, taillight, stoplight, or low beam headlight. The indicator light will come on when the exterior light fails.
UNDERSTANDING YOUR INSTRUMENT PANEL 103 14. Seat Belt Indicator Light With the key in the ignition, the light comes on, and a warning sounds for a short time if the driver’s seat belt is not fastened. After starting the engine, the seat belt indicator light blinks and a chime sounds periodically for up to 90 seconds to remind the driver and passenger to fasten the seat belts. Fastening the seat belts will extinguish the light and silence the chime.
UNDERSTANDING YOUR INSTRUMENT PANEL 17. Electronic Digital Clock A digital readout in the instrument cluster shows the time in hours and minutes whenever the ignition switch is in the ON/RUN or ACC position. 20. Trip Odometer, Flexible Service System (FSS) Indicator This display shows the distance traveled since last reset. When the ignition switch is in the OFF/LOCK position, timekeeping is accurately maintained.
UNDERSTANDING YOUR INSTRUMENT PANEL 105 22. Push Button for Activating the Instrument Cluster, Intensity of Instrument Lights, for Resetting Trip Odometer and Flexible Service System (FSS) Indicator Press the knob/button to illuminate the display. To vary the intensity of the instrument cluster lights, rotate the knob/button. To reset the trip odometer, press the knob/button once with the key in the ON/RUN position. Press the knob/ button twice with the key removed or in the OFF/LOCK or ACC position.
UNDERSTANDING YOUR INSTRUMENT PANEL After approximately 10 seconds, a signal sounds and the display shows 7,000 miles (Canada: 11,000 km) for approximately 10 seconds. 5. Release the knob/button. If the FSS counter was inadvertently reset, have an authorized dealer correct it. The message is displayed for approximately 10 seconds when turning the key to the ON/RUN position, or while driving when reaching the service warning threshold. It can be canceled manually by pressing the knob/button.
UNDERSTANDING YOUR INSTRUMENT PANEL 107 The sensor for the outside temperature indicator is located in the front fascia area. Due to its location, the sensor can be affected by road or engine heat during idling or slow driving. This means that the accuracy of the displayed temperature can only be verified by comparison to a thermometer placed next to the sensor, not by comparison to external displays (e.g., bank signs, etc.).
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! WARNING! In the event a malfunction of the airbag is indicated, the airbag may not be operational. For your safety, we strongly recommend that you visit an authorized dealer immediately to have the system checked; otherwise the airbag may not be activated when needed in an accident, which could result in serious or fatal injury, or it might deploy unexpectedly and unnecessarily which could also result in injury.
UNDERSTANDING YOUR INSTRUMENT PANEL 109 If the Check Engine light remains on continuously and the vehicle is driving normally, you may still drive the vehicle. In most situations, the vehicle will not require towing. However, we recommend that you have the system checked at an authorized dealer as soon as possible.
UNDERSTANDING YOUR INSTRUMENT PANEL • OK • -1.0 Q (-1.0L) • -1.5 Q (-1.5L) • -2.0 Q (-2.0L) • HI The indicated amount of oil must be added to the engine if the message -2.0 Q (-2.0L) blinks and a signal sounds. The HI message indicates that the excess oil must be removed from the pan to avoid possible engine or catalytic converter damage.
UNDERSTANDING YOUR INSTRUMENT PANEL 111 “INFINITY MODULUS” AM/FM STEREO RADIO WITH SINGLE-DISC CD PLAYER INFINITY MODULUS Entertainment Systems A premium Infinity Modulus AM/FM stereo, single-disc CD audio system is standard equipment in your Crossfire. It feeds a six-channel, 240-watt amplifier with dual subwoofers mounted in the back panel behind the seats, and four door-mounted speakers. Power/Volume Control To activate the audio system, press the ON/OFF knob on the left.
UNDERSTANDING YOUR INSTRUMENT PANEL • Treble (TREB) Press the AUD button repeatedly until TREB appears. Rotate the right rotary control for the desired level (from -9 to +9). • Balance (BAL) Press the AUD button repeatedly until BAL appears. Rotate the right rotary control for the desired level (from -9 to +9). • Linear adjustment (LINEAR) The tone values for the set signal source (e.g., radio/ FM) are set to “0” (mean value).
UNDERSTANDING YOUR INSTRUMENT PANEL 113 BEST FM – The BEST FM function automatically memorizes and continuously updates the frequencies of stations in order of their signal strength. The strongest station comes up first when BEST FM is selected. Stations with stronger or weaker signals are selected by turning the right rotary knob. To select the displayed station, press the right rotary control/push button.
UNDERSTANDING YOUR INSTRUMENT PANEL The following are examples of program types displayed: • REL MUSC – Religious Music • NEWS – News Service • TOP 40 – Top 40 • SOFT – Soft Music • REL TALK – Religious Talk • INFORM – Information Programs • COUNTRY – Country Music • NOSTALGA – Nostalgia • PERSNLTY – Personality • SPORTS – Sports Reports • OLDIES – Oldies Format • JAZZ – Jazz Music • PUBLIC – Public Radio • TALK – Talk Programs • WEATHER – Weather Forecast • CLASSICL – Classical • PTY
UNDERSTANDING YOUR INSTRUMENT PANEL 115 Once the scan search begins, it will continue until either a station is retained or until another mode is selected. Tuning AM stations – Rotating the right rotary control to the right or left will change the AM frequency to the next higher or lower station with a strong signal. To manually step through each frequency or tune in a station with a weaker signal, press the MAN button first, and then rotate the rotary control right or left.
UNDERSTANDING YOUR INSTRUMENT PANEL Insert the CD into the slot with the printed side up. The unit will display the number of tracks and total playback time. After the last track has been played back, the unit automatically begins to play the first track again. To eject a disc, briefly press and release the EJT button. If the power is turned off, the disc will remain in the CD slot for protection. Features of the CD player: • Skipping Tracks Turn the right rotary control/push button.
UNDERSTANDING YOUR INSTRUMENT PANEL 117 NOTE: To protect the unit from excessive heat, a temperature protection device has been integrated into the circuitry. When a high operating temperature is detected, CD TEMP is displayed for eight seconds and the unit switches back to the last source (AM or FM). Allow sufficient cool down time and retry.
UNDERSTANDING YOUR INSTRUMENT PANEL • STO AUTO – Setting for normal operation. The unit switches from stereo to mono and back, depending on the reception conditions (for nearly all reception areas, this is the optimal setting). • STEREO – Setting for exceptional conditions. The unit is constantly set for stereo reception (primarily for private broadcasters in urban areas). • MONO – Setting for receptions with constant reflection, the unit is constantly set for monaural reception.
UNDERSTANDING YOUR INSTRUMENT PANEL 119 COMPACT DISC MAINTENANCE To keep the compact discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store the disc in its case after playing. 6.
UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS 5. Air Conditioning ON/OFF 6. Rear Window Defroster 7. Air Distribution (Mode) Control The climate control system allows you to balance the temperature, amount and direction of the air circulating throughout the vehicle. The system is always at operational readiness, except when manually switched off. The climate control only operates with the engine running. 1. Driver Temperature Control 2. Passenger Temperature Control 3. Fan Speed Control 4.
UNDERSTANDING YOUR INSTRUMENT PANEL 121 The settings and controls are as follows: Temperature Control Use the driver or passenger temperature control to regulate the temperature of the air inside the passenger compartment. The blue area of the control indicates cooler temperatures, while the red area indicates warmer temperatures. The temperature selector should be left at the desired temperature setting so that the system can automatically reach that selection as quickly as possible.
UNDERSTANDING YOUR INSTRUMENT PANEL Basic Setting - Air Conditioner Press the air conditioning ON/OFF switch. The light in the switch will illuminate. Select a temperature for each side of the passenger compartment. Select the air volume with the fan control switch, at least to position 1. Set the air distribution control switch to one of the positions shown above. Open center air outlets. Open left and right side air outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 123 Defogging Windows Fogged Up On Inside Press the A/C button; the indicator light should illuminate. Switch off the air recirculation; the indicator light should go out. Set the air distribution control switch to the defrost position. Increase air volume with the fan control switch. Close the center, left, and right side air outlets. Turn the defroster outlets for the side windows to the detent position. Windshield Fogged Up On Outside Switch on the windshield wipers.
UNDERSTANDING YOUR INSTRUMENT PANEL Climate Control - OFF To switch the climate control off, set the air volume control switch to position 0. The fresh air supply to the vehicle interior is shut off. While driving, use this setting only temporarily, otherwise the windshield could fog up. Rear Window Defroster Turn the key in the ignition switch to the ON/RUN position. To select, press the rear window defroster button once and release. The indicator light in the switch should illuminate.
UNDERSTANDING YOUR INSTRUMENT PANEL 125 Air Recirculation/REST This mode can be selected to temporarily reduce the entry of annoying odors or dust into the vehicle’s interior. Outside air does not flow into the vehicle’s interior. To select, press the recirculation button. To cancel, press the recirculation button again. Residual Engine Heat Utilization (REST) With the engine switched off, it is possible to continue heating the interior for a short while. Air volume is controlled automatically.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: This vehicle is equipped with an air conditioner system that uses R-134a (HFC: hydrofluorocarbon) as a refrigerant. Repairs should always be performed by a qualified technician, and refrigerant should be collected in a recovery system for recycling. Dust Filter Nearly all dust particles and pollen are filtered out before outside air enters the passenger compartment through the air distribution system.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 129 ▫ Neutral . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 129 ▫ Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 ▫ Extremely Cold Weather (Below -20°F Or -29°C) . . . . . . . . . . . . . . . . . 129 ▫ AutoStick威 Gear Selection . . . . . . . . . . . . . . . 134 ▫ If Engine Fails To Start . . . . . . . . . . . . .
STARTING AND OPERATING ▫ ESP Control Switch . . . . . . . . . . . . . . . . . . . . 143 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . . 155 ▫ Anti-Lock Brake System (ABS) . . . . . . . . . . . . 144 ▫ Tire Rotation Recommendations . . . . . . . . . . . 156 ▫ Brake Pad Break-In . . . . . . . . . . . . . . . . . . . . 147 ▫ Alignment And Balance . . . . . . . . . . . . . . . . . 157 䡵 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 147 䡵 Fuel Requirements . . . . . . .
STARTING AND OPERATING 129 STARTING PROCEDURES WARNING! NOTE: Due to the starter non-repeat feature, the key must be turned completely to the left before attempting to start the engine again. Do not leave animals or children inside parked vehicles in hot weather; interior heat build up may cause serious injury or death. Be sure that the parking brake is engaged and that selector lever is in the NEUTRAL or PARK position. Turn the key in the ignition switch to the ON/RUN position.
STARTING AND OPERATING If Engine Fails to Start CAUTION! Do not try to push or tow your vehicle to get it started. Your vehicle cannot be started this way. Pushing with another vehicle may damage the transmission or the rear of your vehicle. See Section 6 of this manual for proper jump-starting procedures. WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire, causing serious personal injury.
STARTING AND OPERATING 131 After Starting The idle speed will automatically decrease as the engine warms up. Automatic Transmission TRANSMISSION SHIFTING WARNING! When leaving the vehicle, always remove the key from the ignition switch, and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Children could move the gearshift lever, which could result in an accident or serious injury.
STARTING AND OPERATING The gear shifting process is continuously adapted, dependent on the driving style, the driving situation and the road characteristics. The selector lever is automatically locked while in the PARK position. To move the selector lever out of the PARK position, the brake pedal must be firmly depressed before the shift lock will release. Shift the selector lever to the desired position only when the engine is idling normally and the brake pedal is applied.
STARTING AND OPERATING 133 Maneuvering To maneuver in tight areas, control the vehicle speed by gradually releasing the brakes. Accelerate gently and never abruptly step on the accelerator. NOTE: The key can be removed from the ignition switch only with the selector lever in the PARK position. With the key removed, the selector lever is locked in the PARK position. To rock a vehicle out of soft ground (mud or snow), alternately shift from forward to reverse, while applying only slight acceleration.
STARTING AND OPERATING the tool from the opening, the cover will not close fully. Only after moving the selector lever to the “D+” and “D-” positions does the cover return to its closed position. Neutral No power is transmitted from the engine to the drive axle. When the brakes are released, the vehicle can be moved freely (pushed or towed). Do not engage in NEUTRAL position while driving except to coast when the vehicle is in danger of skidding (e.g., on icy roads).
STARTING AND OPERATING 135 into another gear that allows for quicker acceleration or to slow the vehicle down is possible. Downshifts can also be performed. Press and hold the selector lever in the “D-” direction. The transmission will shift from the current gear directly to the best gear for acceleration. NOTE: To avoid overrevving the engine when the selector lever is moved in “D-” direction, the transmission will not shift to a lower gear if the engine’s revolutions per minute limit would be exceeded.
STARTING AND OPERATING Gear Ranges “P” PARK “D” OVERDRIVE NOTE: If the key is in the ON/RUN position, you must press the brake pedal to shift out of the PARK position. This range should be used for most city and highway driving. It provides the smoothest upshifts and downshifts and best fuel economy. PARK supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to use PARK while the vehicle is in motion.
STARTING AND OPERATING 137 For standard mode, press the “S” symbol on the switch. Use this mode for all regular driving. The vehicle starts out in FIRST gear. Depressing the accelerator pedal rapidly or nearly to the floor while driving (kickdown position), rather than depressing the accelerator pedal in slow, small movements, will cause the automatic transmission to shift down into a lower gear. Rapid release of the accelerator pedal will normally result in an upshift.
STARTING AND OPERATING 4. Wait approximately 10 seconds. 5. Restart the engine. Before leaving the vehicle, make sure that the parking brake is fully applied and place the gear selector in the PARK position. 6. Move the selector lever to the DRIVE position (for SECOND gear), or move the selector lever to the REVERSE position (for REVERSE gear). Have the transmission checked at your authorized dealer as soon as possible.
STARTING AND OPERATING 139 When parking on a hill, you must set the parking brake before placing the gear selector in PARK. If you don’t, the load on the transmission locking mechanism may make it difficult to move the selector out of PARK. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. BRAKE SYSTEM Your vehicle is equipped with power brakes as standard equipment.
STARTING AND OPERATING BAS assistance. To receive the benefit of the system you must apply continuous, full braking power during the stopping sequence. Do not reduce brake pedal pressure. The malfunction indicator light for the BAS is combined with the Electronic Stability Program (ESP) malfunction indicator light.
STARTING AND OPERATING 141 system. As a result, it is possible that only partial engine output will be available, and pressing the accelerator pedal will require more effort. If the BAS malfunctions, the brake system functions in the usual manner, but without BAS. With the ABS malfunctioning, the BAS and ESP will be disabled. In this condition, both malfunction indicator lights come on while the engine is running.
STARTING AND OPERATING WARNING! CAUTION! ESP cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded. The ESP cannot prevent accidents, including those resulting from excessive speed in turns, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents. The capabilities of an ESP equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others.
STARTING AND OPERATING 143 Synchronizing ESP If the power supply was interrupted (battery disconnected or discharged), the BAS/ESP malfunction indicator light may be illuminated with the engine running. To re-synchronize the ESP, and cancel the malfunction indicator light, the steering angle sensor will need to be recalibrated. ESP Control switch The ESP control switch is located in the center console. When the ESP is switched off, the warning light in the instrument cluster comes on.
STARTING AND OPERATING illuminated. With the ESP system switched off, the engine torque reduction feature is cancelled. Therefore, the enhanced vehicle stability offered by ESP is unavailable. CAUTION! Snow chains should never be used without the recommended mud and snow (M+S) rated radial-ply tires. Damage to your vehicle may result from such usage. ESP always operates under braking, even with the switch in the OFF position.
STARTING AND OPERATING 145 In the case of an emergency brake maneuver, keep continuous full pressure on the brake pedal. In this manner only can the ABS be most effective. On slippery road surfaces, the ABS will respond even with light brake pedal pressure because of the increased likelihood of locking wheels. The pulsating brake pedal can be an indication of hazardous road conditions and functions as a reminder to take extra care while driving.
STARTING AND OPERATING briefly during this procedure, or remains on after the engine is running, have the system checked by an authorized dealer. below 10 volts, the malfunction indicator light comes on and the ABS is switched off. When the voltage is above this value again, the malfunction indicator light should go out and the ABS is operational. If the malfunction indicator light stays illuminated, have the system checked at your authorized dealer as soon as possible.
STARTING AND OPERATING 147 WARNING! To use your brakes and accelerator more safely, follow these tips: • Do not “ride” the brakes by resting your foot on the pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping distances, or brake damage. • When descending mountains or hills, repeated braking can cause brake fade with loss of braking control. Avoid repeated heavy braking by downshifting the transmission whenever possible.
STARTING AND OPERATING TIRES Please take the time to read the tire warranty booklet in your Owner’s Manual package. It contains valuable information on tire maintenance. Specific recommendations on guidelines for long-term tire storage should be requested of the tire manufacturer. Please refer to the tire warranty booklet for contact information. Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 149 2. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3. Ride Comfort And Vehicle Stability Proper tire inflation contributes to a comfortable ride. Overinflation produces a jarring and uncomfortable ride.
STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap—if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.” Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after a 3 hour period.
STARTING AND OPERATING 151 WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident.
STARTING AND OPERATING transmit tire pressure readings to a computer which monitors for low pressure. If low pressure is measured, the TPM Indicator Light will illuminate. The TPM system informs you of a low tire pressure condition. If this occurs, correct your tire inflation pressure as soon as possible, and inspect all of your tires. Be sure to use a high quality gauge when adjusting pressure.
STARTING AND OPERATING 153 if the temperature is very cold. ALWAYS check the pressure in your tires if the TPM lamp is illuminated. CAUTION! Tire Chains The RUD-matic威 DISC is the only tire chain system approved for use on the Chrysler Crossfire. Damage to the vehicle may result if unapproved tire chains are used. Chains should only be used on the rear wheels and only with the recommended winter mud and snow (M+S) tires and wheels. Follow the manufacturer’s mounting instructions.
STARTING AND OPERATING Snow Tires Some areas of the country require the use of snow tires during winter. See the recommended snow type winter tire applications in this section. WARNING! Your vehicle may be equipped with sport performance tires that are optimized for driving in dry and wet weather conditions. However, these tires have reduced traction capability in snow and ice.
STARTING AND OPERATING 155 Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm). When the indicators appear in two or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at this point.
STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING 157 Alignment And Balance The suspension components of your vehicle should be inspected and aligned when needed to obtain full tire tread mileage. Poor suspension alignment may result in: • Fast tire wear • Uneven tire wear, such as feathering and one-sided wear • Vehicle pull to right or left Tires may also cause vehicle to pull to the left or right. Alignment will not correct this condition. See your authorized dealer for proper diagnosis.
STARTING AND OPERATING FUEL REQUIREMENTS Your engine is designed to meet all emissions regulations and provide satisfactory fuel economy and optimum performance when using high quality unleaded gasoline having an octane rating of 91 or higher. DaimlerChrysler Corporation requires the use of 91 octane or higher premium fuel to minimize the potential for engine damage. Light spark knock at low engine speeds is not harmful to your engine.
STARTING AND OPERATING 159 CAUTION! DO NOT use gasolines containing Methanol. Use of these blends may result in starting and drivability problems and may damage critical fuel system components. Problems that result from using methanol/gasoline blends are not the responsibility of DaimlerChrysler Corporation and may not be covered by the Limited Warranty. While MTBE is an oxygenate made from Methanol, it does not have the negative effects of Methanol.
STARTING AND OPERATING states adopting California emission standards, your vehicle will operate satisfactorily on fuels meeting Federal specifications, but emission control system performance may be adversely affected. ADDING FUEL Gasoline sold outside of California is permitted to have higher sulfur levels, which may affect the performance of the vehicle’s catalytic converter. This may cause the CHECK ENGINE light to illuminate.
STARTING AND OPERATING 161 NOTE: The fuel tank filler tube has a restricting door about 2 inches (50 mm) down from the opening. If fuel is poured from a portable container, the container should have a flexible nozzle long enough to force open the restricting door. CAUTION! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. With the key in the ignition switch turned to the ON/ RUN position, the fuel reserve warning light comes on.
STARTING AND OPERATING VEHICLE LOADING The load carrying capacity of your vehicle is in the following chart and on the tire pressure label attached to the driver door pillar. Vehicle Loading Capacities Front Seat Occupants . . . . . . . . . . . . . . . . . . . . . . . 2 Cargo Capacity (with two persons) . . . . 115 lbs. (52 kg) Rated Vehicle Capacity. . . . . . . . . . . . 415 lbs.
STARTING AND OPERATING 163 WARNING! TRAILER TOWING Trailer towing with your Crossfire is not recommended. Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof luggage rack “Cautions” when carrying cargo on your roof rack.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 166 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 166 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 177 䡵 TIREFIT Tire Repair And Jacking . . . . . . . . . . 167 䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . 178 ▫ TIREFIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 ▫ Towing Eyes . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is located in the console. Push in the flasher switch and all front and rear directional signals will flash. Press the flasher switch a second time to turn the flashers off. NOTE: With extended use, the flasher may run down your battery. IF YOUR ENGINE OVERHEATS During severe operating conditions and stop-and-go city traffic, the coolant temperature may rise close to the red area on the gauge.
WHAT TO DO IN EMERGENCIES 167 NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the cooling system and turning off the A/C removes this heat. You can also turn the temperature control to maximum heat, the mode control to floor, and the fan control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the cooling system.
WHAT TO DO IN EMERGENCIES WARNING! 1. TIREFIT sealant bottle 2. Air pump flap 3. Recess in air pump 4. Power plug and cable 5. Air pump hose with pressure gauge 6. Hose connection on sealant bottle Cuts or punctures larger than approximately 0.16 in. (4 mm), tire damage caused by driving with extremely low tire pressure or on a flat tire, or a damaged wheel can pose a hazard while driving. TIREFIT should not be used in such circumstances. Do not drive the vehicle under such circumstances.
WHAT TO DO IN EMERGENCIES 169 Sealing tire with TIREFIT 1. Set the parking brake and turn on the hazard warning flashers. 10. Insert the power plug (4) into the power point on the instrument panel. 11. Turn the ignition key to the ON/RUN position. 2. Move the transmission selector lever to the PARK position and turn off the engine. 12. Press the switch on the air pump to 1. The air pump should start to inflate the tire. 3.
WHAT TO DO IN EMERGENCIES 16. If a tire pressure of 26 psi (180 kPa) is obtained, press the air pump switch to 0, turn the ignition switch to the OFF/LOCK position, and disconnect the TIREFIT system. 17. Drive the vehicle for about 10 minutes to ensure optimum distribution of the tire sealant within the tire. 18. Check the pressure in the tire. If the pressure is above 19 psi (130 kPa), inflate the tire to the pressure indicated on the tire pressure label on the driver side latch pillar. 19.
WHAT TO DO IN EMERGENCIES 171 WARNING! Do not attempt to repair a tire on the side of the vehicle close to traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or repairing a tire. Jacking the vehicle should only be necessary in the event that a tire has been severely damaged, and must be replaced. (See TIREFIT Tire Repair section for a description of cuts and punctures that may be repairable with TIREFIT.
WHAT TO DO IN EMERGENCIES • Passengers must not remain in the vehicle when the vehicle is jacked. NOTE: The jack is designed exclusively for jacking up the vehicle at the specified jack location points built beneath either side of the vehicle. Jack Location and Instructions 1. Remove the jack and jack handle from stowage beneath the cargo compartment carpet. 2.
WHAT TO DO IN EMERGENCIES 173 6 NOTE: Do not raise the vehicle until you are sure the jack is securely engaged, as shown. 3. Holding the jack, insert the cradle under the lifting points. Crank the handle clockwise until the jack base meets the ground. Place the jack on firm ground. Position the jack so that it is always level, even if the vehicle is parked on an incline. Raise the vehicle only until the tire just clears the surface. Minimum tire lift provides maximum stability. 4. Replace the tire. 5.
WHAT TO DO IN EMERGENCIES NOTE: Before storing the jack, it should be fully collapsed. 6. Ensure proper tire pressure. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to make the necessary repair. WARNING! A loose jack or tool thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and tools in the places provided.
WHAT TO DO IN EMERGENCIES 175 WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush contaminated area immediately with large quantities of water. A battery generates hydrogen gas that is flammable and explosive. Keep flame or spark away from the vent holes.
WHAT TO DO IN EMERGENCIES 3. Turn off the heater, radio and all unnecessary electrical loads. 6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fans. NOTE: If engine does not run after several unsuccessful starting attempts, have it checked at the nearest authorized dealer.
WHAT TO DO IN EMERGENCIES 177 Traction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observed: 1. Slow down during rainstorms or when roads are slushy. 2. Slow down if the road has standing water or puddles. 3.
WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE We recommend that the vehicle be transported using flat bed equipment. This method is preferable to other types of towing. CAUTION! Important! If towing the vehicle, please note the following: With the automatic central locking activated and the key in the ignition switch turned to the ON/RUN position, the vehicle doors lock if the left front wheel and the right rear wheel are turning at vehicle speeds of approximately 9 mph (15 km/h) or more.
WHAT TO DO IN EMERGENCIES 179 CAUTION! • Do not attempt to tow this vehicle from the front with sling-type towing equipment. Damage to the front fascia will result. • Always use wheel lift equipment when towing from the front. The only other approved method of towing is with a flatbed truck. • Do not tow the vehicle from the rear. Damage to the rear sheet metal and fascia will occur. • Do not push or tow this vehicle with another vehicle as damage to the bumper fascia and transmission may result.
WHAT TO DO IN EMERGENCIES Insert the tool (or similar sized screwdriver) into the slot in the grille as shown (the tool must be inserted far enough to engage the clip on the left side of the grille). Push the tool to the left to disengage the clip and detach the grille. The front towing eye is now accessible.
WHAT TO DO IN EMERGENCIES 181 6 Tow-Away Alarm Once the alarm system has been armed, the exterior vehicle lights will flash and an alarm will sound when anyone attempts to raise the vehicle for towing. The alarm will last approximately three minutes in the form of flashing exterior lights. At the same time, an alarm will sound for 30 seconds. The alarm will stay on even if the vehicle is immediately lowered.
WHAT TO DO IN EMERGENCIES the vehicle is locked again with a key or the remote control, at which time it is automatically reactivated. CONVERTIBLE TOP EMERGENCY OPERATION If the convertible top cannot be closed using the convertible top switch, check the following: • Is the decklid closed properly? • Is there sufficient battery voltage? Start the engine if necessary.
WHAT TO DO IN EMERGENCIES 183 Relieving Hydraulic Pressure 1. Lower the windows and open the doors. NOTE: The hydraulic pressure must be relieved before the top can manually be raised or lowered. 2. Turn the ignition key off. 1. Turn the ignition to the “ON” position. 2. Push down on the convertible top switch and hold in that position. 3. Turn the ignition “OFF” and continue to push down on the switch for 5 seconds. 4. After 5 seconds the hydraulic system pressure will be relieved.
WHAT TO DO IN EMERGENCIES 3. Unlock the storage compartment by placing the tool on the bolt between the backrest and the tonneau cover. Turn the wrench in the direction of the arrow to its stop and remove the tool. 5. Pull up hard on the upper section of the convertible top to move it out of its storage compartment. NOTE: Do not let go of the convertible top as it may fall back into the convertible top storage compartment. 4. Open the tonneau cover and secure it in the upright position.
WHAT TO DO IN EMERGENCIES 185 6. Move the convertible top toward the windshield header. 8. Place the rear window section of the convertible top in its vertical position. 9. Close the tonneau cover by placing hands near the edges (arrows) and slowly lowering it. The tonneau cover must lock in the first notch of the compartment cover catch. 6 WARNING! Do not place your hands in the convertible top frame areas. Serious personal injury may occur. 7.
WHAT TO DO IN EMERGENCIES 10. Lock the convertible top storage compartment by placing the tool on the bolt between the backrest and the tonneau cover. Turn the wrench in the direction of the arrow to its stop and remove the tool. 11. Lower the rear window section of the convertible top down and lock into the tonneau cover. 12. Press latch handle release button and fold down the locking latch handle.
WHAT TO DO IN EMERGENCIES 187 13. Turn the latch handle just past one quarter turn clockwise and pull the convertible top frame carefully down until it meets the windshield header attachment points. 6 15. Fold the latch handle up until the release button engages. 14. Turn the latch handle counterclockwise to the stop in order to lock the convertible top. The convertible top is now locked onto the windshield header.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 3.2L SRT Engine . . . . . . . . . . . . . . . . . . . . . . . 191 ▫ Power Steering Fluid . . . . . . . . . . . . . . . . . . . 203 䡵 Onboard Diagnostic System (OBD II) . . . . . . . 192 ▫ Chassis Lubrication . . . . . . . . . . . . . . . . . . . . 204 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 ▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . . 204 䡵 Replacement Parts . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 ▫ Front Turn Signal And Parking/Standing Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 䡵 Convertible Top Care . . . . . . . . . . . . . . . . . . . 219 ▫ Front And Rear Sidemarker Lights . . . . . . . . . 229 ▫ Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 ▫ Tail, Stop, Back Up And Turn Signal Lights . . .
MAINTAINING YOUR VEHICLE 191 3.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) To meet new government regulations and promote cleaner air, your Crossfire is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions and engine control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 193 EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the CHECK ENGINE Light is functioning and is not on when the engine is running, and that the OBD (Onboard Diagnostic) system is ready for testing.
MAINTAINING YOUR VEHICLE b. The CHECK ENGINE light will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station. If your OBD system is not ready, you should see your authorized dealer or repair facility.
MAINTAINING YOUR VEHICLE 195 WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent technician. MAINTENANCE PROCEDURES The pages that follow contain the maintenance service recommended by the engineers who designed your vehicle.
MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off, or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between the MIN and MAX markings on the dipstick. Adding one quart of oil when the reading is at the MIN mark will result in a MAX reading on this engine.
MAINTAINING YOUR VEHICLE 197 Change Engine Oil The oil change interval for your Crossfire is initially set at 7,000 miles (Canada: 11,000 km). The Flexible Service System (FSS) in your vehicle evaluates engine temperature, oil level, vehicle speed, engine speed, distance driven, and the time elapsed since your last service. It determines when your vehicle needs maintenance service and alerts you in advance. The next necessary service is indicated by the FSS in your instrument cluster.
MAINTAINING YOUR VEHICLE Engine Oil Selection For best performance and maximum protection under all types of operating conditions, only use synthetic engine oils, approved to MB 229.3 or MB 229.5, such as Mobil 1 SAE 0W-40. The FSS may not alert for an oil change at the proper interval if an unapproved engine oil is used; engine damage and reduced engine life may result. Materials Added To Engine Oils Do not add materials (other than leak detection dyes) to engine oil.
MAINTAINING YOUR VEHICLE 199 Drive Belts - Check Condition and Tension At the distance shown in the maintenance schedules, check all drive belts for condition and proper tension. Improper belt tension can cause belt slippage and failure. Engine Air Cleaner Filter Under normal driving conditions, replace the air filter at each interval called out by FSS. Inspect the drive belts for evidence of cuts, cracks, or glazing and replace them if there is any sign of damage which could result in belt failure.
MAINTAINING YOUR VEHICLE Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly serviced to assure proper catalyst operation and prevent possible catalyst damage. If the CHECK ENGINE light is flashing, immediate service is required.
MAINTAINING YOUR VEHICLE 201 In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating. If this occurs, stop the vehicle, turn off the engine and allow it to cool. Service, including a tune up to DaimlerChrysler Corporation’s specifications, should be obtained immediately.
MAINTAINING YOUR VEHICLE WARNING! CAUTION! Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling. Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water. Battery gas is flammable and explosive.
MAINTAINING YOUR VEHICLE 203 NOTE: If your air conditioning performance seems lower than expected, check the front of the A/C condenser for an accumulation of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser as required. Fabric front fascia protectors may reduce air flow to the condenser, reducing air conditioning performance. Power Steering Fluid No power steering fluid service is required. The system is filled at the factory with Pentosin CHF 11S.
MAINTAINING YOUR VEHICLE Drive Shaft Universal Joints Your vehicle has four constant velocity universal joints. Periodic lubrication of these joints is not required. However, the joint boots should be inspected for external leakage or damage when other maintenance is performed. If leakage or damage is evident, replace the universal joint boot and grease immediately. Chassis Lubrication Front Suspension Ball Joints There are two front suspension lower ball joints that are permanently lubricated.
MAINTAINING YOUR VEHICLE 205 It is important to maintain proper lubrication to insure that the hood mechanisms work properly and safely. Multi-Purpose Lubricant, NLGI Grade 2, should be applied sparingly to all pivot and sliding contact areas. Driver’s Door Lock Cylinder The driver’s door lock cylinder should be lubricated twice a year, preferably in the fall and spring.
MAINTAINING YOUR VEHICLE 4. Install the new blade assembly onto the wiper arm tip until it locks in place. Windshield Washer Reservoir The washer fluid reservoir is located in the engine compartment and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent (not radiator antifreeze) rated not to freeze at -25°F (-31°C). Operate the system for a few seconds to flush out the residual water. WARNING! Do not overfill the washer reservoir.
MAINTAINING YOUR VEHICLE 207 WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition key is in the ON position. • You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool.
MAINTAINING YOUR VEHICLE 209 If the solution is dirty and contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Engine Coolant Disposal Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community.
MAINTAINING YOUR VEHICLE Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing, according to the temperatures occurring in the area where the vehicle is operated. Cooling System Pressure Cap The cap must be fully tightened to prevent loss of coolant, and to insure that coolant will return to the radiator from the coolant reserve tank. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.
MAINTAINING YOUR VEHICLE 211 • If frequent coolant additions are required, or if the level in the recovery bottle does not drop when the engine cools, the cooling system should be pressure tested for leaks. • Maintain a coolant concentration of a minimum of 50% ethylene glycol Extended Life Coolant and high quality water with recommended antifreeze for proper corrosion protection of your engine cooling system that contains aluminum components.
MAINTAINING YOUR VEHICLE WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency. Brake and Power Steering System Hoses When servicing the vehicle for scheduled maintenance, inspect surface of hoses and nylon tubing for evidence of heat and mechanical damage.
MAINTAINING YOUR VEHICLE 213 Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning light is on. Be sure to clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reservoir. Fluid level can be expected to fall as the brake pads wear. Brake fluid level should be checked when pads are replaced.
MAINTAINING YOUR VEHICLE CAUTION! CAUTION! Do not allow petroleum-based fluid to contaminate the brake fluid as seal damage will result! Using a transmission fluid other than the fluid recommended by DaimlerChrysler Corporation may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the DaimlerChrysler Corporation will result in more frequent fluid and filter changes.
MAINTAINING YOUR VEHICLE 215 NOTE: Refer to Section 8 of this manual for Maintenance Schedules. • Road salt, dirt and moisture accumulation Appearance Care and Protection from Corrosion • Insects, tree sap and tar Protection of Body and Paint from Corrosion Vehicle body protection requirements vary according to geographic locations and usage.
MAINTAINING YOUR VEHICLE CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels and rear liftgate / decklid be kept clear and open.
MAINTAINING YOUR VEHICLE 217 When cleaning extremely dirty wheels, care must be taken in the selection of tire and wheel cleaning chemicals and equipment to prevent damage to the wheels. Only Mopar威 Wheel Cleaners are recommended. Any of the “DO NOT USE” items listed below can damage wheels and wheel trim. DO NOT USE: • Any abrasive cleaner • Any abrasive cleaning pad (such as steel wool) or abrasive brush • Any cleaner that contains an acid which can react with and discolor the chrome surface.
MAINTAINING YOUR VEHICLE ammonia based cleaners to clean your leather upholstery. Application of a leather conditioner is not required to maintain the original condition. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing. CAUTION! Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses.
MAINTAINING YOUR VEHICLE 219 Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in the vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. • Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. • Dry with a soft tissue.
MAINTAINING YOUR VEHICLE Washing General Cleaning CAUTION! • Remove bird droppings immediately. The organic acid can damage the material and cause the top to leak. • Never use a power washer to clean the top, as you may damage the top material. • If an automatic car wash is used, never use hotwax. Hand washing is highly recommended. Automatic car washing equipment can damage the top material. If you must use an automatic car wash, soft cloth systems are preferred.
MAINTAINING YOUR VEHICLE 221 Wet Cleaning Wash with clear water or with a mild detergent and an ample supply of luke warm water by wiping with a soft-bristled brush or sponge from front to rear. Then rinse thoroughly with clear water. Allow the top to dry before lowering. Vacuuming the top with a wet/dry shop vacuum will decrease the top’s drying time, ensure removal of all dirt, and delete streaks in the material. Multiple cleanings may be necessary to remove stubborn stains.
MAINTAINING YOUR VEHICLE CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it shows a problem in the circuit that must be corrected.
MAINTAINING YOUR VEHICLE 223 Underhood Accessory Fuse Block Fuses Cavity 1 2 3 4 5 5 6 6 7 Fuse 5 Amp Beige 5 Amp Beige 5 Amp Beige 7.
MAINTAINING YOUR VEHICLE Cavity 8 9 10 11 12 13 14 15 16 17 Fuse 15 Amp Blue 10 Amp Red 5 Amp Beige 15 Amp Blue 10 Amp Red 10 Amp Red 10 Amp Red 5 Amp Beige 40 Amp Orange Circuits Radio Cavity 18 Roof Light, Horn, Anti-Theft Alarm, Cargo Lamp and Tire Pressure Control Speed Control 19 20 21 Ignition Coil 6 Cyl.
MAINTAINING YOUR VEHICLE 225 Cavity 31 32 33 34 34 35 36 36 37 Fuse 15 Amp Blue 15 Amp Blue 5 Amp Beige 30 Amp Green 15 Amp Blue 30 Amp Green 5 Amp Beige 5 Amp Beige Circuits Cigar Lighter, Glove Compartment Light Wiper, Washer Pump, Headlight Flasher Climate Control Relay Control Module Fuses Spare (Coupe) Climate Control (Roadster) Radio Frequency Remote Control, Hazard Warning Flasher, Instrument Cluster, Climate Control Climate Control (Coupe) Exterior Mirror Adjustment (Roadster) Circulating Air,
MAINTAINING YOUR VEHICLE Interior Fuses Relay Control Module Cavity Fuse 1 15 Amp Blue 2 15 Amp Blue 3 15 Amp Blue 4 40 Amp Orange 5 15 Amp Blue 6 15 Amp Blue Fuses Circuits Traction System Engine Control 2 Engine Control 1 Air Pump Fuel Pump Horn The fuse access door is located on the end of the instrument panel on the driver’s side behind the trim panel cover. Use a coin or flat blade screwdriver to open and close this access door.
MAINTAINING YOUR VEHICLE 227 Cavity 5 6 7 8 9 10 11 Interior Cavity 1 2 3 4 Fuses Fuse Circuits Not Assigned 15 Amp Blue Brake Lamp/Speed Control 7.5 Amp Right High Beam, High Beam Brown Indicator Light 15 Amp Blue Reverse/Turn signal Light 12 13 14 Fuse 7.5 Amp Brown 15 Amp Blue 7.5 Amp Brown 15 Amp Blue 15 Amp Blue 7.5 Amp Brown 7.
MAINTAINING YOUR VEHICLE REPLACEMENT BULBS EXTERIOR LIGHT BULB SERVICE Interior Light Bulbs For lighted switches and interior lights, see your authorized dealer for servicing requirements. Headlights Exterior Light Bulbs Bulb Bulb No. Headlight - High and Low Beam . . . . . . 12V55W H7U Front Turn Signal . . . . . . . . . . . . . . . . . . . . . . . Y21W Front Parking/Standing Light . . . . . . . . . . . . . . W5W Front Side Marker Light . . . . . . . . . . . . . . . . . . W5W Rear Marker Light . .
MAINTAINING YOUR VEHICLE 229 3. Release the spring clamps holding the bulb in place, and pull out the bulb. Replace the bulb and reverse the removal procedure exactly. Front Turn Signal and Parking/Standing Lights • Twist the bulb socket counterclockwise and pull out. Push the bulb into the socket, turn counterclockwise and remove. • Replace the bulb, push in and twist clockwise. Reinstall the socket, and turn clockwise. Front and Rear Sidemarker Lights 1.
MAINTAINING YOUR VEHICLE 4. Realign the two tabs and push the light in until it engages into the lock. License Plate Light Tail, Stop, Back Up and Turn Signal Lights 1. Open the rear liftgate / decklid and remove the access door in the trim panel. 2. Twist the bulb socket counterclockwise and pull out. 3. Replace the light and return to open socket, turn clockwise until it stops. 4. Replace the access door in the trim panel. 1. Remove the two lens assembly mounting screws. 2.
MAINTAINING YOUR VEHICLE 231 NOTE: Always test the operation of all lights after service operations have been performed to validate an effective repair. the vehicle and then readjust the headlights to the original position. If any further adjustments are necessary contact your manufacturer’s dealer. A detailed service procedure is contained in the manufacturer’s Service Manual. Information on purchasing a Service Manual can be found at the back of this Owner’s Manual.
MAINTAINING YOUR VEHICLE • If the vehicle will be subjected to freezing temperatures, remove the battery and store it in a dry, wellventilated place. If the vehicle is not going to be driven in the next three weeks, follow the battery recharge procedure in the Service Manual, then disconnect the battery at the negative terminal. CAUTION! Use care when disconnecting the remote positive cable. It is connected to the battery and can short out to any metal on the vehicle.
MAINTAINING YOUR VEHICLE 233 NOTE: To help prevent the battery from discharging during shorter periods of inactivity, perform the following: 1. Make sure that the rear liftgate/decklid, hood, and doors are completely closed. 2. Make sure that the remote transmitter is operating and that the battery is good. 3. Make sure that the hood, rear liftgate and door switches are in adjustment. 4. Use the remote transmitter to set the alarm. SPECIFICATIONS Engine Specifications Engine Size Mode of Operation No.
MAINTAINING YOUR VEHICLE Performance Specifications (approximate) Maximum Speed Acceleration 0–60 mph (0-96 km/h) 0-100 mph-0 (0-161 km/ h-0) 158 mph (255 km/h) 5.3 seconds < 16 seconds Gear Ratios - 5-Speed Automatic Transmission First Second Third Fourth Fifth Reverse 3.595 2.186 1.405 1.00 0.831 3.16/1.93 Body Specifications Overall Length Maximum Width Maximum Width With Mirrors 159.8 in. (4058 mm) 69.5 in. (1766 mm) 76.9 in.
MAINTAINING YOUR VEHICLE 235 FLUID CAPACITIES Fuel (Approximate) Fuel Tank Reserve Engine Oil (with filter) 3.2 L Supercharged Engine Cooling System * 3.2 L Supercharged Engine Automatic Transmission Rear Axle Power Steering Reservoir Brake Reservoir Windshield Washer Reservoir * Includes heater and coolant recovery bottle filled to MAX level. Metric 60.0 Liters 8.0 Liters U.S. 15.8 Gallons 2.1 Gallons 8.0 Liters 8.5 Qts. 14.5 Liters 8.0 Liters 1.3 Liters 1.0 Liters .5 Liters 7.0 Liters 15.3 Qts. 8.
MAINTAINING YOUR VEHICLE RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs Spark Plug Gap Fuel Selection Fluids, Lubricants and Genuine Parts Use coolant approved to MB 325.0, such as Valvoline GO5, or an equivalent extended life coolant. Only use synthetic engine oils, approved to MB 229.3 or MB 229.5, such as Mobil 1 SAE 0W-40.
MAINTAINING YOUR VEHICLE 237 Chassis Component Automatic Transmission Brake Master Cylinder Power Steering Reservoir Rear Axle Fluid Tire Pressure Fluids, Lubricants and Genuine Parts Only use ATF approved to MB 236.10, MB 236.12. Synthetic Dexron III威 Transmission Fluid may be substituted. Use brake fluid approved to MB 331.
MAINTAINING YOUR VEHICLE Body Component Fluids, Lubricants and Genuine Parts Hinges: Door Mopar威 Spray White Lube Liftgate / Decklid Mopar威 Multi-Purpose Lube NLGI Grade 2 EP, GC-LB Hood Springs and Links Mopar威 Spray White Lube Latches: Liftgate/Decklid Mopar威 Spray White Lube Hood/Safety Catch Mopar威 Multi-Purpose Lube NLGI Grade 2 EP, GC-LB Door Mopar威 Spray White Lube Seat Regulator and Track Mopar威 Multi-Purpose Lube NLGI Grade 2 EP, GC-LB Window System Components Mopar威 Spray White Lube Loc
MAINTENANCE SCHEDULES CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 240 䡵 Regular Check-Ups . . . . . . . . . . . . . . . . . . . . . 246 M A I N T E N A N C E S 䡵 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240 ▫ Additional Periodic Maintenance . . . . . . . . . . 247 C 䡵 Emission Control System Maintenance . . . . . . 241 䡵 Special Maintenance Requirements . . . . . . . . . 248 E 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E S C H E D U L E S 8 240 MAINTENANCE SCHEDULES INTRODUCTION This is intended as a guide to the service requirements of your vehicle. It contains all necessary instructions concerning service intervals and operations which have to be carried out. Scope and frequency of maintenance work primarily depend on the vehicle’s operating conditions. In the interest of maintaining the vehicle’s operating safety, the specified work should be performed regularly and in good time.
MAINTENANCE SCHEDULES 241 M A The use of Special lubricant additives is not recommended. The use of such additives may affect your warranty rights. With regard to legal stipulations concerning emissions control, please note that engines have to be serviced and adjusted in accordance with special instructions and using special measuring equipment. Modifications to or interference with the emissions control systems are not permissible.
M A I N T E N A N C E 242 MAINTENANCE SCHEDULES Your Flexible Service System (FSS) — see Understanding Your Instrument Panel section — should give you an exact indication of when your vehicle should be scheduled for service and which schedule to follow. Additional Periodic Maintenance items should also be performed beyond the items listed in the following charts to assure the optimum performance of your Crossfire.
MAINTENANCE SCHEDULES 243 M SCOPE OF WORK FOR “B” SCHEDULE MAINTENANCE SERVICE Oil Change • Change oil and replace filter Maintenance • Rotate tires • Replace dust filter • Lubricate hood hinges, latch, and secondary latch • Reset FSS Display Function Check • Horn, hazard warning flashers, turn signals, and indicator lamps A I N front and rear brake pads for lining thickness T E N condition of front and rear brake discs A N tires for damage and general condition C tire inflation pressures and correct if n
M A I N T E N A N C E 244 MAINTENANCE SCHEDULES • Engine cooling system (check corrosion inhibitor/ antifreeze) The oil change interval for your Crossfire is initially set at 7,000 miles (Canada: 11,000 km). Very light duty driving cycles (most trips more than 10 miles [16 km] at moderate speeds in moderate temperature conditions) can extend the service interval beyond 7,000 miles (Canada: 11,000 km).
MAINTENANCE SCHEDULES 245 M A There are two symbols which will appear in the main odometer display field prior to the next suggested service. This symbol represents Service A. This second symbol represents Service B. Service B rotates with Service A and includes additional service tasks. The next service is normally calculated and displayed next to the Service A or Service B symbol as distance remaining before the next service is required.
M A I N T E N A N C E S C H E D U L E S 8 246 MAINTENANCE SCHEDULES REGULAR CHECK-UPS To maintain the safe operation of your vehicle, it is recommended that you perform the following tasks on a regular basis (i.e., weekly or whenever the vehicle is refueled). • Check the windshield washer solvent and add if required. • Inspect wiper blade condition. • Check operation of lighting systems. CAUTION! • Inspect tires for unusual wear, damage, and pressure (at least every 14 days).
MAINTENANCE SCHEDULES 247 M Additional Periodic Maintenance The following maintenance items should be performed during the scheduled maintenance nearest the time elapsed and/or distance shown. Follow the interval that occurs first. Every 2 years: • Inspect body for paint damage. • Check chassis and supporting body parts for damage and corrosion. At approximately every 50,000 miles (80,000 km) or 4 years: • Check condition of driveshaft flex discs.
M A I N T E N A N C E S C H E D U L E S 8 248 MAINTENANCE SCHEDULES SPECIAL MAINTENANCE REQUIREMENTS Coolant Have the corrosion inhibitor/antifreeze concentration in the coolant checked before the onset of winter (once a year in countries with high prevailing temperatures). Have the coolant replaced every five years or 100,000 miles (161,000 km). Dust Filter for Heating/Ventilation Replacement The dust filter is replaced during routine maintenance service.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250 ▫ Prepare For The Appointment . . . . . . . . . . . . 250 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 250 ▫ Be Reasonable With Requests . . . . . . . . . . . . . 250 䡵 If You Need Assistance . . . . . . . . . . . . . . . . . . 250 䡵 Warranty Information . . . . . . . . . . . . . . . . . . . 252 䡵 Mopar威 Parts . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty; discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a valuable clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE 251 • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the DaimlerChrysler Corporation’s Customer Center.
IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unexpected repairs after your DaimlerChrysler Corporation’s new vehicle limited warranty expires. The DaimlerChrysler Corporation stands behind only the DaimlerChrysler Corporation’s Service Contracts.
IF YOU NEED CONSUMER ASSISTANCE 253 9
IF YOU NEED CONSUMER ASSISTANCE MOPAR姞 PARTS Mopar威 fluids, lubricants, parts, and accessories are available from your authorized dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 states of the United States and Washington, D.C.
IF YOU NEED CONSUMER ASSISTANCE 255 PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mastercard, American Express, and Discover orders are accepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals. (No P.O. Boxes). • Service Manuals.
IF YOU NEED CONSUMER ASSISTANCE TIRE SAFETY INFORMATION Tire Markings NOTE: European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H. NOTE: LT(Light Truck)-Metric tire sizing is based on U.S. design standards.
IF YOU NEED CONSUMER ASSISTANCE 257 EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ...blank...ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
IF YOU NEED CONSUMER ASSISTANCE Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. i.e. tire pressure, vehicle loading, road conditions and posted speed limits.
IF YOU NEED CONSUMER ASSISTANCE 259 Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
IF YOU NEED CONSUMER ASSISTANCE Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: Some vehicles have a “Tire and Loading Information” placard located on the driver’s side “B” pillar. This placard tells you important information about the, 1. number of people that can be carried in the vehicle 2. the total weight your vehicle can carry 3. the tire size designed for your vehicle 4. the cold tire inflation pressures for the front, rear and spare tires.
IF YOU NEED CONSUMER ASSISTANCE 261 Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
IF YOU NEED CONSUMER ASSISTANCE 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
IF YOU NEED CONSUMER ASSISTANCE 263 9
IF YOU NEED CONSUMER ASSISTANCE WARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle-never overload them.
INDEX 10
INDEX ABS (Anti-Lock Brake) System . . . . . . . . . . . . . 102 Adding Engine Coolant (Antifreeze) . . . . . . . . . 209 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 160 Aiming Headlights . . . . . . . . . . . . . . . . . . . . . . 231 Air Cleaner, Engine (Engine Air Cleaner Filter) . 199 Air Conditioning . . . . . . . . . . . . . . . . . . . . 120,202 Air Conditioning Filter . . . . . . . . . . . . . . . . . . . 248 Air Conditioning Refrigerant . . . . . . . . . . . . . .
INDEX 267 Cargo Compartment Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 Catalytic Converter . . . . . . . . . . . . . . . . . . . . . 200 CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . 111,115 Chains, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . 167 Charging System Light . . . . . . . . . . . . . . . . . . . 103 Checks, Safety . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Disposal Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 198 Door Locks, Automatic . . . . . . . . . . . . . . . . . . . 13 Drive Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199 Drive Shaft Universal Joints . . . . . . . . . . . . . . . 204 Driving On Slippery Surfaces . . . . . . . . . . . . . . . . 151,176 Electronic Speed Control . . . . . . . . . . . . . . . . . . 86 Electronic Stability Program . . . . . . . . . . . . . . . .
INDEX 269 Garage Door Opener . . . . . . . . . . . . . . . . . . . . . 89 Gas Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235 Gasoline/Oxygenate Blends . . . . . . . . . . . . . . . 158 Gear Ratios . . . . . . . . . . . . . . . . . . . . . . . . . . . 233 Glass Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . 218 Glove Compartment . . . . . . . . . . . . . . . . . . . . . 65 Inside Rearview Mirror . . . .
INDEX Daytime Running . . . . . . . . . . . . . . . . . . . . . . 74 Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Exterior Check . . . . . . . . . . . . . . . . . . . . . . . . 48 Fog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Hazard Warning Flasher . . . . . . . . . . . . . . . . 166 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . 73 Interior . . . . . . . . . . . . . . . .
INDEX 271 Disposal . . . . . . . . . . . . . Filter . . . . . . . . . . . . . . . Materials Added to . . . . . Recommendation . . . . . . Oil Filter, Selection . . . . . . . Onboard Diagnostic System Overheating, Engine . . . . . . Owner’s Manual . . . . . . . . . . . . . . . . . . . . . . . 198 . . . . . . . . . . . . . . . 198 . . . . . . . . . . . . . . . 198 . . . . . . . . . . . . . . . 198 . . . . . . . . . . . . . . . 198 . . . . . . . . . . . . 192,193 . . . . . . . . . . . . . . . 166 . . . . . .
INDEX Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 And Pregnant Women . . . . . . . . . . . . . . . . . . 28 Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 219 Operating Instructions . . . . . . . . . . . . . . . . . . 25 Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 Seats . . . . . . . . . . . . . . . .
INDEX 273 Pressure Label . . . . . . . . . . . . . . . . . . . . . . . 149 Pressure Monitor System . . . . . . . . . . . . . 80,151 Quality Grading . . . . . . . . . . . . . . . . . . . . . . 256 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 155 Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 Snow Tires . . . . . . . . . . . . .
NOTES
NOTES
NOTES
NOTES
NOTES
NOTES
NOTES
