2014 Cherokee 2014 OWNER’S MANUAL Chrysler Group LLC 14KL74-126-AA First Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated nondrinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 WARNINGS AND CAUTIONS . . . . . . . . . . . . . .7 䡵 ROLLOVER WARNING . . . . . . . . . . . . . . . . . . .4 䡵 VEHICLE IDENTIFICATION NUMBER . . . . . . . .7 䡵 HOW TO USE THIS MANUAL . . . . . . . . . . . . . .5 䡵 VEHICLE MODIFICATIONS/ALTERATIONS . . . .
4 INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained techniLLC vehicle. Be assured that it represents precision cians and genuine parts, and cares about your satisfaction. workmanship, distinctive styling, and high quality - all ROLLOVER WARNING essentials that are traditional to our vehicles.
INTRODUCTION 5 two million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. HOW TO USE THIS MANUAL Consult the Table of Contents to determine which section contains the information you desire. Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustrations may differ from your vehicle’s equipment.
6 INTRODUCTION
INTRODUCTION 7 WARNINGS AND CAUTIONS This Owners Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owners Manual, you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel.
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A WORD ABOUT YOUR KEYS . . . . . . . . . . . . .12 䡵 VEHICLE SECURITY ALARM — IF EQUIPPED . . . . . . . . . . . . . . . . . . ▫ Ignition Node Module (IGNM) — If Equipped. .12 ▫ Rearming Of The System . . . . . . . ▫ Keyless Ignition Node (KIN) . . . . . . . . . . . . . .13 ▫ To Arm The System . . . . . . . . . . . ▫ Key Fob — If Equipped . . . . . . . . . . . . . . . . . .14 ▫ To Disarm The System . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .25 䡵 WINDOWS . . . . . . . . . . . . . . . . . . . . . . . . . . .44 ▫ Programming Additional Transmitters. . . . . . . .25 ▫ Power Windows . . . . . . . . . . . . . . . . . . . . . . .44 ▫ Transmitter Battery Replacement . . . . . . . . . . .25 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . .47 ▫ General Information . . . . . . . . . . . . . . . . . . . .29 䡵 LIFTGATE . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Enhanced Seat Belt Use Reminder System 䡵 ENGINE BREAK-IN RECOMMENDATIONS (BeltAlert®) . . . . . . . . . . . . . . . . . . . . . . . . . .64 䡵 SAFETY TIPS . . . . . . . . . . . . . . . . . . . . . . ▫ Seat Belts And Pregnant Women . . . . . . . . . . .65 ▫ Transporting Passengers . . . . . . . . . . . . . . ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . .65 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE are OFF, ACC, and ON/RUN. The START position is a spring-loaded momentary contact position. When released Your vehicle uses either a key start ignition system or from the START position, the switch automatically returns keyless ignition system. The key start ignition system to the ON/RUN position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Keyless Ignition Node (KIN) This feature allows the driver to operate the ignition switch with the push of a button, as long as the Remote Keyless Entry (RKE) transmitter is in the passenger compartment. The Keyless Ignition Node (KIN) has four operating positions, three of which are labeled and will illuminate when in position. The three positions are OFF, ACC, and ON/RUN. The fourth position is START, during start RUN will illuminate.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key Fob — If Equipped The Key Fob also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the Key Fob go dead. You can keep the emergency key with you when valet parking.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 2 Ignition Node Module (IGNM) Emergency Key Removal Keyless Ignition Node (KIN) Emergency Key Removal NOTE: You can insert the double-sided emergency key into the lock cylinders with either side up.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Ignition Or Accessory On Message Opening the driver’s door when the ignition is in ACC or ON (engine not running), a chime will sound to remind you to cycle the ignition to OFF. In addition to the chime, the ignition or accessory on message will display in the cluster.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 WARNING! (Continued) • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. CAUTION! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended. SENTRY KEY® The Sentry Key® Immobilizer system prevents unauthorized vehicle operation by disabling the engine. The system does not need to be armed or activated.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! CAUTION! The Sentry Key® Immobilizer system is not compatible with some after-market remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. • Always remove the Key Fobs from the vehicle and lock all doors when leaving the vehicle unattended. • For vehicles equipped with Keyless Enter-N-Go™, always remember to place the ignition in the OFF position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: When having the Sentry Key® Immobilizer Sys- VEHICLE SECURITY ALARM — IF EQUIPPED tem serviced, bring all vehicle keys with you to an The Vehicle Security Alarm monitors the vehicle doors authorized dealer. for unauthorized entry and the Keyless Enter-N-Go™ Start/Stop button for unauthorized operation.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Arm The System Follow these steps to arm the Vehicle Security Alarm: same exterior zone (refer to ⬙Keyless Enter-N-Go™⬙ in ⬙Things To Know Before Starting Your Vehicle⬙ for further information). 1. Remove the key from the ignition system (refer to • Press the LOCK button on the Remote Keyless Entry ⬙Starting Procedures⬙ in ⬙Starting And Operating⬙ for (RKE) transmitter. further information). 3. If any doors are open, close them.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 • Cycle the vehicle ignition system out of the OFF position. • For vehicles equipped with Keyless Enter-N-Go™ , press the Keyless Enter-N-Go™ Start/Stop button (requires at least one valid Key Fob in the vehicle). • For vehicles not equipped with Keyless Enter-NGo™ , insert a valid key into the ignition switch and turn the key to the ON position. NOTE: • When the Vehicle Security Alarm is armed, the interior power door lock switches will not unlock the doors.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Security System Manual Override NOTE: The Vehicle Security Alarm will not arm if you lock the • The front courtesy overhead console and door courdoors using the manual door lock plunger. tesy lights do not turn on if the dimmer control is in the ⬙Dome ON⬙ position (extreme top position).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 To Unlock The Doors And Liftgate Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door or twice within five seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on. If the vehicle is equipped with Passive Entry, refer to “Keyless Enter-N-Go™” under “Things To Know Before Starting Your Vehicle” for further information.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Flash Lights With Remote Key To Lock The Doors And Liftgate This feature will cause the turn signal lights to flash when the doors are locked or unlocked with the RKE transmitter. This feature can be turned on or turned off. To change the current setting, refer to “Uconnect® Settings” in “Understanding Your Instrument Panel” for further information. Press and release the LOCK button on the RKE transmitter to lock all doors and liftgate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 • You may need to be less than 35 ft (11 m) from the vehicle when using the RKE transmitter to turn off the To turn the Panic Alarm feature on or off, press and hold Panic Alarm due to the radio frequency noises emitted the PANIC button on the RKE transmitter for at least one by the system. second and release.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Remove the emergency key by sliding the mechanical latch on the back of the RKE transmitter sideways with your thumb and then pull the key out with your other hand. Keyless Ignition Node (KIN) Emergency Key Removal Ignition Node Module (IGNM) Emergency Key Removal 2. separating RKE halves requires screw removal and gently prying the two halves of the RKE transmitter apart. Make sure not to damage the seal during removal.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 2 Remove Screw From Transmitter Case Separating Ignition Node Module (IGNM) Transmitter Case
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar, then replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery clip, located on the back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 General Information REMOTE STARTING SYSTEM — IF EQUIPPED This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conveniently from outside the vehicle while still maintaining security. The system has a range of approximately 300 ft (91 m). • This device may not cause harmful interference.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Hood closed • Liftgate/Flipper Glass closed • Hazard switch off • Brake switch inactive (brake pedal not pressed) • Ignition key removed from ignition switch • Battery at an acceptable charge level • RKE PANIC button not pressed • System not disabled from previous remote start event • Vehicle theft alarm not active WARNING! • Do not start or run an engine in a closed garage or confined area.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 • Remote Start Aborted — Fuel Low NOTE: • Remote Start Aborted — Liftgate Ajar • If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds. • Remote Start Disabled — Start Vehicle To Reset • The park lamps will turn on and remain on during The EVIC message stays active until the ignition is turned Remote Start mode. to the ON/RUN position.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Exit Remote Start Mode Without Driving The Vehicle Press and release the REMOTE START button one time or allow the engine to run for the entire 15 minute cycle. NOTE: • For vehicles not equipped with the Keyless Enter-NGo™ feature, the ignition switch must be in the ON/RUN position in order to drive the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Remote Start Comfort Systems — If Equipped DOOR LOCKS When remote start is activated, the heated steering wheel, and driver heated seat features will automatically turn on in cold weather. In warm weather, the driver vented seat feature will automatically turn on when the remote start is activated. These features will stay on through the duration of remote start or until the ignition switch is turned to the ON/RUN position.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • For personal security and safety in the event of a collision, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • When leaving the vehicle, always remove the Key Fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 If you press the power door lock switch while the ignition is in the ACC or ON/RUN position, and any front door is open, the power locks will not operate. This prevents you from accidentally locking the Key Fob in the vehicle. Cycling the ignition to the OFF position or closing the door will allow the locks to operate. If a door is open, and the ignition is in the ACC or ON/RUN position, a chime will sound as a reminder to remove the Key Fob.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Unlock Doors On Exit Child-Protection Door Lock System — Rear The doors will unlock automatically on vehicles with Doors To provide a safer environment for small children riding power door locks if: in the rear seats, the rear doors are equipped with a 1. The Automatic Unlock Doors On Exit feature is enChild-Protection Door Lock system. abled. To use the system, open each rear door, use a flat blade 2. All doors are closed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 NOTE: • When the child lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position. • After disengaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the desired position. • After engaging the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the desired position.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the Child-Protection locks are engaged. KEYLESS ENTER-N-GO™ The Passive Entry system is an enhancement to the vehicle’s Remote Keyless Entry (RKE) system and a feature of Keyless Enter-N-Go™. This feature allows you to lock and unlock the vehicle’s door(s) without having to press the RKE transmitter lock or unlock buttons.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 To Unlock From The Passenger Side With a valid Passive Entry RKE transmitter within 5 ft (1.5 m) of the passenger door handle, grab the front passenger door handle to unlock all four doors automatically. The interior door panel lock knob will raise when the door is unlocked.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE FOBIK-Safe only executes in vehicles with passive entry. NOTE: The vehicle will only unlock the doors when a There are three situations that trigger a FOBIK-Safe valid Passive Entry RKE transmitter is detected inside the search in any passive entry vehicle. vehicle, and no valid Passive Entry RKE transmitter is detected outside the vehicle. The vehicle will not unlock 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 To Unlock/Enter The Liftgate The liftgate passive entry unlock feature is built into the electronic liftgate handle. With a valid Passive Entry RKE transmitter within 3 ft (1.0 m) of the liftgate, press the electronic liftgate handle for a power open on vehicles equipped with Power Liftgate. Press the electronic liftgate handle and lift for Manual Liftgate vehicles.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If “Unlock All Doors 1st Press” is programmed in EVIC, all doors will unlock when you push the button on the liftgate. If ⬙Unlock Driver Door 1st press⬙ is programmed in Uconnect®, only the liftgate will unlock when you press the button on the liftgate. For further information, refer to “Uconnect®” in “Understanding Your Instrument Panel”. To Lock The Vehicle’s Doors And Liftgate With one of the vehicle’s Passive Entry RKE transmitters within 5 ft (1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 NOTE: • After pressing the door handle LOCK button, you must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking. • The Passive Entry system will not operate if the RKE transmitter battery is dead.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There are single window controls on each passenger door trim panel, which operate the passenger door windows. Power Windows The window controls will operate only when the ignition The window controls on the driver’s door control all the is in the ACC or ON/RUN position. door windows. NOTE: For vehicles equipped with the Uconnect®, the power window switches will remain active for up to 10 minutes after the ignition is cycled to the OFF position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 WARNING! (Continued) in the ACC or ON/RUN mode. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. AUTO-Down Feature AUTO-Up Feature With Anti-Pinch Protection Lift the window switch to the second detent, release, and the window will go up automatically.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Window Lockout Switch The window lockout switch on the driver’s door trim panel allows you to disable the window controls on the rear passenger doors. To disable the window controls, press and release the window lockout button (setting it in the DOWN position). To enable the window controls, Reset Auto-Up press and release the window lockout button again Should the Auto Up feature stop working, the window (setting it in the UP position).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof or Sky Slider™ open, adjust the sunroof or Sky Slider™ opening to minimize the buffeting or open any window.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The liftgate passive entry lock button will only NOTE: Use the power door LOCK switch on either front lock the liftgate, the liftgate unlock feature is built into door trim panel or the Remote Keyless Entry (RKE) the electronic liftgate handle. transmitter to lock and unlock the liftgate. The manual door locks on the doors and the driver’s door lock cylinder will not lock and unlock the liftgate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 on the Remote Keyless Entry (RKE) transmitter. Press the NOTE: LIFTGATE button on the RKE transmitter twice within • In the event of a power malfunction to the liftgate, an five seconds, to open the power liftgate. Once the liftgate emergency liftgate latch release can be used to open is open, pressing the button twice within five seconds a the liftgate. The emergency liftgate latch release can be second time will close the liftgate.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The power liftgate must be in the full open position for rear liftgate close button on the left rear trim, near the The power liftgate buttons will not operate if the liftgate opening to operate. If the liftgate is not fully vehicle is in gear or the vehicle speed is above 0 mph open, press the Liftgate button on the Key Fob to fully (0 km/h). open the liftgate, and then press it again to close.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 • If your liftgate is power closing and you put the OCCUPANT RESTRAINTS vehicle in gear, the liftgate will continue to power Some of the most important safety features in your close. However, vehicle movement may result in a vehicle are the restraint systems: detection of an obstruction. • Three-point lap and shoulder belts for all seating positions WARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Front seat belts incorporate pretensioners that may NOTE: The Advanced Front Air Bags have a multistage enhance occupant protection by managing occupant inflator design. This allows the air bag to have different rates of inflation based on several factors, including the energy during an impact event severity and type of collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Children that are not big enough to wear the vehicle seat belt 4. Do not lean against the door or window. If your properly (see section on Child Restraints) should be secured vehicle has side air bags, and deployment occurs, the in the rear seat in child restraints or belt-positioning booster side air bags will inflate forcefully into the space seats. Older children who do not use child restraints or between you and the door.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air Bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • Supplemental Side Air Bag Inflatable Curtain (SABIC) and Seat-Mounted Side Air Bags (SAB) also need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Lap/Shoulder Belts WARNING! (Continued) All seating positions in your vehicle are equipped with lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. However, in a collision, the belt will lock and reduce your risk of striking the inside of the vehicle or being thrown out.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the front seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap. Pulling Out The Lap/Shoulder Belt Latch Plate 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 WARNING! Inserting Latch Plate Into Buckle • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up a bit on the shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt may not protect you properly. In a collision, it could even cut into you. Be sure the belt is straight.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front seating positions, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Press the release button to release the anchorage, and then move it up or down to the position that fits you best. NOTE: The adjustable upper shoulder belt anchorage is equipped with an Easy Up feature.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Lap/Shoulder Belt Untwisting Procedure Seat Belts In Passenger Seating Positions Use the following procedure to untwist a twisted lap/ The seat belts in the passenger seating positions are shoulder belt. equipped with Automatic Locking Retractors (ALR) which are used to secure a child restraint system. For additional 1. Position the latch plate as close as possible to the information, refer to “Installing Child Restraints Using The anchor point.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the passenger seating position is equipped with an child safety seat is installed in a seating position that has a belt with this feature. Children 12 years old and under ALR and is being used for normal usage: should always be properly restrained in the rear seat. Only pull the belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not How To Engage The Automatic Locking Mode activate the ALR.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 WARNING! • The belt and retractor assembly must be replaced if the seat belt assembly Automatic Locking Retractor (ALR) feature or any other seat belt function is not working properly when checked according to the procedures in the Service Manual. • Failure to replace the belt and retractor assembly could increase the risk of injury in collisions.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Use Reminder System (BeltAlert®) BeltAlert® is a feature intended to remind the driver and front passenger (if equipped with front passenger BeltAlert®) to fasten their seat belts. The feature is active whenever the ignition is on. If the driver or front seat passenger is unbelted, the Seat Belt Reminder Light will turn on and remain on until both front seat belts are fastened.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Seat Belts And Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the seat belt is not long enough when it is worn low and snug and in the recommended seating positions. Remove and store the extender when not needed.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In addition, the vehicle is equipped with a Supplemental Driver Side Knee Air Bag mounted in the instrument panel below the steering column and a Supplemental Passenger Side Knee Air Bag mounted in the instrument panel below the glove compartment. This vehicle may be equipped with a driver and/or front passenger seat belt buckle switch that detects whether the driver or front passenger seat belt is fastened.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 This vehicle may be equipped with a front passenger • Instrument Panel Occupant Classification System (OCS) that may adjust • Knee Impact Bolster the inflation rate of the Advanced Front Air Bags based • Driver Advanced Front Air Bag upon occupant weight. NOTE: • Passenger Advanced Front Air Bag • Air Bag covers may not be obvious in the interior trim, • but they will open during air bag deployment.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Advanced Front Air Bag Features WARNING! (Continued) The Advanced Front Air Bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as determined by the Occupant Restraint Controller (ORC), which may receive information from the front impact sensors. The first stage inflator is triggered immediately during an impact that requires air bag deployment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 When the air bag deploys, it opens the seam on the side Supplemental Seat-Mounted Side Air Bags (SAB) may of the seat’s trim cover (front seats) and between the side provide enhanced protection to help protect an occupant seat’s cushion trim cover (rear seats). Each air bag deploys independently; a left side impact deploys the left during a side impact.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • Air Bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • Being too close to the SAB and SABIC air bags during deployment could cause you to be severely injured or killed. • Should a vehicle rollover occur, the pretensioners and/or SAB and SABIC air bags on both sides of the vehicle may deploy.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 WARNING! • Your vehicle is equipped with left and right SABIC, do not stack luggage or other cargo up high enough to block the location of the SABIC. The area where the side curtain air bag is located should remain free from any obstructions. • Do not use accessory seat covers or place objects between you and the SAB; the performance could be adversely affected and/or objects could be pushed into you, causing serious injury.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Along with seat belts and pretensioners, Advanced Front Air Bags work with the Supplemental Driver and Passenger Side Knee Air Bags and the passenger side knee bolster to provide improved protection for the driver and front passenger. Side air bags also work with seat belts to improve occupant protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 The Advanced Front Air Bags and Supplemental Driver and Front Passenger Knee Air Bags will not deploy in all frontal collisions, including some that may produce substantial vehicle damage — for example, some pole collisions, truck underrides, and angle offset collisions.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE turns on the Air Bag Warning Light, either momentarily Occupant Classification System (OCS) — Front or continuously. A single chime will sound if the light Passenger Seat comes on again after initial startup. The OCS is part of a Federally regulated safety system for It also includes diagnostics that will illuminate the instru- this vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 The OCS will NOT prevent deployment of the passenger Advanced Front Air Bag.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Never place a rear facing infant seat in front of an air bag. A deploying passenger Advanced Front Air Bag can cause death or serious injury to a child 12 years or younger, including a child in a rearward facing infant seat. • Children 12 years or younger should always ride buckled up in a rear seat in an appropriate child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 WARNING! (Continued) injury or death in a collision. Always wear your seat belt and sit properly, with the seat back in an upright position, your back against the seat back, sitting upright, facing forward, in the center of the seat, with your feet comfortably on or near the floor. Do not carry or hold any objects (e.g., backpacks, boxes, etc.) while seated in the front passenger seat.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The front passenger seatback is not in the full upright position • The front passenger carries or holds an object while seated (e.g., backpack, box, etc.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 2 Not Seated Properly Not Seated Properly
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Placing an object on the floor under the front passenger seat may prevent the OCS from working properly, which may result in serious injury or death in a collision. Do not place any objects on the floor under the front passenger. will turn on whenever the The Air Bag Warning Light OCS is unable to classify the front passenger seat status. A malfunction in the OCS may affect the operation of the air bag system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 The front passenger seat is equipped with Flip ’n Stow™ Only Chrysler Group LLC approved seat accessories may Front Passenger Seat Storage (refer to “Understanding be used. The Features Of Your Vehicle” for additional information). Make sure that objects inside the Flip ’n Stow™ WARNING! Front Passenger Seat Storage bin do not interfere with the latch before closing the seat.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The following requirements must be strictly followed: • Do not modify the front passenger seat assembly or components in any way. • Do not use prior or future model year seat covers or cushions not designated by Chrysler Group LLC for the specific model being repaired. Always use the correct seat cover and cushion specified for the vehicle. • Do not replace the seat cover or cushion with an aftermarket seat cover or cushion.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 When the ORC detects a collision requiring the Advanced Front Air Bags, it signals the inflator units. A large quantity of non-toxic gas is generated to inflate the Advanced Front Air Bags. Different air bag inflation rates are possible, based on several factors, including the collision type and severity.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Seat-Mounted Side Air Bag (SAB) Inflator Units Supplemental Side Air Bag Inflatable Curtain (SABIC) Inflator Units The Supplemental Seat-Mounted Side Air Bags are de- During collisions where the impact is confined to a signed to activate only in certain side collisions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Because air bag sensors estimate deceleration over time, Enhanced Accident Response System perform the followvehicle speed and damage are not good indicators of ing functions: whether or not an air bag should have deployed. • Cut off fuel to the engine. NOTE: In a rollover the pretensioners and/or SAB and • Flash hazard lights as long as the battery has power or SABIC air bags may deploy on both sides of the vehicle. until the ignition is cycled to off.
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If A Deployment Occurs The Advanced Front Air Bags are designed to deflate immediately after deployment. However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 Do not drive your vehicle after the air bags have de- Maintaining Your Air Bag System ployed. If you are involved in another collision, the air bags will not be in place to protect you. WARNING! WARNING! Deployed air bags and seat belt pretensioners can not protect you in another collision. Have the air bags, seat belt pretensioners, and the front seat belt retractor assemblies replaced by an authorized dealer immediately.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion, needs to be serviced in any way (including removal or loosening/tightening of seat attachment bolts), take the vehicle to your authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label located on the inside of the fuse block cover for the proper air bag fuses. See your authorized dealer if the fuse is good.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: EDR data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the EDR under normal driving conditions and no personal data (e.g., name, gender, age, and crash location) are recorded. However, other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. You should also make sure that you can install it in the vehicle where you will use it. NOTE: For additional information, refer to www.seatcheck.org or call 1–866–SEATCHECK. Canadian residents should refer to Transport Canada’s website for additional information: http:// www.tc.gc.ca/eng/roadsafety/safedrivers-childsafetyindex-53.
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Summary Of Recommendations For Restraining Children In Vehicles Infants and Toddlers Small Children Larger Children Children Too Large for Child Restraints Child Size, Height, Weight or Age Children who are two years old or younger and who have not reached the height or weight limits of their child restraint Children who are at least two years old or who have out-grown the height or weight limit of their rear-facing child restraint Children who have out-gr
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 their infant carrier but are still less than at least two years old. Children should remain rearward-facing until they Safety experts recommend that children ride rearwardreach the highest weight or height allowed by their facing in the vehicle until they are two years old or until convertible child seat. they reach either the height or weight limit of their rear facing child safety seat.
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Older Children And Child Restraints Children who are two years old or who have outgrown their rear-facing convertible child seat can ride forwardfacing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who are over two years old or who have outgrown the rear-facing weight or height limit of their rear-facing convertible child seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 Integrated Child Booster Seat — If Equipped 4. Place the child upright in the seat with their back firmly against the seatback. The Integrated Child Booster Seat is located in each outboard second-row passenger seat. The Booster Seat is de- 5. Grasp the latch plate and pull out the seat belt. signed for children weighing between 48 and 85 lbs (22 and 6.
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Securely lock the seat cushion into position before using the seat. Otherwise, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat cushion could cause serious injury.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 Recommendations For Attaching Child Restraints Restraint Type Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Combined Weight of the Child + Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors and Tethers for Children (LATCH) Restraint System Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCHequipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 LATCH Positions For Installing Child Restraints In This Vehicle 2 • • Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the head restraints be removed? Yes The child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint owner’s manual for more information. All three rear seating positions have removable head restraints.
102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating The LATCH Anchorages Center Seat LATCH In addition, there are tether strap anchorages This vehicle has 5 lower LATCH anchorages in the rear behind each rear seating position located on seat. Anchorages A and B are used for the right outboard the back of the seat. position behind the front passenger (1). Anchorages D and E are used for the left outboard position behind the LATCH-compatible child restraint systems will be driver (3).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 103 buckle, the center seat belt can be used to restraint an occupant or child restraint in the center seating position. 2. Right outboard and center seating positions (1 and 2): Install the first child seat in the right outboard seating position using lower anchorages A and B. Install the second child seat using the center anchorages, C and D. Do not use the outer anchorage closest to the opposite door, E.
104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A child restraint installed in the center position (2) will block the seat belt buckle for the empty left outboard seat behind the driver (3). Do not use this seat for another occupant. • Never use the same lower anchorage to attach more than one child restraint. • If you are installing three child restraints next to each other, you must use the seat belt and the center tether anchor for the center position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 105 3. Place the child seat between the lower anchorages for 6. Tighten all of the straps as you push the child restraint that seating position. For some second row seats, you rearward and downward into the seat. Remove slack may need to recline the seat and / or raise the head in the straps according to the child restraint manufacrestraint to get a better fit. turer’s instructions. 4. Attach the lower hooks or connectors of the child 7.
106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the buckled seat belt interferes with the child restraint installation, instead of buckling it behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. Do not lock the seatbelt. Remind all children in the vehicle that the seat belts are not toys and that they should not play with them. WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of the restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 107 refer to the “Automatic Locking Mode” description un- Lap/Shoulder Belt Systems for Installing Child der “Occupant Restraints.” The cinching latch plate is Restraints in this Vehicle designed to hold the lap portion of the seatbelt tight when webbing is pulled tight and straight through a child restraint’s belt path. Please see the table below and the following sections for more information about both types of seat belts.
108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE What is the weight limit (child’s weight + weight of the child restraint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? Can the rear-facing child restraint touch the back of the front passenger seat? Weight limit of the Child Restraint Can the head restraints be removed? Yes Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint? Yes Yes Always use the tether an
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 109 5. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all the seat belt webbing out of the retractor. Then, allow the webbing to retract Place the child seat in the center of the seating back into the retractor. As the webbing retracts, you position. For some second row seats, you may need to will hear a clicking sound.
110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 8. If the child restraint has a top tether strap and the 2. Next, pull enough of the seat belt webbing from the seating position has a top tether anchorage, connect retractor to pass it through the belt path of the child the tether strap to the anchorage and tighten the tether restraint. Do not twist the belt webbing in the belt path. strap. Refer to “Lower Anchors and Tethers for Chil3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 111 6. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. If the belt still cannot be tightened after you shorten the buckle, disconnect the latch plate from the buckle, turn the buckle around one half turn, and insert the latch plate into the buckle again.
112 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts. If not possible, lower the head restraint and pass the tether strap around the outboard side of the head restraint. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 113 WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. If your vehicle is equipped with a split rear seat, make sure the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap.
114 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! WARNING! Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 115 Exhaust Gas WARNING! (Continued) WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO), follow these safety tips: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
116 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seams or loose connections could permit exhaust fumes Air Bag Warning Light to seep into the passenger compartment. In addition, The light should come on and remain on for four inspect the exhaust system each time the vehicle is raised to eight seconds as a bulb check when the for lubrication or oil change. Replace as required. ignition switch is first turned ON.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 117 Floor Mat Safety Information WARNING! (Continued) Always use floor mats designed to fit the footwell of your vehicle. Use only floor mats that leave the pedal area unobstructed and that are firmly secured so that they cannot slip out of position and interfere with the pedals or impair safe operation of your vehicle in other ways. WARNING! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury.
118 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside The Vehicle Door Latches Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Check the wheel nuts for tightness. Check the tires (including spare) for proper cold inflation pressure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . .126 䡵 SEATS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . .126 ▫ Power Seats — If Equipped . . . . . . . . . . . . . .132 ▫ Automatic Dimming Mirror — If Equipped . . .126 ▫ 60/40 Split Folding Rear Seat With Fold-Flat Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . .142 ▫ Outside Mirrors . . . . . . .
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 TO OPEN AND CLOSE THE HOOD . . . . . . . . .149 ▫ Lane Change Assist . . . . . . . . . . . . . . . . . . .156 䡵 LIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151 ▫ High/Low Beam Switch . . . . . . . . . . . . . . . .156 ▫ Headlight Switch . . . . . . . . . . . . . . . . . . . . .151 ▫ Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . .156 ▫ Automatic Headlights — If Equipped . . . . . . .152 ▫ Front Map/Reading Lights . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 䡵 HEATED STEERING WHEEL — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . .166 䡵 ELECTRONIC SPEED CONTROL — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . .169 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . .170 ▫ To Set A Desired Speed . . . . . . . . . . . . . . . . .170 ▫ To Deactivate . . . . . . . . . . . . . . . . . . . . . . . .171 ▫ To Resume Speed . . . . . . . . . . . . . . . . . . . . .
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Normal (Fixed Speed) Cruise Control Mode . . .194 ▫ ParkSense® Warning Display . . . . . . . . . . . . .215 䡵 FORWARD COLLISION WARNING (FCW) WITH MITIGATION — IF EQUIPPED . . . . . . .197 ▫ ParkSense® Display . . . . . . . . . . . . . . . . . . . .215 ▫ Forward Collision Warning (FCW) With Mitigation Operation . . . . . . . . . . . . . . . . . . .197 䡵 LANE DEPARTURE WARNING (LDW) — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 ▫ Service The ParkSense® Park Assist System . . .237 ▫ Cleaning The ParkSense® System . . . . . . . . . .238 ▫ ParkSense® System Usage Precautions. . . . . . .238 䡵 PARKSENSE® ACTIVE PARK ASSIST SYSTEM — IF EQUIPPED . . . . . . . . . . . . . . . .241 ▫ Enabling And Disabling The ParkSense® Active Park Assist System . . . . . . . . . . . . . . .242 ▫ Parallel Parking Space Assistance Operation/Display. . . . . . . . . . . . . . . . . . . . .
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Opening Sunroof — Manual Mode . . . . . . . . .267 䡵 SKY SLIDER™ FULL LENGTH OPEN ROOF — IF EQUIPPED . . . . . . . . . . ▫ Closing Sunroof — Express. . . . . . . . . . . . . . .267 ▫ Sky Slider™ Usage Precautions . . . . ▫ Closing Sunroof — Manual Mode . . . . . . . . . .267 ▫ Sky Slider™ Control . . . . . . . . . . . ▫ Venting Sunroof — Express . . . . . . . . . . . . . .268 ▫ Opening The Sky Slider™ . . . . . . . ▫ Opening Power Shade — Express . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 䡵 CUPHOLDERS . . . . . . . . . . . . . . . . . . . . . . . .282 䡵 REAR WINDOW FEATURES . . . . . . . . . . . . . .288 䡵 STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .282 ▫ Rear Window Wiper/Washer . . . . . . . . . . . . .288 ▫ Glove Box Storage Compartment. . . . . . . . . . .282 ▫ Rear Window Defroster . . . . . . . . . . . . . . . . .290 ▫ Console Storage Compartment . . . . . . . . . . . .283 䡵 ROOF LUGGAGE RACK — IF EQUIPPED . . . .
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the windshield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. This mirror automatically adjusts for headlight glare from vehicles behind you. NOTE: • The Automatic Dimming Mirror feature is disabled when the vehicle is in reverse gear to improve rear view viewing.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Assist Call 9-1-1 Call The rear view mirror contains an ASSIST push button Report an accident without taking your eyes off the road. which automatically connects the vehicle occupants to one Just press 9-1-1 on your mirror and connect. of several predefined locations for immediate support: • Roadside Assistance – If you get a flat tire, or need a tow, just press the Assist button and you’ll be connected to someone who can help.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side convex mirror. 3 Power Mirrors The power mirror switches are located on the driver’s door trim panel.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Models With Express Window Feature Models Without Express Window Feature Press and release the mirror select button marked L (left) or R (right) and then press one of the four arrow buttons to move the mirror in the direction the arrow is pointing. The selection will time out after 30 seconds of inactivity to guard against accidentally moving a mirror position following an adjustment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Illuminated Vanity Mirrors — If Equipped Sun Visor “Slide-On-Rod” Feature — If Equipped An illuminated vanity mirror is on each sun visor. To use The sun visor “Slide-On-Rod” feature allows for additional the mirror, rotate the sun visor down and swing the flexibility in positioning the sun visor to block out the sun. mirror cover upward. The lights will turn on automati1. Fold down the sun visor. cally. Closing the mirror cover will turn off the light. 2.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Power Seats — If Equipped Seats are a part of the Occupant Restraint System of the Some models may be equipped with a power driver’s vehicle. seat. The power seat switch is located on the outboard side of the seat near the floor. Use the switch to move the seat up, down, forward, rearward, or to tilt the seat. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Reclining The Seatback Forward Or Rearward The seatback can be reclined both forward and rearward. Push the seat recliner switch forward or rearward, the seatback will move in the direction of the switch. Release the switch when the desired position has been reached. WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE increase or decrease the lumbar support. Push the switch upward or downward to raise or lower the lumbar support. Front Seat Adjustment Power Lumbar Switch Manual Front Seat Forward/Rearward Adjustment On models equipped with manual seats, the adjusting bar is located at the front of the seats, near the floor. While sitting in the seat, lift up on the bar and move the seat forward or rearward. Release the bar once you have reached the desired position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked. Serious injury or death could result from a poorly adjusted seat belt.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Seat Height Adjustment — If Equipped Heated Seats — If Equipped The driver’s seat height can be raised or lowered by On some models, the front seats may be equipped with using a lever, located on the outboard side of the seat. heaters in both the seat cushions and seatbacks. Pull upward on the lever to raise the seat height or push The front driver and passenger heated seats are operated downward on the lever to lower the seat height.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 WARNING! (Continued) • Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat. 3 Uconnect® 5.0 System — If Equipped Press the “Climate” hard-key located on the right side of the Uconnect® display.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Touch the “Driver” or “Passenger” seat soft-key once to select HI-level heating. Touch the soft-key a second time Touch the “Controls” soft-key located on the bottom of to select LO-level heating. Touch the soft-key a third time the Uconnect® display. to shut the heating elements OFF. Uconnect® 8.4 System — If Equipped Controls Soft-Key Heated Seats Soft-Keys NOTE: Once a heat setting is selected, heat will be felt within two to five minutes.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 When the HI-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the normal HI-level. If the HI-level setting is selected, the system will automatically switch to LO-level after a maximum of 60 minutes of continuous operation. At that time, the display will change from HI to LO, indicating the change.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! The head restraints for all occupants must be properly adjusted prior to operating the vehicle or occupying a seat. Head restraints should never be adjusted while the vehicle is in motion. Driving a vehicle with the head restraints improperly adjusted or removed could cause serious injury or death in the event of a collision. To raise the head restraint, pull upward on the head restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 NOTE: The head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your authorized dealer. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the push button, located at the base of the head restraint, and push downward on the head restraint.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 60/40 Split Folding Rear Seat With Fold-Flat Feature To provide additional storage area, each rear seat can be folded flat. This allows for extended cargo space and still maintains some rear seating room. NOTE: Prior to folding the rear seat, it may be necessary to position the front seat to its mid-track position. Also, be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 To Lower The Rear Seat To Raise The Rear Seat 1. Lift the seatback release lever located on the upper NOTE: If interference from the cargo area prevents the outer edge of the seat or pull the pull strap located on seatback from fully locking, you will have difficulty the middle outer edge of the seat. returning the seat to its proper position. Raise the seatback and lock it into place. WARNING! Be certain that the seatback is securely locked into position.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER MEMORY SEAT — IF EQUIPPED This feature allows the driver to store up to two different memory profiles, for easy recall through a memory switch. Each memory profile contains desired position settings for the driver seat and side mirrors and a set of desired radio station presets. The memory switch is located on the driver’s side door panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 The memory switch allows the driver to recall either of Programming The Memory Feature the two pre-programmed memory profiles by pressing To create a new memory profile, perform the following: the appropriate number button on the switch. NOTE: Saving a new memory profile will erase an existing profile from memory. 1. Turn the ignition ON. 2. Adjust all memory profile settings to desired preferences (i.e., seat, side mirror and radio station presets). 3.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If desired, a second memory profile can be stored into • For vehicles equipped with a manual transmission, the memory as follows: vehicle speed must be at 0 mph (0 km/h) to recall a memory profile. 1. Turn the ignition ON. • The Recall Memory with Remote Key Unlock feature 2. Adjust all memory profile settings to desired prefercan be turned on and off through the EVIC, if ences (i.e., seat, side mirror and radio station presets). equipped.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 To program your RKE transmitters, perform the following: Memory Position Recall 1. Remove the key from the ignition. NOTE: • For vehicles equipped with an automatic transmission, the vehicle must be in PARK to recall memory posi3. Press and release the SET button on the memory tions. If a recall is attempted when the vehicle is not in switch, then within five seconds press and release the PARK, a message will display in the EVIC, if equipped.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To recall the memory settings for driver one, press The distance the driver seat moves depends on where MEMORY button number 1 or the UNLOCK button on you have the driver seat positioned when you remove the the RKE transmitter linked to memory position 1. key from the ignition switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 • The Easy Entry/Easy Exit feature is disabled when the TO OPEN AND CLOSE THE HOOD driver’s seat position is less than 0.9 in (23 mm) Two latches must be released to open the hood. forward of the rear stop. At this position, there is no benefit to the driver by moving the seat for Easy Exit 1. Pull the hood release lever located under the left side of the instrument panel. or Easy Entry.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Move to the outside of the vehicle and pull the safety latch release lever forward (toward you). The safety latch release lever is located behind the center front edge of the hood. CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 LIGHTS Headlight Switch The headlight switch is located on the left side of the instrument panel. This switch controls the operation of the headlights, parking lights, automatic headlights — if equipped, instrument panel lights, instrument panel light dimming, interior lights and fog lights — if equipped. 3 Headlight Switch Rotate the headlight switch clockwise to the first detent for parking light and instrument panel light operation.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch clockwise to the third detent for automatic headlight operation. When the system is on, the headlight time delay feature is also on. This means the headlights will stay on for up to 90 seconds after you place the ignition into the OFF position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 If you turn the headlights off before the ignition, they will detects vehicle specific light and automatically switches from high beams to low beams until the approaching turn off in the normal manner. vehicle is out of view. NOTE: NOTE: • The lights must be turned off within 45 seconds of placing the ignition in the OFF position to activate this • Automatic High Beam Headlamp Control can be turned on or off using the Uconnect® System, refer to feature.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights (DRL) Fog Lights — If Equipped The LED Daytime Running Lights will come on when- The front fog light switch is built into the headlight ever the ignition is placed in the RUN position, the switch. headlights are off, the transmission is moved out of “Park” position, and the parking brake is off. The headlight switch must be used for normal nighttime driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 To activate the front fog lights, turn on the parking lights or the low beam headlights and press the headlight switch. To turn off the front fog lights, either press the headlight switch a second time or turn off the headlight switch. 3 An indicator light in the instrument cluster illuminates when the fog lights are turned on. NOTE: The fog lights will operate with the low beam headlights or parking lights on.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: High/Low Beam Switch • If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. Push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever toward you to switch the headlights back to low beam.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 Interior Lights The interior lights come on when a door is opened. To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition is moved to the LOCK position. This will occur if the interior lights were switched on manually or are on because a door is open. This includes the glove box light, but not the trunk light. To restore interior light operation, either turn the ignition switch ON or cycle the light switch.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE With the parking lights or headlights on, rotating the right dimmer control upward will increase the brightness of the instrument panel lights and lighted cupholders — if equipped. Ambient Light Control Rotate the left dimmer control upward or downward to increase or decrease the brightness of the ambient light located in the overhead console and the door handle lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Dome Light Position Battery Saver Feature Rotate the instrument panel dimmer control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the instrument panel dimmer control is in this position. To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the rear wiper/washer, refer to “Rear Window Features” in Windshield Wiper Operation “Understanding The Features Of Your Vehicle”. Rotate the end of the lever to one of the first four detent positions for intermittent settings, the fifth detent for low wiper operation and the sixth detent for high wiper operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 CAUTION! Always remove any buildup of snow that prevents the windshield wiper blades from returning to the “park” position. If the windshield wiper switch is turned off, and the blades cannot return to the “park” position, damage to the wiper motor may occur. Intermittent Wiper System Use one of the four intermittent wiper settings when weather conditions make a single wiping cycle, with a variable delay between cycles, desirable.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the lever is pulled while the wipers are in the off To use the washer, pull the lever rearward toward you and position, the wipers will operate for several wipe cycles, hold while spray is desired. If the lever is pulled while in the then turn off. intermittent setting, the wipers will turn on and operate for WARNING! several wipe cycles after the lever is released, and then resume the intermittent interval previously selected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 NOTE: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be used in order to spray the windshield with washer fluid. Rain Sensing Wipers — If Equipped This feature senses moisture on the windshield and automatically activates the wipers for the driver. The feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Rain Sensing system has protection features for the wiper blades and arms, and will not operate under the • The Rain Sensing feature will not operate when the following conditions: wiper switch is in the low or high-speed position. • Low Ambient Temperature — When the ignition is • The Rain Sensing feature may not function properly when first turned ON, the Rain Sensing system will not ice, or dried salt water is present on the windshield.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Remote Start Mode Inhibit — On vehicles equipped with Remote Starting system, Rain Sensing wipers are not operational when the vehicle is in the remote start mode. Once the operator is in the vehicle and has placed the ignition switch in the RUN position, rain sensing wiper operation can resume, if it has been selected, and no other inhibit conditions (mentioned previously) exist.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To unlock the steering column, push the control handle downward (toward the floor). To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired. To lock the steering column in position, push the control handle upward until fully engaged. WARNING! Do not adjust the steering column while driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Uconnect® 5.0 System — If Equipped Uconnect® 8.4 System — If Equipped Press the “Climate” hard-key then touch the “Heated Steering Wheel” soft-key to turn on the heated steering wheel. Press the “Heated Steering Wheel” soft-key a second time to turn the heated steering wheel off. Touch the “Controls” soft-key then touch the “Heated Steering Wheel” soft-key to turn on the heated steering wheel.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vehicles Equipped With Remote Start On models that are equipped with remote start, the heated steering wheel can be programmed to come on during a remote start. Refer to “Remote Starting System — If Equipped” in “Things To Know Before Starting Your Vehicle” for further information. WARNING! Heated Steering Wheel Soft-Key NOTE: The engine must be running for the heated steering wheel to operate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 WARNING! (Continued) • Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material. This may cause the steering wheel heater to overheat. 3 ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, the Electronic Speed Control takes over accelerator operations at speeds greater than 25 mph (40 km/h).
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Pressing the SET (+) button once will result in a 1 mph (1 km/h) increase in set speed. Each subsequent tap of A soft tap on the brake pedal, pushing the CANCEL the button results in an increase of 1 mph (1 km/h). button, or normal brake pressure while slowing the vehicle will deactivate Electronic Speed Control without To decrease speed while the Electronic Speed Control is erasing the set speed memory. Pressing the ON/OFF set, push the SET (-) button.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control On Hills The transmission may downshift on hills to maintain the vehicle set speed. WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control and have an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 ACC will allow you to keep cruise control engaged in light to moderate traffic conditions without the constant need to reset your cruise control. ACC utilizes a radar sensor and a forward facing camera designed to detect a vehicle directly ahead of you. NOTE: • If the sensor does not detect a vehicle ahead of you, ACC will maintain a fixed set speed.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Cannot take street, traffic, and weather conditions into account, and may be limited upon adverse sight distance conditions. • Does not always fully recognize complex driving conditions, which can result in wrong or missing distance warnings. • Can only apply a maximum of 40% of the vehicle’s braking capability, and will not bring the vehicle to a complete stop.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 The Cruise Control system has two control modes: • Adaptive Cruise Control mode for maintaining an appropriate distance between vehicles. • Normal (fixed speed) cruise control mode for cruising at a constant preset speed. For additional information, refer to “Normal (Fixed Speed) Cruise Control Mode” in this section. 3 NOTE: Normal (fixed speed) cruise control will not react to preceding vehicles. Always be aware of the mode selected.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Any chassis/suspension or tire size modifica- NOTE: You cannot enable ACC under the following tions to the vehicle will effect the performance of the conditions: Adaptive Cruise Control. • When in Four-Wheel Drive Low. Activating Adaptive Cruise Control (ACC) • When you apply the brakes. You can only engage ACC if the vehicle speed is above • When the parking brake is set. 0 mph (0 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 To turn the system OFF, push and release the Adaptive Push and release the Adaptive Cruise Control (ACC) Cruise Control (ACC) ON/OFF button again. At this ON/OFF button. The ACC menu in the EVIC displays time, the system will turn off and the EVIC will display “Adaptive Cruise Control (ACC) Off.” “ACC Ready.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have a collision. Always leave the system off when you are not using it. To Set A Desired ACC Speed When the vehicle reaches the speed desired, push the SET + button or the SET - button and release. The EVIC will display the set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 • You press the CANCEL switch. To Turn Off • An Anti-Lock Brake System (ABS) event occurs. The system will turn off and clear the set speed in memory if: • A Trailer Sway Control (TSC) event occurs. • The transmission is shifted into NEUTRAL. • You push the Adaptive Cruise Control (ACC) ON/OFF button. • The Electronic Stability Control/Traction Control Sys- • You push the Normal (Fixed Speed) Cruise Control tem (ESC/TCS) activates. ON/OFF button.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: To Vary The Speed Setting • If your vehicle stays at standstill for longer than 2 seconds, then the driver will either have to press the Resume button, or apply the throttle to reengage the ACC to the existing Set Speed. While ACC is set, you can increase the set speed by pressing the SET + button. Pressing the SET + button once will result in a 1 mph (1 km/h) increase in set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 If the SET - button is continually pressed, the set speed • The ACC system maintains set speed when driving up will continue to decrease in 5 mph (5 km/h) increments hill and down hill. However, a slight speed change on moderate hills is normal. In addition, downshifting until the button is released. The decrease in set speed is may occur while climbing uphill or descending downreflected in the EVIC display. hill.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using this distance setting and the vehicle speed, ACC calculates and sets the distance to the vehicle ahead. This distance setting displays in the EVIC.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 3 Distance Setting 2 Bars (Medium) Distance Setting 1 Bar (Short) To increase the distance setting, press the Distance Setting — Increase button and release. Each time the button is pressed, the distance setting increases by one bar (longer).
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To decrease the distance setting, press the Distance • The distance setting is changed. Setting — Decrease button and release. Each time the • The system disengages. (Refer to the information on button is pressed, the distance setting decreases by one ACC Activation). bar (shorter). The maximum braking applied by ACC is limited; howIf there is no vehicle ahead, the vehicle will maintain the ever, the driver can always apply the brakes manually, if set speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 Overtake Aid When driving with ACC engaged and following a target vehicle, the system will provide an additional acceleration to assist in passing vehicles in front. This additional acceleration is triggered when the driver utilizes the left turn signal. In locations with left hand drive traffic, Overtake Aid is active only when passing on the left hand side of the Target vehicles.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ACC Operation at Stop If the ACC system brings your vehicle to a standstill while following a target vehicle, if the target vehicle starts moving within 2 seconds of your vehicle coming to a standstill, your vehicle will resume motion without the need for any driver action. WARNING! When the ACC system is resuming speed, the driver must ensure that there are no pedestrians, vehicles or objects in the path of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Adaptive Cruise Control Ready • ACC Proximity Warning When ACC is activated but the vehicle speed setting has • ACC Unavailable Warning not been selected, the display will read “Adaptive Cruise • The EVIC will return to the last display selected after Control Ready.” five seconds of no ACC display activity.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The “ACC / FCW Unavailable Wipe Front Radar Sensor” message can sometimes be displayed while driving in highly reflective areas (i.e. tunnels with reflective tiles, or ice and snow). The ACC system will recover after the vehicle has left these areas. Under rare conditions, when the radar is not tracking any vehicles or objects in its path this warning may temporarily occur.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 When the condition that deactivated the system is no longer present, the system will return to the “Adaptive Cruise Control Off” state and will resume function by simply reactivating it. NOTE: • If the “ACC / FCW Unavailable Wipe Front Radar Sensor” message occurs frequently (e.g. more than once on every trip) without any snow, rain, mud, or other obstruction, have the radar sensor realigned at your authorized dealer.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If weather conditions are not a factor, the driver should occurs, try activating ACC again later, following a key examine the windshield and the camera located on the cycle. If the problem persists, see your authorized dealer. back side of the inside rear view mirror. They may Precautions While Driving With ACC require cleaning or removal of an obstruction.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 the vehicle is out of the curve the system will resume your original Set Speed. This is a part of normal ACC system functionality. NOTE: On tight turns ACC performance may be limited. 3 Turns And Bends When driving on a curve with ACC engaged, the system may decrease the vehicle speed and acceleration for stability reasons, with no target vehicle detected.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using ACC On Hills Lane Changing When driving on hills, ACC may not detect a vehicle in your lane. Depending on the speed, vehicle load, traffic conditions, and the steepness of the hills, ACC performance may be limited. ACC may not detect a vehicle until it is completely in the lane in which you are traveling.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 Narrow Vehicles Some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There may not be sufficient distance to the vehicle ahead.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Stationary Objects And Vehicles ACC does not react to stationary objects and stationary vehicles. For example, ACC will not react in situations where the vehicle you are following exits your lane and the vehicle ahead is stopped in your lane. Always be attentive and ready to apply the brakes if necessary. General Information FCC Requirements For Vehicular Radar Systems Classification Specifications: 47 C.F.R. Part 15 47 C.F.R Part 15.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 To change between the different cruise control modes, press the ADAPTIVE CRUISE CONTROL (ACC) ON/ OFF button which turns the ACC and the NORMAL (Fixed Speed) CONTROL OFF. Pressing of the NORMAL (Fixed Speed) CRUISE CONTROL ON/OFF button will result in turning ON (changing to) the Normal (Fixed Speed) Cruise Control mode. WARNING! In the Normal (Fixed Speed) Cruise Control mode, the system will not react to vehicles ahead.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pressing the SET (+) button once will result in a 1 mph While the Normal (Fixed Speed) Cruise Control is set, the (1 km/h) increase in set speed. Each subsequent tap of set speed can be decreased by pressing and holding the SET - button. If the button is continually pressed, the set the button results in an increase of 1 mph (1 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 • The braking temperature exceeds normal range (overheated). FORWARD COLLISION WARNING (FCW) WITH MITIGATION — IF EQUIPPED • The shift lever is removed from the Drive position. Forward Collision Warning (FCW) With Mitigation Operation To Resume Speed The Forward Collision Warning (FCW) system with To resume a previously set speed, push the RES button mitigation provides the driver with audible warnings, and release.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the system determines that a forward collision is probable, the driver will be provided with audible and visual warnings and may provide a brake jerk warning. If the driver does not take action based upon these progressive warnings, then the system will provide a limited level of autonomous braking to help slow the vehicle and mitigate the potential forward collision.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 NOTE: Turning FCW ON Or OFF • The minimum speed for FCW activation is 5 mph NOTE: The default status of FCW is “On”, this allows the system to warn you of a possible collision with the vehicle in (10 km/h). front of you. • The FCW alerts may be triggered on objects other than The forward collision button is located on the switch vehicles such as guard rails or sign posts based on the panel below the Uconnect® display. course prediction.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To turn the FCW system OFF, press the forward collision Changing FCW And Active Braking Status button once to turn the system OFF (led turns on). To change the FCW and Active Braking settings with To turn the FCW system back ON, press the forward Uconnect® 8.4/8.4A System Screen — if equipped. collision button again to turn the system ON (led turns off).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 To change the FCW and Active Braking settings with 6. Press the second “FWD Collision W...” soft-key. Uconnect® 5.0 System Screen — if equipped. 7. Press the “Active Braking” On or Off soft-key. NOTE: The settings can only be changed when the The default status of FCW is the “Far” setting and the vehicle is in PARK.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Although the vehicle is still drivable under normal conditions, the active braking may not be fully available. • The system will retain the last setting selected by the Once the condition that limited the system performance driver after ignition shut down. is no longer present, the system will return to its full • FCW may not react to irrelevant objects such as performance state.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 LANE DEPARTURE WARNING (LDW) — IF EQUIPPED The driver may manually override the haptic warning by applying torque into the steering wheel at any time. Lane Departure Warning (LDW) Operation When only a single lane marking is detected and the driver unintentionally drifts across the lane marking (no turn signal applied), the LDW system provides a visual warning through the instrument cluster to prompt the driver to remain within the lane.
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning LDW ON Or OFF The default status of LDW is “ON”. To turn the LDW system OFF, press the lane departure warning button once to turn the system OFF (LED turns on). To turn the LDW system back ON, press the lane departure The lane departure warning button is located on the warning button again to turn the system ON (LED turns switch panel below the Uconnect® display. off) and a lane sense on display is shown in the EVIC.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 NOTE: The LDW system will retain the last system state ON or OFF from the last ignition cycle when the ignition is changed to the ON/RUN position. LDW Warning Display The LDW system will indicate the current lane drift condition through the Electronic Vehicle Information Center (EVIC). 3 3.5 EVIC Screen — If Equipped When the LDW system is ON; the lane lines are gray when the lane boundaries have not been detected and the LDW indicator is solid white.
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When the LDW system senses the lane has been approached and is in a lane cross situation, the left thick lane line flashes from white to gray, the left thin line remains solid white and the LDW indicator changes from solid white to flashing yellow. Lane Approached (Flashing White to Gray Thick Line/Flashing Yellow Indicator) NOTE: The LDW system operates with the similar behavior for a right lane departure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 • For example: If approaching the left side of the lane the steering wheel will torque to the right. 3 Lanes Sensed (White Lines/Green Indicator) • When the LDW system senses a lane cross situation, the left thick lane line turns solid white, the left thin line remains solid white. The LDW indicator changes from solid green to solid yellow. At this time torque is applied to the steering wheel in the opposite direction of the lane boundary.
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When the LDW system senses the lane has been approached and is in a lane cross situation, the left thick lane line flashes from white to gray, the left thin line remains solid white and the LDW indicator changes from solid yellow to flashing yellow. At this time torque is applied to the steering wheel in the opposite direction of the lane boundary. • For example: If approaching the left side of the lane the steering wheel will torque to the right.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 7.0 EVIC Screen — If Equipped Left Lane Departure — Only Left Lane Detected When the LDW system is ON; the lane lines are gray • When the LDW system is ON, the left line turns from when the lane boundaries have not been detected and the gray to white to indicate that the lane marking has LDW indicator is solid white. been detected.
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When the LDW system senses the lane has been approached and is in a lane cross situation, the left thick lane line flashes yellow (on/off), the left thin line remains solid yellow and the LDW indicator changes from solid white to flashing yellow. Lane Approached (Flashing Yellow Thick Line, Solid Yellow Thin Line/Flashing Yellow Indicator) NOTE: The LDW system operates with the similar behavior for a right lane departure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 • For example: If approaching the left side of the lane the steering wheel will torque to the right. 3 Lanes Sensed (White Lines/Green Indicator) • When the LDW system senses a lane cross situation, the left thick lane line and left thin line turn solid yellow. The LDW indicator changes from solid green to solid yellow. At this time torque is applied to the steering wheel in the opposite direction of the lane boundary.
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When the LDW system senses the lane has been approached and is in a lane cross situation, the left thick lane line flashes yellow (on/off) and the left thin line remains solid yellow. The LDW indicator changes from solid yellow to flashing yellow. At this time torque is applied to the steering wheel in the opposite direction of the lane boundary. • For example: If approaching the left side of the lane the steering wheel will torque to the right.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 Changing LDW Status NOTE: The LDW system settings can be made through the • When enabled the system operates above 37 mph Uconnect® system screen. (60 km/h) and below 100 mph (160 km/h). Follow these steps to change the LDW settings: • Use of the turn signal suppresses the warnings. 1. Press the “Controls” soft-key located on the bottom of • The system will not apply torque to the steering wheel the Uconnect® display. whenever a safety system engages.
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE above. A display warning will appear in the EVIC indicating the vehicle is above ParkSense operating The ParkSense® Rear Park Assist system provides visual and audible indications of the distance between the rear speed. The system will become active again if the vehicle speed is decreased to speeds less than approximately fascia and a detected obstacle when backing up, e.g. during a parking maneuver. Refer to ParkSense® System 6 mph (9 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 ParkSense® Warning Display ParkSense® Display The ParkSense® Warning screen will only be displayed if Sound and Display is selected from the Customer Programmable Features section of the Uconnect® System. Refer to ⬙Uconnect® Settings” in “Understanding Your Instrument Panel” for further information. When the vehicle is in REVERSE, the EVIC will display the park assist ready system status.
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If an obstacle is detected in the left and/or right rear region, the display will show a single flashing arc in the left and/or right rear region and will produce a fast sound tone. As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and the tone will change from fast to continuous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 3 Slow Tone/Solid Arc Fast Tone/Flashing Arc
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fast Tone/Flashing Arc Continuous Tone/Flashing Arc The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 Rear Distance (in/cm) Arcs — Left Arcs — Center Arcs — Right Audible Alert Chime Radio Volume Reduced WARNING ALERTS 59-47 in 47-39 in (150(120120 cm) 100 cm) Greater than 79 in (200 cm) None 79-59 in (200150 cm) None None None 6th Solid None None No 39-25 in (10065 cm) 25-12 in (65-30 cm) Less than 12 in (30 cm) None None 5th Solid 4th Solid None None None 3rd Flashing None Single 1/2Second Tone (for rear center only) Yes Slow (for rear c
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: ParkSense® will reduce the volume of the radio, When the ParkSense® switch is pressed to disable the if on, when the system is sounding an audio tone. system, the instrument cluster will display the “PARKSENSE OFF” message for approximately five seconds. Refer to Enabling And Disabling ParkSense® “Electronic Vehicle Information Center (EVIC)” in “UnderParkSense® can be enabled and disabled with the standing Your Instrument Panel” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 If “PARKSENSE UNAVAILABLE WIPE REAR SENSORS” appears in the Electronic Vehicle Information Center (EVIC) make sure the outer surface and the underside of the rear During vehicle start up, when the ParkSense® Rear Park fascia/bumper is clean and clear of snow, ice, mud, dirt or Assist System has detected a faulted condition, the instruother obstruction and then cycle the ignition.
222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense® System Usage Precautions NOTE: • ParkSense®, when on, will reduce the volume of the radio when it is sounding a tone. • Clean the ParkSense® sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not working • Jackhammers, large trucks, and other vibrations could properly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 • On vehicles equipped with a tailgate, ParkSense® should be disabled when the tailgate is in the lowered or open position and the vehicle is in REVERSE. A lowered tailgate could provide a false indication that an obstacle is behind the vehicle. CAUTION! • ParkSense® is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all.
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) could detect the ball mount and hitch ball assembly, depending on its size and shape, giving a false indication that an obstacle is behind the vehicle. PARKSENSE® FRONT AND REAR PARK ASSIST — IF EQUIPPED The ParkSense® Park Assist system provides visual and audible indications of the distance between the rear and/or front fascia and a detected obstacle when backing up or moving forward, e.g. during a parking maneuver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 If your vehicle is equipped with a Manual Transmission, ParkSense® will retain the last system state (enabled or the automatic braking function in REVERSE gear is not disabled) from the last ignition cycle when the ignition is available. changed to the ON/RUN position. NOTE: • The driver is always responsible for controlling the vehicle. • The system is provided to assist the driver and not to substitute the driver.
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense® Sensors The six ParkSense® sensors, located in the front fascia/ bumper, monitor the area in front of the vehicle that is within the sensors’ field of view. The sensors can detect obstacles from approximately 12 in (30 cm) up to 47 in (120 cm) from the front fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 The ParkSense® Warning screen is located within the Electronic Vehicle Information Center (EVIC). It provides visual warnings to indicate the distance between the rear fascia/bumper and/or front fascia/bumper and the detected obstacle. Refer to “Electronic Vehicle Information Center (EVIC)/Settings” in Understanding Your Instrument Panel” for further information.
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Single 1/2 Second Tone/Solid Arc Slow Tone/Solid Arc
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 3 Slow Tone/Solid Arc Fast Tone/Flashing Arc
230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fast Tone/Flashing Arc Continuous Tone/Flashing Arc The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 Rear Distance (in/cm) Arcs — Left Arcs — Center Arcs — Right Audible Alert Chime Radio Volume Reduced WARNING ALERTS 59-47 in 47-39 in (150(120120 cm) 100 cm) Greater than 79 in (200 cm) None 79-59 in (200-150 cm) None None None 6th Solid None None No 39-25 in (10065 cm) 25-12 in (65-30 cm) Less than 12 in (30 cm) None None 5th Solid 4th Solid None None None 3rd Flashing None Single 1/2Second Tone (for rear center only) Yes Slow (for rear
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: ParkSense® will reduce the volume of the radio, will show the single arc moving closer to the vehicle. A fast sound tone will be produced when reaching the 2nd if on, when the system is sounding an audio tone. flashing arc and will change to a continuous sound tone Front Park Assist when the 1st flashing arc appears.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 3 No Tone/Solid Arc No Tone/Flashing Arc
234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fast Tone/Flashing Arc Continuous Tone/Flashing Arc The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 Front Distance (in/cm) Arcs — Left Arcs — Center Arcs — Right Audible Alert Chime Radio Volume Reduced Greater than 47 in (120 cm) None None None None No WARNING ALERTS 47-39 in 39-25 in (120-100 cm) (100-65 cm) None None 4th Solid 3rd Flashing None None None None No No 25-12 in (65-30 cm) 2nd Flashing 2nd Flashing 2nd Flashing Fast Less than 12 in (30 cm) 1st Flashing 1st Flashing 1st Flashing Continuous Yes Yes NOTE: ParkSense® will reduce the volume
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the Uconnect® System is equipped, chime volume settings will not be accessible from the EVIC. The chime volume settings include LOW, MEDIUM, and HIGH. The factory default volume setting is MEDIUM. ParkSense will retain its last known configuration state through ignition cycles. Enabling And Disabling ParkSense® ParkSense® can be enabled and disabled with the ParkSense® switch, located on the switch panel below the Uconnect® display.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 REVERSE and the system is disabled, the EVIC will has detected a faulted condition, the EVIC will display a display the “PARKSENSE OFF” message for as long as ⬙PARKSENSE UNAVAILABLE WIPE REAR SENSORS⬙, ⬙PARKSENSE UNAVAILABLE WIPE FRONT SENSORS⬙ the vehicle is in REVERSE. or ⬙PARKSENSE UNAVAILABLE SERVICE REQUIRED⬙ The ParkSense® switch LED will be ON when ParkSense® pop up message for five seconds. After five seconds, a car is disabled or requires service.
238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If ⬙PARKSENSE UNAVAILABLE WIPE REAR SENSORS⬙ or ⬙PARKSENSE UNAVAILABLE WIPE FRONT SENSORS⬙ appears in the Electronic Vehicle Information Center (EVIC) make sure the outer surface and the underside of the rear fascia/bumper and/or front fascia/bumper is clean and clear of snow, ice, mud, dirt or other obstruction and then cycle the ignition. If the message continues to appear see an authorized dealer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239 • ParkSense®, when on, will reduce the volume of the • On vehicles equipped with a tailgate, ParkSense® should be disabled when the tailgate is in the lowered radio when it is sounding a tone. or open position. A lowered tailgate could provide a • Clean the ParkSense® sensors regularly, taking care false indication that an obstacle is behind the vehicle. not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris.
240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) WARNING! (Continued) • The vehicle must be driven slowly when using ParkSense® in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using ParkSense®. • Before using ParkSense®, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241 PARKSENSE® ACTIVE PARK ASSIST SYSTEM — IF EQUIPPED NOTE: • The driver is always responsible for controlling the The ParkSense® Active Park Assist system is intended to vehicle, responsible for any surrounding objects, and assist the driver during parallel and perpendicular parkmust intervene as required.
242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Enabling And Disabling The ParkSense® Active Park Assist System To enable the ParkSense® Active Park Assist system, press the ParkSense® Active Park Assist switch once (LED turns on). The ParkSense® Active Park Assist system can be enabled and disabled with the ParkSense® Active Park To disable the ParkSense® Active Park Assist system, Assist switch, located on the switch panel below the press the ParkSense® Active Park Assist switch again Uconnect® display.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243 • Pressing the ParkSense® Front and Rear Park Assist • Driver’s door is closed switch • Rear liftgate is closed • Driver’s door is opened • Vehicle speed is less than 15 mph (25 km/h) • Rear liftgate is opened NOTE: If the vehicle is driven above approximately • Electronic Stability Control / Anti-lock Braking Sys- 15 mph (25 km/h), the EVIC will instruct the driver to tem intervention slow down.
244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Parallel Parking Space Assistance Operation/ Display When the ParkSense® Active Park Assist system is enabled the “Active ParkSense Searching - Press OK for Perpendicular Park” message will appear in the EVIC display. You may switch to perpendicular parking if you desire. Push the OK button on the left side steering wheel switch to change your parking space setting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245 NOTE: • It is the driver’s responsibility to use the brake and accelerator during the semi-automatic parking maneuver. • When the system instructs the driver to remove their hands, the driver should check their surroundings and begin to back up slowly. • The ParkSense® Active Park Assist system allows up to 6 parking attempts to be made.
246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If the system is canceled during the maneuver for any reason, the driver must take control of the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247 When the vehicle has been moved into the parallel park position you will be instructed to place the shift lever into the DRIVE position, move forward slowly and check your surroundings. After moving forward and checking your surroundings you may be instructed to place the shift lever into the REVERSE position and move backward slowly into position while you check your surroundings.
248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your vehicle is now in the parallel park position. When the maneuver is complete, the driver will be instructed to check the vehicle’s parking position. If the driver is satisfied with the vehicle position, they should shift to PARK. The ⬙Active ParkSense Complete - Check Parking Position⬙ message will be momentarily displayed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 249 • The driver needs to make sure that the selected parking space for the maneuver remains free and clear of any obstructions (e.g. pedestrians, bicycles, etc.) • The driver is responsible to ensure that the selected parking space is suitable for the maneuver and free/ clear of anything that may be overhanging or protruding into the parking space (e.g., ladders, tailgates, etc.
250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • It is the driver’s responsibility to use the brake and accelerator during the semi-automatic parking maneuver. • When the system instructs the driver to remove hands, the driver should check their surroundings and begin to back up slowly. • The ParkSense® Active Park Assist system allows up to 6 parking attempts to be made.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 251 3 Parking Space Found — Shift To Reverse Check Entire Surroundings — Remove Hands From Steering Wheel
252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the vehicle has been moved into the perpendicular park position you will be instructed to place the shift lever into the DRIVE position, move forward slowly, and check your surroundings. After moving forward and checking your surroundings you may be instructed to place the shift lever into the REVERSE position and move backward slowly into position while you check your surroundings.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253 Your vehicle is now in the perpendicular park position. When the maneuver is complete, the driver will be instructed to check the vehicle’s parking position. If the driver is satisfied with the vehicle position, they should shift to PARK. The ⬙Active ParkSense Complete - Check Parking Position⬙ message will be momentarily displayed.
254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Drivers must be careful when performing parallel or perpendicular parking maneuvers even when using the ParkSense Active Park Assist system. Always check carefully behind and in front of your vehicle, look behind and in front of you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up and moving forward.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255 PARKVIEW® REAR BACK UP CAMERA — IF EQUIPPED Your vehicle may be equipped with the ParkView® Rear Back Up Camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into REVERSE. The image will be displayed in the touchscreen display along with a caution note to “check entire surroundings” across the top of the screen. After five seconds this note will disappear.
256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The following table shows the approximate distances for each zone: Zone Red Yellow Green Distance to the rear of the vehicle 0 - 1 ft (0 - 30 cm) 1 ft - 3 ft (30 cm - 1 m) 3 ft or greater (1 m or greater) WARNING! CAUTION! Drivers must be careful when backing up even when using the ParkView® Rear Back Up Camera.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257 NOTE: If snow, ice, mud, or any foreign substance builds Turning ParkView® On Or Off — With up on the camera lens, clean the lens, rinse with water, Uconnect® 8.4A/8.4AN and dry with a soft cloth. Do not cover the lens. 1. Press the “Settings” soft-key. Turning ParkView® On Or Off — With 2. Press the “Safety & Driving Assistance” soft-key. Uconnect® 5.0 3. Press the check box soft key next to “Parkview® 1. Press the “Settings” button.
258 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink® buttons that are located in the headliner Before You Begin Programming HomeLink® or sun visor designate the three different HomeLink® Be sure that your vehicle is parked outside of the garage channels. before you begin programming.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 259 NOTE: • Erasing all channels should only be performed when programming HomeLink® for the first time. Do not erase channels when programming additional buttons. • If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. Programming A Rolling Code For programming garage door openers that were manufactured after 1995.
260 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Cycle the ignition to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator light in view. Firmly press and release the “LEARN” or “TRAINING” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the LEARN/TRAIN mode. NOTE: You have 30 seconds in which to initiate the next 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 261 Reprogramming A Single HomeLink® Button Programming A Non-Rolling Code To reprogram a channel that has been previously trained, For programming Garage Door Openers manufactured follow these steps: before 1995. 1. Turn the ignition switch to the ON/RUN position. 1. Cycle the ignition to the ON/RUN position. 2. Press and hold the desired HomeLink® button until 2.
262 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Press and hold the programmed HomeLink® button and observe the indicator light. • If the indicator light stays on constantly, programming is complete and the garage door/device should activate when the HomeLink® button is pressed. • To program the remaining two HomeLink® buttons, repeat each step for each remaining button. DO NOT erase the channels. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 263 It may be helpful to unplug the device during the cycling 5. Press and hold the programmed HomeLink® button and observe the indicator light. process to prevent possible overheating of the garage door or gate motor. • If the indicator light stays on constantly, programming is complete and the garage door/device should 1. Cycle the ignition to the ON/RUN position. activate when the HomeLink® button is pressed. 2.
264 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Without releasing the button proceed with “Canadian/ The HomeLink® Universal Transceiver is disabled when Gate Operator Programming” Step 2 and follow all the Vehicle Security Alarm is active. remaining steps. Troubleshooting Tips Using HomeLink® If you are having trouble programming HomeLink®, To operate, press and release the programmed HomeLink® button. Activation will now occur for the programmed device (i.e.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 265 WARNING! • Your motorized door or gate will open and close while you are programming the universal transceiver. Do not program the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982.
266 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF WITH POWER SHADE — IF EQUIPPED The power sunroof switch is located to the left between the sun visors on the overhead console. The power shade switch is located to the right between the sun visors on the overhead console. WARNING! • Never leave children unattended in a vehicle, and do not leave the key in the ignition switch (or leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/Run position).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 267 halfway to the comfort stop position. Press the switch rearward and release it again, the sunroof and sunshade will open fully and stop automatically. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof. Closing Sunroof — Express Press the switch forward and release it within one-half second and the sunroof will close automatically from any position.
268 UNDERSTANDING THE FEATURES OF YOUR VEHICLE switch a second time from the halfway position and the shade will automatically open to the full open position Press and release the ⬙Vent⬙ button within one-half secand stop automatically. This is called “Express Open”. ond and the sunroof will open to the vent position. This During Express Open operation, any movement of the is called “Express Vent”, and it will occur regardless of shade switch will stop the shade. sunroof position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 269 Closing Power Shade — Express Pinch Protect Feature Press the switch forward and release it within one-half second and the shade will close automatically from any position. The shade will close fully and stop automatically. This is called “Express Close”. During Express Close operation, any movement of the switch will stop the shade. This feature will detect an obstruction in the opening of the sunroof during Express Close operation.
270 UNDERSTANDING THE FEATURES OF YOUR VEHICLE open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 271 • Opening and closing the Sky Slider™ repeatedly without the engine running may run the battery down. CAUTION! Failure to follow these cautions can cause damage to the Sky Slider™ vehicle contents, and the vehicle interior: • Never attempt to open or close the Sky Slider™ when it is frozen. Wait until the Sky Slider™ is thawed before operating.
272 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • Before operating the Sky Slider™ make sure that no moving parts of the Sky Slider™ can injure a person or animal. • Never place any extremities (hands, feet, etc.) near the Sky Slider™ components or the roof area while operating the Sky Slider™. • If potential danger exists while opening or closing the Sky Slider™ in Automatic Mode, press and release the switch immediately to interrupt the operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 273 Opening The Sky Slider™ Using Operator Mode Press the switch rearward and hold it, the Sky Slider™ will open from the front and move toward the rear of the Press the switch rearward and release it within onevehicle. half second and the Sky Slider™ will open from the front and move automatically toward the rear of the vehicle.
274 UNDERSTANDING THE FEATURES OF YOUR VEHICLE and turn the wrench clockwise until the top closes completely. The left motor facing forward will close the If the Sky Slider™ is open from the front, press the switch top when it is open from the rear of the vehicle. The right forward and hold it, the Sky Slider™ will move forward. motor will close the top when it is open from the front of Release the switch to stop the Sky Slider™ travel at any the vehicle. point.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 275 Wind Buffeting ELECTRICAL POWER OUTLETS Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the Sky Slider™ in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows together to minimize the buffeting.
276 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlets as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your New Vehicle Limited Warranty. The front power outlet is located inside the storage area on the center stack of the instrument panel. Push inward on the storage lid to open the compartment and gain access to this power outlet.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 277 The rear power outlet is located in the right rear cargo area. WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure.
278 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 279 To turn on the power inverter outlet, simply plug in the WIRELESS CHARGING PAD — IF EQUIPPED device. The outlet automatically turns off when the device is unplugged. The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset.
280 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your mobile phone must be designed for Qi wireless 3. Use the adjustable cradle to hold the mobile phone in position. The cradle moves by pushing down on the charging, be equipped with an aftermarket sleeve or finger tabs and moving the cradle in or out. equipped with a back plate from your mobile phone provider. The wireless charging pad is equipped with an anti-slip mat, an adjustable cradle to hold your mobile phone in place and an LED indicator light.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 281 The LED indicator will flash green while the mobile phone is charging. The Qi enabled phone is able to function normally as it is charging. If the LED indicator begins flashing red, see your authorized dealer. CAUTION! Do not place your vehicle key fob on the wireless charging pad, the Keyless Enter-N-Go™ feature may not work properly while a mobile phone is being charged.
282 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS There are two cupholders for the front seat passengers, located in the center console. Rear Cupholders STORAGE Glove Box Storage Compartment Front Cupholders The glove box storage compartment is located on the There are two cupholders for the rear seat passengers, right side of the instrument panel. Pull outward on the located in the center armrest. latch to open the storage compartment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 283 Their is also an additional storage bin located above the Console Storage Compartment instrument panel in the center of the dash. Some vehicles may be equipped with a wireless charging pad located in the upper portion of the center console. Refer to Wireless Charging Pad-If Equipped in this section for more information.
284 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open, pull up on the latch and lift the cover. The center console has a storage area which can hold cell phones, PDAs, and other small items.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 285 WARNING! Do not operate this vehicle with a console compartment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distraction, resulting in death or injury. Rear Storage Bin The rear storage bins are located in the rear of the vehicle on the sides of the load floor.
286 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Tie-Down Hooks And Loops The tie-downs located on the cargo area floor should be used to secure loads safely when the vehicle is moving. Cargo tie-down loops are located on the trim panels. WARNING! • Cargo tie-downs are not safe anchors for a child seat tether strap. In a sudden stop or accident, a tie-down could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 287 WARNING! (Continued) • Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or become a dangerous projectile in a sudden stop or accident. 3 Retractable Cargo Area Cover — If Equipped NOTE: The purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo.
288 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The cover rolls away neatly inside its housing when not in use. You can also remove the cover from the vehicle to make more room in the cargo area. To install the cover, position it in the vehicle so that the flat side of the housing faces upward. Then, insert the right spring-loaded post (located on the end of the cover housing) into the right attachment points. WARNING! In a collision, a cargo cover loose in the vehicle could cause injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 289 To use the washer, push the lever forward and hold while spray is desired. If the lever is pushed while in the intermittent setting, the wiper will turn on and operate for several wipe cycles after the end of the lever is released, and then resume the intermittent interval previously selected. If the lever is pushed while the wiper is in the off position, the wiper will operate for several wipe cycles, then turn off.
290 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Window Defroster The rear window defroster button is located on the switch bank by the manual climate controls. Press this button to turn on the rear window defroster and the heated outside mirrors. An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 291 ROOF LUGGAGE RACK — IF EQUIPPED NOTE: Roof rack and crossbars cannot be used on vehicles equipped with Skyslider®. The load carried on the roof, when equipped with a luggage rack, must not exceed 150 lbs (68 kg), and it should be uniformly distributed over the cargo area. Crossbars should always be used whenever cargo is placed on the roof rack. Check the straps frequently to be sure that the load remains securely attached.
292 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Cargo must be securely tied down before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof rack cautions when carrying cargo on your roof rack.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 INSTRUMENT PANEL FEATURES . . . . . . . . . .295 䡵 INSTRUMENT CLUSTER — BASE . . . . . . . . . .296 䡵 INSTRUMENT CLUSTER . . . . . . . . . . . . . . . . .297 䡵 INSTRUMENT CLUSTER DESCRIPTIONS . . . . .298 䡵 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) . . . . . . . . . . . . . . . . . . . . . . . .305 ▫ Electronic Vehicle Information Center (EVIC) Displays — 3.5” Display. . . . . . . . . . . . . . . . .
294 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 iPod®/USB/MP3 CONTROL — IF EQUIPPED . .359 䡵 STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . . . .360 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . .360 ▫ CD Player . . . . . . . . . . . . . . . . . . . . . . . . . . .361 䡵 CD/DVD DISC MAINTENANCE . . . . . . . . . . .361 䡵 RADIO OPERATION AND MOBILE PHONES . .362 䡵 CLIMATE CONTROLS . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 295 INSTRUMENT PANEL FEATURES 4 1 — Air Demister Outlet 2 — Air Outlet 3 — Electronic Vehicle Information Center (EVIC) Controls 4 — Horn / Driver Air Bag 5 6 7 8 — — — — Instrument Cluster Electronic Speed Controls Storage Compartment Radio 9 — Passenger Air Bag 10 — Glove Compartment 11 — Lower Switch Bank 12 — Uconnect® Hard Controls / Climate Controls 13 14 15 16 — — — — Stop/Start Ignition Button Trunk Release Button Dimmer Switches Headlight Switch
296 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — BASE
UNDERSTANDING YOUR INSTRUMENT PANEL 297 INSTRUMENT CLUSTER 4
298 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Tachometer 5. Electronic Vehicle Information Center (EVIC) Display/ Odometer Display Indicates the engine speed in revolutions per minute The odometer display shows the total distance the vehicle has been driven. (RPM x 1000). U.S. Federal regulations require that upon transfer of 2. High Beam Indicator vehicle ownership, the seller certify to the purchaser the Indicates that headlights are on high beam.
UNDERSTANDING YOUR INSTRUMENT PANEL 299 When the appropriate conditions exist, this display shows 7. Electronic Stability Control (ESC) OFF Indicator the Electronic Vehicle Information Center (EVIC) messages. Light — If Equipped Refer to “Electronic Vehicle Information Center”. This light indicates the Electronic Stability Con6. Anti-Lock Brake (ABS) Light trol (ESC) is off. This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition 8.
300 UNDERSTANDING YOUR INSTRUMENT PANEL either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer The “ESC Off Indicator Light” and the “ESC Activation/ as soon as possible. Refer to “Occupant Restraints” in Malfunction Indicator Light” come on momentarily each “Things To Know Before Starting Your Vehicle” for further time the ignition switch is turned to ON/RUN. information. Each time the ignition is turned to ON/RUN, the ESC 11.
UNDERSTANDING YOUR INSTRUMENT PANEL 301 12. Turn Signal Indicator The arrows will flash with the exterior turn signals when the turn signal lever is operated. A tone will chime, and an EVIC message will appear if either turn signal is left on for more than 1 mile (1.6 km). NOTE: If either indicator flashes at a rapid rate, check for a defective outside light bulb. 13.
302 UNDERSTANDING YOUR INSTRUMENT PANEL Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists.
UNDERSTANDING YOUR INSTRUMENT PANEL 303 15. Temperature Gauge CAUTION! (Continued) The temperature gauge shows engine coolant temperature. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily. remains on the “H” and you hear continuous chimes, turn the engine off immediately and call an authorized dealer for service. The gauge pointer will likely indicate a higher temperature when driving in hot weather, up mountain grades, or when towing a trailer.
304 UNDERSTANDING YOUR INSTRUMENT PANEL 16. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system called OBD II that monitors engine and automatic transmission control systems. The light will illuminate when the key is in the ON/RUN position before engine start. If the bulb does not come on when turning the key from OFF to ON/RUN, have the condition checked promptly. Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc.
UNDERSTANDING YOUR INSTRUMENT PANEL 305 17. Vehicle Security Light This light will flash rapidly for approximately 15 seconds when the vehicle theft alarm is arming. The light will flash at a slower speed continuously after the alarm is set. The security light will also come on for about three seconds when the ignition is first turned on.
306 UNDERSTANDING YOUR INSTRUMENT PANEL • Driver Assist • Fuel Economy Info • Trip (Trip A/Trip B) The system allows the driver to select information by pressing the following buttons mounted on the steering wheel: • Stop/Start • Audio Info • Messages • Screen Setup • Speed Warning EVIC Buttons
UNDERSTANDING YOUR INSTRUMENT PANEL 307 • UP Arrow Button • RIGHT Arrow Button Press and release the RIGHT arrow button to Press and release the UP arrow button to scroll access the information screens or sub-menu upward through the main menu and submenus screens of a main menu item. (Main Gauge, MPH/km/h, Vehicle Info, Terrain, Driver Assist, Fuel Economy, Trip A, Trip B, • BACK/LEFT Arrow Button Audio, Stored Messages, Screen Set Up).
308 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Vehicle Information Center (EVIC) Displays — 3.5” Display The EVIC displays are located in the center portion of the cluster and consists of eight sections: 1. Brake Warning Light — If Equipped This light monitors various brake functions, including brake fluid level and parking brake application.
UNDERSTANDING YOUR INSTRUMENT PANEL 309 The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected.
310 UNDERSTANDING YOUR INSTRUMENT PANEL Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for approximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer.
UNDERSTANDING YOUR INSTRUMENT PANEL 311 4. Reconfigurable Telltail Display Area The main display area will normally display the main menu or the screens of a selected feature of the main menu. The main display area also displays “pop up” messages that consist of approximately 60 possible warning or information messages.
312 UNDERSTANDING YOUR INSTRUMENT PANEL 5. Lane Departure Warning (LDW) 6. Brake Warning Light The Lane Departure Warning (LDW) system provides the driver with visual and steering torque warnings when the vehicle starts to drift out of its lane unintentionally without the use of a turn signal. When the LDW system is ON and ready the lane lines and LDW indicator are the color gray. When the LDW system is armed, the lane lines change to white and the LDW indicator changes to green.
UNDERSTANDING YOUR INSTRUMENT PANEL 313 The dual brake system provides a reserve braking capacWARNING! (Continued) ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately.
314 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: This light shows only that the parking brake is 10. Reconfigurable Telltale Display applied. It does not show the degree of brake application. • Transmission Temperature Warning Light This light indicates that there is excessive trans7. Fuel Gauge mission fluid temperature that might occur Fuel Gauge displays the level of fuel in the fuel tank with severe usage such as trailer towing. It may when the ignition switch is in the ON/RUN position.
UNDERSTANDING YOUR INSTRUMENT PANEL 315 • Adaptive Cruise Control (ACC) Malfunction This light will turn on when a ACC is not operating and needs service. For further inforIf you continue operating the vehicle when the mation, refer to “Adaptive Cruise Control Transmission Temperature Warning Light is illumi(ACC)” in “Understanding The Features Of nated you could cause the fluid to boil over, come in Your Vehicle.” contact with hot engine or exhaust components and cause a fire.
316 UNDERSTANDING YOUR INSTRUMENT PANEL • Selec Speed Control Indicator — If Equipped The symbol illuminates and is active only in This area displays the dedicated speed warn4WD Low range when either the HDC switch ing telltale. on the instrument panel is selected or ROCK mode for Selec-Terrain is selected. 12. Speed For Electronic Cruise Control Setting If the T-case is not in 4WD Low range, the following This displays the set speed of the Electronic message is displayed “Selec-Speed Unavailable”.
UNDERSTANDING YOUR INSTRUMENT PANEL 317 14. Reconfigurable Telltale Display • Power Steering System Over Temperature — If Equipped If the “POWER STEERING SYSTEM OVER TEMP” message and a icon are displayed on the EVIC screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system. You will lose power steering assistance momentarily until the over temperature condition no longer exists.
318 UNDERSTANDING YOUR INSTRUMENT PANEL • Oil Pressure Warning Light This light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood.
UNDERSTANDING YOUR INSTRUMENT PANEL 319 required. You may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. • Oil Temperature Warning Light This telltale indicates engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. For further information on four-wheel drive operation and proper use, refer to “Four-Wheel Drive Operation — If Equipped” in “Starting And Operating”. 15.
320 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H” and you hear continuous chimes, turn the engine off immediately and call an authorized dealer for service. WARNING! A hot engine cooling system is dangerous.
UNDERSTANDING YOUR INSTRUMENT PANEL 321 1. Lane Departure Warning (LDW) 2. EVIC Selectable Display Area The Lane Departure Warning (LDW) system provides the driver with visual and steering torque warnings when the vehicle starts to drift out of its lane unintentionally without the use of a turn signal. When the LDW system is ON and ready the lane lines and LDW indicator are the color gray. When the LDW system is armed, the lane lines change to white and the LDW indicator changes to green.
322 UNDERSTANDING YOUR INSTRUMENT PANEL If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the condition has been corrected.
UNDERSTANDING YOUR INSTRUMENT PANEL 323 Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for approximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer.
324 UNDERSTANDING YOUR INSTRUMENT PANEL • Unstored Messages Until RUN These messages deal primarily with the Remote Start feature. This message type is displayed until the ignition is in the RUN state. Examples of this message type are “Remote Start Aborted - Door Ajar” and “Press Brake Pedal and Push Button to Start”. • Five Second Unstored Messages When the appropriate conditions occur, this type of message takes control of the main display area for five seconds and then returns to the previous screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 325 • Selec Speed Control Indicator — If Equipped The symbol illuminates and is active only in 4WD Low range when either the HDC switch on the instrument panel is selected or ROCK mode for Selec-Terrain is selected. If the T-case is not in 4WD Low range, the following message is displayed “Selec-Speed Unavailable”. • Electronic Speed Control ON This light will turn on when the electronic speed control is ON.
326 UNDERSTANDING YOUR INSTRUMENT PANEL 12. Amber Reconfigurable Telltale Display WARNING! • Transmission Temperature Warning Light This light indicates that there is excessive trans- If you continue operating the vehicle when the mission fluid temperature that might occur Transmission Temperature Warning Light is illumiwith severe usage such as trailer towing.
UNDERSTANDING YOUR INSTRUMENT PANEL 327 • Low Coolant Level Indicator • SERV 4WD Indicator Light — If Equipped This telltale will turn on to indicate the vehicle This light alerts the driver that the 4WD is in need of coolant level is low. service. If this light is illuminated, see your authorized dealer as soon as possible.
328 UNDERSTANDING YOUR INSTRUMENT PANEL 13. Odometer Display / Fuel Gauge / Temperature Gauge / Submenu Area The odometer display shows the total distance the vehicle has been driven. U.S. Federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. If your odometer needs to be repaired or serviced, the repair technician should leave the odometer reading the same as it was before the repair or service.
UNDERSTANDING YOUR INSTRUMENT PANEL 329 CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H” and you hear continuous chimes, turn the engine off immediately and call an authorized dealer for service. WARNING! A hot engine cooling system is dangerous.
330 UNDERSTANDING YOUR INSTRUMENT PANEL • Power Steering System Over Temperature — If Equipped If the “POWER STEERING SYSTEM OVER TEMP” message and a icon are displayed on the EVIC screen, it indicates that extreme steering maneuvers may have occurred, which caused an over temperature condition in the power steering system. You will lose power steering assistance momentarily until the over temperature condition no longer exists. Once driving conditions are safe, then pull over and let vehicle idle.
UNDERSTANDING YOUR INSTRUMENT PANEL 331 • Oil Pressure Warning Light This light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood.
332 UNDERSTANDING YOUR INSTRUMENT PANEL required. You may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. • Oil Temperature Warning Light This telltale indicates engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible.
UNDERSTANDING YOUR INSTRUMENT PANEL 333 NOTE: If the indicator message illuminates when you • Service Antilock Brake System start the vehicle, the oil change indicator system did not • Service Electronic Throttle Control reset. If necessary, repeat this procedure.
334 UNDERSTANDING YOUR INSTRUMENT PANEL • Service Electronic Throttle Control • Remote Start Aborted Hood Open • Lights On • Remote Start Aborted Tailgate Open • Right Turn Signal Light Out • Remote Start Aborted Time Expired • Left Turn Signal Light Out • Remote Start Disabled Start to Reset • Turn Signal On • Service Airbag System • Vehicle Not in Park • Service Airbag Warning Light • Key in Ignition • Driver Seatbelt Unbuckled • Key in Ignition Lights On • Passenger Seatbelt Unbuckled •
UNDERSTANDING YOUR INSTRUMENT PANEL 335 • Shift Not Allowed • Shift to Neutral then Drive or Reverse • Autostick Unavailable Service Required • Automatic Unavailable Use Autostick Service Req. • Transmission Getting Hot Press Brake • Trans.
336 UNDERSTANDING YOUR INSTRUMENT PANEL Press and release the UP or DOWN arrow button until “Tire Pressure” is highlighted in the EVIC. Press and Press and release the UP or DOWN arrow button release the RIGHT arrow button and one of the following until the Vehicle Info icon is highlighted in the will be displayed: EVIC. Press and release the RIGHT arrow button and Coolant Temp will be displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL 337 Refer to “Tire Pressure Monitoring System (TPMS)” Fuel Economy under “Starting and Operating” for further information. Press and release the UP or DOWN arrow button until the Fuel Economy icon is highlighted. Trip Info Press and release the UP or DOWN arrow button until the Trip icon is highlighted in the EVIC (Toggle left or • Average Fuel Economy/Miles Per Gallon (MPG or right to select Trip A or Trip B).
338 UNDERSTANDING YOUR INSTRUMENT PANEL Audio Screen Setup Driver Selectable Items Press and release the UP or DOWN arrow button until the Audio display icon is highlighted in the EVIC. Press and release the RIGHT arrow button to scroll through the sub-menus and press the OK button display the active source. Gear Display Screen Setup • None Press and release the UP or DOWN arrow button until the Screen Setup display icon is highlighted in the EVIC.
UNDERSTANDING YOUR INSTRUMENT PANEL 339 • Time • Average MPG • Range To Empty (RTE) • Current MPG • Average MPG • Trip A • Current MPG • Trip B • Trip A Restore To Defaults (Restores All Settings To Default Settings) • Trip B Upper Right • None • Compass (default setting) • Outside Temp • Oil Temp • Time • Range To Empty (RTE) • Cancel • Okay Center • None • Compass • Outside Temp.
340 UNDERSTANDING YOUR INSTRUMENT PANEL • Range to Empty • Average MPG • Current MPG • Trip A • Trip B • Audio Information • Menu Title Uconnect® ACCESS SETTINGS Uconnect® Access 5.0 soft-keys and hard-keys The Uconnect® Access system uses a combination of soft and hard keys located on the center of the instrument 1 — Uconnect® Access Soft-Keys panel that allows you to access and change the customer 2 — Uconnect® Access Hard-Keys programmable features.
UNDERSTANDING YOUR INSTRUMENT PANEL 341 Hard-Keys Hard-Keys are located below the Uconnect® Access system in the center of the instrument panel. In addition, there is a Scroll/Enter control knob located on the right side of the Climate Controls in the center of the instrument panel. Turn the control knob to scroll through menus and change settings (i.e., 30, 60, 90), press the center of the control knob one or more times to select or change a setting (i.e., ON, OFF).
342 UNDERSTANDING YOUR INSTRUMENT PANEL next to the setting, showing that setting has been selected. Once the setting is complete either press the Back Soft-Keys are accessible on the Uconnect® Access display. Arrow soft-key or the Back hard-key to return to the Customer Programmable Features — previous menu or press the X soft-key to close out of the Uconnect® 5.0/8.4 Settings settings screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 343 • Display Brightness With Headlights ON language soft-key until a check-mark appears next to the language, showing that setting has been selected. Touch When in this display, you may select the brightness with the back arrow soft-key to return to the previous menu. the headlights on. Adjust the brightness with the + and – setting soft-keys or by selecting any point on the scale • Units between the + and – soft-keys.
344 UNDERSTANDING YOUR INSTRUMENT PANEL • Touchscreen Beep Clock When in this display, you may turn on or shut off the sound heard when a touch screen button (soft-key) is pressed. Touch the Touchscreen Beep soft-key until a check-mark appears next to the setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu. After pressing the Clock soft-key the following settings will be available.
UNDERSTANDING YOUR INSTRUMENT PANEL 345 • Set Time Minutes • Forward Collision Warning (FCW) — If Equipped The Front Collision Warning (FCW) feature can be can be set to Far, or set to Near. The default status of FCW is the Far setting. This means the system will warn you of a possible collision with the vehicle in front of you when you are farther away. This gives you the most reaction time. To change the setting for more dynamic driving, select the Near setting.
346 UNDERSTANDING YOUR INSTRUMENT PANEL • Forward Collision Warning (FCW) Active Braking — If Equipped The FCW system includes Advanced Brake Assist (ABA). When this feature is selected, it will apply the brakes to slow your vehicle in case of potential forward collision. The ABA applies additional brake pressure when the driver requests insufficient brake pressure to avoid a potential frontal collision. The ABA system becomes active at 5 mph (8 km/h).
UNDERSTANDING YOUR INSTRUMENT PANEL 347 • ParkSense® Active Park Assist — If Equipped Refer to “EVIC settings” or “Uconnect® Settings” in “Understanding Your Instrument Panel” for further The Rear Park Assist system will scan for objects behind information. the vehicle when the transmission shift lever is in REVERSE and the vehicle speed is less than 11 mph • ParkSense® Rear Park Assist Chime Volume — If (18 km/h). The system can be enabled with Sound Only, Equipped or Sound and Display.
348 UNDERSTANDING YOUR INSTRUMENT PANEL Refer to “ParkSense® Rear Park Assist” in “Understand- When this mode is selected, the Blind Spot Monitor ing The Features Of Your Vehicle” for system function (BSM) system is activated and will only show a visual alert in the outside mirrors. When “Lights & Chime” and operating information.
UNDERSTANDING YOUR INSTRUMENT PANEL 349 • ParkView® Rear Backup Camera — If Equipped Your vehicle may be equipped with the ParkView® Rear Back Up Camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into REVERSE. The image will be displayed on the radio touchscreen display along with a caution note to “check entire surroundings” across the top of the screen. After five seconds, this note will disappear.
350 UNDERSTANDING YOUR INSTRUMENT PANEL • Rain Sensing Auto Wipers • Electric Park Brake Service Mode When this feature is selected, the system will automatically activate the windshield wipers if it senses moisture on the windshield. To make your selection, touch the Rain Sensing soft-key, until a check-mark appears next to setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 351 • Headlight Illumination On Approach When this feature is selected, the headlights will activate and remain on for 0, 30, 60, or 90 seconds when the doors are unlocked with the Remote Keyless Entry (RKE)transmitter. To change the Illuminated Approach status, touch the + or - soft-key to select your desired time interval. Touch the back arrow soft-key to return to the previous menu.
352 UNDERSTANDING YOUR INSTRUMENT PANEL • Flash Headlights With Lock On Exit soft-key, until a check-mark appears next to setting, showing that setting has been selected. Touch the When this feature is selected, the headlights will flash back arrow soft-key to return to the previous menu. when the doors are locked or unlocked with the Remote Keyless Entry (RKE) transmitter.
UNDERSTANDING YOUR INSTRUMENT PANEL 353 • 1st Press Of Key Fob Unlocks touching the handle more than once will only result in the driver’s door opening. If driver door first is selected, once When 1st Press Of Key Fob Unlocks is selected, only the the driver door is opened, the interior door lock/unlock driver’s door will unlock on the first press of the Remote switch can be used to unlock all doors (or use RKE Keyless Entry (RKE) transmitter UNLOCK button. When transmitter).
354 UNDERSTANDING YOUR INSTRUMENT PANEL • Memory To FOB — If Equipped • Horn With Remote Start This feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. To make your selection, touch the Memory Linked To FOB soft-key, until a check-mark appears next to setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 355 when exiting the vehicle. To change the Headlight Off Delay status touch the + or - soft-key to select your After pressing the Engine Off Options soft-key the foldesired time interval. Touch the back arrow soft-key to lowing settings will be available. return to the previous menu.
356 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Keep magnetic materials away from the top of the instrument panel, such as iPod’s, Mobile Phones, Laptops and Radar Detectors. This is where the compass module is located, and it can cause interference with the compass sensor, and it may give false readings. • Perform Compass Calibration Touch the Calibration soft-key to change this setting. This compass is self-calibrating, which eliminates the need to manually reset the compass.
UNDERSTANDING YOUR INSTRUMENT PANEL 357 • Equalizer • Surround Sound — If Equipped When in this display you may adjust the Bass, Mid and Treble settings. Adjust the settings with the + and – setting soft-keys or by selecting any point on the scale between the + and – soft-keys. Then touch the arrow back soft-key. This feature provides simulated surround sound mode. To make your selection, touch the Surround Sound soft-key, select On or Off followed by pressing the arrow back soft-key.
358 UNDERSTANDING YOUR INSTRUMENT PANEL Touch the Subscription Info soft-key to access the SubAfter pressing the SIRIUS Setup soft-key the following scription Information screen. settings will be available. Write down the SIRIUS ID numbers for your receiver. To reactivate your service, either call the number listed on • Channel Skip the screen or visit the provider online.
UNDERSTANDING YOUR INSTRUMENT PANEL 359 iPod®/USB/MP3 CONTROL — IF EQUIPPED Located in the front storage area, this feature allows an iPod® or external USB device to be plugged into the USB port. iPod® control supports Mini, 4G, Photo, Nano, 5G iPod® and iPhone® devices. Some iPod® software versions may not fully support the iPod® control features. Please visit Apple’s website for software updates. For further information, refer to the Uconnect® User’s Manual.
360 UNDERSTANDING YOUR INSTRUMENT PANEL The right-hand control is a rocker-type switch with a pushbutton in the center and controls the volume and The remote sound system controls are located on the rear mode of the sound system. Pressing the top of the rocker surface of the steering wheel. Reach behind the wheel to switch will increase the volume, and pressing the bottom of the rocker switch will decrease the volume. access the switches.
UNDERSTANDING YOUR INSTRUMENT PANEL 361 The button located in the center of the left-hand control CD/DVD DISC MAINTENANCE will tune to the next preset station that you have pro- To keep a CD/DVD in good condition, take the following grammed in the radio preset pushbutton. precautions: CD Player 1. Handle the disc by its edge; avoid touching the Pressing the top of the switch once will go to the next surface. track on the CD. Pressing the bottom of the switch once 2.
362 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particular disc, it may be damaged (i.e., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service. RADIO OPERATION AND MOBILE PHONES Under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from your radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 363 Front Blower Control There are seven blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the OFF position. NOTE: For vehicles equipped with Remote Start, the climate controls will not function during Remote Start operation if the blower control is left in the OFF position.
364 UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control Use this control to regulate the temperature of the air inside the passenger compartment. Rotating the knob counterclockwise, from top center into the blue area of the scale, indicates cooler temperatures. Rotating the knob clockwise, into the red area, indicates warmer temperatures. Air Conditioning Operation NOTE: A/C cannot be deselected when in MAX A/C position. The LED will blink three times if the A/C button is pushed.
UNDERSTANDING YOUR INSTRUMENT PANEL 365 Panel Mode Mix Mode Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. Air is directed through the floor, defrost and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat at the windshield. This setting is good for maintaining comfort, while reducing moisture on the windshield. Bi-Level Mode Air is directed through the panel and floor outlets.
366 UNDERSTANDING YOUR INSTRUMENT PANEL • In cold or damp weather, the use of the Recirculation mode will cause windows to fog on the inside because Press this button to choose between outside air intake or of moisture buildup inside the vehicle. For maximum recirculation of the air inside the vehicle. A LED will defogging, select the outside air position. illuminate when you are in Recirculation mode.
UNDERSTANDING YOUR INSTRUMENT PANEL 367 Economy Mode Manual Climate Controls With Touch-Screen — If If ECONOMY mode is desired, press the A/C button to Equipped turn off the LED indicator and the A/C compressor. Hard-Keys Rotate the temperature control knob to the desired tem- The hard-keys located below the Uconnect® screen. perature. Also, make sure to select only Panel, Bi-Level or Floor modes.
368 UNDERSTANDING YOUR INSTRUMENT PANEL Soft-Keys Soft-keys are accessible on the Uconnect® system screen. Uconnect® 8.4 Manual Temperature Controls — Soft-keys Uconnect® 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 369 Button Descriptions (Applies To Both Hard-keys And 4. Front Defrost Button Soft-keys) Press and release to change the current airflow setting to 1. MAX A/C Button Defrost mode. The indicator illuminates when this feaPress and release to change the current setting, the ture is ON. Performing this function will cause the ATC indicator illuminates when MAX A/C is ON. Performing to switch into manual mode.
370 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window.
UNDERSTANDING YOUR INSTRUMENT PANEL 371 NOTE: BI-LEVEL mode is designed under comfort conditions to provide cooler air out of the panel outlets and The airflow distribution mode can be adjusted so air warmer air from the floor outlets. comes from the instrument panel outlets, floor outlets, demist outlets and defrost outlets. The Mode settings are Floor Mode Air comes from the floor outlets. A slight amount as follows: of air is directed through the defrost and side Panel Mode window demister outlets.
372 UNDERSTANDING YOUR INSTRUMENT PANEL Defrost Mode Air comes from the windshield and side window demist outlets. Use Defrost mode with maximum temperature settings for best windshield and side window defrosting and defogging. When the defrost mode is selected, the blower level may increase. 8. Climate Control OFF Button 10. Temperature Control Up Button (Uconnect® 8.4) Provides temperature control.
UNDERSTANDING YOUR INSTRUMENT PANEL 373 Automatic Climate Controls With Touch-Screen — If Equipped Soft-Keys Soft-keys are accessible on the Uconnect® system screen. Hard-Keys The hard-keys located below the Uconnect® screen. 4 Uconnect® 8.
374 UNDERSTANDING YOUR INSTRUMENT PANEL Button Descriptions (Applies To Both Hard-keys And 4. AUTO Operation Button Soft-keys) Automatically controls the interior cabin temperature by 1. MAX A/C Button adjusting airflow distribution and amount. Performing Press and release to change the current setting, the indicator this function will cause the ATC to switch between illuminates when MAX A/C is ON. Performing this function manual mode and automatic modes.
UNDERSTANDING YOUR INSTRUMENT PANEL 375 6. Rear Defrost Button CAUTION! (Continued) Press and release this button to turn on the rear window • Do not use scrapers, sharp instruments, or abrasive defroster and the heated outside mirrors (if equipped). An window cleaners on the interior surface of the indicator will illuminate when the rear window defroster is window. on. The rear window defroster automatically turns off after • Keep all objects a safe distance from the window. 10 minutes.
376 UNDERSTANDING YOUR INSTRUMENT PANEL 8. Passenger Temperature Control Down Button 10. Blower Control Provides the passenger with independent temperature control. Push the hard-key button for cooler temperature settings or on the touch-screen, press and slide the soft-key temperature bar towards the blue arrow soft-key for cooler temperature settings. Blower control is used to regulate the amount of air forced through the climate system. There are seven blower speeds available.
UNDERSTANDING YOUR INSTRUMENT PANEL 377 NOTE: BI-LEVEL mode is designed under comfort conditions to provide cooler air out of the panel outlets and The airflow distribution mode can be adjusted so air warmer air from the floor outlets. comes from the instrument panel outlets, floor outlets, demist outlets and defrost outlets. The Mode settings are Floor Mode Air comes from the floor outlets. A slight amount as follows: of air is directed through the defrost and side Panel Mode window demister outlets.
378 UNDERSTANDING YOUR INSTRUMENT PANEL settings or on the touch-screen, press and slide the soft-key temperature bar towards the red arrow soft-key Press and release this button to turn the Climate Control for warmer temperature settings. ON/OFF. NOTE: In Sync mode, this button will also automatically 13. Driver Temperature Control Down Button adjust the passenger temperature setting at the same time. Provides the driver with independent temperature conClimate Control Functions trol.
UNDERSTANDING YOUR INSTRUMENT PANEL 379 In MAX A/C, the blower level and mode position can be adjusted to desired user settings. Pressing other settings • If fog or mist appears on the windshield or side glass, will cause the MAX A/C operation to switch to the select Defrost mode and increase blower speed. selected setting and cause MAX A/C to exit.
380 UNDERSTANDING YOUR INSTRUMENT PANEL the windshield. On systems with Manual Climate Con- 3. When the system is set up for your comfort level, it is not necessary to change the settings. You will experitrols, the Recirculation mode is not allowed in Defrost ence the greatest efficiency by simply allowing the mode to improve window clearing operation. Recirculasystem to function automatically. tion will be disabled automatically if this mode is selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 381 Manual Operation Summer Operation The system allows for manual selection of blower speed, The engine cooling system in air-conditioned vehicles air distribution mode, A/C status and recirculation control. must be protected with a high-quality antifreeze coolant to provide proper corrosion protection and to protect The blower fan speed can be set to any fixed speed by against engine overheating. A solution of 50% OAT adjusting the blower control.
382 UNDERSTANDING YOUR INSTRUMENT PANEL • Automatic Temperature Controls (ATC) will automatiVacation Storage cally adjust the climate control settings to reduce or Any time you store your vehicle or keep it out of service eliminate window fogging on the front windshield. (i.e., vacation) for two weeks or more, run the air condiWhen this occurs, recirculation will be unavailable. tioning system at idle for about five minutes in the fresh air and high blower setting.
UNDERSTANDING YOUR INSTRUMENT PANEL 383 Control Setting Suggestions for Various Weather Conditions 4
STARTING AND OPERATING CONTENTS 䡵 STARTING PROCEDURES . . . . . . . . . . . . . . . .390 ▫ Nine–Speed Automatic Transmission . . . . . . .395 ▫ Normal Starting. . . . . . . . . . . . . . . . . . . . . . .390 ▫ Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . .397 ▫ Extreme Cold Weather 䡵 ALL WHEEL DRIVE AND FOUR-WHEEL (Below –20°F Or −29°C) . . . . . . . . . . . . . . . .391 DRIVE OPERATION . . . . . . . . . . . . . . . . . . . . .404 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . .
386 STARTING AND OPERATING 䡵 䡵 䡵 䡵 ▫ Rear Electronic Locker (E-Locker) System – If 䡵 ELECTRIC PARKING BRAKE (EPB). . . . . . Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .410 ▫ Auto Park Brake . . . . . . . . . . . . . . . . . . SELEC-TERRAIN™ . . . . . . . . . . . . . . . . . . . . .412 ▫ Safehold . . . . . . . . . . . . . . . . . . . . . . . . ▫ Description . . . . . . . . . . . . . . . . . . . . . . . . . .412 ▫ HOLD ‘n GO™ . . . . . . . . . . . . . . . . . . . ON-ROAD DRIVING TIPS . .
STARTING AND OPERATING 387 ▫ Hill Descent Control (HDC) — Four-Wheel Drive Models With Two-Speed Transfer Case Only . .438 ▫ Tire Identification Number (TIN). . . . . . . . . . .456 ▫ Electronic Stability Control (ESC) . . . . . . . . . .445 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . .463 ▫ ESC Activation/Malfunction Indicator Light And ESC OFF Indicator Light . . . . . . . . . . . .449 ▫ Tire Inflation Pressures . . . . . . . . . . . . . . . . .
388 STARTING AND OPERATING ▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . .472 ▫ Materials Added To Fuel . . . . . . . . . . . . . . . .492 ▫ Replacement Tires . . . . . . . . . . . . . . . . . . . . .473 ▫ Fuel System Cautions. . . . . . . . . . . . . . . . . . .492 䡵 TIRE CHAINS (TRACTION DEVICES) . . . . . . .475 ▫ Carbon Monoxide Warnings . . . . . . . . . . . . .493 䡵 TIRE ROTATION RECOMMENDATIONS . . . . .477 䡵 ADDING FUEL . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 389 ▫ Trailer And Tongue Weight . . . . . . . . . . . . . .504 ▫ Towing Requirements . . . . . . . . . . . . . . . . . .506 ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . .511 䡵 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) . . . . . . . . . . . .512 ▫ Towing This Vehicle Behind Another Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .512 ▫ Recreational Towing — Front-Wheel Drive (FWD) Models . . . . . . . . . . . . . . . . . . .
390 STARTING AND OPERATING STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! • When leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons.
STARTING AND OPERATING 391 Turn the ignition switch to the START position and If Engine Fails To Start release when the engine starts. If the engine fails to start WARNING! within 10 seconds, turn the ignition switch to the LOCK position, wait 10 to 15 seconds, then repeat the “Normal • Never pour fuel or other flammable liquid into the Starting” procedure. throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing Tip Start Feature serious personal injury.
392 STARTING AND OPERATING With Tip Start After Starting If the engine fails to start after you have followed the “Normal Starting” or “Extreme Cold Weather” procedures, it may be flooded. To clear any excess fuel, press the accelerator pedal all the way to the floor and hold it. Then, turn the ignition switch to the START position and release it as soon as the starter engages. The starter motor will disengage automatically in 10 seconds.
STARTING AND OPERATING 393 WARNING! CAUTION! (Continued) Remember to disconnect the engine block heater cord before driving. Damage to the 110-115 Volt AC electrical cord could cause electrocution. • Do not shift between PARK, REVERSE, NEUTRAL, or DRIVE when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly pressing the brake pedal. AUTOMATIC TRANSMISSION NOTE: You must press and hold the brake pedal while shifting out of PARK.
394 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) locked in PARK, securing the vehicle against unwanted movement. • When leaving the vehicle, always remove the key fob and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
STARTING AND OPERATING 395 Key Ignition Park Interlock Nine–Speed Automatic Transmission This vehicle is equipped with a Key Ignition Park Interlock which requires the shift lever to be placed in PARK before the ignition switch can be turned to the full OFF (key removal) position. The key fob can only be removed from the ignition when the ignition is in the full OFF position, and the transmission is locked in PARK whenever the ignition switch is in the full OFF position.
396 STARTING AND OPERATING Only shift from DRIVE to PARK or REVERSE when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when shifting between these gears. The transmission shift lever has PARK, REVERSE, NEUTRAL, DRIVE, and Electronic Range Select (ERS) shift positions. Manual downshifts can be made using the ERS shift control (refer to ⬙Electronic Range Select (ERS) Operation⬙ in this section for further information).
STARTING AND OPERATING 397 When parking on a level surface, you may shift the transmission into PARK first, and then apply the parking DO NOT race the engine when shifting from PARK or brake. NEUTRAL into another gear range. When parking on a hill, apply the parking brake before NOTE: shifting the transmission to PARK, otherwise the load on • After selecting any gear range, wait a moment to allow the transmission locking mechanism may make it diffithe selected gear to engage before accelerating.
398 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Your vehicle could move and injure you and others if it is not completely in PARK. Check by trying to move the shift lever out of PARK with the brake pedal released. Make sure the transmission is in PARK before leaving the vehicle. • It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed.
STARTING AND OPERATING 399 WARNING! (Continued) CAUTION! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever.
400 STARTING AND OPERATING • With brake pedal and lock button on the shift lever released, verify that the shift lever will not move out of PARK. REVERSE This range is for moving the vehicle backward. Shift into REVERSE only after the vehicle has come to a complete stop. WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision.
STARTING AND OPERATING 401 modify the transmission shift schedule, reduce engine torque, and/or expand the range of torque converter This range should be used for most city and highway clutch engagement. This is done to prevent transmission driving. It provides the smoothest upshifts and downdamage due to overheating. shifts, and the best fuel economy. The transmission automatically upshifts through all forward gears.
402 STARTING AND OPERATING In the event of a momentary problem, the transmission can be reset to regain all forward gears by performing the This mode alters the transmission’s automatic shift following steps: schedule for sportier driving. Upshift speeds are increased to make full use of available engine power. 1. Stop the vehicle. SPORT SPORT mode is activated using the rotary switch on the 2. Shift the transmission into PARK. center console. Refer to ⬙Selec-Terrain⬙ in this section for 3.
STARTING AND OPERATING 403 Electronic Range Select (ERS) Operation The Electronic Range Select (ERS) shift control allows the driver to limit the highest available gear. For example, if you shift the transmission into 5 (fifth gear), the transmission will not shift above fifth gear, but will shift through the lower gears normally. To exit ERS mode, simply return the shift lever to the DRIVE position. WARNING! Do not downshift for additional engine braking on a slippery surface.
404 STARTING AND OPERATING ALL WHEEL DRIVE AND FOUR-WHEEL DRIVE OPERATION Single Range All Wheel Drive (AWD) — If Equipped This feature provides on-demand All-Wheel Drive (AWD). The system is automatic with no driver inputs or additional driving skills required. Under normal driving conditions, the front wheels provide most of the traction. If the front wheels begin to lose traction, power is shifted automatically to the rear wheels.
STARTING AND OPERATING 405 Additionally, on dry pavement under heavy throttle Dual Range Four-Wheel Drive (4WD) — If Equipped input (where one may have no wheel spin), torque will be sent to the rear in a pre-emptive effort to improve vehicle launch and performance characteristics. CAUTION! All wheels must have the same size and type tires. Unequal tire sizes must not be used. Unequal tire size may cause failure of the power transfer unit.
406 STARTING AND OPERATING The Four-Wheel Drive is fully automatic in the normal Proper operation of four-wheel drive vehicles depends driving mode. The Selec-Terrain buttons provide three on tires of equal size, type, and circumference on each selectable mode positions: wheel. Any difference will adversely affect shifting and cause damage to the driveline components.. • 4WD LOW Because four-wheel drive provides improved traction, • REAR LOCK there is a tendency to exceed safe turning and stopping speeds.
STARTING AND OPERATING 407 NOTE: Refer to “Selec-Terrain® – If Equipped” for further information on the various positions and their For additional information on the appropriate use of each intended usages. 4WD system mode position, see the information below: Shifting Procedures NEUTRAL Shift Positions This range disengages the driveline from the powertrain. It is to be used for flat towing behind another vehicle. Refer to “Recreational Towing” in “Starting and Operating” for further information.
408 STARTING AND OPERATING Shifting Out Of 4WD LOW With the vehicle at speeds of 0 to 3 mph (0 to 5 km/h), the ignition switch in the ON position or the engine running, shift the transmission into NEUTRAL, and press the “4WD LOW” button once. The “4WD LOW” indicator light in the instrument cluster will flash and go out when the shift is complete.
STARTING AND OPERATING 409 • Shifting into or out of 4WD LOW is possible with the 6. Using the point of a ballpoint pen or similar object, press and hold the recessed transfer case NEUTRAL vehicle completely stopped; however, difficulty may oc(N) button (located above the selector switch) for cur due to the mating clutch teeth not being properly four seconds, until the light behind the NEUTRAL (N) aligned.
410 STARTING AND OPERATING 7. After the shift is completed and the NEUTRAL light comes on, release the NEUTRAL (N) button. 8. Start the engine. 9. Shift the transmission into REVERSE. 10. Release the brake pedal for five seconds and ensure that there is no vehicle movement. 11. Turn OFF the engine. 12. Firmly apply the parking brake. CAUTION! Damage to the transmission may occur if the transmission is shifted into PARK with the transfer case in NEUTRAL (N) and the engine running.
STARTING AND OPERATING 411 Activating the Rear E-Locker 2. The ignition switch in the ON position or the engine running. To activate the Rear E-Locker System, the following conditions must be met: 3. To disengage Rear E-Locker , press the REAR LOCK button once. 1. The 4WD system must be in 4WD LOW. NOTE: 2. The ignition switch in the ON position or the engine running. • When engaging Rear E-Locker, the indicator lights in the instrument cluster and on the REAR LOCK button 3.
412 STARTING AND OPERATING • Shifting into or out of Rear E-Locker is possible with the vehicle completely stopped; however, difficulty may occur due to the mating clutch teeth not being properly aligned. Several attempts may be required for clutch teeth alignment and shift completion to occur. The preferred method is for the vehicle to be rolling, below 15 MPH (24 km/h), while including right and left steering maneuvers to allow for the clutch teeth to align.
STARTING AND OPERATING 413 Selec-Terrain™ consists of the following positions: • Auto – Fully automatic full time four-wheel drive operation can be used on and off road. Balances traction with seamless steering feel to provide improved handling and acceleration over two-wheel drive vehicles. • Snow – Tuning set for additional stability in inclement weather. Use on and off road on loose traction surfaces such as snow.
414 STARTING AND OPERATING low-slung sports cars are designed to perform satisfactorily in off-road conditions. If at all possible, avoid sharp turns or abrupt maneuvers. As with other vehicles of this When the appropriate conditions exist, a message will type, failure to operate this vehicle correctly may result in appear in the EVIC display. Refer to “Electronic Vehicle loss of control or vehicle rollover. Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information.
STARTING AND OPERATING 415 Driving Through Water caution and maintain a steady controlled speed less than 5 mph (8 km/h) in deep water to minimize wave effects. Although your vehicle is capable of driving through water, there are a number of precautions that must be Flowing Water considered before entering the water: If the water is swift flowing and rising (as in storm run-off) avoid crossing until the water level recedes CAUTION! and/or the flow rate is reduced.
416 STARTING AND OPERATING Avoid abrupt downshifts on icy or slippery roads because engine braking may cause skidding and loss of After driving through deep water, inspect your vehicle control. fluids and lubricants (engine, transmission, Power Transfer Unit and Rear Drive Module) to assure they have not Hill Climbing been contaminated.
STARTING AND OPERATING 417 WARNING! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolling the vehicle. Always back straight down a hill in REVERSE gear carefully. Never back down a hill in NEUTRAL using only the brake.
418 STARTING AND OPERATING • Check for accumulations of plants or brush. These things could be a fire hazard. They might hide damage Off-road operation puts more stress on your vehicle than to fuel lines, brake hoses, axle pinion seals, and does most on-road driving. After going off-road, it is propeller shafts. always a good idea to check for damage. That way you can get any problems taken care of right away and have • After extended operation in mud, sand, water, or your vehicle ready when you need it.
STARTING AND OPERATING 419 • If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material. Impacted material can cause a wheel imbalance and freeing the wheels of it will correct the situation. WARNING! Continued operation with reduced assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible.
420 STARTING AND OPERATING The parking brake is primarily intended to prevent the vehicle from rolling while parked. Before leaving the • Even if the power steering assistance is no longer vehicle, make sure that the parking brake is applied. operational, it is still possible to steer the vehicle. Also, be certain to leave the transmission in PARK.
STARTING AND OPERATING 421 on the brake pedal while you apply the parking brake, you may notice a small amount of brake pedal movement. The park brake can be applied even when the ignition switch if OFF, however, it can only be released when the ignition switch is ON. Electric Parking Brake Switch To apply the parking brake manually, pull up on the switch momentarily. You may hear a slight whirring sound from the back of the vehicle while the parking brake engages.
422 STARTING AND OPERATING To release the park brake manually, the ignition switch must be ON. Put your foot on the brake pedal, then push the parking brake switch down momentarily. You may hear a slight whirring sound from the back of the car while the parking brake disengages. You may also notice a small amount of movement in the brake pedal. Once the parking brake is fully disengaged, The BRAKE warning lamp in the instrument cluster will extinguish.
STARTING AND OPERATING 423 WARNING! (Continued) • Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave a vehicle equipped with Keyless Enter-N-Go in the ACC or ON/RUN mode. A child could operate power windows, other controls, or move the vehicle. • Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision.
424 STARTING AND OPERATING To disengage the parking brake while the vehicle is in motion, release the switch. If the vehicle is brought to a complete stop using the parking brake, when the vehicle reaches approximately 3 mph, the parking brake will remain engaged.
STARTING AND OPERATING 425 Safehold can be temporarily bypassed by pressing the Electric Park Brake Switch under conditions that would normally engage Safehold. Once manually bypassed, Safehold will be enabled again once the vehicle reaches 12 mph (20 km/h) or the ignition is turned to the OFF position. HOLD ‘n GO™ Enabling Hold ‘n Go™ Hold ‘n Go™ is a driver selectable feature that can be enabled or disabled via the personalization settings in the radio or instrument cluster.
426 STARTING AND OPERATING for up to three minutes. After three minutes, Hold ‘n • When the Electric Parking Brake is engaged the “BRAKE” icon will illuminate in the instrument clusGo™ will automatically engage the Electric Parking ter, a single chime will sound, and the “HOLD” Brake. Once the Electric Parking Brake is engaged Hold message will extinguish. ‘n Go™ will release the brake pressure and return to the enabled condition.
STARTING AND OPERATING 427 Service Mode has requirements that must be met in order to be activated: • The vehicle must be at a standstill. • The park brake must be unapplied. • The transmission must be in Park or Neutral. While in service mode, the Electric Park Brake fault lamp will flash continuously while the ignition switch is ON. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment.
428 STARTING AND OPERATING All vehicle wheels and tires must be the same size and type, and tires must be properly inflated, to produce accurate signals for the computer. WARNING! Significant over or under-inflation of tires or mixing sizes of tires or wheels on the vehicle can lead to loss of braking effectiveness. The ABS conducts a low-speed self-test at about 12 mph (20 km/h). If you have your foot lightly on the brake while this test is occurring, you may feel slight pedal movement.
STARTING AND OPERATING 429 CAUTION! The ABS is subject to possible detrimental effects of electronic interference caused by improperly installed aftermarket radios or telephones. • Engines may idle at higher speeds during warm-up, which could cause rear wheels to spin and result in loss of vehicle control. Be especially careful while driving on slippery roads, in close-quarter maneuvering, parking, or stopping. • Do not drive too fast for road conditions, especially when roads are wet or slushy.
430 STARTING AND OPERATING ELECTRONIC BRAKE CONTROL SYSTEM Anti-Lock Brake System (ABS) Your vehicle is equipped with an advanced electronic brake control system commonly referred to as ESC. This system includes Anti-Lock Brake System (ABS), Traction Control System (TCS), Brake Assist System (BAS), Hill Start Assist (HSA), Electronic Roll Mitigation (ERM), and Electronic Stability Control (ESC). These systems work together to enhance both vehicle stability and control in various driving conditions.
STARTING AND OPERATING 431 Traction Control System (TCS) Brake Assist System (BAS) This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the TCS system, Brake Limited Differential (BLD), functions similar to a limited slip differential and controls the wheel spin across a driven axle.
432 STARTING AND OPERATING WARNING! The Brake Assist System (BAS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. BAS cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.
STARTING AND OPERATING 433 WARNING! Many factors, such as vehicle loading, road conditions, and driving conditions, influence the chance that wheel lift or rollover may occur. Electronic Roll Mitigation (ERM) cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles. The capabilities of an ERM-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user’s safety or the safety of others.
434 STARTING AND OPERATING WARNING! There may be situations where the Hill Start Assist (HSA) will not activate and slight rolling may occur, such as on minor hills (i.e., less than 7%), or with a loaded vehicle, or while pulling a trailer. HSA is not a substitute for active driving involvement. It is always the driver’s responsibility to be attentive to distance to other vehicles, people, and objects, and most importantly brake operation to ensure safe operation of the vehicle under all road conditions.
STARTING AND OPERATING 435 WARNING! (Continued) • Failure to follow these warnings can result in a collision or serious personal injury. Disabling And Enabling HSA This feature can be turned on or turned off.
436 STARTING AND OPERATING 7. Rotate the steering wheel back to center and then an • Active ; Hold ‘n Go™is enabled and actively holding the vehicle at standstill. additional one-half turn to the right. 8. Turn the ignition switch to the OFF position and then back to the ON position. If the sequence was completed properly, the “ESC Off Indicator Light” will blink several times to confirm HSA is disabled.
STARTING AND OPERATING 437 Once at a standstill Hold ‘n Go™ will engage by auto- Indication to the driver matically holding brake pressure when the driver re• When Hold ‘n Go™ activates, a “HOLD” message will leases the brake pedal. The brake pressure will be held illuminate in the instrument cluster. The HOLD mesfor up to three minutes. After three minutes, Hold ‘n sage is confirmation to the driver that Hold ‘n Go™ Go™ will automatically engage the Electric Parking has engaged and is holding the vehicle.
438 STARTING AND OPERATING Hill Descent Control (HDC) — Four-Wheel Drive Models With Two-Speed Transfer Case Only HDC has three states: 1. Off (feature is not enabled and will not activate) 2. Enabled (feature is enabled and ready but activation conditions are not met, or driver is actively overriding with brake or throttle application) 3.
STARTING AND OPERATING 439 Activating HDC • 4th = 2.5 mph (4 km/h) Once HDC is enabled it will activate automatically if driven down a grade of sufficient magnitude (greater than approximately 8%). The set speed for HDC is selectable by the driver, and can be adjusted by using the gear shift lever. The following summarizes the HDC set speeds: • 5th = 3.1 mph (5 km/h) • 6th = 3.7 mph (6 km/h) • 7th = 4.3 mph (7 km/h) • 8th = 5.0 mph (8 km/h) • P = No set speed. HDC may be enabled but will not • 9th = 5.
440 STARTING AND OPERATING Deactivating HDC • Driver door opens. HDC will be deactivated but remain available if any of • The vehicle is driven greater than 20 mph for greater the following conditions occur: than 70 seconds. • Driver overrides HDC set speed with throttle or brake • The vehicle is drive greater than 40 mph (HDC exits application. immediately) • Vehicle speed exceeds 20 mph but remains below Feedback to the driver: 40 mph.
STARTING AND OPERATING 441 • The cluster icon and switch lamp will flash for several Select Speed Control (SSC) — Four-Wheel Drive seconds then extinguish when HDC deactivates due to Models With Two-Speed Transfer Case and excess speed. E-Locker Only • The cluster icon and switch lamp will flash when HDC deactivates due to overheated brakes. The flashing will stop and HDC will activate again once the brakes have cooled sufficiently. SSC is intended for off road driving in 4WD Low Range only.
442 STARTING AND OPERATING The set speed for SSC is selectable by the driver, and can Enabling SSC SSC is enabled by pressing the SSC switch, but the be adjusted by using the gear shift lever. Additionally, the SSC set speed is automatically reduced when climbing a following conditions must also be met to enable SSC: grade and the level of set speed reduction depends on the • Driveline is in 4WD Low Range magnitude of grade.
STARTING AND OPERATING 443 • 9th = 5.6 mph (9 km/h) • REVERSE = .6 mph (1 km/h) • NEUTRAL = 1.2 mph (2 km/h) • PARK = SSC remains enabled but not active NOTE: These SSC default set speeds are dependant on hill grade. That is the steeper the grade of the hill the vehicle travels on the lower the values of the set speed will be for all listed gears, with the minimal value being .6 mph (1 km/h). NOTE: • SSC performance is influenced by the Terrain Select mode.
444 STARTING AND OPERATING Disabling SSC Feedback to the driver: SSC will deactivate and be disabled if any of the follow- The instrument cluster has an SSC icon and the SSC ing conditions occur: switch has an LED which offer feedback to the driver about the state SSC is in. • The driver presses the SSC switch. • The cluster icon and switch lamp will illuminate and • The driveline is shifted out of 4WD Low Range. remain on solid when SSC is enabled or activated. This • The parking brake is applied.
STARTING AND OPERATING 445 WARNING! SSC is only intended to assist the driver in controlling vehicle speed when driving in off road conditions. The driver must remain attentive to the driving conditions and is responsible for maintaining a safe vehicle speed. the intended path, ESC applies the brake of the appropriate wheel to assist in counteracting the oversteer or understeer condition. • Oversteer - when the vehicle is turning more than appropriate for the steering wheel position.
446 STARTING AND OPERATING WARNING! The Electronic Stability Control (ESC) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. ESC cannot prevent collisions, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. ESC also cannot prevent collisions resulting from loss of vehicle control due to inappropriate driver input for the conditions.
STARTING AND OPERATING 447 Partial Off – Two-Wheel Drive Vehicles And Four- “Partial Off” mode by momentarily pressing the “ESC Wheel Drive Vehicles In 2WD And 4WD High Range Off” button. Once the situation requiring “Partial Off” mode is overcome, turn ESC back on by momentarily The “Partial Off” mode is intended for driving in deep pressing the “ESC Off” button. This may be done while snow, sand, or gravel. This mode raises the threshold for the vehicle is in motion.
448 STARTING AND OPERATING Full Off – Four-Wheel Drive Vehicles In 4WD High switches to “Partial Off” mode, described above. When And 4WD Low Range the vehicle speed returns to less than 35 mph (56 km/h), the ESC system will return to “Full Off” mode. The “ESC The “Full Off” mode is intended for off-highway and Activation/Malfunction Indicator Light” is always illuoff-road use when ESC stability features could inhibit minated when ESC is off.
STARTING AND OPERATING 449 WARNING! With the ESC switched off, the enhanced vehicle stability offered by ESC is unavailable. In an emergency evasive maneuver, the ESC system will not engage to assist in maintaining stability. “Full Off” mode is only intended for off-highway or off-road use. ESC Activation/Malfunction Indicator Light And ESC OFF Indicator Light The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON position.
450 STARTING AND OPERATING NOTE: Trailer Sway Control (TSC) – If Equipped • The “ESC Activation/Malfunction Indicator Light” The TSC system uses sensors in the vehicle to recognize an and the “ESC OFF Indicator Light” come on momen- excessively swaying trailer and will take the appropriate actions to attempt to stop the sway. The system may reduce tarily each time the ignition switch is turned ON.
STARTING AND OPERATING 451 NOTE: TSC cannot stop all trailers from swaying. WARNING! If the TSC activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway. Ready Alert Braking (RAB) – If Equipped Ready Alert Braking may reduce the time required to reach full braking during emergency braking situations. It anticipates when an emergency braking situation may occur by monitoring how fast the throttle is released by the driver.
452 STARTING AND OPERATING optimal steering behavior in order to reach/maintain TIRE SAFETY INFORMATION vehicle stability. The only notification the driver receives Tire Markings that the feature is active is the torque applied to the steering wheel.
STARTING AND OPERATING 453 • LT (Light Truck) - Metric tire sizing is based on U.S. design standards. The size designation for LT-Metric • P (Passenger) - Metric tire sizing is based on U.S. tires is the same as for P-Metric tires except for the design standards. P-Metric tires have the letter “P” letters “LT” that are molded into the sidewall precedmolded into the sidewall preceding the size designaing the size designation. Example: LT235/85R16. tion. Example: P215/65R15 95H.
454 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T or S = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
STARTING AND OPERATING 455 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
456 STARTING AND OPERATING Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side. Tires the outboard side, then you will find it on the inboard side of the tire. with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
STARTING AND OPERATING 457 EXAMPLE: DOT MA L9 ABCD 0301 01 = Number representing the year in which the tire was manufactured (two digits) — 01 means the year 2001 — Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.
458 STARTING AND OPERATING Term Recommended Cold Tire Inflation Pressure Tire Placard Definition Vehicle manufacturer’s recommended cold tire inflation pressure as shown on the tire placard. A paper label permanently attached to the vehicle describing the vehicle’s loading capacity, the original equipment tire sizes and the recommended cold tire inflation pressures.
STARTING AND OPERATING 459 Tire And Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loading Tire and Loading Information Placard The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
460 STARTING AND OPERATING NOTE: Under a maximum loaded vehicle condition, Steps For Determining Correct Load Limit gross axle weight ratings (GAWRs) for the front and rear 1. Locate the statement “The combined weight of occuaxles must not be exceeded. For further information on pants and cargo should never exceed XXX lbs or GAWRs, vehicle loading, and trailer towing, refer to XXX kg” on your vehicle’s placard. “Vehicle Loading” in this section. 2.
STARTING AND OPERATING 461 5. Determine the combined weight of luggage and cargo NOTE: being loaded on the vehicle. That weight may not • The following table shows examples on how to calcusafely exceed the available cargo and luggage load late total load, cargo/luggage, and towing capacities capacity calculated in Step 4. of your vehicle with varying seating configurations 6. If your vehicle will be towing a trailer, load from your and number and size of occupants.
462 STARTING AND OPERATING
STARTING AND OPERATING 463 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
464 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. stability of the vehicle and can produce a feeling of sluggish response or over responsiveness in the steering. Unequal tire pressures from side to side may cause erratic and unpredictable steering response.
STARTING AND OPERATING 465 CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the winter.
466 STARTING AND OPERATING Tire Pressures For High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds and WARNING! within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle important. Increased tire pressure and reduced vehicle poorly.
STARTING AND OPERATING 467 Consult an authorized tire dealer for tire repairs and Summer Or Three Season Tires – If Equipped additional information. Summer tires provide traction in both wet and dry Damaged Run Flat tires, or Run Flat tires that have conditions, and are not intended to be driven in snow or experienced a loss of pressure should be replaced imme- on ice.
468 STARTING AND OPERATING Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). For speeds above 75 mph (120 km/h) refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. Run Flat tire reaches the run flat mode it has limited driving capabilities and needs to be replaced immediately.
STARTING AND OPERATING 469 Spare Tire Matching Original Equipped Tire And Wheel – If Equipped Your vehicle may be equipped with a spare tire and wheel equivalent in look and function to the original equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for your vehicle. If your vehicle has this option refer to an authorized tire dealer for the recommended tire rotation pattern.
470 STARTING AND OPERATING WARNING! (Continued) replaced. Be sure to follow the warnings, which apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control. Full Size Spare – If Equipped The full size spare is for temporary emergency use only. This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life.
STARTING AND OPERATING 471 WARNING! Limited-use spares are for emergency use only. Installation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressures listed on your Tire and Loading Information Placard located on the driver’s side B-Pillar or the rear edge of the driver’s side door.
472 STARTING AND OPERATING These indicators are molded into the bottom of the tread Tread wear indicators are in the original equipment tires grooves. They will appear as bands when the tread depth to help you in determining when your tires should be becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to replaced. replacement tires in this section for further information.
STARTING AND OPERATING 473 WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. “Tread Wear Indicators”. Refer to the Tire and Loading Information placard or the Vehicle Certification Label for the size designation of your tire.
474 STARTING AND OPERATING WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have a collision resulting in serious injury or death.
STARTING AND OPERATING 475 TIRE CHAINS (TRACTION DEVICES) 4x4 All Wheel Drive (AWD) Non-Trailhawk Models without a Two-Speed Power Takeoff Unit Use of traction devices require sufficient tire-to-body clearance. Follow these recommendations to guard against • Original equipment 225/65R17 and 225/60R18 tire damage. sizes are not chainable. • Traction device must be of proper size for the tire, as • The use of 9mm snow chains is permitted with the use recommended by the traction device manufacturer.
476 STARTING AND OPERATING CAUTION! CAUTION! • Damage to 4x2 Front Wheel Drive (FWD) Models may result if tire chains or traction devices are used with original equipment size tires. • Damage to 4x4 All Wheel Drive (AWD) Models without a Two-Speed Power Takeoff Unit may result if tire chains or traction devices are used with original equipment size tires. • Damage to 4x4 All Wheel Drive (AWD) Trailhawk Models may result if tire chains or traction devices are used with original equipment size tires.
STARTING AND OPERATING 477 CAUTION! (Continued) • Observe the traction device manufacturer’s instructions on the method of installation, operating speed, and conditions for use. Always use the suggested operating speed of the device manufacturer’s if it is less than 30 mph (48 km/h). • Do not use traction devices on a compact spare tire. Refer to the “Maintenance Schedule” for the proper maintenance intervals. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed.
478 STARTING AND OPERATING CAUTION! Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the transfer case. Tire rotation schedule should be followed to balance tire wear. three hours, or driven less than 1 mile (1.6 km) after a three hour period. The cold tire inflation pressure must not exceed the maximum inflation pressure molded into the tire sidewall.
STARTING AND OPERATING 479 cold placard pressure in order for the “Tire Pressure the “Tire Pressure Monitoring Telltale Light” will turn off Monitoring Telltale Light” to turn off. The system will only after the tires are inflated to the vehicle’s recommended automatically update and the “Tire Pressure Monitoring cold placard pressure value. Telltale Light” will turn off once the system receives the CAUTION! updated tire pressures.
480 STARTING AND OPERATING CAUTION! (Continued) • After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the Tire Pressure Monitoring Sensor. • Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
STARTING AND OPERATING 481 Base System Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitor System (TPMS) uses wireless The “Tire Pressure Monitoring Telltale Light” will technology with wheel rim mounted electronic sensors to illuminate in the instrument cluster, a “LOW TIRE monitor tire pressure levels.
482 STARTING AND OPERATING Service TPMS Warning 4. Using tire chains on the vehicle. When a system fault is detected, the “Tire Pressure Monitoring Telltale Light” will flash on and off for 75 seconds and then remain on solid. The system fault will also sound a chime. If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. The “Tire Pressure Monitoring Telltale Light” will turn off when the fault condition no longer exists.
STARTING AND OPERATING 483 4. For each subsequent ignition key cycle, a chime will sound and the “TPMS Telltale Light” will flash on and 1. The compact spare tire does not have a tire pressure off for 75 seconds and then remain on solid. monitoring sensor. Therefore, the TPMS will not monitor the pressure in the compact spare tire. 5. Once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare, 2.
484 STARTING AND OPERATING Premium System – If Equipped The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the receiver module. The matching full size spare wheel and tire assembly (if equipped) has a tire pressure monitoring sensor. The full size spare can be used in place of any of the four road tires.
STARTING AND OPERATING 485 five seconds, an ⬙Inflate to XX⬙ message and a graphic Should this occur, you should stop as soon as possible showing the pressure values of each tire with the low tire and inflate the tires with low pressure (those in a pressure values in a different color. different color in the EVIC graphic) to the vehicle’s recommended cold placard pressure value as shown in the ⬙Inflate to XX⬙ message.
486 STARTING AND OPERATING SERVICE TPMS Warning When a system fault is detected, the “Tire Pressure Monitoring Telltale Light” will flash on and off for 75 seconds and then remain on solid. The system fault will also sound a chime. In addition, the EVIC will display a ⬙SERVICE TPM SYSTEM⬙ message for three seconds and then display dashes (- -) in place of the pressure value to indicate which sensor is not being received.
STARTING AND OPERATING 487 Light” will no longer flash, and the “SERVICE TPM Vehicles With Full-Size Spare SYSTEM message will no longer display, and a pressure 1. The matching full size spare wheel and tire assembly value will display in place of the dashes. A system fault has a tire pressure monitoring sensor that can be can occur due to any of the following: monitored by the TPMS. 1. Jamming due to electronic devices or driving next to 2.
488 STARTING AND OPERATING 4. The EVIC will display a graphic showing the tire pressure 3. After driving the vehicle for up to 20 minutes above 15.5 mph (25 km/h), the “TPMS Telltale Light” will value in the same color as the other pressure values in flash on and off for 75 seconds and then remain on place of the different color low tire pressure value. The solid.
STARTING AND OPERATING 489 5. Once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically. In addition, the “TPMS Telltale Light” will turn off and the graphic in the EVIC will display a new pressure value instead of dashes (- -), as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes above 15.
490 STARTING AND OPERATING Charter, WWFC) which define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recommends the use of gasoline that 3.2L Engine Your engine is designed to meet all emissions regulations and provide satisfactory fuel economy and performance when using high quality unleaded gasoline having an octane range of 87 to 89. The manufacturer recommends the use of 89 octane premium gasoline for optimum performance.
STARTING AND OPERATING 491 CAUTION! DO NOT use gasoline containing Methanol or gasoline containing more than 10% Ethanol. Use of these blends may result in starting and driveability problems, damage critical fuel system components, cause emissions to exceed the applicable standard, and/or cause the “Malfunction Indicator Light” to illuminate. Pump labels should clearly communicate if a fuel contains greater than 10% Ethanol.
492 STARTING AND OPERATING MMT In Gasoline Materials Added To Fuel MMT (Methylcyclopentadienyl Manganese Tricarbonyl) is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT. Gasoline blended with MMT reduces spark plug life and reduces emissions system performance in some vehicles.
STARTING AND OPERATING 493 CAUTION! (Continued) • An out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your authorized dealer for service assistance. • The use of fuel additives, which are now being sold as octane enhancers, is not recommended.
494 STARTING AND OPERATING WARNING! (Continued) • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. ADDING FUEL The gas cap is located behind the fuel filler door, on the passenger side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap has been designed for use with this vehicle.
STARTING AND OPERATING 495 NOTE: • In certain cold conditions, ice may prevent the fuel door from opening. If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel door using the inside release button. Do not pry on the door. • When the fuel nozzle “clicks” or shuts off, the fuel tank is full. • Tighten the gas cap about one quarter turn until you hear one click. This is an indication that the cap is properly tightened.
496 STARTING AND OPERATING WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank is being filled. • Never add fuel when the engine is running. This is in violation of most state and federal fire regulations and may cause the MIL to turn on. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling.
STARTING AND OPERATING 497 Tighten the fuel filler cap until a “clicking” sound is heard. This is an indication that the fuel filler cap is properly tightened. Refer to “Onboard Diagnostic System” in “Maintaining Your Vehicle” for further information. VEHICLE LOADING Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo. The label also specifies maximum capacities of front and rear axle systems (GAWR).
498 STARTING AND OPERATING Each axle GAWR is determined by the components in the system with the lowest load carrying capacity (axle, springs, tires or wheels). Heavier axles or suspension components sometimes specified by purchasers for increased durability does not necessarily increase the vehicle’s GVWR.
STARTING AND OPERATING 499 front or rear axles has been exceeded but the total load is within the specified GVWR. If so, weight must be shifted from front to rear or rear to front as appropriate until the specified weight limitations are met. Store the heavier items down low and be sure that the weight is distributed equally. Stow all loose items securely before driving.
500 STARTING AND OPERATING exceed the GVWR. Refer to “Vehicle Loading/Vehicle Certification Label” in “Starting and Operating” for further information. Gross Trailer Weight (GTW) WARNING! (Continued) vehicle. If you use a standard weight- carrying hitch, you could lose control of your vehicle and cause a collision.
STARTING AND OPERATING 501 WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have a collision. Frontal Area The frontal area is the maximum height multiplied by the maximum width of the front of a trailer.
502 STARTING AND OPERATING Weight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle. These kinds of hitches are the most popular on the market today and they are commonly used to tow small and medium sized trailers. Weight-Distributing Hitch A weight-distributing system works by applying leverage through spring (load) bars.
STARTING AND OPERATING 503 WARNING! • An improperly adjusted Weight Distributing Hitch system may reduce handling, stability, braking performance, and could result in a collision. • Weight Distributing Systems may not be compatible with Surge Brake Couplers. Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.
504 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ Transmission 2.4L/Automatic 3.2L/Automatic 3.2L/Automatic with Trailer Tow Package Model Frontal Area 4x2 or 4x4 4x2 or 4x4 4x2 or 4x4 32 sq ft (2.97 sq m) 32 sq ft (2.97 sq m) 32 sq ft (2.97 sq m) Maximum GTW (Gross Trailer Wt.) 2,000 lbs (907 kg) 2,000 lbs (907 kg) 4,500 lbs (2 041 kg) Maximum Tongue Wt.
STARTING AND OPERATING 505 which will cause loss of control of the vehicle and trailer. Consider the following items when computing the Failure to load trailers heavier in front is the cause of weight on the rear axle of the vehicle: many trailer collisions. • The tongue weight of the trailer. Never exceed the maximum tongue weight stamped on • The weight of any other type of cargo or equipment your bumper or trailer hitch. put in or on your vehicle. • The weight of the driver and all passengers.
506 STARTING AND OPERATING Towing Requirements To promote proper break-in of your new vehicle drivetrain components, the following guidelines are recommended: CAUTION! • Do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven. The engine, axle or other parts could be damaged. • Then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle.
STARTING AND OPERATING 507 WARNING! (Continued) WARNING! (Continued) • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle transmission in PARK. Always, block or ⴖchockⴖ the trailer wheels.
508 STARTING AND OPERATING Towing Requirements – Tires • Do not attempt to tow a trailer while using a compact spare tire. replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s GVWR and GAWR limits. Towing Requirements – Trailer Brakes • Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 509 CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. WARNING! • Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have a collision.
510 STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations.
STARTING AND OPERATING 511 Towing Tips Electronic Speed Control – If Equipped Before setting out on a trip, practice turning, stopping, • Do not use in hilly terrain or with heavy loads. and backing the trailer in an area located away from • When using the speed control, if you experience speed heavy traffic. drops greater than 10 mph (16 km/h), disengage until Automatic Transmission you can get back to cruising speed. The “DRIVE” range can be selected when towing.
512 STARTING AND OPERATING Highway Driving Air Conditioning Reduce speed. Turn off temporarily. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
STARTING AND OPERATING 513 Recreational Towing — Front-Wheel Drive (FWD) Models DO NOT flat tow this vehicle. Damage to the drivetrain will result. CAUTION! Towing with the front wheels on the ground will cause severe transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty. Recreational towing (for two-wheel drive models) is allowed ONLY if the front wheels are OFF the ground.
514 STARTING AND OPERATING CAUTION! CAUTION! Towing this vehicle with any of its wheels on the ground can cause severe transmission and/or transfer case damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty. • DO NOT dolly tow any 4WD vehicle. Internal damage to the transmission or transfer case will occur if a dolly is used when recreational towing. • Tow only in a forward direction. Towing this vehicle backwards can cause severe damage to the transfer case.
STARTING AND OPERATING 515 CAUTION! (Continued) • Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. Shifting Into NEUTRAL (N) WARNING! You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the NEUTRAL (N) position without first fully engaging the parking brake.
516 STARTING AND OPERATING 6. Using a ballpoint pen or similar object, press and hold the 7. After the shift is completed and the NEUTRAL (N) recessed transfer case NEUTRAL (N) button (located by light comes on, release the NEUTRAL (N) button. the selector switch) for four seconds. The light behind the NEUTRAL (N) symbol will blink, indicating shift in 8. Start the engine. progress. The light will stop blinking (stay on solid) when 9. Shift the transmission into REVERSE.
STARTING AND OPERATING 517 CAUTION! Damage to the transmission may occur if the transmission is shifted into PARK with the transfer case in NEUTRAL (N) and the engine running. With the transfer case in NEUTRAL (N) ensure that the engine is OFF before shifting the transmission into PARK. 15. Attach the vehicle to the tow vehicle using a suitable tow bar. 16. Release the parking brake.
518 STARTING AND OPERATING Shifting Out Of NEUTRAL (N) Use the following procedure to prepare your vehicle for normal usage. 1. Bring the vehicle to a complete stop, leaving it connected to the tow vehicle. 2. Apply the parking brake. 3. Turn the ignition switch to the ON/RUN position, but do not start the engine. 4. Press and hold the brake pedal. 5. Shift the transmission into NEUTRAL. Neutral Switch 7. When the NEUTRAL (N) indicator light turns off, 6.
STARTING AND OPERATING 519 NOTE: When shifting out of transfer case NEUTRAL NOTE: (N), turning the engine OFF may be required to avoid • Steps 1 through 5 are requirements that must be met gear clash. prior to pressing the NEUTRAL (N) button, and must 9. Shift the transmission into PARK. continue to be met until the shift has been completed. If any of these requirements are not met prior to 10. Release the brake pedal. pressing the NEUTRAL (N) button or are no longer 11.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 HAZARD WARNING FLASHERS . . . . . . . . . . .522 䡵 JUMP-STARTING PROCEDURES. . . . . . . . . . . .535 䡵 IF YOUR ENGINE OVERHEATS . . . . . . . . . . . .522 ▫ Preparations For Jump-Start . . . . . . . . . . . . . .535 䡵 JACKING AND TIRE CHANGING . . . . . . . . . .523 ▫ Jump-Starting Procedure . . . . . . . . . . . . . . . .536 ▫ Jack Location/Spare Tire Stowage . . . . . . . . .524 䡵 FREEING A STUCK VEHICLE. . . . . . . . . . . . . .538 ▫ Preparations For Jacking . .
522 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located in the In any of the following situations, you can reduce the switch bank below the radio screen. potential for overheating your engine by taking the appropriate action. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all direc- • On the highways — slow down.
WHAT TO DO IN EMERGENCIES 523 NOTE: There are steps that you can take to slow down JACKING AND TIRE CHANGING an impending overheat condition: • If your air conditioner (A/C) is on, turn it off. The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat. • You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high.
524 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. Jack Location/Spare Tire Stowage The jack, wheel chocks and spare tire are stowed under the load floor behind the rear seat. 1. Open the liftgate . 2. Lift the access cover using the load floor handle. Load Floor Handle 3.
WHAT TO DO IN EMERGENCIES 525 6 Jack and Spare Tire Fastener 4. Remove the chocks. Jack and Tool Assembly NOTE: The jack handle attaches to the side of the jack with two attachment points. When the jack is partially 5. Remove the scissors jack and wheel bolt wrench from expanded, the tension between the two attachment the spare wheel as an assembly. Turn the jack screw to points holds the jack handle in place. the left to loosen the wheel bolt wrench, and remove the wrench from the jack assembly. 6.
526 WHAT TO DO IN EMERGENCIES WARNING! WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid being hit when operating the jack or changing the wheel. Preparations For Jacking 2.
WHAT TO DO IN EMERGENCIES 527 Jacking Instructions WARNING! 6. Chock both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, chock the left rear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked.
528 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway, be extremely careful of motor traffic.
WHAT TO DO IN EMERGENCIES 529 4. Place the jack underneath the lift area that is closest to the flat tire. Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange, centering the jack saddle between the locating notches on the sill flange.
530 WHAT TO DO IN EMERGENCIES WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the wheel bolts and tire. 7. Mount the spare tire. CAUTION! Front Jacking Location 5. Raise the vehicle just enough to remove the flat tire. Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be damaged if the spare tire is mounted incorrectly.
WHAT TO DO IN EMERGENCIES 531 NOTE: • For vehicles so equipped, do not attempt to install a center cap or wheel cover on the compact spare. • Refer to “Compact Spare Tire” and to “Limited-Use Spare” under “Tires—General Information” in “Starting and Operating” for additional warnings, cautions, and information about the spare tire, its use, and operation. 8. Install the wheel bolts with the threaded end of the wheel bolt toward the wheel. Lightly tighten the wheel bolts.
532 WHAT TO DO IN EMERGENCIES 9. Lower the vehicle to the ground by turning the jack handle counterclockwise. 10. Finish tightening the wheel bolts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the wheel bolts in a star pattern until each wheel bolt has been tightened twice. The correct tightness of each wheel bolt is 100 ft/lb. (135 N·m).
WHAT TO DO IN EMERGENCIES 533 WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately. Road Tire Installation Vehicles Equipped With Wheel Covers 1. Mount the road tire on the axle. 3. Align the valve notch in the wheel cover with the valve stem on the wheel.
534 WHAT TO DO IN EMERGENCIES 6. Finish tightening the wheel bolts. Push down on the WARNING! wrench while at the end of the handle for increased leverage. Tighten the wheel bolts in a star pattern until To avoid the risk of forcing the vehicle off the jack, each wheel bolt has been tightened twice. The correct do not tighten the lug nuts fully until the vehicle has tightness of each wheel bolt is 100 ft/lbs (135 N·m). If been lowered.
WHAT TO DO IN EMERGENCIES 535 5. After 25 miles (40 km) check the wheel bolt torque with a torque wrench to ensure that all wheel bolts are properly seated against the wheel. JUMP-STARTING PROCEDURES If your vehicle has a discharged battery it can be jumpstarted using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump-starting can be dangerous if done improperly so please follow the procedures in this section carefully.
536 WHAT TO DO IN EMERGENCIES WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
WHAT TO DO IN EMERGENCIES 537 CAUTION! WARNING! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 5.
538 WHAT TO DO IN EMERGENCIES 8. Disconnect the opposite end of the positive (+) jumper FREEING A STUCK VEHICLE cable from the positive (+) post of the booster battery. If your vehicle becomes stuck in mud, sand or snow, it 9. Disconnect the positive (+)end of the jumper cable can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the from the positive (+) post of the discharged vehicle. front wheels.
WHAT TO DO IN EMERGENCIES 539 NOTE: Press the ⬙ESC Off⬙ switch (if necessary), to place the Electronic Stability Control (ESC) system in ⬙Partial Off⬙ mode, before rocking the vehicle. Refer to “Electronic Brake Control” in “Starting And Operating” for further information. Once the vehicle has been freed, press the ⬙ESC Off⬙ switch again to restore ⬙ESC On⬙ mode.
540 WHAT TO DO IN EMERGENCIES 6. Insert a small screwdriver or similar tool down into the MOR access hole at the front of the shift lever If a malfunction occurs and the shift lever cannot be assembly, and push and hold the override release lever moved out of the PARK position, you can use the down. following procedure to temporarily move the shift lever: 7. Move the shift lever to the NEUTRAL position. 1. Firmly apply the parking brake and turn the engine OFF. 8.
WHAT TO DO IN EMERGENCIES 541 Towing Condition Flat Tow Wheel Lift or Dolly Tow Flatbed Wheels OFF the Ground NONE 2WD Models AWD Models 4WD Models If transmission is operable: • Transmission in NEUTRAL • 30 mph (48 km/h) max speed • 30 miles (48 km/h) max distance See instructions under “Recreational Towing” in “Starting And Operating” • Transmission in PARK • Transfer case in Neutral • Tow in Forward direction BEST METHOD Front Rear OK IF transmission and transfer case are operable: • Transmis
542 WHAT TO DO IN EMERGENCIES Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for the purpose, following equipment manufacturer’s instructions. Use of safety chains is mandatory. Attach a tow bar or other towing device to main structural members of the vehicle, not to bumpers or associated brackets. State and local laws applying to vehicles under tow must be observed. If you must use the accessories (wipers, defrosters, etc.
WHAT TO DO IN EMERGENCIES 543 If the transmission is not operable, or the vehicle must be towed faster than 30 mph (48 km/h) or farther than The manufacturer recommends towing your vehicle with 30 miles (48 km), tow with the rear wheels OFF the all four wheels OFF the ground using a flatbed.
544 WHAT TO DO IN EMERGENCIES All-Wheel Drive Models The manufacturer recommends towing with all wheels OFF the ground. If flatbed equipment is not available, and the transfer transmission is operable, the vehicle may be flat towed (with ALL four wheels on the ground), under the following conditions: • The transmission must be in NEUTRAL. • The towing speed must not exceed 30 mph (48 km/h). • The towing distance must not exceed 30 miles (48 km).
MAINTAINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMPARTMENT — 2.4L . . . . . . . . . .547 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . .556 䡵 ENGINE COMPARTMENT — 3.2L . . . . . . . . . .548 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . .556 䡵 ONBOARD DIAGNOSTIC SYSTEM — OBD II . .549 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . .557 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . .549 ▫ Air Conditioner Maintenance . . . . . . . . . . . . .
546 MAINTAINING YOUR VEHICLE ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . .571 ▫ Automatic Transmission . . . . . . . . . . . . . . . .573 ▫ Front/Rear Axle Fluid . . . . . . . . . . . . . . . . . .575 ▫ Sky Slider™ Top Care . . . . . . . . . . . . . . . . . .576 ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .578 ▫ Front Turn Signal And Front Side Marker Lamp . . . . . . . . . . . . . . . . . . . . . . . .593 ▫ Front Fog Lamp . . . . .
MAINTAINING YOUR VEHICLE 547 ENGINE COMPARTMENT — 2.
548 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 3.
MAINTAINING YOUR VEHICLE 549 ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
550 MAINTAINING YOUR VEHICLE Tighten the gas cap until a ⬙clicking⬙ sound is heard. This is Normally, the OBD II system will be ready. The OBD II an indication that the gas cap is properly tightened. system may not be ready if your vehicle was recently Press the odometer reset button to turn the message off. serviced, recently had a dead battery or a battery replaceIf the problem persists, the message will appear the next ment. If the OBD II system should be determined not time the vehicle is started.
MAINTAINING YOUR VEHICLE 551 4. Approximately 15 seconds later, one of two things will vehicle as you normally would in order for your OBD II happen: system to update. A recheck with the above test routine may then indicate that the system is now ready. • The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF Regardless of whether your vehicle’s OBD II system is ready the ignition or start the engine.
552 MAINTAINING YOUR VEHICLE DEALER SERVICE MAINTENANCE PROCEDURES Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these Service Manuals before attempting any procedure yourself. The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle.
MAINTAINING YOUR VEHICLE 553 CAUTION! (Continued) • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, or air conditioning. Such damage is not covered by the New Vehicle Limited Warranty. If a flush is needed because of component malfunction, use only the specified fluid for the flushing procedure.
554 MAINTAINING YOUR VEHICLE Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API Certified and meet the requirements of Chrysler Material Standard MS-6395. American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils.
MAINTAINING YOUR VEHICLE 555 Engine Oil Viscosity (SAE Grade) – 3.2L Engine Materials Added To Engine Oil SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to “Engine Compartment” in “Maintaining Your Vehicle” for further information.
556 MAINTAINING YOUR VEHICLE Engine Oil Filter Engine Air Cleaner Filter The engine oil filter should be replaced with a new filter Refer to the “Maintenance Schedule” for the proper at every engine oil change. maintenance intervals. NOTE: For best access to the oil filter, a drive on hoist NOTE: Be sure to follow the “dusty or off-road condishould be used instead of a chassis hoist. tions” maintenance interval if applicable.
MAINTAINING YOUR VEHICLE 557 Engine Air Cleaner Filter Selection WARNING! (Continued) The quality of replacement engine air cleaner filters varies considerably. Only high quality filters should be used to assure most efficient service. MOPAR® engine air cleaner filters are a high quality filter and are recommended. Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic maintenance required.
558 MAINTAINING YOUR VEHICLE CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion.
MAINTAINING YOUR VEHICLE 559 WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Warranty Information Book, located on the DVD, for further warranty information. • The air conditioning system contains refrigerant under high pressure.
560 MAINTAINING YOUR VEHICLE However, the manufacturer recommends that air conditioning service be performed by authorized dealer or other service facilities using recovery and recycling equipment.
MAINTAINING YOUR VEHICLE 561 Windshield Wiper Blades Rear Wiper Blade Removal/Installation Clean the rubber edges of the wiper blades and the 1. Lift the pivot cap on the rear wiper arm upward, this windshield periodically with a sponge or soft cloth and a will allow the rear wiper blade to be raised off of the mild nonabrasive cleaner. This will remove accumulaliftgate glass. tions of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades.
562 MAINTAINING YOUR VEHICLE NOTE: The rear wiper arm cannot be raised fully upward unless the pivot cap is raised first. 2. Lift the rear wiper arm upward to raise the wiper blade off of the liftgate glass. 3. Grab the bottom of the wiper blade and rotate it forward to unsnap the blade pivot pin from the wiper blade holder.
MAINTAINING YOUR VEHICLE 563 4. Install the wiper blade pivot pin into the wiper blade To prevent freeze-up of your windshield washer system holder at the end of the wiper arm, and firmly press in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This the wiper blade until it snaps into place. rating information can be found on most washer fluid 5. Lower the wiper blade and snap the pivot cap into containers. place.
564 MAINTAINING YOUR VEHICLE If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; have an authorized technician inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment.
MAINTAINING YOUR VEHICLE 565 CAUTION! (Continued) • Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and vehicle.
566 MAINTAINING YOUR VEHICLE • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idle or malfunctioning operating conditions. Cooling System WARNING! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool.
MAINTAINING YOUR VEHICLE 567 Cooling System – Drain, Flush, And Refill If the engine coolant (antifreeze) is dirty or contains visible sediment, clean and flush with OAT coolant (antifreeze) that meets the requirements of Chrysler Material Standard MS-12106. Refer to the “Maintenance Schedule” for the proper maintenance intervals. Selection Of Coolant Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information.
568 MAINTAINING YOUR VEHICLE CAUTION! (Continued) • This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended. Adding Coolant Please review these recommendations for using Organic Additive Technology (OAT) engine coolant (antifreeze) that meets the requirements of Chrysler Material Standard MS-12106.
MAINTAINING YOUR VEHICLE 569 Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated. NOTE: Mixing engine coolant (antifreeze) types is not recommended and can result in cooling system damage. Drain, flush, and refill as soon as possible to avoid damage if coolant types are mixed in an emergency.
570 MAINTAINING YOUR VEHICLE Disposal Of Used Engine Coolant The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. Used ethylene glycol-based engine coolant (antifreeze) is a regulated substance requiring proper disposal.
MAINTAINING YOUR VEHICLE 571 If an examination of your engine compartment shows no • Make sure that the coolant expansion bottle overflow evidence of radiator or hose leaks, the vehicle may be hoses are not kinked or obstructed. safely driven. The vapor will soon dissipate. • Keep the front of the radiator clean. If your vehicle is • Do not overfill the coolant expansion bottle. equipped with air conditioning, keep the front of the condenser clean.
572 MAINTAINING YOUR VEHICLE WARNING! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency. Brake Master Cylinder The fluid in the master cylinder should be checked when performing under hood services or immediately if the “Brake Warning Light” is illuminated.
MAINTAINING YOUR VEHICLE 573 WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a collision.
574 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for fluid specifications. Do not use chemical flushes in your transmission as the chemicals can damage your transmission components. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE 575 CAUTION! • If a transmission fluid leak occurs, visit your authorized dealer immediately. Severe transmission damage may occur. Your authorized dealer has the proper tools to adjust the fluid level accurately. Fluid And Filter Changes Front/Rear Axle Fluid For normal service, periodic fluid level checks are not required. When the vehicle is serviced for other reasons the exterior surfaces of the axle assembly should be inspected.
576 MAINTAINING YOUR VEHICLE top and tracks. Periodically wipe dust and dirt from the top and inside of the tracks by hand with an alcohol Use only manufacturer’s recommended lubricant. Refer dampened cloth. to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Washing Lubricant Selection Hand washing or an automatic car wash with a soft cloth Under normal operating conditions, the lubricant in- system is preferred.
MAINTAINING YOUR VEHICLE 577 If Hand Washing: • Wash in partial shade instead of direct sun. • Wet the entire vehicle before washing the top. • Wash the top with a soft, natural bristle scrub brush, and a mild soap solution such as liquid dish washing soap. Do not use detergent. • Scrub in all directions, covering an area of about two square feet at a time. Avoid heavy scrubbing. • Multiple cleanings may be necessary to remove stubborn stains.
578 MAINTAINING YOUR VEHICLE Rinse the area with warm water. If the stain is still apparent, repeat the cleaning procedure. When the stain is no longer showing, rinse the complete top with warm water. Let the top dry before opening it. Protection Weather Strip Care Lubricate the weather strips periodically with MOPAR® Weather Strip Lubricant or equivalent, to keep them soft and pliable.
MAINTAINING YOUR VEHICLE 579 The following maintenance recommendations will enable Washing you to obtain maximum benefit from the corrosion • Wash your vehicle regularly. Always wash your veresistance built into your vehicle. hicle in the shade using MOPAR® Car Wash, or a mild car wash soap, and rinse the panels completely with What Causes Corrosion? clear water.
580 MAINTAINING YOUR VEHICLE CAUTION! • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals. Special Care • If your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible.
MAINTAINING YOUR VEHICLE 581 Wheel And Wheel Trim Care Stain Repel Fabric Cleaning Procedure – If Equipped • All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly Stain Repel seats may be cleaned in the following manner: with a mild soap and water to prevent corrosion. • Remove as much of the stain as possible by blotting with a clean, dry towel. • To remove heavy soil and/or excessive brake dust, use MOPAR® Wheel Cleaner.
582 MAINTAINING YOUR VEHICLE Interior Care Instrument Panel Cover The instrument panel cover has a low glare surface, which minimizes reflections in the windshield. Do not use protectants or other products, which may cause undesirable reflections. Use soap and warm water to restore the low glare surface. Cleaning Interior Trim Clean interior trim with a damp cloth and MOPAR® Total Clean or equivalent, and if necessary, follow with MOPAR® Spot & Stain Remover or equivalent.
MAINTAINING YOUR VEHICLE 583 caution when cleaning the inside rear window equipped with electric defrosters or the right rear quarter window Your vehicle is equipped with plastic headlights and fog equipped with the radio antenna. Do not use scrapers or lights (if equipped) that are lighter and less susceptible to other sharp instrument that may scratch the elements. stone breakage than glass headlights.
584 MAINTAINING YOUR VEHICLE Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the car to wash them. Dry with a soft cloth. Replace the belts if they appear frayed or worn or if the buckles do not work properly.
MAINTAINING YOUR VEHICLE 585 Cavity F7 Cartridge Fuse — 225 Amp 150 Amp 70 Amp Tan — F8 — F10 — F2 F3 F4 F5 MiniFuse Description — — Battery Feed (B+) Alternator — Cabin Heater - Diesel Engine Only Power Steering — 15 Amp Blue 25 Amp Natural 20 Amp Yellow Powertrain Control Module - Diesel Engine Only Engine Control Module (ECM)/Fuel Injectors Power Takeoff Unit (PTU) Cavity F12 Cartridge Fuse — F13 — F14 — F16 — MiniFuse Description 20 Amp Yellow 10 Amp Red 10 Amp Red Brake Vac
586 MAINTAINING YOUR VEHICLE Cavity F20 Cartridge Fuse 40 Amp Green — F22 — F23 70 Amp Tan 30 Amp Green — F19 F26 F28 MiniFuse — 10 Amp Red 5 Amp Tan — — 15 Amp Blue Description Starter Cavity F30 Cartridge Fuse — MiniFuse Description 10 Amp Red Engine Control Module (ECM)/Electric Power Steering/Coil-Relay K21 (Fuel Pump) Driver Door Module (DDM) - If Equipped Body Controller Module (BCM) - Feed 3 OC/DC Converter A/C Clutch Radiator Fan Enable F33 Body Controller Module (BCM) - Feed 1
MAINTAINING YOUR VEHICLE 587 Cavity F40 F41 F42 F43 Cartridge Fuse 20 Amp Blue 60 Amp Yellow 30 Amp Green — MiniFuse Description Cavity — Trailer Tow Park Light - If Equipped Body Controller Module (BCM) - Feed 2 Electric Park Brake (EPB) - Left Trailer Tow Left Stop/Turn Light - If Equipped Trailer Tow/7-Way Connector - If Equipped Passenger Door Module (PDM) - If Equipped F46 — — 20 Amp Yellow F44 30 Amp Green — F45 30 Amp Green — F47 F49 Cartridge Fuse 25 Amp Natural MiniFuse Descript
588 MAINTAINING YOUR VEHICLE Cavity F55 Cartridge Fuse — F56 — F57 — F58 — F60 — MiniFuse Description Cavity 10 Amp Red 15 Amp Blue Rear Camera/ Blindspot Monitoring Ignition Node Module (IGNM)/KIN/RF Hub/Electric Steering Column Lock (ESL) Fuel Pump Motor F62 Cartridge Fuse — F63 — F64 — Voltage Stabilization Module (VSM) Power Outlet-Center Console F65 — 20 Amp Yellow 10 Amp Red 20 Amp Yellow MiniFuse Description 10 Amp Red Power Mirror Switch/ Driver Window Switch/Heated Mir
MAINTAINING YOUR VEHICLE 589 Cavity F66 Cartridge Fuse — MiniFuse Description Cavity 10 Amp Red In Car Temperature Sensor/Humidity Sensor/Driver Assist System Module (DASM)/Park Assist (PAM) Transfer Case Switch (TSBM)/Active Grill Shutter (AGS) Windshield De-Icer If Equipped Trailer Tow Right Stop/Turn Light - If Equipped F73 F69 — 10 Amp Red F71 — 20 Amp Yellow 20 Amp Yellow F72 — F75 Cartridge Fuse 30 Amp Green 20 Amp Blue — F76 — F77 — F78 — F74 MiniFuse Description — Rear
590 MAINTAINING YOUR VEHICLE Cavity F79 Cartridge Fuse — F80 — F83 30 Amp Green 20 Amp Blue F84 MiniFuse Description Cavity 10 Amp Red Integrated Center Stack (ICS)/HVAC/ Aux Switch Bank Module (ASBM)/ Instrument Panel Cluster (IPC) Radio/CD F88 Cartridge Fuse — F89 — F92 — F93 40 Amp Green 30 Amp Green — 20 Amp Yellow — — Headlamp Washer Pump - If Equipped Trailer Tow Back-up Lamps - Gasoline Engine Only/Brake System Module (BSM) Diesel Engine Only F94 F95 MiniFuse Description 15
MAINTAINING YOUR VEHICLE 591 Cavity F96 Cartridge Fuse — F97 — F98 25 Amp Natural 30 Amp Green F99 MiniFuse Description 10 Amp Red 10 Amp Red — Occupant Restraint Controller (ORC) Occupant Restraint Controller (ORC) HIFI Amplifier - If Equipped Trailer Tow Module If Equipped — REPLACEMENT BULBS Interior Bulbs Cargo Lamp Overhead Console Lamp Reading Lamp Bulb Number TL212–2 PLW214–2A WL212–2 Exterior Bulbs Low Beam/High Beam (Bi-Halogen) Headlamps Low Beam/High Beam (Bi-Xenon) Headlamps Fron
592 MAINTAINING YOUR VEHICLE Front Turn Signal Lamps Front Side Marker Lamps Front Fog Lamps Rear Tail/Stop/Turn Signal Lamps Center High Mounted Stop Lamp (CHMSL) Back-Up Lamps License Plate Lamp Bulb Number 7440NA 194 H11 LED ( Serviced at an Authorized Dealer) LED (Serviced at an Authorized Dealer) W16W W5W BULB REPLACEMENT NOTE: Lens fogging can occur under certain atmospheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor.
MAINTAINING YOUR VEHICLE 593 Bi-Halogen Headlamps 1. Unlock upper access door in wheel liner. 6. Install the bulb and connector assembly into the headlamp housing and rotate clockwise to lock it in place. 2. Reach behind the headlamp housing to access the 7. Install the bulb cap in the headlamp housing and headlamp bulb cap. rotate clockwise to lock it in place. 3. Firmly grasp the cap and rotate it counterclockwise to 8. Lock upper door in wheel liner. unlock it.
594 MAINTAINING YOUR VEHICLE 4. Install the bulb and socket assembly into the housing, and rotate the socket clockwise to lock it in place. 5. Re-install air cleaner filter housing, if removed. Front Fog Lamp 1. Unlock lower access door in wheel liner. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 2. Reach behind the fog lamp housing to access the bulb. 5.
MAINTAINING YOUR VEHICLE 595 Bodyside Mounted Back-up Lamp Liftgate Mounted Back-up Lamp 1. Open the liftgate. 1. Open the liftgate. 2. Remove the screws that fasten the tail lamp housing to 2. Use a fiber stick or flat blade screw driver to pry the the vehicle. lower trim from the liftgate. 3. Grasp the tail lamp and pull firmly rearward to 3. Once the trim is loose, pull it back exposing the trim disengage the lamp from the vehicle. panel. 4. Disconnect the electrical connector. 4.
596 MAINTAINING YOUR VEHICLE 8. Replace the bulb, reinstall the socket. License Plate Lamp 9. Connect the electrical connector. 1. Using a small screwdriver, press inward the locking tab on the side of the lamp assembly and pull down on the lamp assembly for removal. 10. Reinstall the trim panel and the lower trim. 11. Close the liftgate. 2. Pull bulb from socket, replace, and reinstall the lamp assembly into place ensuring the locking tab is secure. FLUID CAPACITIES Fuel (Approximate) 2.4L and 3.
MAINTAINING YOUR VEHICLE 597 U.S. 3.2 Liter Engine (MOPAR® Antifreeze/Engine Coolant 10 Quarts 10 Year/150,000 Mile Formula) * Includes heater and coolant recovery bottle filled to MAX level. Metric 9.5 Liters FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil – 2.4L Engine Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® Antifreeze/Coolant 10 Year/ 150,000 Mile Formula OAT (Organic Additive Technology).
598 MAINTAINING YOUR VEHICLE Component Engine Oil – 3.2L Engine Engine Oil Filter Spark Plugs – 2.4L Engine Spark Plugs – 3.2L Engine Fuel Selection – 2.4L Engine Fuel Selection – 3.2L Engine Fluid, Lubricant, or Genuine Part We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to your engine oil filler cap for correct SAE grade. We recommend you use a MOPAR® Engine Oil Filter. We recommend you use MOPAR® Spark Plugs (Gap 0.
MAINTAINING YOUR VEHICLE 599 Chassis Component Automatic Transmission Brake Master Cylinder Fluid, Lubricant, or Genuine Part We recommend you only use MOPAR® ZF 8&9 Speed ATF™ Automatic Transmission Fluid, Shell L12108 Transmission Fluid, or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. We recommend you use MOPAR® DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable.
M A I N T E N A ▫ Maintenance Chart. . . . . . . . . . . . . . . . . . . . .604 N C E MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULE . . . . . . . . . . . . .
M A I N T E N A N C E S C H E D U L E S 8 602 MAINTENANCE SCHEDULES On Electronic Vehicle Information Center (EVIC) equipped vehicles, “Oil Change Required” will be disYour vehicle is equipped with an automatic oil change played in the EVIC and a single chime will sound, indicator system. The oil change indicator system will indicating that an oil change is necessary. remind you that it is time to take your vehicle in for scheduled maintenance.
MAINTENANCE SCHEDULES 603 M Once A Month Or Before A Long Trip: • Check engine oil level • Check windshield washer fluid level • Check the tire inflation pressures and look for unusual wear or damage • Check the fluid levels of the coolant reservoir and brake master cylinder, fill as needed • Check function of all interior and exterior lights Required Maintenance Intervals. Refer to the maintenance schedules on the following page for the required maintenance intervals.
8 Additional Inspections Inspect the CV joints. Inspect front suspension, boot seals. tie rod ends, and replace if necessary. Inspect the brake linings, parking brake function. Additional Maintenance Replace engine air cleaner filter. Replace air conditioning/cabin air filter.
Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 110,000 120,000 130,000 140,000 150,000 Or Years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Or Kilometers: 32,000 48,000 64,000 80,000 96,000 112,000 128,000 144,000 160,000 176,000 192,000 208,000 224,000 240,000 MAINTENANCE SCHEDULES 605 M Replace spark plugs – 2.4L Engine ** Replace spark plugs – 3.
M 606 MAINTENANCE SCHEDULES A I WARNING! N T E • You can be badly injured working on or around a motor vehicle. Do only service work for which you N A have the knowledge and the right equipment. If N you have any doubt about your ability to perform a C service job, take your vehicle to a competent meE S C H E D U L E S 8 chanic. • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE . . . . . . . . . . . . . . . . . . .609 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . .611 ▫ Prepare For The Appointment. . . . . . . . . . . . .609 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . .612 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . .609 䡵 WARRANTY INFORMATION . . . . . . . . . . . . .613 ▫ Be Reasonable With Requests . .
608 IF YOU NEED CONSUMER ASSISTANCE 䡵 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES . . . . . . . . .615 ▫ Treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .616 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . .616 ▫ Temperature Grades. . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 609 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment Be Reasonable With Requests If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority. At many authorized dealer, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an appointment.
610 IF YOU NEED CONSUMER ASSISTANCE Warranty service must be done by an authorized dealer. We strongly recommend that you take the vehicle to an authorized dealer. They know your vehicle the best, and are most concerned that you get prompt and high quality service. The manufacturer’s authorized dealer have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner.
IF YOU NEED CONSUMER ASSISTANCE 611 Chrysler Canada Inc. Customer Center P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone: (800) 465–2001 English / (800) 387–9983 French In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F.
612 IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for a vehicle to help protect you from the high cost of unexpected repairs after the manufacturer’s New Vehicle Limited Warranty expires. The manufacturer stands behind only the manufacturer’s service contracts. If you purchased a manufacturer’s service contract, you will receive Plan Provisions and an Owner Identification Card in the mail within three weeks of the vehicle delivery date.
IF YOU NEED CONSUMER ASSISTANCE 613 WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm.
614 IF YOU NEED CONSUMER ASSISTANCE campaign. However, NHTSA cannot become involved in PUBLICATION ORDER FORMS individual problems between you, your authorized To order the following manuals, you may use either the dealer, and the manufacturer. website or the phone numbers listed below. Visa, MasTo contact NHTSA, you may either call the Auto Safety tercard, American Express, and Discover orders are acHotline toll free at 1–888–327–4236 (TTY: 1–800–424– cepted.
IF YOU NEED CONSUMER ASSISTANCE 615 Diagnostic Procedure Manuals Call toll free at: Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features.
616 IF YOU NEED CONSUMER ASSISTANCE Treadwear Traction Grades The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
IF YOU NEED CONSUMER ASSISTANCE 617 Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
620 INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . . .427 Adaptive Cruise Control (ACC) (Cruise Control) . . .172 Adding Engine Coolant (Antifreeze) . . . . . . . . . . . .568 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .492 Airbag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Airbag Deployment . . . . . . . . . . . . . . . . . . . . . . . .86 Airbag Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 Airbag Maintenance . . . . .
INDEX 621 Automatic Transaxle . . . . . . . . . . . . . . . . . . . . . . .393 Automatic Transmission . . . . . . . . . . . . . . . . . . . .395 Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . . . .575 Fluid and Filter Changes . . . . . . . . . . . . . . . . . .575 Fluid Change . . . . . . . . . . . . . . . . . . . . . . . . . .575 Fluid Level Check . . . . . . . . . . . . . . . . . . . . . . .573 Fluid Type . . . . . . . . . . . . . . . . . . . . . . . . . . . .573 Special Additives . . . . . .
622 INDEX Radiator (Coolant Pressure) . . . . . . . . . . . . . . . .569 Carbon Monoxide Warning . . . . . . . . . . . . . . . . . .115 Cargo Area Cover . . . . . . . . . . . . . . . . . . . . . . . . .287 Cargo Area Features . . . . . . . . . . . . . . . . . . . . . . .285 Cargo Compartment . . . . . . . . . . . . . . . . . . . . . . .285 Cargo Load Floor . . . . . . . . . . . . . . . . . . . . . . . . .285 Cargo Tie-Downs . . . . . . . . . . . . . . . . . . . . . . . . .286 Car Washes . . . . . . . . . .
INDEX 623 Points to Remember . . . . . . . . . Pressure Cap . . . . . . . . . . . . . . Radiator Cap . . . . . . . . . . . . . . Selection of Coolant (Antifreeze) . Corrosion Protection . . . . . . . . . . . Cruise Control (Speed Control). . . . Cupholders . . . . . . . . . . . . . . . . . Customer Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
624 INDEX Emergency, In Case of Hazard Warning Flasher . . . . . . . . . . . . . . . . . .522 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .523 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . .535 Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . .522 Emission Control System Maintenance . . . . . . . . . .550 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .547 Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 625 Fabric Care. . . . . . . . . . . . . . . . . . . Filters Air Cleaner . . . . . . . . . . . . . . . . Air Conditioning . . . . . . . . . . . . Engine Oil . . . . . . . . . . . . . . . . . Engine Oil Disposal . . . . . . . . . . Flashers Hazard Warning . . . . . . . . . . . . . Turn Signal . . . . . . . . . . . . . . . . . Flash-To-Pass . . . . . . . . . . . . . . . . . Flooded Engine Starting . . . . . . . . . Floor Console . . . . . . . . . . . . . . . . . Fluid, Brake . . . . . . . . . . . . . .
626 INDEX Specifications . . . . . . . . . . . . . . . . . . . . . . . . . .597 Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . . .596 Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .584 Garage Door Opener (HomeLink®) . . . . . . . . . . . .257 Gas Cap (Fuel Filler Cap) . . . . . . . . . . . . . . . . . . .494 Gasoline, Clean Air . . . . . . . . . . . . . . . . . . . . . . . .490 Gasoline (Fuel) . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 627 Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . . . .90 Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . . .126 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . . .296 Instrument Panel and Controls . . . . . . . . . . . . . . . .295 Instrument Panel Cover . . . . . . . . . . . . . . . . . . . . .582 Instrument Panel Lens Cleaning . . . . . . . . . . . . . . .583 Interior Appearance Care . . . . . . . . . . . . . . . . . . . .582 Interior Lights . . . . .
628 INDEX .22 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118 Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 .19 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .299 .18 Automatic Headlights . . . . . . . . . . . . . . . . . . . .152 .12 Back-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .595 .17 Battery Saver . . . . . . . . . . . . . . . . . . . . . . . . . .159 Brake Assist Warning . . . . . . . . . . . . . . . . . .
INDEX 629 High Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . .156 High Beam Indicator . . . . . . . . . . . . . . . . . . . . .298 High Beam/Low Beam Select . . . . . . . . . . . . . . .156 Hill Descent Control Indicator . . . . . . . . . . . . . .438 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . .22 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . .151 Intensity Control . . . . . . . . . . . . . . . . . . . . . . . .157 Interior . . . . . . . . . . . . . . . . .
630 INDEX Maintenance Free Battery. . . . . . . . . . . . . . . . . . . .557 Maintenance Procedures . . . . . . . . . . . . . . . . . . . .552 Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . .602 Malfunction Indicator Light (Check Engine). . . . . . .304 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . .614 Marker Lights, Side . . . . . . . . . . . . . . . . . . . . . . . .593 Master Cylinder (Brakes) . . . . . . . . . . . . . . . . . . . .572 Memory Feature (Memory Seat) .
INDEX 631 Passing Light . . . . . . . . . . . . . . . . . . . . . . . . . . . .156 Pets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 Pets, Transporting . . . . . . . . . . . . . . . . . . . . . . . . .113 Placard, Tire and Loading Information . . . . . . . . . .459 Power Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .278 Lift Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
632 INDEX Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . . .466 Radiator Cap (Coolant Pressure Cap) . . . . . . . . . . .569 Radio Operation . . . . . . . . . . . . . . . . . . . . . . . . . .362 Radio Remote Controls . . . . . . . . . . . . . . . . . . . . .360 Rain Sensitive Wiper System . . . . . . . . . . . . . . . . .163 Rear Axle (Differential) . . . . . . . . . . . . . . . . . . . . .575 Rear Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . .255 Rear Park Sense System .
INDEX 633 Roof Type Carrier . . . . . . . . . . . . . . . . . . . . . . . . .291 Rotation, Tires . . . . . . . . . . . . . . . . . . . . . . . . . . .477 Safety Checks Inside Vehicle. . . . . . . . . . . . . . . . . .116 Safety Checks Outside Vehicle . . . . . . . . . . . . . . . .118 Safety Defects, Reporting . . . . . . . . . . . . . . . . . . . .613 Safety, Exhaust Gas. . . . . . . . . . . . . . . . . . . . . . . . .51 Safety Information, Tire . . . . . . . . . . . . . . . . . . . . .452 Safety Tips . .
634 INDEX Service Assistance . . . . . . . . . . . . . . . . . . . . . . . . .609 Service Contract . . . . . . . . . . . . . . . . . . . . . . . . . .612 Service Manuals . . . . . . . . . . . . . . . . . . . . . . . . . .614 Shifting Automatic Transmission . . . . . . . . . . . . . . . . . .395 Shift Lever Override . . . . . . . . . . . . . . . . . . . . . . .540 Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 Side Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 635 Sun Roof (Sky Slider Power) . . . . . . . . . . . . . . . . .270 Tires . . . . . . . . . . . . . . . . . . . . . . Aging (Life of Tires) . . . . . . . . . Sun Visor Extension . . . . . . . . . . . . . . . . . . . . . . .131 Air Pressure . . . . . . . . . . . . . . . Supplemental Restraint System - Airbag . . . . . . . . . .65 Chains . . . . . . . . . . . . . . . . . . . Sway Control, Trailer. . . . . . . . . . . . . . . . . . . . . . .501 Changing . . . . . . . . . . . . . . . . .
636 INDEX Sizes . . . . . . . . . . . . . . . . Snow Tires . . . . . . . . . . . . Spinning . . . . . . . . . . . . . Trailer Towing . . . . . . . . . Tread Wear Indicators . . . . Tire Safety Information . . . . . Tongue Weight/Trailer Weight To Open Hood . . . . . . . . . . . Towing . . . . . . . . . . . . . . . . Disabled Vehicle . . . . . . . . Guide . . . . . . . . . . . . . . . Recreational . . . . . . . . . . . Weight . . . . . . . . . . . . . . . Traction Control . . . . . . . . . .
INDEX 637 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . . .472 Warnings and Cautions. . . . . . . . . . . . . . . . . . . . . . .7 Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155 Warranty Information . . . . . . . . . . . . . . . . . . . . . .613 Washers, Windshield . . . . . . . . . . . . . . . . . . . . . . .159 Uniform Tire Quality Grades . . . . . . . . . . . . . . . . .615 Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
2014 Cherokee 2014 OWNER’S MANUAL Chrysler Group LLC 14KL74-126-AA First Edition Printed in U.S.A.
