RAM TRUCKS 1500/2500/3500 USER GUIDE 2012 Download a FREE electronic copy of the Owner’s Manual or Warranty Booklet by visiting the Ownership tab at: www.ramtrucks.com (U.S.) or www.ramtruck.ca (Canada). 12D241-926-AA Ram Trucks 1500/2500/3500 First Edition User Guide 881505_12_RAM_Truck_1500-2500-3500_User_Guide_050611.
If you are the first registered retail owner of your vehicle, you may obtain a complimentary printed copy of the Owner’s Manual, Navigation/Media Center Manuals or Warranty Booklet by calling 1-866-726-4636 (U.S.) or 1-800-387-1143 (Canada) or by contacting your dealer. RAMTRUCKS.COM The driver’s primary responsibility is the safe operation of the vehicle. Driving while distracted can result in loss of vehicle control, resulting in a collision and personal injury.
TABLE OF CONTENTS INTRODUCTION/WELCOME Power Outlets . . . . . . . . . . . . . . 70 Welcome From Chrysler Group LLC . . . 2 OFF-ROAD CAPABILITIES CONTROLS AT A GLANCE Four-Wheel Drive Operation . . . . . . 72 Driver Cockpit . . . . . . . . . . . . . . . 4 Instrument Cluster . . . . . . . . . . . . 6 UTILITY GETTING STARTED Key Fob . . . . . . . . . . . . . . Remote Start . . . . . . . . . . . . Theft Alarm . . . . . . . . . . . . Seat Belt . . . . . . . . . . . . . .
INTRODUCTION/WELCOME WELCOME FROM CHRYSLER GROUP LLC Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. Your new Chrysler Group LLC vehicle has characteristics to enhance the driver's control under some driving conditions. These are to assist the driver and are never a substitute for attentive driving. They can never take the driver's place.
INTRODUCTION/WELCOME WARNING! • Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury. • Always make sure that objects cannot fall into the driver foot well while the vehicle is moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control.
DRIVER COCKPIT CONTROLS AT A GLANCE 4
− Electronic Stability Control pg. 91 − Hazard Switch D. Headlight Switch pg. 20 E. Turn Signal/Wiper/Washer/High Beams Lever (behind steering wheel) pg. 19 I. Audio System (touch-screen-radio shown) pg. 30 H. Transmission Gear Selector G. Instrument Cluster pg. 6 F. Electronic Vehicle Information Center (EVIC) Display pg. 65 − Tow/Haul pg. 80 L. Power Inverter Outlet pg. 69 K. Climate Controls pg. 24 − Tire Pressure Monitoring System (TPMS) Light Load pg. 26 − Park Assist pg.
CONTROLS AT A GLANCE INSTRUMENT CLUSTER Warning Lights BRAKE - Low Fuel Warning Light - Charging System Light** - Oil Pressure Warning Light** - Anti-Lock Brake (ABS) Light** - Air Bag Warning Light** - Electronic Throttle Control (ETC) Light - Tire Pressure Monitoring System (TPMS) Light - Engine Temperature Warning Light - Transmission Temperature Warning Light - Seat Belt Reminder Light - Brake Warning Light** - Malfunction Indicator Light (MIL)** - Electronic Stability Control (ESC) Activation/Malfun
CONTROLS AT A GLANCE Indicators - Turn Signal Indicators - High Beam Indicator - Front Fog Light Indicator - Vehicle Security Indicator* - TOW/HAUL Indicator - Four-Wheel Drive LOW Mode Indicator - Four-Wheel Drive and 4LOCK Mode Indicator - 4WD Auto Indicator - Electronic Stability Control (ESC) Off Indicator - Cargo Lamp On Indicator - Exhaust Brake Indicator (Diesel Only) - Door Ajar Indicator - Electronic Speed Control Set Indicator - Loose Gas Cap Indicator Odometer Messages ECO - Fuel Saver Indicat
GETTING STARTED KEY FOB Locking And Unlocking The Doors • Press the LOCK button once to lock all the doors. Press the UNLOCK button once to unlock the driver’s door only and twice within five seconds to unlock all the doors. • All doors can be programmed to unlock on the first press of the UNLOCK button. Refer to Programmable Features in this guide. Panic Alarm • Press the PANIC button once to turn the panic alarm on.
GETTING STARTED WARNING! • Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be severely injured or killed. Children should be warned not to touch the parking brake, brake pedal, or the shift lever. Do not leave the Key Fob inside the vehicle or in the ignition. A child could start the vehicle, operate power windows, other controls, or move the vehicle. • Do not leave children or animals inside parked vehicles in hot weather.
GETTING STARTED SEAT BELT • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Position the lap belt across your thighs, below your abdomen. To remove slack in the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. • Position the shoulder belt on your chest so that it is comfortable and not resting on your neck.
GETTING STARTED • This vehicle may be equipped with Supplemental Seat-Mounted Side Air Bags to provide enhanced protection to help protect an occupant during a side impact. • If the Air Bag Warning Light is not on during starting, stays on, or turns on while driving, have the vehicle serviced by an authorized service center immediately. • Refer to the Owner's Manual on the DVD for further details regarding the Supplemental Restraint System (SRS).
GETTING STARTED • LATCH equipped seating positions have both lower anchor bars, located at the back of the seat cushion, and tether strap anchorages, located behind the seat back. Installing The Lower Attachments: • The vehicle lower anchorages are round bars located at the rear of the seat cushion where it meets the seatback.
GETTING STARTED • Pass each tether strap hook under the head restraint and through the loop of webbing behind the child seat. • Route each tether strap to the anchor behind the center seat, and attach the hooks to the anchor loop. • Place a child restraint on the center rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat and to the anchor directly behind the right seat.
GETTING STARTED WARNING! • In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be severely injured or killed. Any child riding in your vehicle should be in a proper restraint for the child's size.
GETTING STARTED Memory Seats • The memory seat feature allows you to save the driver's seat position (excluding lumbar position), driver's outside mirror position, adjustable brake and accelerator pedals, Automatic Temperature Control (ATC) temperature setting and radio station preset settings. The driver's memory buttons are located on the outboard side of the driver's seat cushion. • Adjust all memory profile settings, press the SET button, then press 1 or 2 within five seconds.
GETTING STARTED WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted, and you could be severely injured or killed. Only adjust a seat while the vehicle is parked. • Actuating the recliner handle will allow the seatback to swing (dump) forward on manual recliner seats. Do not stand or lean in front of the seat while actuating the handle.
GETTING STARTED Rear Heated Seats • Second row heated seat switches are located on the rear of the center console. • Press the switch once to select High-level heating. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off. • If the High-level setting is selected, the system will automatically switch to Low-level after approximately 60 minutes. The Low-level setting will turn Off automatically after approximately 45 minutes.
GETTING STARTED TILT STEERING COLUMN / ADJUSTABLE PEDALS Tilt Steering Column • The tilt lever is located on the steering column, below the turn signal lever. • Pull forward on the lever and move the steering wheel up or down as desired. • Release the lever to lock the steering wheel into position.
OPERATING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS • A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. • Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. • While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in.
OPERATING YOUR VEHICLE Mist Feature • When a single wipe to clear off road mist or spray from a passing vehicle is needed, push the washer knob, located on the end of the multifunction lever, inward to the first detent and release. The wipers will cycle one time and automatically shut off. High Beams • Push the lever away from you to activate the high beams. • A high beam symbol will illuminate in the cluster to indicate the high beams are on.
OPERATING YOUR VEHICLE Cargo Light • The cargo light is strategically placed lighting that helps illuminate the bed area of the truck. A cargo light symbol will illuminate in the cluster to indicate the light is on. • Push the button to turn ON/OFF the cargo lighting. SPEED CONTROL LEVER • The speed control switches are located on the steering wheel. Cruise ON/OFF • Push the ON/OFF switch to activate the Speed Control. • The cruise symbol Speed Control is on.
OPERATING YOUR VEHICLE • Once a speed is set, pushing the RESUME/ACCEL switch once or the DECEL switch once will increase or decrease the set speed approximately 1 mph (2 km/h). Resume • To resume a previously selected set speed in memory, push the RESUME/ ACCEL switch and release. Cancel • Push the CANCEL switch or apply the brakes to cancel the set speed and maintain the set speed memory. • Push the ON/OFF switch to turn the system off and erase the set speed memory.
OPERATING YOUR VEHICLE ELECTRONIC RANGE SELECT (ERS) OPERATION • Electronic Range Select (ERS) allows you to limit the highest available transmission gear, and can be activated during any driving condition. When towing a trailer or operating the vehicle in off-road conditions, using ERS shift control will help you maximize both performance and engine braking.
OPERATING YOUR VEHICLE MANUAL CLIMATE CONTROLS Air Recirculation /Max A/C • Rotate the Temperature Control to the MAX A/C position to automatically turn on both Air Conditioning and Recirculation. • For window defogging, turn the recirculation button off. • Recirculation is not allowed in defrost, floor, defrost/floor (mix) modes. Heated Mirrors • The mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster.
OPERATING YOUR VEHICLE Air Conditioning (A/C) • If the A/C button is pushed while in the AUTO mode, the indicator light may flash three times to indicate the cabin air is being controlled automatically. SYNC Temperature Button • Push the SYNC button once to control the driver and passenger temperatures simultaneously. Push the SYNC button a second time to control the temperatures individually. Air Recirculation • Use recirculation for maximum A/C operation.
OPERATING YOUR VEHICLE PARKVIEW® REAR BACK-UP CAMERA • You can see an on-screen image of the rear of your vehicle whenever the shift lever is put into REVERSE. The ParkView® Rear Back-Up Camera image will be displayed on the radio display screen, located on the center stack of the instrument panel. • If the radio display screen appears foggy, clean the camera lens located on the tailgate. WARNING! Drivers must be careful when backing up even when using the ParkView® Rear Back-Up Camera.
OPERATING YOUR VEHICLE Max Load Inflation (Indicator Light Off) • If the passenger and cargo weights exceed the Light Load Pressure Definition shown on the Supplemental Tire Pressure Information Label, adjust tires to the correct “Max Load Inflation” pressure. If the indicator is on, reset by pushing the switch once.
OPERATING YOUR VEHICLE Manual Open/Close • Press and hold the switch rearward to open or forward to close the sunroof. Any release of the switch will stop the movement, and the sunroof will remain in a partially open or closed position until the switch is pressed again. Venting Sunroof • Press and release the "VENT" button, and the sunroof will open to the vent position. This is called “Express Vent” and will occur regardless of sunroof position.
OPERATING YOUR VEHICLE WIND BUFFETING • Wind buffeting can be described as a helicopter-type percussion sound. If buffeting occurs with the rear windows open, adjust the front and rear windows together. • If buffeting occurs with the sunroof open, adjust the sunroof opening, or adjust any window. This will minimize buffeting.
ELECTRONICS YOUR VEHICLE'S SOUND SYSTEM 30
ELECTRONICS 31
ELECTRONICS Media Center 130 (Sales Code RES) NOTE: • Your radio has many features that add to the comfort and convenience of you and your passengers. Some of these radio features should not be used when driving because they take your eyes from the road or your attention from driving. Clock Setting • Press and hold the “TIME” button until the hours blink; turn the “TUNE/ SCROLL” control knob to set the hours.
ELECTRONICS Store Radio Presets • Press the “SET/RND” button once and SET 1 will show in the display. Then select button (1–6). • A second station may be added to each push button. Press the “SET/RND” button twice and SET 2 will show in the display. Then select button (1–6). CD/DISC Operation Seek Up/Down Buttons • Press to seek through CD tracks. • Hold either button to bypass tracks without stopping. SET/RND Button (Random Play) • Press this button while the CD is playing to activate Random Play.
ELECTRONICS Media Center 130 with Satellite Radio (Sales Code RES + RSC) NOTE: • Your radio may not be equipped with the Uconnect™ Voice Command and Uconnect™ Phone features. To determine if your radio has these features, press the Voice Command button on the radio. You will hear a voice prompt if you have the feature, or see a message on the radio stating “Uconnect Phone not available” if you do not. • Your radio has many features that add to the comfort and convenience of you and your passengers.
ELECTRONICS Radio Operation Seek Up/Down Buttons • Press to seek through radio stations in AM, FM, or SAT bands. • Hold either button to bypass stations without stopping. Store Radio Presets • Press the “SET/RND” button once and SET 1 will show in the display. Then select button (1–6). • A second station may be added to each push button. Press the “SET/RND” button twice and SET 2 will show in the display. Then select button (1–6). Music Type • Press the “MUSIC TYPE” button to activate this mode.
ELECTRONICS • To select a folder from the list, press the “TUNE/SCROLL” control knob and the radio will begin playing the files contained in that folder. Audio Jack Operation • The Audio Jack allows a portable device, such as an MP3 player or a cassette player, to be plugged into the radio and utilize the vehicle’s audio system, using a 3.5 mm audio cable, to amplify the source and play through the vehicle speakers.
ELECTRONICS Clock Setting • Turn the radio on, then touch the screen where the time is displayed. • Touch the “USER CLOCK” soft-key (Navigation radio only). • To adjust the hours, touch either the “HOUR FORWARD” or “HOUR BACKWARD” soft-key. • To adjust the minutes, touch either the “MINUTE FORWARD” or “MINUTE BACKWARD” soft-key. • To save the new time setting, touch the screen where the word “Save” is displayed. Menu • Press the “MENU” hard-key to access the System Setup menu and the My Files menu.
ELECTRONICS • Select the “Auto Color Mode” soft-key to switch to automatic daytime/ nighttime mode and to control the brightness of the display using the dimmer switch of the vehicle. • Touch the “EXIT” soft-key to save your settings. Radio Operation • To access Radio Mode, touch the “RADIO” hard-key on the right side of the faceplate, then touch the “AM,” “FM” or “SAT” soft-key at the top of the screen to select the band.
ELECTRONICS CD/DVD Disc Operation • Press the “MEDIA” hard key to display the media source tabs at the top of the screen. Select the source by touching the “HDD,” “DISC,” or “AUX” media source soft-key tab. NOTE: Your Touch-Screen Radio will usually automatically switch to the appropriate mode when something is first connected or inserted into the system. Insert a CD/DVD Disc • To insert a disc, press the or “LOAD” hard-key. • With the printed side upwards, insert the disc into the disc slot of the radio.
ELECTRONICS • The functions of the portable device are controlled using the device buttons. The volume may be controlled using the radio or portable device. Hard Disk Drive (HDD) Operation • The Hard Disk Drive (HDD) mode gives you access to the audio files on the internal hard disk drive. It functions similar to a CD player, with the exception that the internal HDD can hold more tracks. • It is also possible to import display pictures to the internal hard disk drive.
ELECTRONICS • Select the folders or titles you would like to copy, then touch the “DONE” soft-key to start the copy process. NOTE: The copy progress is shown in the lower left corner of the screen. Copying Pictures To The HDD • Insert either a CD or a USB device containing your pictures in JPEG format. • Press the “MY FILES” hard-key. • Touch the “My Pictures” soft-key to get an overview of the currently stored images, then touch the “Add” soft-key.
ELECTRONICS Cleaning Your Touch-Screen Radio • Do not spray any liquid or caustic chemicals directly on the screen. Use a clean and dry micro fiber lens cleaning cloth in order to clean the touch-screen. • If necessary, use a lint-free cloth dampened with a cleaning solution such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50. Be sure to follow the solvent manufacturer's precautions and directions.
ELECTRONICS Finding A Place By Spelling The Name • From the Main Navigation Menu, touch “Where to?,” then touch “Points of Interest” and then touch “Spell Name.” • Enter the name of your destination. • Touch “Done.” • Select your destination and touch “Go.” Entering A Destination Address • From the main Navigation menu, touch “Where To?,” then touch “Address.” • Follow the on-screen prompts to enter the address and touch “Go.
ELECTRONICS • Touch “Where To?,” then search for the extra stop. Then select the stop to add from the search results. • Touch “Go,” then touch “Add to Current Route.” Taking A Detour • To take a detour you must be navigating a route • Touch the “back arrow” icon to return to the Main Navigation menu. • Touch “Detour.” NOTE: If the route you are currently taking is the only reasonable option, the device might not calculate a detour.
ELECTRONICS Media Center 730N (Sales Code RHR) NOTE: Your radio may not be equipped with the Uconnect™ Voice Command and Uconnect™ Phone features. To determine if your radio has these features, press the Voice Command button on the radio. You will hear a voice prompt if you have the feature, or see a message on the radio stating “Uconnect Phone not available” if you do not. • Your radio has many features that add to the comfort and convenience of you and your passengers.
ELECTRONICS • Press the “MENU” hard-key in an active mode (SAT, CD, AUX, etc.) in order to change mode specific settings. Equalizer, Balance And Fade Audio Control Menu • Press the “MENU” hard-key on the right side of the radio. Then press the “Audio Control” soft-key to get to the audio control menu. • Use either the arrow soft-keys or the cross-hair on the screen to change Balance and Fade. The “CENTER” soft-key resets the settings.
ELECTRONICS Radio Operation • To access Radio Mode, touch the “RADIO/MEDIA” hard-key on the right side of the faceplate repeatedly until AM/FM/SAT appears at the top of the screen, then touch the “AM,” “FM” or “SAT” soft-key to select the band. Seek Up/Seek Down • Press the “Seek Up” or “Seek Down” hard-keys to seek through radio stations in AM, FM, or SAT bands. Hold either Seek to bypass stations without stopping.
ELECTRONICS CD/DVD Disc Operation • Press the “RADIO/MEDIA” hard key until the media source tabs are displayed at the top of the screen. Select the source by touching the “HDD,” “DISC,” or “AUX” media source soft-key tab. NOTE: Your Touch-Screen Radio will usually automatically switch to the appropriate mode when something is first connected or inserted into the system.
ELECTRONICS • The functions of the portable device are controlled using the device buttons. The volume may be controlled using the radio or portable device. Hard Disk Drive (HDD) Operation • The Hard Disk Drive (HDD) mode gives you access to the audio files on the internal hard disk drive. It functions similar to a CD player, with the exception that the internal HDD can hold more tracks. • It is also possible to import display pictures to the internal hard disk drive.
ELECTRONICS • Touch the “MY MUSIC” soft-key, then touch the “Add Music Files” to HDD soft-key. • Touch “Front USB” soft-key, then select the folders or titles you would like to copy, and then touch the “SAVE” soft-key to start the copy process. NOTE: The copy progress is shown in the lower left corner of the screen. Copying Pictures To The HDD • Insert either a CD or a USB device containing your pictures in JPEG format.
ELECTRONICS Playing Music From The HDD • Press the “RADIO/MEDIA” hard key until the media source tabs are displayed at the top of the screen. Touch the “HDD” soft-key tab. Touch the desired track soft-key to play or touch the “SEARCH/BROWSE” soft-key to search by artist, by album, by song, by genre, from a folder, or from Favorites. Cleaning Your Touch-Screen Radio • Do not spray any liquid or caustic chemicals directly on the screen.
ELECTRONICS Main Navigation Menu Finding Points Of Interest • From the NAV main menu, touch the “Points of Interest” soft-key. • Select a Category and then a subcategory, if necessary. • Select your destination and touch “GO.” Finding A Place By Entering The Street Address • From the NAV main menu, touch “New Destination,” then touch “Street Address.” NOTE: If the wrong State and/or Country displayed are incorrect, touch the corresponding soft-key to make the correction.
ELECTRONICS Where Am I Now? • From the NAV main menu, touch “Where Am I Now?.” The Where Am I Now? menu displays location information for the current vehicle position. • Touch the “NEARBY POI”soft-key to search for a local Point of Interest. • Touch the “SAVE LOCATION” soft-key to save the current location in the Saved Locations memory. Route Guidance • After starting route guidance, the system calculates the route and announces: “Follow the arrows on the display.
ELECTRONICS Entering Your Home Location • Press the “NAV” hard-key on the right side of the radio. • From the Nav – Main Menu, touch Guide Me Home to enter your home address. If no home address has been set, touch “YES” to access the Enter Home Address menu. • Touch “Street Address” to enter your address. Touch the soft-key with your state’s name and enter your street name into the speller. • Once the street name has been input, touch “CONTINUE” to confirm. Enter the house number into the next screen.
ELECTRONICS • Media Center 430/430N and 730N: Press the “MENU” hard-key while in SIRIUS Satellite Radio Mode, then touch the “Channel Lock” to enable and/or disable desired channels. The SEEK and SCAN function will then only display channels without Channel lock. Search/Browse • Touch the “magnifying glass” soft-key to search/browse the SIRIUS channel listing by Favorites and Categories such as Song, Artist and Channel Name. The Search/Browse also allows you manage your Favorites.
ELECTRONICS • You may use the “LIST” soft-key to toggle between: • Favorite Songs. • Favorite Artists. • Currently playing favorites. Replay • While you are in SAT mode, you can replay 44 minutes of the current SIRIUS channel (when the channel is changed, this audio buffer is erased). Press the REPLAY button to listen to the stored audio.
ELECTRONICS 1 – Favorites 2 – Forecast 3 – Ski Info 4 – Fuel Prices 5 – Movies 6 – Sports View and store your favorite location, theater and sport teams for quick access. View detailed weather conditions, forecasts and ski/snowboarding conditions at local resorts. View ski and snowboarding conditions at local ski resorts. View detailed price information for fuel stations near your current location. View information on movies that are playing at theaters near your current location.
ELECTRONICS iPod®/USB/MP3 CONTROL • There are many ways to play music from iPod® players or other portable devices through your vehicle's speakers. • The USB port located inside the upper glove box, allows you to plug an iPod® into the vehicle's sound system. • To hear audio from devices connected to this port from a non-touch-screen radio, press the AUX button on the radio faceplate. From a touch-screen radio, press the MEDIA hard-key, then touch the AUX or iPod® soft-key.
ELECTRONICS NOTE: To access the tutorial, press the “Uconnect™ Phone” button . After the BEEP, say “tutorial”. Press any hard-key/button or touch the display (Touch-Screen radio) to cancel the tutorial. • The Uconnect™ Phone allows you to dial a phone number with your mobile phone using simple voice commands. • Refer to your vehicle Owner's Manual on the DVD for further details. NOTE: The Uconnect™ Phone requires a mobile phone equipped with the Bluetooth® Hands-Free Profile, Version 1.0 or higher.
ELECTRONICS Phonebook Phonebook Download – Automatic Phonebook Transfer From Mobile Phone If equipped and specifically supported by your phone, Uconnect™ Phone automatically downloads names (text names) and number entries from your mobile phone’s phonebook. Specific Bluetooth® Phones with Phone Book Access Profile may support this feature. Automatic Transfer is indicated by a green arrow at the bottom of the screen. See Uconnect™ website for supported phones.
ELECTRONICS Mute (Or Unmute) Microphone During Call • During a call, press the “Voice Command” button . • (After the BEEP), say “mute” (or “mute off”). Transfer Ongoing Call Between Handset And Vehicle • During a call, press the “Voice Command” button . • (After the BEEP), say “transfer call”. Changing The Volume • Start a dialogue by pressing the “Phone” button during a normal call.
ELECTRONICS Common Voice Commands (Examples) Main Menu Radio Mode SIRIUS Satellite Radio Mode Disc Mode Memo Mode “Radio” (to switch to the radio mode) “Disc” (to switch to the disc mode) “Memo” (to switch to the memo recorder) “System Setup” (to switch to system setup) “Frequency” (to change the frequency) “Next Station” (to select the next station) “Previous Station” (to select the previous station) “Radio Menu” (to switch to the radio menu) “Main Menu” (to switch to the main menu) “Channel Number” (
ELECTRONICS • Not all phones are compatible with this feature. Refer to the phone compatibility list at www.ramtrucks.com/uconnect. Connected mobile phones must be bluetooth-compatible, and paired with your radio. • Press the “Voice Command” button get started. and after the BEEP, say “SMS” to NOTE: To access the tutorial, press the “Voice Command” button the BEEP, say “tutorial”. Press any hard-key/button or touch the display (Touch-Screen radio) to cancel the tutorial. .
ELECTRONICS VIDEO ENTERTAINMENT SYSTEM (VES)™ System Operation • The screen is located on the headliner behind the front seat. To lower the screen, press the release button located in the rear of the overhead console. • The system may be controlled by the front seat occupants using the touch-screen radio, or by the rear seat occupants using the remote control. • The video screen displays information in a split screen format.
ELECTRONICS Auxiliary Audio/Video Input Jacks • The Aux jacks are located on the rear of the center console. • Connect the video game or other external media devices to the AUX jacks following the color coding for VES™ jacks. • Using either the touch-screen radio or remote control, select AUX from the Rear VES™ Control or Mode Selection screen. • Refer to your vehicle Owner's Manual on the DVD for further details.
ELECTRONICS PROGRAMMABLE FEATURES Electronic Vehicle Information Center (EVIC) – If Equipped • The EVIC can be used to view or change the following settings. Press the or DOWN button until System Setup displays, then press the UP button. Scroll through the settings using the UP or DOWN SELECT button to change the setting. Press the BACK buttons. Press the SELECT button to scroll back to a previous menu or sub menu.
ELECTRONICS • Within 30 seconds, press the driver’s door lock switch in the UNLOCK direction. A single chime will indicate that programming is complete. Sound Horn With Lock • To turn the horn chirp on or off when the doors are locked: • Press the LOCK button for at least 4 seconds, but no longer than 10 seconds. Then, press the PANIC button while still holding the LOCK button. • Release both buttons at the same time.
ELECTRONICS NOTE: • Erasing all channels should only be performed when programming HomeLink® for the first time. Do not erase channels when programming additional buttons. • If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. Programming A Rolling Code • For programming Garage Door Openers that were manufactured after 1995.
ELECTRONICS • Continue to hold both buttons and observe the indicator light. The Homelink® indicator will flash slowly and then rapidly after Homelink® has received the frequency signal from the hand-held transmitter. Release both buttons after the indicator light changes from slow to rapid. • Press and hold the programmed HomeLink® button and observe the indicator light.
ELECTRONICS NOTE: The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet, the inverter should automatically reset. If the power rating exceeds approximately 170 Watts, the power inverter may have to be reset manually. To reset the inverter manually, unplug the device and plug it in again.
ELECTRONICS NOTE: • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded, the fuse protecting the system will need to be replaced. • Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your new vehicle warranty.
OFF-ROAD CAPABILITIES FOUR-WHEEL DRIVE OPERATION Four-Position Transfer Case • Shifting between 2H or 4H and 4L must be made with the transmission in NEUTRAL and the vehicle stopped or rolling at 2 to 3 mph (3 to 5 km/h).
OFF-ROAD CAPABILITIES Shifting Procedure • Shifting between 2H and 4WD AUTO or 4WD LOCK can be made with the vehicle stopped or in motion. • Shifting between 2H or 4H and 4L must be made with the transmission in NEUTRAL and the vehicle stopped or rolling at 2 to 3 mph (3 to 5 km/h). NOTE: It is preferred to have the engine running and the vehicle moving at 2 to 3 mph (3 to 5 km/h).
UTILITY EASY-OFF TAILGATE • To simplify mounting of a camper unit with an overhang, the tailgate can be removed. NOTE: If your vehicle is equipped with a rear camera the electrical connector must be disconnected prior to removing the tailgate. Removing the Tailgate • Disconnect the wiring harness for the rear camera (if equipped). • Unlatch the tailgate and remove the support cables by releasing the lock tang from the pivot.
UTILITY RAMBOX® • The RamBox® system is an integrated pickup box storage and cargo management system consisting of three features: • Integrated box side storage bins • Cargo extender/divider • Bed rail tie-down system RamBox® Integrated Box Side Storage Bins • The cargo storage bins provide watertight, lockable, illuminated storage for up to 150 lbs (68 kg) of evenly distributed cargo. • To open a storage bin, press and release the pushbutton located on the lid.
UTILITY NOTE: Provisions are provided in the bins for cargo dividers and shelf supports. These accessories (in addition to other RamBox® accessories) are available from MOPAR®. RamBox® Storage Bin Cover Emergency Release Lever • As a security measure, a Storage Bin Cover Emergency Release is built into the storage bin cover latching mechanism.
UTILITY • To install the bed extender into the extender position, perform the following: • Lower the tailgate. • Make sure the center handle is unlocked and rotate the center handle vertically in order to release the extender side gates. • Fit the end of the side gate ends onto the pin and handle. • Rotate the handles to the horizontal position to secure into place. Bed Rail Tie-Down System • There are two adjustable cleats on each side of the bed that can be used to assist in securing cargo.
UTILITY WARNING! WARNING! • Always close the storage bin covers when your vehicle is unattended or in motion. • Do not allow children to have access to the storage bins. Once in the storage bin, young children may not be able to escape. If trapped in the storage bin, children can die from suffocation or heat stroke. • In a collision, serious injury could result if the storage bin covers are not properly latched. • Do not use a storage bin latch as a tie down.
UTILITY Ram 1500 4x4 ST 4.7L V-8 6–Speed Automatic Transmission 5.
UTILITY TOW/HAUL MODE • When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting occurs, press the TOW/HAUL switch to select TOW/HAUL mode. This will improve performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in TOW/HAUL mode, transmission upshifts are delayed, and the transmission will automatically downshift (for engine braking) during steady braking maneuvers.
UTILITY INTEGRATED TRAILER BRAKE MODULE • The Integrated Trailer Brake Controller allows you to automatically or manually activate the electronic brakes on properly equipped trailers for greater stopping power on downhill grades. The controller and status display are on the instrument panel to the left of the steering wheel, and the included control lever can activate the trailer brakes independent of the truck's brakes.
UTILITY RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheels OFF The Ground Two-Wheel Drive Models Four-Wheel Drive Models See Instructions • Automatic transmission in PARK Flat Tow NONE NOT ALLOWED • Manual transmission in gear (NOT in NEUTRAL) • Transfer case in NEUTRAL (N) Front Dolly Tow On Trailer Rear ALL NOT ALLOWED OK OK Recreational Towing – Two-Wheel Drive Models • DO NOT flat tow this vehicle.
UTILITY CAUTION! CAUTION! • Towing with the rear wheels on the ground will cause severe transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty. • Do not disconnect the driveshaft because fluid may leak from the transmission, causing damage to internal parts. • Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing.
DIESEL ENGINE BREAK-IN RECOMMENDATIONS • The Cummins® turbocharged diesel engine does not require a break-in period due to its construction. Normal operation is allowed, providing the following recommendations are followed: • Warm up the engine before placing it under load. • Do not operate the engine at idle for prolonged periods. • Use the appropriate transmission gear to prevent engine lugging. • Observe vehicle oil pressure and temperature indicators. • Check the coolant and oil levels frequently.
DIESEL Cold Start Procedure • Turn the ignition switch to the ON position. If the Wait To Start appears in the cluster, wait for the light to turn off before starting. light • In extremely cold weather below 0°F (-18°C) it may be beneficial to cycle the manifold heaters twice before attempting to start the engine. This can be accomplished by turning the ignition OFF for at least five seconds and then back ON after the “Wait To Start Light” has turned off, but before the engine is started.
DIESEL DIESEL EXHAUST BRAKE (ENGINE BRAKING) • The exhaust brake feature will only function when the driver turns the exhaust brake switch to the ON position. • The switch is located on the switch bank below the audio system. • Once the switch is in the ON position and the vehicle is moving faster than 5 mph (8 km/h), the exhaust brake will automatically operate when the driver removes pressure from the accelerator pedal. • Exhaust braking is most effective when the engine RPM is higher.
DIESEL IDLE-UP FEATURE (AUTOMATIC TRANSMISSION ONLY) • The Idle-Up Feature uses the speed control switches to increase engine idle speed and quickly warm the vehicle’s interior. This feature must be enabled by your dealer. See your local dealer. • With the transmission in PARK, the parking brake applied, and the engine running, push the speed control ON/OFF switch on, then push the SET switch. • The engine RPM will go up to 1100 RPM.
DIESEL • When clean fuel is visible, close the drain and switch the ignition to OFF. • Refer to the Owner's Manual on the DVD for further details. Fuel Filter Replacement • With the engine off and a drain pan under the fuel filter drain hose, open the water drain valve 1/4 turn counterclockwise and completely drain fuel and water into the approved container. • Close the water drain valve and remove the lid using a socket or strap wrench; rotate counterclockwise for removal.
DIESEL Perform Service • Your vehicle will require emissions maintenance at a set interval. To help remind you when this maintenance is due, the Electronic Vehicle Information Center (EVIC) will display “Perform Service”. When the “Perform Service” message is displayed on the EVIC it is necessary to have the emissions maintenance performed. Emissions maintenance may include replacing the Closed Crankcase Ventilation (CCV) filter element, and cleaning of the EGR Cooler.
DIESEL COOL–DOWN IDLE CHART Driving Conditions Stop and Go Stop and Go Highway Speeds City Traffic Highway Speeds Uphill Grade 90 TURBOCHARGER "COOL DOWN" CHART Load Turbocharger Temperature Empty Medium Medium Max. GCWR Max. GCWR Max.
WHAT TO DO IN EMERGENCIES 24-HOUR TOWING ASSISTANCE • Dial toll-free 1-800-521-2779 or 1-800-363-4869 for Canadian residents. • Provide your name, vehicle identification number and license plate number. • Provide your location, including telephone number, from which you are calling. • Briefly describe the nature of the problem and answer a few simple questions. • You will be given the name of the service provider and an estimated time of arrival.
WHAT TO DO IN EMERGENCIES • Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue each time the vehicle is restarted as long as the malfunction exists.
WHAT TO DO IN EMERGENCIES BRAKE - Brake Warning Light • The Brake Warning light illuminates when there is either a system malfunction or the parking brake is applied. If the light is on and the parking brake is not applied, it indicates a possible brake hydraulic malfunction, brake booster problem or an Anti-Lock Brake System problem. • Please have your vehicle serviced immediately. WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed.
WHAT TO DO IN EMERGENCIES - Anti-Lock Brake (ABS) Light • This light monitors the Anti-Lock Brake System (ABS). • If the light is not on during starting, stays on, or turns on while driving, we recommend you drive to the nearest service center and have the vehicle serviced immediately. - Electronic Throttle Control (ETC) Light • This light informs you of a problem with the Electronic Throttle Control (ETC) system. • If a problem is detected, the light will come on while the engine is running.
WHAT TO DO IN EMERGENCIES Resetting The Light After Servicing • Turn the ignition switch to the ON/RUN position (do not start engine). • Fully depress the accelerator pedal three times within 10 seconds. • Turn the ignition switch to the OFF/LOCK position. IF YOUR ENGINE OVERHEATS • In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. • On the highways — slow down.
WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING Jack Location • The jack and jack tools are stored under the front passenger seat. Removal • To access the jack and jack tools you must remove the plastic access cover, located on the side of the seat. To remove the cover, pull the front part of the cover (closest to the front of the seat) toward you to release a locking tab. Once the front of the cover is loose, slide the cover toward the front of the seat until it is free from the seat frame.
WHAT TO DO IN EMERGENCIES Reinstalling The Jack And Tools (1500 Series) 1. Lower the jack all the way down by turning the jack turn-screw until the jack is snug. 2. Position the jack and tool bag (unrolled). Make sure the lug wrench is under the jack near the jack turn-screw. 3. Fold the flap and roll the jack tool kit into a cylindrical package (in direction of arrows) and tie to the jack using the tie straps.
WHAT TO DO IN EMERGENCIES 4. Place the jack and tools in the storage position holding the jack by the jack turn-screw, slip the jack and tools under the seat so that the bottom slot engages into the fastener on the floor, and then secure to the floor pan using the wing bolt. Reinstall the plastic cover.
WHAT TO DO IN EMERGENCIES Removing The Spare Tire • Remove the spare tire before attempting to jack up the truck. Attach the wheel wrench to the jack extension tube. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube. Rotate the wheel wrench handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle.
WHAT TO DO IN EMERGENCIES Preparations 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. 2. Turn on the Hazard Warning flasher. 3. Set the parking brake. 4. Place the shift lever into PARK. On four-wheel drive vehicles, shift the transfer case to the 4L position. 5. Turn the ignition OFF. • Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel.
WHAT TO DO IN EMERGENCIES • 1500 Series Trucks When changing a front wheel, place the scissors jack under the rear portion of the lower control arm as shown below. Operate the jack using the jack drive tube and the wheel wrench. The tube extension may be used but is not required.
WHAT TO DO IN EMERGENCIES For 4x2 and 4x4 trucks, when changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle between the wheel and the shock bracket with the drive tubes extending to the rear. Connect the jack tube extension and wheel wrench.
WHAT TO DO IN EMERGENCIES • 2500/3500 Series Trucks For 2500/3500 4x2 series trucks, when changing a front wheel, place the bottle jack under the frame rail behind the wheel. Locate the jack as far forward as possible on the straight part of the frame. Operate the jack using the jack drive tube and the wheel wrench. The tube extension, may be used, but is not required.
WHAT TO DO IN EMERGENCIES Connect the jack tube extension and wheel wrench. NOTE: If the bottle jack will not lower by turning the dial (thumbwheel) by hand, it may be necessary to use the jack drive tube in order to lower the jack. 4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface. 5. Remove the wheel nuts and pull the wheel off.
WHAT TO DO IN EMERGENCIES • On 3500 models with dual rear wheels (DRW), you must first remove the hub caps. The jack handle driver has a hook at one end that will fit in the pry off notch of the rear hub caps. Position the hook and pull out on the ratchet firmly. The hub cap should pop off. The wheel skins can now be removed. For the front hub cap on 3500 models use the blade on the end of the lug wrench to pry the caps off. The wheel skin can now be removed.
WHAT TO DO IN EMERGENCIES • Dual wheel models require a special heavy-duty lug nut tightening adapter (included with the vehicle) to correctly tighten the lug nuts. Also, when it is necessary to remove and install dual rear wheels, use a proper vehicle lifting device. NOTE: When installing a spare tire as part of a dual rear wheel end combination, the tire diameter of the two individual tires must be compared. If there is a significant difference, the larger tire should be installed in a front location.
WHAT TO DO IN EMERGENCIES CAUTION! (Continued) • Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. • Use a back-and-forth motion to remove the hub cap. Do not use a twisting motion when removing the hub cap, damage to the hub cap finish may occur. • The rear hub caps on the dual rear wheel has two pry-off notches.
WHAT TO DO IN EMERGENCIES WARNING! (Continued) • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway, be extremely careful of motor traffic. • To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground. • Raising the vehicle higher than necessary can make the vehicle unstable and cause a collision. It could slip off the jack and hurt someone near it.
WHAT TO DO IN EMERGENCIES Jump-Starting Procedure • Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. • Connect the opposite end of the positive (+) jumper cable to the positive (+) post of the booster battery. • Connect the negative end (-) of the jumper cable to the negative (-) post of the booster battery.
WHAT TO DO IN EMERGENCIES WARNING! • When temperatures are below the freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump-starting because the battery could rupture or explode and cause personal injury. Battery temperature must be brought above the freezing point before attempting a jump-start. • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades.
WHAT TO DO IN EMERGENCIES SHIFT LEVER OVERRIDE • If a malfunction occurs and the shift lever cannot be moved out of the PARK position, you can use the following procedure to temporarily move the shift lever. • Have your vehicle inspected by your local authorized dealer immediately if the shift lever override has been used. Column Shifter • Tilt the steering wheel to the full up position and firmly set the parking brake. • Turn the Key Fob to the ACC or ON/RUN position without starting the engine.
112 Wheels OFF the Ground NONE Front Rear ALL Towing Condition Flat Tow Wheel Lift or Dolly Tow Flatbed 2WD Models BEST METHOD OK If transmission is operable: • Transmission in NEUTRAL • 30 mph (48 km/h)max • 15 miles (24 km) max distance TOWING A DISABLED VEHICLE NOT ALLOWED NOT ALLOWED BEST METHOD • Auto Transmission in PARK • Manual Transmission in gear ( NOT NEUTRAL) • Transfer Case in NEUTRAL • Tow in forward direction 4WD Models WHAT TO DO IN EMERGENCIES
WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE • If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then, move the shift lever back and forth between REVERSE and DRIVE. Using minimal accelerator pedal pressure to maintain the rocking motion, without spinning the wheels, is most effective.
WHAT TO DO IN EMERGENCIES EVENT DATA RECORDER (EDR) • This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.
MAINTAINING YOUR VEHICLE OPENING THE HOOD • Reach into the opening beneath the center of the hood and move the safety latch lever while lifting the hood at the same time. WARNING! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death.
116 3.
4.
5.
6.
MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Gasoline Versions Fluid, Lubricant, or Genuine Part Engine Coolant 3.7L, MOPAR® Antifreeze/ Coolant Five 4.7L Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Engine Coolant 5.7L MOPAR® Antifreeze/ Coolant Five 1500 Models Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Engine Coolant 5.
MAINTAINING YOUR VEHICLE Component Fuel Selection 3.7L, 4.7L Fuel Selection 5.7L Fluid, Lubricant, or Genuine Part 87 Octane 87 Octane Acceptable. 89 Octane Recommended. Engine Oil Filter 3.7L, MOPAR® Engine Oil Filter or equivalent. 4.7L, 5.7L, 6.7L Spark Plug 3.7L ZFR6F-11G (Gap 0.043 in [1.09 mm]) Spark Plug 4.7L Upper Bank — FR8TE2 (Gap 0.039 in [0.99 mm]) Lower Bank — FR8T1332 (Gap 0.051 in [1.30 mm]). Spark Plug 5.7L LZFR5C-11 (Gap 0.043 in [1.
MAINTAINING YOUR VEHICLE Component Transfer Case Transfer Case NVG 246 Only Front Axle 1500 Four-Wheel Drive Models Rear Axle 1500 Models Front and Rear Axle 2500/3500 Models Brake Master Cylinder Power Steering Reservoir 122 Fluid, Lubricant, or Genuine Part MOPAR® ATF+4® Automatic Transmission Fluid or equivalent licensed ATF+4® product. MOPAR® NVG 246 Automatic Transmission Fluid or equivalent. GL-5 SAE 75W-90 MS-9763 or equivalent. MOPAR® Synthetic Gear Lubricant SAE 75W-140 MS-8985.
MAINTAINING YOUR VEHICLE Diesel Versions Component Engine Coolant 6.7L Turbo Diesel Engine Fluid, Lubricant, or Genuine Part MOPAR® Antifreeze/Coolant Five Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Engine Oil with Filter In ambient temperatures below 6.7L Turbo Diesel 0°F (-18°C), 5W-40 synthetic Engine engine oil that meets Chrysler Materials Standard MS-10902 and the API CJ-4 engine oil category is required.
MAINTAINING YOUR VEHICLE Component Engine Fuel Filter 6.7L Turbo Diesel Crankcase Ventilation Filter 6.7L Turbo Diesel Diesel Exhaust Fluid – Chassis Cab Only 124 Fluid, Lubricant, or Genuine Part MOPAR® Fuel Filter or equivalent. Must meet 5 micron rating. Using a fuel filter that does not meet the manufacturers filtration and water separating requirements can severely impact fuel system life and reliability. MOPAR® CCV Filter or equivalent.
X X X 91,000 42 56,000 54 72,000 60 80,000 66 88,000 72 96,000 78 104,000 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 104,000 117,000 130,000 143,000 156,000 169,000 48 64,000 X X X X X X X X X 78,000 36 48,000 Change the automatic transmission fluid and filter if using your vehicle for any of the following: police, taxi, fleet or frequent trailer towing.
126 54 72,000 60 80,000 66 88,000 72 96,000 • Refer to the Owner's Manual on the DVD for the complete maintenance schedule. Flush and replace the engine coolant if not done at 60 months. Flush and replace the engine coolant if not done at 104,000 miles (173 000 km). 78 104,000 X X X X X X X X X X X 104,000 117,000 130,000 143,000 156,000 169,000 48 64,000 X 91,000 42 56,000 X X X 78,000 36 48,000 Inspect and replace PCV valve if necessary.
MAINTAINING YOUR VEHICLE Maintenance Record (Gasoline Engine) Odometer Date Signature, Authorized Service Center 8,000 Miles (13,000 km) or 6 Months 16,000 Miles (26,000 km) or 12 Months 24,000 Miles (39,000 km) or 18 Months 32,000 Miles (52,000 km) or 24 Months 40,000 Miles (65,000 km) or 30 Months 48,000 Miles (78,000 km) or 36 Months 56,000 Miles (91,000 km) or 42 Months 64,000 Miles (104,000 km) or 48 Months 72,000 Miles (117,000 km) or 54 Months 80,000 Miles (130,000 km) or 60 Months 88,000 Miles (1
128 X X X X X X X X X X X X X X 36,000 18 22,500 X X X X X X X X X X 40,000 24 30,000 X X X X 60,000 30 37,500 X X X X X X X X X X 72,000 36 45,000 X X X X 84,000 42 52,500 • Refer to the Owner's Manual on the DVD for the complete maintenance schedule. X X X 24,000 12 15,000 X Or Kilometers: 12,000 6 Miles: 7,500 Or Months: When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed.
MAINTAINING YOUR VEHICLE Maintenance Record (Diesel Engine) Odometer Date Signature, Authorized Service Center 7,500 Miles (12,000 km) or 6 Months 15,000 Miles (24,000 km) or 12 Months 22,500 Miles (36,000 km) or 18 Months 30,000 Miles (40,000 km) or 24 Months 37,500 Miles (60,000 km) or 30 Months 45,000 Miles (72,000 km) or 36 Months 52,500 Miles (84,000 km) or 42 Months 60,000 Miles (96,000 km) or 48 Months 67,500 Miles (108,000 km) or 54 Months 75,000 Miles (120,000 km) or 60 Months 82,500 Miles (132,
MAINTAINING YOUR VEHICLE FUSES Integrated Power Module (fuses) 130
MAINTAINING YOUR VEHICLE The Integrated Power Module is located in the engine compartment near the battery. This center contains cartridge fuses and mini fuses. A description of each fuse and component may be stamped on the inside cover, otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart.
MAINTAINING YOUR VEHICLE Cavity M12 M13 132 Cartridge Fuse Mini Fuse 30 Amp Green 20 Amp Yellow M14 20 Amp Yellow M15 20 Amp Yellow M16 M18 M19 M20 10 Amp Red 15 Amp Blue 25 Amp Natural 15 Amp Blue M21 M22 M23 M25 20 Amp Yellow 10 Amp Red 10 Amp Red 20 Amp Yellow M26 M27 M28 M29 M30 M31 M32 M33 M34 10 Amp Red 10 Amp Red 15 Amp Blue 10 Amp Red 15 Amp Blue 20 Amp Yellow 10 Amp Red 10 Amp Red 10 Amp Red M35 M36 15 Amp Blue 20 Amp Yellow M37 10 Amp Red M38 25 Amp Natural Description Radio/Am
MAINTAINING YOUR VEHICLE CAUTION! • When installing the totally integrated power module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the totally integrated power module and possibly result in a electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating.
MAINTAINING YOUR VEHICLE WHEEL AND WHEEL TRIM CARE • All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. • To remove heavy soil and/or excessive brake dust, use MOPAR® Wheel Cleaner or equivalent or select a non-abrasive, non-acidic cleaner. CAUTION! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheel's protective finish.
CONSUMER ASSISTANCE CHRYSLER GROUP LLC CUSTOMER CENTER P.O. Box 21–8004 Auburn Hills, MI 48321–8004 Phone: 1–866–726–4636 CHRYSLER CANADA INC. CUSTOMER CENTER P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone: 1–800–465–2001 (English) Phone: 1–800–387–9983 (French) ASSISTANCE FOR THE HEARING IMPAIRED • To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center.
CONSUMER ASSISTANCE NOTE: A street address is required when ordering manuals (no P.O. Boxes). NOTE: • The Owner's Manual and User Guide electronic files are also available on the Chrysler, Jeep, Ram Truck and Dodge websites. • Click on the "For Owners" tab, select "Owner/Service Manuals", then select your desired model year and vehicle from the drop down lists. REPORTING SAFETY DEFECTS IN THE 50 UNITED STATES AND WASHINGTON, D.C.
MOPAR ACCESSORIES AUTHENTIC ACCESSORIES BY MOPAR® • The following highlights just some of the many Authentic Ram Truck Accessories by Mopar featuring a fit, finish, and functionality specifically for your Ram Truck. • In choosing Authentic Accessories you gain far more than expressive style, premium protection, or extreme entertainment, you also benefit from enhancing your vehicle with accessories that have been thoroughly tested and factory-approved.
INDEX Adjustable Pedals . . . . . . . . . . . 18 Air Conditioning . . . . . . . . . . 24,25 Airbag . . . . . . . . . . . . . . . . . . 10 Airbag Light . . . . . . . . . . . . . . 94 Alarm, Panic . . . . . . . . . . . . . . . 8 Anti-Lock Brake System (ABS) . . . 94 Arming Theft System (Security Alarm) . . . . . . . . . . . . . . . . . . . 9 Audio Settings . . . . 32,33,34,36,39,48 Automatic Headlights . . . . . . . 20,94 Automatic Temperature Control (ATC) . . . . . . . . . . . . . . . . . . .
INDEX Headlights Automatic . . . . . . . . . . Dimmer Switch . . . . . . . High Beam . . . . . . . . . . Heated Mirrors . . . . . . . . . Heated Steering Wheel . . . . Heater, Engine Block . . . . . High Beam/Low Beam Select (Dimmer) Switch . . . . . . . . . . . . . . . . . . . . . . 20 . . 20 . . 20 24,25 . . 17 . . 84 . . . . 20 HomeLink® (Garage Door Opener) Transmitter . . . . . . . . . . . . . . . 67 Hood Release . . . . . . . . . . . . 115 Hub Caps . . . . . . . . . . . . . . .
INDEX Reporting Safety Defects . . . . . . 136 Restraints, Child . . . . . . . . . . . . 11 Seat Belts . . . . . . . . . . . . . . . . 10 Seats . . . . . . . . . . . . . . . . . . 14 Adjustment . . . . . . . . . . . . . . 15 Lumbar Support . . . . . . . . . . 14 Memory . . . . . . . . . . . . . . . . 15 Power . . . . . . . . . . . . . . . . . 14 Ventilated . . . . . . . . . . . . . . 16 Seek Button . . . . . . . . . . . 32,33,35 Setting the Clock . . . . . . 32,34,37,45 Shift Lever Override . . . . . . . .
FAQ (How To?) FREQUENTLY ASKED QUESTIONS GETTING STARTED • How do I install my LATCH Equipped Child Seat? pg. 11 • How do I program my Front Seat Memory? pg. 15 OPERATING YOUR VEHICLE • How does the Electronic Range Select (ERS) operate? pg. 23 • Where is the Light Load Inflation switch located? pg. 26 ELECTRONICS • Which radio is in my vehicle? pg. 32, 34, 36, 45 • How do I activate the Audio Jack? pg. 33, 36, 39, 48 • How do I set the clock on my radio? pg.
NOTES 142
NOTES 143
NOTES 144
If you are the first registered retail owner of your vehicle, you may obtain a complimentary printed copy of the Owner’s Manual, Navigation/Media Center Manuals or Warranty Booklet by calling 1-866-726-4636 (U.S.) or 1-800-387-1143 (Canada) or by contacting your dealer. RAMTRUCKS.COM The driver’s primary responsibility is the safe operation of the vehicle. Driving while distracted can result in loss of vehicle control, resulting in a collision and personal injury.
RAM TRUCKS 1500/2500/3500 USER GUIDE 2012 Download a FREE electronic copy of the Owner’s Manual or Warranty Booklet by visiting the Ownership tab at: www.ramtrucks.com (U.S.) or www.ramtruck.ca (Canada). 12D241-926-AA Ram Trucks 1500/2500/3500 First Edition User Guide 881505_12_RAM_Truck_1500-2500-3500_User_Guide_050611.
