RAM ram truck T RU CK 2009 2009 OWNER’S MANUAL Chrysler LLC 81-326-0931 148922_09 Dodge Ram Gas.indd 1 Second Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Van Conversions/Campers . . . . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 6 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . . 7 ..............
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 7 VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title. Vehicle Identification Number NOTE: It is illegal to remove the VIN.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 䡵 Vehicle Security Alarm — If Equipped . . . . . . . . 19 ▫ Wireless Ignition Node (WIN) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 12 ▫ Rearming Of The System . . . . . . . . . . . . . . . . 19 ▫ Integrated Ignition Key . . . . . . . . . . . . . . . . . 13 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . 14 ▫ Key-In-Ignition Reminder . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Express Down Window Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 24 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 25 ▫ Programming Additional RKE Transmitters . . . 25 ▫ RKE Transmitter Battery Service . . . . . . . . . . . 25 ▫ General Information . . . . . . . . . . . . . . . . . . . 26 䡵 Remote Starting System — If Equipped . . . . . . . 26 ▫ How To Use Remote Start . . . . . . . . . . . . . . . 27 䡵 Door Locks . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Seat Belts And Pregnant Women . . . . . . . . . . 51 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . 51 ▫ Transporting Passengers . . . . . . . . . . . . . . . . 74 ▫ Driver And Right Front Passenger Supplemental Restraint System (SRS) – Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Remote Keyless Entry (RKE) with Integrated Ignition Key — If Equipped Your vehicle may use a keyless ignition system. This system consists of a Remote Keyless Entry (RKE) transmitter with integrated ignition key and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the double-sided integrated key into the ignition switch with either side up.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Integrated Ignition Key The Integrated Key operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and a Valet Key, which stores in the rear of the RKE transmitter. The Valet Key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead. You can keep the Valet Key with you when valet parking.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To remove the Valet Key from the RKE transmitter, slide the mechanical latch at the top of the RKE transmitter sideways with your thumb and then pull the key out with your other hand. Valet Key Removal NOTE: You can insert the double-sided valet key into the lock cylinder with either side up. Ignition Key Removal Place the shift lever in PARK. Turn the key to the LOCK position and then remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 WARNING! Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle. CAUTION! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all doors when leaving the vehicle unattended.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE During normal operation, after turning on the ignition switch, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb check, it indicates that someone used an invalid key to try to start the engine.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Replacement Keys NOTE: Only keys that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a Sentry Key威 is programmed to a vehicle, it cannot be programmed to any other vehicle. CAUTION! Always remove the Sentry Keys威 from the vehicle and lock all doors when leaving the vehicle unattended. At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN).
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Customer Key Programming If you have two valid RKE transmitters with integrated keys, you can program new RKE transmitters to the system by performing the following steps: 1. Insert the first valid integrated key into the ignition switch and turn the ignition switch to the ON position for at least three seconds, but no longer than 15 seconds. Turn the ignition switch to the LOCK position and remove the first key. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 General Information The Sentry Key威 system complies with FCC rules Part 15 and with RSS-210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received, including interference that may cause undesired operation.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 16 seconds to indicate that the alarm is being set. After the alarm is set, the Vehicle Security Light will flash at a slower rate to indicate that the system is armed. be initiated. To exit the alarming mode, press the RKE transmitter UNLOCK button, or start the vehicle with a programmed Sentry Key威. NOTE: If the Vehicle Security Light stays on continuously during vehicle operation, have the system checked by an authorized dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 NOTE: • The front courtesy overhead console and door courtesy lights do not turn off if the dimmer control is in the interior lights ON position (extreme right position). transmitters will continue to work. Driving at speeds 5 mph (8 km/h) and above disables all RKE transmitter buttons for all RKE transmitters. • The illuminated entry system will not operate if the dimmer control is in the extreme left position.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock the Doors Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door, or twice within five seconds to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Flash Lamps with Remote Key Lock This feature will cause the turn signal lights to flash when the doors are locked or unlocked with the RKE transmitter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • For vehicles equipped with the EVIC, refer to “Flash Lamps Lock” under “Customer-Programmable Features (SETUP)” in the “Electronic Vehicle Information Center (EVIC),” in Section 4 of this manual.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sound Horn with Remote Key Lock This feature will cause the horn to chirp when the doors are locked with the RKE transmitter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • For vehicles equipped with the EVIC, refer to “Horn Chirp” under “Customer-Programmable Features (SETUP)” in the “Electronic Vehicle Information Center (EVIC),” in Section 4 of this manual.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 then immediately press and hold the UNLOCK button until the windows lower to the level desired or until they lower completely. Using the Panic Alarm To turn the Panic Alarm feature ON or OFF, press and hold the PANIC button on the RKE transmitter for at least one second and release. When the Panic Alarm is on, the headlights and park lights will flash, the horn will pulse on and off, and the interior lights will turn on.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. With the RKE transmitter buttons facing down, use a flat blade to pry the two halves of the RKE transmitter apart. Make sure not to damage the seal during removal. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 How To Use Remote Start All of the following conditions must be met before the engine will remote start: • Shift lever in PARK • Doors closed • Hood closed • HAZARD switch off • BRAKE switch inactive (brake pedal not pressed) • Ignition key removed from ignition switch • Battery at an acceptable charge level • RKE PANIC button not pressed Remote Start Abort Message on Electronic Vehicle Information Center (EVIC) — If Equipped) The following messages will disp
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Enter Remote Start Mode Press and release the REMOTE START button on the RKE transmitter twice, within five seconds. The parking lights will flash and the horn will chirp twice (if programmed). Once the vehicle has started, the engine will run for 15 minutes. NOTE: • The park lamps will turn on and remain on during Remote Start mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 • For vehicles equipped with the Electronic Vehicle Information Center (EVIC), the message “Insert Key/ Turn To On” will flash in the EVIC until you insert the key into the ignition swich. Once inserted, the message “Turn To On” will flash in the EVIC until you turn the ignition switch to the ON/RUN position.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 or closing the door will allow the locks to operate. A chime will sound if the key is in the ignition switch and a door is open, as a reminder to remove the key. 2. Fasten your seat belt. (Fastening the seat belt will cancel any chiming that may confuse you during this programming procedure.) Automatic Door Locks – If Equipped If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). 3.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Unlock On Exit — If Equipped This feature unlocks all of the doors of the vehicle when any door is opened. This will occur only after the vehicle has been shifted into the PARK position after the vehicle has been driven (shifted out of PARK and all doors closed).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Child Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the child protection door lock system. clockwise to engage the lock and clockwise to disengage the child protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. WINDOWS Power Windows – If Equipped NOTE: • After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 The control on the left front door panel has UP-DOWN switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of Quad Cab威 and Crew Cab models. The windows will operate when the ignition switch is turned to the ON or ACC position, and for up to 10 minutes after the ignition is turned OFF or a front door is opened.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To open the window part way, press to the first detent and release it when you want the window to stop. Auto Up Feature with Anti-Pinch Protection (4-Door Models Driver’s and Front Passenger Door Only) — If Equipped Lift the window switch to the second detent, release, and the window will go up automatically. To stop the window from going all the way up during the Auto Up operation, push down on the switch briefly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 position. To enable the window controls, press the window LOCK button again and return the switch to the released or up position. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down or partially open positions. This is a normal occurrence and can be minimized.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not allow children to have access to the storage bins. Once in the storage bin, young children may not be able to escape. If trapped in the storage bin, children can die from suffocation or heat stroke. • In an accident, serious injury could result if the storage bin covers are not properly latched. • Do not drive the vehicle with the storage bin covers open.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, side airbags, and front airbags for both the driver and front passenger. All seat belt systems (except driver’s and second row center position) include Automatic Locking Retractors (ALR).
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belts All seating positions except the Quad Cab威 and Crew Cab front center seating position have combination lap/ shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions. But in a collision, the belt will lock and reduce the risk of your striking the inside of the vehicle or being thrown out.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 WARNING! (Continued) • Two people should never be belted into a single seat belt. People belted together can crash into one another in an accident, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size. 2 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Latch Plate To Buckle WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WARNING! (Continued) • A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 belt tongue is pressed into the buckle. Allow the retractor to take up the surplus webbing, and the buckles will hang vertically from the cab back exit bezel, thus freeing up all the area behind the front seats. panel and insert it into the black keyed buckle until there is an audible “click”. For proper seatbelt usage, refer “Lap/Shoulder Belt Operating Instructions” in this section. WARNING! Detaching Buckle With Seat Belt Tongue 2.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Inserting Latch Plate In Use Position
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 WARNING! • If the black latch and black buckle are not properly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision. • When reattaching the black latch and black buckle, ensure the seat belt webbing is not twisted.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Automatic Locking Retractor (ALR) Mode – If Equipped In this mode, the shoulder belt is automatically prelocked. The belt will still retract to remove any slack in the shoulder belt.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 pull. To remove slack, pull the loose end of the webbing. Wear the lap belt snug against the hips. Sit back and erect in the seat, then adjust the belt as tightly as is comfortable. WARNING! • A lap belt worn too loose or too high is dangerous. • A belt worn too loose can allow you to slip down and under the belt in a collision. • A belt that is too loose or too high will apply crash forces to the abdomen, not to the stronger hip bones.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seat belt. The driver should also instruct all other occupants to buckle their seat belts. If the driver unbuckles the seat belt while the vehicle is in motion an immediate chime will be heard and BeltAlert威 will continue to chime and flash the Seat Belt Reminder Light for 96 seconds or until the driver’s seat belt is buckled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Seat Belts and Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug against the hips as possible. Keep the belt low so that it does not come across the abdomen. That way the strong bones of the hips will take the force if there is a collision.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE These airbags are certified to the new Federal regulations that allow less forceful deployments. This vehicle is equipped with side curtain airbags to protect the driver and passengers sitting next to a window. The side curtain airbags are located above the side windows. Their covers are also labeled SRS AIRBAG.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 WARNING! WARNING! (Continued) • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE of the vehicle is triggered in moderate to severe side collisions. In certain types of collisions, both the front and side airbags may be triggered. But even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly. Here are some simple steps you can follow to minimize the risk of harm from a deploying airbag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 WARNING! (Continued) • Side airbags need room to inflate, do not lean against the door. Sit upright in the center of the seat.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The ORC also turns on the Airbag Warning Light in the instrument panel for six to eight seconds when the ignition is first turned on, and then turns the light off. • If the ORC detects a malfunction in any part of the system, it turns on the Airbag Warning Light either momentarily or continuously. WARNING! Ignoring the Airbag Warning Light in your instrument panel could mean you won’t have the airbags to protect you in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 In moderate to severe side collisions, the side airbag inflator on the crash side of the vehicle is triggered, releasing a quantity of nontoxic gas. The side curtain airbag moves at a very high speed and with such a high force, that it could injure you if you are not seated properly, or if items are positioned in the area where the side curtain airbag inflates. This especially applies to children.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. • As the airbags deflate you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Maintaining Your Airbag Systems WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or frame.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the speedometer, tachometer or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. The airbags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. For proper location of airbag fuses, refer to “Fuses (Integrated Power Module)” in Section 7. See your authorized dealer if the fuse is good.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 In the event that an investigation is undertaken by Chrysler LLC (regardless of initiative), the company or its designated representative will first obtain permission of the appropriate custodial entity for the vehicle (usually the vehicle owner or lessee) before accessing the electronic data stored, unless ordered to download data by a court with legal jurisdiction (i.e., pursuant to a warrant).
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Impact acceleration and angle • Seat belt status • Brake status (service and parking brakes) • Accelerator status (including vehicle speed) • Engine control status (including engine speed) • Transmission gear selection • Cruise control status • Traction/stability control status • Tire pressure monitoring system status (if equipped) Child Restraint Everyone in your vehicle needs to be buckled up all the time — babies and children, too.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Infants and Small Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Use the restraint that is correct for your child: • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg).
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE cushion while the child’s back is against the seat back, they should use a belt-positioning booster seat. The child and booster seat are held in the vehicle by the lap/shoulder belt. (Some booster seats are equipped with a front shield and are held in the vehicle by the lap portion.) For further information, refer to www.seatcheck.org. WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Pull the belt from the retractor until there is enough to allow you to pass through the child restraint and slide the latch plate into the buckle. Then pull on the belt until it is completely extended from the retractor. Allow the belt to return to the retractor, pulling on the excess webbing to tighten the lap portion about the child restraint. Refer to ⬙Automatic Locking Retractors (ALR) Mode⬙ in this section.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lower Anchors and Tether for CHildren (LATCH) Each vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tether for CHildren. LATCH child restraint anchorage systems are installed in the Quad Cab威 and Crew Cab rear seat outboard positions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seat back tether anchorage have been available for some time. In fact, many child restraint manufacturers will provide add-on tether strap kits for some of their older products.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing the Child Restraint System WARNING! Do not install child restraint systems equipped with LATCH attachments in the center position of a Quad Cab威 or Crew Cab model rear seat. The LATCH anchorages in this seat are designed for the two outboard seating positions only. A child may be placed in the rear center seating position of a Quad Cab威 or Crew Cab model using the seat belt and child tether anchorage.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 WARNING! WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. An incorrectly anchored tether strap could lead to seat failure and injury to the child.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tether Anchorage Points at the Right and Center Front Seat (Regular Cab - All Seats) 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back under the head restraint to the tether anchor directly behind the seat. 2. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Multiple Child Restraint Installation Sequence (Quad Cab威/Crew Cab - Rear Seats) 1. Obtain tether straps by raising the head restraints and reaching between the rear glass and rear seat. The tether strap may be retained with an elastic band. Accessibility to the tether strap is greatly improved by raising the seat cushion to the “up” position. Remove the elastic before use. 2 2.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Route each tether strap to the anchor behind the center seat, and attach the hooks to the metal ring. • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. 5. Place a child restraint on the center rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat and to the anchor directly behind the right seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 2 Multiple Child Restraint Quad Cab威/Crew Cab 1 2 3 4 5 6 — — — — — — Inner Anchor Strap Ring(s) Snap Hook Tether Strap Passenger’s Side Rear Child Seat Rear Center Child Seat Driver’s Side Rear Child Seat
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-throttle acceleration within the limits of local traffic laws, contributes to a good break-in. Wide-open throttle acceleration in low gear can be detrimental and should be avoided.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 WARNING! (Continued) • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE damaged, have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubrication or oil change. Replace as required.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Periodic Safety Checks You Should Make Outside The Vehicle Door Latches Check for positive closing, latching, and locking. Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tread and sidewall for cuts and cracks. Check the wheel nuts for tightness. Check the tires (including spare) for proper pressure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 85 ▫ Automatic Dimming Mirror — If Equipped . . . 86 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . 86 ▫ Outside Mirrors Folding Feature . . . . . . . . . . 87 ▫ Power Mirrors — If Equipped . . . . . . . . . . . . 88 ▫ Heated Mirrors — If Equipped . . . . . . . . . . . .
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Voice Recognition System (VR) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 119 ▫ Voice Recognition System (VR) Operation . . . 119 ▫ 40-20-40 Front Bench Seat — If Equipped . . . 132 䡵 Driver Memory Seat — If Equipped . . . . . . . . 133 ▫ Commands . . . . . . . . . . . . . . . . . . . . . . . . 121 ▫ Setting Memory Positions And Linking RKE Transmitter To Memory . . . . . . . . . . . . . . . . 133 ▫ Voice Training . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 ▫ Parking Lights And Panel Lights . . . . . . . . . 141 䡵 Tilt Steering Column . . . . . . . . . . . . . . . . . . . 148 ▫ Fog Lights — If Equipped . . . . . . . . . . . . . . 141 䡵 Heating Steering Wheel — If Equipped . . . . . . 149 ▫ Interior Lights . . . . . . . . . . . . . . . . . . . . . . 142 䡵 Driver Adjustable Pedals — If Equipped . . . . . 150 ▫ Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . 143 ▫ Adjustment . . . . . . . . . . . .
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Rear Park Assist Warning Display . . . . . . . . 155 ▫ Using HomeLink威 . . . . . . . . . . . . . . . . . . . 168 ▫ Enable/Disable The Rear Park Assist . . . . . . 158 ▫ Reprogramming A Single HomeLink威 Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 ▫ Service The Rear Park Assist . . . . . . . . . . . . 159 ▫ Cleaning The Rear Park Assist . . . . . . . . . . . 159 䡵 Rear Backup Camera — If Equipped . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . 172 䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . 173 ▫ Glove Box Storage . . . . . . . . . . . . . . . . . . . 181 ▫ Sunroof Fully Closed . . . . . . . . . . . . . . . . . . 173 ▫ Door Storage . . . . . . . . . . . . . . . . . . . . . . . 183 䡵 Electrical Power Outlets . . . . . . . . . . . . . . . . .
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Rear Window Features . . . . . . . . . . . . . . . . . . 189 ▫ Bed Rail Tie-Down System . . . . . . . . . . . . . . 203 ▫ Rear Window Defroster And Heated Sideview Mirrors — If Equipped . . . . . . . . . 189 䡵 Slide-In Campers . . . . . . . . . . . . . . . . . . . . . . 205 ▫ Power Sliding Rear Window — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 189 ▫ Sliding Rear Window — If Equipped . . . . . . 189 䡵 Fold Flat Load Floor — If Equipped .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 MIRRORS Inside Day/Night Mirror Headlight glare can be reduced by moving the small control lever under the mirror to the night position (lever flipped toward the rear of vehicle). Adjusting Rearview Mirror The mirror should be adjusted with the lever set in the day position (lever flipped toward the windshield). The mirror should be adjusted to center on the view through the rear window.
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the power button at the base of the mirror. A light in the button will illuminate when the dimming feature is activated. CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 WARNING! Vehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side convex mirror. Some vehicles will not have a convex right side mirror.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Mirrors — If Equipped The controls for the power mirrors are located on the driver’s door trim panel. Power Mirror Controls 1 — Mirror Select Buttons 2 — Mirror Control Power Mirror Controls The power mirror controls consist of mirror select buttons and a four-way mirror control switch. To adjust a mirror, press the mirror select button for the mirror that you want to adjust.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 Illuminated Vanity Mirror — If Equipped Illuminated vanity mirrors are located on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on automatically. Closing the mirror cover turns off the light. Power Mirror Movement Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Slide On Rod Features of Sun Visor — If Equipped The sun visor “Slide-On Rod” feature allows for additional flexibility in positioning the visor to block out the sun. To use the slide on rod feature, rotate the sun visor downward and unclip it. Pull the sun visor along the “Slide On Rod” until the sun visor is in the desired position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 uconnect威 phone is a voice-activated, hands-free, invehicle communications system. uconnect威 allows you to dial a phone number with your cellular phone using simple voice commands (e.g., ⬙Call” ѧ “Mike” ѧ”Work⬙ or ⬙Dial” ѧ “248-555-1212⬙). Your cellular phone’s audio is transmitted through your vehicle’s audio system; the system will automatically mute your radio when using the uconnect威 phone.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone Button The rearview mirror contains the microphone for the system (depending on the type of mirror and radio equipped), and either the radio or the mirror has the two control buttons (PHONE Button and VOICE RECOGNITION button) that will enable you to access the system. Voice Recognition Button Actual button location may vary with the radio. The individual buttons are described in the “Operation” section.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 • For certain operations, compound commands can be used. For example, instead of saying ⬙Setup⬙ and then ⬙Phone Pairing,⬙ the following compound command can be said: ⬙Setup Phone Pairing.⬙ • For each feature explanation in this section, only the combined form of the voice command is given. You can also break the commands into parts and say each part of the command when you are asked for it.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To complete the pairing process, you will need to reference your cellular phone Owner’s Manual. The uconnect威 website may also provide detailed instructions for pairing. • For identification purposes, you will be prompted to give the uconnect威 phone a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Dial by Saying a Number • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Dial.⬙ • The system will prompt you to say the number you want to call. • For example, you can say ⬙234-567-8901⬙. • The uconnect威 phone will confirm the phone number and then dial. The number will appear in the display of certain radios. Call by Saying a Name • Press the PHONE button to begin.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook New Entry.⬙ • When prompted, say the name of the new entry. Use of long names helps the voice recognition and it is recommended. For example, say ⬙Robert Smith⬙ or ⬙Robert⬙ instead of ⬙Bob.⬙ • When prompted, enter the number designation (e.g., ⬙Home,⬙ ⬙Work,⬙ ⬙Mobile,⬙ or ⬙Pager⬙). This will allow you to store multiple numbers for each phonebook entry, if desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 • Automatic download and update, if supported, begins as soon as the Bluetooth威 wireless phone connection is made to the uconnect威 phone, for example, after you start the vehicle. • A maximum of 1000 entries per phone will be downloaded and updated every time a phone is connected to the uconnect威 phone. • Depending on the maximum number of entries downloaded, there may be a short delay before the latest downloaded names can be used.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • The phone handset must support Bluetooth威 OBEX transfers of phonebook entries to use this feature. • Some phones cannot send phonebook entries if they are already connected to any system via Bluetooth威, and you may see a message on the phone display that the Bluetooth威 link is busy. In this case, the user must first disconnect or drop the Bluetooth威 connection to the uconnect威 phone, and then send the address book entry via Bluetooth威.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or return to the main menu. ⬙Phonebook Edit⬙ can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a cellular and a home number, but you can add ”John Doe’s” work number later using the ⬙Phonebook Edit⬙ feature.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete/Erase “All” uconnect威 Phonebook Entries List All Names in the uconnect威 Phonebook • Press the PHONE button to begin. • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook Erase All.⬙ • After the ⬙Ready⬙ prompt and the following beep, say ⬙Phonebook List Names.⬙ • The uconnect威 phone will ask you to verify that you wish to delete all the entries from the phonebook.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Phone Call Features The following features can be accessed through the uconnect威 phone if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the uconnect威 phone. Check with your cellular service provider for the features that you have.
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Making a Second Call While Current Call is in Progress To make a second call while you are currently on a call, press the VOICE RECOGNITION button and say ⬙Dial⬙ or ⬙Call⬙ followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to ⬙Toggling Between Calls⬙ in this section. To combine two calls, refer to ⬙Conference Call⬙ in this section.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Call Termination To end a call in progress, momentarily press the PHONE button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the far end, a call on hold may not become active automatically. This is cell phone-dependent. To bring the call back from hold, press and hold the PHONE button until you hear a single beep. Redial • Press the PHONE button to begin.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE uconnect姞 phone Features Language Selection To change the language that the uconnect威 phone is using: • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say the name of the language you wish to switch to English, Espanol, or Francais. • Continue to follow the system prompts to complete the language selection. After selecting one of the languages, all prompts and voice commands will be in that language.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area. • If supported, this number may be programmable on some systems. To do this, press the PHONE button and say ‘Setup’, followed by ‘Emergency’. • The uconnect威 phone does slightly lower your chances of successfully making a phone call as to that for the cell phone directly.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Paging To learn how to page, refer to ⬙Working with Automated Systems.⬙ Paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the uconnect威 phone. Voice Mail Calling To learn how to access your voice mail, refer to ⬙Working with Automated Systems.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 send the corresponding phone number associated with the phonebook entry, as tones over the phone. NOTE: • You may not hear all of the tones due to cellular phone network configurations. This is normal. • Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the uconnect威 phone (while dialing via the cellular phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth威 cellular phone, the audio will be played through your vehicle’s audio system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Advanced Phone Connectivity List Paired Cellular Phone Names Transfer Call to and from Cellular Phone The uconnect威 phone allows ongoing calls to be transferred from your cellular phone to the uconnect威 phone without terminating the call. To transfer an ongoing call from your uconnect威 phone paired cellular phone to the uconnect威 phone or vice versa, press the VOICE RECOGNITION button and say ⬙Transfer Call.⬙ • Press the PHONE button to begin.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Select Another Cellular Phone This feature allows you to select and start using another phone paired with the uconnect威 phone. • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Select Phone⬙ and follow the prompts. • You can also press the VOICE RECOGNITION button at any time while the list is being played, and then choose the phone that you wish to select.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Things You Should Know About Your uconnect姞 phone uconnect威 phone Tutorial To hear a brief tutorial of the system features, press the PHONE button and say “uconnect威 Tutorial.” Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers, the uconnect威 phone Voice Training feature may be used. To enter this training mode, follow one of the two following procedures: From outside the uconnect威 phone mode (e.g.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Speak normally, without pausing, just as you would speak to a person sitting a few feet/meters away from you. • When navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say ⬙Send.⬙ • Make sure that no one other than you is speaking during a voice recognition period. • Storing names in the phonebook when the vehicle is not in motion is recommended.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the uconnect威 phone.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 3
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home 3
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call uconnect威 Tutorial try again voice training work yes
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When you press the VR button, you will hear a beep. The beep is your signal to give a command. NOTE: If you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the VR button, listen for the beep, and say your command. Pressing the VR button while the system is speaking is known as “barging in.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Commands The Voice Recognition system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the Volume 1. Start a dialogue by pressing the VR button. 2. Say a command (e.g., “Help”). 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the Voice Recognition system is speaking.
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Radio FM To switch to the FM band say “FM” or “Radio FM”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Memo To switch to the voice recorder mode say “Memo”. In this mode, you may say the following commands: • “New Memo” (to record a new memo) — During the recording you may press the VR button to stop recording. You proceed by saying one of the following commands: − “Previous” (to play the previous memo) − “Delete” (to delete a memo) • “Delete All” (to delete all memos) System Setup To switch to system setup say “Setup”.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Keep in mind that you have to press the VR button first and wait for the beep before speaking the “Barge In” commands. Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers, uconnect威 phone Voice Training feature may be used. 1. Press the VR button, say “System Setup” and once you are in that menu then say “Voice Training.” This will train your own voice to the system and will improve recognition. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Manual Seat Adjuster — If Equipped Both front seats are independently adjustable forward or rearward and are equipped with a seatback recliner. The manual forward or rearward seat adjustment handle is found at the front edge of each seat cushion. Pull up on the handle and slide the seat forward or backward to move the seat into the most comfortable position.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. Manual Reclining Seats — If Equipped The recliner handle is on the outside of the seat cushion and is used to adjust the seatback position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 WARNING! WARNING! (Continued) • Actuating the recliner handle will allow the seatback to swing (dump) forward on manual recliner seats. Do not stand or lean in front of the seat while actuating the handle. The seatback may swing forward and hit you causing injury. This dump feature allows access to the storage bin behind the seat. To avoid injury, place your hand on the seatback and actuate the handle then position the seatback in the desired position.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints Head restraints can reduce the risk of neck injury in the event of impact from the rear. Pull up or push down on the restraints so that the upper edge is as high as practical, at least to the level of the ears. To lower the head restraint, push in the button and then push down on the head restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Ten-Way Power Seats — If Equipped The power seat controls are on the outboard side of the front seat cushions. The power seat switch can be moved forward and backward as well as up and down to control the position of the seat. The power seatback switch is used to adjust the angle of the seatback to position yourself in the most comfortable driving position. Push forward or rearward on the switch and the seatback will move in either direction.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not put anything under a power seat. It may cause damage to the seat or the seat controls. Power Lumbar — If Equipped The lumbar controls are located on the outboard side of the seat cushion. The lumbar support can be increased by pressing the front of the switch and decreased by pressing the back of the switch. Lumbar Control Switch Heated Seats — If Equipped Both front seats and rear passenger seats can be equipped with heaters.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Press the switch once to choose High heat, press it a second time to choose Low heat. Pressing the switch a third time will turn the heater Off. When High heat is selected both lights on the switch will illuminate. When Low heat is selected one light will be illuminated. NOTE: The engine must be running for the heated seats to operate. The heated seats switch from High to Low and from Low to Off automatically, based on time and temperature of the seat.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ventilated Seats — If Equipped Located in the seat cushion and seatback are small fans that draw the air from around the occupant and exhaust it underneath the seat and into the passenger compartment. The fans draw this air across the surface of the seat using air ducts and fine perforations in the covering to help keep the driver cooler in higher ambient temperatures.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 DRIVER MEMORY SEAT — IF EQUIPPED The memory seat buttons are located on the outboard side of the drivers seat cushion. Automatic Temperature Control (ATC) temperature setting and radio station preset settings. Your Remote Keyless Entry (RKE) transmitters can also be programmed to recall the same positions when the UNLOCK button is pressed. NOTE: The power lumbar option is not programmable with driver memory seats.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Turn the vehicle key to the ON/RUN position. 2. Adjust the driver’s seat, recliner, and both sideview mirrors to the desired positions. performed within 10 seconds if you desire to also use a RKE transmitter to recall memory positions. 8. Turn the ignition OFF and remove the key. NOTE: Not all motors may be moved at one time. Refer to the ten-way power seat description in this section. 9. Press and release the LOCK button on one of the RKE transmitters.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 To recall the memory settings for driver one, press memory button number 1 on the driver’s seat or the UNLOCK button on the RKE transmitter linked to memory position 1. To recall the memory setting for driver two, press memory button number 2 on the driver’s seat or the UNLOCK button on the RKE transmitter linked to memory position 2.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Self-Limiting Control The memory system includes a self-limiting control for full travel positioning of power seat and adjustable pedal movement (all directions). This self-limiting control may, however, develop an unintended movement limitation if an obstruction is encountered sometime during usage. One example of such an occurrence may include a box or package obstructing the full rearward movement of the driver’s seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. 1. Pull the hood release lever located below the steering wheel at the base of the instrument panel. 2. Reach into the opening beneath the center of the hood and push the safety latch inboard to release it, before raising the hood.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. LIGHTS The headlight switch is located on the left side of the instrument panel, next to the steering wheel. The headlight switch controls the operation of the headlights, parking lights, instrument panel lights, cargo lights and fog lights (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Your vehicle is equipped with plastic headlight and fog light (if equipped) lenses that are lighter and less susceptible to stone breakage than glass lights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch to the A (AUTO) position. 90 seconds after you turn the ignition switch to the OFF position. To turn the automatic headlights off, turn the headlight switch out of the AUTO position. NOTE: The engine must be running before the headlights will turn on in the Automatic Mode.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Parking Lights and Panel Lights To turn on the parking lights and instrument panel lights, rotate the headlight switch clockwise. To turn off the parking lights, rotate the headlight switch back to the O (Off) position. 3 Fog Lights — If Equipped The fog lights are turned on by placing the headlight rotary control in the parking light or headlight position and pushing in the headlight rotary control.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE turn off when the switch is pushed a second time, when the headlight switch is rotated to the off position, or the high beam is selected. Interior Lights Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the bottom of the switch) is rotated to the far right detent position, or if equipped, when the UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Cargo Light The cargo lights are turned on by pressing on the cargo button. Lights-on Reminder If the headlights, parking lights, or cargo lights are left on after the ignition is turned OFF, a chime will sound when the driver’s door is opened. Battery Saver To protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights (DRL) (Canada Only and Fleet Vehicles) The headlights on your vehicle will illuminate when the engine is started and the transmission is in any gear except PARK. This provides a constant ⬙Lights ON⬙ condition until the ignition is turned OFF. The lights illuminate at less than 50% of normal intensity. If the parking brake is applied, the Daytime Running Lights (DRL) will turn OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Lane Change Assist Tap the multifunction lever once and the turn signal (left or right) will flash three times, and automatically turn off. Flash-To-Pass You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steering wheel. This will cause the high beam headlights to turn on until the lever is released.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE High Beam/Low Beam Select Switch Push the multifunction lever toward the instrument panel to switch the headlights to high beam. Pulling the multifunction back toward the steering wheel will turn the low beams back on, or shut the high beams off. High Beam/Low Beam WINDSHIELD WIPERS AND WASHERS Windshield Wipers The wipers and washers are operated by a switch in the multifunction lever. Turn the end of the handle to select the desired wiper speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable. For maximum delay between cycles, rotate the control knob into the upper end of the delay range. The delay interval decreases as you rotate the knob until it enters the low continual speed position.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Washers To use the windshield washer, push the washer knob, located on the end of the multifunction lever, inward to the second detent. Washer fluid will be sprayed until the washer knob is released from this position. If the washer knob is depressed while in the delay range, the wiper will operate for several seconds after the washer knob is released. It will then resume the intermittent interval previously selected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident. Adjust the column only while the vehicle is stopped. Be sure it is locked before driving. HEATING STEERING WHEEL — IF EQUIPPED The steering wheel contains a heating element that helps warm your hands in cold weather. The heated steering wheel has only one temperature setting.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions must exercise care when using the steering wheel heater. It may cause burns even at low temperatures, especially if used for long periods. • Do not place anything on the steering wheel that insulates against heat, such as a blanket or cushion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. Adjustable Pedals Switch NOTE: The pedals cannot be adjusted when the vehicle is in REVERSE or when the Electronic Speed Control is set.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Speed Control system can be reactivated by pushing the Electronic Speed Control switch ON/OFF button and resetting the desired vehicle set speed. To Active Push the ON/OFF button (located in the end of the lever) once and the cruise indicator light (located in the message window of the cluster) will illuminate showing that the Electronic Speed Control system is on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 To Set A Desired Speed When the vehicle has reached the desired speed, press the SET lever downward and then release. Lift your foot off the accelerator and the vehicle will operate at the selected speed. Varying The Speed Setting When the Electronic Speed Control is SET, speed can be increased by raising and holding the RESUME/ACCEL lever upwards. When released, a new set speed will be established.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tapping the Electronic Speed Control lever SET/DECEL downward once will result in a 1 mph (1 km/h) speed decrease. Each time the Electronic Speed Control lever is tapped downward, speed decreases. To Accelerate For Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: The Electronic Speed Control system maintains speed up and down hills.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 vehicle speed is increased to approximately 11 mph (18 km/h) or above. The system will be active again if the vehicle speed is decreased to speeds less than approximately 10 mph (16 km/h). Rear Park Assist Sensors The four Rear Park Assist sensors, located in the rear bumper, monitor the area behind the vehicle that is within the sensors field of view.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The system dimly illuminates the two inner most yellow LEDs when it is ON and there are no obstacles being detected. The following chart shows the warning display operation when the system is detecting an obstacle: WARNING DISPLAY DISTANCES DISPLAY LED Inner LED 1st LED 2nd LED 3rd LED 4th LED 5th LED 6th LED 7th LED OBSTACLE DISTANCE FROM: REAR CORNERS REAR CENTER 79 in (200 cm) 51.1 in (130 cm) 45.2 in (115 cm) 31.5 in (80 cm) 39.3 in (100 cm) 25.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 WARNING! WARNING! (Continued) • Drivers must be careful when backing up, even when using the Rear Park Assist. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • The Rear Park Assist is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using the Rear Park Assist to be able to stop in time when the obstacle is detected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 On vehicles equipped with an Electronic Vehicle Information Center (EVIC) the message “Park Assist Disabled” will be displayed on the EVIC when the system has been disabled. Refer to “Electronic Vehicle Information Center (EVIC) — If Equipped” in Section 4. Service The Rear Park Assist When the Rear Park Assist is defective, the EVIC will display the “SERVICE PARK ASSIST SYSTEM” message along with a single chime once per ignition cycle.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! Drivers must be careful when backing up even when using the Rear Camera System. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up. You are responsible for the safety of your surroundings and must continue to pay attention while backing up. Failure to do so can result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Turning the Rear Camera On or Off — With Navigation Radio Turning the Rear Camera On or Off — Without Navigation Radio 1. Press the ⬙menu⬙ hard key. 1. Press the ⬙menu⬙ hard key. 2. Select ⬙system setup⬙ soft key. 2. Select ⬙system setup⬙ soft key. 3. Press the “camera setup” soft key. 3. Enable or disable the rear camera feature by selecting ⬙enable rear camera in reverse⬙ soft key. 4.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE — IF EQUIPPED The overhead console is located on the headliner above the review mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 (RKE) transmitter, if equipped. These lights are also operated individually as reading lights by pressing on the corresponding lens. 3 Rear Passenger Courtesy/Reading Light Front Courtesy/Reading Lights NOTE: The courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED HomeLink威 replaces up to three remote controls (handheld transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLink威 unit operates off your vehicle’s battery. The HomeLink威 buttons are located in the overhead console, and contain one, two, or three dots/lines designating the different HomeLink威 channels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 WARNING! • Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the handheld transmitter 1 to 3 in (3 to 8 cm) from the Homelink威 buttons while keeping the EVIC display in view. NOTE: Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section. For optimal training, point the battery end of the handheld transmitter away from the HomeLink威 4. Press and hold the just-trained HomeLink威 button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door). 6. Firmly press and release the “learn” or “training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Reprogramming A Single HomeLink姞 Button To reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink威 button for 20 seconds until the EVIC display states “CHANNEL # TRAINING.” Do not release the button. 3. Without releasing the button, proceed with Programming HomeLink威 Step 2 and follow all remaining steps.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: POWER SUNROOF — IF EQUIPPED The power sunroof switch is located on the overhead console between the courtesy/reading lights. 1. This device may not cause harmful interference 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE sunroof will automatically retract. Remove the obstruction if this occurs. Next, press the switch forward and release to Express Close. Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing, press the switch forward and hold for two seconds after the reversal occurs.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 Sunroof Maintenance Use only a nonabrasive cleaner and a soft cloth to clean the glass panel. • Inside the top storage tray — with floor mounted shifter. Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed. 3 ELECTRICAL POWER OUTLETS The auxiliary 12-Volt power outlets can provide power for in-cab accessories designed for use with the standard “cigar lighter” plug.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Inside the upper lid of the center storage compartment — if equipped. Power Outlet — Rear Center Console Power Outlet — Upper Lid • Rear of the center console storage compartment — Quad Cab威 or Crew Cab. The power outlet(s) have a fused direct feed from the battery to receive power whether the ignition is ON or OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 NOTE: If desired, all of the power outlets can be converted by your authorized dealer to provide power with the ignition switch in the ON position only. WARNING! To avoid serious injury or death: • Do not use a three-prong adapter. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CIGAR LIGHTER AND ASH RECEIVER — IF EQUIPPED A removable ash receiver and cigar lighter are available. For vehicles with a bench seat the cupholder tray can be used to hold the ash receiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 For vehicles equipped with an optional floor shifter. Optional Floor Shifter 1 — Cigar Lighter 2 — Ash Receiver POWER INVERTER OUTLET — IF EQUIPPED A 115-Volt (150 Watts Maximum) outlet is located on the center stack of the instrument panel, to the right of the radio. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • When the power inverter switch is pressed, there will be a delay of approximately one second before the power inverter status indicator turns on. The status indicator of the AC power inverter indicates whether the inverter is producing AC power. • Due to built-in overload protection, the power inverter will shut down if the power rating is exceeded. WARNING! Power Inverter Outlet To turn on the power outlet, press the switch once.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 CUPHOLDERS Front Instrument Panel Cupholders — (40–20–40 Seats) The cupholders are located in the pull out tray located on the center stack of the instrument panel. Front Cupholders Front Instrument Panel Cupholders — Floor Mounted Shifter For vehicles equipped with bucket seats and a floor mounted shifter there are two cupholders located in the floor console.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Cupholder — Quad Cab姞 Quad Cab威 vehicles may be equipped with a rear cupholder that consists of two cup wells for rear passenger convenience. Rear Cupholder — Crew Cab Crew Cab vehicles are equipped with rear cupholders located in the center armrest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 STORAGE Glove Box Storage The glove box is located on the passenger side of the instrument panel and features both an upper and lower storage area.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the upper glove box push upward on the handle release. The glove box door will automatically open. To open the lower glove box, pull on the handle to release the latch and lower the door.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 Door Storage Front Door Storage — If Equipped Storage areas and bottle holders (drivers side only) are located in the door trim panels. Rear Door Storage — Quad Cab威/Crew Cab Storage compartments are located in both the driver and passenger door trim panels.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Center Storage Compartment — If Equipped The center storage compartment is located between the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and lower storage area. Center Storage Compartment WARNING! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or an accident. Only use the center seating position when the armrest is fully upright.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 Pull on the upper handle on the front of the armrest to raise the cover. The upper storage area contains a 12-Volt power outlet that can be used to power small electrical devices, refer to “Electrical Power Outlets” in this Section for more information. With the upper lid closed, pull on the lower handle to open the lower storage bin.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second Row In-Floor Storage Bin — If Equipped In-floor storage bins are located in front of the second row seats and can be used for extra storage. The storage bins have removable liners that can be easily removed for cleaning. In-Floor Storage Bin And Latch To open in-floor storage bin, lift upward on the handle of the latch and open the lid. NOTE: The front seat may have to be moved forward to fully open the lid.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Seatback Storage Located in the back of both the driver and passenger front seats are pockets that can be used for storage. Storage (Regular Cab) The storage bin is located behind the front seats and runs the length of the cab.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage and Seats (Crew Cab) The Crew Cab models provide additional storage under the rear seats. Lift the seats to access the storage compartment. Plastic Grocery Bag Retainers (Regular Cab Models) Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 REAR WINDOW FEATURES Rear Window Defroster and Heated Sideview Mirrors — If Equipped The electric rear window defroster and heated sideview mirrors are activated by pressing the heated grid button, located on the Climate Control panel, with the ignition ON. Turning OFF the ignition will deactivate the electric rear window defroster and heated sideview mirrors feature. These features also turn off after activation, when 15 minutes have elapsed.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE FOLD FLAT LOAD FLOOR — IF EQUIPPED Quad Cab威 models with a 60/40 rear seat may be equipped with a folding load floor. Unfolding the Load Floor 1. Lift the 60/40 seat cushion(s) to the upward position. WARNING! Do not operate the vehicle with loose items stored on the load floor. While driving or in an accident you may experience abrupt stopping, rapid acceleration, or sharp turns.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. Positioning the Load Floor for Storage Access Under the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor. 3. Lift the load floor up to access storage under the load floor. Load Floor In Open Position 3. Reverse the procedure to store the load floor.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not drive with the load floor in the up position. When stopping fast or in an accident, the load floor could move to the down position causing serious injury. 4. Reverse the procedure to put the load floor back in the secured down position before you operate the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 Rambox Integrated Box Side Storage Bins Cargo storage bins are located on the both sides of the pickup box. The cargo storage bins provide watertight, lockable, illuminated storage for up to 150 lbs (68 kg) of evenly distributed cargo. Rambox Cargo Storage Bins CAUTION! Failure to follow the following items could cause damage to the vehicle. • Assure that all cargo inside the storage bins is properly secured.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open a storage bin, press and release the pushbutton located on the lid. The Rambox lid will open upward to allow hand access. Lift the lid to fully open. located at the rear of each storage bin. Pushing the switch once will turn off the bin lights, pushing the switch again will turn the lights back on. Rambox Pushbutton and Lock Rambox Light Switch The interior of the Rambox will automatically illuminate when the lid is opened.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 CAUTION! Leaving the lid open for extended periods of time could cause the vehicle battery to discharge. If the lid is required to stay open for extended periods of time, it is recommended that the bin lights be turned off manually using the on/off switch. The Rambox storage bins can be locked using the vehicle key. To lock the storage bin, insert the key into the keyhole on the pushbutton and turn clockwise to lock.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To install the bed extender into the storage position, perform the following: 1. Make sure the center handle is unlocked using the vehicle key and rotate the center handle vertically to release the extender side gates.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 2. With the side gates open, position the extender fully forward in the bed against the front panel. 3. Rotate the side gates closed allowing the outboard ends to be positioned in front of the cargo tie down loops.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Rotate the center handle horizontally to secure the side gates in the closed position. Divider Position The divider position is intended for managing your cargo and assisting in keeping cargo from moving around the bed. There are 11 divider slots along the bed inner panels which allow for various positions to assist in managing your cargo. To install the bed extender into a divider position perform the following: 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 2. With the side gates open, position the extender so the outboard ends align with the intended slots in the sides of the bed. 3 Center Handle and Lock 1 — Center Handle Lock 2 — Handle Aligning Gate To Slots 3. Rotate the side gates closed so that the outboard ends are secured into the intended slots of the bed.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Rotate the center handle horizontally to secure the side gates in the closed position. Side Gates Closed 5. Lock the center handle to secure the panel into place and assist against theft. Extender Position The extender position allows you to load the bed of the truck beyond the tail gate. The bed extender will add an additional 15 in (38 cm) in the back of the truck when additional cargo room is needed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 2. Make sure the center handle is unlocked and rotate the center handle vertically in order to release the extender side gates. 3. Fit the end of the side gate ends onto the pin and handle. Extender Position To install the bed extender into the extender position perform the following: 1. Lower the tailgate.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Rotate the handles to the horizontal position to secure into place. Locking Tab WARNING! To reduce the risk of potential injury or property damage: • Cargo must be secured. • Do not exceed cargo load rating of your vehicle. • Secure all loads to truck utilizing cargo tie downs. • Extender should not be used as cargo tie down. • When vehicle is in motion do not exceed 150 lbs (68 kg) load on the tailgate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 Bed Rail Tie-Down System CAUTION! The maximum load per cleat should not exceed 250 lbs (113 kg) and the angle of the load on each cleat should not exceed 60 degrees above horizontal, or damage to the cleat or cleat rail may occur. 3 There are two adjustable cleats on each side of the bed that can be used to assist in securing cargo.
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE out on the cleat and slide it to the detent nearest the desired location. Make sure the cleat is seated in the detent and tighten the nut. 1 — Utility Rail Detent 2 — Cleat Retainer Nut 3 — Utility Rail Cleat To remove the cleats from the utility rail, remove the end cap by pushing up on the locking tab, located on the bottom of the end cap. Slide the cleat off the end of the rail.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 SLIDE-IN CAMPERS Disconnecting the Rear Camera — If Equipped Camper Applications Certain truck models are not recommended for slide-in campers. To determine if your vehicle is excluded, please refer to the “Consumer Information Truck-Camper Loading” document available from your authorized dealer. For safety reasons, follow all instructions in this important document. 1. Open the tailgate to access the rear camera connector bracket located on the rear sill.
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Remove the connector bracket from the sill by pressing inward in the locking tab. 4. Connect the chassis plug and bracket (provided in the glove box) to the chassis wiring harness and insert the bracket back into the sill. 5. Connect the tailgate plug (provided in the glove box) to the tailgate wiring harness to ensure that the terminals do not corrode. 6. Tape the tailgate harness and bracket against the forward-facing surface of the tailgate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 NOTE: Do not carry the tailgate loose in the truck pickup box. WARNING! To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the overhanging camper compartment and be free of leaks. Locking Tang 3. Raise the right side of the tailgate until the right side pivot clears the hanger bracket. 4. Slide the entire tailgate to the right to free the left side pivot. 5.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 212 ▫ EVIC Displays . . . . . . . . . . . . . . . . . . . . . . 235 䡵 Switch Bank Button Description . . . . . . . . . . . 213 ▫ Distance To Empty (DTE) . . . . . . . . . . . . . . 239 ▫ Upper Switch Bank . . . . . . . . . . . . . . . . . . . 213 ▫ EVIC Average Fuel Economy . . . . . . . . . . . . 239 ▫ Lower Switch Bank . . . . . . . . . . . . . . . . . . . 214 ▫ Trip Functions . . . . . . . . . .
210 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 AM/FM/CD/DVD Radio (RER/REN) – If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 249 ▫ Operating Instructions — Voice Recognition System (VR) — If Equipped . . . . . . . . . . . . . 249 䡵 Sales Code RES/RSC — AM/FM Stereo Radio With CD Player (MP3 AUX Jack) And Sirius Radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 ▫ Operating Instructions — Radio Mode . . . . . 261 ▫ Operating Instructions — uconnect威 phone — If Equipped . .
UNDERSTANDING YOUR INSTRUMENT PANEL 211 ▫ Selecting uconnect威 studios (Satellite) Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 ▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . 274 ▫ Reception Quality . . . . . . . . . . . . . . . . . . . . 274 ▫ Operating Instructions - uconnect威 studios (Satellite) Mode . . . . . . . . . . . . . . . . . . . . . 275 ▫ Operating Instructions - uconnect威 phone (If Equipped) . . . . . . . . . . . . . . . . . . . . . . .
212 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 2 3 4 5 6 - Headlight Switch Instrument Cluster Radio Upper Switch Bank Upper Glove Compartment Lower Glove Compartment 7 - 115v Power Inverter Outlet 8 - Power Outlet 9 - Lower Switch Bank 10 - Cup Holders 11 - Climate Controls 12 - Power Outlet/Cigar Lighter 13 14 15 16 - Transfer Case Position Switch Ignition Switch Hood Release Parking Brake Release
UNDERSTANDING YOUR INSTRUMENT PANEL 213 SWITCH BANK BUTTON DESCRIPTION Upper Switch Bank The upper switch bank is located on the center of the instrument panel. 1. TOW/HAUL Refer to Section 5 for more information. 2. ESP OFF Refer to Section 5 for more information. 3. HAZARD WARNING FLASHER Refer to Section 6 for more information. 4. 115V POWER INVERTER Refer to Section 3 for more information. 5. REAR PARK ASSIST Refer to Section 3 for more information.
214 UNDERSTANDING YOUR INSTRUMENT PANEL Lower Switch Bank The lower switch bank is located on the center of the instrument panel. 1. HEATED SEAT Refer to Section 3 for more information. 2. VENTILATED SEAT Refer to Section 3 for more information. 3. HEATED STEERING WHEEL Refer to Section 3 for more information. 4. VENTILATED SEAT Refer to Section 3 for more information. 5. HEATED SEAT Refer to Section 3 for more information.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 INSTRUMENT CLUSTER – BASE 4
216 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER – PREMIUM
UNDERSTANDING YOUR INSTRUMENT PANEL 217 INSTRUMENT CLUSTER DESCRIPTION 1. Tachometer The Tachometer indicates engine speed in revolutions per minute. CAUTION! Do not operate the engine with the tachometer pointer at high rpm for extended periods. Engine damage may occur. 2. Turn Signal Indicators The arrow will flash with the exterior turn signal when the turn signal lever is operated. NOTE: • A continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on.
218 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! WARNING! Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H” and you hear continuous chimes, turn the engine off immediately, and call an authorized dealership for service. A hot engine cooling system is dangerous.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 rotate at the same speed. Low range provides a greater gear reduction ratio to provide increased torque at the wheels. For vehicles equipped with a premium cluster this indicator will display in the Electronic Vehicle Information Center (EVIC). Refer to ”Electronic Vehicle Information Center (EVIC) — If Equipped” in this section for more information. 7.
220 UNDERSTANDING YOUR INSTRUMENT PANEL 8. 4WD Indicator This light indicates the vehicle is in four-wheel drive and 4LOCK. 4WD allows all four wheels to receive torque from the engine simultaneously. 9. 4WD Auto Indicator The 4WD auto indicator will be illuminated whenever the four-wheel drive mode is automatically engaged. 10. SERV (Service) 4WD The SERV 4WD light monitors the electric shift four-wheel drive system.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 13. Vehicle Security Light — If Equipped This light will flash at a fast rate for approximately 15 seconds, when the vehicle security alarm is arming, and then will flash slowly until the vehicle is disarmed. 16. Odometer / Electronic Vehicle Information Center (EVIC) Display 14. Oil Pressure Gauge The pointer should always indicate some oil pressure when the engine is running.
222 UNDERSTANDING YOUR INSTRUMENT PANEL When the appropriate conditions exist, the following messages will display: display the engine hour value. The engine hours will be displayed for a period of 30 seconds until the ignition is turned OFF or the engine is started. CHAngE OIL . . . . . . . . . . . . . . . Oil Change Required door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door Ajar ESPOFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . ESP Off gASCAP . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 223 change indicator system is duty cycle-based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON position. To turn off the message temporarily, press and release the Trip Odometer button on the instrument cluster.
224 UNDERSTANDING YOUR INSTRUMENT PANEL Center (EVIC). Refer to ”Electronic Vehicle Information Center (EVIC) — If Equipped” in this section for more information. 18. Shift Lever Indicator This display indicator shows the automatic transmission shift lever selection. NOTE: In vehicles with 4.7L or 5.7L engines, the highest available transmission gear is displayed in the lower right corner of the Electronic Vehicle Information Center (EVIC) whenever the Electronic Range Select (ERS) feature is active.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 NOTE: • If the gauge pointer moves to either extreme of the gauge, the “Check Gauges” indicator will illuminate and a single chime will sound. • The voltmeter may show a gauge fluctuation at various engine temperatures. This cycling operation is caused by the post-heat cycle of the intake manifold heater system. The number of cycles and the length of the cycling operation is controlled by the engine control module.
226 UNDERSTANDING YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking capacity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 24. Oil Pressure Warning Light This light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible.
228 UNDERSTANDING YOUR INSTRUMENT PANEL Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
230 UNDERSTANDING YOUR INSTRUMENT PANEL Although your vehicle will usually be drivable and not need towing, see your authorized dealer for service as soon as possible. 28. Front Fog Light Indicator — If Equipped This light indicates when the front fog lights are ON. CAUTION! 29. Anti-Lock Brake (ABS) Light This light monitors the Anti-lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 231 30. Transmission Temperature Light This light indicates that there is excessive transmission fluid temperature that might occur with severe usage such as trailer towing. It may also occur when operating the vehicle in a high torque converter slip condition, such as 4-wheel-drive operation (e.g., snow plowing, off- road operation). If this light comes on, stop the vehicle and run the engine at idle or faster, with the transmission in NEUTRAL until the light goes off.
232 UNDERSTANDING YOUR INSTRUMENT PANEL For vehicles equipped with a premium cluster this indicator will display in the Electronic Vehicle Information Center (EVIC). Refer to ”Electronic Vehicle Information Center (EVIC) — If Equipped” in this section for more information. For vehicles equipped with a premium cluster this indicator will display in the Electronic Vehicle Information Center (EVIC). Refer to ”Electronic Vehicle Information Center (EVIC) — If Equipped” in this section for more information.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the instrument cluster. NOTE: The compass on your vehicle is self-calibrating, eliminating the need to manually calibrate the compass. This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel.
234 UNDERSTANDING YOUR INSTRUMENT PANEL • Audio Modes display Steering wheel EVIC control button, as it appears on the left side of the steering wheel. Press and release the UP button to scroll upward through the main menus (DTE, mi/gal, System Info, Messages, Units, Setup) and sub menus. Press and release the DOWN button to scroll downward through the main menus and sub menus. Steering wheel EVIC control button as it appears on the right side of the steering wheel.
UNDERSTANDING YOUR INSTRUMENT PANEL 235 EVIC Displays When the appropriate conditions exist, the EVIC displays the following messages: • Door(s) Ajar (with a single chime, if vehicle is in motion) • Hood Ajar (if equipped with hood switch) • Turn Signal On • RKE Battery Low • LOW WASHER FLUID • Oil Change Required • Left Front Turn Signal Light Out • Left Rear Turn Signal Light Out • Right Front Turn Signal Light Out • Right Rear Turn Signal Light Out • Park Assist Disabled • Service Park Assist System •
236 UNDERSTANDING YOUR INSTRUMENT PANEL Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood. • Charging System Light This light shows the status of the electrical charging system. The light should come on when the ignition switch is first turned ON and remain on briefly as a bulb check.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 • Engine Temperature Warning Light This light warns of an overheated engine condition. As temperatures rise and the gauge approaches H, this indicator will illuminate and a single chime will sound after reaching a set threshold. Further overheating will cause the temperature gauge to pass H, the indicator will continuously flash and a continuous chime will occur until the engine is allowed to cool.
238 UNDERSTANDING YOUR INSTRUMENT PANEL cycles and the vehicle has been driven several miles at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible. • Transmission Temperature Light This light indicates that there is excessive transmission fluid temperature that might occur with severe usage such as trailer towing. It may also occur when operating the vehicle in a high torque converter slip condition, such as 4-wheel-drive operation (e.g., snow plowing, off- road operation).
UNDERSTANDING YOUR INSTRUMENT PANEL 239 NOTE: If the indicator message illuminates when you start the engine, the oil change indicator system did not reset. If necessary, repeat these steps. Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. DTE cannot be reset through the RETURN button.
240 UNDERSTANDING YOUR INSTRUMENT PANEL Press the ODOMETER/TRIP ODOMETER button to cycle through all the Trip Computer functions. The Trip Functions mode displays the following information. • Trip A Shows the total distance traveled for Trip A since the last reset. • Trip B Shows the total distance traveled for Trip B since the last reset. • Elapsed Time Shows the total elapsed time of travel since the last reset when the ignition switch is in the ACC position.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 • Oil Temperature Displays the actual oil temperature. • Oil Pressure Displays the actual oil pressure. • Trans Temperature Displays the actual transmission temperature. • Engine Hours Displays the hours of engine operation. Compass Display The compass readings indicate the direction the vehicle is facing. Press and release the compass button to display one of eight compass readings and the outside temperature.
242 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Press the DOWN button until “Calibrate Compass” is displayed in the EVIC. 4. Press and release the SELECT button to start the calibration. The “CAL” indicator will be displayed in the EVIC. NOTE: Keep magnetic materials away from the top of the instrument panel, such as iPod’s, Cell Phones, Laptops and Radar Detectors. This is where the compass module is located, and it can cause interference with the compass sensor, and it may give false readings. 5.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 2. Press the UP or DOWN button until the Setup (Customer-Programmable Features) menu is reached, then press the SELECT button. 3. Press the DOWN button until the “Compass Variance” message is displayed in the EVIC, then press the SELECT button. The last variance zone number displays in the EVIC. 4. Press and release the SELECT button until the proper variance zone is selected, according to the map. 5. Press and release the RETURN button to exit.
244 UNDERSTANDING YOUR INSTRUMENT PANEL route, mile by mile, turn-by-turn until the final destination is reached. To make your selection, press and release the SELECT button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed, showing the system has been deactivated. Auto Lock Doors When this feature is selected, all doors will lock automatically when the vehicle reaches a speed of 15 mph (24 km/h).
UNDERSTANDING YOUR INSTRUMENT PANEL 245 RKE Linked To Memory When this feature is selected the memory seat, mirror, and radio settings will return to the memory set position when the Remote Keyless Entry (RKE) transmitter UNLOCK button is pressed. If this feature is not selected then the memory seat, mirror, and radio settings can only return to the memory set position using the door mounted switch.
246 UNDERSTANDING YOUR INSTRUMENT PANEL button until a check-mark appears next to the feature showing the system has been activated or the check-mark is removed, showing the system has been deactivated. Headlamp Off Delay When this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle. To make your selection, press and release the SELECT button until 0, 30, 60, or 90 appears.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 Hill Start Assist (HSA) When on is selected, the HSA system is active. Refer to “HSA (Hill Start Assistance)” under “Electronic Brake Control System” in Section 5 of this manual for system function and operating information. To make your selection, press and release the SELECT button until a checkmark appears next to the feature showing the system has been activated or the check-mark is removed, showing the system has been deactivated.
248 UNDERSTANDING YOUR INSTRUMENT PANEL Remote Start Comfort Sys. When this feature is selected and the remote start is activated, the heated steering wheel and driver heated seat features will automatically turn on in cold weather. In warm weather, the driver vented seat feature will automatically turn on when the remote start is activated. These features will stay on through the duration of remote start or until the key is turned to RUN.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side Tune/ Audio control. 3. After the hours are adjusted, press the right side Tune/Audio control to set the minutes. 4. Adjust the minutes using the right side Tune/Audio control. 5. To exit, press any button/knob or wait approximately five seconds.
250 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — uconnect姞 phone — If Equipped Refer to “uconnect威 phone” in Section 3. Clock Setting Procedure uconnect威 gps — RER only The GPS receiver used in this system is synchronized to the time data being transmitted by the GPS satellite. The satellite clock is Greenwich Mean Time (GMT). This is the worldwide standard for time. This makes the system’s clock very accurate once the appropriate time zone and daylight savings information is set.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “Daylight Savings.” Touch the screen where the words “Daylight Savings” are displayed to change the current setting. Show Time if Radio is Off When selected, this feature will display the time of day on the touch screen when the radio is turned off.
252 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RES — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. TIME Button Press the TIME button to alternate locations of the time and frequency display. Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the right side TUNE/ SCROLL control knob. 3.
254 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the mid-range tones. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones. Push the rotary TUNE/SCROLL control knob a fourth time and BALANCE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 These buttons tune the radio to the stations that you commit to pushbutton memory (12 AM and 12 FM stations).
256 UNDERSTANDING YOUR INSTRUMENT PANEL If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. CAUTION! • This CD player will accept 4-3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD and MP3 modes. TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display. RW/FF Press and hold the FF (Fast Forward) button and the CD player will begin to fast forward until FF is released, or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner.
258 UNDERSTANDING YOUR INSTRUMENT PANEL Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file normally. UDF and Apple HFS formats are not supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
260 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL 261 SALES CODE RES/RSC — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) AND SIRIUS RADIO NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
262 UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. Voice Recognition System (Radio) — If Equipped Refer to “Voice Recognition System (VR)” in Section 3. Voice Recognition Button uconnect威 phone — If Equipped Press this button to operate the uconnect威 phone feature (if equipped).
UNDERSTANDING YOUR INSTRUMENT PANEL 263 5. To exit, press any button/knob or wait five seconds. The clock can also be set by pressing the SETUP button. For vehicles equipped with satellite radio, press the SETUP button, use the TUNE/SCROLL control to select SET CLOCK, and then follow the above procedure, starting at Step 2. For vehicles not equipped with satellite radio, press the SETUP button and then follow the above procedure, starting at Step 2.
264 UNDERSTANDING YOUR INSTRUMENT PANEL SCROLL control knob to the right or left to adjust the sound level from the right or left side speakers. Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary TUNE/SCROLL control knob again to exit setting tone, balance, and fade.
UNDERSTANDING YOUR INSTRUMENT PANEL 265 Program Type Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 16-Digit Character Display Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R&B Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name.
266 UNDERSTANDING YOUR INSTRUMENT PANEL SET/RND Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND button. The symbol SET 1 will now show in the display window. Select the button (1 to 6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the SET/RND button, the station will continue to play but will not be stored into pushbutton memory.
UNDERSTANDING YOUR INSTRUMENT PANEL 267 Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD player and the CD icon will illuminate on the radio display. If a CD does not go into the slot more than 1.0 in (2.5 cm), a disc may already be loaded and must be ejected before a new disc can be loaded.
268 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Ejecting with the ignition OFF is not allowed on convertible or soft-top models (if equipped). AM/FM Button Press the button to select either AM or FM mode. SEEK Button Press the right SEEK button for the next selection on the CD. Press the left SEEK button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection.
UNDERSTANDING YOUR INSTRUMENT PANEL 269 Supported Media (Disc Types) The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file normally.
270 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
272 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack which allows the user to plug in a portable device such as an MP3 player or cassette player and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the AUX button will change the mode to auxiliary device if the AUX jack is connected.
UNDERSTANDING YOUR INSTRUMENT PANEL 273 sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios. NOTE: Sirius service is not available in Hawaii and has limited coverage in Alaska. System Activation Sirius Satellite Radio service is pre-activated, and you may begin listening immediately to the one year of audio service that is included with the factory-installed satellite radio system in your vehicle.
274 UNDERSTANDING YOUR INSTRUMENT PANEL ESN/SID Access With REN/RER Radios While in SAT mode, press the MENU button on the radio faceplate. Reception Quality Satellite reception may be interrupted due to one of the following reasons: Next, touch the SUBSCRIPTION tab on the touch screen. All the ESNs that apply to your vehicle will display. • The vehicle is parked in an underground parking structure or under a physical obstacle.
UNDERSTANDING YOUR INSTRUMENT PANEL 275 Operating Instructions - uconnect姞 studios (Satellite) Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. SEEK Buttons Press and release the SEEK buttons to search for the next channel in Satellite mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new channel until you make another selection. Holding either button will bypass channels without stopping until you release it.
276 UNDERSTANDING YOUR INSTRUMENT PANEL MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the Tune/Scroll control knob within five seconds will allow the program format type to be selected. Toggle the MUSIC TYPE button again to select the music type. By pressing the SEEK button when the Music Type function is active, the radio will be tuned to the next channel with the same selected Music Type name.
UNDERSTANDING YOUR INSTRUMENT PANEL 277 You may add a second channel to each pushbutton by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2. This allows a total of 12 Satellite channels to be stored into pushbutton memory. The channels stored in SET 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corresponding button number will display.
278 UNDERSTANDING YOUR INSTRUMENT PANEL REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a rocker type switch with a pushbutton in the center. Pressing the top of the switch will increase the volume and pressing the bottom of the switch will decrease the volume. The button located in the center of the right hand control will switch modes to Radio or CD.
UNDERSTANDING YOUR INSTRUMENT PANEL 279 The button located in the center of the left hand control will tune to the next pre-set station that you have programmed in the radio pre-set pushbuttons. CD/DVD MAINTENANCE To keep a CD/DVD in good condition, take the following precautions: CD Player Pressing the top of the switch once will go to the next track on the CD.
280 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particular disc, it may be damaged (i.e. scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service. CLIMATE CONTROLS The Climate Control System allows you to regulate the temperature, amount, and direction of air circulating throughout the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 281 Front Blower Control There are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the OFF position. NOTE: For vehicles equipped with Remote Start, the climate controls will not function during Remote Start operation if the blower control is left in the OFF position.
282 UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control Use this control to regulate the temperature of the air inside the passenger compartment. Rotating the knob counterclockwise, from top center into the blue area of the scale, indicates cooler temperatures. Rotating the knob clockwise, into the red area, indicates warmer temperatures. Mode Control (Air Direction) Mode control allows you to choose from several patterns of air distribution.
UNDERSTANDING YOUR INSTRUMENT PANEL 283 air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions. Floor Mode Air is directed through the floor outlets with a small amount through the defrost and side window demist outlets. Mix Mode Air is directed through the floor, defrost and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat at the windshield.
284 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • If the RECIRCULATION button is pressed when the system is in Mix or Defrost mode the Recirculation LED indicator will flash three times and then turn off to indicate Recirculation mode is not allowed. • Continuous use of the Recirculation mode may make the inside air stuffy and window fogging may occur. Extended use of this mode is not recommended.
UNDERSTANDING YOUR INSTRUMENT PANEL 285 Air Conditioning Operation Push this button to engage the Air Conditioning (A/C). A light will illuminate when the A/C system is engaged. MAX A/C For maximum cooling, when MAX A/C is selected the A/C is turned on automatically and the air is recirculated. NOTE: A/C cannot be deselected when in MAX A/C position. The LED will blink three times if the A/C button is pushed.
286 UNDERSTANDING YOUR INSTRUMENT PANEL The infrared two-zone ATC system automatically maintains the interior comfort level desired by the driver and all passengers. This is accomplished by an infrared sensor, located in the forward overhead console. Based on the sensor input, the system automatically adjusts the air temperature, the airflow volume, amount of outside air recirculation and the airflow direction. This maintains a comfortable temperature even under changing conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL 287 Automatic Operation 1. Position the MODE control knob to the Auto position on the Automatic Temperature Control (ATC) Panel. 2. Position the BLOWER control knob in the Auto position on the ATC Panel. 3. Next, adjust the temperature you would like the system to maintain by adjusting the driver and front passenger temperature buttons. Once the desired temperature is displayed, the system will achieve and automatically maintain that comfort level. 4.
288 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Operation This system offers a full complement of manual override features. selected. This allows the front occupants to control the volume of air circulated in the vehicle and cancel the Auto mode. NOTE: Each of these features operate independently from each other. If any one feature is controlled manually, the temperature doors will continue to operate automatically.
UNDERSTANDING YOUR INSTRUMENT PANEL 289 Floor Mode Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix Mode Air comes from the floor, defrost and side window demist outlets. This mode works best in cold or snowy conditions. It allows you to stay comfortable while keeping the windshield clear. Defrost Mode Air comes from the windshield and side window demist outlets.
290 UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation mode should only be used temporarily. The recirculation LED will illuminate on the blower control knob when this button is selected. Push the button a second time to turn off the Recirculation mode LED and allow outside air into the vehicle. NOTE: In cold weather, use of Recirculation mode may lead to excessive window fogging. The Recirculation mode is not allowed in the Floor, Mix and Defrost modes to improve window clearing operation.
UNDERSTANDING YOUR INSTRUMENT PANEL 291 Window Fogging and Frosting Vehicle windows tend to fog on the inside of the glass in mild, rainy and/or humid weather. Windows may frost on the inside of the glass in very cold weather. To clear the windows, select Defrost or Mix mode and increase the front blower speed. Do not use the Recirculation mode without A/C for long periods, as fogging may occur.
292 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 297 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 297 ▫ Automatic Transmission . . . . . . . . . . . . . . . 297 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . 298 ▫ Brake/Transmission Interlock Manual Override . . . . . . . . . . . . . . . . . . . . . . . . . . 301 ▫ 4–Speed Automatic Transmission (3.7L Engine) . . . . . . . . . . . . . . . . . . . . . . . 303 ▫ After Starting . . . . .
294 STARTING AND OPERATING ▫ NVG 246 Transfer Case Operating Information/Precautions (5 Position Switch) — If Equipped . . . . . . . . . . . . . . . . . . . . . . 320 ▫ Shifting Procedure . . . . . . . . . . . . . . . . . . . 325 䡵 Limited-Slip Differential – If Equipped . . . . . . 327 䡵 Driving On Slippery Surfaces . . . . . . . . . . . . . 328 䡵 Driving Through Water . . . . . . . . . . . . . . . . . 328 ▫ Flowing/Rising Water . . . . . . . . . . . . . . . . . 328 ▫ Shallow Standing Water . . . . . . .
STARTING AND OPERATING 295 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . 356 䡵 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 366 ▫ Tire Inflation Pressures . . . . . . . . . . . . . . . . 358 䡵 Tire Rotation Recommendations . . . . . . . . . . . 367 ▫ Tire Pressures For High Speed Operation . . . 359 䡵 Tire Pressure Monitor System (TPMS) . . . . . . . 368 ▫ Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . 360 ▫ Tire Pressure Monitor System Components . .
296 STARTING AND OPERATING 䡵 Flexible Fuel (4.7L Engine Only) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 378 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 385 ▫ Common Towing Definitions . . . . . . . . . . . . 385 ▫ E-85 General Information . . . . . . . . . . . . . . . 378 ▫ Trailer Hitch Classification . . . . . . . . . . . . . . 390 ▫ Ethanol Fuel (E-85) . . . . . . . . . . . . . . . . . . . 379 ▫ Trailer Towing Weights (Maximum Trailer Weight Ratings) . .
STARTING AND OPERATING 297 STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. The starter should not be operated for more than 15second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. WARNING! • Accidents can be caused by inadvertently moving the shift lever or by pressing the accelerator pedal.
298 STARTING AND OPERATING Tip Start Feature Do not press the accelerator. Turn the ignition key briefly to the START position and release it. The starter motor will continue to run but will automatically disengage when the engine is running. If Engine Fails To Start If the engine fails to start after you have followed the “Normal Starting” procedure, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine.
STARTING AND OPERATING 299 If the engine has been flooded, it may start to run, but not have enough power to continue running when the key is released. If this occurs, continue cranking with the accelerator pedal pushed all the way to the floor. Release the accelerator pedal and the key once the engine is running smoothly. If the engine shows no sign of starting after two 15second periods of cranking with the accelerator pedal held to the floor, the normal starting procedure should be repeated.
300 STARTING AND OPERATING WARNING! CAUTION! (Continued) Remember to disconnect the cord before driving. Damage to the 110-115 volt electrical cord could cause electrocution. AUTOMATIC TRANSMISSION • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly on the brake pedal.
STARTING AND OPERATING 301 Brake/Transmission Shift Interlock System This vehicle is equipped with a Brake Transmission Shift Interlock (BTSI) system that holds the shift lever in the PARK position when the ignition switch is in the LOCK position. To move the shift lever out of the PARK position, the ignition switch must be turned to the ON position (engine not running) and the brake pedal must be depressed.
302 STARTING AND OPERATING standard sized screwdriver or similar tool. While pressing the override tab, move the shift lever out of the PARK position. Center Console Shifter There is an override for the BTSI that allows you to move the shift lever out of the PARK position if an electrical system malfunction occurs (i.e., dead battery). To access the override (using a flat-bladed screwdriver), carefully remove the override cover which is located on the right of the shift lever gate.
STARTING AND OPERATING 303 4–Speed Automatic Transmission (3.7L Engine) NOTE: Under extremely cold temperatures (-6°F (-21°C) and when in DRIVE, transmission operation may be briefly limited to only second gear operation. Normal operation will resume once the transmission temperature has risen to a suitable level. Shifting from DRIVE to PARK or REVERSE should be done only after the accelerator pedal is released and the vehicle is stopped.
304 STARTING AND OPERATING REVERSE Use this range only after the vehicle has come to a complete stop. NEUTRAL Shift into NEUTRAL when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Set the parking brake if you must leave the vehicle. NOTE: Towing the vehicle, coasting, or driving for any other reason with shift lever in NEUTRAL can result in severe transmission damage.
STARTING AND OPERATING 305 Overdrive Operation The overdrive automatic transmission contains an electronically controlled fourth and fifth gear (OVERDRIVE).
306 STARTING AND OPERATING performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in TOW/HAUL mode, the transmission will shift to third gear and fourth gear will be enabled under steady cruise conditions. The TOW/HAUL light will illuminate in the instrument cluster to indicate when the switch has been activated. Pressing the switch a second time restores normal operation.
STARTING AND OPERATING 307 4. Wait approximately 10 seconds, then restart the engine. 5. Move the shift lever to the desired gear range. If the problem is no longer detected, the transmission will return to normal operation. If the problem persists, PARK, REVERSE, and NEUTRAL will continue to operate. Only second gear will operate in the DRIVE position. Have the transmission checked at your authorized dealer as soon as possible.
308 STARTING AND OPERATING into 3 (third gear), the transmission will never shift above third gear, but can shift down to 2 (second gear) or 1 (first gear), when needed. Console Shift Lever Column Shift Lever On vehicles equipped with 4.7L or 5.7L engines, use of ERS (or TOW/HAUL mode) also enables an additional underdrive gear which is not normally used during through-gear accelerations. This additional gear improves vehicle performance and cooling capability when towing a trailer on certain grades.
STARTING AND OPERATING 309 through third gear are underdrive gears, and fourth gear is direct drive. ERS fifth gear (Overdrive) is the same as the normal fourth gear. When in the DRIVE position in 1st through 4th gear, the first tap down (-), will display the ERS designation for the current gear (the transmission will not downshift).
310 STARTING AND OPERATING Gear Ranges Do not race the engine when shifting from PARK or NEUTRAL position into another gear range. PARK This gear position supplements the parking brake by locking the transmission. The engine can be started in this range. Never use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply the parking brake first, then place the selector in PARK position.
STARTING AND OPERATING 311 WARNING! (Continued) • It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.
312 STARTING AND OPERATING NOTE: If the vehicle is started in extremely cold temperatures, the transmission may not shift into Overdrive and will automatically select the most desirable gear for operation at this temperature. Normal operation will resume when the transmission fluid temperature has risen to a suitable level. If the transmission temperature gets extremely hot, the transmission will automatically select the most desirable gear for operation at this temperature.
STARTING AND OPERATING 313 Pressing the switch a second time restores normal operation. If the TOW/HAUL mode is desired, the button must be pressed each time the engine is started. TOW/HAUL Switch Shifts into Overdrive (fourth gear) are allowed during steady cruise (for improved fuel economy) and automatic closed-throttle downshifts to third gear are performed (for improved braking) when driving conditions warrant.
314 STARTING AND OPERATING cold. This is normal. Pressing the TOW/HAUL switch when the transmission is sufficiently warm will demonstrate that the transmission is able to shift into and out of overdrive. NOTE: If the vehicle has not been driven in several days, the first few seconds of operation after shifting the transmission into gear may seem sluggish. This is due to the fluid partially draining from the torque converter into the transmission.
STARTING AND OPERATING 315 • Neutral (NEUTRAL) This electronically shifted transfer case is designed to be driven in the two-wheel drive position (2WD) for normal street and highway conditions (dry, hard surfaced roads).
316 STARTING AND OPERATING left hand corner of the 4WD Control Switch. The transfer case NEUTRAL position is to be used for recreational towing only. Refer to “Recreational Towing” in this section. Transfer Case Position Indicator Lights Transfer case position indicator lights are located in the instrument cluster and indicate the current and desired transfer case selection. When you select a different transfer case position, the indicator lights will do the following: If All Shift Conditions Are Met 1.
STARTING AND OPERATING 317 WARNING! Always engage the parking brake when powering down the vehicle if the SERVICE 4WD light is illuminated. Not engaging the parking brake may allow the vehicle to roll, which may cause personal injury. NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning, as this can cause damage to driveline components.
318 STARTING AND OPERATING For additional information on the appropriate use of each transfer case mode position see the information below: 2WD Rear Wheel Drive High Range - Normal street and highway driving. Dry, hard surfaced roads. 4WD LOCK Four-Wheel Drive Lock Range - Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only. 4WD LOW Four-Wheel Drive Low Range - Low speed four-wheel drive.
STARTING AND OPERATING 319 light will turn OFF, the selected position indicator light will flash until the transfer case completes the shift. When the shift is complete, the indicator light for the selected position will stop flashing and remain ON. 2WD⇔ 4WD LOCK Rotate the 4WD control switch to the desired position. Shifts between 2WD and 4WD LOCK can be done with the vehicle stopped or in motion.
320 STARTING AND OPERATING 4. After the desired position indicator light is ON (not flashing), shift the transmission back into gear. Alternate Procedure 1. Bring the vehicle to a complete stop. 2. With the key ON and the engine either OFF or running, shift the transmission into NEUTRAL. 3. Rotate the transfer case control switch to the desired position. 4. After the desired position indicator light is ON (not flashing), shift the transmission back into gear.
STARTING AND OPERATING 321 • Four-wheel drive low range (4WD LOW) • Neutral (NEUTRAL) This electronically shifted transfer case is designed to be driven in the two–wheel drive position (2WD) or fourwheel drive position (4WD AUTO) for normal street and highway conditions (dry hard surfaced roads). Driving the vehicle in 2WD will have greater fuel economy benefits as the front axle is not engaged in 2WD.
322 STARTING AND OPERATING the front and rear driveshafts together and force the front and rear wheels to rotate at the same speed. This is accomplished by rotating the 4WD Control Switch to the desired position. Refer to “Shifting Procedure” for specific shifting instructions. The 4WD LOCK and 4WD LOW positions are designed for loose, slippery road surfaces only. Driving in the 4WD LOCK and 4WD LOW positions on dry hard surfaced roads may cause increased tire wear and damage to the driveline components.
STARTING AND OPERATING 323 If One or More Shift Conditions are not Met 1. The indicator light for the current position will remain ON. 2. The newly selected position indicator light will continue to flash. 3. The transfer case will not shift. NOTE: Before retrying a selection, make certain that all the necessary requirements for selecting a new transfer case position have been met. To retry the selection, turn the control knob back to the current position, wait five seconds, and retry selection.
324 STARTING AND OPERATING Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the transfer case. Because four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road conditions permit.
STARTING AND OPERATING 325 4WD LOW Four-Wheel Drive Low Range - Low speed four-wheel drive. Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). N Neutral - Disengages both the front and rear driveshafts from the powertrain. To be used for flat towing behind another vehicle. Refer to “Recreational Towing” in this section.
326 STARTING AND OPERATING stopped, the ignition key must be in the ON position with the engine either running or off. This shift cannot be completed if the key is in the accessory position. 2WD or 4WD AUTO or 4WD LOCK ⇔ 4WD LOW NOTE: When shifting into or out of 4WD LOW some gear noise may be heard. This noise is normal and is not detrimental to the vehicle or occupants. Shifting can be performed with the vehicle rolling 2 to 3 mph (3 to 5 km/h) or completely stopped.
STARTING AND OPERATING 327 NOTE: The ignition key must be ON for a shift to take place and for the position indicator lights to be operable. If the key is not ON then the shift will not take place and no position indicator lights will be on or flashing.
328 STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observed: 1. Slow down during rainstorms or when roads are slushy. 2. Slow down if the road has standing water or puddles. 3.
STARTING AND OPERATING 329 Shallow Standing Water Although your vehicle is capable of driving through shallow standing water, consider the following Caution and Warning before doing so. CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle.
330 STARTING AND OPERATING WARNING! • Driving through standing water limits your vehicle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes.
STARTING AND OPERATING 331 NOTE: After off-road usage, particularly in sand or mud, inspect the underside of the vehicle for accumulated dirt at the propeller shaft, axles, U-joints, brake rotors and calipers. Use a hose to clean off any accumulation of dirt or mud. Check the exhaust system and all exposed components for any sign of damage. If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for impacted material.
332 STARTING AND OPERATING WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer. No chemical flushes should be used in any power steering system; only the approved lubricant may be used.
STARTING AND OPERATING 333 PARKING BRAKE The foot-operated parking brake is positioned below the lower left corner of the instrument panel. To release the parking brake, pull the parking brake release handle. NOTE: The instrument cluster red brake warning light will come on and flash to indicate that the parking brake is applied. You must be sure that the parking brake is fully applied before leaving the vehicle.
334 STARTING AND OPERATING WARNING! • Always fully apply the parking brake when leaving your vehicle or it may roll and cause damage or injury. Also be certain to leave the transmission in PARK. Failure to do so may allow the vehicle to roll and cause damage or injury. • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition.
STARTING AND OPERATING 335 Four-Wheel Anti-Lock Brake System The Four-Wheel Anti-Lock Brake System (ABS) is designed to aid the driver in maintaining vehicle control under adverse braking conditions. The system operates with a separate computer to modulate hydraulic pressure to prevent wheel lockup and help avoid skidding on slippery surfaces. The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure. The pump motor makes a low humming noise during operation. This is normal.
336 STARTING AND OPERATING WARNING! WARNING! (Continued) • Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
STARTING AND OPERATING 337 ABS (Anti-Lock Brake System) The ABS aids the driver in maintaining vehicle control under adverse braking conditions. The system controls hydraulic brake pressure to prevent wheel lockup and help avoid skidding on slippery surfaces during braking. For more information about ABS, refer to “Brake System” in this section. NOTE: ABS improves steering control of the vehicle during hard braking maneuvers.
338 STARTING AND OPERATING spinning faster than the other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not spinning. This feature remains active even if TCS and ESP are in the “Partial Off” mode. Refer to “ESP (Electronic Stability Program)” in this section of this manual. This brake pressure modulation transfers drive torque from slipping to non-slipping wheels to provide optimal forward traction.
STARTING AND OPERATING 339 WARNING! (Continued) • The capabilities of a BAS-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others. HSA (Hill Start Assist) The HSA system is designed to assist the driver in launching a vehicle on an incline. HSA will maintain the level of brake pressure the driver inputs for a short duration once the driver takes his foot off of the brake pedal.
340 STARTING AND OPERATING WARNING! There may be situations on minor hills (i.e., less than 7%), with a loaded vehicle or while pulling a trailer where the system will not activate and slight rolling may occur, which could cause a collision with another vehicle or object. Always remember the driver is responsible for braking the vehicle. The system will only work if the intended direction of the vehicle and vehicle gear match.
STARTING AND OPERATING 341 WARNING! WARNING! (Continued) • If you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision with another vehicle or object behind you.
342 STARTING AND OPERATING 3. With the engine running, the brake applied, and the clutch out, rotate the steering wheel 180° counterclockwise from center. 4. Press the ESP OFF switch four times within twenty seconds. The “ESP/TCS Indicator Light” should appear and disappear four times. 5. Rotate the steering wheel 360° clockwise (180° clockwise from center). 6. Cycle ignition switch OFF then ON. 7.
STARTING AND OPERATING 343 • Oversteer - when the vehicle is turning more than appropriate for the steering wheel position. • Understeer - when the vehicle is turning less than appropriate for the steering wheel position. ESP OFF Switch ESP uses sensors in the vehicle to determine the vehicle path intended by the driver and compares it to the actual path of the vehicle.
344 STARTING AND OPERATING WARNING! • ESP cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. • ESP cannot prevent accidents, including those resulting from excessive speed in turns, driving on slippery surfaces or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING 345 ESP Partial Off This mode is entered by momentarily depressing the ESP OFF switch. When in ⬙Partial Off⬙ mode, the TCS portion of ESP, except for the “limited slip” feature described in the TCS section, has been disabled and the ⬙ESP/TCS Indicator Light⬙ will be illuminated. All other stability features of ESP function normally.
346 STARTING AND OPERATING holding the ESP OFF switch for five seconds when the vehicle is stopped and the engine is running. After five seconds, the “ESP/TCS Indicator Light” will illuminate and the “ESP Off” message will appear in the odometer. Press and release the trip odometer button located on the instrument cluster to clear this message. off-road driving but ESP function returns to provide the stability feature at speeds above 40 mph (64 km/h).
STARTING AND OPERATING 347 WARNING! With the ESP switched off, the enhanced vehicle stability offered by ESP is unavailable. In an emergency evasive maneuver the ESP system will not engage to assist in maintaining stability. “ESP Off” mode is intended for off-highway or off-road use only. ESP/BAS Warning Lamp and ESP/TCS Indicator Light The malfunction indicator for the ESP is combined with the BAS indicator.
348 STARTING AND OPERATING TSC (Trailer Sway Control) The TSC system uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appropriate actions to attempt to stop the sway. The system may reduce engine power and apply the brake of the appropriate wheel(s) to counteract the sway of the trailer. TSC will become active automatically once an excessively swaying trailer is recognized. No driver action is required. Note that TSC cannot stop all trailers from swaying.
STARTING AND OPERATING 349 TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
350 STARTING AND OPERATING Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation. Example: T145/80D18 103M. Tire Sizing Chart • High flotation tire sizing is based on U.S. design standards and it begins with the tire diameter molded into the sidewall. Example: 31x10.5 R15 LT. EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....
STARTING AND OPERATING 351 EXAMPLE: R = Construction code — ⬙R⬙ means radial construction —⬙D⬙ means diagonal or bias construction 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved unde
352 STARTING AND OPERATING EXAMPLE: Load Identification: ⴖ....blank....
STARTING AND OPERATING 353 EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation — This symbol certifies that the tire is in compliance with the U.S.
354 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires.
STARTING AND OPERATING 355 axles must not be exceeded. For further information on GAWRs, vehicle loading, and trailer towing, refer to “Vehicle Loading” in this section. To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard.
356 STARTING AND OPERATING NOTE: • The following table shows examples on how to calculate total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load carry capacity of your vehicle. • For the following example, the combined weight of occupants and cargo should never exceed 865 lbs (392 kg). WARNING! Overloading of your tires is dangerous.
STARTING AND OPERATING 357 5
358 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures can cause steering problems. You could lose control of your vehicle. • Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of vehicle control. • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure.
STARTING AND OPERATING 359 CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.” Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours or driven less than 1 mile (1.6 km) after a three hour period.
360 STARTING AND OPERATING loading may be required for high-speed vehicle operation. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Do not drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
STARTING AND OPERATING 361 vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and reinstalled at the first opportunity. Do not install more than one compact spare tire/wheel on the vehicle at any given time. CAUTION! WARNING! • Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). • Temporary-use spare tires have limited tread life.
362 STARTING AND OPERATING WARNING! The limited-use spare tires are for emergency use only. Installation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than 50 mph (80 km/h). Keep it inflated to the cold tire inflation pressure listed on either your tire placard or limited-use spare tire and wheel assembly. Replace (or repair) the original tire at the first opportunity and reinstall it on your vehicle. Failure to do so could result in loss of vehicle control.
STARTING AND OPERATING 363 Many states have laws requiring tire replacement at this point. Life of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • Tire pressure 5 • Distance driven WARNING! 1 — Worn Tire 2 — New Tire These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced.
364 STARTING AND OPERATING Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manufacturer strongly recommends that you use tires equivalent to the originals in size, quality and performance when replacement is needed.
STARTING AND OPERATING 365 WARNING! (Continued) • Failure to equip your vehicle with tires having adequate speed capability can result in sudden tire failure and loss of vehicle control. TIRE CHAINS Use “Class S” chains, or other traction aids that meet SAE Type “S” specifications. NOTE: Chains must be the proper size for the vehicle as recommended by the chain manufacturer. CAUTION! CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer readings.
366 STARTING AND OPERATING CAUTION! (Continued) • Install chains as tightly as possible and then retighten after driving about 0.5 mile (0.8 km). • Do not exceed 45 mph (72 km/h). • Drive cautiously and avoid severe turns and large bumps, especially with a loaded vehicle. • Do not install tire chains on front wheels of 4x2 vehicles. • Do not drive for a prolonged period on dry pavement.
STARTING AND OPERATING 367 poorer than that of non-studded tires. Some states prohibit studded tires; therefore, local laws should be checked before using these tire types. TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates and tend to develop irregular wear patterns. These effects can be reduced by timely rotation of tires.
368 STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM (TPMS) The Tire Pressure Monitoring System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold tire inflation placard pressure. The placard pressure is defined on the Tire and Loading Information label. The Tire and Loading Information label is located on the drivers side B-pillar. The tire pressure will vary with temperature by approximately 1 psi (6.9 kPa) for every 12°F (6.5°C).
STARTING AND OPERATING 369 have been received. The vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) to receive this information. As an example, assume your vehicle has a recommended cold tire inflation placard pressure (parked for more than 3 hours) of 35 psi (241 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 30 psi (207 kPa), a temperature drop to 20°F (-7°C) will decrease the tire pressure to approximately 26 psi (179 kPa).
370 STARTING AND OPERATING NOTE: • The TPMS is not intended to replace normal tire care and maintenance, nor to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. • Driving on a significantly underinflated tire causes the tire to overheat and can lead to tire failure. Underinflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
STARTING AND OPERATING 371 Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Lamp will illuminate in the instrument cluster, and an audible chime will be activated when one or more of the four active road tire pressures are low. Should this occur, you should stop as soon as possible, check the inflation pressure of each tire on your vehicle and inflate each tire to the vehicle’s recommended cold placard pressure value.
372 STARTING AND OPERATING 1. This spare tire does not have a tire pressure monitoring sensor. Therefore, the TPMS will not monitor the tire pressure in the spare tire. 2. If you install the full size spare tire in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition key cycle, a chime will sound and the TPM Telltale Light will still turn ON due to the low tire. 3.
STARTING AND OPERATING 373 FUEL REQUIREMENTS All engines are designed to meet all emissions regulations and provide excellent fuel economy and performance when using high quality unleaded “regular” gasoline having an octane rating of 87. The use of premium gasoline is not recommended, as it will not provide any benefit over regular gasoline in these engines. The 5.
374 STARTING AND OPERATING Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasolines contain oxygenates and are specifically blended to reduce vehicle emissions and improve air quality. The manufacturer supports the use of reformulated gasolines. Properly blended reformulated gasolines will provide excellent performance and durability for the engine and fuel system components.
STARTING AND OPERATING 375 If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, the engine will have some or all of these symptoms: More extensive repairs will be required for prolonged exposure to E-85 fuel. • operate in a lean mode MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT.
376 STARTING AND OPERATING Materials Added To Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in unnecessary cost. Therefore, you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law.
STARTING AND OPERATING 377 NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: (Continued) WARNING! (Continued) • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill.
378 STARTING AND OPERATING WARNING! (Continued) • Keep the trunk/liftgate/swing gate closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle. CAUTION! Only vehicles with the yellow E-85 fuel filler cap (gas cap) can operate on E-85. FLEXIBLE FUEL (4.7L ENGINE ONLY) — IF EQUIPPED E-85 General Information The information in this section is for Flexible Fuel vehicles only.
STARTING AND OPERATING 379 ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame.
380 STARTING AND OPERATING NOTE: When the ambient temperature is above 90°F (32°C), you may experience hard starting and rough idle following start up even if the above recommendations are followed. Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) and Gasoline Vehicles FFV vehicles operated on E-85 require specially formulated engine oils. These special requirements are included in MOPAR威 engine oils, and in equivalent oils meeting Chrysler Specification MS-6395.
STARTING AND OPERATING 381 Replacement Parts Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol, compatible parts. CAUTION! Replacing fuel system components with non-ethanol compatible components can damage your vehicle. ADDING FUEL The gas cap is located behind the fuel filler door, on the left side of the vehicle. Open the fuel door and remove the fuel cap by turning it counter-clockwise.
382 STARTING AND OPERATING WARNING! (Continued) • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. After removing the dispensing nozzle, tighten the gas cap 1⁄4 turn until one click is heard/felt. This is an indication that the cap is properly tightened. Be sure the gas cap is tightened every time the vehicle is refueled.
STARTING AND OPERATING 383 VEHICLE LOADING Certification Label As required by National Highway Traffic Safety Administration regulations, your vehicle has a certification label affixed to the driver’s side door or pillar. This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Rating (GAWR) front and rear, and Vehicle Identification Number (VIN). A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture.
384 STARTING AND OPERATING Rim Size This is the rim size that is appropriate for the tire size listed. Inflation Pressure This is the cold tire inflation pressure for your vehicle for all loading conditions up to full GAWR. Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle.
STARTING AND OPERATING 385 CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also overloading can shorten the life of your vehicle. TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.
386 STARTING AND OPERATING Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination. (Note that GCWR ratings include a 150 lbs (68 kg) allowance for the presence of a driver). Tongue Weight (TW) The tongue weight is the downward force exerted on the hitch ball by the trailer. In most cases it should not be less than 10% or more than 15% of the trailer load. You must consider this as part of the load on your vehicle.
STARTING AND OPERATING 387 Weight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the truck. These kind of hitches are the most popular on the market today and they’re commonly used to tow small- and medium-sized trailers. Weight-Distributing Hitch A weight-distributing system works by applying leverage through spring (load) bars.
388 STARTING AND OPERATING WARNING! • An improperly adjusted weight distributing hitch system may reduce handling, stability and braking performance and could result in an accident. • Weight distributing systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.
STARTING AND OPERATING 389 5 EXAMPLE — With Weight-Distributing Hitch (Correct) EXAMPLE — Improper Adjustment of WeightDistributing Hitch (Incorrect) Fifth-Wheel Hitch The fifth-wheel hitch is a special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed. It connects a vehicle and fifth-wheel trailer with a coupling king pin.
390 STARTING AND OPERATING Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck. The coupling arm connects to the hitch mounted over the rear axle in the truck bed. Trailer Hitch Classification The rear bumper is intended to tow trailers up to 5,000 lbs (2 268 kg) without added equipment or alterations to the standard equipment.
STARTING AND OPERATING 391 All trailer hitches should be professionally installed on your vehicle. Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. Trailer Towing Weights (Maximum Trailer Weight Ratings) NOTE: For additional trailer towing information (maximum trailer weight ratings) refer to the following website addresses: • http:// www.dodge.com/towing. 5 • http:// www.dodge.ca (Canada).
392 STARTING AND OPERATING • The weight of any other type of cargo or equipment put in or on your vehicle • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information Placard under “Tire Safety Information” in this section.
STARTING AND OPERATING 393 WARNING! (Continued) • Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. You could lose control of your vehicle and have an accident. When hauling cargo or towing a trailer, do not overload your vehicle or trailer.
394 STARTING AND OPERATING 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). • When replacing tires, refer to “Tires–General Information” for proper tire replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s GVWR and GAWR limits.
STARTING AND OPERATING 395 CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. WARNING! Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident.
396 STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations.
STARTING AND OPERATING 397 WARNING! Any work done to the vehicle’s electrical system or wiring should be performed by a qualified automotive technician. If done improperly it may cause damage to the electrical system wiring and could result in serious or fatal injury. Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer up in an area away from heavy traffic.
398 STARTING AND OPERATING NOTE: Using “TOW/HAUL” mode or a lower gear range while operating the vehicle under heavy operating conditions will improve performance and extend transmission life by reducing excessive shifting and heat build up. This action will also provide better engine braking. The automatic transmission fluid and filter should be changed if you regularly tow a trailer for more than 45 minutes of continuous operation.
STARTING AND OPERATING 399 − Air Conditioning Turn off temporarily. CAUTION! Using this vehicle for snowplow applications can cause damage to the vehicle. SNOWPLOW NOTE: Do not use this model vehicle for snowplow applications. WARNING! Snowplows and other aftermarket equipment should not be added to the front end of your vehicle. The airbag crash sensors may be affected by the change in the front end structure.
400 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Recreational Towing – 4-Wheel Drive Models CAUTION! CAUTION! Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing. Recreational Towing – 2-Wheel Drive Models Recreational towing of 2-Wheel Drive models is not allowed. Towing with the rear wheels on the ground can result in severe transmission damage.
STARTING AND OPERATING 401 Recreational Towing Procedure — Electronic Shift Transfer Case — If Equipped Use the following procedure to prepare your vehicle for recreational towing: CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in NEUTRAL before recreational towing to prevent damage to internal parts. 1. Bring the vehicle to a complete stop. 2. Shut OFF the engine. 3. Turn the ignition key to the ON position, but do not start the engine. 4.
402 STARTING AND OPERATING 16. Release the parking brake. NOTE: • Steps 1 through 5 are requirements that must be met prior to depressing the NEUTRAL button, and must continue to be met until the four seconds elapses and the shift has been completed.
STARTING AND OPERATING 403 5. Shift the transmission into NEUTRAL. 6. Press the transfer case switch NEUTRAL button for one second. 7. After the NEUTRAL indicator light turns off, release the NEUTRAL button. 8. After the NEUTRAL button has been released, the transfer case will shift to the position identified by the selector switch. 9. Shift the transmission into PARK. NOTE: • The transfer case cannot be shifted into NEUTRAL from the 4WD AUTO (if equipped) position.
404 STARTING AND OPERATING WARNING! CAUTION! You or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake. The transfer case NEUTRAL position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move, even if the transmission is in PARK. The parking brake should always be applied when the driver is not in the vehicle.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . 406 䡵 Jump-Starting Procedures . . . . . . . . . . . . . . . . 419 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 406 ▫ With Portable Starting Unit . . . . . . . . . . . . . 421 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . 407 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 422 ▫ Removing The Spare Tire . . . . . . . . . . . . . . .
406 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning flasher switch is located on the upper switch bank just below the radio. Press the switch to turn on the Hazard Warning flashers. When the Hazard Warning flasher switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off flashers. This is an emergency warning system and should not be used when the vehicle is in motion.
WHAT TO DO IN EMERGENCIES 407 Jack Location The jack and jack tools are stored under the front passenger seat. Removal To access the jack and jack tools you must remove the plastic access cover, located on the side of the seat. To remove the cover, pull the front part of the cover (closest to the front of the seat) toward you to release a locking tab. Once the front of the cover is loose, slide the cover toward the front of the seat until it is free from the seat frame.
408 WHAT TO DO IN EMERGENCIES Remove the jack and tools by removing the wing bolt and sliding the assembly from under the seat. WARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid acceleration or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.
WHAT TO DO IN EMERGENCIES 409 Reinstalling The Jack And Tools 1. Lower the jack all the way down by turning the jack turn-screw until the jack is snug. 3. Fold the flap and roll the jack tool kit into a cylindrical package (in direction of arrows) and tie to the jack using the tie straps. 2. Position the jack and tool bag (unrolled). Make sure the lug wrench is under the jack near the jack turn-screw.
410 WHAT TO DO IN EMERGENCIES Tying Bag to Jack with Straps Jack and Tools Tied
WHAT TO DO IN EMERGENCIES 411 4. Place the jack and tools in the storage position holding the jack by the jack turn-screw, slip the jack and tools under the seat so that the bottom slot engages into the fastener on the floor, and then secure to the floor pan using the wing bolt. Reinstall the plastic cover. Jack and Tools Removing The Spare Tire Remove the spare tire before attempting to jack up the truck. Attach the wheel wrench to the jack extension tube.
412 WHAT TO DO IN EMERGENCIES NOTE: The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. Preparations 1. Park the vehicle on a firm level surface. Avoiding ice or slippery areas. WARNING! 1 — Lower 2 — Raise It is recommended that you stow the flat or spare to avoid tangling the loose cable. Do not attempt to change a tire on the side of the vehicle close to moving traffic.
WHAT TO DO IN EMERGENCIES 413 4. Turn the ignition OFF. 5. Turn on the Hazard Warning flasher. 6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked.
414 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway, be extremely careful of motor traffic. • To assure that spare tires, flat or inflated are securely stowed, spares must be stowed with the valve stem facing the ground. • Turn on the Hazard Warning flasher.
WHAT TO DO IN EMERGENCIES 415 6 4X2 Jacking Location 4X4 Jacking Location • Operate the jack using the jack drive tube and the wheel wrench. The tube extension may be used but is not required.
416 WHAT TO DO IN EMERGENCIES • For all trucks, when changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle between the wheel and the shock bracket with the drive tubes extending to the rear. • Connect the jack tube extension and wheel wrench. Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. 4.
WHAT TO DO IN EMERGENCIES 417 wheel nuts. To avoid the risk of forcing the vehicle off the jack, do not fully tighten the wheel nuts until the vehicle has been lowered. 6. Using the wheel wrench, finish tightening the wheel nuts using a crisscross pattern. Correct wheel nut tightness is 130 ft lbs (177 N·m) torque. If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station.
418 WHAT TO DO IN EMERGENCIES bolt circle, tightening the wheel nut opposite to the wheel nut just previously tightened until final torque is achieved. Recommended torques are shown in the following chart. Disc Wheels Type Nut Stud Size Torque Ft. Lbs. Cone 9/16-18 110-150 Torque Newton Meters 160-200 To Stow The Flat Or Spare NOTE: Vehicles equipped with aluminum wheels cannot be stored under the vehicle because the wheel retainer will not fit through the wheel pilot hole.
WHAT TO DO IN EMERGENCIES 419 HOISTING A conventional floor jack may be used at the jacking locations. Refer to the graphics that show jacking locations. However, a floor jack or frame hoist must never be used on any other parts or the underbody. CAUTION! Never use a floor jack directly under the differential housing of a loaded truck or damage to your vehicle may result. JUMP-STARTING PROCEDURES Do not attempt to push or tow your vehicle to get it started.
420 WHAT TO DO IN EMERGENCIES 1. Remove all metal jewelry such as watch bands or bracelets which might make an unintended electrical contact. 2. Park the booster vehicle within cable reach but without letting the vehicles touch. Set the parking brake on both vehicles, place the automatic transmission in PARK and turn the ignition OFF. 3. Turn off the heater, radio, and all unnecessary electrical loads. 4. Connect one end of a jumper cable to the positive terminal of the booster battery.
WHAT TO DO IN EMERGENCIES 421 WARNING! (Continued) • During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump-starting because the battery could rupture or explode. The battery temperature must be brought up above freezing point before attempting a jump-start. 6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 7.
422 WHAT TO DO IN EMERGENCIES CAUTION! It is very important that the starting unit operating voltage does not exceed 12-Volts DC or damage to the battery, starter motor, alternator or electrical system may occur. FREEING A STUCK VEHICLE If the vehicle becomes stuck in snow, sand or mud, it can often be moved by a rocking motion. Move the shift lever rhythmically between DRIVE and REVERSE while applying slight pressure to the accelerator.
WHAT TO DO IN EMERGENCIES 423 WARNING! (Continued) • Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. CAUTION! Tow hooks are for emergency use only to rescue a vehicle stranded off-road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. TOWING A DISABLED VEHICLE Proper towing or lifting equipment is required to prevent damage to your vehicle.
424 WHAT TO DO IN EMERGENCIES 2-Wheel Drive Vehicles Provided that the transmission is operable, tow with the transmission in NEUTRAL and the ignition key is in the OFF position along with the front wheels raised and the rear wheels on the ground. Speed must not exceed 30 mph (50 km/h) and the distance must not exceed 15 miles (25 km). CAUTION! Towing faster than 30 mph (50 km/h) or for more than 15 miles (25 km) can cause severe damage to the transmission.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment— 3.7L . . . . . . . . . . . . . . 427 䡵 Maintenance Procedures . . . . . . . . . . . . . . . . . 433 䡵 Engine Compartment— 4.7L . . . . . . . . . . . . . . 428 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 433 䡵 Engine Compartment— 5.7L . . . . . . . . . . . . . . 429 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 435 䡵 Onboard Diagnostic System (OBD II) . . . . . . . 430 ▫ Engine Air Cleaner Filter . . . . . . .
426 MAINTAINING YOUR VEHICLE ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . 440 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 466 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . 443 ▫ Dual Headlight/Front Park And Turn Signal — If Equipped . . . . . . . . . . . . . . . . . . . . . . 466 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . 448 ▫ Rear Axle And 4X4 Front Driving Axle Fluid Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 427 ENGINE COMPARTMENT— 3.
428 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT— 4.
MAINTAINING YOUR VEHICLE 429 ENGINE COMPARTMENT— 5.
430 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) Your vehicle is equipped with a sophisticated onboard diagnostic system called OBDII. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 431 appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the MIL. Resolving the problem will turn the MIL light off. EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration.
432 MAINTAINING YOUR VEHICLE 5. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn OFF the ignition or start the engine.
MAINTAINING YOUR VEHICLE 433 DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
434 MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about five minutes after a fully warmed up engine is shut off. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Always maintain the oil level within the SAFE zone on the dipstick. Adding one quart of oil when the reading is at the bottom of the SAFE zone will result in a reading at the top of the safe zone on these engines.
MAINTAINING YOUR VEHICLE 435 starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to “Engine Compartment” in this section. Lubricants which do not have both the engine oil certification mark and the correct SAE viscosity grade number should not be used.
436 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals. used to assure most efficient service. MOPAR威 engine air cleaner filters are a high quality filter and are recommended. WARNING! Maintenance-Free Battery The top of the maintenance-free battery is permanently sealed. You will never have to add water or is periodic maintenance required. The air induction system (air cleaner, hoses, etc.
MAINTAINING YOUR VEHICLE 437 WARNING! (Continued) CAUTION! • Battery gas is flammable and explosive. Keep flame or sparks away from the battery. Don’t use a booster battery or any other booster source with an output greater than 12 volts. Don’t allow cable clamps to touch each other. • Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling.
438 MAINTAINING YOUR VEHICLE include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time. WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs.
MAINTAINING YOUR VEHICLE 439 application of any lubricant, the parts concerned should be wiped clean to remove dust and grit. After lubricating, excess oil and grease should be removed. Particular attention should also be given to hood latching components to ensure proper function. When performing other underhood services, the hood latch, release mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year, preferably in the Fall and Spring.
440 MAINTAINING YOUR VEHICLE exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. directed on the container, aids cleaning action, reduces the freezing point to avoid line clogging, and is not harmful to paint or trim. The washer fluid reservoir will hold a full gallon of fluid when the Low Washer Fluid Light illuminates.
MAINTAINING YOUR VEHICLE 441 WARNING! CAUTION! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to Exhaust Gas in the Safety Tips section of this manual. Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
442 MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may indicate severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE 443 Cooling System WARNING! You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot. Coolant Checks Check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable).
444 MAINTAINING YOUR VEHICLE Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals. Selection Of Coolant Use only the manufacturer’s recommended engine coolant (antifreeze). Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. CAUTION! • Mixing of engine coolant (antifreeze) other than specified HOAT engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.
MAINTAINING YOUR VEHICLE 445 Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze). When adding engine coolant (antifreeze): • The manufacturer recommends using MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology). • Mix a minimum solution of 50% HOAT engine coolant (antifreeze) and distilled water. Use higher concentrations (not to exceed 70%) if temperatures below -34°F (-37°C) are anticipated.
446 MAINTAINING YOUR VEHICLE WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
MAINTAINING YOUR VEHICLE 447 of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment.
448 MAINTAINING YOUR VEHICLE • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean, also. • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emissions.
MAINTAINING YOUR VEHICLE 449 With disc brakes the fluid level can be expected to fall as the brake linings wear. However, an unexpected drop in fluid level may be caused by a leak and a system check should be conducted. Use only the manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. WARNING! • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire.
450 MAINTAINING YOUR VEHICLE axles. The fluid level should be 5/8 in (16 mm) below the fill hole on 9 1/4 in manufacturer’s rear axles. The MOPAR威 Limited Slip Additive should be added to the gear lubricant whenever a fluid change is made. Drain and Refill Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals. Transfer Case Lubricant Selection Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.
MAINTAINING YOUR VEHICLE 451 Automatic Transmission Selection Of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission performance. Use only the manufacturer’s recommended transmission fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid.
452 MAINTAINING YOUR VEHICLE transmission with an improper fluid level will greatly reduce the life of the transmission and of the fluid. Check the fluid level whenever the vehicle is serviced. Fluid Level Check – 42RLE/545RFE Check the fluid level while the transmission is at normal operating temperature 82°C (180°F). This occurs after at least 15 miles (25 km) of driving. At normal operating temperature the fluid cannot be held comfortably between the fingertips.
MAINTAINING YOUR VEHICLE 453 room temperature, it should be between the “HOT” (upper) reference holes when the transmission reaches 180°F (82°C). Remember it is best to check the level at the normal operating temperature. CAUTION! Be aware that if the fluid temperature is below 50°F (10°C) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. 7. Check for leaks. Release parking brake.
454 MAINTAINING YOUR VEHICLE Appearance Care and Protection from Corrosion The most common causes are: Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
MAINTAINING YOUR VEHICLE 455 • Use MOPAR威 Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • It is important that the drain holes in the lower edges of the doors, rocker panels and trunk be kept clear and open. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. • If you detect any stone chips or scratches in the paint, touch them up immediately.
456 MAINTAINING YOUR VEHICLE • Use MOPAR威 Touch Up Paint on scratches as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle. Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil and/or excessive brake dust, use MOPAR威 Wheel Cleaner (05066247AB) or equivalent or select a nonabrasive, non-acidic cleaner.
MAINTAINING YOUR VEHICLE 457 • Do not use any solvents or protectants on Stain Repel products. Interior Care Use MOPAR威 Total Clean to clean fabric upholstery and carpeting. Use MOPAR威 Total Clean to clean vinyl upholstery. MOPAR威 Total Clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth.
458 MAINTAINING YOUR VEHICLE Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOPAR威 Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear window equipped with electric defrosters or the right rear quarter window equipped with the radio antenna.
MAINTAINING YOUR VEHICLE 459 FUSES Totally Integrated Power Module The totally integrated power module (TIPM) is located in the engine compartment near the battery. This center contains cartridge fuses and mini fuses. A description of each fuse and component may be stamped on the inside cover, otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart.
460 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse J03 25 Amp Natural J04 40 Amp Green J05 30 Amp Pink J06 30 Amp Pink J07 J08 J09 25 Amp Natural 30 Amp Pink 30 Amp Pink Mini Fuse Description Bat — Passenger Door Node Bat — ABS Pump Cavity Cartridge Fuse J10 40 Amp Green J11 30 Amp Pink Mini Fuse Bat — L/Bar/OffRoad Bat — Sway/ Thatchum/Rear Doors Starter Solenoid Bat — ABS Valve J12 Bat — H/Lamp Wash/MTV/ CM2200/Elec Vac Pump Bat — Driver Door Node Bat — DTCM/Axle Locks Bat — Plg/Electric Brake J
MAINTAINING YOUR VEHICLE 461 Cavity Cartridge Mini Fuse Fuse M18 25 Amp Natural M19 5 Amp Tan M20 M21 M22 M23 M24 M25 25 Amp Natural 25 Amp Natural 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 10 Amp Red Description Ign R/ACC — Sunroof/Window Sw Illum Frt Wiper Cavity Cartridge Mini Fuse Fuse M26 10 Amp Red M27 15 Amp Blue M28 10 Amp Red Door Locks M29 Fuel Pump M30 Bat — Trlr Light/PreSafe #2 Bat — Trlr Tow BUX/ HGM Bat — J1962 Diag/ Mirrors M31 TCM/Trans Range M32 M33 15 Amp Blue 25 Amp Natural
462 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse M34 15 Amp Blue M35 20 Amp Yellow M36 20 Amp Yellow M37 10 Amp Red M38 20 Amp Yellow M39 30 Amp Green M40 25 Amp Natural M41 15 Amp Blue Description Bat — CCN/Interior Light/SCM/Sw Bank Ign R-Frt Seat/Vent Ign R-Rear Seat/Steer Wheel Horn #1 IOD-CCN/Interior Mods IOD-Amp/Radio Cavity Cartridge Mini Fuse Fuse M42 10 Amp Red M43 10 Amp Red M44 10 Amp Red M45 10 Amp Red M46 20 Amp Yellow M47 10 Amp Red Rear Wiper M48 IOD-SDARS/VES 2–3/DVD/HFM/ UG
MAINTAINING YOUR VEHICLE 463 Cavity Cartridge Mini Fuse Fuse M50 25 Amp Natural M51 20 Amp Yellow M52 10 Amp Red M53 15 Amp Blue M54 20 Amp Yellow Description ASD #1, #2 ASD #3 IGN R/S-SWAY/ TCASE/DTCM/FAD IGN R/S-MFSW/ CNN/SCM/TPM/RR View IOD — Spare CAUTION! • When installing the totally integrated power module cover, it is important to ensure the cover is properly positioned and fully latched.
464 MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you are storing your vehicle for more than 21 days, we recommend that you take the following steps to minimize the drain on your vehicle’s battery: in the fresh air and high blower setting. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. • Disconnect the Ignition-Off Draw (IOD) fuse located in the Integrated Power Module, located in the engine compartment.
MAINTAINING YOUR VEHICLE 465 REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Bulb No. Overhead Console Lights . . . . . . . . . . . . . . . TS 212-2 Dome Light. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7679 NOTE: For lighted switches, see your authorized dealer for replacement instructions. All of the inside bulbs are brass or glass-wedge base. Aluminum base bulbs are not approved. LIGHT BULBS — Exterior Bulb No. Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
466 MAINTAINING YOUR VEHICLE BULB REPLACEMENT Dual Headlight/Front Park and Turn Signal — If Equipped 1. Open the hood. 2. Disconnect the negative battery cable. 3. Remove the four grille attachment bolts. 4. Remove the grille. 5. Remove the two headlamp assembly attachment bolts. 6. Reach into the front wheel house ahead of the front wheel to unsnap and lift the cover over the access hole in the front of the wheel house splash shield. Access to the bulb retainer can be gained through the wheel liner hole.
MAINTAINING YOUR VEHICLE 467 7. Reach through the access hole to access the rear lamp retainer. Quad Headlight/Front Park and Turn Signal — If Equipped 1. Open the hood. 2. Disconnect the negative battery cable. 3. Remove the four grille attachment bolts. 4. Remove the grille. 7 8. Remove headlamp assembly. 9. Disconnect electrical connectors. 10. Replace bulb(s).
468 MAINTAINING YOUR VEHICLE 5. Remove the two headlamp assembly attachment bolts. 6. Reach into the front wheel house ahead of the front wheel to unsnap and lift the cover over the access hole in the front of the wheel house splash shield. Access to the bulb retainer can be gained through the wheel liner hole. 7. Reach through the access hole to access the rear lamp retainer. 8. Remove headlamp assembly. 9. Disconnect electrical connectors. 10. Replace bulb(s).
MAINTAINING YOUR VEHICLE 469 Fog Lights 1. Reach under the vehicle, unlock and twist the connector counterclockwise 1⁄4 turn and remove the connector and bulb from the housing. 3. Reverse the procedure for installation of bulbs and housing. 2. Pull the bulb straight from the connector.
470 MAINTAINING YOUR VEHICLE Tail, Stop, Turn and Backup Lights 1. Remove the two screws that pass through the bed sheetmetal. 2. Pull the housing straight out from the body to separate the housing from the body.
MAINTAINING YOUR VEHICLE 471 3. Rotate the bulb socket counterclockwise to remove from the housing. 4. Pull the bulb straight out of the socket. 5. Reverse the procedure to install the bulb and housing.
472 MAINTAINING YOUR VEHICLE Center High-Mounted Stoplight (CHMSL) With Cargo Light 1. Remove the two screws holding the housing/lens to the body as shown. 2. Separate the connector holding the housing and wiring harness to the body.
MAINTAINING YOUR VEHICLE 473 3. Turn the desired bulb socket 1⁄4 turn and remove the socket and bulb from housing. 4. Pull the desired bulb straight from the socket. • Outside Bulbs: Cargo Lights • Inside Bulb: Center High-Mounted Stop Light 5. Reverse the procedure for installation of bulbs and housing.
474 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel (Approximate) Regular Cab Shortbed/Crew Quad Cab Models Regular Cab Longbed/Crew Quad Cab Models (Optional) Engine Oil with Filter 3.7L Engine (SAE 5W-20, API Certified) 4.7L Engine (SAE 5W-20, API Certified) 5.7L Engine (SAE 5W-20, API Certified) Cooling System 3.7L Engine (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) 4.7L Engine (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula) 5.
MAINTAINING YOUR VEHICLE 475 FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil – 3.7L, 4.7L, and 5.7L Engines Engine Oil Filter – 3.7L Engine Engine Oil Filter – 4.7L and 5.7L Engines Spark Plugs – 3.7L Engine Spark Plugs – 4.7L Engine Spark Plugs – 5.7L Engine Fuel Selection – 3.7L and 4.7L Engines Fuel Selection – 5.
476 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Transfer Case NVG 246 Automatic Transfer Case Only Front Axle (4X4) Rear Axle Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4 Automatic Transmission Fluid MOPAR威 ATF+4 Automatic Transmission Fluid MOPAR威 PN 05179014AA, NVG 246 Automatic Transmission Fluid or equivalent. GL-5 SAE 75W-90 (MS-9763) or equivalent. MOPAR威 Synthetic Gear Lubricant SAE 75W-140 (MS-8985).
MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . 478 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 478 ▫ Required Maintenance Intervals . . . . . . . . . .
M A I N T E N A N C E 478 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 479 M NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or 6 months, whichever comes first.
M A I N T E N A N C E S C H E D U L E S 8 480 MAINTENANCE SCHEDULES • Check all lights and other electrical items for correct operation. At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines. CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle. Required Maintenance Intervals NOTE: ** Vehicle’s built with the 4.7L engine are equipped with sixteen spark plugs.
MAINTENANCE SCHEDULES 481 M 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings, replace if necessary. ❏ Inspect the CV joints.
M 482 MAINTENANCE SCHEDULES A I N 18,000 Miles (30,000 km) or T 18 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ Inspect the front and rear axle fluid, S C H E D U L E S change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter.
MAINTENANCE SCHEDULES 483 M 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule 42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings, replace if necessary.
M 484 MAINTENANCE SCHEDULES A I N 54,000 Miles (90,000 km) or T 54 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ Inspect the front and rear axle fluid, S C H E D U L E S 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires.
MAINTENANCE SCHEDULES 485 M 66,000 Miles (110,000 km) or 66 Months Maintenance Service Schedule 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary. ❏ Inspect the CV joints. ❏ Inspect exhaust system.
M 486 MAINTENANCE SCHEDULES A I N 78,000 Miles (130,000 km) or T 78 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary.
MAINTENANCE SCHEDULES 487 M 90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the top row of spark plugs (4.7L Engine). Replace the spark plugs (3.7L and 5.7L Engines). Inspect and replace PCV valve if necessary. † Inspect the transfer case fluid.
M 488 MAINTENANCE SCHEDULES A I N 102,000 Miles (170,000 km) or T 102 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ Replace the ignition cables (4.7L S C H E D U L E S Engine). ❏ Replace the side row of spark plugs (4.7L Engine). ❏ Flush and replace the engine coolant if not done at 60 months.
MAINTENANCE SCHEDULES 489 M 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the ignition cables (3.7L Engine). Replace the top row of spark plugs (4.7L Engine). Replace the spark plugs (3.7L and 5.7L Engines). Inspect the brake linings; replace if necessary. Inspect the CV joints. Inspect exhaust system.
M 490 MAINTENANCE SCHEDULES A I N 126,000 Miles (210,000 km) or T 126 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ Inspect the front and rear axle fluid, S C H E D U L E S change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
MAINTENANCE SCHEDULES 491 M 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary. ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. ❏ Inspect the CV joints.
M A I N T E N A N C E S C H E D U L E S 8 492 MAINTENANCE SCHEDULES † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! You can be badly injured working on or around a motor vehicle. Do only the service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 497 ▫ Prepare For The Appointment . . . . . . . . . . . 495 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 497 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 495 䡵 Warranty Information (U.S. Vehicles Only) . . . .
494 IF YOU NEED CONSUMER ASSISTANCE 䡵 Publication Order Forms . . . . . . . . . . . . . . . . 499 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 501 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 501 ▫ Temperature Grades . . . . . . . . . . . . . . . . . . 502 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 495 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
496 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealership. They want to know if you need assistance. • If an authorized dealership is unable to resolve the concern, you may contact the manufacturer’s customer center.
IF YOU NEED CONSUMER ASSISTANCE 497 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
498 IF YOU NEED CONSUMER ASSISTANCE the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns. WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm.
IF YOU NEED CONSUMER ASSISTANCE 499 If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.
500 IF YOU NEED CONSUMER ASSISTANCE vehicles. A complete working knowledge of the vehicle, system, and/or components is written in straightforward language with illustrations, diagrams, and charts. • Owner’s Manuals These Owner’s Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler LLC vehicles. Included are starting, operating, emergency and maintenance procedures as well as specifications, capabilities and safety tips.
IF YOU NEED CONSUMER ASSISTANCE 501 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle. All passenger car tires must conform to Federal safety requirements in addition to these grades.
502 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
504 INDEX Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 381 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . 150 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 436 Air Conditioner Maintenance . . . . . . . . . . . . . . . 437 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 280 Air Conditioning Controls . . . . . . . . . . . . . . . . . 280 Air Conditioning, Operating Tips . . . . . . . . . . . . 292 Air Conditioning Refrigerant . . . . . . . . . .
INDEX 505 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307 Special Additives . . . . . . . . . . . . . . . . . . . . . . 453 Torque Converter . . . . . . . . . . . . . . . . . . . . . . 307 Axle Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . 449,476 Axle Lubrication (Axle Fluid) . . . . . . . . . . . . . . . 449 Back-Up Camera . . . . . . . . . . . . . . . . . . . . . . . . 159 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436 Emergency Starting . .
506 INDEX Carbon Monoxide Warning . . . . . . . . . . . . 75,207,377 Cargo Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Center High Mounted Stop Light . . . . . . . . . . . . 472 Center Lap Belts . . . . . . . . . . . . . . . . . . . . . . . . . 48 Center Seat Storage Compartment . . . . . . . . . . . . 184 Certification Label . . . . . . . . . . . . . . . . . . . . . . . 383 Chart, Tire Sizing . . . . . . . . . . .
INDEX 507 Pressure Cap . . . . . . . . . . . . . Radiator Cap . . . . . . . . . . . . . Selection of Coolant (Antifreeze) Cruise Control (Speed Control) . . Cupholders . . . . . . . . . . . . . . . . Customer Assistance . . . . . . . . . . . . . . . . . . . . . 445 . . . . . . . . . . . . 445 . . . . . . 444,474,475 . . . . . . . . . . . . 151 . . . . . . . . . . . . 179 . . . . . . . . . . . . 495 Data Recorder, Event . . . . . . . . . . . . . . . . . . . . . . 60 Daytime Running Lights . . . . . . . .
508 INDEX Electronic Vehicle Information Center (EVIC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159,233 Electronically Shifted Transfer Case . . . . . . . . 314,320 Emergency Brake . . . . . . . . . . . . . . . . . . . . . . . . 333 Emergency, In Case of Freeing Vehicle When Stuck . . . . . . . . . . . . . . . 422 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 406 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . 419 Tow Hooks . . . . . . . . . . . . . . . . . . . .
INDEX 509 Flexible Fuel Vehicles Cruising Range . . . . . . . . . . . . . . . . . . . . . . . 380 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 380 Fuel Requirements . . . . . . . . . . . . . . . . . . 378,379 Replacement Parts . . . . . . . . . . . . . . . . . . . . . 381 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380 Flooded Engine Starting . . . . . . . . . . . . . . . . . . . 298 Fluid, Brake . . . . . . . . . . . . . . . . . . . . . . . . . . .
510 INDEX Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . 374 Gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232 Coolant Temperature . . . . . . . . . . . . . . . . . . . 217 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217 Oil Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 221 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . 218 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . 217 Voltmeter . . . . . . . . .
INDEX 511 Hitches Trailer Towing . . . . . . . . . . . . . . . . . . . . . Hoisting . . . . . . . . . . . . . . . . . . . . . . . . . . . HomeLink威 (Garage Door Opener) Transmitter Hood Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390 419 164 137 Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12,14 Ignition Key Removal . . . . . . . . . . . . . . . . . . . . .
512 INDEX LATCH (Lower Anchors and Tether for CHildren) . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Leaks, Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363 Light Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77,138 Airbag . . . . . . . . . . . .
INDEX 513 Tire Pressure Monitoring (TPMS) . . . . . . . . . . . 227 Traction Control . . . . . . . . . . . . . . . . . . . . . . . 343 Turn Signal . . . . . . . . . . . . . . . . 77,144,466,467,470 Warning (Instrument Cluster Description) . . 213,217 Limited-Slip Differential . . . . . . . . . . . . . . . . 327,450 Loading Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 383 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354 Locks . . . . . . . . . . . . . . . . . . . . . . .
514 INDEX Mopar Parts . . . . . . . . . . . . . . . . . . . . . . . . . 432,498 Multi-Function Control Lever . . . . . . . . . . . . . . . 144 Navigation System (uconnect gps) . . . . . . . . . . . . 159 New Vehicle Break-In Period . . . . . . . . . . . . . . . . 74 Occupant Restraints . . . . . . . . . . . . . . . . . . . . . . . 39 Octane Rating, Gasoline (Fuel) . . . . . . . . . . . . . . 373 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221 Trip . . . . . . . . . . . . . . . . . .
INDEX 515 Panic Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Park Sense System, Rear . . . . . . . . . . . . . . . . . . . 154 Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . 333 Passing Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 Pedals, Adjustable . . . . . . . . . . . . . . . . . . . . . . . 150 Personal Settings . . . . . . . . . . . . . . . . . . . . . . . . 243 Pets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
516 INDEX Recreational Towing . . . . . . . . . . . . . . . . . . . . . . 400 Shifting into Transfer Case Neutral (N) . . . . . . . 401 Shifting out of Transfer Case Neutral (N) . . . . . 402 Reformulated Gasoline . . . . . . . . . . . . . . . . . . . . 374 Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 438 Reminder, Seat Belt . . . . . . . . . . . . . . . . . . . . . . . 49 Remote Control Starting System . . . . . . . . . . . . . . . . . . . . . . . . 26 Remote Keyless Entry (RKE) . .
INDEX 517 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124,132 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 124 Child . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Folding Floor . . . . . . . . . . . . . . . . . . . . . . . . . 190 Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 Memory . . .
518 INDEX Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26,297 Automatic Transmission . . . . . . . . . . . . . . . . . 297 Engine Fails to Start . . . . . . . . . . . . . . . . . . . . 298 Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Starting Procedures (Gas Engines) . . . . . . . . . . . . 297 Steering Power . . . . . . . . . . . . . . . . . . . . . . . . . . . 331,332 Wheel, Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 519 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 363 Load Capacity . . . . . . . . . . . . . . . . . . . . . . . . 354 Pressure Monitor System (TPMS) . . . . . . . . . . . 368 Pressure Warning Light . . . . . . . . . . . . . . . . . . 227 Quality Grading . . . . . . . . . . . . . . . . . . . . . . . 501 Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . 364 Rotation . . . . . . . . . . . . . . . . .
520 INDEX Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . 303 Automatic . . . . . . . . . . . . . . . . . . . . . . 303,307,451 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 476 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 451 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 Transmitter Battery Service (Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 25 Transmitter, Garage Door Opener (HomeLink威) . .
INDEX 521 Wheel and Wheel Trim Care . . . . . . . . . . . . . . . . 456 Wheel Nut Torque . . . . . . . . . . . . . . . . . . . . . . . 417 Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 37,172 Window Airbag (Side Curtain) . . . . . . . . . . . . . . . 52 Window Fogging . . . . . . . . . . . . . . . . . . . . . . . . 291 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Rear Sliding . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
RAM ram truck T RU CK 2009 2009 OWNER’S MANUAL Chrysler LLC 81-326-0931 148922_09 Dodge Ram Gas.indd 1 Second Edition Printed in U.S.A.
