SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number . . . . . . . . . . . . . . 6 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Modifications / Alterations . . . . . . . . . . 6 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 1
INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 9 ▫ Central Locking—If Equipped . . . . . . . . . . . . .14 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . . 9 ▫ Door Ajar Warning . . . . . . . . . . . . . . . . . . . . .14 ▫ Automatic Transaxle Ignition Interlock System . . 9 ▫ Automatic (Rolling) Door Locks . . . . . . . . . . . .14 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ General Information . . . . . . . . . . . . . . . . . . . .18 ▫ Transmitter Battery Service . . . . . . . . . . . . . . .18 䡵 Vehicle Theft Alarm . . . . . . . . . . . . . . . . . . . . .19 ▫ Tamper Alert . . . . . . . . . . . . . . . . . . . . . . . . .19 ▫ Security System Manual Override . . . . . . . . . . .19 䡵 Trunk Lock And Release . . . . . . . . . . . . . . . . . .20 䡵 Trunk Safety Warning . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS CAUTION! An unlocked car is an invitation to thieves. Always remove the key from the ignition, lock the doors, and close the windows when leaving the vehicle unattended. Ignition Key Removal 9 Place the shift lever in PARK and make sure that the gearshift knob push button has returned to the out position. Turn the key to the Lock position and remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SENTRY KEY — IF EQUIPPED With this system, an electronically coded ignition key sends a signal to the vehicle electronics. If the electronics recognizes the signal, the vehicle will start and continue to run. If the system does not recognize the signal the vehicle will start and run for 2 seconds then shut off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Replacement Keys Turn the ignition Off and remove the first key. NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it can not be programmed to any other vehicle. 2. Insert the second valid key and switch the ignition On within 15 seconds. After ten seconds a chime will sound and the Theft Alarm Light will begin to flash.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ILLUMINATED ENTRY SYSTEM The interior lights will come on when you open either door, unlock the vehicle with the remote keyless entry or central unlock from the driver’s side (if so equipped). They will remain on for about 30 seconds after all doors are closed then fade to off. The lights also will turn off if you turn on the ignition after you close all doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 2 Power Door Lock Switch Door Lock Plunger If you press the door lock switch while the keys are in the ignition switch, and the driver’s door is open, the doors will not lock. If the door lock plunger is down when you shut the door, the door will lock. Therefore, make sure that the keys are not inside the vehicle before closing the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Central Locking—If Equipped Turning the driver’s door lock to the unlock position twice within five seconds will unlock both doors. Turning the key in the driver’s door to the unlock position once will unlock only the driver’s door. Locking the driver’s door with the key will lock both doors. The Automatic Door Locks can be disabled or re-enabled by performing the following procedure: 1. Close all doors and place the key in the ignition. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 1. Close all doors and place the key in the ignition. 2. Cycle the ignition switch between OFF and ON/RUN and back to OFF 4 times ending up in the OFF position. 3. Depress the power door lock switch to unlock the doors. 4. A single chime will indicate the completion of the programming. Power Door Lock Switch 4. A single chime will indicate the completion of the programming.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To unlock the doors: Press and release the UNLOCK button once to unlock the driver’s door. Press the button twice within 5 seconds to unlock all doors. If your vehicle is equipped with Illuminated Entry, the interior lights also come on and remain on for about 30 seconds, when you unlock the doors. 1. Press and hold the Lock button on the transmitter. NOTE: The system may be programmed to unlock all the doors upon the first press of the Unlock button.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To unlock the trunk: Press and hold the Trunk button on the transmitter to unlatch the trunk. NOTE: The transmitter can be programmed to unlatch the trunk immediately upon activation of the Trunk button (without pressing and holding) by performing the following procedure: 1. Press and hold the Unlock button on the transmitter. 2. Continue to hold the Unlock button, wait at least 4 but no longer than 10 seconds, then press the Trunk button. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Press and release the Lock and Unlock buttons simultaneously, followed by a press and release of ANY button on each new transmitter to be programmed as well as the original transmitter. You will hear a chime when a transmitter has been successfully programmed. You will have 30 seconds to finish programming all new transmitters. A chime will sound when the 30 seconds is over or the ignition switch is turned to the LOCK position. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch the battery, clean it with rubbing alcohol. 3. Reassemble the transmitter case. Snap the halves together and test transmitter operation. VEHICLE THEFT ALARM The system monitors the doors, trunk, and ignition for unauthorized operation. If something triggers the alarm, the system will signal for up to 18 minutes.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK LOCK AND RELEASE With the ignition ON, the word “deck” will be displayed in place of the odometer display indicating that the trunk is open. The odometer display will reappear once the trunk is closed or if the trip button is depressed. With the key in lock position or key out, the “deck” will be displayed until the trunk is closed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Trunk Internal Emergency Release 21 WINDOWS Power Windows 2 Emergency Release NOTE: As a security measure, a Trunk Internal Emergency Release lever is built into the trunk latching mechanism. In the event of an individual being locked inside the trunk, the trunk can be simply opened by pulling on the glow-in-the-dark handle attached to the trunk latching mechanism. See picture.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The window controls on the driver’s door operate all windows. The driver’s window switch has an Auto Down feature. Press the window switch past the detent, release, and the window will go down automatically. To open the window part way, pull the window switch part way and release it when you want the window to stop. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision which includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the front seat. Latch Plate To Buckle 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a ”click.” Latch Plate 2. The seat belt latch plate is on the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt go around your lap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is very dangerous.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt can’t do its job as well. In a collision it could even cut into you. Be sure the belt is straight. If you can’t straighten a belt in your vehicle, take it to your dealer and have it fixed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The pretensioners are triggered by the front airbag control module (see Airbag Section). Like the front airbags, the pretensioners are single use items. After a collision that is severe enough to deploy the airbags and pretensioners, both must be replaced.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Turn off the engine. A single chime will sound to signify that you have successfully completed the programming. The Enhanced Warning System (BeltAlert) can be reactivated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver’s seat belt remains unbuckled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver and Right Front Passenger Supplemental Restraint System (SRS) - Airbag 29 NOTE: These airbags are certified to the new Federal regulations that allow less forceful airbags. WARNING! Front Airbag Components This vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s airbag is mounted in the center of the steering wheel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The seat belts are designed to protect you in many types of collisions. The front airbags deploy only in moderate to severe frontal collisions. But even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years old and under should ride buckled up in the rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during airbag deployment could cause serious injury. Airbags need room to inflate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE wheel and column. If the key is in the “off” position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate. • The airbag control module also turns on the AIRBAG light in the instrument panel for 6 to 8 seconds when the ignition is first turned on, then turns the light off. If it detects a malfunction in any part of the system, it turns on the light either momentarily or continuously.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system. This does not mean something is wrong with the airbag system. irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or frame.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children 12 years and under should ride properly buckled up in a rear seat. According to crash statistics, children are safer when properly restrained in the rear seat rather than in the front. WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward facing infant restraint should only be used in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE than one year. These child seats are also held in the vehicle by the lap/shoulder belt or the LATCH child restraint anchorage system. (See the LATCH — Child Seat Anchorage System Section.) The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE connection to the top tether anchorages have been available for some time. For some older child restraints, many child restraint manufacturers offer add-on tether strap kits or retro-fit kits. You are urged to take advantage of all the available attachments provided with your child restraint in any vehicle. Latch Anchorages Both rear seating positions have lower anchorages that are capable of accommodating LATCH-compatible child seats.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provided with the child restraint system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE installing the child restraint buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach. If the buckled seat belt interferes with the child restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 To attach a child restraint tether strap: 1. Lift the carpet flap to expose the anchor directly behind the seat where you are placing the child restraint. 2 Hook And Anchor WARNING! Child Tether Anchor Location 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. 3.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. ENGINE BREAK-IN RECOMMENDATIONS The engine in your new vehicle does not require a long break-in period.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 must remain open, close all windows. Adjust the heating or cooling system to force outside air into the vehicle. Set the blower at high speed. SAFETY TIPS Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defrosters Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Convertible Top Operation . . . . . . . . . . . . . . . .47 䡵 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 ▫ To Lower The Top . . . . . . . . . . . . . . . . . . . . . .47 ▫ Manual Front Seat Adjustments . . . . . . . . . . . .59 ▫ To Raise The Top . . . . . . . . . . . . . . . . . . . . . .49 ▫ Power Driver’s Seat . . . . . . . . . . . . . . . . . . . . .60 ▫ Top Cover Installation . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Multi-Function Control Lever . . . . . . . . . . . . . .67 䡵 Electronic Speed Control— If Equipped . . . . . .72 ▫ Headlights, Parking Lights, Instrument Panel Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 ▫ To Activate . . . . . . . . . . . . . . . . . . . . . . . . . . .72 ▫ Automatic Headlights—If Equipped . . . . . . . . .68 ▫ Daytime Running Lights (Canada Only) . . . . . .68 ▫ Lights-On Reminder . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONVERTIBLE TOP OPERATION WARNING! The convertible top does not provide the structural protection that a reinforced metal roof does, and the fabric top cannot be expected to prevent the ejection of the occupants of a vehicle in a collision. Therefore it is important that all occupants wear their seat belts at all times when riding in a convertible.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Release the top from the windshield header by pulling both latch handles rearward until the latch hooks are free. NOTE: The Power Top Switch has two detent positions for lowering the convertible top. Pressing and holding the Power Top Switch lightly in the first detent position will automatically lower the convertible top. Pressing and holding the switch in the second detent position will lower all four windows and the top to the full down position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Damage to the top material could result if the latch handles are not completely closed when the top is lowered. The convertible top cover cannot be installed while the latch handles are open. 49 NOTE: If the power convertible top system fails, raise the top by manually pulling the top until it meets the windshield and open both front latch handles. Pull the top until the two pins are seated in the windshield header.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Press the Power Top Switch to raise the top. Before the top reaches the windshield, open both front latch handles. Press the switch again to continue raising the top until the two pins seat themselves in the windshield header. 4. Use the center pull cup to pull down on the header. Hook each latch hook to its striker. Latch both sides. CAUTION! Car top carriers, ski racks, etc.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Installation From Inside The Vehicle 1. Kneel on the rear seat and tuck the rear edge and side edges of the top cover under the black molding near the trunk. 51 2. Insert both tabs located on the front of the top cover in between the seatback and seatback bracket.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Snap the top cover flaps to the inner trim panel snaps. The side of the seat back cushion hides the snap. 4. Press down on the forward portion of the top cover to engage the hook and loop fasteners.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Installation From Outside The Vehicle 1. Start on one side of the vehicle and tuck as much of the top cover as possible under the black molding. 53 2. Snap the top cover flap to the inner trim panel snap. (The side of the seat back cushion hides the snap.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Tuck the top cover tab closest to you into the space between the seatback and the seatback bracket. 5. Snap the remaining top cover flap to the inner trim panel snap. 4. Walk to the other side of the vehicle and finish tucking the top cover under the black molding. Insert the remaining tab between the seatback and the seatback bracket.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Press down on the forward portion of the top cover to engage the hook and loop fasteners. 55 CONSOLE FEATURES 3 Console Features Hook and Loop Fasteners Top Cover Removal Unsnap the snaps and disengage the hook and loop fasteners, slide the tabs from the rear seat and then from the rear of the top storage area. Remove the top cover, fold, and store in the trunk or a dry secure area. The front console has two cup holders.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE passengers and a rear courtesy lamp located directly in back of the center console. The center console can be locked using the “master” key. Two coin holders are located toward the front of the inside of the console bin. Both can also accommodate various combinations of different types of coins, including some international currencies. The slot on the far left side is not for coins, but for an optional power outlet, if so equipped.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 57 Electric Remote-Control Mirrors Both of the outside mirrors can be adjusted by using the remote controls mounted on the instrument panel located to the left of the steering wheel. 3 Automatic Dimming Mirror CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror Adjustment — Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror. Right Side Mirror Adjustment Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle. Illuminated Vanity Mirrors An illuminated vanity mirror is on each sun visor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 59 Forward/Rearward — If Equipped The adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position. Reclining Bucket Seats The recliner control is on the side of the seat. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under a power seat as it may cause damage to the seat controls. 61 This feature heats the front driver and passenger seats on models equipped with leather seats. The controls for the heated seats are located in the floor console next to the parking brake.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Fold The Front Seatback Forward: Turn the high mounted release lever rearward and fold the seatback forward. If you release the lever early, a safety feature locks the seat into that position. Turn the release lever again to continue lowering the seat. Just before the seatback reaches the full forward position, a soft “click “ will be heard. This is a signal that the seatback is unlocked and can be raised without the use of the release handle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjust the restraints so that the upper edge is as high as practical. To raise, pull up on the head restraint. To lower, depress the button on the post guide and push down on the head restraint. 63 TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. LIGHTS Hood Safety Catch Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole marked “prop” on the underside of the hood. To prevent possible damage, do not slam the hood to close it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65 3 NOTE: The map lights will remain on until the mirror switches have been turned to the OFF position, so be sure that they have been turned off before leaving the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE turn on the lights. Turn the panel dimmer switch fully clockwise to prevent the lights from coming on when a door is opened. NOTE: The interior lights have a “fade to off” feature. When the lights are turned off, they gradually “fade” off. Interior light Defeat (OFF) Rotate the dimmer control to the extreme bottom full-circle position. The interior lights will remain off when the doors are open.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 Multi-Function Control Lever 3 Multi-Function lever Multi-Function Lever The Multi-Function lever controls the operation of the headlights, turn signals, headlight beam select switch, instrument panel light dimming, passing light, dome light, and fog lights. Headlights, Parking Lights, Instrument Panel Lights Turn the end of the Multi-Function lever to the first detent for parking light operation. Turn to the second detent for headlight operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Headlights—If Equipped This system automatically turns your headlights on at a preset level of outdoor lighting. Turn the end of the control lever to the third detent to turn the system on. When the system is on, the headlight delay feature is also on. This means that your headlights will stay on for about 90 seconds after you turn the ignition switch off. To turn the Automatic system off, turn the control lever clockwise, to the off position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlight Beam Select Switch Pull the turn signal lever towards you to switch the headlights to HIGH beam. Pull the turn signal lever a second time to switch the headlights to LOW beam. 69 WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch in the right side control lever. Turn the end of the control lever to select the desired wiper speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for several cycles after the lever is released, and then resume the intermittent interval previously selected. If the lever is pulled while in the OFF position, the wipers will operate for several cycles, then turn OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 TRACTION CONTROL— IF EQUIPPED To turn the Traction Control System Off, press the switch located on the top of the steering column, to the right of the hazard switch, until the Traction Control indicator in the instrument cluster lights up. Tilt Steering Column Control WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering column, you could lose control of the vehicle and have an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Traction Control System is enabled each time the ignition switch is turned On. This will occur even if you used the switch to turn the system off before powering down or turning the ignition to Lock. ELECTRONIC SPEED CONTROL— IF EQUIPPED When engaged, this device will control the throttle operation to maintain a constant vehicle speed between 30 mph (48 km/h) and 85 mph (137 km/h). The controls are on the steering wheel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate: A soft tap on the brake pedal, pushing the CANCEL button, or normal brake or clutch pressure will deactivate speed control without erasing the memory. Pushing the ON/OFF button or turning off the ignition turns the speed control system off and erases the memory. To Resume Speed: To resume a previously set speed, push and release the RESUME/ACCEL button. Resume can be used at any speed above 25 mph (40 km/h).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When Climbing A Hill If vehicle speed drops 3 mph (5 km/h) below the Speed Control set speed, the transaxle will downshift to third gear. Under severe conditions the transaxle may downshift again to second gear. The transaxle will upshift to fourth gear after the vehicle has reached the top of the hill. When Descending A Hill If vehicle speed rises 3 mph (5 km/h) over the Speed Control set speed, the transaxle will downshift to third gear.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED The HomeLink威 Universal Transceiver replaces up to three remote controls (hand held transmitters) that operate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button. The Universal Transceiver operates off your vehicle’s battery and charging system; no batteries are needed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicle exhaust contains carbon monoxide, a dangerous gas. Do not run the vehicle’s exhaust while training the transceiver. Exhaust gas can cause serious injury or death. 3. Choose one of the three Universal Transceiver buttons to program. Place the hand held controller one to three inches from the Universal Transceiver while keeping its indicator light in view.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. The indicator light in the Universal Transceiver will begin to flash, first slowly and then rapidly. The rapid flashing indicates successful programming. If after 90 seconds the indicator light does not flash rapidly or goes out, return to step 1 and repeat the procedure. To train the other buttons, repeat steps 3 and 4. Be sure to keep your hand held transmitters in case you need to retrain the Universal Transceiver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE difficulty in locating the training button, check your garage door opener manual, or call 1-800-355-3515 or, on the Internet, at www.homelink.com. 2. Press and hold the training button on the garage door opener head unit This will activate the “training” light. NOTE: After completing step 2, you have 30 seconds to start step 3. 3. Return to the Universal Transceiver in the vehicle and firmly press and release the garage door button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Reprogramming A Single Button 1. This device may not cause harmful interference. 1. Press and hold the Universal Transceiver button to be reprogrammed. Do not release until step 4 has been completed. 2. This device must accept any interference that may be received including interference that may cause undesired operation. 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Electrical Outlet Use With Engine Off • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instruments And Controls . . . . . . . . . . . . . . . . .85 ▫ To Set The Clock . . . . . . . . . . . . . . . . . . . . . . .99 䡵 Instrument Cluster Standard . . . . . . . . . . . . . . .86 䡵 Radio General Information . . . . . . . . . . . . . . . .99 䡵 Instrument Cluster Premium . . . . . . . . . . . . . . .87 ▫ Radio Broadcast Signals . . . . . . . . . . . . . . . . . .99 䡵 Instrument Cluster – GTC Model . . . . . . . . . . .88 ▫ Two Types Of Signals .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Seek Button (Radio Mode) . . . . . . . . . . . . . . . 101 ▫ Scan Button . . . . . . . . . . . . . . . . . . . . . . . . . 105 ▫ Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 ▫ Changing Tape Direction . . . . . . . . . . . . . . . . 105 ▫ Radio Data System (RDS) . . . . . . . . . . . . . . . 101 ▫ Metal Tape Selection . . . . . . . . . . . . . . . . . . . 105 ▫ PTY (Program Type) Button . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 83 ▫ CD Changer Control Capability — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 108 䡵 Sales Code RB1—AM/FM Stereo Radio With DVD/GPS Navigation System . . . . . . . . . . . . 120 䡵 Sales Code RBB—AM/FM Stereo Radio With Cassette Tape Player And CD Changer Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 䡵 6 Disc CD Changer — If Equipped . . . . . . . . . 120 ▫ Radio Operation . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Satellite Radio — If Equipped . . . . . . . . . . . . . 123 ▫ System Activation . . . . . . . . . . . . . . . . . . . . . 123 ▫ Electronic Serial Number/Sirius Identification Number (ENS/SID) . . . . . . . . . . . . . . . . . . . . 123 ▫ Selecting Satellite Mode In RBB, RAH And RBK Radios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 䡵 Remote Sound System Controls — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 85 INSTRUMENTS AND CONTROLS 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER STANDARD
UNDERSTANDING YOUR INSTRUMENT PANEL 87 INSTRUMENT CLUSTER PREMIUM 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER – GTC MODEL
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gauge When the ignition key is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Traction Control — If Equipped This display indicator illuminates momentarily as a bulb check when the ignition switch is first turned ON. The indicator will blink during an active traction event, but will remain solid when the system is deactivated or if a system malfunction occurs.
UNDERSTANDING YOUR INSTRUMENT PANEL light stays on, or comes on while driving, have the system checked by an authorized dealer. (See page 72 for more information.) 5. Tachometer The red area of the scale shows the maximum permissible engine revolutions-per-minute (rpm x 1000) for each gear range. Before reaching the red area (over 6,500 rpm), ease up on the accelerator to prevent engine over speed. 6.
UNDERSTANDING YOUR INSTRUMENT PANEL your Owner Manual for more details). If the bulb does not come on when turning the key from OFF to ON, have the condition checked promptly. Certain conditions such as a loose or missing gas cap or poor fuel quality may illuminate the light after engine start. The vehicle should be serviced if the light stays on through several of your typical driving cycles. In most situations the vehicle will drive normally and will not require towing.
UNDERSTANDING YOUR INSTRUMENT PANEL 14. Transmission Range Indicator This indicator illuminates to show the automatic transmission gear selection. An optional AutoStick Gear Indicator displays the current transaxle gear when in AutoStick mode. 15. Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven.
UNDERSTANDING YOUR INSTRUMENT PANEL 17. Oil Pressure Light Shows low engine oil pressure. The light will come on and remain on briefly when the ignition is turned on as a bulb check. If the bulb does not come on during starting, have the bulb repaired promptly. If the light comes on and remains on while driving, stop the vehicle and shut off the engine. Do not operate the vehicle until the cause is corrected. The light does not show the quantity of oil in the engine.
UNDERSTANDING YOUR INSTRUMENT PANEL In an ABS equipped vehicle, the Brake System Warning light will come on if the ABS light is not functioning or if the ABS system is not communicating. 19. Seat Belt Reminder Light When the ignition switch is first turned ON, this light will turn on for 5 to 8 seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound.
UNDERSTANDING YOUR INSTRUMENT PANEL COMPASS, TEMPERATURE, AND TRIP COMPUTER DISPLAY — IF EQUIPPED 95 Reset The following trip conditions can be reset: • AVG ECO (changes to present fuel economy) • ODO • ET To reset only the trip condition currently displayed, press and release the STEP and US/M buttons simultaneously until a chime sounds. To reset all trip conditions, hold down the STEP and US/M buttons simultaneously (about 2 seconds) until a second chime sounds and then release the buttons.
UNDERSTANDING YOUR INSTRUMENT PANEL Trip Conditions Average Fuel Economy (AVG ECO) This display shows the average fuel economy since the last reset. Estimated Range (DTE) This display shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is based on the most recent trip information: (Average Fuel Economy) x (Fuel Remaining) This display cannot be reset. Present Fuel Economy (ECO) This display shows fuel economy for the last few seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Compass Calibration The self-calibrating feature of the compass eliminates the need to calibrate the compass for normal conditions. During a short initial period, the compass may appear erratic and the CAL symbol will appear on the display. After the vehicle has completed at least one complete circle in an area free from large metal objects, calibration will be complete when the CAL symbol is extinguished.
UNDERSTANDING YOUR INSTRUMENT PANEL Setting the Compass Variance Refer to the variance map for the correct compass variance zone. To check the variance zone, the ignition must be on and the compass / temperature displayed. Hold down both the US / M and STEP buttons simultaneously until the VAR symbol is lit and then immediately release both buttons. The current variance zone will now be displayed. To change the zone, press the STEP button until the correct zone is displayed. Wait for about 5 seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 99 Outside Temperature If the outside temperature is more than 131°F (55°C), the display will show 131°F. When the outside temperature is less than ⫺40°F (⫺40°C), the display will show ⫺40°F/C. To Set The Clock: CIGAR LIGHTER/ASHTRAY For a nominal charge your dealer can provide a “smoker’s” package. This package consists of a cigar lighter and an ashtray that utilizes one of the cup holders. 2. Press any other button to exit from the clock setting mode.
UNDERSTANDING YOUR INSTRUMENT PANEL Two Types of Signals There are two basic types of radio signals... AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary... and FM or Frequency Modulation, in which the frequency of the wave is varied to carry the sound. SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER AND CD CHANGER CONTROLS NOTE: The radio sales code is located on the lower left side of your radio faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch, Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. The volume will be displayed and continuously updated while the button is pressed. Seek Button (Radio Mode) Press and release the Seek button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. Holding the button will by pass stations until you release the button.
UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the PTY button to select the following format types: Program Type Adult Hits Classical Classic Rock College Country Information Jazz Foreign Language News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Radio Display Adlt Hit Classicl Cls Rock College Country Inform Jazz Language News Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Program Type Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weathe
UNDERSTANDING YOUR INSTRUMENT PANEL Pressing PTY, then SCAN will scan the FM Band and stop at all RDS stations. Each RDS station will be played for a 5 second scan once around the FM Band and stop at the last station. The PTY icon will then turn off. Balance The Balance control adjusts the left-to-right speaker balance. Push in the button and it will pop out. Adjust the balance and push the button back in. The balance will be displayed and continuously updated while the button is turned.
UNDERSTANDING YOUR INSTRUMENT PANEL 5 seconds after pressing the SET button, the station will continue to play but will not be locked into push-button memory. You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into memory.
UNDERSTANDING YOUR INSTRUMENT PANEL 105 Tape Eject Press the EJT Tape button and the cassette will disengage and eject from the radio. Noise Reduction The Dolby Noise Reduction System* is on whenever the tape player is on, but may be switched off. Scan Button Press this button to play 10 seconds of each selection. Press the scan button a second time to cancel the feature. To turn off the Dolby Noise reduction System: Press the Dolby button (button 2) after you insert the tape.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! This CD player will accept 4 3⁄4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. Inserting The Compact Disc The CD player contained within the radio is not a multi-disc changer, and will only accept one CD. Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD Player.
UNDERSTANDING YOUR INSTRUMENT PANEL FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Program Button 4 (Random Play) Press this button while the CD is playing to activate Random Play. This feature plays the tracks on the selected disc in random order to provide an interesting change of pace. 107 To select Satellite Radio (if equipped), press the MODE button until the word SIRIUS appears.
UNDERSTANDING YOUR INSTRUMENT PANEL CD Changer Control Capability — If Equipped This radio is compatible with a remote mounted CD changer available through Mopar Accessories. The following instructions are for the radio controls that operate this CD changer. Mode Button To activate the CD changer, press the MODE button until CD information appears on the display. Disc Up/Program Button 1 Press the DISC up (button 1) button to play the next available disc.
UNDERSTANDING YOUR INSTRUMENT PANEL 109 An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following reasons: • Excessive vibration • Disc inserted upside down • Damaged disc 4 • Water condensation on optics SALES CODE RBB—AM/FM STEREO RADIO WITH CASSETTE TAPE PLAYER AND CD CHANGER CAPABILITY NOTE: The radio sales code is located on the lower left side of your radio faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the volume control to the right increases the volume and to the left decreases it. When the audio system is turned on, the sound will be set at the same volume level as last played. For your convenience, the volume can be turned down, but not up, when the audio system is off and the ignition is ON.
UNDERSTANDING YOUR INSTRUMENT PANEL Audio The audio button controls the BASS, TREBLE, BALANCE, and FADE. Press the AUDIO button and BASS will be displayed. Press the SEEK + or SEEK – to increase or decrease the Bass tones. Press the AUDIO button a second time and TREB will be displayed. Press the SEEK + or SEEK – to increase or decrease the Treble tones. Press the AUDIO button a third time and BAL will be displayed. Press the SEEK + or SEEK – to adjust the sound level from the right or left side speakers.
UNDERSTANDING YOUR INSTRUMENT PANEL Cassette Player Features With ignition OFF and the sound system OFF, you can eject the tape cassette by pushing the EJECT button. You can turn the tape player ON by inserting a cassette or activating the MODE button (with a cassette in the radio), but only when the ignition and radio are on. Each time a cassette is inserted the tape player will begin playing on the side of the cassette that is facing up in the player.
UNDERSTANDING YOUR INSTRUMENT PANEL 113 When Dolby is ON, the NR symbol appears on the display. Each time a tape is inserted the Dolby will turn ON. Seek Button Press the SEEK up or down to select another track on the same disc. A SEEK symbol will appear on the display. * “Dolby” noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. Dolby and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically. NOTE: The radio sales code is located on the lower left side of your radio faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up or the bottom to seek down.
UNDERSTANDING YOUR INSTRUMENT PANEL Press the AUDIO button and BASS will be displayed. Press the SEEK + or SEEK – to increase or decrease the Bass tones. Time Press the TIME button to change the display between radio frequency and time. Press the AUDIO button a second time and TREB will be displayed. Press the SEEK + or SEEK – to increase or decrease the Treble tones. General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada.
UNDERSTANDING YOUR INSTRUMENT PANEL Inserting The Compact Disc CAUTION! 117 beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection. This CD player will accept 4 3⁄4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. EJT — Eject Press the EJT button and the disc will unload and move to the entrance for easy removal. The unit will switch to the radio mode.
UNDERSTANDING YOUR INSTRUMENT PANEL Press the SEEK button to move to the next randomly selected track. Press the RND (button 4) button a second time to stop Random Play. Mode Press the MODE button repeatedly to select between the CD player, the optional remote CD changer and the Satellite Radio (if equipped). When Satellite Radio (if equipped) is selected “SAT” will appear in your radio display. Mode Button To activate the CD changer, press the MODE button until CD information appears on the display.
UNDERSTANDING YOUR INSTRUMENT PANEL Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an interesting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RB1—AM/FM STEREO RADIO WITH DVD/GPS NAVIGATION SYSTEM system and the CD Player simultaneously. Always remove the Navigation DVD before inserting another disc. 6 DISC CD CHANGER — IF EQUIPPED The CD changer is located below the radio in the instrument panel. The changer plays only 4 3⁄4 inch (12 cm) discs. The changer holds up to 6 discs. Each disc is loaded and ejected through a single slot in front of the changer.
UNDERSTANDING YOUR INSTRUMENT PANEL Loading the CD Changer When inserting the first CD into the changer if the radio is on, wait until the single slot is illuminated on both sides and simply insert the first disc. To insert additional CDs into the changer, the instructions follow: 1. Select and press any numbered button without an illuminated light above it. 2. Insert the CD while the light above the chosen button is flashing and the two lights on either side of the slot are illuminated. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Button 1 Press this button to play the next available disc. Program Button 4 (Random Play) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the current compact disc in random order to provide an interesting change of pace. The CD changer stays in the random play mode when changing to the next disc. NOTE: The changer will not random play between discs.
UNDERSTANDING YOUR INSTRUMENT PANEL To eject additional CDs from the changer, first select the numbered button where the CD is located and then press the EJT button. CD Changer Operation with the Changer Off The CD changer is able to load and eject discs with the ignition power off. However, while the ignition is off, one of the six numbered buttons must be pressed first.
UNDERSTANDING YOUR INSTRUMENT PANEL ESN/SID Access With RBP, RBU, RAZ, RB1 and RBQ Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and TIME buttons simultaneously for 3 seconds. All twelve ESN/SID numbers will be displayed. The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF, or 5 minutes has passed since any button was pushed.
UNDERSTANDING YOUR INSTRUMENT PANEL 125 888-539-7474 to discuss options for channel blocking or unblocking. Please have your ESN/SID information available. one and stop the search. Pressing a pre-set memory button during a music type scan, will call up the memory channel and stop the search. Storing and Selecting Pre-Set Channels In addition to the 10 AM and 10 FM pre-set stations, you may also commit 10 satellite stations to push button memory.
UNDERSTANDING YOUR INSTRUMENT PANEL • Dense tree coverage may interrupt reception in the form of short audio mutes. • Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage. REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches.
UNDERSTANDING YOUR INSTRUMENT PANEL The left hand control is a rocker type switch with a push-button in the center. The function of the left hand control is different depending on which mode you are in. The following describes the left hand control operation in each mode. Radio Operation Pressing the top of the switch will “Seek” up for the next listenable station and pressing the bottom of the switch will “Seek” down for the next listenable station.
UNDERSTANDING YOUR INSTRUMENT PANEL CASSETTE TAPE AND PLAYER MAINTENANCE To keep the cassette tapes and player in good condition, take the following precautions: turned all the way down. To prevent this, you should periodically clean the head with a commercially available WET cleaning cassette. 1. Do not use cassette tapes longer than C-90; otherwise, sound quality and tape durability will be greatly diminished. As preventive maintenance, clean the head about every 30 hours of use.
UNDERSTANDING YOUR INSTRUMENT PANEL 6. Do not expose the disc to direct sunlight. CLIMATE CONTROLS 7. Do not store the disc where temperatures may become too high. Automatic Temperature Control (ATC) — If Equipped NOTE: If you experience difficulty in playing a particular disc, it may be damaged, oversized, or have theft protection encoding. Try a known good disc before considering disc player service. You may have a problem with CD-R (recordable) and CD-RW (recordable and writable) disks.
UNDERSTANDING YOUR INSTRUMENT PANEL near the windshield glass. The In-Car Temperature Sensor is mounted behind the ATC control panel. These sensors transmit data on sun strength and vehicle interior temperatures to enhance system performance. CAUTION! Do not cover either sensor with any foreign material as improper operation of the system will result. Level Of Automatic Control 72°F (22°C) is the recommended setting for maximum comfort for the average person, however, this may vary.
UNDERSTANDING YOUR INSTRUMENT PANEL 61,....to 89,90, Hi, for automatic temperature control. You can select a very hot or cold comfort setting by holding the comfort control until it reaches its highest or lowest levels. The system adjusts to bring the interior temperature to the desired comfort level. All comfort settings are automatic; even Hi and Low. NOTE: You can change the display from U.S.
UNDERSTANDING YOUR INSTRUMENT PANEL Air Direction Buttons (Mode) These buttons allow you to select from five air distribution patterns. These buttons should be used only when you can not achieve comfort or visibility in Auto operation. A symbol in the display window will show which mode is operating. Panel Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct air flow. This mode is not recommended when heat is required.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The air conditioning compressor is on in this mode. This dehumidifies the air to help dry the windshield. To improve fuel economy, leave in the defrost mode only when necessary. Rear Window Defroster Press the button once to turn on the Rear Window Defroster and a second time to turn it off. An indicator light in the control shows that the defroster is on. NOTE: The defroster turns off automatically after 15 minutes of operation.
UNDERSTANDING YOUR INSTRUMENT PANEL Side Window Demisters Side window demisters are located on the instrument panel. These non adjustable outlets direct air toward the side windows in any mode except Panel or Panel Recirculation. The air is directed toward the area of the side windows through which you view the outside rearview mirrors. Rear Seat Outlets These outlets are located under the front seats and direct warm air to the rear seat passengers.
UNDERSTANDING YOUR INSTRUMENT PANEL 135 Operating Tips (ATC only) 4
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the system is in the AUTO mode and the fan control is already rotated fully clockwise or fully counterclockwise, the control may have to be rotated to the middle and then to the desired fan setting for manual adjustment of fan speed. Manual Air Conditioning/Heater Control — If Equipped The Air Conditioning System allows you to balance the temperature, amount, and direction of air circulating throughout the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy. NOTE: If your air conditioning performance seems lower than expected, check the front of the air conditioning condenser for an accumulation of dirt or insects. The air conditioning condenser is located in front of the radiator.
UNDERSTANDING YOUR INSTRUMENT PANEL • Panel — Air Conditioning Outside air flows through the air conditioning system and then through the outlets located in the instrument panel. • Floor • Bi-Level — Air Conditioning Outside air flows through the air conditioning system and then through the outlets located in both the instrument panel and floor outlets. • Mix • Panel Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct air flow.
UNDERSTANDING YOUR INSTRUMENT PANEL Rear Seat Outlets These outlets are located under the front seats and direct warm air to the rear seat passengers. Air is directed through these outlets when you select either the Floor, Bi-Level, or Mix modes. Rear Window Defroster The Rear Window Defroster button is located to the right of the Mode Control. Press this button once to turn on the Rear Window Defrost and a second time to turn them off. A light above the button shows that the defroster is on.
UNDERSTANDING YOUR INSTRUMENT PANEL Summer Operation Air conditioned vehicles must be protected with a highquality antifreeze coolant to provide proper corrosion protection and to raise the boiling point of the coolant for protection against overheating. A 50 % concentration is recommended. Winter Operation The blower air will heat faster in cold weather if you use only the low blower speeds for the first 10 minutes of operation.
UNDERSTANDING YOUR INSTRUMENT PANEL 141 Operating Tips (Manual A/C Control Only) 4
UNDERSTANDING YOUR INSTRUMENT PANEL Outside Air Intake Make sure the air intake, directly in front of the windshield, is free of ice, slush, snow or other obstructions such as leaves. Leaves collected in the air-intake plenum may reduce air flow and plug the plenum water drains.
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 146 ▫ Automatic Transaxle . . . . . . . . . . . . . . . . . . . 146 ▫ Manual Transaxle . . . . . . . . . . . . . . . . . . . . . 146 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 146 ▫ Extreme Cold Weather (Below -20°F Or -29°C) . . . . . . . . . . . . . . . . . 147 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . . 148 ▫ After Starting . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 䡵 Tire Safety Information . . . . . . . . . . . . . . . . . . 158 䡵 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 ▫ Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . 158 䡵 Tire Rotation Recommendations . . . . . . . . . . . 175 ▫ Tire Identification Number (TIN) . . . . . . . . . . 162 䡵 AutoStick — If Equipped . . . . . . . . . . . . . . . . 176 ▫ Tire Loading And Tire Pressure . . . . . . . . . . . 163 ▫ AutoStick Operation . . . . . .
STARTING AND OPERATING 145 ▫ Fuel Requirements . . . . . . . . . . . . . . . . . . . . 182 䡵 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . . 185 ▫ Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles . . . . . . . . . . . . . 182 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 185 ▫ Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 ▫ Cruising Range . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust temperatures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. WARNING! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death.
STARTING AND OPERATING 147 CAUTION! Ignition Key Positions WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way.
STARTING AND OPERATING If Engine Fails to Start If the engine fails to start after you have followed the “NORMAL STARTING” or “EXTREME COLD WEATHER” procedures, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine. This should clear any excess fuel in case the engine is flooded. CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again.
STARTING AND OPERATING 149 WARNING! WARNING! Remember to disconnect the cord before driving. Damage to the 110-115 volt AC electrical cord could cause electrocution. Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle you should shift the transmission into Park, remove the key from the ignition, and apply the park brake.
STARTING AND OPERATING CAUTION! WARNING! Damage to the transaxle may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly on the brake pedal.
STARTING AND OPERATING Four Speed Automatic Transaxle The electronically controlled transaxle provides a precise shift schedule. The transaxle electronics are self calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few shift cycles. Reset Mode The transaxle is monitored electronically for abnormal conditions.
STARTING AND OPERATING WARNING! Your vehicle could move and injure you and others if it is not completely in P (Park). Check by trying to move the gearshift lever back and forth without depressing the shift button after you have set it in P. Make sure it is in Park before leaving the vehicle. WARNING! Never use the Park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.
STARTING AND OPERATING NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance, fuel economy, and extend transaxle life by reducing excessive shifting and heat build up. Use the “3” range when descending steep grades to prevent brake system distress. 153 PARKING BRAKE When the parking brake is applied with the ignition on, the brake light in the instrument cluster will come on. NOTE: This light only shows that the parking brake is on.
STARTING AND OPERATING To release the parking brake, apply the brake pedal and pull up on the parking brake lever. Push the release button and lower the lever fully. When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the transmission locking mechanism may make it difficult to move the selector out of Park.
STARTING AND OPERATING BRAKE SYSTEM Your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be much greater than that required with the power system operating. WARNING! Riding the brakes can lead to brake failure and possibly an accident.
STARTING AND OPERATING WARNING! WARNING! Pumping of the brake pedal will diminish the effectiveness of Anti-lock brakes and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
STARTING AND OPERATING POWER STEERING The power assisted steering system of your vehicle provides mechanical steering capability in the event power assist is lost. If for some reason the hydraulic pressure is interrupted, it will still be possible to steer your vehicle. Under these conditions you will observe a substantial increase in steering effort. 157 TRACTION CONTROL — IF EQUIPPED The Traction Control System will improve acceleration and steering on slippery surfaces by reducing tire spin.
STARTING AND OPERATING A push-button located on the top of the steering column turns the Traction Control System ON or OFF. The system is always in the “ON” mode unless: • The traction control switch has been used to turn the system off; If your vehicle becomes stuck in mud, ice, or snow, turn the Traction Control System Off before attempting to “rock” the vehicle free.
STARTING AND OPERATING 159 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H • Temporary Spare tires are high pressure compact spares designed for temporary emergency use only. Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designation.
STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm) 65 = Aspect Ratio in Percent (%) —Ratio of section height to section width of tire. 10.
STARTING AND OPERATING 161 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved under specified operating conditions. (i.e. tire pressure, vehicle loading, road conditions and posted speed limits).
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure 163 Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar.
STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information” placard and in the “Vehicle Loading” section of this manual.
STARTING AND OPERATING 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE: The following table shows examples on how to calculate total load, cargo/luggage and towing capacities of your vehicle with varying seating configurations and 165 number and size of occupants.
STARTING AND OPERATING
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle. Three primary areas are affected by improper tire pressure: 167 1.
STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3. Ride Comfort and Vehicle Stability— Proper tire inflation contributes to a comfortable ride. Overinflation produces a jarring and uncomfortable ride.
STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure”. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1 km) after a 3 hour period.
STARTING AND OPERATING WARNING! High speed driving with your vehicle under maximum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized tire dealer for radial tire repairs.
STARTING AND OPERATING 171 Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. tire affects vehicle handling. Since it is not the same tire, replace (or repair) the original tire and reinstall on the vehicle at the first opportunity. Do not install more than one compact spare tire/wheel on the vehicle at any given time.
STARTING AND OPERATING WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed. Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced.
STARTING AND OPERATING Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING 175 TIRE CHAINS Due to limited clearance, tire chains are not recommended. Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). CAUTION! Tire Rotation Recommendations Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving and braking functions.
STARTING AND OPERATING Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected before rotating. The suggested rotation method is the “forward-cross” shown in the diagram. AUTOSTICK — IF EQUIPPED Autostick is a driver-interactive transaxle that offers manual gear shifting capability to provide you with more control.
STARTING AND OPERATING autostick lever to the AUTOSTICK position. The transaxle will remain in the current gear until an upshift or downshift is chosen. 177 • Downshifts from third to second gear above 66 mph (106 km/h) and from second to first gear above 37 mph (60 km/h) will be ignored. • You can start out in first, second, or third gear. Shifting into fourth gear can occur only after vehicle speed reaches 15 mph (24 km/h).
STARTING AND OPERATING FUEL REQUIREMENTS Your vehicle is designed to meet all emission regulations and provide excellent fuel economy when using high quality regular unleaded gasoline with an octane rating of 87. The use of premium gasoline is not recommended. The use of premium gasoline will provide no benefit over high quality regular gasolines, and in some circumstances, may result in poorer performance. Spark Knock Light spark knock at low engine speeds is not harmful to your engine.
STARTING AND OPERATING CAUTION! DO NOT use gasolines containing Methanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components. Problems that result from using methanol/gasoline blends are not the responsibility of the manufacturer. While MTBE is an oxygenate made from Methanol, it does not have the negative effects of Methanol.
STARTING AND OPERATING Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance, or damage the emission control system. • An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat.
STARTING AND OPERATING • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the trunk closed when driving your vehicle to prevent carbon monoxide and other poisonous exhaust gases from entering the vehicle.
STARTING AND OPERATING Fuel Requirements Your vehicle will operate on both unleaded gasoline with an octane rating of 87, or E-85 fuel, or any mixture of these two. For best results, a refueling pattern that alternates between E-85 and unleaded gasoline should be avoided.
STARTING AND OPERATING Replacement Parts Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol compatible parts. 183 ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door, on the driver’s side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle.
STARTING AND OPERATING NOTE: Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is properly tightened. The Malfunction Indicator Light will come on if the gas cap is not properly secured. Make sure that the gas cap is tightened each time the vehicle is refueled. NOTE: When the fuel nozzle “clicks” or shuts off, the fuel tank is full. NOTE: The fuel tank filler tube may have a restricting door about 50 mm (2 inches) down from the opening.
STARTING AND OPERATING VEHICLE LOADING Vehicle Loading Capacities Front Seat Occupants . . . . . . . . . . . . . . . . . . . . . . . 2 Rear Seat Occupants . . . . . . . . . . . . . . . . . . . . . . . . 2 Luggage . . . . . . . . . . . . . . . . . . . . . . 115 lbs. (52 kg) Rated Vehicle Capacity. . . . . . . . . . . . 715 lbs. (324 kg) TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.
STARTING AND OPERATING Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR.
STARTING AND OPERATING Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the Trailer Towing Weights (Maximum Trailer Weight Ratings) chart for the Max. GTW towable for your given drivetrain. 187 Trailer Hitch Classification Class Max. GTW (Gross Trailer Wt.
STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission Frontal Area Max. GTW (Gross Trailer Wt.) 2.4L Automatic/ 20 Sq. Ft Manual 2.7L Automatic/ 20 Sq. Ft. Manual Refer to local laws for maximum trailer towing speeds.
STARTING AND OPERATING Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents.
STARTING AND OPERATING Towing Requirements To promote proper break-in of your new vehicle drivetrain components the following guidelines are recommended: CAUTION! • Avoid towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may damage your vehicle. • During the first 500 miles (805 km) of trailer towing, limit your speed to 50 mph (80 km/h). Perform the maintenance listed in Section 8 of this manual. When towing a trailer, never exceed the GAWR, or GCWR, ratings.
STARTING AND OPERATING • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle automatic transmission in P for Park. With a manual transmission, shift the transmission into reverse. Always, block or ⬙chock⬙ the trailer wheels. • GCWR must not be exceeded. • Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. GVWR 2. GTW 3. GAWR 4.
STARTING AND OPERATING Towing Requirements — Trailer Brakes − Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. − An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required.
STARTING AND OPERATING 193 Towing Requirements — Trailer Lights & Wiring Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package may include a 4 and 7 pin wiring harness. Use a factory approved trailer harness and connector. NOTE: Do not cut or splice wiring into the vehicles wiring harness.
STARTING AND OPERATING Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve performance and extend transmission life by reducing excessive shifting and heat build up. This action will also provide better engine braking.
STARTING AND OPERATING Towing Tips — Electronic Speed Control (If Equipped) − Don’t use in hilly terrain or with heavy loads. − When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. − Use speed control in flat terrain and with light loads to maximize fuel efficiency.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 198 ▫ Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 198 䡵 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 208 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 199 䡵 Towing A Disabled Vehicle . . . . . . . . . . . . . . . 208 ▫ Preparations For Jacking . . . . . . . . . . . . . . . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER If it is necessary to leave the vehicle to go for service, the flasher system will continue to operate with the ignition key removed and the vehicle locked. NOTE: With extended use, the flasher may wear down your battery. IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. • On the highways — Slow down.
WHAT TO DO IN EMERGENCIES CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle. Idle the vehicle in Park with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H”, turn the engine off immediately, and call for service. WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant.
WHAT TO DO IN EMERGENCIES Preparations for Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, and set the parking brake. Place the gear selector in PARK. • Turn on the Hazard Warning Flasher, park vehicle on firm, level surface. • Put gear shift in park (automatic transmission) or reverse (manual transmission). • Set parking brake and turn off engine. • Passengers should not remain in the vehicle while the vehicle is being jacked.
WHAT TO DO IN EMERGENCIES 201 1. Block wheel diagonally opposite flat tire. 2. Remove the spare tire, scissors jack and lug wrench from stowage. 3. Before raising the vehicle, use lug wrench to carefully pry off wheel cover (if equipped with steel wheels) or center cap (if equipped with aluminum wheels). Loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground.
WHAT TO DO IN EMERGENCIES Jack Engagement Locations
WHAT TO DO IN EMERGENCIES 203 WARNING! WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. 6. Remove lug nuts and tire. 7. Mount spare tire. 8. Tighten all lug nuts on mounting studs. 9.
WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES IF BATTERY IS LOW WARNING! • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transaxle cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery, booster cables may be used to obtain a start from another vehicle.
WHAT TO DO IN EMERGENCIES WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and person injury could result. 205 5. Connect the other cable, first to the negative terminal of the booster battery and then to the jump start attachment of the vehicle with the discharged battery. Make sure you have a good contact on the engine. WARNING! Do not connect the cable to the negative post of the discharged battery.
WHAT TO DO IN EMERGENCIES 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan. WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle.
WHAT TO DO IN EMERGENCIES DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the front wheels to pull erratically to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels, particularly with high output engines. WARNING! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front wheels.
WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE If your vehicle is equipped with Traction Control, turn the system off before attempting to “rock” the vehicle. If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth between Reverse and First gear.
WHAT TO DO IN EMERGENCIES TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE (Flat towing with all four wheels on the ground) Automatic Transaxle Your vehicle may be towed under the following conditions: The gear selector must be in NEUTRAL, the distance to be towed must not exceed 15 miles (25 km), and the towing speed must not exceed 25 mph (40 km/h). If the transaxle is not operative, or if the vehicle is to be towed more than 15 miles (25 km), the vehicle must be towed with the front wheels off the ground.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 2.4L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 213 ▫ Power Steering — Fluid Check . . . . . . . . . . . . 227 䡵 2.7L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 214 ▫ Suspension Ball Joints . . . . . . . . . . . . . . . . . . 228 䡵 Onboard Diagnostic System — OBD II . . . . . . 215 ▫ Body Mechanism Lubrication . . . . . . . . . . . . . 228 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Appearance Care And Protection From Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . 241 䡵 Convertible Top Care . . . . . . . . . . . . . . . . . . . 246 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 251 ▫ Headlight Bulb Replacement . . . . . . . . . . . . . 251 ▫ Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246 ▫ Park, Turn Signal, Sidemarker Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 213 2.4L ENGINE 7 2.
MAINTAINING YOUR VEHICLE 2.7L ENGINE 2.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing.
MAINTAINING YOUR VEHICLE If your OBD system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD system to update. A recheck with the above test routine may then indicate that the system is now ready.
MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle.
MAINTAINING YOUR VEHICLE 219 • Day and night temperatures are below 32° F (0° C) • Stop and Go driving • Extensive engine idling. • Driving in dusty conditions • Short trips of less than 10 miles (16.2 km) • More than 50% of your driving is at sustained high speeds during hot weather, above 90° F (32° C) • Trailer towing Engine Oil Dipstick CAUTION! Overfilling or underfilling will cause aeration or loss of oil pressure. This could damage your engine.
MAINTAINING YOUR VEHICLE If none of these apply to you, then change your engine oil at every interval shown on schedule ⬙A⬙ of the ⬙Maintenance Schedules⬙ section of this manual. NOTE: Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or 6 months whichever comes first.
MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) 221 Synthetic Engine Oils You may use synthetic engine oils provided that the recommended oil quality requirements are met and the recommended maintenance intervals for oil and filter changes are followed. Materials Added To Engine Oils The manufacturer strongly recommends against the addition of any additives (other than leak detection dyes) to engine oil.
MAINTAINING YOUR VEHICLE Engine Oil Filter Selection All manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high quality filters should be used to assure most efficient service. Mopar Engine Oil Filters are high quality oil filters and are recommended. Spark Plugs Spark plugs must fire properly to assure engine performance and emission control.
MAINTAINING YOUR VEHICLE WARNING! The air cleaner can provide a measure of protection in the case of engine backfire. Do not remove the air cleaner unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine compartment before starting the vehicle with the air cleaner removed. Failure to do so can result in serious personal injury. Engine Fuel Filter A plugged fuel filter can cause hard starting or limit the speed at which a vehicle can be driven.
MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE Maintenance-Free Battery The top of the MAINTENANCE-FREE battery is permanently sealed. You will never have to add water, nor is periodic maintenance required. NOTE: The battery is stored in a compartment behind the left front fender and is accessible without removing the tire and wheel. Remote battery terminals are located in the engine compartment for jump starting.
MAINTAINING YOUR VEHICLE CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion. Apply grease to posts and clamps after tightening.
MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
MAINTAINING YOUR VEHICLE Fluid level should be maintained at the proper level indicated on the side of the reservoir. If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to Fluids, Lubricants, and Genuine Parts for correct fluid type. Suspension Ball Joints There are two upper front and rear suspension ball joints. Inspect these ball joints whenever under vehicle service is done.
MAINTAINING YOUR VEHICLE If you use a lubricant that cannot be dispensed directly into the lock cylinder, apply a small amount of the lubricant to the key. Insert the key into the lock cylinder, then proceed as described above, to distribute the lubricant within the lock cylinder. Pay attention to trunk hinges, especially during cold weather, to ensure ease of trunk operation.
MAINTAINING YOUR VEHICLE Windshield Wiper Blade Replacement • Lift the wiper arm away from the glass. • Push the release tab and slide the wiper blade assembly away from the wiper arm. Gently place the wiper arm on the windshield. • Install the new blade assembly onto the wiper arm tip until it locks in place. Windshield Washers The fluid reservoir in the engine compartment should be checked for fluid level at regular intervals.
MAINTAINING YOUR VEHICLE Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
MAINTAINING YOUR VEHICLE Cooling System WARNING! • When working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the OFF position. The fan is controlled by both the temperature of the engine cooling system and the pressure in the air conditioning system and can start at any time the ignition switch is in the ON position. • You or others can be badly burned by hot coolant or steam from your radiator.
MAINTAINING YOUR VEHICLE Selection Of Coolant Use only the manufacturer’s recommended coolant, refer to Fluids, Lubricants and Genuine Parts for correct coolant type. CAUTION! Mixing of coolants other than specified HOAT engine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible.
MAINTAINING YOUR VEHICLE Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated. NOTE: Mixing coolant types will decrease the life of the engine coolant and will require more frequent coolant changes.
MAINTAINING YOUR VEHICLE ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately. Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the engine off and cold, the level of the coolant in the bottle should be between the ranges indicated on the bottle.
MAINTAINING YOUR VEHICLE • Maintain coolant concentration at 50% HOAT engine coolant (minimum) and distilled water for proper corrosion protection of your engine which contains aluminum components. • Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean, also. • Do not change the thermostat for summer or winter operation.
MAINTAINING YOUR VEHICLE WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You may not have your full braking capacity in an emergency. Brake and Power Steering System Hoses When servicing the vehicle for scheduled maintenance, inspect surface of hoses and nylon tubing for evidence of heat and mechanical damage.
MAINTAINING YOUR VEHICLE Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning lamp shows system failure. Use only manufacturer’s recommended brake fluid, refer to Fluids, Lubricants and Genuine Parts for correct fluid type.
MAINTAINING YOUR VEHICLE Do not allow petroleum base fluid to contaminate the brake fluid as seal damage will result! Fuel System Hoses Electronic Fuel Injection high pressure fuel systems are designed with hoses and clamps which have unique material characteristics to provide adequate sealing and resist attack by deteriorated gasoline. You are urged to use only manufacturer specified hoses and clamps, or their equivalent in material and specification, in any fuel system servicing.
MAINTAINING YOUR VEHICLE Procedure For Checking Fluid Level The fluid level in the automatic transaxle should be checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly reduce the life of the transaxle and of the fluid. To properly check the automatic transaxle fluid level, the following procedure must be used: • The vehicle must be on level ground. • The engine should be running at curb idle speed for a minimum of 60 seconds. • Fully apply parking brake.
MAINTAINING YOUR VEHICLE • Police, taxi, limousine, commercial type operation, or trailer towing where the vehicle is driven regularly for more than 45 minutes of continuous operation. NOTE: Refer to Section 8 of this manual for maintenance schedules. If the transaxle is disassembled for any reason, the fluid and filter should be changed. Special Additives TThe manufacture strongly recommends against the addition of any additives to the transaxle.
MAINTAINING YOUR VEHICLE What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. The most common causes are: CAUTION! • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar.
MAINTAINING YOUR VEHICLE 243 • Use Mopar touch up paint or equivalent on scratches or chips as soon as possible. Your dealer has touch up paint to match the color of your vehicle. Never use cleaners that contain acid, oven cleaners or any abrasive metal cleaner as they will cause permanent staining and/or corrosion. • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible.
MAINTAINING YOUR VEHICLE You should not increase the gloss level, especially on top of the instrument panel top surface. Higher gloss levels will increase the reflectivity in the windshield that could decrease visibility under bright light driving conditions. WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm.
MAINTAINING YOUR VEHICLE Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters. Do not use scrapers or other sharp instruments which may scratch the elements. Instrument Panel Cover The instrument panel cover has a low glare surface which minimizes reflections in the windshield.
MAINTAINING YOUR VEHICLE CONVERTIBLE TOP CARE Immediate removal of any contaminant is recommended. Regular washing of the top will enhance its life and appearance, and make successive cleanings easier. Do not subject the top to excessive heat. Frequently vacuum the top and storage compartment. Washing Hand washing is highly recommended. Automatic car washing equipment can damage the top material. If you must use an automatic car wash, soft cloth systems are preferred.
MAINTAINING YOUR VEHICLE Vacuuming the top with a wet/dry shop vacuum will decrease the top’s drying time, ensure removal of all dirt, and delete streaks in the material. Multiple cleanings may be necessary to remove stubborn stains. If stains persist, contact your local dealership for further suggestions.
MAINTAINING YOUR VEHICLE FUSES Underhood Fuses (Power Distribution Center) A Power Distribution Center is located in the engine compartment, near the air cleaner. This information applies to vehicles built without the fuse and relay numbering embossed on the Power Distribution Center Top Cover. Interior Fuses Fuse Panel Cover The fuse access panel is behind the end cover at the left side of the instrument panel. To remove the panel, pull it out, as shown.
MAINTAINING YOUR VEHICLE Cavity 1 2 3 4 Fuse Circuit 30 Amp Blower Motor Green 10 Amp Red Right High Beam Headlight, High Beam Indicator 10 Amp Red Left High Beam Headlight 15 Amp Power Door Lock Switch Blue Illumination, Power Top Switch, Transmission Range Switch, Daytime Running Light Module (Canada), Power Windows, Anti-lock Brake System Module Cavity 5 6 7 8 9 10 249 Fuse Circuit 10 Amp Red Power Door Lock and Door Lock Arm/Disarm Switches, Vanity, Reading, Map, Rear Seating, Ignition, and Trun
MAINTAINING YOUR VEHICLE Cavity 11 12 13 14 15 16 17 18 19 Fuse Circuit 10 Amp Red Instrument Cluster, Transmission Control, Park/Neutral Switch, Body Control Module 10 Amp Red Left Low beam Headlight 20 Amp Yel- Right Low Beam Headlow light, Fog Light Switch 10 Amp Red Radio 10 Amp Red Turn Signal and Hazard Flashers, Wiper Switch, Seat Belt Control Module, Wiper Relays, Rear Window Defroster Relay 10 Amp Red Airbag Control Module 10 Amp Airbag Control Module 20 Amp Power Seat Switch, ReC/BRKR mot
MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Bulb Number Instrument Cluster . . . . . . . . . . . . . . . . . . . . . PC 194 ABS Indicator . . . . . . . . . . . . . . . . . . . . . . . . PC 161 Fog Indicators . . . . . . . . . . . . . . . . . . . . . . . . PC 161 Floor Console, Courtesy Light, Door Courtesy Light, Trunk Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 562 Climate Control Light . . . . . . . . . . . . . . . . . . . . . . 37 Traction Control Light . .
MAINTAINING YOUR VEHICLE 3. Gently pry the headlight assembly away from the fender as shown in the picture. This will free the ball stud from its retainer in the fender. Pull the headlight assembly away from the vehicle. 4. Turn the retaining ring counterclockwise and remove the bulb and socket assembly.
MAINTAINING YOUR VEHICLE 253 6. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 7. Reinsert the bulb and socket assembly and turn the retaining ring clockwise to secure the bulb. 8. Reinstall the headlight assembly. Park, Turn Signal, Sidemarker Bulb Replacement 1. Open the hood and remove the two headlight assembly mounting screws. Pull the headlight assembly away from the vehicle. 5. Pull the bulb out of the socket and replace the bulb.
MAINTAINING YOUR VEHICLE 2. Gently pry the headlight assembly away from the fender as shown in the picture. This will free the ball stud from its retainer in the fender. Pull the headlight assembly away from the vehicle. 3. Turn the bulb socket counterclockwise and remove the bulb and socket assembly. 4. Pull the bulb out of the socket, replace the bulb, and reinstall the bulb and socket to the headlight assembly. Reinstall the headlight assembly.
MAINTAINING YOUR VEHICLE Fog Light Bulb Replacement 1. Remove the screw securing the light assembly to the front fascia. 255 4. Turn the bulb and socket assembly counterclockwise to remove it from the housing. 7 2. Pull the bulb and socket assembly away from the vehicle to expose the bulb and socket assembly. 3. Disconnect the wiring connector from the bulb and socket assembly. 5. Install the new bulb and socket assembly, reattach the wiring connector, and reinstall the fog light assembly.
MAINTAINING YOUR VEHICLE Rear Light Bulb Replacement 1. Open the trunk and pull the trunk liner away to expose the wiring connector and light housing plastic retainers. 2. Disconnect the wiring connector as shown and remove the plastic retainers. Remove the light housing from the vehicle. 3. Turn the bulb socket counterclockwise to remove it from the housing. Remove the bulb and reinstall the bulb and socket assembly. 4. Reinstall the light housing and reconnect the wiring connector.
MAINTAINING YOUR VEHICLE License Plate Bulb Replacement 1. Locate both small slots on the outboard side of the license lamp. Using a small screwdriver, remove the entire housing. 2. Turn the bulb socket counterclockwise to remove it from the housing. Pull the bulb out of the socket. Replace the bulb and snap it back into place on the housing of the chrome appliqué. Headlight Aiming The headlights on your new vehicle were aimed at the factory. The factory setting was made at a no load setting.
MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Spark Plugs Oil Filter (2.4L Engine) Oil Filter (2.7L Engine) Fuel Selection Fluid, Lubricant, or Genuine Part Mopar威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Use API Certified engine oil. SAE 5W-20 and SAE 5W-30 are recommended.
MAINTAINING YOUR VEHICLE 259 Chassis Component Automatic Transaxle Brake Master Cylinder Power Steering Reservoir Steering Gear & Linkage, Ball Joints, Prop Shafts & Yokes, Wheel Bearings Fluid, Lubricant, or Genuine Part Mopar威 ATF+4 Automatic Transmission Fluid. Mopar威 DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. Mopar威 Power Steering Fluid + 4, Mopar威 ATF+4 Automatic Transmission Fluid.
MAINTENANCE SCHEDULES CONTENTS M A I N T E N A N C E 䡵 Emission Control System Maintenance . . . . . . 262 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 265 䡵 Maintenance Schedules . . . . . . . . . . . . . . . . . . 262 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 262 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5,000 km) or 3 months, whichever comes first and follow schedule B of the “Maintenance Schedules” section of this manual. NOTE: If ANY of these apply to you then flush and replace the engine coolant every 100,000 miles (160,000 km) or 60 months, whichever comes first, and follow schedule B of the ⬙Maintenance Schedules⬙ section of this manual.
M A I N T E N A N C E S C H E D U L E S 8 264 MAINTENANCE SCHEDULES • Check all lights and all other electrical items for correct operation. • Check rubber seals on each side of the radiator for proper fit. At Each Oil Change • Change the engine oil filter. • Inspect the exhaust system. • Inspect the brake linings, hoses and calipers. • Inspect the CV joints and front and rear suspension components. • Check the automatic transmission fluid level. • Check the brake master cylinder fluid level.
SCHEDULE “B” 265 M A SCHEDULE “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. Change the automatic transmission fluid and filter every 60,000 miles (96 000 km) if the vehicle is usually operated under one or more of the conditions marked with an 〫. • Taxi, police or delivery service (commercial ser- I N vices).〫 T • Day or night temperatures are below 32° F (0° C).
M 266 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Inspect the air cleaner filter and replace if E necessary.* S C H E D U L E S 8 Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Rotate the tires.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if required.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if required. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Check and replace, if necessary, the PCV valve. * Replace the spark plugs on 2.4 liter engine. Rotate the tires.
M 268 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Inspect the air cleaner filter and replace if E necessary.* S C H E D U L E S 8 Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Rotate the tires.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if required. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the ignition cables on 2.4 liter engine. Replace the accessory drive belts on the 2.7 liter engine.
M 270 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not A replaced at 3 months. N C Inspect the air cleaner filter and replace if E necessary.* S C H E D U L E S 8 Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if required. Replace the engine timing belt on 2.4 liter engine. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.
SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, if not replaced at 3 months. Inspect the air cleaner filter and replace if necessary.* Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on the 2.7 liter engine. Check and re-tension accessory drive belts on 2.7 liter engine. Replace the accessory drive belts on 2.4 liter engine. Rotate the tires. Flush and replace the engine coolant, if not replaced at 60 months.
M 272 SCHEDULE “B” A I N Miles T (Kilometers) E N Change engine oil and engine oil filter, if not replaced at A 3 months. N C Inspect the air cleaner filter and replace if necessary.* E Replace the air cleaner filter. S C H E D U L E S 8 Replace the spark plugs on the 2.4 liter engine. Replace the ignition cables on the 2.4 liter engine. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the accessory drive belts on 2.7 liter engine.
SCHEDULE “A” 273 M SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect the air cleaner filter and replace if necessary.* Replace the air cleaner filter. Replace the spark plugs on 2.4 liter engine. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Rotate the tires.
M 274 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Inspect the air cleaner filter and replace if E required.* S C H E D U L E S 8 Replace the air cleaner filter. Inspect and check tension for power steering belt (2.4 Liter Engine). Adjust or replace if required. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.4 liter engine.
SCHEDULE “A” Miles 78,000 (Kilometers) (130 000) [Months] [78] Change engine oil and engine oil filter. X Inspect the air cleaner filter and replace if X required.* Replace the air cleaner filter. Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.4 liter engine. Replace the spark plugs on 2.7 liter engine. Check and replace, if necessary, the PCV valve. *‡ Check and re-tension alternator drive belts on 2.7 liter engine.
M 276 SCHEDULE “A” A I N Miles T (Kilometers) E N [Months] A Change engine oil and engine oil filter. N C Inspect the air cleaner filter and replace if required.* E Replace the air cleaner filter. S C H E D U L E S 8 108,000 (190 000) [108] X X ‡ This maintenance is not required if previously replaced. 120,000 (210 000) [120] X X Inspect the front and rear brake pads, linings, rotors, rear drums and shoes. Replace the spark plugs on 2.4 liter engine. Check and replace, if necessary, the PCV valve.
SCHEDULE “A” WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280 ▫ Prepare For The Appointment . . . . . . . . . . . . 280 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 280 䡵 Reporting Safety Defects . . . . . . . . . . . . . . . . . 283 ▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 283 䡵 Publication Order Forms . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
IF YOU NEED CONSUMER ASSISTANCE • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center.
IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unexpected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands behind only the manufacturer’s Service Contracts. If you purchased a manufacturer’s Service Contract, you will receive Plan Provisions and an Owner Identification Card in the mail within three weeks of your vehicle delivery date.
IF YOU NEED CONSUMER ASSISTANCE REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
IF YOU NEED CONSUMER ASSISTANCE Corporation vehicles. A complete working knowledge of the vehicle, system and/or components is written in straightforward language with illustrations, diagrams and charts. • Diagnostic Procedure Manuals. Filled with diagrams, charts and detailed illustrations, these practical manuals make it easy for students and technicians to find and fix problems on computercontrolled vehicle systems and features.
IF YOU NEED CONSUMER ASSISTANCE Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1 1/2) times as well on the government course as a tire graded 100.
IF YOU NEED CONSUMER ASSISTANCE WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.
INDEX 10
INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . 155 ABS (Anti-Lock Brake System) . . . . . . . . . . . . . 155 Adding Engine Coolant (Antifreeze) . . . . . . . . . 233 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 183 Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . 230 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . 179 Aiming Headlights . . . . . . . . . . . . . . . . . . . . . . 257 Air Cleaner, Engine (Engine Air Cleaner Filter) .
INDEX Autostick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 Auxiliary Power Outlet . . . . . . . . . . . . . . . . . . . 79 Ball Joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Emergency Starting . . . . . . . . . . . . . . . . . . . . 204 Gas Caution . . . . . . . . . . . . . . . . . . . . . . 206,225 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 Jump Starting . . . . . . .
INDEX Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . 199 Charging System Light . . . . . . . . . . . . . . . . . . . 90 Chart, Tire Sizing . . . . . . . . . . . . . . . . . . . . . . . 160 Check Engine Light (Malfunction Indicator Light) . . . . . . . . . . . . . . 216 Checking Your Vehicle For Safety . . . . . . . . . . . . 43 Child Restraint . . . . . . . . . . . . . . . . . . . 34,36,39,40 Child Restraint Tether Anchors . . . . . . . . . . . . . 39 Cigar Lighter . . . . . . . . . . .
INDEX Crankcase Emission Control System . . . . . . . . . 224 Cruise Control (Speed Control) . . . . . . . . . . . . . 72 Cruise Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Customer Assistance . . . . . . . . . . . . . . . . . . . . 280 Daytime Running Lights . . . . . . . . . . . . . . . . . . 68 Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . . 217 Defroster, Rear Window . . . . . . . . . . . . . . . . . . 139 Defroster, Windshield . . . . . . . . . . . . . . .
INDEX Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232 Exhaust Gas Caution . . . . . . . . . . . . . . . . . . 180 Fails to Start . . . . . . . . . . . . . . . . . . . . . . . . . 148 Fuel Requirements . . . . . . . . . . . . . . . . . 178,257 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 218,257,258 Oil Change Interval . . . . . . . . . . . . . . . . . . . 219 Oil Selection . . . . . . . . . . . . . . . . . . . . . . 220,257 Oil Synthetic . . . . . . . . . . . . . . . . .
INDEX Fluids, Lubricants and Genuine Parts . . . . . . . . 258 Fog Light Service . . . . . . . . . . . . . . . . . . . . . . . 255 Fog Lights . . . . . . . . . . . . . . . . . . . . . . . . 68,91,255 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . 208 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178 Adding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 Additives . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 Clean Air . . . . . . . . . . . . .
INDEX Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244 High Beam . . . . . . . . . . . . . . . . . . . . . . . . . 69,90 High Beam/Low Beam Select Switch . . . . . . . 69 Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Time Delay . . . . . . . . . . . . . . . . . . . . . . . . 68,69 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129,136 Heater, Engine Block . . . . . . . . . .
INDEX Latches Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Lead Free Gasoline . . . . . . . . . . . . . . . . . . . . . . 178 Leaks, Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44,64 Airbag . . . . . . . . . . . . . . . . . . . . . . . . 32,34,43,89 Anti-Lock Warning . . . . . . . . . . . . . . . . . . . . .
INDEX Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Lower Anchors and Tether for CHildren (LATCH) . . . . . . . . . . . . 37,39 Lubricants . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . 228 Luggage/Cargo Capacity . . . . . . . . . . . . . . . . . 185 Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Onboard Diagnostic System . . . . . . . . . . . . 215,216 Opener, Garage Door (HomeLink威) . . . . . . . . . . 75 Operator Manual (Owner’s Manual) . . . . . . . . . . 4 Overdrive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 Overheating, Engine . . . . . . . . . . . . . . . . . . . . . 198 Owner’s Manual (Operator Manual) . . . . . . . 4,283 Paint Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241 Paint Damage . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Reminder, Seat Belt . . . . . . . . . . . . . . . . . . . . . . 27 Remote Keyless Entry (RKE) . . . . . . . . . . . . . . . 15 Remote Sound System (Radio) Controls . . . . . . 126 Remote Trunk Release . . . . . . . . . . . . . . . . . . . . 20 Replacement Tires . . . . . . . . . . . . . . . . . . . . . . 173 Reporting Safety Defects . . . . . . . . . . . . . . . . . 283 Restraint, Head . . . . . . . . . . . . . . . . . . . . . . . . . 63 Restraints, Child . . . . . . . . . . . . . . . . . . . .
INDEX Service Manuals . . . . . . . . . . . . . . . . . . . . . . . . 283 Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . 99 Side Window Demisters (Defrosters) . . . . . . 134,139 Signals, Turn . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Slippery Surfaces, Driving On . . . . . . . . . . . . . 207 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . 170,171 Spark Plugs . . . . . . . . . . . . . . .
INDEX General Information . . . . . . . . . . . . . . . . . . . 167 High Speed . . . . . . . . . . . . . . . . . . . . . . . . . 169 Inflation Pressures . . . . . . . . . . . . . . . . . . . . 168 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . 173 Load Capacity . . . . . . . . . . . . . . . . . . . . 163,164 Quality Grading . . . . . . . . . . . . . . . . . . . . . . 284 Radial . . . . . . . . . . . . . . . . . . .
INDEX Tread Wear Indicators . . . . . . . . . . . . . . . . . . . 172 Trip Computer . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Trip Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Trip Odometer Reset Button . . . . . . . . . . . . . . . . 92 Trunk Release, Emergency . . . . . . . . . . . . . . . 20,21 Trunk Release Remote Control . . . . . . . . . . . . . . 20 Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . . 68,90 Underhood Fuses . . . . . . . . . . . . . . . . . .
NOTES